Oriental melons have a relatively short shelf life as they are harvested during the summer season and susceptible to cold-induced injuries. Typical chilling injury when stored at 4℃ is expressed as browning of the fruit suture. To prolong the shelf life and reduce browning of the fruit, the effects of modified atmosphere packaging (MAP), X-tend modified atmosphere (MA)/modified humidity (MH) bulk packaging (XF), and polyethylene (PE) packaging, on oriental melons were investigated during storage at 4℃ and 10℃ for 14 days and under retail display conditions at 20℃. The O2 concentrations in PE packages stored at 4℃ and 10℃ ranged from 17.4–18.5%, whereas those in XF packages were reduced to 16.3–16.6%. The CO2 content of XF package (4.2–4.6%) was higher than that of PE package (1.4–1.9%) stored at 4℃ or 10℃. Relative humidity (RH) saturated in the PE packages but not in the XF packages after seven days of storage. Furthermore, PE packages performed better at maintaining melon weight and firmness than XF packages during storage at 10℃ for 14 days and under retail display conditions at 20℃. PE and XF packages effectively reduced the browning index of the peel and white linear sutures of oriental melons compared with the unpackaged control during cold storage at 4℃, and this observation was maintained at the retail display condition at 20℃. The enhanced CO2 levels, reduced O2 levels, and optimal RH values that were provided by the MAP, prevented the browning symptoms and improved the marketability and shelf life of oriental melons.

Supermarkets in Port Harcourt (PH) city, Nigeria, predominantly rely on diesel electricity generation due to grid instability, leading to high cost of electricity prices. Although solar photovoltaic (PV) systems have been proposed as an alternative, these supermarkets have yet to adopt them, mainly due to high investment costs and a lack of awareness of the long-term financial and environmental benefits. This paper examines the technical and economic practicality of a PV system for these supermarkets using the PVsyst software and a spreadsheet model. Solar resources showed that PH has a daily average solar radiation and temperature of 4.21 kWh/m2/day and 25.73℃, respectively. Market Square, the supermarket with the highest peak power demand of 59.8 kW, and a 561 kWh/day load profile, was chosen as a case study. A proposed PV system with a power capacity of 232 kW, battery storage capacity of 34,021 Ah, a charge controller size of 100 A/560V, and an inverter with a power rating of 60V/75 kW has been designed to meet the load demand. The economic analysis showed a $266,936 life cycle cost, $0.12 per kWh levelized cost of electricity (LCOE), 4-year simple payback time, and a 20.5% internal rate of return (IRR). The PV system is feasible due to its positive net present value (NPV) of $165,322 and carbon savings of 582 tCO2/year.

There are numerous hazards found on the farms. Most of them are ignored, which might cause the farmer to pay later in terms of his ill health, potential injuries or death. The current article discusses some of the common issues such as dust and air quality concerns; environmental (weather) stressors and psychological stressors; noise and hearing protection; and tractor safety and seatbelt use. And finally, the recommendations to overcome the hazards are discussed.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of simulation and statistical results of EO with other optimization techniques showed that EO is more effective and superior.

The aim of this study was to explore perspectives of occupation health personnels (OHPs) regarding education and training of mineworkers on occupational noise induced hearing loss (ONIHL) and its impact on mineworkers’ hearing. Qualitative, in-depth telephonic and face-to-face interviews were conducted with 16 OHPs comprising representatives from the state, employer and labour as well as audiologists and occupational health hygienists. Purposive and snowball sampling were utilized to recruit participants. Data were analysed using inductive thematic analysis. Findings revealed that mineworkers have a superficial awareness and knowledge of the impact of noise on their hearing and health. Moreover, OHPs are not knowledgeable on how mineworkers are educated on ONIHL and its latent consequences. Furthermore, language, low levels of education and literacy as well as the financial constraints were factors that had a negative impact on raising awareness and training mineworkers. There is a need to prioritize health literacy among mineworkers. Additionally, audiologists need to play an active role in educating mineworkers about the effects of excessive exposure to noise. There is a need to take into account literacy levels and language barriers in planning training material for mineworkers.

Soil-transmitted helminthiasis (STH), a neglected tropical disease (NTD) remains a major health problem all over the world including Ghana, which has STH prevalence of 25.4%. To control the disease, the government of Ghana currently concentrates on implementing mass drug administration (MDA) efforts focusing only among school-aged children. However, various studies have suggested that focusing on only a specific group for MDA may not be cost-effective. Moreover, some adults such as teachers and school-workers spend large fraction of their time with children, who shed more parasite in environment due to unhygienic behavior, and thus have a higher risk of getting infected as compared to other adults. In this study we use a mathematical model to evaluate age-structured and risk-based policies for implementing MDA while capturing transmission dynamics of STH in Ghana. A cost model was developed that included various costs related to MDA to study cost-effectiveness of current policies of MDA in Ghana against novel policies to control STH in Ghana. We carry out analysis for five different scenarios— I: no MDA (baseline), II: current MDA policy (focusing children) in Ghana, III: MDA for different age groups (adults and children groups) for unlimited budget, IV: MDA for different age groups with limitations of number of individuals treated, and, V: MDA for different groups based on their risk of getting infected (adults school workers (high-risk group), adults non-school workers and children groups). Our results suggest that it might be more cost-effective to allocate treatment through MDA to at least some proportion of adults along with children. In case of unlimited budget, the best strategy in Scenario IV would be to treat approximately 22% of adults and approximately 45% of children. The most cost-effective among the 5 scenarios is suggested through scenario V, where high-risk adults group and children are provided MDA at higher level than low-risk adults. In conclusion, age-structured and risk-based allocation of treatment and resources is crucial to reducing STH load in developing countries.

Intending to analyze the role of nuclear power in an integrated energy system, we used the IESA-Opt-N cost minimization model focusing on four key themes: system-wide impacts of nuclear power, uncertain technological costs, flexible generation, and cross-border electricity trade. We demonstrate that the Levelized Cost of Energy (LCOE) alone should not be used to demonstrate the economic feasibility of a power generation technology. For instance, under the default techno-economic assumptions, particularly the 5% discount rate and exogenous electricity trade potentials, it is cost-optimal for the Netherlands to invest in 9.6 GWe nuclear capacity by 2050. However, its LCOE is 34 €/MWh higher than offshore wind. Moreover, we found that nuclear power investments can reduce demand for variable renewable energy sources in the short term and higher energy independence (i.e., lower imports of natural gas, biomass, and electricity) in the long term. Furthermore, investing in nuclear power can reduce the mitigation costs of the Dutch energy system by 1.6% and 6.2% in 2040 and 2050, and 25% lower national CO₂ prices by 2050. However, this cost reduction is not significant given the odds of higher nuclear financing costs and longer construction times. In addition, this study has shown that lower financing costs (e.g., EU taxonomy support) considerably reduce the relevance of nuclear cost uncertainties on its investments. Furthermore, we demonstrate that the economic feasibility of national nuclear power investments can vary considerably depending on the cross-border electricity trade assumptions. Additionally, we found that lowering the cost of small modular reactors has more impact on their economic feasibility than increasing their generation flexibility. In conclusion, under the specific assumptions of this study, nuclear power can play a complementary role (in parallel to the wind and solar power) in supporting the Dutch energy transition from the sole techno-economic point of view.

This paper presents a detailed description of three methodologies to electrify the rural households of small loads with reliable and economical method using solar energy as input source of power. It is observed that high DC voltage is better and economical solution rather than AC based solar systems and low voltage DC systems. In this paper, three methodologies were analysed to select the right combination of portable converters with low prices, which may further enhance the energy access and affordability to common people. The proposed three methodologies were tested through action research in collaboration with a team of scientists and technical experts of National Institute of Solar Energy. The comparative analysis is carried out on three different converters, various kind of house loads and types of power supply i.e. AC/DC. The performance, quality and economic evaluation has been carried out with the help of MATLAB SIMULINK and other measuring instruments specific for solar photovoltaic systems. The derived results were analysed and inferences made for use in village household loads and their income groups. Further, a three-step analytical framework on village-level power energy efficient power at affordable power preposition was presented. This study will help in the designing as well as in the performance and economic evaluation of converters based on solar photovoltaic systems of different technologies.

Construction project management and cost management is a difficult process that affects the overall success of construction projects. The success of a construction project can be assessed according to key performance indicators (KPIs). Cost savings and cost optimization over the life of a construction project is one of these KPIs. Cost management is largely performed through intelligent information technology in the construction industry. Information systems and information technologies have seen an increase in use in the management of construction projects. The same goes for cost management. Several studies mentioned in the paper point to this increase in use in recent years also in the management of costs at various stages. Many studies point to the use of information technology and software applications in the field of cost management. Still, to a large extent, there are no surveys focused on the analysis of the impact and impact factor of information technology on cost savings or cost optimization in various phases of construction projects. The research discusses the issue of the impact of information technology on cost management in various phases of a construction project. The main goal of the research is to analyze the influence of information technology factors on cost savings and optimization in individual phases of a construction project. Several statistical methods were used in the research. The resulting model of information technology impact factor was created based on data processing and the use of the AHP method.

(1) Background: Pedestrian injuries (PIs) represent a significant proportion of road traffic injuries. We aimed at investigating the incidence and mortality of PIs in different age groups and Socio-demographic Index (SDI) categories between 1990 and 2017. (2) Method: Estimates of age-standardized incidence and mortality along with trends of PIs by SDI levels were obtained from the Global Burden of Disease from 1990 to 2017. We also calculated forecasts until 2040. (3) Results: Globally, PIs incidence increased by 3.31% (–9.94 to 16.56) in 2017 compared to 1990. Men have a higher incidence of PIs than women. Forecasted incidence was 132.02 (127.37 to 136.66) per 100,000 population in 2020, 101.52 (65.99 to 137.05) in 2030 and reduced further to 71.02 (10.62 to 152.65) by 2040. Globally across all SDI categories, there was a decreasing trend in mortality due to PIs with the global estimated percentage reduction of 37.12% (–45.19 to –29.04). (4) Conclusions: The results show that PIs are still a burden for all SDI categories despite some variation. Although incidence and mortality are expected to decrease globally, some SDI categories may require particular attention in addition to specific vulnerable age groups. Further studies addressing incidence and mortality patterns in vulnerable SDI categories are needed.

This paper constructs a model of climate-related damage for small island developing states (SIDS). We focus on the loss of private productive capital stocks through extreme climate events. In contrast to most economic analyses of climate impacts, which assume temperature-dependent damage functions, we draw on the engineering literature to allow for a greater or lesser degree of anticipation of climate change when designing capital stocks and balancing current adaptation expenditure against future loss & damage. We apply the model to tropical storm damage in the small island developing state of Barbados and show how anticipatory behavior changes the damage to infrastructure for the same degree of climate change. Thus, in the model, damage depends on behavior as well as climate variables.

An appearance model plays a crucial rule in multi-target tracking. In traditional approaches, the two steps of appearance modeling i.e visual representation and statistically similarity measure are modeled separately. Visual representation is achieved either through hand-crafted features or deep features and statically similarity is measure through a cross entropy loss function. A loss function based on cross-entropy (KL-divergence, mutual information) find closely related probability distribution for the targets. However, if the targets have similar visual representation, it ends up mixing the targets. To tackle this problem, we come up with a synergetic appearance model named Single Shot Appearance Model based on Siamese neural network. The network is trained with a contrastive loss function for finding the similarity between different targets in a single shot. The input to the network is two target patches and based on their similarity, a contrastive score is output by the network. The proposed model is evaluated on accumulative dissimilarity metric on three datasets. Quantitatively, promising results are achieved against three baseline methods.

This paper presents a new methodology to derive and analyze strategies for a fully decarbonized urban transport system which combines conceptual vehicle design, a large-scale agent-based transport simulation, operational cost analysis, and life cycle assessment for a complete urban region. The holistic approach evaluates technical feasibility, system cost, energy demand, transportation time and sustainability-related impacts of various decarbonization strategies. In contrast to previous work, the consequences of a transformation to fully decarbonized transport system scenarios are quantified across all traffic segments, considering procurement, operation and disposal. The methodology can be applied to arbitrary regions and transport systems. Here, the metropolitan region of Berlin is chosen as a demonstration case. First results are shown for a complete conversion of all traffic segments from conventional propulsion technology to battery electric vehicles. The transition of private individual traffic is analyzed regarding technical feasibility, energy demand and environmental impact. Commercial goods, municipal traffic and public transport are analyzed with respect to system cost and environmental impacts. We can show a feasible transition path for all cases with substantially lower greenhouse gas emissions. Based on current technologies and today’s cost structures our simulation shows a moderate increase in total systems cost of 13-18%.

This is the first study to provide a systematic monetary benefit matrix, including greenhouse gas (GHG) emissions reduction benefits and air pollution reduction health co-benefits, for a change in on-the-road transport to low-carbon types. The benefit transfer method is employed to estimate the social cost of carbon and the health co-benefits via impact pathway analysis in Taiwan. Specifically, the total emissions reduction benefits from changing all internal combustion vehicles to either hybrid electric vehicles, plug-in hybrid electric vehicles, or electric vehicles would generate an average of US$760 million from GHG emissions reduction and US$2,091 million from health co-benefits based on air pollution reduction, for a total benefit of US$2,851 million annually. For a change from combustion scooters to light- or heavy-duty electric scooters, the average GHG emissions reduction benefits would be US$96.02 million, and the health co-benefits from air pollution reduction would be US$1,008.83 million, for total benefits of US$1,104.85 million annually.

In the last few decades, glaucoma became the second biggest leading cause of irreversible vision loss. Because of its asymptotic growth, it is not properly diagnosed until the relatively late stage. To stop the severe damage by glaucoma it is needed to detect glaucoma in its early stages. Surprisingly diabetes also be the greatest cause of glaucoma. In the modern era, artificial intelligence makes great progress in the medical image processing field. Image analysis based on machine learning gives a huge success in diagnosis glaucoma without any misdiagnosis. The aim of this proposed paper is to create an automated process that can detect glaucoma and diabetic retinopathy. Here various Machine Learning models are used and results of these methods are presented.

Seed viability is routinely measured on seeds that fail to germinate at the end of an experiment. Together with the number of germinants, this is used to estimate viability of the seeds at start of the experiment (i.e., initial viability) and provides the comparative basis on which germination success is determined. Perusal of the literature shows that sometimes (perhaps often, as the problem has yet to be recognized or reported) prolonged duration in the treatment, especially the control where little germination occurs, can lead to loss of viability. This results in underestimation of initial viability if that treatment is used. I caution against the routine use of end-of-trial germination and viability of ungerminated seeds as an estimate of initial viability in determining germination success of various treatments. I explore ways to deal with the problem but the preference is for estimates of initial viability to be undertaken on a separate sample of seeds concurrently with the experiment as this avoids the risk of seed death during the trial.

The power function distribution is a flexible waiting time model that may provide better fit for some failure data. This paper presents the comparison of the maximum likelihood estimates and the Bayes estimates of two-parameter power function distribution. The Bayes estimates are obtained, using conjugate priors, under five loss functions consist of square error, precautionary, weighted, LINEX and DeGroot loss function. The Gibbs sampling algorithm is proposed to generate samples from posterior distributions and in result the Bayes estimates are computed. The comparison of the maximum likelihood estimates and the Bayes estimates are done through the root mean squared errors. One real-life data set is analyzed to illustrate the evaluation of proposed methods of estimation. Finally, results from the simulation are discussed to assess the performance behavior of the maximum likelihood estimates and the Bayes estimates.

Construction projects are usually operating in a complex and dynamic environment in which the accumulation of many interrelated factors causes high uncertainty. Construction projects are complex and frequently involve substantial uncertainties including process complicatedness, intricate organization structure, dynamic environment, and financial strain. The study aims to categorize the influencing factors into three groups, namely construction project system, economic-market climate, and external environment. It attempts to adopt a novel analysis tool to examine the relationship between the project cost and multiple influencing factors by using Bayesian SEM. While the Bayesian SEM method has been receiving increasing attention in exploring the relationship between latent variables, construction studies still heavily rely on the covariance-based SEM approach. This study introduces several advantages of Bayesian SEM that make it more flexible and powerful than covariance-based SEM and provides the foundation of Bayesian SEM estimation and inference by illustrating this method in a project cost application.

Background: New open-source electric-grid planning models have the potential to improve power system planning and bring a wider range of stakeholders into the planning process for next-generation, high-renewable power systems. However, it has not yet been established whether open-source models perform similarly to the more established commercial models for power system analysis. This reduces their credibility and attractiveness to stakeholders, postponing the benefits they could offer. In this paper, we report the first model intercomparison between an open-source power system model and an established commercial production cost model. Results: We compare the open-source Switch 2.0 to GE Energy Consulting’s Multi Area Production Simulation (MAPS) for production-cost modeling, considering hourly operation under 17 scenarios of renewable energy adoption in Hawaii. We find that after configuring Switch with similar inputs to MAPS, the two models agree closely on hourly and annual production from all power sources. Comparing production gave a coefficient of determination of 0.996 across all energy sources and scenarios, indicating that the two models agree on 99.6% of the variation. For individual energy sources, the coefficient of determination was 69–100. Conclusions: Although some disagreement remains between the two models, this work indicates that Switch is a viable choice for renewable integration modeling, at least for the small power systems considered here. Although some disagreement remains between the two models, this work indicates that Switch is a viable choice for renewable integration modeling, at least for the small power systems considered here.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article's main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

Proteins are the main active molecules of Life. While natural proteins play many roles, as enzymes or antibodies for example, there is a need to go beyond the repertoire of natural proteins to produce engineered proteins that precisely meet application requirements, in terms of function, stability, activity or other protein capacities. Computational Protein Design aims at designing new proteins from first principles, using full-atom molecular models. However, the size and complexity of proteins require approximations to make them amenable to energetic optimization queries. These approximations make the design process less reliable and a provable optimal solution may fail. In practice, expensive libraries of solutions are therefore generated and tested. In this paper, we explore the idea of generating libraries of provably diverse low energy solutions by extending Cost Function Network algorithms with dedicated automaton-based diversity constraints on a large set of realistic full protein redesign problems. We observe that it is possible to generate provably diverse libraries in reasonable time and that the produced libraries do enhance the Native Sequence Recovery, a traditional measure of design methods reliability.

Keywords: Chemical Intolerance, Drug Intolerance, Food Intolerance, QEESI, BREESI, Multiple Chemical Sensitivity, Toxicant-induced Loss of Tolerance, Prevalence

During recent years UAVs have been increasingly used in agriculture and forestry research and application. Nevertheless, most of this work has been devoted to improving accuracy and explanatory power, often at the cost of usability and affordability. We tested a low-cost UAV and a simple workflow to apply four different greenness indices to the monitoring of pine (Pinus sylvestris and P. nigra) after-fire regeneration in a Mediterranean forest. We selected two sites and masured all pines within a pre-selected plot. Winter flights were carried out at each of the sites, at two flight altitudes (50 and 100 m). Automatically normalizing images entered an SfM based photogrammetric software for restitution and the obtained point cloud and orthomosaic processed to get a canopy height model and four different greenness indices. Sum of pine DBH was regressed on summary statistics of greenness indices and canopy height model. ExGI and GCC indices outperformed VARI and GRVI in estimating pine DBH, while canopy height model slightly improved the models. Flight altitude did not severely affect model performance. Our results show that low cost UAVs may improve forest monitoring after disturbance, even in those habitats and situations were resource limitation is an issue.

Intense physical efforts performed at maximal or near-maximal speeds and the ability to recover among sprint are important characteristics of soccer player. Considering that women's soccer is a markedly growing sport, the aim of the study was to analyse the performance (total time –TT-; fatigue index percentage -IF%) and physiological (aerobic and anaerobic) responses to Repeated Sprint Ability Test (RSA, 7×30 m sprints with 25 s of active recovery among sprints) in an elite female player (age: 30 yrs; BMI: 20.3 kg/m²). A repeated measure MANOVA over the 7 sprints time series was applied (p < 0.05). Results showed that TT was 58.71 s (Ideal Time: 56.98 s) with IF% of 3.0%. Energy contributions were given for 80.3% by aerobic, 19.2% by anaerobic lactid, and 0.5% by anaerobic alactid sources. Considering that 1) we have different kinetics in heart rate (HR) and maximum oxygen uptake with oxygen uptake that reach the peak when HR is still rising, and 2) the energy consumption during intermittent exercises requires different metabolism as a result of physiological stimuli proposed, the present findings substantiate the need to choose specific and adequate training methods for female soccer players that aim at increasing their RSA performances.

Background. Until now, cost of allergy treatment in insured public health care system and non-insured self-financing private health care system in Indonesia has not been well documented and published, as well as the cost of allergy treatment with subcutaneous immunotherapy. Objective. To evaluate the clinical and cost benefits of allergic rhinitis treatment in children with subcutaneous immunotherapy in non-insured self-financing private health care system. Methods. A retrospective cohort study conducted from 2015 until 2020, compared clinical improvement and health care costs over 18 months in newly diagnosed AR children who received SCIT versus matched AR control subjects who did not receive SCIT, with each group consisting of 1,098 subjects Results. Decrease of sp-HDM-IgE level (kU/ml) from 20.5 + 8.75 kU/ml to 12.1 + 3.07 kU/ml had been observed in the SCIT group. To reduce the symptom score of allergic rhinitis by 1.0 with SCIT it costs IDR 21,753,062.7 per child, for non SCIT it costs IDR 104,147,878.0 per child. Meanwhile, to reduce the medication score (MS) by 1.0 with SCIT it costs Rp. 17,024,138.8 while with non SCIT it costs Rp. 104,147,878.0. Meanwhile, to lower combination symptoms and medication score (CSMS) by 1.0, with SCIT it costs IDR 9,550,126.6, while with non SCIT it costs IDR 52,073,938.9. Conclusion. In conclusion, this first Indonesia-based study demonstrates substantial health care cost savings associated with SCIT for children with AR in an uninsured private health care system and provides strong evidence for the clinical benefits and cost-savings benefits of AR treatment in children.

River valley bottoms have hydrological, geomorphological, and ecological importance and are buffers for protecting the river from upland nutrient loading coming from agriculture and other sources. They are relatively flat, low-lying areas of the terrain that are adjacent to the river and bound by increasing slopes at the transition to the uplands. These areas have under natural conditions, a groundwater table close to the soil surface. The objective of this paper is to present a stepwise GIS approach for the delineation of river valley bottom within drainage basins and use it to perform a national delineation. We developed a tool that applies a concept called cost distance accumulation with spatial data inputs consisting a river network and slope derived from a digital elevation model. We then used wetlands adjacent to rivers as a guide finding the river valley bottom boundary from the cost distance accumulation. We present results from our tool for the whole country of Denmark carrying out a validation within three selected areas. The results reveal that the tool visually performs well and delineates both confined and unconfined river valleys within the same drainage basin. We use the most common forms of wetlands (meadow and marsh) in Denmark's river valleys known as Groundwater Dependent Ecosystems (GDE) to validate our river valley bottom delineated areas. Our delineation picks about half to two-thirds of these GDE. However, we expected this since farmers have reclaimed Denmark's low-lying areas during the last 200 years before the first map of GDE was created. Our tool can be used as a management tool, since it can delineate an area that has been the focus of management actions to protect waterways from upland nutrient pollution.

Legacy risks from infrastructures and industrial installations often reveal themselves when a potential for failure has been discovered much later than at the stage of the design and construction of a structure. In which case, there might already be a problem with the legacy installation, or even a crisis, without having had an accident. When the hazard cannot be taken away, the question arises as to how much effort, if any, should be spent on improving the situation. The usefulness of the three archetypical approaches to this problem: setting a standard, the As Low As Reasonably Practicable approach and a case-by-case discourse approach are discussed for their applicability for these legacy risks. Although it would be desirable to retrofit legacy risks to previously set legal requirements as is the case when acceptability limits are set in law or demonstration of ALARP is demanded, it may be impossible to reduce the residual risk to an otherwise acceptable level without taking away or replacing the infrastructure, which is not acceptable either. Therefor in conclusion the only available solution to persistent legacy risk problems seems to be to have a thorough discussion with all relevant stakeholders until an agreement is in some way found.

The lean supply chain of construction engineering projects is to achieve the maximum satisfaction of the owners' needs in order to effectively achieve the goal of supply chain management. This paper explores an effective method of lean supply chain cost management for construction engineering projects with target cost management, so that each participating unit on the supply chain node can fully utilizes its core competencies to minimize internal consumption and waste, and achieve the optimal overall efficiency of the supply chain. According to the requirements of the goal planning theory of the construction project company, establish a lean supply chain cost planning system for the construction project, realize the basic model of the lean supply chain cost management of the construction project, and set the target cost from the lean project of the construction project. The technical decomposition is established by the process of cost decomposition and cost pressure transmission and sub-target cost planning.

Drought stress is a major production constraint in crops globally. Crop wild relatives are important source of resistance and tolerance for both biotic and abiotic stresses, respectively. A breeding program was initiated to introgress drought tolerance in sunflower through hybridization between the wild species Helianthus argophyllus and the cultigen pool of H. annuus. Selection was carried out in the F2 to F5 segregating populations for high cuticular waxes, smaller leaf area, single heading and high oil content. The selected F5 breeding lines were compared with non-adapted elite sunflower germplasm in a replicated randomized complete block research project using different water treatments comparing fully irrigated (T0), with 75 (T1), 50 (T2) and 25% (T3) irrigation treatments. The comparison between the two types of germplasm showed that drought tolerant breeding lines had comparatively lesser decreases in leaf area, shoot weight and root shoot ratio 10 under the various drought treatments. Leaf area of the drought selected F5 lines were smaller than that of the elite germplasm under controlled irrigated treatments, but they maintained their leaf area under the drought treatments. Several drought resistant promising lines D-2, D-5, and D-27 were identified and showed high leaf area, great root length and increase root to shoot ratio under the highest stressed treatments (T3). Some of the lines could be directly used for the development of drought tolerant hybrids. Combining ability test indicated D-27 (F7) as good general combiner for seed yield plant−1 and oil contents when mated with male line RSIN.82. These hybrids could help to minimize seed yield losses due to water stress and to achieve profitable cultivation of sunflower in 18 arid regions of Pakistan.

This paper analyses and evaluate the precision and the accuracy the capability of low-cost terrestrial photogrammetry by using many digital cameras to construct a 3D model of an object. To obtain the goal, a building façade has imaged by two inexpensive digital cameras such as Canon and Pentax camera. Bundle adjustment and image processing calculated by using Agisoft PhotScan software. Several factors will be included during this study, different cameras, and control points. Many photogrammetric point clouds will be generated. Their accuracy will be compared with some natural control points which collected by the laser total station of the same building. The cloud to cloud distance will be computed for different comparison 3D models to investigate different variables. The practical field experiment showed a spatial positioning reported by the investigated technique was between 2-4cm in the 3D coordinates of a façade. This accuracy is optimistic since the captured images were processed without any control points.

Fresh water springs are unique natural resources in Florida, currently under threat from increasing groundwater pumping and pollution resulting from a variety of sources. This paper estimates current recreation benefits from visiting springs using the travel cost method and elicits residents’ willingness to contribute for springs restoration using the contingent valuation method. It further compares the performance of count data models correcting for endogenous stratification and truncation, and finds that the annual consumer surplus per person per trip is between $20 and $43. Furthermore, visitors are willing to contribute $12 to $14 per person per trip for springs restoration without reducing trip demand.

In this letter, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows obtaining micro resolution channels at powers between 2 and 10mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

Using the PLCC advantages generates revenue and lowers costs more than might be anticipated. It ensures better decisions by using a more perfect and practical assessment of revenues and costs. Although the supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology company; this cloud make company decision–makers focus on low PLCC and select better supplier.

Late pear cultivars, such as ‘Conference’, can be stored for a long period, with their storability depending on storage conditions. A three-year study (2011-2013) compared the impact of half-year storage using four technologies – normal atmosphere, normal atmosphere + 1-methylcyclopropene (1-MCP), controlled atmosphere, controlled atmosphere + 1-MCP – on the quality parameters of ‘Conference’ pears, such as mass loss, firmness, total soluble solids, acidity, antioxidant capacity, and the incidence of diseases and disorders. Additionally, the study analysed different storage conditions in terms of profitability, based on the market prices for pears in the seasons during which the pears were stored. The storage conditions had a very strong influence on the fruit quality parameters, and was found to affect most visibly the mass loss and the incidence of postharvest diseases and disorders. The storage of ‘Conference’ pears for 180 days in normal atmosphere is not economically viable, even if the fruit is subjected to 1-MCP treatment.

Already more than 140 countries consider or have pledged to reach net-zero emission targets by 2050 or earlier and the share of global emissions falling into an emission pricing scheme has steeply increased over the past three years. Even where there are no direct implications for industry (yet), there is a series of subtle pressure points driving an increasing number of companies across the globe to work towards climate neutrality and pledging ambitious emission reduction goals. This article sheds light on the pressure points, the subtle triggers, the underlying considerations as well as the hoped-for benefits for industrial companies from achieving net-zero emissions. The observations and ideas presented in this paper are derived from quantitative data obtained via the Energy Efficiency Index of German Industry (EEI) and qualitative data. Not only societal, work force, supply chain and investor expectations play a large role, but also many strategic considerations which have the potential to make the company more resilient and profitable, particularly in time of crisis. Those companies that do not move towards decarbonisation, on the other hand, may face a costly late-mover disadvantage. This piece uncovers subtle interconnections, helping stakeholders from industry and beyond to grasp opportunities and challenges ahead.

Rapeseed (Brassica napus) is one of the most important oil crops in the world; however, drought significantly curtails its growth and productivity. Identifying drought-tolerant germplasm is an efficient and low-cost strategy for addressing water shortages. Using water loss ratio (WLR) as an index of drought tolerance, we screened a panel of 265 B. napus lines. We identified eight low-WLR and six high-WLR accessions, which were regarded as drought-tolerant and drought-sensitive, respectively. Further validated these selected accessions at the seedling stage under drought-stress conditions. The drought-tolerant accessions had significantly greater fresh and dry weights under drought stress than the drought sensitive accessions. Using RT-qPCR, we showed that a set of previously reported drought-adaptive marker genes were expressed at higher levels in the drought-tolerant lines than in the drought-sensitive lines. These results indicated that the drought-tolerant genotypes could be identified from natural populations using WLR. Then, we performed a genome-wide association study to identify loci harboring single nucleotide polymorphisms (SNPs). A total of 139 SNPs were significantly associated with the WLR, of which chromosome A10 harbored the largest number. Furthermore, four putative candidate genes were selected by combining the SNP–WLR association results and transcriptional expression data with the changes in drought tolerance. Thus, we have identified two drought-tolerant B. napus cultivars and uncovered genome-wide variation differentiating B. napus lines related to WLR, in addition to providing insights for further research into WLR-related drought mechanisms.

The concept of geostationary VHTS (Very High Throughput Satellites) is based on multibeam coverage with intensive frequency and polarization reuse in addition to the use of larger bandwidths in the feeder links, in order to provide high capacity satellite links at a reduced cost per Gbps in orbit. The dimensioning and design of satellite networks based on VHTS imposes the analysis of multiple trade-offs to achieve an optimal solution in terms of cost, capacity and figure of merit of the user terminal. In this paper, we propose a new method for sizing VHTS satellite networks based on an analytical expression of the forward link CINR (Carrier-to-Interference-plus-Noise Ratio) that is used to evaluate the trade-off of different combinations of system parameters. The proposed method considers both technical and commercial requirements as inputs including the constraints to achieve the optimum solution in terms of the user G/T, the number of beams and the system cost. The cost model includes both satellite and ground segments. Exemplary results are presented with feeder links using Q/V bands, DVB-S2X and transmission methods based on CCM and VCM (Constant and Variable Coding and Modulation, respectively) in two scenarios with different service areas.

Low-cost particle sensors are now used worldwide to monitor outdoor air quality. However, they have only been in wide use for a few years. Are they reliable? Does their performance deteriorate over time? Are the algorithms for calculating PM2.5 provided by the Plantower company for PurpleAir monitors accurate? We investigate these questions using continuous measurements of four monitors (8 sensors) under normal conditions inside and outside a home for 1.5-3 years. A recently-developed algorithm (called ALT-CF3) is compared to the two existing Plantower algorithms. The Plantower CF1 algorithm was shown to lose 25-50% of all indoor data due to the questionable practice of assigning zero to all concentrations below a threshold. None of these data were lost using the ALT-CF3 algorithm. About 92% of all data showed precision better than 20% using the ALT-CF3 algorithm, but only about 45-75% of data achieved that level using the Plantower CF1 algorithm. The limits of detection (LODs) using the ALT-CF3 algorithm were mostly under 1 ug/m3, compared to about 3-10 ug/m3 using the Plantower CF1 algorithm. The percent of observations exceeding the LOD was 53-92% for the ALT-CF3 algorithm, but only 16-44% for the Plantower CF1 algorithm. For indoor air in homes, the Plantower algorithms are inappropriate.

Although it is known that the gut microbiota (GM) can be modulated by diet, the efficacy of specific dietary interventions in determining its composition and diversity in obese patients remains to be ascertained. The present work aims to evaluate the impact of a moderately hypocaloric Mediterranean diet on the GM of obese and overweight patients (OB). The GM of 23 OB patients (F/M= 20/3) was compared before (T0) and after 3 months (T3) of the nutritional intervention (NI). Fecal samples were analyzed by Illumina MiSeq sequencing of the 16S rRNA gene. At baseline, the GM characterization confirmed the typical obesity-associated dysbiosis. After 3 months of NI, patients presented a statistically significant reduction of the body weight and fat mass, along with changes in the relative abundance of many microbial patterns. In fact, we observed an increased abundance in several Bacteroidetes taxa (i.e. Sphingobacteriaceae, Sphingobacterium, Bacteroides spp., Prevotella stercorea) and depletion of many Firmicutes taxa (i.e. Lachnospiraceae members, Ruminococcaceae and Ruminococcus, Veillonellaceae, Catenibacterium, Megamonas). In addition, the phylum Proteobacteria showed an increased abundance, while the genus Sutterella, within the same phylum, decreased after the intervention. Metabolic pathways, predicted by bioinformatic analyses, showed a decrease in membrane transport and cell motility after NI. The present study extends our knowledge of the GM profiles in OB, highlighting the potential benefit of a moderate caloric restriction in counteracting the gut dysbiosis.

This paper considers estimating the ratio of two distributions with different parameters and common supports. We consider a Bayesian approach based on the Log--Huber loss function which is resistant to outliers and useful to find robust M-estimators. We propose two different types of Bayesian density ratio estimators and compare their performance in terms of Bayesian risk function with themselves as well as the usual plug-in density ratio estimators. Some applications such as classification and divergence function estimation are addressed.

The goal of this paper is to present a low-cost, low-power prototype of a pulsed Ultra Wide Band UWB) oscillator and an UWB elliptical dipole antenna integrated on the same Radio Frequency (RF) Printed Circuit Board (PCB) and its digital control board for Real Time Locating System (RTLS) applications. The design is compatible with IEEE 802.15.4 high rate pulse repetition UWB standard being able to work between 6 GHz and 8.5 GHz with 500 MHz bandwidth and with a pulse duration of 2 ns. The UWB system has been designed using the CST Microwave Studio transient Electro-Magnetic (EM) circuit co-simulation method. This method integrates the functional circuit simulation together with the full wave (EM) simulation of the PCB’s 3D model allowing fast parameter tuning. The PCB has been manufactured and the entire system has been assembled and measured. Simulated and measured results are in excellent agreement with respect to the radiation performances as well as the power consumptions.

The importance of this study may be defined by using the smart techniques to earned value indicators of residential buildings projects in Republic of Iraq, only one development intelligent forecasting model was presented to predict Schedule Performance Index (SPI), Cost Performance Index (CPI), and To Complete Cost Performance Indicator (TCPI) are defined as the dependent. The approach is principally influenced by the determining numerous factors which effect on the earned value management, that involves Iraqi historical data. In addition, six independent variables (F1: BAC, Budget at Completion., F2: AC, Actual Cost., F3, A%, Actual Percentage., F4: EV, Earned Value. F5: P%, Planning Percentage., and F6: PV, Planning Value) were arbitrarily designated and satisfactorily described for per construction project. It was found that ANN has the capability to envisage the dust storm with a great accuracy. The correlation coefficient (R) has been 90.00%, and typical accuracy percentage has been 89.00%.

The osteoarthritis (OA), the main cause of disability, is a chronic condition that most frequently affects older adults. As the population ages, the cost of treatment is placing pressure on the healthcare budget. As a result, it is imperative to evaluate the medicines' cost-effectiveness and the influence they have on health resource allocation. Hence, our study aims to summarize the cost and outcome of utilizing glucosamine in OA treatment. Authentic databases like Medline, Cochrane, and Scopus were adopted for the identification process up until July 2023. Our primary inclusion criteria centered on the economic evaluation of Glucosamine in OA treatments with provided the incremental cost-effectiveness ratio (ICER) at least. The Quality of Health Economic Studies (QHES) instrument was applied to grade the quality of the studies. A total of 7 qualified studies were selected and discussed the cost-effectiveness of glucosamine with or without other formulations. All of them demonstrated that glucosamine was cost-effective. There was an in-creasement of QALY when incorporating Glucosamine into conventional care. Moreover, Crystalline Glucosamine Sulfate (pCGS) was more cost-effective than the Other Formulations of Glucosamine (OFG). In overall, utilizing pCGS was more beneficial than OFG in terms both of cost and quality of life.

Primary and secondary cardiovascular prevention is less effective than expected due to the concern about polymedication by professionals and the lack of patient adherence to medications prescribed in the medium and long term. Polypills have been presented as a possible solution. A comprehensive bibliographic review is presented about polypills as mechanisms for facilitating adherence and a proposed guide for the use of polypills for the prevention of cardiovascular risk. 41 articles were included, showing options for the polypill as a method of primary and secondary cardiovascular prevention.The polypill increases therapeutic adherence in the medium and long term, also increasing the therapeutic results compared to the administration of the various drugs separately. Based on the evidence, a flow diagram is proposed for the prescription of a polypill.Polypills increase the effectiveness and adherence of patients to primary and secondary cardiovascular prevention programs, without increasing the cost of the intervention. The use of a polypill in cardiovascular prevention can be effective as a prescription tool.

Supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology company; this cloud makes company decision–makers focus on low PLCC and select a better supplier in sustainable supply chains goal.

It is widely believed that the dramatic transformation of the spherical outflows of AGB stars into the extreme aspherical geometries seen during the planetary nebula (PN) phase is linked to binarity and driven by the associated production of fast jets and central disks/torii. The key to understanding the engines that produce these jets and the jet-shaping mechanisms lies in the study of objects in transition between the AGB and PN phases. I discuss the results of our recent studies with high-angular-resolution (with ALMA & HST) and at high-energies (with GALEX, XMM-Newton & Chandra) of several such objects, which reveal new details of close binary interactions and high-speed outflows. These include two PPNe (the Boomerang Nebula and IRAS16342-3814), and the late carbon star, V Hya. The Boomerang is notable for a massive, high-speed outflow that has cooled below the microwave background temperature, making it the coldest object in the Universe. IRAS16342 is the prime example of the class of water-fountain PPNe (very young PPNe with high-velocity H₂O masers) and shows the signature of a precessing jet. V Hya ejects high-speed bullets every 8.5 years associated with the periastron passage of a companion in an eccentric orbit. I discuss our work on AGB stars with strongly-variable high-energy (FUV, X-ray) emission, suggesting that these objects are in the early stages of binary interactions that result in the formation of accretion disks and jets.

Congestion pricing has received lots of attention in the scientific discussion. Congestion pricing means that the operator increases prices at the time of congestion and the traffic demand is expected to decrease. In a certain sense, shadow prices are an optimal way of congestion pricing: users are charged shadow prices, i.e., the expectations of future losses because of blocked connections. The shadow prices can be calculated exactly from Howard’s equation, but this method is difficult. The paper presents simple approximations to the solution of Howard’s equation and a way to derive more exact approximations. If users do not react by lowering their demand, they will receive higher bills to pay. Many users do not react to increased prices but would want to know how the congestion pricing mechanism affects the bills. The distribution of the price of a connection follows from knowing the shadow prices and the probability of a congestion state. There is another interesting distribution. The network produces profit to the operator, or equivalently, blocked connections produce a cost to the operator. The average cost rate can be calculated from Howard’s equation, but the costs have some distribution. The distribution gives the risk that the actual costs exceed the average costs, and the operator should include this risk to the prices. The main result of this paper shows how to calculate the distribution of the costs in the future for congestion pricing by shadow prices and for congestion pricing with a more simple pricing scheme that produces the same average costs.

This systematic review investigates the failure rate and marginal bone loss (MBL) of dental implants placed in Solid-organ transplant (SOT) patients compared to healthy controls. Three databases (PubMed, Web of Sciences and the Cochrane Library) were searched up to June 2020 (PROSPERO CRD42019124896). Case-control and cohort studies reporting data failure rate and marginal bone loss (MBL) of dental implants placed in SOT patients were included. The risk of bias of observational studies was assessed through the Newcastle-Ottawa Scale (NOS). Four case-control studies fulfilled the inclusion criteria, all of low risk of bias. Meta-analyses revealed consistently lower implant failure rate than control populations at patient and implant levels. SOT patients had a significant difference of -18% (p-value <0.001) of MLB towards healthy patients. SOT status poses no serious threat to implant survival. Overall, this group of patients presented lower levels of dental implant failure rate and marginal bone loss compared to otherwise healthy patients. Further intervention trials with wider sample size and longer follow-ups are necessary to confirm these summary results.

This paper focuses on the non-destructive dielectric measurement for low-loss planar materials with a thickness of less than 3 mm using a large coaxial probe with an outer diameter of 48 mm. The aperture probe calibration procedure required only to make a measurement of the half-space air and three offset shorts. The reflection coefficient for the thin material is measured using a Keysight E5071C network analyzer from 0.3 MHz to 650 MHz and then converted to a relative dielectric constant and tangent loss via closed form capacitance model and lift-off calibration process. Measurement error of dielectric constant, Δε_r is less than 2.5 % from 1 MHz to 400 MHz and the resolution of loss tangent, tan δ measurement is capable of achieving 3×10^-3.

OBJETIVES: During the COVID-19 pandemic, the risk of collapse of the health system created great difficulties. We will demonstrate that Intermediate Respiratory Care Units (IRCU) provide adequate management of patients with non-invasive respiratory support, which is particularly important in patients with SARS-CoV-2 pneumonia. METHODS: A prospective observational study of patients with COVID-19 admitted to the ICU of a tertiary hospital. Sociodemographic data, comorbidities, pharmacological, respiratory support, laboratory and blood gas variables were collected. The overall cost of the unit was subsequently analyzed. RESULTS: 991 patients were admitted, 56 to the IRCU (of the 81 a critical care unit). Mean age was 65 years (SD 12.8), Barthel Index 75 (SD 8.3), Charlson 3.1 (SD 2.2), HTN 27%, COPD 89% and obesity 24%. Significant relationship (p <0.05) with higher mortality of the following: fever greater than or equal to 39oC [OR 5.6; 95% CI (1.2-2.7); p = 0.020], protocolized pharmacological treatment [OR 0.3; 95% CI (0.1-0.9); p = 0.023] and IOI [OR 3.7; 95% CI (1.1-12.3); p = 0.025]. NIMV showed less of a negative impact [OR 1.8; 95% CI (0.4-8.4); p = 0.423] than IOI. The total cost of the IRCUs amounted to €66,233. The cost per day of stay in the IRCU was €164 per patient. The total cost avoided was €214,865. CONCLUSION: The pandemic has highlighted the importance of IRCUs in facilitating the management of a high patient volume. The treatment carried out in IRCUs is effective and efficient, reducing both admissions to and stays in the ICU.

Air quality and environmental fairness have always been an area of prime interest across the globe. The significance low-cost air quality sensing and practices spikes during the time of pan-demic and epidemics when the air becomes a threat to living beings especially human beings. The gradual innovation and enrichment in low-cost air quality sensing sensors, nodes or devices, and systems are exponentially increasing for the last three decades. This work reviews the major contributions in a) low-cost scalable air quality assessment; b) low-cost air quality sensors, sensing approaches and technologies; c) low-cost state-of-the-art gas sensors fabrication methods (MEMS and CMOS); d) low-cost gas sensors measurement configurations and assemblies; and e) low-cost air quality sensors calibration and testing systems. A systematic review of past work with a goal to assist end-users, public health facilities, state agencies, researchers, scientists and air quality protection agencies has been rendered in this work. Starting from sensors electrodes to IoT based mobile smart nodes; all have been introduced in this article.

Buildings use 30-40 % of all energy resources and are thus their main consumers in modern society. Moreover, buildings require a vast amount of different raw materials. During the last two decades, several green building certifications have been created in order to consider social, economic and environmental aspects of sustainability of buildings. One of the most famous and widely used of these certifications is Leadership in Energy and Environmental Design (LEED). So far, the use of LEED has concentrated in the US and other developed countries. One reason that restricts the use of this point-based system certification in developing countries is the limited data about its costs. In this study, the extra cost of the certification process will be evaluated besides the changes needed in the design of the building to reach the points required by LEED. At the first stage, the number of points the case study earns in its current format (Scenario 1) were found out, then the cost difference of getting either the Certified (Scenario 2) or Silver (Scenario 3) level LEED certification for the building was studied. It was found that besides some technical considerations, filling the criteria of the Certified and Silver level increases the total costs of construction by 3.4% and 5.9%. Further improvement of the building’s energy efficiency would enable the attainment of a higher-level certification. The results of the study could help to promote the use of green building certifications in Western Asia.

The black hole information paradox is one of the most puzzling paradoxes in physics. Black holes trap everything that falls into them, while their mass may leak away through purely thermal Hawking radiation. When a black hole vanishes, all the information locked inside, if any, is just lost, thus challenging the principles of quantum mechanics. However, some information does have a way to escape from inside the black hole, that is, through gravitational waves. Here, a concise extension of this notion is introduced. When a black hole swallows something, whether it is a smaller black hole or an atom, the system emits gravitational waves carrying the information about the “food”. Although most of the signals are too weak to be detected, the information encoded within them will persist in the universe. This speculation provides an explanation for a large part, if not all, of the supposed “information loss” in black holes, and thus reconciles the predictions of general relativity and quantum mechanics.

This article presents a unique set of voltage and current data from a public building and acquired using a hybrid measurement solution that combines Python and Grafana. The transversal purpose consists of contributing to the community with a vision of the quality of the supply more oriented to the monitoring of the state of the network, providing a more realistic vision, which allows a better understanding, and the adoption of the best decisions to achieve the efficient energy management and thus optimize the operation and maintenance of power systems. The work focuses on higher order statistical estimators that, combined with exploratory data analysis techniques, improve the characterization of the shape of the stress signal. These techniques and data, together with the acquisition and monitoring system, present a unique combination in the line of low-cost measurement solutions. It also incorporates the underlying benefit of the contribution to industrial benchmarking. The paper also includes a computational comparison between Python and LabVIEW to elicit the performance of the measurement solution.

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

The corrosion of prestressing steel in prestressed concrete bridges is a critical issue for bridge maintenance. To assess structures with corroded strands, it is necessary to define the mechanical properties of the strands and their influence on the structural behavior. In this study, corroded strands are taken from external tendons in existing bridges and tested to define the effects of corrosion on the tensile properties of the strand. Empirical equations for the tensile strength and ductility of the corroded strand are proposed using test results. The most corroded wire governs the mechanical properties of the strand. Experiments on prestressed concrete beams with a single corroded strand are conducted to investigate the structural behavior. A reduction in the flexural strength and maximum deformation is observed from the experiment. According to the section loss of a wire in a strand and its location in a beam, the flexural capacity can be evaluated using the proposed equation. The reduced ultimate strain of the corroded strand can be the governing factor of the flexural strength.

Background: We aimed to assess the association between DII and PD and the mediation effect of DII in the association of PD with systemic inflammation. Using the National Health and Nutrition Examination Survey (NHANES) 2009-2010, 2011-2012 and 2013-2014, participants that received periodontal exam and provided dietary recall data were included. The inflammatory potential of diet was calculated via DII. Periodontitis was defined according to the 2012 case definition. The clinical outcomes of interest were mean periodontal probing (PPD), mean clinical attachment loss (CAL) and thresholds of PPD and CAL. White blood cells (WBC), segmented neutrophils and C-reactive protein (CRP) were used as proxies for systemic inflammation. The periodontal measures were regressed across DII values using adjusted multivariate linear regression. Adjusted mediation analysis appraised the influence of DII in the association of periodontitis and systemic inflammation. 10,178 participants were included. DII was significantly correlated with mean PPD, mean CAL, thresholds of PPD and CAL, WBC, segmented neutrophils and DII (p&lt;0.01). A linear regression logistic adjusted for multiple confounding variables confirmed the association between DII and mean PPD (B = 0.02, Standard Error [SE]: 0.02, p&lt;0.001) and CAL (B = -0.02, SE: 0.01, p&lt;0.001). The association of mean PPD and mean CAL with both white blood cells and segmented neutrophils were mediated by DII (from 2.1 to 3.5%, p&lt;0.001). In the 2009-2010 subset, the association of mean CAL with serum CRP was mediated by DII (52.0%, p&lt;0.01). In conclusion, inflammatory diet and PD may be associated. Also, the inflammatory diet significantly mediated the association of leukocyte counts and systemic inflammation with periodontitis.

With the development of energy internet, integrated energy system can effectively reduce carbon emissions and improve the utilization of renewable energy. In this paper, a low-carbon optimal scheduling model of integrated energy system considering heat loss of heat network pipeline is proposed. Based on the study of concentrating solar power (CSP) plant and heat storage tank (HS), an optimal scheduling model is established, which takes system operation cost, environmental pollution and penalty cost of abandoning wind and solar energy as objectives. Through the analysis of example results, it is proved that the model proposed in this paper can achieve the goal of reliable, low-carbon and economic operation of the system. At the same time, it shows that CSP unit can reduce the operation cost of system and increase energy coupling and utilization.

Meniere Disease (MD) is a multifactorial disorder of the inner ear characterized by vertigo attacks associated with sensorineural hearing loss and tinnitus with a significant heritability. Although MD has been associated with several genes, no epigenetic studies have been performed in MD. Here we performed whole genome bisulfite sequencing in 14 MD patients and 6 healthy controls, with the aim of identifying a MD methylation signature and potential disease mechanisms. We observed a high number of differentially methylated CpGs (DMC) when comparing MD patients to controls (N= 9,545), several of them in hearing loss genes such as PCDH15, ADGRV1 and CDH23. Bioinformatic analyses of DMCs and cis-regulatory regions predicted phenotypes related to abnormal excitatory postsynaptic currents, abnormal NMDA-mediated receptor currents and abnormal glutamate-mediated receptor currents when comparing MD to controls. Moreover, we identified various DMCs in genes previously associated with cochleovestibular phenotypes in mice. We have also found 12 undermethylated regions (UMR) that were exclusive to MD, including 2 UMR in an inter CpG island in the PHB gene. We suggest that the DNA methylation signature allows to distinguish between MD patients and controls. The enrichment analysis confirms previous findings of a chronic inflammatory process underlying MD.

Aims: The objective of this study was to assess the cost-effectiveness of the CardioMEMS HF system in a HF Clinic in Spain by evaluating the real-time remote monitoring of pulmonary artery pressures, which has shown to reduce heart failure (HF) related hospitalizations and improve the quality of life for selected HF patients. Particularly, the study aimed to determine the value of CardioMEMS in Southern Europe, where healthcare costs are significantly lower and its effectiveness remains uncertain. Methods: This single-centre study enrolled all consecutive HF patients who had been implanted with a pulmonary artery pressure sensor (CardioMEMS-HF system, Abbott Laboratories, Abbott Park, IL, USA). The number of HF hospitalizations in the year before and the year after the sensor implantation was compared and quality-adjusted life years (QALY) gained based on a literature review of previous studies was calculated. Results: The rate of HF hospitalisations was significantly lower at 1 year compared with the year before CardioMEMS implantation (0.25 versus 1.10 events/patient-years, HR 0.22, p=0.001). At the end of first year, the usual management outperformed the CardioMEMS HF system, resulting in a net monetary value difference of 2,540€ per patient and a benefit-cost ratio of 0.38. However, by the end of the second year, the CardioMEMS system is estimated to reduce costs compared to usual management. Conclusions: Based on the results, we suggest that remote monitoring of pulmonary artery pressure with the CardioMEMS HF system represents a long-term cost-effective strategy in a healthcare setting in Southern Europe.

Foveal vision loss has been shown to reduce efficient visual search guidance due to contextual cueing by incidentally learned contexts. However, previous studies used artificial (T among L-shape) search paradigms that prevent the memorization of a target in a semantically meaningful scene. Here, we investigated contextual cueing in real-life scenes that allow explicit memory of target locations in semantically rich scenes. In contrast to the contextual cueing deficits in artificial scenes, contextual cueing in patients with age-related macular degeneration (AMD) did not differ from age-matched normal-sighted controls. We discuss this in the context of visuospatial working memory demands for which both eye-movement control in the presence of central vision loss and for memory-guided search may compete. Memory-guided search in semantically rich scenes may depend less on visuospatial working memory than search in abstract displays, potentially explaining intact contextual cueing in the former but not the latter. In a practical sense, our findings may indicate that Patients with AMD are less deficient than expected after previous lab experiments. This shows the usefulness of realistic stimuli in experimental clinical research.

Denture wearers often complain about jeopardized function and reduced quality of life due to lack of prosthesis’ retention. Implant retained mandibular overdentures, on 2 non-connected implants (2IOD) are well-proven solutions to overcome these issues. We prospectively assessed 69 patients and scrutinized clinical records until at least 7 years of function. Thirty-six were retained on Locator ® Abutments (LA) and thirty-tree on Ball Abutments (BA). Both systems were compared regarding the type, amount and total cost of required maintenance. One implants was lost, yielding 98.7% survival after 7 years. In total 438 technical issues occurred: 121 (27.35%) in BA and 317 (72.4%) in LA. Out of these, 343 events (78%) were solved chairside: 191 (43.6%) were replacements of retention caps, 113 (25.8%) were minor acrylic repairs, in 26 (5.9%) pressure ulcers had to be relieved and 13 (3%) related to abutments. LA required 179 insert replacements compared to 12 in the BA group. The overall initial treatment cost was 3850 euro. The average total maintenance cost in relation to the initial cost for the LA and BA groups was 19.11% (range 0% - 82.24%) and 18.91% (range 0% - 113.26%) respectively (P=0.540). Conclusions: The 7-years maintenance costs for a 2IOD is acceptable when the patient is regularly checked and professionally maintained. Most events are easily solvable chairside, but a few patients required more expensive interventions, regardless of the type of attachment used.

Wet anaerobic storage of algal biomass is a promising preservation approach which can ensure continuous supply of these feedstocks to biorefineries year-round. An effective solution to preservation must ensure minimal dry matter loss and change in biochemical composition during storage. Therefore, the objective of this study was to investigate the preservation of Nannochloropsis gaditana biomass through wet anaerobic storage and its impact on biomass quality. Prior to storage, algae sample was inoculated with two different strains of lactic acid bacteria and thereafter stored for 30 and 180 days. Each inoculant limited dry matter loss to &lt;10% (dry basis) after the storage durations. Final pH values (4.3 - 4.8) indicate that the biomass samples were properly ensiled, achieving the acidic conditions necessary for preservation. Compositional analysis of the biomass after storage showed a reduction in carbohydrate content, a relative increase in lipid content, and no significant change to the protein fraction. Glucose and galactose were the prevalent sugar monomers. The low dry matter loss and minimal compositional change indicates that wet anaerobic storage is an effective means of preserving algal biomass, ensuring a constant supply of algal biomass feedstock to a biorefinery.

Aero-fuel centrifugal pumps are important power plants in aero-engines. Unlike most of the existing centrifugal pumps, a combination impeller is integrated with the pump to improve its performance. First, the critical geometrical parameters of combination impeller and volute are given. Then, the effects of combination impeller on flow characteristics inside the impeller and volute are clarified by comparing simulation results with that of the conventional impeller, where the effectiveness of selected numerical method is validated by an acceptable agreement between simulation and experiment. Finally, the experiment is performed to test the external performance of studied pump. A significant feature of this study is that the flow characteristics are significantly ameliorated by reducing the flow losses emerged in impeller inlet, impeller outlet and volute tongue. Correspondingly, the head and efficiency of combination impeller are higher with comparison to conventional impeller. Consequently, it is a promising approach in ameliorating flow field and improving external performance by applying a combination impeller to an aero-fuel centrifugal pump.

Cement manufacturing is one of the most energy-intensive industries in the world. Most of the cost of producing cement is accounted by fuel consumption and power expenditures. Thermal power plants are the major source of electricity in Pakistan. But they are not efficient and environmentally friendly. This study simulates four different models for five cement plants of Pakistan on Homer Pro software and compares the optimal solutions based on the net present cost (NPC), levelized cost of electricity (LCOE) and greenhouse gas (GHG) emissions. Model-1 consists of solar panels, electrolyzer, hydrogen tank, hydrogen generator and converter. Model-2 has only a diesel generator and acts as a base case in this study. Model-3 has solar panels and a battery-converter system. In Model-4, diesel generators, solar panels and converters are considered. Based on NPC, the most optimal model is Model-4, having a 0.249 $/KWh LCOE in islanded systems. The NPC and operating costs are US$540 million and US$ 32.5 million per year, respectively, with a 29.80% reduction in CO2 emissions when compared to the base case. Based on GHG emissions, Model-1 and Model-3 are the best models with 0% GHG emissions. Sensitivity analyses is also performed using the parameters of load, inflation rate and discounted rate. The results prove that the proposed hybrid micropower systems (HMS) can sustainably provide electricity for 24 hours a day to the sites under consideration with minimum objectives.

Age-related hearing loss (ARHL) is the most common sensory disorder in the elderly. It is associated with aging and hair cell death due to oxidative stress-induced mitochondrial dysfunction. Although transgenic mice and long-term cultures for induction of aging have been used to study ARHL, there are presently no ARHL animal models stimulated by intermittent environmental change for aging. In this study, an ARHL animal model was established by inducing continuous oxidative stress to promote short-term aging of cells, determined based on the expression of the hearing loss-induced phenotype and aging related factors in the short term. The incidence of hearing loss was significantly different among the groups subjected to intermittent hypoxic environment, high-fat diet (HFD), and injection with D-galactose. Continuous oxidative stress and HFD were factors that accelerated cellular aging. Increase in UCP2 affected oxidative stress and mitochondrial dysfunction. CDH23, SLC26A4, KCNQ4, Myo7a, and Myo6, which are ARHL-related factors, were modified by oxidative stress in cells of the hearing organ. We found that intermittent hypoxic, HFD, and galactose injection accelerated cellular aging in the short term. Thus, we anticipate that the development of this hearing loss animal model, which reflects intermittent environmental changes, will benefit future research on ARHL.

Supplier selection (SC) continues to be a crucial component in manufacturing procurement. Using the PLCC advantages generates revenue and lowers costs more than might be anticipated. Supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. Past literature on this topic is limited. We try to close this gap in knowledge. In this study, we attempt to apply two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we are comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology Company; this cloud makes company decision–makers focus on low PLCC and select a better supplier in sustainable supply chains development.

Background: Vitamin D was studied in regards to its possible impact on body mass reduction and metabolic changes in adults and children with obesity yet there were no studies assessing the impact of vitamin D supplementation during a weight management programme in children and adolescence. The aim of our study was to assess the influence of 26 weeks of vitamin D supplementation in overweight and obese children undergoing an integrated 12-months’ long weight loss programme on body mass reduction, body composition and bone mineral density. Methods: A double-blind randomized placebo-controlled trial. Vitamin D deficient patients ( <30 ng/ml level of vitamin D) aged 6-14, participating in multidisciplinary weight management programme were randomly allocated to receiving vitamin D (1200 IU) or placebo for the first 26 weeks of the intervention. Results: Out of the 152 qualified patients, 109 (72%) completed a full cycle of four visits scheduled in the programme. There were no difference in the level of BMI change. Although the reduction was greater in the vitamin D vs. placebo group (-4.28 ± 8.43 vs. -2.53 ±6.10) the difference was not statistically significant (p=0.319). Similarly the reduction in fat mass – assessed both using bioimpedance and DEXa was achieved, yet the differences between the groups were not statistically significant. Conclusions: Our study ads substantial results to support the thesis on no effect of vitamin D supplementation on body weight reduction in children and adolescents with vitamin D insufficiency undergoing a weight management programme. Trial registration no: NCT 02828228; trial registration date: 8 June 2016 registered in: ClinicalTrials.gov.

This venture targets giving a correspondence framework that can improve the legal framework execution and cooperation and furthermore make it simple to lead execution audits. This examination depicts restricted admittance to the right legitimate data just as admittance to courts and court administrations as the essential factors that limit admittance to equity. The basic target fundamental for accomplishing the point incorporates planning an online easy to understand data framework that would improve correspondence and association between legal professionals like legal advisors and disputants. The undertaking uses a subjective methodology that zeroed in on the substance investigation of essential information. Key members were court laborers like attorneys and agents, just as court clients like disputants. Pre-plan discoveries uncovered that current legitimate data frameworks – basically court sites – neglect to recognize their crowd by treating all court clients similarly comparative with the correspondence of lawful data. Likewise, the issue of admittance to equity includes the significant expense of equity also, restricted legal data that elevates admittance to equity. Post-plan discoveries from the online overview directed after the turn of events and execution of the IT curio uncovered a powerful and productive legitimate data framework. Exploration discoveries supported the advancement of an IT antiquity that records for huge shortcomings in current legal data frameworks, for example, their failure to pass on fitting legitimate data intelligently and productively. In outline, the investigation prescribes the reception of saw control to work fair and square of certainty of court clients and the differentiation between court clients to convey the right data to the right crowd.

Evaluating the integrity of structures is an important issue in engineering applications. The use of vibration-based techniques has become a common approach to assessing cracks, which are the most often occurring damage in structural elements. When involving an inverse method, it is necessary to know the influence of the position and the geometry of the crack on the modal parameter changes. The geometry of the crack, both in size and shape, defines the damage severity (DS). In this study, we present a method (DS-SHC) used for estimating the DS for closed and open transverse cracks in beam-like structures by using the intact and damaged beam deflections under its weight and a Stochastic Hill Climbing (SHC) algorithm. After describing the procedure of applying DS-SHC, we calculate for a prismatic cantilever beam the severities for different crack types and depths. The results are tested by comparing the DS obtained with DS-SHC with those acquired from dynamic tests made using professional simulation software. We obtained a good fit between the severities determined in these two ways. Afterward, we performed laboratory experiments and find out that the severities obtained with the DS-SHC method can accurately predict the frequency changes due to the crack. Hence, these severities are a valuable tool for damage detection.

Users of meteorological forecasts are often faced with the question of whether to make a decision now based on the current forecast or whether to wait for the next and hopefully more accurate forecast before making the decision. One would imagine that the answer to this question should depend on the extent to which there is a benefit in making the decision now rather than later, combined with an understanding of how the skill of the forecast improves, and information about the possible size and nature of forecast changes. We extend the well-known cost-loss model for forecast-based decision making to capture an idealized version of this situation. We find that within this extended cost-loss model, the question of whether to decide now or wait depends on two specific aspects of the forecast, both of which involve probabilities of probabilities. For the special case of weather and climate forecasts in the form of normal distributions we derive a simulation algorithm, and equivalent analytical expressions, for calculating these two probabilities. We apply the algorithm to forecasts of temperature and find that the algorithm leads to better decisions relative to three simpler alternative decision-making schemes. Similar problems have been studied in many other fields, and we explore some of the connections.

This paper develops a multi-task learning framework that attempts to incorporate the image structure knowledge to assist image inpainting, which is not well explored in previous works. The primary idea is to train a shared generator to simultaneously complete the corrupted image and corresponding structures --- edge and gradient, thus implicitly encouraging the generator to exploit relevant structure knowledge while inpainting. In the meantime, we also introduce a structure embedding scheme to explicitly embed the learned structure features into the inpainting process, thus to provide possible preconditions for image completion. Specifically, a novel pyramid structure loss is proposed to supervise structure learning and embedding. Moreover, an attention mechanism is developed to further exploit the recurrent structures and patterns in the image to refine the generated structures and contents. Through multi-task learning, structure embedding besides with attention, our framework takes advantage of the structure knowledge and outperforms several state-of-the-art methods on benchmark datasets quantitatively and qualitatively.

Hearing dysfunctions can be classified by type, degree, configuration, time of onset, aetiology, and finally, consequences on speech development. They can be divided into conductive, mixed, central types and sensorineural. Conductive hearing loss (CHL) results from interference with the mechanical transmission of sound through the external and middle ear; it can be congenital, as a consequence of anatomic abnormalities, but it can commonly be acquired following middle ear inflammatory pathologies. Sensorineural hearing loss (SNHL) results from failure to transduce vibrations to neural impulses in the cochlean and is a consequence of an irreversible damage to the differentiated cells which make up the organ of hearing and the acoustic paths at various levels. Mixed hearing loss involves a combination of these two types in the same ear. Studies in neuroscience field have shown that the prevention of cell degeneration is only possible if all the factors taken at the different stages of stem cells’ multiplication and differentiation are administered together. We have demonstrated this in a recent study on the ability of SCDSFs to prevent neurodegeneration in hippocampal cells of the CA1 zone in mice. This study confirms previous findings demonstrating that early developmental zebrafish embryo extracts could act as a modulator of senescence in human mesenchymal stem cells (hMSC) isolated from many adult tissues. These findings have open a promising way for the approaches promoting the rejuvenation and regeneration of different tissues, by-passing stem cell transplantation. In the present clinical trial we have used SCDSFs to study the possible reversion of neurosensory hearing loss, until now considered an irreversible condition.

We explore the importance of curvature in carbonaceaous species transformation and stability, using laser-induced vaporisation to evaporate and ionise a source of curved polyaromatic hydrocarbons: carbon nanobelts. Collision impacts between species cause mass loss and the resultant ions are catalogued via mass-spectrometry. To interpret the mass spectra, we perform a series of “in-silico” simulated systematic hydrogen-loss studies using density functional theory (DFT) modelling, sequentially removing hydrogen atoms using thermodynamic stability as a selection for subsequent dehydrogenation. In an initial sequence of H2 removal, the rings are maintained through stable carbyne chain and pentagon-chain formation, giving rise to circular strained dehydrobenzoannulene species. The chains subsequently break, releasing CH and C2. While theoretical closed-cage routes are identified, they are not observed experimentally. The results can serve as a useful guide to high-energy impact conditions observed in some astrochemical environments.

With the advent of COVID19, the attitude of health authorities around the world, led mainly by the West, demanded a level of proof as evidence for cheap, non-patented remedies while promoting expensive, patented, and untested remedies by using emergency use authorization and special provisions afforded to the status of a pandemic emergency. Western science has neither a tested nor a valid historical basis of a logical system that informs to authenticate scientific practices. Here we use a logical heuristic derived from ancient Buddhist logic, which is consistent with the conduct of modern science. We applied the heuristic to show that enough evidence was available for using cost-effective early therapies such as vitamin D supplementation as a public health measure during the first half of 2020. Strong supporting evidence has since accumulated. Apart from political and financial decisions incompatible with science and other conflicts of interest, a critical barrier to evaluating and approving early therapies appears to be the fallacy that the randomized controlled trial (RCT) is the superior proof method in medical hypotheses, including those for nutrients. Logically, no reason exists why properly designed retrospective, ecological, and naturalistic studies with adequate sample sizes and applied appropriate statistical methods would not be as valid as RCTs, especially when elucidating a causative factor instead of treatment. That assertion is particularly true for nutrient deficiencies, interventions, and other cost-effective therapies. Leading health authorities’ failure or refusal to consider other study types (because of either poor logic or vested interest) probably contributed to the spread of misinformation, symptomatic disease, complications, and deaths from COVID19. Partial immunity derived from vaccines and the later development of more contagious variants—and thus a sense of acceptance that SARS-CoV-2 had progressed from a pandemic to an endemic—shows the hollowness of the initial promotions and mandates of vaccines as a cure. Adequate knowledge was available in 2020 to advise that SARS-CoV-2 will continue to mutate, with variants emerging a few times per year, making the vaccine less effective. Emerging evidence confirms that natural immunity better protects against new variants than vaccination against the spike protein. Had vitamin D been adopted as part of the public health measure through a broader supplementation program in 2020 or even today (through sun exposure or as a prophylactic or adjunct therapy early on), the viral spread and symptomatic disease may have been suppressed, with minimal lockdowns and quarantine, and economic harm. The pandemic could have been halted with a significantly reduced need for hospitalization, complications, and deaths, potentially saving millions of lives.

Background: To compare the loss of preload in absence of loading and after a fixed number of ideal masticatory cycles in two different connection systems using all-on-four prosthetic model. Methods: Two equal models of an edentulous mandible rehabilitated with all-on-four technique with two types of abutment system (MUA and OT-Bridge) supporting a hybrid prosthesis, were used. Initial torque values of the prosthetic fixing screw, after ten minutes from initial screw tightening and after 400000 masticatory cycles were registered using a mechanical torque gauge. Differences between initial and final torque values were reported for each anchoring system and the two systems were finally compared. Results: No statistically significant differences regarding the loss of preload between MUA and OT-Bridge system were found after 400000 masticatory cycles; however, in MUA system it was found between anterior and posterior implant screws. A significant difference in preload loss was found only for MUA system comparing the initial screw torque to that measured after 10 minutes from the tightening in absence of cyclic loadings. Conclusions: MUA and OT-Bridge are reliable prosthetic anchoring systems able to tolerate repeated masticatory cycles also on distal cantilever in all-on-four rehabilitation model without any significant loss of preload in screw tightening

Background: Trichomoniasis is the most common non-viral STI globally and yet is not a reportable disease. Trichomonas Vaginalis is an important source of reproductive morbidity and may increase risk of acquisition and transmission of HIV. WHO and CDC recommend various regimens of Nitro-Imidazoles for treatment. The common Nitro-Imidazoles used for Trichomoniasis are Metronidazole and Tinidazole, which vary in their cost, efficacy and side effect profile and it is relevant to study these factors, for better management of the patients. Objectives: This study aims to compare and study the efficacy, compliance of various treatment regimens, their outcomes and side-effects for Trichomoniasis, among STI clinic attendees in Trinidad. Methods: A clinical trial study was designed and after obtaining the informed consent a routine clinical examination was conducted and the swabs for Trichomoniasis tests were collected for diagnosis from the 692 participants. Out of 692 participants, Eighty two (82) patients with established diagnosis of Trichomonas infection were quasi-randomly treated using different regimens. Compliance to treatment, side effects and outcome were evaluated. Results: The prevalence of the Trichomoniasis in population attending our STI clinic is 11.9% and prevalence of HIV is 9%. Of the total 82 participants for the treatment, 80% were females; nearly 90% of the patients belonged to age group 15-45 years and over 60% were below 30 yrs. Among those diagnosed for Trichomonas vaginalis, 13.3% had associated HIV infection. The compliance with respect to single dose treatment was significantly better than the long duration oral regimen and has significant relation with side effects of the treatment. The outcome is generally better and comparable and shows no significant difference between different treatment regimens used in the study. Conclusions: Metronidazole and Tinidazole are commonly used drugs in various regimens. compliance is better with those treated with Tinidazole and Metronidazole stat, than with other groups. Outcome is comparable between these regimens, especially when combined with other important factors like abstinence and treatment of the partners. The treatment regimens mainly differ in the compliance and side effects profile, which suggests that to improve the compliance the drugs with less side effects, short course regimen would be a preferred choice.

Olfactory dysfunction affects often has severe consequences on patients’ quality of life. The most common complaint in these patients is their reduced enjoyment of food in both patients with olfactory loss and parosmia. How the different types of olfactory dysfunction differ in relation to food and cooking habits, sensory awareness, and food-related quality of life has not yet received much attention. By applying questionnaires on cooking, food, olfactory function, weight changes, sensory awareness, and food-related quality of life, we investigate how various aspects of eating differ between participants with olfactory loss (n=271), parosmia(n=251), and normosmic controls(n=166). Cooking habits in olfactory dysfunction revealed pronounced differences as compared with normosmic controls. Cooking with olfactory dysfunction was associated with e.g., a lack of comfort and inspiration for cooking and an inability to make new foods successfully. Significant differences in cooking were also found between olfactory loss and parosmia. Food items were less familiar in participants with olfactory loss and parosmia, while the ratings of liking food items differed between olfactory loss and parosmia, indicating the importance of adapting ingredients in meals separately for olfactory loss and parosmia. Parosmia was associated with a higher incidence of weight loss, but we found no difference in the food-related quality of life between participants with olfactory loss and parosmia. While olfactory loss and parosmia have wide-ranging consequences on patients’ cooking and food habits, adapting meals to include ‘safer food items’ and integrating multisensory stimulation may be a possible avenue for improving the enjoyment of food.

The Planning and implementation of construction projects are difficult processes and are burdened with many risk elements. The budget spread over time, which is developed on the basis of the schedule, presents the expected distribution of costs throughout the duration of the works, which during the implementation of the project is subject to constant changes resulting from time, cost and organizational factors. Managing construction contracts requires managers to be able to analyze on an ongoing basis the variances of production costs - from the values calculated in the offer cost estimate and assumed in the Budgeted Cost of Work Scheduled. The article attempts to analyze the emerging time and cost deviations using proprietary T/S and T/C monitoring, based on simple indicators of the EVM method. An example of construction of a multi-family housing development was used to study the variances of planned and incurred costs.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

Low soil nitrogen status of savanna soils in Nigeria contributes to the persistent Striga hermonthica (Del.) Benth. infestation that limits maize production. The application of nitrogen fertilizer to Striga-resistant hybrids may reduce Striga infection and increase grain yields. This study assessed the performance of maize hybrids at low (30 kg ha-1) and high (120 kg ha-1) nitrogen application under natural infestation with Striga at Kafin Madaki and Tudun Wada in 2014 and 2015. Results showed that the application of nitrogen at 120 kg ha-1 reduced number of Striga plants by 59% compared to application at 30 kg N ha-1 in Kafin Madaki and by 21% in Tudun Wada. Compared to 30 kg N ha-1, the 120 kg N ha-1 rate also reduced Striga damage rating by 22% in Kafin Madaki and by 33% in Tudun Wada across the hybrids. Hybrids 8338-1 (5.3) and OBASUPER 1 (4.3) were the only entries with Striga damage rating greater than 4.5 (SDR > 4.5) when averaged across the nitrogen levels at both locations. Grain yield was 86 and 98% higher in Kafin Madaki and Tudun Wada, respectively when N was applied at 120 kg N ha-1 than at 30 kg N ha-1. The hybrids M1124-3 and M1227-14 produced grain yields that were significantly higher than those of the other hybrids in all locations. The hybrid 8338-1 produced the lowest grain yield across locations. Our results showed that, the application of 120 kg N ha-1 to Striga resistant maize hybrids will reduce Striga infection and increase grain yield.

Purpose: to assess any differences on marginal bone loss between bone-level or tissue-level dental implants through a review of literature until September 2019. Materials and methods: MEDLINE, Embase and other database were searched by two independent authors. The search was limited to articles in English. Results: The search provided 1028 records and, after removing the duplicates through titles and abstracts screening, 45 full-text articles were assessed for eligibility. For qualitative analysis 20 articles were included, 17 articles of them for quantitative analysis. A total of 1161 patients (mean age 54,4 years) and 2933 implants were observed, 1427 (Tissue-level) and 1506 (Bone-level). The survival rate and the success rate were more than 90%, except for 2 studies with a success rate of 88% and 86.2%. No studies reported any differences between groups in term of success and survival rates. Three studies showed that BL-implants had statistically less marginal bone loss (P< 0.05). Only one study reported statistically less marginal bone loss in TL-implants (P< 0.05). In the most part of the studies, differences between implant types in marginal bone loss were not statistically significant. Conclusion: Despite to the peri-implant tissue around transmucosal implants has been reported to be inflammation-free because of the absence of bacterial infiltration in the micro-gap between the fixture and abutment, no clinical and radiological differences were highlighted between groups from the included studies after a variable period of follow-up ranged between 1 to 5 years.

The results of applying drilling engineering tools in planned deviated and horizontal wells of oil and gas condensate fields have been examined. The basis for the implementation of a comprehensive approach was the information obtained from drilling horizontal wells in the West and East Siberia, Volga-Ural region, and Iraqi Kurdistan. A synthetic model is considered as an example of the data, incorporating geomechanical and geological properties. As a result of the conducted audit of the geomechanical model and drilling process, the methodologies used were further developed to obtain optimal drilling fluid densities, aiming to prevent cavity formation on well walls, hydraulic fractures, and other related issues. The implementation of the Python programming language was introduced in the stages of geomechanical model preparation, resulting in a time acceleration of up to 20%. During the pre-drilling stage, technological operations were synchronized with the geomechanical model, increasing the involvement of process participants through the synchronization of knowledge areas. The interrelation between drilling technology, drilling parameters, properties of flushing fluids, and rock stability analysis was established, ensuring a 5% increase in construction speed (through NPT reduction and modification of existing tools and technological operations) and accident-free drilling of complex deviated and horizontal wells, provided that the recommended drilling parameters are followed.

Understanding the distribution in drought and floods plays an important role in disaster risk management. The present study aims to explore the trends in the standardized precipitation index and extreme precipitation days in China, as well as to estimate the economic losses they cause. We found that in the Northeast China, northern of North China and northeast of Northwest China were severely affected by drought disasters (average damaged areas were 6.44 million hectares) and the most severe drought trend was located in West China. However, in the north of East China and Central China, the northeastern of the Southwest China was severely affected by flood disasters (average damaged areas were 3.97 million hectares) and the extreme precipitation trend is increasing in the northeastern of the Southwest China. In the Yangtze River basin, there were increasing trends in terms of drought and extreme precipitation, especially in the northeastern of the Southwest China, where accompanied by severe disaster losses. By combining the trends in drought and extreme precipitation days with the distribution of damaged areas, we found that the increasing trend in droughts shifted gradually from north to south, especially in the Southwest China, and the increasing trend in extreme precipitation gradually shifted from south to north.

Large quantities of real-time particle data are becoming available from low-cost particle monitors. However, it is crucial to determine the quality of these measurements. The largest network of monitors in the United States is maintained by the PurpleAir company, which offers two monitors: PA-I and PA-II. PA-I monitors have a single sensor (PMS1003) and PA-II monitors employ two independent PMS5003 sensors. We determine a new calibration factor for the PA-I monitor and revise a previously published calibration algorithm for PA-II monitors (ALT-CF3). From the PurpleAir API site, we downloaded 83 million hourly average PM2.5 values in the PurpleAir database from Washington, Oregon, and California between January 1, 2017 and September 8, 2021. Daily outdoor PM2.5 means from 194 PA-II monitors were compared to daily means from 47 nearby Federal regulatory sites using gravimetric Federal Reference Methods (FRM). We find a revised calibration factor of 3.4 for the PA-II monitors. For the PA-I monitors, we determined a new calibration factor (also 3.4) by comparing 26 outdoor PA-I sites to 117 nearby outdoor PA-II sites. These results show that PurpleAir PM2.5 measurements can agree well with regulatory monitors when an optimum calibration factor is found.

Aircraft emissions represent a relevant amount of human induced CO2. Globally, up to 2.5 per cent of such emissions stem from the aviation industry. In order to investigate the effects within the atmosphere, realistic flight profiles are necessary to provide quantitatively tangible values of emissions. The flight profiles and the according fuel consumption can be calculated by using waypoints from flight plans and Base of Aircraft Data (BADA). This paper presents an approach to refine the fuel consumption by integrating the passenger load into the calculation. Since effects of emissions have to be assessed on a greater scale, such as on the European air traffic network, the presented approach provides cost functions for CO2 emissions for different aircraft types and load factors. The cost functions were derived by means of regression analyses of BADA based calculated flight profiles with a step size of one second. The calculations are based on real historic traffic scenarios of several days. The derived aircraft specific fuel burn coefficients enable a simple and efficient integration of CO2 estimations depending on the flight distance, load factor and aircraft type. This can be applied to large traffic scenarios to also study different set-ups such as travel restrictions, other disruptions or an alteration in the traffic system as a whole. In order to enable the assessment of further aspects of such changes to the European air traffic system at large and to foster reproducibility and comparability of related studies, we provide further general-purpose cost estimation functions for several important key characteristics. Besides fuel consumption, we develop cost estimations for air navigation fees and maintenance for conventional aircraft. Those functions are also provided for the design concept of a short-range all-electric aircraft. This propeller aircraft features game-changing technologies such as active laminar flow control, active load alleviation and advanced materials and structure concepts. The approaches discussed in this paper will focus on the generic aspects of aircraft related costs, which can be derived from general available data. For the sake of reproducibility, the results will be made publicly available.

Influence of core flow inlet swirl angle on aerodynamic performances of an exhaust nozzle with scarfed lobed mixer was studied by the validated computational approach. The computational simulation was conducted by resolving the steady form of discretized three-dimensional Reynolds Averaged Navier-Stokes equations with the shear stress transport k-Ω turbulence model. Simulation results depict that swirling motions have ignorable influence on the flow field of the top part in the cross sections slightly downstream of the lobed trailing edge. Besides, for the flow field downstream of the L/D=0.1 cross section, the swirling motions are suggested to cause the clockwise stream-wise vortex to stretch into several smaller-scale vortexes. When the case with a bigger swirling angle is investigated, the induced smaller-scale vortexes are more strengthened by the swirling motions. Concerning the 15° swirling case, the loss caused by the destroyed vortex pattern and the benefit induced by the improved smaller-scale vortexes almost counteract with each other with respect to the thermal mixing efficiency. In the last studied cross section as compared with the baseline case, the case with a maximum swirling angle of 30° has increased 6.94% for the thermal mixing efficiency and decreased 0.42% for the total pressure recovery coefficient.

Wireless cellular communication technology has developed into a very resourceful commodity worldwide. Today, people of all races can hardly live without means of voice and data cellular communication technology. Imprecise propagation loss estimation leads to high power waste, high co-channel interference and poor service quality in cellular communication system networks. This paper proposes a realistic adaptive fine-tuning method for distinctive propagation loss estimation over a microcellular communication radio links based on signal power measurements from Long Term Evolution radio broadband networks, taking non-line of sight (NLOS) and line of sight (LOS) environments into consideration. The methodology is verified by measurements taken in non-line of sight and line of sight signal propagation scenarios. The results showed that the estimated propagation losses using the proposed realistic adaptive tuning models were more accurate than the existing Cost -231 modelling estimation approach.

Indoor air quality and public health have always been an area of prime interest across the globe. The significance of low-cost air quality sensing and indoor public health practices spikes during the time of pandemic and epidemics when indoor air pollution becomes a threat to living beings especially human beings. Indoor diseases are hard to diagnose if they are due to the indoor environmental conditions. A major challenge was observed in establishing a baseline between the indoor air quality sensors and associated diseases. In this work, 10,000+ articles from top literature databases were reviewed using bibliometric analysis to formulate indoor air quality sensors and diseases correlation rubrics to critically review 500+ articles. A set of 200+ articles were selected based on for detailed study based on seven bibliometric indices for publications that used WHO, NIH, US EPA, CDC, and FDA defined principles. This review has been conducted to assist end-users, public health facilities, state agencies, researchers, scientists and air quality protection agencies.

Urban cities in sub-Saharan Africa (SSA) are faced with ambient air pollution. This is an important public health problem with models and limited monitoring data indicating high concentrations of pollutants such as fine particulate matter (PM_2.5). Going through most global air quality index maps, however, information about ambient pollution from SSA is scarce. We evaluated the feasibility and practicality of longitudinal measurements of ambient PM_2.5 using low-cost air quality sensors (Purple Air-II-SD) across thirteen locations in seven countries in SSA. Devices were used to gather data over a 30-day period with the aim of assessing the efficiency of its data recovery rate and identifying challenges experienced by users in each location. The median data recovery rate was 94% (range: 72% to 100%). The mean 24-hour concentration measured across all sites was 38 µg/m³ with the highest PM_2.5 period average concentration of 91 µg/m³ measured in Kampala, Uganda and lowest concentrations of 15 µg/m³ measured in Faraja, The Gambia. Kampala-Uganda and Nnewi-Nigeria recorded the longest periods with concentrations>250µg/m³. Power outages, SD memory card issues, internet connectivity problems and device safety concerns were important challenges experienced when using Purple Air-II-SD sensors. Despite some operational challenges, this study demonstrated that it is reasonably practicable and feasible to establish a network of low-cost devices to provide data on local PM_2.5 concentrations in SSA countries. Such data are crucially needed to raise public-, societal and policymaker awareness about air pollution across SSA.

Climate change from anthropogenic activities represents a serious threat to life in earth. Agriculture releases significant emissions of greenhouse gases (GHG), but also offers low-cost opportunities to mitigate GHG emissions. This paper assesses agricultural GHG emissions in Aragon, one important and representative region for agriculture in Spain. The Marginal Abatement Cost Curve (MACC) approach is used to analyze the abatement potential and cost-efficiency of mitigation measures under several scenarios, with and without taking into account the interaction among measures and their transaction costs. The assessment identifies the environmental and economic outcomes of different combinations of measures. Moreover, we develop future mitigation scenarios for agriculture toward the year 2050, in order to assess the impacts on GHG emissions. Results highlight the importance of assessing biophysical processes in mitigation measures, and the significant effects of interactions between measures that reduce the abatement potential and worsen the cost-efficiency. The inclusion of transaction costs provides a better ranking of measures and a more accurate estimation of implementation costs. The scenario analysis shows how the combinations of measures could reduce emissions and promote sustainable agriculture in the future. Keywords: Climate change; mitigation measures; biophysical processes; cost-efficiency; abatement costs; transaction costs; policy scenarios.

This comprehensive critical review shows how green buildings and energy optimization solutions improve indoor air quality as well as environmental quality (IEQ) and human health. Electricity-efficient green buildings create a better indoor atmosphere and save electricity. Green buildings improve occupant well-being through IAQ, thermal comfort, acoustics, and lighting. Renewable energy, green construction materials, and intelligent technologies increase sustainability and reduce environmental impact. Environmental hazards, architectural design, and societal variables can improve indoor air quality and subsequently reduce health risks linked with poor air quality. The evaluation highlights the pros and cons of low-cost IAQ sensors and equipment. These devices provide valuable insights, but calibration and validation using reference equipment are necessary to ensure accuracy and reliability. Architects, engineers, environmentalists, and policymakers are essential in creating green buildings with high IEQ. Prioritizing occupant comfort, health, and productivity ensures a sustainable and healthy future for future generations. However, continual monitoring and research are needed to improve green building practices and overcome construction problems. Intelligent models for continual on-field calibration of low-cost sensors may improve performance. Green buildings benefit occupants and the environment by optimizing energy use and using IAQ monitoring technologies.

Prestress loss evaluation in prestressed strand is essential for prestressed structures. However, the sensors installed outside the duct can only measure the total prestress loss. The sensors attached on strand inside the duct also have several problems, such as inadequate durability in an aggressive environment, vulnerable damage at tensioning and so on. This paper proposes a new installation method for long-gauge fiber Bragg grating (LFBG) sensor to prevent accidental damage. Then the itemized prestress losses were determined in each stage of the pre-tensioning and post-tensioning according to the LFBG measurements. We verified the applicability of the LFBG sensors for prestress monitoring and the accuracy of the proposed prestress loss calculation method during pre-tensioning and post-tensioning. In the pre-tensioning case, the calculated prestress losses had less deviation from the true losses than those obtained from foil-strain gauges, and the durability of the LFBG sensors was better than foil-strain gauges, whereas in post-tensioning case, the calculated prestress losses were close to those derived from theoretical predictions. Finally, we monitored prestress variation in the strand for 90 days. The itemized prestress losses at each stages of post-tensioning were obtained by the proposed calculation method to show the prospect of the LFBG sensors in practical evaluation.

BACKGROUND: The National Lung Screening Trial (ILST) and the NELSON study showed that lung cancer-specific mortality can be reduced by 20-24% using low-dose computed tomography (LDCT) screening in high-risk populations, due to an increase in early-stage diagnoses. RESEARCH QUESTION: How much lung cancer-related direct costs may be reduced using a LDCT screening programme based on the ILST protocol in a public healthcare system?STUDY DESIGN AND METHODS: Cost analysis of lung cancer screening (LCS) vs. usual care in the framework of the retail price of the Catalan public healthcare system. The LCS group included costs of screening (ILST protocol), treatment cost according to weighted average distribution of TNM staging in the NLST and NELSON trials, lung cancer detection rate (CDR) and smoking cessation intervention. The usual care group included treatment costs based on distribution of TNM staging registered in the Spanish index hospital. RESULTS: In the usual care group, treatment costs were €91,959. In the 5-year duration of the LCS programme, the average expected costs per subject were €1,342 (range €1,054-1,832 depending on malignancy in detected nodules) for screening and €32,431 for treatment, with an expected reduction of €952 based on an average CDR of 1.6%. The decrease in cost resulting from stage shift offsets 70.6% of the costs of the screening programme. INTERPRETATION: Baseline 5-year LCS costs are low according to the ILST protocol. In the Catalan public healthcare system, the expense reduction from the stage shift due to the LCS programme compensates a substantial part of its costs.

Supplier selection/replacement strategies and optimized purchasing policies play a key role in efficient supply chain management in today’s dynamic market. Here we study supplier replacement in a one-level assembly system (OLAS) producing one type of finished product. To assemble the product, we need to provide multi-type components, but assembly will be interrupted if any single component is missing, and incoming units will get hoarded until the missing component arrives. The assembly process can be interrupted by various sources of uncertainty, including delays in component deliveries. There is consequently a non-negligible risk that the assembly process may get stopped any moment. This brings inventory-related costs, which should be minimized. Here we consider discrete lead-time distributions to mimic industry-world reality. We present a model that takes into account not only optimal assignment of component order release dates but also replacement of a critical supplier. For a given unit, we model several alternative suppliers with alternative pricing and lead-time uncertainties, and we evaluate the impact on the total assembly system. For a more general case where several suppliers may be replaced, we propose a genetic algorithm.

At present, the world is now passing a very far different time than normal situation due to the COVID-19 pandemic crisis. The global life-style and human civilization is currently progressing with down-stream that affecting almost every sectors necessary for human civilizations except the current environmental situation. To control the COVID-19 spreading, most of the countries are following lockdown process that reduces human mobility, thus reducing the CO2 emission to the environment. Though the COVID-19 pandemic is a blessing for the present environment, however, the post-COVID world will face a massive thrust of energy and only conventional energy resources may not be enough to mitigate the energy demands. Solar power generation technology mainly the photovoltaic (PV) systems and their advancement can be the leading possibilities to minimize the gap between the power demand and generation. It is now time to think how we can improve the PV power generation in future and the post-COVID world. In this encyclopaedia communication, we report on Nano-technological approach to improve the conversion efficiency of GaAs solar cells. We have designed and optimized several types of nano-structured assemblies that can be implemented to reduce the front surface incident light reflection losses thus can assist to improve the conversion efficiency of GaAs solar cells.

Currently, skin cancer is the most commonly diagnosed form of cancer in humans and is one of the leading causes of death in patients with cancer. Biopsy methods are an invasive research method and are not always available for primary diagnosis. Imaging methods have low accuracy and depend on the experience of the dermatologist. Artificial intelligence technologies can match and surpass visual analysis methods in accuracy, but they have the risk of a false negative response when a malignant pigmented lesion can be recognized as benign. One possible way to improve accuracy and reduce the risk of false negatives is to analyze heterogeneous data, combine different preprocessing methods, and use modified loss functions to eliminate the negative impact of unbalanced dermatological data. The paper proposes a multimodal neural network system with a modified cross-entropy loss function that is sensitive to unbalanced heterogeneous dermatological data. The accuracy of recognition in 10 diagnostically significant categories for the proposed system was 85.19%. The novelty of the proposed system lies in the use of cross-entropy loss when training the modified function with the help of weight coefficients. The introduction of weighting factors has reduced the number of false negative forecasts, as well as improved accuracy by 1.02-4.03 percentage points compared to the original multimodal systems. The introduction of the proposed multimodal system as an auxiliary diagnostic tool can reduce the consumption of financial and labor resources involved in the medical industry, as well as increase the chance of early detection of skin cancer.

For the majority of the contractual arrangements used in construction projects, the owner is not responsible for the cost deviations due to the variability of labor productivity or material price, amongst many other aspects. Consequently, the cost performance of a project may be entirely distinct for the owner and the contractor. Since the majority of the quantitative research on cost estimation and deviation found in the literature adopts the owners’ perspective, this research provides a contribution towards modelling costs and cost deviation from a contractors’ perspective. From an initial sample of 13 residential building and 10 office building projects, it was possible to develop models for cost estimation at the early stage of development including both endogenous and exogenous variables. Although the sample is relatively small, the authors were able to fully analyze all the cost data, using no secondary sources of data (very frequent in cost modelling studies). The statistically significant variables in the cost estimation models were the areas above and below ground and the years following the 2008 financial crisis, including the international bailout (2011-2014) period. For estimating the unit cost, a nonlinear model was obtained with the number of underground and total floor, the floor ratio and the years following the 2008 financial crisis, including the international bailout (2011-2014) period as predictors. For the office buildings, it was also found a statistically significant correlation between the cost deviation and the number of underground floors.

Among all Brazilian economic sectors, the livestock sector stands out due to its large production and high export volume. However, beef production is associated to significant environmental impacts, such as deforestation and greenhouse gas (GHG) emission. The Paris Agreement was settled to avoid that global mean temperature rise up to 1.5 – 2º C by 2100. In 2020, Brazil committed in its nationally determined contribution (NDC) to reduce its GHG emission by 43% until 2030. This study aims to identify the association of beef production and beef cattle emissions, as well as assess predictive GHG emission scenarios for 2030 and value these emissions. To translate the environmental impacts of beef production into economic impacts, and thus amplify the discussion, we valued GHG emissions using the social cost of carbon (SCC). The results showed that the business as usual (BAU) GHG emission derived from beef production would range between 0.423 and 0.634 GtCO₂e in 2030, whereas the maximum emission estimated to meet the NDC should be 0.257 GtCO₂e. The SCC revealed the opportunity to reduce between US $18.8 and $42.6 billion in the cost of BAU emissions from beef production in 2030 if the NDC is met. Lastly, assessing a scenario where climate targets and beef exports are prioritized, between 2-10 kg of beef per capita would be available in the domestic market in 2030. Our results reveal the need and urgency of changes in livestock production to emit less GHG per kg of beef produced, and the avoided monetary cost of reducing emissions.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus 13 voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ 14 constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources 15 on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar 16 PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed 17 using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of 18 simulation and statistical results of EO with other optimization techniques showed that EO is more effective 19 and superior.