The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

This study investigates the potential of a hybrid nanofluid composed of MoS2 and ZnO nanoparticles dispersed in engine oil, aiming to enhance the properties of lubricant's chemical reaction with the Soret effect on stretching sheet under the influence of applied magnetic field. With the growing demand for efficient lubrication systems in various industrial applications, including automotive engines, the development of novel nanofluid-based lubricants presents a promising avenue for improving engine performance and longevity. However, the synergistic effects of hybrid nanoparticles in engine oil remain relatively unexplored. This research addresses this gap by examining the thermal conductivity, viscosity, and wear resistance of the hybrid nanofluid, shedding light on its potential as an advanced lubrication solution. By analyzing the dispersion stability and interaction mechanisms between nanoparticles and base oil, valuable insights are gained into the fundamental aspects governing the entertainment of hybrid nano lubricants. Overall, the objectives of studying hybrid nano lubricant MoS2+ZnO with engine oil aim to advance the development of more efficient and durable lubrication solutions for automotive engines, contributing to improved reliability, fuel efficiency, and environmental sustainability. Governing non-linear partial differential equations are simplified as ordinary differential equations by utilizing similarity variables. MATLAB Bvp4c technique is used to solve the obtained linear ODE equations. The outputs are presented through graphs and tables for various state variables. The comparative survey in all the graphs is presented for the nanofluid (MoS2/Engine oil) with the hybrid nanofluid (MoS2+ZnO/Engine oil). These graphs show the effect of various parameters M, Q, β, Pr, Ec, Sc, Sr, Kp, Kr and (hybrid nano lubricant parameter). The velocity profile diminished against the values of M, Kp, and β. Temperature profile rising with Ec and Q. reciprocally goes down to Pr. The concentration profile incremented with the value of Sr and decremented with the value of Sc, and Kr. With the increasing value of both f′ (η) and θ(η) increases. But in θ(η) hybrid nanofluid slows down with the higher value of .

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

Enhancing the Efficiency of Natural Gas Liquid (NGL) Extraction and Fractionation Trains: An Integrated Approach of Simulation Analysis, Advanced Modifications, and Technological Advancements. Through comprehensive research, innovative solutions such as the heat pump aided distillation (HPAD) system and self-heat recuperation technology (SHRT) have been developed to significantly reduce the energy consumption associated with conventional distillation systems. To identify a practical system for NGL fractionation trains, this study extensively examined and compared various HPAD and SHRT options to retrofit a single column. The objective was to find the most suitable and efficient solution for the fractionation process of natural gas liquids (NGLs). The retrofit options analyzed in this study encompassed a range of techniques, including vapor compression (VC), mechanical vapor re-compression (MVR), thermal vapor re-compression (TVR), bottom flashing (BF), side heat exchanger (SHE), intermediate heating and cooling (IHC), self-heat recuperative (SHR), and modified self-heat recuperative (MSHR) distillation. These methods were carefully examined to determine their suitability and effectiveness in improving the performance of NGL fractionation trains.In this study, a depropanizer column, typically employed in conventional NGL plants, was selected as a case study. The simulation software Aspen HYSYS V7.3 was employed to model and analyze eight retrofit designs based on predefined criteria. The simulation data was carefully evaluated to identify the most efficient design for minimizing energy consumption. Among the retrofit options, the mechanical vapor re-compression (MVR) technique demonstrated the most significant energy cost reduction, with a remarkable 68.11 percent improvement compared to the base case conventional column. These findings highlight the potential of MVR as an effective solution for lowering energy costs in NGL fractionation trains.Following the MVR retrofit option, the study found that vapor compression (VC) achieved a considerable energy cost reduction of 66.65 percent, closely followed by modified self-heat recuperative (MSHR) at 64.02 percent, bottom flashing (BF) at 62.88 percent, self-heat recuperative (SHR) at 55.85 percent, side heat exchanger (SHE) at 54.23 percent, intermediate heating and cooling (IHC) at 39.54 percent, and thermal vapor re-compression (TVR) also at 39.54 percent. These findings highlight the significant potential for energy savings offered by these retrofit options, with VC being the most popular choice, closely followed by MSHR, BF, SHR, SHE, IHC, and TVR.

This research concerns in to understand the link between urban heat and cool island, the Local Climatic Zones (LCZ) and atmospheric systems during the winter season in the city of Balneário Camboriú, Southern Brazil. To collect meteorological data on urban environmental, 11 permanent points in the Balneário Camboriú metropolitan region were installed. To understand the atmos-pheric systems operating in the region, a synoptic analysis of the dates was performed, and then, the LCZs map created for the city in World Urban Database and Acess Portal Tools was used to cor-relate the magnitudes of the heat and cool islands found in Balneário Camboriú in the winter period. The results indicate that the increasing verticalization with the construction of skyscrapers in Balneário Camboriú has a significant influence on local conditions for the occurrence of heat and cold islands. The findings indicate that LCZs with sparsely distributed buildings (LCZs 6, 8 and 9) and LCZs with dense vegetation (LCZ A) have lower intensity magnitudes of heat and cool con-ditions. The biggest magnitudes of heat and cool islands were reported in LCZs 1 and 3 during the timeframe. The synoptic analysis supports earlier researches that points to atmospheric stability (Anticyclonic domain) as a favorable atmospheric setting for the emergence of urban hear and coolness islands.

The Urban heat island (UHI) effect has evolved into one of the key environmental problems affecting urban ecological environment and sustainable development. Based on 52 Urban Thermal Heat spots (UTHSs) with significant differences between land use structure and UGI spatial layout within the influence range of UHI in Shanghai, Landsat-8/9 satellite images were used to construct a high-dimensional data set reflecting the impact of built environment components on urban thermal environment. Descriptive statistical analysis was used to analyze the spatial difference qualitatively. Using stepwise regression model and partial least square regression (PLSR) model, the complex response relationship between UGI pattern differentiation and urban thermal environment in three spatial stratification ranges of UTHSs was quantitatively analyzed. Overall, the statistical explanatory power of the partial least square regression PLSR model is due to the stepwise regression model. The PLSR model points out that moderately increasing the average building height, CA, PLAND, LSI and LPI play a positive role in inhibiting/slowing down the growth of LST (land surface temperature), and the cooling effect of index weights decreases in order. However, the interaction effects of CA×Cohesion×AI×LPI and PLAND×CA×Cohesion×AI×LPI exert relatively small weight on the cooling effect, and according to the results, suggestions such as UGI structure and urban construction layout optimization can effectively alleviate the urban heat island effect are proposed.

This study examines the optimization of ground source heat pump (GSHP) systems and energy piles for sustainable urban development, with a focus on Southeast Asia. GSHPs, which utilize geothermal energy for indoor HVAC needs, offer a sustainable alternative to traditional systems by utilizing consistent subsurface temperatures for heating and cooling. The study highlights the importance of understanding thermal movement within the soil, especially in soft marine clays prevalent in Southeast Asia, to improve GSHP system efficiency. Using a one-dimensional finite-difference model, the study examines the effects of soil thermal conductivity and density on system performance. The results show that GSHP systems, especially when integrated with energy piles, significantly reduce electricity consumption and greenhouse gas emissions, underscoring their potential to mitigate the urban heat island effect in densely populated areas. Despite challenges posed by the region's hot and humid climate, which could affect long-term effectiveness, the study highlights the need for further study, including field experiments and advanced modeling techniques, to optimize GSHP configurations and fully exploit geothermal energy in urban environments. The study's insights into soil thermal dynamics and system design optimization contribute to the advancement of sustainable urban infrastructure development.

We have now identified two thermodynamically distinct types (A and B) of energetic processes naturally occurring on Earth. Type A energy processes such as the classical heat engines, apparently well follow the second law of thermodynamics; Type B energy processes, such as the newly discovered thermotrophic function that isothermally utilizes environmental heat energy to do useful work in driving ATP synthesis, which follows the first law of thermodynamics (conservation of mass and energy) but does not have to be constrained by the second law, owing to their special asymmetric functions. Several Type-B energy processes such as asymmetric-function-gated isothermal electricity and epicatalysis have been created through human efforts. The innovative efforts on Type-B processes to enable isothermally utilizing endless environmental heat energy could help to liberate all peoples from their dependence on fossil fuel energy, thus helping to reduce greenhouse gas CO2 emissions and control climate change towards a sustainable future for the humanity on Earth.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

This paper introduces a new adaptation of the enthalpic lattice Boltzmann method (LBM) tailored to simulate the intricate dynamics of conjugate heat transfer in non-homogeneous media, showcasing considerable potential for enhancing heat exchanger designs. This approach expands upon the conventional enthalpic LBM framework by seamlessly incorporating tailored source terms, enabling precise representation of local and transient variations in the medium’s thermophysical properties. The resulting LBM model comprehensively captures the energy conservation equation, with exceptions made only for flow compressibility and viscous dissipation, thereby significantly augmenting its versatility in analyzing heat exchanger configurations. Verification tests, comprising assessments of both transient and steady-state solutions, unequivocally validate the accuracy of the proposed model, further bolstering its reliability for analyzing heat exchange processes within intricate heat exchanger geometries. To demonstrate its efficacy, simulations of conjugate heat transfer processes involving fluid natural convection within structured cavities were performed, imposing both Dirichlet and Neumann boundary conditions to emulate scenarios encountered in practical heat exchanger operations. The findings yield compelling insights, particularly in the transient regime, revealing the beneficial impact of structured cavities on enhancing heat transfer processes. These insights inform potential design optimizations for heat exchangers. The results emphasize the potential of the modified enthalpic LBM approach to elucidate complex heat transfer phenomena in non-homogeneous media and structured geometries, offering valuable implications for heat exchanger engineering and optimization.

Pulverized coal pyrolysis based on solid heat carrier has a huge advantage in high tar yield. In this study, pyrolysis experiments of pulverized coal were conducted in a lab-scale fluidized bed reactor at 650 ℃, utilizing char as the solid heat carrier. The influence of mass ratio of char to coal (RATIO) was investigated. Results show that the incorporation of solid heat carrier of char significantly enhanced the initial reaction in coal pyrolysis, resulting in increasing yields of tar and gas but reducing one of char. The yield of tar maximally reached 148.80-262.22% of the Gray-King analysis value at the RATIO of 14.52 g/g. As the RATIO increased, the tar contained more light component content, indicating that incorporating solid heat carriers improved the tar quality. These findings offer significant insights for the design of fluidized bed pyrolysis unit utilizing char as solid heat carrier.

The sound and heat insulation are among the most important concerns in modern life and nonwoven composite structures are highly effective in noise reduction and heat insulation. In this study, three layered nonwoven composite structures composed of recycled polyester (r-Pet) based thermo bonded nonwoven outer layer and meltblown nonwovens from PP and PBT as inner layers were formed to provide heat and sound insulation. Fiber fineness and cross section of thermo bonded outer layer, fiber type (PP/PBT), areal weight (100/200g/m2) and process conditions (calendared/non-calendared) of meltblown inner layer have changed systematically and the influence of these parameters on thickness, bulk density, air permeability, sound absorption coefficient and thermal resistance of composite structures were analyzed statistically. Also; the results were compared with composite structures including electrospun nano fiber web inner layer and with structures without inner layer. It was determined that sound absorption coefficients ranging between 0.77-0.98 for moderate sound frequencies and 0.99-1 for higher sound frequencies were acquired with developed nonwoven composite structures. Besides, higher sound absorption coefficients were obtained as 0.71 and 0.74 for low sound frequencies such as 800 and 1000Hz, respectively. As a result of this study it can be concluded that developed nonwoven composite structures that provides better sound absorption coefficients and similar thermal conductivity values compared to previous studies and materials in the market can be used as insulation material in required areas.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

1,3,5-Tris-(α-naphthyl)benzene is an organic non-electrolyte with notable stability of an amorphous phase. Its glassy and supercooled liquid states were previously studied by spectroscopic and calorimetric methods. However, the thermodynamic parameters of phase transitions available from the literature are inconsistent. In this work, the heat capacities of crystalline and liquid phases, the temperature dependence of the saturated vapor pressures, fusion and vaporization enthalpies were determined using differential and fast scanning calorimetry and verified using the estimates based on solution calorimetry. The structural features of 1,3,5-tris-(α-naphthyl)benzene are discussed based on the computations performed and the data on the molecular refractivity. The consistency between the values obtained by independent techniques was demonstrated. The deviations in the previously published data were attributed to possible polymorphism.

This paper investigates a numerical code coupling technique to tackle multi-physics and multi-scale simulations using state-of-the-art software packages that typically address some specific modeling domain. The coupling considers the in-house FEM code, FEMuS, and the FVM code OpenFOAM, by exploiting the MED library from the SALOME platform. The present approach is tested on a buoyancy-driven fluid flow within a square cavity, where the buoyancy force constitutes the coupling term. In uncoupled scenarios, momentum and temperature equations are solved both in FEM and FVM codes without data exchange. In the coupled setting, only the OpenFOAM velocity and the FEMuS temperature fields are solved separately and shared at each time step (or vice versa). The MED library handles the coupling with the addition of suitable ad-hoc data structures that perform the field transfer between codes. Different Rayleigh numbers are investigated, comparing the outcomes of coupled and uncoupled cases with reference literature results. Additionally, a boundary data transfer application is presented to extend the capabilities of the coupling algorithm to coupled applications with separate domains. In this problem, the two domains share interfaces and boundary values on specific fields as fluxes are exchanged between the two numerical codes.

Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, researchers developed efficient aqueous nanofluid conductors. Carbon nanotubes (CNTs) are widely studied to reach efficient, stable, low-cost and environmentally-friendly aqueous-nanofluids. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain literature mechanisms behind improvement. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluids as desired.

The regulation of cell death is a fundamental issue in cell biology and continues to be intensely investigated worldwide. The significance of research in this field persists because understanding the determinants of cell lifespan directly impacts the maintenance of multicellular organism homeostasis and, consequently, is crucial for addressing biomedical challenges associated with various diseases. It is recognized that the initiation of cell death can be prompted by both specific signals (such as cytokines or hormones) and nonspecific stimuli, including radiation, temperature increase, or oxidants. When these factors affect a cell, numerous signaling pathways are triggered in the cell, leading to neutralization of the effects of their negative effects or, in case of irreparable damage, to cell elimination. This removal of damaged cells occurs through apoptosis or programmed cell death, a highly regulated process. Numerous signaling molecules participate in orchestrating the apoptotic process, many of which also govern other essential functions within the organism. Physiological factors capable of triggering the apoptotic program in cells include nitric oxide (NO), which serves as one of the key signaling molecules regulating the functions of the cardiovascular, nervous, and immune systems of the organism. The unique chemical nature of NO, along with its numerous intracellular targets and physiologically active redox forms, raises questions about the specific mechanisms through which NO exerts its damaging effects on cells. Utilizing pharmacological preparations- such as sources (donors) of exogenous nitric oxide- represents an approach to investigating the initiation and execution of the apoptotic program in sensitive target cells. Furthermore, this approach holds promise as a direction for discovering new selective drugs.

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

Dissimilar welds between ferritic and austenitic steels represent a good solution for exploiting the best performance of stainless steels at high and low temperatures and in aggressive environments, while minimizing costs. Therefore, they are widely used in nuclear and petrochemical plants, however, due to the different properties of the steels involved, the welding process can be challenging. Fusion welding can be specifically addressed to connect low-carbon, or low-alloy steels, with high-alloy steels, which have similar melting point. Welding of thick plates can be performed with electric arc in multiple passes or in a single pass by means of a laser beam equipment. Since microstructure and consequently mechanical properties of the weld are closely related to composition, the choice of the filler metal and processing parameters, which in turn affects the dilution rate, plays a fundamental role. Numerous technical solutions were proposed for welding dissimilar steels and much research was developed on the weldment metallurgy; therefore, this article is aimed at a review of the most recent scientific literature on the issues relating to the fusion welding of ferritic / austenitic steels. Two specific sections are dedicated respectively to electric arc and laser beam welding; finally, metallurgical issues, related to dilution and thermal field are debated in the discussion section.

Remote sensing technologies are critical for analyzing the escalating impacts of global climate change and increasing urbanization, providing vital insights into land surface temperature (LST), land use and cover (LULC) changes, and the identification of urban heat island (UHI) and surface urban heat island (SUHI) phenomena. This research focuses on the nexus between LULC alterations and variations in LST and air temperature (Tair), with a specific emphasis on the intensified SUHI effect in Kharkiv, Ukraine. Employing an integrated approach, the study analyzes time-series data from Landsat and MODIS satellites, alongside Tair climate records, utilizing machine learning techniques and linear regression analysis. Key findings indicate a statistically significant upward trend in Tair and LST during summer months from 1984 to 2023, with a notable positive correlation between Tair and LST across both datasets. MODIS data exhibit a stronger correlation R² = 0.879, compared to Landsat R² = 0.663. The application of supervised classification through Random Forest algorithms and vegetation indices on LULC data reveals significant alterations, manifested as a 70.3% increase in urban land, concurrently with a decrement in vegetative cover, especially 15.5% reduction in dense vegetation and a 62.9% decrease in sparse vegetation. Change detection analysis elucidates a 24.6% conversion of sparse vegetation into urban land, underscoring a pronounced trajectory towards urbanization. Temporal and seasonal LST variations across different LULC classes were analyzed using kernel density estimation (KDE) and boxplot analysis. Urban areas and sparse vegetation had the smallest average LST fluctuations, at 2.09°C and 2.16°C, respectively, but recorded the most extreme LST values. Water and dense vegetation classes exhibited slightly larger fluctuations of 2.30°C and 2.24°C, with the bare land class showing the highest fluctuation 2.46°C, but fewer extremes. Quantitative analysis with the application of Kolmogorov-Smirnov tests across various LULC classes substantiated the normality of LST distributions p > 0.05 for both monthly and annual data sets. Conversely, the Shapiro-Wilk test validated the normal distribution hypothesis exclusively for monthly data, indicating deviations from normality in the annual data. Thresholded LST classifies urban and bare lands as warmest classes with 39.51°C, 38.20°C and water by 35.96°C and dense vegetation 35.52°C, sparse vegetation 37.71°C as coldest, a trend consistent annually and monthly. The analysis of SUHI effects demonstrates an increasing trend in UHI intensity, with statistical trends indicating a growth in average SUHI values over time. This comprehensive study underscores the critical role of remote sensing in understanding and addressing the impacts of climate change and urbanization on local and global climates, emphasizing the need for sustainable urban planning and green infrastructure to mitigate UHI effects.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

The well-being and sociability of individuals have always been part of modernity. The development of new technologies that meet these aspirations is receiving increasing attention. Thus, strengthening the desired objectives of these tools and minimizing their undesirable side effects is the subject of a growing commitment. The present contribution aims, in this context, to evaluate and analyze the desired and undesirable effects of the interaction of electromagnetic fields with living tissues in general. This involves routines reinforcing expected functions as well as those controlling and protecting against undesirable effects. First, the interactions of electromagnetic fields with tissues are analyzed, involving their thermal biological effects of desired and undesired exposures. The roles of blood and sap fluids in bio-affected tissues are then analyzed. Secondly, the governing electromagnetic, bio-heat equations, and their coupled solution are studied. Third, the thermal behavior of tissues and the exposure adverse effects are examined. Next, monitoring and defending of the effects of exposures are discussed. This contribution illustrates and discusses mathematical modeling routines based on a generalized interaction of electromagnetic fields with living tissues.

Parkinson’s disease (PD) is the second-most common neurodegenerative disorder worldwide and is diagnosed based upon motor impairments. Non-motor symptoms are well-recognized in PD, and peripheral neuropathy is a frequent but poorly appreciated non-motor sign. Study of how the central and peripheral sensory systems are affected can contribute to the development of targeted therapies and deepen the understanding of the pathophysiology of PD. Although the cause of sporadic PD is unknown, chronic exposure to the pesticide rotenone in humans increases the risk of development of PD. Here, we aimed to investigate whether peripheral neuropathy is present in a traditional model of PD. Mice receiving intrastriatal rotenone showed greatly reduced dopamine terminals in the striatum and reduction in tyrosine hydroxylase-positive neurons in the Substantia nigra pars compacta and developed progressive motor impairments in hindlimb stepping and rotarod but no change in spontaneous activity. Interestingly, repeated testing using gold-standard protocols showed no change in gut motility, a well-known non-motor symptom of PD. Importantly, we did not observe any change in heat, cold, or touch sensitivity, again based upon repeated testing with well-validated protocols that were statistically well-powered. Therefore, this traditional model fails to replicate PD, and our data again reiterate the importance of the periphery to the disorder that is PD.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

In this paper, comprehensive analysis of combined effect of major influencing parameters on heat transfer in the single U-tube BHE (sBHE) and double U-tube BHE (dBHE) with two independent circuits was performed by using validated numerical heat transfer model. Geometrical parameters, such as shank spacing (with maximum, average and minimum values) and borehole diameter (large, medium and small borehole sizes) and borehole depth (shallow, average and deep borehole depths) as well as thermal conductivity of soil and grout which ranges from minimum to high value were considered. The combined impact of these parameters was included under four major cases: 1) combined effect of borehole depth, borehole size and shank spacing; 2) combined effect of borehole depth, and soil and grout thermal conductivity; 3) combined effect of soil and grout thermal conductivity and borehole size; and 4) combined effect of soil thermal conductivity, borehole size and shank spacing. Each of these major cases has nine different design options of both sBHE and dBHE. Series of results of heat transfer per unit borehole depth were generated for all the considered various cases. With the given parameters, the BHE case that provides highest heat transfer among the various cases of sBHE and dBHE were obtained.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

Technology is in the way to reach in its climax but the basic understanding of science in many phenomena is still awaited even though the nature witnesses it. Scientific research reveals strong analogy between photon and electron. When an atom deals neutral state, it levitates electron of outer ring from the back surface while placing the bit-energy at front surface. Gravitation behavior of that electron starts at the centre of relaxation point by including the force of side pole where the pulling force of nearby unfilled state of that atom from the front surface results into depict forcing energy shape like Gaussian distribution symbol with both ends turned called unit photon. The inertia is being involved at each stage of changing direction of that electron by introducing the disappearances of forces of two poles against the appearances of forces of two opposite poles during rest to motion and motion to rest in the first half-cycle. The same is the case in the second half-cycle of that electron during rest to motion and motion to rest but it is under different introduction of the disappearances of forces against appearances of forces. However, at stage of levitating or gravitating period of electron, only one force is being involved at one time where the opposite force is disappeared. The uninterrupted confined inter-state electron-dynamics of atom under the availability of several bits of bit-energy results into generate forcing energy shape like a wave. Two bits of bit-energy where shape of bit for first half-cycle is like integral symbol and second half-cycle is like opposite integral symbol which are being placed along the configuring trajectory of inter-state electron-dynamics during forward-direction cycle and two bits of bit-energy shape in opposite order are being placed along the trajectory of inter-state electron-dynamics during back-direction cycle. Generating forcing energy of unit photon in each cycle is pushing to the rear side by remaining connected till the electron is not restoring the state of rest. Silicon atom is considered as a model system under neutral state. Uninterrupted confined inter-state electron-dynamics result into generate forcing energy that can travel immeasurable length and unavailability of necessitating bit-energy at any interrupted stage result into generate an overt photon. Inter-state electron-dynamics for at least two cycles generate an overt photon –a photon length twice to unit photon. Under certain interaction of unit photon, it divides equally into two bits of bit-energy instead of dividing into tits and bits of heat. The mechanism of generating photon characteristic current by the electron of neutral state atom validates that atoms are four-dimensional discs at centre of dealing no force. An isolated electron is being grounded under directed forcing energy to impinge a neutral state atom where the gained instantaneous velocity under merged energy resulting into distort atom at that point. Matter changes the role of energy and force under various sorts of interactions. Here, heat energy and photon energy explore matter at atomic and electron levels, thus, devise basis of science to describe.

A novel concept of a finned piston system is presented and analyzed where the compression heat is continuously extracted from the compression chamber. The resulting compression characteristic moves in direction of an isothermal process, reducing so the temperature of the compressed fluid in the compression chamber and reducing the necessary mechanical work for the process. The finned piston concept consists in an integrated heat exchanger inside of the chamber and being constituated of imbricated flat fins placed on the stator part and on the mobile piston. The internal heat exchange surface is strongly increased in comparison with a classical piston/cylinder. The energetic performance of the new system is evaluated with the help of simulation. Pressures, forces and temperature of the compressed gas are simulated as well as the mechanical work needed. The different curves are compared with adiabatic and isothermal characteristics.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Abscisic acid (ABA) is a conserved “stress hormone” in unicellular organisms, plants and animals. In mammals, ABA and its receptors LANCL1 and LANCL2 stimulate insulin-independent cell glucose uptake and oxidative metabolism: overexpression of LANCL1/2 increases, and their si-lencing conversely reduces, mitochondrial number, respiration and proton gradient dissipation in muscle cells and in brown adipocytes. We hypothesized that the ABA/LANCL hor-mone/receptors system could be involved in thermogenesis. Heat production by LANCL1/2-overexpressing vs. double-silenced cells was compared in rat H9c2 cardiomyocytes with two different methods: differential temperature measurements using sensitive thermistor probes, and differential isothermal calorimetry. Results indicate that overexpressing cells generate an approx. double amount of thermal power compared with double-silenced cells, and that addition of ABA further doubles heat production in overexpressing cells. With the temperature probes, we find a time-scale of approx. 4 min for thermogenesis to “turn on” after nutrient addition. These results identify the ABA/LANCL hormone receptors system as a hitherto unknown regu-lator of cell thermogenesis. Pharmacologic means of increasing metabolic energy dissipation are considered a promising strategy to reduce oxidative stress and lipid accumulation at a cellular and organismic level: from this study, LANCL1-2 proteins emerge as targetable controllers of ther-mogenesis through their natural ligand ABA.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

This author is not a philosopher nor historian of science, but an engineering thermodynamicist. In that regard and in addition to various philosophical “why & how” treatises and existing historical analyses, the physical and logical “what it is” reflections, as successive Key Points, where a key reasoning infers the next one, along with novel contributions and original generalizations, are presented. We need to keep in mind that in Sadi Carnot’s time (early 1800s) the steam engines were inefficient (below 5%, so the heat in and out were comparable within experimental uncertainty), the conservation of caloric flourished (might be a fortunate misconception), and many critical thermal-concepts, including the conservation of energy (The First Law) were not even established. If Clausius and Kelvin were "fathers of thermodynamics" then Sadi Carnot was the "grandfather" [Kostic, 2023 July 24], or better yet, Sadi Carnot was the "Forefather of Thermodynamics-to-become" [Kostic, 2023 October 29].

An extensive thermodynamic study of N-methylformamide (CAS RN: 123-39-7) and N,N-dimethylformamide (CAS RN: 68-12-2), is presented in this work. The liquid heat capacities of N-methylformamide were measured by Tian–Calvet calorimetry in the temperature interval (250 – 300) K. The vapor pressures for N-methylformamide and N,N-dimethylformamide were measured using static method in the temperature range 238 K to 308 K. The ideal-gas thermo-dynamic properties were calculated using a combination of the density functional theory (DFT) and statistical thermodynamics. A consistent thermodynamic description was developed using the method of simultaneous correlation, where the experimental and selected titerature data for vapor pressures, vaporization enthalpies, and liquid phase heat capacities and calculated ide-al-gas heat capacities are treated together to ensure overall thermodynamic consistency of the results. Resulting vapor pressure equation is valid from the triple point to the normal boiling point temperature.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

This study investigates the application of regression neural networks, in particular the fitrnet model, in predicting the hardness of steels. The experiments involve extensive tuning of hyperparameters using Bayesian optimization and employ 5-fold and 10-fold cross-validation schemes. The trained models are rigorously evaluated, and their performances are compared using various metrics such as mean square error (MSE), root mean square error (RMSE), mean absolute error (MAE), and coefficient of determination (R2). The results provide valuable insights into the effectiveness of the models and their ability to generalize to unseen data. In particular, Model 4208 (8-85-141-1) emerges as the top performer with an impressive RMSE of 1.0790 and an R² of 0.9900. The research paper contains an illustrative example that demonstrates the practical application of the developed model in determining the hardenability band for a specific steel grade and shows the effectiveness of the model in predicting and optimizing heat treatment results.

Heat stress results in significant economic losses to the poultry industry. Genetics plays an important role in chickens adapting to the warming environment. Physiological parameters, including hematochemical parameters, change in response to heat stress in chickens. To explore the genetics of heat stress resilience in chickens, a genome-wide association study (GWAS) was conducted using Hy-Line Brown (HLB) layer chicks treated with either high ambient temperature or combined high temperature and Newcastle disease virus (NDV) infection. Hematochemical parameters were measured during three treatment phases: acute heat stress, chronic heat stress, and chronic heat stress combined with NDV infection. Significant changes in blood parameters were recorded for 11 parameters across the three treatments. The GWAS revealed 39 significant SNPs (P < 0.05) for 7 parameters, located on Gallus gallus chromosomes (GGA) 1, 3, 4, 6, 11, and 12. The significant genomic regions were further investigated to examine if the genes within the regions were associated with the corresponding traits under heat stress. A candidate gene list including genes in the identified genomic regions that were also differentially expressed in chicken tissues under heat stress was generated. Understanding the correlation between genetic variants and resilience to heat stress is an important step in improving heat tolerance in poultry.

The electrification of process industries is one of the main challenges when building a low-carbon society since they consume huge amounts of fossil fuel generating different emissions. Heat pumps are one of the instruments to perform industrial sector of carbon-neutral market players. This paper proposes an approach to improve the economic feasibility of heat pumps within the process plants. Initial energy targeting with Grand Composite Curves was used and supplemented with the detailed design of the evaporator and compressor for different condensation and evaporation pressures. The trade-off between the capital cost of the heat pump and the electricity cost was investigated and optimal configurations were selected. The case study investigates the gas fractioning unit of a polymer plant where three heat pumps were integrated into distillation columns. The results demonstrated that the heat recovery is 174 MW and requires an additional 37.9 MW of electricity to reduce hot utility by 212 MW. The selection of evaporation and condensation pressure of heat pumps allows saving of 21.5 M€/y for 7 years of plant operation.

Regeneratively cooled scramjet has already been successfully verified as propulsion device for hypersonic vehicle. As a result, dynamic process of flow and heat transfer in cooling channel is commonly occurred which may bring hazard and control difficulties for scramjet. To study transient flow and heat transfer process in cooling channel, a dynamic numerical model is established. Dynamic characteristics of flow and heat transfer under different conditions are calculated and discussed, which includes change of inlet fuel mass flow, heat flux and pressure working conditions. Results show that stable time of cooling channel outlet fuel temperature is related to the change rate of inlet mass flow and heat flux. The stable time of outlet fuel temperature under heat flux decreasing working conditions are about 12.5 s. The initial response of working pressure fluctuation will lead to fuel temperature fluctuation, which has little effect on wall temperature.

Designing high-voltage underground transmission lines poses complex challenges in heat management, trench optimization, and determining cable ampacity. This article introduces an innovative proposal that focuses on adjusting the dimensions of the thermal backfill as a primary strategy to enhance ampacity compared to the traditional approach of increasing the cross-sectional area of the cable core. The methodology employs a particle swarm optimization (PSO) technique with adaptive penalization, restart strategies, and parameter self-adaptation implemented in MATLAB. The objective of this approach is to provide more efficient solutions than traditional MATLAB PSO, demonstrating improved convergence and more accurate results with a success probability of 66.1\%. Although traditional PSO is 81\% faster, the proposed PSO stands out for its precision. Additionally, the incorporation of thermal backfill results in an 18.45\% increase in cable ampacity. Variations in the thermal resistivity of the soil, backfill, and ambient temperature are highlighted as sensitive factors affecting ampacity and backfill dimensions. This method is presented as a crucial tool in the early stages of the project and underground installation in operation with maximum ampacity, contributing to the continuous improvement of energy efficiency.

Heat waves are a significant consequence of climate change threatening public health by increased morbidity and mortality. The aim of this study was to estimate individuals’ knowledge, attitudes and practice related to heat waves. We conducted an exploratory cross-sectional study in Greece during September 2023. We employed a convenience sample of 1055 participants. We used the heat wave knowledge, awareness, practice and behavior scale (HWKAPBS) to measure our outcome. We measured several socio-demographic variables, such as gender, age, educational level, etc. as potential determinants. Mean scores for the knowledge, awareness, practice and behavior factors were 12.5, 22.7, 22.2 and 12.1 respectively. Females had higher scores on the four factors compared with males. We found a positive relationship between self-perceived health status and awareness, practice and behavior about heat waves. Similarly, we identified a positive relationship between self-perceived financial status and awareness and behavior about heat waves. Increased age was associated with increased practice score, while increased educational level was associated with increased knowledge score. Additionally, behavior score was higher among participants in urban areas than those in rural areas. We found statistically significant positive correlations between the four factors. Levels of knowledge, awareness, practice and behavior about heat waves were high in our sample. Several socio-demographic variables affect participants’ knowledge, awareness, practice and behavior concerning heat waves.

“Anti-stripping Agents" or "adhesion promoters” can enhance the chemical affinity between as-phalt and aggregate by increasing their mutual attraction. Various forms of anti-stripping agents have been proposed to mitigate pavement stripping, and siloxane-based Zychotherm is one of them. Choosing the appropriate type and dose of anti-stripping additives is no doubt vital to the intended performance. Therefore, it is critically important to determine the dose of the additives used in the modification of asphalt binders. This research developed a feasible detection method that can closely measure the dose (0.05% and 0.1%) of siloxane-based anti-stripping liquid agents. Related test methods including heat combustion test, residue visualization, burning, and ignition were implemented. Heat combustion results showed that with the addition of Zychotherm anti-stripping additive, average heat combustion value decreased by 1.34% and 1.72% for 0.05% and 0.1% Zychotherm modified binder respectively. In the burning and ignition process, the modified binder leaves yellowish substances in the residue, which is an indication of the presence of Zy-chotherm. The weight of the yellowish residue relates more to the quantity of Zychotherm in as-phalt binder.

Mapping building roof plane structures is an active research direction in urban-related studies, as understanding roof structure provides essential information for generating highly detailed 3D building models. Traditional deep learning models have been the main focus of most recent research endeavours aiming to extract pixel-based building roof plane areas from remote sensing imagery. However, significant challenges arise, such as delineating complex roof boundaries and invisible boundaries. Additionally, challenges during the post-processing phase, where pix-el-based building roof plane maps are vectorized, often result in polygons with irregular shapes. In order to address this issue, this study explores a state-of-the-art method for planar graph reconstruction applied to building roof plane extraction. We propose a framework for reconstructing regularized building roof plane structures using aerial imagery and cadastral information. Our framework employs a holistic edge classification architecture based on an attention-based neural network to detect corners and edges between them from aerial imagery. Our experiments focused on three distinct study areas characterized by different roof structure topologies: Stadsveld – 't Zwering neighbourhood and Oude Markt area, located in Enschede, The Netherlands, and the Lozenets district in Sofia, Bulgaria. The outcomes of our experiments revealed that a model trained with a combined dataset of two different study areas demonstrated superior performance, capable of delineating edges obscured by shadows or canopy. Our experiment in the Oude Markt area resulted in building roof plane delineation with an F-score value of 0.43 when the model trained on the combined dataset was used. In comparison, the model trained only on the Stadsveld – 't Zwering dataset achieved an F-score value of 0.37, and the model trained only on the Lozenets dataset achieved an F-score value of 0.32. The results from the developed approach are promising and can be used for 3D city modelling in different urban settings.

The automotive industry needs to improve energy efficiency rapidly to achieve carbon neutrality while creating a safe, secure, comfortable driving environment for customers. Porous sound-absorbing materials and porous thermal insulators are typically used to satisfy these requirements despite limitations in mass and space. While these porous materials are similar, the microstructures they offer for high performance differ in the size and connectivity of their fluid phases, which enhances the difficulty of achieving excellent sound absorption and thermal insulation in the same material. In this study, a hydrophobic cellulose nanofiber–poly(methylsiloxane) xerogel composite was developed using computational microstructure modeling. This porous material has high porosity and excellent thermal insulation and sound absorption properties.

Heat stress is a serious threat to tomato production. The ultrastructure and element mapping of tomato chloroplast were investigated under different nitrogen levels to explore the regulatory effect of nitrogen on tomato chloroplast under heat stress. Experiments design two temperature treatments (25°C/15°C, as control, 40°C/30°C, as severe high-temperature, SHT ) and four nitrogen levels (0.0 kg hm-2, N1; 187.5 kg hm-2, N2; 250 kg hm-2, N3, as recommended nitrogen-application; 312.5kg hm-2 , N4) for a duration of 5 days in artificial climate chamber. The results showed that heat stress led to obvious damage to the ultrastructure of tomato chloroplast, including thylakoid stacking disorder, granum destruction, and starch grain aggregation and degradation. With the increase of nitrogen level, the ratio of long and short axes of tomato chloroplasts increased, the differentiation of chloroplasts was strengthened, the number of plastoglobuli was increased and aggregated, and the degree of damage to the ultrastructure of chloroplasts was reduced. The regulatory effect of nitrogen on the ultrastructure of tomato chloroplasts under heat stress was mainly reflected in the phosphorylation degradation process of starch granules in chloroplasts. There are obvious segmentation lines of Ca, P and Cl on both sides of the inner and outer chloroplasts, and enriched in the chloroplasts, which can outline the boundary of the chloroplasts. Element mapping analysis revealed that heat stress significantly increased the contents of calcium, phosphorus and chlorine in the chloroplast of tomato leaves, while the contents of potassium was decreased. The application of nitrogen fertilizer could significantly regulate the element distribution of tomato chloroplast under heat stress, especially the regulation of phosphorus, chlorine, calcium, magnesium. These results provide new insight into the role of nitrogen using TEM-EDX mapping in the protection of tomato chloroplast under heat stress and the mechanism of heat stress tolerance in plants.

In this experiment, the fermented pineapple residue (FPR) was replaced with 0% (CON), 25% (T25) and 50% (T50) in the diet based on silage royal grass roxb for 30 days in the fattened fatten bulls to evaluate the effect of FPR on growth performance, serum indicators and rumen characteristics.Thirty Simmental calves were selected and divided into three groups according to a completely random design.The temperature and humidity of the cowshed shall be measured every day.Rectal temperature and blood of cattle were measured, and blood and immune markers were measured.The results showed that the rectal temperature decreased significantly when adding 25% fermented pineapple residue (P&lt;0.05), and the rectal temperature decreased significantly when adding 50% fermented pineapple residue (P&lt;0.01).The content of T4 and TC in serum of cattle in T50 group was significantly lower than that in the control group (P&lt;0.01), and the content of T3 was significantly higher than that in the control group (P&lt;0.05), and the content of CR was significantly lower than that in the control group (P&lt;0.01). Fermented pineapple residue can indeed improve the oxidative (heat) stress resistance of finishing cattle. In the correlation experiment, bacterial genera such as Succinniclassicum, Melainabacteria, Lachnospiraceae, and Fibrobacteres all showed significant or extremely significant correlations with heat stress-related indicators.

Heat-stressed lactating dairy cattle exhibit unique metabolic symptoms; many of which are undoubtedly involved in heat-induced subfertility. Because of its known systemic effects, we hypothesized that γ-aminobutyric acid (GABA) participates in the regulation of insulin and progesterone during heat stress. Multiparous lactating Holstein cows (n=6) were studied during four experimental periods: 1) thermoneutral (TN; d 1-5), 2) TN + hyperinsulinemic-hypoglycemic clamp (d 6-10), 3) heat stress (HS; d 16-20), and 4) HS + euglycemic clamp (d 21-25). Blood samples were collected once daily via coccygeal venipuncture into heparinized evacuated tubes. Analysis of GABA concentrations from all four treatment periods yielded no differences. In direct comparison to TN concentrations, plasma GABA tended to be decreased during HS (16.57±2.64 vs 13.87±2.28 ng/ml, respectively, P = 0.06). Both milk production and plasma insulin were moderately correlated with plasma GABA (r=0.35, P<0.01; r = -0.32, P<0.01). Plasma progesterone was correlated with plasma GABA concentrations during TN but not HS. These results are the first to indicate that peripheral GABA could be involved in regulating aspects of production and reproduction during heat stress. More research is needed to determine its precise role(s).

The solar heat pump system based on photovoltaic photothermal (PV/T) modules is a new technology that integrates photovoltaics and heat reutilization. It can improve the efficiency of photovoltaic conversion and recovery the remaining heat generated during the photoelectric conversion process, thereby improving the comprehensive efficiency of the whole system. Simulink software is a visual simulation tool, which has the advantages of strong applicability, clear simulation structure and calculation process. The design of its graphical programming greatly simplifies the user modeling process and allows for direct viewing of results, therefore improving the simulation efficiency. At present, there is little research on simulation of solar heat pump systems with PV/T modules based on Simulink software. In this paper, the mathematical models of each component contained in the PV/T solar heat pump system were established based on the system working principle, energy conservation equations and some empirical formulas, and then the operation of the system was simulated by the Simulink software. Due to the operation characteristic of PV/T modules is the key influencing factor for the whole system performance, the model and simulation process for PV/T modules were introduced in detail. The results showed that the surface temperature of PV/T modules under different operating conditions was significantly lower than that of ordinary photovoltaic panels, and the temperature change amplitude was lower. As results, the power generation and photovoltaic conversion efficiency were significantly improved.

Pool boiling heat transfer is recognized as one of the most effective heat transfer methods and has extensive applications in industry. The application of non-azeotropic binary mixtures can not only meet the environmental requirements of modern industrial development, but also improve the coefficient of performance (COP) of many systems. Therefore, studying the boiling heat transfer characteristics of non-azeotropic mixtures is important on improving their potential industrial application. This article selected ethylene glycol/deionized water (EG/DW) at varies concentration as the research working fluids, and conducted experimental research on the pool boiling performance. At the same time, the thermophysical parameters of the mixtures were studied and analyzed. The results showed that the concentration of EG in the mixture had a significant impact on the thermal properties and temperature glide of the mixture, where both affected the heat transfer deterioration. Based on experimental data, six widely used heat transfer coefficient prediction correlations were used for calculation, and two of them were modified. The deviation between the modified correlations and the experimental results remained within 20%.

This work presents a heat transfer and boiling model that computes the evolution of the temperature field in a representative steel workpiece quenched from 850 or 930°C by immersion in water flowing at average velocities of 0.2 or 0.6 m/s, respectively. Under these conditions, all three boiling regimes were present during cooling: stable vapor film, nucleate boiling, and single-phase convection. The model was based on the numerical solution of the heat conduction equation coupled to the solution of the energy and momentum equations for water. The mixture phase approach was adopted using the Lee model to compute the rates of water evaporation-condensation. Heat flux at the wall was calculated for all regimes using a single semi-mechanistic model. Therefore, evolution of boiling regimes at every position on the wall surface was automatically determined. Predictions were validated using laboratory results, namely: a) Videorecording the upward motion of the wetting front along the workpiece wall surface, and b) cooling curves obtained with embedded thermocouples in the steel probe. Wall heat flux calculations were used to determine the importance of the simultaneous presence of all three boiling regimes on the heat flux distribution. It was found that this simultaneous presence leads to high heat flux variations that should be avoided in production lines.

Background: Musculoskeletal pain is a non-negligible multifaceted condition affecting more than 30% of the global population. Superficial heat therapy (HT) through increasing tissues temperatures plays a role in increasing local metabolism and function and relieving pain. Knee pain and sports represent two relevant fields of superficial HT application. Methods: In the present paper a panel of experts performed a narrative review of the literature regarding the role of superficial HT in the management of knee pain and sport activities. Results: According to the reviewed literature, HT represents a therapeutic option in the management of musculoskeletal pain due to three main effects: pain relief, promotion of healing and return to normal function and activity. Moreover, HT plays a role in sport activities both before and after exercise. Before performing sports, HT helps in preparing muscles for performance. After performing sports, it is capable to promote recovery and healing pathways. Combining and sequencing superficial heat and cold therapy represent an interesting topic of study. Overall, application of heat wraps for superficial HT can be considered safe. Conclusions: Despite being an ancient method, HT shows to be a potentially beneficial and safe option in the management of several conditions including KP and sports. The key in the application of superficial HT is a multimodal and multidisciplinary approach.

The ability to control the temperature distribution T(t,r) and the rate of temperature change Rt,r inside glasses is important for their microstructuring. The lattice temperature is considered at time t, exceeding the electron-phonon thermalization time, and at a distance r from the center of the model spherical heating zone. In order to describe thermal excitations, the heat capacity of glasses must be considered as a function of time due to its long-term relaxation. A method for analytical calculation of T(t,r) and R(t,r) for glasses with dynamic heat capacity cdyn(t) is proposed. It is shown that during laser microstructuring the local cooling rate -R(t,r) significantly depends on the time dispersion of cdyn(t). It has been established that at the periphery of the model heating zone of the laser beam focus, the local cooling rate can reach more than 1011 K/s. Strong cooling rate gradients were found at the periphery of the heating zone, affecting the microstructure of the material. This effect is significantly enhanced by the time dispersion of cdyn(t). The effect associated with this time dispersion is significant even well above the glass transition temperature Tg, since even short relaxation times of the dynamic heat capacity cdyn(t) are significant.

The purpose of this study was to 1) examine the impact of various types of heat processing used by consumers (water bath cooking WBC, oven convection roasting OCR, grilling G, pan frying PF) on the selenium content and its retention in goose breast meat (with and without skin); 2) Estimation of coverage of this element's daily requirement in adults after consuming 100 g of goose breast meat. The material used in the study comprised 36 breast muscles cut from carcasses of 17-week-old White Koluda geese. The moisture, ash, and selenium were determined in both raw and thermally processed muscles. It has been concluded that various methods of heat processing significantly impact cooking loss, moisture, ash and selenium content of meat. The heat processing increased the selenium content of the muscle regardless of the presence of skin, which affects the possibility of covering adults' Nutrient Reference Values-Requirements (NRV-R) for this element in the range of 33.3-44.8%. Goose breast meat can be a valuable component of a diversified diet. It provides many nutrients. It is also a safe source of selenium. It is unlikely that adult consumers, even those who eat goose regularly, will exceed this element's upper tolerable intake level.

A thermal system in very deep Lake Tazawa (maximum depth, 423 m) was investigated by estimating the heat budget. In the heat budget estimate, the net heat input at lake surface and the heat input by river inflow and groundwater inflow were considered. Then, the heat loss by snowfall onto lake surface was taken into account. Meanwhile, lake water temperature was monitored at 0.2 m to the bottom by mooring temperature loggers for more than two years. The heat storage change of the lake from the loggers was calibrated by frequent vertical measurements of water temperature at every 0.1 m pitch by a profiler with high accuracy (± 0.01 °C). The heat storage change (W/m2) obtained by the temperature loggers reasonably accords to that from the heat budget estimate. In the heat budget, the net heat input at lake surface dominates the heat storage change, but the significant heat loss by river inflow sporadically occurred, which is caused by the relatively large discharge from a reservoir in the upper region. How deep the vertical water circulation in the lake occurs in winter was judged by the differences between water temperatures at 0.2 m depth and bottom and between vertical profiles of dissolved oxygen over winter. It is strongly suggested that the whole water circulation does not occur every winter, if any, very weak.

Ontological premises have profound theoretical implications. This analysis posits a single, universal structure composed of two ontic entities: discrete, quantized units of space ("Planck Spheres") and a State of Absolute Nothingness (the "SOAN"). Planck Spheres and the SOAN form a physical, ultra-high (3 x N) dimensional space ("Planck Space") and a discrete 3D space (or "4D spacetime"). Together, Planck Space and 4D spacetime form a tightly integrated ((3 x N) + 3) hyperspace (the "Dual Ontology"). Critically, a one-to-one mapping and identity exists between the Planck Spheres comprising 4D spacetime and Planck Space. The Dual Ontology conjecture supports radically simplified physical explanations for three distinct areas of theoretical physics: First, the conjecture reconciles fundamental issues in Special Relativity and quantum mechanics by explaining why single and N-body quantum states (a) dynamically evolve in 4D spacetime subject to the speed of light and (b) instantaneously collapse in a physical Planck Space that is not subject to Special Relativity. Second, the temporal and physical asymmetry between the dynamic evolution of quantum states in 4D spacetime subject to Special Relativity and the instantaneous collapse of quantum states in a Planck Space where Special Relativity is inapplicable explains quantum path irreversibility and the arrow of time. Third, at or near the heat death of 4D spacetime, the instantaneous collapse of the energy content of Planck Space and the simultaneous transition of 4D spacetime's extremely widely dispersed energy content to a non-singular, generally localized volume at t = 0 explains 4D spacetime's isotropy, homogeneity, extremely high energy, pressure, and temperature, flatness, and low gravitational entropy. It also explains the horizon and fine-tuning problems.

The urban heat island (UHI) and its intensity is one of the phenomena that are of determining importance for the comfort of living in cities and their sustainable development in the face of deepening climate change. The study is objectively difficult due to the large dynamics like land cover and the considerable diversity of land use patterns in urban areas. Various approaches and methods are used in research practice, based both on ground measurements and in the use of remote methods and satellite information. However, most of these approaches provide information with problematic spatial and temporal resolution, making them difficult to apply for sustainable urban planning purposes, which require adequate information provision. This paper presents the results of the application of thermal photogrammetry based on the use of unmanned aerial systems (UAS), combined with geographic information systems (GIS), in the study of surface urban heat island intensity (SUHI), at the local level for the largest housing complex in Bulgaria - Lyulin district of the capital of Sofia city. The studies were carried out during a heat wave in July 2023. A difference of 16.5oC was found between locations with SUHI occurrence and suburban areas. The information benefits of locally addressed data and their direct applicability are discussed to support decision-making processes in the planning and management of urban areas, including their climate adaptation and sustainable development.

Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

In pursuit of sustainable human survival, the effective utilization of renewable energy has become critical to technological advancement. Ocean Thermal Energy Conversion (OTEC) technology, which generates electricity by leveraging the temperature differential between surface and deep ocean waters, enables stable power generation around the clock. In this domain, the combination of thermoelectric generators (TEGs) and heat exchangers has exhibited immense potential for ameliorating the deficiencies of conventional OTEC. This study uses numerical simulation to investigate the fluid dynamics characteristics of heat exchangers with flat fins and different types of longitudinal vortex generators (LVGs) under the same number of fins. The research encompasses heat exchangers with rectangular, triangular, and trapezoidal LVGs. Concurrently, the analysis examines how the vortices generated by the LVGs influence the thermoelectric performance of the TEGs. The results demonstrate that heat exchangers integrating flat fins and LVGs can enhance the power generation efficiency of TEGs. However, the pumping power required by the LVGs constrains the thermoelectric conversion efficiency. Compared to rectangular and triangular LVGs, trapezoidal LVGs achieve a superior balance between output and pumping power. Heat exchangers utilizing trapezoidal LVGs can attain the highest TEG thermoelectric conversion efficiency with a specific seawater flow velocity. Overall, these findings provide valuable reference information for applying TEGs and heat exchangers in OTEC design.

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

This paper presents a comprehensive study on the application and optimization of automotive thermoelectric generators (ATEGs), focusing on the crucial role of heat exchangers in enhancing energy conversion efficiency. Recognizing the substantial waste of thermal energy in internal combustion engines, our research delves into the potential of TEGs to convert engine waste heat into electrical energy, thereby improving fuel efficiency and reducing environmental impact. We meticulously analyze various heat exchanger designs, assessing their influence on the TEG's output power under different exhaust gas flow rates and temperatures. Furthermore, we explore the impact of TEG material properties on the overall energy conversion effectiveness. Our findings reveal that specific heat exchanger designs significantly enhance the efficiency of waste gas heat exchange, leading to an improved performance of the TEG system. We also highlight the importance of thermal insulation in maximizing TEG output. This study not only contributes to the ongoing efforts to develop more sustainable and efficient vehicles but also provides valuable insights into the practical application of thermoelectric technology in automotive engineering. Through this research, we aim to pave the way for more environmentally friendly transportation solutions, aligning with global efforts to reduce fossil fuel dependence and mitigate environmental pollution.

The thermoelectric generator (TEG) has much potential as a renewable energy technology that could be used in ocean thermal energy conversion (OTEC). This technique employs TEGs and heat exchangers as substitutes for the intricate elements found in conventional OTEC systems, including pressure valves, evaporators, condensers, and turbine generators. By harnessing the temperature difference between warm surface seawater and cold deep seawater, it facilitates the conversion of this thermal gradient into electrical energy. This study used computer simulations to look at and compare three different types of heat exchangers: a cavity-type heat exchanger, a heat exchanger with flat fins, and a heat exchanger with longitudinal vortex generators (LVGs). The objective was to evaluate the influence of these designs on the thermoelectric conversion performance when implemented in OTEC systems. The study's findings indicate that using heat exchanger configurations featuring flat fins, or LVGs, enhances the efficiency of thermal energy transfer from warm seawater to TEGs, resulting in a notable enhancement in the output power of TEGs. Furthermore, the efficiency of TEG thermoelectric conversion is influenced by varying seawater flow rates in relation to the performance of flat fins and LVGs. In contrast to the cavity-type heat exchanger, the utilization of a heat exchanger equipped with flat fins has been found to yield a notable enhancement in the output power of TEGs by approximately 22.92%. Furthermore, this configuration demonstrates a substantial improvement in thermoelectric conversion efficiency, exhibiting an increase of around 40.01%. These improvements are observed under certain conditions pertaining to flow rates and fin heights. Utilizing heat exchangers equipped with LVGs has been found to enhance the output power of TEGs by 13.02% and improve the overall thermoelectric conversion efficiency by 17.72%. These improvements are observed under certain conditions, including specific flow rates, LVG tilt angles, and locations.

A new biodegradable paper-based film is a hot research topic in the development of green agriculture. In this paper, a black paper base film coated with cooked tung oil with excellent mechanical properties, hydrophobic surface, high heat transfer and strong weather resistance was prepared by spraying high pigment carbon black solution on the surface of base paper. The results showed that the surface solidified oil film with rough structure was made by the brush coating process of cooked tung oil, and the base film of black paper was given hydrophobic structure, and the contact angle reached 98.9 °. Cooked tung oil permeates into the inside of the paper base, and after curing, it forms a multi-dimensional network film structure. The maximum tensile stress of the black paper base film is about 123% higher than that of the original paper base film. The coloring of carbon black makes the black paper base film have heat conduction effect, and the average heat transfer rate reaches 15.12 °C/s. Cooked tung oil is combined with the paper-based fiber high-toughness layer to form a stable system. The existence of the cured film improves the basic mechanics and hydrophobicity, and the resistance to ultraviolet radiation and hot air is greatly improved. This study provides a feasible scheme for the application of a black paper base film coated with cooked tung oil.

Given the context of global climate change, a worldwide increase in land surface temperature (LST) is anticipated, leading to the exacerbation and broadening of its impacts. This could jeopardize the environmental conditions in countries with a predominantly hot and harsh climate, such as Bahrain, one of the Cooperation Countries (GCC) nations. Conversely, Bahrain is currently experiencing significant population growth, leading to a surge in demand for land to accommodate the construction of additional residential developments. This circumstance allows investigation of the potential impact of land use and land cover alterations on the variation in Land Surface Temperature (LST). In order to accomplish this objective, a residential development project was executed within the timeframe spanning from 2013 to 2023. Four sets of Landsat 8 OLI/TIRS remote sensing datasets were selected, with each set corresponding to one of the four climate seasons. Each set consisted of two images: one capturing the study area before the commencement of the development process and the other depicting the study area after the completion of the development. The study area was analyzed by extracting the land surface temperature (LST), normalized difference vegetation index (NDVI), and normalized difference built-up index (NDBI) on various dates. Subsequently, correlation and regression analysis were employed to examine the interrelationships among these three variables. The findings demonstrated a notable rise in the mean land surface temperature throughout the spring and autumn seasons following the conclusion of land development activities. The findings indicate a positive and robust association between LST and NDBI across all seasons. Moreover, this relationship strengthened following the completion of development activities in the area. Conversely, there was a negative correlation between LST and NDVI prior to the region's development, which transformed into a positive relationship post-development. These results provide empirical support for the notion that small-scale residential developments contribute to a notable increase in LST, primarily driven by the expansion of impervious surfaces in built-up areas. The findings can potentially contribute to the formulation of localized adaptation strategies for small-scale residential development projects.

Indoor comfort is a critical determinant of the holistic educational experience, significantly influencing the well-being, concentration, and performance of students within the confines of school environments. Despite the widespread implementation of heating, ventilation, and air conditioning (HVAC) systems in educational institutions, achieving satisfactory thermal conditions, acceptable acoustics, and optimal daylight levels for occupants continues to pose a considerable challenge. In this review, we specifically delves into the parameters characterizing Italian school environments, recognizing their direct impact on students’learning and concentration. The primary objectives of this review are conducting a thorough examination of the current acustic conditions in Italian schools. The initial phase of our search strategy involved retrieving data from key databases, namely, Scopus, Web of Science, ScienceDirect, PubMed, and Google Scholar. Following the elimination of duplicate articles (n = 289), a total of 135 distinct papers remained for analysis. A critical review of the existing literature is presented based on these criteria, offering guidelines and recommendations for forthcoming studies. The critical review underscores various shortcomings in the current design, deployment, and documentation of multi-domain studies, signaling the need for enhanced quality in future research efforts.

Annotation. The experience of using coal flotation waste (CFW) as a weakly exothermic insulating backfill for insulating the head part of forging dead-melted steel ingots is presented.It has been shown that when using weakly exothermic fills based on single-component fills in the form of CFW, it is possible to reduce the chemical heterogeneity of the ingot by producing a closed shrinkage cavity, which allows halving heat loss and depth of penetration of shrinkage looseness into the body of the ingot, reducing the segregation of impurities, compacting the head part of the ingot and increasing the yield; moreover, the profitable part of the ingot is more dense and less contaminated with nonmetallic inclusions.The studied patterns of the formation of a closed shrinkage cavity with a dense “bridge” in the head part of a dead-melted steel ingot made it possible to develop and implement a technology for casting large forging ingots of sufficiently high quality using weakly exothermic heat-insulating materials based on metallurgical waste (coke screenings, coal flotation waste)

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

Combustion parameters are the important aspects in the development and research of an internal combustion engines. Hence present work is an attempt to develop an artificial neural network (ANN) model for anticipating the combustion characteristics of computerized CI DI VCR, four strokes, single cylinder, and water cooled engine using mixture of two biodiesel and diesel blends as a fuel. The two biodiesel selected are Jatropha and Simarouba and mixed in the ratio of 75:25. Two biodiesel mixtures is used for the preparation of various blends with diesel. Experiments are carried out at different compression ratio, at different % load and blends B20, B40, B60and neat diesel (B00) fuel to accumulate the assorted combustion data. The input variables are % load, compression ratio, blends and crank angle. The outputs well thought-out are cylinder pressure (CP), net heat release rate (NHRR), cumulative heat release (CHR), rate of pressure rise (RPR), mass fraction burned (MFB) and maximum cylinder pressure. The assessment is focused on developing artificial neural network for the prediction and verifying the combustion characteristics of engine. MATLAB software is used for analysis of different combustion aspects of the engine. Multilayer neural network perceptions are used with Feed-Forward Back Propagation algorithm with performance function for mapping the input and output parameters. The experimental outcomes are compared with ANN estimated results for the analysis. The outcome from the study authenticate that experimental results are in match with ANN results. The accuracy of the ANN model shows the developed model can effectively predict the engine combustion characteristics with excellent regression coefficients ‘R’ and its values are close to unity and the mean square errors are extremely less. ANN model approach is competent towards predicting the combustion aspect of diesel engine with good accuracy

Space and water heating for residential and commercial buildings amount to a third of the European Union’s total final energy consumption. Approximately 75% of the primary energy is still produced by burning fossil fuels, leading to high greenhouse gas emissions in the heating sector. Therefore, policymakers increasingly strive to trigger investments in sustainable and low-emission heating systems. This study forms part of the “Roll-out of Deep Geothermal Energy in North-West-Europe”-project and aims at quantifying the spatial heat demand distribution in the Interreg North-West-Europe region. An open-source geographic information system and selected Python packages for advanced geospatial processing, analysis, and visualization are utilized to constrain the maps. These were combined, streamlined, and optimized within the open-source Python package PyHeatDemand. Based on national and regional heat demand input data, three maps are developed to better constrain heat demand at a high spatial resolution of 100*100m2 for the residential and commercial sectors, and for both together (in total). The developed methodology cannot only be applied to transnational heat demand mapping but also on various scales ranging from city district level to states and countries. In addition, the workflow is highly flexible working with raster data, vector data, and tabular data. Results reveal a total heat demand of the Interreg North-West-Europe region of about 1,700TWh. The spatial distribution of the heat demand follows specific patterns, where heat demand peaks are usually in metropolitan regions like for the city of Paris (1,400MWh/ha), the city of Brussels (1,300MWh/ha), the London metropolitan area (520 MWh/ha), and the Rhine-Ruhr region (500 MWh/ha). The developed maps are compared with two international projects, Hotmaps and Heat Roadmap Europe’s Pan European Thermal Atlas. The average total heat demand difference from values obtained in this study to Hotmaps and Heat Roadmap Europe is 24 MWh/ha and 84 MWh/ha, respectively. It is assumed that the implementation of real consumption data is an improvement in spatial predictability. The heat demand maps are therefore predestined to provide a conceptual first overview for decision-makers and market investors. The developed methods will further allow for anticipated mandatory municipal heat demand analyses.

Evapotranspiration (ET) is a major component of water budget in Bottomland Hardwood Forests (BHF) and is driven by a complex intertwined suite of meteorological variables. The understanding of these interdependencies leading to seasonal variations in ET is crucial in better informing water resource management in the region. We used a structural equation modeling approach to analyze the drivers of ET using Eddy covariance water and heat flux data collected from a BHF, located in the Russel Sage Wildlife Management Area (RSWMA). It consists of mature closed-canopy deciduous hardwood trees with an average canopy height of 27 m. Factor analysis was used to characterize the shared variance among drivers and path analysis was used to quantify independent contributions of individual drivers. In our results, ET and net radiation (Rn) showed similar variability patterns with Vapor Pressure Deficit (VPD) and temperature in Spring, Summer, and Autumn seasons while they differ in Winter season. The path analysis shows that Rn has the strongest influence on ET variations via direct and indirect pathways. In the deciduous forests like BHFs, our results suggest ET is more energy-dependent during growing season (Spring and Summer) and early non-growing season (Autumn) while more temperature-dependent during winter season.

Domestic heating systems in the UK and across northern Europe are responsible for a substantial fraction of their countries’ carbon footprints. In the UK the vast majority of home space heating is via natural gas boilers with ’wet’ hydronic radiator systems. Most of those use TRVs (Thermostatic Radiator Valves) to avoid overheating, improve comfort and save energy. To meet Net Zero targets 20 million such UK gas systems may be retrofitted with heat pumps. Heat pump system designers and installers are cautious about retaining TRVs in such retrofitted systems in part because of worries that TRV temperature setbacks that lower heat demand may actually raise heat pump electricity demand in a "bad setback effect", thus wasting energy. This paper presents a new view of heat pump control and provides the first exploration of this issue, modelling one such industry claim, and finds that though real it should not apply to typical UK retrofits with weather compensation. The energy efficiency benefits of TRVs for older and partly-occupied homes, and to keep bedrooms cooler, remain valid. Comfort-seeking householders and installers should know that setting ’stiff’ temperature regulation may invoke the bad setback effect and cost dearly in energy and carbon footprint.

The plate heat exchanger (PHE) is a component that provides heat to be transferred from hot water to domestic cold water without mixing them with high efficiency. Over the lifetime of the PHE, cyclic pressures act on the brazing points and the plates, and this may lead to fatigue failure. The fatigue behaviour of the PHE, designed by using copper-brazed 316L stainless steel, was investigated in this study. First, the fatigue tests under the load ratio R = 0.1 were performed on the Vibrophore 100 testing machine to obtain the S-N curve of the analysed brazed joint. Based on the obtained experimental results, an appropriate material model of the analysed brazed joint has been created, which was validated with numerical calculation in the framework of a program code Ansys. A validated material model was then used for the subsequent numerical analysis of PHE. In order to carry out a numerical calculation using the finite element method (FEM), a 3D model of the heat exchanger was created based on the previous scanning of PHE-geometry. Thereafter, the geometry was parameterised, which allowed us to perform parametric simulations (monitoring different responses depending on the input geometry). Numerical simulations were carried out in the framework of the Ansys software, whereby the obtained results were analysed, and the responses were appropriately characterised according to previously determined load cases.

Wheat pollen, characterized by its short lifespan, exhibits rapid germination after anthesis. The preservation of wheat pollen is contingent upon environmental factors, including temperature, relative humidity, light, and wind. The objective is to develop a method for preserving wheat pollen effectively, specifically for the purpose of breeding. The short longevity of wheat pollen grains renders it impractical to conduct tests for pollen viability and in vitro germination on a large scale. Herein, the impact of storage temperatures and duration was assessed on pollen viability and in vitro germination to optimize storage conditions for preserving pollen viability. Pollen grains from 50 diverse spring wheat genotypes, each with three replicates, were harvested and stored at temperatures of 22°C, -20°C, and 4°C. Subsequently, pollen viability and in vitro germination rates were determined after storage of 1, 3, and 6 days. The results revealed that storage temperatures, durations, genotypes, and their interactions had a statistically significant impact on both pollen viability and in vitro germination. Notably, when pollen was kept at 22°C, almost all genotypes exhibited a loss of pollen viability and in vitro germination after 1, 3, and 6 days of storage. Likewise, storage at -20°C failed to extend pollen germination. However, at a storage temperature of 4°C, the pollen of 36 wheat genotypes exhibited a range of 6-14% in vitro pollen germination and remained viable even for 6 days. Simple linear regression analysis further revealed a significant negative correlation between pollen viability, in vitro germination, and storage time and temperature. In conclusion, our findings underscore 4°C as the optimal temperature for preserving pollen viability and in vitro pollen germination in spring wheat for up to 6 days. The results of the present study suggests that pollen viability of wheat is genotype de-pendent, storage temperature and storage duration. Thus, the 36 wheat genotypes identified during the present work could be efficiently maintained at 4◦C for short-term storage (6 days) and could be further used for genetics and breeding purposes.

This paper proposes a simulation technique for investigating the battery thermal management system based direct refrigerant cooling (BTMS-DRC). It employs finite element method for a combined-conduction-convection heat transfer to predict the module temperature and to prove the temperature uniformity. The refrigerant side cooling is based on the two-phase flow evaporation which is represented by the convection heat transfer (flow evaporation) under a certain refrigerant saturation temperature. The battery heat generation is modeled as the constant heat flux. The main module is modeled as the conduction heat transfer. The real BTMS-DRC is constructed for experimentation with the test bench which is based on the dual-evaporators vapour compression refrigeration system. The simulated result is validated with the experimental results to ensure the correction of the modelling. The simulation also investigates the impact of the heat generation, convection heat transfer coefficient, refrigerant saturation temperature, and thermal conductivity on the module temperature and temperature uniformity. It is found that the simulated results agree well with the experimental results. The errors are around 2.9 - 7.2% throughout the specified working conditions. Overall, the proposed technique can be used as a design tool for further developing the BTMS-DRC.

The effects of anisotropic properties (wettability and roughness) on microgroove surfaces in pool boiling heat transfer using Novec-7100 as a working fluid were experimentally investigated. The idea of introducing the concept of anisotropic wettability in boiling experiments draws inspiration from biphilic surfaces. The investigation is also motivated by two-phase immersion cooling, which involves phase-change heat transfer by using dielectric liquid as a working fluid. Very few studies have focused on the effects of surfaces with anisotropic properties on boiling performance. Thus, this study aims to examine the pool boiling heat transfer performance on surfaces with microgroove-induced anisotropic properties under the saturation condition. A femtosecond laser–texturing method was employed to create microgroove surfaces with different groove spacing. The results indicated that anisotropic properties affected the heat transfer coefficient and critical heat flux. Relative to the plain surface, microgroove surfaces enhanced the heat transfer performance due to the increased number of bubble nucleation sites and higher bubble detachment frequency. An analysis of bubble dynamics under different surface conditions was conducted with the assistance of high-speed images. The microgroove surface with groove spacing of 100 μm maximally increased the BHTC by 37% compared to the plain surface. Finally, the CHF results derived from experiments were compared with related empirical correlations. Good agreement was achieved between the results and the prediction correlation.

The article presents a hybrid method for calculating the chemical composition of steel with the required hardness after cooling from the austenitizing temperature. Artificial neural networks and genetic algorithms were used to develop the model. Based on 550 diagrams of continuous cooling transformation (CCT) of structural steels available in the literature, a dataset of experimental data was created. Artificial neural networks were used to develop a hardness model describing the relationship between the chemical composition of the steel, the austenitizing temperature, and the hardness of the steel after cooling. A genetic algorithm was used to identify the chemical composition of the steel with the required hardness. The value of the objective function was calculated using the neural network model. The developed method for identifying the chemical composition was implemented in a computer application. Examples of calculations of mass concentrations of steel elements with the required hardness after cooling from the austenitizing temperature are presented. The model proposed in this study can be a valuable tool to support chemical composition design by reducing the number of experiments and minimizing research costs.

In the face of climate change, bringing more useful alleles and genes from wild relatives of wheat is crucial to develop climate-resilience varieties. We used two populations of backcrossed recombinant inbred lines (BIL1 and BIL2), developed using two intra-specifically diverse Aegilops tauschii accessions from lineage 1 and lineage 2, respectively, and backcrossing to common wheat cultivar ‘Norin 61’. The study aimed to identify quantitative trait loci (QTL) associated with heat stress (HS) tolerance. The two BILs were evaluated under heat stress environments in Sudan for phenology, plant height (PH), grain yield (GY), biomass (BIO), harvest index (HI), and thousand kernel weight (TKW). Grain yield was significantly correlated with BIO and TKW under HS; therefore, stress tolerance index (STI) was calculated for these traits as well as for GY. A total of 16 heat tolerant lines were identified based on GY and STI-GY. The QTL analysis performed using inclusive composite interval mapping identified a total of 40 QTLs in BIL1 and 153 QTLs in BIL2 across all environments. We detected 39 QTLs associated with GY-STI, BIO-STI, and TKW-STI in both populations (14 in BIL1 and 25 in BIL2). The QTL associated with STI were detected on chromosomes 1A, 3A, 5A, 2B, 4B, and all the D-subgenomes. We found that QTL detected only under HS for GY on chromosome 5A, TKW on 3B and 5B, PH on 3B and 4B, and grain filling duration on 2B. The higher number of QTLs identified in BIL2 for heat stress tolerance suggests the importance of assessing the effects of intraspecific variation of Ae. tauschii in wheat breeding as it could modulate the heat stress responses/adaptation. Our study provides useful genetic resources for uncovering heat-tolerant QTLs for wheat improvement for heat stress environments.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

Finnish government's carbon neutrality goal by 2035 requires integration of renewable energy sources into the power grid. Considering the stochasticity of these resources, additional sources of flexibility are necessary to balance supply and demand in the power grid. District heating network (DHN) operators in Finland plan to shut down fossil-fuel-based combined heat and power plants and electrify heating systems by deploying heat pumps (HPs) and electric boilers. Techno-economic analysis and optimal operation of DHN-connected HPs and electric boilers in providing ancillary balancing services considering the 15-minute granularity in the balancing markets in Finland were investigated. The objective was to maximize the potential revenue for DHN operators gained from the day-ahead electricity market and frequency containment reserve (FCR) balancing markets. Three inter-connected DHNs in the Helsinki metropolitan area were optimized considering the reference year 2019 and each operator's decarbonization strategies for 2025. HPs could gain the highest profit from FCR-D up-regulation market, while the electric boiler may gain considerable profits from FCR-D down-regulation market. Compared to other balancing markets studied, the FCR-N market had a limited profit margin. Sensitivity analysis indicated that spot electricity prices and CO2 emission allowance prices have a significant impact on the profit from balancing markets.

Aircraft heat exchangers play a crucial role in maintaining thermal balance and ensuring that essential components operate efficiently and safely. In this context, it is highly relevant to gain knowledge about the deterioration and the predominant damage mechanisms of these components. In this study, two different non-destructive methods are employed to analyze the damage initiation of a heat exchanger part during fatigue test. On the one hand, Acoustic Emission technique is employed using membrane-free microphones capable of capturing a broad bandwidth. The acoustic events were classified by a machine learning algorithm to determine their source and damage mechanisms. On the other side, Digital Image Correlation (DIC) allowed the measurement of the strain evolution along the test and more precisely, redistributions were considered as damage indicators. As a result, it was identified that AE served as early damage indicator as the cumulative number of events was in good agreement with the severity of the damage. With respect to classification two clear clusters ascribed to different type of events were identified. In the case of DIC, strain redistributions gave clear indications of damage or deterioration but at a later stage compared to AE

Molybdenum tailings powder (MTs) is an industrial waste that contains more than 85% contents of SiO2, Al2O3, CaO, and Fe2O3. Therefore, MTs has the potential pozzolanic activity and can be used as a mineral admixture in cementitious materials. In order to understand the influence of MTs as an admixture on the cement hydration process, the hydration heat and hydration kinetics of the composite cementitious materials (CCMs) were investigated by an isothermal calorimeter and the Krstulovic-Dabic model. Furthermore, the influences of fly ash (FA), slag (SL) and MTs on hydration heat at the same content were compared and analyzed. Results show that proper amount of MTs can promote the hydration of CCMs. When the content of MTs is not more than 15%, the second exothermic peak of CCMs appears earlier and the peak heat release increases. However, when the content of MTs exceeds 15%, the second exothermic peak of CCMs is delayed and the peak heat release decreases. The cumulative heat release of CCMs gradually decreases with an increasing content of MTs. When the replacement of MTs, FA, and SL is 15% respectively, the addition of MTs enhances the second exothermic peak of CCMs compared to FA and SL. The final heat release of MTs is higher than that of FA, but lower than that of SL. The hydration process of CCMs undergoes three stages: nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The incorporation of MTs shortens the NG stage and I stage.

Due to an urgent need for reducing the fast progressing climate changes, a rapid, standardized and replicable solution for the infrastructure restructuring of heat demand coverage of buildings at district and city level must be developed. As more and more communities in Europe, especially in Germany, are obligated to have plans for coverage of heat demand, city planners, energy agencies seek a tool, which will help them to design the first drafts of heating network routes, which can supply whole districts and cities with renewable energy. ArcGIS Pro Tools like Least-Cost-Path-Analysis (LCPA) and Closest Facility (CF) allow to find the shortest and “cheapest” way between the heat source and heat consumers in the analyzed areas. Starting from the community level, through the district, county, voivodeship and whole country levels, the replication of the methods for generating district heating (DH) network infrastructure can be achieved. The proposed LCPA and CF based methods help to design the most suitable and efficient DH networks in the analyzed areas. As only few open-source data input, like street networks and building footprints are needed, the methods can be implemented in all communities of the country of Poland. In this paper one example of one community of Wroclaw county, called Siechnice and surroundings is presented.

The feasibility of recovering bioactive antioxidants from Phyllantus emblica leaves using ethanol -water mixture (0 – 100%) and heat-assisted extraction technology (HAE-T) was investigated in this present study. To this effect, the process parameter of operating temperature (OT: 30 -50 oC), solid -to-liquid ratio (S:L: 1:20 - 1:60 g/mL) and extraction time (ET: 45 - 180 min) were investigated on the extract total phenolic content (TPC, mg GAE/g d.w), yield (EY, %) and antioxidant activity (μM AAE/g d.w) by employing the Box-Behnken experimental design (BBD) available in response surface methodology (RSM). Multi-objective process optimization using the desirability function algorithm to determine set of process variables that simultaneously optimize process responses of TPC, EY and AA was also investigated. The recovery process was thereafter modeled with BBD-RSM and multi gene genetic programming (MGGP) algorithm and model reliability assessment via Monte Carlo simulation were conducted for the best performing set of models for predicting TPC, EY and AA values. The HPLC characterization of the recovered extract was carried out to ascertain the phenolic compound constituents of the Phyllantus emblica leaf extract. The 50% ethanol solution was found to be the best for the optimal extraction of antioxidants from Phyllantus emblica leaves. The HAE-T was suitable for recovering bioactive extract from Phyllantus emblica leaves and investigated process parameters have impacts on the recovery process. The process parameters that simultaneously gave the optimum EY of 21.6565%, TPC of 67.116 mg GAE/g and AA of 3.68583 µM AAE/g were OT of 41.61 oC, S:L of 1:60 g/mL and ET of 180 min. The HPLC extract profiling revealed that the bioactive constituents present in the recovered extract were betulinic acid, gallic acid, chlorogenic acid, caffeic acid, ellagic acid, and ferulic acid. Both the developed BBD-RSM and evolved MGGP-based models predicted the observed process response of TPC, EY and AA satisfactorily with BBD-RSM models marginally better in their predictions. The reliability results showed that the BBD-RSM models predicted TPC, EY and AA values with high certainty of 99.985%, 97.569% and 98.661%, respectively.

The fusion of surface-modified steel with tungsten carbide (WC) and NiCrBSi powder through laser metal deposition has emerged as a formidable strategy for fortifying components against wear and corrosion in extreme operating environments. Meticulous selection of WC content, innovative pre-alloying techniques, and precise control of laser metal deposition profoundly influence the mechanical properties and microstructural evolution of WC-NiCrBSi coatings applied to surface-enriched commercial alloy steel (805M2, 832M13, and 827M40). These tailored coatings exhibit exceptional resilience, ideal for harsh industrial settings in Oil and gas drilling, petrochemical, and Mining sectors. Advanced materials testing techniques, including scanning electron microscopy, light optical microscopies, and microhardness testing, unveil the innate hardness attributes, with findings highlighting the unassailable fortitude of the Mixed matrix layer's side face. The amalgamation of these testing methodologies with laser metal deposition promises an unparalleled path to extend the operational lifespan of critical components in challenging working conditions. The research horizon for WC-NiCrBSi coatings remains broad, with the potential to enhance durability, operational efficiency, and cost-effectiveness across diverse applications.

The HSP70 and HSP90 family members belong to molecular chaperones that exhibit protective functions during the cellular response to stressful agents. We investigated whether the exposure of rats to chronic mild stress (CMS), a validated model of depression, affects the expression of HSP70 and HSP90 in the prefrontal cortex (PFC), hippocampus (HIP) and thalamus (Thal). Male Wistar rats were exposed to CMS for 3 or 8 weeks. The antidepressant imipramine (IMI, 10 mg/kg, i.p., daily) was introduced in the last five weeks of the long-term CMS procedure. Depressive-like behavior was verified by the sucrose consumption test. The expression of mRNA and protein was quantified by real-time PCR and Western blot, respectively. In the 8-week CMS model, stress alone elevated HSP72 and HSP90B mRNA expression in the HIP. HSP72 mRNA was increased in the PFC and HIP of rats not responding to IMI treatment vs. IMI responders. The CMS exposure increased HSP72 protein expression in the cytosolic fraction of the PFC and HIP, and this effect was diminished by IMI treatment. Our results suggest that elevated levels of HSP72 may serve as an important indicator of neuronal stress reactions accompanying depression pathology and could be a potential target for antidepressant strategy.

Aluminium bronzes possess a unique combination of high strength and wear and corrosion resistance in aggressive environments; thus, these alloys find wide application in marine, shipbuilding, aviation, railway, offshore platform applications and other fields. Iron-aluminium bronzes (IABs) are the cheapest and most widely used. When the aluminium content is above 9.4 wt%, IAB is biphasic (i.e. it undergoes -transformation) and can be subjected to all heat-treatment types depending on the desired operating behaviour of the bronze component. This article presents correlations (mathematical models) between the primary mechanical characteristics (yield limit, tensile strength, elongation, hardness and impact toughness) and the ageing temperature and time of quench at 920°C in water Cu-11Al-6Fe bronze, obtained using the centrifugal casting method. The microstructure evolution was evaluated depending on the ageing temperature and time changes. Overall, the research was conducted in three successive inter-related stages: a one-factor-at-a-time study, planned experiment, and optimisations. Four optimisation tasks, which have the greatest importance for practice, were formulated and solved. The defined multiobjective optimisation tasks were solved by searching for the Pareto-optimal solution approach. The decisions were made through a nondominated sorting genetic algorithm (NSGA-II) using QstatLab. The optimisation results were verified experimentally. Additional samples were made for this purpose, quenched at 920°C in water and subjected to subsequent ageing with the optimal values of the governing factors (ageing temperature and time) for the corresponding optimisation task. The comparison of the results for the mechanical characteristics with the theoretical optimisation results presents good agreement.

Wetlands, which is composed of soil, vegetation and water, has sufficient water supply and is sensitive to climate change. This study analyzed the coupling degree between wetlands and atmosphere, and discussed the influence of environmental factors (solar radiation and water vapor pressure deficit) on latent heat flux by using the experimental data from the Maduo Observatory of Climate and Environment of the Northwest Institute of Eco-Environment and Resource, CAS and WRF model. The results showed, during the vegetation growthing season, the average value of Ω (decoupling factor) is 0.38 in alpine wetlands, indicating the coupling between wetlands and atmosphere is poor; Solar radiation is the main factor influencing the latent heat flux in the results of both observation data analysis and model simulation, and solar radiation and water vapor pressure deficit still have an opposite reaction to latent heat flux; when solar radiation and water vapor pressure deficit increase by 30%, the average daily amount of latent heat flux increases from 5.57 MJ·m-2 to 7.50 MJ·m-2 and decreases to 5.17 MJ·m-2, respectively. This study provides a new research approach for the study of the parameterization of latent heat flux and evapotranspiration under the context of global climate change.

Due to the complexity of the microstructure of porous media, it is of great significance to explore the heat transport mechanism in porous media in many engineering applications. In this study, an expression for effective thermal conductivity（ETC） of porous media with randomly distributed damaged tree-like bifurcation networks is derived based on the theory of thermodynamics and fractal features of tree-like bifurcation networks. We investigate the effect of heat conduction and heat convection in porous media with randomly distributed damaged tree-like bifurcation networks on the ETC of the porous media. It is found that our fractal model is in good consistency with the existing available experimental data. In addition, the influence of the micro-structural parameters of the model on heat transfer in the porous media have been analyzed in detail. The research results can provide significant theoretical guidance for the development and design of heat transfer systems.

Geothermal energy is likely to be a significant contributor in achieving sustainable energy goals and net-zero emissions targets. Within geothermal power plants, heat exchangers play a critical role in harnessing this renewable energy source. However, these heat exchangers encounter significant challenges when exposed to geothermal fluids, including erosion, corrosion, and scaling, which adversely affects their performance and longevity. The current review focuses on surface engineering techniques, particularly coatings, as a highly effective and economically viable solution to address these challenges in geothermal heat exchangers. The review begins by providing an overview of geothermal energy, its significance in the context of sustainability and the important role played by heat exchangers in geothermal power generation, followed by the challenges and their impact on heat exchangers. The subsequent section focuses on surface engineering by coatings and its types employed to enhance the performance of heat exchangers. In the final part, the reader is presented with an overview of the challenges associated with the application of coatings in geothermal heat exchangers and potential future directions in this field. This review offers a detailed understanding of the critical role coatings play in improving the efficiency and service life of heat exchangers in geothermal power plants.

In Geo Polymer bricks (GPB), fly ash content which is a waste from power plants is converted into bricks by chemical treatment. GPB can be dried by using appropriate curing methods. Conven-tionally electric oven curing is one of the prominent methods. Using solar dryer instead of elec-trical oven gives added advantage of saving high grade electrical energy. So in this work solar dryer with PCM (Phase Change materials) Paraffin Wax and without PCM is used for curing ap-plication. GPB are gaining added advantage when compared to conventional bricks like cement and sand bricks in terms of strength. GPB has been taken as specimen for comparing the com-pressive, tensile split strength and flexural strength by electrical energy based curing and solar energy based curing. It is experimentally observed that solar energy based curing with PCM and without PCM exhibits higher compressive strength, higher tensile split strength and flexural strength when compared to electrical energy based curing. Solar curing with PCM shows higher compressive strength, higher tensile split strength and flexural strength when compared to Solar curing without PCM. Open solar curing is a traditional technique but nowadays aggressive cli-matic conditions can lead to severe damage of Geo polymers. The novelty of this work is to suggest to study the effect of PCM like paraffin wax in solar drying on curing time, mechanical properties of GPB.

Since the photocatalytic reaction is a surface reaction, enhancing the gas movement around photocatalyst would promote photocatalytic CO₂ reduction performance. A new approach to enhance the gas movement around the photocatalyst by the natural thermosiphon movement of gasses around photocatalyst using black body material was proposed and confirmed experimentally, but the heat transfer mechanism on the phenomena was not clarified yet. The purpose of this study is to clarify the heat transfer mechanism of it. This study calculated the temperature of mixed gases of CO₂ and NH₃ around P₄O₁₀/TiO₂ photocatalyst by the heat transfer formula. It is revealed that there was no difference between the increase temperature (T_g) from the temperature at the beginning of the CO₂ reduction experiment (T_ini) and the temperature of mixed gases of CO₂ and NH₃ measured by thermocouple in the experiment (T_e) under the illumination condition with a visible light (VIS) + an infrared light (IR) and IR only. The heat transfer model proposed by this study has predicted T_g well under the illumination condition with VIS + IR and IR only well. On the other hand, it is revealed that the difference between T_g and T_e was as large as 10 ℃ under the illumination condition with an ultra violet light (UV) + VIS + IR.

The aim of this study was to investigate the effect of laser irradiation to computer-aided de-sign/computer-aided fabrication (CAD/CAM) resin blocks coated with a silane coupling agent on the bond strength between the resin blocks and composite resin. The CAD/CAM resin blocks used in this study were Cerasmart 300 (GC) and Vita Enamic (Vita); they were cut into plates and then subjected to a series of treatments. After processing with a silane coupling agent, treatment with a semiconductor laser was performed at 3.0, 5.0, and 7.0 W, followed by the bonding procedures. The control group included those exposed to silane and bonded without laser application. After bonding, a mold with a simulated cavity was formed on the specimen and filled with flowable composite resin, and they were stored for 24 h or stressed by thermal cycling for subsequent testing that assessed the shear bond strength (n = 10). The results revealed that the bond strength was significantly enhanced by laser irradiation after applying a silane coupling agent, whereas significant effect was not detected between the materials. Particularly, 7 W laser irradiation had a significant effect on the bond strength between the composite resin and Cerasmart block after thermal cycling.

Heat shock factor 1 (HSF1) is a transcription factor crucial for regulating heat shock response (HSR), one of the significant cellular protective mechanisms. When cells are exposed to proteotoxic stress, HSF1 induces the expression of heat shock proteins (HSPs) to act as chaperones, correcting the protein-folding process and maintaining proteostasis. In addition to its role in HSR, HSF1 is overexpressed in multiple cancer cells, where its activation promotes malignancy and leads to poor prognosis. The mechanisms of HSF1-induced tumorigenesis are complex and involve diverse signaling pathways, dependent on cancer type. With its important roles in tumorigenesis and tumor progression, targeting HSF1 offers a novel cancer treatment strategy. In this article, we examine the basic function of HSF1 and its regulatory mechanisms, focus on the mechanisms involved in HSF1’s roles in different cancer types, and examine current HSF1 inhibitors as novel therapeutics to treat cancers.

Statistical analysis of mechanical properties of thin-walled samples (~500 microns) obtained by selective laser melting from AlSi10Mg material and subjected to heat treatment for 1 hour at temperatures from 260 °C to 440 °C (step of aging temperature change 30 °C) has shown that the maximum strain hardening in the stretching diagram section from yield strength to tensile strength is achieved at the heat treatment temperature equal to 290 °C. At carrying out of correlation analysis statistically significant positive correlation between deformation corresponding to yield strength and the sum of heights of the largest protrusions and depths of the largest depressions of the surface roughness profile within the basic length of the sample (Rz) and the full height of the surface roughness profile (Rmax) was established. It was found that the reason for the correlation is the presence of cohesive states between the extreme values of the surface roughness profile that persist along the entire length of the specimen.

The Mahuagou gold deposit is among the most important gold deposits in the core of Huangling Anticline. However, the geochemical exploration on the surface of the mining area presents challenges due to the thin overburde.This paper focuses on the overburden soil of Fengxiangshugou (FXS) – Mahuanggou (MHG) section as the research object, utilizes chemical form analysis of gold, soil halogen survey, and heat-released mercury survey to determine the key deep-penetrating geochemical methods for mining area. The results indicated that Si and Al components of samples exhibit minimal variation, suggesting that drift loads did not influence the overburden soil. Based on the systematic clustering, As, Sb, Mo, Bi, W and Hg emerge as ore-body or ore-belt front elements of hydrothermal gold deposits. In the study area, the predominant chemical form of gold in soil is the strong organic bond. Compared to the total amount, strong organic bound gold and heat-released mercury show higher anomaly contrasts, making them crucial indicators of faults, intrusions and hidden ore bodies. Consequently, chemical form analysis of gold and heat-released mercury surveys can enhance the anomaly contrast, proving beneficial for geochemical prospecting for weak anomalies in this area.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

Pool boiling is extensively utilized in various fields, such as electronics cooling, battery cooling, nuclear power plants, and chemical processing. In the process of temperature control through boiling, the generation and transportation of bubbles play a crucial role in calculating the heat transfer capacity of the system. Therefore, it holds immense significance to gain a profound understanding of the mechanisms underlying bubble formation, growth, and detachment. Currently, numerous mechanistic explanations and empirical correlations have been proposed to elucidate various parameters of bubbles during the boiling process. These findings were considered valuable references in selecting appropriate boiling media and designing efficient heating surfaces. To comprehensively present the progress of bubble formation and heat transfer during the boiling process, the forces exerted on the bubbles was highlighted in this article. And a meticulous review on bubble force analysis and correlation formulas pertaining to various relevant parameters (e.g. nucleation sites density, bubble growth rate, detachment diameter, detachment frequency) were conducted. This review article also were expected to provide a novel foundation for further exploration of enhanced boiling heat transfer.

We study the work fluctuations in ergotropic heat engines, namely two-strokes quantum Otto engines where the work stroke is designed to extract the ergotropy (the maximum amount of work by a cyclic unitary evolution) from a couple of quantum systems at canonical equilibrium at two different temperatures, whereas the heat stroke thermalizes back the systems to their respective reservoirs. We provide an exaustive study for the case of two qutrits whose energy levels are equally spaced at two different frequencies by deriving the complete work statistics. By varying the values of temperatures and frequencies, only three kinds of optimal unitary strokes are found: the swap operator U1, an idle swap U2 (where one of the qutrits is regarded as an effective qubit), and a non trivial permutation of energy eigenstates U3, which indeed corresponds to the composition of the two previous unitaries, namely U3 = U2U1. While U1 and U2 are Hermitian (and hence involutions), U3 is not. This point has an impact on the thermodynamic uncertainty relations (TURs) which bound the signal-to-noise ratio of the extracted work in terms of the entropy production. In fact, we show that all TURs derived from a strong detailed fluctuation theorem are violated by the transformation U3.