In order to further reduce the emissivity of the hydrophobic low infrared emissivity composite coating and improve the mechanical properties of the coating, the dispersant, adhesion enhancer, and defoamer were used to improve the dispersion state of the fillers, the interface structure, and the surface state of the hydrogen silicone oil modified polyurethane/Al composite coating. The effects of dispersant, adhesion enhancer, and defoamer on the micro-structure, emissivity, glossiness, hydrophobic property, and mechanical properties of the coating were systematically studied. The results show that the polycarboxylate anionic dispersant can obviously improve the dispersion state of flake Al powder and nano-SiO2 in the coating, so that the infrared emissivity of the coating can be reduced, and the coating can have higher hydrophobic and mechanical properties. The bonding strength between the resin matrix and the metal substrate of the coating can be significantly improved by the adhesion enhancer through the bridging action, so that the adhesion strength and impact strength of the coating can be significantly improved. The defoamer can significantly reduce the pores in the coating, so that the surface state of the coating can be significantly improved, and the mechanical properties of the coating can be significantly improved. The coating has the best emissivity (0.527), glossiness (4.3), adhesion strength (grade 1), impact strength (40 kg.cm), and hydrophobic property (water contact angle (WCA) is 140o) when the amount of dispersant, adhesion enhancer, and defoamer is 5 wt%, 4 wt%, and 1 wt%, respectively.

In this study, a novel absorbable hemostatic agent was developed using carrageenan (CRG) as a natural polymer and cerium oxide nanoparticles (CeO2 NPs).  CRG-CeO2-0.5 and CRG-CeO2-1 composites were prepared by compositing CRG and CeO2 at a weight ratio of 200:1 and 100:1, respectively. Physio-chemical and structural properties of these compounds were studied and compared with pristine CRG. Upon incorporation of CeO2 nanoparticles into the CRG matrix, significant reductions in hydrogel degradation were observed. In addition, it was noted that CRG-CeO2 exhibited better antibacterial and hemostatic properties than CRG hydrogel without CeO2.The biocompatibility of the materials was tested using the NIH 3T3 cell line and all samples were found to be nontoxic. Particularly, CRG-CeO2-1 demonstrated superior hemostatic effects, biocompatibility, and a lower degradation rate since more CeO2 Nps were present in the CRG matrix. Therefore, CRG-CeO2-1 has the potential to be used as a hemostatic agent and wound dressing.

In this work, three different types of sandwich structures were manufactured using Formica sheet (a paper-based sheet) as skin and perlite/sodium silicate foam as core with/without the paper honeycomb. The sandwich structures were fabricated by attaching Formica sheets on both sides of the honeycomb, perlite/sodium silicate foam, and perlite/sodium silicate foam-filled honeycomb core panels. The flexural characteristics were studied by a three-point bending test and the thermal conductivity was measured using Lee’s thermal conductivity apparatus. The results demonstrated a significant improvement in flexural properties, including core shear stress, facing stress, bending stress, and energy absorption, when incorporating the paper honeycomb reinforcement. The thermal conductivity and flexural properties were found to be well-compatible with the existing building materials for similar applications in the literature. The failure investigation revealed that the sandwiches with paper honeycomb only prematurely failed due to core buckling, whereas the foam-filled honeycomb core-based sandwiches were able to sustain higher loads, exhibiting material failures such as core shear failure, skin rapture, and delamination. It is found that the foam-filled paper honeycomb sandwich structures can withstand higher bending loads compared to foam core-based and paper honeycomb-based sandwich structures. These developed sandwiches offer potential as green materials due to the characteristics of their constituent materials and can find valuable applications in the building thermal insulation.

This experimental study examined the application effect of polycaprolactone (PCL), an organic resin material with excellent elasticity and ductility, on improving the mechanical performance of cellulose nanocrystal (CNC) cement composites. To analyze the effect, a test specimen containing CNC and PCL mixed, containing only CNC, and a control (plain) specimen containing nothing were compared. PCL was compared according to its shape, and in the case of Granules, which is the basic shape, interfacial adhesion with cement was not achieved, so a DCM solution was used to dissolve and use the Granules form. As a method for bonding PCL to the CNC surface, the CNC surface was modified using 3-aminopropyltriethoxysilane (APTES), and surface silylation was confirmed through Fourier transform infrared spectroscopy(FT-IR) analysis. To evaluate the dispersibility according to the application of PCL to the modified CNC, particle size analysis (PSA) and zeta potential analysis were performed according to the PCL mixing amount (0.1, 0.3, 0.5, and 1 vol.% compared with those of CNC) and size distribution. Through the zeta potential value, the highest dispersion stability was shown at 1 vol.%. The cohesive force of CNC was low and the dispersion stability was high according to the application of PCL. According to the results of the dispersion stability evaluation, the degree of hydration of the dissolved PCL 1 vol.%, CNC-only specimens, and plain specimens were analyzed. Hydration products increased by increasing the degree of hydration in the unhydrated area. However, the incorporation of PCL showed a low degree of hydration, and the analysis of strength characteristics also showed a decrease of approximately 27% compared with that of plain specimens. This was because the bonding with SiO2 was not smooth owing to the solvent, thus affecting internal hydration. To investigate the effect of the PCL shape, the compressive and flexural strength characteristics were compared using PCL powder as an additional parameter. The compressive and flexural strength values were improved by approximately 54% and 26%, respectively, compared with those of the plain specimen. Scanning electron microscopy (SEM) analysis determined that the filler effect that made the micropore structure denser, affected the mechanical performance improvement.

This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.

A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an H-shaped steel girder. The composite ratio is crucial and determined by the shear connectors' ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration was proposed.

New hybrid composites based on the inclusion of a vegetal extract, i.e., Boswellia Serrata extract (BSE), rich in boswellic acids, well known as a potent anti-inflammatory natural drug, in a lamellar solid layered double hydroxide (LDH), i.e. a Magnesium Aluminum Carbonate, were developed and characterized in the present work. The adopted LDH exhibits a layered crystal structure, comprised of positively charged hydroxide layers and interlayers composed of carbonate anions and water molecules, thus it was expected to embed negatively charged boswellic acids. In the present case, a calcination process was also adopted on LDH to increase organic acids loading, based on the replacement of original inorganic anions. An accurate investigation was carried out by TGA, PXRD, FT-IR/ATR, XPS and LC-MS to ascertain the nature, interaction, and quantifica-tion of the active molecules of the vegetal extract loaded in the developed hybrid materials. As a result, a significant disruption of the original layered structure was observed in LDH subjected to calcination (LDHc), and this material was able to include a higher amount of organic acids when its composite with BSE was prepared. However, in vitro tests on composites bioactivity, expressed in terms of antimicrobial and anti-inflammatory activity, evidenced LDH-BSE as a better material compared to BSE and to LDHc-BSE, thus suggesting that, though the embedded organic acids amount was lower, they could be more available since not firmly bound to the clay. The composite was able to significantly decrease the number of viable pathogens such as Escherichia Coli and Staphylococcus aureus, as well as the internalization of toxic active species into human cells imposed to oxidative stress in comparison to the BSE.

Keywords: Wood residuals; Forest biomass; Wood composite; Wood floor; Life Cycle Assessment.

Many stable water dispersions of various chemical compositions containing bioactive chemical compounds: copper silicate, titanium dioxide and zinc oxide (and other auxiliary substances) were developed and fabricated - they were used for preparation of thin hybrid coatings having very good antimicrobial properties against gram negative bacteria (Escherichia coli), gram positive bacteria (Staphylococcus aureus) and yeast fungus (Candida albicans). Polyester (PES) nonwovens were modified by dip-coating, and PES and cotton fabrics - by dip-coating and coating methods.

This paper examines some of the largely neglected areas of opportunity to utilize skeletal space structure systems in support of modular, industrialized, economical, sustainable and digital future of the construction industry. In this context, the feasibility of future use of skeletal space structures is studied for a few classes of engineering structures, namely, residential apartment buildings, and offshore platforms, along with their suitability for reconstruction, renovation, modernization and retrofit of damaged buildings and urban areas of cultural heritage significance. Finally, the particulars of lean project management of space structures are discussed with emphasis on engineering and economic factors, production management, environmental aspects, quality management, and reliability, maintainability and sustainability considerations. This article concludes that skeletal space structures can fulfil many of the essential construction requirements of modern societies, especially those facing environmental challenges, all while allowing for design flexibility and mass customization.

Arthroplasty is commonly performed to treat advanced osteoarthritis or other degenerative joint conditions, but it can also be considered for young patients with severe joint damage that significantly limits their functionality and quality of life. Young patients are still at risk of aseptic mobilization and bone resorption due to the phenomenon of stress-shielding that causes an uneven distribution of tensions along the femoral contact surface prosthesis. This phenomenon can be limited by appropriately choosing the material of the prosthesis or by varying its stiffness, making sure that its mechanical behavior simulates that of the femur as much as possible. The aim of this study is to evaluate the mechanical behavior of a prosthesis optimized both in shape and material and in comparing the results with a standard titanium prosthesis. Methods: Through three-dimensional modeling and the use of software finite element method (FEM) such as ANSYS we simulate the mechanical behavior of traditional prosthesis and prosthesis optimized topologically respecting the ASTM F2996-13 standard Results: With topological optimization there is a stress reduction from 987 Mpa to 810 Mpa with a mass reduction of 30%. With the use of carbon fiber, it is possible to further reduce stress to 509 Mpa. Conclusions: The reduction of stress on the femoral stem allows an optimal distribution of the load on the cortical bone thus decreasing the problem of stress-shielding.

A nanocomposite rod-shaped structure with single-walled carbon nanotube (SWCNT) embedded in polypyrrole (PPy) doped with nonafluorobutanesulfonic acid (C4F), SWCNT/C4F-PPy, was synthesized using emulsion polymerization. The hybrid ink was then directly coated on a polyimide film interdigitated with the Cu/Ni/Au electrodes via a screen-printing technique to create a flexible film sensor. The sensor film showed a response of 1.72% at 25 °C/atmospheric pressure when acetone gas of 5 ppm was injected, which corresponds to almost 95% compared to the Si wafer-based array interdigitated with the Au electrode. Additionally, C4F was used as a hydrophobic dopant of PPy to improve the stability of humidity and to produce a highly sensitive film-type gas sensor that provides stable detection even in humid conditions.

Titica vine fibers (TVFs) extracted from aerial roots of Heteropsis flexuosa, from the Amazon region, were 10, 20, 30 and 40 vol% incorporated into an epoxy matrix for applications in ballistic multilayered armor systems (MASs) and stand-alone tests for personal protection against high-velocity 7.62 mm ammunition. The back-face signature (BFS) depth measured for composites with 20 and 40 vol% TVFs used as an intermediate layer in MASs was 25.6 and 32.5 mm, respectively, below the maximum limit set by the international standard. Fracture mechanisms found by scanning electron microscopy (SEM) attested the relevance of increasing the fiber fraction for applications in MASs. The results of stand-alone tests showed that the control (0 vol%) and samples with 20 vol% TVFs absorbed the highest impact energy (Eabs) (212 – 176 J), and consequently limit velocity (VL) values (213 – 194 m/s), when compared with 40 vol% fiber fractions. However, the macroscopic evaluation found that the plain epoxy, referring to control samples, shattered completely. In addition, for 10 and 20 vol% TVFs, the composites were fragmented or exhibited delamination fracture, which contributed to their physical integrity. On the other hand, the composite with 30 and 40 vol% TVFs, whose Eabs and VL varied between 166 – 130 J and 189 – 167 m/s, respectively, showed the best dimensional stability. The SEM images indicated that for composites with 10 and 20 vol% TVFs the fracture mode was predominantly brittle, due to the greater performance of the epoxy resin and the discrete action of the fibers. While for composites with 30 and 40 vol% TVFs, there was the activation of more complex mechanisms such as pullout, shearing and fiber rupture.

Standards are not only crucial for obtaining a certification for practical use, but also an essential guidance for inferring how and what to simulate as well test experimentally. This paper examines the potential applicability of existing standards from various domains, including aerospace and automotive, to Wing-Structure- Integrated high-pressure Hydrogen Tanks (SWITHs). It highlights the associated challenges and uncertainties, acknowledging the absence of a single, all-encompassing standard for SWITHs. We embark on an exploration aimed at identifying alternative standards that are best suited for SWITHs. The analysis scrutinizes existing standards that could potentially facilitate SWITH certification, with a particular focus on the inclusivity of externally loaded hydrogen tanks. Assessment criteria are established to filter standards that best meet the needs of SWITHs. Through this process, we identify two key standards that present themselves as the most promising alternatives. Moreover, we delineate the technical constraints involved in selecting the maximum nominal working pressure for high-pressure tanks intended for burst tests. Our findings reveal a current upper limit of 525 bar, imposed by the limitations of existing test facilities. The study underscores that these standards should serve as flexible guiding frameworks rather than rigid protocols, encouraging progressive development in the SWITH field.

Polymer-based composites represent a separate class of materials in demand by the industry. In comparison with other polymers, UHMWPE is characterized by exceptionally high wear and impact resistance. In this work, compacts were produced from UHMWPE GUR 4120 powder with the addition of Nanoscale Detonation Carbon (NDC) and Single-Walled Carbon Nanotubes (SWCNTs) on a hydro-pneumatic impact device by the Cyclic Impact Compaction (CIC) technique. The obtained samples were subjected to wear resistance test, their hardness and tensile strength were measured. Studies have shown that the addition of NDС and SWCNTs in UHMWPE leads to an increase in hardness by 6.4 and 19.6%, to a decrease in wear by 11.5 and 38.5% and a decrease in the coefficient of friction by 10 and 20%, respectively. However, the tensile strength of UHMWPE decreases by 11.7 and 40.4% and elongation decreases by 11.9 and 30.1% with the addition of NDС and SWCNTs, respectively.

High temperature titanium alloys are widely used in aerospace hot parts, however, the thermal barrier temperature of 600 oC limits its service temperature. In this paper, a two-step hot-dip plating method is proposed to prepare the composite coating containing Ce on the surface of titanium alloy, which can make the oxidation resistance temperature of titanium alloy reach 800 oC The microstructure, phase composition and element distribution of Ce-containing Ti-Al-Si hot-dip coating, Ce-containing Ti-Al-Si pre-oxidation coating and Ce-containing Ti-Al-Si high-temperature oxidation coating were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results show that the Ti-Al-Si hot-dip coating containing Ce is mainly composed of (Ti,Ce)(Al,Si)3 alloy phase layer, and the Ti-Al-Si pre-oxidation coating containing Ce is mainly composed of Ti-Al binary system phase layer and dense Al2O3 layer rich in CeO2. Ce in the high temperature oxidation coating of Ti-Al-Si containing Ce is mainly distributed in Ti3Al, TiAl, TiAl3+Ti5Si3 mixed phase layer and Al2O3. The addition of Ce can promote the formation of continuous Al2O3 layer, improve the uniformity of composite coating, prevent the spread of cracks, and improve the high temperature oxidation resistance of Ti-Al-Si coating.

Ti-Al alloy phase layer/Ti-Al carburizing composite coating was prepared on the surface of titanium alloy by the stepwise coating method of hot dip aluminization and then carburizing. The weight gain results of the composite coating showed that the titanium alloy coated with the composite coating had long-term stability (≥16 days) at 800oC. The microstructure, phase structure and composition of the composite coating were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).The composite coating is composed of an alloy phase layer and a carburized layer. The natural transition of four phases (Ti3Al/TiAl/TiAl2/TiAl3) in the alloy phase layer, significantly improves the interfacial bonding between the coating and the substrate, and slows down the propagation of microcracks through the coating.Al2O3, TiC and C in the carburizing layer improve the surface hardness of the coating, and TiAl2 and Al2O3 also have excellent oxidation resistance at high temperature.

The presented research focused on the evaluation of the novel concept of overmolding technique using self-reinforced composite prepregs and recycled polymer blends. In order to evaluate the effectiveness of the proposed manufacturing technique, several series of materials based on polycarbonate/polyethylene terephthalate (PC/PET) and polycarbonate/polyethylene terephthalate glycol (PC/PETG) blends were prepared. The reinforcing component in the form of overmolded prepreg was made from polyester-based self-reinforced composite (srPET). The prepared materials were compared in terms of mechanical properties and heat resistance; the study was supplemented by thermal analysis measurements (DMTA, DSC). Considering the mechanical characteristics, the overmolding technique turns out to be an effective method of improving the properties of composites, and the increase in impact strength turns out to be particularly beneficial. The increase of the impact strength for overmolded PC/PET blend reached 430 % for PC/PETG sample 330% , while for PC-based composite, only 100%. The expected improvement in thermomechanical properties turned out to be difficult to achieve due to the rapid softening of the srPET prepreg at around 70 °C. However, technological tests and analysis of properties clearly indicated that the use of PC-based blends makes it possible to create a permanent connection with reinforcement based on srPET prepregs, which can significantly expand the potential of applications of this type of materials.

The high level of noise in helicopter cabins considerably compromises the comfort and safety of the pilot and passengers. To verify the feasibility and effectiveness of microperforated panel composite sound absorption structures for noise suppression in helicopter cabins, simulation and experimental studies were conducted on a model of a light helicopter cabin. First, three microperforated composite sound absorption structures for the helicopter cabin wall panel were designed. Then, a finite element model of the main gear/body acoustic vibration coupling was established to obtain the target frequencies of the microperforated composite sound absorption structures; the acoustic effect was verified by simulation. Finally, a model helicopter cabin equipped with the three microperforated composite sound absorption structures was built, and a cabin noise test was performed. The test results showed that the combined microperforated panel acoustic structure and microperforated panel–porous material composite structure realized an overall cabin sound pressure level attenuation of 8–10 dB, on average, in the wide frequency range of 500–2000 Hz, with an amplitude of more than 20 dB. The microperforated panel–acoustic supermaterial composite structure achieved low-frequency sound absorption in the frequency range of 300–450 Hz. The sound absorption effect reached 50%, and it also exhibited good noise reduction effects in the middle- and high-frequency bands.

Based on the daily observation data of 2254 meteorological stations in China from 1961 to 2021 after homogenization and correction, the extreme value analysis method that combines relative threshold and absolute threshold was used to identify extreme climate events in the mainland of China, namely extreme high temperature, extreme low temperature, extreme drought, extreme precipitation and extreme typhoon events. The frequency and linear variation trends of individual extreme events in the past 60 years were investigated. On this basis, the multi extreme events composite risk grade index (MXCI) was constructed, which can objectively reflect the comprehensive characteristics of multi extreme climate events in different regions. The results show that the high value areas of MXCI were mainly located in Southeast China and Southwest China. The MXCI presented a decreasing trend in most of the western and southeastern regions of China, while an increasing trend from Southwest China to the south of Northeast China, due to the frequent occurrence of extreme high temperature, extreme drought and other extreme events in these regions.

This paper presents a new method of preparing a coating on the Ti65 titanium alloy by a two-step procedure comprising hot-dipped aluminum and solid carburization. The effects of the carburization in the presence of NaCl deposit at 810oC have been systematically studied. In this article, the microstructure, morphology, phase composition of the coating, and the corrosion products were investigated by SEM, EDS, and X-ray diffraction. Results indicated that the corrosion resistance of hot dip aluminum/carburizing composite coating was not significantly enhanced by hot dip aluminum coating. This can be attributed to the formation of TiC and Ti3AlC after carburization, which promoted the formation of loose and unprotected TiO2 in the coating during molten salt corrosion. In addition, the oxidation of the carbon atom into CO2 /CO leaded to a high concentration of vacancy in the coating, creating channels for NaCl to penetrate the coating and accelerated the corrosion rate.

The behaviour of steel frame buildings under progressive collapse conditions depends on a combination of several parameters including the interplay between different collapse resistance mechanisms mobilized in different structural components. Previous studies have shown that the extent to which these mechanisms may contribute to progressive collapse resistance depends on the ability of the beam-column connections to undergo large inelastic deformations prior to reaching their deformation capacity limits. For this reason, and due to the important role of their flexural strength and tying capacity in the development of essential collapse resistance mechanisms, the response of beam-column connections is one of the most important features of progressive collapse performance. Based on the knowledge gained through previous studies on the mechanics of the problem, the role of the connections is critically reviewed by examining the results of several experimental studies conducted during the past decade. The factors that may adversely affect progressive collapse resistance – such as failure modes of certain connection types – are evaluated, and novel approaches of limiting these factors which are currently under development are reviewed. The assessment of these parameters leads to useful conclusions of practical significance, while highlighting the aspects of the problem that need further study and understanding.

Some of Iran's gas resources are known as sour gas because one of the major by-products of this gas is water. In fact, natural gas is combined with water vapor in underground reservoirs. In some areas, the amount of water vapor in natural gas is so high that it can be used as a source of drinking water. However, it should be noted that water vapor in natural gas may exacerbate corrosion in pipes and industrial equipment, and the combustion of more natural gas produces high temperatures that can lead to the production of nitrogen oxides (NOx), which They are the cause of air pollution. This is while the processed gas has a standard percentage composition in which the amount of water has the lowest position. The removal of moisture from natural gas is due to the need to prevent the reduction of the calorific value of the gas and also to purify the gas in order to achieve the necessary standards for delivering gas to petrochemicals, industries and domestic uses. The main goal of this research is to investigate the influencing parameters on zeolite TiO2 nanocomposite membranes in order to absorb moisture from gas. For this reason, with the construction of a TiZ-V membrane as a standard membrane, the result of the initial evaluation of a suitable membrane for gas dehumidification was made, and this membrane was placed as a standard for measuring the effect of the manufacturing parameters in a way that in each stage of membrane construction It was found that it was different from standard TiZ-V membrane only in terms of one parameter. This type of investigation made it possible to determine the effect of various effective parameters in membrane construction on efficiency. The findings showed that increasing the concentration of SiO2 has the greatest effect on increasing the water flux of the membrane. According to the other findings of this study, the effect of increasing the reaction time of the vapor phase carrier has been to reduce the process of paternity selectivity loss at higher pressures. Although due to the safety limitation of the equipment to measure the efficiency of the membrane at pressures higher than 7 bar, this measurement was not carried out, but charts were presented regarding the state of the water in the water, which were a measure of the superiority of the water in the water in comparison to the gas in the water, which is the higher water in the water It is an indicator of the appropriateness of the membrane's efficiency at its corresponding pressure, so that the examination of the difference between these two graphs shows the possibility of using the membrane at higher pressures

Polymeric composites such as Poly-ether-ether-ketone (PEEK)/carbon fiber (CF) have been widely utilized due to outstanding performances such as high specific strength and specific modulus. The PEEK/CF components via powder-bed fusion additive manufacturing usually show brittle fracture behaviors induced by their poor interfacial affinity and inner voids. These defects are strongly associated with powder packing quality upon deposition. The particle dynamic model has been widely employed to study the interactions of particle motions. Powder property, bulk material property, and interfacial features of composite powders are key factors in the particle dynamic model. In this work, an efficient and systematic material evaluation is developed for composite powders to investigate their deposition mechanism. The discrete element method is utilized to simulate the dynamic behaviors of PEEK/CF composite powders. The powder properties, bulk material properties, and interfacial features of powders are calibrated and justified by experimental measurement, numerical simulation, and design of experiments. The particle dynamic model can well explain the powder flow behaviors and interactions. It reveals that the addition of short CF particles can assist the flow of PEEK powders and improve the packing quality of the composite powders.

Although the Orthotropic steel decks (OSDs) have been widely used in the construction of long-span bridges, there are frequently reported fatigue cracks after years of operation, and the bridge deck overlay also presents severe damage due to OSD crack-induced stiffness reduction. The ultra-high performance concrete (UHPC), recognized as the most innovative cementitious composites and the next generation of high-performance materials, shows high strength, ductility, toughness and well performance on durability. After its first application to the OSD bridge in early 2000s, the orthotropic Steel-UHPC composite deck has been comprehensively studied worldwide. This review will summarize some important studies and findings on behavior and fatigue performance of orthotropic steel-UHPC composite deck. The existing studies and engineering application indicate that such deck system presents good bending behavior and high fatigue performance. The failure mode of shear studs in UHPC layer is dominated by shear fractures. The cracking of UHPC layer shall consider the superposition effect of stress from both the whole bridge structure and local decks. While some reasonable structural details in the traditional OSD may not work for the orthotropic steel-UHPC composite deck. It is recommended to evaluate the stress behavior and structural parameters, as well as fatigue life by conducting the field test under in-service traffic conditions.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

Several methods of processing wood into strong, durable products for the construction industry provide transformative opportunities to substitute for less sustainable building materials. Carbon storage is a further advantage, with the added possibility of combustion for bioenergy at end of life. Intense research activity in this area is expected to open up new markets for wood fiber during the lifetime of trees now being planted. Here, wood-derived materials are classified according to the particle size, from metres to nanometres, into which the wood is fragmented before reconstitution. Materials made by densifying or chemically modifying solid wood with no fragmentation are already in production for exterior doors, window frames and cladding, with improved uniformity and stability compared with unmodified wood. Pre-commercial developments promise further gains in durability and strength. Emerging developments extend these process technologies to wood that has been chipped or stranded or pulped, retaining the above advantages over raw timber for weather-facing applications and adding processability by moulding or extrusion. Crucially, the raw material does not then need to be sawn timber but can be bioenergy-grade wood biomass. This will facilitate afforestation strategies that combine the aims of carbon sequestration and biodiversity.

Statistical based reconstruction methods and signal processing tooling techniques are implemented and used to detect delaminations or debondings within composite items. From literature it appears that, although a single procedure for the estimation of the structural health is a fast solution, a multiple analysis based on different reconstruction methods or different damage parameters could provide more detailed information about the location and the severity of possible failures. This work discusses the advantage of using cross-correlation analysis in a data-driven approach based on ultrasonic guided waves (GW) tomographic technique and piezoelectrics (PWAS) in pitch-catch configuration. In this sense, this work evidences an improvement in damage detection when the cross-correlation is included as part of the GW-based system for damage assessment approach. The specimens used as test structures to demonstrate the validity of the methodology derive from an aircraft wing test article where damages are specified as skin delamination produced by low energy impact.

The design and engineering of antibacterial materials is key for preventing bacterial adherence and proliferation in biomedical and house-hold instruments. Silver nanoparticles (AgNPs) and chitosan (CHI) are broad-spectrum antibacterial materials with different properties, whose combined application is currently under optimization. This study proposes the formation of antibacterial films with AgNPs embedded in carboxymethylcellulose/chitosan multilayers by the layer-by-layer (LbL) method. The films were deposited onto nanoporous silicon (nPSi), an ideal platform for bioengineering applications, due to its biocompatibility, biodegradability, and bioresorbability. We focus on two alternative multilayer deposition processes: cyclic dip coating (CDC) and cyclic spin coating (CSC). The physicochemical properties of the films were the subject of microscopic, microstructural and surface-interface analyses. The antibacterial activity of each film was investigated against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria strains as model microorganisms. According to the findings, CDC technique produced multilayer films with higher antibacterial activity for both bacteria compared to the CSC method. Bacteria adhesion inhibition was observed from only 3 cycles. The developed AgNPs-multilayer composite film offers advantageous antibacterial properties for biomedical applications.

The use of carbon nanotubes to improve the mechanical properties of polymers is one of the promising directions in materials science. The addition of single-walled carbon nanotubes (SWCNT) to a polymer results in significant improvement of mechanical, electrical, optical, and structural properties. However, the addition of SWCNTs does not always improve the polymer properties. Also, when a certain content of SWCNTs is exceeded, the mechanical properties of the nanocomposite are getting worse. This article reports the results of computer simulations for predicting the mechanical properties of polymer/single-walled carbon nanotube nanocomposites. The efficiency of reinforcing polymer composites is considered depending on the concentration of carbon nanotubes in the polymer matrix, their size and structure. The elastic moduli of the nanocomposites were predicted using computer simulations for unit cell tension (0.1%). General trends in the mechanical properties of composites with polypropylene, poly (ethyl methacrylate), polystyrene matrices and SWCNTs are shown.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

The following system of equations {x_1 \cdot x_1=x_2, x_2 \cdot x_2=x_3, 2^{2^{x_1}}=x_3, x_4 \cdot x_5=x_2, x_6 \cdot x_7=x_2} has exactly one solution in ({\mathbb N}\{0,1})^7, namely (2,4,16,2,2,2,2). Hypothesis 1 states that if a system of equations S \subseteq {x_i \cdot x_j=x_k: i,j,k \in {1,...,7}} \cup {2^{2^{x_j}}=x_k: j,k \in {1,...,7}} has at most five equations and at most finitely many solutions in ({\mathbb N}\{0,1})^7, then each such solution (x_1,...,x_7) satisfies x_1,...,x_7 \leq 16. Hypothesis 1 implies that there are infinitely many composite numbers of the form 2^{2^{n}}+1. Hypotheses 2 and 3 are of similar kind. Hypothesis 2 implies that if the equation x!+1=y^2 has at most finitely many solutions in positive integers x and y, then each such solution (x,y) belongs to the set {(4,5),(5,11),(7,71)}. Hypothesis 3 implies that if the equation x(x+1)=y! has at most finitely many solutions in positive integers x and y, then each such solution (x,y) belongs to the set {(1,2),(2,3)}. We describe semi-algorithms sem_j (j=1,2,3) that never terminate. For every j \in {1,2,3}, if Hypothesis j is true, then sem_j endlessly prints consecutive positive integers starting from 1. For every j \in {1,2,3}, if Hypothesis j is false, then sem_j prints a finite number (including zero) of consecutive positive integers starting from 1.

Purpose: This study aimed to evaluate the nanomechanical properties and chemical composition of restorative materials and dental surfaces using different toothpastes. Methods: Enamel (n=60) and dentin (n=60) bovine blocks were obtained and restored using resin-modified glass ionomer cement (RMGIC, n=30) or composite resin (CR, n=30) to form the dentin adjacent to RMGIC (DRMGIC), enamel adjacent to RMGIC (ERMGIC), dentin adjacent to CR (DCR), and enamel adjacent to CR (ECR). After restoration, one hemiface of each specimen was coated with an acid-resistant varnish to create the control (C) and eroded (E) sides (erosion: 5 days, 4 × 2 min/day; 1% citric acid / abrasion: 2 × 15 s followed by immersion on slurries 2 min). Three toothpastes were used: without fluoride (WF; n=10), sodium fluoride (NaF; n=10), and stannous fluoride (SnF2; n=10). The specimens were analyzed for nanohardness (H), elastic modulus (Er), and chemical composition using energy-dispersive X-ray spectroscopy (EDS) and Raman microscopy. Data were analyzed using ANOVA two-way repeated measures and Tukey’s test (α = 0.05). Results: The NaF presented lower values of H for DRMGIC-C, with a statistical difference for WF (p < 0.05). SnF2 resulted in lower Er values for ERMGIC-E and RMGIC-E than WF and NaF (p < 0.05). WF showed lower calcium and phosphorus concentrations for DCR-E than other types of toothpastes (p < 0.05). Only stannous-based toothpaste damaged the elasticity of eroded glass ionomer restorations performed in enamel. Toothpastes with fluoride was capable for maintaining main chemical elements of dentin adjacent to restorative materials under challenge conditions.

As one of the most critical parameters to evaluate the quality and performance of mobile phones, real-time temperature monitoring of the mobile phone integrated chips is vitally important in the electronics industry. Although several different strategies for chip surface temperature measurement have been proposed in recent years, distributed temperature monitoring with the high spatial resolution is still a hot issue to be solved urgently. In this work, a fluorescent film material with photothermal properties containing thermosensitive upconversion nanoparticles (UCNPs) and polydimethylsiloxane (PDMS) is fabricated for chip surface temperature monitor-ing. The presented fluorescent films have thicknesses ranging from 23 to 90 μm and are both flexible and elastic. Using the fluorescence intensity ratio (FIR) technique, the temperature sens-ing properties of these fluorescent films are investigated. The maximum sensitivity of the fluo-rescent film was measured to be 1.43% K-1 at 299 K. By testing the temperature at different posi-tions of the optical film, a distributed temperature monitoring with a high spatial resolution down to 10 μm on the chip surface is successfully achieved. It is worth mentioning that the film maintains stable performance even under pull stretch up to 100%. The correctness of the method is verified by taking infrared images of the chip surface with an infrared camera. These results demonstrate that the as-prepared optical film is a promising anti-deformation material for high spatial resolution temperature monitoring on-chip surfaces.

This study is focused on the mechanical properties of WC-Co composites obtained via Selective Laser Sintering using PA12 as a binder. The as-printed samples were thermally debonded, and sintered, first in vacuum, and then sinter-HIPed at 1400oC, using 50 bar Ar, which has led to relative densities up to 66 %. Optical metallographic images show a microstructure consisting of WC, with an average grain size in the range of 1.4 – 2.0 µm, with isolated large grains, in a well-distributed Co matrix. The shrinkage of the samples was 43 %, with no significant shape distortion. The printing direction of the samples has a great impact on the transversal rupture strength (TRS). Nevertheless, the bending strength was low, with a measured maximum of 612 MPa. SEM images of the fracture surface of TRS samples show the presence of defects that constitute the cause of the low measured values. The hardness values position the obtained composites in the range of medium coarse classical cemented carbides. The results were also related to the amount of free Co after sintering, close to the initial one, as assessed by magnetic measurements, indicating a low degree of interaction with PA12 decomposition products.

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

Bamboo engineering materials are green, high-strength, tough, durable, and structurally safe, and have promising application prospects in various modern green and low-carbon buildings. To invest the vibration behavior of new bamboo bundle veneer -laminated lumber (BLVL) for use in floor slabs, this study designed two kinds of full-scale vibration tests under a pedestrian load: an extraction hammer impact test, and a static concentrated load test, it is expected to provide theoretical and data support for the application of bamboo bundle veneer laminated composite materials in the construction field. The results showed that the self-oscillation frequency and mid-span deflection of the BLVL composite met the requirements of multiple relevant regulations when used as the structural material of floor slabs. The BLVL floor slab had a higher flexural stiffness and better vibration-damping performance than the OSB floor slab. The first-order self-oscillation frequency of the BLVL composite floor slab was 13.769 Hz, the damping ratio of the first three orders of modalities was 1.262–2.728%, and the maximum static deflection in the span of the joist was 0.932 mm under a 1 kN concentrated load. The 1 kN static deflection of the BLVL was reduced by 22.33%, and the root mean square (RMS) acceleration of the walking load response was significantly lower than that of the OSB floor slab. The preparation of BLVL composite materials by homogeneous lamination of bamboo bundle veneer and wood veneer may help improve the vibration behavior of bamboo-wood structures such as floor slabs and walls.

This article introduces simulations of theoretical material with controlled properties for the evaluation of the effect of key parameters, as volumetric fractions, elastic properties of each phase and transition zone on the effective dynamic elastic modulus (Ed). The accuracy level of classical homogenization models was checked regarding the prediction of Ed. Numerical simulations were performed with finite element method (FEM) for evaluations of the natural frequencies and their correlation with Ed, through frequency equations. An acoustic test validated the numerical results and obtained the elastic modulus of concretes and mortars at 0.3, 0.5 and 0.7 water-cement ratios (w/c). Hirsch calibrated according to the numerical simulation (x = 0.27) exhibited a realistic behavior for concretes of w/c = 0.3 and 0.5, with 5% error. Nevertheless, for w/c = 0.7, Ed approached Reuss model, similarly to theoretical triphasic materials. Hashin-Shtrikman bounds is not perfectly applied to theoretical biphasic materials under dynamic situations.

A novel flexible humidity sensor, incorporating gold nanoparticles (Au NPs) and a trifunctional organosilica compound, has been developed through the integration of sol-gel processing, free radical polymerization, and self-assembly techniques. The trifunctional organosilica was initially synthesized by modifying (3-mercaptopropyl)trimethoxysilane (thiol-MPTMS) with 3-(trimethoxysilyl)propyl methacrylate (vinyl-TMSPMA). Subsequently, a hydrophilic polyelectrolyte, [3(methacryloylamino)propyl]trimethyl ammonium chloride (MAPTAC), was grafted onto the MPTMS-TMSPMA gel. The Au NPs were assembled onto the thiol groups present in the MPTMS-TMSPMA-MAPTAC gel network. The compositional and microstructural properties of the Au NPs/MPTMS-TMSPMA-MAPTAC composite film were investigated utilizing Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The presence of thiol groups and mesoporous silica skeletons ensured the stability of the humidity-sensing film on the substrate under highly humid conditions, while the hydrophilic groups functioned as humidity-sensitive sites. This innovative humidity sensor demonstrated high sensitivity, acceptable linearity, minimal hysteresis, and rapid response time across a broad range of working humidity levels. Based on the complex impedance spectra analysis, hydronium ions (H₃O⁺) were determined to govern the conductance process of the flexible humidity sensor.

Pancakes are fast food snacks that are generally made with the basic ingredients of wheat flour, which is an imported commodity and detrimental for people who are allergic to gluten. To reduce the use of wheat, alternative raw materials derived from local commodities are used, such as modified cassava flour (mocaf), arrowroot flour, and suweg flour. The experiment was carried out by mixing mocaf flour, arrowroot flour, and suweg flour to produce composite flour with a ratio of 70:15:15 (CF1), 70:20:10 (CF2), and 70:20:5 (CF3). The result showed that the ratio of mocaf flour, arrowroot flour, and suweg flour had a significant effect on pasting temperature, peak viscosity, hold viscosity, breakdown viscosity, setback, L*, a*, hue, whiteness, ∆E, as well as swelling volume and solubility on the characteristics of the composite flour It also had a significant effect on the texture characteristics of hardness, adhesiveness, chewiness, color characteristics L*, a*, whiteness, ∆E, and preference for the flavor of gluten-free pancake products. It is known that the best formulation for the resulting pancake product is P1, with the addition of a 70% ratio of mocaf flour, 15% ratio of arrowroot tuber flour, and 15% ratio of suweg flour.

We work within a Winterberg framework where space, i.e., the vacuum, consists of a two component superfluid/super-solid made up of a vast assembly (sea) of positive and negative mass Planck particles, called planckions. These material particles interact indirectly, and have very strong restoring forces keeping them a finite distance apart from each other within their respective species. Because of their mass compensating effect, the vacuum appears massless, charge-less, without pressure, net energy density or entropy. In addition, we consider two variable models, where, , is Newton’s constant, and, , increases with an increase in cosmological time. We argue that there are at least two competing models for the quantum vacuum within such a framework. The first follows a strict extension of Winterberg’s model. This leads to nonsensible results, if increases, going back in cosmological time, as the length scale inherent in such a model will not scale properly. The second model introduces a different length scale, which does scale properly, but keeps the mass of the Planck particle as, the Planck mass. Moreover we establish a connection between ordinary matter, dark matter, and dark energy, where all three mass densities within the Friedman equation must be interpreted as residual vacuum energies, which only surface, once aggregate matter has formed, at relatively low temperatures. The symmetry of the vacuum will be shown to be broken, because of the different scaling laws, beginning with the formation of elementary particles. Much like waves on an ocean where positive and negative planckion mass densities effectively cancel each other out and form a zero vacuum energy density/ zero vacuum pressure surface, these positive mass densities are very small perturbations (anomalies) about the mean. This greatly alleviates, i.e., minimizes the cosmological constant problem, a long standing problem associated with the vacuum.

The aim of this study was to assess the ability of multiscale sample entropy (MSE), refined composite multiscale entropy (RCMSE), and complexity index (CI) to characterize gait complexity through trunk acceleration patterns in subjects with Parkinson's disease (swPD) and healthy subjects, regardless of age or gait speed. The trunk acceleration patterns of 51 swPD and 50 HS were acquired using a lumbar-mounted magneto-inertial measurement unit during their walking. MSE, RCMSE, and CI were calculated on 2000 data points, using scale factors (τ) 1-6. Differences between swPD and HS were calculated at each τ, and the area under the receiver operating characteristics, optimal cutoff points, post-test probabilities, and diagnostic odds ratios were calculated. MSE in the antero-posterior direction at τ 4 and τ 5, and MSE in the ML direction at τ 4 outperformed the other entropy measures in terms of discriminative ability and characterized the gait of swPD with 79%, 82%, and 78% probabilities, respectively, and correlated with the motor disability, pelvic kinematics, and stance phase. Using a time series of 2000 data points, a scale factor of 4 or 5 in the MSE procedure can be considered as a marker of gait variability and complexity in swPD.

We present a new interpretation of the Higgs field as a composite particle made up of a positive, with, a negative mass Planck particle. According to the Winterberg hypothesis, space, i.e., the vacuum, consists of both positive and negative physical massive particles, which he called planckions, interacting through strong superfluid forces. In our composite model for the Higgs boson, there is an intrinsic length scale associated with the vacuum, different from the one introduced by Winterberg, where, when the vacuum is in a perfectly balanced state, the number density of positive Planck particles equals the number density of negative Planck particles. Due to the mass compensating effect, the vacuum thus appears massless, charge-less, without pressure, energy density, or entropy. However, a situation can arise where there is an effective mass density imbalance due to the two species of Planck particle not matching in terms of populations, within their respective excited energy states. This does not require the physical addition or removal of either positive or negative Planck particles, within a given region of space, as originally thought. Ordinary matter, dark matter, and dark energy can thus be given a new interpretation as residual vacuum energies within the context of a greater vacuum, where the populations of the positive and negative energy states exactly balance. In the present epoch, it is estimated that the dark energy number density imbalance amounts to, , per cubic meter, when cosmic distance scales in excess of, , are considered. Compared to a strictly balanced vacuum, where we estimate that the positive, and the negative Planck number density, is of the order, particles per cubic meter, the above is a very small perturbation. This slight imbalance, we argue, would dramatically alleviate, if not altogether eliminate, the long standing cosmological constant problem.

Prime number-related issues can be viewed from drastically different perspectives by examining the close connections between prime numbers and composite numbers. We think that multiple perspectives are the pillars on the path to solutions so we have created this study. As a result of the study, we proposed two new formulas by presenting three theorems and one proof for each theorem, a total of three proofs. We proved that the formula p · n + p returns a composite number in the first of the theorems, which is the preliminary theorem. Our first theorem except the preliminary theorem is that the formula p · n + p returns all composite numbers, and we proved that too. Finally, we created Theorem II using Theorem I to use in our other work and proved that the formula 2 · n · p + p returns all odd composite numbers, which is Theorem II. Afterward, we presented the similarities of the 2 · n · p + p formula we put forth with another known formula.

The literature has well established prestressing in concrete beams and its calculation procedures. However, its use in composite steel-concrete beams has increased despite main normative codes lacking a specific approach for it. Designers must, in most cases, combine the available criteria to calculate the standards of steel and reinforced concrete structures. This study aimed to formulate this optimization problem and analyze CO2 emissions for the optimal design of composite steel-concrete beams with external prestressing. The design variables for the optimization problem include cross-section of laminated or welded profiles, slab height, characteristic strength of concrete to compression, and number of tendons. We obtained a solution for the optimization problem via a genetic algorithm (GA) and a particle swarm optimization one (PSO). Comparative analysis with experimental example and with optimization problem of prestressed steel beam are performed. An parametric analysis to several spams is performed, which enabled to evaluate the factors that most impact CO2 emissions. According to results, the chosen algorithms effectively obtained solutions for the problem, and PSO usually provided better results than GA. Regarding the final solution composition, steel contributes the most to emissions, welded profiles provided better solutions than laminated ones, and laminated spans of up to 17.5m and welded ones up to 27.5m dispensed with tendons.

In the present study, piecewise integrated composite (PIC) bumper beam for passenger cars was proposed and design optimisation process for composite bumper beam against IIHS test was carried out with the help of machine learning. Several elements in IIHS bumper FE model have been assigned to be references, in order to collect training data which, allow the machine learning model to study the method of predicting loading types of each finite element. 2-D and 3-D implementations were provided by machine learning models, which determined stacking sequences of each finite element in PIC bumper beam. It was found that the PIC bumper beam, which was designed by machine learning model has direct impact on reducing the possibility of failure as well as increasing bending strength effectively than conventional composite bumper beam. Moreover, 3-D implementation produced better results compared with 2-D implementation since it was preferable to choose loading type information which was achieved from surroundings when the target elements were located either at corner or junction of planes instead of using information came from the same plane of target.

The bond index is an indicator of the grindability of the material and is widely used in the preparation of mineral raw materials and the cement industry. Paper offers new, abbreviated and simplified procedure to determine Bond work index that relies on first-order kinetics law and can be performed with any number of grinding cycles, depending on the desired accuracy of the required data. The parameters G and P80 of each grinding cycle are multiplied by the newly founded coefficients giDT and piDT to obtain values approximately equal to these parameters of the last grinding cycle when the equilibrium state is reached in the standard test. The paper presents comparative results obtained by standard Bond and new shortened procedure on individual samples of andesite, limestone, copper-ore and smelter slag and on composite samples of andesite from limestone and copper-ore with smelter slag in different mass ratios. As the number of grinding cycles increases, the precision of the shortened procedure increases, and the mean square error decrease 3.59%, 2.61% and 1.74% for two, three and four grinding cycles.

Mechanically strong and thermally stable films obtained from a water-based polyurethane (PU) dispersion with small (0.1–1.5 wt.%) additions of graphene oxide nanosheet (GO) were studied through elemental analysis, X-ray photoelectron spectroscopy, differential thermogravimetry, and Raman spectroscopy. Moreover, the depletion of near-surface layers in nitrogen was presented for all the samples under study. It was found that the introduction of GO into a PU matrix was ac-companied by a partial reduction of graphene oxide nanosheet and an increase in the concentra-tion of defects in its structure.

This report aimed to know the performance of local mineral-based composite ceramic. The materials used consist of Indonesian local minerals, which are jarosite and manganite minerals as sources of oxide iron and Mangan. The materials were synthesized using the precipitation method, whereas composite ceramic was fabricated using a screen printing method and fired at 600 oC using a furnace. The results of the characterizations indicate that the sample forms three phases on diffraction peaks. The differences in the resistance values in ambient and ethanol environments indicate that the sample has very different responses. The high porosity of the sample greatly support the gas adsorption process. Thus, the sample has a high level of sensitivity. With the above characteristics, the composite ceramic which was fabricated has the potential to be applied to gas sensors, especially ethanol gas sensors.

Ecuador is the world's fifth largest cocoa producer, generating hundreds of annual tons of residues from this fruit. This research aims to value this residual (cocoa pod husk) by using it as raw material to obtain pectin, which is widely used in the food and pharmaceutical industries. For them, the extraction of three different organic acids with GRAS status (and therefore safe for their use), citric, malic and fumaric acids, were studied. In addition, two other factors, temperature (70-90°C) and extraction time (60-90 min), were explored in a central composite design of experiments. Under the conditions of the experiment, it was obtained that the best yields were reached for citric acid, malic acid and fumaric acid and for ~86 min of extraction time. The temperature did not show a significant influence on the yield. The pectins obtained under optimal conditions were characterised, showing their similarity with commercial pectin. However, the equivalent weight and the esterification degree of the pectin obtained with fumaric acid classify it as having a high equivalent weight and a low degree of esterification. It differs significantly from the other two acids, perhaps due to the limited solubility of fumaric acid.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

Nano/micron-sized bioactive glass (BG) particles are attractive candidates for both soft and hard tissue engineering. They can chemically bond to the host tissues, enhance new tissue formation, activate cell proliferation, stimulate the genetic expression of proteins, and trigger unique an-ti-bacterial, anti-inflammatory, and anti-cancer functionalities. Recently, composites based on bi-opolymers and BG particles have been developed with various state-of-the-art techniques for tis-sue engineering. Gelatin, a semi-synthetic biopolymer, has attracted the attention of researchers because it is derived from the most abundant protein in the body, viz., collagen. It is a polymer that can be dissolved in water and processed to acquire different configurations, such as hydro-gels, fibers, films, scaffolds, etc. Searching "bioactive glass gelatin" in the tile on Scopus renders 80 highly relevant articles published in the last ~10 years, which signifies the importance of such composites. First, this review addresses the basic concepts of soft and hard tissue engineering, in-cluding the healing mechanisms and limitations ahead. Then, current knowledge on gelatin/BG composites including composition, processing and properties is summarized and discussed both for soft and hard tissue applications. This review explores physical, chemical and mechanical features and ion-release effects of such composites concerning osteogenic and angiogenic respons-es in vivo and in vitro. Additionally, recent developments of BG/gelatin composites using 3D/4D printing for tissue engineering are presented. Finally, the perspectives and current challenges in developing desirable composites for the regeneration of different tissues are outlined.

The main purpose of this study was to develop a model for predicting the quality of holes drilled in the root part of a spar of helicopter main rotor blades made of the Glass Fiber Reinforced Plastic (GFRP)-Ti multilayer polymer composite. As the main quality criterion, delaminations at the entry and exit of the drill from the hole were taken. In the experimental study a conventional drill and two modified geometry drills: a double-point angle drill and a dagger drill were used. Preliminary experiments showed the best hole quality when using modified drills, which allowed further detailed study only with both modified drills at different drilling speeds and feed rates. Its results in the form of training sets were used to build the Artificial Neural Networks (ANNs) to predict delamination at the entry and exit of drilled holes. The analysis of the fitted response functions, presented as 3D surfaces plots and superimposed contour plots, made it possible to choose the better tool - a double-point angle drill and determine the optimal area for drilling speed and feed rates, confirming that the prediction of the quality and productivity of machining composites based on ANN is an effective tool to search and quantify the quality criteria of such technologies.

Probiotics are namely yeast and bacteria which are regarded as dietary supplements and food. Many probiotics are being commonly used now, the most frequently used, lactic acid bacteria are called Lactobacillus and Bifidobacterium. Many of the diseases associated with GIT are related to microbiota found in GIT, an imbalance of which causes gastrointestinal diseases. Probiotics, in light of scientific literature, are thought to play an important role in relieving symptoms of many diseases associated with GIT, i.e. beneficially regulating the microbiota composition. In the present review, we aimed to highlight the main considerations for main probiotic formulations to date. This study reviews the role of different probiotic formulations introduced so far in treating GI diseases in cohort ageing ≤18 years. We searched PubMed and Clinicaltrials.gov without any restrictions. This study comprises the descriptive and comparative analysis between Single-organism and Composite probiotics. These GI diseases include NEC, FAP, AGE, Acute Diarrhea, Ulcerative Colitis and etc. The results have been categorized according to title and outcomes. The positive outcomes emphasize the drug’s effectiveness in improving health and the negative outcome elaborates on the adverse effects the drug may have shown. Conclusively, discussed practices will assist in reducing GI disorders and strengthening the gut. Further insight into the various gut microbes and microbiomes with specific demographic is recommended.

Objective. Political instability, corruption, exclusive institutions et al. are some of the hypotheses backed by literature as to why some nations are more developed than others. One hypothesis which has not been intensively studied is the culpability of individual and institutional behavior and its impact on development. To examine the validity of such a hypothesis, a composite index which quantifies such development hindering behavior must be developed. The prelude to developing this index is to investigate whether such a quantitative measure exists to begin with. To achieve this objective, a bibliometric analysis of Scopus and Web of Science databases will be conducted. Method. A bibliometric and content analysis of Scopus and Web of science databases using Excel, VOSviewer, and R software. Results. The findings of the bibliometric analysis indicate the absence of such measure particularly within the scope of ‘bad behavior’, ‘unethical behavior’, and ‘development’. Conclusions. The study findings provide the greenlight to proceed with the construction of the ‘Bad Behavior Index’. Contribution. The practical contribution of this study is that it provides researchers with an improved methodology on how to conduct a bibliometric analysis to identify the absence of knowledge and provide a justification for the creation of such knowledge by integrating and analyzing two journal databases instead of one, using three mediums: Excel, VOSviewer, and R software.

The experimental verification for the computational method sometimes varies due to numerous factors such as the manufacturing process and the materials' property change due to environmental aspects. In this work, we performed verification of experimental and computational evaluation of a hybrid composite moderate thick plate. The experiment was performed with simplistic approaches and without the advanced tools of preparing composite materials. This is due to the fact that most of the students in many developing countries around the world cannot have access to such equipment. As such, in this research, we are presenting cheap and easy preparation methods, with some details, for even equipment calibration and some tricks to attain a reliable composite structure for educational purposes. Moreover, the software and solvers used in this study are freely provided by the supplier for educational purposes. This study examined two methods for producing carbon and glass/polyester composite plates and discussed which one was best based on mechanical properties for different volume fractions, random stacking sequences, and ply angles (using OCTAVE's random estimation program). It also determined the three natural frequencies experimentally and with the aid of ANSYS. Less than 6% separated the experimentally determined natural frequencies from the calculated results.

Rubber-based composites are widely used especially in transportation. The goal of this paper is to study the mechanical properties of rubber-based composites of carbon black and Nano Aluminum trioxide additive (50 nm). Various percentage of carbon black was used (20,40, and 60 phr). The increase in Carbon black percentage shows an increase in mechanical properties of the composites (for 60 phr properties tensile test improve by 49%, for hardness resistance the improve was 21%, and for the wear test the composite improve by 22%). Various wetting percentage of nano Aluminum trioxide was used (1,1.5,2, and 2.5 %). Increasing the wetting percentage increase tensile strength (27%, hardness resistance increase by 28%, and wear resistance increase nonlinearly with a percentage reaching 70%). Selecting the optimal composition of the two fillers, then study different irradiances for it with the ultraviolet laser of moderately low energy after the vulcanization process. Post ultraviolet laser of (345 nm). Furthermore, laser vulcanization shows improvement in mechanical properties.

Tungsten fibre-reinforced tungsten composites (Wf/W) have been in development to overcome the inherent brittleness of tungsten as one of the most promising candidate for the first wall and divertor armour material in a future fusion power plant. As the development of Wf/W continues, the fracture toughness of the composite is one of the main design drivers. In this contribution the efforts on size upscaling of Wf/W based on Chemical Vapour Deposition (CVD) is shown together with fracture mechanical tests of two different size samples of Wf/W produced by CVD. Three-point bending tests according to ASTM E399 for brittle materials were used to get a first estimation of the toughness. A provisional fracture toughness value of up to 346MPam1/2 was calculated for the as-fabricated material. As the material does not show a brittle fracture in the as-fabricated state, the J-Integral approach based on the ASTM E1820 was additionally applied for this state. A maximum value of the J-integral of 41kJ/m2 (134,8MPam1/2) was determined for the largest samples. Post mortem investigations were employed to detail the active mechanisms and crack propagation.

In the speed control system of Interior Permanent Magnet Synchronous Motor (IPMSM) without a speed sensor, the speed under the traditional PI control suffers from poor tracking performance and step response overshoot. This paper proposes a Compound Variable Structure PI (CVSPI) controller to improve the system control performance. It can choose whether to include an integral term according to the size of the system deviation to speed up the response. It also introduces a Model Reference Adaptive System (MRAS) speed observer in the controller to estimate the speed and adaptively adjust the size of the anti-integration saturation gain to improve the dynamic response following performance and immunity of the system. A feed-forward link is added for a given input differential to achieve an accurate answer to time-varying inputs. As the linear compensation matrix of the conventional MRAS is a unit matrix, the speed can only be accurately observed in a specific speed range. In this paper, a new linear compensation matrix is designed, and a new speed adaptive law is derived, allowing the improved MRAS to measure speed over a wide range accurately. Simulation results validate the excellent control performance of the CVSPI and the accuracy of the enhanced MRAS over a wide speed range.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

For the numerical simulation of components made of short fiber-reinforced composites the correct prediction of the deformation including the elastic and plastic behavior and its spatial distribution is essential. When using purely deterministic modeling approaches the information of the probabilistic microstructure is not included in the simulation process. One possible approach for the integration of stochastic information is the use of random fields. In this study numerical simulations of tensile test specimens are conducted utilizing a finite deformation elastic-ideal plastic material model. A selection of the material parameters covering the elastic and plastic domain are represented by cross-correlated second-order Gaussian random fields to incorporate the probabilistic nature of the material parameters. To validate the modeling approach tensile tests until failure are carried out experimentally, that confirm the assumption of spatially distributed material behavior in both the elastic and plastic domain. Since the correlation lengths of the random fields cannot be determined by pure analytic treatments, additionally numerical simulations are performed for different values of the correlation length. The numerical simulations endorse the influence of the correlation length on the overall behavior. For a correlation length of 5mm a good conformity with the experimental results is obtained. Therefore, it is concluded, that the presented modeling approach is suitable to predict the elastic and plastic deformation of a set of tensile test specimens made of short fiber-reinforced composite sufficiently.

This work investigates how integrated polyimide inlays with applied sensor bodies influence the guided ultrasonic wave propagation in narrow glass fiber-reinforced polymer specimens. Preliminary numerical simulations indicate that in a damping-free specimen, the inlays show reflections for the S0-mode propagation. Hence, an air-coupled ultrasonic technique and a 3D laser Doppler vibrometer measurement are used to measure different parts of the propagating waves’ displacement field after burst excitation at different frequencies. No significant reflections on the inlay can be seen in the experiments. However, it is shown that the reflections from the strip specimen’s narrow width cause periodical reflections that superimpose with the excited wave fronts. A continuous wavelet transformation in the time-frequency domain filters discontinuities from the measurement signal and is used for reconstruction of the time signals. The reconstructed signals are used in a spatial continuous wavelet transformation to identify the occurring wavelengths and hence to prove the assumption of reflections from the narrow edges. Since the amplitude of the reflections identified in the numerical data at the polyimide inlays are an order of magnitude smaller than the excited wave packages, it is concluded that material damping of the epoxy resin matrix extincts possible reflections from the inlays.

In the speed control system of Interior Permanent Magnet Synchronous Motor (IPMSM) without a speed sensor, the speed under the traditional PI control suffers from poor tracking performance and step response overshoot. This paper proposes a Compound Variable Structure PI (CVSPI) controller to improve the system control performance. It can choose whether to include an integral term according to the size of the system deviation to speed up the response. It also introduces a Model Reference Adaptive System (MRAS) speed observer in the controller to estimate the speed and adaptively adjust the size of the anti-integration saturation gain to improve the dynamic response following performance and immunity of the system. A feed-forward link is added for a given input differential to achieve an accurate answer to time-varying inputs. As the linear compensation matrix of the conventional MRAS is a unit matrix, the speed can only be accurately observed in a specific speed range. In this paper, a new linear compensation matrix is designed, and a new speed adaptive law is derived, allowing the improved MRAS to measure speed over a wide range accurately. Simulation results validate the excellent control performance of the CVSPI and the accuracy of the enhanced MRAS over a wide speed range.

Bonding agents (BA) are key compounding ingredients for the correct formulation of composite solid rocket propellants (CSRP). In particular, the addition of BA is essential to achieve suitable mechanical properties of CSRP in terms of adequate tensile strength and elongation at break. It is shown that the polarity of each conventional BA as well as new potential BA can be measured through the Reichardt’s ET(30) polarity scale. Using this criteria it was possible to find a substitute for MAPO (tris-(methylaziridinyl)-phosphine oxide), a conventional BA with the drawback of high toxicity and high reactivity, with TTPT (tris-(pyrrolidine)-phosphine oxide), a completely safe and effective BA. In this work, many other potential BA were evaluated through the Reichardt’s ET(30) polarity scale but only a selection of the potential BA were effectively tested in a standard CSRP. Particular interesting was the evaluation of TTPT vs MAPO showing the ability of the former BA to match the mechanical properties of the latter BA.

We present an integrable, sensor inlay for monitoring crack initiation and growth inside bondlines of structural carbon fiber reinforced plastic (CFRP) components. The sensing structures are sandwiched between crack stopping polyvinyliden fluoride (PVDF) and a thin reinforcing polyetherimide (PEI) layer. Good adhesion at all interfaces of the sensor system and to the CFRP material is crucial as weak bonds can counteract the desired crack stopping functionality. At the same time, the chosen reinforcing layer must withstand high strains, safely support the metallic measuring grids and possess outstanding fatigue strength. We show that this robust sensor system, which measures the strain at two successive fronts inside the bondline, allows to recognize cracks in the proximity of the inlay regardless of the mechanical loads. Feasibility is demonstrated by static load tests as well as cyclic long-term fatigue testing with up to 1,000,000 cycles. In addition to pure crack detection, crack distance estimation based on sensor signals is illustrated. The inlay integration process is developed with respect to industrial applicability. Thus, implementation of the proposed system will allow the potential of lightweight CFRP constructions to be better exploited by expanding the possibilities of structural adhesive bonding.

Spinal Cord Stimulation (SCS) is an effective and validated treatment to address chronic refractory neuropathic pain in Persistent Spinal Pain Syndrome-Type 2 (PSPS-T2) patients. Surgical SCS lead placement is traditionally performed under general anesthesia due to its invasiveness. In parallel, recent works have suggested that Awake Anesthesia (AA), consisting in Target Controlled Intra-Veinous Anesthesia (TCIVA), could be an interesting tool to optimize lead anatomical placement using patient intra-operative feedback. We hypothesized that combining AA with Minimal Invasive Surgery (MIS) could improve SCS outcomes. The goal of this study was to evaluate SCS lead performance (defined by the area of pain adequately covered by paraesthesia generated via SCS), using an intraoperative objective quantitative mapping tool, and secondarily to assess pain relief, functional improvement and change in quality of life with a composite score. We analyzed data from a prospective multicenter study (ESTIMET) to compare the outcomes of 115 patients implanted with MIS under AA (MISAA group) or General Anesthesia (MISGA group), or by Laminectomy under General Anesthesia (LGA group). All in all, MISAA appears to show significantly better performance in terms of patient pain coverage, as well as improved secondary outcomes. One step further, our results suggest that MISAA combined with intra-operative hypnosis could potentialize patient intraoperative cooperation and could be proposed as a personalized package offered to PSPS-T2 patients eligible for SCS implantation in highly dedicated neuromodulation centers.

Li4Ti5O12 (LTO) exhibits zero-strain behavior, exceptional cycle stability, low cost, and high safety. However, it is still low in electronic and ionic conductivity. Incorporating Sn into LTO materials can increase electronic conductivity and specific capacity. However, Sn still experiences volumetric expansion during the charging/discharging process. Adding activated carbon (AC) into the LTO/Sn composite can help improve the expansion resistance and electronic conductivity. In this work, the AC was first synthesized from charcoals through the carbon activation process and mixed with LTO precursors through the sol-hydrothermal method followed by mixing with Sn through the mechanochemical process to produce LTO@AC/Sn composites. The Sn content was fixed at 15 wt.%, while the AC contents were varied at 1 wt.%, 3 wt.%, and 5 wt.%. The AC specific surface area is increased by more than 100% compared to the non-activated one. The best effects of AC on grain morphology and distribution were found in the LTO/Sn contained 3 wt.% of AC, leading to transfer resistance, ohmic resistance, specific capacity, and coulombic efficiency were found to be 48.1 Ω, 8.5 Ω, 138 mAhg-1, and near 100%, respectively. The result suggests that the LTO@AC/Sn could be a favorable anode active material in lithium-ion batteries.

Background: Physical activity has been considered as a promising approach to slow down the disease process in Multiple Sclerosis (MS) patients. While the functional impairments of MS have been studied in detail, but there is limited evidence of the efficacy of exercise interventions on the Multiple Sclerosis functional composite (MSFC) score in these patients. The study aim was to in-vestigate the improvement in MSFC score by multi-function swing suspension training (MFSST) in the women with MS. Methods: The patients were divided into the intervention and control groups. A total of 47 MS patients completed the MSFC components at baseline and after the intervention. Z scores were created for each test based on control means. Results: The MSFC components showed a significant increment in comparison with the baseline levels in the four, six, and eight weeks following the first exercise session (all p<0.05). These dif-ferences in the control group were not significant. The improvement in the MSFC score and the component Z-scores in the intervention groups was found from the fourth week onwards. Conclusions: The study findings highlight that MFSST can be used as an effective treatment method in MS patients due to its positive effects on physical parameters, such as muscles strength, functional impairments, and cognitive problems.

Under batch experiment conditions, this work seeks to successfully remove Diclofenac-Na (DCF-Na) from an aqueous solution utilizing a composite sorbent made of Bentonite, Kaolinite clay, and Worm casting (BKW). This study investigated the structural modification of the H₃PO₄ Modified Clay by X-ray fluorescence and the effect of selected adsorption factors – DCF-Na concentration and modified BKW composite dosage. The concentration equilibrium data was used to study six isotherm models. Freundlich isotherm model better explained the adsorption of DCF-Na onto modified BKW composite with a correlation coefficient close to 1. Kinetics models were examined, and the Elovich model gave a better fit than other kinetic models studied. Mass diffusion mechanisms and thermodynamics studies were successfully carried out. The enthalpy change values evaluated were negative, which revealed the spontaneity of DCF-Na remediation onto modified BKW, and that DCF-Na adsorption is exothermic and occurred through a physisorption process.

Agricultural wastes have posed as a treat to the environment over the years and they are found in large quantities due to domestic and industrial utilization of such materials in under developed and developing countries. The inability to recycle this waste has led to researches on how to use them in carrying out productive industrial activities. The aim of this study is to use Central Composite Design (CCD) to optimize the bleaching effects by snail shell as adsorbents on crude palm oil. The predictive ability of the model was close to accurate using MINITAB 19 software with the design application for the process simulation for % FFA yield to have 75.856% for experimental and 77.587% for predicted yield with just 1.731% residual. The saponification value increased with adsorption, and it indicates that palm oil can be used for soap making.

In this research, Cellulose Nanofibers (NFC) modified with a eutectic of lauric acid (LA) was prepared as a new form-stable phase change material (NFC-LA). Thermal properties of this composite were investigated by Differential Scanning Calorimetry (DSC). The results revealed that the melting temperature and latent heat of NFC/LA were 21.56 °C and 88.5 J/g, respectively; and the super cooling degree for the NFC-LA composite decreased to 13.99 °C when compared to 20.28 °C of the pure lauric acid. Natural clay was purified and modified with Cetyltrimethyl ammonium bromide (CTAB) to prepare organoclay. Through FTIR spectra, we have confirmed that the clay was successfully modified. The PCM-composite was then added to the organoclay to obtain a new composite denoted NFC-LA-OC. this latter was added to cement and was investigated as a reinforcement material in cement mortars for thermal energy storage application. The prepared material can both solve the leakage problem associated to the phase change material, and reduce or even avoid the use of heating and air conditioning systems, which are energy-intensive systems, and therefore reduce energy consumption.

L-asparaginase (ASNase) is an aminohydrolase currently used in the pharmaceutical and food industries. Enzyme immobilization is an exciting option for both applications, allowing a more straightforward recovery and increased stability. High surface area and customizable porosity make carbon xerogels (CXs) promising materials for ASNase immobilization. This work describes the influence of contact time, pH, and ASNase concentration on the immobilization yield (IY) and relative recovered activity (RRA) using Central Composite Design methodology. The most promising results were obtained using CX with an average pore size of 4 nm (CX-4), reaching IY and RRA of 100%. At the optimal conditions, the ASNase-CXs biocomposite was characterized and evaluated in terms of kinetic properties and operational, thermal and pH stabilities. The immobilized ASNase onto CX-4 retained 71% of its original activity after six continuous reaction cycles, showed a good thermal stability at 37 °C (RRA of 91% after 90 min) and was able to adapt to both acidic and alkaline environments. Finally, the results indicated a 3.9-fold increase in the immobilized ASNase affinity for the substrate, confirming the potential of CXs as a support for ASNase and as a cost-effective tool for subsequent use in the therapeutic and food sectors.

The extrusion-based 3D concrete printing (3DCP) technology allows the fabrication of permanent formwork with intricate shapes, into which fresh concrete is cast to build structural members with complex geometry. This significantly enhances the geometric freedom of concrete structures without the use of expensive temporary formwork. In addition, with proper material choice for the permanent formwork, the load-bearing capacity and durability of the resulting structure can be improved. This paper investigates 3DCP of permanent formwork for reinforced concrete (RC) beam construction. A 3D-printable engineered geopolymer composite (3DP-EGC, or strain-hardening geopolymer composite, 3DP-SHGC) recently developed by the authors was used for fabrication of the permanent formwork. The 3DP-EGC exhibits strain-hardening behaviour under direct tension. Two different printing patterns were used for the soffit of the permanent formwork to investigate the effect of this parameter on the flexural performance of RC beams. A conventionally mould-cast RC beam was also prepared as the control beam for comparison purposes. The results showed that the RC beams constructed using the 3DP-EGC permanent formwork exhibited superior flexural performance to the control beam. Such beams yielded significantly higher cracking load (up to 43%), deflection at ultimate load (up to 60%), ductility index (50%) and absorbed energy (up to 107%) than those of the control beam. The ultimate load was comparable with or slightly higher than that of the control beam. Furthermore, the printing pattern at the soffit of the permanent formwork was found to have a significant influence on the flexural performance of the RC beams.

One of the major limitations of the current 3D-concrete-printing technology is incorporation of reinforcement. Furthermore, there is a need to decrease the ecological footprint of printable concrete. As a possible solution for these challenges, this paper presents a 3D-printable strain-hardening geopolymer composite (3DP-SHGC) that shows pseudo-ductile behaviour under direct tension. The developed 3DP-SHGC is composed of one-part (just-add-water) geopolymer binder made of slag (GGBFS), fly ash (FA) and solid activator. The one-part geopolymer binder eliminates the need for elevated temperature curing and handling of corrosive alkaline liquids. At first, an optimum matrix was identified by studying the effects of FA to GGBFS ratio on the rheological properties and compressive strength. Subsequently the optimum matrix was reinforced by PVA fibres to make the 3DP-SHGC, which printing performance and rheological properties were evaluated. In addition, the influences of curing temperature on the compressive, flexural and tensile performances of the printed specimens were also investigated. The results were compared with those obtained for the mould-cast specimens. The 3DP-SHGC exhibited superior flexural performance, higher tensile strength, and comparable tensile strain capacity to the mould-cast counterpart. Further, the curing temperature had influence on the mechanical properties of both 3D-printed and mould-cast SHGCs. The underlying reasons for the differences are discussed.

The dynamic effects observed in collisions represent a specific area of high-energy interaction located at the boundary of mechanics, hydrodynamics, shock wave physics, and alternating high-pressure regions. The paper shows that in the volume of a solid metal body, as a result of dynamic alloying by a high-speed stream of powder particles in the super-deep penetration mode (SDP), fibre structures of altering material arise, forming the framework of the composite material. The stream of powder particles in the metal obstacle following the path of least resistance and the impact of shock waves on particles results in a volumetric framework from the products of interaction between the injected and matrix materials. When using SDP, defective structural elements (channelled) - germs of reinforcing fibres arise. At the subsequent heat treatment, there is an intensive diffusion. The growth process of reinforcing fibres shifts to higher temperatures (as compared to the standard mode), leading to an increase in the bending strength of the fibre material up to 13 times for high-speed tool W6Mo5Cr4V2 steel. As a result of the completion of the growth of reinforcing fibres in the volume of the W6Mo5Cr4V2 steel, the material's bending strength in 1.2 times is realised. Simultaneously, it provides an increase of wear resistance 1.7-1.8 times.

Decades ago, when computational was expensive and limited, the structural design was mostly performed by hand calculations using simple mathematical models. For example, it was a common practice to design a structure as complex as the wing of an aircraft by simple beam analysis. However, ever since the classic paper by Turner et al., due to a rapid increase in computational, more complex mathematical models are being used to simulate the physical behavior of complex structural components. To solve intractable problems unsolvable by hand calculations, numerical techniques like Finite Element Analysis (FEA), Computational Fluid Dynamics (CFD), Finite Difference Method etc. are being employed. In fact, the availability of these methods has led to the development of an entirely new area of research known as Multidisciplinary Design Optimization (MDO) where various disciplines are considered in an optimization problem. The most important question while using a mathematical model to represent practical industrial problems is to what extent these models represent the real-life situation. Computational models are always built on upon assumptions. Simply at looking at the simulation outcomes i.e. the graphical and numerical results, it is often very difficult to ensure if the underlying assumption holds and that the results are reliable. This has led to the development of another field of research known as Verification and Validation (called V&V in short).

Among the various methods for collecting oil spills and oil products, including from the water surface, one of the most effective is the use of sorbents. In this work, three-component bio-based composite granular adsorbents were produced and studied for oil products pollution collection. A bio-based binder made of peat, devulcanised crumb rubber from used tyres, and part fly ash as cenospheres were used for absorbent production. The structure, surface morphology, porosity, mechanical properties, and sorption kinetics of the obtained samples were studied. Composite hydrophobicity and sorption capacity to oil products such as diesel fuel (DF) and motor oil (MO) were determined. The obtained pellets are characterised by a sufficiently pronounced ability to absorb oil products such as DF. As the amount of CR in the granules increases, the diesel absorption capacity increases significantly. The case of 30-70-0 is almost 3 times higher than the granules from homogenised peat. The increase in q is due to two factors: pronounced surface hydrophobicity of the samples (Θ = 152°) and a heterogeneous porous granule structure. The presence of the cenosphere in the biocomposite reduces its surface hydrophobicity while increasing the diesel absorption capacity. Relatively rapid realisation of the maximum saturation by the MO was noted. In common, the designed absorbent shows up to 0.7 g·g^-1 sorption capacity for MO and up to 1.55 g·g^-1 sorption capacity for diesel. A possible mechanism of DF absorption and the limiting stages of the process approximated for different kinetic models are discussed. The Weber-Morris diffusion model is used to primarily distinguish the limiting effect of external and internal diffusion of adsorbate on the absorption process

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

Integer is either a composite number or a prime number. Therefore, detecting composite numbers is important for solving prime numbers. The study of prime numbers, apart from satisfying human curiosity, can be very important. In this article, the order of composite numbers has been detected. And explained with a simple method and a simple function. And, a method has been developed in which all composite numbers and therefore prime numbers can be determined by using the specified methods, functions and formulas.

The paper presents section models for analysis of the resistance of RC members subjected to bending moment with or without axial force. To determine the section resistance the nonlinear stress-strain relationship for concrete in compression is assumed, taking into account the concrete softening. It adequately describes the behavior of RC members up to failure. For the reinforcing steel linear elastic-ideal plastic model is applied. For the ring cross-section subjected to bending with axial force the normalized resistances are derived in the analytical form by integrating the cross-sectional equilibrium equations. They are presented in the form of interaction diagrams and compared with the results obtained by testing conducted on RC columns under eccentric compression. Furthermore, the ultimate normalized bending moment has been derived for the rectangular cross-section subjected to bending without axial force. It was applied in the cross-sectional analysis of steel and concrete composite beams, named BH beams, consisting of the RC rectangular core placed inside a reversed TT welded profile. The comparisons made indicated good agreements between the proposed section models and experimental results.

The aroused quest to reduce the delay at interconnect level is the main urge of this paper to come across a configuration of Carbon Nanotube (CNT) bundle namely squarely packed bundle of composite CNTs. The approach, demonstrated in this paper, adapts the composite bundle to adopt for high speed Very Large Scale Integration (VLSI) interconnect with technology sizing down. To reduce the delay of the proposed configuration of composite CNT bundle, the behavioral change of Resistance (R), Inductance (L) and Capacitance (C) has been observed with respect to both width of the bundle and diameter of the CNTs in the bundle. Consequently, the performance of the modified bundle configuration is compared with previously developed configuration namely squarely packed bundle of dimorphic MWCNTs in terms of propagation delay and crosstalk delay at local, semiglobal and global level interconnect. The proposed bundle configuration is ultimately enacted as better one for 32nmand 16nmtechnology node and suitable for 7nmas well.

The total amount of greenhouse gas emissions directly or indirectly generated by thermal power enterprises at any given time can be offset through afforestation, energy conservation and emission reduction. The present situation and control methods of CO₂ emission in China's coal-fired thermal power industry are introduced. The complex ecosystem is a unity of ecological functions composed of human society, economic activities and natural conditions. In the context of carbon neutrality and based on the theory of composite ecosystem, this paper divides the coal-fired thermal power plants in China into environmental management zones, calculates the atmospheric environmental capacity, and puts forward the concept of regional atmospheric environmental capacity, classification and zoning control. Finally, the management and control units are classified, and differentiated management and control requirements are put forward to provide a reference for regional air quality standard planning.

This work shows a correlation between light reflectance, absorption, and morphologies of series of (1-x) BM–x PT, (x = 0.0, 0.02, 0.04, 0.08, 0.12, 0.16, 0.24) ceramics composite. The (1-x) BM–x PT showed features of a black mirror with a low optical energy gap. The measured Vis-NIR diffused reflectance enabled the calculation of the energy gap using the modified Kubelka-Munk function. The estimated energy gap was lower than 1.5 eV related to low reflectance in the Vis-NIR range. Moreover, obtained histograms of grains, using scanning electron microscope, enabled the correlation between grains size and amount of lead titanate. We deduced from the ceramics surface morphology that marked porosity also induced reflectivity of low magnitude. We correlated the magnitude of the energy gap with phases of the BM-PT composite and with the electrical conductivity activation energy reported in the literature. Our results findings opened prospect studied materials for optical applications.

A deep relationship is identified between the Coulomb Force and Gravity. A gravitational constant for strong gravity is calculated from the relationship. The equivalence between mass and charge is explored. Implications are given for the expansion of Einstein's Field Equations to include vector gravity.

Concerns associated with global warming and the depleting reserves of fossil fuels have highlighted the importance of high-performance energy storage systems (ESSs) for efficient energy usage. ESSs such as supercapacitors can contribute to improved power quality of an energy generation system, which is characterized by a slow load response. Composite materials are primarily used as supercapacitor electrodes because they can compensate for the disadvantages of carbon or metal oxide electrode materials. In this study, a composite of oxide nanoparticles loaded on a carbon nanofiber support was used as an electrode material for a hybrid supercapacitor. The addition of a small amount of hydrophobic Fe- and N-doped graphene nanoplates modified the surface properties of carbon nanofibers prepared by electrospinning. Accordingly, the effects of the hydrophobic/hydrophilic surface properties of the nanofiber support on the morphology of Co3O4 nanoparticles loaded on the nanofiber, as well as the performance of the supercapacitor, were systematically investigated.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

Assuming a two component, positive and negative mass, superfluid/supersolid for space (the Winterberg model), we model the Higgs field as a condensate made up of a positive and a negative mass, planckion pair. The connection is shown to be consistent (compatible) with the underlying field equations for each field, and the continuity equation is satisfied for both species of planckions, as well as for the Higgs field. An inherent length scale for space (the vacuum) emerges, which we estimate from previous work to be of the order of,

Many combinatorial optimization problems are hard to solve within the polynomial computational time or NP-hard problems. Therefore, developing new optimization techniques or improving existing ones still grab attention. This paper presents an improved variant of the Ant Colony Optimization meta-heuristic called Enhanced Hyper Cube Framework ACO (EHCFACO). This variant has an enhanced exploitation feature that works through two added local search movements of insertion and bit flip. In order to examine the performance of the improved meta-heuristic, a well-known structural optimization problem of laminate Stacking Sequence Design (SSD) for maximizing critical buckling load has been used. Furthermore, five different ACO variants were concisely presented and implemented to solve the same optimization problem. The performance assessment results reveal that EHCFACO outperforms the other ACO variants and produces a cost-effective solution with considerable quality.

The multidimensionality of chronic pain forces us to look beyond isolated pain assessment such as pain intensity, which does not consider multiple key parameters, particularly in patients suffering from post-operative Persistent Spinal Pain Syndrome (PSPS-T2). Our ambition was to provide a novel Multi-dimensional Clinical Response Index (MCRI), including not only pain intensity but also functional capacity, anxiety-depression, quality of life and objective quantitative pain mapping assessments, the objective being to capture patient condition instantaneously, using machine learning techniques. Two hundred PSPS-T2 patients were enrolled in a real-life observational prospective PREDIBACK study with 12-month follow-up and received various treatments. From a multitude of questionnaires/scores, specific items were combined using exploratory factor analyses to create an optimally accurate MCRI; as a single composite index, using pairwise correlations between measurements, it appeared to better represent all pain dimensions than any other classical score. It appeared to be the best compromise among all existing indexes, showing the highest sensitivity/specificity related to Patient Global Impression of Change (PGIC). Novel composite indexes could help to refine pain assessment by changing the physician’s perception of patient condition on the basis of objective and holistic metrics, and by providing new insights to therapy efficacy/patient outcome assessments, before ultimately being adapted to other pathologies.

The analysis and measurement of poverty is a crucial issue in the field of social science. Poverty is a multidimensional notion that can be measured using composite indicators relevant to synthesizing statistical indicators. Subjective choices could, however, affect these indicators. We propose interval-based composite indicators to avoid the problem, enabling us in this context to obtain robust and reliable measures. Based on a relevant conceptual model of poverty we have identified, we will consider all the various factors identified. Then, considering a different random configuration of the various factors, we will compute a different composite indicator. We can obtain a different interval for each region based on the distinct factor choices on the different assumptions for constructing the composite indicator. So we will create an interval-based composite indicator based on the results obtained by the Monte-Carlo simulation of all the different assumptions. The different intervals can be compared, and various rankings for poverty can be obtained. For their parameters, such as center, minimum, maximum, and range, the poverty interval composite indicator can be considered and compared. The results demonstrate a relevant and consistent measurement of the indicator and the shadow sector's relevant impact on the final measures.

The non-linear analysis of hollow-core concrete slabs requires the use of advanced numerical techniques, proper constitutive models both for concrete and steel as well as particular computational skills. If prestressing, cracking, crack opening, material softening, etc. are also to be taken into account, then the computational task can far exceed the capabilities of an ordinary engineer. In order for the calculations to be carried out in a traditional design office, simplified calculation methods are needed. Preferably based on the linear finite element (FE) method with a simple approach that takes into account material nonlinearities. In this paper the simplified analysis of hollow-core slabs based on the generalized nonlinear constitutive law is presented. In the proposed method a simple decomposition of the traditional iterative linear finite element analysis and the non-linear algebraic analysis of the plate cross-section is used. Through independent analysis of the plate cross-section in different deformation states, a degraded plate stiffness can be obtained, which allows iterative update of displacements and rotations in the nodes of the FE model. Which in turn allows to update the deformation state and then correct translations and rotations in the nodes again. The results obtained from the full detailed 3D nonlinear FEM model and from the proposed approach are compared for different slab cross-sections. The obtained results from both models are consistent.

Typhoid fever is a major public health burden which causes substantial global morbidity and mortality due to lack of decisive diagnostic protocols. The capacity of commonly use diagnostic test to validate the absence of typhoid fever is controversial. This study explores to evaluate new techniques for typhoid diagnosis and proposed a harmonised suitable standardized composite reference to be adopted. Published peer-reviewed articles indexed in PubMed, MEDLINE and Google scholar were reviewed for hospital-based studies. This study reveals new typhoid diagnostic techniques such as proteomics, serology, Rapid Diagnostic tests (RDTs), transcriptomics, genomics, and metabolomics. 34.4% of the studies use prospective study design. The study result establishes that, Widal test has a moderate diagnostic accuracy with average percentage sensitivity (52.9%), specificity (54%), positive predictive value (PPV) (56.8%) as well as negative predictive value (NPV) (55.6%) when compared with 29.4%, 28%, 29.5%, and 27.8% of Typhidot respectively. The findings showed a statistically significant difference on the sensitivity between Widal and Typhidot t (40) = 2.639, p = 0.012 at p<0.05 using independent sample t-test. When there is no perfect reference standard that has an optimal diagnostic accuracy, the need for a harmonised suitable standardized composite reference is essential. Hence, this study recommends that, peripheral blood culture with established sensitivity of 60% and Widal test with average sensitivity of 52.9% be adopted as a consensus composite reference standard for typhoid fever diagnosis in other to improve confidence in prevalence estimates.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

The present work aims to characterize the mechanical behavior of a new composite material for the conservation and development of the vast historical and architectural heritage that is particularly vulnerable to environmental and seismic actions. The new composite consists of natural hydraulic lime (NHL) -based mortar, reinforced by sisal short fibers randomly oriented in the mortar matrix. The NHL-based mortar ensures the chemical-physical compatibility with the original feature of the historical masonry structures (mostly in stone and clay) aiming to pursue both the effectiveness and durability of the intervention. The use of vegetable fibers (i.e. the sisal one) is an exciting challenge for the construction industry since they require a lower degree of industrialization for their processing, and therefore, their costs are also low, as compared to the most common synthetic/metal fibers. Beams of sisal-composite sizing 160x40x40 mm3 with a central notch are tested in three-point bending, aiming to evaluate both their bending strength and fracture energy. Also, tensile tests and compressive tests were performed on the composite samples, while water retention test and slump test were performed on the fresh mix. Finally, the tensile tests on the Sisal strand were carried out to evaluate the tensile strength of both strand and wire. A final comparison with unreinforced mortar specimens shows that the proposed composite ensures great workability and good performances in term of ductility and strength and it can be considered a promising alternative to the classic fiber-reinforcing systems.

Poor understanding of malnutrition burden is a common reason for not prioritizing the care of small and nutritionally at-risk infants aged under-six months (infants u6m). We aimed to estimate the anthropometric deficit prevalence in infants u6m attending health centres, using the Composite Index of Anthropometric Failure (CIAF); and to assess the overlap of different individual indicators. We undertook a two-week survey of all infants u6m visiting each of 18 health centres in two zones of the Oromia region, Ethiopia. We measured weight, length, and MUAC (Mid upper arm circumference); and calculated weight-for-length (WLZ), length-for-age (LAZ), and weight-for-age z-scores (WAZ). Overall, 21.7% (95% CI: 19.2; 24.3) of infants u6m presented CIAF and of these, 10.7% (95% CI: 8.93; 12.7) had multiple anthropometric deficits. Low MUAC overlapped with 47.5% (95% CI: 38.0; 57.3), 43.8% (95% CI: 34.9; 53.1), and 42.6% (95% CI: 36.3; 49.2) of the stunted, wasted and CIAF prevalence, respectively. Underweight overlapped with 63.4% (95% CI: 53.6; 72.2), 52.7% (95% CI: 43.4; 61.7), and 59.6% (95% CI: 53.1; 65.9) of the stunted, wasted and CIAF prevalence, respectively. Anthropometric deficits, single and multiple, are prevalent in infants attending health centres. WAZ overlaps more with other forms of anthropometric deficits than MUAC.

In this study, grit blasting pretreatment was used to improve the adhesion and corrosion resistance and microhardness of Ni-W/SiC nanocomposite coatings fabricated using conventional electrodeposition technique. Prior to deposition, grit blasting and polishing (more commonly used) pretreatment were used to prepare the surface of the substrate and the 3D morphology of the pretreated substrates was characterized using laser scanning confocal microscopy. The coatings surface and the cross section morphology were analyzed using scanning electron microscopy (SEM). The chemical composition, crystalline structure, microhardness, adhesion, and the corrosion behavior of the deposited coatings were characterized using energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), microhardness tester, scratch tester and electrochemical workstation, respectively. The results indicated that the grit blasting and SiC addition, improved the microhardness, adhesion and corrosion resistance. The Ni-W-SiC nanocomposites pretreated by grit blasting exhibited the best adhesion strength, up to 36.5 ± 0.75 N. Its hardness was the highest and increased up to 673 ± 5.47Hv and its corrosion resistance was the highest compared to the one pretreated by polishing.

The paper presents a modified finite element method for nonlinear analysis of 2D beam structures. To take into account the influence of the shear flexibility, a Timoshenko beam element was adopted. The algorithm proposed enables using complex material laws without the need of implementing advanced constitutive models in finite element routines. The method is easy to implement in commonly available CAE software for linear analysis of beam structures. It allows to extend the functionality of these programs with material nonlinearities. By using the structure deformations, computed from the nodal displacements, and the presented here generalized nonlinear constitutive law, it is possible to iteratively reduce the bending, tensile and shear stiffnesses of the structures. By applying a beam model with a multi layered cross-section and generalized stresses and strains to obtain a representative constitutive law, it is easy to model not only the complex multi-material cross-sections, but also the advanced nonlinear constitutive laws (e.g. material softening in tension). The proposed method was implemented in the MATLAB environment, its performance was shown on the several numerical examples. The cross-sections such us a steel I-beam and a steel I-beam with a concrete encasement for different slenderness ratios were considered here. To verify the accuracy of the computations, all results are compared with the ones received from a commercial CAE software. The comparison reveals a good correlation between the reference model and the method proposed.