The Hertzian contact theory, as well as most of the other classical theories of normal and tangential contact, provides displacements and the distribution of normal and tangential stress components directly in the contact surface. However, other components of the full stress tensor in the material may essentially influence the material behaviour in contact. Of particular interest are principal stresses and the equivalent von Mises stress, as well as the gradient of the hydrostatic pressure. For many engineering and biomechanical problems, it would be important to find these stress characteristics at least in the contact plane. In the present paper, we show that the complete stress state in the contact plane can be easily found for axially symmetric contacts under very general assumptions. We provide simple explicit equations for all stress components and the normal component of the gradient of hydrostatic pressure in the form of one-dimensional integrals.

Solid-state transformer (SST) is a promising technology for smart grids due to its flexible power control (better reliability) and high efficacy (by decreasing losses) compared with traditional transformers. The SST is designed in tandem with three stages, i.e., the input, isolation, and output stages. As three converter stages are used to design the SST to make a more reliable device in practice, it is highly prone to instabilities. Moreover, the key objective of SST design is to implement a modern power distribution system to make it more intelligent and reliable. The stability issue can be even more complicated by the presence of distributed energy resources in the distribution system. Thus, the stability of SST must be measured prior to /during the design, and to determine, a state-space model is used, which is developed in this paper. Each stage of SST is modeled with its controller, and the system's stability is measured through the controllability and observability test. Further, the conversion from state-space to transfer function model is done, and the stability of SST is shown using frequency and time-domain diagrams. With these, the different plots, namely, the Bode plot, Nyquist plot, Nichols chart, Root locus, pole-zero plot, and Eigen plot, are used to ascertain the relative and absolute stability. Finally, the SST Simulink model is tested and validated through hardwate-in-the-loop simulation, i.e., OPALRT, to show its effectiveness and applicability.

Li₇La₃Zr₂O₁₂Solid-state reaction was used for Li₇La₃Zr₂O₁₂ material synthesis from Li₂CO₃, La₂O₃ and ZrO₂ powders. Phase investigation by XRD, SEM and EDS methods of Li₇La₃Zr₂O₁₂ were carried out. The molar heat capacity of Li₇La₃Zr₂O₁₂ at constant pressure in the temperature range 298-800 K should be calculated as Cp,m = 518.135+0.599 × T - 8.339 × T−2, where T is absolute temperature, . Thermodynamic characteristics of Li₇La₃Zr₂O₁₂ were determined as next: entropy S0298 = 362.3 J mol-1 K-1, molar enthalpy of dissolution ΔdHLlZO = ˗ 1471.73 ± 29.39 kJ mol−1, the standard enthalpy of formation from elements ΔfH0 = ˗ 9327.65 ± 7.9 kJ mol−1, the standard Gibbs free energy of formation ∆f G0298 = ˗9435.6 kJ mol-1.

The garnet Li₇La₃Zr₂O₁₂ (LLZO) has been widely investigated because of its high conductivity, wide electrochemical window and chemical stability to lithium metal. However, the usual preparation process of LLZO requires a long time of high-temperature sintering and a lot of mother powders against the lithium evaporation. The submicron Li₆.6La₃Zr₁.6Nb₀.4O₁₂ (LLZNO) powders are prepared by conventional solid-state reaction method and attrition milling process, which are stable cubic phase and have high sintering activity, and Li stoichiometric LLZNO ceramics are obtained by sintering at a relative lower temperature or for a short time by using these powders which are difficult to control under high sintering temperature and long sintering time. The particle size distribution, phase structure, microstructure, distribution of element, total ionic conductivity, relative density and activation energy of submicron LLZNO powders and LLZNO ceramics are tested and analyzed by laser diffraction particle size analyzer, XRD, SEM, EIS and Archimedean method. The total ionic conductivity of sample sintered at 1200 °C for 30 min is 5.09 × 10-4 S·cm-1, the activation energy is 0.311 eV, and the relative density is 87.3%, and sintered at 1150 °C for 60 min total ionic conductivity is 3.49 × 10-4 S·cm-1, the activation energy is 0.316 eV, and the relative density is 90.4%. At the same time, all-solid-state batteries are assembled with LiMn₂O₄ as positive electrode and submicron LLZNO powders as solid state electrolyte. After 50 cycles, the discharge specific capacity is 105.5 mAh/g and the columbic efficiency is above 95%.

A simple line of reasoning, based on the most fundamental concepts of thermodynamics, yields some intriguing results for a better understanding of the processes occurring in the observable Universe. Gravitational mass must be continuously generated within an expanding thermodynamic system for this system to remain closed. The Second Law is a direct consequence of this production of mass. Simple expressions for the entropy and temperature of the Universe were obtained and the results agree well with observable values. Furthermore, it is demonstrated that the conservation laws within the Universe are independent of its energy density. Based on the solution for the quantum state of the Universe, it is conjectured that the Second Law is incomplete and must be complemented to a conservation law, which takes into account the growth of the amount of information within the Universe. Once the Second Law is complemented to a conservation law, the importance of mass generation within the Universe becomes well pronounced – not only gravitational effects play the role of an organising force, but also the amount of mass within the Universe defines both the amount of information within the Universe and the level of the Universe’s complexity.

In the context of intelligent and integrative lighting, in addition to the need for color quality and brightness, the non-visual effect is essential. This refers to the retinal ganglion cells (ipRGCs) and their function, first proposed in 1927. The melanopsin action spectrum has been published in CIE S 026/E: 2018 with the corresponding melanopic equivalent daylight (D65) illuminance (mEDI), melanopic daylight (D65) efficacy ratio (mDER) and 4 other parameters. Due to the importance of mEDI and mDER, this work synthesizes a simple computational model of mDER as the main research objective, based on a database of 4214 practical spectral power distributions (SPDs) of daylight, conventional, LED, and mixed light sources. In addition to the high correlation coefficient R2 of 0.96795 and the 97% confidence offset of 0.0067802, the feasibility of the mDER model in intelligent and integrated lighting applications has been extensively tested and validated. The uncertainty between the mEDI calculated directly from the spectra and that obtained by processing the RGB sensor and applying the mDER model has reached ± 3.3% after an appropriate matrixing process and proper illumination characterization combined with the successful mDER calculation model. This result opens the potential of low-cost RGB sensors for applications in intelligent and integrative lighting systems to optimize and compensate the non-visual effective parameter mEDI using daylight and artificial light in indoor spaces. The goal of the research on RGB sensors and the corresponding processing method are also presented and their feasibility is methodically demonstrated. A comprehensive investigation with a huge amount of color sensor sensitivities is necessary in a future work of other researches.

It is well known that the photon trajectories follow a curved path in a gravitational field. We explore here the gravitational bending of electric field lines. It seems that the electric field lines of a charge, supported in a gravitational field, follow exactly the trajectories of photons emitted isotropically from a source situated at the charge location. From a detailed examination of the electrostatic field of a charge accelerated uniformly in the instantaneous rest frame, exploiting the strong principle of equivalence, one can determine the bending of the electric field lines of a charge in a gravitational field. The fraction of electric field lines crossing a surface, stationary above or below the charge in the gravitational field, is shown to be exactly similar to the fraction of photon trajectories, emitted from a source placed at the charge location, intersecting that surface. On the other hand, for a freely falling charge in the gravitational field there is no such bending of electric field lines. The field lines continue to extend in radial straight lines from the instantaneous 'present' position of the charge, as do the trajectories of photons streaming away from the instantaneous position of a freely falling source in the gravitational field. The electric field configuration of a freely falling charge in the gravitational field is shown to be exactly the same as that of a charge moving uniformly in an inertial frame with velocity equal to the instantaneous ``present'' velocity of the freely falling charge.

This paper investigates whether currency risk is priced differently in the different sectors (industrial, financial, and basic materials) of equity markets in a sample of developed United States of America (USA) and developing economies (Brazil, India, Poland, and South Africa). The paper makes use of the following techniques: (i) Univariate Autoregressive Fractionally Integrated Moving Average and Exponential General Autoregressive Conditional Heteroskedastic (ARFIMA-EGARCH), (ii) the Markov-Switching method (MS), and (iii) the Canonical Vine Copulas (C-Vine) techniques. Using a sample of daily data made of the foreign exchange rate against the domestic currency and equity market sectors; our findings show that there is an asymmetry effect between equities markets and the foreign exchange rate: there is a heterogeneous, strong, and positive dependence between the two. Higher equities prices are associated with depreciation of local currencies, according to US dollar (USD) exchange rates. In addition, we find that the selected emerging economies are pricing a positive and considerable currency risk. The pricing of currency risk has a varied effect in both regimes representing the states of the economy. In fact, when currency risk pricing has a beneficial impact on certain sectors of the economy, investors predict better returns.

The COVID-19 appears as a catastrophic health risk with psychological, emotional, social and relational implications. From the early stages of the virus spread, the elderly population was identified as the most vulnerable and the health authorities have rightly focused on such frailest population. Conversely, less attention was paid to emotional and psychological dimension of children and adolescents. Actually, they were less at risk quoad vitam or quoad valetudinem, nevertheless they had to face a reality of anxiety, fears and uncertainties. The current study investigated state anxiety and emotion awareness in a healthy sample of older adolescents, 84 females and 64 males, aged 17 to 19, during the pandemic lockdown, using Self-rating Anxiety Scale and the Italian Emotion Awareness Questionnaire. An unexpected anxious phenomenology, impacting the anxiety ideo-affective domain, was found, while the somatic symptomatology appeared to be less severe. The highest anxiety symptom were the breathing difficulties. These findings supported the hypothesis that the COVID-19 pandemic may be a risk condition for an increased state anxiety in older adolescents and suggest the need to provide 1. an effective, empathic communication system with the direct participation of older adolescents, 2. a psychological counseling service for stress management of adolescents.

In this paper, optimum parameters of Tuned Mass Dampers (TMD) are considered to control the responses of 10-story shear building under harmonic loading and 22 set of seismic records of FEMA-P695. The criterion used to obtain the optimum parameters is to select mass ratio, the frequency (tuning) and damping ratio that would result in smallest lateral displacements. State-space equations of motion are presented to compute the structural responses by developing a MATLAB file. A 10-story shear building is presented as a case study to assess the effects of TMDs on the multi-story structures. The results indicate that using TMD can reduce structural responses up to the average 20% under earthquake excitation and up to 90% under harmonic loadings. TMDs are not always effective under any type of ground motion; therefore, being aware of the given location is significant to design TMDs properly.

In cosmology, the cosmic curvature $K$ and the cosmological constant $\Lambda$ are two most important parameters, whose values have strong influence on the behavior of the universe. By analyzing the energy-momentum tensor and equations of state of ideal gas, scalar, spinor and vector potential in detail, we find that the total mass density of all matter is always positive, and the initial total pressure is negative. Under these conditions, by qualitatively analyzing the global behavior of the dynamical equation of cosmological model, we get the following results: (i) $K= 1$, namely, the global spatial structure of the universe should be a 3-dimensional sphere $S^3$. (ii) $0\le\Lambda < 10 ^ {-24} {\rm ly} ^ {-2}$, the cosmological constant should be zero or an infinitesimal. (iii) $a(t)>0$, the initial singularity of the universe is unreachable, and the evolution of universe should be cyclic in time. This means that the initial Big Bang is impossible at all. Since the matter components considered are quite complete and the proof is very elementary and strict, these logical conclusions should be quite reliable. Obviously, these conclusions will be much helpful to correct some popular misconceptions and bring great convenience to further research other problems in cosmology such as property of dark matter and dark energy.

The possibility of using graphane monolayer crystals as the electrode material is becoming popular. Graphane is stable at room temperature and has large surface area, but its chemical inertness hinders its direct interactions with Li ions. In this study, we performed density functional theory calculations to study the energetic stability, structural and electronic properties of Li on graphane with various CH divacancy configurations (v12, v13 and v14 ). The results show that adsorption of Li atom reduces the formation energy of the CH divacancy configurations. The Li-v12 is most stable with the highest binding energy of 3.25 eV/Li and relaxes to in-plane with other C atoms. Altering the Li charge state to have Li−1-v12 or Li+1 -v12 affects the energetic stability and electronic characters of Li-v12 . The Li−1-v12 (Li +1-v 12 ) enhances (reduces) the binding force between Li and v 12 configuration, and furthermore it improves (deteriorates) the conductivity of the structure. Further investigation of graphane with vacancies is encouraged due to these intriguing observations, as it holds promise for potential utilization as an electrode material.

The interactions of metal ions with fulvic acids resulted in changes in the particle size and charge. Particle size distribution was trimodal for fulvic acids, bimodal for fulvic complexes with calcium and magnesium, and copper-fulvic complexes had only one size fraction. The compensation of negative charge of carboxylic and phenolic functional groups by positive charged metal ions resulted in the increase in zeta potential which was getting closer to zero in the case of copper-fulvic complexes. However, all metal humic complexes behaved as colloidally unstable which resulted in visually observable sedimentation. Calorimetric measurements provided positive values of changes in enthalpy which indicated endothermic processes. In contrast quantum chemical calculations as well as experiments with model compounds provided negative values indicated exothermic processes. Changes in Gibbs energy were determined as negative and changes in entropy as positive which meant spontaneous processes.

In order to improve the charge collection efficiency, we simulated and experimentally tested the doping structure of the electron multiplication layer in EBCMOS. In this paper, we simulate the charge collection efficiency of EBCMOS under different doping methods by modeling the collisional scattering of electrons with solid atoms in semiconductor materials and combining the transport trajectories of electrons in the electron multiplication layer, the simulation results indicate that using a layered doping structure to reduce the thickness of the index heavily doped layer can effectively optimize the electric field distribution in the electron multiplier layer and reduce the recombination rate of electrons. The optimized doping structure has a significant effect on improving charge collection efficiency. Based on the simulation results, doped samples were prepared and tested. The test results showed that the charge collection efficiency obtained under the condition of a P-type silicon substrate thickness of 7μm and an index heavily doped layer thickness of 1μm was 72.65%, reducing the thickness of the index heavily doped layer to 0.1μm, the charge collection efficiency obtained can reach 86.27%, which proves that reducing the thickness of the index heavily doped layer can effectively improve the charge collection efficiency of EBCMOS devices.

A chronically stable electrode material with low impedance for recording neural activity and high charge-injection capacity for functional electro-stimulation is desirable for the fabrication of implantable microelectrode arrays that aims to restore impaired or lost neurological functions in humans. For this purpose, we have investigated the electrochemical properties of sputtered ruthenium oxide (RuOx) electrode coatings, deposited on planar microelectrode arrays, using an inorganic model of interstitial fluid (model-ISF) at 37o C as the electrolyte. Through a combination of cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) modelling study we have established the contribution of faradaic reaction as the major charge-injection contributor within the safe neural stimulation potential window of 0.6 V vs Ag|AgCl. We have also established the reversibility of the charge-injection process for sputtered RuOx film by applying constant charge-per-phase current stimulations at different pulse widths and by comparing the magnitudes of leading and trailing access voltages during voltage transient measurements. Finally, the impedance of the sputtered RuOx film was found to be reasonably comparable in both its oxidized and reduced states, although electronic contribution from capacitive double-layer was found to be slightly higher for the completely oxidized film around 0.6 V than its reduced counterpart around -0.6V.

Memristors were proposed in the early ’70s of the XXth century by Leon Chua as a new electrical element linking the charge and the flux. Since that first introduction, these devices have positioned themselves to be considered as possibly fundamental for the new generations of electronic devices. It has to be mentioned that actual memristors have only been recognized to exist as physical elements. In this paper, we apply a modeling framework to generate a model describing experimental measurements performed on a ReRAM. We show how to apply the Dynamic Route Map technique in the general case to obtain an approximation to the differential equation that determines the behaviour of the device.

Evaluating new, promising organic molecules to make next-generation organic optoelectronic devices necessitates the evaluation of charge carrier transport performance through the semi-conducting medium. In this work, we utilize quantum chemical calculations (QCC) and kinetic Monte Carlo (KMC) simulations to predict the zero-field hole mobilities of ~100 morphologies of the benchmark polymer poly(3-hexylthiophene), with varying simulation volume, structural order, and chain-length polydispersity. Morphologies with monodisperse chains were generated previously using an optimized molecular dynamics force-field and represent a spectrum of nanostructured order. We discover that a combined consideration of backbone clustering and system-wide disorder arising from side-chain conformations are correlated with hole mobility. Furthermore, we show that strongly interconnected thiophene backbones are required for efficient charge transport. This definitively shows the role "tie-chains" play in enabling mobile charges in P3HT. By marrying QCC and KMC over multiple length- and time-scales, we demonstrate that it is now possible to routinely probe the relationship between molecular nanostructure and device performance.

We review the basics of nuclear binding energy scheme assumed to be associated with the existence of a new strong elementary charge associated with square root of reciprocal of the strong coupling constant.

Chinese-speaking parents are argued to use less cognitive mental-state-talk than their English-speaking counterparts due to their goals in socializing their children to follow an interdependence script. To extend this research, we investigated bilingual Mandarin-English Singaporean mothers who associate different functions for each language as prescribed by their government: English for school and Mandarin for in-group contexts. English and Mandarin maternal mental-state-talk from bilingual Mandarin-English mothers with their toddlers was examined. Mothers produced more cognitive terms in English than in Mandarin and more desire terms in Mandarin than in English. We show that mental-state-talk differs between bilingual parents’ languages, suggesting that mothers adjust their mental-state-talk to reflect each language’s function.

The article examines church architecture in modern Russia. The historical processes of the development of church architecture are analyzed and systematized not only from the point of view of formal stylistic but also global significance. For this purpose, for the first time, a wide range of sources containing information on the sacred component of church art and on the monuments of temple architecture was studied. At the same time, many fragments of sources were first translated into English. The article uses historical and retrospective research methods that allowed to study the theoretical legacy of the modern period in the history of Russia and at the same time to generalize the place of Russian church architecture in the general context of European architectural development.

This article presents a review of resources for batteries with a specific focus on sustainability aspects related to raw materials, electrode and electrolyte chemistries suitable for the automobile industry. We emphasize the importance of prioritizing sustainability in battery technology evolution, which is expected to shift towards earth-abundant materials. One notable advancement in this direction is the utilization of glass solid-state electrolytes, known for their high ionic conductivity, low electronic conductivity, and high dielectric constant. However, our review suggests that further research should explore synthesis methods to modify anisotropic properties, enhancing the performance of solid-state electrolytes, particularly in facilitating the flow of ions.

Accurate and efficient determination of excited-state polarizabilities (α) is an open problem both experimentally and computationally. Following our previous work, [Phys. Chem. Chem. Phys. 2023, 25, 2131−2141], where one can employ simple ground-state density-based functions from the information-theoretic approach (ITA) to accurately and efficiently predict the macromolecular polarizabilities, we aim to predict the lowest excited-state polarizabilities in this work. The philosophy is to use density-based functions to depict the excited-state polarizabilities. As a proof-of-principle application, employing 2-(2′-hydroxyphenyl)benzimidazole and its derivatives as model systems, we have verified that either with the ground-state (S0) or excited-state (S1) densities as input, ITA quantities can be strongly correlated with the excited-state polarizabilities. When the transition densities are considered, both S0 and S1 polarizabilities are in good relationships with some ITA quantities. Furthermore, excitation and emission energies can be predicted based on multivariant linear regression equations of ITA quantities.

The purpose of this paper is to build a new bridge between category theory and a generalized probability theory known as noncommutative probability or quantum probability, which was originated as a mathematical framework for quantum theory, in terms of states as linear functional defined on category algebras. We clarify that category algebras can be considered as generalized matrix algebras and that the notions of state on category as linear functional defined on category algebra turns out to be a conceptual generalization of probability measures on sets as discrete categories. Moreover, by establishing a generalization of famous GNS (Gelfand-Naimark-Segal) construction, we obtain a representation of category algebras of †-categories on certain generalized Hilbert spaces which we call semi-Hilbert modules over rigs.

Organisms in the wild have cryptic life stages that are sensitive to changing environmental conditions and can be difficult to survey. In this study, I used mark-recapture methods to repeatedly survey Anaea aidea (Nymphalidae) caterpillars in nature, then modeled caterpillar demography as a hidden Markov process to assess if temporal variability in temperature and density influence the survival and growth of A. aidea over time. Individual encounter histories result from the joint likelihood of being alive and observed in a particular stage, and I included hidden states by separating demography and observations into parallel and independent processes. I constructed a demographic matrix containing the probabilities of all possible fates for each stage, including hidden states, e.g., eggs and pupae. I observed both dead and live caterpillars with high probability. Peak caterpillar abundance attracted multiple predators, and survival of fifth instars declined as per capita predation rate increased through spring. A time lag between predator and prey abundance was likely the cause of improved fifth instar survival estimated at high density. Growth rates showed an increase with temperature, but the most likely model did not include temperature. This work illustrates how state-space models can include unobservable stages and hidden state processes to evaluate how environmental factors influence vital rates of cryptic life stages in the wild.

The world is currently experiencing the fourth industrial revolution driven by the newest wave of digitisation in the manufacturing sector. The term Industry 4.0 (I4.0) represents at the same time: a paradigm shift in industrial production, a generic designation for sets of strategic initiatives to boost national industries, a technical term to relate to new emerging business assets, processes and services, and a brand to mark a very particular historical and social period. I4.0 is also referred to as Industrie 4.0 the New Industrial France, the Industrial Internet, the Fourth Industrial Revolution and the digital economy. These terms are used interchangeably in this text. The aim of this article is to discuss major developments in this space in relation to the integration of new developments of IoT and cyber physical systems in the digital economy, to better understand cyber risks and economic value and risk impact. The objective of the paper is to map the current evolution and its associated cyber risks for the digital economy sector and to discuss the future developments in the Industrial Internet of Things and Industry 4.0.

Quasi-bound state in the continuum (QBIC) can effectively enhance the interaction of terahertz (THz) wave with matters due to the tunable high-Q property, which has a strong potential application in detection of low-concentration biological samples in the THz band. In this paper, a novel THz metamaterial sensor with a double-chain separated resonant cavity structure based on QBIC is designed and fabricated. The process of excitation of the QBIC mode is verified and the structural parameters are optimized after considering the ohmic loss by simulations. The simulated refractive index sensitivity of the sensor is up to 544 GHz/RIU, much higher than those of recently reported THz metamaterial sensors. Sensing sensitivity of the proposed metamaterial sensor is confirmed in experiment by detecting low-concentration lithium citrate (LC) and bovine serum albumin (BSA) solutions. The limits of detection (LoDs) are obtained to be 0.0025 mg/mL (12 μM) for LC and 0.03125 mg/mL (0.47 μM) for BSA, respectively, both of which excel over most of reported results in previous studies. These results indicate that the proposed THz metamaterial sensor has excellent sensing performances and can well be applied to the detection of low concentration biological samples.

With a reduction in the mortality rate of burn patients, patient length of stay (LOS) is increasingly adopted as an outcome measure. Some studies have attempted to identify factors that explain a burn patient's expected LOS. However, few have investigated the association between LOS and a patient's mental and socioeconomic status. There is anecdotal evidence for links between these factors and uncovering these will aid in better addressing the specific physical and emotional needs of burn patients, and facilitate the planning of scarce hospital resources. Here, we employ machine learning (clustering) and statistical models (regression) to investigate whether a segmentation by socioeconomic/mental status can improve the performance and interpretability of an upstream predictive model, relative to a unitary model derived for the full adult population of patients. Although we found no significant difference in the performance of the unitary model and segment-specific models, the interpretation of the segment-specific models reveals a reduced impact of burn severity in LOS prediction with increasing adverse socioeconomic and mental status. Furthermore, the models for the socioeconomic segments highlight an increased influence of living circumstances and source of injury on LOS. These findings suggest that, in addition to ensuring that the physical needs of patients are met, management of their mental status is crucial for delivering an effective care plan.

Recent astronomical observations with respect to measurements in distant supernovas, cosmic microwave background and weak gravitational lensing confirm that the Universe is undergoing a phase of accelerated expansion and it has been proposed that this cosmological behavior is caused by a hypothetical dark energy which has a strong negative pressure that allows explain the expanding universe. Several theoretical ideas and models related dark the energy includes the cosmological constant, quintessence, Chaplygin gas, braneworld and tachyonic scalar fields. In this paper, we have obtained new relativistic stellar configurations considering an anisotropic fluid distribution with a charge distribution which could represents a potential model of a dark energy star. In order to investigate the effect of a quadratic equation of state in this anisotropic model we specify particular forms for the gravitational potential that allow solving the Einstein-Maxwell field equations. For these new solutions we checked that the radial pressure, metric coefficients, energy density, anisotropy factor, charge density , mass function are well defined and are regular in the interior of the star. The solutions found can be used in the development of dark energy stars models satisfying all physical acceptability conditions but the causality condition and strong energy condition are violated. We expect that these models have multiple applications in astrophysics and cosmology.

Synthetic chalcomenite-type cupric selenite CuSeO₃∙2H₂O has been studied at room temperature under compression up to pressures of 8 GPa by means of single-crystal X-ray diffraction, Raman spectroscopy, and density-functional theory. According to X-ray diffraction, the orthorhombic phase undergoes an isostructural phase transition at 4.0(5) GPa with the thermodynamic character being first-order. This conclusion is supported by Raman spectroscopy studies which have detected the phase transition at 4.5(2) GPa and by the first-principles computing simulations. The structure solution at different pressures has provided information on the change with pressure of unit-cell parameters as well as on the bond and polyhedral compressibility. A Birch-Murnaghan equation of state has been fitted to the unit-cell volume data. We found that chalcomenite is highly compressible with a bulk modulus of 42 – 49 GPa. The possible mechanism driving changes in the crystal structure is discussed, being the behavior of CuSeO₃∙2H₂O mainly dominated by the large compressibility of the coordination polyhedron of Cu. On top of that, an assignation of Raman modes is proposed based upon density-functional theory and the pressure dependence of Raman modes discussed. Finally, the pressure dependence of phonon frequencies is also reported.

Zeta potential refers to the electrokinetic potential present in colloidal systems, exerting significant influence on the diverse properties of nano-drug delivery systems. The impact of dielectric constant on the zeta potential and charge inversion of highly charged colloidal particles, immersed in a variety of solvents spanning from polar, such as water, to nonpolar solvents, and in the presence of multivalent salts, was investigated through primitive model Monte Carlo (MC) simulations. Zeta potential ξ is decreased as decreasing the dielectric constant of the solvent, and upon further increase in the salinity and the valency of the salt. At elevated levels of salt, the colloidal particles become overcharged, in all solvents. As a result, their apparent charge becomes opposite in sign to the stoichiometric charge. This reversal of charge intensifies until reaching a saturation point with further increase in salinity, as a result, their apparent charge becomes opposite in sign to the stoichiometric charge. This reversal of charge intensifies until reaching a saturation point with further increase in salinity.

Topologically non-trivial magnetization configurations in ferromagnetic materials on the nanoscale, such as hopfions, skyrmions, vortices, etc., attract considerable attention of researchers during the last years. In this article applying the theory of micromagnetism, I demonstrate that the toroidal hopfion magnetization configuration is a metastable state of a thick cylindrical ferromagnetic nanodot or a nanowire of a finite radius. Existence of this state is a result of the competition of the exchange, magnetostatic, and magnetic anisotropy energies. The Dzyaloshinskyi-Moriya exchange interaction and surface magnetic anisotropy are of the second importance for the hopfion stabilization. The toroidal hopfion metastable magnetization configuration may be reached in the process of the sample re-magnetizing by applying an external magnetic field along the cylindrical axis.

A significant replacement for numerous fossil fuels is solar energy as the main type of renewable energy resource. However, solar cells need battery energy storage units to handle the intermittent and uncontrollable nature of solar energy. In this light, there is a significant market for small, portable battery charge controllers that automate battery charging. However, the issue of slow charging and premature battery life loss plagues current industry-standard or innovative battery technology. This study proposes a quick pulse charging technique that stops battery deterioration and minimizes the overall charging period. The primary goal of this study is to develop, construct, and execution of a practical, versatile, and compact photovoltaic charge controller at cut rates. The suggested charge controller can disconnect and reconnect the battery during battery overcharging and deep discharging conditions using sensors with relays. The laboratory model is tested using a less expensive PV panel, battery, and DSP controller. The charging behavior of the solar-powered PWM charge controller is studied compared to that of the Constant Voltage - Constant Current (CV-CC) method. The proposed method is pertinent for minimizing energy issues in impoverished placesat a reasonable price.

Nowadays, with the development of laser weapons, the primary power supply of laser weapons puts forward more and more high demand for its performance. The pulsed power supply based on conventional homopolar inductor alternator (HIA) cannot meet the requirements any more. In order to improve the power density and efficiency, this paper proposes applying the high-temperature superconducting (HTS) HIA with slotless stator core to this power supply. In this paper, the design considerations of it are presented, and the comparisons between the two power supplies are discussed. The calculation results show that the power supply based on HTS machine has much larger power density than the conventional HIA, and the efficiency is also larger than the conventional HIA. This can improve the performance of laser weapons dramatically.

The phenomena of electrical conductivity and electromigration in metallic systems are related, since in both cases the basic physical process is the scattering of conduction electrons by metal ions. Numerous searches have been made for equations connecting the conductivity with electromigration. In the case of a liquid metal, when using the Drude-Sommerfeld (DS) conduc-tivity equation, it was not possible to obtain a quantitative relationship between these phenomena, which would be correct. Attempts to find such a relationship when taking into ac-count the N. Mott correction (g - factor) in the DS equation were unsuccessful. This article proposes a different correction (b - factor) to the DS equation, which takes into account the pos-sibility of varying the momentum transferred by the conduction electron to a metal ion during the scattering. This correction allows to establish a quantitative relationship between conductivity and electromigration, as well as between electromigration in various binary systems with common components, in agreement with experiment. The proposed theory describes well, in particular, two- and multi-component metal systems of any concentration (the consistency rule for triangles A-B, B-C, C-A). The value of b - factor smoothly changes depending on the heat of vaporization of the metal, per unit volume.

Luminophores featuring thermally activated delayed fluorescence (TADF luminophores) are the workhorse of the third- and fourth-generation OLEDs. While these compounds had usually been used as dopants embedded in the host, non-doped TADF OLEDs have recently shown significant progress as well reaching the performance comparable to the host-dopant ones. For efficient operation of the non-doped OLEDs, charge transport in neat films and single crystals of TADF luminophores is important; however, this issue was nearly unexplored theoretically. In the current study, we calculated charge mobilities in four TADF single crystals, which have different molecular packing motifs. Specifically, in one of them both donor and acceptor moieties form uniform π-stacks, while in the others donors (acceptors) show alternating lateral shifts along the stacks; the difference in molecular packing results in the difference of transfer integral between the molecules. Reorganization energies differ as well up to four times for the studied crystals. As a result, charge mobilities vary from 0.001 to ~0.3 cm2/(V∙s), the largest being predicted for the crystal of the luminophore consisting of rigid donor and acceptor. We anticipate that the results obtained can be useful for the design of TADF luminophores for non-doped OLEDs, OLETs and other organic light-emitting devices.

A model for the simulation of ion beam extraction from an electron cyclotron resonance ion source is proposed. It is based on the simple fact that charged particles follow magnetic field lines. Therefore magnetic field lines are used to generate initial conditions for ray-tracing. This model reproduces in simulation experimentally obtained results. The importance of correlations in phase-space caused by the magnetic field is shown in simulation. This model also describes the physics of space-charge and its compensation in the extracted (fast) ion beam by low energy electrons. Simulation provides the possibility to test theoretical assumptions, as well as to optimize technical designs.

Although there is a common physiological notion that the origin of the membrane potential is attributed to transmembrane ion transport, it is theoretically possible to explain its generation by the mechanism of ion adsorption. It was previously suggested that the ion adsorption mechanism led even to the potential formulas which are even identical to either the famous Nernst equation or Goldman-Hodgkin-Katz equation. Our further analysis shown in this paper indicates that the potential formula based on the ion adsorption mechanism leads to one equation which is the function of material surface charge density and the material surface potential. Furthermore, we confirmed that the equation holds in all the different experimental systems we studied. Although we have not succeeded in elucidating why such an equation is established, the equation appears to be the key equation governing the characteristics of the membrane potential regardless of the systems in question.

4-component relativistic atomic and molecular calculations are typically performed within the no-pair approximation where negative-energy solutions are discarded, hence the symmetry between electronic and positronic solutions is not considered. These states are however needed in QED calculations, where furthermore charge conjugation symmetry becomes an issue. In this work we shall discuss the realization of charge conjugation symmetry of the Dirac equation in a central field within the finite basis approximation. Three schemes for basis set construction are considered: restricted, inverse and dual kinetic balance. We find that charge conjugation symmetry can be realized within the restricted and inverse kinetic balance prescriptions, but only with a special form of basis functions that does not obey the right boundary conditions of the radial wavefunctions. The dual kinetic balance prescription is on the other hand compatible with charge conjugation symmetry without restricting the form of the radial basis functions. However, since charge conjugation relates solutions of opposite value of the quantum number κ, this requires the use of basis sets chosen according to total angular momentum j rather than orbital angular momentum ` . As a special case, we consider the free-particle Dirac equation, where the solutions of opposite sign of energy are related by charge conjugation symmetry. We note that there is additional symmetry in those solutions of the same value of κ come in pairs of opposite energy.

This Letter revisits the instability of jet produced by shaped charge. Scaling laws for shaped charge jet are derived by dimensional analysis. It shows that the scaling laws are universal when cross-sectional shrinkage rate is not included in the formulation.

Structural perturbations in the Mn4CaO5 cluster site, an oxygen-evolving complex of photosystem II, such as those induced by Ca2+/Sr2+ exchanges or Ca/Mn-removal have been known to induce long-range positive shifts (+30 mV to +150 mV) in the redox potential of the primary quinone electron acceptor plastoquinone A (QA) located 40 Å distant from the OEC. Here, we reanalyzed the crystal structure of Sr-PSII solved at 2.1 Å and compare it with the native Ca-PSII of 1.9 Å with focus on the acceptor site and report on the possible long-range interactions between the donor, Mn4Ca(Sr)O5 cluster, and acceptor sites.

The experiments of Project 8 have been excellent, but the expected goals still difficult to achieve. So much so that some of the results at your fingertips were also missing. In view of this, the focus of this article is to clarify several easy confused concepts. Only in this way, we can reasonably explain the experimental data. The main points are as follows: 1. The value c of the light speed in vacuum and a particle with zero static mass, both of which do not exist in the reality. That is to say, the so-called a photon's static mass is equal to zero but has energy, which is a paradox that confuses two different definitional domains. 2. In the reality, photons are high-speed particles generated by electromagnetic radiation. They must have the characteristics of (static) mass, energy and wave, in order to describe the main body to aim at photons from different angles. 3. After any main body comes into being electromagnetic radiation, its static mass will inevitably decrease accordingly. 4. The charge-mass ratio of an electron is a physical constant, which is the ratio of its charge to the amount of matter, and is not affected by relativistic effects and electromagnetic radiation. 5. The uncertainty of moving electrons is caused by random electromagnetic radiations. Finally, it is pointed out that if the cyclotron frequency of a single electron is measured, and at the same time, its de Broglie wavelength or frequency can also be measured, then its static mass can be obtained. Even so, the expected goals are still difficult to achieve, because random electromagnetic radiations are always taking away continually the matter composition of the single electron being measured. However, this was precisely a result of the research obtained by Project 8, and had universality, which should be reflect on.

Diaminomaleonitrile (DAMN) is an electron-rich ligand which is commonly used in the synthesis of purines, amides and Schiff base ligands. In the last case lies the interest in this molecule, given its symmetry and apparent facility to form various ligands and complexes of interest in fields such as organic solar cells and catalysis among others. Nevertheless, its bisubstitution with aldehydes displays certain difficulty due to the double conjugated presence of the nitrile group (C≡N) in its structure, which significantly affect its coordination behavior by modulating the chemical reactivity of its amines. In addition to presenting a practical resume of guidelines for the preparation of different bisubstituted compounds from DAMN, this paper reviews the possibility of attaining a precise characterization by simple spectroscopic techniques. We provide an additional discussion for one of these techniques (commonly reported but often overlooked), given its potential to provide both the symmetry and E/Z configuration of the product. We hope the comprehensive evidence discussed and shown in this review will be helpful to further develop and understand the products derived of this interesting molecule in their broad applications.

In this study, a numerical simulation of fluid flow through railway ballast in the time domain is presented, providing a model for unsteady-state flow. It is demonstrated that the position of the free surface with respect to time can also be used to solve the steady flow case. The effect of ballast fouling is included in the model to capture the realistic behavior of railway ballast, which is critical to understanding the impact of flooding. A thorough comparison with a range of previous studies, including theoretical and experimental approaches, is made and very close agreement is obtained. The significant impact of ballast fouling on fluid flow and its potential consequences for railway infrastructure are highlighted by the simulation. Valuable insights into the behavior of water flow through porous media and its relevance to railway ballast management are offered by this study.

The redefined vacuum approach, which is frequently employed in the many-body perturbation theory, proved to be a powerful tool for formula derivation. Here, we elaborate this approach within the bound-state QED perturbation theory. In addition to general formulation, we consider the particular example of a single particle (electron or vacancy) excitation with respect to the redefined vacuum. Starting with simple one-electron QED diagrams, we deduce first- and second-order many-electron contributions: screened self-energy, screened vacuum polarization, one-photon exchange, and two-photon exchange. The redefined vacuum approach provides a straightforward and streamlined derivation and facilitates its application to any electronic configuration. Moreover, based on the gauge invariance of the one-electron diagrams, we can identify various gauge-invariant subsets within derived many-electron QED contributions.

This article examines the impact of some system parameters on an industrial system composed of two dissimilar parallel units with one repairman. The active unit may fail due to essential factors like aging or deteriorating, or exterior phenomena such as Poisson shocks that occur at various time periods. Whenever the value of a shock is larger than the specified threshold of the active unit, the active unit will fail. The article assumes that the repairman has the right to take any of two decisions at the beginning of the system operation: either a takes a vacation if the two units work in a normal way, or stay in the system to monitor the system until the first system failure. In case of having a failure in any of the two units during the absence of the repairman, the failing unit will have to wait until the repairman is called back to work. We suppose that the value of every shock is assumed to be i.i.d. with some known distribution. The length of the repairman’s vacation, repair time, and recall time are arbitrary distributions. Various reliability measures have been calculated by the supplementary variable technique and the Markov’s vector process theory. At last, numerical computation and graphical analysis have been given for a particular case to validate the derived indices.

This paper builds upon a theory of emerging-state actors using ISIS as a case study. This paper seeks to apply the theory in analyzing intervention & containment policies to use against emerging-state actors, using ISIS as the case study. Two baseline scenarios are used for evaluation – one replicating the historical foreign intervention against ISIS and a counter-factual where no foreign intervention occurred. Eleven contemporary military policies were tested against these baseline in isolation, combination, at different timing windows and under hypothetical “best case” conditions as well as operationally constrained. Insights of these tests include the influence of ethnographic envelopes, timing windows. Finally, a policy based on emerging-state actor theory is tested performing substantially better across primary measures than other policies or the historical baseline. This is compared against a falsified-policy designed to disprove that emerging-state actor theory contributed to the benefits. This paper’s contributions are a practical application of system dynamics simulations and systems-thinking to current problems, generate insights into the dynamics of emerging-state actors and intervention strategies, and demonstrate utility for future application of the underlying simulation in other scenarios involving non-state actor irregular conflict including terrorism, insurgents, or emerging-state actors.

Space-time evolution is briefly explained by using the 3-dimensional quantized space model (TQSM) based on the 4-dimensional (4-D) Euclidean space. The energy (mass), charges and absolute time are newly defined based on the 4-D Euclidean space. The photons and gravitons are understood as the 2-D space fluctuations along the space axes and 1-D time fluctuations along the time axis, respectively. This indicates that the electromagnetic (EM) and gravitational (G) waves can be unified into the so called gravityelectromagnetic (GEM) wave which has both space and time fluctuations. The photon with zero force fields is the 2EM wave because an EM wave corresponds to a charged fermion. The dark matter bosons, weak force bosons, strong force bosons are the 1-D time fluctuations which can be expressed by the G waves. This indicates that all five forces are unified by the GEM wave. It is called as the super unification theory in the present work. And the force carrying bosons and mesons are, for the first time, proposed as the possible candidates of the magnetic monopoles like the fermions and baryons are the electric monopoles. The signs of the magnetic charges quantized as q_m=cq are newly defined. The big bang is understood by the space-time evolution of the 4-D Euclidean space but not by the sudden 4-D Minkowski space-time creation. The big bang process created the matter universe with the positive energy and the partner anti-matter universe with the negative energy from the CPT symmetry.

Using the principle of equivalence, it has recently been shown that the electrostatic field lines of a charge, stationary in the gravitational field, bend exactly like the trajectories of photons emitted isotropically from a source at the charge location and that the fraction of electric flux crossing a surface `below' or `above' the charge is exactly similar to the fraction of photon trajectories intersecting these surfaces, with more flux in the downward direction than upward. As one goes much deeper in the gravitational field, all electric field lines increasingly point in the vertically downward direction as is also the case for a stream of photons. Since photon trajectories as well as electric field lines, at any location in the gravitational field, are affected by the local space-time curvature an inference can be drawn that this parallel between the photon trajectories and the electric field lines is a general result. We could then apply these results in the external gravitational field of a black hole, where the trajectories of photons in the gravitational field are already well-known and the behaviour of electric field lines of a stationary charge could be inferred therefrom. Accordingly, we show that the electric field through an external spherical surface surrounding the black hole steadily reduces as the charge location approaches the event horizon (Schwarzschild radius), and like photons from a source inside the Schwarzschild radius cannot escape outside, the electric field lines of a charge within the black hole too remain trapped inside the event horizon. From this one arrives at a conclusion that, contrary to the conventional wisdom, the electric charge contained inside a static black hole cannot be detected or inferred by an external observer. A black hole, said to have no hair with the only external identifying characteristics being mass, electric charge, and angular momentum, is therefore all the more `hairless', as even its charge cannot be ascertained. The derivation of the Reissner-Nordström metric, supposedly describing the gravitational field of a static charged black hole, presumes an external stress-energy tensor of the electrostatic field, as per Gauss law, even for the charges contained within the black hole. However, the absence of electric flux external to a static charged black hole implies that such a charged black hole is not described correctly by the Reissner-Nordström metric and the consequential peculiarities of the space-time geometry, leading in specific cases to the idea of a naked intrinsic singularity and a need for the ``cosmic censorship'' hypothesis, also do not arise here.

Quantum computing arrives. Preceded by Mādhava of Sangamagrāma and other Hindu mathematicians, around 1,500 CE, and our previous work, we show at least 4 quantum properties that are indeed universal in some number systems; here we use them to enable quantum computing. Using the sets B={0,1}, B^n, N, Z, Q, and Q*, one has +4 quantum properties that one can trust, as archetypes of easy communication to friends and foes, to ignoranti or cognoscenti, and for quantum consciousness. Therefore, this work applies to computer calculations, apps in cell phones, algebra, atoms, mathematics, physics, and the human mind.

We present a new vision on the double-slit experiment (DSE), that does not use any waves or the so-called wave-particle duality. It is based on particles, viewed as localized vibrations. Rather than being illogical, or mysterious, the approach reproduces logically the interference patterns observed externally, using the well-known ``amplification of stimulated emission'' (ASE). The conservation of particle number is not observed. Different particles can present ASE with in-phase or counter-phase behavior, making the patterns observed for electrons, other particles, even atoms. The Law of the Excluded Middle (LEM) is not broken illogically in two-states macroscopically, but broken naturally in three or more states, microscopically, using ASE. Any particle supporting ASE, in-phase or counter-phase, can enter a DSE, and provide an external interference pattern. Frequency plays a role, while amplitude is not considered. This work is important in quantum computing, possibly saving cost, time, and welcoming more participants.

It was recently studied how to achieve the optimal degrees of freedom (DoF) in a multi-antenna full-duplex system with partial channel state information (CSI). In this paper, we revisit the DoF of a multiple-antenna full-duplex system using opportunistic transmission under the partial CSI, in which a full-duplex base station having M transmit antennas and M receive antennas supports a set of half-duplex mobile stations (MSs) having a single antenna each. Assuming no self-interference, we present a new hybrid opportunistic scheduling method that achieves the optimal sum DoF under an improved user scaling law. It is shown that the optimal sum DoF of 2M is asymptotically achievable provided that the number of MSs scales faster than SNR^M, where SNR denotes the signal-to-noise ratio. This result reveals that in our full-duplex system, better performance on the user scaling law can be obtained without extra CSI, compared to the prior work that showed the required user scaling condition (i.e., the minimum number of MSs for guaranteeing the optimal DoF) of SNR^2M−1.

The primary goal of this review is to provide a comprehensive overview of the state-of-the-art in solid-state batteries (SSBs), with a focus on recent advancements in solid electrolytes and anodes. The paper begins with a background on the evolution from liquid electrolyte lithium-ion batteries to advanced SSBs, highlighting their enhanced safety and energy density. It addresses the increasing demand for efficient, safe energy storage in applications like electric vehicles and portable electronics. A major part of the paper analyzes solid electrolytes, key to SSB technology. It classifies solid electrolytes as polymer-based, oxide-based, and sulfide-based, discussing their distinct properties and application suitability. The review also covers advancements in anode materials for SSBs, exploring materials like lithium metal, silicon, and intermetallic compounds, focusing on their capacity, durability, and compatibility with solid electrolytes. It addresses challenges in integrating these anode materials, like interface stability and lithium dendrite growth. This review includes a discussion on the latest analytical techniques, experimental studies, and computational models to understand and improve the anode-solid electrolyte interface. These are crucial for tackling interfacial resistance and ensuring SSBs' long-term stability and efficiency. Concluding, the paper suggests future research and development directions, highlighting SSBs' potential in revolutionizing energy storage technologies. This review serves as a vital resource for academics, researchers, and industry professionals in advanced battery technology development. It offers a detailed overview of materials and technologies shaping SSBs' future, providing insights into current challenges and potential solutions in this rapidly evolving field.

The species composition of vultures and their interactions on carcasses of various stages of decomposition is not well understood yet it potentially affects their food acquisition and survival. We collected data from six carcasses between June and December 2021 using camera traps that were set on carcasses undergoing various decomposition states in Sinamatella Camp of Hwange National Park, Zimbabwe. Of interest were the cases in which each vulture species was dominating in interactions which gave it an advantage in terms of food acquisition. Four vulture species were observed (White-backed, White-headed, Lappet-faced and Hooded Vultures). Vulture abundances were greatest on fresh carcasses and least on dry ones. Although dominance behaviors by the White-backed and White-headed Vultures were recorded over all other vulture species, there were no records of the Lappet-faced dominating other vultures. In addition, the Hooded Vultures were mostly dominating non-vulture avian species on advanced decay carcasses. Our results demonstrate how various species may be prone to intense competition that may further place them at disadvantageous positions if food sources decline, more so under climatic shifts and various anthropogenic pressures.

The concept of “hyperferritinemic syndrome” defines a complex pathophysiological and clinical entity, characterized by a systemic hyperinflammatory state, generally associated with elevated levels of proinflammatory cytokines (hypercytokinemia) and high serum levels of ferritin (hyperferritinemia), traditionally recognized as an iron-binding plasma protein involved in the storage of iron in a biologically available form for different physiological cellular processes. Recent studies have shown that ferritin has other important functions as well, operating both as a proinflammatory mediator and as a immunosupressive agent, its elevated levels in the serum being detected in various conditions associated with inflammatory states, such as infectious diseases, autoimmune and autoinflammatory disorders and, in some cases, in malignancies. Catastrophic antiphospholipid syndrome (cAPS), systemic juvenile idiopathic arthritis (sJIA) and adult-onset Still’s disease (AOSD) and acquired forms of hemophagocytic lymphohistiocytosis (HLH), which includes macrophage activation syndrome (MAS), have been associated with hyperinflammatory states and dramatic elevations of serum ferritin, generating hyperferritinemic syndromes. Severe forms of coronavirus disease-2019 (COVID-19), in which MAS may frequently develop, has also been linked to the development of a hyperferritinemic syndrome. This review offers several insights into the physiological and pathophysiological roles of ferritin in several (hyper-)inflammatory diseases, but also into the causal entities, the underlying pathophysiological mechanisms, clinical manifestations and diagnostic features of somewhat obscure, yet potentially fatal pathological conditions, reunited under the concept of hyperferritinemic syndromes.

The validity of our universe as a three-dimensional space (3+1 in relativity) is considered a fundamental fact in physics. In this study, we show that our observed world is thus the output of a prior fundamental operator referred to as an organizer. The organizer is an expansion of projecting operators. It is been shown that identical weighted projecting operators, which are associated with identical particles, generate subspaces of entangled states, whereas groups of unequal weighted coefficients are responsible for finite-size subspaces that are associated with unidentical particles. Considering 3D-subspaces as evidence of the coefficients’ arrangement in our universe, we implement our formalism to describe the implacable vectors, location, momentum, and force within each 3D subspace. By implementing the Heisenberg relation, we drive both the classical and quantum expressions for the laws of motion.

Quantum mechanics introduces the concept of an observer who selects a measuring device and reads the outputs. This measurement process is irreversible. Lately, scholars on quantum collapse phenomena have presented a quantum-like formalism describing the measurement results as an interpretation of the measured object. Note that an observer must read the interpretation results after the interpretation process. Therefore, we propose that the definition of the concept of life should be expanded based on the following concept: A living system decreases entropy, measured results are interpreted, and an internal observer reads the commentary.

Mathematical models across the applied sciences often utilize a standard methodological representation called a state variable formulation more commonly referred to as state space form. Recent research in unmanned underwater vehicle motor turbine blade thermal modeling for fatigue-life is generalized here permitting the proposed novel state space from to be applied to electrodynamics, motion mechanics, and many other disciplines. Proposed here is a very compact form inherently representing time variance, with a convenient presentation of dynamic variables applicable to all proper transfer functions, where all the distinct, real poles, zeros and gain of the transfer function appear as explicit components in the state space. The resulting manifestation simplifies utilization of the state space methods broadly across the applied sciences.

Schizophrenia is widely seen as a disorder of dysconnectivity. Neuroimaging studies have examined both structural and functional connectivity in the disorder, but these modalities have rarely been integrated directly. We scanned 29 patients with schizophrenia and 25 healthy control subjects and acquired resting state fMRI and diffusion tensor imaging. The Functional and Tractographic Connectivity Analysis Toolbox (FATCAT) was used to estimate functional and structural connectivity of the default mode network. Correlations between modalities were investigated, and multimodal connectivity scores (MCS) were created using principal components analysis. Nine of 28 possible region pairs showed consistent (>80%) tracts across participants. Correlations between modalities were found among those with schizophrenia for the prefrontal cortex, posterior cingulate, and lateral temporal lobes with frontal and parietal regions, consistent with frontotemporoparietal network involvement in the disorder. In patients, MCS values correlated with several aspects of the Positive and Negative Syndrome Scale, positively with those involving inwardly directed psychopathology, and negatively with those involving external psychopathology. In this preliminary sample, we found FATCAT to be a useful toolbox to directly integrate and examine connectivity between imaging modalities. A consideration of conjoint structural and functional connectivity can provide important information about the network mechanisms of schizophrenia.

Analytical solutions for radiation dominated phase of Quasi Steady State Cosmology in Friedmann-Robertson-Walkar models are obtained. We find that matter density is positive in all the cases (k = 0,-1,1). The nature of Hubble parameter (H) in [0,2] is discussed. The deceleration parameter (q) is marginally less than zero indicating accelerating universe. The scale factor (S) is graphically shown with time. The model represents oscillating universe between the above mentioned limits. Because of bounce in QSSC, the maximum density phase is still matter dominated. The models represent singularity free model. We also find that the models have event horizon i.e. no observer beyond the proper distance rH can communicate each other in FRW mdels for radiation dominated phase in the frame work of QSSC. The FRW models are special classes of Bianchi type I, V, IX space-times with zero, negative and positive curvatures respectively. Initially i.e. at  = 0, the model represents steady model. We have tried to show how a good fit can be obtained to the observations in the framework of QSSC during radiation dominated phase.

The principal aim of a spectral observer is twofold: the reconstruction of a signal of time via state estimation and the decomposition of such a signal into the frequencies that make it up. A spectral observer can be catalogued as an online algorithm for time-frequency analysis because is a method that can compute on the fly the Fourier transform (FT) of a signal, without having the entire signal available from the start. In this regard, this paper presents a novel spectral observer with an adjustable constant gain for reconstructing a given signal by means of the recursive identification of the coefficients of a Fourier series. The reconstruction or estimation of a signal in the context of this work means to find the coefficients of a linear combination of sines a cosines that fits a signal such that it can be reproduced. The design procedure of the spectral observer is presented along with the following applications: (1) the reconstruction of a simple periodical signal, (2) the approximation of both a square and a triangular signal, (3) the edge detection in signals by using the Fourier coefficients, (4) the fitting of the historical Bitcoin market data from 2014-12-01 to 2018-01-08 and (5) the estimation of a input force acting upon a Duffing oscillator. To round out this paper, we present a detailed discussion about the results of the applications as well as a comparative analysis of the proposed spectral observer vis-à-vis the Short Time Fourier Transform (STFT), which is a well-known method for time-frequency analysis.

Changing the symmetry of spin from SU(2) to the quaternion group, $Q_8$, has many ramifications. In this paper we first summarize the properties of Q-spin and then discuss some of those resulting changes.

Conical emission is a typical nonlinear phenomenon that occurs when the femtosecond laser pulses interact with transparent media. In this work, the conical emission induced by two kinds of typical vortex beams (i.e., Laguerre-Gaussian (LG) and Bessel-Gaussian (BG) beams) in water is experimentally studied. By recording the light spots of different wavelengths on the screen, the characteristics of the conical emission induced by femtosecond vortex beams are studied. It is found that the spots of the supercontinuum induced by the two kinds of vortex beams differ greatly from each other: The spots of the supercontinuum induced by the BG beam are a set of concentric rings like a rainbow with a white center, while the whit light spot in the case of the LG beam are a circular white disk, which is different from the commonly observed white light spots. By measuring the maximum divergence angle, it is observed that the divergence angle increases with the decrease of the wavelength, while the TC merely affects the divergence angle, which is explained from the formation mechanism of conical emission in terms of self-phase modulation. We hope this work can be helpful to the understanding of interaction between the intense laser pulses and matters.

We have detected a large Nernst effect in the CDW state of the multiband organic metal α−(BEDT−TT)2KHg(SCN)4. We find that there exists a significant gradient of charge relaxation processes that can generate a sizeable contribution adding especially to the transverse thermoelectric signal. Apart from the phonon drag, the energy relaxation processes governing the electron-phonon interactions and the momentum relaxation processes governing the charge mobility of the q1D group of carriers have a significant role in observing the large Nernst signal in the CDW state. The emphasised momentum relaxation dynamics in the low field CDW state is a clear indicator of a significant carrier mobility that can lead to the largest Nernst signal in this state. The momentum relaxation is reduced with increasing angle and magnetic field, i.e., in the high field CDW state which is reflected in the smaller Nernst effect amplitude. In this case only the phonon drag and electron-phonon interactions are contributing to the transverse thermoelectric signal. Our findings advance and change the previous observations on the complex properties of this organic metal.

Anyon is collective excitation of two dimensional electron gas subjected to strong magnetic field, carrying fractional charges and exotic statistical character beyond fermion and boson. So far, anyons with serial fractional charges only exist in fractional quantum Hall effect. It is still a challenge to find new serial of fractional charges in other physical system and develop an unified mathematical physics theory based on the same root. Here a topological path fusion theory of propagating electrons in magnetic flux lattice is proposed to explore the physical origin of fractional charges based on a generalization of Feynman's path integral theory and Thurston's train track theory. This mathematical physics theory generated the existed serial of fractional charges in fractional quantum Hall effect and predicted new serial of fractional charges. A serial of irrational charges are predicted in one dimensional lattice of magnetic fluxes. Fractionally charged anyons are also generated in two dimensional and three dimensional lattice of train tracks of electric currents, revealing an exact correspondence between knot lattice model and train track model. A new explanation for the modular symmetry of complex Hall conductance and composite fermion in fractional quantum Hall effect is also derived from this topological path fusion theory. Experimental observation of anyon in three dimensions can be realized by constructing three dimensional interlocking magnetic fluxes or mapping magnetic fluxes into forbidden zones in multi-connected space filled by solid state material. A photonic crystal with porous nano-structures is a promising system for detecting fractional charges and paves a new way for topological quantum computation.

Abstract The construction of a heterostructured nanowire array allows the manipulation of the interfacial, surface, charge transport, and transfer properties simultaneously, offering new opportunities to achieve multi-functionality for various applications. Herein, we developed a facile thermal evaporation and post-annealing method to synthesize ternary-Zn2SnO4/binary-ZnO radially heterostructured nanowire arrays (HNA). Vertically aligned ZnO nanowire arrays (3.5 μm in length) were grown on a ZnO-nanoparticle-seeded fluorine-doped tin oxide substrate by a hydrothermal method. Subsequently, the amorphous layer consisting of Zn-Sn-O complex was uniformly deposited on the surface of the ZnO nanowires via the thermal evaporation of the Zn and Sn powder mixture in vacuum, followed by post-annealing at 550 °C in air to oxidize and crystallize the Zn2SnO4 shell layer. The use of a powder mixture composed of elemental Zn and Sn (rather than oxides and carbon mixture) as an evaporation source ensures high vapor pressure at a low temperature (e.g., 700 °C) during thermal evaporation. The morphology, microstructure, and charge-transport properties of the Zn2SnO4/ZnO HNA were investigated by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, transmission electron microscopy, and electrochemical impedance spectroscopy. Notably, the optimally synthesized Zn2SnO4/ZnO HNA shows an intimate interface, high surface roughness, and superior charge-separation and -transport properties compared with the pristine ZnO nanowire array.

According to observations leptons are always produced in pairs. Both particles can be electrically charged, or just one, in which case the charged particle is accompanied by a particle specific neutrino. The period doubling process in nonlinear dynamical systems creates stable pair structures from the Planck units. The electron-positron pair is one of the stable structures, and the rest mass, electric charge and magnetic moment can be accurately calculated by the period doubling process. That the pair structure is stable means, that e.g., an electron and a positron are always born together. In the muon decay one of the pair is charged, while the other remains chargeless because there is only one charge available. It is suggested in this article that neutrino is the chargeless part of the lepton pair.

Corona loss generated from conductors is one of the important design factors on ac transmission lines. Based on helical charge simulation method, the 3-D corona loss calculation model considering the conductors’ outer strands in the corona cage is established. With regard to 2-D corona-loss calculation method, the calculation model proposed in this paper can take the electric field strength’s nonuniformity along the axial direction of stranded conductor into consideration, furthermore, it can also calculate the corona loss when the conductor has sag. The calculation results of the LGJ-300/40 and LGJ-400/35 in the small corona cage well coincide with the measurement results, which indicates that the corona-loss calculation model is appropriate. In addition, the corona loss of the bundle conductors 4 × LGJ720 with sag in UHV corona cage is also analyzed.

This work addresses the role of charge regulation (CR) and the associated fluctuations in the conformational and mechanical properties of weak polyelectrolytes. Due to CR, changes in the pH-value modifies the average macromolecular charge and conformational equilibria. A second effect is that, for a given average charge per site, fluctuations can alter the intensity of the interactions by means of correlation between binding sites. We investigate both effects by means of Monte Carlo simulations at constant pH-value, so that the charge is a fluctuating quantity. Once the average charge per site is available, we turn off the fluctuations by assigning the same average charge to every site. A constant charge MC simulation is then performed. We make use of a model which accounts for the main fundamental aspects of a linear flexible polyelectrolyte i.e. proton binding, angle internal rotation, bond stretching and bending. Steric excluded volume and differentiated treatment for short-range and long-range interactions are also included in the model. It can be regarded as a kind of "minimal'' model in the sense that contains a minimum number of parameters but still preserving the atomistic detail. It is shown that, if fluctuations are activated, gauche state bond probabilities increase, and the persistence length decreases, so that the polymer becomes more folded. Macromolecular stretching is also analyzed in presence of CR (the charge depends on the applied force) and without CR (the charge is fixed to the value at zero force). The analysis of the low force scaling behavior concludes that Pincus exponent becomes pH-dependent. Both with and without CR, a transition from 1/2 at high pH-values (phantom chain) to 3/5 to low pH-values (Pincus regime), is observed. Finally, the intermediate force stretching regime is investigated. It is found that CR induces a moderate influence in the force-extension curves and persistence length (which in this force regime becomes force-dependent). It is thus concluded that the effect of CR on the stretching curves is mainly due to changes in the average charge at zero force. It is also found that, for the cases studied, the effect of steric excluded volume is almost irrelevant compared to electrostatic interactions.

End-of-life electric vehicle (EV) batteries can be reused to reduce their environmental impact and economic costs. However, the growth of a second-life market is limited by the lack of information on the characteristics and performance of these batteries. As the volume of end-of-life EVs may exceed the amount of batteries needed for stationary applications, investigating the possibility of repurposing them in mobile applications is also necessary. This article presents an experimental test that can be used to collect the data necessary to fill a battery passport. The proposed procedure can facilitate the decision making process regarding the suitability of a battery for reuse at the end of its first life. Once the battery passport has been completed, the performance and characteristics of the battery are compared with the requirements of several mobile applications. Mobile charging stations and forklift trucks were identified as relevant applications for the reuse of high capacity prismatic cells. Finally, a definition of a state of health (SoH) is proposed to track the suitability of the battery during use in the second life application considering not only energy but also power and efficiency of the battery. This SoH shows that even taking into account accelerated ageing data, a repurposed battery can have an extended life of 11 years at 25~°C. It has also been shown that energy fade is the most limiting performance for lifetime and that cell-to-cell variation should be tracked as it has been shown to have a significant impact on battery life.

The purpose of this study is to examine the relationship between the institutional investors which can affect financial performance for corporate sustainability on the income smoothing. Therefore, this study focus on the connection between the nature of stock rights and income smoothing in China. For this study, hypotheses were established on the relationship each state-controlled companies, income smoothing, and information equilibrium of individual investors, and empirical analysis was conducted through related variables. The analysis results are summarized in three categories as follows. First, this research finds that state-controlled firms (CONTs) prefer income smoothing activities compared to non-state-controlled firms for the long-term sustainable development of firms using data from 2011 to 2019. Second, this study found out that Institutional investors support the behavior of CONTs to smooth their earnings because this behavior is seen as an attempt by CONTs to convey valuable private information to other investors. Third, we was able to discover that institutional investors' monitoring effect is predominantly driven by pressure-resistant institutional investors. This research complements the lack of empirical research on income smoothing and enable to give a guideline that the type of stock rights is a critical key determinant of participation in income smoothing activities for stable growth and sustainability in the future.

A unified critical state model has been developed for both clean sand and silty sand using the modified Cam-clay model (MCC). The main feature of the proposed model is a new critical state line equation in the e-ln(p) plane that is capable of handling both straight and curved test results. With this feature, the error in calculating plastic volumetric strain is eliminated in theory. Another crucial feature of the model is the transformed stress tensor based on the SMP (spatially mobilized plane) criterion, which takes into account the proper shear yield and failure of soil under three-dimensional stresses. Additionally, the proposed model applies the intergranular void ratio with the fines influence factor for silty sand. Only eight soil parameters are required for clean sand, and a total number of twelve soil parameters are needed for silty sand.

Considering the negative impacts of climate changes along with the rapid increase in population in Islamic dominated states, e.g., the Middle East, water tension among upstream and downstream states is increasing. Despite the importance of water management in Islamic culture, the role of religion has been under-valued and under-emphasized by the scholars. The paper has sought to compare and contrast Islamic water management principles (IWMP) with international water law principles (IWLP). The findings from this analysis show not only that IWMP are in conformity with IWLP, but that in many cases, IWMP can be more effective. For instance, where international water accords between riparian states of a shared river basin are poorly developed and lack enforcement mechanisms under IWLP, those upstream states can abuse their geographical locations depriving those downstream-ers. In contrast, IWMPs stress the equitable and reasonable use of water resources among upstream and downstream users of a shared watercourse. Moreover, although IWLPs emphasize the conservation and preservation of ecosystems and the environment at the basin level, the inter-basin states especially those upstream can pose significant harm to the ecosystems. On the other side, Islam as the religion of peace, has placed much emphasis on the preservation of nature. For example, the verse, “.... And waste not by excess, for Allah loves not the wasters” [Quran, 7:31], illustrates the importance of the sustainable use of water and the environment. It is argued that if Islamic Water Management Principles are incorporated into the management instrument of Islamic States, the issue of equitable and sustainable use of water among Muslim-dominated riparian states (e.g., Iran, Afghanistan, etc.) will be solved.

This paper seeks to explain the rapid growth of the Islamic State of Iraq & Syria (ISIS) and approach the question of “what is” the Islamic State? The paper offers several contributions. First is the proposal of a dynamic hypothesis that ISIS is an emerging-state actor and differs notably from traditional non-state actors and insurgencies. The theory consists of both a causal loop diagram and key propositions. A detailed system dynamics simulation (E-SAM) was constructed to test the theory. The propositions of emerging-state actor theory are constructed as synthetic experiments within the simulation and confirm evidence of emerging-state actor behavior. E-SAM’s novelty is its combination of combat simulation with endogenous geospatial feedback, ethnographic behavior in choosing sides in conflict, and details internal simulation of key actor mechanisms such as financing, recruiting and governance. E-SAM can be loaded with scenarios to simulate non-state actors in different geospatial domains: ISIS in Libya, Boko Haram in Nigeria, Taliban in Afghanistan and even expatriated ISIS fighters returning to pursue new conflicts such as in Indonesia.

This paper describes an entropy equation that can be used for measuring energy. It originated from measuring economy in AI models, where the assumption would be that any organic system makes use of energy efficiency to form its structures. Looking at clustering and cohesion resulted in the equation E = (mean * variance). It was apparent however, that it was a very generic type of equation and it could be adjusted so that distance represents mean. This new version was applied to the domain of physics and the universe, when the equation can support the idea that work is done through the energy released by the 'change' in entropy. A comparison with Einstein's relativity equation is made and also the audacious suggestion that a black hole has only potential energy inside, which converts to kinetic energy after a Big Bang, for example. From that suggestion, a universal theory about state change can be made.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Partially state-owned firms are common in both developed and developing countries and contribute around 10% of the world's GDP. This has led to a rich literature exploring various aspects of competition between such “mixed”-ownership firms. This paper contributes to the existing literature by studying the effects of mixed ownership on the intensity of competition in oligopoly markets. Our findings indicate that state ownership exerts an anti-competitive influence, with a higher state ownership share resulting in less aggressive behavior by firms in the product market. This result implies that industries with a higher proportion of state ownership yield lower total surplus. Further, when considering factors such as taxes, soft budget constraints, and weak property rights, the anti-competitive effects of state ownership are accentuated.

In recent times, there has been significant enthusiasm for the development of all solid state batteries. This interest stems from a dual focus on safety—addressing concerns related to toxic and flammable organic liquid electrolytes—and the pursuit of high energy density. \cite{SCHNELL2018160,Zheng2018}. While liquid electrolyte batteries constitute for now the vast majority of commercial cells, solid electrolyte batteries show great promise. In parallel with experimental research, computational models \cite{GrazioliEtAlCM2016} clarify the several fundamental physics \cite{LiMonroeARCBM2020} that take place throughout battery operations. We review some classical models, emphasizing the conceptual advancements documented in the most recent works.

Bridges enable communications and transportation of goods nationally and internationally, underpinning economic and social activities, thus they are pylons of our prosperity and mobility. Bridges worldwide are constantly subjected to physical wear, ageing, deterioration, hazards, environmental influences, and increased loading. Loss of performance and functionality of bridge structures would have a crucial impact on overall infrastructural resilience and would cause significant negative economic and social consequences. Monitoring their behaviour for different loading conditions relies on accurate estimations of the stress-strain state of various critical components and remaining capacities. These activities are of high importance for better planning lifespan prolongation, that is the extension of their service life and prevention of unforeseen collapses, in line with sustainability principles of well-informed maintenance. In many cases, access to the structure is limited or even impossible, which causes the need for the deployment of remote and contactless methods. One such innovative technique, which has recently attracted attention in scientific and practical applications is the digital image correlation (DIC). DIC is a contactless approach applicable for long-term measurements, which enables obtaining the full field of strains and deformations. Although the DIC approach has been widely used in world engineering practice for monitoring bridges and has proved to be a reliable and accurate method, there is a lack of systematic integral review on previous practical applications, revealing limitations and perspectives. This is the main motivation and novelty of this study, which will describe selected case studies, in which DIC was used on real full-scale bridge structures and propose improvements for the method.

This review provides an extensive overview of the developments in the field of polymer science, focusing on the solid-state modification (SSM) of thermoplastic materials. The background of the study places thermoplastics within the context of their increased use over the past century, highlighting their versatility in various applications and the associated environmental and health concerns due to certain additives. The methods section delves into the specifics of SSM, a technique that involves the incorporation of monomers or oligomers into the amorphous phase of polymers through multiple exchange reactions, distinguishing it from traditional melt polymer modification methods. The results section outlines the unique aspects of SSM and its increasing recognition for its potential to enhance material performance in areas such as catalysts and composites. It also discusses the application of SSM in modifying different thermoplastic polymers, highlighting various studies demonstrating the method's effectiveness in altering polymer properties. Finally, this work emphasizes SSM's importance in environmental sustainability and its potential in the recycling and upcycling of plastic materials. It acknowledges the challenges and future perspectives in the field, particularly regarding the scalability of SSM techniques for industrial applications and their role in advancing a circular economy in the polymer industry.

There is a continuous interest in cannabinoids like Δ9-tetrahydro cannabinol (Δ9-THC) and cannabidiol (CBD). A patent of Webster et al., described the conversion of CBD to either D8-THC or D9-THC, depending on the acid catalyst applied. The use of para-toluene sulfonic acid (pTSA) led to the formation of D8-THC, while boron trifluoride etherate (BF3·Et2O) yielded mainly D9-THC. The enormous difference in product selectivity between these two catalysts was investigated with Molecular Modeling. It was found that pTSA leads to fast isomerization of Δ9-CBD to Δ8-CBD and subsequent ring closure to Δ8-THC. BF3·Et2O catalysis leads to the formation of tertiary carbenium ions in the Transition States which yield D9-THC and some iso D8-THC. Under dry conditions in refluxing toluene, it was found that pTSA is predominantly present as a dimer, and only a small fraction is available as monomeric catalyst. Applying the computationally derived activation barriers in Transition State theory yielded reaction rates predicting amounts of cannabinoids that are in close agreement with the experimental findings.

Karate is a martial art that originated in Japan It is characterized by its diverse techniques, including punches, kicks, strikes, and open hand techniques. Generally, karate practitioners shall execute techniques fast, with an impactful finishing towards the target. The present study aims to examine the effectiveness of customized gym sessions in enhancing the athletes’ general performance with a duration of 3-months’time. A total of 7 tests were monitored, i.e., anthropometric measurement, sit and reach test, stork balance stand test, T-test, counter movement jump, 20m sprint, and Yo-Yo endurance test. 4 male amateur athletes (state representative) that has practiced karate for at least 6 years, with at least 5 days training per week, were selected. The age ranges from 15 to 20 years old. The athletes were requested to have a proper rest (at least 7 hours sleeping time) five days before the actual test day. The results show that all athletes have at least maintained or improved stork balance for both legs. The balance improvement ranges from 0% up to 134.69%. However, both the T-test and 20m sprint test demonstrated a negative outcome. The time consumed to complete 20m is increased, which deteriorated the linear speed capability by 1.89% up to 8.93%. Also, 3 out of 4 athletes show that the T-test performance does not provide a satisfactory achievement. The agility of athletes was found to drop by 3.58% up to 10.60%. Interestingly, the athletes’ stamina was found to improve based on the VO2 max prediction and Yo-Yo test. The enhancement of VO2 max prediction and Yo-Yo test recorded as 0% - 7.53% and 9.09% - 20%, respectively. So far, there is no clear indicator on the flexibility of the athletes’ spine and length of the hamstring muscles, based on the sit and reach test. Short-term gym sessions with a duration of 3 months might improve the strength and body balance of athletes. However, the impact on the responsiveness and agility of athletes did not show any significant breakthrough. In future study, it is recommended that a large sample of participants should be included in the analysis.

This paper proposes a metaphysical framework for distinguishing between human and machine intelligence. By drawing an analogy from Kant’s incongruent counterparts, it posits two identical deterministic worlds -- one comprising a human agent and the other comprising a machine agent. These agents exhibit different types of information processing mechanisms despite their apparent sameness in a causal sense. By postulating the distinctiveness of human over machine intelligence, this paper resolves what it refers to as “the vantage point problem” – namely, how to legitimize a determinist’s assertion of determinism by placing the determinist within the universe.

As the global community shifts away from fossil fuels towards more environmentally friendly energy alternatives, there is an escalating demand for sophisticated energy storage solutions. Solid-State Batteries (SSBs) have emerged as a promising advancement, presenting a superior substitute to conventional lithium-ion batteries. This review provides an in-depth examination of SSBs, emphasizing their enhanced energy density, safety, and longevity. We evaluate conventional cathode materials, including lithium cobalt oxide (LiCoO2), lithium manganese oxide (LiMn2O4), and lithium iron phosphate (LiFePO4). Additionally, we introduce emerging materials such as sulfides, oxides, and air-based cathodes, discussing their benefits, limitations, and their congruence with solid electrolytes. Special attention is devoted to the structural fine-tuning of cathode ma-terials, investigating approaches like nanostructuring, surface coatings, and composite strategies to counteract issues such as restricted conductivity and structural volatility. The review critically analyzes the electrical and thermal properties of these materials, which are essential for battery safety and efficacy. Moreover, we present a comparative assessment of cathode materials based on performance indicators and identify prevailing research voids and hurdles in the commerciali-zation of SSB cathodes. Concluding, we suggest prospective research directions and innovations, underscoring the revolutionary potential of SSB technologies in paving the way for a sustainable energy horizon.

The fact that quantum gravity does not admit a co-variant vacuum state has far-reaching consequences for all physics. It points out that space could not be empty, and we return to the notion of an ether . Such a concept requires a preferred reference frame for, e.g., universe expansion and black holes. Here, we intend to discuss vacuum and quantum gravity from three essential viewpoints: universe expansion, black holes existence, and quantum decoherence.

Covid-19 has become a non-natural national disaster that affects the national resilience of the Indonesian state. In maintaining national resilience, the implementation of state defense is needed. This research aims to describe the awareness of defending the state of millennials during the current situation of the Covid-19 pandemic in Indonesia by using a quantitative approach with descriptive analysis methods with survey techniques. The results of this study indicate that most millennials are aware of the obligation to defend the state amid the current Covid-19 pandemic, namely by implementing health protocols such as preparing cleaning equipment, conducting social distancing, and working from home. However, there are still millennials who cannot run it for some reason. Based on the results of this study, it concluded that most millennials are aware of the obligation to defend the state during a pandemic by complying with health protocols as a form of state defense character.

The exact dynamics of emergence remains one of the most prominent outstanding questions for the field of complexity science. I first discuss various perspectives on emergence in various contexts, then offer a different perspective on understanding emergence in a graph-theoretic representation. From the discussion, an observer’s choice in state space seems to have an effect for that observer to detect emergent behavior. To test these ideas, I analyze the dynamics of all possible spatial state spaces near the critical temperature in an Ising model. As a result, state space topologies that appear more deterministic flip more bits than topologies that appear more random, which is contrary to our intuitions about randomness. In addition, the size of different state spaces constrain a system’s ability to explore various states within the same time frame. These results are important to understanding emergent phenomena in biological systems, which are layered with various state spaces and observational perspectives.

Multipartite entanglement is a resource for application in disparate protocols, of computing, communication and cryptography. Nested entanglement provides resource-states for quantum information processing. In this paper, Matryoshka quantum resource-states, which contain nested entanglement patterns, has been studied. A novel scheme for the generation of such quantum states has been proposed using an anisotropic XY spin-spin interaction-based model. The application of the Matryoshka GHZ-Bell states for n-qubit teleportation is reviewed and an extension to more general Matryoshka ExhS-Bell states is posited. An example of Matryoshka ExhS-Bell states is given in the form of the genuinely entangled seven-qubit Xin-Wei Zha state. Generation, characterisation and application of this seven-qubit resource state in theoretical schemes for quantum teleportation of arbitrary one, two and three qubits states, bidirectional teleportation of arbitrary two qubit states and probabilistic circular controlled teleportation are presented.

Multipartite entanglement is a resource for application in disparate protocols, of computing, communication and cryptography. In this paper, generation, characterisation and application of a genuine genuinely entangled seven-qubit resource state is studied. Theoretical schemes for quantum teleportation of arbitrary one, two and three qubits states, bidirectional teleportation of arbitrary two qubit states and probabilistic circular controlled teleportation as well as three schemes for undertaking tripartite quantum state sharing are presented.

Solid state fermentation (SSF) is considered more sustainable than traditional fermentation because it uses low amounts of water and transforms agro-industrial residues into value added products. Enzymes, biofuels, nanoparticles and bioactive compounds can be obtained from SSF. The key factor in SSF processes is the choice of microorganisms and their substrates. Many fungal species can be used and are mainly used due their lower requirements of water, O2 and light. Residues rich in soluble and insoluble fiber are utilized by lignocellulolytic fungi because they have the enzymes that break fiber hard structure (lignases, celullases or hemicelullases). During the hydrolysis of lignin, some phenolic compounds are released but fungi also synthetize compounds such as mycophenolic acid, dicerandrol C, phenylacetates, anthraquinones, benzofurans and alkenyl phenols that have health beneficial effects such as antitumoral, antimicrobial, antioxidant and antiviral activities. Another important group of compounds synthetized by fungi during fermentation are polysaccharides that also have important health promoting properties. Fungal biofermentation has also proved to be a process which can release high contents of phenolics and it also increases the bioactivity of these compounds.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

In this paper a full state feedback control of a double inverted pendulum on a cart (DIPC) are designed and compared. Modeling is based on Euler-Lagrange equations derived by specifying a Lagrangian, difference between kinetic and potential energy of the DIPC system. A full state feedback control with H infinity and H 2 is addressed. Two approaches are tested: open loop impulse response and a double inverted pendulum on a cart with full state feedback H infinity and H 2 controllers. Simulations reveal superior performance of the double inverted pendulum on a cart with full state feedback H infinity controller.

The layer-by-layer (LBL) fabrication method allows for controlled microstructure morphology and vertical component distribution, and also offers a reproducible and efficient technique for fabricating large-scale organic solar cells (OSCs). In this study, polymer D18 and PYIT-OD are employed to fabricate all-polymer solar cells (all-PSCs) using the LBL method. Morphological studies reveal that the use of additives optimizes the microstructure of the active layer, enhancing the crystallinity and charge transport capability. The optimized device with 2% CN additive significantly reduces bimolecular recombination and trap-assisted recombination. All-PSCs fabricated by the LBL method based on D18/PYIT-OD deliver a power conversion efficiency (PCE) of 15.07%. Our study demonstrates the great potential of additive engineering via LBL fabrication method in regulating microstructure of active layers, suppressing charge recombination, and enhancing the photovoltaic performance of devices.

We suggest a new solution to the strong CP problem. The solution is based on the proper use of the boundary conditions for the QCD generating functional integral. It obeys the principle of renormalizability of Quantum Field Theory and does not involve new particles like axions.

Mechanochemical technology is developing rapidly, judging by the scientific information in both basic and applied studies. However, many issues and points of view remain to be discussed. This review presents some new key issues for the optimization of mechanochemical processes in theoretical and practical aspects. Emphasis is placed on powder technology aspects, which are not always discussed compared to functional or microscopic viewpoints. The transfer of chemical species across the interparticle interface between organic and inorganic species during the mechanosynthesis of nanocomposite oxides offers many new possibilities, which are discussed here in detail. Since all material transport is preceded by charge transfer, its driving force has been searched for using terminology beyond the well-established electrochemical ones. The role of organic compounds during the whole process is emphasized, regardless of their survival in the final product. The similarity with the pharmaceutical phenomena is pointed out, although its mentality is very different from that of the synthesis of nanocomposites. Not only for the rational amorphization of the active pharmaceutical ingredient, but also for the stabilization of molecular dispersion states with the participation of excipients are discussed. The effects of liquids, either added or formed by mechanochemical auto-liquefaction, are presented with reference to the comparison between wet and dry grinding. Finally, mechanisms of apparent stabilization of mechanically activated states of products are elucidated to investigate the practical applicability of mechanochemically synthesized products

In this article, we calculate the deflection angle of tidal charged black hole (TCBH) in weak field limits. First we obtain the Gaussian optical curvature and then apply the Gauss-Bonnet theorem on it. With the help of Gibbons-Werner method, we are able to calculate the light's deflection angle by TCBH in weak field limits. After calculating the deflection angle of light, we check the graphical behavior of TCBH. Moreover, we further find the light's deflection angle in the presence of plasma medium and also check the graphical behavior in the presence of plasma medium. Moreover, we investigate the shadow of TCBH.For calculating the shadow, we first find the null geodesics around the TCBH and then find its shadow radius. We also obtain TCBH's shadow in the plasma medium. Hence, we discuss the shadow of the TCBH using the $M87^{*}$ parameters announced by the Event Horizon Telescope.

Description of redox reactions is critically important for understanding and rational design of materials for electrochemical technologies including metal-ion batteries, catalytic surfaces, or redox-flow cells. Most of these technologies utilize redox-active transition metal compounds due to their rich chemistry and their beneficial physical and chemical properties for these types of applications. A century since its introduction, the concept of formal oxidation states (FOS) is still widely used for rationalization of the mechanisms of redox reactions, but there exists a well-documented discrepancy between FOS and the electron density-derived charge states of transition metal ions in their bulk and molecular compounds. We summarize our findings and those of others which suggest that density-driven descriptors are in certain cases better suited to characterize the mechanism of redox reactions, especially when anion redox is involved, which is the blind spot of the FOS ansatz.

Understanding the ionic channel network of proton exchange membranes, which dictate fuel cell performance, is crucial when developing proton exchange membrane fuel cells. However, itis difficult to characterize due to complicated nano structure and differing changes to their structure with different amounts of water uptake. Electrostatic force microscopy (EFM) can map surface charge distribution as nano special resolution by measuring the electrostatic force between a vibrating conductive tip and a charged surface under an applied voltage, . In this study, the ionic channel network of a proton exchange membrane is analyzed using EFM. A mathematical approximation model of the ionic channel network is first derived, to explain changes in force gradient on the surface using EFM. The phase lag of dry and wet Nafion under stepwise changes to bias voltage is then measured. Based on the model, variations in the ionic channel network of Nafion with different amounts of water uptake are analyzed numerically. The mean surface charge density of both membranes, which is connected with the ionic channel network, is calculated using the model. The results show that the difference between the mean surface charge of the dry and wet membranes is consistent with the variation in their proton conductivity.

Chemical versatility of organic semiconductors provides nearly unlimited opportunities for tuning their electronic properties. However, despite decades of research, relationship between molecular structure, molecular packing and charge mobility in these materials remains poorly understood. This reduces the search for high-mobility organic semiconductors to the inefficient trial-and-error approach. For clarifying the abovementioned relationship, investigations of the effect of small changes in the chemical structure on OSs properties are particularly important. In this study, we address computationally the impact of substitution of C-H atom pairs by nitrogen atoms (N-substitution) on molecular properties, molecular packing and charge mobility of crystalline oligoacenes. Besides of decreasing frontier molecular orbital levels, N-substitution dramatically alters molecular electrostatic potential yielding pronounced electron-rich and electron-deficient areas. These changes in the molecular electrostatic potential strengthen face-to-face and edge-to-edge interactions in the corresponding crystals and result in the crossover from the herringbone packing motif to π-stacking. When the electron-rich and electron-deficient areas are large, sharply defined and, probably, have certain symmetry, charge mobility increases up to 3-4 cm2V-1s-1. The results obtained highlight the potential of azaacenes for application in organic electronic devices and are expected to facilitate rational design of organic semiconductors for steady improvement of organic electronics.

The recycling, incineration, and final disposal rate of municipal solid waste (MSW) are calculated based on the total amount of waste input to each facility in many countries. These statistic data have serious limitation in setting the national goal and policy for effective waste management because it is not considering the amount of foreign objectives in the process of each life-cycle stage. This case study is to estimate the actual rates of recycling, incineration, and final disposal by material flow analysis (MFA) after the collection of MSW in Korea. The actual rates of recycling, incineration and final disposal for MSW in 2016 were 49.9%, 32.9% and 23.1% respectively, indicating that the recycling rate was lower by 10.1%, while the incineration and final disposal rates were raised by 7.6% and 8.4% respectively, compared with the statistics for current MSW. In addition, the changed actual rates of recycling, incineration treatment, and final landfill, and variation of waste treatment charge according to treated amounts per treatment method was analyzed. This results of this study will contribute to establish national level of plan on effective waste management.

The optical conductivity in the charge order phase is calculated in the extended Hubbard model describing an organic Dirac electron system α-(BEDT-TTF)₂I₃ using the mean field theory and the Nakano-Kubo formula. A peak structure due to interband excitation being characteristic in two-dimensional Dirac electron system is found above the charge order gap. It is shown that the peak structure originates from the Van Hove singularities of the conduction and valence bands, where those singularities are located at a saddle point between two Dirac cones in momentum space. The frequency of the peak structure exhibits drastic change in the vicinity of the charge order transition.