CSZM compounds were synthesized by dry chemistry route with 5, 10, and 15% dopant of Mg dopants in the Ce 0.8-2x Sm 0.2 Zrx Mgx O2-d, {x = 0.05, 0.1 &0.15}. The newly investigated materials were physically, chemically, and electrochemically studied and have shown promising results. The CSZM was crystalized in a fluorite structure with a pure cubic phase in a space group Fm3m and cell parameter a = 5.401742 °A and theoretical density from 7.6 to 8.9 after firing in the air with a final temperature of 1400 °C. characterization of the structure and indexing of electrolyte materials were made after X-ray diffraction (XRD) testing. A Scanning electron microscope (SEM) morphological analysis was used to examine the microstructure details. Electronic impedance spectroscopy (EIS) measurements were achieved from 400 °C to 700 °C showing the highest value of conductivity of 1.0461 x 10+1 S/cm at 700 °C while the minimum value was 2.7329 x 10-2 S/cm at 400 °C and the total activation energy was found (Ea) 0.6865 eV under 5% H2/Ar.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

Several methods of processing wood into strong, durable products for the construction industry provide transformative opportunities to substitute for less sustainable building materials. Carbon storage is a further advantage, with the added possibility of combustion for bioenergy at end of life. Intense research activity in this area is expected to open up new markets for wood fiber during the lifetime of trees now being planted. Here, wood-derived materials are classified according to the particle size, from metres to nanometres, into which the wood is fragmented before reconstitution. Materials made by densifying or chemically modifying solid wood with no fragmentation are already in production for exterior doors, window frames and cladding, with improved uniformity and stability compared with unmodified wood. Pre-commercial developments promise further gains in durability and strength. Emerging developments extend these process technologies to wood that has been chipped or stranded or pulped, retaining the above advantages over raw timber for weather-facing applications and adding processability by moulding or extrusion. Crucially, the raw material does not then need to be sawn timber but can be bioenergy-grade wood biomass. This will facilitate afforestation strategies that combine the aims of carbon sequestration and biodiversity.

The EU has set the ambitious target of raising the share of EU energy consumption produced from renewable resources to 32% by 2030 with a target of climate neutrality by 2050. The aim of this paper is to assess the role of biomass usage in the context of these targets. The paper identifies progress made between 2013–2022 by focusing on a selection of EU countries. The largest bio-energy increments of 130PJ, 77PJ and 60PJ were reported for Poland, Sweden, and the Nether-lands. This study valuates the crucial role in co-generation and heat in EU regions, with biomass usage between 55-80% of the combined heat and power (CHP) energy in Nordic countries. The future perspectives for bioenergy based on EU policies, biomass resources and technical issues were addressed. The EU possess around 9% of the global biomass supply, ensuring a certain level of biomass resource dependence. Thus, the biomass usage demand in energy production, non-energy sectors and transport is expected to rise leading to increments of 13%-76% on biomass imports. It appears that bioenergy development is mostly limited by economic issues and uneven support for bioenergy in different EU countries as well as environmental issues. The study shows a promising and sustainable potential of bioenergy in the EU as a renewable energy source while minimizing negative impacts on the environment and the economy. By 2050, liquid biofuels are likely to be increasingly used in the transport sector. Non-energy sector usage of biomass is still in an early stage of development, except for the pulp and paper industry, and significant use of biomass in non-energy sectors seems unlikely in the near future.

High-quality rice (Oryza sativa L.) is increasingly widely planted in China with the improvement of people's living standards and the achievement of rice breeding efforts in recent years. However, the agronomic and physiological performances of high-quality indica rice (HQIR) under different nitrogen(N) application conditions in southern China are little known. Two-year consecutive field experiments were conducted with two HQIR and two ordinary-quality indica rice (OQIR) varieties under moderate and high N application rates, with yield and yield components, biomass, N up-take, and their related traits investigated. We found that grain yields of HQIR were slightly de-creased, but grain yields of OQIR were significantly increased by 6.60%-8.88% under high N rate compared with moderate N rate in both years. Thereby, OQIR produced 8.34%-11.87% and 22.00%-22.50% higher grain yield than HQIR under moderate and high N rates, respectively. The different responses of grain yield to N application rates were mainly due to decreased grain set-ting rate in HQIR and increased spikelets m-2 in OQIR under high N rate. Furthermore, high N rate significantly reduced pre-anthesis AE and improved grain-leaf area ratio, while did not in-crease post-anthesis DM compared with moderate N rate in HQIR, which might result in carbon metabolic deterioration and imbalance of source-sink relationship and subsequently lower supply of carbohydrate to panicle. Our results suggest that a moderate N rate (165 kg N ha-1) is beneficial for HQIR varieties to balance the maximum grain yield and high quality in southern China

Brewers’ spent grain (BSG) is an important waste produced in beer companies with a high po-tential to be transformed into commercial by-products. The present paper reports a forecasting technology study with the aid of bibliographic review and patent analysis tools aiming to in-vestigate the maturity of certain technologies, considering the use of BSG on a closed-loop bio-refinery and circular bioeconomy concept integrated into a brewery. To evaluate the possibili-ties of production of high-added value products in Brazil, it was presented an overview of BSG’s scientific, technological, and marketing products and applications. The comparison between numbers of articles versus patents shows that the solutions proposed by research articles are not being transformed into maturated viable technologies. The results suggest that there is a gap between the scientific research in the institutions and their applications in industry, which lead to the destination of the BSG for more economically attractive investments when compared to research in Brazil. Ultimately, from the carried-out analysis, it was possible to propose a brew-ing process connected to the biorefinery system, showing the possibility to the newly arising brewery industries.

Plant roots have significant effects on the soil erosion rates, since they can strongly change the soil detachment capacity (Dc). This study quantifies Dc at different flow rates in soils with Alnus subcordata species, compared to three other species (Brachythecium plumose, Gleditsia caspica and Sambucus ebulus species) in the Saravan forest park and develops regression equations for predicting Dc. Undisturbed samples collected from soils with the four tree species and subjected to five slopes (from 4.3 to 38.3%) and five water discharges (from 0.28 to 0.71 l m−1 s−1) using a hydraulic flume. The results showed that Dc was significantly lower in soils with Alnus subcordata species compared to Brachythecium plumose, Gleditsia caspica and Sambucus ebulus species, as the consequence of the changes in the root characteristics, so that Dc was negatively correlated with root weight density, root length and root biomass. The unit stream power had high accuracy for predicting Dc for all of the studied species. The lowest value of rill erodibility (Kr) was obtained in soils with Alnus subcordata species using regression relationship between the Dc and the shear stress of the soil. This experiment helped to show the importance of plant roots in reducing the soil detachment rates and provided a contribution in understanding the choice of appropriate species for soil conservation.

In the face of the current energy and environment problems, the full use of biomass resources instead of fossil energy to produce a series of high-value chemicals has great application prospects. 5-hydroxymethylfurfural (HMF), which can be synthesized from lignocellulose as raw material, is an important biological platform molecule. Its preparation and catalytic oxidation of subsequent products have important research significance and practical value. In the actual production process, porous organic polymer (POPs) catalysts are highly suitable for biomass catalytic conversion due to its high efficiency, low cost, good designability, and environmentally friendly features. Here, we briefly described the application of various types of POPs (including COFs、PAFs、HCPs、CMPs) in the preparation and catalytic conversion of HMF from lignocellulosic biomass, and analyzed the influence of the structural properties of catalysts for the catalytic performance. Finally, we summarized some challenges that POPs catalysts will face in biomass catalytic conversion, and prospected the important research directions in future. This review would provide valuable references for the efficient conversion of biomass resources into high-value chemicals in practical applications.

Developing advanced carbon materials by utilizing biomass waste has attracted much attention. Herein, a N-doped carbon material (RSM-0.33-550) was prepared by directly pyrolyzing reed straw and melamine. The as-prepared RSM-0.33-550 possessed a N content of 6.02% and a specific surface area of 547.1 m2 g-1. As the anode for supercapacitors (SCs), in 6 M KOH, such RSM-0.33-550 exhibited a capacitance of 202.8 F g-1 at a current density of 1 A g-1. At a high current density of 20 A g-1, it still remained a capacitance of 158 F g-1. Notably, it delivered an excellent stability with capacity retention of 96.3% at 20 A g-1 after 5000 cycles. This work not only offer a new electrode material for SCs, but also gives a new insight for rationally utilizing the biomass waste for energy storage.

Bifunctional catalysts consisting of mono- or bimetallic nanoparticles (NPs) and zeolite supports received considerable attention due to excellent catalytic properties in numerous reactions including direct and indirect biomass processing. Here, we discuss major approaches to the preparation of NPs in zeolites, concentrating on methods allowing the best interplay (synergy) between metal and acid sites which is normally achieved for small NPs well-distributed through zeolite. We focus on modification of zeolites to provide structural integrity and controlled acidity which can be accomplished by incorporation of certain metal ions or elements. The other modification avenue is the adjustment of the zeolite morphology including creation of numerous defects for the NP entrapment and designed porosity. In this review we also provide examples of synergy between metal and acid sites and emphasize that without density functional theory calculations many assumptions about interactions between active sites stay unvalidated. Finally, we describe the most interesting examples of direct and indirect biomass (waste) processing for the last five years.

The isolation and potential applications of chitosan from the fungal source is an alternative to crustacean chitosan and synthetic polymers. The strains of Basidiomycota (Heterobasidion annosum, Phanerochaete chrysosporium, Pleurotus ostreatus, Trametes versicolor, Lentinus lepideus) with different environmental distribution, ecological importance, and industrial application were studied for mycelial biomass production in submerged (SF) and solid state fermentation (SSF). Further, the chitosan from fungal cells was extracted and characterized by elemental analyses (nitrogen) and FTIR spectroscopy. The fruiting bodies of Pleurotus ostreatus, Agaricus bisporus and Ganoderma ap-planatum were chosen as a reference material of chitosan content in basidiocarps. Stationary SF gave the lowest biomass yield in comparison with shaken SF and SSF. The role of aeration and agitation in biomass production was clearly observed in shaken SF with the highest yield achieved by P. chrysosporium. The highest biomass yield in SSF produced P. ostreatus and T. versi-color. The content of chitosan within fungal species varied depending on the method of cultiva-tion. The highest chitosan yield among the cultivated strains was obtained from mycelium of P. chrysosporium and T. versicolor in SF. The highest chitosan yield in fungal fruiting bodies demon-strated commercially cultivated mushroom A. bisporus. The extracted chitosan is proposed as functional biopolymer additive for ecological materials to substitute the synthetic wet and dry strength agents in packaging materials.

Conventional hydrogen production, as an alternative energy resource, has relied on fossil fuels to produce hydrogen, releasing CO2 into the atmosphere. Hydrogen production via the dry forming of methane (DRM) process is a lucrative solution to utilize greenhouse gases, such as carbon dioxide and methane, by using them as raw materials in the DRM process. However, there are a few DRM processing issues, with one being the need to operate at a high temperature to gain high conversion of hydrogen, which is energy intensive. In this study, bagasse ash, which contains a high percentage of silicon dioxide, was designed and modified for catalytic support. Modification of silicon dioxide from bagasse ash was utilized as a waste material and the performance was explored of bagasse ash-derived catalysts interacting with light irradiation and reducing the amount of energy used in the DRM process. The results showed that the performance of 3%Ni/SiO2 bagasse ash WI was higher than that of 3%Ni/SiO2 commercial SiO2 in terms of the hydrogen product yield, with hydrogen generation initiated in the reaction at 300 °C. Using the same synthesis method, the current results suggested that bagasse ash-derived catalysts had better performance than commercial SiO2-derived catalysts when exposed to an Hg-Xe lamp. This indicated that silicon dioxide from bagasse ash as a catalyst support could help improve the hydrogen yield while lowering the temperature in the DRM reaction, resulting in less energy consumption in hydrogen production.

Through the use of machine learning algorithms like the Support Vector Machine, it has been show that burn extent can be accurately mapped from hyperspatial drone imagery in both grasslands and forests. Despite these successes, hyperspatial imagery must be acquired via drones, requiring large amounts of time and resources to capture areas much smaller than the large catastrophic fires which result in the majority of the lands burned each year by wildland fires. To overcome this difficulty, high spatial resolution satellite imagery from Worldview2 can be substituted for hyperspatial drone imagery, allowing for larger regions of images to be acquired more easily and efficiently. Additionally, Worldview2 trades spatial resolution for spectral resolution and extent, capturing images in 8 multispectral bands as opposed to 3 band imagery in the visible spectra. This research examines the utility of each of the 8 bands observed in Worldview2 imagery using an Iterative Dichotomiser 3 decision tree, then uses these bands to map burn extent and biomass consumption. Several classifications of burn extent and biomass consumption are produced and compared based on the bands used as inputs. The results show that using Worldview2 imagery to map burn extent and biomass consumption results in highly accurate maps, with slight improvements when additional bands are added.

The presence of metal ions, in high concentrations, in the effluents results from industrial metal coating is a well-known fact. Most of time, such metal ions, once they reach the environment, contribute significantly to its degradation. Therefore, it is essential that before such effluents are discharged into the environment, the concentration of metal ions is reduced (as much as possible), to minimize the negative impact on the quality of ecosystems. Among all methods that can be used to reduce the concentration of metal ions, sorption is one of the most viable options, due to its high efficiency and low cost. Moreover, due to the fact that many of the industrial wastes have sorbent properties, this method is in accordance with the principles of circular economy. Based on these considerations, in this study, mustard waste biomass (resulting after oil extraction) was functionalized with an industrial polymeric thiocarbamate (METALSORB), and used as an sorbent to removal Cu(II), Zn(II) and Co(II) ions from aqueous media. The best conditions for the functionalization of mustard waste biomass were found to be: mixing ratio biomass : METASORB = 1g : 1.0 mL and temperature of 30 C. The experimental sorption capacities of functionalized sorbent (MET-MWB) were 0.42 mmol/g for Cu(II), 0.29 mmol/g for Zn(II) and 0.47 mmol/g for Co(II), and were obtained in the following conditions: pH of 5.0, 5.0 g sorbent/L and temperature of 21 C. Modeling of isotherms and kinetic curves, but also the analysis of the results obtained from desorption processes, demonstrates the usefulness of this sorbent in the treatment of effluents contaminated with metal ions. In addition, tests on real wastewater samples highlight the potential of MET-MWB for large-scale applications.

The emergence of cloud computing, big data analytics, and machine learning has catalysed the use of remote sensing technologies to enable more timely land management of sustainability indicators such as ground cover and grassland biomass, given the uncertainty of future climate and drought conditions. Here, we examine the potential of “regenerative agriculture”, as an adaptive grazing management strategy to minimise bare ground exposure while maximising pasture biomass productivity. High-intensity sheep grazing treatments were conducted in small fields (less than 1 hectare) for short durations (typically less than 1 day). Paddocks were subsequently spelled to allow pasture biomass recovery (treatments comprising 3, 6, 9, 12, and 15 months) with each compared with control treatments with lighter stocking rates for longer periods (2,000 DSE). Pastures were composed of wallaby grass (Austrodanthonia species), kangaroo grass (Themeda triandra), Phalaris (Phalaris aquatica, and cocksfoot (Dactylis glomerata) were destructively sampled to estimate total standing dry matter (TSDM), standing green biomass, standing dry biomass and trampled biomass. We then invoked a machine learning model using Sentinel-2 imagery to quantify TSDM, standing green biomass and standing dry biomass. Faced with La Nina conditions, regenerative grazing did not significantly impact pasture productivity, with all treatments showing similar TSDM and green biomass. However, regenerative treatments significantly impacted litter fall and trampled material, with the high intensity grazing treatments causing more dry matter trampling, increasing litter, enhancing decomposition rates and surface organic matter. Pasture digestibility was greatest for treatments with minimal spelling (3 months), whereas both standing senescent and trampled material were significantly greater for the treatment with 15-month spell periods. Estimates of TSDM using machine learning with Sentinel-2 imagery underestimated TSDM in treatment plots but explained spatiotemporal variability associated within and across treatments. The root mean square error between the measured and modelled TSDM was 903 kg DM/ha, which was less than the variability measured in the field. We conclude that regenerative grazing with short recovery periods (3-6 months) are most conducive to increasing pasture production under high rainfall conditions, and we speculate that high intensity grazing is likely to positively impact on soil organic carbon through increased litterfall and trampling. Our study paves the way forward for using machine learning with satellite imagery to quantify pasture biomass at small scales, enabling management of pastures from afar.

Due to pollution and environmental deterioration, man needed to find other alternatives as energy sources, including biomass. (1) Background: The present research was conducted to evaluate the sugarcane cutting residue; this type of biomass has no use and can be burned to obtain energy. (2) Methods: Through the elaboration of pellets and, in turn, reduce the environmental impact of flora and fauna in crops, for the characterization, the raw material was subjected for the first time to physical treatment such as cleaning, drying, grinding, and sieving so that have the optimal characteristics to be used in the pelleting stage. Then a proximal analysis was conducted based on the ASTM -3172-89 Standard and the determination of the calorific value using the ASTM D-240 Standard. Likewise, the pellets were analyzed in their final stage. This method analyzes the parameters of moisture content, volatile material, ashes, and fixed carbon. (3) Results: It was obtained as a result that for the raw material, the % H=3.543, %MV=86.53, %Cz=6.939, %Cf= 2.987 and Pc= 15.702 KJ/Kg; and for the elaboration of the pellets it was carried out using the mixing proportion, 53% SAR with 47% binder, this was determined using the proximal analysis and the determination of the calorific value, from which the results of % H=5,768 were obtained., %MV=82.313, %Cz=6.376, %Cf= 5.543 and Pc= 15.635 KJ/Kg. (4) Conclusions: In other words, sugarcane cutting residues meet the physicochemical properties to be used as raw material in producing solid biofuel.

Pygoscelis penguin populations in the Antarctic Peninsula have dropped dramatically in the last 50 years. The main probable cause is the reduction in Krill (Euphausia superba), the most important feeding item for Pygoscelis penguins during breeding. The scientific community has expressed concerns on the potential that competition with the fishery during periods of low krill availability might be exacerbating the effects of climate change. By bringing together data on breeding success of penguin colonies throughout the Antarctic Peninsula with information of krill availability from acoustic survey and krill fishery monitoring data, we were able to show that fishery has had in the past an effect over breeding success. That is a consequence of a management strategy based on a constant catch level enabling the fishery to maintain the same levels of production even when krill availability is low. The total catch limit may have represented a substantial amount of the available krill biomass in some years, and we detected that when the catch goes over 5% of the available biomass during summer, breeding success of penguins decreased by one third. We discuss the implications of our findings to the revised ecosystem-based management strategy of the krill fishery in Antarctica.

At the time of tillage, properties of the soil change, thereby changing the conditions of crop development and ultimately their productivity and quality. The effect of non-inversion tillage or no till on faba bean development is stills not widely investigated. For this reason, investigations of tillage systems from deep and shallow ploughing, chiselling, disking to no tillage were tested in Vytautas Magnus University, Agriculture Academy, Lithuania. The results showed that different tillage methods had less influence on faba bean development than meteorological conditions during the growing seasons. Soil chiselling generally showed better faba bean canopy development rates than other treatments. Faba bean roots developed somewhat better in not tilled plots. Vegetative conditions had a significant influence on faba bean development indicators. The effects of vegetative conditions during all four years of the experimentation were significantly different from each other. This shows that, due to rapid climate change, the conditions of each vegetative season become unique and require precise attention.

Biochar is an inexpensive and effective carbon sequestration technology produced by slow and fast pyrolysis of biomass feedstock at elevated temperatures in inert conditions producing large quantities of solid residue (i.e., biochar), condensable liquids (bio-oil) and hydrocarbon gases. Biochar have shown excellent adsorption capabilities. Biochar has shown excellent adsorption capabilities for short-chain PFAS and short chain PFAS. This paper suggests optimal pyrolysis reaction conditions to adsorb PFAS to maximum allowable concentrations in wastewater up to Environmental Protection Agency (EPA) is 70 ng/L. The paper highlights the operation conditions and influential reaction conditions to control the microporous structures in Biochar. The paper also aims to summarize the fundamentals of production of Biochar from biomass slow pyrolysis as well as optimal conditions for extraction of PFAS from wastewater streams and destruction of PFAS in biosolids. The scientific contributions for production of Biochar from biomass pyrolysis are highlighted. The paper also highlights the advantages of biochar over activated carbon in terms of low manufacturing costs and higher adsorption rates.

Carotenoids are essential pigments that play a vital role in the photosynthetic process of algae and are important for human health and nutrition. Despite their potential value, algal carotenoids are being neglected by biofuel industries. Recent research is aimed at producing microalgal lipids and carotenoids simultaneously under abiotic stresses. In this study, the effect of different abiotic stress factors such as Nitrogen (N), Potassium (K), Phosphorous (P), Sulphur (S), light intensity, and photoperiod on biomass, lipid, and carotenoids synthesis in Monoraphidium sp. (MP) were explored utilizing a statistical method. In addition, 2, 7-dichlorofluorescein diacetate (DCF-DA) mediated spectrofluorimetry was employed to detect the ele-vation in ROS level. The results revealed that variations in nutrients and light con-ditions are the key factors in the up-regulation of biomolecules lipids and carote-noids in the algae. The carotenoids profiling was done by Ultra Performance Liquid Chromatography Quadrupole Time-of-Flight Mass Spectroscopy (UPLC-Q-ToF-MS). Among consisting carotenoids violaxanthin, astaxanthin, and beta-carotene were enhanced by 1.3 folds, 1.19 folds, 1.08 folds, while lutein was declined by 1.32 folds under stressed condition compared to control. The identified carotenoids are rec-ognized for their importance in the pharmaceutical and nutraceutical industries, highlighting the significant role of MP in these sectors.

In the recent years, biochar has emerged as a remarkable biosourced material for addressing global environmental, agricultural, biomedical, and energy challenges. However, the performances of biochar rest in part on finely tuning its surface chemical properties, intended to obtain specific functionalities. In this review, we tackle surface treatment of biochar with silane and other coupling agents such as diazonium salts, titatantes, ionic/non-ionic surfactants, as well as nitrogen-containing (macro)molecules. We summarize the recent progress achieved mostly in the last five years, and correlate the nature and extent of functionalization to eye catchy end applications of the surface engineered biochar.

Fruits are commonly used, fresh or processed, to prepare different industrial products with superior nutritional and health-promoting properties. Currently, the demand for processed fruit products has motivated the rapid growth of the fruit processing industries, persuading them to produce an enormous amount of by-products with less utilization. Furthermore, people's shifting dietary habits and lack of awareness of nutritional properties result in an avoidable load of fruit by-products. The knowledge of the value of by-products urges exploration with proper documentation, emphasizing the health benefits of some such products. Hence, this review is prepared by carefully analyzing the recent literature on industrial applications of fruit by-products and their nutritional and health-promoting properties. The use of fruit by-products in food industries for various purposes has been reported in the past and has been reviewed and described here. Fruit by-products are a good source of nutrients and bioactive components, including polyphenols, dietary fibers, and vitamins, implying that they could have an important role for novel, value-added functional food properties. Furthermore, fruit by-products are used as the substrate for the production of organic acids, essential oils, enzymes, fuel, biodegradable packaging materials, and preservatives.

United Nations Framework Convention on Climate Change (UNFCCC) has recently established the Reducing Emissions from Deforestation and forest Degradation (REDD+) program that requires countries to report their carbon emissions and sink estimates through national greenhouse gas inventories (NGHGI). Thus, developing automatic systems capable of estimating the carbon absorbed by forests without in-situ observation becomes essential. To support this important need, in this work we introduce ReUse, a simple but effective deep-learning approach to estimate the carbon absorbed by forest areas based on remote sensing. The novelty of the proposed method is in the use of the public above-ground biomass (AGB) data from the European Space Agency's Climate Change Initiative Biomass project as ground truth to estimate the carbon sequestration capacity of any portion of land on Earth using Sentinel-2 images and a pixel-wise Regressive UNet. The approach has been compared to two literature proposals, using a private dataset and human-engineered features. The results show a greater generalization ability of the proposed approach, with a decrease in Mean Absolute Error and Root Mean Squared Error, respectively, of 16.9 and 14.3 in the area of Vietnam and 4.7 and 5.1 in the area of Myanmar over the runner-up. Finally, as a case study, we reported an analysis made for the Astroni area, a nature reserve located near the metropolitan area of Naples in southern Italy, struck by a large fire, producing predictions consistent with values found by experts in the field. These results further support the use of such an approach for the early detection of AGB variations, both in urban and rural areas.

Piggery wastewater (PWW) is characterized by its high concentrations of organic matter and ammonium, and by their odour nuisance. Traditionally, PWW has been treated in open anaerobic lagoons, anaerobic digesters and activated sludge systems, which exhibit high greenhouse gas emissions, a limited nutrients removal and a high energy consumption, respectively. Photosyn-thetic microorganisms can support a sustainable PWW treatment in engineered photobioreactors at low operating costs and with an efficient recovery of carbon, nitrogen and phosphorous. These microorganisms are capable of absorbing solar irradiation through the photosynthesis process to obtain energy, which is used for their growth and associated carbon and nutrients assimilation. Purple phototrophic bacteria (PPB) represent the photosynthetic microorganisms with the most versatile metabolism in nature, while microalgae are the most studied photosynthetic microor-ganisms in recent years. This review describes the fundamentals, symmetry and asymmetry of PWW treatment using photosynthetic microorganisms such as PPB and microalgae. The main photobioreactor configurations along with the potential of PPB and microalgae biomass valori-zation strategies are also discussed.

Nanoparticles (NP), Nanoaerosols (NA), ultrafine particles (UFP), and PM0.1 (particles with a diameter ≤ 0.1 µm or 100 nm) are interchangeably used in the field of atmospheric studies. PM0.1 are emitted from both natural and anthropogenic sources. The main emission sources of PM0.1 are combustion processes, including biomass and fossil fuel. Moreover, secondary formation via atmospheric photochemical reactions can also occur depending on meteorological conditions and the suspended pollutant species. Identifying the physical and chemical characteristics and spatial and temporal variations is vital in terms of understanding the effect of NPs on the environment, the global climate, and human health risks. This review article summarizes recent research on PM0.1 in Thailand. The review involves peer-reviewed papers from Scopus and the Web of Science databases, and includes the most recently published articles in the past ten years (2013-2022). UFPs mainly come from the combustion processes such as motor vehicles. The high mass concentration of PM0.1 that occurs during the dry season in which open fires depend on the specific region of Thailand. Particulate pollution from local and cross-border countries also needs to be considered in terms of the concentrations of ambient nanoparticles. The overall conclusions reached will likely have a beneficial long-term impact on achieving a blue sky over Thailand through the development of coherent policies and managing new air pollution challenges and sharing knowledge with a broader audience.

An upsurge in global population over the years and rapid urbanization have accelerated huge dependence on petroleum-derived fuels and consequent environment concerns owing to green-house gas emissions in the atmosphere. An integrated biorefinery uses lignocellulosic feedstock as raw material for the production of renewable biofuels, and other fine chemicals. The sustain-able bio-economy and the biorefinery industry would benefit greatly from the effective use of lignocellulosic biomass obtained from agricultural feedstocks to replace petrochemical products. Lignin, cellulose, hemicellulose, and other extractives, which are essential components of ligno-cellulosic biomass, must be separated or upgraded into useful forms in order to fully realize the potential of biorefinery. The development of low-cost and green pretreatment technologies with effective biomass deconstruction potential is imperative for an efficient bioprocess. The abun-dance of microorganisms along with their continuous production of various degradative en-zymes makes them suited for the environmentally friendly bioconversion of agro-industrial wastes into viable bioproducts. The present review highlights the concept of biorefinery, ligno-cellulosic biomass and its valorization by green pretreatment strategies into biofuels and other biochemicals. The major barriers and challenges in bioconversion technologies, environmental sustainability of the bioproducts and promising solutions to alleviate those bottlenecks are also summarized.

COPD is a chronic inflammatory disease characterized by progressive airflow obstruction. Tobacco smoking is the main cause of COPD (COPD-TS), but chronic exposure to biomass smoke (COPD-BS), mainly wood smoke, is the second risk factor; both are considered to cause different phenotypes of COPD. COPD-BS is more eosinophilic than COPD-TS. The objective of the present study was to evaluate the serum level of interleukins involved in eosinophil maturation, recruitment, and survival, and their association with small airway obstruction, measuring cytokines by multiplex test (Bio-Plex) and evaluating the central airway resistance with impulse oscillometry (IOS), comparatively in patients with COPD due to biomass and smoking. The results showed that IL-1ra, IL-2, IL-4, IL-8, IL-9, IL-13, IL-17, and eotaxin were increased in COPD-BS related to COPD-TS. Resistance parameters showed that R5, X5, AX (area reactance), and R5-R20 were significantly higher in COPD-BS than in the COPD-TS group (p < 0.05). R20 was not different between the groups. These data suggest that the cytokines involved in the effect of eosinophils on airway inflammation in COPD-BS were increased compared with COPD-TS, which appears to be related to a predominance of peripheral airway obstruction in patients with COPD-BS more than in COPD-TS

NH4Cl is one of the nitrogen sources for microalgal cultivation. However, excessive amounts of NH4Cl affects microalgal physiology and biomass contents. In this study, the effects of ammonium on microalgal growth and TAG content in the green microalga (Chlamydomonas reinhardtii) was investigated. Microalgal growth and TAG content under photoautotrophic conditions were found to be unchanged with 17 mM of ammonium, while this compound interfered with microalgal growth and induced TAG content under mixotrophic conditions with acetate supplementation. This suggested that ammonium could induce TAG production when acetate occurred in microalgal cultivation. Further, the effects of two different concentrations of NH4Cl (17 mM and 60 mM) on the cells under mixotrophic conditions were investigated. The results showed that both concentrations reduced microalgal growth, but induced total lipid and TAG content, especially after a 4-day cultivation. The oxygen evolution and Fv/Fm ratio showed that both concentrations completely inhibited the oxygen evolution on Day 4. The 60 mM NH4Cl reduced the Fv/Fm ratio from 0.7 to 0.48 indicating that ammonium supplementation directly affects the microalgae photosynthesis performance. A total of 1782 proteins were successfully identified using proteomics analysis. Among them, there were nine overexpressed proteins and four proteins were underexpressed. Using the protein–ligand interaction analysis, nitrogen metabolism is involved under NH4Cl conditions. This information can provide biochemical knowledge for microalgae development for sustainable energy usage.

Drip irrigation systems are becoming more and more mature and are present extensively applied to increase crop yield and water use efficiency in Xinjiang, northwest China. To investigate the effects of irrigation quota on maize growth, the grain yield, and the irrigation water use efficiency (IWUE), a field experiment with four irrigation quotas (T1 4200m3·hm-2, T2 4800m3·hm-2, T3 5400m3·hm-2 and T4 6000m3·hm-2.) were conducted from 2013 to 2021 in Xinjiang China. The re-sults showed significant changes in maize growth, yield, and irrigation water use efficiency in response to different irrigation quotas. The plant height, leaf area index, SPAD, biomass, yield and harvest index of maize at different irrigation quotas all showed a “single peak curve”, and its change was closely related to the irrigation level. The growth index, dry matter accumulation, yield and irrigation water use efficiency with T3 were the highest. The dry matter transfer effi-ciency, contribution of dry matter translocation to grain and the harvest index with T3 showed significant increase of 13.86%, 26.06%, 29.93% and 7.62% compared to T1, respectively. In com-parison to T1, T2 and T4, the yield of T3 increased by 32.17%, 13.54% and 11.27% respectively, and the irrigation water use efficiency (IWUE) increased by 2.80%, 0.93% and 23.63% respectively. The significant correlations established between the maize yield and irrigation quotas could be sim-ulated by kuznets-style relation. The maize yield was negative correlated with irrigation quotas, When the irrigation quota (x) was 5376.73m3·hm-2, the maize yield (y) was 15841.00m3·hm-2. These results demonstrate that the optimized irrigation quota (5400m3·hm-2 treatment) can effectively improve the growth, yield and irrigation water use efficiency of drip irrigation maize in North-west China. In the meanwhile, it can provide theoretical reference and data support for the op-timal irrigation amount of drip irrigation maize in Northwest Xinjiang.

Accurately quantifying the above-ground volume (AGV) and thus above-ground biomass (AGB) of forest stands is an important aspect in the conservation of mangrove ecosystem owing to their ecological and economic benefits. However, the number of studies focusing on quantifying mangrove forests’ biomass has been relatively low due to their marshy terrain, making exploratory studies challenging. In recent times, the use of LiDAR technologies in forest inventory studies has become increasingly popular, due to the reliability of LiDAR as a highly accurate means of 3D spatial data acquisition. In this study, we propose an end-to-end methodology for estimating AGV of mangrove forest stands from terrestrial LiDAR data. Many of the recent studies on this topic effectively employ machine learning algorithms such as multi layer perceptron, random forests, etc. for filtering foliage in the point cloud data of single trees. This study further extends that approach by incorporating the impact of class imbalance of forest point cloud data in a weighted random forest classifier. For the task of segmentation of wood/foliage points in a single tree point cloud, this approach yielded an average increase of 2.737% in the balanced accuracy score, 0.007 in the Cohen’s kappa score, 2.745% in the ROC AUC score and 0.857% in the F1 score. For the task of AGV estimation of a single tree, this approach resulted in an average coefficient of determination of 0.93 with respect to the ground truth volumes. For the task of counting pneumatophores in a plot-level point cloud, the proposed breadth-first searching method yielded an average coefficient of determination of 0.9391. Also, the machine learning classifier and geometric features used in this study were invariant to tree species and hence could be generalised for the classification of point clouds of other tree species as well. Finally, a breadth-first graph-search segmentation based approach is also proposed as part of this pipeline to estimate the contribution of pneumatophores to the AGB of mangrove forest stands. Since pneumatophores are a special adaptation of mangrove forests for gaseous exchange in marshy environments, this study aims to incorporate the detection and AGB estimation of pneumatophores in the inventory of mangrove forest stands. Studying the contribution of pneumatophores to the AGB of mangrove forest plots could also aid future mangrove forest inventory studies in modeling the underlying root network and estimating the below-ground biomass of mangrove trees.

The demand for an efficient utilization of abundant biomasses is growing for the production of biogas and valuable bioproducts. Lignocellulose biomass is a cheap and most abundant carbon source for the production of biofuels such as bioethanol, biobutanediol, and other bio-based chemicals. Due to its complex heterogeneity, its hydrolysis gives rise to a mixture of sugars, mainly glucose; a hexose and xylose; a pentose. Glucose is the most abundant carbohydrate monomer. Most microorganisms have evolved the ability to utilize it preferably due to carbon catabolite repression regulatory mechanism at the detriment of the pentoses. Some microbes even lack the ability to utilize them. This has led to the sequential use of these sugars and accompanying reduced productivity due to inadequate utilization of the pentoses. Also, this sequential utilization of the sugars takes time and makes the overall processes economically costly. Since lignocellulose hydrolysates comprise both hexoses and pentoses, the catabolism of these sugar mixtures to biofuels will require an efficient microbial strain capable of simultaneous utilization. The use of CCR negative mutants can achieve this. CCR negative mutants simultaneously utilize pentoses and hexoses, ensuring an improved fermentation efficacy and greater productivity, thus, making the overall bioprocess economically feasible. This article reviewed several approaches employed in creating these mutant microorganisms. A brief insight on carbon catabolite repression and phosphostransferase system were made. It also highlighted the biogas production processes, factors affecting anaerobic digestion, lignocellulosic biomass structure, challenges with their use and solutions to overcoming the challenges.

Seasonal variations in atmospheric ultrafine particulate matter (PM0.1) were monitored in Bangkok, Thailand, from 2016 to 2017. PM0.1 bound organic carbon (OC), and elemental carbon (EC) were collected by a cascade air sampler that can collect PM0.1 and estimated by a thermal-optical carbon analyzer following the IMPROVE-TOR protocol. The annual average PM0.1 in Bangkok was 14.5 ± 4.7 µg/m3, higher than in large Asian cities like Shanghai and Hanoi. Biomass burning from neighboring areas was shown to increase the particle concentration. Apparent risings in carbon species as OC, EC, and OC/EC ratios in the wet and dry seasons were observed, and Char-EC/Soot-EC displayed that the PM0.1 in the Bangkok atmosphere was influenced mainly by the vehicle exhaust, even though the influence of biomass burning was more sensitive during the dry season. The effective carbon ratio (ECR) displays that carbonaceous aerosol is light-absorbing; the dry season increase contributed to climate and air quality. The finding of this work is of great importance to air pollutants control policies in urban areas.

Citron watermelon (Citrullus lanatus var. citroides) is an extremely drought-tolerant cucurbit crop widely grown in sub-Saharan Africa in arid and semi-arid environments characterized by drought. The species is a C3 xerophyte used for multiple purposes, including intercropping with maize and has a deep taproot system. The deep taproot system plays a key role in the species’ adaptation to dry conditions. Understanding root system development of this crop could be useful in identifying traits for breeding water-use efficient and drought-tolerant varieties. This study compared root system architecture of citron watermelon accessions under water-stress conditions. Nine selected and drought-tolerant citron watermelon accessions were grown under non-stress (NS) and water stress (WS) conditions using the root rhizotron procedure in a glasshouse. The following root system architecture (RSA) traits were measured, namely: root system width (RSW), root system depth (RSD), convex hull area (CHA), total root length (TRL), root branch count (RBC), total root volume (TRV), leaf area (LA), leaf number (LN), first seminal root length (FSRL), seminal root angle (SRA), root dry mass (RDM), shoot dry mass (SDM), root–shoot mass ratio (RSM), root mass ratio (RMR), shoot mass ratio (SMR) and root tissue density (RTD). The data collected on RSA traits were subjected to the analysis of variance (ANOVA), correlation and principal component analyses. ANOVA revealed a significant (p &lt; 0.05) accession × water stress interaction effect for studied RSA traits. Under WS, RDM exhibited significant and positive correlations with RSM (r = 0.65), RMR (r = 0.66), RSD (r = 0.66), TRL (r = 0.60), RBC (r = 0.72), FSRL (r = 0.73) and LN (r = 0.70). Principal component analysis revealed high loading scores for the following RSA traits: RSW (0.89), RSD (0.97), TRL (0.99), TRV (0.90), TRL (0.99), RMR (0.96) and RDM (0.76). In conclusion, the study has shown that the identified RSA traits could be useful in crop improvement programmes for citron watermelon genotypes with enhanced drought adaptation for improved yield performance under drought-prone environments.

Chronic obstructive pulmonary disease (COPD) is strongly associated with tobacco smoking and it is the increasing cause of morbidity and mortality worldwide. The prevalence of COPD among never smokers varies widely across regions, areas, and nations. COPD in smokers has been extensively explored worldwide, however, COPD in non-smokers is under-explored and there is limited data available on non-smoking COPD. We determined the role of environmental pollution and biomass fuel exposure in COPD patients who were non-smokers. We evaluated the clinical profile of non-smokers with COPD in a retrospective observational study. 180 non-smoker COPD patients were selected from the year 2016-to 2018. We found that many patients with COPD are non-smokers and the incidence is higher among the rural population, suggesting that non-smoking COPD is evolving rapidly due to biomass smoke and other environmental pollutant exposures.

Forests play an important role in reducing greenhouse gases in the atmosphere, thereby mitigating the impact of climate change. Estimating the accumulated biomass in a forest ecosystem is important for assessing the productivity and sustainability of the forest. Allometric models for above ground biomass (AGB) are linear regression equations based on the relationships between biomass and diameter at breast height (DBH), tree height (H), and/or wood density. This study estimates AGB in the Colo-I-Suva Forest Park by applying the allometry of Chave et al (2005) and the diameter: height ratio derived from Payton & Weaver (2011) for height estimation in a plot of 20

The gasification of sugarcane cutting residues (RAC) is a process that occurs in a gasifier where the transformation of this raw material into a solid-state and a gasifying agent with a moderate calorific value occurs, thanks to the application of heat. And under restricted oxygen levels, we can say that there are several styles of gasifiers for air, steam, oxygen, and hydrogen, all of which have a performance that can be analyzed and categorized by their performance to avoid damage to the environment. (1) The objective of this article is based on the mathematical development using simulation of the gasification of cane cutting residues. (2) In the methodology, the simulation of the gasification and CO₂ capture process was developed from the biomass residues of the sugarcane cutting residues; it was carried out as a transformation of the primary fuel into a gas stream whose main components are CO₂ and H₂, which can be separated relatively easily by their concentrations, available pressures and in some cases, their temperatures; (3) According to the kinetic data obtained, the second-order reaction in the transformation and improvement of the process was identified; applying to the optimization of development in the capture of CO₂, contributing to the reduction of greenhouse gases. (4) The gasification simulation process results in a biomass conversion corresponding to 93% of its feed and the formation of volatiles whose molar fraction corresponds to 37% H₂, 12% CH₄, 37% CO and 12 % CO₂.

The new climate law introduces a policy of sustainable construction, the assumption of which is the reduction of CO2 by the construction industry and the use of environmentally friendly materials, such as agricultural, mineral, and recycled waste, while limiting the consumption of natural resources. The article is a literature review that analyzes selected waste materials from various sectors of the economy that can be used as additives or partial substitutes for natural resources in the production of cement and in and cement building materials, the production of which reduces CO2 emissions, producing materials with high mechanical strength and environmentally friendly.

We present a novel passive satellite remote sensing approach for observing the three-dimensional distribution of aerosols emitted from wildfires. This method, called AEROS5P, retrieves vertical profiles of aerosol extinction from measurements of the TROPOMI satellite sensor onboard the Sentinel 5 Precursor mission. It uses a Tikhonov-Phillips regularization which iteratively fits cloud-free near-infrared and visible selected reflectances to simultaneously adjust the vertical distribution and abundance of aerosols. The information on the altitude of the aerosol layers is provided by TROPOMI measurements of the reflectance spectra at the oxygen A-band near 760 nm. In the present paper, we use this new approach for observing the daily evolution of the three-dimensional distribution of biomass burning aerosols emitted by Australian wildfires on 20-24 December 2019. Aerosol optical depths (AOD) derived by vertical integration of the aerosol extinction profiles retrieved by AEROS5P are compared with MODIS, VIIRS and AERONET coincident observations. They show a good agreement in the horizontal distribution of biomass burning aerosols, with a correlation coefficient of 0.86 and a mean absolute error of 0.2 with respect to VIIRS. A fair agreement is found between coincident transects of vertical profiles of biomass burning aerosols derived from AEROS5P and from the CALIOP spaceborne lidar. The mean altitude of these aerosols derived from these two measurements show a good agreement, with a small mean bias (185 m) and a correlation coefficient of 0.83. Moreover, AEROS5P observations reveal the height of injection of the biomass burning aerosols in 3D. The highest injection heights during the period of analysis are coincident with the largest fire radiative power derived from MODIS. Consistency is also found with respect to the vertical stability of the atmosphere.

The role of agroforestry systems in providing ecosystem services is very crucial. The most significant increase in carbon (C) storage is often achieved by moving from lower biomass land-use systems to tree-based systems like agroforestry (AF). However, estimation of carbon stocks in indigenous agroforestry systems of South-eastern Rift- valley landscapes, Ethiopia the data are scarce. The study was aimed to investigate the biomass, biomass carbon (BC), and soil organic carbon (SOC) stock of Enset based, Enset-Coffee based, and Coffee-Fruit tree-Enset based agroforestry systems. Comparison of SOC stock of agroforestry systems against their adjacent monocropping farms was also investigated. The study was conducted in three selected sites of the Dilla Zuria district of Gedeo zone. Twenty farms (total of 60) representative of each AF system were randomly selected, inventoried and biomass C stocks estimated. Ten adjacent mono-cropping farms which were related to each AF system were selected in a purposive manner for comparison of SOC stock. Inventory and soil sampling were employed in the 10×10 m farm plot. The mean aboveground biomass ranged from 81.1 t ha-1 to 255.9 t ha-1 and for belowground biomass from 26.9 t ha-1 to 72.2 t ha-1. The highest C stock was found in Coffee-Fruit tree-Enset based (233.3±81.0 t ha-1), and the lowest was in Coffee-Enset based agroforestry system (190.1±29.8 t ha-1). The result showed that SOC stocks were not statistically significant between the three AF systems, although they showed a significant difference in their BC stock. The AF systems' C stocks are substantially higher than those reported for tropical forests and other AF systems. The SOC of AF systems was significantly higher than the ones for the adjacent monocropped farms. Therefore, it is possible to deduce that AF systems are storing significant amount of C and contributing to climate change mitigation.

The concentration of total suspended particles (TSP) and nanoparticles (PM0.1) over Hat Yai city, Songkhla province, southern Thailand was measured in 2019. Organic carbon (OC) and elemental carbon (EC) were evaluated by carbon aerosol analyzer (IMPROVE-TOR) method. Thirteen trace elements including Al, Ba, K, Cu, Cr, Fe, Mg, Mn, Na, Ni, Ti, Pb, and Zn were evaluated by ICP-OES. Annual average TSP and PM0.1 mass concentrations were determined to be 58.3 ± 7.8 and 10.4 ± 1.2 µg/m3, respectively. The highest levels of PM occurred in the wet season with the corresponding values for the dry seasons being lower. The annual average OC/EC ratio ranged from 3.8 - 4.2 (TSP) and 2.5 - 2.7 (PM0.1). The char to soot ratios were constantly less than 1.0 for both TSP and PM0.1, indicating that land transportation is the main emission source. A principal component analysis (PCA) revealed that road transportation, industry, and biomass burning are the key sources of these particles. However, PM arising from Indonesian peatland fires causes an increase in the carbon and trace element concentrations in southern Thailand. The findings make useful information for air quality management and strategies for controlling this problem, based on a source apportionment analysis.

Cytochrome P450 (CYPs) is a functionally diversified third-largest gene family that exploded in the plant kingdom. Their role in different organ development has been illustrated by the intervention of phytohormone. Cotton is a model organism for cell differentiation and cell elongation. To decipher the participation of CYPs in different cotton fiber developmental stages, we identified and characterized 2460 CYPs in three diploids and two allotetraploid cottons. Furthermore, In-silico expression and cluster analysis of cotton CYPs was conducted to distinguish the fiber stage-specific clusters that have the determining role in different stages of fiber development. The subgenome expression of two conserved Gossypium hirsutum CYPs, namely, GhCYP78A197 and GhCYP78A198 contributed to fiber initiation at an early stage of fiber development, governed by the co-occurrence of TATA and MYB TFs binding sites. Coexpression network partners of these two GhCYP78A annotated as auxin, kinases, chromatin remodeler, epigenetic regulator and cyclin-related genes that possibly induce the endoreduplication and cell proliferation for fiber cell initiation to define the high yield and biomass.

We live in the world that is completely entangled on energy and thus, Humankind can no longer do without it, power. With electricity being the main form of energy today, this has increased the complexity of our life today. In Uganda, electricity generation is mainly through hydropower which put the country in the bottleneck of over dependence on one source of energy. Yet, there are many energy systems out there that country can diversify its electricity generation. Therefore, the need to understand, the level of development and utilization of various energy systems has been the underlying question for this present study. Comprehensive literature survey was conducted from the electronic databases including ScienceDirect, Wiley, Sage, Scopus, Taylor & Francis, and Google Scholar. The publications in form of reports, conference papers, working papers, discussion papers, journal articles, book sections and textbooks were considered in this study. In total, 11 energy systems including human and animal energy, solid biomass (firewood), hydropower, wind, geothermal, solar, nuclear, peat, coal, petroleum, and non-solid biomass (methanol, hydrogen, ethanol, biodiesel, and biogas) are described. The current and the future development and utilization of these energy systems has been described. The challenges with their development and utilization were elaborated and the solution the challenges were presented. The hydropower with River Nile being the main river for large hydropower plant construction is the dominance energy system in Uganda. Nuclear energy will be the salvation for the country’s electric energy supply in the near future. Therefore, Uganda needs to bet big on nuclear energy.

Forest degradation is known to be widespread in the tropics, but is currently very poorly mapped, in part because there is little quantitative data on which satellite sensor characteristics and analysis methods are best at detecting it. To improve this, we used data from the Tropical Forest Degradation Experiment (FODEX) plots in the southern Peruvian Amazon, where different numbers of trees had been removed from four 1 ha forest plots, carefully inventoried by hand and Terrestrial Laser Scanning before and after the logging to give a range of biomass change (ΔAGB) values. We conducted a comparative study of six multispectral optical satellite sensors (WorldView-3, SkySat, SPOT-7, PlanetScope, Sentinel-2 and Landsat 8) at 0.3 – 30 m spatial resolution, to find the best combination of sensor and remote sensing indicator for change detection. Spectral reflectance, the Normalized Difference Vegetation Index (NDVI) and texture parameters were extracted after radiometric calibration and image preprocessing. The strength of the relationships between the change in these values and field-measured ΔAGB (computed in % ha−1) was analysed. The results demonstrate that: (a) texture measures correlates more with ΔAGB than simple spectral parameters; (b) the strongest correlations are achieved for those sensors with spatial resolutions in the intermediate range (1.5 - 10 m), with finer or coarser resolutions producing worse results, and (c) when texture is computed using a moving square window ranging between 9 - 14 m in length. Maps predicting ΔAGB showed very promising results using a NIR-derived texture parameter for 3 m resolution PlanetScope (R2 = 0.97 and RMSE = 1.80 % ha−1), followed by 1.5 m SPOT-7 (R2 = 0.74 and RMSE = 5.25 % ha−1) and 10 m Sentinel-2 (R2 = 0.71 and RMSE = 5.55 % ha−1). Texture models derived from 0.3 m WorldView-3 improved with increasing window size, with highest R2 of 0.62 and RMSE = 6.35 % ha−1 for a window of 14 m in length. The degradation in our field plots is invisible to the 30 m resolution Landsat data. Our findings imply that, at least for lowland Peru, low-medium intensity disturbance can be detected best in optical wavelengths using a texture measure derived from 3 m PlanetScope data. That such data are being collected daily, and currently released free as monthly mosaics over tropical forests as part of the Norway’s International Climate and Forest Initiative (NICFI), is excellent news for monitoring such degradation.

The building sector of most tropical countries still use predominantly primary biomass as the principal fuel. This has adverse effects like CO2 emission and deforestation and is associated with issues like poverty, ill-health, and low standard of living. Therefore, energy policies try to improve on the efficiency of firewood and charcoal end-use technologies, to palliate the negative effects. In this research, the global change assessment model (GCAM) is used, to investigate the impact of efficiency improvement on the energy consumption pattern of the building sector of developing countries. The aim of the study is to provide empirical data that would better inform policymakers on the effects of modernizing these primary fuels. The study developed three scenarios with different levels of efficiency improvements. The results show that efficiency improvement rather increases primary biomass consumption and CO2 emission. However, there is a fall in the consumption of traditional biomass in the second half of the modelling period. The increase in biomass-based fuels consumption was seen to be linked to their affordability. Therefore, policymakers need not only elaborate policies that improve biomass efficiency, but also introduce and motivate other clean cooking fuels like butane, biogas, and electricity.

The introduction of organic and inorganic substances to the environment is a result of human activities such as agriculture, domestic and industrial wastewater which leads to pollution. Treatment processes of these wastewaters are being conducted globally to eliminate easily settled materials and recover nutrients in an attempt to release clear and apparently clean effluent into natural waters. Lack of removing inorganic nitrogen and phosphorus nutrients is the greatest cause of eutrophication in water bodies which inhibits the life of other organisms as well as pose a threat to human life and loss of the economy. Different technologies have been applied and are being developed to recover nutrients as well as heavy metals from wastewater to meet the permissible limits before discharging effluents. Wastewater treatment using microalgae offers an opportunity to provide tertiary bio-treatment and production of valuable biomass. Microalgae use the available inorganic nitrogen and phosphorus for their growth which are then harvested for various uses. Additionally, they have the ability to remove heavy metals and some toxic compounds. The main specific microalgae species in this study is the Chlorella sorokiniana with the Aequorea victoria jellyfish This paper reviews some of the wastewater treatment processes and focus on the use of microalgae and some of the shortcomings of the technologies and how they can be improved to achieve maximum nutrient recovery economically with low energy demand.

CONTEXT– Energy is widely involved in human activity and corresponding emissions of SOX, NOX and CO2 from energy generation processes affect global climate change. Clean fuels are desired by society because of their reduced greenhouse gas emissions. Hydrogen is once such candidate fuel. Much hydrogen is produced from fossil fuel, with biomass being an alternative process. OBJECTIVE– The project compared the environmental impact of hydrogen production by natural gas steam reforming vs. biomass gasification. METHOD–Environmental impact was calculated from the input and output data from life cycle inventory analysis. The impact assessment was focused on greenhouse gas emission, acidification, and eutrophication. Models of the two processes were developed and analysed in OpenLCA. The agribalyse database was used to connect inventory flow data to environmental impacts. FINDINGS– For all three metrics, biomass gasification had lower impacts than natural gas steam reforming, sometimes by large margins. For biomass gasification the silica sand production contributes most to all three impact categories, whereas for natural gas steam reforming it is the LPG extraction.

Three significant changes have occurred in the winter climate in Europe recently: increased UK flooding; Iberian drought; and warmer temperatures north of the Alps. The literature links all three to a persistent, significant increase in sea level pressure over Southern Europe, the Mediterranean, Iberia and the Eastern Atlantic (SEMIEA) which changes the atmospheric circulation system: forcing cold fronts to the north away from Iberia; and creating a south westerly flow around the northern perimeter of the high-pressure region bringing warmer, moist air from the subtropical Atlantic to the UK and Europe which increases precipitation in the UK and raises the temperature in Europe. I use the Last Millennium Ensemble, MERRA-2 and Terra-NCEP data to demonstrate that the extreme, anthropogenic, West African aerosol Plume (WAP) which only exists from December to April perturbs the northern, regional Hadley Circulation creating the high pressure in the SEMIEA. I also show that the anthropogenic WAP has only existed in its extreme form in recent decades as the two major sources of the WAP aerosols: biomass burning; and gas flaring have both increased significantly since 1950 due to: a four-fold increase in population; and gas flaring rising from zero to 7.4 billion m3/annum and note that this time span coincides with the changes in the three elements of the winter climate of Europe. I also suggest that it may be possible to eliminate the WAP and return the winter climate of Europe to its natural state after the crucial first step of recognising the cause of the changes is taken.

The main purpose of this study was to determine the size and direction of the seasonal dynamics of organic carbon (Сmicro) and nitrogen (Nmicro) biomass of microorganisms and microbial index (Cmicro : Corg) of natural and agrocenoses with their different uses. Field research methods involved taking of soil samples in 0-10-, 10-20- and 20-40 сm layers. Under laboratory conditions, the content of total soil carbon was determined by dry oxygen combustion on a Vario EL III analyzer (Elementar Analyzensysteme, Hanau, Germany). The carbon content of microbial biomass (Сmicro) was determined by chloroform fumigation extraction method (CFE). To freshly taken soil samples (2 hours) and soil samples after their 24-hour fumigation with chloroform vapors, 0.5 M K2SO4 was added to extract biomass lysis products of soil microorganisms. The content of organic carbon and nitrogen in the biomass of microorganisms in the obtained filtrates was determined on the Elementar Liqui TOC II, Analyzensysteme GmbH, Germany. The carbon content of microbial biomass was calculated from the difference between carbon in fumigated and control samples using a factor of 0,45 - for carbon and 0,54 – for nitrogen. The microbial index of soils was determined by the ratio between the carbon of microorganisms and the total organic carbon of the soil – Cmicro : Corg • 100 (%). Average values and confidence intervals were determined for each defined indicator. The Bonferoni method was used to correct the errors of multiple comparative samples of a one-way ANOVA analyze. K. Pearson’s linear correlation analysis was used to establish the relationships between the dynamics of carbon biomass of microorganisms and organic carbon of the soil during the growing season. Our research has shown the dynamics of Сmicro, Nmicro, Сmicro : Nmicro and Cmicro : Corg during the growing season. Analysis of the box plot showed the largest amplitude of Сmicro changes in the upper 0-10 cm layer of izogumusol. The smallest difference in the quartile range (IQR0,25-0,75) was for no-till and overhang (Ab) in the upper 0-10-, no-till (NT) and fallow (F) - in the layer 10-20- and plowing (CT) - in a layer of 20-40 cm. The content of organic carbon biomass of microorganisms in the upper layer of izogumusol at the beginning of the growing season had the highest values of Ab (577,79  1,64 mg/kg), NT (485,43  1,97 mg/kg) and CT (470,43  0,77 mg/kg), the smallest - for F (370,15  2,18 mg/kg). The content of Nmicro during this period decreased from Ab to Comb (combined tillage), NT, CT, Rot (rotary tillage), RT (reduced (ridge) tillage) and F, respectively. In the 20-40 cm layer, the highest values of Сmicro and Nmicro were observed in mid-July. The lowest values of Сmicro and Nmicro and the largest – Сmicro : Nmicro were found in late August for all variants and layers of the study. The dynamics of the microbial index resembled the trends of Сmicro and Nmicro. The largest share of Smicro in Sorghum during the growing season, on average was: - Ab (1,82  1,85 %) and NT (1,66  1,52 %) - in the layer 0-10-, - Ab (1,23  1,27 %) and NT (1,29  1,32 %) - in the layer 10-20- and - Ab (1,19  1,09 %) and F (1,11  1,077 %) - in a layer of 20-40 cm. Different use of izogumusol affected the amplitude of seasonal changes of Сmicro and Nmicro and did not affect on their direction. The maximum content of Сmicro and Nmicro was observed at the beginning of the growing season - in a layer of 0-10 cm and in mid-July - in a layer of 20-40 cm, the minimum - at the end of the summer period. During this period, the widest ratio of Сmicro : Nmicro was for F and CT - in the layer 0-20 cm and CT and Rot - in the layer 20-40 cm. The Pearson’s correlation coefficient between Сmicro and Corg increased from the upper 0-10- to the lower 20-40 cm layer of izogumusol. "Strong" and "high" negative correlations have been established between Сmicro and Corg, but no pattern has been found between the correlation coefficient and tillage technologies.

Ethanol produced from various biobased sources (bioethanol) has been gaining high attention lately due to its potential to cut down net emissions of carbon dioxide while reducing burgeoning world dependence on fossil fuels. Global ethanol production has increased more than six-fold from 18 billion liters at the turn of the century to 110 billion liters in 2019 (1,2). Sugar cane and corn have been used as the major feedstocks for ethanol production. Lignocellulosic biomass has recently been considered as another potential feedstock. This paper reviews recent developments and current status of commercial production of ethanol across the world. The review includes the ethanol production processes used for each type of feedstock, both currently practiced at commercial scale and newly developed technologies, and production trends in various regions and countries in the world.

Current satellite remote sensing methods struggle to detect and map forest degradation, a critical issue as it is likely a major and growing source of carbon emissions and biodiveristy loss. TanDEM-X InSAR phase height (hϕ) is a promising variable for measuring forest disturbances, as it is closely related to mean canopy height, and thus should decrease if canopy trees are removed. However, previous research has focused on relatively flat terrain, despite the fact that much of the worlds’ remaining tropical forests are found in hilly areas, and this inevitably introduces artifacts in sideways imaging systems. In this paper, we find a relationship between hϕ and aboveground biomass change in four selectively logged plots in a hilly region of central Gabon. We show that minimising the level of multilooking in the interferometric processing chain strengthens this relationship, and that degradation estimates across steep slopes in the surrounding region are improved by selecting data from the most appropriate pass directions on a pixel-by-pixel basis. This shows that TanDEM-X InSAR can measure the magnitude of degradation, and that topographic effects can be mitigated if data from multiple SAR viewing geometries are available.

Many corporations and governments aspire to become Net Zero Carbon Dioxide by 2030-2050. Achieving this goal requires understanding where energy is produced and consumed, the magnitude of CO₂ generation, and the Carbon Cycle. Many prior proposed solutions focus on reducing future CO₂ emissions from continued use of fossil fuels. Examination of these technologies exposes their limitations and shows that none offer a complete solution. For example, bioethanol is shown to be both carbon and energy inefficient. Direct Air Capture technologies are needed to reduce CO₂ already in the air. The most natural form of Direct Air Capture involves letting nature do the work of creating biomass via photosynthesis. However, it is necessary to break the Carbon Cycle by permanently sequestering that biomass carbon in “landfills” modified to discourage decomposition to CO₂ and methane. Tree leaves and biomass grown on-purpose, such as high yield switchgrass, are proposed as good biomass sources for this purpose. Left unsequestered, leaves decompose with a short Carbon Cycle time constant releasing CO₂ back to the atmosphere. While in any given year, leaves represent a small fraction of a tree’s above ground biomass, leaves can represent a substantial fraction of the total biomass generated by a tree when integrated over a tree’s lifetime. Understanding the chemistry of the distinct phases landfills undergo is the key to minimizing or eliminating decomposition. First, the compact cross-linked structure of cellulose and keeping water out will make it difficult for initial depolymerization to release sugars. Air ingress should be minimized to minimize Phase I aerobic decomposition. pH manipulation can discourage acid formation during Phase II. Lignocellulose is low in nutrients needed for anaerobic decomposition. Inhibitors can be added if needed. The goal is to move quickly to the dormant phase where decomposition stops. The cost for Carbon Capture and Storage (CCS) for growing and sequestering high yield switchgrass is estimated to be lower than CCS for steam reforming of methane hydrogen plants (SRM) and supercritical or combined cycle coal power plants. Thus, sequestration of biomass is a natural, carbon efficient, and low-cost method of Direct Capture. Biomass sequestration can provide CO₂ removal on giga tonnes per year scale and can be implemented in the needed timeframe (2030-2050).

PM_0.1 (particles diameter ≤ 0.1 µm), nanoparticles (NPs), and ultrafine particles (UFPs), were interchangeably used in the scientific communities. PM_0.1 originated from both natural and human sources. However, investigations of PM_0.1 and its effects on the environment, visibility, and human health risk to understand the levels of air pollution, sources, and impacts in South East Asia (SEA) countries continue to be lacking. The concentration of PM_0.1 in most SEA countries are much worse than those in western countries environment. A further motivation of this reviewed article is to provide a critical synthesis of the current knowledge and study of ambient PM_0.1 in SEA cities. The main influence of characteristics of PM_0.1 appears to be local sources including biomass burning and motor vehicles. Continuous monitoring of PM_0.1 in terms of both mass and number concentration should be further understood. A critical review is of great importance to facilitating air pollution control policies and predicting the behavior of PM_0.1 in SEA.

Peat is the main type of peloid used in Polish cosmetic/healing spa facilities. Depending on treatment and origin, peat waste can be contaminated microbiologically, and as result, it has to be incinerated in medical waste incineration plants without energy recovery (local law). Such a situation leads to peat waste management costs increase. Therefore in this work, we checked the possibility of peat waste upcycling to carbonized solid fuel (CSF) using torrefaction. Torrefaction is a thermal treatment process that removes microbiological contamination and improves the fuel properties of peat waste. In work torrefaction conditions (temperature and time) on CSF quality were tested. Parallelly, peat decomposition kinetics using TGA, and torrefaction kinetics with lifetime prediction using macro-TGA were determined. Furthermore, torrefaction theoretical mass and energy balance were determined. The results of the tested peat were compared with reference material (wood), and as result, obtained data can be used to adjust currently used wood torrefaction technologies for peat torrefaction. The results show that torrefaction can improve the high heating value of peat waste from 19.0 MJ x kg-1 to 21.3 MJ x kg-1, peat main decomposition takes place at 200-550 °C following second reaction order (n=2), with an activation energy of 33.34 kJ x mol-1 and pre-exponential factor of 4.40 x 10-1 s-1. Moreover, DSC analysis revealed that peat torrefaction required slightly more energy than wood torrefaction, and macro TGA showed that peat torrefaction has lower torrefaction constant reaction rates (k) than wood 1.05 x 10-5 - 3.15 x 10-5 vs 1.43 x 10-5 - 7.25 x 10-5 s-1.

This review reports the available technologies for the flexible utilization of biomass towards negative CO₂ emissions and addresses the possibility to couple biogas production plants with the electrical grid converting excess electrical energy into storable chemical molecules. This changed mind-set towards biomass utilization can lead readily to the implementation of negative CO₂ emission along the entire bioenergy supply chain without limiting the potential for Power-to-X applications. First, the technologies for direct conversion of waste and wood into gaseous energy carriers are screened, to highlight the potential for the production of renewable fuels. Second, the processes for the removal of CO₂ from biogenic gas streams are analysed in terms of technological performance, cost and further potential for the CO₂ recovered. These technologies are the key to pre-combustion CO₂ capture and negative emissions. Third, the possibility of coupling biomass conversion and synthetic fuels production is explored, providing an overview on the technical maturity of the various energy storage processes. The flexible use of biomass can be an essential part of the future CO₂-free energy systems, as it can directly provide energy carriers all around the year and also large quantities of climate-neutral carbon for the production of synthetic fuels with renewable energy. In turn, when no additional renewable electricity is available, the CO₂ by-product from biofuel synthesis can be used for the negative emissions. This opens the way to an efficient strategy for the seasonal storage of electrical energy, realizing a carbon-neutral energy system coupled with the development of carbon-negative energy strategy.

The carbon stocks in the forests originated from the atmosphere and are accumulated in the organic matter of trees and soils. Forests play major roles in providing ecosystem services like climate change mitigation through carbon sequestration and nutrient flow dynamics. Therefore, the major objective of this study was to estimate carbon stocks of Biteyu forest by quantifying the aboveground biomass of trees, belowground carbon, soil carbon, and carbon stocks of litter pool. Systematic sampling technique was employed for vegetation and carbon data collection. The total of 10 line transects were laid along elevational gradients. The transects were 500 m apart and sampling plots were 300 m apart from each other. Each transect has comprised of a minimum of 4 plots to a maximum of six totaling 50 plots representing the forest for the investigation. A square sample plot of 900 m2 was used to collect vegetation data with a DBH ≥ 2.5 cm and a height of 2 m and above. To sample herbaceous vegetation in the forest floor, five smaller subplots of 1 m x 1 m = 1 m2 (four at the corner and one at the centre of the main plot) were established. The disturbance level was also determined using the cattle interference and selective cutting of trees. The appropriate allometric models were applied for both aboveground and belowground biomass estimations. The findings showed that cattle interference affects the forest understory from growing and recruitment. The mean of cattle interference was 4.77±2.12 per ha and the mean of wood stump was 26.67±9.37 per ha. The size class analysis showed that the smallest diameter class (2.5-10 cm) in the forests represented 37.05% of the total stem density. The diameter classes between 10 and 30 cm comprised a stem density of 41.08%. It was estimated that the total carbon stock of Biteyu forest was about 166.67 ± 16.4 ha-1. The carbon stock in AGB and BGB was estimated to be 87.13 ± 11.80 t ha-1 and 22.94 ± 2.84 t ha-1, respectively. Moreover, the contribution of soil and litter carbon pools to the total carbon in the forest ecosystem were 56.37 ± 1.73 and 0.26 ± 0.01 t ha-1 , respectively. From the present study it can be concluded that estimated mean carbon stock of the forest is smaller than that of other similar forests in the dry evergreen montane forest, which was attributed to the higher anthropogenic disturbances. Therefore, the interventions, which reduce the climate change effect, would be very important in the maintenance of forest ecosystem functioning.

Pollination is the process by which pollen grains are exchanged in plant flowers to allow for fertilisation and production to take place. However, challenges occur when crops are grown under protected structures where there are minimal activities of natural pollination agents such as wind and animals which are responsible for transferring pollen grains from the anther to the stigma. Therefore, the study objective was to determine the effect on hand pollination on the yield of African horned cucumber grown under greenhouse and shade net environment. A factorial experiment with two factors (hand pollinated and non-hand pollinated/control) was conducted under two different growing environments (greenhouse and shade net). African horned cucumber plants were hand self-pollinated in the morning. Pollen were manually transferred with a hand using the new earbud from the male to the female flowers on the same plant (selfing). Results showed that hand pollinated African horned cucumber plants increased total biomass from 0.93 to 2.23 kg under greenhouse environment. Hand pollinated plants increased harvest index from 0.07 to 0.35 under shade net environment. It can thus, be deduced that hand pollination increases African horned cucumber yield in the greenhouse and shade net environments.

This study investigates the hybridization scenario of a single flash geothermal power plant with a biomass driven sCO2-steam Rankine combined cycle where a solid local biomass source, olive residue, is used as a fuel. The hybrid power plant is modeled using the simulation software EB-SILON®Professional. A topping sCO2 cycle is specifically chosen for its potential for flexible elec-tricity generation. A synergy between the topping sCO2 and bottoming steam Rankine cycles is achieved by a good temperature match between the coupling heat exchanger where the waste heat from the topping cycle is utilized in the bottoming cycle. The high temperature heat addition problem common sCO2 cycles is also eliminated by utilizing the heat in the flue gas in the bottoming cycle. Combined cycle thermal efficiency and biomass to electricity conversion efficiency of 24.9% and 22.4% are achieved, respectively. The corresponding fuel consumption of the hybridized plant is found as 2.2 kg/s.

A multi-methodic analysis was performed on 5 samples of fly ashes coming from different biomasses. The aim of the study was to evaluate their possible re-use and their dangerousness for men and environment. Optical granulometric analyses indicate that the average diameter of the studied fly ashes is around 20 µm, whereas only ~1 vol% has diameter lower that 2.5 µm. The chemical composition, investigated with electron probe microanalysis, indicates that all the samples have a prevalent Ca composition, followed by Si and Al. A large content in K and P was observed in some samples, whereas the content in potentially toxic elements is always below the Italian law thresholds. Polycyclic aromatic hydrocarbons are completely absent in all the samples coming from combustion plants, whereas they are present in the fly ashes from the gasification center. Quantitative mineralogical content, determined by Rietveld analysis of X-ray powder diffraction data, indicates that all the samples have a large amorphous content, likely enriched in Ca, and several K and P minerals, such as sylvite and apatite. The results obtained from the performed chemo-mineralogical study allowed to point out that the biomass fly ashes could be interesting materials (1) as amending in clayey soils, in substitution to lime, to stimulating pozzolanic reaction and improve their geotechnical properties, on the one hand, avoiding to mine raw materials and, on the other hand, re-cycling wastes; (2) as agricultural fertilizes made by a new and ecological source of K and P.

Research Highlights: (1) Reed canary grass (RCG) is analysed in Sweden compared to willow and poplar for 2001-2020 (2) Each crop presents a different land-use and climatic profile (3) Average yield records of reed canary grass are similar to willow and poplar (4) There are divergences between trial-based and commercial yields (5) Existing LUC patterns suggest meadow>RCG and RCG>cereal (6) RCG land area is very sensitive to policy incentives. Background and objectives: RCG is an alternative crop for biomass-to-energy due to high yield and frost tolerance. We assess the cultivation in Sweden by using an extensive compilation of data, with emphasis on the extension of the cultivation, areas planted, climatic profile, land use patterns and yield levels. Material and methods: All RCG plantations are analysed for 2001-2020. A geostatistical analysis is performed to characterize where is cultivated and the land uses associated. Climatic, productivity and yield profiles are compared to willow and poplar plantations, from experiments and from commercial plantations. Results: The results show that the cultivation of reed canary grass expanded after 2005, with a maximum of 800 ha in 2009 to then decrease to the current levels of about 550 ha. It is mainly grown in colder climatic areas, with lower agricultural productivity than willow and poplar. Mean yields from trials are 6 odt ha-1 yr-1; commercial yields are 3.5 odt ha-1 yr-1. RCG replace meadow land and is replaced by cereals, when abandoned. Conclusions: Reed canary grass is an interesting alternative, growing on colder areas but on similar yield levels than other energy crops. The cultivation is more sensitive to policy incentives

Biomass is an attractive energy source that can be used for production of heat, power, and transport fuels, and when produced and used on a sustainable basis, can make a large contribution to reducing greenhouse gas (GHG) emissions. Anaerobic digestion (AD) is a suitable technology for reducing organic matter and generating bioenergy in the form of biogas. This study investigates the factors allowing the optimization of the process of biogas production from the co-digestion of wheat straw (WS) and bovine manure. The statistical analysis of the experiments carried out show that ultrasonic processing plays a fundamental role by sonication density and solids concentration leading to improved characteristics of WS by reducing particle size and increasing concentration of soluble chemical oxygen demand. The higher the sonicating power used, the more the waste particles are disrupted. The optimality obtained under mesophilic conditions for WS pretreated with 4% w/w (weight by weight) H2O2 at temperature 36 °C under 10 minutes of ultrasonication at 25 kHz improves the methane yield by 64%.

Chaparral shrublands are the dominant wildland vegetation type in southern California and the most extensive ecosystem in the state. Disturbance by wildfire and climate change have created a dynamic landscape in which biomass mapping is key in tracking the ability of chaparral shrub-lands to sequester carbon. Despite this importance, most national and regional scale estimates do not account for shrubland biomass. Employing plot data from several sources, we built a random forest model to predict above ground live biomass in southern California using remote sensing data (Landsat NDVI) and a suite of geophysical variables. By substituting the NDVI and precipi-tation predictors for any given year we were able to apply the model to each year from 2000-2019. Using a total of 980 field plots, our model had a k-fold cross validation R2 of 0.51 and a RMSE of 3.9. Validation by vegetation type ranged from R2 = 0.17 (RMSE=9.7) for Sierran mixed conifer to R2 = 0.91 (RMSE = 2.3) for sagebrush. Our estimates showed an improvement in accuracy over a two other biomass estimates that included shrublands, with an R2 = 0.82 (RMSE = 4.7) compared to R2 = 0.068 (RMSE = 6.7) for a global biomass estimate and R2 = 0.29 (RMSE = 5.9) for a regional biomass estimate. Given the importance of accurate biomass estimates for resource managers we calculated the mean year 2010 shrubland biomass for the four national forests which ranged from 3.5 kg/m2 (Los Padres) to 2.3 kg/m2 (Angeles and Cleveland). Finally, we compared our estimates to field-measured biomass from the literature summarized by shrubland vegetation type and age class. Our model provides a transparent and repeatable method to generate biomass measure-ments in any year, thereby providing data to track biomass recovery after management actions or disturbances such as fire.

As a consequence of intense industrialization in the last few decades, the amount of agro-industrial wastes has increasing, where new forms of valorization are crucial. In this work, 5 residual biomasses from Maranhão (Brazil) were investigted as supports for immobilization of lipase from Thermomyces lanuginosus (TLL). The new biocatalysts BM-TLL (babaçu mesocarp) and RH-TLL (rice husk) showed immobilization efficiencies &gt;98% and hydrolytic activities of 5,331 U.g-1 and 4.608 U. g-1 respectively against 142 U. g-1 by Lipozyme® TL IM. High esterification activities were also found, with 141.4 U.g-1 and 396.4 U.g-1 from BM-TLL and RH-TLL against 113.5 U.g-1 by TL IM. Results of porosimetry, SEM and BET demonstrated BM and RH supports are mesoporous materials with large hydrophobic area, allowing a mixture of hydrophobic adsorption and confinement, resulting in hyperactivation of TLL. These biocatalysts were applied in the production of hexyl laurate, where RH-TLL was able to generate 94% conversion in 4 h. Desorption with Triton X-100 and NaCl confirmed that new biocatalysts were more efficient with 5 times less protein than commercial TL IM. All results demonstrated that residual biomass was able to produce robust and stable biocatalysts containing immobilized TLL with better results than commercial preparations.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

Lignocellulosic biomass fractionation is typically performed using methods that are somehow harsh to the environment, such as in the case of the kraft pulping. In recent years, the development of new sustainable and environmentally friendly alternatives has grown significantly. Among the developed systems, bio-based solvents emerge as promising alternatives for biomass processing. Therefore, in the present work, the bio-based and renewable chemicals, levulinic acid (LA) and formic acid (FA), were combined to fractionate lignocellulosic waste (i.e., Maritime pine sawdust) and isolate lignin. Different parameters, such as LA/FA ratio, temperature, and extraction time, were optimized to boost the yield and purity of extracted lignin. The LA/FA ratio was found to be crucial regarding the superior lignin extraction from the waste biomass. Moreover, the increase in temperature and extraction time enhances the amount of extracted residue but compromises the lignin purity and reduces its molecular weight. The electron microscopy images revealed that biomass samples suffer significant structural and morphological changes, which further suggests the suitability of the new developed bio-fractionation process. Same was concluded by the FTIR analysis, in which no remaining lignin was detected in the cellulose-rich fraction. Overall, the novel combination of bio-sourced FA and LA has shown to be a very promising system for lignin extraction of high purity from biomass waste, thus contributing to extend the opportunities of lignin manipulation and valorisation into novel added-value biomaterials.

Utilization of Bidirectional Reflectance Distribution Function (BRDF) model parameters obtained from the multi-angular remote sensing is one of the approaches for the retrieval of vegetation structural information. In this research, the potential of multi-angular vegetation indices, formulated by the combination of multi-spectral reflectance from different view angles, for the retrieval of forest above ground biomass was assessed. This research was implemented in the New England region with the availability of a high quality forest inventory database. The multi-angular vegetation indices were generated by the simulation of the Moderate Resolution Imaging Spectroradiometer (MODIS) BRDF/Albedo Model Parameters Product (MCD43A1 Version 6) based BRDF parameters. The effects of seasonal (spring, summer, autumn, and winter) composites of the multi-angular vegetation indices on above ground biomass, angular relationship of the spectral reflectance with above ground biomass, and the interrelationships between the multi-angular vegetation indices were analyzed. Among the existing multi-angular vegetation indices, only the Nadir BRDF-adjusted NDVI ( and Hot-spot incorporated NDVI ( showed significant relationship (more than 50%) with the above ground biomass. This research proposed two more sensitive vegetation structural indices, Fore-scattering Back-scattering NDVI and Vegetation Structure Index (VSI). The Fore-scattering Back-scattering NDVI showed higher sensitivity (R² = 0.62, RMSE = 52.46) towards the above ground biomass than existing multi-angular vegetation indices. Furthermore, the VSI performed in the most efficient way explaining 64% variation of the above ground biomass, suggesting that the right choice of the spectral channel and observation geometry should be considered for improving the estimates of the above ground biomass. In addition, the right choice of seasonal data (summer) was found to be important for estimating the forest biomass while other seasonal data were either insensitive or pointless. The promising results shown by the VSI suggest that it could be an appropriate candidate for monitoring vegetation structure from the multi-angular satellite remote sensing.

This paper presents ensemble learning of multi-source satellite sensors dataset to obtain better predictive performance of the forest biomass. Spectral, spectral-indices, and spectral-textural features were generated from two optical satellite sensors, Landsat 8 Operational Land Imager (OLI) and Sentinel-2 Multispectral Instrument (MSI). In addition, two radar satellite sensors, Sentinel-1 C-band Synthetic Aperture Radar (CSAR), and Advanced Land Observing Satellite (ALOS-2) Phased Array type L-band Synthetic Aperture Radar (PALSAR-2) were utilized to generate backscattering and backscattering-textural features. The plot-wise above ground biomass data available from five forests in New England region were utilized. Ensemble learning of multi-source satellite sensors dataset was carried out by employing four machine learning regressors namely, Support Vector Machines (SVM), Random Forests (RF), Gradient Boosting (GB), and Multilayer Perceptron (MLP). A five-fold cross-validation method was used to evaluate predictive performance of the multi-source satellite sensors. The integration of multi-source satellite features, comprising of spectral, spectral-indices, backscattering, spectral-textural, and backscattering-textural information, through ensemble learning and cross-validation approach implemented in the research showed promising results (R² = 0.81, RMSE = 46.2 Mg/ha) for the estimation of plots-level forest biomass in New England region.

Hydrolysate prepared from water hyacinth biomass, containing a considerable amount of solubilised carbohydrate and nutrients, was utilised as a medium for the cultivation of two strains of Chlorella sorokiniana. These strains were isolated from an oxidation pond using two different media, i.e., BG-11 and Knop's media maintained at pH-9. Different light intensities, light-dark cycles, and various concentrations of external carbon sources (monosaccharides and inorganic carbon) were used to optimise the microalgal growth. It was observed that in the presence of organic carbon (glucose), biomass productivity increased significantly (~300 mgL-1day-1) as compared to that in the presence of only inorganic carbon (~100 mgL-1day-1). For the accumulation of stress products (lipids and carbohydrates), the microalgal strains were transferred to nutrient-amended media (N-amended and P-amended). The combined effects of glucose, inorganic carbon, and a 12h:12h light-dark cycle proved to be optimum for biomass productivity. For Chlorella sp. isolated from BG-11, maximum carbohydrate content (22%) was found in the P-amended medium, whereas high lipid content (17.3%) was estimated in the N-amended medium. However, for Chlorella sp. isolated from Knop's medium, both the lipid (17%) and carbohydrate accumulation (12.3%) were found maximum in the N- amended medium. Kinetic modelling of the lipid profile revealed that kinetic coefficients obtained for strain isolated from BG-11 media were statistically significant from each other.

2,5-Di(hydroxymethyl)furan (DHMF) is a high-value chemical block than can be synthesized from 5-hydroxymethylfurfural (HMF), a platform chemical that results from the dehydration of biomass-derived carbohydrates. In this work, the HMF biotransformation capability of different Fusarium species was evaluated and F. striatum was selected to produce DHMF. The effects of the inoculum size, glucose concentration and pH of the media over DHMF production were evalu-ated by a 23 factorial design. A substrate feeding approach was found suitable to overcome the toxicity effect of HMF towards the cells when added at high concentrations (>75 mM). The pro-cess was successfully scaled-up at bioreactor scale (1.3 L) with excellent DHMF production yields (95%) and selectivities (98%). DHMF was purified from the reaction media with high recovery and purity by organic solvent extraction with ethyl acetate.

Many corporations aspire to become Net Zero Carbon Dioxide by 2030-2050. This paper examines what it will take. It requires understanding where energy is produced and consumed, the magnitude of CO2 generation, and the Carbon Cycle. Reviews are provided for prior technologies for reducing CO2 emissions from fossil to focus on their limitations and to show that none offer a complete solution. Both biofuels and CO2 sequestration reduce future CO2 emissions from fossil fuels. They will not remove CO2 already in the atmosphere. Planting trees has been proposed as one solution. Trees are a temporary solution. When they die, they decompose and release their carbon as CO2 to the atmosphere. The only way to permanently remove CO2 already in the atmosphere is to break the Carbon Cycle by growing biomass from atmospheric CO2 and sequestering biomass carbon. Permanent sequestration of leaves is proposed as a solution. Leaves have a short Carbon Cycle time constant. They renew and decompose every year. Theoretically, sequestrating a fraction of the world’s tree leaves can get the world to Net Zero without disturbing the underlying forests. This would be CO2 capture in its simplest and most natural form. Permanent sequestration may be achieved by redesigning landfills to discourage decomposition. In traditional landfills, waste undergoes several stages of decomposition, including rapid initial aerobic decomposition to CO2, followed by slow anaerobic decomposition to methane and CO2. The latter can take hundreds to thousands of years. Understanding landfill chemistry provides clues to disrupting decomposition at each phase.

The Italian Stone Pine (Pinus pinea L.) is one of the most employed ornamental trees in towns with Mediterranean climates. For example, in the city of Rome, Pinus is the most common genus, with more than 51,000 trees. This study investigates technical and economic features of maintenance operations of Stone Pines and evaluates the productivity and costs of the observed yards. Pruning and felling are the most frequent management operations of trees in towns and this study analyzes the features of these operations carried out in 14 work sites. The operations were carried out either with aerial platforms (19 trees) or ascending the crown by tree-climbing (6 trees). The operations were sampled with time studies (12 trees for pruning and 13 for felling). Work time was measured from the beginning of operations to the transport of the residual biomass to the collection and loading point, using centesimal stopwatches and video recording. The total residual biomass was weighed or assessed. Total observation time amounted to 63.1 hours. The evaluation of the costs of each work site considered the fixed and the variable costs and the costs for the labor force. A Multiple Linear Regression model (statistics: determination coefficient R2: 0.74, adjusted R2: 0.67, p-value < 0.001) which utilizes four regressors easily evaluable before the work, was adopted to predict the gross time of the operations. This paper can contribute to optimize trees maintenance methods in urban sites and to assess the potential residual wood biomass attainable from urban forestry maintenance in the city of Rome.

Carbon sequestration is associated with plant biomass and soils. The amount of carbon sequestration in the Atewa Range Forest Reserve (ARFR) is affected by varied anthropogenic activities like logging, mining and farming. This study estimate the above and below ground carbon stock and assess human-induced stress impacts on the Highly Stressed Vegetation (HSV), Moderately Stressed Vegetation (MSV), and Non-Stressed Vegetation (NSV) in the ARFR. The above ground biomass of trees was determined using the allometric model of (Henry, et al., 2010) whereas plants root biomass was calculated using Cairns et al. (1997). Soil organic carbon was determined using the Walkley–Black method. We observed that carbon stock was higher in the above-ground than the below-ground component. The MSV, recorded the highest stock of carbon followed by the NSV and the HSV whilst sequestrated carbon stocks was generally high and varied across the three stress levels. Within the forest, the intensity of anthropogenic activities has negatively impacted the amounts of carbon sequestrated at various levels.

We hypothesized that rumen fluid with yeast producing cellulase enzyme can occur and also produces a high biomass compared to S. cerevisiae. Therefore, the aim of this study was to screen and isolate yeast from rumen fluids with an experimental design method. We optimized a fermentation medium containing sugarcane molasses as a carbon source and urea as a nitrogen source to measure the efficiency of biomass production and cellulase activity. Two fistulated-crossbred Holstein Friesian steers, averaging 350 ± 20 kg body weight, were used to screen and isolate ruminal yeast. The two experiments were designed. A 12 × 3 × 3 factorial was used in a completely randomized design to determine biomass and carboxymethyl cellulase activity. Factor A was isolated yeasts and S. cerevisiae. Factor B was sugarcane molasses (M) concentration. Factor C was urea (U) concentration. Potential yeast was selected for identified and analyzed as a 4 × 3 factorial use in a completely randomized design including. Factor A was incubation times. Factor B was isolated yeast strains including code H-KKU20 (as P. kudriavzevii-KKU20), I-KKU20 (C. tropicalis-KKU20), and C-KKU20 (as Galactomyces sp.-KKU20). Isolation was under aerobic conditions, resulting in a total of 11 different colonies. We noted two appearances of colonies including, asymmetric colonies of isolated yeast (indicated as A, B, C, E, and J) and ovoid colonies (coded as D, F, G, H, I, and K). The highest biomass was observed in three yeasts including codes H, I, and C-KKU20 when inoculated in 25% molasses with 1% urea (M25+U1) (p <0.01). The highest CMCase activity was observed in yeast code H-KKU20 when inoculated in all media solutions (p <0.01). Ruminal yeasts strains H-KKU20, I-KKU20, and C-KKU20 were selected for their ability to produce biomass and their CMCase enzyme synthesis. Identification of isolates H-KKU20 and I-KKU20 revealed that those isolates belonged to Pichia kudriavzevii-KKU20 and Candida tropicalis-KKU20, while C-KKU20 was identified as Galactomyces sp.-KKU20. Two strains provided maximum cell growth: P. kudriavzevii-KKU20 (9.78 and 10.02 Log cell/ml) and C. tropicalis-KKU20 (9.53 and 9.6 Log cells/ml) at 60 and 72 h of incubation time, respectively. The highest ethanol production was observed in S. cerevisiae: 76.4, 77.8, 78.5, and 78.6 g/L at 36, 48, 60, and 72 h of incubation time, respectively (p <0.01). The P. kudriavzevii-KKU20 yielded the least reducing sugar about 30.6 and 29.8 g/L at 60 and 72 h of incubation time, respectively. It could be concluded that screening and isolating yeast from rumen fluids resulted in 11 different characteristics of yeasts. The first novel yeasts discovered in the rumen fluid of cattle were Pichia kudriavzevii-KKU20, Candida tropicalis-KKU20, and Galactomyces sp.- KKU20. P. kudriavzevii-KKU20 had higher results than the other yeasts in terms of biomass production, cellulase enzyme activity, and cell number.

Sorghum is a multipurpose crop, but Cr(VI) toxicity influenced the production of the crop and have established highlighted courtesy, due to robust toxicity and a comparatively less known mode of action. Many reports approve the negative impact of Cr(VI) on plants. Yet, it is not clear that, at what concentrations, Cr(VI) inhibits the growth and nutrient quality of Sorghum. In the present research, toxic effects appeared after 1ppm of Cr treatment. The plant growth decreased 15 – 20% and nutritional quality decreased 30 – 40% significantly with increasing concentration of Cr(VI). Toxic components increased 14 – 16% with increasing concentration of Cr(VI) in both the varieties (HJ 541 and SSG 59-3). Chromium was accumulated more in roots followed by shoots with increasing Cr(VI) treatments (0-4 ppm). Chromium at 4ppm level was becoming lethal to Sorghum. Sorghum cultivar SSG 59-3 was more tolerable to Cr toxicity than HJ 541. Chromium accumulated in Sorghum and increased HCN content and at higher doses adversely affects the nutritive values and growth making it toxic for animal consumption. These findings may be useful for scheming a mitigation strategy for chromium toxicity.

In some species of salmon, reproductive maturity triggers the development of massive pathology resulting from reproductive effort, leading to rapid post-reproductive death. Such reproductive death, which occurs in many semelparous organisms (with a single bout of reproduction), can be prevented by blocking reproductive maturation, and this can increase lifespan dramatically. Reproductive death is often viewed as distinct from senescence in iteroparous organisms (with multiple bouts of reproduction) such as humans. Here we review the evidence that reproductive death occurs in C. elegans and discuss what this means for its use as a model organism to study aging. Inhibiting insulin/IGF-1 signaling and germline removal suppresses reproductive death and greatly extends lifespan in C. elegans, but can also extend lifespan to a small extent in iteroparous organisms. We argue that mechanisms of senescence operative in reproductive death exist in a less catastrophic form in iteroparous organisms, particularly those involving costly resource reallocation, and exhibiting endocrine-regulated plasticity. Thus, mechanisms of senescence in semelparous organisms (including plants) and iteroparous ones form an etiological continuum. Therefore understanding mechanisms of reproductive death in C. elegans can teach us about some mechanisms of senescence that are operative in iteroparous organisms.

Lake Malombe fish stocks have been depleted by chronic overfishing. Various management approaches (co-management, command control, and ecosystem-based management to fisheries) have been used to manage the fishery. However, the lack of an accurate predictive model has hampered their success. Therefore, we developed and tested a time series model for Lake Malombe fishery. The seasonal fish biomass and CPUE trends were first observed and both were non-stationary. The second-order differencing was applied to transform the non-stationary data into stationary. Autocorrelation functions (AC), partial autocorrelation function (PAC), and Akaike information criterion (AIC) were estimated, which led to the identification and construction of autoregressive integrated moving average (ARIMA) models, suitable in explaining the time series and forecasting. The results showed that ARIMA (1,2,1) provided a better prediction than its counterparts. The model satisfactorily predicted that by 2032, both fish biomass and CPUE will decrease to 3204.6 tons and 59.672 respectively, signifying the potential threat to Lake Malombe fishery. The model justified the necessity of taking precautionary measures to avoid the total collapse of the fishery.

This paper aims to investigate the airflow that can transport emission sources of PM2.5 from neighboring countries to contribute to air pollution in northern Thailand. We applied the coupled atmospheric and air pollution model which is based on the Weather Research and Forecasting Model (WRF) and a Hybrid Single-Particle Lagrangian Integrated Trajectory Model (HYSPLIT). The model output was compared to the ground-based measurement from the Pollution Control Department (PCD) to examine model performance. As a result of model evaluation, the meteorological variables fairly agreed well compared to observation with Index of Agreement (IOA) in ranges of 0.57 to 0.79 for temperature and 0.32 to 0.54 for wind speed, while the fractional bias of temperature and wind speed were 1.3 to 2.5 °C and 1.2 to 2.1 m/s. Burma was a country that contributed much of hotpot locations by 37% of the entire hotspot locations of Southeast Asia in March. The influence of the Asian Monsoon can bring pollutants from neighboring countries such as Burma and Laos toward northern Thailand in March that likely contribute to high concentrations of PM2.5 in northern Thailand.

Over the last decades, microalgal biomass has gained a significant role in the development of different high-end (nutraceuticals, colorants, food supplements, and pharmaceuticals) and low-end products (biodiesel, bioethanol, and biogas) due to rapid growth and high carbon fixing efficiency. Therefore, microalgae are considered a useful and sustainable resource to attain energy security while reducing our current reliance on fossil fuels. From the technologies available for obtaining biofuels using microalgae biomass, thermochemical processes (pyrolysis, HTL, gasification) have proven to be processed with higher viability, because they use all biomass. However, because of the complexity of the biomass (lipids, carbohydrates , and proteins), the obtained biofuels from direct thermochemical conversion have large amounts of heteroatoms (oxygen, nitrogen , and sulfur). As a solution, catalyst-based processes have emerged as a sustainable solution for the increase in biocrude production. This paper's objective is to present a comprehensive review of recent developments on catalyst mediated conversion of algal biomass. Special attention will be given to operating conditions, strains evaluated, and challenges for the optimal yield of algal-based biofuels through pyrolysis and HTL.

Agricultural intensification is considered essential for meeting growing demand for food and biomass for energy and material purposes. Intensifying grasslands is a so-far under-represented although promising option, given their large land area and relatively low management levels. This study quantifies the bioenergy potential from intensifying temporary grasslands in Europe and the integral greenhouse gas emission effects in 2030. We first conduct a literature review of intensification options for European grasslands and then apply the environmental impact assessment model MITERRA-Europe to implement the key intensification option of using multi-species grass mixtures. The results show that 853 kha (or 8%) of temporary grassland could be made sustainably available for additional biomass production. This can be translated into a bioethanol potential of 23 PJ/yr and an emission mitigation potential of 5.8 Mt CO2-eq/yr (if conventional grass mixture from surplus temporary grassland is used for energy) or 72 PJ/yr and 4.0 Mt CO2-eq/yr (if surplus temporary grassland is used for grassy energy crops). Although the bioenergy potential is limited, the intensification measure’s key advantage is that it results in a better environmental performance of temporary grasslands. This makes it a key option for sustainably producing bioenergy in areas with high shares of temporary grasslands.

Bioenergy with carbon capture and sequestration (BECCS) is one strategy to remove CO2 from the atmosphere. To assess the potential scale and cost of CO2 sequestration from BECCS in the US, this analysis models carbon efficiencies and costs of biomass production, delivery, power generation, and CO2 capture and sequestration in saline formations. The analysis includes two biomass supply scenarios (near-term and long-term), two biomass logistics scenarios (conventional and pelletized), two generation technologies (pulverized combustion and integrated gasification combined cycle), and three cost accounting scenarios (gross cost, net cost after electricity revenues, and net cost after electricity revenues with avoided emissions from conventional power generation). Results show cost Mg-1 CO2 as a function of CO2 sequestered (simulating capture up to 90% of total CO2 sequestration potential) and associated spatial distribution of resources and generation locations for the array of scenario options. Under a near-term scenario using 222 million Mg yr-1 of biomass, up to 196 million Mg CO2 can be sequestered at scenario-average costs ranging from $60 to $158 Mg 1 CO2; under a long-term scenario using 823 million Mg yr-1 of biomass, up to 727 million Mg CO2 yr 1 can be sequestered at scenario-average costs ranging from $32 to $242 Mg-1 CO2. These costs are largely influenced by cost accounting scenario, and the CO2 sequestration potential may be reduced if future competing demand reduces resource availability. Results suggest there are multiple feedstock-logistics-generation pathways toward CO2 drawdown that could be incrementally trialed and monitored for environmental sustainability effects. Interactive visualization of results is available at [final link to be determined].

Wildfires generate large amounts of atmospheric pollutants yearly. The development of an emissions inventory for this activity is a challenge today, mainly to perform modeling of air quality. There are free available databases with historical information about this source. The main goal of this study was to process the results of biomass burning emissions for the year 2014 from the Global Fire Assimilation System (GFAS). The pollutants studied were the black carbon, the organic carbon, fine and coarse particulate matter, respectively. The inputs were pre-formatted to enter to the simulation software of the emission inventory. In this case, the Sparse Matrix Operator Kernel Emissions (SMOKE) was used and the values obtained in various cities were analyzed. As a result, the spatial distribution of the forest fire emissions in the Southern Hemisphere was achieved, with the polar stereographic projection. The highest emissions were located in the African continent, followed by the northern region of Australia. Future air quality modeling at a local level could apply the results and the methodology of this study. The biomass burning emissions could add a better performance of the results and more knowledge on the effect of this source.

Recent climatic changes have resulted in an increased frequency and prolonged periods of drought and strained water resources affecting plant production. We explored the possibility of reducing irrigation in a container nursery and studied the growth response of seedlings of economically important forest trees: broadleaf deciduous angiosperms Fagus sylvatica, Quercus petraea and evergreen conifers Abies alba and Pinus sylvestris. We also studied markers of water stress including modifications of biomass allocation, leaf anatomy, proline accumulation and expression of selected genes. Growth of the broadleaved deciduous species was more sensitive to the reduced water supply than that of conifers. Remarkably, growth of the shade tolerant Abies was not affected. Adjustment of biomass allocations was strongest in P. sylvestris, with a remarkable increase in allocation to roots. In response to water deficit both deciduous species accumulated proline in leaves and produced leaves with shorter palisade cells, reduced vascular tissues and smaller conduit diameters, but not conifers. Relative transcript abundance of a gene encoding a Zn-finger protein in Q. petraea and a gene encoding a pore calcium channel protein 1 in A. alba increased as water deficit increased. These findings suggest that in container nursery, the genetic selection can be initiated by water deficit. Our study shows major differences between functional groups in response to irrigation, with seedlings of evergreen conifers having higher tolerance than the deciduous species. This suggests that major water savings could be achieved by adjusting irrigation regime to functional group or species requirements.

In the last decades droughts, deforestation and wildfires have become recurring phenomena that have affected both human activities and natural ecosystems in Amazonia. The time an ecosystem requires to recover from carbon losses is a crucial metric to evaluate disturbance impacts on forests. However, the factors influencing and controlling the recovery time and its spatiotemporal patterns at the regional scale are still poorly understood. In this study, we combined forest growth model, remote sensing and field plots, to map Amazonia-wide (300-ha resolution) impact and recovery time of aboveground biomass (AGB) after drought, fire and a combination of logging and fire. Our simulated results indicate that AGB decreases by 4%, 19% and 46% in forests disturbed by drought, fire and logging + fire, respectively, with an average AGB recovery time of 27 years for drought, 44 years for burned and 63 years for logged + burned areas and with maximum values reaching 184 years in areas of high fire intensity. Our findings provide two major insights in the spatial and temporal patterns of drought and wildfire in the Amazon: 1) the recovery time of the forests takes longer in the southeastern part of the basin, and, 2) as droughts and wildfires become more frequent – since the intervals between the disturbances is getting shorter than forest regeneration – potentially causing a long-lasting damage in these fragile ecosystems and a permanent degradation.

Reduced nutrient mineralization rates under minimum tillage are usually compensated by mineral fertilizer application. These cannot be applied in organic farming systems, however. We hypothesized that organic minimum tillage based on frequent cover cropping and application of dead mulch will improve soil fertility and can compensate for the potential negative effects of minimum tillage. Two long-term field experiments were set up in 2010 and 2011 comparing plough versus minimum tillage including application of transferred mulch. As second factor, the application of compost versus mineral potassium and phosphorus was compared. In 2019, soils were analyzed for soil pH, organic carbon, macro-, micronutrients, microbial biomass, microbial activity and total nematode abundance. In addition, performance of pea in the same soils was determined under greenhouse conditions. Across both experiments, macronutrients (+52%), micronutrients (+11%), microbial biomass (+51%), microbial activity (+86%), and bacterivorous nematodes (+112%) increased in minimum tillage compared with the plough-based system. In the greenhouse, pea biomass was 45% higher in the soil that had been subjected to minimum tillage compared to the plough. In conclusion, soil fertility can be improved in organic minimum tillage systems by intensive cover cropping and application of dead mulch to levels higher than in a plough-based system.

This study investigated the spatial variability of soil organic carbon (SOC), total nitrogen (TN), soil microbial biomass carbon (SMBC) and soil microbial biomass nitrogen (SMBN) in Hongqipao reservoir dominated by different vegetation types and the possible relationships with other soil properties. Top 0–50cm soil samples were collected in sites dominated by different vegetation types within the reservoir littoral zone. There was high spatial variability for SOC, TN, SMBC and SMBN in the Hongqipao reservoir. In addition, the SOC, TN, SMBC and SMBN contents decreased with increasing soil depth. This could be attributed by the fact that when plants detritus decompose, most of their organic matter is mineralized and a new soil layer which contains a greater amount of organic carbon is formed at the top. According to Pearson's correlation values and redundancy analysis (RDA) results, SOC was significantly and positively correlated with TN likely because the vegetation organic matter and liter could be the main nitrogen sources. Similarly, soil moisture content (MC) was significant positive correlated with SOC and TN. Conversely, BD was significant negative correlated with SOC and TN contents in the 0-50 cm soil profiles. However, no significant correlations were observed between SOC, TN, SMBC and SMBN contents and soil pH values. SMBN was significantly and positive correlated with C:N ratio and BD and negative related with MC. Multiple linear regression model revealed that all measures soil properties in this study could explain higher significant variability of the response variables (SOC, TN, SMBC and SMBN contents). This implies that all the measured soil variables within the different vegetation types in the reservoir played a crucial role in determining the contents of SOC, TN, SMBC and SMBN. This study further suggests that vegetation types play a major role in determining the spatial characteristics of SOC and TN. Any changes in the vegetation types in the reservoir may influence the distribution of SOC and TN. This may affect the global carbon budget and the atmospheric greenhouse gas concentration significantly.

Currently, energy security and environmental degradation are the two biggest challenges before humanity that can be surmounted with the use of green and sustainable biofuels produced from lignocellulosic crops. In the future, to ensure adequate and cost-effective supply of biofuels, it requires a sufficient amount of amenable and quality lignocellulosic feedstocks. Therefore, agricultural yields of lignocellulosic biomass crops should be substantially increased by intense genetic maneuvering of key gene regulatory mechanisms and signaling pathways that control plant biomass yield. Recently, numerous miRNAs families are identified, characterized, and validated across the plant kingdom. Plant microRNAs (miRNAs) are 21 to 24 nucleotides long, non-coding small RNAs, act as regulators of their target genes via inducing modifications in transcription, translation, and epigenome. MiRNAs represent many hallmark characteristics like sequence-specific regulation, tissue, and species-specific expression, evolutionary conservation, and functional diversity. They coordinate well physiological and life cycle processes in plants under adverse environmental conditions. Hence, miRNAs offer accurate, precise, and efficient regulatory switches in the miRNA-targeted genetic networks. It is evident from the study of the miR156 family and its target SQUAMOSA PROMOTER BINDING PROTEIN-LIKE (SPL) genes network that controls highly significant agronomic traits in crop plants. The miR156/SPL module acts as a master circuit that synchronizes many intricate complex biological functions such as growth and development, and metabolic processes by sensing internal and external environmental signals in plants. Therefore, miR156 can prove a potential target for miRNAs based plant biotechnology to harmonize complex biofuel traits and improve biomass yield in lignocellulosic biomass crops.

This study presents a new kinetic scheme for the mass yield prediction of waste lignocellulosic biomasses treated by Hydrothermal Carbonization (HTC). The proposed reactions are based on the decomposition, solubilization, and polymerization of each main fraction of the biomass: cellulose, hemicellulose, and lignin. The ash content was assumed to be inert. The kinetic parameters have been obtained by non-linear adjustment using a data set with 220 experimental runs collected from the literature. The results indicate that the pre-exponential factors range was from 7.33 x10¹ to 1.412x10⁵ min^-1, and activation energies were between 33.75 y 225.3 kJ/mol. A good fit is achieved between the observed and predicted data with an R² of 0.81 and an RMSE of 7.7 %. The proposed scheme was validated with the experimental data obtained by the HTC of sawdust (Pinus radiata) and rapeseed (Brassica napus). The experiments were carried out at temperatures of 190, 220, and 250 ºC and reaction times of 0, 30, 60, 90, and 120 min. The predicted values showed an average error of 2.3 and 3.5 %, respectively. Therefore, the kinetic scheme is a useful tool in the conversion analysis of waste biomass treated by HTC.

In order to realize rapid and nondestructive monitoring of wheat biomass in field, field experiments based on different densities, nitrogen fertilizer and variety treatments were studied. RGB images of wheat in the main growth stage were obtained by UAV, and wheat color and texture feature indices were obtained by image processing, and wheat biomass was obtained by field sampling in the same period. Then the relationship between different color and texture feature indices and wheat biomass was analyzed to select the color and texture feature index suitable for wheat biomass estimation. The results showed that there was a high correlation between image color index and wheat biomass in different stages, and most of them reached a very significant correlation level. However, the correlation between image texture feature index and wheat biomass was poor, only a few indexes reached significant or extremely significant correlation level. Based on the above results, the color indices with the highest correlation to wheat biomass or the combining indices of color and texture feature in different growth stage were used to construct estimation model of wheat biomass. The models were validated using independently measured biomass data, and the correlation between simulated and measured values reached the significant level, RMSE were smaller. This indicated that the estimated results by the models were reliable and accurate. It also showed that the estimation models of wheat biomass combined with color and texture feature indices of UAV image were better than the single color index models. The results would provide a new method for real-time monitoring of wheat field growth and biomass estimation.

In this research, the feasibility of using bottom ashes generated by the combustion of biomass (olive pruning and pine pruning) as a source of aluminosilicates (OPBA) has been studied, replacing the metakaolin precursor (MK) in different proportions (0, 25, 50, 75 and 100 wt. % substitution) for the synthesis of geopolymers. As alkaline activator an 8 M NaOH solution and a Na2SiO3 have been used. The geopolymers were cured 24 hours in a climatic chamber at 60 ° C in a water-saturated atmosphere, subsequently demoulded and cured at room temperature for 28 days. The results indicated that the incorporation of OPBA waste, which have 19.7 wt. % of Ca, modifies the characteristics of the products formed after alkaline activation. In general terms, the incorporation of increasing amounts of calcium-rich ashes results in geopolymers with higher bulk density. The compressive strength increases with the addition of up to 50 wt. % of OPBA with respect to the control geopolymers, contributing the composition of the residue to the acquisition of a better behaviour mechanical. The results indicate the potential use of these OPBA waste as raw material to produce unconventional cements with 28-day curing strengths greater than 10 MPa, and thermal conductivities less than 0.35 W/mK.

Alkali-containing submicron particles were measured continuously during three months, including late winter and spring seasons in Gothenburg, Sweden. The overall aims were to characterize the ambient concentrations of combustion-related aerosol particles and to address the importance of local emissions and long-range transport for the atmospheric concentrations in the urban background environment. K and Na concentrations in the PM1 size range were measured by an alkali aerosol mass spectrometer (Alkali-AMS) and a cluster analysis was conducted. Local meteorological conditions and some other data sets were obtained, and back trajectory analyses and chemical transport model (CTM) simulations were included for the evaluation. The Alkali-AMS cluster analysis indicated three major clusters: 1) biomass burning origin, 2) mixture of other combustion sources, and 3) marine origin. Low temperatures and low wind speed conditions correlated with high concentrations of K-containing particles, mainly due to regional emissions from residential biomass combustion; transport of air masses from continental Europe also contribute to cluster 1. The CTM results indicate that open biomass burning in the eastern parts of Europe may have contributed substantially to high PM2.5 concentrations (and to cluster 1) during an episode in late March. According to the CTM results the mixed cluster (2) is likely to include particles emitted from different source types and no single geographical source region seems to dominate for this cluster. The back trajectory analysis and meteorological conditions indicated that the marine origin cluster was correlated with westerly winds and high wind speed; this cluster had high concentrations of Na-containing particles, as expected for sea salt particles.

The purpose of this work is to define optimal growth conditions for batch culture of the cyanobacterium Arthrospira maxima and the microalgae Chlorella vulgaris, Isochrysis galbana and Nannochloropsis gaditana. Thus, we study the effect of three variables on algae growth: i.e., inoculum:culture medium ratio, light:darkness photoperiod and type of culture medium, including both synthetic media and wastewaters. The results showed that the initial inoculum volume did not affect the amount of biomass at the end of the growth (14 days), whereas an excess (18 h) or defect (6 h) in the number of hours of light is determinant for its development. The contribution of nutrients from different culture media modified the growth of the different species. A. maxima was favoured in seawater enriched with Guillard's F/2 as well as C. vulgaris and N. gaditana but in fresh water medium. I. galbana had the greatest growth in the marine environment enriched with Walne’s media. Nitrate was the limiting growth reagent at the end of the exponential phase of growth for C. vulgaris and N. gaditana, while iron was for A. maxima and I. galbana. All species demonstrated their capability to grow in effluents from a wastewater treatment plant and they efficiently consume nitrogen, especially the three microalgae species.

The combination of eco-respectful epoxy compounds with the humins, a by-product of biomass chemical conversion technologies, allow the obtention of materials with high added value. In this work, we propose the chemical connection study of humins with two aliphatic diepoxides through the copolymerization reactions to synthesize sustainable bio-based thermosets. The mechanism insights for the crosslinking between the epoxides and humins was proposed considering the different functionalities of the humins structure. FT-IR spectroscopy, 1 D and 2 D NMR spectroscopy techniques were used to build the proposed mechanism. By these techniques, the principal chain connections and the reactivity of all the components were highlighted in the synthesized networks.

The aim of the study was to determine the presence Fusarium species and mycotoxins in winter wheat grain in Poland. Grain samples from different locations in Poland in 2009 and 2010 were analysed for the content of biomass of Fusarium species and mycotoxins. In 2009 biomass of F. graminearum and F. poae was present in all samples, F. culmorum in 82% of samples, F. avenaceum in 55% of samples. F. sporotrichioides, F. tricinctum and F. equiseti were found only in individual samples. F. langsethiae was not detected. In 2010, five Fusarium species were detected with the exception of F. sporotrichioides. The highest content of biomass was found for F. graminearum followed by F. avenaceum, F. poae and F. langsethiae. The amount of F. culmorum biomass was very low. The most frequently occurring species was F. poae and F. graminearum. In 2009, deoxynivalenol was detected in all samples. In 2010, the average content of deoxynivalenol was lower than in 2009. Nivalenol was detected at very low concentration in both years. Significant correlations between content of F. graminearum biomass and deoxynivalenol concentration in grain and between content of F. poae biomass and nivalenol concentration in grain in 2009 were found. The most important finding of this study was that main Fusarium species infecting wheat kernels in Poland in both years was F. graminearum. The amount of biomass of F. graminearum was the highest in both years. It was present in the most samples. The other frequently detected species was F. poae, which in 2010 appeared in more samples than F. graminearum. However, the amount of F. poae biomass was lower. F. culmorum, species that was previously dominating as wheat pathogen in Poland, was found less frequently than F. graminearum. The amount of biomass of this species was the lowest in 2010.

The following study reports on the first thraustochytrid isolates identified from Iceland. They were collected from three different locations off the northern coast of the country (Location A, Skagaströnd; Location B, Hveravík; and Location C, Eyjafjörður). Using 18S rDNA sequence analysis, isolates from Locations A and B were identified within the Thraustochytrium kinnei species while other isolates within the Sicyoidochytrium minutum species when compared to other known strains. Cells isolated from Locations A (2.10 ± 0.70 g/L) and B (1.54 ± 0.17 g/L) produced more biomass than the ones isolated from Location C (0.43 ± 0.02 g/L). This study offers the first-time examination of the utility of byproducts from fisheries as a nitrogen source in media formulation for thraustochytrids. Experiments showed that isolates produced more biomass (per unit of substrate) when cultured on nitrogen of marine (2.55 ± 0.74 g/L) as compared to of commercial origin (1.06 ± 0.57 g/L). Glycerol (2.43 ± 0.56 g/L) was a better carbon source than glucose (1.84 ± 0.57 g/L) in growth studies. Fatty acid (FA) profiles showed that the isolates from Location C (S. minutum) had low ratios of monounsaturated (4.21 ± 2.96%) and omega-6 (0.68 ± 0.59%) FAs. However, the isolates also had high ratios of docosahexaenoic acid (DHA; 35.65 ± 1.73%) and total omega-3 FAs (40.39 ± 2.39%), indicating that they could serve as a source of marine oils for human consumption and in aquaculture feeds. The T. kinnei isolates from Location A could be used in biodiesel production due to their high ratios of monounsaturated (18.38 ± 6.27%) long chain (57.43 ± 8.27%) FAs.

In the upgrading of biomass pyrolysis vapors to hydrocarbons, dehydration accomplishes a primary objective of removing oxygen and acidic zeolites represent promising catalysts for dehydration reaction. Here, we utilize density functional theory calculations to estimate adsorption energetics and intrinsic kinetics of alcohol dehydration over H-ZSM-5, H-BEA, and H-AEL zeolites. ONIOM calculations of adsorption energies were observed to be inconsistent when benchmarked against QM/Hartree-Fock and periodic boundary condition calculations. However, reaction coordinate calculations of adsorbed species and transition states were consistent across all levels considered. Comparison of ethanol, iso-propanol (IPA), and tert-amyl alcohol (TAA) over these three zeolites allowed for a detailed examination of how confinement impacts reaction mechanisms and kinetics. TAA, seen to proceed via a carbocationic mechanism, was found to have the lowest activation barrier, followed by IPA and then ethanol, both of which dehydrate via a concerted mechanism. Barriers in H-BEA were consistently found to be lower than in H-ZSM-5 and H-AEL, attributed to late transition states and either elevated strain or inaccurately estimating long-range electrostatic interactions in H-AEL, respectively. Molecular dynamics simulations revealed that the diffusivity of these three alcohols in H-ZSM-5 are significantly overestimated by Knudsen diffusion, which will complicate experimental efforts to develop a kinetic model for catalytic fast pyrolysis.

Nitrate is rich in Mars sediments owing to long-term atmospheric photolysis, oxidation, and deposition coupled with a lack of leaching via rainfall. The Atacama Desert in Chile, which is similarly dry and rich in nitrate deposits, is used as a Mars analog in this study to explore the potential effects of high nitrate levels on microbial growth. Seven study sites sampled across an aridity gradient in the Atacama Desert were categorized into 3 clusters – hyperarid, intermediate, and arid sites, as defined by major elements in the regolith, associated biomass, and precipitation. Intriguingly, the distribution of nitrate concentrations in the shallow subsurface suggests that the buildup of nitrate is not solely controlled by precipitation. Correlations of nitrate with SiO2/Al2O3 and grain sizes suggest that sedimentation rates are also important in controlling nitrate distribution. At arid sites receiving more than 10 mm/yr precipitation, rainfall shows a stronger impact on biomass than nitrate does. However, high nitrate to organic carbon ratios are generally beneficial to N assimilation as evidenced both by soil geochemistry and enriched culturing experiments. This study suggests that even in the absence of precipitation on contemporary Mars, the nitrate levels are sufficiently high to benefit potentially extant Martian microorganisms.

Poland is the 3^rdproducer of mushrooms in the world. Mushroom production in Poland accounts for nearly 25% of the total production in the EU, and it is still growing. One type of waste generated during mushroom production is mushroom spent compost (MSC), with a 5:1 (MSC: mushrooms) production rate. We investigated valorizing the MSC to produce fuel via torrefaction (‘roasting’, a.k.a. low-temperature pyrolysis). Specifically, we developed models for the MSC torrefaction kinetics using thermogravimetric analyses (TGA) and the effects of torrefaction temperature (200~300 °C) and process duration time (20~60 min) on the resulting biochar (fuel) properties. The estimated activation energy value of MSC torrefaction was 22.3 kJ^.mol^-1. The highest higher heating value(HHV) = 17.9 MJ^.kg^-1d.m. was found for 280 °C (60 min torrefaction time). The temperature of torrefaction significantly (p<0.05) increased the HHVfor constant process duration. The torrefaction duration time significantly (p<0.05) increased the HHVfor 220 °C and decreased HHVfor 300 °C. The highest mass yield 98.5% was found for 220 °C (60 min), while the highest energy yield was found for 280 °C (60 min). In addition, estimations of the value (€132.3·Mg^-1d.m. or 27.7 €·Mg^-1w.m) and quantity of resulting biochar (from torrefied MSC with 65.3% moisture content) were made based on the 280°C (60 min) torrefaction variant, assuming the price of commercially available coal fuel. We have shown a concept for an alternative utilization of abundant biowaste (MSC). The initial economic evaluation showed that MSC torrefaction might be profitable. This research provides a basis for alternative use of an abundant biowaste and can help charting improved, sustainable mushroom production.

Mushroom production in Poland is an important and dynamically developing element of diverse agriculture. Mushroom spent compost (MSC) is major waste generated during production, i.e., MSC: mushrooms is ~5:1. To date, the main use of MSC is soil application as organic fertilizer. To date, several methods of MSC treatment have been researched and developed including production of compost, bioethanol, biogas, enzyme lactase, xylo-saccharides, and hydrogen. Torrefaction may be considered a novel approach for biomass valorization. Thus, we are pioneering the potential use of MSC valorization via torrefaction. We explored valorizing the waste biomass of MSC via thermal treatment – torrefaction (‘roasting’) to produce biochar with improved fuel properties. Here for the first time, we examined and summarized the MSC torrefaction thermogravimetric analyses, fuel properties data of raw biomass of MSC and biochars generated from MSC via torrefaction. The effects of torrefaction temperature (200~300 °C), process time (20~60 min), on fuel properties of the resulting biochars were summarized. The dataset contains results of thermogravimetric analysis (TGA) as well as proximate analyses of MSC and generated biochars. The presented data are useful in determining MSC torrefaction reaction kinetics, activation energy and to further techno-economical modeling of the feasibility of MSC valorization via torrefaction. MSC torrefaction could be exploited as part of valorization resulting from a synergy between an intensive mushroom production with the efficient production of high-quality renewable fuel.

Root research on field grown crops is hindered by the difficulty of estimating root biomass in soil. Root washing, the current standard method is laborious and expensive. Biochemical methods to quantify root biomass in soil, targeting species-specific DNA, have potential as a more efficient assay. We combined an efficient DNA extraction method, designed specifically to extract DNA from soil, with well-established quantitative PCR methods to estimate the root biomass of twenty-two wheat varieties grown in field trials over two seasons. We also developed an assay for estimating root biomass for black-grass, a common weed of wheat cultivation. Two robust qPCR assays were developed to estimate the quantity of plant root DNA in soil samples, one specific to wheat and barley, and a second specific to black-grass. The DNA qPCR method was comparable, with high correlations, with the results of root washing from soil cores taken from winter wheat field trials. The DNA qPCR assay showed both variety and depth as significant factors in the distribution of root biomass in replicated field trials. The results suggest that these DNA qPCR assays are a useful, high throughput tool for investigating the genetic basis of wheat root biomass distribution in field grown crops, and the impact of black-grass root systems on crop production.

Biowaste generated in the process of Oxytree cultivation and logging represents a potential source of energy. Torrefaction (a.k.a. low-temperature pyrolysis) is one of the methods proposed for the valorization of woody biomass. Still, energy is required for the torrefaction process during which the raw biomass becomes biochar with fuel properties similar to lignite coal. In this work, models describing the influence of torrefaction temperature and residence time on the resulting fuel properties (mass and energy yields, energy densification ratio, organic matter and ash content, combustible parts, lower and higher heating values, CHONS content, H:C and O:C ratios) were proposed according to the Akaike criterion. The degree of the models’ parameters matching the raw data expressed as the determination coefficient (R²) ranged from 0.52 to 0.92. Each model parameter was statistically significant (p<0.05). Estimations of the value and quantity of the produced biochar from 1 Mg of biomass residues were made based on two models and a set of simple assumptions. The value of torrefied biochar (€123.4·Mg^-1) was estimated based on the price of commercially available coal fuel and its lower heating value (LHV) for biomass moisture content of 50%, torrefaction for 20 min at 200 °C. This research could be useful to inform techno-economic analyses and decision-making process pertaining to the valorization of pruned biomass residues.