District heating networks have become widespread due to their ability to distribute thermal energy efficiently, which leads to reduced carbon emissions and improved air quality. The characteristics of these networks vary remarkably depending on the urban layout and system amplitude. Moreover, extensive data about the energy distribution and thermal capacity of different areas are seldom available. Design, optimization and control of these systems are enabled by the availability of fast and scalable models of district heating networks. This work addresses this issue by proposing a novel method to develop a scale-free model of large-scale district heating networks. Starting from coarse data available at the main substations, a physics-based model of the system aggregated regions is developed by identifying the heat capacity and heat loss coefficients. The model validation on the network of Västerås, Sweden, shows compatibility with literature data and can therefore be exploited for system design, optimization and control-oriented applications. In particular, the possibility to estimate the heat storage potential of network regions allows new smart management strategies to be investigated.

The widely adopted temperature for solid solution heat treatment (ST) for the conventionally fabricated Inconel 718 is 1100 °C for a hold time of 1 h or less. This ST scheme is however not enough to dissolve Laves and annihilate dislocations completely in samples fabricated with Laser metal powder bed fusion (L-PBF) additive manufacturing (AM)-Inconel 718. In spite this, the highest hardness obtained after aging for ST temperatures (970 - 1250 °C) is at 1100 °C/1h [1]. The unreleased residual stresses in the retained lattice defects are potentially affecting other properties of the material. Hence, this work aims to investigate if a longer hold time of ST at 1100 °C will lead to complete recrystallization while maintaining the strength after aging or not. For this study, L-PBF-Inconel 718 samples were ST at 1100 °C at various hold times (1, 3, 6, 9, 16 or 24 h) and aged to study the effects on microstructure and hardness. In addition, a sample was directly aged to study the effects of bypassing ST. The samples (ST and aged) gain hardness by 43 – 49 %, depending on hold time. A high density of annealing twins evolved during 3 h of ST and the quantity only slightly varies for longer ST.

The management of carbapenem-resistant infections is often based on colistin, tigecycline, aminoglycosides and their combinations. However, in a recent systematic review we found that Gram-negative bacteria (GNB) co-resistant to carbapanems, aminoglycosides, colistin and tigecycline (CACT-resistant) are increasingly being reported worldwide. Clinical data to guide the treatment of CACT-resistant GNB are scarce and based exclusively on few case reports and small case series but seem to indicate that appropriate (in vitro active) antimicrobial regimens, including newer antibiotics and synergistic combinations, may be associated with lower mortality. In this review we consolidate the available literature to inform clinicians dealing with CACT-resistant GNB about treatment options by considering the mechanisms of resistance to carbapenems. In combination with rapid diagnostic methods that allow fast detection of carbapenemase production, the approach proposed in this review may guide a timely and targeted treatment of patients with infections by CACT-resistant GNB. Specifically, we focus on the three most problematic species, namely Klebsiella pneumoniae, Pseudomonas aeruginosa and Acinetobacter baumannii. Several treatment options are currently available for CACT-resistant K. pneumonia. Newer β-lactam-β-lactamase combinations, including the combination of ceftazidime/avibactam with aztreonam against metallo-β-lactamase-producing isolates, appear to be more effective compared to combinations of older agents. Options for P. aeruginosa (especially metallo-β-lactamase-producing strains) and A. baumannii remain limited. Synergistic combination of older agents (e.g. colistin- or fosfomycin-based synergistic combinations) may represent a last resort option but their use against CACT-resistant GNB requires further study.

Chronic heat stress (HS), aggravated by global warming, reduces the production efficiency of the buffalo dairy industry. Here, we conducted a proteomic analysis to investigate the adaptation strategies used by buffalo in response to heat stress. Seventeen differentially abundant proteins with known functions were detected using label-free quantification (LFQ), and five of these differentially expressed proteins were validated with parallel reaction monitoring (PRM). These five proteins were associated with various aspects of heat stress, including decreased heat production, increased blood oxygen delivery, and enhanced natural disease resistance. Lipase (LPL), glutathione peroxidase 3 (GPX3), cathelicidin-2 (CATHL2, LL-37), ceruloplasmin (CP), and hemoglobin subunit alpha 1 (HBA1) were shown to play cooperative roles in the tolerance of chronic HS in dairy buffalo. We found that high levels of HBA1 increased blood oxygen transport capacity. Our results increase our understanding of the adaptation of dairy buffalo to chronic heat stress.

Background: Breast cancer is the leading cause of cancer mortality and morbidity among Indonesian women. Identification of biological pathways leading into therapeutic resistance through in vitro model is an important step to develop alternative effective therapy in breast cancer. Loss of PTEN expression has been associated with resistance to chemotherapy by involving PI3K/PTEN- dependent apoptosis pathway. We conducted in vitro experiment to investigate the association of hsa-miR-21 and PTEN expression in Doxorubicin-resistant MCF-7 cell line. Methods: Parental MCF-7 cells were periodically incubated with Doxorubicin to obtain specific Dox-resistant variant determined by IC50 using MTT assay. PTEN protein expression was analyzed using immunocytochemistry. Expression of mature has-miR-21 was measured using qRT-PCR. Results: The IC50 of Doxorubicin in parental MCF-7 and Doxorubicin-resistant MCF-7 cells (MCF-7/Dox) was 0.68 and 5.78 µg/ml, respectively. Hsa-miR-21 was significantly overexpressed in MCF-7/Dox cells compared to parental MCF cells (7.94 fold changes). Conclusion: PTEN and hsa-miR-21 expression levels were negatively correlated in Doxorubicin resistant-MCF cells. Further study to confirm the causal relationship of miR-21 overexpression and PTEN downregulation in MCF-7/Dox is required.

Energy system optimization models (ESOM) are widely used to inform about energy transition strategies. The heterogeneity of consumers, especially in the heat sector, is rarely considered in these model types. Integrating consumer heterogeneity and behavioral factors into ESOMs may generate new insights for energy policy. In this study a literature review was conducted, identifying empirical data on consumer behavior for adopting residential heating systems. This data was integrated into an ESOM for the German heat sector, combining established methods for integrating consumer heterogeneity and a novel approach for calculating indirect costs, representing behavioral factors. The incorporation of consumer choice leads to a higher diversity in technology market shares in a business as usual and an ambitious measures scenario. Especially, the future role of log wood technologies in the private household sector may have been underestimated in previous studies and should be discussed, when designing policies. Still, these findings need to be handled with care, since the empirical data basis and the methodological basis is limited.

The aim of this study was to establish the blood glucose response to different cooking methods of pasta. Participants consumed three identical meals in a random order that were freshly cooked (hot), cooled and reheated. Blood glucose concentrations were assessed before, and every 15 minutes after ingestion of each meal for 120 minutes. There was a significant interaction between temperature and time (F_{(8.46-372.34)} = 2.75, p = 0.005), with the reheated (90 minutes) condition returning to baseline faster than both cold (120 minutes) and hot conditions. Blood glucose AUC was significantly lower in the reheated (703 ± 56 mmol L^-1 min^-1) compared with the hot condition (735 ± 77 mmol L^-1 min^-1, t(92) = -3.36, pbonferroni = 0.003), with no significant difference with the cold condition (722 ± 62 mmol L^-1 min^-1). To our knowledge, the current study is the first to show that reheating pasta causes changes in post-prandial glucose response, with a quicker return to fasting levels in both the reheated and cooled conditions compared with the hot condition. The mechanisms behind the changes in post-prandial blood glucose seen in this study are most likely related to changes in starch structure and how these changes influence glycaemic response.

Botanical recycled concrete, or concrete bonded with wood, is formed by heat pressing the mixture of concrete and wooden waste. Botanical recycled concrete is a relatively new material and the relationship between production condition and its real-world performance is not clear yet. This experimental study investigated the influence of several production condition factors on the density and bending strength of botanical recycled concrete. As a result, temperature and mass ratio of concrete powder to wood flour presented significant effects on the density of this botanical recycled concrete. The increase in production temperature resulted in a remarkable increment in density and bending strength. This is probably due to increased wood flowability and accelerated compaction and bonding formation. The fineness of wood flour had a significant effect on improving bending strength. This is attributed to a larger contact surface between the wood substance and concrete particles.

Heat stress affects the granulosa cells (GCs) and ovarian follicular microenvironment, causing poor oocyte developmental competence and fertility. This study aimed to investigate the physical responses and global transcriptomic changes in bovine GCs to acute heat stress (43 ℃ for 2 h) in-vitro and gave essential insights into the general interaction at cell–stress nexus. Heat-stressed GCs exhibited transient proliferation senescence, resumed proliferation at 48 h post-stress. While post-stress immediate culture-media change had a relatively positive effect on proliferation resumption. Increased accumulation of reactive oxygen species and apoptosis was observed in heat stress group. In spite of the upregulation of pro-apoptotic and caspase executioner genes, antioxidants and anti-apoptotic genes were also upregulated in heat-stressed GCs. Progesterone and Estrogen hormones along with steroidogenic genes expression, declined significantly, in spite of the upregulation of genes involved in cholesterol synthesis. Out of 12385 differentially expressed genes (DEGs), 330 significant DEGs (75 upregulated, 225 downregulated) were subjected to KEGG functional pathway annotation, gene ontology enrichment, and STRING network analyses. Based on the manual query of DEGs, pathway and enrichment analyses, a vast interplay observed among all major signaling pathways strongly evidence the repression of cellular transcriptional and proliferation activity, averting the effects of heat stress through remodeling of cellular structural proteins and energetic-homeostasis. This study presents detailed responses of acute heat-stressed GCs at physical, transcriptional, and pathway levels and presents interesting insights into future studies regarding GCs adaptation and their interaction with oocyte and reproductive system at ovarian level.

The impact of snow darkening by deposition of light absorbing aerosols (LAAs) on snow cover over the Himalaya-Tibetan-Plateau (HTP) and influence on the Asian monsoon are investigated using the NASA Goddard Earth Observing System Model Version 5 (GEOS-5). We find that during April-May-June, deposition of LAAs on snow leads to a reduction in surface albedo, initiating a sequence of feedback processes, starting with increased surface solar radiation, rapid snowmelt in HTP and warming of the surface and upper troposphere, followed by enhanced low-level southwesterlies and increased dust loading over the Himalayas-Indo-Gangetic Plain. The warming is amplified by increased dust aerosol heating, and subsequently amplified by latent heating from enhanced precipitation over the Himalaya foothills and northern India, via the Elevated Heat Pump (EHP) effect during June-July-August. The reduced snow cover in the HTP anchors the enhanced heating over the Tibetan Plateau and its southern slopes, in conjunction with an enhancement of the Tibetan Anticyclone, and the development of an anomalous Rossby wavetrain over East Asia, leading to weakening of the subtropical westerly jet, and northward displacement and intensification of the Mei-Yu rainbelt. Our results suggest that atmosphere-land heating by LAAs, particularly desert dust play a fundamental role in physical processes underpinning the snow-monsoon relationship proposed by Blandford more than a century ago.

Fever remains an integral part of the acute clinical diseases management, esp. viral, for which effective therapeutics remain desired. However, the presence of often confusing fever reduction recommendations for COVID-19 in the public domain during the pandemic, as late as 28 April 2021, seems to suggest the reduction of any ‘uncomfortable’ fever ranging from 37.8 - 39oC, as opposed to WHO fever reduction guidelines (≥39oC), urgently need attention. The confusion could percolate down into different agencies who look up to these agencies for guidance in framing their own, denying the benefits of fever to populations, and effectively undo whatever successive WHO’s guidelines have achieved in the last two decades. The existence of conflicting guidelines in public domains which are open to interpretations has consequences to public health and the healthcare infrastructure, on implementation. For controlling acute infectious diseases, esp. viral, the fever remains the most important enabler. Historically, our chief obstacles to harnessing the benefits of fever in acute clinical diseases with limited therapeutics had been: a) widespread myths about ‘fevers’ arising from a general misunderstanding of basic facts; b) presence of confusing guidelines by different agencies which are open to alternate interpretation. The article attempts to briefly indicate the benefits of fever in disease resolution, dispel myths, underline vagueness in illustrative national guidelines and the need to align them with evidence-based WHO guidelines, as it has the potential to perpetuate myths/confusion in masses leading to adverse impact on disease management – more morbidity and mortality from diseases including COVID-19.

Necrotizing pneumonia due to Methicillin-Resistant Staphylococcus Aureus (MRSA) is devastating and difficult to treat in preterm infants. We report a case of severe MRSA necrotizing pneumonia in a preterm infant. As an add-on rescue therapy to vancomycin, linezolid rapidly cured this case after the failure of vancomycin plus rifampicin. This rapid cure suggests that adjunctive rather than rescue linezolid may be considered in such cases.

The hygrothermal transfer is very important for the design of a building envelope for thermal comfort and economic and energy analysis of the building envelope. The applications of various materials in building envelope have been studied extensively. The study presents several models for the hygrothermal transfer for various building walls. Several energy and mass conservation equations with different boundary conditions and input considerations were presented in this paper for concrete, bricks and wooden walls. The effect of hysteresis was ignored in developing most model equations, while few considered flow pattern of fluid through the wall surfaces. Due to the flexibility of Luikov models, it formed the basis for modelling the coupled heat and mass transfer for porous material independent of hygroscopic nature with different boundary conditions defined according to the geometry and orientations. The influence of type of wall, orientation, thickness, the density of the material and climatic variations on the temperature and moisture evolutions within the building materials was more pronounced. Literature, presenting imaging models using imagery software like COMSOL multi-physics, CFD etc. were scarce considering that microscopic imagery is now deployed to measure the heat and moisture evolution in materials. Future models should include shrinkage or expansion influence on the fibrous material like wood due to their behaviour under environmental condition.

Surface urban heat island (SUHI) depicts the deteriorating thermal environment in high-density cities and local climate zone (LCZ) classification provides a universal protocol for SUHI identification. In this study, taking the central urbanized area of Guangzhou in the humid subtropical region of China as the study area, the maps or images of LCZ, land surface temperature (LST), SUHI and urban design factors were achieved by using Landsat satellite data, GIS database and a series of retrieval and classification algorithms, and the urban design factors influencing SUHI were investigated based on 625 samples of LCZs. The results show that in the summer daytime under the clear sky condition, the LST varied greatly from 26 °C to 40 °C and the SUHI changed in a wide range of -6 °C to 8 °C in the LCZs of the study area. Seven and five urban design factors influencing the summer daytime SUHI were identified for the two dominant LCZ of LCZs 1-5 (LCZ 1 to LCZ 5) and the mixed LCZ (containing at least three types of LCZs), respectively. The summer daytime SUHI prediction models were obtained by using the step-wise multiple linear regression, with the performance of R2 of 0.697, RMSE of 1.21 °C, and the d value of 0.81 for the model of LCZs 1-5, and the values of 0.666, 1.66 °C, and 0.76 for the model of the mixed LCZ, indicating that the models can predict the changes of SUHI with LCZs to a large and satisfactory extent. This study presents a methodology to efficiently achieve a large sample of SUHI and urban design factors of LCZs in the largely urbanized cities, and provides information beneficial to the urban designs and regenerations in the humid subtropical region.

Extracellular vesicles (EV) released by tumor cells are a major aspect of the resistance-associated secretory phenotype (RASP), by which immune evasion can be established. Heat shock proteins (HSPs) are an evolutionarily conserved family of molecular chaperones, which stabilize proteins, minimize protein misfolding and aggregation within the cell, besides facilitating protein translocation, refolding and degradation. (i) Releases of extracellular HSPs (ex-HSP) and EV-associated HSPs (EV-HSP) are essential in RASP, by which molecular cotransfer of HSPs with oncogenic factors into recipient cells can promote cancer progression and resistance against stress such as hypoxia, radiation, chemicals, and immune system. (ii) RASP of tumor cells can eject anticancer drugs, molecularly targeted therapeutics, and immune checkpoint inhibitors with EVs. (iii) Cytotoxic lipids can be also released from tumor cells as RASP. Nevertheless, ex-HSP and EV-HSP can play immunostimulatory and immunosuppressive roles by binding to receptors such as LRP1/CD91/A2MR, scavenger receptors, and toll-like receptors expressed on recipient cells. Liquid biopsy of HSPs in body fluids may be useful in diagnosis, prognosis, and treatment in cancer. Regarding HSP90-targeted therapeutics, we summarize the pros, cons, and problem solutions in this review. Although production of HSPs are canonically induced by heat shock factor 1 (HSF1) and hypoxia-inducible factor 1 (HIF-1), recent studies discovered that production of HSPs is also regulated by matrix metalloproteinase 3 (MMP3) and heterochromatin protein 1 (HP1) and production of cochaperone CDC37 is reciprocally regulated by myeloid zinc finger 1 (MZF1) and SCAN-D1.

The objective of this study was to evaluate biomarkers of heat stress (HS) from automatic milking system (AMS), the relationships between measurements of temperature-humidity index (THI) and reticulorumen ph and temperature and some automatic milking systems parameters in dairy cows (rumination time (RT), milk traits, body weight (BW) and consumption of concentrate (CC)) during summer period. The experiment was carried out on a dairy farm at 54.9587408, 23.784146. Lithuanian Black and White dairy cows (n=365) were selected. The cows were milked with Lely Astronaut® A3 milking robots with free traffic. The rations were calculated to meet physiological requirements of the animals. Daily milk yield, rumination time, body weight, milk fat and protein ratio were collected from the Lely T4C management program for analysis. The pH and temperature of the contents of cow reticulorumen were measured using specific smaX-tec boluses manufactured for animal care. The daily humidity and air temperature in the farm zone were obtained from the adjacent weather station (2 km away). According this study during HS, the higher THI had positive correlation with ML, which show tendencies to increase risk of mastitis, and decrease CC, RT, BW, MY, reticulorumen ph and F/P. Some biomarkers of HS can be milk yield, milk lactose, somatic cell count, concentrate conception, rumination time, body weight, reticulorumen ph and milk fat – protein ratio. We can recommend to monitoring these parameters in the herd management program to identify possibility of heat stress.

Cloth wearing seems so natural that everyone is self-deemed knowledgeable and has some expert opinions about it. However to clearly explain the physics involved, and hence to make predictions for clothing design or selection, turns out as demonstrated below to be quite challenging even for experts. Cloth is a multiphased, porous and anisotropic material system and usually in multilayers. Unlike ordinary engineering heat transfer problems, the human body acts as an internal heat source in a clothing situation, thus forming a temperature gradient between body and ambient, and the sign of this gradient often changes as the ambient temperature varies. Our body also perspires and the sweat evaporates, an effective body cooling process via phase change. To bring all the variables into analysis quickly escalates into a formidable task. This work attempts to unravel the problem from a physics perspective, focusing on several rarely noticed yet critically important mechanisms involved so as to offer a clear and accurate depiction of the principles in clothing thermal comfort.

Drying food involves complex physical atmospheric mechanisms with non-linear relations from the air-food interactions and those relations are strongly dependent on the moisture contents and the type of food. Such dependence makes it complex to design suitable dryers dedicated to a single drying process. To streamline the design of a novel compact food-drying machine, a heat pump dryer component design optimization algorithm was developed as a subprogram of a Computer Aided Engineering tool. The algorithm requires inputting food and air properties, the volume of the drying container and the technical specifications of the heat-pump off-the shelf components. The heat required to dehumidify the food supplied by the heat exchange process from condenser to evaporator, and the compressor’s requirements (refrigerant mass flow rate and operating pressures) are then calculated. Compressors can then be selected based in the volume and type of food to be dried. The algorithm is shown via a flow chart to guide the user through 3 different stages: Changes in drying air properties, Heat flow within dryer and Product moisture content. Example results of how different compressors are selected for different type of produces and quantities (Agaricus Blazei mushroom with 3 different moisture contents or fish from Thunnini tribe) conclude this article.

The hybrid personal cooling system (HPCS) consisted of ventilation fans and phase change materials (PCMs) covered with insulation pads is a promising wearable cooling system to mitigate heat strain and heat-related illnesses of occupational workers with heavy labor in hot environments. Effects of clothing characteristics (e.g., thermal resistance of insulation pads, latent heat and melting temperature of PCMs) on the thermal performance of the HPCS have been investigated in detail in our previous study. Apart from the aforementioned factors, environmental conditions, i.e., environmental temperature and relative humidity, also significantly affect the thermal performance of the HPCS. In this paper, a numerical parametric study was performed to investigate the effects of the environmental temperature and relative humidity (RH) on the thermal management of the HPCS. Five levels of air temperature under environmental RH=50% were chosen (i.e., 32, 34, 36, 38 and 40 ºC) to study the impact of environmental temperature on the HPCS’s cooling performance. In addition, four levels of environmental RH at ambient temperatures of 36 and 40 ºC were selected (i.e., 30, 50, 70 and 90%) to examine the effect of RH on cooling performance of the HPCS. Results show that high environmental temperatures could accelerate the PCM melting process and thereby weaken the cooling performance of HPCS. In the moderately hot environment (36 °C), the HPCS presented good cooling performance with the maximum core temperature at around 37.5 °C during excise when the ambient RH≤70%, whereas good cooling performance could be only seen under RH≤50% in the extremely hot environment (40 °C). Thus, it may be concluded that the maximum environmental RH for the HPCS exhibiting good cooling performance decreases with the increase in the environmental temperature.

The theoretical limits of water sorbate based chemical sorption heat storage are investigated in this study. First, a classification of \textit{thermochemical heat storage} is proposed based on bonding typology. Then, thermodynamics of chemical solid/gas sorption is introduced. The analysis of the reaction enthalpy from the literature indicates that this value is only slightly varying for one mole of water. Using this observation, and with the help of thermodynamical considerations, it is possible to derive conclusions on energy efficiency of closed and open heat storage systems. Whatever the salt, the main results are 1) the energy required for evaporation of water is, at least, 65% of the available energy of reaction and 2) the maximum theoretical energy efficiency of the system is about 1.8.

Photosynthesis is a pivotal process that determines the synthesis of carbohydrates required for sustaining growth under normal or stress situation. Stress exposure reduces the photosynthetic potential owing to the excess synthesis of reactive oxygen species that disturb the proper functioning of photosynthetic apparatus. This decreased photosynthesis is associated with disturbances in carbohydrate metabolism resulting in reduced growth under stress. We evaluated the importance of melatonin in reducing heat stress-induced severity in wheat plants (Triticum aestivum L.). The plants were subjected to 25 ˚C (optimum temperature) or 40 ˚C (heat stress) for 15 days at 6 hours time duration and then developed the plants for 30 days. Heat stress led to oxidative stress with increased production of TBARS and H2O2 content and reduced accrual of total soluble sugars, starch and carbohydrate metabolism enzymes which are reflected in reduced photosynthesis. Application of melatonin not only reduced oxidative stress through lowering TBARS and H2O2 content, through augmenting the activity of antioxidative enzymes but also increased the photosynthesis in plant and carbohydrate metabolism that is needed to provide energy and carbon skeleton to the developing plant under stress. However, the increase in these parameters with melatonin was mediated via hydrogen sulfide (H2S), as the inhibition of H2S by hypotaurine (HT; H2S inhibitor) reversed the ameliorative effect of melatonin. This suggests a crosstalk of melatonin and H2S in protecting heat stress-induced photosynthetic inhibition via regulation of carbohydrate metabolism.

Resistant cancer often shows a particular secretory trait such as heat shock proteins (HSPs) and extracellular vesicles (EVs), including exosomes and oncosomes surrounded by lipid bilayers. Lipoproteins are biochemical assemblies that transport hydrophobic lipid (a.k.a. fat) molecules in body fluid and are composed of a single-layer phospholipid and cholesterol outer shell, lipids molecules within the particles, and apolipoproteins embedded in the membrane. However, lipoprotein storage and secretion by cancer cells have not well-investigated yet. We found lipoproteins were stored and abundantly secreted by neuroendocrine, castration-resistant prostate cancer (NEPC / CRPC) cells but barely secreted by colon cancer cells and oral squamous cell carcinoma (OSCC) cells. In addition, large EVs (approx. 300 nm diameter) and potential oncosomes were released by CRPC and OSCC cells. Proteomics revealed that CRPC cells secreted EVs enriched with tetraspanins and extracellular matrices which were reduced upon heat shock stress and alternatively lipoproteins and HSPs were secreted upon stress. Heat shock stress triggered secretion of lipoprotein-EV complexes that contained apolipoprotein A, B, C and E. These data suggested that vesicular assembly composed of EVs and lipoproteins enriched with cholesterols and phospholipids may be stored in resistant cancer cells but released upon cell stress that is increased in cancer therapies.

Computational methods are essential to support and advance nuclear technologies due to the hazards of handling and analysing highly radioactive materials such as spent nuclear fuel (SNF). However, many such methods, including those thatcan predict SNF compositions and decay heat parameters, require expensive, proprietary software, alongside significant programming experience and computational power for utilisation, severely limiting availability of data and hampering research throughput. Although some datasets are available, many are incomplete or only cover certain fuel systems for older reactor types. Research investigating new methods for SNF recycling, for example, requires compositional and decay heat data for fuel systems not covered by extant data, though analogous source data may be available. With this in mind, we have developed a simple, accessible, and flexible method for extrapolation of isotopic, elemental, and decayheat compositions for SNF at discharge and following decay storage before recycling, based on an extant dataset. This semi-empirical method uses physical and mathematical first principles and can be performed using software accessible to all researchers. This provides outputs accurate to within 1% of reference values interpolated within the range of available data for isotopic compositions, with sensible extrapolations at higher burnups beyond those reported, withoverall elemental outputs accurate to within 0.1%of expected totals. In this publication, we present the developmental methodology, some sample data, the present limitations, and options for future development and expansion of functionality.

Average of 41,900 patients are diagnosed annually with staphylococcus bacterial infection in California, 24,089 patients have Methicillin-resistant Staphylococcus Aureus (MRSA) and 17,810 patients have Methicillin-Sensitive Staphylococcus (MSSA). This paper demonstrates that there is a difference in mortality rate due to staphylococcus infection between males and females (P-value<0.05, CI 95%). Male patient diagnosed with S. aureus has 1.3 chance of mortality incidence than female patient. In addition, MRSA infection rate is 1.4 times MSSA infection (P-value<0.05, CI 95%), but the gap of infection is decreasing; however, mortality of both infections combined are more than threefold greater compared to three decades ago.

As the first time, 0D-1D-3D and fully 3D steady-state aero-thermo-fluid simulations of a structural oil-to-air Fan Outlet Guide Vane Cooler (FOGVC) in a jet engine are presented. Using the commercial softwares Ansys Fluent, the thermo-mechanical module of Ansys and the 1D fluid solver Flownex, 5 simulation types (3D fully conjugate heat transfer with and without a thin wall model, 3D with a thin wall model, 1D-3D coupled, 1D and 0D) corresponding to 4 levels of simplification in 3 possible domains (oil, oil-metal and oil-metal-air) have been compared to provide selection criteria when a determined level of accuracy in the simulations without prohibited computational times is desired. The methodologies are applied to two different oil internal cavities: an inverted U with rectangular cross section and a coil internal cavity with a circular cross section. The obtained results show that depending on the scope of the research (outlet oil temperature, dissipated heat rate or oil pressure drop) and the accuracy of the results, one method or the other may be used. Experimental data would be needed to validate the numerical results by all employed methodologies and geometries.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

The paper presents the results of energy and environmental analysis of geothermal CHP plant operation in Polish conditions. As the most favorable, for the geothermal conditions prevailing in Poland, the variant of CHP plant based on Organic Rankine Cycle (ORC) has been taken into consideration. As the case study the existing geothermal well located in the town of Konin in the Wielkopolska voivodship has been chosen. The conceptual design of CHP plant has been proposed and evaluated from energy and environmental point of view. As energy performance criteria the non-renewable primary energy consumption has been chosen. In case of environmental performance carbon dioxide emission has been taken as evaluation criteria. The analysis has been performed for different operating conditions and three working fluids.

Water stress (WS) and heat stress (HS) have a negative effect on soybean plant growth and crop productivity. During WS, soybean plants opt for survival through ion homeostasis and the conformations of proteins are disconcerted as plant cells lose water while HS leads to difficulties in flowering and fruiting. Some of these changes include oxidative stress leading to the destruction of photosynthetic apparatus, macromolecules within cells and the onset of complex signaling cascades. Changes in the physiological characteristics, proteome, and certain metabolites investigated on molecular and cellular functions were studied in two soybean cultivars exposed to different heat and water stress conditions independently and in combination. Leaf protein composition was studied using 2-DE and complemented with MALDI TOF mass spectrometry. While two cultivars displayed genetic variation in response to water and heat stress, thirty-nine proteins were significantly altered in their relative abundance in response to WS, HS and combined WS+HS in both cultivars; a majority of them involved in metabolism, response to heat and photosynthesis showing significant cross-tolerance mechanisms. Functional analysis revealing a majority of heat responsive-proteins were more abundant during HS and combined stress (WS+HS) whereas these proteins were low to WS in cultivar PI 471938 and heat shock proteins were in low abundance to water, heat and combined stresses in cultivar R95-1705. Most protein abundances were not correlated with their expression at mRNA levels in PI cultivar, however, in cultivar R 95, the expression levels of transcript follow their relative abundance in proteins. Our systems bioinformatics analyses revealed that MED37C, a probable mediator of RNA polymerase transcription II protein showed potential interacting partners in Arabidopsis and our studies signifies the marked impact of this protein in PI cultivar. Elevated activities in antioxidant enzymes indicate that the PI-371938 cultivar has the ability to restore the oxidation levels and sustain the plant during the stress. Our study hypothesizes the plant’s development of cross-stress tolerance which will help foster the ongoing ventures in genetic modifications in stress tolerance.

Antimicrobial resistance (AMR) is a recurring global problem, which constantly demands new antimicrobial compounds to challenge the resistance. It is well known that essential oils (EOs) have been known for biological activities including antimicrobial properties. In this study, EOs from seven aromatic plants of Asir region of southwestern Saudi Arabia were tested for their antimicrobial efficacy against four drug resistant pathogenic bacterial isolates (Staphylococcus aureus, Streptococcus pyogenes, Escherichia coli and Streptococcus typhimurium) and one fungal isolate (Candida albicans). Chemical compositions of EOs were determined by Gas chromatography-Mass Spectrometry (GC-MS). The results revealed that EOs from Mentha cervina, Ocimum basilicum and Origanum vulgare proved most active against all isolates with inhibitory zone range between17 to 45 mm. The lowest minimum inhibitory concentration (MIC) of 0.025mg/ml was observed for Staph. aureus and Streptococcus pyogenes with EO of Origanum vulgare. All the three EOs showed significant anti candida activity. Together form the results the EOs from Mentha cervina, Ocimum basilicum and Origanum vulgare demonstrated a significant antimicrobial efficacy against drug resistant microorganisms.

This study aims to identify an optimal heat-treatment parameter set for an additively manufactured AlSi10Mg alloy in terms of increasing the hardness and eliminating the anisotropic microstructural characteristics of the alloy in as-built condition. Furthermore, the influence of these optimized parameters on the fatigue properties of the alloy investigated. In this respect, microstructural characteristics of an AlSi10Mg alloy manufactured by Laser-Based Powder Bed Fusion in non-heat-treated and heat-treated conditions were investigated. Their static and dynamic mechanical properties were evaluated, and fatigue behavior was explained by a detailed examination of fracture surfaces. Much of the microstructure in the non-heat-treated condition was composed of columnar grains oriented parallel to the build direction. Further analysis revealed a high fraction of pro-eutectic α-Al. Through heat-treatment, the alloy was successfully brought to its peak-hardened condition, while eliminating the anisotropic microstructural features. Yield strength and ductility increased simultaneously after heat-treatment, which is due to the relief of residual stresses, preservation of refined grains, and introduction of precipitation strengthening. The fatigue strength, calculated at 10^7 cycles, improved as well after heat-treatment and finally detailed fractography reviled that a more ductile fracture mechanism has happened in the heat-treated condition compared to the non-heat-treated condition.

This paper presents a steady-state and transient heat conduction analysis framework using the polygonal scaled boundary finite element method (PSBFEM) with polygon/quadtree meshes. The PSBFEM is implemented with commercial finite element code Abaqus by the User Element Subroutine (UEL) feature. The detailed implementation of the framework, defining the UEL element, and solving the stiffness/mass matrix by the eigenvalue decomposition are presented. Several benchmark problems from heat conduction are solved to validate the proposed implementation. Results show that the PSBFEM is reliable and accurate for solving heat conduction problems. Not only can the proposed implementation help engineering practitioners analyze the heat conduction problem using polygonal mesh in Abaqus, but it also provides a reference for developing the UEL to solve other problems using the scaled boundary finite element method.

Extracellular vesicles (EVs), such as exosomes or oncosomes are released with molecules unfavorable for survival from cells. In addition, accumulating evidence has shown that tumor cells often eject anti-cancer drugs such as chemotherapeutics and targeted drugs within EVs, a novel mechanism of drug resistance. The EV-releasing, drug resistance phenotype is often coupled with cellular dedifferentiation and transformation, cells undergoing epithelial-mesenchymal transition (EMT) and taking on a cancer stem cell phenotype. Recent studies have shown that the release of EVs is also involved in immunosuppression. The concept of the resistance-associated secretory phenotype (RASP) is reviewed herein.

Once a wheat sheaf has been sealed and tied up, its packed down straws display the same orientation and zero-divergence. This observation brings us to the mathematical notion of presheaf, i.e., a topological structure in which diverging functions are locally superimposed. We show how the concepts of presheaves and the correlated globular sets, borrowed from category theory and algebraic topology, allow a well-founded mathematical approach to otherwise elusive activities of the brain. The mathematical assessment of brain functions in terms of presheaves: a) explains why spontaneous random spikes synchronize; b) leads to the counterintuitive intuition of antidromic effects in neuronal spikes: when an entrained oscillation propagates from A to B, changes in B lead to changes in A. We provide testable previsions: a) we suggest the proper locations of transcranial magnetic stimulation’s coils to improve the clinical outcomes of drug-resistant epilepsy; b) we advocate that axonal stimulation by external sources backpropagates and alters the neuronal electric oscillatory frequency. Further, we describe how the hierarchical information transmission inside globular sets provides fresh insights concerning different issues at various coarse-grained scales, such as object persistence, memory reinforcement in spite of random noise, Bayesian inferential circuits.

Senna alata (Linn) Roxb. plant is widely used to manage various infections in folkloric medicine. Methicillin-resistant Staphylococcus aureus (MRSA) infection continues to be a major global public health problem. This study aims to investigate the bioactive components of S. alata leaves active against MRSA. The leaves of S. alata were sequentially extracted and fractionated using standard methods and screened for activities against MRSA. The diethyl ether active thin layer chromatography (TLC) spot was subjected to infrared (IR) and gas chromatography-mass spectroscopic (GC-MS) studies. The aqueous extract and diethyl ether fraction of S. alata leaves elicited the highest activity against the MRSA. The GC-MS analysis of the fraction produced 15 eluates; only the sub-fraction 13 was effective. The TLC analysis of the sub-fraction 13 revealed three spots; only the second spot produced activity. The GC-MS result of the spot showed six peaks. The spectral results for peak 3 match the data from the IR study suggestive of 9-octadecenoic acid methyl ester. Senna alata leaves possess bioactive compounds closely related to 9-octadecenoic acid methyl ester with potent antibacterial activity against MRSA.

AMR and drug void have caused huge panic today with few thousand death per year. MDR Typhoid was a serious old disease and caused serious health hazard in humen and animals demanding an update on molecular biology of the status on transferable genetic elements. R-plasmids combined in F’-plasmid and the new MDR conjugative plasmids were shown abundant in Sanmonella ranging 70-440kb with similarities. BlaTEM, blaCTX-M, blaOXA, blaNDM mdr genes were abundant in >50 plasmids analyzed and metal resistant gene clusters are predominant in most large plasmids. Among the acetyltransferase all catA1, aacA1 and aac-1b-cr genes were located. Abundant streptomycin phosphotransferases (StrAB) and rarely colistin resistant Mcr-5/9 phosphoethanolamine–lipid A transferase were detected. Altered isomeric dihydropterote synthases (Sul1/2/3) were present giving sulfamethoxazole resistance and dhfr gene frequently associated giving trimethoprim resistance. Metal resistant gene clusters like SilABC (CusABC), PcoAB, RcnA, terABC, and merABCXT etc were found in many Salmonella enterica plasmids. Toxin genes like HipA and virulence genes like spvABD were located in few plasmids increasing virulence and pathogenesis. Drug efflux genes tetA or tetB and OqxB, floR, CmlA were frequent where as QepA and EamA genes were rarely seen. Thus, Salmonella metal resistant genes combined with antibiotic resistant genes has tried to overcome the both toxic antibiotics and metalions causing Typhoid AMR. Such acquisition spreads salmoniasis in the live stocks (pig, cow, chicken) where toxic soil and water dominate increasing chance of MDR typhoid in human.

High concentrations of Na⁺ or [Co(NH₃)₆]³⁺ can induce the B to Z conformational transition in alternating (dC-dG) oligo and polynucleotides. The use of short DNA oligomers (dC-dG)₄ and (dm⁵C-dG)₄ as models can allow a thermodynamic characterization of the transition. Both form right handed double helical structures (B-DNA) in standard phosphate buffer with 115 mM Na⁺ at 25 ^oC. However, at 2.0 M Na⁺ or 200 mM [Co(NH₃)₆]³⁺, (dm⁵C-dG)₄ assumes a left handed double helical structure (Z-DNA) while the unmethylated (dC-dG)₄ analogue remains right handed under those conditions. We have previously demonstrated that the enthalpy of the transition at 25 ^oC for either inducer can be determined using isothermal titration calorimetry (ITC) [Ferreira, J. M. & Sheardy, R. D., Biophys. J. 2006, 91, 1–7]. Here, ITC is used to investigate the linkages between temperature, water activity and DNA conformation. We found that the determined enthalpy for each titration varied linearly with temperature allowing determination of the heat capacity change (DC_p) between the initial and final states. As expected, the DC_p values were dependent upon the cation (i.e. Na⁺ vs [Co(NH₃)₆]³⁺) as well as the sequence of the DNA oligomer (i. e., methylated vs unmethylated). Osmotic stress experiments were carried out to determine the gain or loss of water by the oligomer induced by the titration. The results are discussed in terms of solvent accessible surface areas, electrostatic interactions and the role of water.

Vaccination against Newcastle disease (ND), a devastating viral disease of chicken, is often hampered by thermal inactivation of the live vaccines, in particular in tropical and hot climate conditions. In the past “thermostable” vaccine strains (I-2) have been proposed to overcome this problem. In the current study, we compared the thermal stability of 6 commercially available ND vaccines. Subjected to 37°C as lyophilized preparation, two vaccines containing I-2 strains were more sensitive to inactivation than a third I-2 vaccine or when compared to three other vaccines based on different strains. However, after reconstitution strains proved to have a comparable tenacity. Interestingly, all vaccines retained a sufficient virus dose for protection (106 EID50) after 1 day at 37°C, still. However, experiments exposing ND-vaccines to elevated temperatures of 51°C and 61°C, clearly demonstrated inactivation of all dissolved vaccines within 2 to 4 hours. The data indicate preparation that specific factors may influence thermal stability rather than strain specific characteristics. Regardless of the ND strain used, the appropriate cold chain is mandatory for live ND-vaccines.

Heating systems such as heat pump and combined heat and power cycle systems (CHP) are representing a key component in the future smart grid. Their capability to couple the electricity and heat sector promises a massive potential to the energy transition. Hence, these systems are continuously studied numerical and experimental to quantify their potential and develop optimal control methods. Although numerical simulations provide time and cost-effective solution for system development and optimization, they are exposed to several uncertainties. Hardware in the loop (HiL) system enables system validation and evaluation under different real-life dynamic constraints and boundary conditions. In this paper, a HiL system of heat pump testbed is presented. This system is used to present two case studies. In the first case, the conventional heat pump testbed operation method is compared to the HiL operation method. Energetic and dynamic analyses are performed to quantify the added value of the HiL and its necessity for dynamics analysis. The second case, the HiL testbed is used to validate the heat pump operation in a single family house participating in a local energy market. It enables not only the dynamics of the heat pump and the space heating circuit to be validated but also the building room temperature. The energetic analysis indicated a deviation of 2% and 5% for heat generation and electricity consumption of the heat pump, respectively. The model dynamics emphasized the model capability to present the dynamics of a real system with a temporal distortion of 3%.

As the energy efficiency demands for future buildings become increasingly stringent, preliminary assessments of energy consumption are mandatory. These are possible only through numerical simulations, whose reliability crucially depends on boundary conditions. We therefore investigate their role in numerical estimates for the usage of geothermal energy, performing annual simulations of transient heat transfer for a building employing a geothermal heat pump plant and energy piles. Starting from actual measurements, we solve the heat equations in 2D and 3D using COMSOL Multiphysics and IDA-ICE, and discover a negligible impact of the multiregional ground surface boundary conditions. Moreover, we verify that the thermal mass of the soil medium induces a small vertical temperature gradient on the piles surface. We also find a roughly constant temperature on each horizontal cross-section, with nearly identical values if the average temperature is integrated over the full plane or evaluated at one single point. Calculating the yearly heating need for an entire building we then show that the chosen upper boundary condition affects the energy balance dramatically. Using directly the pipes’ outlet temperature induces a 54% overestimation of the heat flux, while the exact ground surface temperature above the piles reduces the error to 0.03%.

This paper emphasises on the analogous modelling of hardwood (Acacia) pyrolysis. The effect of physical characteristics of hardwood chips on the pyrolysis is examined through the conservation of solid mass fraction of biomass. The chip size of G30 and G50 are used in the pyrolysis reactor. In the analogous situation, the fixed bed is assumed to be a wooden slab with a porosity equivalent to the voidage of bed. The bulk density, the length of the bed and the porosity are some of the physical attributes of a fixed bed used to determine the variation of solid mass of the hardwood across the fixed bed. The four-temperature sensors separated from each other by 80 mm are used to determine the temperature along the length of the pyrolysis unit. The heating element of 2 kWe is used to initiate the pyrolysis of biomass. The experiments are conducted in three different stages. The ONORM standard chips, G30 and G50, and the combination of them are separately pyrolysis to determine the validity of a model for different sizes of chips. The proposed model is also used to establish the relationship between the kinetics of pyrolysis and decomposition of the hardwood.

Steel is one of the essential materials in the world's civilization. It is essential to produce many products such as pipelines, mechanical elements in machines, vehicles, profiles, and beam sections for buildings in many industries. Until the '50s of the 20th century, steel products required a complex process known as ingot casting; for years, steelmakers focused on developing and simplifying this process. The result was the con-tinuous casting process (CCP); it is the most productive method to produce steel. The CCP allows producing significant volumes of steel sections without interruption and is more productive than the formal ingot casting process. The CCP begins by transferring the liquid steel from the steel-ladle to a tundish. This tundish or vessel distributes the liquid steel, by flowing through its volume, to one or more strands having wa-ter-cooled copper molds. The mold is the primary cooling system, PCS, solidifying a steel shell to withstand a liquid core and its friction forces with the mold wall. Further down the mold, the rolls drive the steel section in the SCS. Here the steel section is cooled, solidifying the remaining liquid core, by sprays placed in every cooling segment all around the billet and along the curved section of the machine. Finally, the steel strand goes towards a horizontal-straight free-spray zone, losing heat by radiation mechanism, where the billet cools down further to total solidification. A moving torch cutting-scissor splits the billet to the desired length at the end of this heat-radiant zone.

The effects of heating rate before solution treatment and cooling rate after solution treatment on the morphological distribution and evolution of precipitation phase of nickel-based single crystal superalloy were studied. The dissolution, precipitation and growth of precipitation phase and matrix phase during heat treatment were analyzed by means of high power scanning electron microscopy. The results show that the morphology of precipitated phase has nothing to do with the distribution of precipitated phase and the heating rate in the heating process, but the cooling rate in the cooling process affects the shape, size and distribution of precipitated phase. The faster the cooling rate, the smaller the precipitated phase is, the more irregular the shape is, the smaller the equivalent edge length is, and the smaller the channel width of matrix phase is.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

Plants thriving in desert environments are suitable for studying mechanisms for plant survival under extreme seasonal climate variation. Zygophyllum dumosum Boiss, like many other Zygophyllaceae species, displays a unique epigenetic mechanism whereby the repressive markers di- and tri-methyl of H3K9 do not exist. We studied epigenetic mechanisms underlying seasonal growth cycles in Z. dumosum and their association with factors regulating basic cell functions. We showed strong association between rainfall and seasonal growth and the epigenetic marker of dimethyl H3K4, which disappears on entry into the dry season and the acquisition of dormant state. DNA methylation is not affected by lack of H3K9 di and tri methyl and changes in methylation pattern are apparent on entry into the dry season. Proteome analysis of acid soluble fractions revealed extensive reduction in ribosomal proteins and in proteins involved in chloroplasts and mitochondria activities during the dry seasons concomitantly with up-regulation of molecular chaperone HSPs. Our results highlight mechanisms underlying Z. dumosum adaptation to seasonal climate variation. Particularly, summer dormancy is associated with loss of the permissive epigenetic marker dimethyl H3K4, which might facilitate genome compaction, concomitantly with significant reduction in proteins involved in basic cell functions (i.e., protein synthesis, photosynthesis and respiration).

The objective of this study was to evaluate the effect of in ovo injection of L-arginine (L-Arg) into Ross broiler eggs at different embryonic developmental stages on their survival, hatchability, and body weight (BW). Additionally, we have analyzed the levels of serum glutamic-oxaloacetic transaminase (SGOT) and serum glutamic-pyruvic transaminase (SGPT), protein expression of heat shock proteins (HSPs), also we have the determined micronuclei (MN) and nuclear abnormality (NA). Results showed that survival and hatching rates as well as body weight were increased on the 14th day incubation compared to 8th and 18th day incubation at lower concentration of L-Arg. Moreover, the levels of SGOT and SGPT were also significantly (P < 0.05) increased at 14th day incubation at the same concentration (100μg/μl/egg) of injection. In addition, IgM levels were increased on the 14th day incubation compared to other days. The protein expressions of HSP-47, HSP-60, and HSP-70 in the liver were significantly down-regulated whereas the expression of myogenin and MyoD were significantly up-regulated on the 14th day after incubation in treated with all different doses such as 100μg, 1000μg and 2500μg/μl/egg namely 3T1, 3T2 and 3T3 respectively. However, the treatment with low dose of L-Arg down-regulated expression levels of those proteins on the 14th day incubation. Histopathology of liver by hematoxylin and eosin (H&E) straining showed that the majority of liver damage, specifically intracytoplasmic vacuoles, were observed in 3T1, 3T2, and 3T3. The minimum dose of 100 μg/ml/egg on the 14th day of incubation significantly prevented intracytoplasmic vacuole damages. These results demonstrate that in ovo administration of L-Arg at (100μg/μl/egg) may be an effective method to increase chick BW, hatch rate, increasing muscle growth related proteins and promote the immune response through increasing IgM on the 14th day of incubation period.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

The aim of this paper is to expose the main involved physical phenomena underlying the alteration of convective heat transfer in a heat exchanger subjected to imposed vibrations. This technique seems to have interesting features and industrial applications, such as efficiency increase, heat transfer rate control and cleanliness action. However, a clear description and comprehension of how vibrations may alter the convective heat transfer coefficient in a heat exchanger is no still reached due to the complexity of the involved physical mechanisms. For this reason, after a presentation and a schematisation of the analyzed thermodynamic system, the fundamental alterations of the thermo-fluid dynamics fields are described. Then, the main involved physical phenomena are exposed for the three cases of gaseous, monophasic liquid and boiling liquid mediums. Finally, on the basis of the characteristics of these described phenomena, some considerations and indications of general validity are presented.

This paper shares some new information on the ambient temperature profile and the heat stress occurrences directly underneath ground-mounted Solar Photovoltaic (PV) Arrays (monocrystalline-based) focusing on different temperature levels. A common ground for this work lies on the fact that 10C increase of PV cell temperature results in reduction of 0.5% energy conversion efficiency thus any means of natural cooling mechanism would gain much benefit especially to the Solar Farm operators. Transpiration process plays an important role in the cooling of green plants where in average it could dissipate around 32.9% of the total solar energy absorbed by the leaf making it a good natural cooling mechanism. This condition is relatively applied for herbs specifically for this project, Orthosiphon Stamineus or generally known as Java Tea are used as the high value crops. The thermal process via convective heat and mass exchange of leaves with the environment is relevant for a better understanding of plant physiological processes in response to environmental conversion factors for a wide range of applications. An important fact for plant heat stress with respect to the Ambient temperature is that the range lies between 10 C to 15 C above the surrounding value. This heat stress condition is relatively important and should be modelled in crops-energy integration. Agrivoltaic concept is a system that combines commercial agriculture and photovoltaic electricity generation in the same space. The concept is in line with the Kyoto Protocol and the United Nation Sustainable Development Goals (UN-SDG) which highlights the clean energy and sustainable urban living. The integration of agrivoltaic systems would optimize the yield, improving clean system efficiency and solving the issue of land resource sustainability. The PV bottom surface temperature are the main source of dissipated heat as shown in the thermal images recorded at 5 minutes interval at 3 sampling time. Statistical analysis shows that the Thermal correlations for transpiration process and heat stress occurrences between PV bottom surface and plant height will be an important finding for large scale plant cultivation in agrivoltaic farms.

The tribological performance of metalwork steel tools is of vital importance in both cold and hot working processes. One solution for improving metal tool life is the application of coatings. This paper investigates the effect of CrAlSiN thin-film PVD-deposition on the tribological behaviour of tool steel K340. The sliding wear performance of the coated K340 steel is analysed in relation to both the uncoated K340 steel and a range of tool steels dedicated to hot- and cold-working, such as X155CrVMo12-1, X37CrMoV5-1, X40CrMoV5-1, 40CrMnMo7 and 90MnCrV8. The investigated tool steels were heat-treated, while K340 was subjected to thermochemical treatment and then coated with a CrAlSiN hard film (K340/CrAlSiN). The hardness, chemical composition, phase structure and microstructure of steels K340 and K340/CrAlSiN are examined. Tribological tests were conducted using the ball-on-disc tester in compliance with the ASTM G99 standard. The tests were performed under dry unidirectional sliding conditions, using an Al2O3 ball as a counterbody. The wear factor and coefficient of friction are estimated and analysed with respect to hardness and alloying composition of the materials under study. SEM observations are made to identify the sliding wear mechanisms of the analysed tool steels and PVD-coated K340 steel. In contrast to the harsh abrasive-adhesive wear mechanism observed for uncoated tool steels, the abrasive wear dominates in case of the AlCrSiN. The deposited thin film effectively prevents the K304 substrate from harsh wear severe degradation. Moreover, thanks to the deposited coating, the K304/CrAlSiN sample has a COF of 0.529 and a wear factor of K=5.68×10−7 m3 N−1 m−1, while the COF of the reference tool steels ranges from 0.702 to 0.885 and their wear factor ranges from 1.68×10−5 m3 N−1 m−1 to 3.67×10−5 m3 N−1 m−1. The CrAlSiN deposition reduces the wear of the K340 steel and improves its sliding properties, which makes it a promising method for prolonging the service life of metalwork tools.

Geranylgeranyl acetone (GGA) protects against various types of cell damages by upregulating heat shock proteins. We investigated whether GGA protect neuronal cells from cell death induced by oxidative stress. Glutamate exposure was lethal to HT-22 cells which comprise a neuronal line derived from mouse hippocampus. This configuration is often used as a model for hippocampus neurodegeneration in vitro. In the present study, GGA protected HT-22 cells from glutamate-induced oxidative stress. GGA pretreatment did not induce Hsps. Moreover, reactive oxygen species increased to the same extent in both GGA-pretreated and untreated cells exposed to glutamate. In contrast, glutamate exposure and GGA pretreatment increased mitochondrial membrane potential. However, increases in intracellular Ca2+ concentration were inhibited by GGA pretreatment. In addition, the increase of phosphorylated ERKs by the glutamate exposure was inhibited by GGA pretreatment. These findings suggest that GGA protects HT-22 cells from glutamate-provoked cell death without Hsp induction and that the mitochondrial calcium buffering capacity plays an important role in this protective effect.

In order to design efficient and sustainable office spaces and to automate lighting, heating and air circulation in these facilities, solving the challenge of occupancy prediction is crucial. In office spaces where large areas need to be observed, multiple sensors must be used for full coverage. In these cases, it is normally important to keep the costs low, but also to make sure that the privacy of the people who use such environments are preserved. Low-cost and low-resolution heat (thermal) sensors can be very useful to build solutions that address these concerns. However, they are extremely sensitive to noise artifacts which might be caused by heat prints of the people who left the space or by other objects which are either using electricity or exposed to sunlight. There are some earlier solutions for occupancy prediction that employ low-resolution heat sensors, however, they have not addressed nor compensate for such heat artifacts. Therefore, in this paper, we present a low-cost and low-energy consuming smart space implementation to predict the number of people in the environment based on whether their activity is static or dynamic in time. We use a low-resolution (8×8) and non-intrusive heat sensor to collect data from an actual meeting room. We propose two novel workflows to predict the occupancy; one based on computer vision and one based on machine learning. Besides comparing the advantages and disadvantages of these different workflows, we use several state-of-the-art explainability methods in order to provide a detailed analysis of the algorithm parameters and how the image properties influence the resulting performance. Furthermore, we analyze noise resources which affect the heat sensor data. We hope that our analysis brings light into understanding how to handle very low-resolution heat images in these environments. The presented workflows could be used in various domains and applications other than smart offices, where occupancy prediction is essential, e.g., for elderly care.

In the past two decades the world experienced an exceptional number of unprecedented extreme weather events, some causing major human suffering and economic damage, such as the March 2012 heat event, which was called “Meteorological March Madness.” From the beginning of space era a correlation of solar flares with pressure changes in atmosphere within 2–3 days or even less was reported. In this study we wanted to test the possible relation of highly warm weather events in North-East America with Solar Energetic Particle (SEP) events. For this reason we compared ground temperatures T_M in Madison, Wisconsin, with energetic particle fluxes P measured by the EPAM instrument onboard the ACE spacecraft. In particular, we elaborated case events and the results of a statistical study of the SEP events related with the largest (Dst ≤ −150nT) Coronal Mass Ejection (CME)-induced geomagnetic storms, between with the years 1997–2015. The most striking result of our statistical analysis is a very significant positive correlation between the highest temperature increase_. ΔT_M and the time duration of the temperature increase ΔT_M (r = 0.8, p <0.001) at “winter times” ( r = 0.5, p , 0.01 for the whole sample of 26 SEP examined events). The time response of T_M to P was found to be in general short (a few days), but in the case of March 2015, during a gradual P8 increase, a cross-correlation test indicated highest c.c. within 1 day (p < 0.05). The March 2012 “meteorological anomaly” was elaborated in the case of South-East Europe, where, beside a period of strong winds and rainfall (6-13.3.2012), intense precipitation in North-East Greece (Alexandroupoli) were found to be correlated with distinct high energy flux enhancements. A rough theoretical interpretation is discussed for the space—atmospheric extreme weather relationship we found. However, much work should be done to achieve early warning of space weather dependent extreme meteorological events. Such future advances in understanding the relationships between space weather and extreme atmospheric events would improve atmospheric models and help people’s safety, health and life.

Tumor cells exhibit a resistance-associated secretory phenotype involving extracellular vesicles (EVs) and heat shock proteins (HSPs). This response occurs in response to cell stress and cancer therapeutics. HSPs are stress-responsive molecular chaperones promoting proper protein folding, while also being released from cells with EVs as well as in free form as alarmins. We have here investigated the secretory phenotype of castration-resistant prostate cancer (CRPC) cells using proteome analysis. We have also examined the roles of the key co-chaperone CDC37 in stressome release, epithelial-to-mesenchymal transition (EMT), and tumor progression. A number of HSP family members and their common receptor CD91/LRP1 were enriched at high levels in CRPC cell-derived EVs among over 700 other protein species. The small EVs (30 to 200 nm in size, potentially exosomes) were released even in a non-heated condition from the prostate cancer cells, whereas EMT-coupled release of EVs (200 to 500 nm, likely ectosomes) with associated HSP90α was increased after heat shock stress (HSS). Lactate dehydrogenase, a marker of membrane leakage/damage of cells, was also released upon HSS from the prostate cancer cells. During this stress response, intracellular CDC37 was also transcriptionally inducible by heat shock factor 1, and knockdown of CDC37 decreased EMT-coupled release of EVs. Triple knockdown of CDC37, HSP90α, and HSP90β was required for efficient reduction of the chaperone trio and to reduce tumorigenicity of the CRPC cells in vivo. Taken together, the data indicated that CDC37 and HSP90 are essential for stressome release and for tumorigenesis in resistant cancer.

Bifidobacteria have long been recognized as bacteria with probiotic and therapeutic features. The aim of this work is to characterize the Bifidobacterium asteroides BA15 and BA17 strains, isolated from honeybee gut. An in-depth assessment was carried out on safety properties (antibiotic resistance profiling, β-haemolytic, DNAse and gelatinase activities and virulence factor presence) and other properties (antimicrobial activity, auto-aggregation, co-aggregation and hydrophobicity). Based on phenotypic and genotypic characterization, both strains satisfied all the safety requirements. More specifically, genome analysis showed the absence of genes encoding for glycopeptide (vanA, vanB, vanC-1, vanC-2, vanD, vanE, vanG), resistance to tetracycline (tet-M, tet-L and tetO), and virulence genes (asa1, gelE, cylA, esp, hyl).

Cities worldwide are facing ever-increasing pressure to develop mitigation strategies for all sectors to deal with the impacts of climate change. Cities are expected to house 70% of the world’s population by 2050 and developing related resilient health systems is a significant challenge. Because of their physical nature, cities’ surface temperatures are often substantially higher than that of the surrounding rural areas, generating the so-called Urban Heat Island (UHI) effect. Whilst considerable emphasis has been placed on strategies to mitigate against the UHI-associated negative health effects of heat and pollution, the World Health Organization estimates that one of the main consequences of global warming will be an increased burden of such vector-borne diseases. Many of the major mosquito-borne diseases are urban and thus the global population exposed to these pathogens will steadily increase. Mitigation strategies beneficial for one sector may, however, be detrimental for another. Implementation of inter-sectoral strategies that can benefit many sectors (such as water, labour and health) do exist and would enable optimal use of the meagre resources available. Discussion among inter-sectoral stakeholders should be actively encouraged.

This article investigates the features of heat and mass transfer for the steady two-dimensional Williamson nanofluid flow across an exponentially stretched surface depending on suction/injection. The boundary conditions incorporate the impacts of the Brownian motion and thermophoresis boundary. The analysis of heat transfer is carried out for the two cases of prescribed exponential order surface temperature (PEST) and prescribed exponential order heat flux (PEHF). The ongoing flow problem is mathematically modeled under the basic laws of motion and heat transfer. The similarity variables are allowed to transmute the governing equations of the problem into a similarity ordinary differential equation (ODEs). The solution of this reduced non-linear system of ODEs is supported by the Homotopy analysis method (HAM). The combination of HAM arrangements is acquired by plotting the h-curve. In order to evaluate the influence of several emergent parameters, the outcomes are presented numerically and are plotted diagrammatically as a consequence of velocity, temperature and concentration proles.

One of the most destructive natural disasters is the earthquake which brings enormous risks to humankind. The objective of the current study was to determine the Earthquake’s remote sensing multiparameter (i.e. land surface temperature (LST), air temperature, specific humidity, precipitation and wind speed) spatiotemporal anomaly of many earthquake samples occurred during 2018 around the world. In this research 11 earthquake (M > 6:0) studied (4 samples selected in a land with transparent sky situations, 3 samples in land within cloudy situations and 4 samples in marine earthquakes). The interquartile range (IQR) and mean ± 2σ methods utilized to improve the efficiency of anomalous differences. As a result, based on the IQR method, negative anomaly before the event detected during the daytime in Mexico and during the nighttime in Afghanistan. In addition, a negative outlier of brightness temperature (BT) detected in Alaska before, after and during the event. In contrast, based on IQR and mean ± 2σ positive anomaly detected in precipitation before and after the event in all investigated examples. According to mean ± 2σ, negative anomaly LST, specific humidity, sea surface temperature (SST_100) and wind detected in most examined earthquake samples. In contrast, positive SST_0 anomaly observed in Fiji and Honduras after the earthquake. Our results suggested in marine earthquakes, for earthquake forecasting we can merge a prior negative anomaly in the wind speed and SST_100. Regarding the in land cloudy sky earthquakes, merging anomaly parameters could be the negative prior anomaly in BT, skin temperature, in contrast, a positive anomaly in precipitation. In land transparent sky earthquake, usually negative prior anomalies in air temperature, specific humidity and LST.

The object of this work is to determine the correlation on the Nusselt number on the individual rows of a four-row tubular finned heat exchanger with continuous fins with a staggered tube arrangement using CFD modelling. Correlations for calculating Darcy-Weisbach friction factors on individual tube rows were also determined. Relationships for the Nusselt number and friction factor derived for the entire exchanger based on CFD modelling were compared with those available in the literature determined using experimental data. The maximum relative differences between the Nusselt number for a four-row exchanger determined experimentally and by CFD modelling are in the range from 22% for a Reynolds number based on a tube's outside diameter of 1,000 to 30% for a Reynolds number of 13,000. The maximum relative differences between the friction factor for a four-row exchanger determined experimentally and by CFD modelling are in the range of 50% for a Reynolds number based on a tube outer diameter of 1,000 to 10% for a Reynolds number of 13,000. The CFD modeling performed shows that in the range of Reynolds numbers based on hydraulic diameters from 150 to 1,400, the Nusselt number for the first row in a four-row finned heat exchanger is about 22% to 15% higher than the average Nusselt number for the entire exchanger. In the range of Reynolds number changes based on hydraulic diameter from 2,800 to 6,000, the Nusselt numbers on the first and second rows of tubes are close to each other. Correlations on Nusselt numbers and friction factors derived for individual tube rows can be used in the design of plate-fin and tube heat exchangers used in equipment such as air-source heat pumps, automotive radiators, air-conditioning systems and in air hot-liquid coolers. In particular, the correlations can be used to select the optimum number of tube rows in the exchanger.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

Alzheimer’s disease is a prominent neurological disorder, which leads to progressive dementia. The microtubule-associated protein Tau is been considered as one of the major causes of Alzheimer’s disease. Physiologically Tau assists in the stabilization of microtubules, contrary to this the pathological state of Tau results in the formation of neurotoxic tangles of Tau. The posttranslational modifications, such as GSK-3β-mediated Tau phosphorylation results in the generation of Tau pathology. Neuroinflammation generated in Alzheimer’s disease, contributes to elevated body temperature. The aim of present work is to study the effect of high temperature on Tau phosphorylation. The neuroblastoma cells were exposed to heat stress for 40 minutes. The immunofluorescence and western blot studies suggested that high temperature increases the levels of GSK-3β in cells. Heat stressed cells was also observed to have elevated levels of phosphorylated Tau. Additionally, heat stressed cells found to have modulated nuclear transport as the level of Ran was reduced. The results of present work suggested that increased temperature could be considered as a risk factor in Alzheimer’s disease as it elevated the GSK-3β levels in cells thus, resulting in increased Tau phosphorylation.

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

The study of long-term average weather patterns is known as climatology. It is a distinct field of study from meteorology and can be broken down into several subdivision. In order to predict the future, the knowledge of climatology is essential. In other words, with the help of climatology, we can figure out how likely it is that snow and hail will fall to the ground, and how much solar thermal radiation can reach a certain location etc. Climatology often focuses on how the climate has changed over time and how it has affected people and events. Both meteorology and climatology fall under the general term "meteorology", in particular, they are subdivision of research in the same field. In case of predicting the weather, meteorologists use variables such as humidity, air pressure, and temperature. This article's primary objective is to familiarize engineers with the fundamentals of climate and its processes so that they can effectively apply this knowledge to comprehend the climatic impact on water resources systems.

Heat stress occurring during the reproductive stage of wheat has a detrimental effect on productivity. A durum wheat core set was exposed to simulated terminal heat stress by applying plastic tunnels at the time of flowering over two seasons. Mean grain yield was reduced by 54% compared to control conditions, and grain number was the most critical trait for tolerance to this stress. The combined use of tolerance indices and grain yield identified five elites: Kunmiki, Berghouata1, Margherita2, IDON37-141, and Ourgh. The core set was also subjected to genome wide association study using 7,652 polymorphic SNPs markers. The most critical genomic regions were identified in association with spike fertility and tolerance indices on chromosome 1A, 5B and 6B. Haplotype analysis on a set of 208 elites confirmed that lines that carried the positive allele at all three QTLs resulted in a yield advantage of 8% when field tested under daily temperatures above 31° C. Two of the QTLs were successfully validated into KASP markers and explained >10% of the phenotypic variation for an independent elite germplasm set. These genomic regions can now be readily deployed via breeding to improve resilience to climate change and increase productivity in heat-stressed areas.

The accuracy of sales prediction models based on the big data of online word-of-mouth (eWOM) is still not satisfied. We argue that eWOM contains heat and sentiments of different product dimensions, which can improve the accuracy of these models. In this paper, we propose a dynamic topic analysis (DTA) framework in order to extract heat and sentiments of product dimensions from the big data of eWOM. Finally, we propose an autoregressive-heat-sentiment (ARHS) model, which integrates heat and sentiments of dimensions into the baseline predictive model. The empirical study in movie industry confirms that heat and sentiments of dimensions can improve the accuracy of sales prediction model. ARHS model is better for movie box-office revenue prediction than other models.

When considering implementation of shallow geothermal energy as a renewable source for heating and cooling of the building, special care should be taken in hydraulic design of borehole heat exchanger system. Laminar flow can occur in pipes due to usage of glycol mixture at low temperature or inadequate flow rate. This can lead to lower heat extraction and rejection rates of the exchanger because of higher thermal resistances. Furthermore, by increasing flow rate to achieve turbulent flow and satisfactory heat transfer rate can lead to increase the pressure drop of the system and oversizing of circulation pump which leads to impairment of seasonal coefficient of performance at the heat pump. Most frequently used borehole heat exchanger system in Europe is double-loop pipe system with smooth inner wall. Lately, development is focused on implementation of different configuration as well as with ribbed inner wall which ensures turbulent flow in the system, even at lower flow rates. At a location in Zagreb, classical and extended thermal response test was conducted on three different heat exchanger configurations in the same geological environment. With classic TRT test, thermogeological properties of the ground and thermal resistance of the borehole were determined for each smooth or turbulator pipe configuration. Extended Steady-State Thermal Response Step Test (TRST) was implemented, which incorporate series of power steps to determine borehole extraction rate at the define steady-state heat transfer conditions of 0/-3°C. Results show that heat exchangers with ribbed inner pipe wall have advantages over classic double-loop smooth pipe design, in terms of greater steady state heat extraction rate and more favorable hydraulic conditions.

Carbapenem resistant Enterobacteriaceae (CRE) has been public health risk in several countries and recent reports indicate the emergence of CRE in food animals. This study was conducted to investigate the occurrence, resistance patterns, and phylogenetic diversity of CRE E.coli from chicken. Routine bacteriology, PCR detection of E.coli species, multiplex PCR to detect carbapenemase encoding genes and phylogeny of CRE E. coli were conducted. The results show that 24.36 % (19/78) were identified as CRE based on the phenotypic identifications of which 17 were positive for the tested carabanemase genes. The majority, 57.99% (11/19) of the isolates harbored multiple carbapenemase genes. Four isolates harbored all blaNDM blaOXA, blaIMP, five and two different isolates harbored blaNDM and blaOXA, and blaOXA and blaIMP respectively. The Meropenem, Imipenem and Ertapenem MIC values for the isolates ranged from 2g/mL to ≥256g/mL. Phylogenetic grouping showed that the CRE E.coli isolates belonged to five different groups; groups A, B1, C, D and unknown. The detection of carbapenem resistant E.coli in this study shows that CRE is has become an emerging problem in farm animals, particularly, in poultry farms. This also implies the potential public health risks posed by CRE from chicken to the consumers.

The use of different primary energy sources in human society has led to two major polluting emissions in the environment: energy (mostly heat), and chemical substances (mostly carbon dioxide). In this paper, the total global anthropogenic emissions of heat to the atmosphere during the industrial era (years 1850-2018) were determined and their effect on the change of global atmospheric temperature was calculated. The concept of a theoretical three-phase Earth reactor was introduced to estimate global atmospheric temperature increase caused by anthro-pogenic heat emissions. The resulting calculations closely approximated the actual atmospheric temperature change recorded during the last 170-year period. These results suggest that the temperature change of the atmosphere (global warming) is entirely due to anthropogenic heat emissions.

The need to address climate change and establish sustainable urban environments has driven increased efforts in Europe to develop climate-neutral cities. This study highlights the importance of integrating solar energy technologies and nature-based solutions as key strategies to achieve climate neutrality. By examining current practices, emerging trends, and case examples, it explores the benefits, challenges, and prospects associated with the integration of solar energy and nature-based solutions in urban contexts. The study presents a pioneering approach to assess the urban heat and climate change mitigation benefits of combining building-integrated photovoltaics and nature-based solutions specifically within the European context. The results emphasize the synergistic relationship between nature-based components and solar conversion technology, identifying effective combinations for different climatic zones. In warmer regions of Southern Europe, strategies like rooftop photovoltaics on cool roofs, photovoltaics shadings, green walls, and urban trees have demonstrated effectiveness. Conversely, mid- and high-latitude European cities have seen positive impacts through the integration of rooftop photovoltaics and photovoltaics facades with green roofs and green spaces. As solar cell conversion efficiency improves, the environmental impact of photovoltaics is expected to decrease, facilitating their integration into urban environments. The study emphasizes the importance of incorporating water bodies, cool pavements, spaces with high sky-view factors, and effective planning in urban design to maximize resilience benefits. It also highlights the significance of prioritizing mitigation actions in low-income regions and engaging citizens in the development of social photovoltaics positive energy houses, resilient neighbourhoods, and green spaces. By adopting these recommendations, European cities can lead the way in creating climate-neutral urban environments that prioritize clean energy, nature-based solutions, and the overall well-being of residents. The findings underscore the need for a multidisciplinary approach that combines technological innovation, urban planning strategies, and policy frameworks to effectively achieve climate neutrality in European cities.

The heat and matter transfer during glucose catabolism in living systems and their relation with entropy production are a challenging subject of the classical thermodynamics applied to biology. In this respect, an analogy between mechanics and thermodynamics has been performed via the definition of the entropy density acceleration expressed by the time derivative of the rate of entropy density and related to heat and matter transfer in minimum living systems. Cells are regarded as open thermodynamic systems that exchange heat and matter resulting from irreversible processes with the intercellular environment. Prigogine’s minimum energy dissipation principle is reformulated using the notion of entropy density acceleration applied to glucose catabolism. It is shown that, for out-of-equilibrium states, the calculated entropy density acceleration is finite and negative and approaches as a function of time a zero value at global thermodynamic equilibrium for heat and matter transfer independently of the cell type and the metabolic pathway. These results could be important for a deeper understanding of entropy generation and its correlation with heat transfer in cell biology with special regard to glucose catabolism representing the prototype of irreversible reactions and a crucial metabolic pathway in stem cells and cancer stem cells.

The model proposed in this study was based on the assumption that the biomass attached to the anode served as biocatalysts for MFC exoelectrogenesis, and this catalytic effect was quantified by the exchange current density of anode. By modifying the Freter model and combining it with the Butler-Volmer equation, this model could adequately describe the processes of electricity generation, substrate utilization, and the suspended and attached biomass concentrations, at both batch and continuous operating modes. MFC performance is affected by the operating variables such as initial substrate concentration, external resistor, influent substrate concentration, and dilution rate, and these variables were revealed to have complex interactions by data simulation. The external power generation and energy efficiency were considered as indices for MFC performance. The simulated results explained that an intermediate initial substrate concentration (about 100 mg/L under this reactor configuration) needed to be chosen to achieve maximum overall energy efficiency from substrate in the batch mode. An external resistor with the value about that of the internal resistance boosted the power generation, and a resistor with several times of that of the internal resistance achieved better overall energy efficiency. At continuous mode, dilution rate significantly impacted the steady-state substrate concentration level (thus substrate removal efficiency and rate), and attached biomass could be fully developed when the influent substrate concentration was equal to or higher than 100 mg/L at any dilution rate of the tested range. Overall, this relatively simple model provided a convenient way for evaluating and optimizing the performance of MFC reactors by regulating operating parameters.

Varroa destructor is considered one of the most devastating parasites of the honey bee, Apis mellifera, and a major problem for the beekeeping industry. Currently, the main method to control Varroa mites is the application of drugs that contain different acaricides as active ingredients. The pyrethroid tau-fluvalinate is one of the acaricides most widely used in beekeeping due to its efficacy and low toxicity to bees. However, the intensive and repetitive application of this compound produces a selective pressure that, when maintained over time, contributes to the emergence of resistant mites in the honey bee colonies, compromising the acaricidal treatments efficacy. Here we studied the presence of tau-fluvalinate residues in hives and the evolution of genetic resistance to this acaricide in Varroa mites from honeybee colonies that received no pyrethroid treatment in the previous four years. Our data revealed the widespread and persistent tau-fluvalinate contamination of beeswax and beebread in hives, an overall increase of the pyrethroid resistance allele frequency and a generalized excess of resistant mites relative to Hardy-Weinberg equilibrium expectations. These results suggest that tau-fluvalinate contamination of the hives may seriously compromise the efficacy of pyrethroid-based mite control methods.

Diarrhoea caused by enterotoxigenic Escherichia coli is one of the leading causes of mortality in children under five years of age and is a great burden on developing countries. The major virulence factor of the bacterium is the heat-labile enterotoxin (LT), a close homologue of the cholera toxin. The toxins bind to carbohydrate receptors in the gastrointestinal tract, leading to toxin uptake and, ultimately, to severe diarrhoea. Previously, LT from human- and porcine-infecting ETEC (hLT and pLT, respectively) were shown to have different carbohydrate-binding specificities, in particular with respect to N-acetyllactosamine-terminating glycosphingolipids. Here, we probed eleven single-residue variants of the heat-labile enterotoxin with surface plasmon resonance spectroscopy and compared the data to the parent toxins. In addition we present a 1.45 Å crystal structure of pLTB in complex with branched Lacto-N-neohexaose (Galbeta4GlcNAcbeta6[Galbeta4GlcNAcbeta3]Galbeta4Glc). The largest difference in binding specificity is caused by mutation of residue 94, which links the primary and secondary binding sites of the toxins. Residue 95 (and to a smaller extent also residues 7 and 18) also contribute, whereas residue 4 shows no effect on monovalent binding of the ligand and may rather be important for multivalent binding and avidity.

The one-to-one structural correspondence between any conjugated hydrocarbon CnHm and the borane BnHm+n is extended here, with the B3LYP/cc-pVDZ model, to pure conjugated carbon systems with the example of buckminsterfullerene C60 with the corresponding icosahedral isoelectronic system closo-borane B60H60, and the fluorine substituted systems B60F30H30 and B60F60 , all with icosahedral Ih symmetry. All systems correspond to energy minima in the potential energy hypersurface, except for B60(F30)in(H30)out . Selected electronic structure methods are used to characterize all systems: molecular electrostatic potentials (MEP), atomic charges, bond orders, and topological properties of the electron density within quantum theory of atoms-in-molecules (QTAIM) and electron-localization function (ELF) theory. In the particular case of B60H60 we use the recently developed Hückeloid model to characterize this system. The stability of the energy minimum icosahedral structure B60F60 could have an origin in F···F attractive interactions of the inner fluorine atoms of the cage.

Heat metres are used to calculate the consumed energy in central heating systems. The subject of this article is to prepare a method of predicting a failure of a heat meter in the next settlement period. Predicting failures is essential to coordinate the process of exchanging the heat metres and to avoid inaccurate readings, incorrect billing and additional costs. The reliability analysis of heat metres was based on historical data collected over many years. Three independent models of machine learning were proposed, and they were applied to predict failures of metres. The efficiency of the models was confirmed and compared using the selected metrics. The optimisation of hyperparameters characteristics for each of models was successfully applied. The article shows that the diagnostics of devices does not have to rely only on newly collected information, but it is also possible to use the existing big data sets.

Estimating heat emission losses of heating systems is an important task of energy efficiency assessments in buildings. To this aim, the present international standards contain tabulated values for different emitter and control system configurations, without however explaining how to compute the effect of increased setpoint temperatures on the system losses. Moreover, the effects of each component are treated as independent, while e.g. vertical stratification and temperature control of the system are cross-related. In this paper we attempt to fill this gap by proposing a calculation method to calculate the product category specific setpoint variations for space heating emitters, accounting for the overall heat balance in the enclosure and including the cross-correlations of each component as well. The emission losses of a heating system are computed using a temperature setpoint variation method that is imposed on annual energy calculations. This complements the procedure presented in the Standard EN15316-2, also providing the possibility to use product-specific values of setpoint variations instead of tabulated values. As the main finding of the study, the calculation process is defined for a European Reference Room, namely for a specific enclosure that allows an accurate and transparent evaluation of the total setpoint variation. The product-specific values of setpoint variations are calculated from measured vertical stratification and control parameters with an annual simulation model of the European Reference Room. The total setpoint variations were simulated for a set of heat emitters and controllers in order to quantify and compare the energy performance of a new and an old type building located in Strasbourg. We find that the total setpoint variation required to overcome emission losses is up to 2.00 °C in the old building and 1.20 °C in the new building, corresponding respectively to an increase in total heating energy usage of up to 22% and 20%.

The future power equipment tends to take hydrogen or middle/low heat-value syngas as fuel for low emission. The heat transfer of film cooled turbine blade shall be influenced more by radiation. Its characteristic of conjugate heat transfer is studied experimentally and numerically in the paper by considering radiation heat transfer, multi-composition gas and TBC. The Weighted Sum of Gray Gases spectral model and Discrete Transfer Model are utilized to solve the radiative heat transfer in the multi-composition field, while validated against the experimental data for the studied cases. It is shown that the plate temperature increases significantly when considering the radiation and the temperature gradient of the film cooled plate becomes larger. It is also shown that increasing percentage of steam in gas composition results in increased temperature on the film-cooled plate. The normalized temperature of the film-cooled plate decreases about 0.02, as the total percentage of steam in hot gas increases per 7%. As for the TBC effect, it can smooth out the the temperature distribution and insulate the heat to a greater extent when the radiative heat transfer becomes significant.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

Recent advances and demands in clinical applications drive a large amount of research to hydroxyapatite (HA) composite coatings fabricated by plasma spray. However, lower degree of HA crystallinity related to high temperature exposure in plasma spray usually leads to rapid weakening and disintegration of HA coatings and often promotes inflammatory responses in the surrounding tissue. In this research, graphene nanosheet (GNS) reinforced HA coatings were fabricated using plasma spray and followed by heat and hydrothermal treatment (hereafter referred to as thermal treatment). The addition of GNSs resulted in competing phenomenon to influence HA crystallinity viz. increased portion of the partially melted/unmelted zones and higher cooling rate during splat formation, leading to slight increase in HA crystallinity (~46.0-51.3%) in the as-sprayed coating. XRD and FTIR results showed that thermal treatment was capable of inducing significant transformation of amorphous HA to the crystalline form and removing other foreign non-HA compounds through regaining OH- ion, and therefore HA coatings displayed ~45.5-47.1% improvements in HA crystallinity regardless of addition or not of the GNS nanofillers. Microstructure observations revealed that thermal treatment enabled microcrack propagation due to stresses caused by crystallisation and phase transformations, and the residual partially melted/unmelted zone of the thermally treated GNS/HA coating was significantly decreased in size. More importantly, the added GNSs contributed greatly to the significant increase in surface nanoroughness of the thermally treated HA coatings owing to the fact that much more structural defects along with the GNSs mainly induced by thermal treatment might act as nucleation sites to accelerate HA nanoparticle precipitation, which would be beneficial for the improved adhesion strength of the osteoblast cells on the coating surface.

Cells form a bipolar spindle during mitosis to ensure accurate chromosome segregation. Proper spindle architecture is established by a set of kinesin motors and microtubule-associated proteins. In most eukaryotes, kinesin-5 motors are essential for this process, and genetic or chemical inhibition of their activity leads to the emergence of monopolar spindles and cell death. However, these deficiencies can be rescued by simultaneous inactivation of kinesin-14 motors, as they counteract kinesin-5. We conducted detailed genetic analyses in fission yeast to understand the mechanisms driving spindle assembly in the absence of kinesin-5. Here we show that deletion of the nrp1 gene, which encodes a putative RNA-binding protein with unknown function, can rescue temperature sensitivity caused by cut7-22, a fission yeast kinesin-5 mutant. Interestingly, kinesin-14/Klp2 levels on the spindles in the cut7 mutants were significantly reduced by the nrp1 deletion, although the total levels of Klp2 and the stability of spindle microtubules remained unaffected. Moreover, RNA-binding motifs of Nrp1 are essential for its cytoplasmic localization and function. We have also found that a portion of Nrp1 is spatially and functionally sequestered by chaperone-based protein aggregates upon mild heat stress and limits cell division at high temperatures. We propose that Nrp1 might be involved in post-transcriptional regulation through its RNA-binding ability to promote the loading of Klp2 on the spindle microtubules.

The principles of causality and unitarity are studied within rational nonlinear electrodynamics proposed earlier. We investigate dyonic and magnetized black holes and show that in the self-dual case, when the electric charge equals the magnetic charge, corrections to Coulomb's law and Reissner-Nordstrom solutions are absent. In the case of the magnetic black hole, the Hawking temperature, the heat capacity and the Helmholtz free energy are calculated. It is shown that there are second-order phase transitions and it was demonstrated that at some range of parameters the black holes are stable.

Heat shock protein 27 (HSP27), induced by heat shock, environmental, and pathophysiological stressors, is a multi-dimensional protein that acts as a protein chaperone and an antioxidant. HSP27 plays a major role in the inhibition of apoptosis and actin cytoskeletal remodeling. HSP27 is upregulated in many cancers and is associated with poor prognosis, as well as treatment resistance whereby cells are protected from therapeutic agents that normally induce apoptosis. This review highlights the most recent findings and role of HSP27 in cancer, as well as strategies for using HSP27 inhibitors for therapeutic purposes.

A novel mathematical model is developed to calculate the temperature distribution on the surface and bulk of a steel plate under the laser hardening process. The model starts with the basic heat equation then it is developed into a volumetric form and is connected to the various solid existing phases. The proposed model is based on three influencing parameters of the laser hardening process which are the velocity of the laser spot and irradiation time. The results are compared with the available experimental data reported in the literature. The volumetric model provides an assessment of temperature distribution in both the vertical and horizontal axis. Laser irradiation at sufficiently high fluence can be used to create a solid-state phase change on the surface. Primary calculations show that the temperature profile has a Gaussian distribution in horizontal x and y-axis and presents an exponentially decreasing in the horizontal and vertical depth directions.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

The accurate prediction of heat load profiles with a daily resolution is required for a broad range of applications such as potential studies, design, or predictive operation of heating systems. If the heat demand of a consumer is mainly caused by (production) processes independent of the ambient temperature, existing load profile prediction methods fail. To close this gap, this study develops two ex post machine learning models for the prediction of the heat demand with a daily resolution. The selected input features are commonly available to each consumer connected to public natural gas and electricity grids or operating an energy monitoring system: Ambient temperature, weekday, electricity consumption, and heat consumption of the last seven days directly before the predicted day. The study’s database covers electricity and natural gas consumption load profiles from 82 German consumers over a period of two years. Electricity and heat consumption correlate strongly with individual patterns for many consumers. Both, shallow and deep learning algorithms are evaluated. The highest accuracy is achieved by a Long Short Term Memory (LSTM) model with a median of R² of 0.94. The ex post model architecture makes the model suitable for automated anomaly detection in energy monitoring systems.

Seed germination and seedling growth represent two vulnerable stages in a plant life cycle and it is important to determine how they will be affected by environmental changes associated with climate change. This study examines the impact of salinity levels (0, 50, 100, and 150 mM) at each of three temperatures (15, 25, and 35˚C) on seed germination and radicle growth for three dormant and three non-dormant varieties of conventional, glyphosate resistant, or reduced lignin alfalfa. The genetic basis and phenotypic plasticity for seed germination and seedling growth in response to salinity and temperature were determined. Both traits were phenotypically plastic with respect to temperature and salinity. Seed germination was 87.0% ± 1.7 at 25˚C, 0mM (no salinity), but decreased to 33.9% ± 3.9 germination at 35˚C and 150mM. Radicle length went from 36.7 ± 1.5 mm after four days at 25˚C, 0mM, to 10.5 ± 0.7 mm at 35˚C, 150mM. The phenotypic response brought seed germination and radicle length away from their optimum, but we detected standing genetic variation for both seed germination and radicle length. Selection to increase both traits at high temperature and salinity would facilitate alfalfa establishment under climate change.

There is a lack of knowledge concerning the effects of ambient heat exposure on morbidity in Northern Europe. Therefore, this study aimed to evaluate the relationships of daily summer-time temperature and heatwaves with cardiorespiratory hospital admissions in the Helsinki metropolitan area, Finland. Methods: Time-series models adjusted for potential confounders such as air pollution were used to investigate the associations of daily temperature and heatwaves with cause-specific cardiorespiratory hospital admissions, during summer months of 2001-2017. Daily number of hospitalizations was obtained from the national hospital discharge register, weather information from the Finnish Meteorological Institute. Results: Increased daily temperature was associated with decreased risk of total respiratory hospital admissions and asthma. Heatwave days were associated with 20.5% (95% CI: 6.9, 35.9) increased risk of pneumonia admissions and during long or intense heatwaves also with total respiratory admissions in the oldest age group (≥ 75 years). There were also suggestive positive associations between heatwave days and admissions due to myocardial infarction and cerebrovascular diseases. In contrast, risk of arrhythmia admissions was decreased 20.8% (95% CI: 8.0, 31.8) during heatwaves. Conclusions: Heatwaves, rather than single hot days, are a health threat affecting the morbidity even in a Northern climate.

In this study, a novel porous geopolymer mortar (GP) was produced and tested experimentally. Industrial waste materials/by-products were used as constituents of the GP, along with dune sand. One sample was produced as a control sample for benchmarking. For the rest of the samples, 15%, 30%, and 45% by volume, the solid constituents were replaced with expanded polystyrene foam (EPS) beads. These mortar samples were heat cured to depolymerize the EPS to cause porosity inside the samples. Indoor experiments were conducted to evaluate the response of produced porous GP to high heat flux. The porous samples were able to reduce heat transmission across the opposite surfaces. Induced porosity resulted in a decrement in compressive strength from 77.2 MPa for the control sample to 15.8 MPa for 45% porous sample. However, the limit lies within the standards for partitioning walls in buildings and pavements in urban areas to absorb rainwater.

Placenta-derived stem cells (PDSCs) offer the advantages of possessing mesenchymal and embryonic traits, broad differentiation potential, large-scale availability, and no ethical constraints in their utilization in therapeutic applications. Elevated protein synthesis and consequently enhanced protein maintenance networks become necessary both due to the requirement to maintain stemness and respond to different stresses. This study aimed to identify the primary determinants of proteotoxic stress response in PDSCs. We generated heat-induced dose-responsive proteotoxic stress models of three stem cell types DBMSCs, DPMSCs, and pMSCs, and measured stress induction through biochemical and cell proliferation assays. RT-PCR array analysis of 84 genes involved in protein folding and protein quality control led to the identification of Hsp70 isoforms HSPA1A and HSPA1B as the prominent ones among 17 significantly expressed genes and with further analysis at the protein level through western blotting. A 24-hours’ time series analysis of stress-response allowed a detailed kinetic analysis of HSPA1A and HSPA1B gene and protein expression. More prominent differences between the two Hsp70 isoforms were detected at the translational level eluding to a potential higher requirement for HSPA1B during proteotoxic stress in PDSCs. To conclude, consideration should be given to the manipulation of definitely characterized chaperones at their expression or functional levels when utilizing PDSCs in therapeutic and regenerative applications.

Growing popularity of smart and integrated buildings requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using heat ex-changers located in the mechanical room or in the future even using an exterior wall as a heat exchanger. One may ask the question how does the earth-air heat exchanger (EAHX) technology fitts into this function. EAHX has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we reviewed literature and examined two nearly identical EAHX systems, placed either in ground next to the building or under the basement slab. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX shoud be placed under the house or near the basement foundation.

Heat and power cogeneration plants based on fuel cells are interesting systems for energy- conversion at low environmental impact. Different fuel cells have been proposed, but experimental testing rigs are expensive and the development of commercial systems is time consuming if based on fully experimental activities. Furthermore, tight control of operation of fuel cells is compulsory to avoid damage, which must be based on accurate models, able to predict the cell behaviour and prevent stresses and shut-down. Some selected examples of steady state, dynamic and fluid dynamic modelling of different types of fuel cells are proposed, mainly PEMFC and SOFC type. The general ideas behind the thermodynamic, kinetic and transport description are recalled, with some examples of models derived for single cells, stacks and integrated power co-generation units.

It is well known that the Continuous Galerkin Finite Element (CGFE) method is globally consistent with respect to the first law of thermodynamics. This means that, for any mesh, all obtained discrete solutions will conserve total energy. One might expect, that the method is, also, globally consistent with respect to the second law of thermodynamics. In this paper, we formally study if such conjecture is true. The heat conduction equation is used as the physical model for this analysis. In the present study it is proved that the conjecture is false: at least, for standard piecewise linear (1D and 2D) elements, the CGFE method is not always globally consistent with respect to the second law of thermodynamics. In other words, some obtained discrete solutions can violate the global postulate of the second law, which asserts that total entropy can never decrease.

Burning woody biomass for energy is gaining attention due to environmental issues associated with fossil fuels and carbon emission. The carbon released from burning wood is absorbed by plants and is carbon neutral. The purpose of this study was to investigate the combustion characteristics (heat calorific values and ash contents) of three timbers: Araucaria cunninghamii, Instia bijuga and Pometia pinnata and recommend for fuelwood. The test samples were sawdust particles (treatment) and solid woods (control) extracted from the heartwoods. The sawdust particles were oven-dried, sieved and pelletized into pellets using a hand-held pelletizing device, thus, forming cylindrical dimension (volume 1178.57 mm3, oven dry density 0.0008 g/mm3). While the solid woods were cubed and oven-dried (volume 1000.00 mm3, oven dry density 0.001 g/mm3). Prior to combustion in a semi-automatic bomb calorimeter, 90 test specimens (15 replicates per treatment and control per species) were conditioned to 14 % moisture content (at temperature 105 ºC) and weighed to a constant (unit) mass (1.0 g). The heat energy outputs and ash residues (of treatments) were analyzed statistically. The results indicated variability in heat energy outputs and ash residues between test specimens of the three species. Comparatively, the treatment specimens of A. cunninghamii produced higher calorific value (18.546 kJ/g) than the control (18.376 kJ/g) whilst the treatment specimens of I. bijuga and P. pinnata generated lower heat calorific values (17.124 kJ/g and 18.822 kJ/g) than the control (18.415 kJ/g and 20.659 kJ/g), respectively. According to ash content analysis, A. cunninghamii generated higher residues (6.3%) followed by P. pinnata (4.5%) and I. bijuga (2.8%). The treatment specimens of the three species could not meet the standard heat energy requirement (20.0 kJ/g) and thus, were unsuitable for fuelwood. However, the control specimens of P. pinnata generated equivalent heat energy (20.659 kJ/g) and could be a potential fuelwood.

Ocean surface heat fluxes play a significant role in the genesis and evolution of various marine-based atmospheric phenomena, from the synoptic scale down to the microscale. While in-situ measurements from buoys and flux towers will continue to be the standard in regards to surface heat flux estimates, they commonly have significant gaps in temporal and spatial coverage. Previous and current satellite missions have filled these gaps; though they may not observe the fluxes directly, they can measure the variables needed (wind speed, temperature, and humidity) to estimate latent and sensible heat fluxes. However, current remote sensing instruments have their own limitations, such as infrequent coverage, signals attenuated by precipitation, or both. The Cyclone Global Navigation Satellite System (CYGNSS) mission overcomes these limitations over the tropical and subtropical oceans by providing improved coverage in nearly all weather conditions. While CYGNSS (Level 2) primarily estimates surface winds, when coupled with observations or estimates of temperature and humidity from reanalysis data, it can provide estimates of latent and sensible heat fluxes along its orbit. This paper describes the development of the Surface Heat Flux Product for the CYGNSS mission, its current results, and expected improvements and changes in future releases.

The effect of thermal radiation on the two – dimensional, steady-state, conjugate heat transfer from a circular cylinder with an internal heat source in steady laminar crossflow is investigated in this work. P₀ (Rosseland) and P₁ approximations were used to model the radiative transfer. The mathematical model equations were solved numerically. Qualitatively, P₀ and P₁ approximations show the same effect of thermal radiation on conjugate heat transfer; the increase in the radiation – conduction parameter decreases the cylinder surface temperature and increases the heat transfer rate. Quantitatively, there are significant differences between the results provided by the two approximations.

Based on electromagnetic heat transfer and metal phase transformation co-simulations, we modeled an AISI 1045 specimen under high-frequency heat treatment. Hardening zone predictions were confirmed through cooling and metal phase transformation simulations after obtaining the results from electromagnetic heat transfer simulations. The cooling process was modeled by applying the cooling coefficient of the cooling water in the same way as the actual heat-treatment process. To obtain the current flowing through the coil during high-frequency induction heating, the voltage was measured and applied using the resistance–inductance–capacitance circuit calculation method. Experimental and simulated results of the heating temperature and curing depth of an AISI 1045 specimen with a carbon content of 0.45% were compared; the comparison indicated good agreement between the two. Using the simulation results, we established a method for obtaining the current flowing through the induction coil for predicting the extent and depth of the hardening zone during high-frequency induction heat treatment.

Plants are continually exposed to multiple stresses, which co-occur in nature and the net effects are frequently more non-additive (i.e., synergistic or antagonistic) suggesting ‘unique’ responses respect to that of the individual stress. Further, plant stress responses are not uniforms showing a high spatial and temporal variability among and along the different organs. In this respect, the present work investigated the morphological responses of different root types (seminal, seminal lateral, primary, primary lateral) of maize plants exposed to single (drought and heat) and combined stress (drought + heat). Data were evaluated by a specific root image analysis system (WinRHIZO) and analyzed by uni- and multi-variate statistical analysis. The results indicated that primary root and their laterals were the types more sensitive to the single and combined stresses while the seminal laterals specifically responded to the combined only. Further, antagonistic and synergistic effects were observed for the specific traits in the primary and their laterals and in the seminal lateral roots in response to the combined stress. These results suggested that maize root system modified specific root types and traits to face with different stressful environmental conditions highlighting that the adaptation strategy to the combined stress may be different from that of the individual ones. The knowledge of “unique or shared” responses of plant to multiple stress can be utilized to develop varieties with broad spectrum stress tolerance.

Currently, the district heating (DH) in Poland is facing many challenges. The business model used hitherto was very simple—in most cities, heating plants produced heat, and centralized heating systems supplied the "product" at a price approved annually by the president of the Energy Regulatory Office (URE). However, recent years have brought significant changes on the market. EU regulations force the elimination of old coal-fired plants that were still built in the Polish People's Republic (PRL), moreover, high prices of CO2 emission allowances aggravate the financial situation of companies. In addition, in the heating sector, the trend observed in the power sector is becoming increasingly visible—limiting the role of large sources in favor of energy generated locally, closer to the customer. One of the biggest challenges is achieving the targets set by the EU for the share of renewable energy sources (RES) in the heating sector. The war in Ukraine and problems with the supply of coal and gas are an additional impulse to turn to RES. Thus, the development of sustainable and innovative solutions for energy production and supply at the level of urban networks is currently one of the main technical challenges. The purpose of the paper is to present the current situation and perspectives of development of district heating systems in Poland with a view to the status of district heating in the world, and some deeper insight into European conditions. The review presents energy sources with particular emphasis on renewable energy sources (RES) and their cogeneration for heat production. The examples of existing heating network solutions using renewable energy sources, based on the selected published case studies, are also discussed.

In this research, a novel method to investigation the transient heat transfer coefficient in a channel is suggested experimentally, in which the water flow, itself, is considered both just liquid phase and liquid-vapor phase. The experiments were designed to predict the temporal and spatial resolution of Nusselt number. The inverse technique method is non-intrusive, in which time history of temperature is measured, using some thermocouples within the wall to provide input data for the inverse algorithm. The conjugate gradient method is used mostly as an inverse method. The temporal and spatial changes of heat flux, Nusselt number, vapor quality, convection number, and boiling number have all been estimated, showing that the estimated local Nusselt numbers of flow for without and with phase change are close to those predicted from the correlations of Churchill and Ozoe (1973) and Kandlikar (1990), respectively. This study suggests that the extended inverse technique can be successfully utilized to calculate the local time-dependent heat transfer coefficient of boiling flow.

Background: Combinatorial therapy- “nano antibiotics” is an emerging field in nanoscience. In this present investigation, we attempted to combine the green synthesized noble metal nanoparticle and the antibiotic Streptomycin to form bio-conjugated nanoparticles. The newly synthesized Nano antibiotics acted as the antibiotic carrier, functioned as cargo, and delivered the antibiotic. Methods: Comparative studies between the noble metal nanoparticles were attempted for the first time on the grounds of their antibacterial activity. The antibacterial activity of the three noble metal nanoparticles was assessed against Streptomycin-resistant Bacillus sp.; the results obtained proved that silver nanoparticles were a potent antibacterial agent. Still, no antibacterial activity was exerted by gold, and platinum nanoparticles were for the Streptomycin-resistant strain Bacillus sp. To our surprise, the gold and platinum fabricated/bio-conjugated nanoparticle with the antibiotic showed 100% antibacterial activity, whose antibacterial activity was zero when functioning as a nanoparticle alone. Results: The combinatorial therapy of two different clauses of drugs majorly increased antibacterial activity. It enhanced the antibiotic to overcome the resistance exhibited by the bacterial pathogen, and the possible mechanism is elucidated in the present study. Also, an attempt has been made to assess the nanotoxicity of the nano-bioconjugates on RBC and compare their hemocompatibility. The results obtained in the current investigation demonstrate the enhanced antibacterial activity of the green synthesized nanoparticles conjugated with the streptomycin; their efficacy for combinational therapy against resistance in pathogenic organisms highlights the novelty of the work and the comparative study of three different noble metals nanoparticles (Ag, Au, Pt) from single agro-waste for the first time.