Heating systems such as heat pump and combined heat and power cycle systems (CHP) are representing a key component in the future smart grid. Their capability to couple the electricity and heat sector promises a massive potential to the energy transition. Hence, these systems are continuously studied numerical and experimental to quantify their potential and develop optimal control methods. Although numerical simulations provide time and cost-effective solution for system development and optimization, they are exposed to several uncertainties. Hardware in the loop (HiL) system enables system validation and evaluation under different real-life dynamic constraints and boundary conditions. In this paper, a HiL system of heat pump testbed is presented. This system is used to present two case studies. In the first case, the conventional heat pump testbed operation method is compared to the HiL operation method. Energetic and dynamic analyses are performed to quantify the added value of the HiL and its necessity for dynamics analysis. The second case, the HiL testbed is used to validate the heat pump operation in a single family house participating in a local energy market. It enables not only the dynamics of the heat pump and the space heating circuit to be validated but also the building room temperature. The energetic analysis indicated a deviation of 2% and 5% for heat generation and electricity consumption of the heat pump, respectively. The model dynamics emphasized the model capability to present the dynamics of a real system with a temporal distortion of 3%.

In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen, depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation, and the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased, while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

We herein described an investigation of a theory, which describes the energies of neutrinos and the source of neutrino oscillations. A series of experiments were conducted to show evidences of the existence a neutrino mass. We also applied theories to explain the reason for the extremely small energy of a neutrino, mainly by employing a vacuum-derived superconducting energy gap from the Bardeen–Cooper–Schrieffer ground state. Moreover, we succeeded in obtaining the transition probabilities of neutrinos’ flavors (i.e., in terms of neutrino oscillation). We focused on the fact that up- and down-quantized space pairs combine by the Lorentz forces, undertake Bose-Einstein condensation, and then create a superconducting energy gap at the energy level of the vacuum with quantum mechanics fluctuation. Eventually, the superconducting energy gap vanishes to form a real body of the neutrino. Furthermore, assuming that the speed of the neutrino is near the speed of light and exhibits Planck’s blackbody emissions, we derived many-body interactions of neutrinos and applied them in Fermi’s golden rule. As a result, the neutrino energy we calculated agreed well within the realms of the experimental results. The calculated transition probabilities of neutrino’s flavor also explain the experiment results very well.

The widely adopted temperature for solid solution heat treatment (ST) for the conventionally fabricated Inconel 718 is 1100 °C for a hold time of 1 h or less. This ST scheme is however not enough to dissolve Laves and annihilate dislocations completely in samples fabricated with Laser metal powder bed fusion (L-PBF) additive manufacturing (AM)-Inconel 718. In spite this, the highest hardness obtained after aging for ST temperatures (970 - 1250 °C) is at 1100 °C/1h [1]. The unreleased residual stresses in the retained lattice defects are potentially affecting other properties of the material. Hence, this work aims to investigate if a longer hold time of ST at 1100 °C will lead to complete recrystallization while maintaining the strength after aging or not. For this study, L-PBF-Inconel 718 samples were ST at 1100 °C at various hold times (1, 3, 6, 9, 16 or 24 h) and aged to study the effects on microstructure and hardness. In addition, a sample was directly aged to study the effects of bypassing ST. The samples (ST and aged) gain hardness by 43 – 49 %, depending on hold time. A high density of annealing twins evolved during 3 h of ST and the quantity only slightly varies for longer ST.

This paper predict and effectively control the temperature distribution of the steady-state and transient states of anisotropic four-layer composite materials online, knowing the density, specific heat, heat conductivity and thickness of the composite materials. Based on the transfer function, a mathematical model was established to study the dynamic characteristics of heat transfer of the composite materials. First of all, the Fourier heat transfer law was used to establish a one-dimensional Fourier heat conduction differential equation for each composite layer, and the Laplace transformation was carried out to obtain the system function. Then the approximate second-order transfer function of the system was obtained by Taylor expansion, and the Laplace inverse transformation was carried out to obtain the transfer function of the whole system in the time domain. Finally, the accuracy of the simplified analytical solutions of the first, second and third order approximate transfer functions was compared with computer simulation. The results showed that the second order approximate transfer functions can describe the dynamic process of heat transfer better than others. The research on the dynamic characteristics of heat transfer in the composite layer and the dynamic model of heat transfer in composite layer proposed in this paper have a reference value for practical engineering application. It can effectively predict the temperature distribution of composite layer material and reduce the cost of experimental measurement of heat transfer performance of materials.

Surface urban heat island (SUHI) depicts the deteriorating thermal environment in high-density cities and local climate zone (LCZ) classification provides a universal protocol for SUHI identification. In this study, taking the central urbanized area of Guangzhou in the humid subtropical region of China as the study area, the maps or images of LCZ, land surface temperature (LST), SUHI and urban design factors were achieved by using Landsat satellite data, GIS database and a series of retrieval and classification algorithms, and the urban design factors influencing SUHI were investigated based on 625 samples of LCZs. The results show that in the summer daytime under the clear sky condition, the LST varied greatly from 26 °C to 40 °C and the SUHI changed in a wide range of -6 °C to 8 °C in the LCZs of the study area. Seven and five urban design factors influencing the summer daytime SUHI were identified for the two dominant LCZ of LCZs 1-5 (LCZ 1 to LCZ 5) and the mixed LCZ (containing at least three types of LCZs), respectively. The summer daytime SUHI prediction models were obtained by using the step-wise multiple linear regression, with the performance of R2 of 0.697, RMSE of 1.21 °C, and the d value of 0.81 for the model of LCZs 1-5, and the values of 0.666, 1.66 °C, and 0.76 for the model of the mixed LCZ, indicating that the models can predict the changes of SUHI with LCZs to a large and satisfactory extent. This study presents a methodology to efficiently achieve a large sample of SUHI and urban design factors of LCZs in the largely urbanized cities, and provides information beneficial to the urban designs and regenerations in the humid subtropical region.

A temperate deep lake, Lake Kuttara, Hokkaido, Japan (148 m deep at maximum) was completely frozen every winter in the 20th century. However, unfrozen conditions of the lake over winter occurred four times in the 21st century, which is probably due to global warming. In order to understand how thermal regime of the lake responds to climate change, its heat storage change was calculated by estimating heat budget of the lake and monitoring water temperature at the deepest point for September 2012–June 2016. As a result, temporal change of the heat storage from the heat budget was very consistent with that from the direct temperature measurement (determination coefficient R² = 0.827). The 1978–2017 data at a meteorological station near Kuttara indicated that there are significant (less than 5% level) long-term trends for air temperature (0.024 °C/yr) and wind speed (−0.010 m/s/yr). A sensitivity analysis for the heat storage from the heat budget estimate and an estimate of return periods for mean air temperature in mid-winter allow us to conclude that the lake could be unfrozen once per about two year in a decade.

Controversial hypotheses to explain consciousness exist in many fields of science, psychology and philosophy. Recent experimental findings in quantum cognition and magnetic resonance imaging have added new controversies to the field, suggesting that the mind may be based on quantum computing. Quantum computers process information in quantum bits (qubits) using quantum gates. At a first glance, it seems unrealistic or impossible that the brain can meet the challenges to provide either of these. Nevertheless, we show here why the brain has the incredible ability to perform quantum computing and how that may be realized.

Photosynthesis is a pivotal process that determines the synthesis of carbohydrates required for sustaining growth under normal or stress situation. Stress exposure reduces the photosynthetic potential owing to the excess synthesis of reactive oxygen species that disturb the proper functioning of photosynthetic apparatus. This decreased photosynthesis is associated with disturbances in carbohydrate metabolism resulting in reduced growth under stress. We evaluated the importance of melatonin in reducing heat stress-induced severity in wheat plants (Triticum aestivum L.). The plants were subjected to 25 ˚C (optimum temperature) or 40 ˚C (heat stress) for 15 days at 6 hours time duration and then developed the plants for 30 days. Heat stress led to oxidative stress with increased production of TBARS and H2O2 content and reduced accrual of total soluble sugars, starch and carbohydrate metabolism enzymes which are reflected in reduced photosynthesis. Application of melatonin not only reduced oxidative stress through lowering TBARS and H2O2 content, through augmenting the activity of antioxidative enzymes but also increased the photosynthesis in plant and carbohydrate metabolism that is needed to provide energy and carbon skeleton to the developing plant under stress. However, the increase in these parameters with melatonin was mediated via hydrogen sulfide (H2S), as the inhibition of H2S by hypotaurine (HT; H2S inhibitor) reversed the ameliorative effect of melatonin. This suggests a crosstalk of melatonin and H2S in protecting heat stress-induced photosynthetic inhibition via regulation of carbohydrate metabolism.

Previous studies reported the physical, transcriptomics and metabolomics changes in in-vitro acute heat stressed bovine granulosa cells. Granulosa cells exhibited transient proliferation senescence, oxidative stress, increased rate of apoptosis, and decline in steroidogenic activity. This study performs joint integration and network analysis of metabolomics and transcriptomics data to further narrow down and elucidate the role of differentially expressed genes, important metab-olites and relevant cellular and metabolic pathways in acute heat-stressed granulosa cells. Among significant (Raw P-value <0.05) metabolic pathways where metabolites and genes did converge, this study found Vitamin B6 metabolism, Glycine, serine and threonine metabolism, Phenylalanine metabo-lism, Arginine biosynthesis, Tryptophan metabolism, Arginine and proline metabolism, Histidine metabolism, and Glyoxylate and dicarboxylate metabolism. Important significant convergent bio-logical pathways included, ABC transporters and Protein digestion and absorption, while func-tional signaling pathways included cAMP, mTOR, and AMPK signaling pathways together with Ovarian steroidogenesis pathway. Among caner pathways, the most important pathway was Central carbon metabolism in cancer. Through multiple analysis query, Progesterone, Serotonin, citric acid, Pyridoxal, L-Lysine, Succinic acid, L-Glutamine, L-Leucine, L-Threonine, L-Tyrosine, Vitamin B6, Choline, and CYP1B1, MAOB, VEGFA, WNT11, AOX1, ADCY2, ICAM1, PYGM, SLC2A4, SLC16A3, HSD11B2 and NOS2 appeared to be important enriched metabolites and genes, respectively. These genes, metabolites, metabolic, cellular and cell signaling pathways com-prehensively elucidate the mechanisms underlying the intricate fight between death and survival in acute heat-stressed bovine granulosa cells, and essentially help further our understanding and future quest of research in this direction.

The plate fin heat exchanger is the compact heat exchanger applied in many industries because of its high thermal performance. To enhance the heat transfer of plate fin heat exchanger in further, three new kinds of wavy plate fins, namely perforated wavy fin, staggered wavy fin and discontinuous wavy fin are proposed and investigated by CFD simulations. The effects of key design parameters, including that of waviness aspect ratios, perforation diameters, stagger ratios and breaking distance are investigated, respectively, with the Reynolds number changes from 500 to 4500. It is found that due to the swirl flow and efficient mixing of fluid, the perforation, serration and breaking techniques are beneficial for the enhancement of heat transfer compared to the traditional wavy fin. At the same time, serration is beneficial to reduce the friction factor, and the breaking technique can reduce heat transfer area as well as enhance heat transfer performance. Through the performance evaluation criteria, the staggered wavy fin has an advantage over the small waviness aspect ratio compared to the perforated wavy fin. The maximum performance evaluation criteria (PEC), as high as 1.24, can be obtained for the perforated wavy fin at the largest waviness aspect ratio.

Specific climate adaptation and resilience measures can be efficiently designed and implemented at the regional and local level. Climate and environmental databases are of critical importance to achieving sustainability goals (SDGs) and for the efficient planning and implementation of suitable mitigation measures: Available databases can serve municipalities as a vital starting points to determine requirements, prioritize resources and allocate investments under consideration of commonly tight budget restrictions. High-quality geo, climate and environmental data are now available – data from remote sensing, i.e. Copernicus services will be of crucial importance. Forward-looking approaches exist to using such data to derive forecasts for urban planning process optimization for municipal administrations. On municipal level, however, the existing data have so far only been used to a limited extent, since there are no practical tools for urban planning that can be used to merge and meaningfully combine remote sensing data with local data and to further process and apply in municipal planning processes. Therefore, our project CoKLIMAx aims at the development of new digital products, advanced urban services and procedures, such as the development of practice-oriented technical tools that acquire various remote sensing and in-situ data sets for validation and further processing.

District heating networks have become widespread due to their ability to distribute thermal energy efficiently, which leads to reduced carbon emissions and improved air quality. The characteristics of these networks vary remarkably depending on the urban layout and system amplitude. Moreover, extensive data about the energy distribution and thermal capacity of different areas are seldom available. Design, optimization and control of these systems are enabled by the availability of fast and scalable models of district heating networks. This work addresses this issue by proposing a novel method to develop a scale-free model of large-scale district heating networks. Starting from coarse data available at the main substations, a physics-based model of the system aggregated regions is developed by identifying the heat capacity and heat loss coefficients. The model validation on the network of Västerås, Sweden, shows compatibility with literature data and can therefore be exploited for system design, optimization and control-oriented applications. In particular, the possibility to estimate the heat storage potential of network regions allows new smart management strategies to be investigated.

The shape memory alloys belong to the smart materials thanks to their thermomechanical proprieties' reply to thermal or to mechanical loading. These materials can change shape, stiffness, displacement, natural frequency, and many mechanical characteristics in response to stress or to heat such as conduction, convection or radiation. However, heating by convection or conduction are the most useful and studied methods unlike radiation. Therefore, this paper aims to study the radiation effect on the shape memory alloy behavior

As the first time, 0D-1D-3D and fully 3D steady-state aero-thermo-fluid simulations of a structural oil-to-air Fan Outlet Guide Vane Cooler (FOGVC) in a jet engine are presented. Using the commercial softwares Ansys Fluent, the thermo-mechanical module of Ansys and the 1D fluid solver Flownex, 5 simulation types (3D fully conjugate heat transfer with and without a thin wall model, 3D with a thin wall model, 1D-3D coupled, 1D and 0D) corresponding to 4 levels of simplification in 3 possible domains (oil, oil-metal and oil-metal-air) have been compared to provide selection criteria when a determined level of accuracy in the simulations without prohibited computational times is desired. The methodologies are applied to two different oil internal cavities: an inverted U with rectangular cross section and a coil internal cavity with a circular cross section. The obtained results show that depending on the scope of the research (outlet oil temperature, dissipated heat rate or oil pressure drop) and the accuracy of the results, one method or the other may be used. Experimental data would be needed to validate the numerical results by all employed methodologies and geometries.

The main purpose of bovine colostrum, being the milk secreted by a cow after giving birth, is to transfer passive immunity to the calf. The calves have an immature immune system as they lack immunoglobulins (Igs). Subsequently, the supply of good quality bovine colostrum is required. The quality of colostrum is classified by low bacterial counts and adequate Ig concentrations. Bacterial contamination can contain a variety of human pathogens or high counts of spoilage bacteria, which becomes more challenging with emerging use of bovine colostrum as food and food supplements. There is also a growing risk for the spread of zoonotic diseases originating from bovines. For this reason, processing based on heat treatment or other feasible techniques are required. This review provides an overview of literature on the microbial quality of bovine colostrum and processing methods to improve its microbial quality and keep its nutritional values as food. The highlights of this review are: high quality colostrum is a valuable raw material in food products and supplements, the microbial safety of bovine colostrum is increased using appropriate processing-suitable effective heat treatment, which does not destroy the high nutrition value of colostrum, the heat treatment processes are cost-effective compared to other methods, and heat treatment can be performed in both small- and large-scale production.

Cities worldwide are facing ever-increasing pressure to develop mitigation strategies for all sectors to deal with the impacts of climate change. Cities are expected to house 70% of the world’s population by 2050 and developing related resilient health systems is a significant challenge. Because of their physical nature, cities’ surface temperatures are often substantially higher than that of the surrounding rural areas, generating the so-called Urban Heat Island (UHI) effect. Whilst considerable emphasis has been placed on strategies to mitigate against the UHI-associated negative health effects of heat and pollution, the World Health Organization estimates that one of the main consequences of global warming will be an increased burden of such vector-borne diseases. Many of the major mosquito-borne diseases are urban and thus the global population exposed to these pathogens will steadily increase. Mitigation strategies beneficial for one sector may, however, be detrimental for another. Implementation of inter-sectoral strategies that can benefit many sectors (such as water, labour and health) do exist and would enable optimal use of the meagre resources available. Discussion among inter-sectoral stakeholders should be actively encouraged.

A non-Newtonian fluid model is used to investigate the two-dimensional pulsatile blood flow through a tapered artery with a stenosis. The mixed convection effects of heat and mass transfer are also taken into account. By applying non-dimensionalization and radial coordinate transformation, we simplify the system in a tube. Under the finite difference scheme, numerical solutions are calculated for velocity, temperature concentration, resistance, impedance, wall shear stress and shearing stress at the stenosis throat. Finally, Quantitative analysis is carried out.

Extracellular vesicles (EV) released by tumor cells are a major aspect of the resistance-associated secretory phenotype (RASP), by which immune evasion can be established. Heat shock proteins (HSPs) are an evolutionarily conserved family of molecular chaperones, which stabilize proteins, minimize protein misfolding and aggregation within the cell, besides facilitating protein translocation, refolding and degradation. (i) Releases of extracellular HSPs (ex-HSP) and EV-associated HSPs (EV-HSP) are essential in RASP, by which molecular cotransfer of HSPs with oncogenic factors into recipient cells can promote cancer progression and resistance against stress such as hypoxia, radiation, chemicals, and immune system. (ii) RASP of tumor cells can eject anticancer drugs, molecularly targeted therapeutics, and immune checkpoint inhibitors with EVs. (iii) Cytotoxic lipids can be also released from tumor cells as RASP. Nevertheless, ex-HSP and EV-HSP can play immunostimulatory and immunosuppressive roles by binding to receptors such as LRP1/CD91/A2MR, scavenger receptors, and toll-like receptors expressed on recipient cells. Liquid biopsy of HSPs in body fluids may be useful in diagnosis, prognosis, and treatment in cancer. Regarding HSP90-targeted therapeutics, we summarize the pros, cons, and problem solutions in this review. Although production of HSPs are canonically induced by heat shock factor 1 (HSF1) and hypoxia-inducible factor 1 (HIF-1), recent studies discovered that production of HSPs is also regulated by matrix metalloproteinase 3 (MMP3) and heterochromatin protein 1 (HP1) and production of cochaperone CDC37 is reciprocally regulated by myeloid zinc finger 1 (MZF1) and SCAN-D1.

COVID-19 is one of the deadliest respiratory diseases, and its emergence caught the pharmaceutical industry off guard. While vaccines have been rapidly developed, treatment options for infected people remain scarce, and COVID-19 poses a substantial global threat. This study presents a novel workflow to predict robust druggable targets against emerging RNA viruses using metabolic networks and information of the viral structure and its genome sequence. For this purpose, we implemented pymCADRE and PREDICATE to create tissue-specific metabolic models, construct viral biomass functions and predict host-based antiviral targets from more than one genome. We observed that pymCADRE reduces the computational time of flux variability analysis for internal optimizations. We applied these tools to create a new metabolic network of primary bronchial epithelial cells infected with SARS-CoV-2 and identified enzymatic reactions with inhibitory effects. The most promising reported targets were from the purine metabolism, while targeting the pyrimidine and carbohydrate metabolisms seemed to be promising approaches to enhance viral inhibition. Finally, we computationally tested the robustness of our targets in all known variants of concern, verifying our targets’ inhibitory effects. Since laboratory tests are time-consuming and involve complex readouts to track processes, our workflow focuses on metabolic fluxes within infected cells and is applicable for rapid hypothesis-driven identification of potentially exploitable antivirals concerning various viruses and host cell types.

We present an overview over eight brightly luminescent Cu(I) dimers of the type Cu2X2(PN)3 with X = Cl, Br, I and P^N = 2-diphenylphosphino-pyridine (Ph2Ppy), 2-diphenylphosphino-pyrimidine (Ph2Ppym), 1-diphenylphosphino-isoquinoline (Ph2Piqn) including three new crystal structures (Cu2Br2(Ph2Ppy)3, 1-Br, Cu2I2(Ph2Ppym)3, 2-I, and Cu2I2(Ph2Piqn)3, 3-I). However, we mainly focus on their photo-luminescence properties. All compounds exhibit combined thermally activated delayed fluorescence (TADF) and phosphorescence at ambient temperature. Emission color, decay time, and quantum yield varies over large ranges. For deeper characterization, we select Cu2I2(Ph2Ppy)3, 1-I, showing a quantum yield of 81 %. DFT and SOC-TDDFT calculations provide insight into the electronic structures of the singlet S1 and triplet T1 states. Both stem from metal+iodide-to-ligand charge transfer transitions. Evaluation of the emission decay dynamics, measured from 1.2 ≤ T ≤ 300 K, gives ∆E(S1-T1) = 380 cm-1 (47 meV), a transition rate of k(S1→S0) = 2.25×106 s-1 (445 ns), T1 zero-field splittings, transition rates from the triplet substates, and spin-lattice relaxation times. We also discuss the interplay of S1-TADF and T1-phosphorescence. The combined emission paths shorten the overall decay time. For OLED applications, utilization of both singlet and triplet harvesting can be highly favorable for improvement of the device performance.

The present article is dealing with the state of question about building-energy monitoring systems used for data collection to estimate the Heat Lost Coefficient (HLC) with existing methods and so determinate buildings’ Envelope Energy Performance (EEP). In addition, the data requirements of HLC estimation methods are related with commonly used methods for fault detection, calibration and supervision of energy monitoring systems in buildings. Based on an extended review of experimental tests since 1978, a qualitative and quantitative analysis of Monitoring and Controlling System (MCS) specifications has been carried out. Although most actual Buildings Automation Systems (BAS) may measure the required parameters, further research is still needed to ensure that these data are accurate enough to rigorously apply the HLC estimation methods.

Heat stress affects the yield of medicinal plants and can reduce biomass and/or metabolite production. In order to evaluate the effect of heat-induced stress on the essential oil production in Mentha x piperita L. var. Mitcham (Mitcham mint) and Mentha x arvensis var. piperascens Malinv. ex L. H. Bailey (Japanese mint), we studied the chemical composition of the oils of the two mint species under different heat shock stress in growth chambers. The antibacterial activity of the essential oils was also evaluated; microscopic observation (fluorescence and electron transmission) was used to assess the effect of the tested samples on bacterial growth. The results obtained shed light on the mint essential oils composition and biological activity in relation to heat stress.

The impact of snow darkening by deposition of light absorbing aerosols (LAAs) on snow cover over the Himalaya-Tibetan-Plateau (HTP) and influence on the Asian monsoon are investigated using the NASA Goddard Earth Observing System Model Version 5 (GEOS-5). We find that during April-May-June, deposition of LAAs on snow leads to a reduction in surface albedo, initiating a sequence of feedback processes, starting with increased surface solar radiation, rapid snowmelt in HTP and warming of the surface and upper troposphere, followed by enhanced low-level southwesterlies and increased dust loading over the Himalayas-Indo-Gangetic Plain. The warming is amplified by increased dust aerosol heating, and subsequently amplified by latent heating from enhanced precipitation over the Himalaya foothills and northern India, via the Elevated Heat Pump (EHP) effect during June-July-August. The reduced snow cover in the HTP anchors the enhanced heating over the Tibetan Plateau and its southern slopes, in conjunction with an enhancement of the Tibetan Anticyclone, and the development of an anomalous Rossby wavetrain over East Asia, leading to weakening of the subtropical westerly jet, and northward displacement and intensification of the Mei-Yu rainbelt. Our results suggest that atmosphere-land heating by LAAs, particularly desert dust play a fundamental role in physical processes underpinning the snow-monsoon relationship proposed by Blandford more than a century ago.

Tumor cells exhibit a resistance-associated secretory phenotype involving extracellular vesicles (EVs) and heat shock proteins (HSPs). This response occurs in response to cell stress and cancer therapeutics. HSPs are stress-responsive molecular chaperones promoting proper protein folding, while also being released from cells with EVs as well as in free form as alarmins. We have here investigated the secretory phenotype of castration-resistant prostate cancer (CRPC) cells using proteome analysis. We have also examined the roles of the key co-chaperone CDC37 in stressome release, epithelial-to-mesenchymal transition (EMT), and tumor progression. A number of HSP family members and their common receptor CD91/LRP1 were enriched at high levels in CRPC cell-derived EVs among over 700 other protein species. The small EVs (30 to 200 nm in size, potentially exosomes) were released even in a non-heated condition from the prostate cancer cells, whereas EMT-coupled release of EVs (200 to 500 nm, likely ectosomes) with associated HSP90α was increased after heat shock stress (HSS). Lactate dehydrogenase, a marker of membrane leakage/damage of cells, was also released upon HSS from the prostate cancer cells. During this stress response, intracellular CDC37 was also transcriptionally inducible by heat shock factor 1, and knockdown of CDC37 decreased EMT-coupled release of EVs. Triple knockdown of CDC37, HSP90α, and HSP90β was required for efficient reduction of the chaperone trio and to reduce tumorigenicity of the CRPC cells in vivo. Taken together, the data indicated that CDC37 and HSP90 are essential for stressome release and for tumorigenesis in resistant cancer.

Tumor-associated macrophages are a key component in the tumor microenvironment, secreting extracellular vesicles (EVs) such as exosomes and other various factors for intercellular communication. However, macrophage-derived EVs heterogeneity and their cytotoxicity to cancer cells has not been well understood. Here, we aimed to separately isolate various types of macro-phage-EVs by size exclusion chromatography (SEC) method and investigate EV transmission and cytotoxicity to oral cancer cells. For fluorescence-labeling of cellular and EV membranes, palmitoylation signal-fused GFP and tdTomato were expressed in THP-1 monocytic cells and HSC-3 oral cancer cells, respectively. We found that fluorescence-labeled EVs secreted by macrophages were highly transmissive to oral cancer cells than those from parental monocytic cells. In a co-culture system and conditioned medium (CM), a macrophage-secreted unidentified factor was cytotoxic to oral cancer cells. We fractionated macrophage-derived EVs by the SEC method and performed western blotting to characterize various EV types. Three fractions were characterized: small exosomes (EXO-S: < 50 nm) fraction containing HSP90α, HSP90β, CD63 (EV marker) and β-actin; large exosomes (EXO-L: 50-200 nm) fraction containing CD9 (EV marker) and HSP90β; large EVs (100-500 nm) fraction. Notably, the macrophage-derived small exosomes fraction was cytotoxic to oral cancer cells, while large exosomes and large EVs were not. There-fore, it was implicated that macrophage-derived small exosomes are cytotoxic with high trans-mission potential to cancer cells.

Antimony (Sb) Substitution less than 10 % is examined on a single crystal of a layered superconductor NdO_0.7F_0.3BiS₂. Superconducting transition temperature of the substituted samples decreases with increasing Sb concentration. A lattice constant along the c axis showed a large decrease compared with that along the a axis. Since in-plane chemical pressure monotonically decreases with increasing Sb concentration, the suppression of the superconductivity is well described in terms of the decrease in in-plane chemical pressure.

This study aims to investigate the hydration and strength characteristics of green cementitious mortars with ultrahigh-volume limestone-calcined clay as well as two kinds of Class F fly ash. Using the ASTM C311 strength activity index test method, the effect of different pozzolan replacement levels of cement (0%, 20%, 50%, and 80%, by weight) were investigated. Compressive strength at 3, 7, 14, 28 and 90 days under standard curing was recorded, and hydration heat of the 20% and 80% replacement mixes was studied using iso-thermal calorimetry. It was observed that the effectiveness of the pozzolan in mortars depends on particle size distribution, glassy or amorphous nature, surface area and replacement level. The sum of all these effects can be captured by the strength activity test only if the standard recommended 20% pozzolan mix is substituted with the actual mix composition. The results in this study provide insights into the mix design and applications of ultrahigh-volume pozzolanic cementitious materials specifically made with limestone-calcined clay, and promote greener cement and concrete in construction industry.

Thermal energy storage (TES) is a key technology to enhance the efficiency of energy systems as well as to increase the share of renewable energies. In this context, the present paper reports a literature review of the recent advancement in the field of adsorption TES systems. After a first introduction about different heat storage technologies, the adsorption TES working principle is explained and compared to the other technologies. Subsequently, promising features and critical issues at material, component and system levels are deeply analyzed and the ongoing activities to make this technology ready for marketing are introduced.

Rapid and extensive urbanization has adversely impacted humans and ecological entities in the recent decades through a decrease in surface permeability and the emergence of urban heat islands (UHI). While detailed and continuous assessments of surface permeability and UHI are crucial for urban planning and management of landuse zones, they have mostly involved time consuming and expensive field studies, and single sensor derived large scale aerial and satellite imageries. We demonstrated the advantage of fusing imageries from multiple sensors for landuse and landcover (LULC) change assessments as well as for assessing surface permeability and UHI emergence in Tirunelveli, Tamilnadu, India. Cartosat-2 and Landsat-7 ETM+ imageries from 2007 and 2017 were fused and classified using a Rotation Forest (RF), while surface permeability and temperature were quantified using Soil-Adjusted Vegetation Index (SAVI) and Land Surface Temperature (LST) index, respectively. Fused images exhibited higher classification accuracies than non-fused images, i.e. overall kappa coefficient values 0.83 and 0.75, respectively. We observed an overall increase of 20 km2 (45%) in the coverage of urban (dry, real estate plots and built-up) areas, while a decrease of 27 km2 (37%) for vegetated (cropland and forest) areas in Tirunelveli between 2007 and 2017. The SAVI values indicated an extensive decrease in surface permeability for Tirunelveli overall (0.4) and also for almost all LULC zones. The LST values exhibited an associated overall increase (1.30C) of surface temperature in Tirunelveli with the highest increase (2.40C) for urban built-up areas between 2007 and 2017. The SAVI-LST combined metric depicted the Southeastern built-up areas in Tirunelveli as a potential UHI hotspot, while a caution for the Western riparian zone for UHI emergence in 2017. Our results provide important metrics for surface permeability and UHI monitoring, and inform urban and zonal planning authorities about the advantages of satellite image fusion.

The Urban Heat Island (UHI) is one of the more serious consequences of urbanization resulting in impacts on thermal comfort levels, heat stress, and even mortality. For Municipal Beirut, implementation of “cool” surface materials and green spaces have been recommended to counterbalance the UHI. This paper builds on previous findings on the topic of non-constructible parcels within the district of Bachoura in Municipal Beirut and examines the possibility of implementing “cool” surface or paving materials and urban vegetation which can improve thermal conditions especially during the summer period and with the viewto project the positive findings of this case study to the entire Municipal Beirut area. A numerical analysis using ENVI-met 4.0 investigates the thermal performance of these non-constructibles further to implementation of high reflective surfaces and urban vegetation within a broad neighborhood scale in Bachoura. Results show reductions in ambient temperatures up to 1K on a summer day.. Within the framework of an integrated approach to planning, this form of urban acupuncture aims for substantial UHI reduction. Energy performance of buildings further to implementation of these mitigation measures is also recommended for future studies and to validate the findings in this paper.

This study aims to identify an optimal heat-treatment parameter set for an additively manufactured AlSi10Mg alloy in terms of increasing the hardness and eliminating the anisotropic microstructural characteristics of the alloy in as-built condition. Furthermore, the influence of these optimized parameters on the fatigue properties of the alloy investigated. In this respect, microstructural characteristics of an AlSi10Mg alloy manufactured by Laser-Based Powder Bed Fusion in non-heat-treated and heat-treated conditions were investigated. Their static and dynamic mechanical properties were evaluated, and fatigue behavior was explained by a detailed examination of fracture surfaces. Much of the microstructure in the non-heat-treated condition was composed of columnar grains oriented parallel to the build direction. Further analysis revealed a high fraction of pro-eutectic α-Al. Through heat-treatment, the alloy was successfully brought to its peak-hardened condition, while eliminating the anisotropic microstructural features. Yield strength and ductility increased simultaneously after heat-treatment, which is due to the relief of residual stresses, preservation of refined grains, and introduction of precipitation strengthening. The fatigue strength, calculated at 10^7 cycles, improved as well after heat-treatment and finally detailed fractography reviled that a more ductile fracture mechanism has happened in the heat-treated condition compared to the non-heat-treated condition.

In the present work, a superlattice structure comprising superconducting and insulator layers is studied. Here, if a magnetic field is applied parallel to the layers, the lack of a pinning center leads to a novel transition; in particular, as the applied magnetic field is reduced, the stationary wave surrounding the magnetic flux quantum in the superconducting layer eventually collides with the superconducting–insulating interfaces on both sides because its radius becomes larger than the width of the superconducting layer. At this instant, the stationary wave will collapse, and a transition will occur: the magnetic quanta are collapsed and thus the uniform magnetic field distribution is achieved, which corresponds to the transition from the superconducting state to the normal state over critical current. Considering a one-dimensional model of the structure, a critical current density equation is derived that indicates an increase in the critical current density for increased applied magnetic field. Subsequently, the same calculation was conducted after changing the direction of the magnetic field component, and the combination of these two calculations expresses the anisotropic property of the structure. The phenomenon is also predicted for anisotropic critical current density. This phenomenon is an important discovery that helps manufacture high-temperature superconducting tape as well as large high-temperature superconducting coils.

Plants thriving in desert environments are suitable for studying mechanisms for plant survival under extreme seasonal climate variation. Zygophyllum dumosum Boiss, like many other Zygophyllaceae species, displays a unique epigenetic mechanism whereby the repressive markers di- and tri-methyl of H3K9 do not exist. We studied epigenetic mechanisms underlying seasonal growth cycles in Z. dumosum and their association with factors regulating basic cell functions. We showed strong association between rainfall and seasonal growth and the epigenetic marker of dimethyl H3K4, which disappears on entry into the dry season and the acquisition of dormant state. DNA methylation is not affected by lack of H3K9 di and tri methyl and changes in methylation pattern are apparent on entry into the dry season. Proteome analysis of acid soluble fractions revealed extensive reduction in ribosomal proteins and in proteins involved in chloroplasts and mitochondria activities during the dry seasons concomitantly with up-regulation of molecular chaperone HSPs. Our results highlight mechanisms underlying Z. dumosum adaptation to seasonal climate variation. Particularly, summer dormancy is associated with loss of the permissive epigenetic marker dimethyl H3K4, which might facilitate genome compaction, concomitantly with significant reduction in proteins involved in basic cell functions (i.e., protein synthesis, photosynthesis and respiration).

One of the most destructive natural disasters is the earthquake which brings enormous risks to humankind. The objective of the current study was to determine the Earthquake’s remote sensing multiparameter (i.e. land surface temperature (LST), air temperature, specific humidity, precipitation and wind speed) spatiotemporal anomaly of many earthquake samples occurred during 2018 around the world. In this research 11 earthquake (M > 6:0) studied (4 samples selected in a land with transparent sky situations, 3 samples in land within cloudy situations and 4 samples in marine earthquakes). The interquartile range (IQR) and mean ± 2σ methods utilized to improve the efficiency of anomalous differences. As a result, based on the IQR method, negative anomaly before the event detected during the daytime in Mexico and during the nighttime in Afghanistan. In addition, a negative outlier of brightness temperature (BT) detected in Alaska before, after and during the event. In contrast, based on IQR and mean ± 2σ positive anomaly detected in precipitation before and after the event in all investigated examples. According to mean ± 2σ, negative anomaly LST, specific humidity, sea surface temperature (SST_100) and wind detected in most examined earthquake samples. In contrast, positive SST_0 anomaly observed in Fiji and Honduras after the earthquake. Our results suggested in marine earthquakes, for earthquake forecasting we can merge a prior negative anomaly in the wind speed and SST_100. Regarding the in land cloudy sky earthquakes, merging anomaly parameters could be the negative prior anomaly in BT, skin temperature, in contrast, a positive anomaly in precipitation. In land transparent sky earthquake, usually negative prior anomalies in air temperature, specific humidity and LST.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

The Japanese Association for Acute Medicine Committee recently proposed a novel classification system for the severity of heat-related illnesses. The illnesses are simply classified into three stages based on symptoms and management or treatment. Stages I, II, and III broadly correspond to heat cramp and syncope, heat exhaustion, and heat stroke, respectively. Our objective was to examine whether this novel severity classification is useful in the diagnosis by healthcare professionals of patients with severe heat-related illness and organ failure. A nationwide surveillance study of heat-related illnesses was conducted between June 1 and September 30, 2012, at emergency departments in Japan. Among the 2130 patients who attended 102 emergency departments, the severity of their heat-related illness was recorded for 1799 patients, who were included in this study. In the patients with heat cramp and syncope or heat exhaustion (but not heat stroke), the blood test data (alanine aminotransferase, creatinine, blood urea nitrogen, and platelet counts) for those classified as stage III were significantly higher than those of patients classified as stage I or II. There were no deaths among the patients classified as stage I. This novel classification may avoid underestimating the severity of heat-related illness.

Imaging techniques such as computed tomographies (CT) play a major role in clinical imaging and diagnosis of malignant lesions. In recent years, spectral CT has emerged in the field of computed tomographies, utilizing detailed information from extracted spectral parameters of the specimen. Metal nanoparticle platforms enable effective payload delivery for this technique. Due to the possibility of surface modification, metal nanoparticles are predestined to facilitate molecular tumor targeting. In this work, we demonstrate the feasibility of anti-plasma membrane Heat shock protein 70 functionalized gold nanoparticles (AuNPs) for tumor specific multimodal imaging. Membrane-associated Hsp70 is exclusively presented on the plasma membrane of malignant cells of multiple tumor entities, but not on corresponding normal tissue cells, predestining this target epitope for tumor-selective in vivo targeting. In vitro microscopical analysis revealed the presence of cmHsp70.1-AuNP in the cytosol of tumor cell lines, being internalized via the endosomal-lysosomal pathway. In tumor bearing mice the biodistribution as well as the intratumorally enrichment of AuNP were examined 24h after i.v. application, in vivo. In parallel to spectral CT analysis, histological analysis confirmed the presence of tumor cells. In contrast to control NP, a significant enrichment of cmHsp70.1-AuNPs has been detected selectively in tumors of different preclinical mouse models. Furthermore, the biodistribution of AuNP, following i.v. injection, was analyzed by a machine-learning approach on digitalized slides. In summary, utilizing mHsp70 on tumor cells for guidance of cmHsp70.1 antibody functionalized nanoparticles enables sufficient enrichment and uniform distribution of AuNPs in mHsp70-expressing tumor cells, adequate for various microscopical imaging techniques and spectral-CT-based tumor delineation, in vivo.

The use of different primary energy sources in human society has led to two major polluting emissions in the environment: energy (mostly heat), and chemical substances (mostly carbon dioxide). In this paper, the total global anthropogenic emissions of heat to the atmosphere during the industrial era (years 1850-2018) were determined and their effect on the change of global atmospheric temperature was calculated. The concept of a theoretical three-phase Earth reactor was introduced to estimate global atmospheric temperature increase caused by anthro-pogenic heat emissions. The resulting calculations closely approximated the actual atmospheric temperature change recorded during the last 170-year period. These results suggest that the temperature change of the atmosphere (global warming) is entirely due to anthropogenic heat emissions.

Laboratory experiments and natural phenomena investigations in this research series experimentally revealed the existence of gravitational repulsion force dependent on thermal energy content, pervading our surroundings both microscopically and macroscopically. This paper presents an alternative mathematical model of both gravitational repulsion and attraction forces between two gaseous molecules, validated by experimental data. The model is self-standing and independent of existing models built on idealistic assumptions. While existing models considered gravitational interaction as a single force, the presented experimental model considers it the resultant of two distinct forces: gravitational repulsion and attraction. When established experimental data on nitrogen, hydrogen, oxygen, water vapor, carbon monoxide and carbon dioxide were applied, the model performed, both analytically and experimentally: (1) confirming the existence of both gravitational repulsion and attraction forces among gas molecules, (2) demonstrating that the two forces follow Inverse-Cube relationship with the distance between molecules, (3) revealing that repulsion force is linearly proportional to the absolute temperature, thus filling the critical gap between energy and fundamental forces. Orders of magnitude of gravitational repulsion and attraction forces are very large compared to the gravitational force between gas molecules calculated according to the classical theory, enabling manipulation to achieve hitherto unknown outcomes and developments.

proposal for a fundamental theory is described in which classical and quantum physics as a representation of the universe as a gigantic dendrogram are unified. The latter is the explicate order structure corresponding to the purely number-theoretical implicate order structure given by p-adic numbers. This number field was zero-dimensional, totally disconnected, and disordered. Physical systems (such as electrons, photons) are sub-dendrograms of the universal dendrogram. Measurement process is described as interactions among dendrograms; in particular, quantum measurement problems can be resolved using this process. The theory is realistic, but realism is expressed via the the Leibnitz principle of the Identity of Indiscernible. The classical-quantum interplay is based on the degree of indistinguishability between dendrograms (in which the ergodicity assumption is removed). Depending on this degree, some physical quantities behave more or less in a quantum manner (versus classic manner). Ideologically, our theory is very close to Smolin’s dynamics of difference and Rovelli’s relational quantum mechanics. The presence of classical behavior in nature implies a finiteness of the Universe-dendrogram. (Infinite Universe is considered to be purely quantum.) Reconstruction of events in a four-dimensional space type is based on the holographic principle. Our model reproduces Bell-type correlations in the dendrogramic framework. By adjusting dendrogram complexity, violation of the Bell inequality can be made larger or smaller.

The objective of this study was to evaluate biomarkers of heat stress (HS) from automatic milking system (AMS), the relationships between measurements of temperature-humidity index (THI) and reticulorumen ph and temperature and some automatic milking systems parameters in dairy cows (rumination time (RT), milk traits, body weight (BW) and consumption of concentrate (CC)) during summer period. The experiment was carried out on a dairy farm at 54.9587408, 23.784146. Lithuanian Black and White dairy cows (n=365) were selected. The cows were milked with Lely Astronaut® A3 milking robots with free traffic. The rations were calculated to meet physiological requirements of the animals. Daily milk yield, rumination time, body weight, milk fat and protein ratio were collected from the Lely T4C management program for analysis. The pH and temperature of the contents of cow reticulorumen were measured using specific smaX-tec boluses manufactured for animal care. The daily humidity and air temperature in the farm zone were obtained from the adjacent weather station (2 km away). According this study during HS, the higher THI had positive correlation with ML, which show tendencies to increase risk of mastitis, and decrease CC, RT, BW, MY, reticulorumen ph and F/P. Some biomarkers of HS can be milk yield, milk lactose, somatic cell count, concentrate conception, rumination time, body weight, reticulorumen ph and milk fat – protein ratio. We can recommend to monitoring these parameters in the herd management program to identify possibility of heat stress.

A topological quantum interplay between the magnetic flux and the mass has been investigated, for the case of an electron, by evaluating a gauge-invariant phase factor (a Wilson loop) linked to the electromagnetic gauge field of the particle. In particular, from this phase factor and the quantization of the magnetic flux variations, a relationship between the mass at rest of the electron and its self-energy , arising from radiative corrections, has been obtained also within a QED approach. Besides, a formulation of an energy scale comparable to the energy at rest of an electron-positron pair is proposed. Remarkably, a reckoning of the Bohr energy of a W⁺ W^- pair is compatible with constants and parameters usually employed within the electroweak theory and comparable to the energy at rest of an electron-positron pair.

The classical propositional calculus (zero-order logic, classical propositional logic), is the most fundamental two-valued logical system. In this paper we present a proof of inconsistency of the classical propositional calculus. Then, we get right away the conclusion that the metatheory of the classical propositional calculus is inconsistent.

Resistant cancer often shows a particular secretory trait such as heat shock proteins (HSPs) and extracellular vesicles (EVs), including exosomes and oncosomes surrounded by lipid bilayers. Lipoproteins are biochemical assemblies that transport hydrophobic lipid (a.k.a. fat) molecules in body fluid and are composed of a single-layer phospholipid and cholesterol outer shell, lipids molecules within the particles, and apolipoproteins embedded in the membrane. However, lipoprotein storage and secretion by cancer cells have not well-investigated yet. We found lipoproteins were stored and abundantly secreted by neuroendocrine, castration-resistant prostate cancer (NEPC / CRPC) cells but barely secreted by colon cancer cells and oral squamous cell carcinoma (OSCC) cells. In addition, large EVs (approx. 300 nm diameter) and potential oncosomes were released by CRPC and OSCC cells. Proteomics revealed that CRPC cells secreted EVs enriched with tetraspanins and extracellular matrices which were reduced upon heat shock stress and alternatively lipoproteins and HSPs were secreted upon stress. Heat shock stress triggered secretion of lipoprotein-EV complexes that contained apolipoprotein A, B, C and E. These data suggested that vesicular assembly composed of EVs and lipoproteins enriched with cholesterols and phospholipids may be stored in resistant cancer cells but released upon cell stress that is increased in cancer therapies.

The current SARS-CoV-2 pandemic is still threatening humankind. Despite first successes in vaccine development and approval, no antiviral treatment is available for COVID-19 patients. The success is further tarnished by the emergence and spreading of mutation variants of SARS-CoV-2, for which some vaccines are not effective anymore. This highlights the urgent need for antiviral therapies even more. This article describes how the Genome-Scale Metabolic Model (GEM) of the host-virus interaction of human alveolar macrophages and SARS-CoV-2 was refined by incorporating the latest information about the virus’s structural proteins and the mutant variants B.1.1.7 and B.1.351. We confirmed the initially identified guanylate kinase as a potential antiviral target with this refined model and identified further potential targets from the purine and pyrimidine metabolism. The model was further extended by incorporating the virus’ lipid requirements. This opened new perspectives for potential antiviral targets in the altered lipid metabolism. Especially the phosphatidylcholine biosynthesis seems to play a pivotal role in viral replication. The guanylate kinase is even a robust target in all investigated mutation variants currently spreading worldwide. These new insights can guide laboratory experiments for the validation of identified potential antiviral targets. Only the combination of vaccines and antiviral therapies will effectively defeat this ongoing pandemic.

Objective On the eve of the summer Olympic Games in Tokyo research focus has shifted on the core temperature responses of elite athletes competing in the heat. In the absence of the field data of core temperature during Olympic sailing competition aim of the present study was to identify core temperature response during the Tokyo 2020 Olympic Test Event. Methods Four elite athletes from Olympic sailing (177.5±5.2 cm, 71.1±7.4 kg, body mass index 22.5±1.4 kg/m2, 24.8±3.7 yrs, VO2max 50.6±7.2 mL/min/kg)): 2 males and 2 females participated in the study. Core temperature was recorded using e-Celsius ingestible capsules, heart rate using a heart rate monitor. Ambient conditions in direct sunlight were measured using portable meteo station. Results Core temperature was recorded at water environment via an ingestible capsule in 4 sailors during the training (T), and competition (C), respectively. Ambient conditions in direct sunlight were hot and humid: during training temperature were 30.9°C±1.7°C and relative humidity 81.4%±2.8%, corresponding to a wet-bulb globe temperature of 41°C±4°C and during competition temperature was 31.2°C±2.3°C and relative humidity 87.2%±4.4%, corresponding to a wet-bulb globe temperature of 45.2°C±8.9°C. Core temperature increased during training reaching higher peak values (38.6°C±0.4°C) and during competition (38.9°C±0.4°C). The highest temperature recorded was 39.4°C (C). Conclusion The current study provides unique information into the core temperature parameters under heat stress in elite Olympic sailors during training and race event.

In this study, the effect of heat treatment was investigated to influence the occurrence of fracture during manufacturing process of Alloy B steel with boron contents as high as 130 ppm. As the content of boron increases, it affects the phase transformation temperature and texture. The development of {111}<uvw> components in the γ-fiber is affected depending on the austenite fraction after phase transformation. The Alloy B steel indicated that the increase in the boron content increased the α to γ phase transformation temperature such that sufficient transformation did not occur in the normalizing condition. The cracks occurred at the point of the transition from elastic to plastic deformation in the ND direction during the rolling process, thereby resulting in failure. Therefore, it is necessary to avoid the intermediate heat treatment condition in which γ-fiber does not fully develop, i.e., an imperfect normalization.

Uganda possesses natural rainforests that serve enormous environmental ecosystems and biodiversity services. Moreover, the country is known for its various tropical rainforest hardwoods, birds, and animal species. Over the years, the trend in the natural forest land has declined at an alarming rate; hence need to investigate the possible drivers. The loss of such biodiversity and ecosystems risks desertification and extreme climatic condition. As the world moves towards Zero Deforestation 2030, understanding the determinants of deforestation and forest degradation is paramount. Therefore, the main objective of this study was to understand the impact and relationships between net forest conversion, energy emission, agriculture, and forest production of Roundwood. We used data from FAO for the period 2004-2016. Using the ADF and KPSS test, we checked for the unit root presence in the variables. Also, the study used two different regression models: multiple linear regression and dynamic linear model. To analyze the determinants of deforestation, we used net forest conversion in Uganda. There was 94 % variation in the dependent variable (Net Forest conversion). The outcome of the dynamic linear regression showed that agriculture and energy emission positively impact net forest conversion. Based on our findings, this study recommended the modernization of agriculture by the government of Uganda to stop cutting down the forests on a big scale. Also, the study suggested that the government strictly legislate Roundwood and wood fuels/charcoal and firewood to reduce huge dependency on forests toward Zero-Deforestation by 2030. If well-structured and implemented, government policies could solve the unnecessary over dependency on the rainforest, the heart of the region's climatic conditions.

In the past two decades the world experienced an exceptional number of unprecedented extreme weather events, some causing major human suffering and economic damage, such as the March 2012 heat event, which was called “Meteorological March Madness.” From the beginning of space era a correlation of solar flares with pressure changes in atmosphere within 2–3 days or even less was reported. In this study we wanted to test the possible relation of highly warm weather events in North-East America with Solar Energetic Particle (SEP) events. For this reason we compared ground temperatures T_M in Madison, Wisconsin, with energetic particle fluxes P measured by the EPAM instrument onboard the ACE spacecraft. In particular, we elaborated case events and the results of a statistical study of the SEP events related with the largest (Dst ≤ −150nT) Coronal Mass Ejection (CME)-induced geomagnetic storms, between with the years 1997–2015. The most striking result of our statistical analysis is a very significant positive correlation between the highest temperature increase_. ΔT_M and the time duration of the temperature increase ΔT_M (r = 0.8, p <0.001) at “winter times” ( r = 0.5, p , 0.01 for the whole sample of 26 SEP examined events). The time response of T_M to P was found to be in general short (a few days), but in the case of March 2015, during a gradual P8 increase, a cross-correlation test indicated highest c.c. within 1 day (p < 0.05). The March 2012 “meteorological anomaly” was elaborated in the case of South-East Europe, where, beside a period of strong winds and rainfall (6-13.3.2012), intense precipitation in North-East Greece (Alexandroupoli) were found to be correlated with distinct high energy flux enhancements. A rough theoretical interpretation is discussed for the space—atmospheric extreme weather relationship we found. However, much work should be done to achieve early warning of space weather dependent extreme meteorological events. Such future advances in understanding the relationships between space weather and extreme atmospheric events would improve atmospheric models and help people’s safety, health and life.

All living cells maintain a charge distribution across their cell membrane (membrane potential) by carefully controlled ion fluxes. These bioelectric signals regulate cell behavior (such as migration, proliferation, differentiation) as well as higher-level tissue and organ patterning. Thus, voltage gradients represent an important parameter for diagnostics as well as a promising target for therapeutic interventions in birth defects, injury, and cancer. However, despite much progress in cell and molecular biology, little is known about bioelectric states in human stem cells. Here, we present simple methods to simultaneously track ion dynamics, membrane voltage, cell morphology, and cell activity (pH and ROS), using fluorescent reporter dyes in living human neurons derived from induced neural stem cells (hiNSC). We developed and tested functional protocols for manipulating ion fluxes, membrane potential, and cell activity, and tracking neural responses to wounding and re-innervation in vitro. Finally, using morphology sensor, we tested and quantified the ability of physiological actuators (neurotransmitters and pH) to manipulate nerve wound re-innervation. These methods are not specific to a particular cell type and should be broadly applicable to the study of bioelectrical controls across a wide range of combinations of models and endpoints.

We evaluated epidemiological evolution and economic impact of COVID-19 pandemic in the European Union (EU) and worldwide, and the effects of control strategies on them. We collected incidence, mortality, and gross domestic product (GDP) data between the first quarter of 2020 and of 2023. Then, we reviewed the effectiveness of the mitigation and zero-COVID control strategies. The statistical analysis was done calculating the incidence rate ratio (IRR) of two rates and its 95% confidence interval (CI). In the EU, COVID-19 presented six epidemic waves. The sixth one at the beginning of 2022 was the biggest. Globally, the biggest wave occurred at the beginning of 2023. Highest mortality rates were observed in the EU during 2020-2021 and globally at the beginning of 2021. In mitigation countries, mortality was much higher than in zero-COVID countries (IRR= 6.82; CI:6.14-7.60; p<0.001). A GDP reduction was observed worldwide, except in Asia. None of the eight zero-COVID countries presented a GDP growth percentage lower than the EU percentage in 2020, and 3/8 in 2022 (p=0.054). COVID-19 pandemic caused epidemic waves with high mortality rates and a negative impact on GDP. The zero-COVID strategy was more effective in avoiding mortality and potentially had less impact on GDP.

Neurological complications of infection by the mosquito-borne Zika virus (ZIKV) include Guillain-Barré syndrome (GBS), an acute inflammatory demyelinating polyneuritis. GBS was first associated with recent ZIKV epidemics caused by the emergence of ZIKV Asian lineage in South Pacific. Here, we hypothesize that ZIKV-associated GBS relates to a molecular mimicry between viral envelope E (E) protein and neural proteins involved in GBS. Analysis of ZIKV epidemic strains showed that glycan loop (GL) region of the E protein includes an IVNDT motif which is conserved in voltage-dependent L-type calcium channel subunit alpha-1C (Cav1.2) and Heat Shock 70 kDa protein 12A (HSP70 12A). Both VSCC-alpha 1C and HSP70 12A belong to protein families which have been associated with neurological autoimmune diseases in central nervous system. The purpose of our in silico analysis is to point out that IVNDT motif of ZIKV E-GL region should be taken in consideration for the development of safe and effective anti-Zika vaccines by precluding the possibility of adverse neurologic events including autoimmune diseases such as GBS.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

The accuracy of sales prediction models based on the big data of online word-of-mouth (eWOM) is still not satisfied. We argue that eWOM contains heat and sentiments of different product dimensions, which can improve the accuracy of these models. In this paper, we propose a dynamic topic analysis (DTA) framework in order to extract heat and sentiments of product dimensions from the big data of eWOM. Finally, we propose an autoregressive-heat-sentiment (ARHS) model, which integrates heat and sentiments of dimensions into the baseline predictive model. The empirical study in movie industry confirms that heat and sentiments of dimensions can improve the accuracy of sales prediction model. ARHS model is better for movie box-office revenue prediction than other models.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

The hygrothermal transfer is very important for the design of a building envelope for thermal comfort and economic and energy analysis of the building envelope. The applications of various materials in building envelope have been studied extensively. The study presents several models for the hygrothermal transfer for various building walls. Several energy and mass conservation equations with different boundary conditions and input considerations were presented in this paper for concrete, bricks and wooden walls. The effect of hysteresis was ignored in developing most model equations, while few considered flow pattern of fluid through the wall surfaces. Due to the flexibility of Luikov models, it formed the basis for modelling the coupled heat and mass transfer for porous material independent of hygroscopic nature with different boundary conditions defined according to the geometry and orientations. The influence of type of wall, orientation, thickness, the density of the material and climatic variations on the temperature and moisture evolutions within the building materials was more pronounced. Literature, presenting imaging models using imagery software like COMSOL multi-physics, CFD etc. were scarce considering that microscopic imagery is now deployed to measure the heat and moisture evolution in materials. Future models should include shrinkage or expansion influence on the fibrous material like wood due to their behaviour under environmental condition.

Recently, the demand for electric vehicle is increasing worldwide due to eco-friendly policies and stricter emission regulations. As a traction motor for electric vehicle, interior permanent magnet synchronous motors are mainly used. For the design of the interior permanent magnet synchronous motor, the magnetic equivalent circuit method, which is a method of lumped constant circuit, and the finite element method, which is a method of distributed constant circuit, mainly are used. Magnetic equivalent circuit method is useful for simple design through fast and intuitive parameters, but it cannot derive the distribution of magnetic field. The finite element method can derive an accurate magnetic field distribution, but it takes a long time to analyze and it is difficult to analyze intuitive design parameters. In this paper, magnetic equivalent circuit method and Carter coefficient are mixed for rotor structure design. This design method will be called the hybrid magnetic equivalent circuit method. Intuitive design parameters are derived through this hybrid magnetic equivalent circuit method. We will derive the Air gap flux density distribution according to rotor shape, no-load induced voltage, and cogging torque, and compare and verify it with the finite element method.

The objective of this study was to evaluate the effect of in ovo injection of L-arginine (L-Arg) into Ross broiler eggs at different embryonic developmental stages on their survival, hatchability, and body weight (BW). Additionally, we have analyzed the levels of serum glutamic-oxaloacetic transaminase (SGOT) and serum glutamic-pyruvic transaminase (SGPT), protein expression of heat shock proteins (HSPs), also we have the determined micronuclei (MN) and nuclear abnormality (NA). Results showed that survival and hatching rates as well as body weight were increased on the 14th day incubation compared to 8th and 18th day incubation at lower concentration of L-Arg. Moreover, the levels of SGOT and SGPT were also significantly (P < 0.05) increased at 14th day incubation at the same concentration (100μg/μl/egg) of injection. In addition, IgM levels were increased on the 14th day incubation compared to other days. The protein expressions of HSP-47, HSP-60, and HSP-70 in the liver were significantly down-regulated whereas the expression of myogenin and MyoD were significantly up-regulated on the 14th day after incubation in treated with all different doses such as 100μg, 1000μg and 2500μg/μl/egg namely 3T1, 3T2 and 3T3 respectively. However, the treatment with low dose of L-Arg down-regulated expression levels of those proteins on the 14th day incubation. Histopathology of liver by hematoxylin and eosin (H&E) straining showed that the majority of liver damage, specifically intracytoplasmic vacuoles, were observed in 3T1, 3T2, and 3T3. The minimum dose of 100 μg/ml/egg on the 14th day of incubation significantly prevented intracytoplasmic vacuole damages. These results demonstrate that in ovo administration of L-Arg at (100μg/μl/egg) may be an effective method to increase chick BW, hatch rate, increasing muscle growth related proteins and promote the immune response through increasing IgM on the 14th day of incubation period.

Present work has systematically investigated the evolution of dispersoid and elevated-temperature properties including the strength and creep resistance during the various multi-step heat treatments in Al-Mn-Mg 3004 alloys. Results show that only α-Al(MnFe)Si dispersoid is observed in the studied temperature range (up to 625°C) and it coarsens with increasing temperature to 500°C but dissolves at 625°C. The evolution of elevated-temperature strength and creep resistance is greatly related to the temperature of each step during the multi-step heat treatments. Generally, lower temperature at the first-step heat treatment leads to higher properties while the properties decrease with increasing temperature of last-step heat treatment. Suitable models have been introduced to explain the evolution of strength and the creep threshold stress at elevated-temperature during the various heat treatments.

In this study, we discuss the properties of absolute vacuum space and how these properties can play a vital role in creating a mechanism in which the very first particle gets created simultaneously everywhere and we find the limit in which when the absolute vacuum volume reaches will lead to the collapse that leads to the creation of the first particle. This discussion is made following to the elementary dimensions theory study that was peer-reviewed at the end of 2020, everything in the universe is made from four elementary dimensions, these dimensions are the three spatial dimensions (X, Y, and Z) and the Vacuum resistant as the factor of change among the four, time itself wasn’t considered as the fourth dimension, rather time corresponds to a factor of change, and during the research it was found out that the Vacuum resistant is the factor of change in the Absolute Vacuum space, where time is a hypothetical concept, that represents changes during certain events compared to a constant change rate event.Therefore, time does exist, but as a factor of change, and as the Vacuum resistant in the absolute vacuum space, Time= factor of change= Vacuum resistant. In the study, the internal and external vacuum resistant volume equivalent is found, External Vacuum resistant=3.2857602*10^15 *mass. This equation is used to identify the amount of Free external vacuum resistant created during nuclear fission and fusion: Initial mass of the excited nucleuses mass of the created new nucleuses+ 3.2857602*10^15 * the lost Mass. In elementary dimensions, the energy created during nuclear reactions is equivalent to the free External vacuum resistant created through nuclear reactions, and mass is equivalent to the internal Vacuum resistant.

Sumudu transform of the Dixon elliptic function with non zero modulus a ≠ 0 for arbitrary powers sm^N(x,a) ; N ≥ 1 ; sm^N(x,a)cm(x,a) ; N ≥ 0 and sm^N(x,a)cm²(x,a) ; N ≥ 0 is given by product of Quasi C fractions. Next by assuming denominators of Quasi C fraction to 1 and hence applying Heliermann correspondance relating formal power series (Maclaurin series of Dixon elliptic functions) and regular C fraction, Hankel determinants are calculated and showed by taking a = 0 gives the Hankel determinants of regular C fraction. The derived results were back tracked to the Laplace transform of sm(x,a) ; cm(x,a) and sm(x,a)cm(x,a).

The dynamic resistance is an important parameter in flux pumping. It is simple to calculate in slab geometry but more complex in tapes. In this paper another simple geometry is analysed which is a wire loop. To do this it is essential to make clear what is meant by the term 'voltage', which is ambiguous when there are alternating magnetic fields present. The term can be used if it refers to the EMF along a specified path. However this means that results are dependent on how the voltage leads are attached. If the n value of the V-I characteristic is large simple analytic expressions can be obtained. This will be referred to as the 'Bean' model solution. A more exact approach uses Faraday's law to derive a differential equation which is solved and compared with the Bean model. The dynamic resistance of the loop can be used to drive a flux pump of the type proposed by Geng and Coombs [4] and again simple expressions can be obtained for the performance. If the load is of high inductance L2 and the loop has an inductance L1 then the load current increases exponentially with a characteristic number of cycles L2/L1. The final current can be close to the critical value.

The move to a low carbon economy is very important for enhancing international competitiveness. The eco-innovation is the critical factor of the green paradigm. This study is designed to investigate deeply the determinants of eco-innovation of manufacturing firms in Korea by suggesting anticipated regulations, self-regulations, and industry-specific characteristics as external factors and open information sources as internal factors. The data used in the analysis is 1946 sample firms from Korean Innovation Survey 2010 based on the Oslo Manual. Using the multi-variate probit analysis and the zero-inflated negative binomial (ZINB) regression analysis, we have found out that the anticipated regulations and self-regulations have significant influences both on eco-process innovation and eco-product innovation, while industrial characteristics have no effects. The empirical results also show that the breadth of information sources has a positive effect on businesses in implementing eco-innovations. Our findings show that the Korean government should provide a good platform where firms can better understand the future trends of environmental policies, particularly policies on anticipated and self-regulations. At the same time, Korean firms should establish a voluntary system to control environmental activities so that they can improve eco-innovations through integrating external information.

Liquid metal alloy, incorporated with microfluidic manipulation, has become a promising candidate for flexible resistive sensor array (RSA) that can imitate the functions of human skin. One advantage of RSA with shared rows and shared columns is to reduce the number of wires from M × N to M + N (rows: M and columns: N) and hence to greatly lessen the complexity and burden on the electrical system. The associated drawback is the crosstalk effect between adjacent elements during measurement. Although many literatures have reported several methods to resolve this limitation, almost all of them focus only on the high resistance value (≥100 Ω) RSA. There is a lack of detailed experimental data that addresses low resistance RSA with sensing elements below 100 Ω. Here, we aim to fill the gap of this field. We established two common RSA readout systems, i.e. zero potential methods (ZPM) (setting non-scanned-sampling-electrode zero potential (S-NSSE-ZP) and setting non-scanned-sampling-electrode zero potential with amplifier (S-NSSE-ZP-A)) and to compare their performances in low resistance value (≤100 Ω) RSA. For ideal resistor RSA, the measurement results show that S-NSSE-ZP has at least one time higher error than S-NSSE-ZP-A.

The hybrid personal cooling system (HPCS) consisted of ventilation fans and phase change materials (PCMs) covered with insulation pads is a promising wearable cooling system to mitigate heat strain and heat-related illnesses of occupational workers with heavy labor in hot environments. Effects of clothing characteristics (e.g., thermal resistance of insulation pads, latent heat and melting temperature of PCMs) on the thermal performance of the HPCS have been investigated in detail in our previous study. Apart from the aforementioned factors, environmental conditions, i.e., environmental temperature and relative humidity, also significantly affect the thermal performance of the HPCS. In this paper, a numerical parametric study was performed to investigate the effects of the environmental temperature and relative humidity (RH) on the thermal management of the HPCS. Five levels of air temperature under environmental RH=50% were chosen (i.e., 32, 34, 36, 38 and 40 ºC) to study the impact of environmental temperature on the HPCS’s cooling performance. In addition, four levels of environmental RH at ambient temperatures of 36 and 40 ºC were selected (i.e., 30, 50, 70 and 90%) to examine the effect of RH on cooling performance of the HPCS. Results show that high environmental temperatures could accelerate the PCM melting process and thereby weaken the cooling performance of HPCS. In the moderately hot environment (36 °C), the HPCS presented good cooling performance with the maximum core temperature at around 37.5 °C during excise when the ambient RH≤70%, whereas good cooling performance could be only seen under RH≤50% in the extremely hot environment (40 °C). Thus, it may be concluded that the maximum environmental RH for the HPCS exhibiting good cooling performance decreases with the increase in the environmental temperature.

Traditional high pressure mechanical compressors account for over half of the car station’s cost, have insufficient reliability and are not feasible for a large-scale fuel cell market. An alternative technology, employing a two-stage, hybrid system based on electrochemical and metal hydride compression technologies, represents an excellent alternative to conventional compressors. The high-pressure stage, operating at 100-875 bar, is based on a metal hydride thermal system. A techno-economic analysis of the metal hydride system is presented and discussed. A model of the metal hydride system was developed, integrating a lumped parameter mass and energy balance model with an economic model. A novel metal hydride heat exchanger configuration is also presented, based on mini-channel heat transfer systems, allowing for effective high-pressure compression. Several metal hydrides were analyzed and screened, demonstrating that one selected material, namely (Ti_0.97Zr_0.03)_1.1Cr_1.6Mn_0.4, is likely the best candidate material to be employed for high-pressure compressors under the specific conditions. System efficiency and costs were assessed based on the properties of currently available materials at industrial levels. Results show that the system can reach pressures on the order of 875 bar with thermal power provided at approximately 150 °C. The system cost is comparable with the current mechanical compressors and can be reduced in several ways as discussed in the paper.

Cells form a bipolar spindle during mitosis to ensure accurate chromosome segregation. Proper spindle architecture is established by a set of kinesin motors and microtubule-associated proteins. In most eukaryotes, kinesin-5 motors are essential for this process, and genetic or chemical inhibition of their activity leads to the emergence of monopolar spindles and cell death. However, these deficiencies can be rescued by simultaneous inactivation of kinesin-14 motors, as they counteract kinesin-5. We conducted detailed genetic analyses in fission yeast to understand the mechanisms driving spindle assembly in the absence of kinesin-5. Here we show that deletion of the nrp1 gene, which encodes a putative RNA-binding protein with unknown function, can rescue temperature sensitivity caused by cut7-22, a fission yeast kinesin-5 mutant. Interestingly, kinesin-14/Klp2 levels on the spindles in the cut7 mutants were significantly reduced by the nrp1 deletion, although the total levels of Klp2 and the stability of spindle microtubules remained unaffected. Moreover, RNA-binding motifs of Nrp1 are essential for its cytoplasmic localization and function. We have also found that a portion of Nrp1 is spatially and functionally sequestered by chaperone-based protein aggregates upon mild heat stress and limits cell division at high temperatures. We propose that Nrp1 might be involved in post-transcriptional regulation through its RNA-binding ability to promote the loading of Klp2 on the spindle microtubules.

The work focused on the development of high-temperature electrical insulation coatings for film photovoltaics. The idea was into replacing the electroconductive metal dispersed phase in siloxane high-temperature coating to ceramic particles with phonon thermal conductivity. The slurry of industrial composition based on polysiloxane lacquer and thermally conductive paste containing zinc oxide was centrifuged to obtain a thin, optically transparent coating with the destruction temperature of over 600 °C. Topology, electrical properties, and thermal conductivity of the resulting film were investigated. The mathematical model of thermal processes in films in the course of heating was figured out. Quantitatively the relation of thermal conductivities of a control sample and a sample with a heat-conducting filler was established. The effectiveness of using this technology is shown.

Desalination accounts for 1% of the total global water consumption and is an energy-intensive process, with the majority of operational expenses attributed to energy consumption. Moreover, at present, a significant portion of the power comes from traditional fossil fuel-fired power plants and the greenhouse gas emissions associated with power production along with concentrated brine discharge from the process, pose a severe threat to the environment. Due to the dramatic impact of climate change, there is a major opportunity to develop sustainable desalination processes to combat the issues of brine discharge, greenhouse gas emissions along with a reduction in energy consumption per unit of freshwater produced. Nanotechnology can play a vital role to achieve specific energy consumption reduction as nanofluids application increases the overall heat transfer coefficient enabling the production of more water for the same size desalination plant. Furthermore, concentrated brine discharge harms the marine ecosystems, and hence, this problem must also be solved to support the objective of sustainable desalination. Several studies have been carried out in the past several years in the field of nanotechnology applications for desalination, brine treatment and the role of renewable energy in desalination. This paper aims to review the major advances in this field of nanotechnology for desalination. Furthermore, a hypothesis for developing an integrated solar thermal and nanofluid sustainable desalination system, based on the cyclic economy model is proposed.

Imatinib became the standard treatment for chronic myeloid leukemia (CML) about 20 years ago, which was a major breakthrough in stabilizing the pathology and improving the quality of life of patients. However, the emergence of resistance to imatinib and other tyrosine kinase inhibitors leads researchers to characterize new therapeutic targets. Several studies have highlighted the role of histone deacetylase 6 (HDAC6) in various pathologies, including cancer. This protein effectively intervenes in cellular activities by its primarily cytoplasmic localization. In this review, we will discuss the molecular characteristics of the HDAC6 protein, as well as its overexpression in CML leukemic stem cells, which make it a promising therapeutic target for the treatment of CML.

When considering implementation of shallow geothermal energy as a renewable source for heating and cooling of the building, special care should be taken in hydraulic design of borehole heat exchanger system. Laminar flow can occur in pipes due to usage of glycol mixture at low temperature or inadequate flow rate. This can lead to lower heat extraction and rejection rates of the exchanger because of higher thermal resistances. Furthermore, by increasing flow rate to achieve turbulent flow and satisfactory heat transfer rate can lead to increase the pressure drop of the system and oversizing of circulation pump which leads to impairment of seasonal coefficient of performance at the heat pump. Most frequently used borehole heat exchanger system in Europe is double-loop pipe system with smooth inner wall. Lately, development is focused on implementation of different configuration as well as with ribbed inner wall which ensures turbulent flow in the system, even at lower flow rates. At a location in Zagreb, classical and extended thermal response test was conducted on three different heat exchanger configurations in the same geological environment. With classic TRT test, thermogeological properties of the ground and thermal resistance of the borehole were determined for each smooth or turbulator pipe configuration. Extended Steady-State Thermal Response Step Test (TRST) was implemented, which incorporate series of power steps to determine borehole extraction rate at the define steady-state heat transfer conditions of 0/-3°C. Results show that heat exchangers with ribbed inner pipe wall have advantages over classic double-loop smooth pipe design, in terms of greater steady state heat extraction rate and more favorable hydraulic conditions.

Heat and power cogeneration plants based on fuel cells are interesting systems for energy- conversion at low environmental impact. Different fuel cells have been proposed, but experimental testing rigs are expensive and the development of commercial systems is time consuming if based on fully experimental activities. Furthermore, tight control of operation of fuel cells is compulsory to avoid damage, which must be based on accurate models, able to predict the cell behaviour and prevent stresses and shut-down. Some selected examples of steady state, dynamic and fluid dynamic modelling of different types of fuel cells are proposed, mainly PEMFC and SOFC type. The general ideas behind the thermodynamic, kinetic and transport description are recalled, with some examples of models derived for single cells, stacks and integrated power co-generation units.

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

The world is facing several global issues such as food and energy crisis, climate change and greenhouse gases emissions. To subdue these issues, many entities from academia and industries have innovated alternate techniques of performing regular activities which cause such problems. One of these innovations is the introduction of vertical and zero acreage farming in the field of sustainability. These carry the potential to solve one of the most important affairs of food security in most countries of the world. But, this technology has been in its nascent stage for many years. This paper uses a comprehensive framework proving the feasibility of initiating vertical farming on university campuses to feed the staff and students, which could also set an example to the rest of the world into using this technique on a wider scale. The study chose Huazhong University of science and technology (HUST) in Wuhan city, China for accessing the return on investment and food sufficiency if vertical farming is implemented. Using Central Limit Theorem, a statistical model was developed, and various scenarios were analyzed. The results indicated that if a separate vertical farm is constructed, the breakeven can be achieved in a range of 10-20 depending on parameters such as type of operation, number of floors and amount of vegetation. The study has shown that the use of vertical farming cannot only bring in revenue for the campus but also aid in mitigating climate change.

The energy efficiency of ice hockey arenas is a central concern for the administrations, as these buildings are well known to consume a large amount of energy. Since they are composite, complex systems, solutions to such a problem can be approached from many different areas, from managerial to technological to more strictly physical. In this paper we consider heat transfer processes in an ice hockey hall, during operating conditions, with a bottom-up approach based upon on-site measurements. Detailed heat flux, relative humidity and temperature data for the ice pad and the indoor air are used for a heat balance calculation in the steady-state regime, which quantifies the impact of each single heat source. We then solve the heat conduction equation for the ice pad in transient regime, and obtain a generic analytical formula for the temperature profile that can be used in practical applications. We then apply this formula to the resurfacing process for validation, and find good agreement with an analogous numerical solution. Since it is given with implicit initial condition and boundary conditions, it can be used not only in ice hockey halls, but in a large variety of engineering applications.

This work deals with a numerical implementation of a fifth order CENTRAL WENO-TVD (\textit{Weighted Essentially Non-Oscillatory-Total Variation Dimimishing}) of Haschem (2006) scheme applied to the convective terms of some hyperbolic conservation laws problems, in a volume finite framework. The WENO-TVD scheme is used to solve the 1D advection and Burgers equations. For this case is implemented two different numerical fluxes: The Lax-Friedrichs and TVD fluxes. In the TVD fluxes the schemes applied are in flux-limiter form. The schemes implemented for this flux are: Van Albada-1 (van Albada et al.,1982), van Albada-2 (Kermani et al., 2003), van Leer (Hassanzadeh, 2009) and MINMOD (Hirsch, 2007). The WENO type schemes are characterized for their high order approximation, and do not produce spurious oscilations near discontinuities, shocks and higher gradients. A third order Runge-Kutta TVD for the temporal variable is used. Qualitative and quantitative comparison are presented. The numerical solutions are computed with an in-house computer code developed in MATLAB software. In future works, it will develope a paralelization of computer code for solving systems of conservation laws, e.g. Euler equations of gas dynamics.

Chronic heat stress (HS), aggravated by global warming, reduces the production efficiency of the buffalo dairy industry. Here, we conducted a proteomic analysis to investigate the adaptation strategies used by buffalo in response to heat stress. Seventeen differentially abundant proteins with known functions were detected using label-free quantification (LFQ), and five of these differentially expressed proteins were validated with parallel reaction monitoring (PRM). These five proteins were associated with various aspects of heat stress, including decreased heat production, increased blood oxygen delivery, and enhanced natural disease resistance. Lipase (LPL), glutathione peroxidase 3 (GPX3), cathelicidin-2 (CATHL2, LL-37), ceruloplasmin (CP), and hemoglobin subunit alpha 1 (HBA1) were shown to play cooperative roles in the tolerance of chronic HS in dairy buffalo. We found that high levels of HBA1 increased blood oxygen transport capacity. Our results increase our understanding of the adaptation of dairy buffalo to chronic heat stress.

Over the last decade, there has been a growing interest in the use of a wide range of phytoadditives to counteract the harmful effects of heat stress in poultry. Willow (Salix spp.) is a tree with a long history. Among various forms, willow bark is an important natural source of salicin, β-O-glucoside of saligenin, but also of polyphenols (flavonoids and condensed tannins) with antioxidant, antimicrobial and anti-inflammatory activity. In light of this, the current review presents some literature data aiming to: (1) describe the relationship between heat stress and oxidative stress in broilers, (2) present or summarize literature data on the chemical composition of Salix species, (3) summarize the mechanisms of action of willow bark in heat-stressed broilers, (4) present different biological effects of the extract of Salix species in different experimental models.

In this study is developed an aerobic and anaerobic stoichiometric model for Saccharomyces cerevisiae, compartmentalized in mitochondria and cytosol. This model considers the central metabolism of S. cerevisiae and it possesses the peculiarity of having catabolic and anabolic biochemical reactions for the synthesis of the higher alcohols contained in tequila; involving 94 metabolites and 117 reactions; of which 93 correspond to biochemical internal reactions and 24 to transport fluxes between the medium and the cell. The model is validated under aerobic and anaerobic conditions for the main fermentation metabolites and it coincides with experimental results and those in silico reported in the literature. This model is used to obtain three different physiological states of S. cerevisiae through of estimation of its distributions of fluxes calculated from experimental data reported in literature of fermentation in continuous culture during the tequila production under different dilution rate (0.04-0.12 h^-1). The model developed constitutes a tool for the estimation of flux distribution maps during fermentation processes for the production of tequila, which could permit estimate yields and visualize different fermentation scenarios.

The color changes corresponding to chromophore structures in lignin caused by exposure of Eucalyptus（Eucalyptus grandis and E. urophylla）to heat were investigated. Eucalyptus wood samples were heated in saturated steam atmospheres for 10 h at 110℃, 130℃, and 150℃. The lignin was isolated before and after heat treatment. The physicochemical properties of the lignin and changes in chromophore structures during heat treatment was evaluated through wet chemical analysis, FTIR, UV-Vis, GPC, XPSand 13C-NMR. The color of the wood became darker and redder with the increase in pressure and temperature. Depolymerization and dehydration reactions occurred via demethoxylation with heat treatment in saturated steam at 110℃ or 130℃. Lignin condensed to form insoluble compounds after heat treatment in saturated steam at 150℃. G units increased and S units decreased through demethylation during heat treatment, as revealed by FTIR and 13C-NMR analysis.

Steel is one of the essential materials in the world's civilization. It is essential to produce many products such as pipelines, mechanical elements in machines, vehicles, profiles, and beam sections for buildings in many industries. Until the '50s of the 20th century, steel products required a complex process known as ingot casting; for years, steelmakers focused on developing and simplifying this process. The result was the con-tinuous casting process (CCP); it is the most productive method to produce steel. The CCP allows producing significant volumes of steel sections without interruption and is more productive than the formal ingot casting process. The CCP begins by transferring the liquid steel from the steel-ladle to a tundish. This tundish or vessel distributes the liquid steel, by flowing through its volume, to one or more strands having wa-ter-cooled copper molds. The mold is the primary cooling system, PCS, solidifying a steel shell to withstand a liquid core and its friction forces with the mold wall. Further down the mold, the rolls drive the steel section in the SCS. Here the steel section is cooled, solidifying the remaining liquid core, by sprays placed in every cooling segment all around the billet and along the curved section of the machine. Finally, the steel strand goes towards a horizontal-straight free-spray zone, losing heat by radiation mechanism, where the billet cools down further to total solidification. A moving torch cutting-scissor splits the billet to the desired length at the end of this heat-radiant zone.

Motivated by the well-known contradiction of special relativity and the heat equation, a wave equation for temperature scalar field is presented that also resolves the old controversy of (Lorentz) transformation of temperature and entropy. After showing that the current dogma of temperature and entropy being emergent concepts is based on but a logical fallacy, it is proposed that single particles posses entropy. This principle of fundamentality of entropy is then shown to be compatible with the equipartition theorem by yielding corrections in the quantum gravity regime.

This article investigates the features of heat and mass transfer for the steady two-dimensional Williamson nanofluid flow across an exponentially stretched surface depending on suction/injection. The boundary conditions incorporate the impacts of the Brownian motion and thermophoresis boundary. The analysis of heat transfer is carried out for the two cases of prescribed exponential order surface temperature (PEST) and prescribed exponential order heat flux (PEHF). The ongoing flow problem is mathematically modeled under the basic laws of motion and heat transfer. The similarity variables are allowed to transmute the governing equations of the problem into a similarity ordinary differential equation (ODEs). The solution of this reduced non-linear system of ODEs is supported by the Homotopy analysis method (HAM). The combination of HAM arrangements is acquired by plotting the h-curve. In order to evaluate the influence of several emergent parameters, the outcomes are presented numerically and are plotted diagrammatically as a consequence of velocity, temperature and concentration proles.

Long-term durability of the vacuum edge-seal plays a significant part in retrofitting triple vacuum glazing (TVG) to existing buildings in achieving towards zero-energy buildings (ZEB) target. Vacuum pressure decrement with respect to time between panes affect the thermal efficiency of TVG. This study reports a 3D finite element model, with validated mathematical methods and comparison, for the assessment of the influence of vacuum pressure diminution on the thermal transmittance (U value) of TVG. The centre-of-pane and total U values of TVG calculated to be 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ at the cavity vacuum pressure of 0.001 Pa. The results suggests that a rise in cavity pressure from 0.001 Pa to 100 kPa increases the centre-of-pane and total U values from 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ to 2.4 Wm⁻²K⁻¹ and 2.58 Wm⁻²K⁻¹, respectively. The temperature descent on the surfaces of TVG between hot and cold sides’ increases by decreasing the cavity vacuum pressure from 50 kPa to 0.001 Pa. To maintain the cavity vacuum pressure of 0.001 Pa for over 20 years of life span in the cavity of 10 mm wide edge sealed triple vacuum glazing, non-evaporable getters will maintain the cavity vacuum pressure that will enable the long-term durability to TVG.

Considering increasingly ambitious pledges by countries, pressure from society, investors, and clients further up the supply chain, the question for companies is not so much whether to take decarbonisation action, but what action and by when. However, determining an ideal mix of measures to apply ‘decarbonisation efficiency’ requires more than knowledge of technically feasible measures and how to combine them to achieve the most economic outcome: In this paper, the author describes seven aspects which heavily influence the composition of an ‘ideal mix’ that executive leadership needs to take a (strategic) position on. These aspects consider underlying motivations and span across (socio-)economic, technical, regulatory, strategic, corporate culture and environmental factors and further underline the necessity of clarity of definitions. How these decisions influence the determination of the decarbonisation-efficient ideal mix of measures, both in principle but also in terms of specific impact is further explored by providing examples. What choices are taken by German manufacturers in several of the aspects is disclosed by insights from about 850 responses to the ‘Energy Efficiency Index of German Industry’. Knowledge of the status quo, and clarity in definitions, objectives, time frames and scope are key.

The circuitry of the summarized "floating" differential stages (FDS) based on complementary field-effect transistors with a control p-n junction (CJFET), intended for use in low-noise analog microcircuits, for example, operational amplifiers. The results of modeling the flow characteristics of one of the CJFET FDSs in the LTSpice XVII environment at low temperatures (down to -197 ⁰С) and exposure to a neutron flux in the range of 1e13 ÷ 1e15 n / cm² are presented.

High concentrations of Na⁺ or [Co(NH₃)₆]³⁺ can induce the B to Z conformational transition in alternating (dC-dG) oligo and polynucleotides. The use of short DNA oligomers (dC-dG)₄ and (dm⁵C-dG)₄ as models can allow a thermodynamic characterization of the transition. Both form right handed double helical structures (B-DNA) in standard phosphate buffer with 115 mM Na⁺ at 25 ^oC. However, at 2.0 M Na⁺ or 200 mM [Co(NH₃)₆]³⁺, (dm⁵C-dG)₄ assumes a left handed double helical structure (Z-DNA) while the unmethylated (dC-dG)₄ analogue remains right handed under those conditions. We have previously demonstrated that the enthalpy of the transition at 25 ^oC for either inducer can be determined using isothermal titration calorimetry (ITC) [Ferreira, J. M. & Sheardy, R. D., Biophys. J. 2006, 91, 1–7]. Here, ITC is used to investigate the linkages between temperature, water activity and DNA conformation. We found that the determined enthalpy for each titration varied linearly with temperature allowing determination of the heat capacity change (DC_p) between the initial and final states. As expected, the DC_p values were dependent upon the cation (i.e. Na⁺ vs [Co(NH₃)₆]³⁺) as well as the sequence of the DNA oligomer (i. e., methylated vs unmethylated). Osmotic stress experiments were carried out to determine the gain or loss of water by the oligomer induced by the titration. The results are discussed in terms of solvent accessible surface areas, electrostatic interactions and the role of water.

As an essential synthetic material used in continuous casting of steels, mold fluxes improve the surface quality of steel slabs. In this study, a CaO-SiO₂-Na₂O based low-fluorine mold flux was solidified by an improved water-cooled copper probe with different temperatures of molten flux and different probe immersion times. The heat flux through solid films and the film structures were calculated and inspected, respectively. The results indicate: large internal cracks (formed in the glassy layer of films during solidification) were observed, the formation and evolution of those cracks contributed to the the unstable heat flux density. The roughness of the surface in contacted with the water-cooled copper probe formed as films were still glassy and the roughness have no causal relationship with crystallization or devitrification. Combeite with columnar and faceted dendritic shapes is the main crystal in the film.

Space shuttle has been a hall mark of American space program since its inception. Despite its temporary shutdown few years ago, with the recent interest in space exploration which includes revitalizing human outpost in microgravity and transportation required to build it, realize other experiments (e.g. in space telescopes, in space manufacturing) and interplanetary voyages, it has regained attention. Its superior design, manufacturing, materials, performance, durability, and efficiency place it among the best, in fact, the only effort by mankind to build a reusable craft horizontally, launch vertically like a rocket and fly back like a plane. Various requirements emerge during its design (thermal, fluid, acoustics, vibration and structural) and design of its main engine (Aerojet Rocketdyne RS 25) which requires considerable attention, heat transfer being most important. This facilitated and necessitated use of various types of heat exchangers such as single coil, heat pipe, built in internal heat exchanger (IHEX), external heat exchanger (EHEX), condensing heat exchanger (CHEX), Interface heat exchangers (InHEX), regenerative heat exchanger (RHEX) and compact heat exchangers (CoHEX), change, manipulate and optimize their configurations in piping and instrumentation diagrams (PIDs). In this short narrative, an effort has been made to summarize them, and their developments over time with a focus on the application, design, manufacturing, materials, and performance (in service and final operation).

The one-to-one structural correspondence between any conjugated hydrocarbon CnHm and the borane BnHm+n is extended here, with the B3LYP/cc-pVDZ model, to pure conjugated carbon systems with the example of buckminsterfullerene C60 with the corresponding icosahedral isoelectronic system closo-borane B60H60, and the fluorine substituted systems B60F30H30 and B60F60 , all with icosahedral Ih symmetry. All systems correspond to energy minima in the potential energy hypersurface, except for B60(F30)in(H30)out . Selected electronic structure methods are used to characterize all systems: molecular electrostatic potentials (MEP), atomic charges, bond orders, and topological properties of the electron density within quantum theory of atoms-in-molecules (QTAIM) and electron-localization function (ELF) theory. In the particular case of B60H60 we use the recently developed Hückeloid model to characterize this system. The stability of the energy minimum icosahedral structure B60F60 could have an origin in F···F attractive interactions of the inner fluorine atoms of the cage.

ASTM A743 CA6NM alloy is a martensitic stainless steel typically used in energy industry -runners and hydraulic turbine components- due to its superior toughness, yield and fatigue properties. In both the manufacturing, shielded metal arc welding is applied to join for this grade steels. However, weldability of the steels is limited due to formation of hard and brittle phases such as untempered martensite during welding and post weld heat treatment processes. The formation causes a reduction in toughness. In this study, influence of post-weld heat treatment procedure (single tempering and double tempering) and parameters on microstructure and hardness of AWS410NiMo all weld metal. Hardness tests were conducted from weld metal. Microstructures of the all weld metals subjected to different heat treatment process were characterized.

Building roofs are sources of unwanted heat for buildings situated in zones with a warm climate. Thus, reflective coatings have emerged as an alternative to reject a significant fraction of solar energy received by roofs. In this research, the thermal behavior of concrete slab-type roofs with traditional and solar reflective coatings was simulated using a computational tool. Weather data from four cities in Mexico with a warm climate were used as boundary conditions. This tool is an in-house code based on the Finite Volume Method developed by the author to perform building components simulations. The code was validated with experimental data from previous work. A series of comparative simulations were developed, taking a gray roof as a control case. The results showed that for the roof without thermal insulation (single roof), the solar reflective coatings reduced the exterior surface between 11 and 16∘C. Consequently, the single roofs’ daily heat gain was reduced by a factor ranging between 41 and 54%. On the other hand, for the insulated roof, the reflective coatings reduced the exterior surface temperature between 17 and 21∘C. At the same time, the daily heat gain of composite roofs was reduced between 37 and 56%.

A universally applicable method for the prediction of the isobaric heat capacities of the liquid and solid phase of molecules at 298.15 K is presented, derived from their “true” volume. The molecules’ “true” volume in A³ is calculated on the basis of their geometry-optimized structure and the Van-der-Waals radii of their constituting atoms by means of a fast numerical algorithm. Good linear correlations of the “true” volume of a large number of compounds encompassing all classes and sizes with their experimental liquid and solid heat capacities over a large range have been found, although noticeably distorted by intermolecular hydrogen-bond effects. To take account of these effects, the total amount of 1303 compounds with known experimental liquid heat capacities has been subdivided into three subsets consisting of 1102 hydroxy-group-free compounds, 164 monoalcohols/monoacids, and 36 polyalcohols/polyacids. The standard deviations for Cp(liq,298) were 20.7 J/mol/K for the OH-free compunds, 22.91 J/mol/K for the monoalcohols/monoacids and 16.03 J/mol/K for the polyols/polyacids. Analogously, 797 compounds with known solid heat capacities have been separated into a subset of 555 OH-free compounds, 123 monoalcohols/monoacids and 119 polyols/polyacids. The standard deviations for Cp(sol,298) were calculated to 23.14 J/mol/K for the first, 21.62 J/mol/K for the second, and 19.75 J/mol/K for the last subset. A discussion of structural and intermolecular effects influencing the heat capacities as well as of some special classes, in particular hydrocarbons, ionic liquids, siloxanes and metallocenes, has been given. In addition, the present method has successfully been extended to enable the prediction of the temperature dependence of the solid and liquid heat capacities in the range between 250 and 350 K.

This brief commentary challenges the use of the term "energy deficiency" in nutrition and metabolism, providing a critical examination of its scientific and philosophical aspects. It emphasizes the need to consider rare diseases associated with actual energy deficiency, which extend beyond the scope of everyday tiredness or fatigue. By analyzing energy balance and its complexities, this critique underscores the oversimplification associated with the term and its potential for misleading implications. It highlights the dynamic nature of energy metabolism and the intricate mechanisms involved in maintaining energy equilibrium, including the impact of rare genetic and physiological abnormalities. In addition to the discussion on energy balance, this commentary explores the manifestation of rare diseases that disrupt energy production, utilization, or hormonal regulation. Conditions such as mitochondrial diseases, glycogen storage diseases, adrenal insufficiency, and Prader-Willi syndrome are examined, shedding light on their profound impact on individuals' energy levels and overall health. The distinct time courses, underlying mechanisms, and clinical implications of protein deficiency, energy deficiency, and vitamin C deficiency are also compared, further emphasizing the complexity of energy metabolism and its relationship with various nutrient deficiencies. To foster a more comprehensive understanding of energy metabolism and enhance clarity in communication within the field, the commentary proposes the adoption of alternative terminology, such as "energy flux," to capture the multifaceted nature of energy balance more accurately. By reevaluating the terminology employed, researchers and healthcare professionals can better convey the intricate dynamics of energy metabolism and address the unique challenges faced by individuals with rare diseases causing actual energy deficiency. In conclusion, this commentary serves as a thought-provoking exploration of the concept of energy deficiency in nutrition and metabolism. It highlights the limitations of the term in capturing the complexities of energy balance, particularly in the context of rare diseases. By broadening the discussion to include these rare conditions, it encourages a more comprehensive understanding of energy metabolism and calls for precise and nuanced terminology to facilitate effective communication and advancements in the field.

In 2010, Parties to the Convention on Biological Diversity (CBD) adopted the Strategic Plan for Biodiversity 2011–2020 to address the loss and degradation of nature. Subsequently, most biodiversity indicators continued to decline. Nevertheless, conservation actions can make a positive difference for biodiversity. The emerging Post-2020 Global Biodiversity Framework has potential to catalyze efforts to ‘bend the curve’ of biodiversity loss. Thus, the inclusion of a goal on species, articulated as Goal B in the Zero Draft of the Post-2020 Framework, is essential. However, as currently formulated, this goal is inadequate for preventing extinctions, and reversing population declines; both of which are required to achieve the CBD’s 2030 mission. We contend it is unacceptable that Goal B could be met while most threatened species deteriorated in status and many avoidable species extinctions occurred. We examine the limitations of the current wording and propose an articulation with robust scientific basis. A goal for species that strives to end extinctions and recover populations of all species that have experienced population declines, and especially those at risk of extinction, would help to align actors towards the transformative actions and interventions needed for humans to live in harmony with nature.

Lignin has interesting functionalities to be exploited in adhesives for medicine, foods and textiles. Nanoparticles (NPs) <100 nm coated with poly(L-lysine), PL and poly(L-glutamic acid) PGA were prepared from the laccase treated lignin to coat nanocellulose fibrils (CNF) with heat. NPs ca. 300 nm were prepared, β-casein coated and cross-linked with transglutaminase (Tgase) to agglutinate chamois specimens. Size exclusion chromatography (SEC) and Fourier-transform infrared (FTIR) spectroscopy were used to characterize polymerized lignin, zetapotential and dynamic light scattering (DLS) to ensure coating of colloidal lignin particles (CLPs). Protein adsorption on lignin was studied by quartz crystal microbalance (QCM). Atomic force microscopy (AFM) was exploited to examine interactions between different polymers and to image NPs with transmission electron microscopy (TEM). Tensile testing showed, when using CLPs for the adhesion, the stress improved ca. 10 and strain ca. 6 times compared to polymeric lignin. For the β-casein NPs the values were 20 and 8, respectively, and for the β-casein coated CLPs between these two cases. When NPs were dispersed in adhesive formulation, the Young's moduli confirmed significant improvement in the elasticity of the joints over the adhesive alone. Exploitation lignin in nanoparticulate morphology is a potential method to prepare bionanomaterials for advanced applications.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

Vaccination against Newcastle disease (ND), a devastating viral disease of chicken, is often hampered by thermal inactivation of the live vaccines, in particular in tropical and hot climate conditions. In the past “thermostable” vaccine strains (I-2) have been proposed to overcome this problem. In the current study, we compared the thermal stability of 6 commercially available ND vaccines. Subjected to 37°C as lyophilized preparation, two vaccines containing I-2 strains were more sensitive to inactivation than a third I-2 vaccine or when compared to three other vaccines based on different strains. However, after reconstitution strains proved to have a comparable tenacity. Interestingly, all vaccines retained a sufficient virus dose for protection (106 EID50) after 1 day at 37°C, still. However, experiments exposing ND-vaccines to elevated temperatures of 51°C and 61°C, clearly demonstrated inactivation of all dissolved vaccines within 2 to 4 hours. The data indicate preparation that specific factors may influence thermal stability rather than strain specific characteristics. Regardless of the ND strain used, the appropriate cold chain is mandatory for live ND-vaccines.

The aim of this articles is to investigate the entropy optimization in unsteady MHD flow Darcy-Forchheimer nanofluids towards a stretchable sheet. The surface we tend to think about is porous and stretchy under acceleration. Flow occurs due to the stretching of the surface. Four distinct types of aqueous nanostructures are taken in this examination where copper oxide ( ), copper ( ), titanium dioxide ( ) and aluminum oxide ( ) are the nanoparticles. Irreversibility analysis are discussed through second law of thermodynamics. The expression of energy is mathematically designed and discussed according to heat generation / absorption, dissipation, thermal radiation, and joule heating. The nonlinear PDE (partial differential conditions) is first changed to ODE (normal differential conditions) through appropriate similarity variables. Here we used the numerically embedded solution technique to develop a numerical result for the obtained nonlinear flow expression. Influence of various flow parameter velocity temperature distribution and entropy generation are discussed. Reduction occurs in velocity profile for larger porosity and magnetic parameters. An enhancement in entropy generation and temperature distribution is seen for Brinkman number. An opposite effect is noticed in velocity and temperature through solid volume friction.