Low-temperature processed ITO thin films offer the potential of overcoming the doping limit by suppressing the equilibrium of compensating oxygen interstitial defects. To elucidate this potential, electrical properties of Sn-doped In₂O₃ (ITO) thin films are studied in dependence on film thickness. In-operando conductivity and Hall effect measurements during annealing of room temperature deposited films with different film thickness in different environments allow to discriminate between the effects of crystallization, grain growth, donor activation and oxygen diffusion on carrier concentrations and mobilities. At 200 °C, a control of carrier concentration by oxygen incorporation or extraction is only possible for very thin films. The electrical properties of thicker films deposited at room temperature are mostly affected by grain size. The remaining diffusivity of compensating oxygen defects at 200 °C is sufficient to screen the high Fermi level induced by deposition of Al₂O₃ using atomic layer deposition (ALD), which disables the use of defect modulation doping at this temperature. The results indicate that achieving higher carrier concentrations requires a control of the oxygen pressure during deposition in combination with seed layers to enhance crystallinity or the use of near room temperature ALD.

Leaf temperature (T_leaf) influences photosynthesis and respiration. Currently, there is a growing interest on including lianas in productivity models due to their increasing abundance, and their detrimental effects on net primary productivity in tropical environments. Therefore, understanding the differences of T_leaf between lianas and trees is important for future of forest on whole ecosystem productivity. Here we determined the displayed leaf temperature (T_d= T_leaf – ambient temperature) of several species of lianas and their host trees during ENSO and non-ENSO years to evaluate if the presence of lianas affects the T_d of their host trees, and if leaves of lianas and their host trees exhibit differences in T_d. Our results suggest that close to midday, the presence of lianas does not affect the T_d of their host trees; however, lianas tend to have higher values of T_d than their hosts across seasons, in both ENSO and non-ENSO years. Although lianas and trees tend to have similar physiological-temperature responses, differences in T_d could lead to significant differences in rates of photosynthesis and respiration based temperature response curves. Future models should thus consider differences in leaf temperature between these life forms to achieve robust predictions of productivity.

This study evaluates the historical mean surface temperature (hereafter T2m) and examines how T2m changes over East Africa (EA) in the 21^st century using CMIP6 models. An evaluation was conducted based on mean state, trends, and statistical metrics (Bias, Correlation Coefficient, Root Mean Square Difference, and Taylor skill score). For future projections over EA, five best performing CMIP6 models (based on their performance ranking in historical mean temperature simulations) under the shared socioeconomic pathways SSP2-4.5 and SSP5-8.5 scenarios were employed. The historical simulations reveal an overestimation of the mean annual T2m cycle over the study region with fewer models depicting underestimations. Further, CMIP6 models reproduce the spatial and temporal trends within the observed range proximity. Overall, the best performing models are as follows: FGOALS-g3, HadGEM-GC31-LL, MPI-ESM2-LR, CNRM-CM6-1, and IPSL-CM6A-LR. During the three-time slice under consideration, the Multi Model Ensemble (MME) project many changes during the late period (2080 – 2100) with expected mean changes at 2.4 °C for SSP2-4.5 and 4.4 °C for the SSP5-8.5 scenario. The magnitude of change based on Sen’s slope estimator and Mann-Kendall test reveal significant increasing tendencies with projections of 0.24°C decade-1 (0.65°C decade-1) under SSP2-4.5 (SSP5-8.5) scenarios. The findings from this study illustrate higher warming in the latest model outputs of CMIP6 relative to its predecessor, despite identical instantaneous radiative forcing.

With the diversified development of media forms, livestreaming e-commerce has become a new sales model. Unlike the traditional sales model, this paper constructs a three-party game model composed of manufacturers, social media influencers and consumers based on the livestreaming model. It explores the equilibrium strategy selections of each participant in the supply chain system. In analyzing the evolutionary game stability of each participant, this paper obtains the equilibrium strategy and stability factors by analysis of the income and expenditure matrix. It uses the simulation model to analyze reasons for strategy selections of different game participants in the livestreaming e-commerce model. The results show that the strategies of manufacturers, social media influencers and consumers' selections have different impacts on their decision-making mechanism, and man-ufacturers are more sensitive to consumers' active participation in livestreaming e-commerce.

Linear state estimation (SE) formulation under a rectangular coordinate system has been proved to be applicable for real-time distribution network management. Micro phasor measurements’ model can be accommodated into this kind of SE easily. However, voltage magnitude, active power and reactive power measurements are transformed to linear measurements with large node voltage error. To cope with this issue, a linear state estimation under a polar coordinate system is adopted at the first stage to obtain accurate enough complex node voltage, and then nonlinear measurements are transformed to be linear with complex node voltage. At the second stage, linear SE under a rectangular coordinate system can be adopted to satisfy more strict network constraints. The proposed two-stage linear SE is validated on balanced 14, 33, 70,84, 119, 135 nodes network and IEEE 13, 34, 37,123 unbalanced test feeders.

A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

Phosphors based on magnesium titanate activated with Mn⁴⁺ ions are of great interest because, when excited with blue light, they display a strong red-emitting luminescence. They are characterized by a luminescence decay which is strongly temperature dependent in the range from 0 to 80 °C, making these materials very promising for temperature sensing in the biochemical field. In this work the optical and thermal properties of the luminescence of Mg₂TiO₄ are investigated for different Mn⁴⁺ doping concentrations. The potential of this material for temperature sensing is demonstrated by fabricating a fiber optic temperature microsensor and by comparing its performance against a standard resistance thermometer. The response of the fiber optic sensor is exceptionally fast, enabling monitoring of temperature fluctuation in subsecond time domain.

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1,000, the Cerberus – an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200^oC-capable heated bed, ii) 500^oC-capabel hot end, iii) isolated heated chamber with 1kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5 MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization.

Mushrooms have long rich history in folk medicine, traditional and functional foods due to high content of dietary myco-nutrients. Currently, there is increased interest in finding appropriate food-grade green ex-traction systems capable of extracting these bioactive compounds from dietary mushrooms for applica-tions in various food, pharmacological or nutraceutical formulations. Herein, we evaluated a modified Swiss water process (SWP) method using alkaline and acidic pH at low and high temperature under pressurized conditions as a suitable green food grade solvent to obtained extracts enriched with my-co-nutrients (dietary phenolics, total antioxidants (TAA), vitamins, and minerals) from Chaga. Ultra-high performance liquid chromatography coupled to high resolution accurate mass tandem mass spectrometry (UHPLC-HRAMS-MS/MS) was used to assess the phenolic compounds and vitamin levels in the extracts, while inductively coupled plasma mass spectrometry (ICP-MS) was used to determine the mineral con-tents. Over twenty phenolic compounds were quantitatively evaluated in the extracts and the highest total phenolic content and antioxidant activity was observed at pH11.5 at 100°C. The most abundant phenolic compounds present in Chaga extracts included phenolic acids such as protocatechuic acid 4-glucoside (0.7-1.08µg/mL), syringic acid (0.62-1.18µg/mL), and myricetin (0.68-1.3µg/mL). Vitamins are being reported for the first time in Chaga. pH 2.5 at 100°C treatment shows superior effects in extracting the B vitamins whereas pH 2.5 at 60 and 100°C treatments were outstanding for extraction of total fat-soluble vitamins. Vitamin E content was the highest for the fat-soluble vitamins in the Chaga extract under acidic pH (2.5) and high temp. (100°C) and ranges between 50 to 175 µg/100g Chaga. Antioxidant minerals ranged from 85.94 µg/g (pH7 at 100°C) to 113.86 µg/g DW (pH2.5 at 100°C). High temperature 100°C and a pH of 2.5 or 9.5. The treatment of pH11.5 at 100°C was the most useful for recovering phenolics and antioxidants from Chaga including several phenolic compounds reported for the first time in Chaga. SWP is being proposed herein for the first time as a novel, green food-grade solvent system for the extraction of myco-nutrients from Chaga and have potential applications as a suitable approach to extract nutrients from other matrices. Chaga extracts enriched with bioactive myconutrients and antioxidants may be suitable for further use or applications in the food and nutraceutical industries.

Intermetallic alloys like e.g. Iron-Aluminides, Titanium-Aluminides or Molybdenum- Silizides are prospective materials for high-temperature applications. For additive manufacturing (AM) intermetallic structural materials are particularly challenging due to their high melting points, oxygen susceptibility and low temperature brittleness. The feasibility of manufacturing intermetallic Mo-Si-B alloys with the laser additive manufacturing process of direct energy deposition (DED) is demonstrated and recent results in characterizing rapidly solidified material with respect to correlations between process, composition and microstructures are presented. The possibility to dope the material with Yttrium oxide (Y2O3) for dispersion is successfully demonstrated. Current challenges, e.g. homogenous distribution of alloying elements and applicability are addressed.

We replace the current industry-standard empirical forecasts of oil production from hydrofractured horizontal wells in shales with a statistically and physically robust, accurate and precise approach, using the Bakken shale as an illustration. The proposed oil production forecasting method extends our previous work on predicting fieldwide gas production in the Barnett shale and merges it with our new scaling of oil production in shales. We first divide the existing 14,678 horizontal oil wells in the Bakken into 12 static samples in which depositional settings and completion technologies are similar. For each sample, we construct a purely data-driven P50 well prototype by merging the GEV distribution fits of oil production from appropriate well cohorts. We fit the parameters of our physics-based scaling curve to the statistical well prototypes, and obtain their smooth extrapolations to 30 years on production. By calculating the number of potential wells of each Bakken region, and scheduling future drilling programs, we stack up the extended well prototypes to achieve the most plausible forecast. We predict that Bakken will ultimately produce 5 billion barrels of oil from the existing wells, with the possible increments of 2 and 6 billion barrels from core and noncore areas.

Hydrogen used as an energy carrier can provide an important route to the decarbonization of energy supplies. However, realizing this opportunity requires a significant increase in both production and transportation capacity. Part of the increase in transportation capacity could be provided by the shipping of liquid hydrogen, but this introduces an energy-intensive liquefaction step into the supply-chain. The energy required for liquefaction can be reduced by developing improved process designs, but since all low-temperature processes are affected by the available heat-sink temperature, local ambient conditions will also affect the energy penalty. This work studies how the energy consumption associated with liquefaction varies with heat-sink temperature through the optimization of design parameters for a typical next-generation hydrogen liquefaction process. The results show that energy consumption increases by around 20%, across the cooling temperature range 5 to 50 °C. Considering just the range 20 to 30 °C there is a 5% increase, illustrating the significant impact ambient temperature can have on energy consumption.

Object. Utilization of pedicle screws (PS) for spine stabilization is common in spinal surgery. With reliance on visual inspection of anatomical landmarks prior to screw placement, the free-hand technique requires a high level of surgeon skill and precision. Three-dimensional (3D) computer-assisted virtual neuronavigation improves the precision of PS placement and minimize steps. Methods. Twenty-three patients with degenerative, traumatic, or neoplastic pathologies received treatment via a novel three-step PS technique that utilizes a navigated power driver in combination with virtual screw technology. 1) Following visualization of neuroanatomy using intraoperative CT, a navigated 3-mm match stick drill bit was inserted at anatomical entry point with screen projection showing virtual screw. 2) Navigated Stryker Cordless Driver with appropriate tap was used to access vertebral body through pedicle with screen projection again showing virtual screw. 3) Navigated Stryker Cordless Driver with actual screw was used with screen projection showing the same virtual screw. One hundred and forty-four consecutive screws were inserted using this three-step, navigated driver, virtual screw technique. Results. Only 1 screw needed intraoperative revision after insertion using the three-step, navigated driver, virtual PS technique. This amounts to a 0.69% revision rate. One hundred percent of patients had intraoperative CT reconstructed images to confirm hardware placement. Conclusions. Pedicle screw placement utilizing the Stryker-Ziehm neuronavigation virtual screw technology with a three step, navigated power drill technique is safe and effective.

This work presents the computation of reliable warming trends for central Australia around Alice Springs within a circle of radius 1,000 km. Between 1880 and 2011, the average warming for the centre of Australia is +0.166 ºC/century, slightly smaller than the warming of Alice Springs, that is +0.176 ºC/century. Over a shorter time between 1910 and 2011, the centre of Australia is warming +0.794 ºC/century, slightly more than the warming of Alice Springs, that is +0.719 ºC/century.

Global population is predicted to approach 10 billion by 2050, an increase of over 2 billion from today. To meet the demands of growing, geographically and socio-economically diversified nations, we need to diversity and expand agricultural production. This expansion of agricultural productivity will need to occur under increasing biotic, and environmental constraints driven by climate change. Clustered regularly interspaced short palindromic repeats-site directed nucleases (CRISPR-SDN) and similar genome editing technologies will likely be key enablers to meet future agricultural needs. While the application of CRISPR-Cas9 mediated genome editing has led the way, the use of CRISPR-Cas12a is also increasing significantly for genome engineering of plants. The popularity of the CRISPR-Cas12a, the type V (class-II) system, is gaining momentum because of its versatility and simplified features. These include the use of a small guide RNA devoid of trans-activating crispr RNA (tracrRNA), targeting of T-rich regions of the genome where Cas9 is not suitable for use, RNA processing capability facilitating simpler multiplexing, and its ability to generate double strand breaks (DSB) with staggered ends. Many monocot and dicot species have been successfully edited using this Cas12a system and further research is ongoing to improve its efficiency in plants, including improving the temperature stability of the Cas12a enzyme, identifying new variants of Cas12a or synthetically producing Cas12a with flexible PAM sequences. In this review we provide a comparative survey of CRISPR-Cas12a and Cas9, and provide a perspective on applications of CRISPR-Cas12 in agriculture.

We present a distributed optical-fiber temperature sensor with enhanced sensitivity based on an Al-coated fiber using the Rayleigh backscattering spectra (RBS) shift in optical frequency-domain reflectometry (OFDR). The Al-coated sensing fiber with a higher thermal expansion coefficient compared to silica produces a strain-coupled shift in the RBS under an increase in temperature. This effect leads to an enhanced temperature sensitivity of the distributed measurement scheme. Our results revealed that the temperature sensitivity obtained using the Al-coated fiber in OFDR was ~56% higher relative to that of a single-mode fiber. Moreover, the minimum measurable temperature recorded was 1 °C with a spatial resolution of 5 cm.

Selective laser melting (SLM) is one of the widely used techniques in metallic additive manufacturing, in which high-density laser powder is utilized to selectively melting layers of powders to create geometrically complex parts. Temperature distribution and molten pool geometry directly determine the balling effect, and concentrated balling phenomenon significantly deteriorates surface integrity and mechanical properties of the part. Finite element models have been developed to predict temperature distribution and molten pool geometry, but they were computationally expensive. In this paper, the three-dimensional temperature distributions are predicted by analytical models using point moving heat source and semi-ellipsoidal moving source respectively. The molten pool dimensions under various process conditions are obtained from the three-dimensional temperature predictions and experimentally validated. Ti-6Al-4V alloy is chosen for the investigation. Good agreements between the predictions and the measurements are observed. The presented models are also suitable for other metallic materials in the SLM process.

Temperature field is an essential attribute of metal additive manufacturing in view of its bearings on the prediction, control, and optimization of residual stress, part distortion, fatigue, balling effect, etc. This work provides an analytical physics-based approach to investigate the effect of scan strategy parameters including time delay between two irradiations and hatching space on thermal material properties and melt pool geometry. This approach is performed through the analysis of the distribution of material properties and temperature profile in three-dimensional space. The moving point heat source approach is used to predict the temperature field. To predict the temperature field during the additive manufacturing process some important phenomena are considered. 1) Due to the high magnitude of temperature in the presence of the laser, the temperature gradient is usually high which has a crucial influence on thermal material properties. Consequently, the thermal material properties of stainless steel grade 316L are considered to be temperature-dependent. 2) Due to the repeated heating and cooling, part usually undergoes several melting and solidification cycles. This physical phenomenon is considered by modifying the heat capacity using the latent heat of melting. 3) The multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the successive layers has an impact on heat transfer mechanisms. 4) Effect of heat affected zone on thermal material properties is considered by the superposition of material properties in regions where the temperature fields of two consecutive irradiations have an overlap since the consecutive irradiations change the behavior of the material properties. The goals are to 1) investigate the effects of temperature-sensitive material properties and constant material properties on the temperature field. 2) Study the behavior of thermal material properties under different scan strategies. 3) Study the importance of considering the effect of heat affected zone on thermal material through the prediction of melt pool geometry. 4) Investigate the effect of hatching space on melt pool geometry. This work is purely employed physics-based analytical models to predict the behavior of material properties and temperature field under different process conditions, and no finite element modeling is used.

This paper explores the effect of climate change on the regression of the Argan tree (Argania spinosa L. Skeels) woodland, focusing on the Argan Biosphere Reserve and especially in the Souss plain (Western Morocco). Rainfall and temperature data of four sites within the Argan Biosphere Reserve were analyzed over the last 60 years to assess any climatic change. Regression curves applied to the dataset showed an important decrease in rainfall (18 to 26 %) in the four locations as well as an increase in temperature (1 to 2 °C). These changes may have a detrimental effect on the Argan woodland although human factors have been reported to be the main factor of its regression. It can therefore be concluded that the reduction in rainfall and the increase in temperature should now be considered as factors of Argan woodland regression.

Multispectral remote sensing data may contain component images which are heavily corrupted by noise and pre-filtering (denoising) procedure is often applied to enhance these component images. To do this, one can use reference images – component images having relatively high quality and which are similar to the image subject to pre-filtering. Here we study the following problems: how to select component images that can be used as references (e.g., for the Sentinel multispectral remote sensing data) and how to perform the actual denoising. We demonstrate that component images of the same resolution as well as component images of a better resolution can be used as references. Examples of denoising of real-life images demonstrate high efficiency of the proposed approach.

Although urbanization has contributed to improving living conditions, it has had negative impacts on the natural environment in the urbanized areas. Urbanization has changed the urban landscape and resulted in increasing land surface temperature (LST). Thus, studies related to LST in various urban environments have become a popular research topic. However, few LST studies focusing on the mountain landscapes (i.e. hill stations) have been carried out. The primary objective of this study is to investigate changes in the landscape and their impacts on LST intensity (LSTI) in the tropical mountain city of Nuwara Eliya, Sri Lanka. The study utilized annual median temperatures extracted from Landsat data collected from 1996 to 2017 based on the Google Earth Engine (GEE) interface. The fractions of built-up (BL), forest (FL), and agricultural (AL) land were calculated using land use and cover maps based on the urban-rural zone (URZ) analysis. The urban-rural margin was demarcated based on the fraction of BL (<10%) and LSTI was measured using the mean LST difference in the urban-rural zone. In addition, the mixture of land use types was calculated using the AL/FL and BL/FL fraction ratios, and grid-based density analysis. The result shows that the BL in all URZ rapidly developed, while AL decreased during the period 1996 to 2017. There was minimal change in the forest area of the Nuwara Eliya owing to the government forest preservation policies. The fraction of the BL increased from 32.4% in 1996 to 58.7% in 2017 in the city center zone (URZ₁) resulting in increased mean LST by 4.7 °C. Furthermore, the increase of the BL/FL fraction ratio and the decrease of the AL/FL fraction ratio were positively correlated with the mean LST. Grid-based analysis showed an increasing positive relationship between mean LST and density of BL. This indicated that BL density has been a crucial element in increasing LST in the study area. The results of this study will be a useful indicator to introduce improved landscape and urban planning in the future to minimize the negative impact of LST on urban sustainability.

The use of the LMD technology as a manufacturing and repairing technique in industrial sectors like the die and mold and aerospace is increasing within the last decades. Research carried out in the field of LMD process situates argon as the most usual inert gas, followed by nitrogen. Some leading companies have started to use helium and argon as carrier and shielding gas, respectively. There is therefore a pressing need to know how the use of different gases may affect the LMD process due to there is a lack of knowledge with regard to gas mixtures. The aim of the present work is to evaluate the influence of a mixture of argon and helium on the LMD process by analyzing single tracks of deposited material. For this purpose, special attention is paid to the melt pool temperature, as well as to the characterization of the deposited clads. The increment of helium concentration in the gases of the LMD processes based on argon will have three effects. The first one is a slightly reduction of the height of the clads. Second, an increase of the temperature of the melt pool. Last, smaller wet angles are obtained for higher helium concentrations.

We performed a global analysis with data from 149 countries to test whether temperature can explain the spatial variability of the spread rate and mortality of COVID-19 at the global scale. We performed partial correlation analysis and linear mixed effect modelling to evaluate the association of the spread rate and motility of COVID-19 with maximum, minimum, average temperatures and temperature extreme (difference between maximum and minimum temperature) and other environmental and socioeconomic parameters. After controlling the effect of the duration after the first positive case, partial correlation analysis revealed that temperature was not related with the spatial variability of the spread rate of COVID-19. Mortality was negatively related with temperature in the countries with high-income economies. In contrast, temperature extreme was significantly and positively correlated with mortality in the low-and middle-income countries. Taking the country heterogeneity into account, mixed effect modelling revealed that inclusion of temperature as a fixed effect in the model significantly improved model skill predicting mortality in the low-and middle-income countries. Our analysis suggest that warm climate may reduce the mortality rate in high-income economies but in low and middle-income countries temperature extreme may increase the mortality risk.

This paper predict and effectively control the temperature distribution of the steady-state and transient states of anisotropic four-layer composite materials online, knowing the density, specific heat, heat conductivity and thickness of the composite materials. Based on the transfer function, a mathematical model was established to study the dynamic characteristics of heat transfer of the composite materials. First of all, the Fourier heat transfer law was used to establish a one-dimensional Fourier heat conduction differential equation for each composite layer, and the Laplace transformation was carried out to obtain the system function. Then the approximate second-order transfer function of the system was obtained by Taylor expansion, and the Laplace inverse transformation was carried out to obtain the transfer function of the whole system in the time domain. Finally, the accuracy of the simplified analytical solutions of the first, second and third order approximate transfer functions was compared with computer simulation. The results showed that the second order approximate transfer functions can describe the dynamic process of heat transfer better than others. The research on the dynamic characteristics of heat transfer in the composite layer and the dynamic model of heat transfer in composite layer proposed in this paper have a reference value for practical engineering application. It can effectively predict the temperature distribution of composite layer material and reduce the cost of experimental measurement of heat transfer performance of materials.

The There are many factors influencing the performance of photovoltaic (PV) systems. Among these factors, temperature and solar radiation are two major parameters that have a large effect on the efficiency of PV systems. The cell temperature of PV panels is related to the ambient temperature while the solar radiation incident on the surface of the PV modules depends on the slope and azimuth of these modules. Furthermore, ground reflectance (albedo) affects the irradiance incident on the PV panel surface, which in turn affects the output of a PV system. Nevertheless, the effects of these factors on the economic performance of the solar PV systems are scarcely reported. This paper presents a complete design of a stand-alone PV/battery system to supply electric power for a mobile base station in Choman, Erbil, Iraq. The effects of different factors on the total electricity produced by PV arrays and its economic performance are simultaneously investigated. HOMER software has been used as a tool for the techno-economic and environmental analysis. As indicated from the simulation results, the PV array capacity and its economic performance are highly affected by the variation of the slope and azimuth. With a base case (albedo of 20% and average annual ambient temperature of 11°C), the best feasible system which is achieved by facing PV due to south with a tilt angle of 40° or 45°, is found to have net present cost (NPC) of 70595 $ and cost of energy (COE) of 0.54 $/kWh. Moreover, the results indicate that increasing the ground reflectance from 10% to 90% results in a 7.2% decrease in the PV array capacity and about 3% decrease in the NPC and COE. On the other hand, increasing the ambient temperature from 0°C to 40°C results in a 19.7% increase in the PV array capacity and an 8.2% increase in the NPC and COE. Furthermore, according to the ambient temperature of Choman, using PV modules with high sensitivity to temperature is found to be an attractive option. Provided simulation performance analysis proves that the studied parameters must be treated well to establish an enabling environment for solar energy development in Iraq.

Surface urban heat island (SUHI) depicts the deteriorating thermal environment in high-density cities and local climate zone (LCZ) classification provides a universal protocol for SUHI identification. In this study, taking the central urbanized area of Guangzhou in the humid subtropical region of China as the study area, the maps or images of LCZ, land surface temperature (LST), SUHI and urban design factors were achieved by using Landsat satellite data, GIS database and a series of retrieval and classification algorithms, and the urban design factors influencing SUHI were investigated based on 625 samples of LCZs. The results show that in the summer daytime under the clear sky condition, the LST varied greatly from 26 °C to 40 °C and the SUHI changed in a wide range of -6 °C to 8 °C in the LCZs of the study area. Seven and five urban design factors influencing the summer daytime SUHI were identified for the two dominant LCZ of LCZs 1-5 (LCZ 1 to LCZ 5) and the mixed LCZ (containing at least three types of LCZs), respectively. The summer daytime SUHI prediction models were obtained by using the step-wise multiple linear regression, with the performance of R2 of 0.697, RMSE of 1.21 °C, and the d value of 0.81 for the model of LCZs 1-5, and the values of 0.666, 1.66 °C, and 0.76 for the model of the mixed LCZ, indicating that the models can predict the changes of SUHI with LCZs to a large and satisfactory extent. This study presents a methodology to efficiently achieve a large sample of SUHI and urban design factors of LCZs in the largely urbanized cities, and provides information beneficial to the urban designs and regenerations in the humid subtropical region.

The coronavirus disease 2019 (COVID-19) pandemic is the defining global health and socioeconomic crisis of our time and represents the greatest challenge faced by the world since the end of the Second World War. The academic literature indicates that climatic features, specifically the temperature and absolute humidity, are very important factors affecting infectious pulmonary disease epidemics (e.g., SARS, MERS); however, the influence of climatic parameters on COVID-19 remains extremely controversial. The goal of this study is to quantify the existing relationship between several daily climate parameters (temperature, relative humidity, accumulated precipitation, solar radiation, wind direction and intensity, and evaporation), local morphological parameters, and new daily positive swabs for COVID-19, which represents the only parameter that can be statistically used to quantify the pandemic. The daily deaths parameter was not considered because it is not reliable due to frequent administrative errors. Daily data on meteorological conditions and new cases of COVID-19 were collected for the Lombardy area from March 1, 2020, to April 20, 2020. This region in Italy exhibited the largest number of official deaths in the world per million inhabitants, with a value of approximately 1700 per million on june 30, 2020. Moreover, the apparent lethality was approximately 17% in this area, mainly due to the considerable housing density and the extensive presence of industrial and craft areas. The Mann-Kendall test and multivariate statistical analysis showed that none of the considered climatic variables exhibited statistically significant relationships with the epidemiological evolution of COVID-19, at least in the spring months in temperate subcontinental climate areas, with the exception of solar radiation, which was directly related and showed an otherwise low explained variability of approximately 20%. Furthermore, the average temperatures of two highly representative meteorological stations of Molise and Lucania, the most weakly affected by the pandemic. The temperatures at these stations were approximately 1.5°C lower than that in the cities in Lombardy of Bergamo and Brescia, again confirming that a significant relationship between the increase in temperature and decrease in virology from COVID-19 was not evident, at least in the Italian peninsula.

Traditional ways of validating satellite-derived sea surface temperature (SST) and sea surface salinity (SSS) products, using comparisons with buoy measurements, do not allow for evaluating the impact of mesoscale to submesoscale variability. Here we present the validation of remotely-sensed SST and SSS data against the unmanned surface vehicle (USV) – Saildrone – measurements from the Spring 2018 Baja deployment. More specifically, biases and root mean square differences (RMSD) were calculated between USV-derived SST and SSS values, and six satellite-derived SST (MUR, OSTIA, CMC, K10, REMSS, and DMI) and three SSS (JPLSMAP, RSS40, RSS70) products. Biases between the USV SST and OSTIA/CMC/DMI were approximately zero while MUR showed a bias of 0.2C. OSTIA showed the smallest RMSD of 0.36C while DMI had the largest RMSD of 0.5C. An RMSD of 0.4C between Saildrone SST and the satellite-derived products could be explained by the daily variability in USV SST which currently cannot be resolved by remote sensing measurements. For SSS, values from the JPLSMAP product showed saltier biases of 0.2 PSU, while RSS40 and RSS70 showed fresh biases of 0.3 PSU. An RMSD of 0.4 PSU could not be explained solely by the daily variability of the USV-derived SSS. Coherences were significant at the longer wavelengths, with a local maximum at 100 km that is most likely associated with the mesoscale turbulence in the California Current System.

Grazing incidence X-Ray Diffraction spectroscopy was employed to characterize crystallinity of Iron, Nickel, Copper and Tungsten, prepared by sparking discharge process in presence of 0.4 T magnetic field at ambient temperature 25 °C. Iron thin film preserved crystallinity even after one year of ageing. Nickel exhibit higher crystallinity when sparked in nitrogen gas flow from the one sparked in oxygen. Tungsten was successfully crystalized after just 40 minutes of sparking inside of magnetic field.

Salmon farming has been blamed for the collapse of the sea trout (Salmo trutta) fishery in Loch Maree on Scotland’s west coast despite the absence of any direct evidence. Stocks of west coast demersal marine fish, especially around the Clyde Estuary have also declined over a similar time span. The decline of these marine fish stocks can be attributed to the removal of the “three-mile fishing limit” in 1984 by UK Government legislation. Sea trout inhabit the same inshore waters as targeted demersal fish and can be caught as by-catch. Comparisons of the decline of demersal species and the sea trout from Loch Maree and the west coast show a high degree of correlation. Stocks of whiting (Merlangius merlangus) from inshore waters have found to consist of small fish which mirrors the stock makeup of the Loch Maree sea trout stock.

This paper presents the results of hot smoke tests, conducted in a real road tunnel. The tunnel is located within the expressway S69 in southern Poland between cities Żywiec and Zwardoń. Its common name is Laliki tunnel. It is a bi-directional non-urban tunnel. The length of the tunnel is 678 m and it is inclined by 4%. It is equipped with the longitudinal ventilation system. Two hot smoke tests have been carried out according to Australian Standard AS 4391-1999. Hot smoke tests corresponded to a HRR (Heat Release Rate) equal to respectively 750 kW and 1500 kW. The fire source was located in the middle of the road lane imitating an initial phase of a car fire (respectively 150 m and 265 m from S portal). The temperature distribution was recorded during both tests using a set of fourteen thermocouples mounted at two stand poles located at the main axis of the tunnel on windward. The stand poles were placed at distances of 5 m and 10 m. The recorded data were applied to validate of a numerical model built and solved using Ansys Fluent. The calculated temperature distribution matched the measured values.

The present paper proposes a fractal analysis of the Covid-19 dynamics in 45 European countries. We introduce a new idea of using the box-counting dimension of the epidemiologic curves as a means of classifying the Covid-19 pandemic in the countries taken into consideration. The classification can be a useful tool in deciding upon the quality and accuracy of the data available. We also investigated the reproduction rate, which proves to have significant fractal features, thus enabling another perspective on this epidemic characteristic. Moreover, we studied the correlation between two meteorological parameters: global radiation and daily mean temperature and two Covid-19 indicators: daily new cases and reproduction rate. The fractal dimension differences between the analysed time series graphs could represent a preliminary analysis criterion, increasing research efficiency. Daily global radiation was found to be stronger linked with Covid-19 new cases than air temperature (with a greater correlation coefficient -0.386, as compared with -0.318), and consequently it is recommended as the first-choice meteorological variable for prediction models.

Very hot (> 65 °C) beverages such as espresso were evaluated by the International Agency for Research on Cancer (IARC) as probably carcinogenic to humans. For this reason, research into lowering beverage temperature without compromising its quality or taste is important. For espresso, one obvious possibility consists in lowering the brewing temperature. In two sensory trials using ISO 4120:2004 triangle test methodology, brewing temperatures of 80°C vs. 128°C and 80° vs. 93°C were compared. From the tested levels, espresso brewed at the lowest temperature had the highest acceptance. However, most tasters were unable to distinguish between 80°C and 93°C. The results of these pilot experiments proof the possibility to decrease the health hazard of very hot beverages by lower brewing temperatures.

Coronavirus disease is a newly identified infectious disease that began in Wuhan, China in 2019 and is recognized as COVID-19. This virus has a serious impact on the planet that causes the deaths of millions of people; it produces unemployment and poverty. However, it has constructive environmental effects that reduce the amount of pollution in the atmosphere. Pakistan is also a developing economy caused by this deadly virus. Before 03 April 2021, the percentage of reported cases ranges from 682,888, with about 14,697 casualties and a total of 609,691 cases retrieved. Pakistan’s war against coronavirus can differ from advanced technical countries due to lack of resources. In this article, we will address the relation between COVID-19 and the environment in the particular case of Pakistan. There is evidence that this pandemic has lowered concentrations of greenhouse gases, including CO2 and NO2, as a consequence of global lock-down strategies.

Based on 541 Landsat images between 1988 and 2016, the normalized difference vegetation indices (NDVIs) of the wetland vegetation at Xitugou (XTG) and Wowachi (WWC) inside the Dunhuang Yangguan National Nature Reserve (YNNR) in northwest China were calculated for assessing impacts of climate change on wetland vegetation in the YNNR. It was found that the wetland vegetation at the XTG and WWC both had shown a significant increasing trend in the past 30 years, and the increase in both annual mean temperature and peak snow depth over the Altun Mountains led to the increase of wetland vegetation. The influence of local precipitation on the XTG wetland vegetation was greater than on the WWC wetland vegetation, which demonstrates that in extremely arid regions, the major constrain to the wetland vegetation is water availability in soils which is greatly related to the surface water detention and discharge of groundwater. At both XTG and WWC, snowmelt from the Altun Mountains is the main contributor to the groundwater discharge, while local precipitation plays a less role in influencing the wetland vegetation at the WWC than at the XTG, because the wetland vegetation grows on a relatively flat terrain at the WWC, while in a stream channel at the XTG.

There is a perception among the inhabitants of the Aburrá Valley Region, that this heavily populated region, situated in the Andean mountains of Colombia, has been suffering large temperature raises in the last years, especially in the last decade. To give perspective about this issue, the authors have gone through the available information about temperature changes in three meteorological stations in the region and have correlated it with a set of variables of urban, climatic and energetic nature, with the intention of developing an approximate model to understand the temperature changes. Changes in the mean temperature, based on the linear tendencies, were estimated on 0.47ºC for the 20 years between 1995 and 2015; 60% of change was found to be related to local human activities and 40% was attributed to the impact of global warming.

Epidemiological studies indicate an increased risk of cancer from the consumption of very hot foods and beverages. The International Agency for Research on Cancer (IARC) has already recommended threshold values for the maximum drinking temperature of very hot beverages. The contact time and the contact temperature are decisive for the risk of injury when hot media come into contact with human skin. However, measuring the contact temperature is not easily possible in practice. In the present study, a numerical simulation based on the solution of the heat conduction equation was initially used to investigate whether and for what period of time a constant contact temperature is to be expected under oral conditions. For small circular 3-cm food samples (e.g., cooked potatoes) with 2.5 mm thickness in contact with the tongue, the simulation results in a constant contact temperature of 10 s before cooling. With a thickness of 0.5 mm, the contact temperature is only maintained 1 s. Hot beverages, which spread as a thin film and thereby increase their surface area, can therefore be consumed at higher temperatures than solid foods. Furthermore, a simple test technique with a "measuring spoon" was developed. A hot sample is placed on the tongue. Orientating measurements were used to determine which contact temperature was considered to be just comfortable for any period > 10 s and for which period of less than 10 s it was still just bearable. The contact temperature, which was still perceived as tolerable for periods > 10 s, was 46.5 °C. The time spans for the higher contact temperature 48 °C were between 2 and 4 s and for 49 °C between 1 and 2 s. The course of the contact temperatures determined in the experiment over time allows to calculate the corresponding threshold values of consumption temperatures for various foods. Consumption temperatures of about 56 °C for potatoes and 60 °C for cheese are still perceived as tolerable. In view of the fact that the contact temperature is obviously the determining factor for the risk of injury from burns in the oral cavity in addition to the contact time, it makes sense to reference threshold values to the contact temperature rather than to the surface or consumption temperature of a food product, which is current customary practice. If this contact temperature is defined as a threshold value, the surface or consumption temperature for any other food can be calculated.

A method of direction-of-arrival (DoA) estimation for FMCW radars is presented. In addition to MUSIC and ESPRIT, which are well-known high-resolution DoA estimation algorithms, deep learning has recently emerged as a very promising alternative. It is proposed in this paper to use a 3D convolutional neural network (CNN) for DoA estimation. The 3D-CNN extracts from the radar data cube spectrum features of the region of interest (RoI) centered on the potential positions of the targets, thereby capturing the spectrum phase shift information, which corresponds to DoA, along the antenna axis. Finally, the results of simulations and field experiments are provided to demonstrate the superior performance, as well as the limitations, of the proposed 3D-CNN.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP strips, to increase the out-of-plane strength of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips placed on the two faces of the masonry wall gives rise to an I-beam behavior of the facing CFRP strips, which begin to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering actions provided by the floors on the perimeter walls, during an earthquake. Lastly, after the building went out of service, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

Maritime Continent (MC) positions in between Asian and Australian summer monsoons zone. Its complex topography and shallow seas around it is a major challenge for the climate researchers to model and understand it. Monsoon in this area is affected by inter-scale ocean-atmospheric interactions like El-Niño Southern Oscillation (ENSO), Indian Ocean Dipole (IOD) and Madden-Julian Oscillation. Monsoon rainfall in MC (especially in Indonesia and Malaysia) profoundly exhibits its variability dependency on ocean-atmospheric phenomena in this region. This monsoon shift often introduces to dreadful events like biomass burning (BB) in Southeast Asia (SEA) which sometimes leads to severe trans-boundary haze pollution. In this study, the episode of BB in 2015 of SEA is highlighted and discussed. Observational satellite datasets are tested by performing simulations with numerical weather prediction (NWP) model using WRF-ARW (Advanced research WRF). Observed and model datasets are compared to study the sea surface temperature (SST) and precipitation (rainfall) anomalies influenced by ENSO, IOD and MJO. Correlations have been recognised which explains the delayed rainfall of regular monsoon in MC due to the influence of ENSO, IOD and MJO during 2015 BB episode, eventually leading to intensification of fire and severe haze.

There is a perception among the inhabitants of the Aburrá Valley Region, that this heavily populated region, situated in the Andean mountains of Colombia, has been suffering large temperature elevations in the last years, especially in the last decade. To give perspective about this issue, the authors have gone through the available information about temperature changes in three meteorological stations in the region and have correlated it with a set of variables of urban, climatic and energetic nature, with the intention of developing an approximate model to understand the temperature changes. Changes in the mean temperature, based on the linear correlation of the data were estimated on 0.47oC for the 20 years between 1995 and 2015; the study showed that 60% of change was found to be related to local human activities and 40% was attributed to the impact of global warming. For the local influences some practical mitigation actions are proposed, related to improve the energy management and paying more attention to the temperature changes trough improvements in the number and capability of sampling stations in the urban air and in the river, which serve as clear indicators of the changes and the effect of any mitigation measures.

Recently, some authors have developed a shell-less culture system for chick embryos by using a plastic lm as culture vessels. We will show that velocity of rotation of vessels in incubator and temperature have direct relations with growth of chick embryos. We also obtain a mathematical relation between velocity, temperature and rate of growth of chick embryo.

Rapid and extensive urbanization has adversely impacted humans and ecological entities in the recent decades through a decrease in surface permeability and the emergence of urban heat islands (UHI). While detailed and continuous assessments of surface permeability and UHI are crucial for urban planning and management of landuse zones, they have mostly involved time consuming and expensive field studies, and single sensor derived large scale aerial and satellite imageries. We demonstrated the advantage of fusing imageries from multiple sensors for landuse and landcover (LULC) change assessments as well as for assessing surface permeability and UHI emergence in Tirunelveli, Tamilnadu, India. Cartosat-2 and Landsat-7 ETM+ imageries from 2007 and 2017 were fused and classified using a Rotation Forest (RF), while surface permeability and temperature were quantified using Soil-Adjusted Vegetation Index (SAVI) and Land Surface Temperature (LST) index, respectively. Fused images exhibited higher classification accuracies than non-fused images, i.e. overall kappa coefficient values 0.83 and 0.75, respectively. We observed an overall increase of 20 km2 (45%) in the coverage of urban (dry, real estate plots and built-up) areas, while a decrease of 27 km2 (37%) for vegetated (cropland and forest) areas in Tirunelveli between 2007 and 2017. The SAVI values indicated an extensive decrease in surface permeability for Tirunelveli overall (0.4) and also for almost all LULC zones. The LST values exhibited an associated overall increase (1.30C) of surface temperature in Tirunelveli with the highest increase (2.40C) for urban built-up areas between 2007 and 2017. The SAVI-LST combined metric depicted the Southeastern built-up areas in Tirunelveli as a potential UHI hotspot, while a caution for the Western riparian zone for UHI emergence in 2017. Our results provide important metrics for surface permeability and UHI monitoring, and inform urban and zonal planning authorities about the advantages of satellite image fusion.

An all-weather land surface temperature (LST) product derived at the Satellite Application Facility on Land Surface Analysis (LSA-SAF) is presented. The product is based on clear-sky LST retrieved from MSG/SEVIRI infrared (IR) measurements, complemented by LST estimated with a land surface energy balance (EB) model to fill gaps caused by clouds. The EB model solves the surface energy balance mostly using products derived at LSA-SAF. The new product is compared with in situ observations made at 3 dedicated validation stations, and with a Microwave (MW) based LST product derived from AMSR-E measurements. The validation against in-situ LST indicates an accuracy of the new product between -0.8 K and 1.1 K and a precision between 1.0 K and 1.4 K, generally showing a better performance than the MW product. The EB model shows some limitations concerning the representation of the LST diurnal cycle. Comparisons with MW LST generally show higher LST of the new product over desert areas, and lower LST over tropical regions. Several other imagers provide suitable measurements for implementing the proposed methodology, which offers the potential to obtain a global, nearly gap-free LST product.

Carburizing of stainless steels at low temperatures (below 500°C) develops a high content carbon layer, known for its high hardness. X-ray Diffraction investigation indicates that carburization treatment does not impact the structure of substrate; however, introduced carbon causes expansion in the carburized layer through the increase in d-spacing. Characterization of carbon concentration and hardness profiles indicate that carbon content gradually decreases while moving further into the substrate; and the origin of the increased hardness of the expanded layer arises from the super-saturated carbon content, following the solid solution strengthening theory. An area that is not well understood is in regard to the carburized layer’s relation to the substrate and the significance in their differences. Using two grades of stainless steel, AISI 316L and PH 17-4, it was observed that the carburized layer is not a separate layer, but a higher carbon content version of the substrate,

This research is aimed at determining the characteristics of the current level of entrepreneurial potential of the Three Seas Initiative (3SI) countries, the ability to overcome the consequences of extraordinary events, such as COVID-19 and prospects for the return to an accelerated development once the destabiliser of the economic system, the coronavirus pandemic, has ceased. Eurostat, World Bank and the World Economic Forum data for 2015-2019 were used for the purpose of the research. The research was divided into three stages, i.e. assessment of economic development on the basis of a synthetic ratio of economic anchor development, for which a relative benchmark method based on spatial median (so-called L1 median or Weber point) was used, identification of conditions for the development of entrepreneurial capacity and statistical analysis showing the correlation between economic anchor measures and selected factors of the 3SI countries economic development. Our study found that the entrepreneurial capacity of the 3SI countries in 2015-2019 was determined by nine characteristics, belonging to six areas, i.e. local economy, demographic situation, social situation, trade exchange, innovation and tourism economy. The entrepreneurial potential of the 3SI countries was spatially diversified, and its development was determined, among others, by the entrepreneurial activity of residents (entrepreneurship index) and the conditions for running a business.

Recent in vivo assays of the responses of Rubisco to temperature in C₃ plants have revealed substantial diversity. Three cultivars of soybean (Glycine max L. Merr.), Holt, Fiskeby V, and Spencer, were grown in indoor chambers at 15, 20, and 25 ^oC. Leaf photosynthesis was measured over the range of 15 to 30 ^oC, deliberately avoiding higher temperatures which may cause deactivation of Rubisco, in order to test for differences in temperature responses of photosynthesis, and to investigate in vivo Rubisco kinetic characteristics responsible for any differences observed. The three cultivars differed in the optimum temperature for photosynthesis (from 15 to 30 ^oC) at 400 µmol mol^-1 external CO₂ concentration when grown at 15 ^oC, and in the shapes of the response curves when grown at 25 ^oC. The apparent activation energy of the maximum carboxylation rate of Rubisco differed substantially between cultivars at all growth temperatures, as well as changing with growth temperature in two of the cultivars. The activation energy ranged from 58 to 84 kJ mol-1, compared with the value of 64 kJ mol^-1 used in many photosynthesis models. Much less variation in temperature responses occurred in photosynthesis measured at nearly saturating CO₂ levels, suggesting more diversity in Rubisco than in electron transport thermal properties among these soybean cultivars.

The Equator Principle is the goal of promoting the harmonious development of my country's economy and society. It promotes the green transformation and upgrading of the industrial structure by strictly controlling the flow of commercial bank funds, so as to achieve the goal of environmental protection and the coordinated development of the national economy. This paper uses factor analysis to reduce the dimensions of 10 financial indicators and non-financial indicators that measure the operating performance and development potential of joint-stock commercial banks, and then compares the comprehensive operating performance, liquidity, and safety of Industrial Bank and comparable banks. And the level of profitability, analyze the difference in comprehensive operating performance of joint-stock commercial banks joining the Equator Principles compared with commercial banks that have not joined the Equator Principles. The results of the study found that joining the Equator Principles of joint-stock commercial banks can improve comprehensive operating performance in the short term. In the long run, the development trend of Industrial Bank will be similar to that of comparable banks in the same category. Joining the Equator Principles of Industrial Bank can improve its liquidity and profitability, but it will not in the long run. Conducive to the improvement of the asset quality of joint-stock commercial banks. In this regard, the government, enterprises and financial institutions should work together to help commercial banks achieve an effective balance between operating performance and social responsibility, so as to achieve the goals of "carbon peak" and "carbon neutral".

High temperature (HT) significantly affects the crop physiological traits and reduces the 12 productivity in plants. To increase yields as well as survival of crops under HT, developing heat13 tolerant plants is one of the main targets in crop breeding programs. The present study attempted 14 to investigate the linkage of the heat tolerance between the seedling and the reproductive growth 15 stages of tomato cultivars ’Dafnis‘ and ’Minichal’. This research was undertaken to evaluate heat 16 tolerance under two experimental designs such as screening at seedling stage and screening from 17 reproductive traits in greenhouses. Survival rate and physiological responses in seedlings of 18 tomatoes with 4-5 true leaf were estimated under HT (40 °C, RH 70%, day/night, respectively) and 19 under two control and HT greenhouse conditions (day time 28 °C and 40 °C, respectively). Heat 20 stress significantly affected physiological-chemical (photosynthesis, electrolyte conductivity, 21 proline) and vegetative parameters (plant height, shoot fresh weight, root fresh weight) in all 22 tomatoes seedlings. The finding revealed that regardless of tomato cultivars the photosynthesis, 23 chlorophyll, total proline and electrical conductivity parameters were varied in seedlings during the 24 heat stress period. The heat tolerance rate of tomatoes in the seedling stage might not be associated 25 always with reproductive parameters. HT reduced the fruit parameters likeas fruit weight (31.9%), 26 fruit length (14.1%), fruit diameter (19.1%) and fruit hardness (9.1%) in compared to NT under HT 27 in heat susceptible tomato cultivar ‘Dafnis’, while in heat tolerant cultivar ‘Minichal’ fruit length 28 (7.1%) and fruit diameter (12.1%) was decreased by the affect of HT but on the contrary fruit weight 29 (3.6%) and fruit hardness (8.3%) were increased. In conclusion, screening and selection for tomatoes 30 should be evaluated at the vegetative and reproductive stages with consideration of reproductive 31 parameters.

Water hyacinth (Eichhornia crassipes) is an invasive species that has modified ecosystem functioning in the Sacramento-San Joaquin Delta (Delta), California, USA. Studies in lakes and rivers have shown that water hyacinth alters water quality. In tidal systems, such as the Delta, water moves back and forth through the water hyacinth patch so water quality directly outside the patch in either direction is likely to be impacted. In this study, we asked whether the presence or treatment of water hyacinth with herbicides resulted in changes in water quality in this tidal system. We combined existing datasets that were originally collected for permit compliance and long-term regional monitoring into a dataset that we analyzed with a before-after control-impact (BACI) framework. This approach allowed us to describe effects of presence and treatment of water hyacinth, while accounting for seasonal patterns in water quality. We found that although effects of treatment were not detectable when compared with water immediately upstream, dissolved oxygen and turbidity became more similar to regional water quality averages after treatment. Temperature became less similar to the regional average after treatment, but the magnitude of the change was small. Taken together, these results suggest that tidal hydrology exports the effects of water hyacinth upstream, just as river flow is known to transport the effects downstream, creating a buffer of altered water chemistry around patches. It also suggests that although water hyacinth has an effect on dissolved oxygen and turbidity, these parameters recover to regional averages after treatment.

innate and adaptive immune responses lead to wound healing by regulating a complex series of events promoting cellular cross-talk. An inflammatory response is presented with its characteristic clinical symptoms: heat, pain, redness, and swelling. Some smart thermo-responsive polymers like chitosan can be used to create biocompatible and biodegradable scaffolds with 3D architectures similar to human structures, allowing their efficient and safe use as tissue engineering and drug delivery systems in chronic wounds. Locally heated tumors above polymer lower critical solution temperature can induce its conversion into a hydrophobic form, enhancing drug release until the thermal stimulus is gone, where a lower release is due to the swelling of the material. This paper integrates the relevant reported contributions of bioengineered scaffolds for thermo-responsive drug delivery in wound healing. Therefore, we present a comprehensive review that aims to demonstrate the capacity of these systems to provide spatially and temporally controlled release strategies for one or more drugs used in wound healing. In this sense, the novel manufacturing techniques of 3D-printing and electrospinning are explored for the tuning of their physicochemical properties to adjust therapies according to the patient’s convenience, as well as reduce drug toxicity and side effects.

Developing particles of different geometric anisotropic shapes are the hot topic since decades as they guarantee some special features of properties not possible through other means. Again, controlling atoms to develop certain size and shape particle is a quite challenging job. In this study, gold particles of different shapes are developed via pulse-based electronphoton-solution interface process. Here, it is discussed that gold atoms under certain transition state amalgamated at solution surface to develop monolayer assembly around the light glow of electrons and photons, which is known in plasma, generating through flowing argon gas copper capillary, which is known in cathode. The rate of uplifting gold atoms to solution surface is controlled under the fixed optimized entrance of forced energy electron streams and photons of high forcing energy. Uplifting gold atoms dissociated on dissociation of precursor under the dissipating heat energy resulted by propagating photonic current through graphite rod immersed in the solution, which is known in anode. On the other hand, packets of nano shape energy resulted by the controlled tuned pulse protocol developing tiny particles of own shape by binding transition state atoms of compact monolayer assembly. At solution surface, adjusting atoms of monolayer tiny particle into one-dimensional arrays under the disconcerted lateral forces following by their elongation under uniformly exerted opposite poles forces. This results into convert them in a structure of smooth elements where adjacently placed electrons and those in the outer rings of elongated atoms inter-connecting side-to-side by introducing orientational-based stretching of clamped energy knots. Tiny sized particles developed their atoms of one-dimensional arrays in structure of smooth elements exert an immersing force at favorable side tips and where many such tiny particles around the light glow work as one unit for each case resulting into pack by inter-connecting at inside their common point to nucleate the shape of certain particle. Depending on the development zone of such tiny sized particles and their amount of simultaneous packing under naturally maintained orientations develop their different geometric anisotropic shaped particles. At fixed precursor concentration, increasing the process time results into develop particles of low aspect ratio. Under tuned parameters, developing mechanisms of particles of high aspect ratio exhibiting unprecedented features are discussed.

Most of the commonly used Ionic Liquids (ILs) contain bulky organic cations with suitable anions. With our COMPLET (Concept of Melting Point Lowering due to Ethoxylation), we follow a different approach. We use simple, low-toxic, cheap and commercially available anions of the type Cx(EO)yCH2COO– to liquefy presumably any simple metal ion, independently of its charge. In the simplest case, the cation can be sodium or lithium, but synthesis of Ionic Liquids is also possible with cations of higher valences such as transition or rare earth metals. Anions with longer alkyl chains are surface active and form surface active ionic liquids (SAILs), which combine properties of ionic and nonionic surfactants at room temperature. They show significant structuring even in their pure state, i.e. in the absence of water or any other added solvent.

One of the most destructive natural disasters is the earthquake which brings enormous risks to humankind. The objective of the current study was to determine the Earthquake’s remote sensing multiparameter (i.e. land surface temperature (LST), air temperature, specific humidity, precipitation and wind speed) spatiotemporal anomaly of many earthquake samples occurred during 2018 around the world. In this research 11 earthquake (M > 6:0) studied (4 samples selected in a land with transparent sky situations, 3 samples in land within cloudy situations and 4 samples in marine earthquakes). The interquartile range (IQR) and mean ± 2σ methods utilized to improve the efficiency of anomalous differences. As a result, based on the IQR method, negative anomaly before the event detected during the daytime in Mexico and during the nighttime in Afghanistan. In addition, a negative outlier of brightness temperature (BT) detected in Alaska before, after and during the event. In contrast, based on IQR and mean ± 2σ positive anomaly detected in precipitation before and after the event in all investigated examples. According to mean ± 2σ, negative anomaly LST, specific humidity, sea surface temperature (SST_100) and wind detected in most examined earthquake samples. In contrast, positive SST_0 anomaly observed in Fiji and Honduras after the earthquake. Our results suggested in marine earthquakes, for earthquake forecasting we can merge a prior negative anomaly in the wind speed and SST_100. Regarding the in land cloudy sky earthquakes, merging anomaly parameters could be the negative prior anomaly in BT, skin temperature, in contrast, a positive anomaly in precipitation. In land transparent sky earthquake, usually negative prior anomalies in air temperature, specific humidity and LST.

In the paper, an improved smart meter data-based three-stage algorithm to calculate the power/energy losses in the three-phase networks with the voltage level below 0.4 kV (low voltage - LV) is presented. In the first stage, a loading function of input data was built having as main feature the working at the same time with files from the database of smart metering system (SMS) containing the hourly electricity records, and files including the characteristic load profiles established by the Distribution Network Operator (DNO) for the consumers with standard energy meters depending the following factors: consumption class, day and season. In the second stage, a function which is based on the work with the structure vectors was implemented to identify easy the configuration of analysed networks. In the third stage, an improved version of forward/backward sweep-based algorithm was proposed to calculate fast the power/energy losses to three-phase LV distribution networks in balanced and unbalanced regime. A real LV rural distribution network from a pilot zone belonging to a Distribution Network Operator (DNO) from Romania was used to confirm the accuracy of the proposed approach. The comparison with the results obtained using the DigSilent PowerFactory Simulation Package certified the performance of the algorithm, the mean absolute percentage error (MAPE) being 0.94%.

Empirical Colebrook equation from 1939 is still accepted as an informal standard to calculate friction factor during the turbulent flow (4000 < Re < 10⁸) through pipes from smooth with almost negligible relative roughness (ε/D→0) to the very rough (up to ε/D = 0.05) inner surface. The Colebrook equation contains flow friction factor λ in implicit logarithmic form where it is, aside of itself; λ, a function of the Reynolds number Re and the relative roughness of inner pipe surface ε/D; λ = f (λ, Re, ε/D). To evaluate the error introduced by many available explicit approximations to the Colebrook equation, λ ≈ f(Re, ε/D), it is necessary to determinate value of the friction factor λ from the Colebrook equation as accurate as possible. The most accurate way to achieve that is using some kind of iterative methods. Usually classical approach also known as simple fixed point method requires up to 8 iterations to achieve the high level of accuracy, but does not require derivatives of the Colebrook function as here presented accelerated Householder’s approach (3^rd order, 2^nd order: Halley’s and Schröder’s method and 1^st order: Newton-Raphson) which needs only 3 to 7 iteration and three-point iterative methods which needs only 1 to 4 iteration to achieve the same high level of accuracy. Strategies how to find derivatives of the Colebrook function in symbolic form, how to avoid use of the derivatives (Secant method) and how to choose optimal starting point for the iterative procedure are shown. Householder’s approach to the Colebrook’s equations expressed through the Lambert W-function is also analyzed. One approximation to the Colebrook equation based on the analysis from the paper with the error of no more than 0.0617% is shown.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

The use of different primary energy sources in human society has led to two major polluting emissions in the environment: energy (mostly heat), and chemical substances (mostly carbon dioxide). In this paper, the total global anthropogenic emissions of heat to the atmosphere during the industrial era (years 1850-2018) were determined and their effect on the change of global atmospheric temperature was calculated. The concept of a theoretical three-phase Earth reactor was introduced to estimate global atmospheric temperature increase caused by anthro-pogenic heat emissions. The resulting calculations closely approximated the actual atmospheric temperature change recorded during the last 170-year period. These results suggest that the temperature change of the atmosphere (global warming) is entirely due to anthropogenic heat emissions.

The article introduces a new solution approach to grid-connected single-stage three-phase PV inverter whereby a dc-link voltage can successfully achieve the desired performance. As a single-stage, the variable output of perturb and observe maximum power point tracking (P&O based-MPPT) is fully utilized as dc-link voltage reference in inverter control scheme. As a result, it is challenging for the dc-link voltage to preserve energy balance by tracking its variable dc-link voltage reference under unpredictable environmental changes. To overcome this challenge, an adaptive reference proportional-integral (ARPI) controller, self-tuning, is designed and implemented to compel the dc-link voltage tracking its voltage reference to be equal as closely as possible; hence, the capability of the dc-link under abnormal events substantially guarantees the best energy balance and transient performance enhancement. To verify the validity of the method, simulation results for multiple events scenarios on 250 KW single-stage grid-connected PV systems show the effectiveness of the ARPI controller compared with PI controller.

The improvement of the methane combustion activity was observed in cyclic temperature-programmed and isothermal reactions over Pd/ZrO2 catalysts by simple reduction/re-oxidation treatment. The catalytic activity increased during the initial stages of isothermal reaction, and the light-off temperature was lowered as the number of cycles increased in the cyclic temperature-programmed reaction. To reveal the origin of activation, variations in the reduction properties after the activation period were carefully investigated through CH4 temperature-programmed reduction (TPR) measurements. From the CH4-TPR results, it was confirmed that the reduction temperature decreased significantly after activation. The observation of the CH4-TPR peak at relatively low temperatures is directly proportional to the catalytic activity of CH4 combustion. It was therefore concluded that repeated reduction/re-oxidation occurred in the reactant stream, and this phenomenon allowed the combustion reaction to proceed more easily at lower temperatures.

Lack of due attention to the orientation of streets and establishment of urban blocks without regard for climatic characteristics and conditions of the environment have an adverse effect on thermal comfort in open urban spaces. Construction of new settlements without taking into account climatic requirements undermines thermal comfort for pedestrians and other users, especially in cold regions. Considering the coldness of the region under study and the significance of the orientation of streets in absorbing radiation and providing heat to outdoor urban spaces, this study investigates the effect of the orientation of streets on microclimatic comfort in one of the residential towns of Hamadan City in Iran. For this purpose, microclimate simulation was performed using ENVI-met software. A residential block with four different orientations (the most common orientations of its surrounding buildings) were simulated in the coldest day of winter and the hottest day of summer. The results suggest that streets have different thermal behavior in different orientations. Orientation affects mean radiant temperature (Tmrt), the duration of exposure to direct sunlight, wind speed, and physiological equivalent temperature (PET), which are all important factors in thermal comfort. Based on these findings, north-south streets in Hamedan receive more radiant temperature during winter compared to other simulated orientations and provide more desirable thermal comfort. The average PET value on a winter day at a point on the north-south passage was 4.5-8 °C warmer than other orientations. In summer, streets with intercardinal orientations (i.e., northeast-southwest and northwest-southeast) provided the lowest PET (about 2 °C cooler than other orientations) and better thermal comfort

The objective of this study was to evaluate biomarkers of heat stress (HS) from automatic milking system (AMS), the relationships between measurements of temperature-humidity index (THI) and reticulorumen ph and temperature and some automatic milking systems parameters in dairy cows (rumination time (RT), milk traits, body weight (BW) and consumption of concentrate (CC)) during summer period. The experiment was carried out on a dairy farm at 54.9587408, 23.784146. Lithuanian Black and White dairy cows (n=365) were selected. The cows were milked with Lely Astronaut® A3 milking robots with free traffic. The rations were calculated to meet physiological requirements of the animals. Daily milk yield, rumination time, body weight, milk fat and protein ratio were collected from the Lely T4C management program for analysis. The pH and temperature of the contents of cow reticulorumen were measured using specific smaX-tec boluses manufactured for animal care. The daily humidity and air temperature in the farm zone were obtained from the adjacent weather station (2 km away). According this study during HS, the higher THI had positive correlation with ML, which show tendencies to increase risk of mastitis, and decrease CC, RT, BW, MY, reticulorumen ph and F/P. Some biomarkers of HS can be milk yield, milk lactose, somatic cell count, concentrate conception, rumination time, body weight, reticulorumen ph and milk fat – protein ratio. We can recommend to monitoring these parameters in the herd management program to identify possibility of heat stress.

In this paper, by developing a mathematical model, the operating temperature of perovskite solar cells (PSCs) under different operating conditions has been calculated. It is found that by reducing the density of tail states at the interfaces, acting as recombination centres, through some passivation mechanisms, the operating temperature can be reduced significantly at higher applied voltages. The results show that if the density of tail states at the interfaces is reduced by three orders of magnitude through some passivation mechanisms, then the active layer may not undergo any phase change up to an ambient temperature 300 K and it may not degrade up to 320 K. The calculated heat generation at the interfaces at different applied voltages with and without passivation shows that the heat generation can be reduced by passivating the interfaces. It is expected that this study may provide a deeper understanding of the influence of interface passivation on the operating temperature of PSCs.

Droughts occurring more and more frequently in recent years are usually associated with progressive climate changes. Modern monitoring methods is mainly associated with agricultural use due to the high market demand for services protecting against agricultural losses. In natural wetland ecosystem this problem is neglected which is probably due to fact that this are ecosystems rich in water by definition. Nevertheless this droughts might become a problem of wetlands, whose good condition depends on adequate hydration. Therefore this study focused on determination Crop Water Stress Index (CWSI) for natural heterogeneous wetland habitats. CWSI based on remotely sensed land surface temperature and associated basic meteorological (air temperature and humidity) measurements. CWSI was calculated based on high resolution LST measurements from UAV platform and compare with on ground measurements of soil moisture, CCI, fAPAR and meteorological conditions. Results shows that CWSI properly shows water condition of plants in measured habitats and revels high importance of metrological conditions during data acquisition.

The effect of transition metal substitution for Fe and the structural and magnetic properties of Gd2Fe16Ga0.5TM0.5 (TM=Cr, Mn, Co, Ni, Cu, and Zn) compounds were investigated. Rietveld analysis of X-ray diffraction indicates that all the samples crystallize in the hexagonal Th2Ni17 structure. The lattice parameters: a, c and unit cell volume show TM ionic radii dependence. Both Ga and TM atoms show preferred site occupancy for 12j and 12k sites. The saturation magnetization at maximum room temperature was observed for Co, Ni, and Cu of 69, 73, and 77 emu/g, respectively while minimum value was observed for Zn (62emu/g) doping Gd2Fe16Ga0.5TM0.5. Highest Curie temperature of 590 K was observed for Cu doping which is 15% and 5% and thesehigher than Gd2Fe17 and Gd2Fe16Ga compounds, respectively. The hyperfine parameters viz. hyperfine field and isomer shift, show systematic dependence on the TM atomic number. The observed magnetic and Curie temperature behavior in Gd2Fe16Ga0.5TM0.5 is explained on the basis of Fe(3d)-TM(3d) hybridization. The superior Curie temperature and magnetization value of Co, Ni, and Cu doped Gd2Fe16Ga0.5TM0.5 compounds as compared to pure Gd2Fe17 or Gd2Fe16Ga makes Gd2Fe16Ga0.5TM0.5 a potential candidate for high-temperature industrial magnet applications.

Meixner's historical remark in 1969 "... it can be shown that the concept of entropy in the absence of equilibrium is in fact not only questionable but that it cannot even be defined...." is investigated from today's insight. Several statements --such as the three laws of phenomenological thermodynamics, the embedding theorem and the adiabatical uniqueness-- are used to get rid of non-equilibrium entropy as a primitive concept. In this framework, Clausius inequality of open systems can be derived by use of the defining inequalities which establish the non-equilibrium quantities contact temperature and non-equilibrium molar entropy which allow to describe the interaction between the Schottky system and its controlling equilibrium environment.

A highly dirt resistant paint for building facades without chemicals harmful to nature and environment, is developed which resolves the unattractive disfigurement of building walls caused by dirt. The experimentation is scientifically and statistically planned with the aid of computer programming. It consists of a sequence of phases which include the selection of appropriate raw materials, adopting of Basic Language computer programming to generate a target population of paint formulations. The average PVC percentage is computed using theory and found to be 54.98% for the target population of 543143 paint formulations hence verifies the literature results. Experimentation and statistical analysis are performed to compare the classical conventional agitator with latest lab equipment like Nano mill and it is concluded that Nano mill performs better on the average than conventional agitator in preparation of paint formulations. Hence the sample of paint formulations is prepared on Nano mill and tested in laboratory using advanced available technology for the analysis and comparison of paint properties to determine the best paint formulation. The results are analyzed using Analysis Of Variance Technique (ANOVA) and it is concluded that the paint formulation named “O3” has the highest dirt resistance on the average. The final selected formula O3 is compared with three other competitor paints in market under natural environment for a period of almost one year. A regression model is also constructed to study the effect of environmental factors like time, temperature and humidity on dirt resistance of paints. It is found that O3 formulation is the best environment friendly which performs equally well with one competitor paint and has higher dirt resistance than two other competitor paint formulations containing harmful chemicals. The regression model of dirt resistance on variables including time, temperature and humidity shows that these factors are significantly affecting the dirt resistance of a given paint at 5% level of significance. 95.34% variation in the dirt resistance of a given paint is due to and explained by the given factors. The regression model is useful to predict the average dirt resistance of a given paint with a certain level of confidence. The project exemplifies the work of an applied research from conceptualization to successful commercialization for the paint industry.

In this paper, the effect of Bi₂O₃ doping on the mechanical properties of PbO ceramic pellets was studied. For this purpose, different ratios of Bi2O3/PbO (i.e., xBi2O3–(1-x)PbO, where x is 0, 1, 3, 5, 7 wt%) were fabricated and sintered at 570, 620, and 670°C. Mechanical properties including density, hardness, flexural strength, and sintering of PbO were studied for the aforementioned compositions. Phase compositions, microstructures, and worn surfaces of the composites were characterized by scanning electron microscopy and X-ray diffraction (XRD). The XRD analysis revealed that a solid solution formed in the composite ceramic. The best suited conditions of temperature and doping of Bi₂O₃ for optimal sintering are 620°C and 3 wt%, respectively. The hardness of the 3 wt% Bi2O3–97 wt% PbO ceramic was 717 MPa, which is about four times higher than the hardness of pure PbO; in addition, the strength of the composites was 43 MPa, which is two times higher than that of pure PbO. The integrity of the composites was verified using the lead–bismuth eutectic alloy flushing experiment. Results of this research paper are important for future studies of oxygen control in the lead–bismuth eutectic alloy of lead-cooled fast reactors.

The Gleeble-1500D thermal simulation test machine was used to conduct the isothermal compression test on 21-4N at the strain rate ( ) of 0.01-10s-1, the deformation temperature (T) of 1273-1453K and the maximum deformation is 0.916. The data of the stress-strain ( - )were obtained. Based on the - data, the Johnson-Cook (J-C), modified J-C, Arrhenius and Back-Propagation Artificial Neural Network (BP-ANN) models were established. The accuracy of four models were verified, analyzed and compared. The results show that J-C model has a higher accuracy only under reference deformation conditions. When the deformation condition changes greatly, the accuracy of J-C model is significantly reduced. The coupling effect of T and of modified J-C model is considered, and the prediction accuracy is greatly improved The Arrhenius model introduces Zener-Hollomon (Z) to represent the coupling effect of T and , it has a fairly high prediction accuracy. And it can predict flow stress ( ) accurately at different conditions. The accuracy of BP-ANN model is the highest, but its learning rate is low, the learning and memory are unstable. It has no memory for the weights and thresholds of the completed training. So, there are certain limitations of it in use. Finally, a FEM of the isothermal compression experiment for four models were established, and the distribution of the equivalent stress field, equivalent strain field and temperature field with the deformation degree of 60% were obtained.

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

Objective On the eve of the summer Olympic Games in Tokyo research focus has shifted on the core temperature responses of elite athletes competing in the heat. In the absence of the field data of core temperature during Olympic sailing competition aim of the present study was to identify core temperature response during the Tokyo 2020 Olympic Test Event. Methods Four elite athletes from Olympic sailing (177.5±5.2 cm, 71.1±7.4 kg, body mass index 22.5±1.4 kg/m2, 24.8±3.7 yrs, VO2max 50.6±7.2 mL/min/kg)): 2 males and 2 females participated in the study. Core temperature was recorded using e-Celsius ingestible capsules, heart rate using a heart rate monitor. Ambient conditions in direct sunlight were measured using portable meteo station. Results Core temperature was recorded at water environment via an ingestible capsule in 4 sailors during the training (T), and competition (C), respectively. Ambient conditions in direct sunlight were hot and humid: during training temperature were 30.9°C±1.7°C and relative humidity 81.4%±2.8%, corresponding to a wet-bulb globe temperature of 41°C±4°C and during competition temperature was 31.2°C±2.3°C and relative humidity 87.2%±4.4%, corresponding to a wet-bulb globe temperature of 45.2°C±8.9°C. Core temperature increased during training reaching higher peak values (38.6°C±0.4°C) and during competition (38.9°C±0.4°C). The highest temperature recorded was 39.4°C (C). Conclusion The current study provides unique information into the core temperature parameters under heat stress in elite Olympic sailors during training and race event.

Mount Semeru is one of the most active volcanoes in the Java Island. This article presents the results of observations and detections of volcanic ash cloud after Mt Semeru eruptions on 1 December 2020 at 01:23 AM. Volcanic ash cloud detection was conducted by analyzing thermal infrared (TIR) satellite images acquired by the NOAA-20 and SNPP with MODIS and VIIRS instruments. The TIR instruments have detected the presence of volcanic ash cloud. The results show increasing ash cloud brightness temperature (BT) from 240 to 270 Kelvin (K) several hours after eruptions. Increasing BT indicated the development of volcanic Cumulonimbus (Cb) at lower altitude. Northeast movements of 270 K BT clouds were observed at 06:12 AM. Presences of volcanic Cb and SO₂ were confirmed using IR bands of 12.0-10.8 µm, 11.0-8.5µm and 11.0 µm. This Cb cloud was observed moving northeast directions. The data acquired from the TIR imagery resulted from this study is thought be used in future to support and complement ground-based observations and detections of active volcanoes mainly in Java Island.

The physical environment plays an important role in the transmission of respiratory infections like Covid-19. To find relevant articles on environmental factors influencing respiratory infection outbreaks, we searched Pub med Central on the following topics: 1. Environmental pollution causing coronavirus fatality- 73 results, relevant 1 article, 2. Environmental factors affecting Covid-19, 149 results from which there were 6 relevant articles, 3. Impact of air pollution on Covid-19 fatality, 10 results, relevant 3 articles, 4. Environmental factors affecting respiratory viruses- 10646 results were obtained, 2 relevant articles. We searched Google scholar on environmental factors affecting Covid-19 transmission and found 7 relevant papers. We excluded the duplicates in each of the key words search. Date of search was on 20^th April 2020. All articles included in results were scrutinized and relevance of articles was based on their content that discussed meteorological and physical environment factors in the spread and severity of Covid-19. We have discussed factors like air pollution, smoking, air temperature, humidity and air velocity as contributing factors. If meteorological factors are conducive to spread in a particular area, we need protective measures way before a respiratory infection outbreak occurs. Covid-19 is a lesson learnt the hard way, and we must enable people to practice hygienic practices with limited resources but high level of protection that it provides. Air pollution control can prevent priming of respiratory system which shall further protect from pulmonary infections.

Recently Kawashima has reported that, when wetted with alkanes, several forms of graphite and single-layer graphene exhibit superconductor-like properties above room temperature under ambient pressure [AIP Adv. 2013, 3, 052132; arXiv:1612.05294; arXiv:1801.09376]. Under the assumption that these seemingly unlikely properties arise from the presence of paired electrons brought about by the alkane-wetting, we explored their implications to arrive at a probable mechanism for strong electron-pairing driven by Fermi surface nesting and acoustic phonon. This mechanism explains why alkane-wetting is essential for the graphene systems to become “superconductor-like” above room temperature and why the “T_c” of alkane-wetted pitch-based graphite fibers increases almost linearly from ~363 to ~504 K with increasing the molecular weight of alkane from heptane to hexadecane. It also provides a number of experimentally-verifiable predictions, the confirmation of which will provide a strong support for the superconductivity driven by Fermi surface nesting and acoustic phonon.

When different strain hardening and strain rate sensitive materials are used for scaled model and prototype, the traditional pure geometrical similarity laws of solid mechanics will fail. Although correcting the basic scaling factors of velocity, density and geometry have been developed to compensate for the material distortion in recent non-geometric scaling works, it is difficult to be widely used because of its inherent indirect (depending on the structural strain and strain rate responses) and inexact (having significant prediction errors for prototype) defects. In this paper, a framework of material similarity, based on the new suggested material dimensionless numbers and the ‘Material number vs. strain/strain-rate’ function curves, are further developed, which represents the objective requirement of similarity theory for the basic mechanical properties of materials. It is demonstrated what is similitude materials of solid mechanics and how to use the best similitude materials to overcome the non-scalabilities of materials for identical or different materials. The direct and exact solution of the basic correction factors is further obtained and therefore overcomes the previous inherent indirect and inexact defects radically. Based on the similarity evaluation of different materials of the classical constitutive models, the impacted structures of circular plate and crooked plate with strain hardening and strain rate sensitive materials are verified numerically. The results show the completely different materials can be exact similitude for various structural behaviors (strain, strain rate, stress and displacement) of time and space fields after using the best similitude materials; and the basic correction factors do not depend on the structural strain and strain rate responses. As a contrast, when the non-similitude materials are used, the similarity results are very sensitive to the selection of strain/strain-rate and often leads to failed predictions. In addition, for the material elastic and temperature effects, the proposed method is also discussed to be valid.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

The accurate quantification of $\frac{F{e}^{3+}}{\Sigma Fe}$ ratios for Mössbauer spectroscopic room temperature measurements involves many steps and, when shown in a composite Mössbaur data table, does not allow enough space for more Mössbauer parameters to be presented in the composite table. So a simple formula is derived, (presented as a short communication) which users will find helpful when they have to determine corrected $\frac{F{e}^{3+}}{\Sigma Fe}$ ratios in their room temperature Mössbauer experiments.

We conducted an in-situ crystal structure analysis of ferroselite at non-ambient conditions. The aim is to provide a solid ground to further the understanding of the properties of this material in a broad range of conditions. Ferroselite, marcasite-type FeSe2, was studied under high pressures up to 46 GPa and low temperatures, down to 50 K using single-crystal microdiffraction techniques. High pressure and low temperatures were generated using a diamond anvil cell and a cryostat. We found no evidences of structural instability in the explored P-T space. The deformation of the orthorhombic lattice is slightly anisotropic. As expected, the compressibility of the Se-Se dumbbell, the longer bond in the structure, is larger than that of the Fe-Se bonds. Less obvious is the behavior of the octahedral bonds, the shorter bond is the most compressible determining a small increase in the octahedron distortion with pressure. We also achieved a robust structural analysis of ferroselite at low temperature in the diamond anvil cell. Structural changes upon temperature decrease are small but qualitatively similar to those produced by pressure.

With quick improvement in the field of network, everything becomes online. Remote user authentication is a mechanism in which remote server verify the correctness of user over common or public channel. Remote user authentication can be Single server authentication or Multi server authentication. The disadvantage of single server authentication is that the user needs to recall user id and password for each service, he/she need to utilize, however it can overcome by Multi-server authentication in which user needs to register himself with Registration Center (RC) for the first run through and after that onwards he can utilize each service (which are given by servers, associated with RC) by recollecting only one user id and password. In this paper, we analyze Chen's authentication scheme (based on multi server authentication) and show that this scheme is vulnerable to password guessing attack, replay attack, RC spoofing attack, session key verification attack and perfect forward secrecy attack. In this Paper, we propose a biometric based remote user authentication scheme in multi-server environment. Proposed scheme is more secure and efficient as compared to chen's scheme\cite{23}.

The present work aims to characterize the mechanical behavior of a new composite material for the conservation and development of the vast historical and architectural heritage that is particularly vulnerable to environmental and seismic actions. The new composite consists of natural hydraulic lime (NHL) -based mortar, reinforced by sisal short fibers randomly oriented in the mortar matrix. The NHL-based mortar ensures the chemical-physical compatibility with the original feature of the historical masonry structures (mostly in stone and clay) aiming to pursue both the effectiveness and durability of the intervention. The use of vegetable fibers (i.e. the sisal one) is an exciting challenge for the construction industry since they require a lower degree of industrialization for their processing, and therefore, their costs are also low, as compared to the most common synthetic/metal fibers. Beams of sisal-composite sizing 160x40x40 mm3 with a central notch are tested in three-point bending, aiming to evaluate both their bending strength and fracture energy. Also, tensile tests and compressive tests were performed on the composite samples, while water retention test and slump test were performed on the fresh mix. Finally, the tensile tests on the Sisal strand were carried out to evaluate the tensile strength of both strand and wire. A final comparison with unreinforced mortar specimens shows that the proposed composite ensures great workability and good performances in term of ductility and strength and it can be considered a promising alternative to the classic fiber-reinforcing systems.

The rearing temperature of the immature stages can have a significant impact on the life-history traits and the ability of adult mosquitoes to transmit diseases. This review assessed published evidence of the effects of temperature on the immature stages, life-history traits, insecticide susceptibility, and expression of enzymes in the adult Anopheles mosquito. Original articles published through 31 March 2021 were systematically retrieved from Scopus, Google Scholar, Science Direct, PubMed, ProQuest and Web of Science databases. After applying eligibility criteria, 29 studies were included. The review revealed that immature stages of Anopheles arabiensis were more tolerant (in terms of survival) to a higher temperature than An. funestus and An. quadriannulatus. Higher temperatures resulted in smaller larval size and decreased hatching and pupation time. The development rate and survival of Anopheles stephensi were significantly reduced at a higher temperature than a lower temperature. Increasing temperatures decreased the longevity, body size, length of the gonotrophic cycle and fecundity of Anopheles mosquitoes. Anopheles mosquitoes exposed at 18° or 30 °C had a higher risk of dying compared to those exposed at 25 °C. Increasing temperature also significantly increased NOS expression and decreased insecticide toxicity. Both extreme low and high temperatures affect Anopheles mosquito development and survival. Climate change could have diverse effects on Anopheles mosquitoes. There seems to be inconclusive evidence of the effects of temperature on the development and survival of Anopheles species, and more studies are needed to clarify this relationship.

Satellite-based remote sensing technologies are utilized extensively to investigate urban thermal environments under rapid urban expansion. Current MODIS data is, however, unable to adequately represent the spatially detailed information because of its relatively coarser spatial resolution, while Landsat data can’t explore temporally the refined analysis due to the low temporal resolution. In order to resolve this situation, we used MODIS and Landsat data to generate “Landsat-like” data by using the flexible spatiotemporal data fusion method (FSDAF), and then studied spatiotemporal variation of land surface temperature (LST) and its driving factors. The results showed that 1) The estimated “Landsat-like” data have high precision; 2) By comparing 2013 and 2016 datasets, LST increases ranging from 1.8°C to 4°C were measurable in areas where the impervious surface area (ISA) increased, while LST decreases ranging from -3.52°C to -0.70°C were detected in areas where ISA decreased; 3) LST has a strongly negative relationship with the Normalized Difference Vegetation Index (NDVI), and a strongly positive relationship with Normalized Difference Built Index (NDBI) in summer; and 4) LST is well correlated with Building density (BD), in a complex conic mode, and LST may increase by 0.460°C to 0.786°C when BD increases by 0.1. Our findings can provide information useful for mitigating undesirable thermal conditions and for long-term urban thermal environmental management.

Present work has systematically investigated the evolution of dispersoid and elevated-temperature properties including the strength and creep resistance during the various multi-step heat treatments in Al-Mn-Mg 3004 alloys. Results show that only α-Al(MnFe)Si dispersoid is observed in the studied temperature range (up to 625°C) and it coarsens with increasing temperature to 500°C but dissolves at 625°C. The evolution of elevated-temperature strength and creep resistance is greatly related to the temperature of each step during the multi-step heat treatments. Generally, lower temperature at the first-step heat treatment leads to higher properties while the properties decrease with increasing temperature of last-step heat treatment. Suitable models have been introduced to explain the evolution of strength and the creep threshold stress at elevated-temperature during the various heat treatments.

Increased traffic in combination with growing environmental impacts, have led to accelerated degradation of the built infrastructure. In reinforced concrete structures, the corrosion of steel reinforcement is the predominant cause of deterioration. Thus, over the last years the use of glass fiber reinforced polymer (GFRP) composites as internal reinforcement bars (rebars) for concrete structures was evaluated, and has been proved to be a viable alternative to traditional steel reinforcement mainly due to its tensile strength and non-corrosive nature. However, thus far, the GFRP rebar market is diverse and manufacturers around the world produce GFRP rebar types with different surface enhancement to improve the bond to concrete characteristics. In this study, the bond performance of three dissimilar GFRP rebar types (sand coated, helically grooved and with surface lugs) was evaluated over time in seawater environments, with a focus on the bond strength. Accordingly, specimens were expose to seawater in circulating chambers, at three different temperatures (23 °C, 40 °C and 60 °C) for multiple time periods (60 and 120 days). To evaluate the bond performance, pullout tests were conducted according to ASTM D7913 [1]. The results showed that the bond strength varies with surface enhancement features. However, the bond strength didn’t vary significantly with exposure time and temperature for all three evaluated rebar types.

One challenging problem is the representation of three-dimensional datasets that vary with time. These datasets can be though as a cloud of points that gradually deforms. But point-wise variations lack of information about the overall deformation pattern, and more importantly, about the extreme deformation locations inside the cloud. The present article applies a technique in computational mechanics to derive the strain-rate state of a time-dependent and three-dimensional data distribution, by which one can characterize its main trends of shift. Indeed, the tensorial analysis methodology is able to determine the global deformation rates in the entire dataset. With the use of this technique, one can characterize the significant fluctuations in a reduced multivariate description of an urban system and identify the possible causes of those changes: calculating the strain-rate state of a PCA-based multivariate description of an urban system, we are able to describe the clustering and divergence patterns between the districts of the city and to characterize the temporal rate in which those variations happen.

Nowadays industrial dryers are used instead of traditional methods for drying. In designing dryers suitable for controlling the process of drying and reaching a high quality product, it is necessary to predict the instantaneous moisture loss during drying. For this purpose, ten mathematical-experimental models with a neural network model based on the kinetic data of pistachio drying are studied. The data obtained from the cabinet dryer will be evaluated at four temperatures of inlet air and different air velocities. The pistachio seeds will be placed in a thin layer on an aluminum sheet on a drying tray and weighed by a scale attached to the computer at different times. In the neural network, data are divided into three parts: educational (60%), validation (20%) and test (20%). Finally, the best mathematical-experimental model using genetic algorithm and the best neural network structure for predicting instantaneous moisture are selected based on the least squared error and the highest correlation coefficient.

Depending on human body conditions and environmental conditions, it is sometimes difficult to conduct subject experiments. In such cases, it is effective to use a thermal manikin. There are few studies that investigate the effect of the non-uniform and asymmetric outdoor thermal environment on the mean skin temperature. The purpose of this study is to clarify the influence of the non-uniform and asymmetric thermal radiation of short-wavelength solar radiation in an outdoor environment on the calculation of the mean skin temperature. The skin temperature of the front of the coronal surface, which was facing the sun and where the body received direct short-wavelength solar radiation, and the skin temperature of the rear of the coronal surface, which was in the shadow and did not receive direct short-wavelength solar radiation were respectively measured. The feet, upper arm, forearm, hand and lower leg, which are susceptible to short-wavelength solar radiation in a standing posture, had a noticeable difference in skin temperature between sites in the sun and in shade. The mean skin temperature of sites facing the sun was significantly higher than the mean skin temperature of those in the shade.

A severe flash flood hit Luwu, Sulawesi, Indonesia, on 13 July 2020. This flood was preceded by persistent heavy rainfall from 11 to 13 July 2020. In this study, we explore both the physical and dynamical processes that caused the heavy rainfall using a convection-permitting model with 1-km resolution. The heavy rainfall was modulated by the development of a pair of Mesoscale Convective Complexes (MCCs) during the night. The pair of MCCs was triggered by an anti-cyclonic vorticity anomaly over the Makassar Strait and was maintained by the warm front passing between the sea and land over central Sulawesi. This front was characterized by moist-warm and cold-dry low-level air, which may have helped to extend the lifetime of the MCCs. The northwestward propagation of the MCCs was due to the interaction between predominantly southeasterly monsoon and sea surface temperature anomalies.

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

Different process parameters can alter the temperature during machining. Consequently, selecting process parameters that lead to a desirable cutting temperature would help to increase the tool life, decrease the tensile residual stress, and controls the microstructure evolution of the workpiece. An inverse computational methodology is proposed to design the process parameters for specific cutting temperature. A physics-based analytical model is used to predict the temperature induced by cutting forces. To calculate the temperature induced by the deformation in the shear zone, a moving point heat source approach is used. The shear deformation and chip formation model is implemented to calculate machining forces as functions of process parameters, material properties, and etc. The proposed model uses the analytical model to predict the cutting temperatures and applies a variance-based recursive method to guide the inverse analysis. In order to achieve the cutting process parameters, an iterative gradient search is used to adaptively approach the specific temperature by the optimization of process parameters such that an inverse reasoning can be achieved. Experimental data are used to illustrate the implementation and validate the viability of the computational methodology.

The hybrid personal cooling system (HPCS) consisted of ventilation fans and phase change materials (PCMs) covered with insulation pads is a promising wearable cooling system to mitigate heat strain and heat-related illnesses of occupational workers with heavy labor in hot environments. Effects of clothing characteristics (e.g., thermal resistance of insulation pads, latent heat and melting temperature of PCMs) on the thermal performance of the HPCS have been investigated in detail in our previous study. Apart from the aforementioned factors, environmental conditions, i.e., environmental temperature and relative humidity, also significantly affect the thermal performance of the HPCS. In this paper, a numerical parametric study was performed to investigate the effects of the environmental temperature and relative humidity (RH) on the thermal management of the HPCS. Five levels of air temperature under environmental RH=50% were chosen (i.e., 32, 34, 36, 38 and 40 ºC) to study the impact of environmental temperature on the HPCS’s cooling performance. In addition, four levels of environmental RH at ambient temperatures of 36 and 40 ºC were selected (i.e., 30, 50, 70 and 90%) to examine the effect of RH on cooling performance of the HPCS. Results show that high environmental temperatures could accelerate the PCM melting process and thereby weaken the cooling performance of HPCS. In the moderately hot environment (36 °C), the HPCS presented good cooling performance with the maximum core temperature at around 37.5 °C during excise when the ambient RH≤70%, whereas good cooling performance could be only seen under RH≤50% in the extremely hot environment (40 °C). Thus, it may be concluded that the maximum environmental RH for the HPCS exhibiting good cooling performance decreases with the increase in the environmental temperature.

Trailing the modern ideas of sociophysics, a minimalistic thermodynamic model of society is proposed, which consists of three social ingredients: people, economy, and entropy. Employing the universal van der Waals equation of state, many important relationships are discovered, including laws of econophysics. A paramount finding is that the Second Law of thermodynamics governs irreversible social evolution, revealing the power of social liberty and economic freedom.

Several methods have been tried to estimate air temperature using satellite imagery. In this paper, the results of two machine learning algorithms, Support Vector Machine and Random Forest, are compared with Multivariate Linear Regression, TVX and Ordinary kriging. Several geographic, remote sensing and time variables are used as predictors. The validation is carried out using four different statistics on a daily basis allowing the use of ANOVA to compare the results. The main conclusion is that Random Forest with residual kriging produces the best results (R$^2$=0.612 $\pm$ 0.019, NSE=0.578 $\pm$ 0.025, RMSE=1.068 $\pm$ 0.027, PBIAS=-0.172 $\pm$ 0.046), whereas TVX produces the least accurate results. The environmental conditions in the study area are not really suited to TVX, moreover this method only takes into account satellite data. On the other hand, regression methods (Support Vector Machine, Random Forest and Multivariate Linear Regression) use several parameters that are easily calculated from a Digital Elevation Model, adding very little difficulty to the use of satellite data alone. The most important variables in the Random Forest Model were satellite temperature, potential irradiation and cdayt, a cosine transformation of the julian day.

The work focused on the development of high-temperature electrical insulation coatings for film photovoltaics. The idea was into replacing the electroconductive metal dispersed phase in siloxane high-temperature coating to ceramic particles with phonon thermal conductivity. The slurry of industrial composition based on polysiloxane lacquer and thermally conductive paste containing zinc oxide was centrifuged to obtain a thin, optically transparent coating with the destruction temperature of over 600 °C. Topology, electrical properties, and thermal conductivity of the resulting film were investigated. The mathematical model of thermal processes in films in the course of heating was figured out. Quantitatively the relation of thermal conductivities of a control sample and a sample with a heat-conducting filler was established. The effectiveness of using this technology is shown.

Protein is the proteios building block of life. Evolutionarily, its sequence is not as conserved as its structure, making it more reasonable for protein structure, instead of protein sequence, to be the descriptor of protein function. Yet, in the National Center for Biotechnology Information (NCBI) database, the number of experimentally identified protein sequences is in great excess of that of experimentally determined protein structures inside the almost-half-a-century old Protein Data Bank (PDB). For instance, GPR151 is an proton-sensing G-protein coupled receptor (GPCR) originally identified as homologous to galanin receptors. As of March 19, 2020, GPR151’s structure has not been experimentally determined and deposited in PDB yet. Thus, an ab initio modelling approach was employed here to build a three-dimensional structure of GPR151. Overall, the ab initio GPR151 model presented herein constitutes the first structural hypothesis of GPR151 to be experimentally tested in future with previously published, currently ongoing and future GPR151 studies.

This study presents a novel approach for the early detection of developing thunderstorms. To date, methods for the detection of developing thunderstorms usually rely on accurate atmospheric motion vectors (AMVs) for the estimation of cooling rate of convective clouds, which corresponds to the updraft strength of the cloud objects. In this study we present a method for the estimation of the updraft strength that does not rely on AMVs. The updraft strength is derived directly from the satellite observations in the SEVIRI water vapor channels. For this purpose the absolute value of the vector product of two vectors derived from the observed radiances emitted by the water vapor channels in 2 subsequent satellite images is calculated. The x and y components of the vectors consists of the temporal change of the spatial brightness temperature gradients in x- and y-direction, the z component consists of the temporal variation of the brightness temperature at pixel level. The absolute value of the vector product is referred to as normalized updraft strength (NUS). The performance of the method has been investigated for 2 summer periods in 2016 and 2017 by validation with lightning data. Values of the Critical Success Index (CSI) of about 66 % for the 2016 period and 62 % for the 2017 period demonstrate the good performance of the method. The POD values for the experiments with the highest CSI values are 90.3 for 2016 period and 87.6 for the 2017 period, respectively The corresponding FAR values are 28.2% (2016) and 32.5 % (2017), respectively. In summary, the method has the potential to reduce the forecast lead time significantly, and can be quite useful in regions without a well maintained radar network.

The research carried out concerned the laboratory assessment of the applicability of the Crop Water Stress Index (CWSI) as a practical tool for assessing the risk of desiccation for selected wetland habitats: transition mires and quaking bogs as well as alkaline fens. The analysis was carried out on 3 soil samples with a vegetation cover (with the dimensions of 40×40×30 cm) collected during the full vegetation season for each mentioned habitat, with a characteristic species composition. Experimental research was carried out between 17^th May 2018 and 19^th June 2018. Thermal, RGB and multispectral images, chlorophyll content, volumetric soil moisture, air temperature and relative humidity measurements were taken for each sample every two days. The obtained results clearly indicate the dependence between CWSI and plant condition parameters in the first phase of desiccation. At the same time, as a result of the observations taken, thresholds have been set, indicating different desiccation phases.

We report the results of an analysis of the functional capabilities of the KTP crystal and its isomorphs for nonlinear-optical frequency conversion of all types of interaction in the transparency range of the crystal. The possibility of implementing angle-, wavelength- (frequency-) and temperature-noncritical phase matching is shown.