Empirically based modeling is an essential aspect of design for a wave energy converter. These models are used in structural, mechanical and control design processes, as well as for performance prediction. The design of experiments and methods used to produce models from collected data have a strong impact on the quality of the model. This study considers the system identification and model validation process based on data collected from a wave tank test of a model-scale wave energy converter. Experimental design and data processing techniques based on general system identification procedures are discussed and compared with the practices often followed for wave tank testing. The general system identification processes are shown to have a number of advantages. The experimental data is then used to produce multiple models for the dynamics of the device. These models are validated and their performance is compared against one and other. While most models of wave energy converters use a formulation with wave elevation as an input, this study shows that a model using a hull pressure sensor to incorporate the wave excitation phenomenon has better accuracy.

In this manuscript we report new effects of resonance detuning on various dynamical parameters of a generic 3-wave system. Namely, for suitably chosen values of detuning the variation range of amplitudes can be significantly wider than for exact resonance. Moreover, the range of energy variation is not symmetric with respect to the sign of the detuning. Finally, the period of the energy oscillation exhibits non-monotonic dependency on the magnitude of detuning. These results have important theoretical implications where nonlinear resonance analysis is involved, such as geophysics, plasma physics, fluid dynamics. Numerous practical applications are envisageable e.g. in energy harvesting systems.

In this paper, we analyze the measurements of the normalized radar cross-section(NRCS) in Wave Mode for Chinese C-band Gaofen-3(GF-3) synthetic aperture radar (SAR). Based on 2779 images from GF-3 quad-polarization SAR in Wave Mode and collocated wind vectors from ERA-Interim, we verify the feasibility of using ocean surface wind fields and VV-polarized NRCS to perform normalized calibration. The method uses well-validated empirical C-band geophysical model function (CMOD4) to estimate the calibration constant for each beam. The Amazon rainforest experiment results show that the accuracy of obtained calibration constant meets the requirements. In addition, the relationship between cross-pol NRCS and wind vectors is discussed. The cross-pol NRCS increases linearly with wind speed and it has an approximate cosine modulation with the wind direction when the wind speed is greater than 8m/s. The cross-polarized system noise floor is low enough to ignore it in wind retrieval. Furthermore, we also investigate the properties of the polarization ratio, denoted PR, and show that it is dependent on incidence angle and azimuth angle. Two empirical models of the PR are fitted, one as a function of incidence angle only, the other with additional dependence on azimuth angle. Assessments show that the σ_VV^0 retrieved from new PR models as well as σ_HH^0 is in good agreement with σ_VV^0 extracted from SAR images directly. And it is also shown that considering the azimuth angle can improve polarization conversion accuracy.

By using the new recently proposed extended rational methods, we set some solitary and multi wave solutions of the coupled Higgs system in the present study. Some new families of hyperbolic and trigonometric solutions of the coupled Higgs equations are successfully obtained. Some solutions are real as some are complex valued functions. Particular forms of some solutions derived by choice of some parameters are demonstrated in three dimensional spaces. The complex valued solutions are also depicted by plotting both real and complex component.

Edge computing has emerged as a significant computing trend alongside the rapid expansion of the Internet of Things (IoT). Computing operations at the network’s edge offer a solution to the high latency and service overload challenges often associated with cloud computing. Additionally, the Secure Hash Algorithm-3 (SHA-3) plays a crucial role in ensuring data integrity and is implemented for numerous applications in the IoT field. Therefore, integrating the SHA-3 accelerator into edge computing is essential. Moreover, recent studies about SHA-3 have primarily focused on achieving high performance and optimizing resource utilization for SHA-3. However, these studies have overlooked the crucial aspect of data transfer between the external memory and the hash function block, as transfer time plays a significant role. This paper proposes an efficient SHA-3 architecture designed for System-on-Chip (SoC) Field Programmable Gate Array (FPGA) to address the aforementioned challenges and be suitable for real edge computing. The architecture contains three key techniques. First, the harmony of padding and Direct Memory Access (DMA) for managing the data transfer process and enhancing performance efficiency based on Serial Input to Parallel Output (SIPO) and a barrel shifter. Secondly, implementing internal pipelining within the Round Function (RF) to reduce critical path delays and optimize resource utilization. Finally, designing four modes (SHA3-224, SHA3-256, SHA3-384, and SHA3-512) to cater to various applications. Our architecture is implemented and tested on the DE10-Standard Development Kit (Cyclone V SX SoC-5CSXFC6D6F31C6N), which is integrated into the FPGA and is controlled by a Dual-Core ARM Cortex-A9 processor. The result is up to 38.34 Gbps in throughput and 5.61 Mbps/ALM in efficiency for the RF computation, 28.02 Gbps in throughput, and 3.63 Mbps/ALM for the full proposed architecture.

The internal wave recognition algorithm in an ocean data buoy system can be used to realize the real-time and flexible observation of internal waves, but there is no accurate automatic recognition method. To meet the need for automatic, real-time, and reliable internal wave recognition, an automatic internal wave recognition algorithm has been proposed for a tightly profiled intelligent buoy system. The sea profile temperature data collected by the Bailong buoy system in the Andaman Sea in 2018 were used to train and test the internal wave recognition neural network model, which consists of two parts: feature extraction and feature classification. The experiment compares the long short-term memory network (LSTM), convolutional neural network (CNN) with different layers, and deep neural network (DNN) without a feature extraction network and adjusts the number of convolutional nuclei and convolutional strides to improve the feature extraction efficiency. Experiments show that the best results can be obtained when a CNN layer is used as the feature extraction network, the convolutional step length is 4, the number of convolutional kernels is 5. The recall reaches 95.31% and the precision is 97.53%. The internal wave identification delay of the algorithm is 5.0862 minutes, the number of parameters is 1593, and the number of calculations is 3024. The algorithm can be directly deployed to the ocean data buoy system to realize the demand for automatic, real-time and reliable internal wave identification at the buoy end.

The solutions of the radial Schrödinger equation for a pseudoharmonic potential and Kratzer potentials has been studied separately in the past. The Kratzer potential despite different reports, the basic theoretic quantity such as Fisher information has not been reported. In this study, the solution of the radial Schrödinger equation for the combination of the pseudoharmonic and Kratzer potentials in the presence of a constant-dependent potential is obtained using the concepts and formalism of the supersymmetric and shape invariance approach. The position expectation value and momentum expectation value are calculated employing the Hellmann-Feynman Theory. The expectation values are used to calculate the Fisher information for both the position and momentum spaces in both the absence and presence of the constant-dependent potential. The obtained results revealed that the presence of the constant-dependent potential leads to an increase in the energy eigenvalue, as well as in the position and momentum expectation values. The presence of the constant-dependent potential also increases the Fisher information for both position and momentum spaces. Furthermore, the product of the position expectation value and the momentum expectation value along with the product of the Fisher information, satisfies both the Fisher’s inequality and the Cramer-Rao’s inequality.

This report provides a comprehensive overview of occupational asthma and respiratory hypersensitivity, focusing on some chemicals used in the workplace Includes numerous case studies and research papers related to occupational exposure methacrylates, such as HEMA-HPMA, and respiratory hypersensitivity are discussed And the relationship is explored The book also examines asthma pathophysiology, emerging drug delivery systems used to treat asthma, and the potential of nanoparticles , dendrimers and micellar systems have to improve pulmonary drug delivery in detail The worldwide prevalence of asthma is highlighted, with higher rates in high-GDP countries. The book highlights the need to improve asthma diagnosis, treatment and biomarkers, particularly in rural and low-income countries where the disease is often underdiagnosed and inadequately treated, and discusses the role of inflammation in asthma, in particular secondary inflammation characterized by specific cytokines and inflammation cells In addition, the paper explores various drug delivery methods, such as parenteral and parenteral drugs, pressurized inhalers (pMDIs), dry powder inhalers ( DPIs), nebulizers, nanoparticles, liposomes, micellar systems, microparticles , dendrimers, and gene therapy . These systems aim to increase pulmonary delivery of drugs and improve clinical outcomes. The potential of dendrimer bilirubin-based nanoparticles and micellar systems in the treatment of asthma and lung inflammatory diseases, including asthma, has been discussed in summary, this paper provides an overview of occupational asthma and respiratory hypersensitivity, and this discussion highlights the association between methacrylate exposure and respiratory hypersensitivity.

The subject of the research is to Development of laser ablation method for Fabrication of surface acoustic wave sensors on quartz wafer, the target of the GQW – is to design Acoustic wave sensor by using laser ablation method. By using the surface acoustic wave theory to sense by the signal and using this physical phenomenon, We will design the sensor which transduce an input electrical signal into a mechanical wave which unlike an electrical signal, can be easily influenced by physical phenomena. The device then transducers this wave back into an electrical signal on the secondary terminal of the sensor. Changes in amplitude, phase, frequency, or time-delay between the input and output electrical signals can be used to measure the presence of the desired Our work in this part, especially the practical part like temperature, vibration ,etc. we design a combs on the waver of quartz to make like an electrode primary electrode & secondary electrode by putting coats of cuppers & vanadium on the waver and then using the fiber optic laser regime to design this combs to can able transfer the signal by ablation the most important here to use the regime of fiber optic laser then we using this sensor in any electronic circuit How we will select the suitable kind of laser to design, this is the most important part, and what it will be the diameter of that combs of secondary and primary , how much the value of the wave length to select the micro distant combs to avoid any inductance and interference for transferred signal , also take the benefit of using MEMS theory in our project.

This research, which focuses on wave energy generating technology, suggests a brand-new oscillating float-type wave energy conversion system that is appropriate for the offshore wave environment. To accurately model the device, a three-dimensional viscous numerical pool is created based on STAR-CCM+. The array-type power generation device is numerically simulated using theoretical analysis and numerical simulation, and the wave energy power generation device is arranged as double floats in the front and rear rows, representing triangular array type and rectangular array type, respectively. The triangular array type is a superior layout and can make greater use of marine resources, according to this paper's analysis of the hydrodynamic and power generation impacts of the three array types. The findings are meant to serve as a guide for engineering practice.

This paper presents an improved indoor localization system based on RF and ultrasonic signal which we named SNSH system. This system composes of a transmitter mounted in a mobile target, and a series of receiver nodes which are managed by a coordinator. By measuring Time Delay of Arrival (TDoA) of RF and ultrasonic signal from the transmitter, distance from target to receiver node is calculated and sent to the coordinator through CAN network, and all the information are gathered in PC to estimate 3D position of the target. Sine wave detector and dynamic threshold filter are applied to provide excellent accuracy of range measurement from TDoA result, and multilateration algorithms is realized to optimize coordinate determination accuracy. Specifically, Linear Least Square and Non-linear Least Square techniques are implemented to contrast their performances in target coordinate estimation. RF signal encoding/decoding time, time delay in CAN network and math calculating are carefully considered to ensure optimal system performance and get ready for field application. Experiments show that sine wave detector algorithm has greatly improved range measurement accuracy, with mean error at 2.2mm and maximum error at 6.7 mm, for distance below 5m. In addition, 3D position accuracy is greatly enhanced by multilateration methods, with mean error in position stay under 15mm, and 90% confident error values at 23mm for LLS, 20mm for NLS. Overall system update period has been verified in real system operation, with maximum rate at 25ms, and compared with other existing researches.

Western Anatolia comprises a vast amount of various volcanic successions spanning from Eocene to Upper Miocene periods. These units mainly display southward younging in broad sense and display large amounts of chemical variation that spanned from basalt to rhyolite. The southward younging of magmatism and chemical variations have been largely attributed to the retreat and roll-back of the Hellenic slab and the western escape of the Anatolian microplate. However, there is still a lack of high precision data to pinpoint the exact nature of the magmatism and lithospheric tectonics. In this contribution we investigated a poorly known region along the Western Anatolia along Manisa district called Karakılıçlı volcanic field. We investigated two different volcanic sections (Kalpakkaya and Çamlık hill) that display the best volcano-sedimentary features in terms of geochronology and geochemistry. Samples acquired from the bottom, middle and upper portions of these sections display Early-Middle Miocene ages of 17.64±0.20, 17.22±0.15, 16.16±0.17 and 16.36±0.13, 15.79±0.71 and 13.61±0.20 Ma respectively. The results indicate that the volcanism in the region generated by the melting of the mantle and/or lithospheric mantle by slab retreat and roll-back of the Hellenic slab and evolved in the shallow magma chambers/mushes by fractional crystallization, magma mixing and crustal assimilation.

Here we present an overview of speleothem δ18O records from South America, which mostly are available in the Speleothem Isotopes Synthesis and Analysis (SISAL_v1) database. South American tropical and subtropical δ18O time series are primarily interpreted as being driven by the amount effect and, consequently show the past history of the convection intensity of convergence zones such as the Intertropical Convergence Zone and the South America Monsoon System. We investigate past hydroclimate scenarios in South America related to the South American Monsoon System in three different time scales: Late Pleistocene, Holocene and the last two millennia. The precession driven insolation is the main driver of convective variability over the continent during the last 250 kyrs, including the Holocene period. However a dipole is observed between the west and east portions of the continent. Records located in the central region of Brazil appear to be weakly affected by insolation driven variability and more susceptible to the South Atlantic Convergence Zone. Cold episodic events in Northern Hemisphere increase the activity of the South American Monsoon System on all time scales, in turn increasing rainfall amounts in South America, as was documented during Heinrich events in the late Pleistocene and Bond events in the Holocene, as well as during the Little Ice Age.

In this paper, we investigated transducer placement strategies for detecting crack in primary aircraft structures using ultrasonic Structural Health Monitoring (SHM). The approach developed is for an expected damage location based on fracture mechanics, for example fatigue crack growth in a high stress location. To assess the performance of the developed approach, finite-element (FE) modelling of a damage tolerant aluminum fuselage has been performed by introducing an artificial crack at a rivet hole into the structural FE model and assessing its influence on the Lamb wave propagation, compared to a baseline measurement simulation. The efficient practical sensor position was determined from the largest change in area that is covered by reflected and missing wave scatter using an additive color model. Blob detection algorithms were employed in order to determine the boundaries of this area and to calculate the blob centroid. To demonstrate that the technique can be generalized, the results from different crack lengths and from tilted crack are also presented.

Mutations in the Neuroligin-3 (Nlgn3) gene are implicated in autism spectrum disorder (ASD) and gastrointestinal (GI) dysfunction but cellular Nlgn3 expression in the enteric nervous system remains to be characterised. We combined RNAScope in situ hybridization for Nlgn3 mRNA and immunofluorescence for cholinergic and VIP-expressing submucosal neurons, nitrergic and calretinin-containing myenteric neurons and glial cells. We measured Nlgn3 mRNA neuronal and glial expression via quantitative 3-dimensional image analysis. To validate dual RNAScope/immunofluorescence data, we interrogated available single cell RNA sequencing (scRNASeq) data to assess for Nlgn3, Nlgn1, Nlgn2 and their binding partners, Nrxn1-3, MGDA1 and MGDA2, in enteric neural subsets. Most submucosal and myenteric neurons expressed Nlgn3 mRNA. In contrast to other Nlgns and binding partners, Nlgn3 was strongly expressed in enteric glia, suggesting a role for Neuroligin-3 in mediating enteric neuron-glia interactions. The autism-associated R451C mutation reduces Nlgn3 mRNA expression in cholinergic but not VIPergic submucosal neurons. In the myenteric plexus, Nlgn3 mRNA levels are reduced in calretinin and NOS labelled neurons and S100ß labelled glia. We provide a comprehensive cellular profile for neuroligin-3 expression in ileal neuronal subpopulations of mice expressing the R451C autism-associated mutation in Nlgn3, which may contribute to the understanding of the pathophysiology of GI dysfunction in ASD.

The Wave Mode (WM) is a unique imaging mode of spaceborne synthetic aperture radar (SAR), which is dedicatedly designed for global ocean surface wave observations. Since it was firstly achieved in the ERS-1/SAR satellite starting from 1991, the WM data over global oceans have been continuously acquired by the ESA’s SAR instruments onboard the satellites of ERS-2 (1997 – 2011), ENVISAT (2002 – 2012), Sentinel-1A(2014--)/1B(2016--) and the Chinese GaoFen-3 SAR (2016--), for nearly 30 years. Therefore, spaceborne SAR WM data have been a ‘big data’, which however, has not been widely exploited for global ocean wave measurements. In this study, we demonstrate its application on global ocean wave measurements based on the ten-year Advanced SAR (ASAR) WM data.

The three dimensional conformable time fractional Kadomtsev-Petviashvili and the conformable time fractional modified Kawahara equations are solved by implementing the Kudryashov's procedure. The corresponding wave transformation reduces both equations to some ODEs. Balancing the nonlinear and the highest order derivative terms gives the structure of the solutions in the finite series form. The useful symbolic tools are used to solve the resultant algebraic systems. The solutions are expressed in explicit forms.

Wave steepness is presented as an extension and a valuable add-on to the conventional set of sea state parameters retrieved from satellite altimetry data. Following physical model based on recent advances of weak turbulence theory wave steepness is estimated from directly measured spatial gradient of wave height. In this way the method works with altimetry trajectories rather than with point-wise data. Moreover, in contrast to widely used parametric models this approach provides us with instantaneous values of wave steepness and period. Relevance of single-track estimates of wave steepness (period) is shown for wave climate studies and confirmed by a simple probabilistic model. The approach is verified via comparison against buoy and satellite data including crossover points for standard 1 second data of Ku-band altimeters. High quality of the physical model and robustness of the parametric ones are examined in terms of global wave statistics. Prospects and relevance of both approaches in the ocean wave climate studies are discussed.

In this paper, we succeed to discover the new exact wave solutions to the truncated M-fractional complex three coupled Maccari’s system by utilizing the Sardar sub-equation scheme. The obtained solutions are in the form of trigonometric and hyperbolic forms. These solutions have many applications in nonlinear optics, fiber optics, deep water-waves, plasma physics, mathematical physics, fluid mechanics, hydrodynamics and engineering where the propagation of nonlinear waves is important. Achieved solutions are verified with the use of Mathematica software. Some of the achieved solutions are also described graphically by 2-dimensional, 3-dimensional and contour plots with the help of Maple software. The gained solutions are helpful for the further development of concerned model. Finally, this technique is simple, fruitful and reliable to handle the nonlinear FPDEs.

Background: Most sepsis patients died during their first episode and the long-term survival post discharge was low. Major adverse cardiovascular events and repeated infections were regarded as the major causes in such conditions. No definite medications were proven to effectively improve the long-term outcome. We aimed to examine the benefit of statins on the long-term outcome of survived sepsis patients. Methods: Between 1999 and 2013, a total of 220,082 patients with the first episode of sepsis hospitalization were included and 134,448 ones (61.09%) survived to discharge. The survived patients who subsequently had statins use of >30 cumulative defined daily doses (cDDDs) post discharge were defined as the statin users. After propensity score matching of 1:5, a total of 7,356 and 36,780 survived patients were retrieved as the study (statin-users) and comparison cohort (non-statin users), respectively. The main outcome was the long term survival post discharge. HR with 95% CI was calculated using the Cox regression model to evaluate the effectiveness of statins with further stratification analyses according to cDDDs. Results: The study cohort, that is, the statin users had an adjusted HR of 0.29 (95% CI, 0.27-0.31) in long term mortality rate compared with the comparison cohort. For statin users with the cDDDs of 30–180, 180–365, and >365, the adjusted HRs were 0.32, 0.22, and 0.16, respectively, (95% CI, 0.30-0.34, 0.19-0.26, and 0.12-0.23, respectively) compared with the non-statin users (defined as statins use <30 cDDDs post discharge), and the P for trend <.0001. In the sensitivity analysis, after excluding the survived patients who died within three and six months post discharge, the adjusted HR of statins use remained significant (0.35, 95% CI 0.32-0.37 and 0.42, 95% CI 0.39-0.45, respectively). Conclusions: Statins decreased the long-term mortality post sepsis. Further randomized control trial deserved to be conducted to confirm this observation.

High-resolution wave measurements at intermediate water depth are required to improve coastal impact modeling. Specifically, such data sets are desired to calibrate and validate models, and broaden the insight on the boundary conditions that force models. Here, we present a wave data set collected in the North Sea at three stations in intermediate water depth (6-14~m) during the 2021/2022 storm season as part of the RealDune/REFLEX experiments. Continuous measurements of synchronized surface elevation, velocity and pressure were recorded at 2-4~Hz by Acoustic Doppler Profilers and an Acoustic Doppler Velocimeter for a 5~month duration. Time series were quality-controlled, directional-frequency energy spectra were calculated, and common bulk parameters were derived. Measured wave conditions vary from calm to energetic with 0.1-5.0~m sea-swell wave height, 5-16~s mean wave period and W-NNW direction. Nine storms, i.e. wave height beyond 2.5~m for at least six hours, were recorded including the triple storms Dudley, Eunice and Franklin. This unique data set can be used to investigate wave transformation, wave nonlinearity and wave directionality for higher and lower frequencies (e.g. sea-swell and infragravity waves) to compare with theoretical and empirical descriptions. Furthermore, the data can serve to force, calibrate and validate models during storm conditions.

The process of shock wave focusing can make the strength of shock waves be continuously accumulated and turned into detonation wave in Pulse Detonation Engine (PDE). However, its effective application needs the inlet jets be in high temperature and velocity, which is difficult to be satisfied under certain conditions. Therefore, in this paper, metal magnesium assisted detonation initiation is proposed and the effect of magnesium particle addition on the shock wave focusing process in a kerosene-fueled PDE with cavity configuration is investigated through numerical simulation. The result showed that when the temperature of the premixed fuel/air jets injected in opposite direction was set as 650 K, the collision of leading shock waves on the central axis was the main source of energy deposition and the shock wave focusing could make the detonation be initiated in the cavity. When the temperature of jets is reduced to 550 K, fuel ignition and detonation could not be achieved through shock wave focusing. Then adding metal magnesium particles into the combustor made the energy deposition be enhanced and the detonation be induced. The diffusion of metal particles can significantly change the structure, motion, merging and dissipation of vortices in the flow field. Generally, the shock wave focusing process is basically not affected with metal particles injection. Therefore, this method can be successfully employed for detonation initiation in the cavity when the fuel/air premixed jet temperature is not high for PDE.

The purpose of this work is to study Rossby wave parameters in total ozone over Arctic in 2000–2021. We consider the averages in the January–March period, when stratospheric trace gases (including ozone) in sudden stratospheric warming events are strongly disturbed by planetary waves. To characterize the wave parameters, we analyzed ozone data at the latitudes of 50° N (the sub-vortex area), 60° N (the polar vortex edge) and 70° N (inner region of the polar vortex). Total ozone column (TOC) measurements during 22-year time interval were used from Total Ozone Mapping Spectrometer (TOMS) / Earth Probe and Ozone Mapping Instrument (OMI) / Aura satellite observations. The total ozone zonal distribution and variations in the parameters of the Fourier spectral components with zonal wave numbers m = 1–5 are presented. Daily and interannual variations in TOC, amplitudes and phases of spectral wave components, and linear trends of the quasi-stationary wave 1 (QSW1) amplitudes are discussed. The positive TOC peaks inside the vortex in 2010 and 2018 alternate with negative ones in 2011 and 2020. The latter TOC anomalies correspond to severe depletion of stratospheric ozone over the Arctic in the strong vortex conditions due to anomalously low activity of planetary waves. Variations in TOC in sub-vortex region exhibit the statistically significant negative trend –4.8±5.4 DU decade–1 in QSW1 amplitude, while the trend is statistically insignificant at the vortex edge region due to increased TOC variability. Processes associated with polar vortex dynamics are discussed, including quasi-stationary vortex asymmetry and quasi-circumpolar migration of the wave-1 phase at the vortex edge.

The enhancement of Fusarium head blight (FHB) resistance is one of the best options to reduce mycotoxin contamination in wheat. This study has aimed to verify that the genotypes with high tolerance to deoxynivalenol could guarantee an overall minimization of the sanitary risk, by evaluating the contamination of regulated, modified and emerging mycotoxins on durum wheat cvs with different degrees of FHB susceptibility, grown under different meteorological condi-tions, in 8 growing seasons in North-West Italy. The years which were characterized by frequent and heavy rainfall in spring, were also those with the highest contamination of deoxynivalenol, zearalenone, moniliformin and enniatins. The most FHB resistant genotypes resulted in the lowest contamination of all the mycotoxins but showed the highest deoxyniva-lenol-3-glucoside/deoxynivalenol ratio and moniliformin/deoxynivalenol ratio. An inverse re-lationship between the amount of deoxynivalenol and the deoxyniva-lenol-3-glucoside/deoxynivalenol ratio was recorded for all the cvs and all the years. Converse-ly, the enniatins/deoxynivalenol ratio had a less intense relationship with cv tolerance to FHB. In conclusion, even though the more tolerant cvs, showed higher relative relationships between modified/emerging mycotoxins and native/target mycotoxins than the susceptible ones, they showed lower absolute levels of contamination of both emerging and modified mycotoxins.

Public health practices including handwashing and vaccinations help reduce the spread and impact of infections. Nevertheless, the global burden of infection is high, and additional measures are necessary. Acute respiratory tract infections, for example, are responsible for approximately 2.65 million deaths per year. The role nutrition plays in supporting the immune system is well-established. A wealth of mechanistic and clinical data show that vitamins, including vitamins A, B6, B12, C, D, E, and folate; trace elements, including zinc, iron, selenium, magnesium, and copper; and the omega-3 fatty acids eicosapentaenoic acid and docosahexaenoic acid play important and complementary roles in supporting the immune system. Inadequate intake and status of these nutrients are widespread, leading to a decrease in resistance to infections and as a consequence an increase in disease burden. Against this background the following conclusions are made: 1) Supplementation with the above micronutrients and omega-3 fatty acids is a safe, effective, and low-cost strategy to help support optimal immune function; 2) Supplementation above the RDA, but within recommended upper safety limits, for specific nutrients such as vitamins C and D is warranted; and 3) Public health officials are encouraged to include nutritional strategies in their recommendations to improve public health.

According to Quantum Mechanics a narrow wave-package of the center of mass of macroscopic objects, due to their heavy mass, remains stable over astronomical times. However Quantum Mechanics allows and energetically even prefers largely smeared out c.m. states that never been seen. Why is this the real state of the world we know? Does it suggest a micro-macro threshold with different theoretical descriptions?

Computational Fluid Dynamics (CFD) simulations, based on Reynolds Averaged Navier Stokes (RANS) models, are a useful tool for a wide range of coastal and offshore applications, providing a high fidelity representation of the underlying hydrodynamic processes. Generating input waves in the CFD simulation is performed by a numerical wavemaker (NWM), with a variety of different NWM methods existing for this task. While NWMs, based on impulse source methods, have been widely applied for wave generation in depth averaged, shallow water models, they have not seen the same level of adoption in the more general RANS based CFD simulations, due to difficulties in relating the required impulse source function to the resulting free surface elevation for non-shallow water cases. This paper presents an implementation of an impulse source wavemaker, which is able to self-calibrate the impulse source function to produce a desired wave series in deep or shallow water at a specific point in time and space. Example applications are presented, for a numerical wave tank (NWT), based on the opensource CFD software OpenFOAM, for wave packets in deep and shallow water, highlighting the correct calibration of phase and amplitude. Also, the suitability for cases requiring very low reflection from NWT boundaries is demonstrated. Possible issues in the use of the method are discussed and guidance for good application is given.

A numerical study for the effect of crest width, breaking parameter and trunk permeability on hydrodynamics and flow behavior in the vicinity of rubble-mound, permeable, zero-freeboard breakwaters (ZFBs) is presented. The modified two dimensional Navier-Stokes equations for two-phase flows in porous media with a Smagorinsky model for the subgrid scale stresses were solved numerically. An immersed-boundary/level-set method was used. The numerical model was validated for the cases of wave propagation over a submerged impermeable trapezoidal bar and over a low-crested permeable breakwater. Five cases of breakwaters were examined, and the main results are: (a) The size of the crest width, B, does not notably affect the wave reflection, vorticity and currents in the seaward region of ZFBs, while wave transmission, currents in the leeward side, and mean overtopping discharge, all decrease with increasing B. A non-monotonic behavior of the wave setup is also observed. (b) As the breaking parameter decreases, wave reflection, transmission, currents, mean overtopping discharge, and wave setup decrease. This observation is also verified by relevant empirical formulas. (c) As the ZFB trunk permeability decreases, an increase of the wave reflection, currents, wave setup, and a decrease of wave transmission and mean overtopping discharge is observed.

A Shape Memory Alloy (SMA) enabled Overtopping Wave Energy Converter (OWEC) that maximizes its overtopping discharge, and thus energy output under different wave conditions is presented. Among all the parameters affecting the overtopping discharge rate, the crest freeboard height is the most influential one to control the overtopping discharge rate and the stored overtopping volume behind it. Currently, all the OWEC crest freeboard heights are fixed by design to maximize the discharge rate on one particular sea state. In the present study, we show that the SMA can adjust the crest freeboard height through a control system based on the sea state and achieve an optimal overtopping discharge rate. A scaled OWEC model is built in the lab with its crest freeboard height controlled by springs made of SMA. The length (and thus tension) of the springs is controlled by temperature changes by changing the passing current through the springs. By adjusting the length of the springs based on the incoming wave condition, we adjust the freeboard to an optimal height known to generate a maximum overtopping discharge rate for energy conversion. This smart material-enabled design can maximize the overtopping discharge and thus the output power of the OWEC under various wave conditions. Furthermore, the simplicity of using SMA springs as the actuator leads to the minimum number of moving mechanical parts, which can remarkably decrease maintenance costs. As the proof of concept, two types of tests are conducted in the laboratory using the same OWEC model under several random wave trains generated from spectra with different significant wave heights - one type with a fixed crest freeboard height and the other type featuring the adjustable crest freeboard height controlled by the springs. The substantial increase of harvested output power in the OWEC with the adjustable crest freeboard height may pave the way for more efficient wave energy conversion systems.

Background-The outbreak of COVID-19 pandemic has affected the global economy from its starting. Indian economy is also affected by the pandemic and experienced a lot of economic damages. India has become the global hotspot of COVID-19 during the second wave of the pandemic and recorded the second-highest position in terms of positivity rate after China. The present study attempts to analyze the economic issues that emerged in the first and second waves of the pandemic in India. Method/Approach-There is no econometric tools or analytical models used in the present study. This study attempts to evaluate the two research questions which are formed on the basis of some previous studies by various organizations and researchers. The research questions are as follow, First, what are the sectors those are primarily affected at the time of the first COVID-19 outbreak? Second, which economic issues and impacts emerged in the second wave of the pandemic? Results/ Findings-From the study, it is found that the second wave of COVID-19 is not much affected by the Indian economy. At this time, no nationwide lockdown was announced by the Government. But so, it was much severe in the time of the first wave of COVID-19. Many sectors were affected by the pandemic like agriculture, MSMEs, Tourism, etc., and these resulted in substantial unemployment problems in the economy. The study is trying to analyze these problems and concluding it with a few policy recommendations for the economy of India.

Refraction of an oblique shock wave on a tangential discontinuity dividing two gas flows with different properties is considered. It is shown that its partial reflection occurs excepting of geometrical diffraction of an oblique shock. Another oblique shock, expansion wave or weak discontinuity that coincides with Mach line, can act as a reflected disturbance. This study focuses on relationships which define the type of reflected discontinuity and its parameters. Domains of existence of various shock-wave structures with reflected disturbances of two types and boundaries between them are defined. The domains of parameters with one or two solutions exist for the characteristic refraction. Conditions of the regular refraction and the Mach refraction are formulated, and boundaries between those two refraction types are defined for various types of gases. Refraction phenomena in various engineering problems (hydrocarbon gaseous fuel and its combustion products, diatomic gas, fuel mixture of oxygen and hydrogen etc.) are discussed.

We suggest that momentum should be redened in order to help make physics more consistent and more logical. In this paper, we propose that there is a rest-mass momentum, a kinetic momentum, and a total momentum. This leads directly to a simpler relativistic energy momentum relation. As we point out, it is the Compton wavelength that is the true wavelength for matter; the de Broglie wavelength is mostly a mathematical artifact. This observation also leads us to a new relativistic wave equation and a new and likely better QM. Better in terms of being much more consistent and simpler to understand from a logical perspective.

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.

An interesting physical phenomenon was recently observed when a fresh-water basin is covered by a thin ice film that has properties similar to that of a rubber membrane. Surface waves can be generated under the action of wind on the air-water interface that contains an ice film. The modulation property of hydro-elastic waves (HEWs) in deep water covered by thin ice film blown by the wind with a uniform vertical profile is studied here in terms of the air-flow velocity versus a wavenumber. The modulation instability of HEWs is studied through the analysis of coefficients of the nonlinear Schrödinger (NLS) equation with the help of the Lighthill criterion. The NLS equation is derived using the multiple scale method in the presence of airflow. It is demonstrated that the potentially unstable hydro-elastic waves with negative energy appear for relatively small wind speeds, whereas the Kelvin–Helmholtz instability arises when the wind speed becomes fairly strong. Estimates of parameters of modulated waves for the typical conditions are given.

Access to nasopharyngeal swabs for sampling remain a bottleneck in some regions for COVID-19 testing. This study develops a distributed manufacturing solution using only an open source manufacturing tool chain consisting of two types of open source 3-D printing and batch UV curing, and provides a parametric fully free design of a nasopharyngeal swab. The swab was designed using parametric OpenSCAD in two components (a head with engineered break point and various handles), which has several advantages: i) minimizing print time on relatively slow SLA printers, ii) enabling the use of smaller print volume open source SLA printers, iii) reducing the amount of relatively expensive UV resin, and iv) enabling production of handle on more accessible material extrusion 3-D printers. A modular open source UV LED box was designed, fabricated for $45 and tested for batch curing. Swabs can be fabricated for $0.06-$0.12/swab. The results of the mechanical validation tests showed that the swabs could withstand greater forces than would be expected in normal clinical use. The swabs were also able to absorb a significant amounts of synthetic mucus materials and passed abrasion and handling tests. The results show the open source swab are promising candidates for clinical trials.

A novel effective vibrational mode was discovered in the conventional transducer with an array of orthogonal (square) regular piezoelectric rods in 1-3 piezocomposite, containing the damping backing and front matching layers. The operational resonance in the structure was determined as the Surface Acoustic Wave (SAW) on the backing boundary excited by the adjacent piezo-rods, with its frequency typically near 3 times lower the fundamental half-lambda conventional piezocomposite resonance. Pulse-echo sensitivity and transmitting sound-pressure-level (SPL) in air showed that the signal strength is roughly comparable to the industrial similar air transducers at the frequency range 100…700 kHz, where at these frequencies the lateral and longitudinal piezoelement dimensions in the conventional transducer design are typically close to each other causing interference with unwanted coupling modes. As was determined theoretically and proved in experiments, the backing SAW resonance effect in the transducer performance is inherent just to the regular periodic 1-3 piezocomposite structure, and does occur neither with randomly located/oriented piezo-rods, nor in the homogeneous piezo-plate at least with the same lateral cross-section as the connected to it backing. The purpose of the article is to investigate a newly discovered operational vibrational mode of a SAW type in 1-3 regular piezocomposite, other than piezoelectric resonance. The investigated phenomena can improve the transceiver sensitivity, bandwidth, providing lower drive voltage, and smaller and lighter weight ultrasonic transducers. Based on the piezocomposites with thickness’ 1…1.5 mm (rod resonance near 2…3 MHz), pillar width 0.2…0.8 mm, kerf width 0.1…0.4 mm, the transceivers with an operating frequency from 140 kHz to 650 kHz were designed and fabricated with a conventional backing of a mixture of high-density tungsten powder and epoxy, and a matching layer of a mixture of low-density glass bubbles and epoxy. Experimental evaluation of their acoustical performance showed expected characteristics suitable for practical applications.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r&gt;0.90) and peri-urban (HWM, HWA, r&gt;0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Knowledge of wave climate is essential for efficient management of the world's coastal areas. Senegal is a relevant case given its high coastal vulnerability to energetic wave conditions. This study investigates wave climates along the coastal zone of Senegal based on a new high-resolution hindcast covering the period 1980-2021. This study evaluates the average, seasonal and extreme values for the wave significant heights (Hs), periods (Tm02/Tp) and mean directions (DIR). In boreal Winter, the wave climate is dominated by swells coming from the North-Atlantic lows, while in boreal Summer, the Southern Coast (from Dakar to Casamance) is exposed to swells generated in the South-Atlantic Ocean. Throughout their refraction around Dakar Peninsula, NW swells rotate by ~100° from NW to SW, while their Hs is roughly halved when reaching the Southern Coast of Senegal. Over the studied period, trends in Hs are weak (~0.6 cm.decade-1) on the Northern Coast, double on the Southern coast (~1.2 cm.decade-1), mostly due to an increase during boreal Summer (2 cm.decade-1). The wave periods show weak trends (~0.05 s.decade-1) and DIRs show weak counterclockwise rotation (-1°.decade-1). These trends are explained by the main climate modes of the Atlantic Ocean (NAO/EA during Winter, SAM during Summer) and are important for future research and long-term monitoring of the Senegalese Coast.

Wave energy converter (WEC) arrays deployed in coastal regions may create physical disturbances potentially resulting in environmental stresses. Presently, limited information is available on the nature of these physical disturbance or the resultant effects. A quantitative Spatial Environmental Assessment Tool (SEAT) for evaluating potential effects of wave energy converter (WEC) arrays on nearshore hydrodynamics and sediment transport is presented for the central Oregon coast (USA) through coupled numerical model simulations of an array of WECs. Derived climatological wave conditions were used as inputs to the model to allow for the calculation of risk metrics associated with various hydrodynamic and sediment transport variables such as maximum shear stress, bottom velocity, and change in bed elevation. The risk maps provided simple, quantitative, and spatially-resolved means of evaluating physical changes in the vicinity of a hypothetical WEC array in response to varying wave conditions. Near-field risk of sediment mobility was determined to be moderate in the lee of the densely spaced array, where the potential for increased sediment deposition could result in benthic habitat alteration. Modifications to the nearshore sediment deposition and erosion patterns were observed near headlands and topographic features, which could have implications for littoral sediment transport. The results illustrate the benefits of a risk evaluation tool for facilitating coastal resource management at early market marine renewable energy sites.

Background: Amyloid beta peptides (Aβ) have been identified as the main pathogenic agents in Alzheimer’s disease (AD). Soluble Aβ oligomers, rather than monomer or insoluble amyloid fibrils, show membrane-binding capacity to red blood cells (RBCs) and trigger several morphological and functional alterations in RBCs that can result in impaired oxygen transport and delivery. Since bioactive lipids have been recently proposed as potent protective agents against Aβ toxicity, we investigated the role of sphingosine-1-phosphate (S1P) in signaling pathways involved in the mechanism underlying ATP release in Aβ-treated RBCs. Methods: In RBCs following different treatments, ATP, 2,3 DPG, cAMP levels, and caspase 3 activity were determined by spectrophotometric and immunoassay. Results: S1P rescued the inhibition of ATP release from RBCs triggered by Aβ through a mechanism involving caspase-3 and restoring 2,3 DPG and cAMP levels within the cell. Conclusions: These findings reveal the molecular basis of S1P protection against Aβ in RBCs and suggest new therapeutic avenues in AD.

This work addresses the problem of automatic head pose estimation and its application in 3D gaze estimation using low quality RGB--D sensors without any subject cooperation or manual intervention. The previous works on 3D head pose estimation using RGB--D sensors require either an offline step for supervised learning or 3D head model construction which may require manual intervention or subject cooperation for complete head model reconstruction. In this paper, we propose a 3D pose estimator based on low quality depth data, which is not limited by any of the aforementioned steps. Instead, the proposed technique relies on modeling the subject's face in 3--D rather than the complete head, which in turn, relaxes all of the constraints with the previous works. The proposed method is robust, highly accurate and fully automatic. Moreover, it does not need any offline step. Unlike some of the previous works, the method only uses depth data for pose estimation. The experimental results on the Biwi head pose database confirm the efficiency of our algorithm in handling large pose variations and partial occlusion. We also evaluate the performance of our algorithm on IDIAP database for 3D head pose and eye gaze estimation.

In 1935 Einstein, Podolsky, and Rosen (EPR) studied general entangled states in the two photon experiment and pointed out the contradiction between local realism and the completeness of quantum mechanism. Most of the EPR experiments in recent years are based on the detection of polarization correlations of optical photons between spatially separated photon channels, some of which are split and directed to two spatially separated Michelson interferometers. Later, the two arms of Michelson interferometers are replaced by dual-channel Fabry-Perot (F-P) interferometry enabling precise analysis of the energy-time entanglement between a pair of photons. On the other hand, F-P type detectors on gravitational radiation have caught dozens of gravitational wave (GW) events successfully. This paper proposes a combined experiment of EPR and GW, exhibiting whether the coincident rate of EPR is modulated by GW induced change of cavity length or not. Such an experiment could test the coupling of quantum mechanics and general relativity for the first time, and be a useful tool to explore the nature of quantum gravity.

Build a special identical equation, use its calculation characters to prove and search for solution of any odd converging to 1 equation through (*3+1)/2^k operation, change the operation to (*3+2^m-1)/2^k, and get a solution for this equation, give a specific example to verify. Thus prove the Collatz Conjecture is true. Furthermore, analysis the sequences produced by iteration calculation during the procedure of searching for solution, build a weight function model, prove it decrease progressively to 0, build a complement weight function model, prove it increase to its convergence state. Build a (*3+2^m-1)/2^k odd tree, prove if odd in (*3+2^m-1)/2^k long huge odd sequence can not converge, the sequence must outstep the boundary of the tree after infinite steps of (*3+2^m-1)/2^k operation.

Propagation of electromagnetic (EM) waves inside and on the surface of the human body is the subject of active research in area of biomedical applications. This research area is the basis for wireless monitoring of biological object parameters and characteristics. Much attention has been paid to radio-frequency identification systems, which are intended for biomedical applications. Solutions to the following problems are crucial to achieve the stated goals in the area of wireless monitoring: EM wave propagation inside regular and multilayer biological media, through the interface between different media, and on-body surface wave propagation. The biological object monitoring is based on a consideration of the followingprocesses: a) propagation of the EM wave in a biological medium considered as the dielectric with a high dielectric permittivity and substantial conductivity; b) penetration of the EM wave through the biological medium–air interface (wave reflection and refraction); c) propagation of the EM wave in a multi-layer biological medium; d) propagation of the EM wave along the plane or curved surface of biological objects.

A new approach was presented in this study to simulate a stable atom along with subatomic particles in it. Subatomic particles in an atom are treated as conventional particles, exhibiting attraction and repulsion between them, giving a stable atom simulation. This new approach leads to developing new potentials for subatomic particles to simulate a stable atom. Subatomic particle dynamics (SPD) simulations were developed for within-atom simulations that give a stable atom structure for infinite time and provide many insights into electron trajectories and atom properties like energies and radius of the atom. The effect of protons and neutrons movement in the nucleus on electron trajectories was captured in SPD. Hydrogen and Carbon atom SPD were reported in this study. The Pilot-wave theory was implemented in this study to simulate the wave nature of subatomic particles in an atom. Electrons motion was guided by the interference pattern produced by the electron’s aether medium waves in SPD. SPD was implemented on molecules, resulting in a stable molecular structure giving insights into electron trajectories shared by multiple atoms.

Mammography is the gold standard for breast cancer screening and diagnostic imaging; however, there is an unmet clinical need for complementary methods to detect lesions not characterized by mammography. Far-infrared 'thermogram' breast imaging can map the skin temperature, and signal inversion with components analysis can be used to identify the mechanisms of thermal image generation of the vasculature using dynamic thermal data. This work focuses on using dynamic infrared breast imaging to identify the thermal response of the stationary vascular system and the physiologic vascular response to a temperature stimulus affected by vasomodulation. The recorded data is analyzed by converting the diffusive heat propagation into a virtual wave and identifying the reflection using component analysis. Clear images of passive thermal reflection and thermal response to vasomodulation were obtained. Validation of this proposed paradigm through further clinical exploration may demonstrate clinical utility for the IR modality in diagnostic imaging, offering a potential solution to the current unmet clinical need.

The research examines the relationship between self-rated health situation and personal percep-tion of heat waves, and how social linkage of communities would be a moderator variable in residents’ perception of heat waves in Taiwan. This study uses the questionnaire conducted by Sinica “Responsive Capacity under Heat Wave: The Perspectives of the Locals”(2019), using OLS method for estimating the unknown parameters in multiple regression model. The author finds that the correlation of self-rated health situation and perception toward heat is significantly posi-tive. Also, social linkage in communities affects strongly as a moderator variable: While the sat-isfaction to with their community could reduce negative reaction to heat, contacts with neighbors could increase possibility people feel uncomfortable in high-temperature situation. This study ex-hibits the effects of social environment on community, and expects further related researches or practices to strengthen capability to resist heat wavesƒ for Taiwanese residents.

Spaceborne altimeters are an important data source for obtaining global sea surface wind speeds (U10). Although many altimeter U10 algorithms have been proposed and they perform well, there is still room for improvement. In this study, the data from ten altimeters were collocated with buoys to investigate the error of the altimeter U10 retrievals. The U10 residuals were found to be significantly dependent on many oceanic and atmospheric parameters. Because these oceanic and atmospheric parameters are inter-correlated, an asymptotic strategy was used to isolate the impact of different parameters and establish a neural-network-based correction model of altimeter U10. The results indicated that significant wave heights and mean wave periods are effective in correcting U10 retrievals, probably due to the tilting modulation of long-waves on the sea surface. After the wave correction, the root-mean-square error of the retrieved U10 was reduced from 1.42 m/s to 1.24 m/s and the impacts of thermodynamic parameters, such as sea surface (air) temperate, became negligible. The U10 residuals after correction showed that the atmospheric instability can lead to errors on extrapolated buoy U10. The buoy measurements with large air-sea temperature differences need to be excluded in the Cal/Val of remotely sensed U10.

Ageing is associated with a decline in both Nrf2 activity and DNA repair efficiency, leading to the accumulation of DNA damage and an increased risk of cancer. Understanding the mechanisms behind the increased level of damaged DNA during ageing is crucial for developing interventions to mitigate age-related cancer risk and improve overall health in older individuals. (Poly)phenols are plant-derived bioactive compounds that undergo metabolism into simpler phenolic catabolites following ingestion. While these compounds have been associated with various health benefits, further analysis of their bioavailable catabolites is necessary. To this end, four phenolic catabolites derived from colonic microbiota were investigated for their ability to reduce DNA damage in response to oxidative challenge and modulate the Nrf2-Antixoidant Response Element pathway. Normal and adenocarcinoma colonocyte cell lines (CCD 841 CoN, & HT29 respectively) were exposed to sub cytotoxic concentrations (>10 µM,) of hydroxylated (4-hydroxybenzoic acid, 3-(3’-hydroxyphenyl) propionic acid) and non-hydroxylated (benzoic acid or 3-phenylpropionic acid) phenolic acids. Using the COMET assay, each catabolite demonstrated significant (p<0.001) geno-protective activity, albeit with varying potency. They also significantly modulated expression of key genes in the Nrf2-ARE pathway, including Nrf2, Heme oxygenase-1 (HO-1), and NAD(P)H dehydrogenase quinone 1 (NQO1). Hydroxylation of the phenolic acids appeared to have a limited effect with respect to bioactivity. Overall, the colon derived phenolic metabolites, when assessed at physiologically relevant concentrations, reduced DNA damage in both normal and adenocarcinoma colonic cells in response to oxidative challenge, mediated – at least in part via upregulation of the Nrf2-ARE pathway.

Directional protective relaying based on amplitude comparison of traveling wave on continuous co-phase auto-transformer(AT) power transmission system was proposed. Phase-model transformation is used for decoupling transient fault signals and get aerial mode component. The forward and backward traveling wave are obtained by calculating aerial mode component, then the intrinsic mode function(IMF) components can be obtained through Variational Mode Decomposition(VMD), the module maxima are obtained through calculating the IMF components. The fault direction is determined by the ratio of fault components. If two faults relays at the ends of electric traction networks detect a fault to be in the forward direction, the fault occurred in the internal area, the protection would operate properly. The simulation tests indicate that the protection scheme is feasible, and the proposed protection method can discriminate internal faults from external faults under various fault types, and its performances are immune to fault initial angle, ground resistance, etc.

Electrifying off-grid and isolated islands in the Philippines remains one of the challenges that hinders community development. One of the solutions seen to ensure energy security, expand energy access and promote a low carbon future in this isolated islands is the use of renewable energy sources. This study wishes to determine the nearshore wave energy resource during monsoon seasons in Cuyo Island using a 40-year wave hindcast and 9-year on-site wind speed data to develop high resolution wave energy model using SWAN wave model, and assessed its annual energy production through matching with wave energy devices. Results shows that average significant wave height (Hs), peak period (Tp) and wave power density (Pd) during northeast monsoon are Hs = 1.35 m, Tp = 4.79 s and Pd = 4.05 kW/m respectively, while southwest monsoon which is sheltered by the mainland resulted to a lesser outcome, Hs = 0.52 m, Tp = 3.37 s and Pd = 0.34 kW/m. While the simulated model was observed to overestimate the wave energy resource (Bias = 0.398, RMSE = 0.54 and SI = 1.34), it has a strong relationship with the observed values (average r = 0.9). Its annual energy production is highest at Station 5, with AEPWaveBouy = 43.761 MWh, AEP-Pelamis = 216.786 MWh and AEPWave Dragon = 2462.66 MWh. At present, the minimum requirement for a wave energy development to be feasible is 5 kW/m, which in this case, Cuyo Island falls short, but with the continuous evolution of wave energy converters, applications on milder re-sources will soon materialized.

Extracorporeal shock wave therapy (ESWT) is a safe and effective treatment option for various pathologies of the musculoskeletal system. Many studies addressed the molecular and cellular mechanisms of action of ESWT. However, no uniform concept could be established in this matter until now. We performed a systematic review of the effects of exposure of musculoskeletal tissue to extracorporeal shock waves (ESWs) reported in the literature. The key results were as follows: (i) compared to the effects of many other forms of therapy, the clinical benefit of ESWT does not appear to be based on a single mechanism; (ii) different tissues respond to the same mechanical stimulus in different ways; (iii) just because a mechanism of action of ESWT was described in a study does not automatically mean that this mechanism was relevant to the observed clinical effect; (iv) focused ESWs and radial ESWs seem to act in a similar way; and (v) even the most sophisticated research into the effects of exposure of musculoskeletal tissue to ESWs cannot substitute clinical research in order to determine the optimum intensity, treatment frequency and localization of ESWT.

We consider the developed turbulence of capillary waves on shallow water. Analytic theory shows that an isotropic cascade spectrum is unstable with the respect to small angular perturbations, in particular, to spontaneous breakdown of the reflection symmetry and generation of nonzero momentum. By computer modeling we show that indeed a random pumping, generating on average zero momentum, produces turbulence with a nonzero total momentum. A strongly anisotropic large-scale pumping produces turbulence whose degree of anisotropy decreases along a cascade. It tends to saturation in the inertial interval and then further decreases in the dissipation interval. Surprisingly, neither the direction of the total momentum nor the direction of the compensated spectrum anisotropy is locked by our square box preferred directions (side or diagonal) but fluctuate.

The signal-to-noise ratio (SNR) data is part of the global navigation satellite systems (GNSS) observables. In a marine environment, the oscillation of the SNR data can be used to derive reflector heights. Since the attenuation of the SNR oscillation is related to the roughness of the sea surface, the significant wave height (SWH) of the water surface can be calculated from the analysis of the attenuation. The attenuation depends additionally on the relation between the coherent and the incoherent part of the scattered power. The latter is a function of the correlation length of the surface waves. Because the correlation length changes with respect to the direction of the line of sight relative to the wave direction, the attenuation must show an anisotropic characteristic. In this work, we present a method to derive the wave direction from the anisotropy of the attenuation of the SNR data. The method is investigated based on simulated data as well by the analysis of experimental data from a GNSS station in the North Sea.

The paper investigates the theory of operation of a passive millimeter-wave seeker sensor using fast electronic sequential-lobing technique and the experimental validation obtained through laboratory trials. The paper analyzes in detail the theoretical performance of a difference channel sensor and a pseudo-monopulse sensor deriving agile formulas for the estimation of target angular tracking accuracy and the subsequent experimental validation.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

Recently, a paper was written to establish semi-structured complex numbers ℍ (a new number set invented to enable division by zero) as a useful mathematical tool providing novel results from its application in engineering and science. Whilst the paper was a milestone, the application of this number set to quantum and classical physics had not been fully explored. Consequently, the aim of this research was to use semi-structured complex numbers to develop a new mathematical model for the mass of an object and in course unite classical and quantum physics in a simple yet effective manner. As its major contributions this paper: (1) develops a new mathematical model for the mass of an object called the wave-mass function using De Broglie’s mass and frequency relation and semi-structured complex numbers; (2) uses the new wave-mass function to determine what happens to an object traveling at the speed of light; (3) derives a relation between Schrödinger’s wave function and the new wave-mass function; (4) derives a relation between Einstein’s Field Equation and the new wave-mass function; (5) uses the wave-mass function to combine Einstein’s Field Equation with Schrödinger’s wave function to form a new quantum gravity equation. These results and their applications provide a firm foundation to advance the number set ℍ as a useful mathematical tool.

Ocean surface waves have been utilized as fundamental information in various fields of oceanic research. In this paper, we suggest a simulation and modelling technique for generating an ocean surface wave using an inverse Fast Fourier Transform (iFFT), and we subsequently verify the wave’s accuracy. The conventional method, linear superposition, requires recursive calculation because of the double summation and the time variable; to circumvent this issue, the new algorithm is presented. The Joint North Sea Wave Project (JONSWAP) spectrum is utilized for the ocean surface wave simulation example, and the parameters are the significant wave height (HS) and the zero-crossing wave period (TZ). A coordinate transform for the wavenumber domain was used to apply the inverse FFT algorithm. To verify the accuracy of the simulation result, the relative error between the input condition and the analysis result was calculated. The result for TZ is below 4% relative error, and the maximum relative error for HS is 7%. To avoid the Nyquist frequency for wave-field analysis and simulation, the minimum grid size was calculated by twice applying the maximum wavenumber.

This work presents an application called APPMAR 1.0 based on Python ® environment, built to perform the downloading, treatment and analysis of meteorological and marine information. This application is composed of two main modules: the first module allows the downloading of information from the database (NOAA - WW3); the second module uses the principles of statistical mathematics for the treatment of waves and wind. The importance of this simple application is based on the free and agile access to meteorological and marine information for a coastal project. The determination of representative conditions of sea states ultimately will govern the process of design of coastal and oceanic infrastructure. The analysis of historical time series of local waves and winds allows the evaluation of average regimes or operational design, the ultimate limit states or extreme design, and the storms or design by persistence. In spite that the former analysis is a common task for coastal engineers, the codes generated are seldom shared for public use. In summary, for operational purposes is useful to have a freeware that can assist in the data processing for decision making and forcing of the mathematical models that are part of the common practice of coastal, oceanic and offshore engineering. This application has been tested in the Caribbean area of Colombia where meteorological and marine information are scarce.

We apply utilized the extended form of the auxiliary equation method to obtain extensively reliable exact travelling wave solutions of perturbed Gerdjikov–Ivanov equation (GIE) that is widely used as a model in the field theory of quanta and non-linear optics. The method is based on a simple first order second degree ODE. The new form of the approach gives more solutions to the governing equation efficiently.

In the present work a novel, portable and innovative eNose composed of a surface acoustic wave (SAW) sensor array based ZIF-8, and ZIF-67 nanocrystals (pure and combined with gold nanoparticles) as sensitive layers has been tested as a non-invasive system to detect and differentiate disease markers, such as acetone, ethanol and ammonia, related with early diagnosis of diabetes mellitus through exhaled breath. The sensors have been prepared by spin coating, achieving continuous and homogenous sensitive layers. Low concentrations (5 ppm, 10 ppm and 25ppm) of the marker analytes were measured, obtaining high sensitivities, good reproducibility, short time response and fast signal recovery.

Spinocerebellar ataxia type 3 is a neurodegenerative disease caused by an abnormal expansion of CAG repeats in the disease gene ATXN3, leading to prolonged polyglutamine (polyQ) tracts in the respective protein ataxin-3. The polyQ-expanded protein forms polyQ-containing aggregates in several brain regions which leads to neuronal cell loss. Autophagy is thought to play a significant role in clearing these polyQ-containing protein aggregates. Therefore, the autophagy mechanism was investigated in SCA3 with focus on the autophagic protein p62/sequestosome-1. Human and mouse RNA sequencing data were analyzed to determine RNA expression level of autophagic genes. Additionally, autophagy was studied in the SCA3 304Q knock-in mouse model and through several cell culture experiments using HEK-293T cells transfected with ATXN3 of differ-ent polyQ lengths. For cell culture experiments, autophagy was induced with rapamycin treat-ment, proteasomal degradation was blocked with MG132 and degradation of autophagic pro-teins was investigated using cycloheximide treatment. Here, we report an increased autophagy impairment with SCA3 disease progression seen in HEK-293T cells transfected with ATXN3 plasmid with expanded polyQ tracts, higher aged 304Q-knock-in mice, or human post-mortem brain material. Furthermore, co-localized aggregation of the autophagic protein p62 and the dis-ease protein ATXN3 was observed in the course of SCA3 disease. Therefore, we suggest a signifi-cant role for p62 in aggregate formation seen in the neurodegenerative disease SCA3.

To understand the biological relevance and mode of action of artificial protein ligands, crystal structures with their protein targets are essential. Here, we describe and investigate all known crystal structures that contain a so-called “molecular tweezer” or one of its derivatives with an attached natural ligand on the respective target protein. The aromatic ring system of these compounds is able to include lysine and arginine side chains, supported by one or two phosphate groups that are attached to the half-moon shaped molecule. We analyse the corresponding crystal structures with 14-3-3 proteins in complex with mono- and diphosphate tweezers. Furthermore, we solved crystal structures of two different tweezer variants in complex with the enzyme 1-Pyrroline-5-carboxyl-dehydrogenase (P5CDH), and found that the tweezers are bound to a lysine and methionine side chain, respectively. The different binding modes and their implications for affinity and specificity are discussed, as well as the general problems in crystallizing protein complexes with artificial ligands.

For Interferometry Synthetic Aperture Radar (InSAR), the normal baseline is one of the main factors that affect the accuracy of the ground elevation. For Gaofen-3 (GF-3) InSAR processing, the poor accuracy of the real-time orbit determination resulting in a large baseline error, leads to the modulation error in azimuth and the slope error in range for timely Digital Elevation Model (DEM) generation. In order to address this problem, a baseline estimation method based on external DEM is proposed in this paper. Firstly, according to the characteristic of the real-time orbit of GF-3 images, orbit fitting is executed to remove the non-linear error factor. Secondly, the height errors are obtained in slant-range plane between Shuttle Radar Topography Mission (SRTM) DEM and the GF-3 generated DEM after orbit fitting. At the same time, the height errors are used to estimate the baseline error which has a linear variation. In this way, the orbit error can be calibrated by the estimated baseline error. Finally, DEM generation is performed by using the modified baseline and orbit. This procedure is implemented iteratively to achieve a higher accuracy DEM. Based on the results of GF-3 interferometric SAR data for Hebei, the effectiveness of the proposed algorithm is verified and the accuracy of GF-3 real-time DEM products can be improved extensively.

We examine here characteristics of electromagnetic waves that propagate through an unbounded space filled with a homogeneous isotropic chiral medium. Resulting characters are compared to those of the electromagnetic waves propagating through an achiral free space. To this goal, we form energy conservation laws for key bilinear parameters in a chiral case. Due to a nonzero medium chirality, conservation laws turn out to contain extra terms that are linked to the spin-orbit coupling, which is absent for an achiral case. As an example, we take a plane wave for achiral case to evaluate those bilinear parameters. Resultantly, the conservation laws for a chiral case are found to reveal inconsistencies among several bilinear parameters that constitute the con-servation laws , thereby prompting us to establish partial remedies for formulating proper wave-propagation problems.

Boulder dynamics may provide essential data for the coastal evolution and hazards assessment and can be focused as a proxy for the onshore effect of intense storm waves. In this work, detailed observations of currently available satellite imagery of the Earth surface allowed to identify several coastal boulders displacements in the Southern Apulia coast (Italy), in a period between July 2018 and June 2020. Field surveys confirmed the displacements of several dozens of boulders up to several meters in size, also allowing the determination of the initial position for many of them. Archive weather analyses identified two possible causative storms during the same period, and calculations based on analytical equations are found in agreement with the displacement by storm waves for most of the observed boulders. The results help to give insights about the onshore effect of high storm waves on the coastal hydrodynamics and the possible future flooding hazard in the studied coast.

Maxwell equation for the electric field has been solved for any medium by suggesting the wavenumber and angular frequency be complex quantities. This accounts for the field decay by interaction with the medium.This expression for the time and special decay of the electric field in a medium is used to construct a new wave function sensitive to the medium physical properties. This new wave function, unlike the conventional one, differentiates between a beam of particles in a vacuum and that enters a medium which is an attenuated due to the scattering effect.Another expression for time decaying electric field was obtained using Newton’s laws for frictional medium. This expression shows that the electric field diminishes due to friction.Fortunately, this time decaying part of the electric field is typical to that derived from Maxwell’s equations. Finally, a new Schrodinger equation sensitive to the medium properties was derived. This equation, fortunately, describes some scattering processes for Protein scattering, scattering of x-rays, opto-acoustic phonons, and Raman scattering for some materials successfully .

The storm of November 12th-13th, 2019 provoked the displacements of boulders in a central Mediterranean rocky coast; with reference to a selected area, prone to the boulder production and geomorphologically monitored for years, a field-oriented study approach was applied for the phenomenon, by collating data concerning pre-storm locations and kinematics of these boulders. The number of displaced boulders is 11, that is, in terms of morphological imprint of a specific storm, one of the major study cases for the Mediterranean. In addition, based on widely used hydrodynamic equations, the minimum wave height required to displace the boulders is assessed. The values conform with the expected values for the wave climate dominating during the causative meteorological event and give a measure of the energy of the storm slamming the coast. Boulder dislodgements usually have plays a key role in determining the rate of the coastal recession, likely also in the investigated area. In view of an adverse climate evolution with a possible increase of energy and frequency of severe storms, the results deriving from the study of this morphodynamics should be considered for the hazard assessment and coastal management.

Breast cancer develops upon sequential acquisition of driver mutations in mammary epithelial cells; however how these mutations collaborate to transform normal cells remains unclear in most cases. We aimed to reconstitute this process in a particular case. To this end, we combined the activated form of the PI 3-kinase harboring the H1047R mutation with the inactivation of the histone lysine methyl-transferase KMT2D in the non-tumorigenic human mammary epithelial cell line MCF10A. We found that PI 3-kinase activation promoted cell cycle progression, especially when growth signals were limiting, as well as cell migration, both in a collective monolayer and as single cells. Furthermore, we showed that KMT2D inactivation had relatively little influence on these processes, except for single cell migration that KMT2D inactivation promoted in synergy with PI 3-kinase activation. Combination of these two genetic alterations induced expression of the ARPC5L gene that encodes a subunit of the Arp2/3 complex. ARPC5L depletion fully abolished the enhanced migration persistence exhibited by double-mutant cells. Our reconstitution approach in MCF10A has thus revealed both the cell function, single cell migration, and the underlying Arp2/3-dependent mechanism, which are synergistically regulated when KMT2D inactivation is combined with the activation of the PI 3-kinase.

Among cross-sectional imaging modalities, computed tomography (CT) is more available and faster; however, magnetic resonance (MR) performs better in terms of sensitivity and specificity, due to its higher contrast resolution. The appearance of peritoneal deposits on CT and MR depends mainly on the primary tumour histology: in case of unknown primary tumour (3-5% of cases), their behaviour at imaging may provide insights on the tumour origin. The time-point of tumour evolution, previous or ongoing treatments and the peritoneal spaces where they occur, also play an important role in determining the appearance of peritoneal deposits. Thus, knowledge of peritoneal anatomy and fluid circulation is mandatory in detection and characterization of peritoneal deposits. Several benign and malignant conditions may show similar imaging features that overlap those of PC, making the differential diagnosis challenging. Clinical history, laboratory findings and previous imaging examinations must be considered to achieve the correct diagnosis.

Cellulose nanocrystals (CNCs) are a kind of nano-inclusions that have experienced tremendous expansion in the material industry due to their outstanding mechanical qualities, sizable surface area, and capacity for functional tuning. Due to their vast potential, however, present practises fall short of fully using them. For example, employing CNCs in various matrices with various surface chemistries can be challenging; this problem tends to get worse if the focus is furthered on bio-based applications. This paper reviews the use of CNCs as fillers in natural and man-made polymers; we have explored in depth the production, characterisation, and of CNCs from various sources and their inclusion into various matrices. Surface alterations and the introduction of CNCs in biodegradable polymer can have a significant impact on several industrial behemoths such as tissue engineering and biomedical applications; therefore, pursue of current manuscript is extremely warranted. Throughout the manuscript various assembly techniques that involves alteration and adjustment of polymer network in building up a hydrogel with higher fracture energy and mechanical properties are also included. From rheological perspective the hydrogel processing is also discussed with some models routinely used in the literature to describe these hydrogels. Finally, bio-based hydrogels mechanically reinforced with CNCs such as Xanthan Gum, Alginate, protein, and polysaccharides were discussed.

Background: Monoclonal antibodies against PD-1 or PD-L1 are established in clinical practice for the treatment of both early and advanced/metastatic triple-negative breast cancer. Beyond the established immune checkpoints (ICPs) (PD-1 and CTLA-4) additional ICPs such as lymphocyte activation gene-3 (LAG-3) are subject of current research. In the present retrospective gene ex-pression analysis, we evaluated the prognostic significance of LAG-3 in 461 patients with early breast cancer. In addition, we examined whether there was a correlation between the different ICPs and CD8 expression. Methods: Using microarray-based gene expression analysis, we examined the prognostic signif-icance for metastasis-free survival (MFS) of LAG-3 mRNA expression in the whole cohort of 461 breast cancer patients and among different molecular subtypes. Correlations were analyzed us-ing Spearman-Rho correlation coefficient. Results: In the whole cohort, LAG-3 expression had no significant impact on MFS (p = 0.712, Log Rank). In the subgroup analyses, there was a trend, that higher LAG-3 expression was associated with favorable outcome in the luminal B (p = 0.217), basal-like (p = 0.370) and HER2 (p = 0.089) subtypes, although significance was not reached. In contrast, in multivariate Cox regression analysis adjusted for age, tumor size, axillary nodal status, histological grade of differentiation and the proliferation marker Ki-67, LAG-3 showed a significant influence on MFS (HR 0.574; 95% CI 0.369–0.894; p = 0.014). High LAG-3 significantly correlated with CD8 ( = 0.571; p < 0.001). Conclusion: LAG-3 expression had an independent impact on MFS. In addition to PD-1 and PD-L1, further immune checkpoints such as LAG-3 could serve as therapeutic targets in breast cancer.

Salivarian trypanosomes are extracellular parasites causing anthroponotic and zoonotic infections. Anti-parasite vaccination in considered the only sustainable method for global trypanosomosis control. Unfortunately, not a single field applicable vaccine solution has been successful so far. Active destruction of the host’s adaptive immune system by trypanosomes is believed to contribute to this problem. Here we show Trypanosome brucei brucei infection results in the lasting obliteration of immunological memory, including vaccine-induced memory against non-related pathogens. Using the well-established DTPa vaccine model in combination with a T. b. brucei infection and diminazene diaceturate anti-parasite treatment scheme, our result demonstrate that while the latter ensured the full recovery from the T. b. brucei infection, it failed to restore an efficacious anti-pertussis vaccine recall response. DTPa vaccine failure coincided with a shift in the IgG1/IgG2a anti-pertussis antibody ratio in favor of the latter, and a striking impact on all spleen immune cell populations. Interestingly, an increased plasma IFNy level in DTPa vaccinated trypanosome infected mice did result in a temporary antibody-independent improvement of early-stage trypanosomosis control. In conclusion, our results are the first to show that trypanosome inflicted immune damage is permanent, and is not restored by successful anti-parasite treatment.

NS-3 is one of the most used Network Simulators because it includes different modules, applications and protocols to simulate a wide range of network. Since new proposals usually involve a large number of simulations, a procedure to automatize the simulation process and extract statistics is very useful. "Statistical Framework" (SF) is an important module of NS-3 because it fulfills this need. SF allows us to collect simulation data and obtain statistical reports for NS-3. In this report, we present a detailed description of statistical framework module and two useful examples of its configuration.

Network Simulators is typically used to study services and applications in complex scenarios due to the infeasibility of deploying real testbeds. Many problems can be solved by using network simulators such as NS-3. With this in mind, the aim of this article is to introduce new NS-3 users through detailed information. It is sometimes difficult to handle by new users the traditional manuals developed by NS-3 project official website. In this article, NS-3 for communication network and Eclipse Integrated Development Environment (IDE) for powerful programming language are integrated step-by-step, explaining the main features of these open source software packages and concluding with an example simulation. Our effort is to make it easy for a beginner to be part of the NS-3 research community and to maintain an open environment of knowledge.

The co-occurrence of depression and obesity has become a significant public health concern worldwide. Recent studies have shown that metabolic dysfunction, which is commonly observed in obese individuals and characterized by inflammation, insulin resistance, leptin resistance, and hypertension, is a critical risk factor for depression. This dysfunction may induce structural and functional changes in the brain, ultimately contributing to depression's development. Given that obesity and depression mutually increase each other's risk of development by 50-60%, there is a need for effective interventions that address both conditions. The comorbidity of depression with obesity and metabolic dysregulation is thought to be related to chronic low-grade inflammation, characterized by increased circulating levels of pro-inflammatory cytokines, and C-reactive protein (CRP). As pharmacotherapy fails in at least 30-40% of cases to adequately treat major depressive disorder, a nutritional approach is emerging as a promising alternative. Omega-3 polyunsaturated fatty acids (n-3 PUFAs) are a promising dietary intervention that can reduce inflammatory biomarkers, particularly in patients with high levels of inflammation, including pregnant women with gestational diabetes, patients with type 2 diabetes mellitus, and overweight individuals with major depressive disorder. Further effort directed to implement these strategies in clinical practice could contribute to improved outcomes in patients with depression and comorbid obesity and/or metabolic dysregulation.

Rationale: The 14-3-3 protein family is known to interact with many proteins in non-cardiac cell types to regulate multiple signaling pathways, particularly those relating to energy and protein homeostasis; and the 14-3-3 network is a therapeutic target of critical metabolic and proteostatic signaling in cancer and neurological diseases. Although the heart is critically sensitive to nutrient and energy alterations, and multiple signaling pathways coordinate to maintain the cardiac cell homeostasis, neither the structure of cardiac 14-3-3 protein interactome, nor potential functional roles of 14-3-3 protein-protein interactions (PPIs) in heart has been explored. Objective: To establish the comprehensive landscape and characterize the functional role of cardiac 14-3-3 PPIs. Methods and Results: We evaluated both RNA expression and protein abundance of 14-3-3 isoforms in mouse heart, followed by co-immunoprecipitation of 14-3-3 proteins and mass spectrometry in left ventricle. We identified 52 proteins comprising the cardiac 14-3-3 interactome. Multiple bioinformatic analyses indicated that more than half of the proteins bound to 14-3-3 are related to mitochondria; and the deduced functions of the mitochondrial 14-3-3 network are to regulate cardiac ATP production via interactions with mitochondrial inner membrane proteins, especially those in mitochondrial complex I. Binding to ribosomal proteins, 14-3-3 proteins likely coordinate protein synthesis and protein quality control. Localizations of 14-3-3 proteins to mitochondria and ribosome were validated via immunofluorescence assays. The deduced function of cardiac 14-3-3 PPIs is to regulate cardiac metabolic homeostasis and proteostasis. Conclusions: Thus, the cardiac 14-3-3 interactome may be a potential therapeutic target in cardiovascular metabolic and proteostatic disease states, as it already is in cancer therapy.

This study presents a novel method based in ray tracing for analyzing wave propagation in composites, specifically tailored for Structural Health Monitoring applications. The method offers distinct advantages over the commonly used Finite Element Method mainly in computational resource utilization, that has become a limiting factor for this kind of analyses. The ray tracing method is evaluated against a number of example cases representing structural details such as thickness changes, stringers or simulated damages and it highlights the significance of ray tracing to study wave propagation under these conditions and how it can serve as a valuable tool for structural health monitoring.

Current-voltage characteristics curves of NFinFET are presented and are fitted with the modi-fied current-voltage (I-V) formulas, where the modified term in the triode region is demon-strated to be indispensable. In the as-known I-V formula, important parameters need determin-ing to make both the measured data and the fitting data as close as possible. Those parameters include kN (associated with the sizes of the transistor and mobility), (associated with Early Voltage), and Vth (the threshold voltage). The differences between the measured data and the fit-ting data vary as the applied source-drain bias, proving that the mobility of the carriers is not consistently constant. On the other hand, a modified formula, called kink effect factor, is nega-tively or positively added simulating solitary heat waves, which disturb the propagation of car-riers and thus influence the Source-Drain current (IDS). The new statistical standard deviations () are then found to be effectively suppressed as the kink effect is taken into account.

Arterial ageing is thought to cause a diastolic-to-systolic shift in the return time (RT) of backward waves to central arteries. However, current methods of estimating RT—inflection point, zero crossing, and foot methods—depend on a single waveform feature and produce systolic RT throughout life. We propose a novel centroid method that accounts for the entire backward pressure waveform and develop a ground truth RT (GTRT), which can be used in computational models to test the accuracy of RT estimation methods. Linear wave tracking was implemented in a one-dimensional systemic arterial tree model and GTRT was calculated as the amplitude-weighted mean RT of backward waves at the ascending aorta. Using a virtual cohort of 1200 patients, the centroid RT was closest to GTRT compared to the zero crossing, inflection point, and foot methods; mean differences (limits of agreement) were -8 (-47,30), vs -42 (-136,52), -78 (-305,149), and -197 (-379,-15) ms, respectively. The sensitivity of the methods to changes in RT was also assessed in ten sheep. A balloon catheter in the descending thoracic aorta was used to generate a backward-running pulse that arrived at the ascending aorta at different times during diastole or systole, allowing the “bulk” RT of the backward-running wave ensemble to be manipulated. Only the centroid method was sensitive to both diastolic and systolic changes in RT. We conclude that the accuracy and robustness of the centroid method make it most suitable for evaluating the diastolic-to-systolic shift in RT of backward waves with ageing.

The arterial network in healthy young adults is thought to be structured to minimise wave reflection in conduit arteries, producing an ascending aortic pressure waveform with three key features: early systolic peak, negative systolic augmentation, and diastolic hump. One-dimensional computer models have provided significant insights into arterial haemodynamics, but no previous models of the young adult have exhibited these three features. Since the latter was likely to be related to unrepresentative or non-optimised impedance properties of the model arterial networks, we developed a new ‘YoungAdult’ model that incorporated 1) a novel and more accurate empirical equation for approximating wave speeds, based on area and relative distance to elastic-muscular arterial transition points, 2) optimally-matched arterial junctions, and 3) an improved arterial network geometry that eliminated ‘within-segment’ taper (which causes wave reflection in conduit arteries) whilst establishing ‘impedance-preserving’ taper. These model properties led to wave reflection occurring predominantly at distal vascular beds, rather than in conduit arteries. The model predicted all three typical characteristics of an ascending aortic pressure waveform observed in young adults. When compared with non-invasively acquired pressure and velocity measurements (obtained via tonometry and Doppler ultrasound in 7 young adults), the model was also shown to reproduce the typical waveform morphology observed in the radial, brachial, carotid, temporal, femoral, and tibial arteries. The YoungAdult model provides support for the concept that the arterial tree impedance in healthy young adults is exquisitely optimised, and it provides an important baseline model for investigating cardiovascular changes in ageing and disease states.

In this paper, we revisit the hydrodynamics supporting the design and development of the RiverCat class of catamaran ferries operating in Sydney Harbor since 1991. More advanced software is used here. This software accounts for the hydrodynamics of the transom demisterns which experience partial or full ventilation, depending on the vessel speed. This ventilation gives rise to the hydrostatic drag, which adds to the total drag of the vessel. The presence of the transom also creates a hollow in the water. This hollow causes an effective hydrodynamic lengthening of the vessel, which leads to a reduction in the wave resistance. Hence a detailed analysis is required in order to optimize the size of the transom. It is demonstrated that the drag of the vessel and the wave generation can be predicted with good accuracy. Finally, the software is also used to optimize the vessel further by means of affine transformations of the hull geometry.

The most important conclusion from this article is that from the General Theory of Relativity (GTR) do not result any gravitational waves, but just ordinary modulation of the gravitational field intensities caused by rotating of bodies. If the LIGO team has measured anything, it is only this modulation, rather than the gravitational wave understood as the carrier of gravity. This discussion shows that using too complicated mathematics in physics leads to erroneous interpretation of results (in this case, perhaps the tensor analysis is guilty). Formally, various things can be calculated, but without knowing what such analysis means, they can be attributed misinterpreted. Since the modulation of gravitational field intensities has been called a gravitational wave in contemporary physics, we have also done so, although it is misleading. In the article it was shown, that from the Newton’s law of gravitation resulted an existence of gravitational waves very similar to these, which result from the General Theory of Relativity. The article shows differences between the course of gravitational waves that result from Newton’s gravitation, and the course of gravitational waves that result from the General Theory of Relativity, which measurement was announced by the LIGO (Laser Interferometer Gravitational-Wave Observatory) [1], [2], and [5]. According to both theories, gravitational waves are cyclical changes of the gravitational field intensities. The article proposes a method of testing a laser interferometer for gravitational wave measurement used in the LIGO Observatory. Criticism of results published by the LIGO team was also presented.

Nonlinear ultrasonic testing has been accepted as a promising manner for evaluating material integrity in an early stage. Stress fatigue is the main threats to train safety, railways examinations for stress fatigue are more significant and necessary. A series of ultrasonic nonlinear wave experiments are conducted for rail specimens extracted from railhead with different degree of fatigue produced by three-point bent loading condition. The nonlinear parameter is the indicator of nonlinear waves for expressing the degree the fatigue. The experimental results show that the sensitivity of a third harmonic longitudinal wave is higher than second harmonic longitudinal wave testing. As the same time, collinear wave mixing shows strong relative with fatigue damages than a second longitudinal wave NDT method and provides more reliable results than third harmonic longitudinal waves nonlinear testing method.

In the Majorana equation for particles with arbitrary spin, the wave packet is due not only to the uncertainty affecting position and momentum but also to the infinite components with decreasing mass forming the Majorana spinor. In this paper we prove that such components contribute to increase the spreading of the wave packet. Moreover, as occurs in the time propagation of the Dirac wave packet, also in that of Majorana the Zitterbewegung takes place, but it shows a peculiar fine structure. Finally, the group velocity always remains subluminal and the contributions due to the infinite components decrease progressively increasing the spin.

The smart management of water resources is an increasingly important topic in today's society. In this context, the paradigm of Smart Water Grids (SWGs) aims at a constant monitoring through a network of smart nodes deployed over the water distribution infrastructure. In such a way, a continuous assessment of water quality and state of health of the pipeline infrastructure can be achieved, allowing an early detection of leaks and water contamination. Acoustic wave-based technology has arisen as a viable communication technique among the nodes of the network. Such technology can be suitable to replace traditional wireless networks in SWGs, as the acoustic channel is intrinsically embedded in the water supply network. However, the fluid-filled pipe is one of the most challenging media to be employed for data communication. This paper aims at reviewing those works dealing with acoustic-based communication networks in real large-scale urban water supply networks. An overview on the characteristics, trends and design challenges of existing works is provided as a guideline for future research.

The operational measure (OM) of the Second-Generation Intact Stability Criteria (SGISC) is the initial step toward the design of a performance-based dynamic stability assessment of the ship by considering both the vessel’s operation, loading condition and weather parameters. The SGISC recommends the standard wave scatter table (WST) for the environmental data, an indefinite requirement for a simplified assessment pathway, which provides the probability of wave occurrence. The existing standard WST was developed based on the North Atlantic Ocean. This study aims to identify the discrepancy in the probability of wave occurrence in the IMO-recommended WST when compared with developed hindcast WST for smaller regions of the North Atlantic Ocean for the application of SGISC. The significant difference in the existing standard WST is identified when compared with hindcast data, especially across different seasons. A case study of OM on the C11 class post-Panamax container ship for excessive acceleration is provided to better represent the study. The identified limitation limits the use of standard WST in ship stability assessment. The study recommends using hindcast-based WST for SGISC applications that are region and season based. This recommendation is beneficial in improving the safety assessment by OM, given the data is reliable and available for the season and region-specific, and hence the accuracy of the ship stability can be improved while using for the SGISC OM assessment. Further, it makes the WST adhere to the actual framework of the SGISC, i.e., using existing environmental data for design assessment and improving the simplified stability analysis.

The coastline in the Ca Mau and the Kien Giang provinces of the Vietnamese Mekong Delta has been severely eroded in recent decades. Pile-Rock Breakwaters (PRBW) are one of the most widely adopted structures for controlling shoreline erosion in this region. These structures are effective for wave energy dissipation, stimulating sediment accumulation, and facilitating the restoration of mangrove forests. These breakwaters are generally considered to be best-engineering practice however there is currently insufficient scientific evidence with regard to specific structural design aspects. This can lead to PRBW structures being compromised when deployed in the field. This study uses a physical model of a PRBW in a laboratory to investigate several design parameters, including crest width and working states (i.e. submerged, transition, and emerged), and investigates their relationship with the wave transmission coefficient, wave reflection coefficient, and wave energy dissipation. To investigate these relationships further, empirical formulas were derived for PRBWs under different sea states and crest widths to aid the design process. The results showed that PRBW width had a significant influence on the wave energy coefficients. The findings revealed that the crest width of the breakwater is inversely proportional to the wave transmission coefficient (K_t) under the emerged state. The crest width is also proportional to the wave reduction efficiency and wave energy dissipation in both working states (i.e., submerged and emerged states). The front wave disturbance coefficient (K_f) was found to be proportional to the wave reflection coefficient, and the wave height in front of the structure was found to increase by up to 1.4 times in the emerged state. The wave reflection coefficient requires special consideration to reduce the toe erosion in the structure. Lastly, empirical equations including linear and non-linear formulas were compared with previous studies for different classes of breakwaters. These empirical equations will be useful for understanding the wave transmission efficiency of PRBWs. The findings of this study provide important guidance for PRBW design in the coastal area of the Mekong Delta.

Maxwell’s equations are valid only for a stationary observation point, therefore, to adequately describe real processes so far we have had to move to a moving reference frame. This paper presents the equations of electrodynamics for the moving observation point, it is shown that plane and spherical electromagnetic waves are their solutions, while the spherical wave propagates only outward, which cannot be said about Maxwell’s equations. The fields of uniformly moving charges are also solutions of the equations. Now there is no need to move to a moving reference frame, to use four-dimensional space and covariant form of equations. The question of finding a universal form of the equations that allows a solution in the form of the field of an arbitrarily moving charge remains open. This raises the question of the existence of a two-parameter group of transformations of electromagnetic fields along with the known one-parameter group has been posed. The phenomena derived from the equations, which make an additional contribution to the phase overrun in the Aharonov-Bohm effect are considered. The equation of motion of a charged particle in an electromagnetic field without simplifying approximations is considered, which allows us to take into account the radiation effects. It is shown that the fields in a moving observation point depend on its velocity and acceleration. In particular, although in a constant uniform electric field a force qE acts on a motionless charged particle, but on the same motionless but not fixed particle the force 4/3qE acts already, because it has a nonzero acceleration and the electric field at this point is larger. As the speed increases, the field decreases, and when it reaches the speed of light, when the particle stops accelerating, the force again becomes equal to qE The principle of operation of an unconventional alternator in a constant electric field and its corresponding engine, as well as new types of direct and impulse current generators, predicted by the equations, are described.

The ordinary 3D wave equation for nondissipative, homogeneous, isotropic media admits solutions where the point sources are permitted to move, but it does not admit solutions where the receiver is allowed to move. To overcome this limitation, the new wave equation is derived, permitting both the receiver and the source to move. This new wave equation is a generalization of the standard wave equation, and it reduces to the standard wave equation when the receiver is at rest. To derive this new wave equation, we first mathematically define a diverging spherical wave caused by the stationary point source. From this purely mathematical definition, the wave equation for the stationary source and the moving receiver is derived together with the corresponding free-space Green's function. Utilizing the derived Green's function, it was shown that this new wave equation also permits the solutions where both the receiver and the source are permitted to move. In conclusion, this paper demonstrates that, instead of an ordinary wave equation, the wave equation for the moving source and the moving receiver governs the waves emitted by the moving point sources and received by the moving receivers.

The article is devoted to the analytical and numerical study of the pattern of propagation and attenuation, due to Coulomb friction, of shear waves in an infinite thin elastic plate with a circular orifice of radius lying on a rough base. In the field of motion, an exact analytical solution of a nonlinear boundary value problem for tangential stresses and transversal velocities is obtained in quadratures by the method of Laplace transformations. It turned out that the complete exhaustion of the wave front of a strong rupture occurs at a finite distance from the center of the hole and an elementary formula is given for this distance (the case of tangential forces instantly applied to the orifice boundary, and then constant in time, is considered). For various ratios of the magnitude of the limiting friction force to the amplitude of the applied load, the trailing wave fronts are obtained, after which a state of static equilibrium between the elastic and friction forces with a nonlinear distribution of residual deformations is established in the region .

In 2011, by 1.3 mm wavelength VLBI radio wave observations of the SgrA*, Fish, V. L. et al showed that the emissions tightly related to the formation of a black hole shadow have a remarkably large time-varying feature within a region of less than 50 μas. The present paper suggests that the origin of the time variation in the observed emission is due to effects of the orbital motion of the existing super-massive black hole binary orbiting at SgrA* with a period of 2150±2.5 s. This suggestion is based on observations of decameter radio wave pulses from SgrA*. We show a good correlation between the time variation in the coherent flux density of the VLBI results and the time variation model of estimated emission intensities based on the periodic motion of the super-massive black hole binary by applying parameters deduced from the decameter radio wave pulse observation model (DRWP-Model). With further confirmation by Fourier analyses of the potential periodicity of the VLBI data that show the same periods of DRWP Model, we conclude that the time variation detected by the 1.3 mm wavelength radio wave VLBI is evidence of an existing super-massive black hole at Sgr A*.

A simplified nonlinear dispersive system of BBM-type, initially derived by D. Mitsotakis, is employed here in order to model the generation and propagation of surface water waves over variable bottom. The simplification consists in applying the so-called Boussinesq approximation. Using the finite element method and the FreeFem++ software, we solve numerically this system for three different complexities for the bathymetry function: a flat bottom case, a variable bottom in space, and a variable bottom both in space and in time. The last case is illustrated with the Java 2006 tsunami event. This article is designed rather as a tutorial paper even if it contains the description of completely new adaptation techniques.

Although multiple sclerosis (MS) is an inflammatory demyelinating disease of the central nervous system (CNS) that results in many neurological disabilities, optic neuritis (ON) is developed in some MS patients. However, the molecular mechanism of ON remains unknown. Galectins, β-galactoside-binding lectins, are involved in various pathophysiology. We have previously shown that galectin-3 (gal-3) is associated with the pathogenesis of experimental autoimmune encephalomyelitis (EAE), its animal model for human MS. In the current study, the expression of gal-3 was explored in the visual pathway of the EAE mice to clarify the pathogenesis of ON. Immunohistochemical analysis demonstrated that expression of gal-3 was increased in the visual pathway of the EAE mice during the peak disease, compared with naïve and EAE mice during the chronic disease. Expression of gal-3 was observed in mainly microglia/macrophages and astrocytes in the visual pathway of the EAE mice. In addition, gal-3+Iba-1+ cells with the phagocytic activities reflected by immunostaining with cathepsin-D were accumulated at demyelinating lesions in the visual pathway during peak disease of EAE. Moreover, NLRP3 expression was also detected in most gal-3+Iba-1+ cells. These results indicate a considerable possibility that gal-3 regulates the NLRP3 signaling in microglia/macrophages, followed by neuroinflammatory demyelination in ON. By contrast, astrocytic expression of gal-3 was also observed from the peak to the chronic disease. Taken together, the current study suggests a critical role of gal-3 in the pathogenesis of ON and proposes gal-3 in glial cells as a potential therapeutic target for ON.

The patient was a 44-year-old woman with suspected Stevens-Johnson syndrome due to Baktar® (sulfamethoxazole trimethoprim) medication received at our outpatient dermatology clinic. Histopathological examination of the epidermis, dermis, and subcutaneous adipose tissue samples showed numerous necrotic keratinocytes in the epidermis. Apoptotic nuclei were visualized as diaminobenzidine brown deposits with immunoperoxidase staining for cleaved caspase-3. Cleaved-caspase3-positive findings were consistent with eosinophilic material that appeared to be necrotic cells within the epidermis. Therefore, these eosinophilic materials must be apoptotic bodies. Generally speaking, and especially in Japan, these materials are considered necrotic keratinocytes. To our best knowledge, no studies have used apoptotic immunohistochemical markers to examine whether these structures are apoptotic.

Crohn's disease is a non-specific inflammatory bowel disease, which is a chronic condition that affects the ileum and/or large intestine. At the same time, it can also involve any other part of the human body, that is, from the mouth to the anus. The symptoms are very bothersome and cause a significant reduction in quality of life and sometimes even crippling permanent damage to the gastrointestinal tract, which requires enteral or parenteral nutrition for life. The purpose of this study was to investigate tissue metalloproteinases as markers of recurrent Crohn's disease. The experimental groups included 31 patients and 10 patients with normal Crohn's disease, ranging in age from 23-70 years, with a mean age of 40.4. Collected tissues were frozen and then fragmented tissues were homogenized with Ripa Lysis buffer on ice. The supernatant was collared and four metalloproteinases - MMP 3, MMP 7, MMP 8 and MMP 9 - were an-alized by Enzyme-linked Immunosorbent Assay using SEA101HU, SEA102Hu, SEA103Hu and SEA553Hu kits (Cloud-Clone Corp., Kata, TX, USA). All chemical analyses were performed in triplicate. Metalloproteinase content was expressed as mean ± standard deviation. Metalloproteinase 3 and metalloproteinase 8) significantly influenced the possibility of Crohn recurrence

The antibodies targeting invasive proteins of Plasmodium falciparum (Pf) merozoites is a clever strategy against malaria parasite. The recent finding that Plasmodium merozoites surface enolase is a target for growth neutralizing antibodies has generated interest in identifying its re-ceptor (s) on erythrocytes. In the present study, several biochemical experiments were undertaken involving recombinant Pf enolase and antibody against it to search for its cognate receptor. The binding of rPfeno to erythrocytes was selectively sensitive to trypsin but resistant to neuramini-dase. Failure of yeast enolase binding to human red blood cells under similar conditions indicat-ed high specificity of parasite Pfeno. The mass spectrometric and immunological analyses of pro-teins obtained in pull downs and co-immunoprecipitation samples led to identification of band 3 as an interactor/receptor for Plasmodium enolase. Structural characterization of sequences of band 3 - rPfeno interacting regions revealed C-terminal exocytic regions of band 3 to be binding to Pfeno. Similarly, band 3 binding regions of rPfeno were also identified. Identification of receptor-ligand (band 3: Pfeno) pair paves the way for antimalarial anti-Pf enolase-based vaccine, anti-Pf enolase antibodies as drug and also for developing novel small molecule-based invasion inhibi-tory therapeutics including peptidomimetics that could disrupt the band 3: Pfeno protein-protein interactions.

Abstract: Oxidative metabolism is crucial for leukemic stem cell (LSC) function and drug resistance in acute myeloid leukemia (AML). Mitochondrial metabolism also affects the immune system and therefore the antitumor response. Modulation of oxidative phosphorylation (OxPHOS) has emerged as a promising approach to improve therapy outcome for AML patients. However, the effect of mitochondrial inhibitors on the immune compartment in the context of AML is yet to be explored. Immune checkpoints such as the ecto-nucleotidase CD39 and programmed dead ligand 1 (PD-L1) have been reported to be expressed in AML and linked to chemoresistance and poor prognosis. In the present study, we first demonstrated that a novel selective electron transfer chain complex (ETC) I inhibitor, EVT-701, decreased OxPHOS metabolism of murine and human cytarabine (AraC)-resistant leukemic cell lines. Furthermore, we showed that, while AraC induced immune response regulation by increasing CD39 expression and by reinforcing interferon-γ/PD-L1 axis, EVT-701 reduced CD39 and PD-L1 expression in vitro in a panel of both murine and human AML cell lines, especially upon AraC treatment. Altogether, this work uncovers a non-canonical function of ETCI in controlling CD39 and PD-L1 immune checkpoints, thereby improving the anti-tumor response in AML.

Let $\mathcal{N}$ be an arbitrary class of matroids, closed under isomorphism. For $k$ a positive integer, we say that $M \in \mathcal{N}$ is \emph{$k$-minor-irreducible} if $M$ has no minor $N \in \mathcal{N}$ such that $1\leq\left|E\left(M\right)\right|-\left|E\left(N\right)\right|\leq k $. Tutte's Wheels and Whirls Theorem establish that, up to isomorphism, there are only two families of 1-minor-irreducible matroids in the class of 3-connected matroids. More recently, Lemos classified the 3-minor-irreducibles with at least 14 elements in the class of triangle-free 3-connected matroids. Here we prove a local characterization for the 2-minor-irreducible matroids with at least 11 elements in the class of triangle-free 3-connected matroids. This local characterization is used to establish two new families of 2-minor-irreducible matroids in this class.

Thanks to the pioneering studies of Østerud and co-workers it is now increasingly understood that natural polyphenols present in marine oils play an essential role in protecting omega-3 lipids from oxidation and autooxidation ensuring that no proinflammatory products are formed after intake as it often happens with assumption of refined omega-3 concentrates. Strong antioxidants exerting multiple biological functions, olive biophenols are ideally suited to functionalize marine oils creating a synergy which has the potential to foster public health across the world. This study identifies suitable avenues to advance the sustainable production of health-beneficial formulations based on newly obtained natural marine oils and olive phenolic extracts. Important educational outcomes for bioeconomy educators conclude the study.