A novel high-speed directly modulated two-section distributed feedback (TS-DFB) semiconductor laser based on the detuned-loading effect is proposed and simulated. Grating structure is designed by reconstruction-equivalent-chirp (REC) technique. A π phase-shift is introduced into the reflection grating, which can provide a narrow-band reflection region with a sharp falling slope on both sides of the reflection spectrum, thus enhancing the detuned-loading effect. Owing to its unique dual-falling-edges structure the bandwidth can be improved even when the lasing wavelength shifts beyond the left falling edge due to thermal effect in actual test, in which condition the detuned-loading effect can be used twice, which greatly improves the yield. The modulation bandwidth is increased from 17.5 GHz for a single DFB laser to around 24 GHz when the lasing wavelength is located on the left falling edge of the TS-DFB laser based on detuned-loading effect, and can be increased to 22 GHz for the right side. An eight-channel laser array with precise wavelength spacing is investigated, with side mode suppression ratio (SMSR) > 36dB. Besides, TS-DFB lasers with uniform reflection grating are studied and simulated result shows that modulation characteristic is far inferior to the laser with a phase-shifted grating reflector.

We propose an asynchronous acoustic chirp slope keying to map bit sequences on single or multiple bands without preamble or error correction coding on the physical layer. Details of the implementation are disclosed and discussed, the performance verified on laboratory scale in a pool measurement, as well as simulated for a channel containing Rayleigh fading and Additive White Gaussian Noise. For time-bandwidth products of 50 in single band mode, a raw data rate of 100~bit/s is simulated to achieve bit error rates below 0.001 for signal-to-noise ratios above -6~dB. In dual-band mode and a data rate of 200~bit/s, this bit error level was achieved for signal-to-noise ratios above 0~dB for time-bandwidth product of 25. The packet error rates follow this behavior with an offset of 1~dB.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

Enophthalmos is a severe complication of primary reconstruction following orbital floor frac-tures, oncological resections or maxillo-facial syndromes. The goal of secondary reconstruction is to re-store symmetrical globe positions to recover function and aesthetics. In this article we pre-sent a method of computer-assisted orbital floor reconstruction using a mirroring technique and a customized titanium or high-density polyethylene mesh, printed using computer aided manufac-turing techniques. This reconstructive protocol involves 4 steps: mirroring of the healthy orbit at the affected site, vir-tual design of a patient specific orbital floor mesh, computer-assisted manufacturing (CAD) of the implant, and surgical insertion of the device. Using a computed tomography data set, the un-injured side of the craniofacial skeleton was reflected onto the contralateral injured side, and a reconstructive orbital floor prosthesis was virtually designed on the mirrored orbital bone sur-face. The solid-to-layer (.STL) files of the prosthesis were then manufactured using Direct Metal Laser Sintering (DMLS) or Computer Numerical Control (CNC) methods, leading to the produc-tion of 10 titanium meshes and 2 high density polyethylene (HDPE) implants. Clinical outcomes were assessed using 3dMD photogrammetry and computed tomography measures in 14 treated patients. The technique described here appears to be a viable method to correct complex orbital floor de-fects needing delayed reconstruction. This article represents the prosecution of a previous study, which is part of a wider experimental protocol for orbital floor reconstruction using comput-er-assisted design-computer-assisted manufacturing (CAD-CAM) technology

(1) Importance of problem: Breast cancer accounted for 685.000 deaths globally in 2020, and half of all cases occur in women with no specific risk factor beside gender and age-group. During last 4 decades we see a reduction by 40% of age-standardized breast cancer [1], which in turn means that the number of mastectomies performed for younger women increased, raising the need for adequate breast reconstructive surgery. Advances in oncological treatment have made it possible to limit the extent of what represents radical surgery for breast cancer, yet in the past decade, we see a marked trend toward mastectomy in breast conserving surgery eligible patients [2]. Prophylactic mastectomy has also registered an upward trend [3,4]. This trend together with new indication for breast reconstruction like chest feminization in transgender patients [5] have increased the need for breast reconstruction surgery. (2) Purpose: The purpose of this study is to analyze the types of reconstructive procedures, their indications, their limitations, their functional results and the safety profiles when used during the integrated treatment plan of the oncologic patient; (3) Methods: We conducted an extensive literature review of the main reconstructive techniques, especially the autologous procedures, summarized the findings and presented a few cases from our own experience for exemplification of the usage of breast reconstruction in oncologic patients. (4) Conclusions: Breast reconstruction has become a necessary step in the treatment of most breast cancers and many reconstructive techniques are now routinely practiced. Microsurgical techniques are considered the "gold standard", but they are not accessible to all services, from a technical or financial point of view, so pediculated flaps remain the safe and reliable option, along with alloplastic procedures, to improve the quality of life of these patients.

Due to nonlinear components in the charging piles of electric vehicles, harmonics and non-stationary signals in the electric vehicle charging load brings voltage and current distortion, seriously affecting the accuracy of the power-related calculation in non-sinusoidal environments. This paper proposed a new approach to calculate the active power and root mean square values from decomposed components using the adaptive chirp mode decomposition (ACMD) method on voltage and current. The advantage of the ACMD-based method is that it correctly provides the power-related quantities of harmonics or non-stationary components for the electric vehicle charging load. The performance of the proposed method was verified using synthetic signals and simulation tests. The experimental results presented better estimations for each quantity defined in IEEE Standard 1459-2010, compared with the discrete wavelet transform approach.

Critical sized bone defects and articular cartilage injuries resulting from trauma, osteonecrosis or age-related degeneration are often nonhealing by the physiological repairing mechanisms, thus representing a clinic issue due to the relevant epidemiological incidence. Current treatment approaches consist of autologous or allogenic grafting, which are associated with painfulness, morbidity, risk of infections and rejection. Novel tissue-engineering approaches, aiming at the reconstruction of damaged tissues, have been proposed as alternative solutions to these conven-tional methods. These approaches are based on the combination of three fundamental compo-nents: autologous or allogenic cells, a scaffold and growth-stimulating signals, which are gener-ally referred to as the tissue engineering triad. Three-dimensional polymer networks are fre-quently used as scaffolds to allow cell proliferation and tissue regeneration. In this scenario, cryogels are giving promising results as cell scaffolds over other polymer networks, thanks to their peculiar properties. In particular, cryogels possess an interconnected porous structure and a typical sponge-like behaviour, which facilitate the cellular infiltration and ingrowth. Their properties can be appropriately adjusted to match the requirements of the specific tissue or or-gan that it is intended to regenerate. In this review it is reported the state of the art on the fabri-cation and employment of cryogels in supporting osteo or chondro-genic differentiation for the re-building of more organized tissues. Moreover, it will highlight current progress and future perspectives in the implementation of this technology in the clinical practice.

For equivalent modeling of mixed wind farms (WFs), existing clustering indicators cannot consider the complex coupling characteristics between different types of wind turbines (WTs). This paper proposes a refined equivalent modeling method for mixed WFs based on artificial intelligence technology. Firstly, the electromechanical transient performance of mixed WFs is analyzed. The WT type, wind speed and direction, and voltage dip are considered the main factors affecting the external dynamic response of mixed WFs. Secondly, the equivalent node model is established, including the selection of independent and dependent variables. Then, the multiple artificial neural networks (ANNs) are trained one by one based on sample data, to explore the nonlinear relationship between the dependent variables and the independent variables. Finally, the electromechanical transient simulations of the power systems with a mixed WF is carried out by using the MATLAB platform. Simulation results show that the proposed model can reflect the external characteristics of the mixed WF in different wind scenarios and voltage dips.

For the problem of poor accuracy of the existing multi-rate simulation methods, this paper proposes a multi rate real-time simulation method based on the Norton equivalent, compared with multi-rate simulation method based on the ideal source equivalent. After the Norton equivalence of the fast subsystem and the slow subsystem, they are obtained simultaneously at the junction nodes. In order to reduce the amount of simulation calculation, the Norton equivalent circuit is obtained by incremental calculation. The data interface between the fast subsystem and the slow subsystem is realized by extrapolation method. For ensuring the real-time performance of the simulation, the method that the slow subsystem calculates ahead of the fast subsystem is given for the slow subsystem with a large amount of calculation. Finally, the AC/DC hybrid power system was simulated on the real-time simulation platform (FRTDS), and the simulation results were compared with the single-rate simulation, which verified the correctness and accuracy of the method.

The incidence of breast cancer and therefore need for breast reconstruction is expected to increase. The many reconstructive options available and the changing aspects of the field make this a complex area of plastic surgery, requiring knowledge and expertise. Two major types of breast reconstruction can be distinguished: Breast Implants and Autologous Flaps. Both present advantages and disadvantages. Autologous fat grafting is also commonly used. MRI is the modality of choice for evaluating breast reconstruction. Knowledge of the type of reconstruction is preferable to provide the maximum of pertinent information and avoid false positives. Early complications include seroma, hematoma, and infection. Late complications depend on the type of reconstruction. Implant rupture and implant capsular contracture are frequently encountered. Depending on the implant type, specific MRI signs can be depicted. In case of myocutaneous flap, fat necrosis, fibrosis and vascular compromise represent the most common complications. Late cancer recurrence is much less common. Rare reported late complications include breast implant associated large cell anaplastic lymphoma (BIA-ALCL) and, recently described and even rarer, Breast implant-associated squamous cell carcinoma (BIA-SCC). In this review article, the various types of breast reconstruction will be presented, with emphasis on pertinent imaging findings and complications.

Pure monocular 3D reconstruction is an ill-posed problem that has attracted the research community's interest due to the affordability and availability of RGB sensors. SLAM, VO, and SFM are disciplines formulated to solve the 3D reconstruction problem and estimate the camera’s ego-motion, so many methods have been proposed. However, most of these methods were not evaluated in large datasets, under various motion patterns, had not been tested under the same metrics, and most of them had not been evaluated following a taxonomy, making their comparison and selection difficult. In this research, we performed a comparison of ten publicly available SLAM and VO methods following a taxonomy, including one method for each category of the primary taxonomy, three machine learning-based methods, and two updates of the best methods, to identify the advantages and limitations of each category of the taxonomy and test if the addition of machine learning or the updates made on those methods improved them significantly. Thus, we evaluated each algorithm under the TUM-Mono benchmark and performed an inferential statistical analysis to identify significative differences through its metrics. Results determined that sparse-direct methods significantly outperformed the rest of the taxonomy, and fusing them with machine learning techniques significantly improves the performance of geometric-based methods from different perspectives.

Introduction: Anterior cruciate ligament (ACL) tears are a common injury among athletes, including NBA players. Advances in surgical techniques, rehabilitation protocols, and complementary therapies have greatly improved the outcomes for athletes undergoing ACL reconstruction surgery. Arthroscopic surgery has become the standard approach for ACL reconstruction due to its minimally invasive nature, resulting in less pain, faster recovery, and better outcomes. Accelerated rehabilitation protocols have been shown to improve outcomes by getting athletes back to playing sooner and with better functional outcomes than traditional rehabilitation programs. Physiotherapy has also played an important role in helping athletes return to play by using targeted exercises to improve range of motion, strength, and stability. Complementary therapies, such as phytotherapy, have also shown promise in aiding the healing process. These advancements in ACL tear treatment have the potential to improve outcomes for NBA players who suffer from these injuries and further research can help continue to improve prevention and management of these injuries. Methods: The study is a retrospective cohort study that focuses on NBA players who suffered from ACL tears and underwent reconstructive surgery between 2012 and 2022. The study excluded players who had not played prior to experiencing an ACL injury, players with a concurrent significant knee injury involving other ligaments, any other major leg injury, or a history of ACL tear in the contralateral knee. The study gathered data on 25 players and recorded game statistics for each player before and after surgery to assess the impact of ACL tears on players' game performance. The recorded data was analyzed using SPSS Statistics.Results: The mean age at injury was 26.12 ± 4.3 years, and the majority of injuries occurred on the left side. players experienced significant decreases in minutes per game and points per game, with a reduction of 5.9 and 3.5, respectively, during the season following the injury. Moreover, players exhibited a statistically significant decline in rebounds per game and assists per game, with a decrease of 0.91 and 1.11, respectively. These findings suggest that ACL injuries can have a severe impact on a player's ability to contribute to their team's success. The study did not find a significant difference in shooting percentages for two-pointers, three-pointers, and free throws before and after ACL injury. This suggests that ACL injuries do not significantly affect a player's shooting abilities. Discussion: This study focused on the incidence and impact of ACL injuries among NBA players between 2012 and 2022. The study found that ACL injuries had a significant negative impact on a player's performance, including decreases in minutes, points, rebounds, and assists per game. The mean time to return to play after ACL surgery was consistent with previous studies. The study also highlighted the importance of effective prevention, treatment, and rehabilitation strategies, with neuromuscular training programs showing promise in reducing the incidence of ACL injuries. While ACL injuries did not significantly affect shooting percentages, further research is needed to fully understand their impact on shooting performance. Conclusion: The study sheds light on the frequency and effects of ACL injuries in NBA players and emphasizes the importance of implementing effective strategies for preventing, diagnosing, and treating such injuries in order to help players recover and return to their previous level of performance.

The Stepped Frequency Waveform (SFW) is commonly employed in radar technology to synthesize wideband signals through the aggregation of narrow-band pulses, thereby achieving high-resolution range profiles without the need to increase the radar's instantaneous bandwidth. However, the inherent large time-bandwidth product of SFW introduces substantial ranging errors and energy dispersion, which significantly hinders its efficacy in detecting high-speed objects. This paper introduces a pioneering velocity estimation technique utilizing the fractional Fourier transform (FrFT) to address these limitations. Leveraging the characteristic of the Doppler signal from a moving target, which manifests as a chirp signal with a rate proportional to the target's velocity, the FrFT is utilized for precise velocity estimation. Subsequent to this, velocity compensation is applied using the deduced metrics, followed by the application of the inverse fast Fourier transform (iFFT) to pinpoint the target's exact location. To optimize the computational efficiency of determining the FrFT's optimal order, we propose an iterative algorithm founded on the golden section search method. The effectiveness of the proposed approach is verified by simulation data, and the results demonstrate that the proposed approach can accurately estimate the velocity and the range of the high-speed targets with a relatively low computational complexity.

With the vast amount of goods being shipped around the world, there is a need to track and manage various types of assets, particularly shipping containers. Logistics industries dealing with small facilities, shipments, equipment, and vehicles must be tracked. There are many applied asset tracking systems such as Radio-Frequency Identification (RFID), Bluetooth Low Energy (BLE) Beacon, and Long-Range Radio (LoRa). This paper presents these systems and focuses on locating assets using LoRaWAN technology, which has a positive impact on the responsive and sustainable cities in Egypt. IoT-based Long Range (LoRa) is a low-power, wide-area communication technology that uses radio frequencies to transmit data over long distances. The extended range, low power consumption, low maintenance, and the ability to store location data when the end node that needs to connect to the asset is out of the gateway's coverage make LoRa a good choice for developing asset-tracking applications. This paper introduces a real-time tracking experiment as a result of a project implementation, whose goals are aligned with industry, innovation, and infrastructure and Sustainable Cities and Communities, the Sustainable Development Goals (SDGs) No. 9 and 11.

Background: The aim of the study is to present the process of monitoring the changes in the effi-ciency of equilibrium reactions in the children with postural disorders, in the course of the thera-peutic process. Methods: The shape of spine and the efficiency of equilibrium reactions in standing posture and during gait were assessed in all the subjects. The subjects were put in 2 groups: with the shape of spine disorder and without one. The recommended set of therapeutic activities in home conditions lasted about 20 minutes and was performed by the child with parent’s supervision. The therapeutic program was based on elements of the PNF and Vojta methods. The following parameters were measured: maximum movement of the center of presure (CoP) in the frontal plane during gate, maximum movement of the CoP in the sagittal plane, movement of the CoP in the frontal plane in static conditions, movement of the CoP in the sagittal plane in static conditions. Results: Six statistically significant differences were recorded, all of them were related to measurement I. The Friedman test result was statistically significant for all the indexes. Post-hoc analyzes were performed using the Dunn-Bonferroni test. Conclusions: 1. The children with shape of spine disorders are featured by lower efficiency of equivalent reactions in relation to the children without disorders. 2. The therapy with the application of neurophysiological methods in the treatment of shape of spine disorders improves equilibrium reactions in these patients. 3. Long-lasting and thorough observations of the therapeutic process in the children with shape of spine disorders should include the monitoring of the efficiency of equilibrium reactions

Since the discovery of graphene, due to its excellent optical, thermal, mechanical and electrical properties, it has a broad application prospect in energy, materials, biomedicine, electromagnetism and other fields. A great quantity of researches on the physical mechanism of graphene has been applied to engineering in electromagnetism and optics. To study the properties of graphene, different kinds of numerical methods have been developed for simulating the electromagnetic field effects of graphene, and equivalent boundary conditions have been employed to replace graphene in the computational domain. In this work, the numerical methods with equivalent boundary conditions are reviewed, and some examples are provided to illustrate their applicability.

For a graph G, let P(G, λ) be its chromatic polynomial. Two graphs G and H are said to be chromatically equivalent if P(G,λ) = P(H,λ). A graph is said to be chromatically unique if no other graph shares its chromatic polynomial. In this paper, chromatic polynomial of the necklace graph N_n, for n ≥ 2 has been determined. It is further shown that N₃ is chromatically unique.

In real financial markets, the certainty equivalent rate is an important factor for investors to consider. From the value of a specific company’s certainty equivalent rate, investors can judge if this company is worth investing in. In this paper, we will explore how to obtain the value of the certainty equivalent rate so that we can evaluate a given company. First, we will introduce the theoretical support of this paper, which is put-call parity. From put-call parity, we will derive the mathematical expression for the certainty equivalent rate. Second, we will use the mathematical expression for the certainty equivalent rate to perform an empirical study. We will consider some extreme examples, including some of the best- and worst-performing stocks up to this point in 2023. Based on these stocks’ data, we will visualize the performance of these stocks and explain the meaning of the data. Finally, we will apply the results to a very popular industry—the electric vehicle industry—to explore the current electric vehicle market situation in the U.S.A.

Three-Dimensional reconstruction of the corneal surface provides a powerful tool for managing corneal diseases. This study proposes a novel method for reconstructing the corneal surface from elevation point clouds, using modal schemes capable of reproducing corneal shapes using surface polynomial functions. The multivariable polynomial fitting was performed using a non-dominated sorting multivariable genetic algorithm (NS-MVGA). Standard reconstruction methods using least-squares discrete fitting (LSQ) and sequential quadratic programming (SQP) were compared with the evolutionary algorithm-based approach. The study included 49 eyes of 49 patients (ages 11-63) sorted in two groups: control (33 eyes) and keratoconus (KC) (16 eyes). Tomographic information (Sirius, Costruzione Strumenti Oftalmici, Italy) was processed using Matlab. The goodness of fit for each method was evaluated using mean squared error (MSE), measured at the same nodes where the elevation data were collected. Polynomial fitting based on NS-MVGA improves MSE values by 86% compared to LSQ-based methods in healthy patients. Moreover, this new method improves aberrated surface reconstruction by 43% for Amsler-Krumeich (AK) Grade 1 keratoconus patients. Finally, significant improvements were also found in morpho-geometric parameters, such as asphericity and corneal curvature radii.

The production of municipal solid waste incineration bottom ash (MSWIBA) is very massive and has the potential to replace cement despite the problems of complex composition, uneven particle size distribution, and low reactivity. This paper adopts sodium silicate activation of MSWIBA-slag to improve the reactivity to prepare composite cementitious materials. It explores the hydration performance study of the composite cementitious materials by isothermal calorimetric analysis, Fourier Transform Infrared (FTIR) spectroscopy, XRD physical diffraction analysis, and SEM/EDS tests. SEM/EDS tests will be used to explore the hydration properties of the composite gelling. The results showed that with the increase of MSWIBA doping, the porosity between the materials increased, the degree of Hydration decreased, and the compressive strength decreased with the rise of MSWIBA. When sodium silicate increased from 25% to 35%, too much alkaline material occurred over the alkaline effect, which inhibited the Hydration of the particles, and the degree of hydration reaction decreased, and the compressive strength decreased accordingly; the exothermic process of Hydration can be mainly divided into five stages, quartz and calcite did not participate in the hydration reaction completely, and sexual aluminum participated in the hydration reaction. The vibrational peaks of Si-O-Ti (T = Si and Al) were present in the material. The vibrational peaks of XRD, FTIR, and SEM-EDS all indicate the presence of silica-aluminate network structures in the hydration products, mainly N-A-S-H and C-A-S-H gels.

Cassava Solid waste (Onggok) is a solid waste from the cassava-based tapioca industry, the starch content in Onggok is still 50-80 wt.% of residual starch, which can be used to produce maltodextrin for foods application. Furthermore, using cassava solid waste is beneficial in terms of the cost of raw materials. The starch content in cassava can be modified through enzymatic hydrolysis using α-amylase and β-amylase enzymes at 80oC and pH 5.5. Enzymatic hydrolysis was done using mixed enzymes that varied the concentration of α-amylase at 0,.1% and the β-amylase enzymes at 0.05, 0.1, and 0.5%. the concentration of cassava waste (Onggok) varied from 4%, 7%, 10%, and 13%. The optimum concentration of α-amylase and β-amylase enzymes are 0.1% and 0.1% respectively at time intervals of 1 minute resulting in a dextrose equivalent (DE) value 0f 5.7. The characteristics of maltodextrin were studied using scanning electron microscopy (SEM) to determine the morphology of the starch structure which had changed due to the enzyme hydrolysis. Simultaneous thermal analysis (STA) was studied to determine the Thermal stability of hydrolysis products. Maltodextrin produced from cassava waste (Onggok) has a DE value < 10, which has the potential to be used in the pharmaceutical industry

In this work, the transport equations of ionic species in concrete are studied. First, the equations at the porescale are considered, which are then averaged over a representative elementary volume. The so obtained transport equations at the macroscopic scale are thoroughly examined and each term is interpreted. Furthermore, it is shown that the tortuosity-connectivity does not slow the average speed of the ionic species down. The transport equations in the representative elementary volume are then compared with the equations obtained in an equivalent pore. Lastly, comparing Darcy’s law and the Hagen-Poiseuille equation in a cylindrical equivalent pore, the tortuosity-connectivity parameter is obtained for four dierent concretes. The proposed model provides very good results when compared with the experimentally obtained chloride profiles for two additional concretes.

In this paper, the design process of BLDC adopting the dual rotor method that can reduce the overall size of the motor while generating the same torque as the conventional Permanent Magnet BLDC is analyzed. A simple size is selected by obtaining the torque per rotor volume (TRV), and a method of matching the counter electromotive force by selecting the pole arc of the magnet through a magnetic equivalent circuit is analyzed. Since the efficiency is low because the 120-degree commutation method is selected, the middle stator is optimized through detailed design through the experimental design method. Afterwards, it has the advantage of being able to shift without stopping due to the characteristic of a dual rotor. For this, an analysis of the driving characteristics for each mode is performed.

We present the Lagrangian and Hamiltonian formulations of a theory for spin 2 fields. The construction is developed in flat space-time. The construction in curved space-time is conceptually straightforward, although it is not unique. The theory is based on a symmetric tensor $S_{\mu\nu}$, contains two degrees of freedom of radiation, is motivated by the teleparallel formulation of general relativity, and displays a certain resemblance with Maxwell's theory for the electromagnetic field.

This research presents the creation of a Virtual Reality experience for the Balzi Rossi museum, commemorating the centenary of Prince Albert I Grimaldi's archaeological work at the site. The project, a collaboration between the University of Genoa's 3D Lab Factory, Eurodrone, and the Balzi Rossi archaeological museum, aims to preserve and convey the site's heritage through advanced VR technology. Initially employing Unreal Engine 4, the team used photogrammetry for 3D reconstruction of the "Caviglione" and "Florestano" caves, notable for their ancient rock engravings. This first VR model, despite hardware limitations, provided an interactive exploration of the site. The subsequent development phase utilized Unreal Engine 5, incorporating Nanite technology for enhanced visual fidelity. This advancement resulted in a more detailed and immersive VR experience, presenting the Balzi Rossi cliff across different historical periods, including the Würm glaciation. Key to this phase was optimizing the VR experience for performance, focusing on stable frame rates and minimizing motion sickness, and integrating a multi-lingual interface for broader accessibility. Since November 2023, the VR setup at the Balzi Rossi Museum has been an educational and interactive feature, enabling visitors to explore the site's history virtually. This research demonstrates the potential of VR in cultural heritage preservation and education, providing a foundation for future technological improvements in the field.

Remote sensing-based models usually have difficulty in generating spatio-temporally continuous terrestrial evapotranspiration (ET) due to cloud cover and model failures. To overcome this problem, machine learning methods have been widely used to reconstruct ET. However, studies comparing and evaluating the accuracy and effectiveness of reconstruction among different machine learning methods remain scarce. In this study, four popular machine learning methods (deep forest, deep neural network, random forest, extreme gradient boosting) were used to reconstruct the ET product, addressing gaps resulting from cloud cover and model failure. The ET reconstructed by four methods were evaluated and compared in Heihe River Basin. The results showed that four methods performed well in the Heihe River Basin, but the RF method was particularly robust. It not only performed well compared with ground measurement (R = 0.73), but also reconstructed ET throughout the basin. Validation based on ground measurement showed that DNN and XGB models performed well (R > 0.70). However, few gaps still existed in the desert after reconstruction, especially for the XGB model. The DF model filled these gaps throughout the basin, but the model had lower consistency compared with ground measurement (R = 0.66) and yielded many low values. The results of this study suggested that machine learning methods had considerable potential in reconstruction of ET at regional scale.

In the present work, the main methodologies used to reconstruct wind fields in the U-SPACE have been analyzed. The SESAR U-SPACE program aims to develop an Unmanned Traffic Management system with a progressive introduction of procedures and services designed to support a secure access to the air space for a large number of drones. The Italian Aerospace Research Center (CIRA) is carrying out the EDUS project focused on the development and validation of operating platform demonstrators serving the micro-scale weather forecasts and the collection of information necessary for the definition of the flight plan of the drones in urban contexts. For this reason, the state of art methodologies that can be used to estimate winds at low altitudes in urban areas starting from available observational data have been reviewed in the present paper. Some of these techniques were originally developed for reconstruction at high altitudes, but successively adapted to treat different heights. A common approach to all techniques is to approximate the probabilistic distribution of wind speed over time with some parametric models, apply spatial interpolation to the parameters and then read the predicted value.

(1) Purpose: This work aims at developing a generalizable MRI reconstruction model in the meta-learning framework. The standard benchmarks in meta-learning are challenged by learning on diverse task distributions. The proposed network learns the regularization function in a variational model and reconstructs MR images with various under-sampling ratios or patterns that may or may not be seen in the training data by leveraging a heterogeneous dataset. (2) Methods: We propose an unrolling network induced by learnable optimization algorithms (LOA) for solving our nonconvex nonsmooth variational model for MRI reconstruction. In this model, the learnable regularization function contains a task-invariant common feature encoder and task-specific learner represented by a shallow network. To train the network we split the training data into two parts: training and validation, and introduce a bilevel optimization algorithm. The lower-level optimization trains task-invariant parameters for the feature encoder with fixed parameters of the task-specific learner on the training dataset, and the upper-level optimizes the parameters of the task-specific learner on the validation dataset. (3) Results: The PSNR increases 1.5 dB on average compared to the network trained through conventional supervised learning on the seen CS ratios. We test the result of quick adaption on the unseen tasks after meta-training, the average PSNR arises 1.22 dB compared to the conventional learning procedure that is directly trained on the unseen CS ratios in the meanwhile saving half of the training time. The average PSNR arises 1.87 dB for unseen sampling patterns comparing to conventional learning; (4) Conclusion: We proposed a meta-learning framework consisting of the base network architecture, design of regularization, and bi-level optimization-based training. The network inherits the convergence property of the LOA and interpretation of the variational model. The generalization ability is improved by the designated regularization and bilevel optimization-based training algorithm.

Re-creation of the past of historical buildings sits at the intersection of the spatio-temporal manifestation of cultural memories, socio-cultural meanings, values and identity re-moulds and refines the existing understanding and sense of place. Digital technologies have become a popular tool in re-creation of the past by creating a new body of knowledge and historical discourse based on identifying the gaps within our written histories. Designers and policymakers around the world have been exploring various tools and technologies such as diachronic modelling yet there is a gap in evidence-based understanding regarding the actual functioning and success of application for place making. This paper, therefore, sets out to scrutinise the role of digital technologies in facilitating digital place making. To do so, it investigates the potential of a new “digital heritage” narrative in the revival of the lost architectural narrative of the Dennys Lascelles Wool Store, Geelong. The proposed paper aims to investigate the potential of a new “digital heritage” narrative and story-telling as a means towards digital place making framework. While exploring the new and unique capabilities provided by the digital narrative in capturing, simulating and disseminating ‘lost’ heritage it will further imbue a sense of place by connecting the everyday city dweller.

Much has been learned about the interaction between myosin and actin through biochemistry, in vitro motility assays and cryo-electron microscopy of F-actin decorated with myosin heads. Comparatively less is known about actin-myosin interactions within the filament lattice of muscle, where myosin heads function as independent force generators and thus most measurements report an average signal from multiple biochemical and mechanical states. All of the 3-D imaging by electron microscopy that has revealed the interplay of the regular array of actin subunits and myosin heads within the filament lattice has been accomplished using the flight muscle of the large waterbug Lethocerus sp. Lethocerus flight muscle possesses a particularly favorable filament arrangement that enables all the myosin cross-bridges contacting the actin filament to be visualized in a thin section. This review covers the history of this effort and the progress toward visualizing the complex set of conformational changes that myosin heads make when binding to actin in several static states as well as fast frozen actively contracting muscle. The efforts have revealed a consistent pattern of changes to the myosin head structures determined by X-ray crystallography needed to explain the structure of the different acto-myosin interactions observed in situ.

This work presents a numerical study on atmospheric sound propagation over rough water surfaces. A method to generate pseudorandom sea profiles consistent with sea wave spectra is presented. The proposed method is suited to capture the logarithmic nature of the energy distribution of the waves. Sea profiles representing fully developed seas for sea states 2, 3, 4 and 5 are generated from the Elfouhaily et al. (ECKV) sea wave spectra. Excess attenuation caused by refraction and surface roughness is predicted with a parabolic equation (PE) solver. A novel method to estimate equivalent effective impedance based on PE predictions at different sea states is presented. Parametric expressions using acoustic frequency and significant wave height are developed for effective surface impedances. In this work, sea surface roughness is on a scale comparable to the acoustic wavelength. Under this condition, the acoustic scattering is primarily incoherent. This work shows the limitations of using an equivalent surface impedance in such incoherent scattering cases.

This article develops applications of the generalized method of lines to numerical solutions of the time-independent, incompressible Navier-Stokes system in fluid mechanics. We recall that for such a method, the domain of the partial differential equation in question is discretized in lines (or more generally in curves), and the concerning solutions are written on these lines as functions of the boundary conditions and the domain boundary shape.

Intercropping as a practice is very crucial in livelihood sustainability among smallholder farm-ing communities in many growing countries. However, for most cropping systems, the benefits of intercropping have yet to be optimized due to a lack of knowledge regarding spatial ar-rangements and planting densities. The objective of the study was to find out the profitability of maize-vegetable intercropping and the yields obtained from various spatial arrangements and planting densities of intercrops. From May to October 2019 and 2020 respectively, Experimental trials were set up in the rainy season in Northern, Upper West and Upper East regions of Ghana comprising of eight treatments each. A randomized complete block experimental design was used for the field layout with three to four replications. Data was collected on grain and fruit yield and land equivalent ratios was estimated (LER). At the end of the trial, important spatial arrangements and planting densities were identified that can be adopted by smallholder famers for system intensification. For okra, the optimal intercropping system under sufficient rainfalls was 2 okra rows at higher density and 2 maize rows at lower density for Upper West Region. In Upper East Region, the optimal spatial arrangement to recommend is 1 row of maize at recom-mended density: 2 rows of okra at lower density under well distributed rainfalls. For roselle, intercropping with spatial arrangement of 2 rows of maize at higher density: 1 row of okra at recommended density was recommended in Northern Region.

In this work 144 reinforcing bars of high-ductility steel named B500SD were subjected to an accelerated corrosion treatment and then tested under tension at different loading speeds in order to assess the effect of corrosion on the ductility properties of the rebars. Results showed that the bars with a corrosion level as low as the one reducing the steel mass by 1% gave rise to a significant degradation on the ductility properties with strain-stress curves losing the yield plateau and behaving practically as cold deformed steel bars. This effect took place at every tested loading speed. Thus, the research significance relies on the assessment of the influence of the loading speed at which the tensile test is performed given that it affects the ductility properties of the reinforcement bars.

One of the frequently used classes of the sparse reconstruction algorithms is based on the iterative shrinkage/thresholding procedure, where the thresholding parameter controls a trade-off between the algorithm accuracy and the execution time. In order to avoid this trade-off, we propose using a fast intersection of confidence interval method in order to adaptively control the threshold value through the reconstruction algorithm iterations. We have upgraded the two-step iterative shrinkage thresholding algorithm with a such procedure, improving its performance. The proposed algorithm, denoted as the FICI-TwIST, along with a few selected state-of-the-art sparse reconstruction algorithms have been tested on the classical problem of image recovery by emphasizing the image sparsity in the discrete cosine and the discrete wavelet domain. Furthermore, we have derived a single wavelet transformation matrix which avoids wrapping effects achieving significantly faster execution times when compared to more traditional function based transformation. The obtained results indicate competitive performance of the proposed algorithm, even in cases where all algorithm parameters have been individually fine-tuned for best performances.

An irreparable rotator cuff tear is a challenging condition to treat, and various treatment modalities are being introduced. Medialization in the partial repair method has the limitation of exposing the tuberosity, while tension-free biologic interpositioning tuberoplasty using acellular dermal matrix (ADM) has the limitation of exposing the humeral head. The authors believe that by combining these two techniques, it is possible to complement each other's limitations. Therefore, they propose a surgical method that combines medialization and biologic interpositioning tuberoplasty for addressing these constraints.

In the present work, a methodology for wind field reconstruction based on the Meteo Particle Model (MPM) from Numerical Weather Prediction (NWP) data is presented. The development of specific wind forecast services is a challenging research topic, in particular for what concerns the availability of accurate local weather forecasts in highly populated areas. Currently, even if NWP Limited Area Models (LAMs) are run at spatial resolution of about 1 km, this level of information is not sufficient for many applications, for example to support drone operation in urban contexts. The coupling of MPM with the NWP Limited Area Model COSMO has been implemented in such a way that the MPM reads the NWP output over a selected area and provides wind values in the generical point considered for the investigation. The numerical results obtained reveal a good behavior of the method in reproducing the general trend of wind speed, as confirmed also by the power spectra analysis. The MPM is able to step over the intrinsic limitations of the NWP model in terms of spatial and temporal resolution even if the MPM inherits the bias that inevitably affects the COSMO output.

The 3D reconstruction of vermiculite-based sealing material was carried out based on CT scanning experiments and Avizo software. The precision and representation of the reconstructed digital core were tested by calculating the pore structure parameters and comparing them with the experimental results of mercury compression. Avizo is a perfect interface with Fluent software to perform micro-scale seepage simulation to explore the distribution of pressure and velocity fields during fluid transport. In this paper, a new approach is proposed to study the penetration leakage of non-metallic gaskets by using equivalent pore networks.

Early debridement and stabilization for pyogenic spondylodiscitis allow early mobilization of the patient and prevent subsequent spinal deformity. Tantalum (Ta) trabecular metal (TM) components have several potential advantages over conventional implant materials, such as its uniformity and structural continuity, strength, low stiffness, high porosity, high coefficient of friction and tantalum trabecular metal enhances the host defense mechanism by increasing leukocyte chemotaxis, phagocytosis, and the bacterial killing rate. A single-stage surgery with a tantalum trabecular metal cage combining two different approaches is sufficient to maintain vertebral stability. This retrospective cohort study included 57 patients, 31 (54%) patients were treated with single-stage debridement and reconstruction with trabecular metal cages, and 26 (45.6%) patients received spine surgery without trabecular metal cages received surgery between January 2018 and March 2021 in our tertiary academic teaching hospital. The CRP values dropped borderline significantly in the TM cage group compared with the non-TM cage group postoperatively. In patients with spondylodiscitis, it is advisable to perform single-stage debridement and reconstruction with a trabecular metal cage, which allows abscess drainage and rapid mobilization, prevents deformity.

Abstract: Chemical burns are one of the most dangerous and aggressive types of burns as they can cause significant tissue damage, leading to pain, inflammation, necrosis, and scarring. We present a burn case report associated with the use of Acellular Dermal Matrix (MatriDerm® MedSkin Solution Dr. Suwelack AG, Billerbeck, Germany) for the reconstruction of a Hallux after the patient was mistakenly administered intramuscular Nitric Acid at another institution. The patient presented with a third degree burn that compromised the medial aspect of the hallux’s skin, the distal phalanx and nail bed. Early debridement was performed, and Negative Pressure Wound Therapy (NPWT VAC, 3M, US) was used to preserve and promote tissue viability. Eight days later, the patient was taken to the OR, and Acellular Dermal Matrix and split-thickness skin graft were used to reconstruct her right hallux’s defect. The patient achieved adequate clinical evolution and was discharged with complete reconstruction of the burned area. Acellular Dermal Matrix proved to be an important and viable option for reconstructive surgery after a chemical burn, and further studies are warranted to ensure its routine usage in this kind of lesions. Keywords: chemical burn, acellular matrix, hallux reconstruction, NPWT

Optical motion capture systems are prone to the errors connected with markers recognition – occlusion, leaving the scene or mislabelling – all these errors are then corrected in the software, but still, the process is not perfect, resulting in artifact distortions. In the article, we examine four existing types of artifacts, then propose the method for detection and classification of the distortions. The algorithm is based on the derivative analysis, low-pass filtering, mathematical morphology and loose predictor. The tests involved multiple simulations using synthetically distorted sequences, comparison of performance to the human operators on real life data and applicability analysis for the distortion removal.

The recent glaciation of the southern part of the Altai is estimated (1256 glaciers with the total area of 559.15±31.13 km2), the area of the glaciers of the whole Altai mountains is evaluated by 1096.55 km2. In the southern part of Altai 2276 glaciers with the total area of 1348.43±56.16 km2 were reconstructed, the first estimate of the LIA glacial area for the whole Altai mountain system is given (2288.04 km2). Since the LIA the glaciers decrease by 59% in the southern part of Altai and by 47.9% for the whole Altai. The ELA in the southern part of Altai increased averagely by 106 m. The higher changes of ELA in relatively humid areas is probably caused by decrease of precipitation. Glaciers of Tavan Bogd glacial center degraded with higher rates after 1968 relative to the interval between 1850-1968. One of the intervals of the fastest shrinkage of the glaciers in 2000-2010 was caused by unfavorable for the glaciers dry and warm interval 1989-2004. However, the fast decrease of the glaciers in 2000-2010 was mainly caused by the shrinkage or disappearance of the smaller glaciers, large valley glaciers started fast retreat after 2010.

This work presents the computation of reliable warming trends for central Australia around Alice Springs within a circle of radius 1,000 km. Between 1880 and 2011, the average warming for the centre of Australia is +0.166 ºC/century, slightly smaller than the warming of Alice Springs, that is +0.176 ºC/century. Over a shorter time between 1910 and 2011, the centre of Australia is warming +0.794 ºC/century, slightly more than the warming of Alice Springs, that is +0.719 ºC/century.

Ultrasonic sensors are inexpensive and can take measurements with high accuracy, even with simple hardware configurations, so they are used in various fields. When multiple ultrasonic sensors exist in the measurement space, crosstalk occurs due to other nodes, which causes measurement errors. Crosstalk includes not only receiving homogeneous signals from other nodes, but also overlap by other signals, and interference by heterogeneous signals. This paper proposes a method that uses frequency sweep keying modulation to be robust against overlap and a faster region-based convolutional neural networks (R-CNN)-based demodulator to reduce the interference caused by heterogeneous signals. The demodulator works by training faster R-CNN with the spectrograms of various received signals and classifying the received signals using a faster R-CNN. Experiments implementing an ultrasonic crosstalk environment showed that compared to on-off keying (OOK), phase-shift keying (PSK), and frequency-shift keying (FSK), the proposed method can implement CDMA even with shorter codes, and is robust against overlap. Compared to correlation-based frequency sweep keying, the time-of-flight error was reduced by approximately 75%. While existing demodulators did not consider heterogeneous signals, the proposed method ignored approximately 99% of the OOK and PSK signals, and approximately 79% of the FSK signals. The proposed method performs better than the existing methods and is expected to be used in various applications.

The urban heat island (UHI) is mostly due to urbanization. This phenomenon in concert with the high temperatures caused by global climate change may profoundly affect human thermal comfort, which can influence human productivity and morbidity especially in spring/summer period. The main objective of this investigation was to determine changes in degree of thermal comfort of Mexico City’s inhabitants and compare it with the physiological equivalent temperature (PET) to evaluate whether PET and its categorization are adequate to be applied in Mexico City. A series of microclimatological measurements to estimate PET were made in four sites including the city´s center. Concomitantly, a series of surveys of thermal perception were applied to 1300 passersby. The results show that PET has increased from 1990 to 2020 from 0.1208 °C/year to 0.1498 °C/year in the study sites, besides overestimating the degree of thermal comfort of people according to the stablished categories or classes. It is concluded that it is necessary to adjust thermal stress categories. Knowing the percentage of people without thermal comfort will lead us to determine different ranges in environmental parameters to define an acceptable environment for most people.

Lack of due attention to the orientation of streets and establishment of urban blocks without regard for climatic characteristics and conditions of the environment have an adverse effect on thermal comfort in open urban spaces. Construction of new settlements without taking into account climatic requirements undermines thermal comfort for pedestrians and other users, especially in cold regions. Considering the coldness of the region under study and the significance of the orientation of streets in absorbing radiation and providing heat to outdoor urban spaces, this study investigates the effect of the orientation of streets on microclimatic comfort in one of the residential towns of Hamadan City in Iran. For this purpose, microclimate simulation was performed using ENVI-met software. A residential block with four different orientations (the most common orientations of its surrounding buildings) were simulated in the coldest day of winter and the hottest day of summer. The results suggest that streets have different thermal behavior in different orientations. Orientation affects mean radiant temperature (Tmrt), the duration of exposure to direct sunlight, wind speed, and physiological equivalent temperature (PET), which are all important factors in thermal comfort. Based on these findings, north-south streets in Hamedan receive more radiant temperature during winter compared to other simulated orientations and provide more desirable thermal comfort. The average PET value on a winter day at a point on the north-south passage was 4.5-8 °C warmer than other orientations. In summer, streets with intercardinal orientations (i.e., northeast-southwest and northwest-southeast) provided the lowest PET (about 2 °C cooler than other orientations) and better thermal comfort

In this paper, an original approach allowing the determination of the iron losses in the electromagnetic devices is presented. This new approach exploits the Loss Surface (LS) hysteresis model and the magnetic flux density waveforms resulting from a generalized nonlinear adaptive magnetic equivalent circuit (MEC) using a mesh-based formulation in two-dimensional (2-D) or quasi three-dimensional (3-D). The model coupling has been applied to a 18-slots/16-poles radial-flux interior permanent-magnet (PM) synchronous machine (PMSM) dedicated to automotive applications, mainly for electric/hybrid/fuel cell vehicles (EVs/HEVs/FCVs). The obtained results have been compared with those made retrospectively in the 2-D transient finite-element (FE) Flux. The influence of the MEC discretization on the iron loss calculation and the electromagnetic performances has been analyzed. The computation time is divided by 3/2 with an error less than 7 %.

In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

Abstract: Rationale. Object tracking has significance in many applications ranging from control of unmanned vehicles to autonomous monitoring of specific situations and events, especially when providing safety for patients with certain adverse conditions such as epileptic seizures. Conventional tracking methods face many challenges, such as the need for dedicated attached devices or tags, influence by high image noise, complex object movements, and intensive com-putational requirements. We have developed earlier computationally efficient algorithms for global optical flow reconstruction of group velocities that provide means for convulsive seizure detection and have potential applications in fall and apnea detection. Here, we address the chal-lenge of using the same calculated group velocities for object tracking in parallel. Methods. We propose a novel optical flow-based method for object tracking. It utilizes real-time image se-quences from the camera and directly reconstructs global motion-group parameters of the con-tent. These parameters can steer a rectangular region of interest surrounding the moving object to follow the target. The method successfully applies to multi-spectral data, further improving its effectiveness. Results. Experimental results on simulated tests and complex real-world data demonstrate the method's capabilities. The proposed optical flow reconstruction can provide accurate, robust, and faster results compared to current state-of-the-art approaches.

A viable radiation dominated era in the early universe is best described by the standard (FLRW) model of cosmology. In this short review, we demonstrate reconstruction of the forms of F(R) in the modified theory of gravity, and the metric compatible F(T) together with the symmetric F(Q) in alternative teleparallel theories of gravity from different perspectives, primarily rendering emphasis on a viable FLRW radiation era. Inflation has also been studied for a particular choice of the scalar potential. The inflationary parameters are found to agree appreciably with the recently released observational data.

While Neural Radiance Fields (NeRF) are gaining increasing interest in various domains as innovative methods for novel view synthesis and image-based reconstruction, their potential application in the realm of Cultural Heritage remains unexplored. Purpose of this paper is to assess the effectiveness of applying NeRF to sets of images of digital heritage objects and sites. The study’s findings demonstrate that NeRF could be valuable when used in combination with or as a comparison to other well-established techniques such as photogrammetry, to expand the possibilities of preserving and presenting heritage assets with enhanced visual fidelity and accuracy. Particularly, NeRF show promising results in improving the rendering of translucent and reflective surfaces, objects with homogeneous textures, and elements with intricate details. In addition, we demonstrate that, when considering the same set of input images (with known camera poses), reducing the image quality or the number of images results in significantly less information loss with NeRF compared to photogrammetry. This suggests that NeRF is preferentially suited for scenarios involving sparse information or low-quality photos or videos, which could be especially valuable in risky or challenging situations.

Background: Computed tomography examinations have produced high radiation doses to patients, especially the CT brain. This study aimed to optimize the radiation dose and image quality in adult CT brain protocol. Materials and Methods: Images were acquired by Catphan 700 phantom. Radiation doses were recorded as CTDIvol and dose length product (DLP). CT brain protocols were optimized by varying parameters such as kVp, mAs, signal-to-noise ratio (SNR) level, and Clearview iterative reconstruction (IR). Image quality were also evaluataion by The AutoQA Plus software. Results: CT Number accuracy and linearity had a robust positive correlation with the linear attenuation coefficient (µ) and showed more inaccurate CT numbers when using 80 kVp. MTF showed a higher value in 100 and 120 kVp protocols, while high contrast spatial resolution showed a higher value in 80 and 100 kVp protocols. Low contrast detectability and CNR tended to increase when using high mAs, SNR and Clearview IR protocol. Noise decreased when using a high radiation dose and a high percentage of Clearview IR. CTDIvol and DLP were increased with increasing kVp, mAs, and SNR levels, while the increasing percentage of Clearview did not affect the radiation dose. Conclusion: Optimized protocols, including radiation dose and image quality, should be evaluated to preserve diagnostic capability. The recommended parameter settings include kVp set between 100-120 kVp, mAs ranging from 200-300 mAs, SNR level within the range of 0.7-1.0, and an iterative reconstruction value of 30% Clearview to 60% or higher.

Texture is essential information for image representation, capturing patterns, and structures. Consequently, texture plays a crucial role in the manufacturing industry and has been extensively studied in the fields of computer vision and pattern recognition. However, real-world textures are susceptible to defects, which can degrade the image quality and cause various issues. Therefore, there is a need for accurate and effective methods to detect texture defects. In this study, a simple autoencoder and Fourier transform were employed for texture defect detection. The proposed method combines Fourier transform analysis with the reconstructed template obtained from the simple autoencoder. Fourier transform is a powerful tool for analyzing the frequency domain of images and signals. Moreover, analyzing the frequency domain enables effective defect detection because texture defects often exhibit characteristic changes in specific frequency ranges. The proposed method demonstrates effectiveness and accuracy in detecting texture defects. Experimental results are presented to evaluate its performance and compare it with those of existing approaches.

As a high-quality forestry product with excellent performance, particleboard is widely used in many fields and has great market potential. At present, it is a research difficulty to accurately identify small, fine and different shapes of defects on the whole particleboard through machine vision technology. The application of image super-resolution reconstruction technology on particleboard can improve the surface image quality of particleboard, which is conducive to the subsequent improvement of defect detection accuracy. In this study, super-resolution dense attention generative adversarial network (SRDAGAN) model was improved to solve the problem that super-resolution generative adversarial network (SRGAN) reconstructed image would produce artifacts and its performance needed to be improved. The Batch Normalization (BN) layer was removed, the convolutional block attention module (CBAM) was optimized to construct dense block, and the dense blocks were constructed by densely skip connection. Then, the corresponding 52400 image blocks with high resolution and low resolution were trained, verified and tested according to the ratio of 3:1:1. The model was comprehensively evaluated from the effect of image reconstruction and the two indexes of PSNR and SSIM. It was found that compared with BICUBIC and SRGAN, PSNR index of SRDAGAN increased by 4.88dB and 3.25dB respectively, and SSIM increased by 0.0507 and 0.1122 respectively. The reconstructed images not only had clearer texture, but also had more realistic expression of various features, and the performance of the model had been greatly improved. At the same time, this study also emphatically discussed on the image reconstruction effect with defects. The result showed that the SRDAGAN proposed in this study can complete the super-resolution reconstruction of particleboard images with high quality. In the future, it can also be further combined with defect detection for actual production to improve the quality of forestry products and increase economic benefits.

We present a near real-time solution for 3D reconstruction from aerial images captured by consumer UAVs. Our core idea is to simplify the multi-view stereo problem into a series of two-view stereo matching problems. Our method applies to UAVs equipped with only one camera and does not require special stereo-capturing setups. We found that the neighboring two video frames taken by UAVs flying at a mid-to-high cruising altitude can be approximated as left and right views from a virtual stereo camera. Leveraging GPU-accelerated real-time stereo estimation, efficient PnP correspondence solving algorithms and extended Kalman filter, our system simultaneously predicts scene geometry and camera position/orientation from the virtual stereo cameras. Also, this method allows user selection of varying baseline lengths, which provides more flexibility given the trade-off between camera resolution, effective measuring distance, flight altitude, and mapping accuracy. Our method outputs dense point clouds at a constant speed of 25 frames per second and is validated on a variety of real-world datasets with satisfactory results.

Orbital fractures are a common finding in facial trauma and serious complications may arise when orbital reconstruction is not done properly. The virtual planning can be used to manufacture patient-specific titanium orbital implants (PSI) through the process of selective laser melting. This method is currently considered the most accurate technique for orbital reconstruction. Even with the most accurate tehniques of bone reconstruction, there are still situations where enophthalmos is present after reconstruction which may be produced by intraorbital soft tissue atrophy. The aim of this paper was to evaluate the orbital soft tissue after postraumatic reconstruction of the orbital walls fractures. 10 patients diagnosed with unilateral orbital fractures were included in this study. A CT scan of the head region with thin slices (0.6mm) and soft and bone tissue windows was done. After data processing, the STL files were exported and the intraorbital fat tissue volume and the muscular tissue volume were masured. The volumes of affected orbit tissues were compared with the volumes of the healthy orbit tissues for each patient. Our findings conclude that a higher or a lower grade of fat and muscular tissue loss is present in all cases of reconstructed orbital fractures.

A class of models for non-Gaussian spatial random fields is explored for spatial field reconstruction in environmental and sensor network monitoring. The family of models explored utilises a class of transformation functions known as the Tukey g-and-h transformations to create a family of warped spatial Gaussian process models which can support various desirable features such as flexible marginal distributions, which can be skewed, leptokurtic and/or heavy-tailed. The resulting model is widely applicable in a range of spatial field reconstruction applications. To utilise the model in applications in practice, it is important to carefully characterise the statistical properties of the Tukey g-and-h random fields. In this work, we both study the properties of the resulting warped Gaussian processes as well as using the characterising statistical properties of the warped processes to obtain flexible spatial field reconstructions. In this regard, we derive five different estimators for various important quantities often considered in spatial field reconstruction problems. These include the multi-point Minimum Mean Squared Error (MMSE) estimators; the multiple point Maximum A-Posteriori (MAP) estimators; an efficient class of multiple-point linear estimators based on the Spatial-Best Linear Unbiased (S-BLUE) estimators; and two multi-point threshold exceedance based estimators, namely the Spatial Regional and Level Exceedance estimators. Simulation results and real data examples show the benefits of using the Tukey g-and-h transformation as opposed to standard Gaussian spatial random fields in a real data application for environmental monitoring.

Recent years witnessed progressive broadening of the practical use of 3D-printed aluminium alloy parts, in particular for specific aerospace applications where weight saving is of great importance. Selective laser melting (SLM) is an intrinsically multi-parametric fabrication technology that offers multiple means of controlling mechanical properties (elastic moduli, yield strength, ductility) through the control over grains size, shape, and orientation. Ultimately, this approach implies that structural elements can be purposefully fabricated to reinforce specific zones and directions where higher mechanical loads are anticipated by design. Targeted control over mechanical properties is achieved through the tuning of 3D-printing parameters and may even obviate the need of heat treatment or mechanical post-processing. Systematic studies of grain structure for different printing orientation with the help of EBSD techniques in combination with mechanical testing at different dimensional levels are the necessary first steps to implement this agenda. Samples of 3D-printable Al-Mg-Si RS-333 alloy were fabricated in 3 orientations with respect to the principal build direction and the fast laser beam scanning direction. Sample structure and proper-ties were investigated using a number of techniques, including EBSD, in situ SEM tensile testing, roughness measurements and nanoindentation. The as-printed samples we found to display strong variation in Young’s modulus values from nanoindentation (from 43 to 66 GPa) and tensile tests (from 54 to 75 GPa), yield stress and ultimate tensile strength (100…195 and 130…220 MPa) in different printing orientations, and almost constant hardness of about 0.8 GPa. A further preliminary study was conducted of the effect of surface finishing on the mechanical performance. Surface polishing appears to reduce Young’s modulus and yield strength, but improves ductility, whereas the influence of sand blasting is more controversial. The experimental results are dis-cussed in connection with the grain morphology and orientation.

Inspired by the work of S. D. Odintsov and V. K. Oikonomou, Phys. Rev. D 92, 024016 (2015) [1], the present study reports a reconstruction scheme for f (R) gravity with the scale factor a(t) µ (t _* - t) _c²²describing the pre-bounce ekpyrotic contraction, where t is the big crunch time. The reconstructed f (R) is used to derive expressions for density and pressure contributions and the equation of state parameter resulting from this reconstruction is found to behave like "quintom". It has also been observed that the reconstructed f (R) has satisfied a sufficient condition for a realistic model. In the subsequent phase the reconstructed f (R) is applied to the model of chameleon scalar field and the scalar field f and the potential V(f) are tested for quasi-exponential ex pansion. It has been observed that although the reconstructed f (R) satisfies one of the sufficient conditions for realistic model, the quasi-exponential expansion is not available due to this reconstruction. Finally, the consequences pre-bounce ekpyrotic inflation i n f (R) gravity are compared to the background solution for f (R) matter bounce.

In this paper, our goal is to perform a virtual restoration of an ancient coin from its image. The present work is the first one to propose this problem, and it is motivated by two key promising applications. The first of these emerges from the recently recognised dependence of automatic image based coin type matching on the condition of the imaged coins; the algorithm introduced herein could be used as a pre-processing step, aimed at overcoming the aforementioned weakness. The second application concerns the utility both to professional and hobby numismatists of being able to visualise and study an ancient coin in a state closer to its original (minted) appearance. To address the conceptual problem at hand, we introduce a framework which comprises a deep learning based method using Generative Adversarial Networks, capable of learning the range of appearance variation of different semantic elements artistically depicted on coins, and a complementary algorithm used to collect, correctly label, and prepare for processing a large numbers of images (here 100,000) of ancient coins needed to facilitate the training of the aforementioned learning method. Empirical evaluation performed on a withheld subset of the data demonstrates extremely promising performance of the proposed methodology and shows that our algorithm correctly learns the spectra of appearance variation across different semantic elements, and despite the enormous variability present reconstructs the missing (damaged) detail while matching the surrounding semantic content and artistic style.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

In steel recycling, the optimization of electric arc furnaces (EAFs) is of central importance in order to increase efficiency and reduce costs. This study focuses on the optimization of electric arcs, which make a significant contribution to the energy consumption of EAFs. A three-phase equivalent circuit integrated with the Cassie-Mayr arc model is used to capture the nonlinear and dynamic characteristics of arcs, including arc breakage and ignition process. A particle swarm optimization technique is applied to real EAF data containing current and voltage measurements to estimate the parameters of the Cassie-Mayr model. A novel Arc Quality Index (AQI) is introduced in the study, which can be used to evaluate arc quality based on deviations from optimal conditions. The AQI provides a qualitative assessment of arc quality, analogous to indices such as arc coverage and arc stability. The study concludes that the AQI serves as an effective operational tool for EAF operators to optimize production and increase the efficiency and sustainability of steel production. The results underline the importance of understanding electric arc dynamics for the development of EAF technology.

Meat loss and waste are estimated at each stage along the food chain, but the methods used are complex and the data needed often fragmented. We, therefore, evaluated the feasibility of estimating meat loss and waste using a simpler method comparing meat availability and consumption, using Swiss meat consumption according to a national nutrition survey and Swiss meat availability according to food balance sheets. As availability is reported at the fresh meat level and consumption as consumed, items of the latter were converted to fresh meat equivalents before comparing consumption with availability. Consumed unprocessed meat was directly converted to fresh meat equivalents and consumed meat products after having identified their meat ingredients. Meat availability, meat consumption as consumed and as fresh meat equivalent were 138.4 g/d, 105.5 g/d, and 112.1 g/d, respectively. The resulting total meat loss and waste was 19% and varied from −36% to 38% for the different meat types. Estimating meat loss and waste based on meat availability and consumption derived from a national nutrition survey yielded results varying to such an extent that the evaluated method to estimate meat loss and waste cannot be recommended.

Seasonal snowpacks, characterized by their snow water equivalent (SWE), play a major role in the hydrological cycle, snow melt contributions to floods and the subsequent availability of water resources downstream. Accurately estimating SWE and understanding its spatial and temporal variations presents a considerable challenge, particularly within mountainous regions characterized by complex terrain and limited observational data. Seeking to enhance the performance of the widely used Soil and Water Assessment Tool (SWAT), we report a new approach characterising snowpack behaviour incorporating both modelled and remotely sensed derived SWE calibration data. We focus on the Chenab River Basin (CRB) a headwater catchment of the Indus Basin, globally significant in terms of human inhabitants and intensifying flood risk due to climate change. We conducted a thorough assessment of five satellite-derived and reanalysis-based precipitation datasets: ERA5-Land, CMORPH, TRMM, APHRODITE, and CPC UPP. This reveals significant levels of uncertainty in global precipitation products when compared to reference data from observed stations as well as in the resulting simulated streamflow from the SWAT model. Subsequently, we expanded the scope of the SWAT model to encompass the spatial and temporal simulation of SWE. This was achieved by incorporating information from remotely sensed and modelled SWE products, manually adjusting snow parameters in R-SWAT for both the main basin and at sub-basin scales. Integrating SWE from reference snow products into the calibration process, alongside streamflow data, substantially enhanced modelling accuracy to simulate SWE compared to the conventional auto-calibration and single-variable approaches reliant solely on streamflow data. This approach results in considerable improvement in SWE predictions and to some extent in streamflow simulation in catchments dominated by snow. This research highlights the potential of remote sensing and modelled SWE parameterisation in the absence of in-situ snowpack data in high-altitude environments. An improved understanding of SWE behaviour is vital for predicting hydrological responses spanning hazards to water resources in the populous downstream regions of the Indus Basin, especially in the face of climate change.

The decreasing width, increasing aspect ratio RDL presents significant challenges to design for reliability (DFR) of advanced package. Therefore, this paper proposes a ML based RDL modeling and simulation method. In the method, RDL is divided into blocks and subdivided into pixels of metal percentage, and the RDL is digitalized as tensors. Then, an ANN-based surrogate model is built and trained by a subset of tensors to predict the equivalent material properties of each block. Lastly, all blocks are transformed into elements for simulations. For validation, line bending simulations were conducted on an RDL, with the reaction force as accuracy indicator. The results show that neglecting layout impact causes critical errors as substrate thins. By the method, the reaction force error is 2.81% and the layout impact can accurately be considered with 200×200 elements. For application, the TCT maximum temperature state simulation was conducted on a CPU chip. The simulation indicates that for advanced package the maximum stress more likely occurs in RDL rather than bumps, both RDL and bumps are critical impacted by layouts, and RDL stress is also impacted by vias/bumps. The proposed method precisely concerns layout impacts with little resources, presents an opportunity of efficiency improvement.

The study of fractures in the subsurface is very important in unconventional reservoirs since they are the main conduits for hydrocarbon flow. For this reason, a variety of equivalent medium theories have been proposed for the estimation of fracture and fluid properties within reservoir rocks. We experimentally investigated the feasibility of applying the Galvin model in fractured tight stones. For this proposal, three artificial fractured tight sandstone samples with the same background porosity (11.7% ± 1.2%) but different fracture densities of 0.00, 0.0312, and 0.0624 were manufactured. The fracture thickness was 0.06 mm and the fracture diameter was 3 mm in all the fractured samples. Ultrasonic P- and S-wave velocities were measured at 0.5 MHz in a laboratory setting in dry and water-saturated conditions in directions at 0°, 45°, and 90° to the fracture normal. The results were compared with theoretical predictions of the Galvin model. The comparison showed that model predictions significantly underestimated P- and S- wave velocities as well as P-wave anisotropy in water-saturated conditions, but overestimated P-wave anisotropy in dry conditions. By analyzing the differences between the measured results and theoretical predictions, we modified the Galvin model by adding the squirt flow mechanism to it and used the Thomsen model to obtain the elastic moduli in high- and low-frequency limits. The modified model predictions showed good fits with the measured results.

Season plays a key role in the development of outdoor spaces for pedestrians in hot humid cities. This research studies the influence of seasonal variations on pedestrian thermal comfort on the pedestrian level by means of meteorology and field observations of selected footpaths in the major tourist area of Malacca. This experiment was carried out on selected clear calm days indicative of each season during the development of a research project, and hourly meteorological transects from 10:00 am to 6:00 pm and questioned 200 respondents on their thermal awareness, comfort, and preferences were conducted. Adaptation, thermal comfort vote, thermal preference, age, season and hour of the day were significant non-meteorological factors, apart from meteorological information. The findings of analyzes showed that the thermal experience and expectation existed and in different seasons people changed perceptions for the outside thermal environment. Almost 80% local tourist and 55 % international tourist was accepted Physiologically Equivalent Temperature (PET) range affected by the local climate and thermal adaptation. The subjective thermal sensation on physiological equivalent temperature generated an acceptable physiological equivalent temperature of 32.6°C to 36.8°C based on the seasonal variations for Malacca tourist zone in Malaysia. These findings shed light on the optimal design of outdoor spaces for increasing the utilization rate. The seasonal variation must be taken into account so that the outdoor landscape design provides more opportunities for different seasons to communicate with the atmosphere and so enhance thermal comfort and utilization.

This empirical study investigates large urban park cooling effects on the thermal comfort of occupants in the vicinity of the main central park, located in Madrid, Spain. Data were gathered during hot summer days, using mobile observations and a questionnaire. The results showed that the cooling effect of this urban park of 140 ha area at a distance of 150 m is able to reduce temperature by an average of 0.63°C and 1.28°C for distances of 380 m and of 665 meters from the park. Moreover, the degree of the Physiological Equivalent Temperature (PET) index at a distance of 150 meters from the park is on average 2°C PET and 2.3°C PET less compared to distances of 380 m and 665 m, respectively. Considering distance from the park, the correlation between occupant Perceived Thermal Comfort (PTC) and PET is inverse. That is, augmenting the distance from park increases PET, while the extent of PTC reduces accordingly. The correlation between these two factors at the nearest and furthest distances from the park is meaningful (P-value <0/05). The results also showed that large-scale urban parks generally play a significant part in creating a cognitive state of high-perceived thermal comfort spaces for residents.

The eddy current loss should be optimized to be as less as possible for the stability of permanent magnet in high speed permanent magnet synchronous motor (HSPMSM) rotor and ensure the high efficiency and low temperature of the motor. This paper analyzes the eddy current distribution in rotor, with consideration of the conflict of the thickness of sleeve and diameter of the rotor, calculating the eddy current loss (ECL) and the thermal distribution via Separation of variables method for solving Maxwell's equations with analytical hieratical model of ECL constructed. The optimization result of ECL of the HSPMSM whose power and rated speed is 30kw 48000r/min can be got by multi-objective optimization method, combined weighting coefficient method and traversal algorithm based on chaotic local search particle swarm optimization (CLSPSO), utilizing ECL analytical model and other analytical constraints. Related experiment and measurement has been implemented with new approach of loss separation.

In the context of intelligent and integrative lighting, in addition to the need for color quality and brightness, the non-visual effect is essential. This refers to the retinal ganglion cells (ipRGCs) and their function, first proposed in 1927. The melanopsin action spectrum has been published in CIE S 026/E: 2018 with the corresponding melanopic equivalent daylight (D65) illuminance (mEDI), melanopic daylight (D65) efficacy ratio (mDER) and 4 other parameters. Due to the importance of mEDI and mDER, this work synthesizes a simple computational model of mDER as the main research objective, based on a database of 4214 practical spectral power distributions (SPDs) of daylight, conventional, LED, and mixed light sources. In addition to the high correlation coefficient R2 of 0.96795 and the 97% confidence offset of 0.0067802, the feasibility of the mDER model in intelligent and integrated lighting applications has been extensively tested and validated. The uncertainty between the mEDI calculated directly from the spectra and that obtained by processing the RGB sensor and applying the mDER model has reached ± 3.3% after an appropriate matrixing process and proper illumination characterization combined with the successful mDER calculation model. This result opens the potential of low-cost RGB sensors for applications in intelligent and integrative lighting systems to optimize and compensate the non-visual effective parameter mEDI using daylight and artificial light in indoor spaces. The goal of the research on RGB sensors and the corresponding processing method are also presented and their feasibility is methodically demonstrated. A comprehensive investigation with a huge amount of color sensor sensitivities is necessary in a future work of other researches.

Urinary tract diseases are common in cats, and often require surgical reconstruction. Here, to explore the possibility of urinary tract reconstruction in cats using in-vivo tissue architecture (iBTA), biosheets fabricated using iBTA technology were implanted into the feline bladder and the regeneration process was histologically evaluated. The biosheets were prepared by embedding molds into the dorsal subcutaneous pouches of six cats for 2 months. A section of the bladder wall was removed, and the biosheets were sutured to the excision site. After 1 and 3 months of implantation, the biosheets were harvested and evaluated histologically. Implantable biosheets were formed with a success rate of 67%. There were no major complications following implantation, including tissue rejection, severe inflammation, or infection. Urinary incontinence was also not observed. Histological evaluation revealed the bladder lumen was almost entirely covered by urothelium after 1 month, with myofibroblast infiltration into the biosheets. After 3 months, the urothelium became multilayered, and mature myocytes and nerve fibers were observed at the implantation site. In conclusion, this study showed that tissue reconstruction using iBTA can be applied to cats, and that biosheets have the potential to be useful in both the structural and functional regeneration of the feline urinary tract.

Background. Cervical esophageal reconstruction is vital for improving the quality of life in cancer surgery patients. Microsurgery is crucial, providing vascularized tissue for defect repair, particularly in secondary cases with a higher risk of failure due to larger defects and damage from previous surgery and radiotherapy. The purpose of this study was to describe the clinical characteristics of a series of patients who underwent secondary repair of esophageal defects and provide practical information for the management and treatment of such cases based on the authors' experience and the literature review. Methods. We retrospectively reviewed the electronic medical records of the Plastic Surgery Clinic at the University of Trieste to identify cases of patients who underwent secondary esophageal microsurgical reconstructions following oncological surgery. Patient demographics, etiology of esophageal defects, previous surgical history, and preoperative assessments were collected from medical records. Surgical techniques employed for reconstruction, such as pedicled flaps or free tissue transfers, were documented along with intraoperative details. Postoperative outcomes, including complications, graft viability, and functional outcomes, were evaluated during follow-up. Results. We treated 13 cases of secondary esophageal reconstructions from 2011 to 2022. Most commonly, Antero-Lateral Thigh (ALT) flaps were used in 10 cases, while 2 cases employed Radial Forearm Flap (RFF), and 1 a chimeric parascapular flap. No flap failures occurred during a median 50-month follow-up. One ALT flap patient experienced post-op stricture but maintained swallowing ability. A single tracheoesophageal fistula occurred in a RFF patient with a history of radiotherapy and completion lymph node dissection. Conclusions. Cervical esophageal reconstruction significantly impacts patients' quality of life by restoring oral feeding and phonation. When local flaps fall short, microsurgical reconstruction with intestinal flaps is valuable, but burdened by limitations. For challenging secondary cases, ALT or RFF flaps emerge as safer options due to their robust pedicles, yielding low complication rates and positive functional outcomes.

Background: Anthropometric measurements play a crucial role in medico-legal practices. Actually, several scanning technologies are employed in post-mortem investigations for forensic anthropological measurements. This study aims to evaluate the precision, in-ter-rater reliability, and accuracy of a hand-held scanner in measuring various body parts. Methods: Three independent raters measured seven longitudinal distances using an iPad Pro equipped with a LiDAR sensor and specific software. These measurements were sta-tistically compared to manual measurements conducted by an operator using a laser level and a meterstick (considered the gold standard). Results: The Friedman’s test revealed minimal intra-rater variability in digital measurements. Inter-rater variability analysis yielded an ICC=1, signifying high agreement among the three independent raters. Addi-tionally, the accuracy of digital measurements displayed errors below 2%. Conclusions: Preliminary findings demonstrate that the pairing of LiDAR technology with the Polycam app showcases high precision, inter-rater agreement, and accuracy. Hand-held scanners show potential in forensic anthropology due to their simplicity, affordability, and porta-bility. However, further validation studies under real-world conditions are essential to es-tablish the reliability and effectiveness of handheld scanners in medico-legal settings.

Accidents between right-turning commercial vehicles and crossing vulnerable road users (VRU) in urban environments often lead to serious or fatal injuries and therefore play a significant role in forensic accident analysis. To reduce the risk of accidents, blind spot assistance systems have been installed in commercial vehicles for several years, among other things, to detect VRUs and warn the driver in time. However, since such systems cannot reliably prevent all turning accidents, an investigation by experts must clarify how the accident occurred and to what extent the blind spot assistance system influenced the course of the accident. The occurrence of the acoustic warning message can be defined as an objective reaction prompt for the driver, so that the blind spot assistance system can significantly influence the avoidability assessment. In order to be able to integrate the system into forensic accident analysis, a precise knowledge of how the system works and its limitations is required. For this purpose, tests with different systems and accident constellations were conducted and evaluated. It was found that the type of sensor used for the assistance systems has a great influence on the system’s performance. The lateral distance between the right side of the commercial vehicle and the VRU as well as obstacles between them and the speed difference can take great influence on the reliability of the assistance system. Depending on the concrete time of the system’s warning signal the accident can be avoided or not by the driver when reacting on this signal.

Compton cameras detect scattered gamma rays and estimate the distribution of gamma-ray sources. Nonetheless, crafting a camera tailored to a specific application presents formidable challenges, often necessitating the implementation of diverse image reconstruction techniques. Delving into the factors influencing these cameras can pave the way for design optimization and performance enhancement. This study introduces an inventive detector design for Compton imaging systems, building upon the achievements of prior designs. The proposed system contains eight scatterer detectors and a semiconductor absorber detector, spaced at 1 mm and 30 mm intervals, respectively. The source-to-first-scatterer-detector distance is 5 mm, with scatterer and absorber detector plates measuring 70× 70× 2.125 mm³ and 70× 70× 10 mm³, respectively. Geant4 simulation toolkit models the Compton imaging system, and an analytical method reconstructs Compton camera images. Unlike more straightforward techniques, the analytical method directly reconstructs Compton camera images by solving the equation relating to the reflected image data. This approach is implemented in the C++ programming language. The study's findings reveal that the analytical method discerns optimal conditions and parameters that significantly influence efficiency, yielding a full width at half maximum (FWHM) of 3.7 mm with an angular uncertainty of approximately 2.7 degrees at an energy level of 0.662 MeV. Compared to another experimental design employing the analytical image reconstruction approach, the FWHM value decreased by 0.7 mm. This study presents an innovative detector design and an analytical reconstruction method for Compton imaging systems, showcasing improved efficiency and accuracy.

The scalp is a unique anatomical region with distinct challenges for reconstruction, especially in cases of melanoma excision. This study explores the utilization of the O-Z flap technique as an alternative approach for patients with melanoma, where traditional free flap reconstruction may not be feasible due to age or underlying health conditions. However, in this case, the patient had a history of angina and was unwilling to undergo a long operation due to his advanced age. This study highlights the importance of following NCCN guidelines for melanoma resection margins based on tumor thickness and underscores the value of staged resection planning to minimize deficits. This requires an individualized approach as each patient may have different circumstances (general health condition, age, compliance, etc.). So we planned a staged excision first. In the first surgery, we would resect the tumor minimally and then determine the exact size of the tumor. Then, in the second surgery, we resected it with a safety margin according to the guidelines. The O-Z flap, a local flap with an "O"-shaped defect and "Z"-shaped incision line, is introduced as a reconstructive option. The surgical procedure, advantages, and limitations of this approach are discussed. This study provides valuable insights into achieving successful scalp reconstruction while considering aesthetic outcomes and patient-specific factors.

The need for continuous research to refine the models used in accident reconstruction appears with the development of new car models that satisfy consumer complaints. The paper analyzed a sub-sequence of car and pedestrian accidents, from the perspective of the distance traveled by them in the contact phase, with the aim of improving the information regarding the reconstruction of road accidents. The research included the analysis of some accidents with pedestrian dummies, as well as the simulation of the impact between different classes of vehicles and pedestrians in two different walking positions. Specialized software was used with complex multibody models of pedestrians, modifying the speed and deceleration parameters at the time of the collision. The research results highlight the differences between bilinear models used in accident reconstruction and the proposed study. They can also be used to determine the distance traveled by the vehicle in the first phase of the collision with pedestrians.

Resection of malignant lesions in the oral and maxillofacial area causes functional and morphological defects. To recover from these defects, reconstruction surgery is needed such as a primary closure or a flap. There are advantages and disadvantages to the method of using the primary closure and the flap, and the choice of procedure is entirely up to a surgeon. The purpose of this study is to evaluate availability of primary closure in patients. For 10 years from January 2010 to May 2020, patients who recovered using flaps after removing malignant lesions from the oral cavity and those who closed the lesion using primary closure were investigated. The investigation was conducted by searching the database of the hospital. There were 85 patients who removed malignant lesions in the oral and maxillofacial area, and among them 16 patients closed the soft tissue defects using primary closure. Operation time, histologic types, stages, wound status, and period of hospitalization according to the patients' medical records were investigated retrospectively. Between the staging and the primary closure, statistically significant differences were observed between stage I and stage II patients in 13 patients using the primary closure. (P=0.046). Statistically significant differences were identified between operation time and primary closure, with an average of 4.02 hours (P=0.015). The average period of hospitality for patients who underwent primary closure was 13.4 days, compared to 26.7 days for those who underwent flap surgery. This difference was statistically significant (P=0.0003). This study evaluated the use of primary closure in patients who underwent resection of malignant lesions in the oral and maxillofacial area. Although the majority of patients underwent reconstruction with flaps, our results showed that primary closure can be a viable option for certain patients with early-stage lesions. Therefore, oral and maxillofacial surgeons should carefully consider various evaluation criteria and select appropriate reconstruction methods to optimize functional and aesthetic outcomes for each patient.

There has been considerable research on reconstructing 3D shapes from single-view images; however, preserving the detailed information of the input image remains difficult. In this paper, we propose the application of a gradient map to train a network, aimed at improving the visual quality of fine-grained details such as the thin and tiny components of generated shapes. Each gradient map was created from the original voxel data, and each value represented the amount of information per volume. Here, the gradient map was defined by several methods that mathematically quantify and represent the detailed structure of an object. By applying this map to the loss function in training, we could induce the network to intensively train partial details, such as thin and narrow parts. We demonstrated that the detailed information was well-recovered when a weight that is proportional to the gradient value was applied to the loss. Furthermore, it is expected that our method will contribute to the development of 3D technologies related to the construction of virtual space for simulation and new customer experience.

Single cell RNA-seq (scRNA-seq) profiles conceal temporal and spatial tissue developmental information. De novo reconstruction of single cell temporal trajectory has been fairly addressed, but reverse engineering single cell 3D spatial tissue localization is hitherto landmark based, and de novo spatial reconstruction is a compelling computational open problem. Here we show that a new algorithm - named D-CE - for coalescent embedding of single cell transcriptomic networks can address this open problem. We rely merely on the spatial information encoded in the expression patterns of developmental signal transcription factor (DST) genes, and we find that D-CE of cell-cell association DST-transcriptomic networks reliably reconstructs the Geo-seq or single cell samples’ 3D spatial tissue distribution. Comparison to the novoSpaRC and CSOmap (recent and only available de novo 3D spatial reconstruction methods) on 16 datasets and 681 reconstructions, reveals a significantly distinctive superior performance of D-CE.

This paper investigated building data from multispectral and single-photon Lidar systems. The multispectral datasets from the individual channels and fused channels were explored. The multispectral and single-photon Lidar data were compared across multiple aspects: the data acquisition geometry, number of echoes, intensity, density, resolution, data defects, noise level, and the absolute and relative accuracy. In addition, we explored the performance of the multispectral and single-photon data for roof plane detection for eight complex/stylish buildings to investigate the suitability of these data for 3D building reconstruction. The building data from the single-photon and multispectral Lidar systems were evaluated with respect to the reference building vector data with an accuracy of better than 5 cm. The advantages and disadvantages of both technologies and their applications in the urban building environment are discussed.

Many classic visual monocular SLAM systems have been developed over the past decades, however, most of them will fail when dynamic scenarios dominate. DM-SLAM is proposed for handling dynamic objects in environments based on ORB-SLAM. The article mainly concentrates on two aspects. Firstly, DLRSAC is proposed to extract static features from the dynamic scene based on awareness of nature difference between motion and static, which is integrated into initialization of DM-SLAM. Secondly, we design candidate map points selection mechanism based on neighborhood mutual exclusion to balance the accuracy of tracking camera pose and system robustness in motion scenes. Finally, we conduct experiments in the public dataset and compare DM-SLAM with ORB-SLAM. The experiments verify the superiority of the DM-SLAM.

Recent advances in open data initiatives allow us to free access to a vast amount of open LiDAR data in many cities. However, most of these open LiDAR data over cities are acquired by airborne scanning, where the points on façades are sparse or even completely missing due to the viewpoint and object occlusions in the urban environment. Integrating other sources of data, such as ground images, to complete the missing parts is an effective and practical solution. This paper presents an approach for improving open LiDAR data coverage on building façades by using point cloud generated from ground images. A coarse-to-fine strategy is proposed to fuse these two different sources of data. Firstly, the façade point cloud generated from terrestrial images is initially geolocated by matching the SFM camera positions to their GPS meta-information. Next, an improved Coherent Point Drift algorithm with normal consistency is proposed to accurately align building façades to open LiDAR data. The significance of the work resides in the use of 2D overlapping points on the outline of buildings instead of limited 3D overlap between the two point clouds and the achievement to a reliable and precise registration under possible incomplete coverage and ambiguous correspondence. Experiments show that the proposed approach can significantly improve the façades details of buildings in open LiDAR data and improving registration accuracy from up to 10 meters to less than half a meter compared to classic registration methods.

This study provides a unique procedure for validating and reconstructing temperature and precipitation data. Although developed from data in Middle Italy, the validation method is intended to be universal, subject to appropriate calibration according to the climate zones analysed. This~research is an attempt to create shared applicative procedures that are most of the time only theorized or included in some software without a clear definition of the methods. The purpose is to detect most types of errors according to the procedures for data validation prescribed by the World Meteorological Organization, defining practical operations for each of the five types of data controls: gross error checking, internal consistency check, tolerance test, temporal consistency, and~spatial consistency. Temperature and~precipitation data over the period 1931--2014 were investigated. The~outcomes of this process have led to the removal of 375 records (0.02%) of temperature data from 40 weather stations and 1286 records (1.67%) of precipitation data from 118 weather stations, and 171 data points reconstructed. In conclusion, this work contributes to the development of standardized methodologies to validate climate data and provides an innovative procedure to reconstruct missing data in the absence of reliable reference time series.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

With the widespread application of Voltage Source Converter (VSC) in the power system with high penetration of renewable resources, the problem of wideband oscillations caused by the interaction between the power converters and the power grid has drawn large attention. This paper presents a new methodology for simplifying the mathematical derivations of the impedance model of VSC. Using the new simplified model, the stability and the spectrum characteristic of the performance of the VSC can be clearly analyzed. The proposed second-order d-q impedance model of the grid connected VSC at presence of PLL, not only mathematically proves that the wideband oscillatory modes always occurs in conjugate pairs, but also deliver a clear vision of the physical essence of the wideband oscillations. The classic modal analysis is executed in the paper to demonstrate the stability and frequency spectral characteristics of the wideband oscillations in the VSC integrated system. The impact of control parameters of the VSC on the wideband oscillatory stability is thouroughly analyzed using the results of the modal analysis. The methodology can be considered a powerful tool for the control design of VSC in the modern power system.

Mammography is the gold standard for breast cancer screening and diagnostic imaging; however, there is an unmet clinical need for complementary methods to detect lesions not characterized by mammography. Far-infrared 'thermogram' breast imaging can map the skin temperature, and signal inversion with components analysis can be used to identify the mechanisms of thermal image generation of the vasculature using dynamic thermal data. This work focuses on using dynamic infrared breast imaging to identify the thermal response of the stationary vascular system and the physiologic vascular response to a temperature stimulus affected by vasomodulation. The recorded data is analyzed by converting the diffusive heat propagation into a virtual wave and identifying the reflection using component analysis. Clear images of passive thermal reflection and thermal response to vasomodulation were obtained. Validation of this proposed paradigm through further clinical exploration may demonstrate clinical utility for the IR modality in diagnostic imaging, offering a potential solution to the current unmet clinical need.

The accurate wellbore pressure control not only prevents from lost circulation/blowout and fracturing formation by managing density of drilling fluid, but also improves productivity by mitigating reservoir damage. The geothermal pressure calculated by constant parameters for geothermal well would bring big error easily, as the changes of physical, rheological and thermal properties of drilling fluids with temperature were neglected. This paper researches the wellbore pressure coupling by calculating the temperature distribution with existed model, fitting the rule of density of drilling fluid with temperature and establishing mathematical models to stimulate the wellbore pressures, which is expressed as the variation of Equivalent Circulating Density (ECD) under different conditions. With this method, temperature and ECDs in the wellbore of the first medium-deep geothermal well ZK212 Yangyi Geothermal Field in Tibet were determined, and the sensitivity analysis was simulated by assumed parameters, i.e. circulating time, flow rate, geothermal gradient, diameters of wellbore, rheological models and regimes, the results indicated the geothermal gradient and flow rate were the most influence parameters on the temperature and ECD distribution, and additives added in drilling fluid should be careful which would change the properties of drilling fluid and induce the temperature redistribution. To make sure the safe drilling, velocity of pipes tripping into the hole, depth and diameter of wellbore are considered to control the surge pressure.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

We present a novel method for interpolating univariate time series data. The proposed method combines multi-point fractional Brownian bridges, a genetic algorithm, and Takens’ theorem for reconstructing a phase space from univariate time series data. The basic idea is to first generate a population of different stochastically interpolated time series data, and secondly, to use a genetic algorithm to find the pieces in the population which generate the smoothest reconstructed phase space trajectory. A smooth trajectory curve is hereby found to have a low variance of second derivatives along the curve. For simplicity, we refer to the developed method as PhaSpaSto-interpolation, which is an abbreviation for phase-space-trajectory-smoothing stochastic interpolation. The proposed approach is tested and validated with a univariate time series of the Lorenz system, five non-model data sets and tested against a cubic spline interpolation and a linear linear interpolation. We find that the criterion for smoothness guarantees low errors on known model and non-model data. Finally, we interpolate the discussed non-model data sets, and show the corresponding improved phase space portraits. The proposed method is useful for interpolating low-sampled time series data sets for, e.g., machine learning, regression analysis, or time series prediction approaches.

A finite element model of 100m X-BOW polar exploration cruise is established. The entire ship frequency response analysis was carried out, comparing the simulated values with the test values, the maximum error is 22%, but only 0.24mm/s difference, the error can be ignored from the perspective of comfort, therefore, the simulation results meet the requirements of engineering accuracy and verify the effectiveness of the model. According to the solution method for global modal equivalent mass, combing the spatial distribution principle of local modal mass, the method for solving the equivalent mass of a single local mode in mixed mode is proposed, the equivalent mass of the local vibration region of 100m X-BOW polar exploration cruise ship is solved by this method, tuned mass dampers mass ratio parameters are calculated using the equivalent mass. According to the analysis, tuned mass dampers has 31dB vibration absorption effect at 13.4Hz when the mass ratio is 0.05, it also has certain control effect at 10Hz and 18.8Hz, the control effect is 3dB and 2dB respectively, the overall control frequency band is flat and robust.

Scaling up the production of power devices involves, in the semiconductor industry, the use of large semiconductor 8” and 12” wafers of Si or SiC. Their use implicates a successful an effective monitoring and control of wafer warpage, as the geometrical size of the substrate increases, as well as a command control on the degeneration of non-linear warpage into critical phenomena known as bifurcation or buckling.To mitigate the warpage, the use of taiko wafers, which consists of wafers having a thicker region on the rim region of the wafer, has been generally adopted in the production lines. In a previous work [1] we investigated the warpage of taiko wafers by introducing the concept of equivalent thickness, in the linear approximation, for the case of a front side metalized taiko wafer. However, as the thickness of the central semiconductor substrate region decreases the possibility that also the taiko wafer bifurcates emerges. For this reason, in this work we have investigated the occurrence of bifurcation or buckling in a taiko wafer. In particular, we implemented a finite element analysis method by using ANSYS Mechanical Enterprise 2023/R2 to investigate the phenomenon of bifurcation in a taiko wafer. The investigated system consisted of a 200 mm Si (001) front side metalized (FSM) taiko wafer, having a substrate thickness ranging from 100 µm to 400 µm, with a step height fixed to 450 µm. The FSM layer consisted of an Al layer of 4.5 µm thin. The system was subjected to a thermal load such that, getting cooled from a nominal temperature T to 25°C, the metal layer can develop a residual stress. To investigate the bifurcation, an asymmetry was induced in the system by applying a slight force on a point of the circumferential region perpendicularly to the substrate. The temperature investigated ranged from 30 °C to 170 °C. From this investigation, it results that also the bifurcation is mitigated by the taiko structure. Indeed, the bifurcation emerges at higher values of the stresses with respect to the case of flat wafers having the same size and thickness of the substrate. Moreover, the concept of equivalent thickness needs to be reformulated by taking into account of the bifurcation phenomenon. Indeed, from the warpage at the bifurcation point of the taiko wafer, we can determine an overall equivalent thickness of the taiko wafer.

This article addresses the challenge of simulating rainstorm waterlogging in urban-scale areas where reliable drainage pipe network data is often lacking. Despite existing methods attempting to tackle this issue, there remains a gap in effectiveness. We present a novel approach, the Modified Equivalent Infiltration (MEI) method, building upon the foundation of the Equivalent Infiltration (EI) method. The study focuses on the outer ring area of Shanghai, utilizing data from the "In-Fa" typhoon period for simulation and comparison. Our findings reveal that the MEI method, requiring the same data inputs as the EI method, surpasses its predecessor in both principle and simulation results. Additionally, the MEI method demonstrates robustness in handling rainstorm waterlogging scenarios.

Revealing the multidimensional value of cultivated land resources, improving calculation methods, and exploring their spatial distribution characteristics and influencing factors are crucial for the enhancement of natural resource accounting system and the protection of cultivated land resources. This study take Guangxi, China as an example and construct a comprehensive multidimensional value evaluation system for cultivated land resources at the county scale. The income capitalization method, substitution market method, and value equivalent correction method were applied to calculate the economic, social, and ecological values of cultivated land resources in 111 counties. Furthermore, spatial autocorrelation analysis was employed to study their distribution characteristics and influencing factors. The results show that: (1) The total value of cultivated land resources in Guangxi reach 19,729.2 billion yuan, and the average cultivated land value is 5.3511 million yuan/hm2, of which the ratio of economic, social and ecological values is about 6:1:2; (2) The value of cultivated land has a certain distribution pattern in the global space, and the average economic and social value show the spatial distribution patterns of "low in the west and high in the east" and "low in the northwest and high in the southeast" respectively."(3) There is a significant spatial clustering effect of all values of cultivated land resources in local space, with "high-high" and "low-low" clustering. (4) Economic development level is significantly negatively correlated with the ecological value of cultivated land, while has a significant positive correlation with social value; (5) Natural conditions, economic development and agricultural development approaches are the key factors affecting the value of cultivated land resources.

The variation of mutual inductance and load parameters will affect the transmission power and efficiency of the inductive power transfer (IPT) system. The identification of mutual inductance and load parameters is an essential part of establishing a stable and reliable IPT system. This paper presents a joint identification method of load and mutual inductance for LCC-S IPT system, which does not require the establishment of primary and secondary communication and related control. Firstly, the resistance-inductance characteristics of the equivalent load of the rectifier are analyzed by simulation, and then the rectifier and system load are equivalent to the circuit model of resistance and inductance in series. Secondly, the characteristics of the reflected impedance are analyzed, and the functional relationship between the transmitter impedance and the rectifier impedance is established by using the ratio of the real part to the imaginary part of the reflected impedance, which realizes the decoupling of the load and the mutual inductance. Thirdly, the functional relationship between the equivalent impedance of the rectifier and the load resistance of the system is obtained by data fitting. Then, the equations of the above two functional relationships are combined. By measuring the voltage of the parallel compensation capacitor at the transmitting side, the current of the transmitting coil and the phase difference between the two, the battery load can be solved first, and then the mutual inductance can be calculated, so that the high-precision identification of the load and mutual inductance can be realized. Finally, an experimental platform of LCC-S IPT system is built for experimental verification. The experimental results show that the maximum identification errors of mutual inductance and load are 5.20 % and 5.53 %, respectively, which proves that the proposed identification method can achieve high precision identification.

Accurate evaluation of health status of lithium-ion batteries must be deemed as of great significance, insofar as utility and safety of batteries are of concern. Lithium plating, in particular, is notoriously known to be a chemical reaction that can cause deterioration in, or even fatal hazards to, the health of lithium-ion batteries. Electrochemical impedance spectroscopy (EIS), which has distinct advantages such as fast or non-destructive over its competitors, suffices in detecting lithium plating and thus has been attracting increasing attention in the field of battery management, but its ability of assessing quantitatively the degree of lithium plating remains largely unexplored hitherto. On this point, this work seeks to narrow that gap, by proposing an EIS-based method that can quantify the degree of lithium plating. The core conception is to eventually circumvent the reliance on state-of-health measurement, and use instead the impedance spectrum, to acquire an estimate on battery capacity loss. To do so, the effects of solid electrolyte interphase formation and lithium plating on battery capacity must be first decoupled, so that the mass of lithium plating can be quantified. Then, based on an impedance spectrum measurement, the parameters of the fractional equivalent circuit model (ECM) of the battery can be identified. These fractional ECM parameters are received as inputs by an artificial neural network, which is tasked to establish a correspondence between the model parameters and the mass of lithium plating. The empirical part of the work revolves around the data collected from an aging experiment, and the validity of the proposed method is truthfully attested by dismantling the batteries, which is otherwise not needed during the actual uptake of the method.

Falling snow alters its own microwave signatures when it begins to accumulate on the ground, making retrieval of snowfall challenging. This paper investigates the effects of snow-cover depth and cloud liquid water content on microwave signatures of terrestrial snowfall using reanalysis data and multi-annual observations by the Global Precipitation Measurement (GPM) core satellite with particular emphasis on the 89 and 166 GHz channels. It is found that over shallow snow cover (snow water equivalent (SWE) ≤ 100 kg m^-2) and low values of cloud liquid water path (LWP 100–150 g m^-2), the scattering of light snowfall (intensities ≤ 0.5 mm h⁻¹) is detectable only at frequency 166 GHz, while for higher snowfall rates, the signal can also be detected at 89 GHz. However, when SWE exceeds 200 kg m^-2 and the LWP is greater than 100–150 g m^-2, the emission from the increased liquid water content in snowing clouds becomes the only surrogate microwave signal of snowfall that is stronger at frequency 89 than 166 GHz. The results also reveal that over high latitudes above 60°N where the SWE is greater than 200 kg m^-2 and LWP is lower than 100–150 g m^-2, the snowfall microwave signal could not be detected with GPM without considering a priori data about SWE and LWP. Our findings provide quantitative insights for improving retrieval of snowfall in particular over snow-covered terrain.

DIEP-based breast reconstruction necessitates wide undermining at the abdominal donor-site, creating large wound areas. Flap harvesting is usually conducted using electrosurgical dissection devices. This study sought to compare the clinical outcomes in patients after using the PEAK PlasmaBlade (PPB) versus monopolar electrocautery (MPE). This retrospective cohort study included 128 patients with DIEP-based breast reconstruction. Patient characteristics as well as information on the postoperative course were collected and a comparative evaluation was conducted. The MPE group exhibited significantly (p* = 0.0324) higher abdominal drainage volume (351.11 ± 185.96 ml) compared to the PPB group (279.38 ± 183.38 ml). Subgroup analysis demonstrated that PPB significantly reduced postoperative wound fluid in patients with BMI > 30 kg/m² (p* = 0.0284), without prior neoadjuvant chemotherapy (p** = 0.0041), and among non-smokers (p = 0.0046). Furthermore, postoperative pain was significantly (p**** < 0.0001) lower in the PPB cohort. This study confirms the non-inferiority of the PEAK PlasmaBlade to conventional electrocautery for abdominal flap harvesting. The PPB demonstrated advantages, notably reduced drainage volume and lower postoperative pain levels. Recognizing patient subsets that benefit more from the PPB highlights the importance of personalized device selection based on patient characteristics.

Aiming at the problem of UAV cluster configuration reconstruction, in order to obtain the cluster reconstruction method, the theory and simulation of cluster reconstruction control strategy is studied by simplifying the model，deducing the theoretical formula and analyzing the example. Taking 10 UAVs cluster as an example, the distribution of UAVs in different configurations was analyzed. According to the change of cluster configuration, the principle of formation reconstruction and the execution ability of configuration, the cluster capability was analyzed. The group behavior is modeled by group behavior rules, reconfiguration topology analysis and reconfiguration cost measurement. Based on the cluster parameters and configuration characteristics, simulation experiments were carried out to obtain the change curve of the reconstruction cost and time and the trajectory movement diagram of the UAV in different configurations.