Droplet epitaxy allows the efficient fabrication of a plethora of 3D, III-V-based nanostructures on different crystalline orientations. Quantum dots grown on (311)A-oriented surface are obtained with record surface density, with or without a wetting layer. These are appealing features for quantum-dot lasing, thanks to the large density of quantum emitters and a truly 3D lateral confinement. However, the intimate photophysics of this class of nanostructures has not yet been investigated. Here we address the main optical and electronic properties of s-shell excitons in individual quantum dots grown on (311)A substrates with photoluminescence spectroscopy experiments. We show the presence of neutral exciton and biexciton as well as positive and negative charged excitons. We investigate the origins of spectral broadening, identifying them in spectral diffusion at low temperature and phonon-interaction at higher temperature, the presence of fine interactions between electron and hole spin, and a relevant heavy-hole/light-hole mixing. We interpret the level filling with a simple Poissonian model reproducing the power excitation dependence of the s-shell excitons. These results are relevant for the further improvement of this class of quantum emitters and their exploitation as single photon sources for low density samples as well as for efficient lasers for high density samples.

A power conservative Thevenin-Norton and Norton-Thevenin transformations are proposed in this letter. The transformations introduce a voltage and a current generators for which parameters depend on the loading impedance value.

in this article, an ultra-wideband traveling wave antenna with antipodal topology is proposed. The proposed design is realized on an economical substrate with minimum thickness. The proposed design offers an ultra-wide bandwidth of 26 to 40 GHz, translating to 42%. The dimensions of the antenna are 20mm x10mm x 0.5mm indicating an electrically compact structure. The proposed antenna offers high front to back ratio of at least 10dB across the bandwidth of operation. The forward gain of the antenna varies from 4 to 7dBi in the afore-mentioned band. The pattern integrity is maintained throughout the band. The antenna is fabricated using the commercial photolithography process. A mutli-step topology of the antennas is also proposed for wide angular coverage. The coverage is greater than 150º with mutual coupling less than 25dB. These performance metrics is achieved with a very small footprint. Simulated and experimental results are presented in this paper.

Sulfite and kraft pulping are two principal methods of industrial delignification of wood. In recent decades, those have been considered as possibilities to pretreat recalcitrant wood lignocellulosics for enzymatic hydrolysis of polysaccharides and subsequent fermentation of obtained sugars to valuable bioproducts. Current work compares chemistry and technological features of two different cooking processes in the preparation of polysaccharide substrates for deep sacchari-fication with P. verruculosum glycosyl hydrolases. Bleached kraft and sulfite pulps were subjected to hydrolysis with enzyme mixture of high xylanase, cellobiohydrolase and β-glucosidase activities at a dosage of 10 FPU/g of dry pulp and fiber concentration of 2.5, 5 and 10%. HPLC was used to analyze soluble sugars after hydrolysis and additional acid inversion of oligomers to monosaccharides. Kraft pulp demonstrated higher pulp conversion after 48 h (74-99%), mostly resulted from deep xylan hydrolysis. Sulfite-pulp hydrolysates, obtained in similar conditions, due to higher hexose concentration (more than 50 g/L), had higher fermentability for industrial strains producing alcohols, microbial protein or organic acids. Along with saccharification, enzymatic modification of non-hydrolysed residues occurred, which led to decreased degree of polymerization and composition changes in two industrial pulps. As a result, crystallinity of kraft pulp increased by 1.3%, which opens possibilities for obtaining new types of cellulosic products in pulp and paper industry. The high adaptability and controllability of enzymatic and fermentation processes creates prospects for the modernization of existing factories.

Over the past decade, there has been a remarkable acceleration in the evolution of smart cities and intelligent spaces, driven by breakthroughs in technologies such as the Internet of Things (IoT), edge-fog-cloud computing, and machine learning (ML)/Artificial Intelligence (AI). As society begins to harness the full potential of these smart environments, the horizon brightens with the promise of an immersive, interconnected 3D world. The forthcoming paradigm shift in how we live, work, and interact owes much to groundbreaking innovations in augmented reality (AR), virtual reality (VR), extended reality (XR), Blockchain, and Digital Twins (DT). However, realizing the expansive digital vista in our daily lives is challenging. Current limitations include an incomplete integration of pivotal techniques, daunting bandwidth requirements, and the critical need for near-instantaneous data transmission, all impeding the digital VR Metaverse from fully manifesting as envisioned by its proponents. This paper seeks to delve deeply into the intricacies of the immersive, interconnected 3D realm, particularly in applications demanding high levels of intelligence. Specifically, this paper introduces Microverse, a task-oriented, edge-scale, pragmatic solution for smart cities. Unlike an all-encompassing Metaverses, each Microverse instance serves a specific task as a manageable digital twin of an individual network slice. Each Microverse enables on-site/near-site data processing, information fusion, and real-time decision-making within the edge-fog-cloud computing framework. The Microverse concept is verified using smart public safety surveillance (SPSS) for smart communities as a case study, demonstrating its feasibility in practical smart city applications. The aim is to stimulate discussions and inspire fresh ideas in our community, guiding us as we navigate the evolving digital landscape of smart cities to embrace the potential of the Metaverse.

In this work, nanocomposite photoelectrodes of the TiO2/ Au composition were manufactured, in which the size of plasmonic Au nanoparticles was varied, and the morphology of the TiO2 layer, depending on the thickness, changed from an island to a continuous layer. The influence of the morphology of plasmonic Au nanoparticles and the TiO2 layer on the optical and photoelectrochemical characteristics of hybrid photoelectrodes was studied. It has been shown that continuous coating of Au nanoparticles with a TiO2 layer (layer thickness 10 and 15 nm) leads to a decrease in the photoelectric response, and the decrease in photocurrent density and photoconversion efficiency decreases in proportion to the thickness of the TiO2 layer. The indicated drop in characteristics when plasmonic particles are located under the TiO2 layer is presumably associated with the scattering and recombination of charge carriers in the semiconductor layer. The best performance was shown by a system in which large Au nanoparticles (10 nm) are coated with a 5 nm thick layer of titanium dioxide; in this geometry, Au nanoparticles are decorated with TiO2 nanoparticles, as a result of which the photoelectrode-electrolyte interface has a more complex structure.

The western Sulige gas field is a new and key reserve area for the rolling development of the Sulige gas field in China. However, due to the complex gas–water relationship and the difficulty in identifying gas and water formation, the scale and benefit deployment of the gas field are seriously restricted. In particular, almost all of the wells in the area produce water and no water measurement has been carried out for any single well, which leads to an unclear understanding of the dynamic characteristics of the production wells, thus affecting the productivity calculations of the gas wells and the overall regional productivity evaluation. Based on the testing data for a gas well, the impacts of the reservoir property parameters on the gas and water production were analyzed by combining the production performance and static geological characteristics. It was determined that the physical parameters K, Kh, and φSg had good positive correlations with gas production but not with water production; thus, effective prediction cannot be obtained for water production in gas well testing. After the analysis of the liquid loading law, the gas wells were classified into three types: continuous liquid carrying production, slight liquid loading, and liquid loading wells. In general, up to 96% of the gas wells were liquid loaded. According to the different production performances exhibited in the different stages of the gas wells, five types of methods for diagnosing water production wells were proposed (gas testing, pilot production, gas–liquid two-phase measurement testing, liquid level detection, and production performance analysis), as well as the diagnostic criteria and corresponding solutions. To obtain real-time water production data for each well and investigate the change of water-gas ratio (WGR) during the whole production process, a water production splitting method for gas wells based on three-dimensional geological modeling and numerical simulation combined with the constraints of the total water production of gas gathering stations was explored and established. The splitting results can be used to evaluate the water and gas productivity of gas wells and determine the best deliquification period. The gas well productivity when water production was considered was about 10% lower than that when water production was not considered. The best deliquification period was determined to be 125 days for wells with small water production, 20 days for wells with moderate water production, and 3 days for wells with serious water production. The results of this study could provide technical support for the scientific evaluation of gas well production indicators, reduction of development costs, and improvement of oil recovery.

The microorganisms able of accumulating lipids in high percentages, known as oleaginous microorganisms, have been widely studied as an alternative for producing oleochemicals and biofuels. Microbial lipid, so called Single Cell Oil (SCO), production depends on several growth parameters, including the nature of the carbon substrate, which must be efficiently taken up and converted into storage lipid. Οn the other hand, substrates considered for large scale applications must be abundant and of low acquisition cost. Among others, lignocellulosic biomass is a promising renewable substrate containing high percentages of assimilable sugars (hexoses and pentoses). However, it is also highly recalcitrant and therefore it requires specific pretreatments in order to release its assimilable components. The main drawback of lignocellulose pretreatment is the generation of several by-products that can inhibit the microbial metabolism. In this review, we discuss the main aspects related to the cultivation of oleaginous microorganisms using lignocellulosic biomass as substrate, hoping to contribute to the development of a sustainable process for SCO production in the near future.

Boost-derived converters are most popular in Power Factor Correction AC-DC conversion applications and alternative energy generation systems. The proper operation of such converters relies on housekeeping power supplies providing auxiliary power for their control circuitry. The purpose of this study is to present a design-oriented analysis of a simple, passive, isolated, self-bias circuit that can provide a stabilized voltage for the control circuits of boost-derived converters. The circuit’s output voltage inherently follows the main regulated output and therefore, does not require an additional active control. The paper presents a detailed analysis of the circuit and offers design guidelines. Following the presentation of the basic idea several variations of the circuit, that can be used in special applications, are presented. The feasibility of the proposed bias circuits was verified by simulation and experiment on a laboratory prototype.

Hydrologic models are conventionally constrained and evaluated using point measurements of streamflow, which represents an aggregated catchment measure. As a consequence of this single objective focus, model parametrization and model parameter sensitivity are typically not reflecting other aspects of catchment behavior. Specifically for distributed models, the spatial pattern aspect is often overlooked. Our paper examines the utility of multiple performance measures in a spatial sensitivity analysis framework to determine the key parameters governing the spatial variability of predicted actual evapotranspiration (AET). Latin hypercube one-at-a-time (LHS-OAT) sampling strategy with multiple initial parameter sets was applied using the mesoscale hydrologic model (mHM) and a total of 17 model parameters were identified as sensitive. The results indicate different parameter sensitivities for different performance measures focusing on temporal hydrograph dynamics and spatial variability of actual evapotranspiration. While spatial patterns were found to be sensitive to vegetation parameters, streamflow dynamics were sensitive to pedo-transfer function (PTF) parameters. Above all, our results show that behavioral model definition based only on streamflow metrics in the generalized likelihood uncertainty estimation (GLUE) type methods require reformulation by incorporating spatial patterns into the definition of threshold values to reveal robust hydrologic behavior in the analysis.

Evidence-based healthcare integrates the best research evidence with clinical expertise in order to make decisions based on the best practices available. In this context, the task of collecting all the relevant information, a recall oriented task, in order to take the right decision within a reasonable time frame has become an important issue. In this paper, we investigate the problem of building an effective Consumer Health Search (CHS) systems that use query variations to achieve high recall and fulfill the information needs of health consumers. In particular, we study an intent-aware gain metric used to estimate the amount of missing information and make a prediction about the achievable recall for each query reformulation during a search session. We evaluate and propose alternative formulations of this metric using standard test collections of the CLEF 2018 eHealth Evaluation Lab CHS.

We discuss the electrodeposition of two-dimensional (2D) Pt-nanostructures on HOPG achieved under constant applied potential versus a Pt counter electrode (Eappl = ca. - 2.2 V vs RHE). The deposition conditions are discussed in terms of the electrochemical behavior of the electrodeposition precursor (H2PtCl6). We performed cyclic voltammetry (CV) of the electrochemical Pt deposit on HOPG and on Pt substrates to study the relevant phenomena that affect the morphology of Pt deposition. Under conditions where the Pt deposition occurs and H2 evolution is occurring at the diffusion-limited rate (- 0.3 V vs RHE), Pt forms larger structures on the surface of HOPG, and the electrodeposition of Pt is not limited by diffusion. This indicates the need for large overpotentials to direct the 2D growth of Pt. Investigation of the possible effect of Cl- showed that Cl- deposits on the surface of Pt at low overpotentials, but strips from the surface at potentials more positive than the electrodeposition potential. The CV of Pt on HOPG is a strong function of the nature of the surface. We propose that during immersion of HOPG in the electrodeposition solution (3 mM H2PtCl6, 0.5 M NaCl, pH 2.3) Pt islands are formed spontaneously, and these islands drive the growth of the 2D nanostructures.

Internet-led labour market has become so competitive forcing many organisations from different sectors to embrace e-recruitment. However, realising the value of the e-recruitment from a Requirements Engineering (RE) analysis perspective is challenging. This research is motivated by the results of a failed e-recruitment project conducted in military domain which is used as a case study in this research. After reviewing the various challenges faced in that project through a number of related research domains, this research focuses on two major problems which are the (1) difficulty of scoping, representing, and systematically transforming recruitment problem knowledge towards e-recruitment solution specification; and (2) the difficulty of documenting e-recruitment best practices for reuse purposes in an enterprise recruitment environment. In this paper, a Problem-Oriented Conceptual Model (POCM) with a complementary Ontology for Recruitment Problem Definition (Onto-RPD) is proposed to contextualise the various recruitment problem viewpoints from an enterprise perspective and to elaborate those problem viewpoints towards a comprehensive recruitment problem definition. The POCM and Onto-RPD are developed incrementally using action-research conducted on three real case studies: (1) Secureland Army Enlistment, (2) British Army Regular Enlistment, and (3) UK Undergraduate Universities and Colleges Admissions Service (UCAS). They are later evaluated in a focus group study against a set of criteria. The study showed that the POCM and Onto-RPD provide a strong foundation for representing and understanding the e-recruitment problems from different perspectives.

Discrete distribution estimation is a fundamental statistical tool, which is widely used to perform data analysis tasks in various applications involving sensitive personal information. Due to privacy concerns, individuals may not always provide their raw information, which leads to unpredictable biases in the final results of estimated distribution. Local Differential Privacy (LDP) is an advanced technique for privacy protection of discrete distribution estimation. Currently, typical LDP mechanisms provide same protection for all items in the domain, which imposes unnecessary perturbation on less sensitive items and thus degrades the utility of final results. Although, several recent works try to alleviate this problem, the utility can be further improved. In this paper, we propose a novel notion called Item-Oriented Personalized LDP (IPLDP), which independently perturbs different items with different privacy budgets to achieve personalized privacy protection. Furthermore, to satisfy IPLDP, we propose the Item-Oriented Personalized Randomized Response (IPRR) based on the observation that the sensitivity of data shows an inverse relationship with the population size of respective individuals. Theoretical analysis and experimental results demonstrate that our method can provide fine-grained privacy protection and improve data utility simultaneously.

The notion of oriented set is the basic elementary concept of the theory of changeable sets. The main motivation for the introduction of changeable sets was the sixth Hilbert problem, that is, the problem of mathematically rigorous formulation of the fundamentals of theoretical physics. In the present paper the necessary and sufficient condition of the existence of one-point time on an oriented set is established. From the intuitive point of view, one-point time is the time associated with the evolution of a system consisting of only one object (for example, from one material point). Namely, it is proven that the one-point time exists on the oriented set if and only if this oriented set is a quasi-chain. Also, using the obtained result, the problem of describing all possible images of linearly ordered sets is solved. This problem naturally arises in the theory of ordered sets.

Constitutive models for plastic deformation of metals are typically based on flow rules determining the transition from elastic to plastic response of a material as function of the applied mechanical load. These flow rules are commonly formulated as a yield function, based on the equivalent stress and the yield strength of the material, and its derivatives. In this work, a novel mathematical formulation is developed that allows the efficient use of machine learning algorithms describing the elastic-plastic deformation of a solid under arbitrary mechanical loads and that can replace the standard yield functions with more flexible algorithms. By exploiting basic physical principles of elastic-plastic deformation, the dimensionality of the problem is reduced without loss of generality. The data-oriented approach inherently offers a great flexibility to handle different kinds of material anisotropy without the need for explicitly calculating a large number of model parameters. The applicability of this formulation in finite element analysis is demonstrated, and the results are compared to formulations based on Hill-like anisotropic plasticity as reference model. In future applications, the machine learning algorithm can be trained by hybrid experimental and numerical data, as for example obtained from fundamental micromechanical simulations based on crystal plasticity models. In this way, data-oriented constitutive modeling will also provide a new way to homogenize numerical results in a scale-bridging approach.

CO2 flooding stands as a pivotal technique for significantly enhancing oil recovery in low-permeability reservoirs. The movement and sweeping rules at the front of CO2 flooding play a critical role in its oil recovery, yet a comprehensive quantitative analysis remains an area in need of refinement. In this study, we have developed 1D and 2D numerical simulation models to explore the sweeping behavior of miscible, immiscible, and partly-miscible CO2 flooding patterns. The front position and movement rules of the three CO2 flooding patterns are determined. A novel approach of the contour area calculation method is introduced to quantitatively characterize the sweep coefficients, and the sweeping rules are discussed regarding geological parameters, oil viscosity, and injection-production parameters. Furthermore, the Random Forest (RF) algorithm is employed to identify the controlling factor of the sweep coefficient, as determined by out-of-bag (OOB) data displacement analysis. The results show that the miscible front is located at the point of maximum CO2 content in the oil phase. The immiscible front occurs at the point of maximum interfacial tension near the production well. Remarkably, the immiscible front moves at a faster rate compared to the miscible front. Geological parameters, including porosity, permeability, and reservoir thickness, significantly impact the gravity segregation effect, thereby influencing the CO2 sweep coefficient. Immiscible flooding exhibits the highest degree of gravity segregation, with a maximum gravity segregation degree (GSD) reaching 78.1. The permeability ratio is a crucial factor, with a lower limit of approximately 5.0 for reservoirs suitable for CO2 flooding. Injection-production parameters also play a pivotal role in sweep coefficient. Decreased well spacing and increased gas injection rates are found to enhance sweep coefficients by suppressing gravity segregation. Additionally, higher gas injection rates can improve the miscibility degree of partly-miscible flooding from 0.69 to 1.0. Oil viscosity proves to be a significant factor influencing the sweep coefficients, with high seepage resistance due to increasing oil viscosity dominating the miscible and partly-miscible flooding patterns. Conversely, gravity segregation primarily governs the sweep coefficient in immiscible flooding. In terms of controlling factors, the permeability ratio emerges as a paramount influence, with a factor importance value (FI) reaching 1.04. these results provide a theoretical foundation for the application of CO2 flooding, enhancing the understanding of the critical factors governing its success.

tructural and superconducting properties of high quality Niobium nanofilms with different thicknesses are investigated on silicon oxide and sapphire substrates. The role played by the different substrates and the superconducting properties of the Nb films are discussed based on the defectivity of the films and on the presence of an interfacial oxide layer between the Nb film and the substrate. The X-ray absorption spectroscopy is employed to uncover the structure of the interfacial layer. We show that this interfacial layer leads to a strong proximity effect, specially in films deposited on a SiO2 substrate, altering the superconducting properties of the Nb films. Our results establish that the critical temperature is determined by an interplay between quantum-size effects, due to the reduction of the Nb film thicknesses, and proximity effects.

This paper presents an alternative process to fabricate flexible bandpass filters by using embroidered yarn conductor on electronic-textile. The novelty of the proposed miniaturized filter is its complete integration on the outfit, with benefits in terms of compressibility, stretch ability and high geometrical accuracy, opening the way to develop textile filters in sport and medicine wearable applications. The proposed design consists of a fully embroidered microstrip topology with a length equal to quarter wavelength (λ/4) to develop a bandpass filter frequency response. A drastic reduction in size of the filter was achieved by taking advantage of a simplified architecture based on meandered-line stepped impedance resonator. The e-textile microstrip filter has been designed, simulated, fabricated and measured, with experimental validation at a 7.58 GHz frequency. The insertion loss obtained by simulation of the filter is substantially small. The return loss is greater than 20 dB for bands. To explore the relations between physical parameters and filter performance characteristics, theoretical equivalent circuit model of the filter constituent components were studied. The effect of bending of the e-textile filter is also studied. The results show that by changing the radius of bending up to 40 mm, the resonance frequency is shifted up 4.25 MHz/mm.

Robot workpiece machining is interesting in industry since it offers some advantages, such as higher flexibility in comparison with the conventional approach based on the CNC technology. However, in recent years we have been facing a strong progressive shift to custom based manufacturing and low volume/high mix production, which require a novel approach to automation by the employment of collaborative robotics. However, collaborative robots feature only limited motion capability, to provide safety in cooperation with human workers. Thus, it is highly necessary to perform more detailed robot task planning to ensure its feasibility and optimal performance. In this paper, we deal with the problem of studying kinematic robot performance in the case of such manufacturing tasks, where the robot tool is constrained to follow the machining path embedded on the workpiece surface at a prescribed orientation. The presented approach is based on the well-known concept of manipulability, although the latter suffers from physical inconsistency due to mixing different units of linear and angular velocity in a general 6 DOF task case. Therefore, we introduce the characteristics of the workpiece surface constraint in the robot kinematic analysis, that enables evaluation of its available velocity capability in a reduced dimension space. Such constrained robot kinematics transform the robot`s task space to a two-dimensional surface tangent plane, and the manipulability analysis may be limited to the space of linear velocity only. Thus, the problem of physical inconsistency is avoided effectively. We show the theoretical derivation of the proposed method, which was verified by numerical experiments.

Rapid advancements in the fifth generation (5G) communication technology and mobile edge computing (MEC) paradigm lead to the proliferation of unmanned aerial vehicles (UAV) in urban air mobility (UAM) networks, which provide intelligent services for diversified smart city scenarios. Meanwhile, the widely deployed internet of drones (IoD) in smart cities also brings up new concerns on performance, security, and privacy. The centralized framework adopted by conventional UAM networks is not adequate to handle high mobility and dynamicity. Moreover, it is necessary to ensure device authentication, data integrity, and privacy preservation in UAM networks. Thanks to characteristics of decentralization, traceability, and unalterability, Blockchain is recognized as a promising technology to enhance security and privacy for UAM networks. In this paper, we introduce LightMAN, a lightweight microchained fabric for data assurance and resilience-oriented UAM networks. LightMAN is tailored for small-scale permissioned UAV networks, in which a microchain acts as a lightweight distributed ledger for security guarantees. Thus, participants are enabled to authenticate drones and verify the genuineness of data that is sent to/from drones without relying on a third-party agency. In addition, a hybrid on-chain and off-chain storage strategy is adopted that not only improves performance (e.g,.latency and throughput) but also ensures privacy preservation for sensitive information in UAM networks. A proof-of-concept prototype is implemented and tested on a Micro Air Vehicle Link (MAVLink) simulator. The experimental evaluation validates the feasibility and effectiveness of the proposed LightMAN solution.

Organic compounds that contain poly-triazole are very important intermediates in pharmaceutical and chemical industry. Click chemistry is one of essential reactions that can form C-N bond with high atom economy. The research progress in metals catalyzed Click chemistry of azides and alkynes from the perspective of reaction mechanism is categorized and summarized.

We propose a probabilistic graphical model for discriminative substrate characterization, to support geological and biological habitat mapping in aquatic environments. The model, called a fully connected conditional random field (CRF), is demonstrated using multispectral and monospectral acoustic backscatter from heterogeneous seafloors in Patricia Bay, British Columbia, and Bedford Basin, Nova Scotia. Unlike previously proposed discriminative machine learning algorithms, the CRF model considers both the relative backscatter magnitudes of different substrates and their relative proximities. The model therefore combines the statistical flexibility of a machine learning algorithm with an inherently spatial treatment of the substrate. The CRF model predicts substrates such that nearby locations with similar backscattering characteristics are likely to be in the same substrate class. The degree of proximity and allowable backscatter similarity are controlled by parameters that are learned from the data. CRF model results were evaluated against a popular generative model known as a Gaussian Mixture model that doesn't include spatial dependencies, only covariance between substrate backscattering response over different frequencies. Both models are used in conjunction with sparse bed observations/samples in a supervised classification. A detailed accuracy assessment, including a leave-one-out cross-validation analysis, was performed using both models. Using multispectral backscatter, the GMM model trained on 50% of the bed observations resulted in a 75% and 89% average accuracies in Patricia Bay and Bedford Basin, respectively. The same metrics for the CRF model were 78% and 95%. Further, the CRF model resulted in a 91% mean cross-validation accuracy across four substrate classes at Patricia Bay, and a 99.5% mean accuracy across three substrate classes at Bedford Basin, which suggest that the CRF model generalizes extremely well to new data. This analysis also showed that the CRF model was much less sensitive to the specific number and locations of bed observations than the generative model, owing to its ability to incorporate spatial autocorrelation in substrates. The CRF approach therefore may prove to be a powerful `spatially aware' alternative to other discriminative classifiers.

This paper presents a cascade predictive control structure based on the field-oriented control (FOC) in the dq rotor reference frame for the synchronous reluctance machine (SynRM). The constant d-axis current control strategy was used and thus, the electromagnetic torque was directly controlled by the q-axis current. Because the model of the two axes currents from the inner loop is a coupled non-linear multivariable one, to non-interaction linear control the two currents, their decoupling was achieved through feedforward components. Following the decoupling, two independent monovariable linear systems resulted for the two currents dynamics that were controlled using model predictive control (MPC) algorithms, considering their ability to automatically handle the state bounds. The most important bounds for SynRM are the limits imposed on currents and voltages, which in the dq plane correspond to a circular limit. To avoid computational effort, linear limitations were adopted through polygonal approximations, resulting in rectangular regions in the dq plane. For the outer loop that controls the angular speed with a constrained MPC algorithm, as plant was considered the q-axis current closed loop dynamics and the torque linear equation. To evaluate the performances of the proposed cascade predictive control structure, a simulation study using MPC controllers versus PI ones was conducted.

Optimization using Genetic Algorithms (GA) is a well-known strategy in several scientific disciplines. The crossover is an essential operator of the Genetic Algorithm. It has been an active area of research to develop sustainable forms for this operand. In this work, a new crossover operand is proposed. This operand depends on giving an elicited description for the chromosome with a new structure for alleles of the parents. It is suggested that each allele has two attitudes, one attitude differs contrastingly with the other, and both of them complement the allele. Thus, in case of one attitude is good, the other should be bad. This is suitable for many systems which contain admired parameters and unadmired parameters. The proposed crossover would improve the desired attitudes and damp the undesired attitudes. The proposed crossover can be achieved in two stages: the first stage is a mating method for both attitudes in one parent to improving one attitude at the expense of the other. The second stage comes after the first improvement stage for mating between different parents. Hence, two concurrent steps for improvement would be applied. Simulation experiments for the system shows improvement in the fitness function. The proposed crossover could be helpful in different fields, especially to optimize routing algorithms and network protocols, an application that has been tested as a case study in this work.

As a system becomes more complex, at first, its description and analysis becomes more complicated. However, a further increase in the system’s complexity often makes this analysis simpler. A classical example is Central Limit Theorem: when we have a few independent sources of uncertainty, the resulting uncertainty is very difficult to describe, but as the number of such sources increases, the resulting distribution get close to an easy-to-analyze normal one – and indeed, normal distributions are ubiquitous. We show that such limit theorems make analysis of complex systems easier – i.e., lead to blessing of dimensionality phenomenon – for all the aspects of these systems: the corresponding transformation, the system’s uncertainty, and the desired result of the system’s analysis.

Henry Vidal first introduced the concept of using strips, grids, and sheets for reinforcing soil masses. Since then, a large variety of materials such as steel bars, tire shreds, polypropylene, polyester, glass fibers, coir, jute fibers etc. have been widely added to the soil mass randomly or in a regular, oriented manner. In this investigation, a new concept of multi-oriented plastic reinforcement (hexa-pods), is discussed. A systematic and comprehensive laboratory tests were conducted on unreinforced and reinforced soil samples. Laboratory tests such as direct shear teat and California bearing ratio (CBR) test were analyzed on soil samples consisting of only soil samples, soil sample with random inclusion of hexapods and soil samples with layered inclusion of hexapods. From the results obtained through direct shear test it could be observed that cohesion value of both the soil sample has increased and the angle of internal friction has been decreased after reinforcing it with inclusions in both randomly and layered conditions. CBR test indicates that for same amount of compactive effort, both random and layered inclusions of hexapods show improvement in strength and stiffness. Random inclusions of hexapods give better resistance to penetration as compared to layered inclusions. The hexa-pods also changed the brittle behavior of unreinforced sand samples to ductile ones.

Autonomous and cooperative vehicle systems represent a key priority in the automotive realm. Networked driving simulation can be utilized as a safe, cost-effective experimental replica of real traffic environments in order to support and accelerate the development of such systems. In networked driving simulation, different independent systems collaborate to achieve a common task: multi-driver traffic scenario simulation. Yet distinct system complexity levels are necessary to fulfill the requirements of various application scenarios, such as development of vehicle systems, analysis of driving behavior, and training of drivers. With myriad alternatives of available systems and components, developers of networked driving simulation are typically confronted with high design complexity. There are no systematic approaches to date for the design of networked driving simulation in accordance with the specific requirements of the concerned application scenarios. This paper presents a novel design method for networked driving simulation. The method consists mainly of a procedure model that is accompanied by a configuration software. The procedure model includes the necessary phases for the systematic design of application-oriented platforms for networked driving simulation. The configuration software embeds supportive decision-making processes that enable developers to apply the design method and easily create different system models. The design method was validated by generating system models and developing platforms of networked driving simulation for three different application scenarios.

The bending performance of a basalt-polypropylene fiber-reinforced concrete (HBPFRC) was characterized by testing 24 400×100×100 mm3 prismatic specimens in a four-point bending test JSCE-SF4 configuration. The type and content of both fibers was varied in order to guarantee different target levels of post-cracking flexural performance. The results evidenced that mono-micro basalt fiber reinforced concrete (BFRC) allows the increase of the flexural strength (pre-cracking stage), while macro polypropylene fiber reinforced concrete can effectively improve both bearing capacity and ductility of the composite for a wide crack width range. Compared with the plain concrete specimens, flexural toughness and equivalent flexural strength of macro polypropylene fiber-reinforced concrete (PPFRC) and the hybrid fiber-reinforced concrete (HFRC) increased by 3.7~7.1 times and 10%~42.5%, respectively. From both technical and economic points of view, the optimal mass ratio of basalt fiber to polypropylene fiber resulted to be 1:2, with a total content of 6 kg/m3. This HFRC is seen as a suitable material to be used in sewerage pipes where cracking control (crack formation and crack width control) is of paramount importance to guarantee the durability and functionality of the pipeline as well as the ductility of the system in case of local failures.

Sars-CoV-2 outbreak represents a public health emergency, affecting different regions of the world. Lung is the organ more damaged due to the high presence of Sars-CoV-2 binding receptor ACE2 on epithelial alveolar cells. Severity of infection vary from absence of symptomatology to be more severe, characterized by acute respiratory distress syndrome (ARDS), multiorgan failure and sepsis requiring treatment in Intensive Care Unit (ICU).It is not still clear why in a small percentage of patients immune system is not able to efficiently suppress viral replication. It has been documented as predictive factors for severity and susceptibility affections of cardiovascular system such as heart failure (HF), coronary heart disease (CHD) and risk factors for atherosclerotic progression, hypertension and diabetes among others.Atherosclerotic progression, as chronic inflammation process, is characterized by immune system dysregulation leading to pro-inflammatory pattern, including (Interleukin 6) IL-6, Tumor Necrosis Factor α (TNF-α) and IL-1β raise. Reviewing immune system and inflammation profiles in atherosclerosis and laboratory results report in severe Sars-CoV-2 infection we have supposed a pathogenetic correlation. Atherosclerosis may be a pathogenetic ideal substrate to high viral replication ability leading to adverse outcomes, how reported in patients with cardiovascular factors. Moreover, level of atherosclerotic progression may impact on a different degree of severe infection and in a vicious circle feeding itself Sars-CoV-2 may exacerbate atherosclerotic progression due to excessive and aberrant plasmatic concentration of cytokines.

Hymenaea courbaril is an endangered species, promising to reforestation programs and mainly explored as a wood source. The available information concerning long-term storage methods, seed recalcitrance, parental, and substrate influence is scarce. This study focused on the seed behavior according to population origin and during one-year storage, also testing the efficiency of the low-temperature conservation. Variations between the uncertainty indexes were found to the studied populations after long-term storage. There was no significant loss of the germination potential in consequence of the prolonged storage period. Although, older seeds promoted gradually greater delayed germination. Germination speed, synchrony, and uncertainty indexes were substantially different between the -20° conservation and control. H. courbaril seeds are capable of long-term storage without losing their germination potential, indicating an orthodox behavior.

Oral and parenteral delivery of first-line anticonvulsant Valproic cid (VA) are associated with serious adverse effects, high hepatic metabolism, high clearance, and low bioavailability in brain. GastroPlus program was used to predict in vivo performance of immediate (IR) and sustained release (SR) products in human. HSPiP software predicted excipients with maximum possible miscibility of the drug. Based on GastroPlus and HSPiP program, various excipients were screened for experimental solubility study and prepared cationic nanoemulsions and respective gels for nasal to brain delivery. These were characterised for size, size distribution, polydispersity index, zeta potential, morphology, pH, % transmittance, drug content, and viscosity. In vitro drug release, ex vivo permeation profile (goat nasal mucosa), and penetration studies were conducted. Result showed that in-vivo oral drug dissolution and absorption were predicted as 98.6 mg and 18.8 mg, respectively from both tablets (IR and SR) at 8 h using GastroPlus. The drug access to the portal vein was relatively predicted high in IR (115 mg) as compared to SR (82.6 mg). Plasma drug concentration-time profile predicted was in good agreement with published reports. The program predicted duodenum and jejunum as the prime site of drug absorption and no effect of nanonization on Tmax for sustained release formulation. Hansen parameters suggested suitable selection of excipients. The program recommended for nasal to brain delivery of the drug using cationic mucoadhesive product. The optimized stable CVE6 was associated with optimal size (113 nm), low PDI (0.26), high zeta potential (+34.7 mV), high transmittance (97.8%), and high strength (0.7 %w/w). In vitro release and ex vivo permeation of CVE6 were found to be substantially high as compared to anionic AVE6 and respective gels. Penetration study executed high fluorescence intensity with CVE6 and CVE6-gel as compared to suspension and ANE6 which may be attributed to electrostatic interaction between mucosal membrane and nanoglobules. Thus, cationic nanoemulsion and respective mucoadhesive gel are promising strategy for delivery of VA to brain through intransal administration for the treatment of seizure and convulsion.

In industry 4.0 era, video applications such as surveillance visual systems, video conferencing, or video broadcasting have been playing a vital role. In these applications, for manipulating and tracking objects in decoded video, the quality of decoded video should be consistent because it largely affects to the performance of the machine analysis. To cope with this problem, we propose a novel perceptual video coding (PVC) solution in which a full reference quality metric named Video Multimethod Assessment Fusion (VMAF) is employed together with a deep convolutional neural network (CNN) to obtain the consistent quality while still achieving the high compression performance. First of all, to achieve the consistent quality requirement, we propose a CNN model with an expected VMAF as input to adaptively adjust the quantization parameters (QP) for each coding block. Afterwards, to increase the compression performance, a Lagrange coefficient of Rate-Distortion optimization (RDO) mechanism is adaptively computed under Rate-QP and Quality-QP models. Experimental results show that the proposed PVC has achieved two targets simultaneously: the quality of video sequence is kept consistently with an expected quality level and the bit rate saving of the proposed method is higher than traditional video coding standards and relevant benchmark, notably with around 10% bitrate saving in average.

Pavement friction plays a crucial role in ensuring the safety of road networks. Accurately assessing friction levels is vital for effective pavement maintenance and management strategies employed by state highway agencies. Traditionally, friction evaluations have been conducted on a case-by-case basis, focusing on specific road sections. However, this approach fails to provide a comprehensive assessment of friction conditions across the entire road network. This paper introduces a hybrid clustering algorithm, namely the combination of density-based spatial clustering of applications with noise (DBSCAN) and Gaussian mixture model (GMM), to perform pavement friction performance rating across a statewide road network. A large, safety-oriented dataset is first generated by integrating network friction and vehicle crash data based on the attributes contributing possibly to friction related crashes. One-, two-, and multi-dimensional clustering analyses, respectively, are then performed to rate pavement friction. The Chi-square test is further employed to validate and identify the practical ratings. It is shown that by effectively capturing the hidden, intricate patterns within the integrated, complex dataset and prioritizing friction-related safety attributes, the hybrid clustering algorithm can produce pavement friction ratings that align effectively with the current practices of the Indiana Department of Transportation (INDOT) in friction management.

Visual Patient technology is a situation awareness–oriented visualization technology that translates numerical and waveform patient monitoring data into a new user-centered visual language. Vital sign values are converted into colors, shapes, and rhythmic movements—a language humans can easily perceive and interpret—on a patient avatar model in real time. In this review, we summarize the current state of the research on the Visual Patient, including the technology, its history, and its scientific context. We also provide a summary of our primary research and a brief overview of research work on similar user-centered visualizations in medicine. In several computer-based studies under various experimental conditions, Visual Patient transferred more information per unit time, increased perceived diagnostic certainty, and lowered perceived workload. Eye tracking showed the technology worked because of the way it synthesizes and transforms vital sign information into new and logical forms corresponding to the real phenomena. The technology could be particularly useful for improving situation awareness in settings with high cognitive demand or when users must make quick decisions. This comprehensive review of Visual Patient research is the foundation for an evaluation of the technology in clinical applications, starting with a high-fidelity simulation study in early 2020.

The inositol triphosphate associated proteins IRAG1 and IRAG2 are cGMP kinase substrate proteins, which regulate intracellular Ca2+. Previously, IRAG1 was discovered as a 125 kDa membrane protein at the endoplasmic reticulum, that is associated with the intracellular Ca2+ channel IP3R-I and the PKGIβ and inhibits IP3R-I upon PKGIβ-mediated phosphorylation. IRAG2 is a 75 kDa membrane protein homologue of IRAG1 and was recently also determined as a PKGI substrate protein. Several (patho-)physiological functions of IRAG1 and IRAG2 were meanwhile and recently elucidated in a variety of human and murine tissues, e.g. of IRAG1 in various smooth muscles, heart, platelets and other blood cells, of IRAG2 in pancreas, heart, platelets and taste cells. Hence, lack of IRAG1 or IRAG2 leads to diverse phenotypes in these organs, e.g. smooth muscle and platelet disorders or secretory deficiency, respectively. This review aims to highlight the recent research regarding these both regulatory proteins to envision its molecular and (patho-)physiological tasks and to unravel its functional interplay as possible (patho-)physiological counterparts.

The reflection and transmission spectra of a metamaterial formed by omega-shaped elements with pre-calculated optimal parameters on a silicon substrate have been recorded in the terahertz range at oblique incidence for the s- and p- polarizations of the incident wave. The spectra were interpreted within the dipole radiation theory of electromagnetic waves. Both measurement results and analysis provide evidence sup-porting the presence of a pronounced polarization anisotropy impact in the reflection and transmission of the metamaterial. The potential of these materials to be utilized in the development of devices that control the polarization properties of THz radiation across a wide spectral range is examined.

In order to understand the genetic diversity of germplasm resources of kumquat in Guangxi, 14 kumquat germplasm resources in Guangxi and 12 accessions from other provinces were analyzed by using SRAP markers. In total, 19 primer pairs with high stability, good reproducibility, and high polymorphism were chosen for analysis of all the 26 kumquat genotypes. Among the 101 amplified bands, 87 (86.14%) were polymorphic. SRAP markers were analyzed by employing Principal Coordinate Analysis, Population Structure Analysis and Hierarchical Cluster Analysis (UPGMA). The classification results showed that 26 kumquat germplasm could be divided into 5 groups, including cultivated kumquat, intergeneric hybrid, wild kumquat from other provinces, wild kumquat from Guangxi and hybrid kumquat from Guangxi. Guangxi kumquat germplasm occurred high genetic diversity, which were clearly divided into 3 groups like cultivated kumquat, wild kumquat and kumquat hybrid. And the 8 cultivated kumquat varieties in Guangxi were further divided into two subgroups. Wild kumquat in Guangxi and wild kumquat in other provinces belong to different groups, meanwhile the hybrids of Guangxi kumquat form independent groups, thus indicated that Guangxi wild kumquat and kumquat hybrid possessed certain specificity, or they maybe belonged to different species. Among the tested 26 kumquat accessions, 23 unique genotype-specific SRAP markers were detected for 14 kumquat genotypes, which made it possible to surely identify them. For the remaining 12 accessions without genotype-specific markers, they were distinguished by various combinations of markers. These results may have certain importance for kumquat genetic research and cultivar selection.

Oriented object detection is a challenging task in scene text detection and remote sensing image analysis, which has attracted extensive attention in recent years with the development of deep learning. Currently, mainstream oriented object detectors are based on preset anchor boxes. This method increases the computational load of the network and cause a large amount of anchor box redundancy. To solve this problem, we propose anchor-free oriented object detection based on the Gaussian centerness(AOGC), a single-stage anchor-free detection method. Our method uses contextual attention FPN(CAFPN) to obtain the contextual information of the target. Then we design a label assignment method for oriented objects. Finally, we develop a Gaussian kernel-based centerness branch, which can effectively determine the significance of different anchors. AOGC achieves mAP of 74.30% on the DOTA-1.0 datasets and 89.80% on the HRSC2016 datasets, respectively. AOGC exhibits superior performance to other methods in oriented anchor-free object detection methods.

Background: In Transcranial Direct Current Stimulation (tDCS) the injected current gets distributed across the brain areas. The motive is to stimulate the target region-of-interest (ROI), while minimizing the current in non-target ROIs. For this purpose, determining the appropriate current-dose for an individual is difficult. Aim: To introduce Dose-Target-Determination-Index (DTDI) to quantify the focality of tDCS and examine the dose-focality relationship in three different populations. Method: Here, we extended our previous toolbox i-SATA to the MNI reference space. After a tDCS montage is simulated for a current-dose, the i-SATA(MNI) computes the average (over voxels) current density for every region in the brain. DTDI is the ratio of average current density at target ROI to the ROI with maximum value (peak region). Ideally target ROI should be the peak region, so DTDI shall range from 0 to 1. Higher the value, the better the dose. We estimated the variation of DTDI within and across individuals using T1-weighted brain images of 45 males and females distributed equally across three age groups- (a) Young adults (20 ≥ x ˂ 40 years), (b) Mid adults (40 ≥ x ˂ 60 years), and (c) Older adults (60 ≥ x ˂ 80 years). DTDI’s were evaluated for the frontal montage with electrodes at F3 and right supra-orbital for three current doses 1mA, 2mA, and 3mA with the target ROI at left middle frontal gyrus. Result: As the dose is incremented, DTDI may show (a) increase, (b) decrease, and (c) no change across the individuals. The focality decreases with age and the decline is stronger in males. Higher current dose at older age can enhance the focality of stimulation. Conclusion: DTDI provides information on which tDCS current dose will optimize the focality of stimulation. DTDI recommended dose should be prioritised based on the age (> 40 years) and sex (especially males) of an individual. The toolbox i-SATA(MNI) is freely available.

Mathematical literacy is a very hot issue in the development of mathematics learning, apart from mathematical literacy, another interesting thing is the entrepreneurial spirit that must be given from an early age, especially for vocational students. This research was conducted at SMK Rosma Karawang in the Department of Computer and Network Engineering, West Java Province with the XI grade students. The teaching materials developed by applying the principles of the development model developed with the ADDIE model consist of analysis, design, development, implementation and evaluation. This research and development model is considered suitable for developing teaching tools and materials which is used for the purposes of the learning process. Based on the results of data analysis and processing that have been carried out in this study, the development of teaching materials using the ADDIE model has met the appropriate and valid criteria by media, language and media expert valuators. Another result of developing this teaching material besides meeting the eligibility criteria is that the teaching materials developed are able to increase mathematical literacy and instill entrepreneurial spirit for students.

Crosslinking of proteins for their irreversible immobilization on surfaces is a proven and popular method. However, many protocols lead to random orientation and the formation of undefined or even inactive by-products. Most concepts to obtain a more targeted conjugation or immobilization requires the recombinant modification of at least one binding partner, which is often impractical or prohibitively expensive. Here a novel method is presented, which is based on the chemical preactivation of Protein A or G with selected conventional crosslinkers. In a second step, the antibody is added, which is subsequently crosslinked in the Fc part. This leads to an oriented and covalent immobilization of the immunoglobulin with a very high yield. Protocols for Protein A and Protein G with murine and human IgG are presented. This method may be useful for the preparation of columns for affinity chromatography, immunoprecipitation, antibodies conjugated to magnetic particles, permanent and oriented immobilization of antibodies in biosensor systems, microarrays, microtitration plates or any other system, where the loss of antibodies needs to be avoided, and maximum binding capacity is desired. This method is directly applicable even to antibodies in crude cell culture supernatants, raw sera or protein-stabilized antibody preparations without any purification nor enrichment of the IgG. This new method delivered much higher signals as a traditional method and, hence, seems to be preferable in many applications.

Most of the research of mental fatigue evaluation mainly concentrated on some indexes that require sophisticate and large instruments which make the detection of mental fatigue cumbersome, time-consuming, and difficult to apply on a large scale. A quick and sensitive mental fatigue detection index is necessary so that mental workers can be alerted in time and take corresponding countermeasures. But to date, no studies have compared the sensitivity of common objective evaluation indexes. To solve these problems this study recruited 56 human subjects. These subjects were evaluated using six fatigue indexes: the Stanford sleepiness scale, digital span, digital decoding, short-term memory, critical flicker fusion frequency (CFF), and speed perception deviation. The results of fatigue tests before and after mental fatigue were compared, and a one-way analysis of variance (ANOVA) was performed on the speed perception deviation. The result indicated the significance of this index. Considering individual differences, the relative fatigue index (RFI) was proposed to compare the sensitivity of the indexes. The results showed that when the self-rated fatigue grade changed from non-fatigue to mild fatigue, the ranges of RFI values for digital span, digital decoding, short-term memory and CFF were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. Correspondingly, when the self-rated fatigue grade changed from non-fatigue to severe fatigue, the ranges of RFI values for the above indexes were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. These results suggest that the sensitivity of the digital decoding, digital span, short-term memory, and CFF decreased sequentially when the self-evaluated fatigue grade changed from no fatigue to mild or severe fatigue. The RFI individuality of the speed perception deviation is highly variable and is not suitable as an evaluation index. In mental fatigue testing, digital decoding testing can provide faster, more convenient, and more accurate results.

In airborne sensor networks (ASNs), the media access control (MAC) protocol is facing with serious unfairness problem due to the traditional protection mechanism of air-to-air communications among aircrafts. Actually by using the binary exponential back-off algorithm at high traffic loads to minimize collisions among users, the latest successful node can always benefit from this kind of MAC to obtain channel resources. Moreover, when taking the existence of the hidden nodes in ASNs into account, the inaccurate traffic load information will further aggravate the system’s unfairness. In this paper, a neighbor-channel-aware (NCA) protocol is proposed to improve the fairness of MAC protocol in ASNs. In the proposal, the NCA frame is firstly added and exchanged between neighbor nodes periodically, which helps to resolve the inaccurate traffic load information, so as to avoid reducing the probability of successful message transmission. Then a traffic-loading based back-off algorithm is involved to make the neighbor nodes cooperatively adjust the inter-frame space (IFS) interval to further reduce the unfairness. The simulation results show that, the proposed MAC protocol can guarantee the satisfied fairness, simultaneously avoiding heavy network overloads to protect key messages’ successful transmissions in ASNs.

Extensive green roofs provide for many ecosystem services in urban environments. The efficacy of these services is influenced by the substrate characteristics and vegetational composition. Despite their key role in plant performance and productivity, or their contribution to nitrogen fixation or carbon sequestration, green roof microbial communities have received little attention so far. Here, we investigated whether microbial communities in extensive green roof substrates contain a core community, as well as whether they are affected by green roof plant diversity. Eleven green roofs, planted either with a mixture of grasses, wildflowers and succulents (Sedum spp.), or solely species of Sedum, were seasonally sampled to investigate prokaryotic and fungal communities via metabarcoding. Although Sedum-herbs-grasses roofs contained more plant species, we observed no discriminant microbial communities between both roof types, likely due to sharing the same substrate textures and the vegetational layers that became more similar throughout time. Examining key microbial taxa revealed that most taxa are also dominant phylotypes in soils across different biomes. Many bacterial core taxa are capable of nitrogen fixation and most fungal key taxa are stress-tolerant saprotrophs, endophytes, or both. Microbial community composition further revealed high similarities with aerial samples taken in urban environments. Considering the extreme edaphic conditions that periodically arise in green roof substrates, further investigation is warranted to determine the extent to which the dynamic and intriguing microbial communities are influenced by the aeromicrobiome.

Sr4Al6O12SO4 samples were obtained from the compound mixture formed by a solid–state reaction of Al2O3, SrSO4, and SrCO3. Samples were compacted at 100MPa to form pellets of 1 and 4cm in diameter and were sintered at 1400°C for 4 hours. The compound was analyzed by X–ray diffraction. Static immersion and wettability tests were performed to evaluate corrosion resistance in contact with Al–Si. Corrosion tests were carried out by immersion at 800, 900, and 1000°C for 24, 50, and 100 hours, while wettability was carried out at 900, 1000, and 1100°C for 2 hours. Subsequently, the samples were prepared metallographically. Samples were analyzed by optical microscopy, scanning electron microscopy, and image analysis. In general, reaction products consisting of alumina, spinel, oxides, and sulfates were found. The contact angles obtained were 124° to 135°. It is concluded that ceramic substrate Sr4Al6O12SO4 is resistant to corrosion by Al–Si alloy, since the slight thickness of the reaction products found in the samples (100μm) considering the severe conditions of the experiment: 1000°C and 100 hours of isothermal temperature. Furthermore, it can be said that Sr4Al6O12SO4 is not wettable by Al–Si alloys.

This work aimed to carry out a bioremediation study to evaluate the resistance of Penicillium sp. isolated from kefir grains for the treatment of copper. The fungal culture medium was prepared using a 2% malt-agar medium at pH 7.0 in which Penicillium sp. was inoculated. Penicillium sp. growing in a liquid medium showed a decrease in biomass in presence of Cu(NO3)2 (800 mg.L-1), suggesting that the metal impacts the growth rate of the fungus. Moreover, the combined factors of pH and the presence of the inorganic contaminant impacted the radial growth of the fungus, causing inhibition of 73% at pH 4.0, 75% at pH 7.0, and 77% at pH 9.0 in liquid medium compared to control. However, images obtained with scanning electron microscopy showed the integrity of the fungus cell, even at high doses of copper in the medium. Therefore, it can be concluded that Penicillium sp. isolated from kefir grain can bioremediate the environment and that the harmful effects of heavy metals can be minimized as a result biosorption. Although the growth of Penicillium sp. is inhibited, such retardation requires high doses of copper nitrate, thus ensuring the use of this microorganism for protection against the harmful effects of non-essential copper in the environment.

Four decades of proteasome research have yielded extensive information on ubiquitin-dependent proteolysis. The archetype of proteasomes is a 20S barrel-shaped complex that does not rely on ubiquitin as a degradation signal but can degrade substrates with a considerable unstructured stretch. Since roughly half of all proteasomes in most eukaryotic cells are free 20S complexes, ubiquitin-independent protein degradation may coexist with ubiquitin-dependent degradation by the highly regulated 26S proteasome. This article reviews recent advances in our understanding of the biochemical and structural features that underlie the proteolytic mechanism of 20S proteasomes. The two outer α-rings of 20S proteasomes provide a number of potential docking sites for loosely folded polypeptides. The binding of a substrate can induce asymmetric conformational changes, trigger gate opening, and initiate its own degradation through a protease-driven translocation mechanism. Consequently, the substrate translocates through two additional narrow apertures augmented by the β-catalytic active sites. The overall pulling force through the two annuli results in a protease-like unfolding of the substrate and subsequent proteolysis in the catalytic chamber. Although both proteasomes contain identical β-catalytic active sites, the differential translocation mechanisms yield distinct peptide products. Non-overlapping substrate repertoires and product outcomes rationalize cohabitation of both proteasome complexes in cells.

Substrate integrated waveguides reduce the losses and increase the quality factor of resonators in communication filters when compared with traditional planar technologies, while maintaining their low cost and low profile characteristics. Empty substrate integrated waveguides go one step further, removing the dielectric of the substrate. One of these transmission lines is the empty substrate integrated coaxial line (ESICL), which adds the advantage of being a two conductor structure. Thus, it propagates a TEM mode, which reduces the dispersion and the bandwith limitation of other one conductor empty substrate integrated waveguides. Continuous profile filters, at the cost of being long structures, are very easy to manufacture and design (usually no optimization is needed), and they are highly insensitive to manufacturing tolerances. In this work a simple continuous profile filter, with a stop band response, is designed for the first time in the novel ESICL technology. The influence of the design parameters on the insertion losses and fractional bandwidth is discussed. A prototype has been successfully manufactured and measured. A sensitivity analysis shows the high tolerance of the proposed stop band filter to manufacturing errors.

Prompt removal of misfolded membrane proteins and misassembled membrane protein complexes is essential for membrane homeostasis. However, the elimination of these toxic proteins from the hydrophobic membrane environment has high energetic barriers. Transmembrane FtsH is the only known ATP-dependent protease responsible for this task, unlike other well-studied soluble ATP-dependent proteases. The mechanisms by which FtsH recognizes, unfolds, translocates, and proteolyzes its substrates remain unclear. Here, we report the crystal structures of the Thermotoga maritima FtsH periplasmic domain (PD) in an associative trimeric state at a 1.5-1.95 Å resolution. We also describe the pH-dependent oligomerization states of the isolated PD using dynamic light scattering. These observations help us understand how FtsH recognizes membrane-anchored misfolded proteins.

Even though Alzheimer’s disease (AD) is of significant interest to the scientific community, its pathogenesis is very complicated and not well-understood. A great deal of progress has been made in AD research recently and with the advent of these new insights more therapeutic benefits may be identified that could help patients around the world. Much of the research in AD thus far has been very neuron-oriented; however, recent studies suggest that glial cells, i.e., microglia, astrocytes, oligodendrocytes, and oligodendrocyte progenitor cells (NG2 glia), are linked to the pathogenesis of AD and may offer several potential therapeutic targets against AD. In addition to a number of other functions, glial cells are responsible for maintaining homeostasis (i.e., concentration of ions, neurotransmitters, etc.) within the central nervous system (CNS) and are crucial to the structural integrity of neurons. This review explores the: (i) role of glial cells in AD pathogenesis; (ii) complex functionalities of the components involved; and (iii) potential therapeutic targets that could eventually lead to a better quality of life for AD patients

Pairs of potential and flow variables have long been established for interfacing object-oriented component models of physical systems. Recently, however, the use of triplets has been discovered for the purpose of robust modeling. New and powerful Modelica libraries have been developed such as the DLR ThermoFluid Stream library or the introduction of the Dialectic Mechanics library. Their use of triplets is entangled with a special modeling approach that uses Linear Implicit Equilibrium Dynamics. In this paper, we study the basic motivation of this approach, its benefits and drawbacks before we finally demonstrate how it beneficially impacts the generation of corresponding simulation code.

Modern cryptographic protocols such as zero-knowledge proofs and secure multi-party computation have increased the demand for a novel category of symmetric primitives. These primitives are not optimized for traditional platforms such as servers, microcontrollers, and desktop computers but rather for their ability to be implemented in arithmetic circuits. To enable efficient arithmetic operations, they define operations over larger finite fields and use low-degree invertible functions to construct their non-linear layers. Grendel is an arithmetization-oriented permutation that leverages the Legendre Symbol to enhance the growth of algebraic degrees in its non-linear layer. In this paper, we present a preimage attack on the sponge hash function instantiated with the full rounds of the Grendel permutation using algebraic methods. We introduce a technique that allows us to eliminate two full rounds of substitution permutation networks (SPN) in the sponge hash function with minimal or no additional cost. This method can be combined with univariate root-finding techniques and Gröbner basis attacks to break the number of rounds claimed by the designers. By utilizing this strategy, our attack achieves an improvement of two additional rounds compared to the previous state-of-the-art attack. While not breaking its security margin, it allows us to further understand the design and analysis of such cryptographic primitives.

Fluorine represents a privileged building block in pharmaceutical chemistry. Diethylaminosulfur-trifluoride (DAST) is a reagent commonly used for replacement of alcoholic hydroxyl groups with fluorine and is also known to catalyze water elimination and cyclic Beckmann-rearrangement type reactions. In this work we aimed to use DAST for diversity-oriented semisynthetic transformation of natural products bearing multiple hydroxyl groups to prepare new bioactive compounds. Four ecdysteroids, including a new constituent of Cyanotis arachnoidea, were selected as starting materials for DAST-catalyzed transformations. The newly prepared compounds represented combinations of various structural changes DAST was known to catalyze, and a unique cyclopropane ring closure that was found for the first time. Several compounds demonstrated in vitro antitumor properties. A new 17-N-acetylecdysteroid (13) exerted potent antiproliferative activity and no cytotoxicity on drug susceptible and multi-drug resistant mouse T-cell lymphoma cells. Further, compound 13 acted in significant synergism with doxorubicin without detectable direct ABCB1 inhibition. Our results demonstrate that DAST is a versatile tool for diversity-oriented synthesis to expand chemical space towards new bioactive compounds.

Surface-enhanced Raman spectroscopy (SERS) is commonly used for super-selective analysis through nanostructured silver layers in the environment, food quality, biomedicine, and materials science. To fabricate a high-sensitivity but more accessible device of SERS, dc magnetron sputtering technology was used to realize high sensitivity, low cost, stable deposition rate, and rapid mass production. This study investigated various thicknesses of a silver film ranging from 3.0 to 12.1 nm by field-emission-scanning-electron microscope, X-ray diffraction, and X-ray photoelectron spectroscopy. In the rhodamine 6G (R6G) testing irradiated by a He-Ne laser beam, the analytical enhancement factor (AEF) of 9.35x108, the limit of detection (LOD) of 10-8 M, and the relative standard deviation (RSD) of 1.61% were better than other SERS substrates fabricated by the same dc sputtering process because the results show that the 6 nm thickness silver layer has the highest sensitivity, stability, and lifetime. The paraquat and acetylcholine analytes were further investigated and high sensitivity was also achievable. The proposed SERS samples were evaluated and stored in a low humidity environment for up to forty weeks, and no spectrum attenuation could be detected. Soon, the proposed technology to fabricate high sensitivity, repeatability, and robust SERS substrate will be an optimized process technology in multiple applications.

Heavy metal contamination of drinking water is a public health concern that requires the development of more efficient bioremediation techniques. Absorption technologies, including biosorption, provide opportunities for improvements to increase the diversity of metal ions removed and overall binding capacity. Microorganisms are a key component in wastewater treatment plants and they naturally bind metal ions through surface macromolecules but with limited capacity. The long-term goal of this work is to engineer capsule polymerases to synthesize molecules with novel functionalities. In previously published work, we showed that the Neisseria meningitidis serogroup W (NmW) galactose-sialic acid (Gal—NeuNAc) heteropolysaccharide binds lead effectively, thereby demonstrating the potential for using this capsular polysaccharide in environmental decontamination applications. In this study, computational analysis of the NmW capsule polymerase galactosyltransferase (GT) domain was used to gain insight into how the enzyme could be modified to enable the synthesis N-acetylgalactosamine-sialic acid (GalNAc—NeuNAc) heteropolysaccharide. Various computational approaches, including molecular modeling with I-TASSER and molecular dynamics simulations (MD) with NAMD, were utilized to identify key amino acid residues in the substrate binding pocket of the GT domain that may be key to conferring UDP-GalNAc specificity. Through these combined strategies and using BshA, a UDP-GlcNAc transferase, as a structural template, several NmW active site residues were identified as mutational targets to accommodate the proposed N-acetyl group in UDP-GalNAc. Thus, a rational approach for potentially conferring new properties to bacterial capsular polysaccharides is demonstrated.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

High production cost is one of the major factors that limit the market growth of polyhydroxyalkanoates (PHAs) as a biopolymer. Improving PHA synthesis performance and utilizing low grade feedstock are two logical strategies for reducing the cost. As an oleaginous yeast, Y. lipolytica has a high carbon flux through acetyl-CoA (main PHB precursor) which makes it a desired cell factory for PHB biosynthesis. Two different metabolic pathways introduced into Y. lipolytica PO1f in this study for enhancing PHB biosynthesis, along with glucose and acetate as co-substrates. Results showed that NBC pathway led to more than 11% PHB accumulation, while there was non-detectable PHB accumulations using ABC pathway. Further modifications were done using peroxisomal compartmentalization and gene-dose overexpression. Final strain showed up to 41% PHB of CDW with a growth rate of 0.227 h-1. Low growth rate was observed using acetate or glucose as sole carbon and energy source. The co-substrate strategy showed compensatory effect on overcoming inhibitory and toxic effects of both substrates at high concentrations. Cultivating the engineered strain in optimal co-substrate condition predicted by RSM led to 83.4 g/L biomass concentration and 31.7 g/L PHB.

Metallic masters can be used as a metallic mold to replicate polymeric pieces with high resolution. Metallic masters with high resolution were created by photolithography technique and nickel electrodeposition technique. AZ 9260 photoresists and SPR 220-7.0 photoresists were used to coat metallic substrates and to compare results. Steel substrate and nickel substrate were used as the metallic substrate to compare results. Two different nickel electrodeposition protocols were used to compare results. In the conclusion section, was determined the best photoresist, metallic substrate, and nickel electrodeposition protocol to fabricate metallic masters.

Cashew (Anacardium occidentale) processing generates a by-product (CB) with potential for health benefits and could be a favorable ingredient to be added to a probiotic food matrix. This study aimed to assess the functional attributes of CB in fermented milk with a probiotic and a starter culture using in vitro- gastrointestinal conditions. Using a standardized fermentability assay, two strains more adapted to the dehydrated CB were chosen and applied in: Test Formulation (TF, with CB) and Control Formulation (CF, without CB). TF and CF were fermented by the probiotic strain Lacticaseibacillus paracasei subsp. paracasei F19® and the starter Streptococcus thermophilus ST-M6®. During a 28-day refrigerated (6-8 °C) shelf-life study, both strains used in CF and TF were resistant and maintained a population above 8.0 log CFU/mL in the fermented milk. TF had significant increase in total phenolic compounds and greater antioxidant potential during shelf life, along with improved survival of F19® after in vitro-simulated gastrointestinal conditions. The cashew by-product revealed to be promising as a substrate for the strains studied and the presence of CB increased the content of phenolics and antioxidant activity during storage, as well as the gastric resistance to the probiotic., leading to a promising healthy product.

In this study, Ni50Ti50 powder was coated on the surface of graphite substrate (C) by plasma spraying process using a radio frequency inductively coupled plasma reactor. The coating was carried out by using 12- and 9-kW power under Ar atmosphere. The cross-section of coating layers and the surface were examined with SEM, EDX, XRD analysis and microhardness test. The thickness and quality of the coating increased with input power. Many pores were detected in the cross-sectional surface areas. Higher input power caused a better coating layer in NiTi alloy. The hardness of the coating layer decreases with higher input power.

Bio-surfactants are surface-active molecules which are produced by the wide range of microbes including bacteria, fungi, and yeast. This study was conducted to identify bio-surfactants by Bacillus subtilis combined with use of cheap substrates and industrial wastes (Mustard cake, Whey and Soya cake) which are found locally in Nepal. Bacillus subtilis, one of the most potential bio-surfactants producer; was isolated from soil sample of hydrocarbon contaminated site. Isolates were grown in a Minimal Salt Media (MSM) with 10% (v/v) mustard oil cake, whey and soya cake separately. The presence and potential of surfactant was determined by the oil spreading technique, emulsification index (%E24) and surface tension measurement. It was revealed that the surface tensions of cell free extract were 54.41, 60.02 and 56.64 mN/m for from mustard cake, whey and soya cake respectively as compared to distilled water (72.09) at 25oC. The emulsification index values are was found to be highest in engine oil from the bio-surfactant extracted from mustard cake, soya cake and whey respectively. Similarly, mustard oil showed the lowest value of emulsification index. The highest emulsification activity was shown in mustard oil i.e. 1.13 from the cell free extract from mustard oil and lowest in engine oil i.e., 0.07, by the extract from soya cake medium, when measured in spectrophotometer at 540 nm. In conclusion, strain of Bacillus subtilis was found to be the potential surface active agent producers on the mustard oil cake, which can be useful medium for various environmental, food and industrial processes.

Various peptides or non-structural amino acids are recognized by their specific target proteins and perform biological role in various pathways in vivo. Understanding the interactions between target protein and peptides (or non-structural amino acids) provides key information on the molecular interactions, which can be potentially translated to the development of novel drugs. However, it is experimentally challenging to determine the crystal structure of protein-peptide complexes. To obtain structural information on substrate recognition of peptide-recognizing enzyme, X-ray crystallographic studies were performed using triglycine (Gly-Gly-Gly) as main-chain of peptide. The crystal structure of Parengyodontium album Proteinase K in complex with triglcyine was determined at 1.4 Å resolution. Two different bound conformations of triglycine were observed at the substrate recognition site. The triglycine backbone forms stable interactions with β5-α4 and α5-β6 loops of main-chain. One of the triglycine-binding conformations was identical with the binding mode of a peptide-based inhibitor from a previously reported crystal structure of Proteinase K. Triglycine has potential application X-ray crystallography to identify substrate recognition sites in peptide binding enzymes.

Some contaminants of emerging concern (CECs) are known to survive conventional wastewater treatment plants, which introduce them back to the environment and can potentially cycle up in drinking water supplies. This is especially concerning because of the inherent ability of some CECs to induce physiological effects in humans at very low doses. Advanced oxidation processes (AOPs) such as TiO2 based photocatalysis are of prominent interest for addressing CECs in aqueous environments. Natural water resources often contain dissolved metal cations concentrations in excess of targeted CEC concentrations. These cations may significantly, adversely impact degradation of CECs by scavenging TiO2 surface generated electrons. Consequently, simple pseudo first order or Langmuir-Hinshelwood kinetics are not sufficient for reactor design and process analysis in some scenarios. Rhodamine B dye and dissolved copper cations were studied as reaction surrogates to demonstrate that TiO₂ catalyzed degradation for very dilute solutions is very nearly completely due to homogeneous reaction with hydroxyl radicals and that in this scenario the hole trapping pathway has negligible impact. Chemical reaction kinetic studies were then carried out to develop a robust model for RB/metal reactions that is exact in the electron pathways for hydroxyl radical production and metal scavenging.

Biomass as a whole offers a more diverse potential for valorisation than any other renew-able energy source. As one of the stages in the separation of bio-oil involves the liquid mixture of acetol and acetic acid, and as both components are particularly well suited for valorisation, a hybrid method has been developed for their separation with a high purity level through an approach combining liquid-liquid extraction and rectification. In order to design and simulate the flowsheet, the ChemCAD 7.0 simulation software has been used. Sensitive analyses have been carried out to investigate the influence of the different pa-rameters in the rectification columns such as the reflux ratio, the feed stage location, and the vapour/bottom molar flow ratio. The effect of different extractants and of their excess on the separation process as well as the possibility of regenerating the extractant has also been studied. Tri-n-octylamine has accordingly been selected as a separating agent which has been fully recycled. The end result for separating an initial 48/52 wt% ace-tol/acetic-acid liquid mixture has been acetol with a purity of 99.4 wt% and acetic acid with a purity of 100 wt%.

The use of active methodologies in the university is a priority to achieve higher quality learning. One of these methodologies with the greatest potential for training in competencies is Project-Oriented Learning (PLA), using it in an innovative way. Associating the use of this methodology with the objectives of sustainable development, which have become even more important since the Pandemic by COVID-19, can be a good idea to achieve a more sustained and situated learning. The aim of this study is to find out to what extent research on teaching innovation with Project-Oriented Learning is associated with the Sustainable Development Goals. A systematic review was carried out as indicated by PRISMA through the following databases: WOS and Scopus. WOS found 15 articles on AoP and 6 on Project-Oriented Learning and sustainability. In Scopus 2 were found in 2019. The main results show that in the University, especially in the branches of engineering, AoP is widely used, however, it is rarely related to SDGs. Among the conclusions, we highlight the need for research on project-oriented learning and sustainable development goals.

The adaptation stress experienced by overseas dispatched employees has serious implications for their physical and mental health and work performance. This study aimed to investigate the impact of resource-oriented music listening on work stress among overseas dispatched employees. The study recruited 10 participants of different ages and occupations who had worked abroad for at least 3 years. Five sessions of personalized resource-oriented music listening, and interviews were conducted. The Global Assessment of Recent Stress Scale (GARS) and Job Stress Scale (JSS) were used to measure stress before and after the intervention. Results showed that participants' work stress and perceived stress were significantly reduced after the music therapy intervention. The study also found that 'awareness' and 'self-acceptance' were factors that reduced regulatory stress among overseas dispatched employees. This study highlights the potential of resource-oriented music listening as a useful tool to address workplace stress and promote the well-being of expatriate employees.

The performance of lattice-Boltzmann solver implementations usually depends mainly on memory access patterns. Achieving high performance requires then complex code which handles careful data placement and ordering of memory transactions. In this work, we analyse the performance of an implementation based on a new approach called the data-oriented language, which allows the combining of complex memory access patterns with simple source code. As a use case, we present and provide the source code of a solver for D2Q9 lattice and show its performance on GTX Titan Xp GPU for dense and sparse geometries up to 4096 2 nodes. The obtained results are promising, around 1000 lines of code allowed us to achieve performance in the range of 0.6 to 0.7 of maximum theoretical memory bandwidth (over 2.5 and 5.0 GLUPS for double and single precision, respectively) for meshes of size above 1024 2 nodes, which is close to the current state-of-the-art. However, we also observed relatively high and sometimes difficult to predict overheads, especially for sparse data structures. The additional issue was also a rather long compilation, which extended the time of short simulations, and a lack of access to low-level optimisation mechanisms.

The paper interprets a comparison of two mostly used techniques of a field-oriented control for 6-phase electric drives, with their pros and cons, as well as their differences in construction and behaviour. Both of these approaches have been realized. Frequency and step responses analysis have been demonstrated with a 6-phase permanent magnet synchronous machine. Experimental results have been compared with simulations based on a mathematical model.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

Two-dimensional (2D) semiconductors like Transitional Metal Dichalcogenides (TMDCs) have attracted strong research interest in the last decade. Unlike the more celebrated 2D material graphene, TMDCs like molybdenum disulfide(MoS₂) possess bandgap. The number of layers critically depends on the band structure of MoS₂. For example, it is indirect for bulk MoS₂. However, it becomes direct bandgap material for a monolayer MoS₂. Monolayer MoS₂, therefore, becomes an important material for photoelectronic devices. An essential aspect of such devices is the metal-semiconductor junction. Metal-TMDC junction is, therefore, a well-studied interface due to its importance for 2D materials-based photoelectronic devices. Most importantly, it can be flexible, stretchable to it’s length, and bent to a large angle. We used metals like Au and Al to interface with TMDs like MoS₂. We used silicon and PDMS as substrates. So, we have to focus on investigating the relative properties of various TMDCs. We see change in band energy and vibrational modes via Photoluminiscence and Raman spectroscopy as shown in the article. However, certain aspects are yet to be explored, for example, how this interface behaves in the presence of strain.

Cells are influenced by several biomechanical aspects of their microenvironment, such as substrate geometry. According to the literature, substrate geometry influences the behavior of muscle cells; in particular, the curvature feature improves cell proliferation. However, the effect of the substrate geometry on the myogenic differentiation process is not clear and needs to be further investigated. Here, we show that the 3D co-printing technique allows the realization of substrates. To test the influence of the co-printing technique on cellular behavior we realized linear polycaprolactone substrates with channels in which a fibrinogen-based hydrogel loaded with C2C12 cells was deposited. Cell viability and differentiation were investigated up to 21 days in culture. The results suggest that this technology significantly improves the differentiation at 14 days. Therefore, we investigate the substrate geometry influence by comparing three different co-printed geometries – linear, circular, and hybrid structures (linear and circular features combined). Based on our results, all structures exhibit optimal cell viability (> 94%) but the linear pattern allows to increase the in-vitro cell differentiation, in particular after 14 days of culture. This study proposes an endorsed approach for creating artificial muscles for future skeletal muscle tissue engineering applications.

Gene electrotransfer is one of the main non-viral methods for intracellular delivery of plasmid DNA, wherein pulsed electric fields are used to transiently permeabilize the cell membrane allowing enhanced transmembrane transport. By localizing the electric field over small portions of the cell membrane using nanostructured substrates, it is possible to increase considerably the gene electrotransfer efficiency while preserving cell viability. In this study, we design an electrotransfer approach based on commercially available cell culture inserts with polyethylene-terephthalate (PET) porous substrate. We first use multiscale numerical modelling to determine the pulse parameters, substrate pore size, and other factors that are expected to result in successful gene electrotransfer. Based on numerical results we design a simple device combining an insert with substrates containing pores with 0.4 um and 1.0 um diameter, a multiwell plate, and a pair of wire electrodes. We test the device in three mammalian cell lines and obtain transfection efficiencies similar to those achieved with bulk electroporation, but with low-voltage pulses that do not require the use of expensive electroporators. Our combined theoretical and experimental analysis calls for further systematic studies that will investigate the influence of substrate pore size and porosity on gene electrotransfer efficiency and cell viability.

Metal powder bed fusion (PBF) additive manufacturing (AM) builds metal parts layer by layer upon a substrate material. The strength of this interface between substrate and printed material is important to characterize, especially in applications where the substrate is retained and included in the finished part. This paper studied the tensile and torsional strengths of wrought and additively manufactured (through PBF) SS316L and compared them to specimens composed of half wrought material and half PBF material. The PBF specimens consistently exhibited higher strength and lower ductility than the wrought specimens. The hybrid PBF/wrought specimens performed similarly to the wrought material. In no specimens did any failure appear to occur at or near the interface between wrought substrate and PBF material. In addition, most of the deformation in the PBF/wrought specimens appeared to be limited to the wrought portion of the specimens. These results are consistent with microscopy showing smaller grain size in the PBF material, which often leads to increased strength in SS316L due to the Hall-Petch relationship.

Metal-supported fuel cells (MSCs) offer potential material cost and robustness advantage over anode supported cells (ASCs). Because of the very good thermal shock stability of such MSCs, these can be heated up very quickly. However the challenge co-firing of metal substrate and electrolyte stays still unsolved. The production of the core component, the tape casted metal substrate, with defined shrinkage resulting from modification of metal powders is presented in the paper. This approach leads to an adjustment of the shrinkage mismatch during sintering, between metal and ceramic components, and adjustment of target specifications like porosity, green density and layer thickness.

The development of printing technologies has enabled the realization of electric circuit fabrication on flexible substrate. However, the current technique remains restricted to single-layer patterning. In this paper, we demonstrate a fully solution-processable patterning approach for multi-layer circuits using a combined method of laser sintering and ablation. Selective laser sintering of silver (Ag) nanoparticle-based ink is applied to make conductive patterns on a heat-sensitive substrate and insulating layer. The laser beam path and irradiation fluence are controlled to create circuit patterns for flexible electronics. Microvia drilling using femtosecond laser through the polyvinylphenol-film insulating layer by laser ablation, as well as sequential coating of Ag ink and laser sintering, achieves an interlayer interconnection between multi-layer circuits. The dimension of microvia is determined by a sophisticated adjustment of laser focal position and intensity. Based on these methods, the flexible electronic circuit with chip-size-package light-emitting diodes was successfully fabricated and demonstrated with functional operations.

The aim of this paper is to develop a composite coating on St 304 steel employing TIG process. Ti wire cored with graphite powder is used as the means of coating material. The process parameters are varied in order to develop coating with optimum characteristics (i.e., hardness and wear resistance). The microstructure of the coating is analyzed with SEM and XRD. It is found that both of the hardness and wear resistance increase as the current increases while both of these properties decrease as the travelling speed increases. It is found that the coated samples with composite layers have more hardness than the substrate and it could range up to 1100 HV being almost 4.5 times higher than the hardness of St 304. Likewise, the wear resistance of coating is observed to be 4.5 times higher than that of substrate. The high performance of coating, as revealed by microstructural analysis, is due to formation of TiC and Cr₂₃C₆ .The optimum conditions to produce the coating are proposed to be 120 A current and 3.17 mm/s travel speed.

Proton exchange membrane (PEM) fuel cells have emerged as a viable alternative energy production source for stationary and transportation applications. Reliable and sustainable fuel cell operation requires effective water management. Membrane water content can vary along the stack during transients which can lead to losses in fuel cell performance. To control these variations a model that predicts the internal humidity dynamics of the stack is needed. In this study, a control-oriented model for predicting membrane water content variation was developed and implemented in MATLAB/Simulink. A lumped parameter model was initially developed and then further discretized into smaller control volumes to track humidity distribution along the stack. To validate the model’s predictions, the predicted results were compared to computer simulation results from GT-Suite. The root mean square error (RMSE) between the model’s prediction and GT-Suite’s simulation results was found to be within 1.5 membrane water content for all cases, demonstrating the model’s capability to capture the variation of membrane water content along the stack. The developed model will be useful for real-time control of membrane water content variation in PEM fuel cells.

[Background] Previous research achievements of the service-oriented tourist city network have often focused on the analysis of its geographical distribution and service role of the important cities instead of the connections and hierarchical tendencies between the whole city in a large region.[Method]Using big data approaches on the regional connections of 38 tourism organizations including famous hotels, air passenger transport, tourism service agencies across 63 most important tourist cities in China. Fuzzy c-means clustering analysis is used to define 8 city arena clusters. [Results]According to the distributions of connectivity between 63 cities, these eight clusters play different service functional roles in the urban tourism network at four hierarchies. With their “center-edge” memberships, these arena clusters are formed by the interweaving process of regional and hierarchical tourism service connections. The results include the analysis of the various service-oriented tourist city in China and point out the geography “gap” faced by network. [Conclusion] Service-oriented tourist cities need to find their hierarchies and positioning in the network scientifically to avoid blind development, to make regional urban tourism sustainable development.

Coronavirus, also known as COVID-19, has been declared a pandemic by the World Health Organization (WHO). At the time of conducting this study, it had recorded over 1.6 million cases while more than 105,000 have died due to it, with these figures rising on a daily basis across the globe. The burden of this highly contagious respiratory disease is that it presents itself in both symptomatic and asymptomatic patterns in those already infected, thereby leading to an exponential rise in the number of contractions of the disease and fatalities. It is therefore crucial to expedite the process of early detection and diagnosis of the disease across the world. The case-based reasoning (CBR) model is an effective paradigm that allows for the utilization of cases’ specific knowledge previously experienced, concrete problem situations or specific patient cases for solving new cases. This study therefore aims to leverage the very rich database of cases of COVID-19 to solve new cases. The approach adopted in this study employs the use of an improved CBR model for state-of-the-art reasoning task in classification of suspected cases of Covid19. The CBR model leverages on a novel feature selection and semantic-based mathematical model proposed in this study for case similarity computation. An initial population of the archive was achieved with 68 cases obtained from the Italian Society of Medical and Interventional Radiology (SIRM) repository. Results obtained revealed that the proposed approach in this study successfully classified suspected cases into their categories at an accuracy of 97.10%. The study found that the proposed model can support physicians to easily diagnose suspected cases of Covid19 base on their medical records without subjecting the specimen to laboratory test. As a result, there will be a global minimization of contagion rate occasioned by slow testing and as well reduce false positive rates of diagnosed cases as observed in some parts of the globe.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

Abstract: The aim of this study was to evaluate the effects of solids accumulation on greenhouse gas (GHG) emissions, substrate, plant growth and performance of a horizontal flow (HF) treatment wetland (TW) planted with Phragmites australis (Cav.) Trin. ex Steud. sub sp. australis. The study was carried out in an eight-year-old full-scale HF-TW located in the Mediterranean region (Sicily, Italy). To collect data inside the HF unit, nine observation points (besides the inlet and the outlet) along three 8.5 m long transects (T1, T2, and T3) were identified. The first transect (close to the inlet zone) showed hydraulic conductivity (Ks) reduction of about one order of magnitude higher than the other two. Results highlighted GHG emissions increasing during the summer when temperature and solar radiation were higher than in the rest of the year. Carbon dioxide (CO2) emis-sions decreased from T1 to T3, with maximum monthly values in T1 (21.4 g CO2 m-2 d-1) about double with respect to T2 (12.6 g CO2 m-2 d-1) and T3 (10.7 g CO2 m-2 d-1) observed in July. The CO2 seasonal trend was similar to that of P. Australis growth. Theoretical me-thane (CH4) emissions followed the trend of volatile solids (VS), which was about 3.5 and 4 times in T1 to T2 and T3. The highest CH4 emissions in T1 were probably due to anaerobic bacteria (methanogens) that proliferated in the waterlogged, anoxic part of TW. The pore-clogging affected the chemical oxygen demand (COD) removal efficiency which de-creasing from T1 to T3 for the observation period. Notwithstanding this behaviour, the final effluent quality was very satisfactory with the average value of COD removal efficiency above 90%.

Detecting rotated objects in remote sensing images poses a substantial challenge. These images usually cover a wide field of view, containing diverse and complex backgrounds with variously sized ground objects densely distributed. Therefore, identifying objects of interest in remote-sensing images is challenging. While integrating Convolutional Neural Networks (CNNs) and Transformer networks has exhibited progress in detecting rotated objects, there is still scope for enhancing feature extraction and fusion. To address this issue, we propose a feature extraction module, a feature context aggregation module, and a multi-scale feature fusion module. Initially, we substitute the Spatial Pyramid Pooling Bottleneck (SPPFBottleneck) with a new module aimed at extracting multi-scale features, thereby enhancing the detection of small objects in complex backgrounds. Next, we develop a novel module for the multi-scale fusion of contextual information within feature maps, extracting valuable information. Finally, we combine the original features with the fused ones to prevent the loss of specific features in the fusion process. We refer to our newly proposed model as the "Multi-scale Feature Context Aggregation Network" (MFCANet). We assess our approach on three challenging remote sensing datasets: MAR20, SRSDD, and HRSC. Comprehensive experimental results show that our method surpasses baseline models by 2.13%, 10.28%, and 1.46% mAP on the MAR20, SRSDD, and HRSC datasets, respectively.

It is well known that the basis of diffraction analysis of matter is scattering, including scattering of ultrashort laser pulses. In the theory of scattering of ultrashort pulses the pulse duration parameter is usually not taken into account, which leads to some error. This error may be more significant than the considered effects in the scattering of the pulse on the studied structure. In this paper it is shown that the pulse duration parameter should be taken into account when scattering X-ray pulses on oriented diamonds with NV-centers. It is shown that the scattering spectra can be used to judge the orientation of NV centers in the diamond structure. The obtained results may be very different from the widely used theory of diffraction analysis, which confirms the necessity of taking into account the pulse duration parameter in the diagnosis of complex structures.

Detecting rotational objects in remote sensing imagery is a significant challenge. These images typically encompass a broad field of view, featuring diverse and intricate backgrounds, with ground objects of various sizes densely scattered. As a result, identifying objects of interest within these images is a daunting task. While the integration of Convolutional Neural Networks (CNN) and Transformer networks leads to some advancements in rotational object detection, there is still room for improvement, particularly in enhancing the extraction and utilization of information related to smaller objects. To address this, our paper presents a multi-scale feature fusion module and a global feature context aggregation module. Initially, we fuse original, shallow, and deep features to reduce the loss of shallow feature information, thereby improving the detection performance of small objects in complex backgrounds. Subsequently, we compute the correlation of contextual information within feature maps to extract valuable insights. We name the newly proposed model the "Multiscale Feature Context Aggregation Module" (MFCA). We evaluate our proposed methodology on three challenging remote sensing datasets: DIOR-R, HRSC, and MAR20. Comprehensive experimental results show that our approach surpasses baseline models by 2.07\% mAP, 1.02\% mAP, and 1.98\% mAP on the DIOR-R, HRSC2016, and MAR20 datasets, respectively.

Thin-wall heat pipe is an efficient heat transfer component, which has been widely used in the field of heat dissipation of high-power electronic equipment in recent years. In this study, the orange peel morphology defect of thin-wall heat pipes after bending deformation was analyzed both for the macro 3D profile and for the micro-formation mechanism. The results show that after high temperature sintering treatment, the matrix grains of heat pipe are coarsened seriously and formed a strong Goss texture, while a certain annealing twins with the unique Copper orientation are retained. The distribution of Schmid factor value subjected to the uniaxial stress indicate the inhomogeneity of intergranular deformation exist among the annealing twins and matrix grains. The annealing twin exhibit a “hard-oriented” component during the deformation; thus, it plays a role as barrier and hinder the slipping of dislocation. As the strain accumulates, part of the annealing twins may protrude from the surface of heat pipe, forming a large-scale fluctuation of the surface as the so called the “orange peel” morphology. The 3D profile shows the bulged twins mostly perpendicular to the drawing direction, with about 200-300μm in width and 10-20μm in height.

Grazing incidence X-Ray Diffraction spectroscopy was employed to characterize crystallinity of Iron, Nickel, Copper and Tungsten, prepared by sparking discharge process in presence of 0.4 T magnetic field at ambient temperature 25 °C. Iron thin film preserved crystallinity even after one year of ageing. Nickel exhibit higher crystallinity when sparked in nitrogen gas flow from the one sparked in oxygen. Tungsten was successfully crystalized after just 40 minutes of sparking inside of magnetic field.

Macadamia nut plantings in China are expanding year by year. In order to further promote the superior varieties, this study analyzed the effects of different varieties of rootstock and scion on the survival rate as well as the effects of 18 different ratios of substrate composition on seedling growth were analyzed. The results showed that: The survival rate of HAES788 varieties as rootstock and Guire No.1 as scion was the highest, reaching 96%. The optimal grafting time in December was better than that in March. Substrate formulations 12, 13, 15 and 16 had agglomerated soil and well-developed root systems compared to the controls. Plant height, stem diameter, leaf length, leaf width, and dry weight of aboveground and underground parts were significantly higher than those of the control. In addition, the substrate formulations 12, 13, 15 and 16 significantly improved the organic matter, total nitrogen, and total potassium content of the substrate soils, but little on total phosphorus content. All in all, macadamia grafting times are best in December, with HAES788 and Guire No.1 being the best rootstock and scion. Substrate formulations 12, 13, 15 and 16 are the optimal formula. This study provides a solid foundation to produce high-quality macadamia seedlings.

In light of the hazardous effects of global warming brought on by climate change, bioethanol production is one of the key alternatives in which the world has expressed a great deal of interest. Two factors—indigenous production and price—are crucial for bioethanol to be appealing in Africa and, for that matter, Ghana. The objective of this research is to produce bioethanol from cheap lignocellulosic materials using onsite enzymes produced from cassava peels degrading fungi. Due to Ghana's prominent position as one of the leading cassava producers in the world, the study focused on utilizing cassava peels, which are underutilized in the country. The research was conducted in multiple stages. In the first stage, the peels were prepared by washing, drying, and manually crushing them using mortar and pestle. The second stage involved analyzing the chemical composition of the peels, including starch and insoluble fibre, which were determined as Acid Detergent Fiber (ADF), Neutral Detergent Fiber (NDF), and Acid Detergent Lignin (ADL). The results showed significant levels of cellulose (39.78%) and starch (31.21%), indicating that cassava peels are valuable raw materials for bioethanol production. The content of hemicellulose (21.11%) and lignin (3.84%) were also determined. In the third stage, using a Petri dish, three fungi (ICPF1, ICPF2, and ICPF3) were isolated from two different cassava peels. ICPF1 was only identified from fresh cassava peels (FCP), while all three fungi were identified from decayed cassava peels (DCP). Morphologically, these fungi were identified as Aspergillus niger, Aspergillus flavus, and Rhizopus stolonifer. The fourth stage focused on optimizing the enzyme activity of the three isolates for potential applications, with A. niger demonstrating the highest enzyme activity with a diameter of zone of clearance of 16 mm. Stage five involved optimizing the production of the onsite enzyme in a 50ml flask using A. niger, basal salt medium (BSM), and cassava peels as a substrate. The DNSA method was used to measure the absorbance of maltose and glucose at 540 nm for various substrate concentrations (1%, 3%, 5%, 8%, and 10%) at specific intervals of 2, 4, 6, 8, and 10 days with a spore concentration of 2.1 x 105 cells/ml. The maltose and glucose concentrations were calculated as 7.138mg/ml and 6.398 mg/ml, respectively, and the corresponding enzyme activity was determined as 4.759U/ml and 4.265U/ml. The optimal conditions of Day 4 and a substrate concentration of 10%, along with a fixed temperature of 30°C and a pH of 5.5, were used to prepare the onsite enzymes in a 500 ml flask for the fermentation process. The onsite enzymes were used for saccharification and Saccharomyces cerevisiae for fermentation under simultaneous saccharification and fermentation (SSF) process. A mixture of 20 ml of onsite enzymes and 1.5 g of S. cerevisiae were added to substrate concentrations of 5%, 10%, and 20%, and the ethanol concentration was analyzed daily for 7 days using Gas Chromatography (GC). The highest ethanol concentration (1.316%) was observed on Day 5 with a substrate concentration of 20%, while the lowest concentration (0.123%) was recorded on Day 1 with a substrate concentration of 5%.

Metal plasmonic nanostructures have promising applications in biosensing due to their ability to facilitate light-matter interaction. However, the damping of the metal leads to a wide full width at half maximum (FWHM) spectrum and results which restricts its sensing capabilities. In this research, we present a novel non-full-metal nanostructure, namely indium-tin oxide (ITO)-Au nanodisk arrays consisting of top ITO nanodisk arrays and a bottom gold layer, and compare the coupling mode with the full-metal nanodisk arrays. The FWHM of proposed ITO-Au nanodisk array reduces to one fifth of that all metal nanodisk arrays, which is generated mode-coupling by surface plasmon modes at metal interfaces with magnetic resonance mode. Furthermore, the thickness variation of nanodisks has no impact on the sensing performance of this ITO-based nanostructure, ensuring excellent tolerance during preparation. We fabricated both structures by using template transfer and vacuum deposition techniques and calibrated their sensing performances by detect Immunoglobulin G (IgG) protein molecules. Both theoretical and experimental results demonstrate that ITO-Au nanodisk arrays provide an effective solution for biosensing applications.

Rapeseed meal (RM) is an important agroindustrial by-product produced in large quantities by oil extraction from seeds. However, the efficient utilization of RM as animal feed is limited by its low metabolizable energy, poor palatability, and high levels of fiber and anti-nutritional components. Here, we investigate the potential of enriching RM with single-cell protein by fermentation with conventional and unconventional yeasts, to make a nutritionally improved feed component. The process of simultaneous saccharification and fermentation improved the parameters of the waste biomass, especially the protein content, the amount of crude fiber, and the degree of biotransformation of isoflavone compounds present in the waste material. Fermentation yielded the highest protein gain for the Saccharomyces cerevisiae Ethanol Red strain (ΔN=2.38%) at a biomass load of 12.5 g and for Scheffersomyces stipitis (ΔN=2.34%) at an enzyme dose of 0.125ml/10g DM. Crude fiber content (CF) was reduced by 2.55–7.18%. The SSF process resulted in the conversion of isoflavones to forms with fewer adverse effects and lower estrogenic activity.

In this work we explored how solvents can affect olefin oxidation reactions catalyzed by MCM-bpy-Mo catalysts and whether their control can be made with those players. The results of this study evidenced that polar and apolar aprotic solvents modulated the reactions in different ways. Experimental data showed that acetonitrile (aprotic polar) could hinder largely the reaction rate whereas toluene (aprotic apolar) did not. In both cases product selectivity at isoconversion was not affected. Further insights were obtained by means of neutron diffraction experiments, which confirmed the kinetic data allowing to propose a model based on substrate-solvent crosstalk by means of hydrogen bonding. In addition, the model was also validated in the ring-opening reaction (overoxidation) of styrene oxide towards benzaldehyde, which progressed when toluene was the solvent (reaching 31% styrene oxide conversion) but was strongly hindered when acetonitrile was used instead (reaching only 7% conversion), due to the establishment of H-bonds in the latter. Although this model was confirmed and validated for olefin oxidation reactions, it can be envisaged that it may also be applied to other catalytic reaction systems where reaction control is critical, while widening its use.

The experiment was conducted to determine the effects of different substrate on the survival, growth and total number of moulting in juvenile red claw, Cherax quadricarinatus for aquaculture purposes. In the present study, there is a problem in culturing juvenile stage of C. quadricarinatus especially for survival and growth. Thus, a substrate was used to improve the survival and growth of C. quadricarinatus especially for the intensive system due C. quadricarinatus need a large space to survive. C. quadricarinatus with initial body weight from 1.10 to 2.90 g, total length 2.82 to 4.36 cm were placed in tanks (80 L in volume capacity) with 55L in water and there are eight juveniles in each tank. Treatment tanks were introduced with coral as treatment 2 and pipe as treatment 3. While, tank without shelters was set as control (treatment 1). Black nets were installed on top of each for circumventing foreign objects enter the tank and protect from direct sunlight. Besides, C. quadricarinatus were acclimatized for seven days before started the experiment. The experiment was done in duplicate and conducted for 60 days and C. quadricarinatus were fed twice daily (morning and evening) based on 5% of body weight. From the total of two replications, C. quadricarinatus for treatment 2 (coral) were significantly in survival (81.25±8.84%), weight gain (347.36 ±6.04%), specific growth rate (2.50±0.02%), carapace length (32.93 ± 0.93 %) and total number of moulting (55.00±2.93%) compared to other treatments. Besides, the control treatment (treatment 1) has a lower percentage in survival (37.50±8.84%) weight gain (122.60±20.51%) specific growth rate (1.33±0.15%), carapace length (25.84±0.33 %) and total number of molting (29.00±0.71%). As a conclusion, usage of coral as the substrate in the rearing tank showed improvement in survival, weight gain, specific growth rate, carapace length and total number of molting in C. quadricarinatus. The coral can use in rearing tank for increase the growth and survival for a small scale and not for commercial. In addition, in the environmental aspect, the present study showed the benefit of replacing the use of PVC pipes with the natural structure of dead coral.

The surface enhanced fluorescence（SEF）detection bases by plasmonic nanopillars array with nanoparticles has opened up a new gate in the application of biological imaging and sensing. The fluorescence enhancement of the probe molecule depends on its position in equilibrium, which is close to the hot spot leading to the electromagnetic field enhancement, but not too close to the metal surface resulting in quenching. Here, a large scale SiO₂-Ag-cicada wing SEF substrate was fabricated by magnetron sputtering with correction enhancement factor of 797.6. Thereinto the cicada wing provides the skeleton of the nanopillars array structure, the deposited Ag constructs two kinds of hot spots, and SiO₂ forms a separation layer to prevent quenching. Moreover, the substrate exhibited good reproducibility, high sensitivity with low limits of detection (LOD) and high stability for oxidation resistance. We propose that SEF substrate with modification of SiO₂ can not only improve the enhancement performance, but also expanding its application in the biological investigations.

Aeroponics is a relatively new soilless culture technology, which may produce food in space limited cities or non-arable land with high water use efficiency. The shoot and root growth, root characteristics, mineral contents of two lettuce cultivars were measured in aeroponics, as compared with hydroponics and substrate culture. The results showed that aeroponics remarkably improved the root growth with a significant greater root biomass, root/shoot ratio, and several times higher total root length, root area and root volume. However, the greater root growth did not lead to a better shoot growth compared with hydroponics, due to the limited availability of nutrients and water. It can be concluded that aeroponics systems may be better for high value true root crops production. Further research is necessary to figure out the suitable pressure, droplet size, and misting interval in order to improve the continuously availability of nutrients and water in aeroponics, if it is used to grow crops like lettuce for harvesting above-ground parts.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

Whether the universe is a computer simulation, or whether we wish to efficiently model our universe in a computer simulation, there would be benefits to modeling it in a fashion analogous to computer spreadsheet, each lattice cell can be conceived as containing all the mathematical formula necessary to continuously compute its state relative to changes in all its neighboring cells, and by progression, in relation to all the cells of entire space-time lattice. Alternatively, the “real” universe may itself be built on a space cell lattice, an irregular foam of space cells, in which each cell may be conceived as a multidimensional cell of distortable space, the shape of which fully describes (a) the four basic forces (gravity, electromagnetic, strong, weak) observed at that cell of space, and (b) the probability (or weight distribution) of any quantum states overlapping the cell and its neighbors. At an appropriate scale, it would appear that this conceptual model would resolve apparent conflicts between general relativity and quantum physics. It would also provide a new interpretation of Planck’s constant as description of the number of space cell events associated with any set of observable events. If formulae operating at a lattice cell level can be improve our ability to understand and model larger scale phenomena, this would be strong evidence in favor of the theory that mathematics is not just a human invention but rather an inherent feature of space-time itself.

As smoke toxicity is unregulated outside of the mass transport industry, there is no set methodology for assessing smoke toxicity of construction products, like OSB, on a large-scale. This research aims to assess the novel design of a modified ISO 9705 room corner test designed for smoke toxicity quantification. Three tests conditions will be assessed to determine if restriction of ventilation is enough to force a fire to transition to under-ventilated flaming, or if the fuel loading is much more important in affecting the fire severity and fire condition. The research found that fuel loading and test geometry has more significant impact on the fire condition than restricting the ventilation. While imposing restrictions on the test rooms ventilation did increase the equivalence ratio, it was not sufficient enough to force the transition into under-ventilated flaming. The addition of a door to the test room did not force the fire to transition to under-ventilated flaming. When doubling the fuel loading, there was sufficient fuel for the fire to transition to under-ventilated flaming. This research has provided the experimental methodologies to assess smoke toxicity at a range of ventilation conditions on a large-scale.

The primary purpose of this investigation was to identify safety-oriented bicycling practices commonly used by adult riders in an urban setting (Brooklyn, New York), and to explore whether there are any differences between the safety-oriented practices of men and women riders. Methods: 24 adult riders (14 men, 10 women) in Brooklyn were interviewed concerning their perceptions of bicycling hazards and their safety-oriented practices. Interviews were recorded, transcribed, and analyzed through thematic analysis. Fisher’s Exact Test was employed to test for gender differences. Results: Participants identified a variety of hazards, mainly due to motor vehicles but also pedestrians and roadway conditions. The analysis distilled twenty-one bicycling practices to summarize prevalent views of the participants about safe riding practices. Related items were grouped under broader categories, generating seven safety-oriented bicycling strategies. Few differences based on gender were found in the analysis; however, women in this study were more likely than men to say that they felt disrespected by other road users. Conclusion: Seven strategies may be important for safe urban bicycling: minimizing exposure to other road users (especially motor vehicles) while riding, being vigilant and anticipating what others might do, riding in a predictable fashion, making one’s presence known to other road users, making sure it is safe before proceeding, obeying traffic rules, and riding at a safe speed. Future studies could develop these concepts further and test whether they are associated with involvement in traffic crashes.

The present work encompasses an application-oriented perspective to the possible employment of gold nanoparticles as nanomedicine in cancer therapeutics. The rationale of the work lies in the growing needs for assessment of advanced alternative treatment of cancer employing functionalized nanoparticles as nanomedicine. Gold nanoparticles fabricated via green chemistry methods by leaves of a time-honored medicinal plant, Piper betle were ascertained for their synthesis and properties under the umbrella of characterization of nanoparticles, through various techniques like UV-vis spectroscopy, FTIR spectroscopy, X-ray diffraction, and scanning electron microscopy. The cytotoxicity assay of well-characterized gold nanoparticles was monitored against lung cancer cell line (A549) by metabolic and imaging assays. MTT assay or the metabolic assay was performed for a range of nanoparticles’ concentrations. The results were promising and proved to be a leading-edge venture, envisaging the possibility of gold nanoparticles for cancer therapeutics.