The color changes corresponding to chromophore structures in lignin caused by exposure of Eucalyptus（Eucalyptus grandis and E. urophylla）to heat were investigated. Eucalyptus wood samples were heated in saturated steam atmospheres for 10 h at 110℃, 130℃, and 150℃. The lignin was isolated before and after heat treatment. The physicochemical properties of the lignin and changes in chromophore structures during heat treatment was evaluated through wet chemical analysis, FTIR, UV-Vis, GPC, XPSand 13C-NMR. The color of the wood became darker and redder with the increase in pressure and temperature. Depolymerization and dehydration reactions occurred via demethoxylation with heat treatment in saturated steam at 110℃ or 130℃. Lignin condensed to form insoluble compounds after heat treatment in saturated steam at 150℃. G units increased and S units decreased through demethylation during heat treatment, as revealed by FTIR and 13C-NMR analysis.

The ability to control the temperature distribution T(t,r) and the rate of temperature change Rt,r inside glasses is important for their microstructuring. The lattice temperature is considered at time t, exceeding the electron-phonon thermalization time, and at a distance r from the center of the model spherical heating zone. In order to describe thermal excitations, the heat capacity of glasses must be considered as a function of time due to its long-term relaxation. A method for analytical calculation of T(t,r) and R(t,r) for glasses with dynamic heat capacity cdyn(t) is proposed. It is shown that during laser microstructuring the local cooling rate -R(t,r) significantly depends on the time dispersion of cdyn(t). It has been established that at the periphery of the model heating zone of the laser beam focus, the local cooling rate can reach more than 1011 K/s. Strong cooling rate gradients were found at the periphery of the heating zone, affecting the microstructure of the material. This effect is significantly enhanced by the time dispersion of cdyn(t). The effect associated with this time dispersion is significant even well above the glass transition temperature Tg, since even short relaxation times of the dynamic heat capacity cdyn(t) are significant.

The present paper describes a study case of the failure investigation of Duplex stainless steel (UNS S31803) on the tube and tube sheet section of a shell and tube heat exchanger BEM TEMA type with seawater as the cooling medium. Although UNS S31803 offers high strength, high resistance to chloride-induced SCC, and high resistance to pitting attack in chloride environments, in this study case, the heat exchanger experienced some material degradation; 26 tubes were leaked and plugged on both sides, and scales plugged 76 tubes. The examination in this study case revealed the formation of biofilm inside the tubes, XRD examination revealed that the film contained aragonite (CaCO3), and by using microstructural examination on the inner surface of the tube, the austenite grains were preferentially attacked by crevice corrosion. In this case, the failure was caused by crevice corrosion, and crevice corrosion was enhanced by microbiological-induced corrosion (MIC). Recommendations to avoid similar failures are also suggested in this paper.

The Japanese Association for Acute Medicine Committee recently proposed a novel classification system for the severity of heat-related illnesses. The illnesses are simply classified into three stages based on symptoms and management or treatment. Stages I, II, and III broadly correspond to heat cramp and syncope, heat exhaustion, and heat stroke, respectively. Our objective was to examine whether this novel severity classification is useful in the diagnosis by healthcare professionals of patients with severe heat-related illness and organ failure. A nationwide surveillance study of heat-related illnesses was conducted between June 1 and September 30, 2012, at emergency departments in Japan. Among the 2130 patients who attended 102 emergency departments, the severity of their heat-related illness was recorded for 1799 patients, who were included in this study. In the patients with heat cramp and syncope or heat exhaustion (but not heat stroke), the blood test data (alanine aminotransferase, creatinine, blood urea nitrogen, and platelet counts) for those classified as stage III were significantly higher than those of patients classified as stage I or II. There were no deaths among the patients classified as stage I. This novel classification may avoid underestimating the severity of heat-related illness.

Exposure to extreme heat is a known risk factor that is associated with increased heat-related illness (HRI) outcomes. The relevance of heat wave definitions could change across the health conditions and geographies due to the heterogenous climate profile. This study compared the sensitivity of 28 heat wave definitions associated with HRI emergency department visits over five summer seasons (2011-2016), stratified by two physiographic regions (Coastal and Piedmont) in North Carolina. The HRI rate ratios associated with heat waves were estimated using the generalized linear regression framework assuming a negative binomial distribution. We compared the Akaike Information Criterion (AIC) values across the heat wave definitions to identify an optimal heat wave definition. In the Coastal region, heat wave definition based on daily maximum temperature with a threshold >90^th percentile for two or more consecutive days had the optimal model fit. In the Piedmont region, heat wave definition based on the daily minimum temperature with a threshold value >90^th percentile for two or more consecutive days was optimal. Additionally, we observed that the optimal heat wave definitions from this study captured moderate and frequent heat episodes than the national weather service (NWS) heat products that worked best for extreme heat episodes. This study compared the HRI morbidity risk associated with epidemiologic-based heat wave definitions and with NWS heat products. Our findings could be used for public health education and suggest recalibrating NWS heat products.

Exercise induced bronchoconstriction (EIB) is a common complication of athletes and individuals who exercise regularly. It is estimated that about 90% of patients with underlying asthma experience EIB. Sex differences in the prevalence of asthma have been widely reported, with higher rates in boys vs. girls before puberty, and higher rates in women than men after puberty. Because atopy has been reported to occur at higher rates in athletes than in non-athletes, in this study we investigated sex differences in EIB and atopy in athletes. A systematic literature review identified 60 studies evaluating EIB and/or atopy in post-pubertal adult athletes (n=7501). Collectively, these studies reported: 1) a 23% prevalence of EIB in athletes; 2) a higher prevalence of atopy in male athletes vs. females; 3) a higher prevalence of atopy in athletes with EIB; and 4) a significantly higher rate of atopic EIB in male vs. female athletes. Our analysis indicates that the physiological changes that occur during exercise may differentially affect male and female athletes, and suggest an interaction between male sex, exercise, and atopic status in the course of EIB. Understanding these sex differences is important to provide personalized management plans to athletes with underlying asthma and/or atopy.

This study examines the effects of particle size and heat pipe angle on the thermal effectiveness of a cylindrical screen mesh heat pipe using silver nanoparticles as the test substance. The experiment investigates three different particle sizes (30nm, 50nm, and 80nm) and four different heat pipe angles (0°, 45°, 60°, and 90°) on the heat transmission characteristics of the heat pipe. The results show that the thermal conductivity of the heat pipe increased with an increase in heat pipe angle for all particle sizes, with the highest thermal conductivity attained at a 90° heat pipe angle. Furthermore, the thermal resistance of the heat pipe decreased as the particle size decreased for all heat pipe angles. The thermal conductivity measurements of the particle sizes - 30, 50, and 80 nm - were 250 W/mK, 200 W/mK, and 150 W/mK, respectively. The heat transfer coefficient values for particle sizes 30nm, 50nm, and 80nm were 5500 W/m2K, 4500 W/m2K, and 3500 W/m2K, respectively. The study also found that the heat transfer coefficient increased with increased heat pipe angle for all particle sizes, with the highest heat transfer coefficient obtained at a 90° heat pipe angle.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

Extreme heat is a climate, public health, and environmental justice issue. This case study examined public transit exposure and vulnerability to extreme heat by investigating the microenvironment, land cover characteristics, and social vulnerability of heat-vulnerable bus stops in Knoxville, Tennessee. The community’s temperature and Heat Index information, bus stop point data, land cover characteristics data, and the microenvironment of bus stops (i.e., trees and shelters) were processed and mapped with ArcGIS Pro. The pictures of the microenvironment of the bus stop were collected from Google Maps, and the social vulnerability of the area where the bus stops are located was investigated by analyzing the Center for Disease and Prevention's Social Vulnerability Index. Results found that the most heat-vulnerable bus stops were concentrated in West Knoxville, South, North, Northeast, and Northwest Knoxville. In addition, the most heat-vulnerable bus stops were concentrated in commercial complexes and areas a large number of systematically marginalized populations reside.

Movement disorders can be associated with various drugs and systemic diseases, posing diagnostic challenges for clinicians. This review explores the spectrum of movement disorders associated with pharmacological agents and medical conditions. Drug-induced movement disorders encompass a broad range of conditions resulting from exposure to medications that affect several neurotransmitters. Neuroleptic medications can lead to tardive dyskinesia, characterized by involuntary, repetitive movements. Antipsychotics and antiemetics, including metoclopramide, may induce acute dystonic reactions. Other drugs, such as dopamine receptor-blocking agents, can contribute to drug-induced parkinsonism. Beyond medications, movement disorders can also arise secondary to systemic diseases. Metabolic disorders like Wilson's disease, characterized by copper accumulation, may manifest as chorea or dystonia. Inflammatory conditions such as rheumatoid arthritis and systemic lupus erythematosus can result in secondary movement disorders due to autoimmune-mediated processes affecting the central nervous system. Movement disorders linked to drugs or systemic diseases often necessitate a thorough clinical evaluation, including detailed medication histories and comprehensive systemic assessments. Neuroimaging, laboratory investigations, and, in some cases, cerebrospinal fluid analyses and electrodiagnostic studies help in establishing accurate diagnoses. Management involves addressing the underlying cause, modifying medications, and employing symptomatic treatments.

High in reliability, multi in function, strong in tracking and detecting, active phased array antennas have been widely applied in radar system. Heat dissipation is a major technological barrier preventing the realization of next-generation high-performance phased array antennas. As a result of the advancement of miniaturization and the in-tegration of microelectronics technology, the study and development of embedded di-rect cooling or heat dissipation has significantly enhanced the heat dissipation effect. In this paper, a novel swept-back fishnet embedded microchannel topology (SBFEMCT) is designed, and various microchannel models with different fishnet runner mesh den-sity ratios and different fishnet runner layers are established to characterize the chip Tmax, runner Pmax, and Tmax and analyze the thermal effect of SBFEMCT under these two operating conditions. The Pmax is reduced to 72.37% and 57.12% of the original at mesh density ratios of 0.5, 0.25, and 0.125, respectively. The maximum temperature reduction figures are average with little change in maximum velocity and a small increase in maximum pressure drop for the number of fishing mesh runner layers of 0-4. This paper provides a study of the latest embedded thermal dissipation from the dimension of a single chip to provide a certain degree of new ideas and ref-erences for solving the thermal technology bottleneck of next-generation high-performance phased array antennas.

The condensing heat exchanger is commonly applied in various heat exchange systems. It can efficiently recover moisture and heat from the flue gas that contains water vapor. However, the convective-condensation heat transfer process is so complicated that no mature thermal calculation model is available. This study develops a thermal calculation model for the widely employed tubular condensing heat exchanger in industry. To characterize the degree of the heat and mass transfer, this study introduces two parameters, namely the sensible and latent heat transfer efficiencies of fin. The thermal calculations are conducted for the condensing heat exchangers reported in the literature to verify the proposed model by comparing it with the experimental data. The results show that the absolute error of the calculated sensible and latent heat transfer efficiencies is 0.0365 and 0.0268, respectively. Under the working conditions in this study, a maximum difference of 5.2 K has been acquired between the measured and calculated values of the outlet temperature. The relative error of the condensate water flowrate is mostly within ±5.0% and ±10.0% under the bare-tube and finned-tube conditions, respectively, with a maximum deviation of 0.7 and 1.4 kg h-1. This study provides a general model for designing and optimizing various tubular condensing heat exchangers accurately.

To achieve the required mechanical properties in the heat treatment of steel, it is necessary to have an adequate cooling rate and to achieve the desired final temperature of the product. This should be achieved with one cooling unit for different product sizes. In order to provide high variability of the cooling system, different types of nozzles are used in modern cooling systems. Designers often use simplified, inaccurate correlations to predict the heat transfer coefficient, resulting in oversizing of the designed cooling or failure to provide the required cooling regime. This typically results in longer commissioning times and higher manufacturing costs of the new cooling system. Accurate information about the required cooling regime and the heat transfer coefficient of the designed cooling is critical. This paper presents a design approach based on laboratory measurements. Firstly, the way to find or validate the required cooling regime is presented. The paper then focuses on nozzle selection and presents laboratory measurements that provide accurate heat transfer coefficients as a function of position and surface temperature for different cooling configurations. Numerical simulations using the measured heat transfer coefficients allow the optimum design to be found for different product sizes.

Abstract: High-dose-rate interstitial brachytherapy (HDR-ISBT) has recently come to be considered one of the most effective treatments for oral cancer. On the other hand, it is important to note that radiation therapy has some side effects. Especially, radiation-induced malignancy is probably the most serious complication affecting long-term survivors. We report a case of a radiation-induced undifferentiated spindle cell sarcoma that developed following HDR-ISBT for tongue squamous cell carcinoma (SCC). A 39-year-old woman with right tongue SCC underwent HDR-ISBT (60 Gy, 10 fractions, 8 days) treatment. Five years and one month later, a tumor had developed at the primary site. Surgery was performed for the tumor, which was histopathologically diagnosed as an undifferentiated spindle cell sarcoma. That was distinct from the squamous cell origin of the primary cancer. According to recently established criteria for radiation-induced malignancy, this case was classified as a radiation-induced sarcoma. A search of the literature revealed no previous report of radiation-induced malignancy following HDR-ISBT for tongue cancer.

Chiral interactions play a crucial role in both chemistry and biology. Understanding the behavior of chiral molecules and their interactions with other molecules is essential, and chiral interactions in solutions are particularly important for studying chiral compounds. Chirality influences the physical and chemical properties of molecules, including solubility, reactivity, and biological activity. In this work, we used Isothermal Titration Calorimetry (ITC), a powerful technique for studying molecular interactions, including chiral interactions in solutions. We conducted a series of ITC measurements to investigate the heat of dilution and the heat of racemization of several amino acids (Asn, His, Ser, Ala, Met, and Phe). We also performed ITC measurements under different solute concentrations and temperatures to examine the effects of these parameters on chiral interactions, as well as the heat of dilution and racemization. The results of our measurements indicated that the heat of dilution, specifically the interactions between the solvent (water) and solute (chiral molecules), had a significant impact compared to the chiral interactions in the solution, which were found to be negligible. This suggests that the interactions between chiral molecules and the solvent play a more dominant role in determining the overall behavior and properties of the system. By studying chiral interactions in solutions, we can gain valuable insights into the behavior of chiral compounds, which can have implications in various fields, including drug design, chemical synthesis, and biological processes.

Abstract: The paper compares and analyses the effects of correctly and excessively executed heating cycles on flame straightening, far above the limits recommended by the steel manufacturer. The paperwork emphasizes the microstructural changes induced by overheating in the flame straightening process. Flame straightening is a flame heating process of metal constructions in which very limited areas of the construction are heated to the straightening temperature with the aim of inducing geometrical changes.The flame straightening process is used in most of metallic structure manufacturing companies. In many cases, it is not possible to carry out under economic conditions of metal structures without flame straightening.

Undisturbed ground temperature (UGT), thermal conductivity (TC) and heat capacity (HC) are essential parameters for the design of borehole heat exchanger (BHE) and borehole thermal energy storage systems. However, field methods to assess the thermal state and properties of the sub-surface are costly and time consuming. Moreover, HC is often not evaluated but arbitrarily selected from literature considering the geological materials intercepted by boreholes. Therefore, this work aims at proposing a field heat tracing method to infer the thermal diffusivity (TD) and HC with assumption of natural transient heat conduction in the subsurface. Empirical equations were developed to reproduce a UGT profile measured along a BHE. Experimental coefficients are found with a non-linear least square solver optimization and used to calculate the damping depth and TD. Subsequently, the TD is used to evaluate HC considering TC obtained from a thermal response test (TRT). Results from this proposed heat tracing method were verified and validated against a set of TRT results and oscillatory TRT analysis using a field dual probe concept to infer HC. The example here described highlights the advantages and novelty of this fast and simple field method relying only on a single UGT profile measured before a TRT.

Building roofs are sources of unwanted heat for buildings situated in zones with a warm climate. Thus, reflective coatings have emerged as an alternative to reject a significant fraction of solar energy received by roofs. In this research, the thermal behavior of concrete slab-type roofs with traditional and solar reflective coatings was simulated using a computational tool. Weather data from four cities in Mexico with a warm climate were used as boundary conditions. This tool is an in-house code based on the Finite Volume Method developed by the author to perform building components simulations. The code was validated with experimental data from previous work. A series of comparative simulations were developed, taking a gray roof as a control case. The results showed that for the roof without thermal insulation (single roof), the solar reflective coatings reduced the exterior surface between 11 and 16∘C. Consequently, the single roofs’ daily heat gain was reduced by a factor ranging between 41 and 54%. On the other hand, for the insulated roof, the reflective coatings reduced the exterior surface temperature between 17 and 21∘C. At the same time, the daily heat gain of composite roofs was reduced between 37 and 56%.

Cross flow heat exchangers are commonly used in the thermal industry to transfer heat from hot tubes to cooling fluid. To protect the heat exchanger tubes from corrosion and dust accumulation, microscale coatings are often applied. In this study, we present machine-learning models for predicting heat transfer from hot tubes with different micro-sized coatings to cooling fluid in a turbulent flow using computational fluid dynamics simulations. A dataset of approximately 1000 cases was generated by varying the coating coverage thickness of each tube, the inlet Reynolds number, fluid flow inlet temperature, and wall temperature of tubes. The machine-learning models were generated to predict the overall heat flow rate in the heat exchanger, and it was found that combining the features based on their importance preserved the accuracy of the models while maintaining all the relevant information. The simulation results demonstrate that the proposed method increases the coefficient of determination (R2) for the models. The R2 values for unseen data for Random Forest, K-Nearest Neighbors, and Support Vector Regression were 0.9810, 0.9037, and 0.9754, respectively, indicating the usefulness of the proposed model for predicting heat transfer in various types of heat exchangers.

Motivated by the well-known contradiction of special relativity and the heat equation, a wave equation for temperature scalar field is presented that also resolves the old controversy of (Lorentz) transformation of temperature and entropy. After showing that the current dogma of temperature and entropy being emergent concepts is based on but a logical fallacy, it is proposed that single particles posses entropy. This principle of fundamentality of entropy is then shown to be compatible with the equipartition theorem by yielding corrections in the quantum gravity regime.

A temperate deep lake, Lake Kuttara, Hokkaido, Japan (148 m deep at maximum) was completely frozen every winter in the 20th century. However, unfrozen conditions of the lake over winter occurred four times in the 21st century, which is probably due to global warming. In order to understand how thermal regime of the lake responds to climate change, its heat storage change was calculated by estimating heat budget of the lake and monitoring water temperature at the deepest point for September 2012–June 2016. As a result, temporal change of the heat storage from the heat budget was very consistent with that from the direct temperature measurement (determination coefficient R² = 0.827). The 1978–2017 data at a meteorological station near Kuttara indicated that there are significant (less than 5% level) long-term trends for air temperature (0.024 °C/yr) and wind speed (−0.010 m/s/yr). A sensitivity analysis for the heat storage from the heat budget estimate and an estimate of return periods for mean air temperature in mid-winter allow us to conclude that the lake could be unfrozen once per about two year in a decade.

The air side thermal hydraulic performance of multi-louvered aluminium fin heat exchangers is investigated. A detailed study was performed to analyse the thermal performance of air over a wide range of Reynolds number i.e. from 30 to 250. Air-side heat transfer coefficient and air pressure drop were calculated and validated over the mentioned band of Reynolds numbers. Critical Reynolds number was determined numerically and the variation in flow physics along with the thermal and hydraulic performance of microchannel heat exchanger associated with R_cri has been reported. Moreover, a parametric study of the multi-louvered aluminium fin heat exchangers was also performed for 36 heat exchanger configurations with the louver angles (19-31°), fin pitches (1.0, 1.2, 1.4 mm) and flow depths (16, 20, 24 mm); and the geometric configuration exhibiting the highest thermal performance was reported. The air-side heat transfer coefficient and pressure drop results for different geometrical configurations were presented in terms of Colburn j factor and Fanning friction factor f, as a function of Reynolds number based on louver pitch.

Ocean surface heat fluxes play a significant role in the genesis and evolution of various marine-based atmospheric phenomena, from the synoptic scale down to the microscale. While in-situ measurements from buoys and flux towers will continue to be the standard in regards to surface heat flux estimates, they commonly have significant gaps in temporal and spatial coverage. Previous and current satellite missions have filled these gaps; though they may not observe the fluxes directly, they can measure the variables needed (wind speed, temperature, and humidity) to estimate latent and sensible heat fluxes. However, current remote sensing instruments have their own limitations, such as infrequent coverage, signals attenuated by precipitation, or both. The Cyclone Global Navigation Satellite System (CYGNSS) mission overcomes these limitations over the tropical and subtropical oceans by providing improved coverage in nearly all weather conditions. While CYGNSS (Level 2) primarily estimates surface winds, when coupled with observations or estimates of temperature and humidity from reanalysis data, it can provide estimates of latent and sensible heat fluxes along its orbit. This paper describes the development of the Surface Heat Flux Product for the CYGNSS mission, its current results, and expected improvements and changes in future releases.

Psychosis can be defined as a combination of psychopathological symptoms including delusions and/or hallucinations without insight. Psychotic disorders may configure a primary psychiatric illness or represent the result of a functional/structural brain damage induced by substance use, neurological diseases or other medical conditions. They are multifactorial disorders in which genetic, environmental and gene-environment interaction factors contribute to the expressiveness of the symptoms. Among the environmental factors, psychotropic substances represent the most important removable facilitators of psychosis. In our study, we compared the prevalence of substance induced psychosis between a sample of patients affected by cannabis use disorder and a sample of patients affected by cocaine use disorder analyzing retrospectively the data of outpatients with no personal or family history of psychiatric illnesses.

Drug induced liver injury (DILI) is the most common cause of acute liver failure and 5-10% of patients hospitalized for jaundice are diagnosed with DILI. For a diagnosis of DILI to be made, there should be exclusion of other etiologies of liver injury and the use of a precipitator drug, latency of symptoms, and resolution of liver injury once the offending drug is identified and discontinued. In our case report, we present a patient with idiosyncratic hepatocellular pattern DILI after two doses of ocrelizumab for treatment of multiple sclerosis. Ocrelizumab was given 16 and 27 days prior to the onset of icterus, jaundice, and fatigue, in a patient without the evidence of prior exposure to hepatitis B virus. At presentation labs revealed severe acute hepatocellular liver injury with R factor of 30.42, marked hyperbilirubinemia, and transient hypoalbuminemia. No evidence of latent or active hepatitis B infection was detected. Drug dechallenge led to return of liver chemistries to near-normal levels 31 days after the onset of her symptoms. This case indicates DILI diagnosis associated with the use of ocrelizumab, and warrants careful monitoring of liver functions in patients even in the absence of hepatitis B.

In resettlement planning literature, much has been written on economic, land valuation and compensation, infrastructure and services aspects of the land. Psychological risks and stresses of resettled communities, however, have been under-researched. The current research looks at the psychological risks of resettlers in a Development-Induced Displacement and Resettlement (DIDR) project in Sri Lanka. Focusing on the stages of resettlement planning process discussed by Scudder and Colson four-stage model (1980) and the psychological risks discussed by Cernea’s (1990) impoverishment risks and reconstruction (IRR) model. This study evaluates the significant level of the psychological risks faced by the communities in DIDR projects in Sri Lanka relating to before and after resettlement. Moragahakanda Resettlement Project (MRP) was selected as the case study which is located in Naula DS division of Matale District, Central Province, Sri Lanka. A questionnaire survey, documents and field observations were used to evaluate the current psychological risks. The responses received from multiple choice questions were analyzed by Significant Point (SP) index. The research findings point that there are no conspicuous changes of psychological risks related to before/after resettlement has occurred in re-settlers. The findings highlight that the psychological risk levels in transition stage have remained the same level in the potential development stage. This research provides a systematic guidance enabling the physical planners to prioritize the most significant psychological risks which should be considered in the decision-making process of DIDR projects.

Background: The morbidity of myocardial infarction is keeping raise in this decade. Because of high safety and operability , percutaneous coronary intervention(PCI) has been used to conquer this disease for more than 20 years.An important complication of PCI is contrast induced nephropathy(CIN), which raises our attention. Previously, we started a study to explore the correlation between acute kidney injury and myonecrosis after scheduled percutaneous coronary intervention. Our study showed that the rate of CI-AKI in patients with post-procedural myocardial injury and undergoing elective PCI was higher than that in patients free of injury. Methods: In this study,forty male rats were randomly divided into four groups: control group (n=8), CM group (n=12), AMI group (n=8) and AMI+CM group (n=12), then velocity of renal artery blood flow (VRABF), computer tomography (CT), serum creatinine(Scr), reactive oxidative species (ROS), periodic acid-Schiff (PAS) and TUNEL were used to estimate the injury of kidney. We analyzed 327 non-ST-segment elevation acute coronary syndrome subjects undertaking elective PCI. Serum levels of creatinine (SCr) and the eGFR before coronary angiography, and 24–72 h after contrast administration were recorded to assess the renal function. Results: The data showed that VRABF was lower in AMI+CM group than CM group from 0 minute to 24h and CT number in cortex was higher in AMI+CM group than CM group at 4-hour. As well as the level of Scr in AMI+CM group displayed a significantly increase at 24-hour compared with CM group. The histopathologic scores and percentage of tubular cell apoptosis were higher in AMI+CM group at 24-hour. In 327 patients, we found that CI-AKI occurred more often in subjects with post-procedural myonecrosis (PMN) than in those without PMN (20.8% versus 5.8%, respectively, P=0.001). Conclusion: Compared to the elective patient, the injury of CIN exhibited a higher severity in AMI patient.

The tension cable-supported power transmission structure (TC-PTS) is a new type of power transmission structure suitable for mountainous terrain, which is sensitive to wind load. In this regard, a nonlinear finite element analysis model of wind-induced vibration is proposed for the TC-PTS, and the wind-induced vibration response of the structure is analyzed. Firstly, the tangent stiffness matrix of the three-dimensional truss element for the supporting suspension cable and transmission line, considering the geometric nonlinearity of structures, is derived through the relationship between the element elastic energy and its displacement. Subsequently, the element mass matrix and damping matrix of the supporting suspension cable and transmission line, as well as the element nodal load vector obtained from wind load equivalence are given. Then, based on the nonlinear finite element theory, the nonlinear dynamic equation of wind-induced vibration is established for the TC-PTS and solved by Newmark-β method combined with Newton-Raphson iterative method. Furthermore, the rain-flow counting method and Miner's linear fatigue cumulative damage theory were used for wind induced fatigue damage assessment. Finally, a two-span TC-PTS is selected as an example, and the wind-induced nonlinear vibration and fatigue damage assessment are analyzed through the proposed model. The results show that the proposed model has high computational accuracy and efficiency. With the increase of wind speed and wind direction angle, the maximum lateral displacement and tension of the supporting suspension cable and transmission line increase, and their degree of increase shows a nonlinear trend. In terms of the wind-induced fatigue analysis results of TC-PTS, the fatigue damage at the end of the supporting-conductor suspension cable is greater than the fatigue damage at its midpoint. Compared to the fatigue damage at the midpoint of the conductor, the fatigue damage at the end of the conductor is less affected by wind direction angle, and both are more significantly affected by the wind speed.

This paper presents Mathematical Formulation for Neutrino-Fission of a heavy nuclei in Neutrino-environments. It has been proposed that neutrino fission is a dynamic two-process reaction, where more than one neutrino can be captured by target nucleus. A quantity named Neutrino-Zeta with units of eV^-1 has been defined to represent Neutrino-environments. Neutrino-zeta with assumed excited energy states for heavy nuclei A∼230-270 is estimated to be 0.0212 MeV^-1, with the probability of fission Barrier energy state P(E_x,f)= 0.169064014 with E_x,f =6MeV. P(E_x,f)=0.222664 is highest at zeta=0.1MeV^-1 . It has been shown that probabilities of certain excitation energy states and their corresponding decay reactions at those excitation energies can be equal for two neutrino-zetas. Neutron induced fission for different neutrinos hypothesize that probability of symmetric fission channels is higher at low neutrino-zetas, which can be tested experimentally.

Under the increasingly severe global heat threat, continuous high temperature has far-reaching effects on plant growth and development and become a major constraint to crop production. The development of heat-resistant varieties has become research hotspot in many fields, and it is also necessary to establish effective identification methods. In this study, twenty Brassica rapa varieties were selected to to investigate the physiological and biochemical characteristics under heat stress, explore the relationship between physiological response and the heat resistance mechanism, select some typical heat-resistant and heat-sensitive varieties. The effects of photosynthetic electron transfer and antioxidant pathway on heat resistance of Brassica rapa were identified. These findings will providing an important reference for the physiological regulation and identification method of high-temperature stress in plants.

Increasing wind speed alleviates physiological heat strain, however, health policies have advised against using ventilators or fans under heat wave conditions with air temperatures above the typical skin temperature of 35 °C. Recent research, mostly with sedentary participants, suggests mitigating effects of wind at even higher temperatures depending on the humidity level. Our study aimed at exploring and quantifying, whether such results are transferable to moderate exercise levels, and whether the Universal Thermal Climate Index UTCI reproduces those effects. We measured heart rates, core and skin temperatures and sweat rates in 198 laboratory experiments completed by five young, semi-nude, heat-acclimated, moderately exercising males walking the treadmill with 4 km/h on the level for three hours under widely varying temperature-humidity combinations and two wind conditions. We quantified the cooling effect of increasing wind speed from 0.3 to 2 m/s by fitting generalized additive models predicting the physiological heat stress responses depending on ambient temperature, humidity and wind speed. We then compared the observed wind effects to the assessment performed by UTCI. Increasing wind speed lowered physiological heat strain for air temperatures below 35 °C, but also for higher temperatures with humidity levels above 2 kPa water vapour pressure concerning heart rate and core temperature, and 3 kPa concerning skin temperature and sweat rate, respectively. UTCI assessment of wind effects correlated positively with the observed changes in physiological responses, showing the closest agreement (r=0.9) for skin temperature and sweat rate, where wind is known for elevating the relevant convective and evaporative heat transfer. These results demonstrate the potential of UTCI for adequately assessing sustainable strategies for heat stress mitigation involving fans or ventilators depending on temperature and humidity for moderately exercising individuals.

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

This study mainly experimentally investigates and explores the effects of local low-frequency vibrations on the starting-up and heat transfer characteristics of the pulsating heat pipe. A micro motors with the vibration frequency of 200 Hz were imposed on the external surface of evaporation, condensation and adiabatic section of the pulsating heat pipe, respectively, and the starting-up temperature and the average temperatures along the evaporation section as well as the thermal performances of the vibrating heat pipe were experimentally scrutinized under the local vibrations of different positions. The following important conclusions can be achieved by the experimental study: 1) The effect of vibrations at the evaporation section and at the adiabatic section on the starting-up time of pulsating heat pipe is more significant than that at the condensation section. 2) The vibrations at different positions can reduce the starting-up temperature of the pulsating heat pipe. The effect of the vibrations at the evaporation section is the best as the heating power is lower, and the effect of the vibration at the adiabatic section is the best as the heating power is higher. 3) The vibrations at the evaporation section and at the adiabatic section can reduce the thermal resistance of the pulsating heat pipe. However, the vibrations at the condensation section have little effect on the thermal resistance of the pulsating heat pipe. 4) The vibrations at the evaporation section and at the adiabatic section can effectively reduce the temperature of evaporation section of the pulsating heat pipe, but the vibrations at the condensation section have no effect on the temperature of evaporation section of the pulsating heat pipe.

When considering implementation of shallow geothermal energy as a renewable source for heating and cooling of the building, special care should be taken in hydraulic design of borehole heat exchanger system. Laminar flow can occur in pipes due to usage of glycol mixture at low temperature or inadequate flow rate. This can lead to lower heat extraction and rejection rates of the exchanger because of higher thermal resistances. Furthermore, by increasing flow rate to achieve turbulent flow and satisfactory heat transfer rate can lead to increase the pressure drop of the system and oversizing of circulation pump which leads to impairment of seasonal coefficient of performance at the heat pump. Most frequently used borehole heat exchanger system in Europe is double-loop pipe system with smooth inner wall. Lately, development is focused on implementation of different configuration as well as with ribbed inner wall which ensures turbulent flow in the system, even at lower flow rates. At a location in Zagreb, classical and extended thermal response test was conducted on three different heat exchanger configurations in the same geological environment. With classic TRT test, thermogeological properties of the ground and thermal resistance of the borehole were determined for each smooth or turbulator pipe configuration. Extended Steady-State Thermal Response Step Test (TRST) was implemented, which incorporate series of power steps to determine borehole extraction rate at the define steady-state heat transfer conditions of 0/-3°C. Results show that heat exchangers with ribbed inner pipe wall have advantages over classic double-loop smooth pipe design, in terms of greater steady state heat extraction rate and more favorable hydraulic conditions.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

With heat treatments to control drywood termites (Blattodea: Kalotermitidae), the presence of heat sinks causes heat to be distributed unevenly throughout the treatment areas. Drywood termites may move to galleries in heat sink areas to avoid exposure to lethal temperatures. Our studies were conducted in Crytotermes brevis-infested condominiums in Honolulu, Hawaii to reflect real-world condominium scenarios; either a standard heat treatment performed by a heat remediation company or an improved heat treatment was used. For improved treatments, heated air was directed into the toe-kick voids of C. brevis infested cabinets to reduce heat sink effects and increase the heat penetration into these difficult-to-heat areas. Eight thermistor sensors placed inside toe-kick voids, treatment zone, embedded inside cabinets’ sidewalls, and in a wooden cube recorded target temperatures of above 46 °C or 50 °C for 120 minutes. A pretreatment and follow-up inspections were performed at 6 months posttreatment to monitor termite inactivity using visual observations and by recording the numbers of spiked peaks on a microwave technology termite detection device (Termatrac). In improved treatment condominiums, significantly higher numbers of spiked peaks were recorded at pretreatment as compared to 6 months posttreatment. Efficacious heat treatment protocols using the improved methods are proposed.

Spatially resolved, line-of-sight measurements of aluminum monoxide emission spectra in laser ablation plasma are used with Abel inversion techniques to extract radial plasma temperatures. Contour mapping of the radially deconvolved signal intensity shows a ring of AlO formation near the plasma boundary with the ambient atmosphere. Simulations of the molecular spectra were coupled with the line profile fitting routines. Temperature results are presented with simultaneous inferences from lateral, asymmetric radial, and symmetric radial AlO spectral intensity profiles. This analysis indicates that we measured shockwave phenomena in the radial profiles, including a temperature drop behind the blast wave created during plasma initiation.

Due to the complexity of the microstructure of porous media, it is of great significance to explore the heat transport mechanism in porous media in many engineering applications. In this study, an expression for effective thermal conductivity（ETC） of porous media with randomly distributed damaged tree-like bifurcation networks is derived based on the theory of thermodynamics and fractal features of tree-like bifurcation networks. We investigate the effect of heat conduction and heat convection in porous media with randomly distributed damaged tree-like bifurcation networks on the ETC of the porous media. It is found that our fractal model is in good consistency with the existing available experimental data. In addition, the influence of the micro-structural parameters of the model on heat transfer in the porous media have been analyzed in detail. The research results can provide significant theoretical guidance for the development and design of heat transfer systems.

Testicular heat stress is a well described phenomenon that occurs in mammals that possess a scrotum. Different models to induce testicular hyperthermia, such as surgical cryptorchidism, hot water bath, scrotal insulation or increased environmental temperature have all shown that spermatocytes and spermatids are unambiguously affected by high temperature, resulting in poor sperm production weeks later. Furthermore, a body of evidence suggest the involvement of oxidative stress is either a major or contributory pathway, which gives rise to the potential to overcome this condition. Whilst experimental models conclusively show the deleterious effect of testicular heat on sperm quality, the physiological relevance of the work is still debated. Herein we summarise a cohort of studies that report the effect of “season” on sperm quality. The data show season can affect sperm production, motility and morphology depending on where the work was performed. In countries where temperatures drop below zero, there is evidence showing summer conditions tend to improve semen quality. However, in sub-tropical countries, some studies show a decrease in summer, whilst others show no change. Herein we offer a reasonable explanation for this apparent controversy and present a range of antioxidant supplements that may offer some protection against testicular hyperthermia.

Heat using behavior has a large impact on in heating energy in heat metering system, and therefore a better understanding can assist in behavior guidance to reduce energy. To understand the current situation of indoor thermal environment and heat using behavior for heat metering households in northern China, including adjusting heating end valves and operating windows, 30 households were measured and surveyed. The factors influencing heat using behavior, including outdoor and indoor environmental parameters and time of the day, were analyzed. The results are :1) Thermal neutral temperature for heat metering households is relatively high, up to 24.5℃; 2) The heat using behavior of households is lack of rationality: low proportion of active households; high indoor temperature setting; more frequency of window opening. Improving indoor comfort is the main reason for households to adjust the heating end valve, and only 7.15% of households have considered the economic benefits brought by adjusting the valve. " Thermostat control valve does not work" is the main reason for households without adjustment; 3) Time of the day and indoor temperature affect active households’ willingness to adjusting heating end valve. Time of the day, indoor temperature and outdoor temperature have impacts on opening window during heating period.

A solid structure, such as a road, building wall or envelop, used as a solar collector is considered an effective and new way to use renewable energy. This paper focused on the temperature characteristics of four structures exposed to sunshine: asphalt, red brick, composite cement and concrete road slab. Furthermore, the collected heat based on a hydraulic system was investigated experimentally. For the four structure slabs, their temperature differences are due to solar radiation absorption varied greatly by the material’s heat absorptance and color. Through the test, asphalt slab attained the highest temperature and had the weakest reflection among the structures. Compared with the others, the temperature of the asphalt slab was greater by 8.1%, 14.9% and 16.4% than the brick, composite cement and concrete, respectively. The reflection intensity growth ratio was defined and indicates the growth potential for absorbing radiation in the solid slab surface. From the experiments, it was concluded that a suitable selection of road materials can greatly improve the thermal absorption, conduction and penetration into the solid slab. The collected heat capability was approximately 250 W/m2 to 350 W/m2 in the natural summer condition. A black coating or a surface modification can collect more heat, reaching greater than 250 W/m2. The solar collecting heat efficiency with a surface configuration of the road slab can reach above 30% in the summer time.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

This paper studies the evaporative heat transfer characteristics of R744 at low temperatures in a horizontal smooth tube as a cascade refrigeration system (CRS) among hybrid cascade refrigeration systems (HCRSs). There is a lack of research on the low-temperature evaporative heat transfer characteristics of R744 under the operating conditions of evaporators used in actual CRSs used in supermarkets. Therefore, this study aims to provide basic data on the evaporative heat transfer characteristics of R744 in the evaporators of refrigerators used in supermarkets. The tube used in the evaporation experiment conducted herein was a smooth horizontal copper tube with an inner diameter and length of 11.46 mm and 8000 mm, respectively. The experimental pa-rameters were as follows: heat fluxes of 12–21.5 kW/m2, mass fluxes of 75–225 kg/(m2·s), and saturation temperatures of −50–−30 °C. The main results are summarized as follows. (1) When designing the R744 evaporator, the mass and heat fluxes must be maximized within the operating conditions, and the saturation temperature must be designed to be as low as possible. (2) The evaporative heat transfer coefficient of R744 can be predicted well by using the correlation formula of Chen at the evaporation temperature of −40 °C in the CRS.

Biomimetic design has recently received widespread attention. Inspired by the Terebridae structure, this paper provides a structural form for suppressing vortex-induced vibration (VIV) response. Four different structural forms are shown, including the traditional smooth cylinder (P0), the Terebridae-inspired cylinder with a helical angle of 30° (P30), the Terebridae-inspired cylinder with a helical angle of 60° (P60), and the Terebridae-inspired cylinder with a helical angle of 90° (P90). And computational fluid dynamics (CFD) method is adopted to solve the flow pass the Terebridae-inspired structures, and the vibration equation is solved using the Newmark-β method. The results show that the VIV responses are effectively controlled in the lock-in region for P30, P60, and P90, and P60 shows the best VIV suppression performance. The transverse amplitude and the downstream amplitude can be reduced by 82.67% and 91.43% respectively for P60 compared with that for P0, and the peak of the mean-drag coefficient is suppressed by 53.33%. The Q-criterion vortices of P30, P60, and P90 are destroyed, with irregular vortices shedding. It is also found that the boundary layer separation is located on the Terebridae-inspired ribs. The twisted ribs cause the separation point to constantly change along the spanwise direction, resulting in the development of the boundary layer separation being completely destroyed. The strength of the wake flow is significantly weakened for the Terebridae-inspired cylinder. In the lock-in region, the motion trajectory presents a typical 8-shaped for P0, while the motion trajectory of the Terebridae-inspired cylinder tends to be a flat 1-shaped.

Trichoderma spp. are widely used in plant disease control as biocontrol agents. Inducing plant disease resistance is an important biocontrol mechanism of Trichoderma. It is of great significance to explore the factors involved in the surface recognition and interaction of Trichoderma with plants. Hydrophobin is a small molecular protein rich in cysteine in higher filamentous fungi and has been found to participate in the morphogenesis and interaction of fungi with other organisms. In this study, the type II hydrophobic protein-coding gene Thfb6 from T. harzianum TH33 was cloned and heterologously expressed in Escherichia coli BL21 (DE3). The purified recombinant protein Thfb6 induced a hypersensitive response in tobacco leaves, a burst of reactive oxygen species, and an accumulation of callose, phenolic substances, and lignin in tobacco, indicating that Thfb6 can induce an early defense reaction in tobacco. Thfb6 also enhanced the systemic resistance of tobacco against tobacco mosaic virus. The rate of lesion number reduction by treatment with Thfb6 could be up to 36.02%. Thfb6 increased the activity of tobacco defense-related enzymes, including phenylalanine ammonia-lyase (PAL), polyphenol oxidase, and peroxidase, which were all more than three times the control after 3–5 days post treatment of Thfb6. The transcription of resistance-related genes, including the PAL gene, non-expresser of pathogenesis-related gene1 (NPR1), and basic pathogenesis-related gene 1 (PR1-b), were upregulated after Thfb6 treatment. The relative expression levels of the PAL and NPR1 genes were highest on the third and fourth days after Thfb6 treatment, at 5.5 times and 8.3 times that of the control, respectively. The relative expression level of PR1 on the sixth day after Thfb6 treatment was 5.3 times that of the control. These results indicate that the improvement of defense-related enzyme activity and the induced expression of disease-resistance-related genes were the main mechanisms by which Thfb6 induced systemic resistance in tobacco.

Fusarium wilt diseases severely influence the growth and productivity of numerous crop plants. The consortium of antagonistic rhizospheric Bacillus strains and quercetin were evaluated imperatively as a possible remedy to effectively manage the Fusarium wilt disease of tomato plants. The selection of Bacillus strains was made based on in-vitro antagonistic bioassays against Fusarium oxysporum f.sp. lycoprsici (FOL). Whereas, quercetin was selected after screening a library of phytochemicals during in-silico molecular docking analysis using tomato LysM receptor Kinases “SILKY12” based on its dual role in symbiosis and plant defense responses. After the selection of test materials, pot trials were conducted where tomato plants were provided consortium of Bacillus strains as soil drenching and quercetin as a foliar spray in different concentrations. The combined application of consortium () and quercetin (1.0 mM) reduced the Fusarium wilt disease index up to 69% also resulting in increased plant growth attributes. Likewise, the imperative application of the Bacillus consortium and quercetin (1.0 mM) significantly increased total phenolic contents and activities of the enzymes of the phenylpropanoid pathway. Non-targeted metabolomics analysis was performed to investigate the perturbation in metabolites. FOL pathogen negatively affected a range of metabolites including carbohydrates, amino acids, phenylpropanoids, and organic acids. Thereinto, combined treatment of Bacillus consortium and quercetin (1.0 mM) ameliorated the production of different metabolites in tomato plants. These findings prove the imperative use of Bacillus consortium and quercetin as an effective and sustainable remedy to manage Fusarium wilt disease of tomato plants and to promote the growth of tomato plants under pathogen stress conditions.

Land use/land cover (LULC) changes have a substantial influence on ecosystem services. The objective of this study is to estimate LULC dynamics induced ecosystem service values (ESV) changes in Western Ethiopia. Data were acquired from Landsat images of the area for four periods (1990-2020), and 221 sample households. The areas of LULC classes and the improved ESV coefficients of Costanza et al (1997) were used estimate ESV changes in 1990-2020. Forest provides diverse provisions, regulatory, supportive and cultural services. Analysis of the Landsat images showed that forest, farmland, settlement, water body and bare-land were the major LULC classes in the study area. While forest ESV had accounted 46.1% (US$ 4.95 million) of the ESV of Wayu-Tuka district in 1990, farmland ESV constituted the largest share (63.3%, US$ 5.21 million) of the ESV of the area after 30 years (2020). The ESV of forest and bare-land showed decreasing trends in three decades (1990-2020) but the farmland service value revealed an increasing trend in the same periods. Forest ecosystem exhibited the largest service value loss (US$ 3.91 million) in 1990-2020; whereas, the service value gain of farmland was only US$ 2.2 million although farmland was responsible for the conversion of the largest area size (9,766.5 ha) from other land covers in 30 years. LULC change induced net ESV loss of the district in three decades (1990-2020) was 23.4% (US$ 2.51 million). Land conversion due to expansion of farmland (by 9,766.5 ha) and settlement (by 4,061.3 ha) was the main cause for the LULC dynamics and the significant ESV loss in 1990-2020. Thus, the government and local people should cooperate so as to curb the steady degradation of forest and its ecosystem services in Wayu-Tuka district, Western Ethiopia.

A switchable and tunable terahertz (THz) metamaterial based on photosensitive silicon and Vanadium dioxide (VO2) was proposed. By using finite-difference time-domain (FDTD) method, the transmission and reflective properties of the metamaterial were investigated theoretically. The results imply that, the metamaterial can realize a dual electromagnetically induced transparency (EIT) or two narrow-band absorption depending on the temperature of the VO2. Additionally, the magnitude of the EIT and two narrow-band absorption can be tuned by varying the conductivity of photosensitive silicon (PSi) via pumping light. Correspondingly, the slow light effect accompanying the EIT can also be adjusted.

The plant immunity system is more and more revisited and new elements and roles are attributed to participate in the response to biotic stress. New terminology is also applied trying to identify different players in the whole scenario of immunity: Phytocytokines are one of those elements that are gaining more attention due the characteristics of processing and perception, and showing they are part of a big family of compounds that can amplify the immune response. This review aims to highlight the last findings about the role of phytocytokines in the whole immune response on biotic stress, including basal and adaptive immunity, and to expose the complexity in their action in plant perception and signaling events.

This study presents the developments regarding the time-domain-induced polarisation method, as a supporting tool for resistivity soundings during investigations of coastal detrital aquifers that are salinised by marine intrusion. The interpretation of resistivity measurements in such aquifers, which have variable hydrochemistry and lithology, involves uncertainties owing to the presence of low-resistivity lithologies, such as clays. To reduce these uncertainties, the use of other geophysical parameters is necessary; hence, this study focuses on induced polarisation, since it can be measured simultaneously with resistivity. In detail, we propose the determination of induced polarisation using 1D techniques, while developing a different algorithm for processing the induced polarisation data. The aim is to extend the results of this phenomenon, using instead of chargeability, the concepts of polarisability and decay time, which are extracted from the decay curve, given that they represent more intrinsic properties of the various analysed subsurface media. We present results obtained by applying this methodology to a Quaternary aquifer of the Costa del Sol in the SE Iberian Peninsula (in the province of Almería) during two different campaigns, one before and one after winter (i.e., in October and February, respectively). The results reveal the position of the saline front during each campaign, while reflecting the seasonal movement of the marine intrusion.

This paper develops the study of the effect of powerful ultrasound on the laser breakdown of liquids and a comparative study of the possibilities of acoustic and optical diagnostics of breakdown. The method of laser-induced breakdown spectroscopy (LIBS) for elemental analysis of liquids, along with high efficiency, continues to be less sensitive compared to traditional chemical methods. The paper develops a method of using additional ultrasound irradiation of the laser breakdown area in order to increase the efficiency of LIBS. Using the developed technique, spectral lines of chemical elements such as potassium, manganese, sodium, calcium, etc. were obtained for the first time depending on the frequency and power of ultrasound. It is shown that a sharp increase in the intensity of spectral lines of elements in water during laser breakdown is observed in the field of high-power ultrasound. It indicates an increase in the sensitivity of the combined method of ultrasonic LIBS. Along with the optical spectrum, the spectral and energy characteristics of acoustic emission were studied. An automated complex for hydrophysical and spectral studies is described, which was tested in the Sea of Japan during the voyage No. 81 of the research vessel RV "Professor Gagarinsky" in August 2022.

We have developed an unsteady and non-linear wind synopsis simulator called RIAM-COMPACT (Research Institute for Applied Mechanics, Kyushu University, COMputational Prediction of Airflow over Complex Terrain) in order to simulate the airflow on a microscale, i.e., a few tens of km or less. In RIAM-COMPACT, the large-eddy simulation (LES) has been adopted for turbulence modeling. LES is a technique in which the structures of relatively large eddies are directly simulated and smaller eddies are modeled using a sub-grid scale model. In the present study, we have conducted the numerical wind diagnoses for Taikoyama Wind Farm nacelle separation accident in Japan. The simulation results suggest that all six wind turbines at the Taikoyama Wind Farm are subject to significant influence from separated flow (terrain-induced turbulence) which is generated due to the topographic irregularities in the vicinity of the wind turbines. A proposal has been also made on reconstruction of the wind farm.

In this paper, comprehensive analysis of combined effect of major influencing parameters on heat transfer in the single U-tube BHE (sBHE) and double U-tube BHE (dBHE) with two independent circuits was performed by using validated numerical heat transfer model. Geometrical parameters, such as shank spacing (with maximum, average and minimum values) and borehole diameter (large, medium and small borehole sizes) and borehole depth (shallow, average and deep borehole depths) as well as thermal conductivity of soil and grout which ranges from minimum to high value were considered. The combined impact of these parameters was included under four major cases: 1) combined effect of borehole depth, borehole size and shank spacing; 2) combined effect of borehole depth, and soil and grout thermal conductivity; 3) combined effect of soil and grout thermal conductivity and borehole size; and 4) combined effect of soil thermal conductivity, borehole size and shank spacing. Each of these major cases has nine different design options of both sBHE and dBHE. Series of results of heat transfer per unit borehole depth were generated for all the considered various cases. With the given parameters, the BHE case that provides highest heat transfer among the various cases of sBHE and dBHE were obtained.

Enhancing the Efficiency of Natural Gas Liquid (NGL) Extraction and Fractionation Trains: An Integrated Approach of Simulation Analysis, Advanced Modifications, and Technological Advancements. Through comprehensive research, innovative solutions such as the heat pump aided distillation (HPAD) system and self-heat recuperation technology (SHRT) have been developed to significantly reduce the energy consumption associated with conventional distillation systems. To identify a practical system for NGL fractionation trains, this study extensively examined and compared various HPAD and SHRT options to retrofit a single column. The objective was to find the most suitable and efficient solution for the fractionation process of natural gas liquids (NGLs). The retrofit options analyzed in this study encompassed a range of techniques, including vapor compression (VC), mechanical vapor re-compression (MVR), thermal vapor re-compression (TVR), bottom flashing (BF), side heat exchanger (SHE), intermediate heating and cooling (IHC), self-heat recuperative (SHR), and modified self-heat recuperative (MSHR) distillation. These methods were carefully examined to determine their suitability and effectiveness in improving the performance of NGL fractionation trains.In this study, a depropanizer column, typically employed in conventional NGL plants, was selected as a case study. The simulation software Aspen HYSYS V7.3 was employed to model and analyze eight retrofit designs based on predefined criteria. The simulation data was carefully evaluated to identify the most efficient design for minimizing energy consumption. Among the retrofit options, the mechanical vapor re-compression (MVR) technique demonstrated the most significant energy cost reduction, with a remarkable 68.11 percent improvement compared to the base case conventional column. These findings highlight the potential of MVR as an effective solution for lowering energy costs in NGL fractionation trains.Following the MVR retrofit option, the study found that vapor compression (VC) achieved a considerable energy cost reduction of 66.65 percent, closely followed by modified self-heat recuperative (MSHR) at 64.02 percent, bottom flashing (BF) at 62.88 percent, self-heat recuperative (SHR) at 55.85 percent, side heat exchanger (SHE) at 54.23 percent, intermediate heating and cooling (IHC) at 39.54 percent, and thermal vapor re-compression (TVR) also at 39.54 percent. These findings highlight the significant potential for energy savings offered by these retrofit options, with VC being the most popular choice, closely followed by MSHR, BF, SHR, SHE, IHC, and TVR.

Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

Economic expedience of waste heat recovery systems (WHRS), especially for low temperature difference applications, is often questionable due to high capital investments and long pay-back periods. By its simple design isobaric expansion (IE) machines could provide a viable pathway to utilize otherwise unprofitable waste heat streams for power generation and particularly for pumping liquids and compression of gases. Different engine configurations are presented and discussed. A new method of modelling and calculation of the IE process and efficiency is used on IE cycles with various pure and mixtures as a working fluid. Some interesting cases are presented. It is shown in this paper, that the simplest non-regenerative IE engines are efficient at low temperature differences between a heat source and heat sink. Efficiency of non-regenerative IE process with pure working fluid can be very high approaching Carnot efficiency at low pressure and heat source/heat sink temperature differences. Regeneration permits to increase efficiency of the IE-cycle to some extent. Application of mixed working fluids in combination with regeneration permits to significantly increase the range of high efficiencies to much larger temperature and pressure differences.

The research examines the relationship between self-rated health situation and personal percep-tion of heat waves, and how social linkage of communities would be a moderator variable in residents’ perception of heat waves in Taiwan. This study uses the questionnaire conducted by Sinica “Responsive Capacity under Heat Wave: The Perspectives of the Locals”(2019), using OLS method for estimating the unknown parameters in multiple regression model. The author finds that the correlation of self-rated health situation and perception toward heat is significantly posi-tive. Also, social linkage in communities affects strongly as a moderator variable: While the sat-isfaction to with their community could reduce negative reaction to heat, contacts with neighbors could increase possibility people feel uncomfortable in high-temperature situation. This study ex-hibits the effects of social environment on community, and expects further related researches or practices to strengthen capability to resist heat wavesƒ for Taiwanese residents.

This paper shares some new information on the ambient temperature profile and the heat stress occurrences directly underneath ground-mounted Solar Photovoltaic (PV) Arrays (monocrystalline-based) focusing on different temperature levels. A common ground for this work lies on the fact that 10C increase of PV cell temperature results in reduction of 0.5% energy conversion efficiency thus any means of natural cooling mechanism would gain much benefit especially to the Solar Farm operators. Transpiration process plays an important role in the cooling of green plants where in average it could dissipate around 32.9% of the total solar energy absorbed by the leaf making it a good natural cooling mechanism. This condition is relatively applied for herbs specifically for this project, Orthosiphon Stamineus or generally known as Java Tea are used as the high value crops. The thermal process via convective heat and mass exchange of leaves with the environment is relevant for a better understanding of plant physiological processes in response to environmental conversion factors for a wide range of applications. An important fact for plant heat stress with respect to the Ambient temperature is that the range lies between 10 C to 15 C above the surrounding value. This heat stress condition is relatively important and should be modelled in crops-energy integration. Agrivoltaic concept is a system that combines commercial agriculture and photovoltaic electricity generation in the same space. The concept is in line with the Kyoto Protocol and the United Nation Sustainable Development Goals (UN-SDG) which highlights the clean energy and sustainable urban living. The integration of agrivoltaic systems would optimize the yield, improving clean system efficiency and solving the issue of land resource sustainability. The PV bottom surface temperature are the main source of dissipated heat as shown in the thermal images recorded at 5 minutes interval at 3 sampling time. Statistical analysis shows that the Thermal correlations for transpiration process and heat stress occurrences between PV bottom surface and plant height will be an important finding for large scale plant cultivation in agrivoltaic farms.

The aim of this paper is to expose the main involved physical phenomena underlying the alteration of convective heat transfer in a heat exchanger subjected to imposed vibrations. This technique seems to have interesting features and industrial applications, such as efficiency increase, heat transfer rate control and cleanliness action. However, a clear description and comprehension of how vibrations may alter the convective heat transfer coefficient in a heat exchanger is no still reached due to the complexity of the involved physical mechanisms. For this reason, after a presentation and a schematisation of the analyzed thermodynamic system, the fundamental alterations of the thermo-fluid dynamics fields are described. Then, the main involved physical phenomena are exposed for the three cases of gaseous, monophasic liquid and boiling liquid mediums. Finally, on the basis of the characteristics of these described phenomena, some considerations and indications of general validity are presented.

Flying-fox populations are increasingly threatened by heat events, starvation events and other stressors due to habitat clearing and human/flying-fox conflict.These factors are unlikely to resolve, meaning that a well-coordinated and timely approach to flying-fox disasters is imperative for the mitigation of further flying-fox population impacts.

Developing high performance HVAC system using natural refrigerants including carbon dioxide (CO₂) has been important in respect of environmental preservation and associated technologies. Thus studies to optimize the HVAC (heating ventilation air conditioner) system using natural refrigerants through clarifying the cycle performance characteristics are necessary. The CO₂ heat pump system using air and water sources was consisted to examine its performance characteristics, and by varying conditions of several factors that affect or characterize the system performance like the amount of refrigerant charge, EEV (electronic expansion valve) opening, and internal heat exchanger under cooling mode. The performance characteristics of CO₂ heat pump system were tested by using an air enthalpy calorimeter. In the case of the CO₂ heat pump system without internal heat exchanger, the opening of #3 EEV and #4 EEV was 60% and refrigerant charge amount was 5,600g. However, in the case of that with internal heat exchanger, the best performance was obtained when the opening of #2 EEV is 20%. From the present studies, it was observed that the performance variation and operational characteristics of the CO₂ heat pump system were affected by design factors like refrigerant charge amount, EEV opening, and internal heat exchanger and thereby, the configuration on an optimal operation conditions of the system was enabled.

In January and February 2001, El Salvador was hit by two strong earthquakes that triggered thousands of landslides, causing 1,259 fatalities and extensive damage. The analysis of aerial and SPOT-4 satellite images taken a few days after the events allowed us to map 6,491 coesismic landslides, which occurred in 14 study areas extending for about 400 km2. Four different Multivariate Adaptive Regression Splines (MARS) models were produced by using different covariate sets and landslide inventories, the latter containing the slope failures triggered by an extreme rainfall event of November 2009 and those induced by the earthquakes of 2001. Moreover, two validation scenarios were employed, including the 25% and 95% of the mapped landslides, respectively. The results of our experiment revealed that: (i) MARS algorithm provides reliable predictions of coesismic landslides; (ii) models calibrated with rainfall-induced landslides predict with acceptable accuracy landslides caused by deep earthquakes and distributed over vast areas; (iii) the best accuracy is achieved by models trained with both preparatory and trigger variables; (iv) a small portion of the landslides produced by an earthquake can be used to calibrate MARS predictive models that help to identify slopes where yet unreported landslides may have occurred.

An increasing amount of electric energy is consumed by computers as they progress in function and capabilities. All of it is dissipated in heat during the computing and communicating operations and we reached the point that further developments are hindered by the unbearable amount of heat produced. In this paper we briefly review the fundamental limits in energy dissipation, as imposed by the laws of physics, with specific reference to computing and memory storage activities.

Transposable elements (TEs) are highly abundant in plant genomes. Environmental stress is one of the critical stimuli that activate TEs. We analyzed a heat-activated retrotransposon named ONSEN in cruciferous vegetables. The multiple copies of ONSEN-like elements (OLEs) were found in all the cruciferous vegetables that were analyzed. The copy number of OLE was abundant in Brassica oleracea, which includes cabbage, cauliflower, broccoli, Brussels sprout, and kale. Phylogenic analysis demonstrated that some OLEs transposed after the allopolyploidization of parental Brassica species. Furthermore, we found that the increasing number of OLEs in B. oleracea appeared to be induced transpositional silencing by epigenetic regulation, including DNA methylation. The results of this study would be relevant to the understanding of evolutionary adaptations to thermal environmental stress in different species.

The electrification of process industries is one of the main challenges when building a low-carbon society since they consume huge amounts of fossil fuel generating different emissions. Heat pumps are one of the instruments to perform industrial sector of carbon-neutral market players. This paper proposes an approach to improve the economic feasibility of heat pumps within the process plants. Initial energy targeting with Grand Composite Curves was used and supplemented with the detailed design of the evaporator and compressor for different condensation and evaporation pressures. The trade-off between the capital cost of the heat pump and the electricity cost was investigated and optimal configurations were selected. The case study investigates the gas fractioning unit of a polymer plant where three heat pumps were integrated into distillation columns. The results demonstrated that the heat recovery is 174 MW and requires an additional 37.9 MW of electricity to reduce hot utility by 212 MW. The selection of evaporation and condensation pressure of heat pumps allows saving of 21.5 M€/y for 7 years of plant operation.

The effects of anisotropic properties (wettability and roughness) on microgroove surfaces in pool boiling heat transfer using Novec-7100 as a working fluid were experimentally investigated. The idea of introducing the concept of anisotropic wettability in boiling experiments draws inspiration from biphilic surfaces. The investigation is also motivated by two-phase immersion cooling, which involves phase-change heat transfer by using dielectric liquid as a working fluid. Very few studies have focused on the effects of surfaces with anisotropic properties on boiling performance. Thus, this study aims to examine the pool boiling heat transfer performance on surfaces with microgroove-induced anisotropic properties under the saturation condition. A femtosecond laser–texturing method was employed to create microgroove surfaces with different groove spacing. The results indicated that anisotropic properties affected the heat transfer coefficient and critical heat flux. Relative to the plain surface, microgroove surfaces enhanced the heat transfer performance due to the increased number of bubble nucleation sites and higher bubble detachment frequency. An analysis of bubble dynamics under different surface conditions was conducted with the assistance of high-speed images. The microgroove surface with groove spacing of 100 μm maximally increased the BHTC by 37% compared to the plain surface. Finally, the CHF results derived from experiments were compared with related empirical correlations. Good agreement was achieved between the results and the prediction correlation.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

Drug-induced liver disease represents one of the main problems in the therapeutic field. As with most pathologies, also in this case various risk factors can be recognised, such as age, sex, but also the gut microbiota. Therefore all drugs on the market can, in fact, cause hepatotoxicity of varying degrees. Drugs used in the treatment of IBD can also cause these adverse effects and even lead to DILI. In this review, the various classes of drugs used in the treatment of IBD were taken into consideration and the various adverse effects on the liver were illustrated. In particular, a major role has emerged regarding hepatotoxicity of immunosuppressants. Biological drugs, however, seem to be responsible for these complications to a much lesser extent.

Within the spectra of lanthanide atoms quite often overlapping spectral lines (blends) are observed. On the example of complicated blend situations within Pr I and La I it is shown that in such cases a combination of optogalvanic and laser-induced fluorescence detection is necessary to find all transitions contributing to the observed spectral signature.

Peptidylarginine deiminases (PADs) have an important role in the pathogenesis of generating citrullinated proteins which is one type of protein posttranslation modifications (PTMs). Additionally, peptidylarginine deiminases 4 (PAD4) is a component of neutrophil extracellular traps (NET) that leads to autoimmune disease during NETosis. Our aim was to check the PAD4 enzyme expression at level of gene and protein expression in streptozotocin (STZ) induced diabetic rat pancreas and checking the link between PAD4 and inflammatory cytokines. Wistar rats were divided into two groups: control group and diabetic STZ group. STZ was administered by intraperitoneally (60 mg/kg/ body weight). Rats were caged for six weeks and then terminated. Pancreatic tissue was harvested for measurement of PAD4 protein expression, PAD4 mRNA, citrulli-nated histone-3 protein (CITH3), cytokines and Ca2+ content. All measurements in diabetic rats were significantly in-creased compared to non-diabetic rats (p

Tongue mobility is an obstructive sleep apnoea (OSA) marker and myofunctional therapy (MFT) target. For this reason, all patients with sleep-disordered breathing should require a combined functional assessment from an ear, nose, and throat (ENT) specialist and a phonoaudiologist to confirm or rule out the presence of tongue-tie. To our knowledge, this is the first case of a 13-year-old girl diagnosed with severe OSA and a significant decrease of 94% in her apnoea index (AI), requiring frenotomy with immediate postoperative change in the tongue position. A drug-induced sleep en-doscopy (DISE) was performed before and immediately post-frenotomy, and the anatomical changes provoked by this surgery during sleep were confirmed for the first time.

Induced pluripotent stem cells (iPSC) are derived from reprogrammed adult somatic cells. These adult cells are manipulated in vitro to express genes and factors essential for acquiring and maintaining embryonic stem cell (ESC) properties. This technology is widely applied in many fields, and there has been much attention to developing iPSC-based disease models to validate drug discovery platforms and study pathophysiological molecular processes underlying disease onset. Especially in neurological diseases, there is a great need for iPSC-based technological research, as these cells can be obtained from each patient and carry the individual’s bulk of genetic mutations and properties. Moreover, iPSC can differentiate into multiple cell types. These are essential characteristics since the study of neurological diseases is affected by limited access to injured sites, in vitro models composed of various cell types, the complexity of reproducing the brain’s anatomy, ethical issues, and the fact that post-mortem cell culture is challenging. Neurodegenerative diseases enormously impact global health due to their high incidence, symptoms severity, and usually lack of effective therapies. Recently, analyses using disease-specific iPSC-based models confirmed their efficacy for testing multiple drugs. This review summarizes the advances in iPSC technology used in disease modeling and drug testing with a primary focus on neurodegenerative diseases, including Parkinson’s and Alzheimer’s diseases.

Idiosyncratic drug induced liver injury (DILI) is an unpredictable reaction of exposed individual on a certain drug, and the drug-induced autoimmune hepatitis (DIAIH) presents a DILI phenotype that mimics idiopathic autoimmune hepatitis (AIH) when considering the clinical, biochemical, serological and histological parameters. We present a case of a 48-year-old male that was hospitalized due to severe hepatocellular liver injury two months after the self-treatment with the muscle-building dietary supplement based on arginine-alpha-ketoglutarate, L-citrulline, L tyrosine, creatine malate and beet extract. His immunology panel was positive with increased IgG levels, and the radiologic methods showed no signs of chronic liver disease. He underwent corticosteroid treatment with adequate response. After the therapy withdrawal, a clinical relapse occurred. Seven months after the initial presentation liver MR suggested the initial cirrhotic changes of the right liver lobe. Liver biopsy revealed abundant lymphoplasmacytic infiltrate with piecemeal necrosis and grade 2 fibrosis. He responded well on the corticosteroid treatment again, and was further treated with low dose prednisone without additional relapses. Several years later, further management confirmed presence of liver cirrhosis with no histological or biochemical signs of the disease activity. DIAIH is a DILI phenotype difficult to distinguish from idiopathic AIH despite a wide armamentarium of diagnostic methods. Regular patient monitoring and clinical open-mindedness with the adjustment of therapeutic approaches according to the disease course are more important than strict labelling of the disease.

Background: Pteropodine (PT) is a component of some plants with potentially useful pharmaco-logical activities for humans. This compound has biomedical properties related to the modulation of the immune system, nervous system, and inflammatory processes. This study addresses the an-ti-inflammatory and antioxidant capacity of pteropodin in a murine model of arthritis and induced edema of the mouse ear. Methods: To evaluate the anti-inflammatory activity, we used the reversed passive Arthus reaction (RPAR), which includes the rat paw edema test, the rat pleurisy test, and a mouse ear edema model. The antioxidant effect was evaluated by determining the myeloperoxidase enzyme activity. Results: PT showed an anti-inflammatory effect in the different specific and non-specific tests. We found a 52 to 74% of inhibitory effect of PT in the rat paw edema test, 52% of reduction of the pleural exudate volume, and low neutrophil count (28%), when compared to the control group. We also found a 81% of inflammatory inhibition of the ear edema, and a significant myeloperoxidase enzyme inhibition by the three doses of PT. Conclusions: PT exerted a potent an-ti-inflammatory effect in the acute inflammation model in rodents.

The soil-borne pathogens, particularly Fusarium oxysporum f. sp. niveum (FON) and southern root-knot nematode (RKN, Meloidogyne incognita) are the major threat to watermelon production in the south-eastern United States. The role of soil micronutrients on induced resistance (IR) to plant diseases is well-documented in soil-based mediums. However, soil-based mediums limit the determination of the role(s) of individual micronutrients in IR. In this manuscript, we utilized hydroponics to assess the effect of controlled application of micronutrient, including iron (Fe), manganese (Mn), and zinc (Zn) on the expression of some IR genes (PR1, PR5, and NPR1 from salicylic acid (SA) pathway, and VSP, PDF, and LOX genes from jasmonic acid (JA) pathway) in watermelon seedlings upon inoculation with either FON or RKN or both. Plants were treated with higher (3X) or lower (0.5X) concentrations of micronutrients in Steiner solution (X= standard dose of micronutrient) for 7 days in a hydroponics system under greenhouse conditions. A subset of micronutrient-treated plants was inoculated (on the 8th day of micronutrient application) with FON and RKN (single and mixed). The expression of the IR genes in treated and control samples were evaluated using qRT-PCR. Although, significant phenotypic differences were not observed with respect to the severity of wilt symptoms or RKN galling with any of the micro-nutrient treatments within the 30 day-experimental-period, differences in the induction of IR genes were observed. However, the level of gene expression varied with sampling period, type and concentration of micro-nutrients ap-plied, and pathogen-inoculation. In the absence of pathogens, no significant changes were observed in the expression level of IR genes on 7th day of micronutrient treatment. However, pathogen inoculation affected the expression levels of the IR genes at 3-day post-inoculation. In FON inoculated plants, PDF was upregulated in high Fe treatment, whereas in RKN inoculated plants, low Mn treatment resulted in up-regulation of VSP. In the case of mixed inoculation with FON and RKN, the plants with low Zn treatment resulted in the upregulation of PR1. These observations suggest that the type and concentration of micronutrients in watermelon may potentially induce systemic resistance against FON and RKN through SA and JA pathways.

MiRNAs are 20-22 nucleotide long single-stranded non-coding RNA sequences, which can regulate post transcriptional activity of mRNA by binding with it at 3’UTR region (untranslated region). Thus deregulation of miRNA expression is responsible for dysregulating mRNA function which contributes in developing various diseases as well as cancerous phenotypes. Alteration of single nucleotide in miRNA sequence is one of the reasons behind deregulation of miRNA expression. The most frequent carcinoma in current day is breast cancer which causes a high mortality among women around the world as well as India. Despite of the advancement of diagnostic tools, strategies and treatment, the cases of breast cancer is increasing every year. There are plenty of biomarkers like ER, PR, Her2, Ki-67, etc available which are frequently used in diagnosis and treatment of breast cancer. After the discovery of MiRNA in 1993 in Caenorhabiditis elegans, it is attracting all the limelight in diagnosis and treatment of different carcinomas as well as breast cancer. In this review we will discuss on involvement of different types of MiRNAs and miR SNPs in breast cancer occurrence and susceptibility in a detailed manner.

In the present study, field observation wind data from the time of the wind turbine blade damage accident on Shiratakiyama Wind Farm were analyzed in detail. In parallel, high-resolution LES turbulence simulations were performed in order to examine the model’s ability to numerically reproduce terrain-induced turbulence. The comparison of the observed and simulated time series (1 second average values) from a 10 minute period from the time of the accident led to the conclusion that the settings of the horizontal grid resolution and time increment are important to numerically reproduce the terrain-induced turbulence that caused the wind turbine blade damage accident on Shiratakiyama Wind Farm. A spectral analysis of the same set of observed and simulated data revealed that the simulated data reproduced the energy cascade of the actual terrain-induced turbulence well.

At the Atsumi Wind Farm in Aichi Prefecture, Japan, damage to wind turbines occurred frequently due to terrain-induced turbulence. In the present study, numerical analyses of terrain-induced turbulence were conducted by reproducing the topography in the vicinity of the wind turbine sites in high resolution and using RIAM-COMPACT natural terrain version, which is based on large eddy simulation (LES). The results of the diagnoses indicated that, in the case of south-easterly wind, terrain-induced turbulence is generated at a small terrain feature located upstream of Wind Turbine (WT) #2, which serves as the origin of the turbulence. At the Atsumi Wind Farm, a combination of the series of wind diagnoses and on-site operation experience led to a decision to adopt an "automatic shutdown program" for WTs #1 and #2. Here, "automatic shutdown program" refers to the automatic suspension of wind turbine operation upon the wind speed and direction meeting the conditions associated with significant effects of terrain-induced turbulence at a wind turbine site. The adoption of the "automatic shutdown program" has successfully resulted in a large reduction in the number of occurrences of wind turbine damage, thus, creating major positive economic effects. 1) a reduction in the repair costs by 9.322 million yen per year per wind turbine, 2) an increase in the availability factor by 8.05%, and 3) an increase in the capacity factor by 1.7%.

We use earthquake ground motion modelling via Ground Motion Prediction Equations (GMPEs) and numerical simulation of seismic waves to consider the effects of site amplification and basin resonance in Jakarta, the capital city of Indonesia. While spectral accelerations at short periods are sensitive to near-surface conditions (i.e., Vs30), our results suggest that, for basins as deep as Jakarta’s, available GMPEs cannot be relied upon to accurately estimate the effect of basin depth on ground motions at long periods (>1 s). Amplitudes at such long periods are influenced by entrapment of seismic waves in the basin, resulting in longer duration of strong ground motion, and interference between incoming and reflected waves as well as focusing at basin edges may amplify seismic waves. In order to simulate such phenomena in detail, a basin model derived from a previous study is used as a computational domain for deterministic earthquake scenario modeling in a 2-dimensional cross-section. A M_w 9.0 megathrust, a M_w 6.5 crustal thrust and a M_w 7.0 instraslab earthquake are chosen as scenario events that pose credible threats to Jakarta, and the interactions with the basin of seismic waves generated by these events were simulated. The highest PGV amplifications are recorded at sites near the middle of the basin and near its southern edge, with maximum amplifications of PGV in the horizontal component of 200% for the crustal, 600% for the megathrust and 335% for the deep intraslab earthquake scenario, respectively. We find that the levels of ground motion response spectral acceleration fall below those of the 2012 Indonesian building Codes's design response spectrum for short periods (< 1 s), but closely approach or may even exceed these levels for longer periods.

A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

With the development of energy internet, integrated energy system can effectively reduce carbon emissions and improve the utilization of renewable energy. In this paper, a low-carbon optimal scheduling model of integrated energy system considering heat loss of heat network pipeline is proposed. Based on the study of concentrating solar power (CSP) plant and heat storage tank (HS), an optimal scheduling model is established, which takes system operation cost, environmental pollution and penalty cost of abandoning wind and solar energy as objectives. Through the analysis of example results, it is proved that the model proposed in this paper can achieve the goal of reliable, low-carbon and economic operation of the system. At the same time, it shows that CSP unit can reduce the operation cost of system and increase energy coupling and utilization.

The first detection of gypsum (CaSO4.2H2O) by the Mars Science Laboratory (MSL) rover Curiosity in the Gale Crater, Mars created a profound impact on planetary science and exploration. The unique capability of plasma spectroscopy involving in situ elemental analysis in extraterrestrial environments, suggesting the presence of water in the red planet based on phase characterization and providing a clue to Martian paleoclimate. The key to gypsum as an ideal paleoclimate proxy lies in its textural variants, and in this study terrestrial gypsum samples from varied locations and textural types have been analyzed by Laser Induced Breakdown Spectroscopy (LIBS) technique. Petrographic, sub-microscopic and powder X-ray diffraction characterizations confirm the presence of gypsum (hydrated calcium sulphate; CaSO4.2H2O), bassanite (semi-hydrated calcium sulphate; CaSO4.1/2H2O) and anhydrite (anhydrous calcium sulphate; CaSO4) along with accessory phases (quartz and jarosite). The principal component analysis of LIBS spectra from texturally varied gypsums can be differentiated from one another because of the chemical variability in their elemental concentrations. The concentration of gypsum is determined from the partial least-square regressions model. Rapid characterization of gypsum samples with LIBS is expected to work well in extraterrestrial environments.

The object of this work is to determine the correlation on the Nusselt number on the individual rows of a four-row tubular finned heat exchanger with continuous fins with a staggered tube arrangement using CFD modelling. Correlations for calculating Darcy-Weisbach friction factors on individual tube rows were also determined. Relationships for the Nusselt number and friction factor derived for the entire exchanger based on CFD modelling were compared with those available in the literature determined using experimental data. The maximum relative differences between the Nusselt number for a four-row exchanger determined experimentally and by CFD modelling are in the range from 22% for a Reynolds number based on a tube's outside diameter of 1,000 to 30% for a Reynolds number of 13,000. The maximum relative differences between the friction factor for a four-row exchanger determined experimentally and by CFD modelling are in the range of 50% for a Reynolds number based on a tube outer diameter of 1,000 to 10% for a Reynolds number of 13,000. The CFD modeling performed shows that in the range of Reynolds numbers based on hydraulic diameters from 150 to 1,400, the Nusselt number for the first row in a four-row finned heat exchanger is about 22% to 15% higher than the average Nusselt number for the entire exchanger. In the range of Reynolds number changes based on hydraulic diameter from 2,800 to 6,000, the Nusselt numbers on the first and second rows of tubes are close to each other. Correlations on Nusselt numbers and friction factors derived for individual tube rows can be used in the design of plate-fin and tube heat exchangers used in equipment such as air-source heat pumps, automotive radiators, air-conditioning systems and in air hot-liquid coolers. In particular, the correlations can be used to select the optimum number of tube rows in the exchanger.

This paper investigates a numerical code coupling technique to tackle multi-physics and multi-scale simulations using state-of-the-art software packages that typically address some specific modeling domain. The coupling considers the in-house FEM code, FEMuS, and the FVM code OpenFOAM, by exploiting the MED library from the SALOME platform. The present approach is tested on a buoyancy-driven fluid flow within a square cavity, where the buoyancy force constitutes the coupling term. In uncoupled scenarios, momentum and temperature equations are solved both in FEM and FVM codes without data exchange. In the coupled setting, only the OpenFOAM velocity and the FEMuS temperature fields are solved separately and shared at each time step (or vice versa). The MED library handles the coupling with the addition of suitable ad-hoc data structures that perform the field transfer between codes. Different Rayleigh numbers are investigated, comparing the outcomes of coupled and uncoupled cases with reference literature results. Additionally, a boundary data transfer application is presented to extend the capabilities of the coupling algorithm to coupled applications with separate domains. In this problem, the two domains share interfaces and boundary values on specific fields as fluxes are exchanged between the two numerical codes.

Heat stress results in significant economic losses to the poultry industry. Genetics plays an important role in chickens adapting to the warming environment. Physiological parameters, including hematochemical parameters, change in response to heat stress in chickens. To explore the genetics of heat stress resilience in chickens, a genome-wide association study (GWAS) was conducted using Hy-Line Brown (HLB) layer chicks treated with either high ambient temperature or combined high temperature and Newcastle disease virus (NDV) infection. Hematochemical parameters were measured during three treatment phases: acute heat stress, chronic heat stress, and chronic heat stress combined with NDV infection. Significant changes in blood parameters were recorded for 11 parameters across the three treatments. The GWAS revealed 39 significant SNPs (P < 0.05) for 7 parameters, located on Gallus gallus chromosomes (GGA) 1, 3, 4, 6, 11, and 12. The significant genomic regions were further investigated to examine if the genes within the regions were associated with the corresponding traits under heat stress. A candidate gene list including genes in the identified genomic regions that were also differentially expressed in chicken tissues under heat stress was generated. Understanding the correlation between genetic variants and resilience to heat stress is an important step in improving heat tolerance in poultry.

Hay and straw are commonly used materials in agriculture. They are organic materials and therefore flammable. This article examines the behaviour of hay and straw when exposed to radiant heat. The objective of this study is to experimentally determine the ignition temperature of hay and straw under the influence of radiant heat. The research investigates the effects of sample type (hay and straw) and sample quantity on the thermal degradation process, temperature increase within the samples, and ignition temperature of the samples as a function of time. The ignition temperature of hay was determined to be higher (407°C) compared to straw (380°C). The results did not demonstrate a significant correlation between sample type and the thermal degradation process or the ignition temperature of hay and straw.

Anode bonding is a widely used method for fabricating devices with suspended structures, and this approach is often combined with deep reactive ion etching (DRIE) for releasing the device. However, the DRIE process with a glass substrate can potentially cause two critical issues: heat accumulation on the suspended surface and charging effects resulting from the reflection of charged particles from the glass substrate. In particular, for torsional bars with narrow width, the heat accumulated on the suspended surface may not dissipate efficiently, leading to photoresist burning and subsequently resulting in the fracture of the torsional bars. Moreover, once etching is finished through the silicon diaphragm, the glass surface becomes charged, and incoming ions are reflected towards the back of the silicon, resulting in the etching of the back surface. To address these issues, we proposed a method of growing silicon oxide on the back of the device layer. By designing, simulating, and fabricating electrostatic torsional micromirrors with common cavity silicon-on-glass (SOG) structures, we successfully validated the feasibility of this approach. This approach ensures effective heat dissipation on the suspended surface, even when the structure is over-etched for an extended period, and enables the complete etching of torsional bars without adverse effects due to the overheating problem. Additionally, the oxide layer can block ions from reaching the glass surface, thus avoiding the charging effect commonly observed in SOG structures during DRIE.

Space shuttle has been a hall mark of American space program since its inception. Despite its temporary shutdown few years ago, with the recent interest in space exploration which includes revitalizing human outpost in microgravity and transportation required to build it, realize other experiments (e.g. in space telescopes, in space manufacturing) and interplanetary voyages, it has regained attention. Its superior design, manufacturing, materials, performance, durability, and efficiency place it among the best, in fact, the only effort by mankind to build a reusable craft horizontally, launch vertically like a rocket and fly back like a plane. Various requirements emerge during its design (thermal, fluid, acoustics, vibration and structural) and design of its main engine (Aerojet Rocketdyne RS 25) which requires considerable attention, heat transfer being most important. This facilitated and necessitated use of various types of heat exchangers such as single coil, heat pipe, built in internal heat exchanger (IHEX), external heat exchanger (EHEX), condensing heat exchanger (CHEX), Interface heat exchangers (InHEX), regenerative heat exchanger (RHEX) and compact heat exchangers (CoHEX), change, manipulate and optimize their configurations in piping and instrumentation diagrams (PIDs). In this short narrative, an effort has been made to summarize them, and their developments over time with a focus on the application, design, manufacturing, materials, and performance (in service and final operation).

The purpose of this study is to check out the involvement of entropy in Mpemba effect. Provided that preheating of the water the cooling duration is reduced, we theoretically show that water gains more entropy when warmed and re-cooled to the original temperature.

Fermenter is a vessel that maintains optimum environment for the development of significant microorganism used in large scale fermentation process and the commercial production of products like Alcoholic beverages, Enzymes, Antibiotics, Organic acids etc. The fermenter aims to produce biological product like vaccines and hormones, it is necessary to monitor and control the different parameters like external and internal mass transfer, heat transfer, fluid velocity, shear stress, agitation speed, aeration rate, cooling rate or heating intensity, and the feeding rate, nutrients, base or acid valve. Fermentation in the fermenter are accomplished in several configuration and these simple configurations are batch, fed-batch and continuous fermentation process. Fermentation process is carried out in small or large size fermenter depending on product quantity. The selection of the suitable process depends on the fermentation kinetics, type of microorganism used and process economic aspects. Improved modelling tools, reactor operation and reactor design in bioreactor is because of mass transfer behavior and it is important for reaction rate maximizing, throughput rates optimization and cost minimizing. The fermenter design, fermentation process, types of the fermenter that are used in industries and heat and mass transfer in fermenter is discussed.

In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen, depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation, and the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased, while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

In the present paper, laminar forced convection nanofluid flows in a uniformly heated horizontal tube were revisited by direct numerical simulations. Single and two-phase models were employed with constant and temperature-dependent properties. Comparisons with experimental data showed that the mixture model performs better than the single-phase model in the all cases studied. Temperature-dependent fluid properties also resulted in a better prediction of the thermal field. A particular attention was paid to the grid arrangement. The two-phase model was used then confidently to investigate the influence of the nanoparticle size on the heat and fluid flow with a particular emphasis on the sedimentation process. Four nanoparticle diameters were considered: 10, 42, 100 and 200 nm for both copper-water and alumina/water nanofluids. For the largest diameter dnp = 200 nm, the Cu nanoparticles were more sedimented by around 80 %, while the Al₂O₃ nanoparticles sedimented only by 2.5 %. Besides, it was found that increasing the Reynolds number improved the heat transfer rate, while it decreased the friction factor allowing the nanoparticles to stay more dispersed in the base fluid. The effect of nanoparticle type on the heat transfer coefficient was also investigated for six different water-based nanofluids. Results showed that the Cu-water nanofluid achieved the highest heat transfer coefficient, followed by C, Al₂O₃, CuO, TiO₂, and SiO₂, respectively. All results were presented and discussed for four different values of the concentration in nanoparticles, namely φ = 0, 0.6, 1 and 1.6%. Empirical correlations for the friction coefficient and the average Nusselt number were also provided summarizing all the presented results.

Introduction the outbreak of the Israel-Gaza conflict, initiated by a major attack on the civilian population in Israel provided a tragic opportunity to study the community wide association between severe emotional stressors related to acts of war and the incidence and clinical characteristics of Takotsubo cardiomyopathy (TCM) in this scenario. Methods Eight consecutive cases of TCM diagnosed during the first 50 days of the Israel-Gaza conflict were retrospectively collected from two southern medical centers who provided care to most of the war victims throughout the period of monitoring. The medical records were thoroughly reviewed and analyzed. Results During the monitoring period, the incidence of TCM increased substantially compared to the control period. Eight patients were included in the analysis. All patients were female and 100% of patients presented within the first 3 weeks of conflict whereas after this initial phase, despite the continuing war, the incidence of TCM reverted to pre-conflict levels. Two patients (25%) were under 50 years of age. All patients had hazardous clinical characteristics including severe left ventricular (LV) dysfunction (≤35%) and prolonged QTc interval (>500 ms). Five patients (62.5%) experienced complications. Nevertheless, no in-hospital mortality was reported. Conclusions Repeated exposure to severe emotional stress, on both personal and national level, due to mass crisis such as war is associated with an increased incidence of TCM potentially with high-risk phenotype in comparison to TCM following other, less potent, psychological insults.

Familial Alzheimer’s disease (FAD) can be caused by mutations in PSEN1 that encodes presenilin-1, a component of the gamma-secretase complex that cleaves amyloid precursor protein. Alterations in calcium (Ca2+) homeostasis and glutamate signaling are implicated in the pathogenesis of FAD, however it has been difficult to assess in humans whether or not these phenotypes are the result of amyloid or tau pathology. This study aimed to assess early calcium and glutamate phenotypes of FAD by measuring the Ca2+ response of induced pluripotent stem cell (iPSC)-derived neurons bearing PSEN1 mutations to glutamate and the ionotropic glutamate receptor agonists NMDA, AMPA and kainate compared to isogenic control and healthy lines. The data shows that in early neurons, even in the absence of amyloid and tau phenotypes, FAD neurons exhibit increased Ca2+ responses to glutamate and AMPA, but not NMDA or kainate. Together this suggests that PSEN1 mutations alter Ca2+ and glutamate signaling as an early phenotype of FAD.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

Hiccups can significantly reduce the quality of life of patients and can occur as a drug side effect. Previous report using the Drug Adverse Event Database revealed sex-specific differences in the incidence of drug-induced hiccups. However, the pathogenesis of drug-induced hiccups remains unknown, and there is limited evidence on its treatment or prevention. This study examined molecular initiating events (MIEs), which are the starting point of adverse events, to investigate the drug-induced pathways of hiccups. We extracted drugs suspected to cause hiccups using FDA Adverse Event Reporting System, a large database on adverse drug reactions. Information on drugs suspected to be associated with hiccups were extracted from the overall population and sex-specific subgroups divided. In each data table, the predicted activity values of nuclear receptors (NRs) and stress response pathways (SPs) for each drug were calculated using the toxicity predictor, a machine-learning model. Univariate analysis extracted NRs and SPs associated with hiccups, and a multivariate analysis was performed to evaluate independent factors. Transforming growth factor-beta and antioxidant response element were considered an independent factor for hiccups in the male and female subgroups, respectively. This report first examined one of the mechanisms of drug-induced hiccups and identified MIEs associated with drug-induced hiccups.

Contrast-Induced Acute Kidney Injury (CI-AKI) remains a frequent iatrogenic condition since radiological procedures using intra-vascular iodinated contrast media (CM) are being widely administered for diagnostic and therapeutic purposes. Despite the improvement of the medical healthcare system worldwide, CI-AKI is still associated with direct short-term and indirect long-term outcomes including increased morbidity and mortality, specially, in patients under-lying pre-existing renal function impairment, cardiovascular disease or diabetes that could rap-idly progress into Chronic Kidney Disease. Although the RIFLE (Risk, Injury, Failure, Loss, End-Stage Kidney Disease), AKIN (Acute Kidney Injury Network) and KDIGO (Kidney Disease Improving Global Outcomes) clinical criteria and recommendation guidelines are based on tra-ditional “gold standard” biomarkers known as serum creatinine, glomerular filtration rate and urinary output, new reliable serum and urinary biomarkers are still needed for an effective uni-fied diagnostic strategy for AKI. Starting from previous and recent publications on the benefits and limitations of validated biomarkers responding to kidney injury, glomerular filtration and inflammation among others, this review unravels the role of new emerging biomarkers used alone or in combination, as reliable tools for early diagnosis and prognosis of CI-AKI, taking into account patients and procedures-risk factors towards a new clinical perspective.