Plasma being the fourth and most abundant form of matter extensively exists in the universe in the inter-galactic regions. It provides an electrically neutral medium of unbound negative and positive charged particles, which has been produced by subjecting air and various other gaseous mixtures to strengthen the electromagnetic field and by heating compressed air or inert gasses for creating negative and positive charged particles known as ions. Nowadays, many researchers are paying attention to the formation of artificial Plasma and its potential benefits for mankind. The literature is sparsely populated with the applications of Plasma. This paper presents specific methods of generation and applications of Plasma, which benefits humankind in various fields, such as in electrical, mechanical, chemical and medical fields. These applications include hydrogen production from alcohol, copper bonding, semiconductor processing, surface treatment, Plasma polymerization, coating, Plasma display panels, antenna beam forming, nanotechnology, Plasma Torch, Plasma pencils, low-current non-thermal Plasmatron, treatment of prostate cancer, Plasma source ion implantation, cutting by Plasma, Plasma etching, pollution control, neutralization of liquid radioactive waste, etc. Resultantly, worth of Plasma technology in the medical industry is increasing exponentially that is closing the gap between its benefits and cost of equipment used for generating and controlling it.

Structure from Motion with Multi-View Stereo photogrammetry (SfM) is increasingly utilised in geoscience investigations as a cost-effective method of acquiring high resolution (sub-meter) topographic data, but has not been thoroughly tested in gullied savanna systems. The aim of this study was to test the accuracy of topographic models derived from aerial (via an Unmanned Aerial Vehicle, ‘UAV’) and ground-based (via a handheld digital camera, ‘Ground’) SfM in modelling a hillslope gully system in dry-tropical savanna, and to assess the strengths and limitations of the approach at different scales. A UAV survey covered an entire hillslope gully system (0.715 km²), whereas a Ground survey covered a single gully within the broader system (650 m²). SfM topographic models, including Digital Surface Models (DSM) and dense point clouds, were compared against RTK-GPS point data and a pre-existing airborne LiDAR Digital Elevation Model (DEM). Results indicate UAV SfM can deliver topographic models with a resolution and accuracy suitable to define gully systems at a hillslope scale (e.g., 0.1 m resolution with ~ 0.5 – 1.3 m elevation error), while ground-based SfM is more capable of quantifying gully morphology (e.g., 0.01 m resolution with ~ 0.1 m elevation error). Key strengths of SfM for these applications include: the production of high resolution 3D topographic models and ortho-photo mosaics, low survey instrument costs (< $AUD 3,000); and rapid survey time (4 and 2 hours for UAV and Ground survey respectively). Current limitations of SfM include: difficulties in reconstructing vegetated surfaces; uncertainty as to optimal survey and processing designs; and high computational demands. Overall, this study has demonstrated great potential for SfM to be used as a cost-effective tool to aid in the mapping, modelling and management of hillslope gully systems at different scales, in tropical savanna landscapes and elsewhere.

Hybrid machine tools combining additive and subtractive processes have arisen as a solution to the increasing manufacture requirements, boosting the potentials of both technologies, while compensating and minimizing their limitations. Nevertheless, the idea of hybrid machines is relatively new and there is a notable lack of knowledge in the field. Therefore, in the present paper, an insight into the advancements of hybrid machines is given, identifying their real capabilities, together with the latest developments from an industrial context. In addition, the current situation and future perspectives of hybrid machines from the point of view of process planning, monitoring and inspection are discussed. Finally, the challenges that must be overcome and the opportunities that the hybrid machines will provide in the forthcoming years are presented.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

Polylactic Acid (PLA) is an organic polymer commonly used in fused deposition (FDM) printing and biomedical scaffolding that is biocompatible and immunologically inert. However, variations in source material quality and chemistry make it necessary to characterize the filament and determine potential changes in chemistry occurring as a result of the FDM process. We used several spectroscopic techniques, including laser confocal microscopy, Fourier-Transform Infrared (FTIR) spectroscopy and photoacousitc FTIR spectroscopy, Raman spectroscopy, and X-ray photoelectron Spectroscopy (XPS) in order to characterize both the bulk and surface chemistry of the source material and printed samples. Scanning Electron Microscopy (SEM) and Differential Scanning Calorimetry (DSC) were used to characterize morphology, crystallinity, and the glass transition temperature following printing. Analysis revealed calcium carbonate-based additives which were reacted with organic ligands and potentially trace metal impurities, both before and following printing. These additives became concentrated in voids in the printed structure. This finding is important for biomedical applications as carbonate will impact subsequent cell growth on printed tissue scaffolds. Results of chemical analysis also provided evidence of the hygroscopic nature of the source material and oxidation of the printed surface, and SEM imaging revealed micro and sub-micron scale roughness that will also impact potential applications.

A simple and effective surface modification of polyester fabrics with sulfuric acid to improve the interfacial deposition of polypyrrole was presented in our work. A range of sulfuric acid concentrations were analyzed by studying water contact angle. Effect of sulfuric acid modification on the deposition of polypyrrole was investigated by sheet resistance and color depth of fabric samples. Polyester fabrics coated with polypyrrole layer were confirmed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-Ray diffraction spectra (XRD), Fourier transform infrared spectroscopy (FTIR). XPS showed that sulphur containing functional groups were obviously appeared on the polyester fiber surface after modification, which were advantageous to promote the deposition of polypyrrole onto polyester fabrics. The improved deposition increased electrical conductivity of fabric samples.

Interfaces between layers in 3D-printed elements produced by extrusion-based material deposition were investigated on both macro- and micro-scales. On the macro-scale, compression and bend tests were performed on two 3D-printable cement-based compositions (3PCs), namely C1 and C2. The influences of binder composition and time interval between layers on layer-interface strength were critically analyzed. In the context of additive manufacturing, the optimized composition C2, containing pozzolanic additives, exhibited mechanical performance superior to that of the mixture with Portland cement as the sole binder. In particular, Mixture C2 showed a less pronounced decrease in interface tensile strength. Even for time intervals between depositions of two layers as long as 1 day the loss in corresponding flexural strength was below 25%, as compared with C2 specimens tested in the perpendicular direction. In contrast, the decrease in flexural strength measured for C1 specimens amounted to over 90% for the same set of parameters. Higher porosity at the interfaces of the printed concrete layers was identified as the cause for the lower interface strengths of C1. Microscopic observations supported the findings of the macroscopic investigations. While a pronounced recovery (“self-healing”) of the porous, discontinuous interlayers was observed with increasing age for Mixture C2, in case of C1 the filling products grown in the porous interlayer were found to be non-strengthening.

The current paper is studying the influence of geometrical parameters of the FDM (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose, i.e. PLA (polylactic acid). The study was conducted using a set of different nozzles (0.4, 0.6 and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. To explain the results obtained, a mesostructure evaluation through SEM scans of the samples were used. A significant influence of geometric process parameters was detected on sample mesostructure and, consequently, on sample strength.

Hot stamping dies include cooling channels to treat the formed sheet. The optimum cooling channels of dies & molds should adapt to the shape and surface of the dies, so that a homogeneous temperature distribution and cooling are guaranteed. Nevertheless, cooling ducts are conventionally manufactured by deep drilling, attaining straight channels unable to follow the geometry of the tool. Laser Metal Deposition (LMD) is an additive manufacturing technique capable to fabricate nearly free-form integrated cooling channels and therefore shape the so-called conformal cooling. The present work investigates the design and manufacturing of conformal cooling ducts, which are additively built up on hot work steel and then milled in order to attain the final part. Their mechanical performance and heat transfer capability has been evaluated, both experimentally and by means of thermal simulation. Finally, conformal cooling conduits are evaluated and compared to traditional straight channels. The results show that LMD is a proper technology for the generation of cooling ducts, opening the possibility to produce new geometries on dies & molds and, therefore, new products.

Special preparation of SBA-15 materials has been carried out for creating adsorbents exhibiting an enhanced and selective adsorption toward CO2. This creation starts from an adequate conditioning of the silica surface, via a thermo-alkaline treatment to increase the population of silanol species on it. CO2 adsorption is only reasonably achieved when the SiO2 surface becomes aminated after put in contact with a solution of an amino alkoxide compound in the right solvent. Unfunctionalized and amine-functionalized substrates were characterized through X-ray diffraction, N2 sorption, Raman spectroscopy, electron microscopy, 29Si solid-state NMR, and NH3 thermal programmed desorption. These analyses proved that the thermo-alkaline procedure desilicates the substrate and eliminates the micropores (without affecting the SBA-15 capillaries), present in the original solid. NMR analysis confirms that the hydroxylated solid anchors more amino functionalizing molecules than the unhydroxylated material. The SBA-15 sample subjected to hydroxylation and amino- functionalization displays a high enthalpy of interaction, a reason why this solid is suitable for a strong deposition of CO2 but with the possibility of observing a low-pressure hysteresis phenomenon. Contrastingly, CH4 adsorption on amino-functionalized, hydroxylated SBA-15 substrates becomes almost 5 times lesser than the CO2 one, thus giving proof of their selectivity toward CO2.

We report the growth of graphene at a low temperature using the cold wall chemical vapor deposition technique (CWCVD). Few layered (~6-8 layers) graphene were grown on nickel-coated silicon with acetylene as the precursor gas. The advantage of the combination of the acetylene (as a carbon feedstock) and the nickel catalyst was the lowering of the graphene growth temperature. Nickel coated silicon samples were pre-treated (heat treatment in inert atmosphere) before the growth and the effect of the pre-treatment on the catalyst as well as on the grown film was studied. The final samples were characterized with scanning electron microscopy and Raman spectroscopy. In CWCVD route, the heating of only the substrate holder enabled high heating and cooling rates, which, along with the control over partial pressure of the precursor gas had profound effect on the formation of graphene. In the best sample we have achieved almost equal intensity of the G and 2D peaks in Raman spectrum, which implied about ~6-8 layers of Graphene. The defect peak (the D band) was extremely small in the sample and it was attributed to the ripples and the underlying roughness of the nickel film. We analyzed that a proper choice of the thickness of catalyst layer and a higher cooling rate after graphene growth it would be possible to obtain monolayered graphene. Similar samples grown in a normal atmospheric CVD (with some engineered design to promote fast cooling) were also compared with the cold wall CVD grown samples and plasma assisted CWCVD, and cold-wall CVD demonstrated a better control over the quality of graphene film through the fast cooling and a controlled partial pressure of the precursor gas.

The possibility of using additive manufacturing (AM) in the medicine area has created a new opportunities in health care. This has contributed to a sharp increase in demand for 3D printers, their systems and materials that are adapted to strict medical requirements. We described herein a medical-grade thermoplastic polyurethane (S-TPU), which was developed and then formed into a filament for Fused Deposition Modeling (FDM) 3D printers during a melt-extrusion process. S-TPU consisting of aliphatic hexamethylene 1,6-diisocyanate (HDI), amorphous α,ω-dihydroxy(ethylene-butylene adipate) (PEBA) and 1,4 butandiol (BDO) as a chain extender, was synthesized without the use of a catalyst. The filament properties were characterized by rheological, mechanical, physico-chemical and in vitro biological properties. The tests showed biocompatibility of the obtained filament as well as revealed no significant effect of the filament formation process on its properties. This study may contribute to expanding the range of medical-grade flexible filaments for standard low-budget FDM printers.

A review of the surface ablation of hominin teeth by attrition, abrasion and erosive wear. The occurrence of these lesions is explored in a sample of South African fossil australopithecine dentitions revealing excessive wear. Interpretation of the nature of the dietary components causing such wear in the absence of carious erosion provides insight into the ecology of the Plio-pleistocene epoch (1-2 million years ago). Fossil teeth inform much of the living past by their retained evidence after death. Tooth wear is the ultimate forensic evidence of lives lived.

Titanium dioxide (TiO2) and aluminum oxide (Al2O3) coatings have been investigated in a wide range of bio-applications due to their biodegradation and biocompatibility properties, that are key parameters for their use in the food packaging and biomedical devices fields. The present study evaluates and compares the electrochemical behavior of the non-coated, commercial resin-coated, TiO2-coated and Al2O3-coated aluminum in commercial beer electrolyte. For this, TiO2 and Al2O3 thin films were deposited on aluminum (Al) substrates using atomic layer deposition (ALD). The evaluation of the corrosion barrier layer properties was performed by linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). In addition, profilometry, grazing incidence X-ray diffractometry (GIXRD), scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR) analyses were performed to investigate the physical and chemical properties of the pristine and / or corroded samples. TiO2 and Al2O3 films presented an amorphous structure, a morphology that follows Al substrate surface, and a thickness of around 100 nm. Analysis of LSV data showed that ALD coatings promoted a considerable increase in corrosion barrier efficiency being 86.3% for TiO2-coated Al and 80% for Al2O3-coated Al in comparison with 7.1% of commercial resin-coated Al. This is mainly due to the lower electrochemical porosity, 11.4% for TiO2-coated Al and 20.4% for Al2O3-coated Al in comparison with 96% of the resin-coated Al, i.e. an increase of up to twofold in the protection of Al when coated with TiO2 compared to Al2O3 coated. The EIS results allow us to complement the discussions about the reduced corrosion barrier efficiency of the Al2O3 film for beer electrolyte once SEM and FT-IR analyzes did not show drastic changes in both investigated ALD films after the corrosion assays. The above results indicate that ALD TiO2 and Al2O3 films may be a viable alternative to replace the synthetic resin coatings frequently used in aluminum cans of use in the food industry.

The accumulation of high levels of lead or lead ions in a human body is harmful, particularly to children. Its neurotoxic effect is profound, damaging the central and peripheral nervous systems, resulting in stunted growth, behavioral problems and learning disabilities. The major source of lead or lead ions comes from the drinking water and tap water. The assessment of the water quality, including lead or lead ion content, is usually completed by a regional water department professional. This assessment is time-consuming and requires expensive instruments and skilled operators. Therefore, there is a need to produce a simple-use and relatively inexpensive method to detect lead or lead ions in water samples. This research has developed a simple-use, cost effective sensor system for the detection of lead ions in tap water. An under-potential deposited bismuth sub-layer on a thin gold film based electrochemical sensor was designed, manufactured and evaluated. Differential pulse voltammetry (DPV) measurement technique was employed in this detection. Tap water from the Cleveland, Ohio, USA regional water district was the test medium. Concentrations of lead ion in the range of 8 X 10^-8 M to 8 x 10^-4 M were evaluated. This DPV detection system required 3 -6 minutes to complete the detection measurement. A longer measurement time of 6 minutes was used for the lower lead ion concentration. The selectivity of this lead ion sensor was very good, and Fe III, Cu II, Ni II and Mg II at a concentration level of 5×10^-4 M did not interfere with the lead ion measurement.

The type of tail of sheep is an important economic trait. However, the candidate genes associated with the tail type are uncertain. The objective of this study was to identify the genetic region and genotype responsible for the tail type phenotype. Here we perform a genome-wide association study (GWAS) in 40 large tailed Han sheep and 40 Altay sheep as case and 40 Tibetan sheep as control. The results indicated that a total 31 genome-wide significant SNPs associated with type of tail traits were detected. For significant SNPS loci, determine its physical location, and screening of candidate genes within section. By combining information of previously reported and annotated biological functional genes, we identified SPAG17, Tbx15, VRTN, NPC2, BMP2 and PDGFD as the most promising candidate genes for type of tail traits. Based on the above identified candidate genes on type of tail traits, we selected BMP2 and PDGFD to conduct the genetic effect analysis in a large Altay sheep and Tibetan sheep population. Rs119 T>C in the exon1 of BMP2 gene and 1 SNPs in the exon4 (rs69 C>A) of PDGFD gene were detected, rs119 that located on exon1 of BMP2 gene was TT genotype in Altay sheep, while with CC genotype in Tibetan sheep. On rs69 of PDGFD gene, Altay sheep with CC genotype, however, Tibetan sheep with AA genotype. These results indicated that the significant associations of SNPs detected in GWAS were indirectly caused by the genetic effects of BMP2 and PDGFD on sheep tail fat deposition.

This manuscript introduces prospective hard engineering solutions to continuous episodic erosional events on beaches utilized for recreation and tourism. The basis of this paper is information from a modeling study completed in 2011 on a two mile stretch of beach in South Carolina. The study utilized three alternative groin systems and a no groin option. The optimum spacing of the groin applications and the retention rate of a replenished beach at the location was determined based on running a computer model (Genesis) for the environmental conditions (wave climate, littoral transport, etc.) at the demonstration site. It was also determined that the innovative groin alternative presented in this paper would likely develop as the most effective cost/benefit relationship among the more conventional alternatives utilized in the United States. The experimental groin system (modular adjustable permeable groin(s) MAPG) was calculated to save initial construction costs by 25% to 30%as compared to the other alternatives. This was significant when considering that adjacent beach impacts are minimized and the beach berm is better protected over the typical beach re-nourishment cycle. This paper attempts to facilitate further discussion of regional sediment budget and (coastal zone) management by bridging the divide between choosing only sand nourishment vs. engineered structures. We demonstrate that reintroducing engineered structures in combination with beach nourishment can be a cost effective solution to episodic erosional events over time while allowing longshore sediment transport.

Thin films (100-400 nm) of Ba_xSr_1-xTiO₃ (0≤x≤1) deposited in RF-magnetron co-sputtering equipment are presented in this research work. The change of deposition rate, gap energy, and resistivity as a function of temperature- applied power change in the growth parameters was studied through the ISO colour-code lines constructed with MATLAB: By analysing the trend information and take into account the influence of the calculated "x" parameter with the Boltzmann profile fitting is proposed a method to allow a controlled set up of the RF-magnetron co-sputtering system and predict the E_g and resistivity values in the Ba_xSr_1-xTiO₃ solid solution with 0≤x≤1 for amorphous and crystalline phases. Also, a versatile tool to optimise the deposition process and material properties.

The accurate assessment and monitoring of soil erosion is of great significance for guiding food production and ensuring ecological security, and it is a current research hotspot. In this paper, remote sensing and geographic information systems (GISs) are combined with the Revised Universal Soil Loss Equation (RUSLE model) to carry out research on soil erosion monitoring and make a quantitative evaluation. According to five factors, including rainfall erosivity, soil erodibility, topography, vegetation cover, crop management and water and soil conservation measures, the distribution of the soil erosion rate in Jilin Province in 2019 was mapped, and the soil erosion rate was divided into 5 levels according to the degree of erosion, including very slight, slight, moderate, severe and extremely severe erosion. Based on the segmented S-slope factor model and the unique topographical features of the study area, the relationships among the soil erosion rate, erosion risk level, erosion area, erosion amount and slope angle (θ) were systematically analysed, and a slope angle of 15° was identified as the threshold for soil erosion on sloped farmland in Jilin Province. The total soil erosion in Jilin Province was 402.14×106 t in 2019, the average soil erosion rate was 21.6 t·ha-1·a-1, and the average soil loss thickness was 1.6 mm·a-1; these values were far greater than the soil erosion rate risk threshold of 10 t ·Ha-1·a-1. Thus, the province has a strong level of soil erosion. We conclude that soil degradation is accelerating, and food production and the ecological environment will face severe challenges. It is suggested that soil erosion control should be carried out according to different types and slopes of land, with an emphasis on the management of forestland and farmland because forestland and farmland are currently the first types of land to be managed in Jilin Province. This paper aims to explore a timely, fast, efficient and convenient soil erosion monitoring and evaluation method and provide effective monitoring tools for agricultural water and soil conservation, ecological safety management and stable food production in Jilin Province and similar black soil areas.

Solar cell layers technology has achieved global standing in the solar cell layers deposition process, and it covers the innovative methods and techniques in significant applications. Recent solar cell layers technology has an advanced interest in a refined approach to enhance performance and highlights the importance of recent proficient procedures for manufacturing. For example, the application is used to search for novel materials for solar cells' layers to clarify the current energy crisis. The technological process and various types of solar cells depend on climate change. Among them, layers of solar cells and silicon wafer solar cells are very encouraging. Solar cell layers technology has led to solar cells being a more reasonable active option in design and production. The productivities facilitated by new solar cells still need to be enhanced for the various processes involved in the additional enhancement from Copper Indium Gallium Selenide (CIGS) microfilms to solar cell crystal structure dye-sensitized solar cells. The hydrophobic coating works as an anti-dust coating, enhancing efficiency and decreasing the cost of cleaning solar cells. In Saudi Arabia Majmaah City, most solar projects are in dry regions, where the dusty weather reduces solar cell efficiency. Therefore, combining these two properties and applying an anti-reflective and superhydrophobic coating will increase solar cell efficiency by 20%. Solar cells' crystal structure results are substituted with layers or new materials to balance environmental impact and toxic nature.

Despite huge effort has been devoted to the design of the initiators and reaction conditions, it remains challenging to synthesize high molecular weight polypeptides with conventional solution phase synthesis. In this work, surface-initiated vapor deposition polymerization (SI-VDP) was utilized to graft synthetic polypeptides poly (γ-benzyl L-glutamate) (PBLG) from polystyrene (PS) resin beads by ring-opening polymerization of N-carboxyanhydrides (NCAs). It was demonstrated for the first time that high molecular weight bulk PBLG (> 500,000) could be readily obtained within one hour via solvent-free synthetic method which paves the way for the synthesis of copolypeptides with high molecular weight.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

We report on the fabrication and electrical characteristics of zinc-oxide (ZnO) based metal-insulator-semiconductor (MIS) type Schottky barrier diodes (SBHs). ZnO thin layer on the p-type silicon substrate was fabricated by atomic layer deposition (ALD). The structure and surface properties of the thin film were characterized by X-ray diffraction (XRD), atomic force microscope (AFM) and secondary ion mass spectrometer (SIMS). The current-voltage (I-V) characteristics of Al/ALD-grown ZnO/p-Si diodes were measured under dark at room temperature. The electrical parameters such as ideality factor (n), series resistance (R_s) and barrier height (ϕ_b) of the diodes were analyzed using standard thermionic emission (TE) theory, Norde and Cheung method. The barrier height value obtained from I-V and Cheung method was found to be 0.73 eV and 0.76 eV, respectively. The interface state density (Dit) of the diodes was determined from the I-V characteristics. The nonideal behavior of measured parameters suggested the presence of interface states. The obtained results showed that the prepared diode can be used for NIR Schottky photodetector applications.

This paper analyses the health and performance of 12-stage axial compressor of the TV3-117VM/VMA turboshaft operated in a desert environment. The results of the dimensional control of 4,800 worn blades are analysed to model the wear process. Operational experience and numerical simulations are used to assess the effectiveness of an Inlet Particle Separator. Numerical modal analysis is performed to generate the Campbell diagram of worn blades and identify resonant blade vibration which can lead to high cycle fatigue (HCF). It is shown that the gradual loss of the stall margin over time determines the serviceability limits of compressor blades. Recommendations setting out go / no-go criteria are made to maintenance and repair organisations.

The use of the LMD technology as a manufacturing and repairing technique in industrial sectors like the die and mold and aerospace is increasing within the last decades. Research carried out in the field of LMD process situates argon as the most usual inert gas, followed by nitrogen. Some leading companies have started to use helium and argon as carrier and shielding gas, respectively. There is therefore a pressing need to know how the use of different gases may affect the LMD process due to there is a lack of knowledge with regard to gas mixtures. The aim of the present work is to evaluate the influence of a mixture of argon and helium on the LMD process by analyzing single tracks of deposited material. For this purpose, special attention is paid to the melt pool temperature, as well as to the characterization of the deposited clads. The increment of helium concentration in the gases of the LMD processes based on argon will have three effects. The first one is a slightly reduction of the height of the clads. Second, an increase of the temperature of the melt pool. Last, smaller wet angles are obtained for higher helium concentrations.

Bangladesh is located in the alluvial floodplain of the Ganges–Brahmaputra–Meghna (GMB) river system and its numerous tributaries. In this country, the frequency, as well as severity, of riverbank erosion is high. To examine the impacts of riverbank erosion on rural food security, a baseline survey was conducted in Zajira, Bangladesh. The findings show that most people in the study area are affected by riverbank erosion. Moreover, agricultural production is gradually decreasing as a result of loss of farmland due to the catastrophe and its impacts. In some cases, people lose their entire homestead and are left with few income opportunities and low purchasing power. Consequently, they face the constant threat of a food crisis. The affected people follow some coping mechanisms to face these stressful situations, such as relying on less expensive or less preferred food items. While the local-government authorities have implemented some programmes to assist them, such as food aid and social-safety-net schemes, these are insufficient, due to the government's limited institutional resources and capacities. These findings suggest that for formulating effective rural-development plans, assessing the impact of riverbank erosion on the food security of people living in the affected areas is a prerequisite.

A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser-wire based Directed Energy Deposition is demonstrated with a novel modification: site-specific changes to the controller set-point were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary 3D-printed component geometry. The present work shows that, through this technique, it is possible to print a specific geometry that occurs beyond the actual toolpath of the print head. This is denoted as an extra-toolpath geometry and is fundamentally different from other methods of generating component features in metal AM. A proof-of-principle experiment is presented in which a complex oak leaf geometry was embossed on an otherwise ordinary double-bead wall made from Ti-6Al-4V. The process is introduced and characterized primarily from a controls perspective with reports on the performance of the control system, the melt pool size response, and the resulting geometry. The implications of this capability, which extend beyond localized control of bead geometry to the potential mitigations of defects and functional grading of component properties, are discussed.

The main purpose of this paper is to present a system to detect extrusion failures in Fused Deposition Modelling (FDM) 3D printers by sensing that the filament is moving forward properly. After several years using these kind of machines, authors detected that there is not any system to detect the main problem in FDM machines. Authors thought in different sensors and used the Weighted Objectives Method, one of the most common evaluation methods, for comparing design concepts based on an overall value per design concept. Taking into account the obtained scores of each specification, the best choice for this work is the optical encoder. Once the sensor is chosen, it is necessary to design de part where it will be installed without interfering with the normal function of the machine. To do it, photogrammetry scanning methodology was employed. The developed device perfectly detects the advance of the filament without affecting the normal operation of the machine. Also, it is achieved the primary objective of the system, avoiding loss of material, energy and mechanical wear, keeping the premise of making a low-cost product that does not significantly increase the cost of the machine. This development has made it possible to use the printer with remains coil filament, which were not spent because they were not sufficient to complete an impression and also printing models in two colours with only one extruder.

In this paper, a novel synthesis for a chemical precursor for nanocrystalline VO2 coatings is elaborated. The compatibility of the precursor towards the substrate is optimized for spin coating. This is done by subjecting multiple solvents to contact angle measurements. A suitable thermal treatment is developed to densify the coating and to induce crystallization. Afterwards the microstructure of the coating is investigated using X-Ray diffraction, electron microscopy and ellipsometry techniques. To assess the thermochromic properties of the fabricated device, optical transmission experiments were conducted both at room temperature and at elevated temperature. A correlation between these thermochromic properties and coating thickness was investigated in order to obtain an optimized thermochromic device, where both high visual transparency and prominent thermochromic switching abilities are aimed for. In this work, an optimal coating thickness is proposed for a thermochromic coating with high switching ability and solar modulation.

In this study, differences in the kinetics of thermal-supported hydrolytic degradation of poly(lactic acid) (PLA) sample wet spinning fibres due to material variance in the initial molecular and supramolecular structure were analysed. The investigation was carried out at the microstructural and molecular levels by using readily available methods such as scanning electron microscopy, mass erosion measurement and estimation of intrinsic viscosity. The results show a varying degree of influence of the initial structure on the degradation rate of studied PLA fibres. The experiment shows that hydrolytic degradation at a temperature close to the cold crystallization temperature on a macroscopic level is definitely more rapid for the amorphous material, while on a molecular scale it is similar to a semi-crystalline material. Further, for the adopted degradation temperature of 90 °C, a marginal influence of pH of the degradation medium on the degradation kinetics was also demonstrated

Rheumatoid arthritis (RA) is a chronic autoimmune disease, causing inflammation of joints, cartilage destruction and bone erosion. Biomarkers and new drug targets are actively sought and progressed to improve available options for patient treatment. The Collagen Triple Helix Repeat Containing 1 protein (CTHRC1) may have an important role as a biomarker for rheumatoid arthritis, as CTHRC1 protein concentration is significantly elevated in the peripheral blood of rheumatoid arthritis patients, compared to osteoarthritis (OA) patients and healthy individuals. CTHRC1 is a secreted glycoprotein that promotes cell migration and has been implicated in arterial tissue-repair processes. Furthermore, high CTHRC1 expression is observed in many types of cancer and this is associated with cancer metastasis to the bone and poor prognosis. However, the function of CTHRC1 in RA is still largely undefined. The aim of this review is to summarize recent findings on the role of CTHRC1 as a potential biomarker and pathogenic driver of RA progression that may be linked to the pathogenic behavior of fibroblast-like synoviocytes, cartilage destruction, and bone erosion.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Current study aims to evaluate the possibilities to increase part strength by optimizing the FFF process parameters. Five different CAD models of parts with same coupling dimensions but different shape inherited from a recent study were converted into test samples with Ultimaker 2 3D printer. The main measure of success was the sample strength, defined as the load at which the first crack in the stressed area of the part appeared. Three different modifications to the FFF process with verified positive effect on interlayer bonding were applied. First modification included raising the extrusion temperature and disabling printed part cooling. Second modification consisted in reduction of the layer thickness. Third modification combined the effects of the first and the second ones. For four out of five shapes tested applied process modifications resulted in significant strengthening of the part. The shape that exhibited the best results was subject to further research by creating special printing mode. The mode included fine-tuning of three technological parameters on different stages of the part fabrication. As result it was possible to increase the part strength by 108% only by tuning printing parameters of the best shape designed with increasing its weight by 8%.

Directed energy deposition (DED) is an efficient method to fabricate functionally graded materials (FGMs) with gradient composition and complex structures, allowing for local tailoring of properties instead of the costly need for extraneous welds and joints. In this study, a FGM from stainless steel to Inconel alloy was successfully fabricated using the powder-based laser DED. A very refined grain structure has been observed in at the composition with 75 wt.% Inconel alloy content, which also exhibits the highest (entropy). For the first time, the post heat treatments, microstructure and aging precipitation behaviors of FGMs were systematically studied via experimental characterization and computation, to elucidate their effects on the gradient smoothing and mechanical properties. The diffusion and segregation of Ni, Nb and Ti elements underly the transformation mechanism between Laves, δ, γ’ and γ’’ phases during precipitation. Homogenization on FGMs not only eliminates the heterogeneity inherited from the AM process, but also provides a practical way to smoothen the gradient on composition and microstructure for the eventual good gradient properties. It has a direct influence on the following precipitation behaviors in the FGM, which highly relies on the diffusion degree of the elements in the matrix and grain boundaries. The high-throughput thermodynamic modeling and kinetic modeling were exploited to evaluate the experimental microstructure and address computational uncertainty using different thermodynamic conditions and databases, which enables an accelerated design through local tailoring of process-structure-property relationships to develop new functional materials.

Cases of road cave-ins have been reportedly increasing globally and reports have associated this phenomenon to underground soil erosion due to defective sewer pipes. As the sewer pipes age, they may develop some defects which may lead to cracks and crevices that will lead to infiltration of the soils surrounding the pipe into the pipe, leading to the formation of cavities around the pipe. Therefore, this study investigated the factors behind the causes of underground soil erosion due to defective sewer pipes and proffered solutions for combating underground soil erosion due to defective sewer pipes. The study objective included; (a) establishing how the soil particle sizes affect the internal soil erosion due to defective sewer pipes, (b) determination of the effect of defect sizes on the internal soil erosion due to defective sewer pipes, (c) establishing the effect of the embedment material used on the internal soil erosion due to defective sewer pipes, (d) investigation of the type of soil erosion mechanism in the presence of a buried sewer pipe defect caused by the groundwater infiltration process. The methodology of the study involved reviewing and analyzing secondary qualitative and quantitative data. The findings established that the defect size of the pipe, the type and characteristics of the soil and the type of embedment materials used affected erosion of soil around a defective sewer pipe.

Compressive residual stresses in thin films can inhibit crack propagation under normal or sliding contact loading, with associated enhancement of the coating apparent toughness, load bearing capacity and wear resistance. This study investigates the influence of residual stress distributions on the thin film/substrate adhesion using a nanoindenter coupled with scanning electron microscope (SEM) investigations of indentation induced failure modes. Reactive and un-reactive magnetron sputtering with ion plating was used to coat a (100) silicon substrate with aluminum nitride (AlN) with and without an aluminum (Al) adhesion layer. The presence of an Al bond layer gives additional interfacial tensile stress because of the difference in thermal expansion coefficient. Additionally, a different magnitude of residual stresses in the AlN coating was achieved by changing the applied bias voltage onto the substrate. Wafer curvature method and incremental focused ion beam (FIB) milling, combined with high-resolution in situ scanning electron microscopy (SEM) imaging and full field strain analysis by digital image correlation (DIC), were used to measure the average and in-depth stress residual stress distribution in the produced coatings. The adhesion energy was then quantified by using a nanoindentation based model. Results demonstrate that the additional tensile residual stress in the aluminum adhesion layer decrease significantly the coating adhesion, even in presence of a higher compressive stress state in the AlN top-layer. Therefore, the coatings without Al-layer showed better adhesion because of a more homogeneous compressive residual stress in comparison with the coating having Al layer, even though both groups of coatings are produced under same bias voltage. Results are discussed, and some general suggestions are made on the correlation between coating/substrate property combination and the adhesion energy of multilayer stacks. The results suggested that Al bond-layer and inhomogeneous residual stresses affected the adhesion of AlN negatively to a substrate like silicon.

In this study, TiO2 nanostructured coatings on Ti-6A-4V alloys were fabricated by two methods: H2O2 oxidation and RF sputtering. In the annealing temperature range of 25 C - 500 C, there were the peaks at 35, 37, 40 and 52 corresponding to {100}, {002}, {101} and {102} crystal planes of hcp structure of α-Ti. At the annealing temperature of 600 C, there was the presence of peaks corresponding to crystal planes of anatase and rutile TiO2. The relative intensities of anatase and rutile phases of the sample fabricated by RF sputtering were 3.62 and 10.25 %, respectively; while those of the sample fabricated by H2O2 oxidation were 21.27 and 3.20 %, respectively (The relative intensity of α-Ti phase was 100 %). The results investigated the peak shift of α-Ti phase in TiO2/Ti-6Al-4V nanostructured coatings fabricated by the two methods which was reasonably explained from the difference in the thermal expansion coefficients of Ti alloy and TiO2 components, as well as the difference in the ratio of anatase to rutile phases.

The quantity of soil loss as a result of soil erosion is dramatically increasing in catchment where land resources management is very weak. In this paper, a RUSLE model-based soil loss quanti-fication technique is presented to estimate the annual soil loss and identify the severity of the erosion in the catchment. This study uses Fincha catchment in Abay river basin as the study area to quantify the annual soil loss by implementing Revised Universal Soil Loss Equation (RUSLE) model developed in ArcGIS version 10.4. Digital Elevation Model (12.5 x 12.5), LANDSAT 8 of Operational Land Imager (OLI) and Thermal Infrared Sensor (TIRS), Annual Rainfall of 10 stations and soil maps of the catchment were used as input parameters to generate the significant factors. Rainfall erosivity factor (R), soil erodibility factor (K), cover and management factor (C), slope length and steepness factor (LS) and support practice factor (P) were used as soil loss quantification significant factors. A model builder for the RUSLE model was developed and raster map calcula-tion algebra was applied in ArcGIS version 10.4 to quantify the total annual soil loss. It was found that the quantified average annual soil loss ranges from 0.0 to 76.5 t ha-1 yr-1 was obtained in the catchment. The area coverage of soil erosion severity with 55%, 35% and 10% as low to moderate, high and very high respectively were identified. The information about the spatial variation of soil loss severity map generated in RUSLE model has a paramount role to alert land resources man-agers and all stakeholders in controlling the effects via implementation of both structural and non-structural mitigations. The results of the RUSLE model can also be further considered along with the catchment for practical soil loss quantification that can help for protection practices.

Hybrid manufacturing processes that combine additive and machining operations are gaining relevance in modern industry thanks to the capability of building complex parts with minimum material and, many times, with process time reduction. Besides, as the additive and subtractive operations are carried out in the same machine, without moving the part, dead times are reduced and higher accuracies are achieved. However, it is not clear whether the direct material deposition after the machining operation is possible or intermediate cleaning stages are required because of the possible presence of residual cutting fluids. Therefore, different LMD tests are performed on a part impregnated with cutting fluid, both directly and after the removal of the coolant by techniques such as laser vaporizing and air blasting. The present work studies the influence of the cutting fluid in the LMD process and the quality of the resulting part. Resulting porosity is evaluated and it is concluded that if the part surface is not properly clean after the machining operation, deficient clad quality can be obtained in the subsequent laser additive operation.

The information on the land use and soil conservation practice based on year 2006, 2010 and 2014, hence offering an opportunity to model the impacts of land use change on erosion, deposition and surface water runoff. Limitation in the use of hydrological models had been their inability to handle the large amount of input data that describe the heterogeneity of the natural system. In this study, a procedure that takes into account soil conservation practice based on the land use change, the response of soil erosion and sediment export from the George Town Conurbation catchment area, and average annual sediment yields were estimated for each grid cell of the watershed to identify the critical erosion areas of rural and urban planning proposes. Average annual sediment yield and data on a grid basis estimated using Universal Soil Loss Equation (USLE) and an emerging technology represented by Geographic Information System (GIS) used as a tool to produce a map for erosion rate. The changing of the land use from forest to agriculture and then to an urban area is a challenging task to research on land use demand for population, and environmental impact assessment is important for the planning of natural resources management, allowing research the modification of land use properly and implement more sustainable for long term management strategies. The challenge is to formulate strategies that would promote an integrated approach to the land use planning at an appropriate level as to address the issues that arose. Modelling for creating urban growth boundary for the George Town Conurbation must have to be controlled surface runoff and soil loss and sediment export from land use of the George Town Conurbation catchment.

Current paper investigates the influence of hardware setup and parameters of a 3D printing process based on fused filament fabrication (FFF) technology on resulting sample strength. Three-point bending of samples printed with long side oriented along Z axis was used as a measure of the interlayer bonding strength. The same CAD model was converted into NC-programs through same slicing software to be run on four different desktop FFF 3D printers, out of filament of same brand and color. Within all the printers same ranges of layer thickness values from 0.1 to 0.3 mm and feed rates from 25 to 75 mm/s were planned to be varied. All the machines demonstrated statistically almost identical values of maximum flexural strength, however the different machines exhibited maximum sample strength with different combinations of varied parameters. Among all the hardware factors observed, the most important was proved to be extruder type, direct or Bowden. This feature fundamentally changes the nature of studied parameters influence onto the resulting strength of the FFF process. For the extruders of Bowden type the length of flexible guiding tube is of great importance.All the machines demonstrated statistically almost identical values of maximum flexural strength, however the different machines exhibited maximum sample strength with different combinations of varied parameters. Among all the hardware factors observed, the most important was proved to be extruder type, direct or Bowden. This feature fundamentally changes the nature of studied parameters influence onto the resulting strength of the FFF process. For the extruders of Bowden type the length of flexible guiding tube is of great importance.

High mountain areas are an appropriate indicator of anthropogenic lead (Pb), which can reach the remote mountain ranges through long distance atmospheric transport. We compared the content of Pb in ecologically equivalent rodent species from Tian-Shan with European mountain ranges Tatra, Vitosha and Rila mountains. We used bone tissues from terminal tail vertebrae of small rodents for detection of Pb levels by using electrothermal atomic absorption spectroscopy (AAS). The tail bones of Tian-Shan rodents had significantly lower Pb levels than snow voles from Tatra mountains, but there was no significant difference in comparison with Vitosha and Rila mountains. We can conclude that Tian-Shan shows lower pollution by Pb than Tatra mountains, what may be a reason of longer lasting industrialization of north-western Europe and strongly prevailing west winds in Tatra mountains.

A controlled ammonia (NH₃) release experiment was performed at a grassland site to quantify the effect of dry deposition, at the field scale between the source and the receptors (NH₃ measurement locations), on the estimates of emission rates by means of inverse dispersion modelling. NH₃ was released for 3 hours at a constant rate of Q = 6.29 mg s⁻¹ from a grid of 36 orifices spread over an area of 250 m². The increase in line-integrated NH₃ concentration was measured with open-path optical miniDOAS devices at different locations downwind of the artificial source. Using a backward Lagrangian stochastic (bLS) dispersion model (bLSmodelR), the fraction of the modelled release rate to the emitted NH₃ (Q_bLS/Q) was calculated from the measurements of the individual instruments. Q_bLS/Q was found to be systematically lower than 1, on average between 0.69 and 0.91, depending on the location of the receptor. We hypothesized that NH₃ dry deposition to grass and soil surfaces was the main factor responsible for the observed depletion of NH₃ between source and receptor. A dry deposition algorithm based on a deposition velocity approach was included in the bLS modelling. Model deposition velocities were evaluated from a ‘big‑leaf’ canopy resistance analogy. Canopy resistances (generally termed Rc) that provided Q_bLS/Q = 1 ranged from 75 to 290 s m⁻¹, showing that surface removal of NH₃ by dry deposition can plausibly explain the original underestimation of Q_bLS/Q. The inclusion of a dry deposition process in dispersion modelling is crucial for emission estimates, which are based on concentration measurements of depositing tracers downwind of homogeneous area sources or heterogeneously distributed hot spots, such as e.g. urine patches on pastures in the case of NH₃.

Over the last decade, a significant literature has emerged that advocates the potential of different Additive manufacturing (AM) technologies and printable polymeric materials. Nevertheless, large scale printing and complex geometric shapes, with curvatures and non-planar layer deposition, are a challenging process for the traditional gantry-based machine. The 3 degrees of freedom cartesian configuration restricted their capability to planar layered printing and restricted part dimensions. To date, many researchers have used industrial robots to overcomes this limitation. This review gives the reader a good overview of the FDM technique due to its scalability, cost efficiency and a wide range of material printability. A strong emphasis is laid on the PLA and PLA-based composites as promising materials for the FDM process applications. The second part of this paper links the successful use of these materials in the traditional printing process to large scale printing using the robot-based FDM process. This survey presents representative setups for robot-based AM and works that have been used these setups for non-planar material deposition. Finally, we conclude this paper by identifying opportunities for realizing new functional capabilities by exploiting robot-based AM, and we also present the future trends in this area.

The composition of fine-ground lead zirconate-titanate powder Pb(Zr_0.52Ti_0.48)O₃, suspended in PZT and bismuth titanate (BiT) solutions, is deposited on the curved surface of IN718 and IN738 nickel-based supper alloy substrates up to 100 µm thickness. Photochemical metal organic and infiltration techniques are implemented to produce smooth, semi-dense, and crack-free random orientated thick piezoelectric films as piezo-sensors, free of any dopants or thickening polymers. Every single layer of the deposited films is heated at 200 °C with 10 wt.% excess PbO, irradiated by UV lamp (365 nm, 6 watt) for 10 minutes, pyrolyzed at 400 °C, and subsequently annealed at 700 °C for one hour. This process is repeated successively until reaching the desired thickness. Au and Pt thin films are deposited as the bottom and top electrodes using evaporation and sputtering methods, respectively. PZT/PZT and PZT/BiT composite films are then characterized and compared to similar PZT and BiT thick films deposited on the similar substrates. The effect of composition and deposition process is also investigated on the crystalline phase development and microstructure morphology as well as dielectric, ferroelectric and piezoelectric properties of piezo-films. The maximum remnant polarization of P_r = 22.37 ± 0.01, 30.01 ± 0.01 µC/cm², the permittivity of ε_r = 298 ± 3, 566 ± 5 and piezoelectric charge coefficient of d₃₃ = 126, 148 m/V were measured versus the minimum coercive field of E_c = 50, 20 kV/cm for the PZT/PZT and PZT/Bit thick films, respectively. The thick film piezo-sensors are developed to be potentially used at frequency bandwidth of 1–5 MHz for rotary structural health monitoring and also in other industrial or medical applications as a transceiver.

Soil erosion seriously affects vineyards. In this study, the influence of two plant covers on soil moisture and the effect of different physiographic conditions on runoff and sediment yields were evaluated in a rainfed vineyard formed by four fields (NE Spain) during 15 months. One field had spontaneous vegetation as plant cover and three fields had a cover crop of common sainfoin. The vineyards’ rows were dry and stable, whereas the inter-row areas were wet although very variable, and the corridors were wet and very stable. Soil moisture in the inter-row areas with Common sainfoin was much higher than in the rows (62% - 70%) whereas this difference was lower with spontaneous vegetation (40%). Two runoff and sediment traps (STs) were installed in two ephemeral gullies, and 26 time-integrated surveys (TIS) done. The mean and maximum runoff yields were 9.8 and 30.7 l TIS^–1 in ST2 and 13.5 and 30.2 l TIS^–1 in ST3. The mean turbidity was 333 and 19 g l^–1, and the maximum sediment yields were 41,260 and 2,778 g TIS^–1 in ST2 and ST3. Changes in the canopy covers (grapevines and plant covers) and rainfall parameters explained the runoff and sediment dynamics.

In this paper, we present a study of various ZnO/SiO2-stacked thin film structures for flexible micro-energy harvesting devices. Two groups of micro-energy harvesting devices, SiO2/ZnO/SiO2 micro-energy generators (SZS-MGs) and ZnO/SiO2/ZnO micro-energy generators (ZSZ-MGs), were fabricated by stacking both SiO2 and ZnO thin films, and the resulting devices were characterized. With a particular interest in the fabrication of flexible devices, all the ZnO and SiO2 thin films were deposited on ITO-coated PEN substrates using an RF magnetron sputtering technique. The effects of the thickness and/or position of the SiO2 films on the device performance were investigated by observing the variations of output voltage in comparison with that of a control sample. As a result, compared to the ZnO single-layer device, all the ZSZ-MGs showed much better output voltages, while all the SZS-MG showed only slightly better output voltages. Among the ZSZ-MGs, the highest output voltages were obtained from the ZSZ-MGs where the SiO2 thin films were deposited using a deposition power of 150 W. Overall, the device performance seems to depend significantly on the position as well as the thickness of the SiO2 thin films in the ZnO/ SiO2-stacked multilayer structures, in addition to the processing conditions.

Abstract: Polylactic acid (PLA) is brittle in nature with extensive deformation property. For improvement of the end-use quality, it is of significant importance to enhance the producibility of fused deposition modeling (FDM)-printed objects in PLA. The purpose of this investigation is to boost toughness and to reduce the production cost of the FDM-printed tensile test samples with the desired part thickness. To attain the research purpose number of experiments are designed and analyzed by the Response Surface Method (RSM). The statistical analysis is performed to deal with this concern considering layer thickness, infill percentage, and extruder temperature as controlled factors. The tensile test specimens are printed based on the designed experiments, and the tensile strength tests are conducted by SANTAM 150 universal testing machine based on ASTM D638. The honeycomb internal fill pattern is applied for the production of light-weight and high-strength specimens. The area under Force- Extension curve up to fracture is acquired as the toughness of the printed specimens. This study also developed a modeling process using ANN and ANN-GA techniques for developing an accurate estimation for toughness, part thickness, and production cost as dependant variables. Results were evaluated by correlation coefficient and RMSE values. According to the modeling results, ANN-GA as a hybrid ML technique could successfully improve the accuracy of modeling about 7.5, 11.5 and 4.5 % for toughness, part thickness, and production cost, respectively, in comparison with those for the single ANN method. In the other side, the optimization results confirm that the optimized specimen is cost-effective and able to comparatively undergo deformation, which develops the usability of printed PLA objects. The research is accomplished under the constraints of PLA compatibility with existing fused deposition modeling setup without changing the functional hardware/software of the machine. Although the mechanical properties and dimensional accuracy of PLA have already been studied, there is little literature on the toughness of the printed PLA with honeycomb internal fill pattern.

The spray drying process causes the buildup of an unspecified and unique pattern of wall deposits on the wall. The powder recovery of fruit juice by spray dryer is associated with stickiness problems because of the nature of food which contains low molecular weight sugars and organic acids, which have a low glass transition temperature (T_g). The surface properties of oxygen plasma treated-PTFE substrate were evaluated by using the different parameters of Plasma Enhanced Chemical Vapour Deposition (PECVD) prior to spray drying analysis. In this study, the fabrication method of nearly perfect superhydrophobic surfaces through plasma treatment with oxygen gas was generated and utilized. The plasma-treated PTFE were deposited from a fixed flow rate of oxygen gas with 30 cm³/min by varying the deposition time from 1 to 15 minutes to induce the hydrophobic surface of the PTFE substrate. The characterization techniques used to determine the morphology and chemical bonding of the substrate are field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FTIR), respectively. The hydrophobicity of the glass samples was determined by the water droplet contact angle. Sample prepared at radio frequency (RF) power of 90W for 15 minutes duration of treatment time showed porous and spongy like microstructure which correlates with the best performance of a good contact angle which creates the superhydrophobicity regime (171^o). Surface morphology analysis using scanning electron microscopy (SEM) showed changes in its roughness in the surface-treated glass substrate. The success of this method produced a huge potential for solving most of the food processing issues which relate to biofouling (e.g., powder stickiness) that would otherwise struggle to improve high productivity and recovery.

In this study, silver-strontium doped hydroxyapatite (AgSr-HA)/chitosan composite coatings were deposited on stainless steel (SS) substrate via electrophoretic deposition (EPD) technique. The EPD parameters such as the concentration of Ag Sr-HA particles in the suspension, applied voltage and deposition time were optimized on by the Taguchi Design of Experiment (DoE) approach. DOE approach elucidated that the “best” coating was obtained at; the deposition voltage of 20V, deposition time of 7 minutes, and at 5 g/L of Ag Sr-HA particles in the suspension. The optimum coatings were characterized by using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy. SEM images confirmed the deposition of chitosan/Ag Sr-HA on the SS substrate. The wettability studies indicated the hydrophilic nature of the chitosan/Ag Sr-HA coatings, which confirmed the suitability of the developed coatings for orthopedic applications. The average surface roughness of the chitosan/Ag Sr-HA coatings was in a suitable range for the attachment of bone marrow stromal cells. Chitosan/Ag Sr-HA coatings showed a potent antibacterial effect against the Gram-Positive and Gram-negative bacteria.

We describe the direct formation of mixed-phase (1T and 2H) MoS2 layers on Si as a photocathode via atomic layer deposition (ALD) for application in the photoelectrochemical (PEC) reduction of water to hydrogen. Without typical series-metal interfaces between Si and MoS2, our p-Si/SiOx/MoS2 photocathode showed efficient and stable operation in hydrogen evolution reactions (HERs). The resulting performance could be explained by spatially genuine device architectures in three dimensions (that is, laterally homo and vertically heterojunction structures). The ALD-grown MoS2 overlayer with the mixed-phase 1T and 2H homojunction passivates light absorber and surface states and functions as a monolithic structure for effective charge transport within MoS2. It is also beneficial in the operation of p-i-n heterojunctions with inhomogeneous barrier heights due to the presence of mixed-phase cocatalysts. The effective barrier heights reached up to 0.8 eV with optimized MoS2 thicknesses, leading to a 670 mV photovoltage enhancement without employing buried Si p-n junctions. The fast-transient behaviors via light illumination show that the mixed-phase layered chalcogenides can serve as efficient cocatalysts by depinning the Fermi levels at the interfaces. A long-term operation of ~ 70 h was also demonstrated in a 0.5 M H2SO4 solution.

Additive manufacturing (AM) are used in several industries such as automotive, aerospace, and medical sciences. One of the most common devices used in additive manufacturing is fused deposition modeling (FDM) 3D printers. This fabrication method has different inputs that affect the quality of the parts. In this research, the bending fatigue properties of polylactic acid (PLA) biomaterial made with a 3D printer are investigated. To demonstrate the influence of printing parameters on fatigue lifetime, standard specimens with nozzle diameters of 0.2-0.6 mm, extruder temperature of 180-240°C, and print speed of 5-15 mm/s were printed. After performing fully-reversed bending fatigue tests, it was found that printed specimens at 180°C have the best fatigue lifetime in most cases. Accordingly, fatigue behavior improved by reducing the nozzle diameter. Printing at lower temperatures also improved fatigue lifetime. The printing speed affected the slope of the S-N diagram, known as the fatigue strength exponent.

Land use and land cover change (LULCC) is a critical factor for enhancing the soil erosion risk and land degradation process in the Wabi Shebelle Basin. Up-to-date spatial and statistical data on basin-wide erosion rates can provide an important basis for planning and conservation of soil and water ecosystems. The objectives of this study were to examine the magnitude of LULCC and consequent changes in the spatial extent of soil erosion risk, and identify priority areas for Soil and Water Conservation (SWC) in the Erer Sub-Basin, Wabi Shebelle Basin, Ethiopia. The soil loss rates were estimated using an empirical prediction model of the Revised Universal Soil Loss Equation (RUSLE) outlined in the ArcGIS environment. The estimated total annual actual soil loss at the sub-basin level was 1.01 million tons in 2000 and 1.52 million tons in 2018 with a mean erosion rate of 75.85 t ha^–1 y^–1 and 107.07 t ha^–1 y^–1, respectively. The most extensive soil loss rates were estimated in croplands and bare land cover, with a mean soil loss rate of 37.60 t ha^–1 y^–1 and 15.78 t ha⁻¹ y⁻¹, respectively. The soil erosion risk has increased by 18.28% of the total area, and decreased by 15.93%, showing that the overall soil erosion situation is worsening in the study area. We determined SWC priority areas using the Multi-Criteria Decision Rule (MCDR) approach, indicates that the top three levels identified for intense SWC account for about 2.50%, 2.38%, and 2.14%, respectively. These priority levels are typically situated along the steep slopes in Babile, Fedis, Fik, Gursum, Gola Oda, Haramaya, Jarso, and Kombolcha districts that need emergency SWC measures.

Fatty acids (FAs) represent an important class of metabolites, impacting on membrane building blocks and cellular regulatory networks. In nature, prokaryotes are characterized with the most impressing FA structural diversity and the highest relative contents of free fatty acids (FFAs). Thereby, nitrogen-fixing bacteria (order Rhizobiales), often found in symbiosis with legumes, attract a special interest. Indeed, FAs impact on the structure of rhizobial nodulation factors, required for successful infection of plant root. Although the FA patterns can be addressed by GC- and LC-MS, these methods are time-consuming and suffer from compromised sensitivity, low stability of derivatives and artifacts. In contrast, MALDI-TOF-MS represents an excellent platform for high-efficient metabolite fingerprinting, also applicable to FFAs. Therefore, here we propose a simple and straightforward protocol for high-throughput relative quantification of FFAs in rhizobia by the combination of Langmuir technology and MALDI-TOF-MS, which is featured with high sensitivity, accuracy and precision of quantification. Here we propose a step by step procedure comprising rhizobia culturing, pre-cleaning, extraction, sample preparation, mass spectrometric analysis, data processing and post-processing. To demonstrate the analytical potential of the protocol we illustrate it by a case study – comparison the FFA metabolomes of two rhizobia species - Rhizobium leguminosarum and Sinorhizobium meliloti.

Mechanical robustness, biocompatibility, and antibacterial performances are key features for materials suitable to be used in tissue engineering applications. In this work, we investigated the link existing between structural and functional properties of TiCu(Ag) thin films deposited by physical vapor deposition magnetron sputtering on Si substrates. The thin films were characterized by X-ray diffraction (XRD), nanoindentation, atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The TiCu(Ag) thin films showed complete amorphous structure and improved mechanical properties in comparison with pure Ti films. However, for contents in excess of 20% Ag, we observed the appearance of nanometric Ag crystallite. The TiCu(Ag) thin films displayed excellent biocompatibility properties, allowing adhesion and proliferation of the human fibroblasts MRC-5 cell line. Moreover, all the investigated TiCu(Ag) alloy display bactericidal properties, preventing the growth of both Pseudomonas aeruginosa and Staphylococcus aureus. Results obtained from biological tests have been correlated to the surface structure and microstructure of films. The excellent biocompatibility and bactericidal properties of these multifunctional thin films opens to their use in tissue engineering applications.

Soils provide important regulating ecosystem services and have crucial implications for human well-being and environmental conservation. However, soil degradation and particularly soil erosion jeopardize the maintenance and existence of these services. This study explores the spatio-temporal relationships of soil erosion to understand the distribution patterns of sediment retention services in mainland Portugal. Based on Corine Land Cover maps from 1990 to 2018, the InVEST Sediment Delivery Ratio (SDR) model was used to evaluate the influence of sediment dynamics for soil and water conservation. Spatial differences in the sediment retention levels were observed within the NUTS III boundaries, showing which areas are more vulnerable to soil erosion processes. Results indicated that the Region of Leiria, Douro and the coastal regions have decreased importantly sediment retention capacity over the years. However, in most of the territory (77.52%) changes in sediment retention were little or not important (i.e., less than 5%). The statistical validation of the model proved the consistency of the results, highlighting the usefulness of this methodology to analyse the state of soil erosion in the country. These findings can be relevant to support strategies for more efficient land use planning regarding soil erosion mitigation practices.

Engineering properties of bedrock materials at Badlands National Park were used to develop models for Park managers to assess slope erosion and stability for fossil resource protection. Six fully instrumented sites were used to document slope conditions. Bedrock consisted of Oligocene White River Group rocks. Bulk erosion rates correlated to grain size with silty-sandy materials producing higher mass erosion rates as a function of the silt-to-clay ratio and plastic index. Data indicated that as grain size decreased, plastic index increased leading to a decrease in erodibility. These parameters were used to construct a grain-size proxy, ψ, that was substituted for grain size, D, in Bagnold’s entrainment equation and provided significant improvement in calculation of critical entrainment velocities for fine-grained materials. Hydraulic analyses of slope and pediment surface processes indicated surface roughness was a controlling factor and materials washed from rough steep slopes were effectively transported across smooth low-angle pediments with slope-to-pediment angle ratios of nearly 6:1. Slope stability modeling of ten slopes produced high factors of safety for all slopes, even under saturated conditions and was attributable to clay cohesion. All results were used to construct models that predicted years until net slope erosion equaled 2.5 cm (1 inch). Using these results, Park managers were advised to visit erosion-prone sites on a 1 to 6 year schedule, based on site geology and slope aspect, to adequately protect critical fossil resources from destruction.

Traditionally, studies on freeze–thaw erosion have used the analytic hierarchy process (AHP) to calculate the weight of evaluation factors, however, this method cannot accurately depict the fuzziness and randomness of the problem. To overcome this disadvantage, the present study has proposed an improved AHP method based on the cloud model to evaluate the impact factors in freeze–thaw erosion. To establish an improved evaluation method for freeze–thaw erosion in Tibet, the following six factors were selected: annual temperature range, average annual precipitation, slope, aspect, vegetation coverage, and topographic relief. The traditional AHP and the cloud model were combined to determine the weight of the impact factors, and a consistency check was performed. The comprehensive evaluation index model was used to evaluate the intensity of freeze–thaw erosion in Tibet. The results show that freeze–thaw erosion is extensive, stretching over approximately 66.1% of Tibet. The problem is the most serious in Ngari Prefecture and Nagqu. However, mild erosion and moderate erosion, accounting for 37.1% and 25.0%, respectively, of the total freeze–thaw erosion are the most widely distributed. The evaluation results for the freeze–thaw erosion was confirmed to be consistent with the actual situation. In brief, this study provided a new approach to evaluate the conditions of freeze–thaw erosion quantitively in Tibet.

Controlling functional properties of matter and combine them for engineering a functional device is nowadays a common direction of scientific community. For instance, heterogeneous magnetic nanostructures can make use of different types of geometrical and compositional modulations to achieve the control of the magnetization reversal along with the nano-entities and thus enabling the fabrication of spintronic, magnetic data storage and sensing devices, among others. In this work, diameter modulated FeNi nanowires are fabricated paying special effort to obtain sharp transition regions between two segments of different diameters (from about 450 nm to 120 nm), enabling precise control over the magnetic behavior of the sample. Micromagnetic simulations performed on single bi-segmented nanowires predict a double step magnetization reversal where the wide segment magnetization switches near 200 Oe through a vortex domain wall, while at 500 Oe the magnetization of the narrow one is reversed through a corkscrew like mechanism. Finally, these results are confirmed with magneto-optic Kerr effect measurements at the transition of isolated bi-segmented nanowires. Furthermore, macroscopic vibrating sample magnetometry is used to demonstrate that the magnetic decoupling of nanowire segments is the main phenomenon occurring over the entire fabricated nanowires.

Retrogressive breach failures or coastal flow slides occur naturally in the shoreface in fine sands near dynamic tidal channels or rivers. They sometimes retrogress into beaches, shoal margins and river banks where they can threaten infrastructure and cause severe coastal erosion and flood risk. Ever since the first reports were published in the Netherlands over a century ago, attempts have been made to understand the geo-mechanical mechanism of flow slides. In this paper we have established that events, observed during the active phase, are characterized by a slow and steady retrogression into the shoreline, often continuing for many hours. This can be explained by the breaching mechanism, as elaborated in this paper. Recently, further evidence has become available in the form of video footage of active events in Australia and elsewhere, often publicly posted on the internet. All these observations justify the new term ‘retrogressive breach failure’ (RBF event). The mechanism has been confirmed in small-scale flume tests and in a large-scale field experiment. With a better understanding of the geo-mechanical mechanism, current protection methods can be better understood and new defense strategies can be envisaged. In writing this paper, we hope that the coastal science and engineering communities will better recognize and understand these intriguing natural events.

The impact of ponds on basins has recently started to receive its well–deserved scientific attention. In this study, pond–induced impacts on soil erosion and sediment transport were investigated at the scale of the French Claise basin. In order to determine erosion and sediment transport patterns under current conditions, the CORINE erosion and SWAT models were used. The impact of ponds on the studied processes was revealed by means of land cover change scenarios, using ponded versus pondless inputs. Results show that under current conditions (pond presence), 12.48% of the basin corresponds to no–erosion risk zones (attributed to the dense pond network), while 65.66% corresponds to low–erosion risk, 21.68% to moderate–erosion risk and only 0.18% to high–erosion risk zones. The SWAT model revealed that ponded sub–basins correspond to low sediment yields areas, in contrast to the pondless sub–basins, which yield appreciably higher erosion rates. Under the alternative scenario, erosion risks shifted to 1.12%, 0.52%, 76.8% and 21.56% for no, low, moderate and high–erosion risks, respectively, while the sediment transport pattern of the Claise completely shifted to higher sediment yield zones. This approach solidifies ponds as powerful man–induced modifications to hydro/sedimentary processes.

Field and numerical investigations at Happisburgh, East coast of England, UK, sought to characterize beach thickness and determine geologic framework controls on coastal change. After a major failure of coastal protection infrastructure, removal of about 1 km of coastal defense along the otherwise protected cliffed coastline of Happisburgh triggered a period of rapid erosion over 20 years of ca. 140 m. Previous sensitivity studies suggested that that beach thickness plays a major role in coastal recession. These studies were limited, however, by a lack of beach volume data. In this study, we have integrated the insights gained from our understanding of the Quaternary geology of the area, a novel non-intrusive passive seismic survey method, and a 3D novel representation of the subsurface source and transportable material into a coastal modelling environment to explore the role of beach thickness on the back wearing and down wearing of the cliffs and consolidated platform, respectively. Results show that beach thickness is non-homogeneous along the study site: we estimate that the contribution to nearshore sediment budget via platform down wearing is of a similar order of magnitude as sediment lost from the beach and therefore non-negligible. We have provided a range of evidence to support the idea that the Happisburgh beach is a relatively thin layer perched on a sediment rich platform of sand and gravel. This conceptualization differs from previous publications, which assumes that the platform was mostly till and fine material. This has direct implication on the regional sediment management of along this coastline. The present study contributes to our understanding of a poorly known aspect of coastal sediment budgeting and outlines a quantitative approach that allows for simple integration of geological understanding for coastline evolution assessments worldwide.

Today, contamination from heavy metals in the atmosphere is a global concern. Efficient detection techniques are therefore necessary if heavy metal exposure levels in different media are to be determined. The voltammetry method for in situ detection of heavy metal ions is a very sensitive electrochemical method. This thesis explores emerging developments in electrode alteration, materials production and experimental optimization. An electrochemical sensing platinum nanoparticle in the tantalum electrode is provided by means of an Ion Beam Sputtering Deposition (IBSD). The electrode was made with a Pt solution, sputtered simultaneously with hydrochloric acid corrosion on tantalum substrate. In the study of heavy metal ions, for example, the platinum nanoparticle electrodes as prepared were used Square wavelength voltammetry (OSWV) Hg²⁺, Cu²⁺ and Ag²⁺. The porous electrodes were observed in a broader range by the Pt nanostructure electrode for heavy metal ions. Furthermore, the susceptibility to detection has been shown to be saturated as the thickness of the layer electrode exceeded 50 nm. For Hg²⁺ 0,003-1 M, for Cu²⁺ 0,005-3 M and for Ag²⁺ the linear detection scale is 0,009-4 M. There has also been good reusability and repeatability. In addition, a scan electron microscope (SEM) used to study platinum electrode forming process and nanostructure. This electrode will have interesting applications in sensing systems.

A potassium bromide KBr material, which has been widely used as the key element in the Fourier spectrometers and as the output window of the IR-lasers, has been studied with good advantage via applying the carbon nanotubes in order to modify the potassium bromide surface. The laser oriented deposition method has been used to place the carbon nanotubes at the matrix material surface in the vertical position at the different electric field varied from 100 to 600 V×cm-1. The main idea of the improvement of the spectral properties of the potassium bromide structure is connected with the fact that the refractive index of the carbon nanotubes is substantially less than the refractive index of the studied material, and the small diameter of the carbon nanotubes allows one to embed these nano-objects in the voids of the lattice of the model matrix systems. Moreover, the mechanical characteristics and wetting features of the potassium bromide structures have been investigated under the condition mentioned above. Analytical and quantum-chemical simulations have supported the experimental results.

Tungsten oxides play a pivotal role in a variety of modern technologies e.g., switchable glasses, wastewater treatment, and modern gas sensors. Metallic tungsten is used as armor material, for e.g., gas turbines as well as future fusion power devices. In the first case, oxides are desired as functional materials, while in the second case, oxides can lead to catastrophic failures, so avoiding the oxidation of tungsten is desired. In both cases, it is crucial to understand the reactivity of tungsten oxides with other chemicals. In this study, the different reactivities of tungsten oxides with the highly-oxophilic beryllium are studied and compared. Tungsten-(IV)-oxide and tungsten-(VI)-oxide layers are prepared on a tungsten substrate. In the next step, a thin film of beryllium is evaporated on the samples. In consecutive steps, the sample is heated in steps of 100 K from r. t. to 1273 K. The chemical composition is investigated after each experimental step by high-resolution X-ray photoelectron spectroscopy (XPS) of all involved core levels as well as the valence band. A model is developed to analyze the chemical reactions after each step. In this study, we find that tungsten trioxide was already reduced by beryllium at r. t. and started to react to form the ternary compounds BeWO₃ and BeWO₄ at temperatures starting from 673 K. However, tungsten dioxide is resistant to reduction at temperatures of up to 1173 K. In conclusion, we find WO₂ to be much more chemically resistant to the reduction agent Be than WO₃.

This study aims to evaluate a new approach in modeling gully erosion susceptibility based on deep learning neural network (DLNN) model, ensemble Particle swarm optimization (PSO) algorithm with DLNN (PSO-DLNN) and comparing these approaches with common artificial neural network (ANN) and support vector machine (SVM) models in Shiran watershed, Iran. For this purpose, 13 independent variables affecting gully erosion susceptibility in the study area, including altitude, slope, aspect, plan curvature, profile curvature, drainage density, distance from river, land use, soil, lithology, rainfall, , stream power index (SPI), topographic wetness index (TWI), were prepared. Also, 132 gully erosion locations were identified during field visits. Data for modeling were divided into two categories of training (70%) and testing (30%). Receiver operating characteristic (ROC) parameters including sensitivity, specificity, negative predictive value (NPV), positive predictive value (PPV) and area under curve (AUC) were used to evaluate the performance of the models. The results showed that, the AUC values from ROC with considering testing datasets of PSO-DLNN is 0.89 and which is associated with superb accuracy. Rest of the models also associated with optimal accuracy and near about PSO-DLNN model; the AUC values from ROC of DLNN, SVM and ANN for testing datasets are 0.87, 0.85 and 0.84 respectively. The PSO algorithm has updated and optimized the weights of DLNN model, and as a result, the efficiency of this model in predicting gully erosion susceptibility has increased. Therefore, it can be concluded that the use of DLNN model and its ensemble with PSO algorithm can be used as a novel and practical method in predicting the susceptibility of gully erosion that helps planners and managers in managing and reducing the risk of this phenomenon.

Stainless steel grade AISI 304 is one of the most widespread modern structural material, alas its sliding wear and cavitation wear resistance are limited. Thus, AlTiN and TiAlN coatings can be deposited for increasing the resistance to wear of stainless steel components. The aim of the work was to investigate the cavitation erosion and sliding wear mechanisms of magnetron sputtered AlTiN and TiAlN coatings deposited on SS304 stainless steel. Films surface morphology and structure were examined using a profilometer, light optical microscope (LOM) and scanning electron microscope (SEM). The mechanical properties (hardness, elastic modulus) were tested by nanoindentation tester. The adhesion of deposited coatings was determined by means of the scratch test and Rockwell test. Cavitation erosion tests were performed according to ASTM G32 (vibratory apparatus) with stationary specimen procedure. Sliding wear tests were conducted using a nano-tribo testes i.e. ball-on-disc apparatus. Wear mechanisms are strongly contingent upon the structure and morphology of the tested materials. In relation to stainless steel substrate, the PVD films present a superior resistance to sliding wear and cavitation erosion. Higher resistance was noticed for AlTiN than for TiAlN film, mainly due to its superior hardness and elastic modulus. Cavitation erosion mechanism of both, AlTiN and AlTiN coatings is prone to embrittlement, imputable to fatigue processes that result in coating rupture and spallation that consist in coating fragmentation, formation of pits and finally detachment from the substrate. Additionally, films nanoindentation results measured before and after cavitation testing indicate changes in coatings structure, that acknowledged wear mechanism that starts with coating internal delamination in flake spallation mode. In contrary to PVD coatings, steel substrate is characterized by developed cavitation erosion wear with roughened surface and plastically deformed, semi-brittle, eroded surface. Sliding wear of thin films is based on micro-ploughing mechanism. For stainless steel adhesive sliding wear mode and plastic deformation with smearing, material transfer and grooving were observed. It was confirmed that various fluid machinery components made from austenitic stainless steel that undergo cavitation erosion, can be prevented by deposition of AlTiN and TiAlN films.

Ti-6Al-4V (TC4) titanium alloy parts were successfully fabricated by laser melting deposition (LMD)technology in this study. Proper normalizing temperatures were presented in detailed for bulk LMD specimens. Optical microscope, scanning electron microscopy, X-ray diffraction and electronic universal testing machine were used to characterize the microstructures, phase compositions, the tensile properties and hardness of the TC4 alloy parts treated using different normalizing temperature. The experimental results showed that the as-fabricated LMD speceimens microstructures mainly consisted of α-Ti phase with a small amount of β-Ti phase. After normalizing treatment, in the area of α-Ti phase, the recrystallized length and width of α-Ti phase both increased. When normalizing in the (α+β) phase field, the elongated primary α-Ti phase in the as-deposited state was truncated due to the precipitation of β-Ti phase and became a short rod-like primary α-Ti phase. In as-fabricated microstructure, the β-Ti phase was precipitated between different short rod-shaped α-Ti phases distributed as basketweave. After normalizing treatment at 990 for two hours with subsequent air cooling, the TC4 titanium alloy had significant different microstructures from original sample produced by LMD. Moreover, the mismatch of tensile and hardness property was mitigated in this heat treatment. So the normalizing treatment methods and temperature can be qualified as a prospective heat treatment of titanium alloy fabricating by laser melting deposition.

A new generation of nano-technologies is expanding solid propulsion capabilities and increasing their relevance for versatile and manoeuvrable micro-satellites with safe high-performance propulsion. We propose the innovative concept, connected with application of new synergistic effect of the energetic materials performance enhancement and reaction zones programming for the next generation small satellite multimode solid propulsion system. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon, by the properties of the energetic materials reaction zones and by localization of the energy release areas. This synergistic effect can be provided through application of the functionalized carbon-based nanostructured metamaterials as a nano-additives along with simultaneous manipulating by their properties through the electrostatic field. Mentioned effect will be controlled through predictive programming both by the spatial structure and physics-chemical properties of the functionalized carbon-based nano-additives and through the electromagnetic control of the self-organized wave pattern excitation and micro- and nano- scale oscillatory networks in the energetic material reaction zones. Suggested new concept makes it possible to increase the energetic material regression rate and increase the thrust of the solid propulsion system with minimal additional energy consumption.

A series of defective ZSM-5 zeolites (~300 nm, SiO₂/Al₂O₃ ratio of 55, 100, 400 and 950) were intentionally prepared and systematically studied by XRD, SEM, ²⁹Si MAS NMR, argon physisorption, NH₃-TPD and FT-IR technologies. The nature, the amount and the accessibility of the acid sites of defective ZSM-5 zeolites are greatly different from reported ZSM-5 zeolites with perfect crystal structure. The co-existed strong Brønsted acid sites (Si(OH)Al) and weak Brønsted acid sites (hydroxyl nests) over defective ZSM-5 zeolites might lead to unique catalytic function. Zn(C₂H₅)₂ was grafted onto defective ZSM-5 zeolites through chemical liquid deposition (CLD) method. Interestingly, FT-IR spectroscopy studies find that Zn(C₂H₅)₂ was preferentially grafted on the hydroxyl nests with weak acidity rather than the Si(OH)Al groups with strong acidity over different defective ZSM-5 zeolites. Particularly, home-built operando dual beam FTIR-MS was applied to study the catalytic performance of Zn species locating at different sites of defective ZSM-5 zeolites under n-hexane transformation. Results show that Zn species grafted over hydroxyl nests obtain better dehydrogenation performance than Zn species over framework aluminum. This study provides guidance for the rational design of highly efficient alkane dehydrogenative aromatization catalysts.

This manuscript deals with the cavitation erosion resistance of low-velocity oxy-flame (LVOF) sprayed Al2O3–40%TiO2/NiMoAl cermet coatings, a new functional application of cermet coatings. The aim of the study was to investigate the cavitation erosion mechanism and determine the effect of feedstock powder ratio (Al2O3–TiO2/NiMoAl) of LOVF cermet coatings on their cavitation erosion resistance. As-sprayed coatings were investigated for roughness, porosity, hardness, Young’s modulus. Microstructural characteristics of the cross-section and the surface of as-sprayed coatings were examined by light optical microscopy (LOM) and scanning electron microscopy (SEM) equipped with the EDS and XRD methods. Coatings cavitation tests were conducted in accordance with the ASTM G32 standard with usage of reference samples made from steel, copper and aluminum alloys. Cavitation erosion resistance was measured by weight and volume loss, and normalised cavitation erosion resistance was calculated. Surface eroded due to cavitation was examined in successive time intervals by LOM and SEM-EDS. On the basis of coating properties and cavitation investigations, a phenomenological model of the cavitation erosion of Al2O3–40%TiO2/NiMoAl cermet coatings was elaborated. General relationships between their properties, microstructure and cavitation wear resistance were established. The Al2O3–40%TiO2/NiAlMo composite coating containing 80% of ceramic powder has a higher cavitation erosion resistance than the reference aluminium alloy.

Double suction centrifugal pump installed along the Yellow River faces the serious sediment erosion due to the high sediment content which cause the poor operation efficiency of pump unit. The particle motion characteristics and erosion characteristics in the pump under different flow rates and different particle concentrations were numerically simulated based on the particle track model of solid-liquid two-phase flow. The results show that the flow rate has a significant effect on the particle tracks and the erosion caused by the particles in the impeller. The total erosion rate is positively correlated with the flow rate, and increases with the increase of flow rate. The vortex and secondary flow in the impeller have obvious influence on the particle trajectory, which increases the particle concentration at the trailing edge of the pressure surface and intensifies the impact erosion in this area. The particles carried by the vortex intensifies the local erosion. The particle concentration mainly affects the erosion rate, but has little effect on the erosion position. The in-fluence of flow rate on the pump erosion is greater than that of the particle properties. These results provide a reference for optimization of the design of anti-erosion blades of the double-suction pump and regulation-operation of pumping station.

Structural self-organizing and pattern formation are universal and key phenomena observed during growth and cluster-assembling of the carbyne-enriched nanostructured metamaterials at the ion-assisted pulse-plasma deposition. Fine tuning these universal phenomena opens access to designing the properties of the growing carbyne-enriched nano-matrix. The structure of bonds in the grown carbyne-enriched nano-matrices can be programmed by the processes of self-organization and auto-synchronization of nanostructures. We propose the innovative concept, connected with application of the universal Cymatics phenomena during the predictive growth of the carbyne-enriched nanostructured metamaterials. We also propose the self-organization approach for increase stability of the long linear carbon chains. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon and their distribution by the spatial structure and properties of the nanostructured metamaterial grows region through the new synergistic effect. Mentioned effect will be provided through the vibration-assisted self-organized wave patterns excitation along with simultaneous manipulating by their properties through the electric field. We propose to use acoustic activation of the plasma zone of nano-matrix growing. Interaction between the inhomogeneous electric field distribution generated on the vibrating layer and the plasma ions will serve as the additional energizing factor controlling the local pattern formation and self-organizing of the nano-structures. Suggested concept makes it possible to provide precise predictive designing the spatial structure and properties of the advanced carbyne-enriched nanostructured metamaterials.

An electrochemical sensing platinum nanoparticle in the tantalum electrode is provided by means of an Ion Beam Sputtering Deposition (IBSD). The electrode was made with a Pt solution, sputtered simultaneously with hydrochloric acid corrosion on tantalum substrate. In the study of heavy metal ions, for example, the platinum nanoparticle electrodes as prepared were used Square wavelength voltammetry (OSWV) Hg²⁺, Cu²⁺ and Ag²⁺. The porous electrodes were observed in a broader range by the Pt nanostructure electrode for heavy metal ions. Furthermore, the susceptibility to detection has been shown to be saturated as the thickness of the layer electrode exceeded 50 nm. For Hg²⁺ 0,003-1 M, for Cu²⁺ 0,005-3 M and for Ag²⁺ the linear detection scale is 0,009-4 M. There has also been good reusability and repeatability. In addition, a scan electron microscope (SEM) used to study platinum electrode forming process and nanostructure. This electrode will have interesting applications in sensing systems.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

Bioglasses are highly adoptable bone substitute materials, which can be combined with so-called therapeutic ions. These ions have shown to influence underlying molecular processes of the bone regeneration cascade. Moreover, it is known that bone substitutes induce an immune reaction within their implantation area involving macrophages and their pro- and anti-inflammatory subtypes dependent on their chemical composition. However, only poor knowledge exists regarding the influence of therapeutic ions onto the immune reactions and the associated bone healing. Thus, the aim of this work was to investigate the influence of strontium- and copper-doped bioglasses on the induction of M1- and M2-macrophages as well as the implant bed vascularization. (2) Methods: For this study, two alkali glasses were produced on basis of ICIE-16 bioglass via the melt-quench route with the addition of 5 wt% copper or strontium (ICIE16-Cu and ICIE16-Sr). Pure ICIE16 and 45S5 bioglasses were used as control materials. The bioactivity (ion release), chemical composition and the surface pattern were investigated, as well as an in vivo experiment was performed using the subcutaneous implantation model in rats. (3) Results: SEM imaging showed different formations of hydroxyapatite on the surfaces of the bioglass systems after submersion in simulated body fluid. EDX analysis confirmed the doping process by showing the release kinetics. Copper-doped bioglass exhibited a higher ion release than strontium-doped bioglass. Copper induced both a low immune cell migration and triggered a low number of M1- and M2-macrophages but also of blood vessels. The strontium-containing bioactive glass induced higher numbers of M1-macrophages after 30 days. Both copper- and strontium-doped bioglasses induced comparable numbers of M2-macrophages as found in the control groups. (4) Conclusions: Bioglass doping with copper and strontium did not exhibit significant influence on the foreign body response or the implantation bed vascularization in vivo. However, the prepared bioglass systems seemed to be biocompatible.

A conventional 2D numerical model is improved by incorporating three submodels to consider different effects of secondary flow and a module for cohesive sediment transport. The model is applied to a meandering reach of Yangtze River to investigate secondary flow effects on cohesive sediment deposition, and a preferable submodel is selected based on the flow simulation results. Sediment simulation results indicate that the improved model predictions are in better agreement with the measurements in planar distribution of deposition as the increased sediment deposits caused by secondary current on the convex bank have been well predicted. Secondary flow effects on predicted amount of deposition become more obvious during the period when the sediment load is low and velocity redistribution induced by the bed topography is evident. Such effects vary with the settling velocity and critical shear stress for deposition of cohesive sediment. The bed topography effects can be reflected by the secondary flow submodels.

The sand-dust horizontal flux is an important parameter for the study on aeolian sand transport, as well as an important foundation. In this study, a field experiment was developed to measure the data of aeolian transport and microclimate during different dust events with an auto sand sampler, a piezoelectric saltation sensor (H11-Sensit) and a 10 m high meteorological tower in Ta Zhong, the hinterland of the Taklimakan Desert from July to August in 2010. Then, the sampling efficiency of auto sand sampler and horizontal dust flux of near surface were analyzed based on observed data. The results were as follows: sand collector skip turnover increased with the increase of the intensity of dust weather frequency increases, the power function relationship y=2.115 x0.9841, R2 = 0.9206, flip frequency per minute increased from 0.2794 times to 1.3041 times, change is obvious; With the strength of the weather, time to flip the average sediment is shrinking. Sandstorm weather, skip to flip a volume of 3.7160 g, grade I flying sand weather flip a volume of 4.0275 g, the amount of class II flying sand weather turns over a 5. 0035g.The horizontal dust flux of different dust events that calculated with the equation Q=256M; the maximum of one dust event was about 190.335 kg, and the minimum was 1.2 kg. Overall, the sand transportation rate increased with wind speed. However, the changes of sand transportation rate did not quite fit in with wind speed during some dust events, and in this case the corresponding surface temperature was significantly higher. The experimental data obtained can provide theoretical basis for regional sand control and enacting effective engineering measures.

The preparation of immobilized graphene–based photocatalyst layers is highly desired for environmental applications. In this study, the preparation of an immobilized reduced graphene oxide (rGO)/TiO₂ composite by electrophoretic deposition (EPD) was optimized. It enabled quantitative deposition without sintering and without the use of any dispersive additive. The presence of rGO had beneficial effects on the photocatalytic degradation of 4-chlorophenol in an aqueous solution. A marked increase in the photocatalytic degradation rate was observed, even at very low concentrations of rGO. Compared with the TiO₂ and GO/TiO₂ reference layers, use of the rGO/TiO₂ composite (0.5 wt% of rGO) increased the first-order reaction rate constant by about 70%. This enhanced performance was due to the increased formation of hydroxyl radicals that attacked the 4-chlorophenol molecules. The direct charge transfer mechanism had only limited effect on the degradation. Thus, EPD-prepared rGO/TiO₂ layers appear to be suitable for environmental application.

Laser Powder Directed Energy Deposition (LP-DED) is an Additive Manufacturing process in which a laser beam is used to generate a melt pool onto a substrate. The additional material, in form of powder material, is fed into the generated melt pool and a raised track is obtained. The LP-DED process is very powerful for different applications such as the repair operations and the production of functionally graded material, however the application is still limited and one of the main reasons is related to the lack of knowledge in the physics of the process mechanisms. The process is influenced by a huge number of parameters and three main mechanisms can be identi-fied. These mechanisms are the powder flow, the generation of the molten pool and the solidifica-tion process and for each of these mechanisms the process parameters have a different relevance. In this paper, a review of the main mechanisms and the relationship between the process parame-ters and the outcome of each step of the process is presented.

Soil erosion is one of the most important environmental problems which can have various negative consequences, such as land degradation affecting the sustainable development and the agricultural production, especially for developing countries like Tunisia. Moreover, soil erosion is a major problem around the world because of its effects on soil fertility by nutriment loss and siltation in water bodies. Apart from this, soil erosion by water is the most serious type of land loss in several regions both locally and globally. This study evaluated regional soil erosion risk through the derivation of appropriate factors, using the Revised Universal Soil Loss Equation (RUSLE), which was applied to establish a soil erosion risk map of the whole Tunisian territory and to identify the vulnerable areas of the country. RUSLE model take into account all the factors playing a major role in erosion processes, namely the erodibility of soils, topography, land use, rainfall erosivity and anti-erosion farming practices. The equation is thus implemented under Geographic Information System (GIS) “Arc GIS Desktop”. The results indicated that Tunisia has a serious risk of soil water erosion, showing that 6.43% of the total area of the country is affected by a very high soil loss rate estimated at more than 30 t/ha/year and 4.20% are affected by high mean annual soil loss ranging from 20 to 30 t/ha/year. The most eroded areas were identified in west southern, central and western parts of the country. The spatial erosion map can be used as a decision support document to guide decision-makers towards better land management and provide the opportunity to develop management strategies for soil erosion prevention and control in the global scale of Tunisia.

The 2022-2023 Chilean summer showed increased temperatures and similar burned area, compared to the 2016-2017 season, where more than 500,000 hectares were compromised, mainly in the rural areas. After a brief review, it is revealed that the effects of forest fires on soil and hydrological properties are barely debated in Chile. Here, we showed a climatological analysis where temperature records in the 2016-2017 season were unusual, as well as another unexpected increase in the summer of 2022-2023, resulting in high-severity fires known as ‘mega-fires’ or “storm-fires”. Mega-fires affect forest plantations and native forests mainly from 33º S (Maule Region) to 39º S (Los Ríos Region) and they are expected to become frequent due to climate change, moving from the north to the south. We present an overview of the influence of wildfires on soil components in the most affected areas (inland, Coastal, and Andes ranges), their hydrological impacts, and potential erosion risk due to high winter precipitation. We propose several management practices that could help to prevent or mitigate these events, including pre-and post-fire interventions, such as afforestation and seeding, selective logging, mulching, erosion barriers, soil preparation, and dam monitoring. We argue that any effective plan in fire-prone and affected areas should include a combination of actions taken at the hillslope scale at integral ecosystem management, whose effectiveness should be monitored and verified regionally at the watershed scale.

With the decline in fossil fuels, hydrogen-based alternatives provide a reliable and clean source for sustainable energy generation. In these endeavors, photochemical splitting for hydrogen production through tandem cells has been the source of much theoretical and experimental research in science. Much focus has been placed on interfacial band gap engineering as one of the most promising routes in the generation of hydrogen.This present work explores sputtering of n-silicon to form the active electrode in a n-Si | n-TiO₂ tandem cell and investigates the effect of variations in sputtering and post sputtering treatment parameters (rapid thermal annealing and long cycle annealing) for successful deposition of crystalline Silicon. The samples were successfully characterized via Raman Spectroscopy, X-ray Diffraction and Optical Transmission Spectroscopy to ascertain prevalent crystalline order and optical band gap, under different sputtering and post-sputtering conditions. Relevant conclusions were drawn to ascertain the best possible deposition parameters of n-Si for photocatalytic water splitting.

We have determined Hf isotopic compositions of 12 samples associated with the giant El Teniente Cu-Mo deposit, Chile. The samples range in age from ≥8.9 to 2.3 Ma and provide information about the temporal evolution of their magmatic sources from the Late Miocene to Pliocene. Together with previously published data, the new analysis indicate a temporal decrease of 10 εHf(t) units, from +11.6 down to +1.6, in the 12.7 m.y. from 15 to 2.3 Ma. These variations imply increasing incorporation of continental crust through time in the magmas that formed these rocks. The fact that the samples include mantle-derived olivine basalts and olivine lamprophyres suggests that these continental components were incorporated into their mantle source, and not by intra-crustal contamination (MASH). We attribute the increase, between the Middle Miocene and Pliocene, of crustal components in the subarc mantle source below El Teniente to be due to increased subduction erosion and transport of crust into the mantle. The deposit formed above a large, long-lived, vertically zoned magma chamber that developed due to compressive deformation and persisted between the period ~7 to 4.6 Ma. Progressively more hydrous mantle-derived mafic magmas feed this chamber from below, providing heat, H₂O, S and metals, but no unique “fertile” Cu-rich magma was involved in the formation of the deposit. As the volume of these mantle-derived magmas decreased from the Late Miocene into the Pliocene, the chamber crystallized and solidified, producing felsic plutons and large metal-rich magmatic-hydrothermal breccias that emplaced Cu and S into the older (≥8.9 Ma) mafic host rocks of this megabreccia deposit.

The application of metal-matrix composite coatings for protecting and improving the service life of sliding components has demonstrated to have the potentials of meeting the requirements of a diverse range of engineering industries. Recently, a significant body of research has been devoted to study the mechanical and tribological performance of dispersion-strengthened MCrAlY coatings. These coatings belong to a class of emerging wear-resistant materials, offering improved properties and being considered as promising candidates for the protection of engineering structural materials exposed to tribological damage, especially at elevated temperature regimes. This paper attempts to comprehensively review the different reinforcements used in the processing of MCrAlY-based alloys and how they influence the mechanical and tribological properties of the corresponding coatings. Further, the major fabrication techniques together with their benefits and challenges are also reviewed. Discussion on the failure mechanisms of these coatings as well as the main determining factors are also included. In addition, a comprehensive survey of studies and investigations in recent times are summarized and elaborated to further substantiate the review.

In this work, the manufacture of thin walls with sharp corners has been optimized by adjusting the limits of a 3-axis cartesian kinematics through data recorded and analyzed off-line, such as axis speed, acceleration and the positioning of the X and Y axes. The study was carried out with two powder materials (SS316L and IN718) using the directed energy deposition process with laser. 1 mm thick walls were obtained with only one bead per layer and straight/sharp corners at 90º. After adjusting the in-position parameter G502 for positioning precision on the FAGOR 8070 CNC system, it has been possible to obtain walls with minimal accumulation of material in the corner, and with practically constant layer thickness and height, with a radii of internal curvature between 0.11 and 0.24 mm for two different precision configuration. The best results have been obtained by identifying the correct balance between the decrease in programmed speed and the precision in the positioning to reach the point defined as wall corner, with speed reductions of 29% for a programmed speed of 20 mm/s and 61% for a speed of 40 mm/s. The walls show minimal defects such as residual porosities, and the microstructure is adequate.

In this article, metallic additive manufacturing (AM) processes were classified and demonstrated. AM technology can be applied to a wide range of industrial areas because of its great feasibility in the design and manufacturing of various complex parts. The main factor that distinguishes various metallic AM processes from each other is the deposition method. Deposited metal can be imported in the form of melt or semi-solid. AM technology also covers a wide range of materials like aluminum, titanium, and many other alloys. Some of the common applications of metallic AM processes are the quick manufacturing of the parts which utilized in various industries like medical, automotive, aerospace, and jewelry industries. AM can help to fabricate parts that are impossible to be manufactured by other processes.

An amorphous silicon carbide (SiC) membrane with H2 permeance of 1.2E-7 mol･m^-2･s^-1･Pa^-1 and excellent H₂/CO₂ selectivity of 2600 at 673 K was successfully synthesized on a Ni-gamma-alumina-coated alpha-alumina porous support by counter diffusion chemical vapor deposition (CDCVD) using silacycrobutane (SCB) at 788 K. The dominant permeation mechanism for He and H₂ in the temperature range 323-673 K was activated diffusion. The SiC active layer was formed in Ni-gamma-Al₂O₃ intermediate layer. The thermal expansion coefficients mismatch between SiC active layer and Ni-gamma-Al₂O₃-coated alpha-Al₂O₃ porous support was eased by the low decomposition temperature of SiC source and membrane structure.

: TiAl6V4 alloy is widely used in selective laser melting and direct laser melting. In turn, works devoted to the issue of how the track stacking scheme affects the value of mechanical properties is not enough. The influence of the Ti6Al4V alloy track trajectories on the microstructure and mechanical properties during direct laser deposition is studied in this article for the first time. The results were obtained on the influence of «parallel» and «perpendicular» technique of laying tracks in direct laser synthesis. All studied samples have a microstructure typical of the hardened two-phase condition titanium. It is shown that the method of laying tracks and the direction of load application during compression testing relative to the location of the tracks leads to a change in the ultimate strength of the Ti-6Al-4V alloy from 1794 to 1910 MPa. The plasticity of the Ti-6Al-4V alloy obtained by direct laser alloying can vary from 21.3 to 33.0% depending on the direction of laying the tracks and the direction of the compression test. The hardness of alloys varies in the range from 409 to 511 HV and depends on the method of laying the tracks and the direction of hardness measurements.

The objective of this research is to conduct a comparative analysis between rectangular-shaped ASTM D3039 specimens with different angles (0°, 15°, and 90°) and various tensile test specimens based on ASTM and ISO standards, all 3D-printed using polyethylene terephthalate glycol (PETG) material through FDM. The study aimed to assesses the weak spot commonly found at the neck of the specimens. Two different printing orientations, namely flat and on-edge, were investigated, and a comprehensive examination and comparison were made regarding the variations in tensile strength, E-modulus, strain, and elongation at break among the tested samples. Additionally, the broken areas was evaluated, and a numerical study utilizing the finite element method (FEM) was conducted to identify stress risers' locations in each specimen type. The experimental results demonstrated that the ASTM D3039-0° specimen exhibited the best tensile properties when printed in the on-edge orientation, while the flat orientation yielded the best results in terms of the broken area. On the other hand, the ISO 527-2 specimens displayed the lowest tensile properties, regardless of the printing orientation. The study highlighted the enhanced tensile properties achieved with the rectangular shape. Specifically, the tensile strength of ASTM D3039-0° was 17.87% and 21% higher than that of the ISO 527 geometry shape for the flat and on-edge orientations, respectively. The numerical analysis indicated that the ISO 527-2 specimen had either no or minimal stress raisers, and the higher stresses observed in the narrow section were isolated from the gripping location.

This study presents of the microsphere-based fiber-optic sensor with the ZnO ALD coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100°C to 300°C, with a 10°C step. The interferometric signal is used to control whether the microstructure is intact. Spectrum shift of a reflected signal is used to conclude changes in measured parameter for the sensor with a 100 nm coating, while the reflected signal intensity is an indicator during measurements executed by a sensor with a 200 nm coating. With changing temperature, the peak position or intensity of a reflected signal also changes. The R2 coefficient of the presented sensors indicates a linear fit of over 0.99 to the obtained data. The sensitivity of the sensors, investigated in this study, equals 103.5 nW/°C and 0.019 nm/°C for ZnO thickness of 200 nm and 100 nm, respectively.

This report describes the collection of a large dataset (6930 measurement) on dimensional error in the fused deposition modeling (FDM) additive manufacturing process for full-density parts. Three different print orientations were studied, as well as seven raster angles (0°, 15°, 30°, 45°, 60°, 75°, and 90°) for the rectilinear infill pattern. All measurements were replicated ten times on ten different samples to ensure a comprehensive dataset. Eleven polymer materials were considered: acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), high-temperature PLA, wood-composite PLA, carbon-fiber-composite PLA, copper-composite PLA, aluminum-composite PLA, high-impact polystyrene (HIPS), polyethylene terephthalate glycol-enhanced (PETG), polycarbonate, and synthetic polyamide (nylon). The samples were ASTM-standard impact testing samples, since this geometry allows the measurement of error on three different scales; the nominal dimensions were 3.25mm thick, 63.5mm long, and 12.7mm wide. This dataset is intended to give engineers and product designers a benchmark for judging the accuracy and repeatability of the FDM process for use in manufacturing of end-user products.

Changes in land-use have been observed in banana-based systems in the African Great Lakes region affected by Xanthomonas wilt disease (XW) of banana. Through participatory focus group discussions (FGDs) and the 4-cell method, changes in land-use were retrospectively assessed in 13 XW-affected landscapes/villages along a 230 km transect from Masisi (XW arrived in 2001) to Bukavu (XW arrived around 2014) in eastern Democratic Republic of Congo during 2015. The four-cell chart ranked land-use by mapping the area under production and the number of households involved in production. Farmers’ perceptions on the sustainability of new land-uses were also documented. Soil nutrient content and erosion levels were measured for five major land-use options/ trajectories on 147 fields across 55 farms in three landscapes along the transect. From being ranked the most important crop (92% of landscapes i.e. produced on large areas of land and by many households) before XW outbreaks, its importance had declined with most households in 36% of the landscapes growing it on smaller farms while in 64% of cases by few households on smaller pots. Farmers uprooted entire banana mats or fields, expanding land under other crops, mainly beans, taro, sweet potato, cassava, maize, coffee and eucalyptus. Species richness did not change at landscape level, though 21 crops were introduced at farm level. Land-use for banana is however still perceived to be more sustainable due to its multi-functional roles. Soils under banana plots were found in general to be better in their chemical attributes while high erosion levels (Mg ha-1 year-1) were observed under cassava (1.7-148.9) compared with banana (0.3-10.7) and trees (0.3-5.9). The current shift away from banana could thus have profound effects on supply of key services and sustainability of the production systems. This study offers a good basis/entry point for interventions in the XW-affected landscapes.

This study compared the use of chip and slash to minimize the loss of sediment on newly constructed forest road slopes and investigated the annual amount of sediment loss on bare forest road slopes. A runoff block (sample field) was established for each of the four designated test sites (two cutslopes and two fillslopes). Each block had three runoff plots. One of the runoff plots was left empty for the control (CNT), while chip (C) and slash (S), respectively, were deposited in the other two. A total of 108 water samples were taken from the test sites and the amount of their suspended sediment calculated in the laboratory. As a result of this study, it was determined that the amount of soil loss in the control plots was about 1.26 times higher than in the slash plots and 2.21 times higher than in the chip plots. According to the results of variance analysis on the amounts of sediment, a statistically significant difference was found between the suspended sediment quantities transported on the road slopes (P <0.05). However, no statistically significant difference between the suspended sediment quantities transported in the plots and the other variables of aspect, gradient or road slope was revealed by the t-test (P >0.05).

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

The paper formulates requirements for a polymer material for molding products from it by fused deposition modeling. A methodology for evaluating the suitability of a polymer or composite of thereof in 3D printing technology has been developed. A graphic representation of the developed methodology in the form of a temperature-shear rate logarithm diagram is proposed. Application of the proposed methodology makes it possible to simplify the development of new materials for 3D printing by fused deposition modeling both at the stage of selecting the components of the polymer composition and at the stage of its subsequent approbation.

Raindrop erosion is a significant materials limiting issue. It can affect materials for transportation and renewable energy converters such as wind turbines as well as all external structures used in the construction industries. In such cases, the raindrop effects can occur over a wide range of impact velocities and particles sizes. In understanding tribological variable effects, it is useful to study using reference materials. This is because the reference material is well characterized, from previous knowledge of the tribological and corrosion patterns. Further, the well established chemical composition and stochiometry of the corrosion products provide some background understanding of how effectively, during tribological action, the surface scale adheres to the substrate. In this study, a carbon steel was used as a reference to study the effects of velocity and drop diameter in a whirling arm erosion test rig. The results were used to establish the conditions where corrosion was accelerated and the environments where aerodynamic effects may have resulted in droplets being deflected the surfaces. Erosion maps were generated to illustrate such mechanisms based on the results.

The study aims to elaborate a neural model and algorithm for optimising hardness and porosity of coatings and thus ensure that they have superior cavitation erosion resistance. Al2O3-13wt.%TiO2 ceramic coatings were deposited onto 316L stainless steel by atmospheric plasma spray (ASP). The coatings were prepared with different values of two spray process parameters: the stand-off distance and torch velocity. Microstructure, porosity and microhardness of the coatings were examined. Cavitation erosion tests were conducted in compliance with the ASTM G32 standard. Artificial neural networks (ANN) were employed to elaborate the model, and the multi-objectives genetic algorithm (MOGA) was used to optimise both properties and cavitation erosion resistance of the coatings. Results were analysed with Matlab software by Neural Network Toolbox and Global Optimization Toolbox. The fusion of artificial intelligence methods (ANN+MOGA) is essential for future selection of thermal spray process parameters, especially for the design of ceramic coatings with specified functional properties. Selection of these parameters is a multicriteria decision problem. The proposed method made it possible to find a Pareto front, i.e. trade-offs between several conflicting objectives – maximising the hardness and cavitation erosion resistance of Al2O3-13%TiO2 coatings and, at the same time, minimizing their porosity.

Among the agricultural practices promoted by the Common Agricultural Policy to increase soil functions, the use of cover crops is a recommended tool to improve the sustainability of Mediter-ranean woody crops such as olive orchards. However, there is a broad range of cover crop ty-pologies in relation to its implementation, control and species composition. In that sense, the in-fluence of different plant species on soil quality indicators in olive orchards remains unknown yet. This study describes the effects of four treatments based on the implementation of different ground covers (CC-NAT, CC-GRA and CC-MIX) and conventional tillage (TILL) on soil erosion, soil physicochemical and biological properties, and soil microbial communities after 8 years of cover crop establishment. Our results have demonstrated that the presence of a temporary cover crop (CC), compared to a soil under tillage (TILL), can reduce soil losses and maintain good soil physicochemical properties and modify greatly the structure and diversity of soil bacterial com-munities and its functioning. The presence of a homogeneous CC of gramineous (Lolium rigidum or Lolilum multiflorum) (CC-GR) for 8 years significantly increased the functional properties of the soil as compared to TILL; although the most significant change was a modification on the bacte-rial community composition that was clearly different from the rest of treatments. On the other hand, the use of a mixture of plant species (CC-MIX) as a CC for only two years although did not modify greatly the structure and diversity of soil bacterial communities compared to the TILL soil, induced significant changes on the functional properties of the soil, and reverted those properties to a level similar to that of an undisturbed soil that had maintained a natural cover of spontaneous vegetation for decades (CC-NAT).