Digital-based differential amplifiers (DDA) are particularly suitable to low voltage digital integrated circuit technologies. This paper presents an exhaustive analysis of the digital-based analog amplifiers to take advantage of today's high-performance digital technologies and of computer-aided design (CAD) commonly employed to design integrated circuits. The operating principle and the main mathematical relations of the digital-based differential amplifiers are discussed along with an exhaustive explanation of its operating regions and of the corresponding power consumption. Finally, a detailed description of the design procedure of in UMC 180nm standard CMOS technology is shown.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

Methane is the main cause of sewer explosion accidents, and the available monitoring methods mainly use portable gas sensors for on-site detection. However, these methods cannot grasp the dynamic changes in methane in a sewer in real time or make better predictions of methane explosion accidents. Here, we present a low-power online monitoring system for sewer methane in order to ensure the safety of urban sewers. A low-power ultrasonic gas sensor was used to monitor the methane content in biogas. Due to the impacts of changes in CO2, temperature, and humidity in the sewer on the ultrasonic methane measurement results, a corresponding compensation method was proposed. The effectiveness of the compensation method was verified through experiments, which measured the methane concentration under different influences, and the methane values measured before and after compensation were compared. The power consumption was only 1.28 mW if the system worked in intermittent operation mode, and it could operate for about 1.5 years by selecting a lithium battery with a capacity of 5 A · H. The experimental results showed that the gas detection accuracy could meet the commercial requirements and had a high compensation for the impacts of carbon dioxide, temperature, and humidity.

Computer systems that operate in remote locations such as satellites, remote weather stations and autonomous robots are highly limited in the availability of energy for their operation. This work aims to employ artificial intelligence algorithms in energy management in order to obtain the maximum energy yield and the prediction of energy availability to the system. The work presents the main types of algorithms used in artificial intelligence and presents the creation of a prototype that will operate as a low power system powered by batteries and a small solar plate, the prototype will perform inferences on the LSTM neural network algorithm in order to predict the future availability of energy, consequently the management system will carry out the energy distribution in order to obtain the maximum operation of the prototype without total discharge of the batteries. So that the artificial intelligence system could be embedded in the prototype, the TensorFlow Lite framework was used, which allows the inference to be carried out in devices with low consumption and limited processing power.

Low dropout (LDO) regulators are widely used in portable electronic devices because they 1 occupy small chip and printed circuit board (PCB) areas. This work presents the design of a low 2 noise low dropout (LDO) linear voltage regulator using folded cascode operational amplifier and 3 source follower buffer for frequency compensation. The proposed design achieves low output noise 4 with feedback loops, which makes it possible to improve load and line regulations as well as the 5 transient response for voltage applications in comparison with the literature. The designed LDO 6 linear regulator works under the input voltage of 2.8-4.8 V and provides up to 100 mA load current 7 for an output voltage of 2.6 V. 8 9 Moreover, the operational amplifier design contributes to the major reduction in the frequency 10 noise, and make sure the stability of LDO under different conditions. Furthermore, the novel LDO 11 design topology has very less dropout voltage, fast transient response and minimized power dissi- 12 pation under maximum load current, worst process corner, and maximum temperature to achieve 13 high power efficiency, maintain output voltage in the presence of fast load changes, and to lower the 14 power loss across the pass element especially at high load. Design criteria are addressed in detail. 15 16 This LDO topology is able to achieve ultra-low noise i.e. 2 /muv/√Hz for frequency >1kHz. The 17 proposed LDO is implemented in the cadence virtuoso H9A with CMOS 130 μm technology.

We present the design, fabrication, and response of a polymer-based Laterally Amplified Chemo-Mechanical (LACM) humidity sensor based on mechanical leveraging and parametric amplification. The device consists of a sense cantilever asymmetrically patterned with a polymer and flanked by two stationary electrodes on the sides. When exposed to a humidity change, the polymer swells after absorbing the analyte and causes the central cantilever to bend laterally towards one side, causing a change in the measured capacitance. The device features an intrinsic gain due to parametric amplification resulting in an enhanced signal-to-noise ratio (SNR). 11-fold magnification in sensor response was observed via voltage biasing of the side electrodes without the use of conventional electronic amplifiers. The sensor showed a repeatable and recoverable capacitance change of 11% when exposed to a change in relative humidity from 25-85%. The dynamic characterization of the device also revealed a response time ~1s and demonstrated a competitive response with respect to a commercially available reference chip.

This research refers to the creation of a method of medical technology such as a device that can collect, encode, temporarily store, and transfer electroencephalographic signals from epileptic patients for study and evaluation. For applying the specific apparatus related to neurostimulation technologies such as Deep Brain Stimulation (DBS) and Responsive Neurostimulation (RNS) the approaches followed concern three basic levels. The first level is concerned with initial modelling and creating the template for the following two stages. Further on, the second level is based on developing code for programming integrated circuits and simulation with the appropriate software. The third and final stage is the most substantial, as the transmitter’s construction is attempted at the evaluation level. In particular, more than one software and device are involved in this phase for the most realistic performance of the desired result. However, it is worth noting that the principal goal of this study is to achieve low consumption rates for the device’s complete and smooth operation. As a result, this research aims to evolve this device so that it can send data wirelessly and simultaneously provide energy efficiency.

In the field of delta-sigma modulators, reducing system power consumption without sacrificing accuracy has become a challenge. The summing circuit, as the main part of the cascade-of-integrator-in-feedforward delta-sigma modulator, consumes a significant amount of power in active summing. On the other hand, passive summing circuits have low power consumption but can cause attenuation in the summing results. This article proposes a low-power multi-bit delta-sigma modulator based on passive and attenuationless summation scheme. The summation circuit achieves multiplication of the voltage signal carried on the summation capacitor through bidirectional sampling technique, compensating for the inherent attenuation caused by passive summation, thus eliminating the need for active OTA to achieve perfect summation. A 2-order delta-sigma modulator based on 4-bit 1-order passive noise-shaping (NS) SAR quantizer is designed to verify the scheme. By combining a passive NS SAR as the 4-bit quantizer and the third-stage integrator of the system, and incorporating an energy-efficient cascode floating inverter amplifier (FIA) structure as the core active OTA, these elements have significantly enhanced the energy-efficiency of the modulator. Simulation results show that at a supply voltage of 1.2 V and a bandwidth of 20 kHz, the SNDR reaches 102.62 dB, power consumption is only 148.32 μW, and Schreier figure-of-merit (FoM) of SNDR is 183.92 dB.

The German government's ambitious goal of achieving CO2-neutrality by 2045 has prompted a focus on improving building insulation as a vital step toward energy efficiency. However, in this process, existing radiators and boilers are often left unchanged, leading to inefficiencies due to oversized heating systems. This paper presents various approaches to reduce the required radiator inlet temperature, drawing on data from 100 multifamily buildings. The approaches include heat reserve reduction, heat power shifting, uniform radiator usage, and heat requirement analysis. These approaches collectively aim to lower flow temperatures and decrease peak heat loads, reducing energy consumption, and minimizing waste in compliance with the user comfort temperature. The findings reveal that the application of these methods can lead to substantial temperature reductions, with an average decrease of 20.82 K and 7.28 K for the highest necessary flow temperature in the provided example. Furthermore, peak load reductions of 21.07% and 13.65% were achieved, demonstrating the potential to enhance energy efficiency. While each approach can be applied individually, their synergistic implementation can highly increase the efficiency of water to x heat pumps, due to the lower required flow temperatures.

This paper is an extended version of a previously reported conference paper regarding low power design for NAND Flash. As the number of bits per NAND Flash die increases with cost scaling, IO datapath speed increases to minimize the page access time with scaled CMOS in IOs. The power supply for IO buffers, namely VDDQ, has decreased from 3V to 1.2V, accordingly. In this paper, how a reduction in VDDQ can contribute to power reduction in BL path is discussed and validated. Conventionally, BL voltage of about 0.5V has been supplied from a supply voltage source (VDD) of 3V. BL path power can be reduced by a factor of VDDQ to VDD when BL voltage is supplied from VDDQ. To maintain a sense margin at sense amplifiers, the supply source for BLs is switched from VDDQ to VDD before sensing. As a result, power reduction and equivalent sense margin can be realized at the same time. The overhead of implementing this operation is an increase in BL access time of about 2% for switching the power supply from VDDQ to VDD and an increase in die size of about 0.01% for adding the switching circuit, both of which are not significant in comparison with a significant power reduction in BL path power of NAND die of about 60%. The BL path was designed in 180nm CMOS to validate the design. When the cost for powering SSD becomes quite significant especially for data center, an additional lower voltage supply such as 0.8V dedicated to BL charging for read and program verify operations may be the best option for the future.

In this paper, a new approach is proposed for designing ultra-low-power FFT (Fast Fourier Transform) system suitable for use in energy harvesting powered sensors. Bit-serial architecture is adopted to reduce the power consumption of butterfly operation. Simulation results show that, compared with state-of-the-art bit-serial and conventional parallel processors, the proposed technique is superior in terms of silicon area, power consumption, dynamic energy use due to variable precision arithmetic. A sample design of a 64-point FFT shows that the implementation can save about 40% area and 36% leakage power compared with a conventional parallel counterpart, accordingly achieving significant power benefits at a low sample rate and low voltage domain. The dynamic variation of the arithmetic precision can be achieved through a simple modification of the controller with hardware area overhead of 10% gate count.

In this letter, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows obtaining micro resolution channels at powers between 2 and 10mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

Supply chain management requires regular updates of the location of assets, which can be enabled by low power wide area networks, such as Sigfox. While it is useful to localize a device simply by its communication signals, this is very difficult to do with Sigfox because of wide area and ultra narrowband nature. On the other hand, installing a satellite localization element on the device greatly increases its power consumption. We investigated using information about nearby Wi-Fi access points as a way to localize the asset over the Sigfox network, so without connecting to those Wi-Fi networks. This paper reports the location error that can be achieved by this type of outdoor localization. By using a combination of two databases, we could localize the device on all 36 test locations with a median location error of 39 m. This shows that the localization accuracy of this method is promising enough to warrant further study, most specifically the minimal power consumption.

The goal of this paper is to present a low-cost, low-power prototype of a pulsed Ultra Wide Band UWB) oscillator and an UWB elliptical dipole antenna integrated on the same Radio Frequency (RF) Printed Circuit Board (PCB) and its digital control board for Real Time Locating System (RTLS) applications. The design is compatible with IEEE 802.15.4 high rate pulse repetition UWB standard being able to work between 6 GHz and 8.5 GHz with 500 MHz bandwidth and with a pulse duration of 2 ns. The UWB system has been designed using the CST Microwave Studio transient Electro-Magnetic (EM) circuit co-simulation method. This method integrates the functional circuit simulation together with the full wave (EM) simulation of the PCB’s 3D model allowing fast parameter tuning. The PCB has been manufactured and the entire system has been assembled and measured. Simulated and measured results are in excellent agreement with respect to the radiation performances as well as the power consumptions.

Developing a low-cost wireless energy meter with power quality measurement for smart grid applications represents a significant advancement in efficient and accurate electrical energy monitoring.In increasingly complex and interconnected electrical systems, this device is essential in various applications, such as smart grids, enabling real-time energy usage monitoring. In such a context, smart meters expand the possibilities for sustainable and efficient energy use and promote better utilization of energy sources, especially non-renewable ones. According to the 2020 International Energy Agency (IEA) research, non-renewable energy sources represent 65% of the global total. The smart meter developed in this work is built based on the ESP32 microcontroller and easily accessible components, using a user-friendly development platform that offers a cost-effective solution while ensuring reliable performance. The main objective of the smart meter development was to enhance the software and simplify the hardware. Unlike traditional meters that perform electrical parameter calculations using complex hardware circuits, this project performed the calculations directly on the microcontroller. This approach reduced the complexity of the hardware, simplifying the meter’s design. With the high-performance processing capability of the microcontroller, efficient and accurate calculations of electrical parameters were achieved without the need for additional circuits. This software-driven approach with simplified hardware brought benefits such as reduced production costs, lower energy consumption, and increased meter development and updates flexibility. Furthermore, the integrated wireless connectivity in the microcontroller enables the transmission of collected data to remote monitoring systems for later analysis. The developed smart meter offers cost, energy efficiency, and flexibility benefits. It represents an innovative, efficient, and versatile solution for smart grid applications.

This paper addresses the difficulty of balancing real-time response and low power consumption in intelligent manhole cover application scenarios. It proposes a method to distinguish normal and abnormal events by segmenting the boundary where the acceleration of the intelligent manhole cover deviates from a set threshold and lasts for a certain period, based on the difference in vibration patterns of the intelligent manhole cover when a normal event and an abnormal event occur. This paper uses digital output motion sensor data autonomous data fusion to implement the pattern mentioned above recognition algorithm, which reduces the MCU computing and working time and the overall power consumption of the system while meeting the real-time response requirements. The test results demonstrate that the method has a high rate of anomaly recognition accuracy. The method ensures the system's real-time response capability, and the actual low power consumption test demonstrates that the device can operate continuously for 9.5 years. The low power consumption index exceeds the requirements of the existing national standard, thereby resolving the issue that it is challenging to balance intelligent manhole cover abnormality recognition and low power consumption.

This paper presents a Modified Gate Diffusion Input (MGDI) design with four inputs for Quantum-dot Cellular Automata (QCA) technology. QCA is a promising nanotechnology that offers benefits such as low power consumption, and high density, making it a potential alternative to CMOS technology. The proposed planar cell design has advantages over previous designs, including a 19% reduction in the number of cells, a 29% reduction in total energy consumption, and a 44% reduction in average energy loss at the same occupancy level. The proposed block is capable of implementing 21 basic combinational functions and various sequential functions. The simulation of functions in 18nm technology and energy consumption calculation indicates that the resulting circuits have improvements of 41%, 27%, 27%, and 20% compared to multiplexers, comparators, four-bit parity circuits, and single-bit memory, respectively. Additionally, the number of cells in the proposed circuits has improved by 10%, 7%, 22%, and 19%, respectively.

We report a preliminary exploration on the low-pressure Ar-O2 plasma generated by low-frequency alternating current (AC) power supply in the low-temperature Plasma Experimental Power Supply (CTP-2000S) for the first time. The electron density 〖(n〗_e), the electron temperature 〖(T〗_e) and the electron energy distribution function (EEDF) are measured by the single Langmuir probe in this experiment. Experimental results show that the ne increases with gas pressure rising, while the ne decreases with the oxygen concentrations rising. And, a plasma density peak is also observed with the AC power supply increase. A comparison between this work and the previous results by RF source suggests that the low-frequency AC power supply may be very fruitful exploration to generate the low-pressure plasma.

A comprehensive evaluation system of rural building energy consumption from the innovative composite perspective was established, which was suitable for southwest of China. The index system was established by Brainstorming method and Delphi method, the weights of the comprehensive evaluation model were calculated by Network Process (ANP) method, the scoring criteria of all evaluation indexes were leveld based on fuzzy evaluation theory. The system model was verified by case analysis, at the countryside around Chengdu Second Circle. With the highest weight, lowest comprehensive score, and broadest range of comprehensive scores taken into consideration, three key factors affecting the target layer, namely "Percentage of Clean Energy Use", "Thermal Performance of Exterior Walls", and "Implementation Rate of Energy saving Measures". The distribution of comprehensive indicators and evaluation factors has certain spatial distribution characteristics, and the overall spatial distribution shows a characteristic of "high in the southeast and low in the northwest". Finally, Based on key factors and regional distribution characteristics, energy-saving measures have been proposed from three aspects: increasing sunrooms, adding wall insulation layers, and standardizing air conditioning temperature settings.

A comprehensive evaluation system of rural building energy consumption from a innovative composite perspective is established, which is suitable for southwest China. the brainstorming method and Delphi method were used to establish the indicator system, the ANP method was applied to calculate the weights of the comprehensive evaluation model, the scoring criteria of all evaluation indexes are constructed based on fuzzy evaluation theory, the applicability of the model is verified by an example of the countryside around Chengdu. The results showed that the score of some factors is low, whole or part area, just like the percentage of clean energy use(C24), the thermal performance of external walls(E21), the implementation of energy-saving measures(S22), were key factors affecting the target level, which has greater potential for improvement. The distribution of comprehensive indicators and evaluation factors have certain spatial distribution characteristics, the overall spatial distribution shows the characterwastic of "high in the southeast and low in the northwest". The key factors and spatial distribution characteristics found can be used as an important basis for the improvement of green energy-saving promotion measures, energy-saving retrofit programmes were proposed in terms of additional solar room, energy-saving of external walls and air-conditioning temperature setting guidance.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

A significant electromotive force is induced in the rotor circuit of a doubly fed induction generator (DFIG) due to its high vulnerability to grid faults. Therefore, the system performance must be increased with appropriate control actions that can successfully offset such abnormalities in order to provide consistent and stable operations during grid disturbances. In this regard, this paper presents a solution based on a combination of an energy storage-based crowbar and a rotor-side crowbar that makes the effective transient current and voltage suppression for wind-driven DFIG possible. The core of the solution is its ability to restrict the transient rotor and stator overcurrents and DC-link overvoltages within their prescribed limits, aiming to protect the DFIG and power converters, and consequently, improve the system’ ability to ride-through faults. Further, the capacity of an energy storage device for transient suppression is estimated. Finally, simulation results show that the proposed approach is effective in achieving transient control objectives precisely and maintaining a stable grid connection during the faults.

In this article we present a deployment of 11 nodes using the three different SUN (Smart Utility Network) modulation schemes, as defined in the IEEE 802.15.4-2015 standard. The nodes were deployed in a 110.044 m2 warehouse for 99 days, and the resulting dataset contains a total of 10.710.868 measurements with RSSI (Received Signal Strength Indicator), CCA (Clear Channel Assessment) and PDR (Packet Delivery Ratio) values. The analyzed results show a high variability in average RSSI (i.e., between -82.1 dBm and -101.7 dBm) and CCA (i.e., between -111.2 dBm and -119.9 dBm) values, which are caused by the effects of multi-path propagation and external interference. Despite being above the sensitivity limit for each modulation, this values result in poor average PDR values (i.e., from 65.9% to 87.4%), indicating that additional schemes are required for low-power wireless communications to meet the dependability requirements of industrial applications. For that purpose, we also introduce the concept of modulation diversity, which can be combined with packet repetition to meet such requirements (i.e., PDR>99%) while minimizing the energy expenditure of nodes and meeting regulatory constraints.

Carbon dioxide (CO2)miscible fracturing huff and puff technology plays a pivotal role in enhancing the recovery rate of crude oil, particularly in reservoirs with challenging physical properties, strong water sensitivity, high injection pressure, and complex water injection dynamics. In this study, the oil-increasing mechanism and huff and puff effect of CO2 miscible fracturing fluid are investigated through a comprehensive experimental approach. Specifically, experiments on PVT gas injection expansion, minimum miscible pressure, and CO2 miscible fracturing huff and puff are conducted on the G fault block reservoir in J Oilfield. The findings demonstrate that injecting CO2 into reservoirs leads to oil volume expansion, viscosity reduction, and saturation pressure increase. Additionally, the inclusion of solubilizers and viscosity reducers further enhances the efficiency of crude oil extraction. Solubilizers not only improve oil recovery but also reduce the minimum miscible pressure required for effective CO2 dispersion. Furthermore, the shut-in time, permeability, and huff and puff method all have considerable impacts on huff and puff recovery rate. This study offers valuable technical insights, supporting the application of CO2 miscible fracturing huff and puff technology to enhance oil recovery in low-permeability reservoirs.

Under the "dual carbon" target in China, virtual power plants (VPPs) play an important role in improving grid security and promoting clean and low-carbon energy transformation. VPPs can integrate and control distributed resources to participate in the energy market and make full use of distributed resources. However, the intermittency and volatility of renewable energy and the "heat-driven" working mode of CHP units create contradictions that seriously affect the peak-shaving ability of VPPs and lead to high carbon emissions. To solve these problems, this paper aggregates CHP units, wind power, photovoltaics, carbon capture, hydrogen energy storage, and electric boilers into a new type of virtual power plant. The "hydrogen energy storage-electric boiler" joint decoupling CHP working mode is used to strengthen the coupling relationship between electric-thermal-hydrogen load. At the same time, a tiered carbon trading mechanism is considered, with the net profit of the VPP as the optimization objective, balancing economic and environmental considerations. A low-carbon economic dispatch model for VPPs is established, and a genetic algorithm is used for optimization. Three different scheduling strategies are set, and simulations are conducted in three different seasonal scenarios. The results show that the net profit in the cooling season increased by 50.4%, and carbon emissions decreased by 42.3%. In the transitional season, the net profit increased by 39.2%, and carbon emissions decreased by 44.9%. In the heating season, the net profit increased by 19.4%, and carbon emissions decreased by 43.4%. Overall, the proposed dispatch strategy can improve the new energy consumption capacity and total revenue of VPPs while achieving the goal of reducing carbon emissions.

In the paper, an improved smart meter data-based three-stage algorithm to calculate the power/energy losses in the three-phase networks with the voltage level below 0.4 kV (low voltage - LV) is presented. In the first stage, a loading function of input data was built having as main feature the working at the same time with files from the database of smart metering system (SMS) containing the hourly electricity records, and files including the characteristic load profiles established by the Distribution Network Operator (DNO) for the consumers with standard energy meters depending the following factors: consumption class, day and season. In the second stage, a function which is based on the work with the structure vectors was implemented to identify easy the configuration of analysed networks. In the third stage, an improved version of forward/backward sweep-based algorithm was proposed to calculate fast the power/energy losses to three-phase LV distribution networks in balanced and unbalanced regime. A real LV rural distribution network from a pilot zone belonging to a Distribution Network Operator (DNO) from Romania was used to confirm the accuracy of the proposed approach. The comparison with the results obtained using the DigSilent PowerFactory Simulation Package certified the performance of the algorithm, the mean absolute percentage error (MAPE) being 0.94%.

With the development of energy internet, integrated energy system can effectively reduce carbon emissions and improve the utilization of renewable energy. In this paper, a low-carbon optimal scheduling model of integrated energy system considering heat loss of heat network pipeline is proposed. Based on the study of concentrating solar power (CSP) plant and heat storage tank (HS), an optimal scheduling model is established, which takes system operation cost, environmental pollution and penalty cost of abandoning wind and solar energy as objectives. Through the analysis of example results, it is proved that the model proposed in this paper can achieve the goal of reliable, low-carbon and economic operation of the system. At the same time, it shows that CSP unit can reduce the operation cost of system and increase energy coupling and utilization.

During the conceptual and preliminary design stage of a ship, designers need to ensure that the selected principal dimensions and parameters are good enough to deliver a stable ship (statically and dynamically) besides deadweight and speed. To support this, the initial intact stability of the proposed ship is required to be calculated, and in doing so, the lightship weight and its detailed breakdown are necessary to be known. After hull steel weight, machinery weight, mainly, marine propulsion and power generation machinery, play a vital role in the lightship weight estimate of a ship due to its robustness. The correct estimation of respective weights improves the accuracy of calculating a ship's initial stability typically to be designed and built. Hence, it would be advantageous for the designer to convince the ship owner. A total of 3006 marine propulsion (main marine diesel) engines and 348 power generation (auxiliary marine diesel) engines/generators of various power output (generators output for auxiliary engines), engine RPM and cylinder number of different engine makers are collected. These are analyzed and presented in both tabular and graphical forms to demonstrate the possible relationship between marine propulsion engine weight and power generation engine weight, and their respective power output, RPM, cylinder number, power-RPM ratio and power-RPM ratio per cylinder.In this article, the authors have attempted to investigate the behavior of marine propulsion engine weight and power generation engine/generator weight regarding engine power output, generator power output, engine RPM and cylinder number (independent variables). Further attempts have been made to identify those independent variables that influence the weight of the marine propulsion engine and power generation engine/generator (dependent variables), and their interrelationships. A mathematical model has thus been developed and proposed, as a guiding tool, for the designer to estimate the weight of main and auxiliary engines more accurately during the conceptual and preliminary design stage.

This research proposes a roof-mounted auxiliary power supply (APS) system for 600VDC low-floor light rail vehicle (LRV). The proposed APS system consists of five parallel-connected dc-ac inverter modules (modules 1-5). The inverter modules 1 and 2 are three-phase dc-ac inverters for compressor motors of the cooling system, and the inverter modules 3 and 4 are three-phase dc-ac inverters for air pump motors of the braking system. The inverter module 5 is single-phase dc-ac inverter for 220VAC power supply for onboard electric loads. Simulations and experiments were carried out under variable load torque and output frequency for modules 1 – 4; and under full and no resistive loads for the inverter module 5. The measured total input current and total input power of the proposed APS system under full load condition are 118.76A and 71.25kW. Essentially, the proposed APS system is operationally applicable to the 600VDC low-floor RLV. Besides, the novelty of this research lies in the use of five parallel-connected inverter modules, unlike in the conventional APS systems which require three-phase output transformer or isolated dc-dc converter. Specifically, the proposed APS system requires neither three-phase output transformer nor isolated dc-dc converter.

Nowadays, energy decarbonization due to the integration of renewable energy sources presents important challenges to overcome. The intermittent nature of photovoltaic systems reduces power quality by producing voltage variations and frequency deviations in electrical systems networks, especially, in weak and isolated distribution systems in developing countries. This paper presents a power smoothing method improving the low pass filter and moving average for grid-connected photovoltaic system, the novel method includes state-of-charge monitoring control of the supercapacitors energy storage system to reduce the fluctuations of photovoltaic power at the point of common coupling. A case study for a microgrid in a high-altitude city in Ecuador is presented with exhaustive laboratory tests using real data. The ultimate goal of this research is to improve energy power quality in electrical distribution systems to cope with the growth of renewable penetration.

Creating new business models is crucial for the implementation of clean technologies for industrial decarbonization. With incomplete knowledge of market processes and uncertain conditions, assessing the prospects of a technology-based business model is challenging. This study combines business model innovation, system dynamics and exploratory model analysis to identify new business opportunities in a context of socio-technical transition and assess their prospects through simulation experiments. Furthermore, insights are visualized in a roadmap to coordinate action among the actors involved. This combination of methods is applied to the case of a business model aiming at ensuring stability of the electrical grid by centralizing the management of flexible loads in industrial companies. A system dynamics model was set up to simulate the diffusion of flexible electrification technologies. Through scenario definition and sensitivity analysis, the influence of internal and external factors on diffusion was assessed. Results highlight the central role of energy costs and customer perception. The chosen combination of methods allowed the formulation of concrete recommendation for coordinated action, explicitly accounting for the various sources of uncertainty. We suggest testing this approach in further business model innovation contexts.

Creating new business models is crucial for the implementation of clean technologies for industrial decarbonization. With incomplete knowledge of market processes and uncertain conditions, assessing the prospects of a technology-based business model is challenging. This study combines business model innovation, system dynamics and exploratory model analysis to identify new business opportunities in a context of socio-technical transition and assess their prospects through simulation experiments. Furthermore, insights are visualized in a roadmap to coordinate action among the actors involved. This combination of methods is applied to the case of a business model aiming at ensuring stability of the electrical grid by centralizing the management of flexible loads in industrial companies. A system dynamics model was set up to simulate the diffusion of flexible electrification technologies. Through scenario definition and sensitivity analysis, the influence of internal and external factors on diffusion was assessed. Results highlight the central role of energy costs and customer perception. The chosen combination of methods allowed the formulation of concrete recommendation for coordinated action, explicitly accounting for the various sources of uncertainty. We suggest testing this approach in further business model innovation contexts.

Oxidative stress is one of the primary instigators of the onset of various human ailments, including cancers, cardiovascular diseases, and dementia. Particularly, oxidative stress has a severe effect on low-density lipoprotein (LDL) oxidation, leading to several detrimental health effects. Thereof, in this study, the effect of beeswax alcohol (BWA) was evaluated to prevent LDL oxidation, enhancement of paraoxonase 1 (PON-1) activity of high-density lipoprotein (HDL), and zebrafish embryo survivability. Furthermore, the implication of BWA consumption on the oxidative plasma variables was assessed by a preliminary clinical study on middle and older human subjects (n=50). Results support BWA augmentation of PON-1 activity in a dose-dependent manner (10-30 μM), which was significantly better them the effect exerted by coenzyme Q10 (CoQ10). Moreover, BWA significantly curtails CuSO4 (final 0.5 μM) evoked LDL/apo-B oxidation and a marked reduction of lipid peroxidation in LDL. The transmission electron microscopy (TEM) analysis revealed a healing effect of BWA towards the restoration of LDL morphology and size impaired by the exposure of Cu2+ ions (final 0.5 μM). Additionally, BWA counter carboxymethyllysine (CML, 500 ng) induced toxicity and rescued zebrafish embryos from development deformities and apoptotic cell death. A completely randomized, double-blind, placebo-controlled preliminary clinical study on middle and older-aged human subjects (n=50) exhibited that 12 weeks of BWA (100 mg/day) supplementation efficiently diminished serum malondialdehyde (MDA), total hydroperoxides, and enhanced total antioxidant status by 25%, 27%, and 22%, respectively, compared to the placebo control and baseline values. Furthermore, the consumption of BWA did not exhibit any noteworthy changes in anthropometric profile, lipid profile, glucose levels, and biomarkers pertinent to kidney and liver function, thus confirming the safety of BWA for consumption. Conclusively, BWA prevents LDL oxidation, enhances PON-1 activity in HDL, and has a positive impact on the oxidative variables of human subjects.

The rapid advancement of Earth observation systems and satellite networks driven by commercial space has led to a significant increase in the number of remote sensing satellites, thereby establishing the groundwork for all-weather, continuous cluster collaborative observation. Following anti-irradiation hardening measures, low-cost commercial off-the-shelf (COTS) devices are effectively operated within intricate space environments, leading to substantial enhancements in on-orbit computing capabilities of individual satellites. Leveraging the on-board distributed processing framework, it fully utilizes wide-area scattered space computing resources and automatically establishes a network of neighboring satellites through inter-satellite communication links to construct a spatially distributed and computationally cooperative space cloud computing environment. This enables the sharing of space computing resources and facilitates satellite-based mission coordination, reducing reliance on ground-based remote sensing satellite services while enhancing the response efficiency of remote sensing application services. The present paper pro-vides a comprehensive review of the current development status, existing challenges, and problems faced by space-based remote sensing on-orbit processing platforms and on-board intelligent processing algorithms, starting from the immediate application requirements of remote sensing satellite in-orbit processing. In view of the anticipated surge in large-scale computing resources in space, a distributed remote sensing satellite data processing architecture based on large-scale on-board computing power is constructed, and the architecture is designed in detail from the aspects of physical architecture, software architecture, workflow and key technologies. Finally, three real-time service scenarios that align with the construction content of an ultra-low orbit satellite constellation and 6G technology have been designed to provide solutions and references for subsequent development of space-based intelligent remote sensing constellations.

In this work, an analog front-end (AFE) circuit for Electrocardiogram (ECG) detection system has been designed, implemented, and investigated in an industry-standard Cadence simulation framework using advanced technology node of 45 nm. The AFE consists of an instrumentation amplifier, a Butterworth band-pass filter (with fifth-order low-pass and second-order high-pass sections), and a second-order notch filter- all are based on two-stage, Miller-compensated operational transconductance amplifiers (OTA). The OTAs have been designed employing the $g_m/I_D$ methodology. Both the pre-layout and post-layout simulation were carried out. The layout consumes an area of 0.0058 mm$^2$ without the resistors and capacitors. Analysis of various simulation results were carried out for the proposed AFE. The circuit demonstrates a post-layout bandwidth of 239 Hz with a variable gain between 44 to 58 dB, a notch depth of -56.4 dB at 50.1 Hz, a total harmonic distortion (THD) of -59.65 dB (less than 1\%), an input referred noise spectral density of $

Climate change is increasing air temperatures and altering the precipitation and hydrological re-gime on a global scale. Challenges arise when assessing the impacts of climate change on the local scale for water resources management proposes, especially for low mountain headwater catch-ments that not only serve as important water towers for local communities, but also have distinct hydrological characteristics. Until now, no low flow or hydrological drought studies have been carried out on the Lauter River. This study is unique in that it compares the Lauter River, a transboundary Rhine tributary with a nearby station on the River Rhine just below its confluence at the French-German border. The Lauter catchment is a mostly natural, forested catchment, however, its water course has been influenced by past and present cultural activities. Climate change disturbances cascade through the hydrologic regime right down to the local scale. As we are expecting more low flow events, the decrease in water availability could cause conflicts be-tween different water user groups in the Lauter catchment. However, the choice of different methods for identifying low flow periods may cause confusion for local water resources manag-ers. Using flow rate time series of the Lauter River between 1956 and 2022 we compare for the first time three low flow identification methods: the variable threshold method (VT), the fixed threshold method (FT), and the Standardized Streamflow Index (SSI). Similar analyses are applied and compared to the adjacent Maxau station on the Rhine River for the same time period. This study aims at 1) interpreting the differences amongst the various low flow identification methods and 2) revealing the differences in low flow characteristics of the Lauter catchment compared to the Rhine River. It appears that the FT reacts faster to direct climate or anthropogenic impacts whereas VT is more sensitive to indirect factors such as decreasing subsurface flow which is typical for small headwater catchments, such as the Lauter where flow dynamics react faster to flow disturbances. Abnormally low flow during the early Spring in tributaries such as the Lauter can help predict low flow conditions of the Rhine River during the following half year and espe-cially for the summer. The results could facilitate Early Warning of hydrological droughts and drought management for water users in the Lauter catchment and further downstream along some of the Rhine.

As the PCIe 6.0 specification places higher requirements on signal integrity and transmission la-tency, it becomes especially important to improve signal transmission performance at the physical layer of the transceiver interface. Retimer circuit as a key component of high-speed serial interface, its delay and jitter size directly affect the overall performance of PCIe. For the conventional Retimer circuit with large latency and low jitter performance, this paper proposes a low latency and low jitter Retimer circuit based on CDR+PLL architecture for PCIe 6.0, using a jitter canceling filter circuit to eliminate the frequency difference between the retiming clock and data, reduce the retiming clock jitter, and improve the quality of Retimer output data; The data is sampled using the retiming clock and then output, avoiding the problem of large penetration latency of con-ventional Retimer circuits. The circuit is designed using CMOS 28nm process. Simulation results show that when 112Gbps PAM4 data is input to the Retimer circuit, the Retimer penetration la-tency is 27.3 ps, which is 83.5% lower than the conventional Retimer structure; the output data jitter is 741 fs, a 31.4% reduction compared to the conventional Retimer structure.

Low Power Wide Area Networks (LPWAN) enable a growing number of Internet-of-Things (IoT) applications with large geographical coverage, low bit-rate, and long lifetime requirements. LoRa (Long Range) is a well-known LPWAN technology that uses a proprietary Chirp Spread Spectrum (CSS) physical layer, while the upper layers are defined by an open standard - LoRaWAN. In this paper, we propose a simple yet effective method to improve the Quality-of-Service (QoS) of LoRa networks by fine-tuning specific radio parameters. Through a Mixed Integer Linear Programming (MILP) problem formulation, we find optimal settings for the Spreading Factor (SF) and Carrier Frequency (CF) radio parameters, considering the network traffic specifications as a whole, to improve the Data Extraction Rate (DER) and to reduce the packet collision rate and the energy consumption in LoRa networks. The effectiveness of the optimization procedure is demonstrated by simulations, using LoRaSim for different network scales. In relation to the traditional LoRa radio parameter assignment policies, our solution leads to an average increase of 6% in DER, and a number of collisions 13 times smaller. In comparison to networks with dynamic radio parameter assignment policies, there is an increase of 5%, 2.8%, and 2% of DER, and a number of collisions 11, 7.8 and 2.5 times smaller than equal-distribution, Tiurlikova's (SoTa), and random distribution, respectively. Regarding the network energy consumption metric, the proposed optimization obtained an average consumption similar to Tiurlikova's, and 2.8 times lower than the equal-distribution and random dynamic allocation policies. Furthermore, we approach the practical aspects of how to implement and integrate the optimization mechanism proposed in LoRa, guaranteeing backward compatibility with the standard protocol.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

A novel low-power MOS-only voltage reference is presented. The Enz-Krummenacher-Vittoz (EKV) model is adopted to provide a new perspective on the operating principle. The normalized charge density, introduced as a new variable, serves as an indicator when trimming the output temperature coefficient. The proposed voltage reference consists of a specific current generator and a 5-bit trimmable load. Thanks to the well-match between the current source stage and the output stage, the non-linear temperature dependence of carrier mobility is automatically canceled out. The circuit is designed in 55 nm COMS technology. The operating temperature ranges from -40 ∘C to 120 ∘C. The average temperature coefficient of the output voltage can be reduced to 21.7 ppm/∘C by trimming. The power consumption is only 23.2 nW with a supply voltage of 0.8 V. The line sensitivity and the power supply rejection ratio at 100 Hz are 0.011 %/V and -89 dB respectively.

Low volatility ETFs have become popular in recent year because investors are starting to understand the advantages involved in investing in those ETFs compared to traditional index investment. In this research I have examined the performance of six popular low volatility ETFs, four of them invest in U.S stocks and the other two invest in other developed and emerging markets. Results have pointed out that not only five of the low volatility ETFs have exposed their investors to lower risk, four of them have also produced higher returns. The advantage of investing in low volatility ETFs is prominent in the U.S stock market. All three sizes of stocks categories (Large, Mid and Small Capitalization) low volatility ETFs have outperformed their indexes bench marks in terms of risk and returns. For the non U.S stock investing, while no advantage have been found for investing in low volatility ETFs for developed countries, significant lower risk was found for emerging markets.

Logistics industry has been found to be among the key sources of carbon emission. In Vietnam logistics industry, there is a considerable difference between the number of foreign and Vietnamese firms as well as the proportion of markets that they are taking. This study is to research the low-carbon emission measures conducted by domestic and foreign invested logistics service providers (LSPs) and compare the results of the two groups. Both qualitative and quantitative approaches are applied. Literatures in relevant fields are reviewed and expert opinions are taken for structuring a questionnaire which was later distributed to 279 LSPs, with 166 returned and 159 being valid for data calculation. The results imply that there are differences in extension of applications of low-carbon practices between foreign and domestic firms. Except for transport mode switch and energy-saving lighting, the other practices witness that adoption levels of foreign LSPs are higher than their counterparts, which is possibly thanks to their global operation, more comfortable capital resources and awareness level of green initiative necessity. In conclusion, a comparison between the application conducted by foreign-invested firms and domestic ones, which has not been investigated before, was made.

HER2-low and ultra-low breast cancer (BC) have been recently proposed as new subcategories of HER2 BC, re-considering the immunohistochemical negative score of 0, 1+ or score of 2+/in situ hybridization (ISH) negative phenotype. In the present review we have outlined the needed criteria to exactly distinguish HER2 low and ultra-low BC. Recent clinical trials have demonstrated significant clinical benefits of novel HER2 directing antibody-drug conjugates (ADCs) in treating these group sof tumors. In particular, Trastuzumab-deruxtecan (T-Dxd), a HER2-directing ADC has been recently approved by the U.S. Food and Drug Administration as the first targeted therapy to treat HER2-low BC. Furthermore, ongoing trials, such as the DESTINY-Breast06, are currently evaluating ADCs in patients with HER2-ultra low BC. Finally we hope that new guidelines may help to codify HER2 low and ultra-low BC, increasing our knowledge of tumor biology and improving a targetable new therapeutical treatment.

Multidisciplinary Design Optimization (MDO) is the most active field in the design of current complex system engineering, which is possessed with such two difficulties as subsystem information exchange and analytical and computational complexity of systems. Therefore, an improved collaborative optimization algorithm based on ANN (artificial neural network) response surface was proposed dependent on the consistency constraint algorithm and concurrent subspace algorithm. As an optimization method with secondary structure, it satisfied only local constraints in discipline layer, but provided a coordinated mechanism for interdisciplinary conflict in system layer. Finally, it was applied in the multidisciplinary design optimization of autonomous underwater vehicle (AUV). As shown from the result, the MDO convergence stability and reliability of low resistance, low noise and high maneuvering performance of the AUV shape can be ensured by the improved collaborative optimization algorithm, thus verifying the effectiveness of the algorithm.

Many studies utilize sensors to measure foot plantar pressure and analyze gait patterns, often focusing on assessing weight-bearing symmetry or asymmetry compared to control groups. However, a critical question arises: does the selection of the control group significantly impact study outcomes? Does chronic low back pain affect foot plantar pressure measurements? This experimental study involved 23 participants, including healthy individuals and those without foot disorders but with chronic low back pain. Dynamic foot pressure measurements were conducted using the Ortopiezometr, and data were analyzed using the "Steps" program. Participants were divided into two groups: Group 1 comprised completely healthy individuals, while Group 2 consisted of individuals without foot problems but with moderate chronic low back pain. The findings highlight a prevalence of energy release in the forefoot sensors compared to the hindfoot for both the right and left legs in most cases. Even among healthy volunteers, achieving perfect symmetry in the maximum values on the sensors for the right and left feet was a challenge. Results showed no statistically significant differences in energy released on specific sensors or duration of gait phases between the groups. Essentially, this suggests that foot pressure patterns are comparable between healthy individuals and those with low back pain. The use of sensor-equipped inserts for pedobarographic examinations indicates that, in cases of degenerative changes in the lumbar and sacral spine without accompanying acute pain, gait patterns resemble those of the healthy population.

Background: Low birth weight (LBW) is a major public health problem in low-income countries. Infants born with LBW are at increased risk of neonatal mortality, have poorer school performance, and are more likely to develop respiratory and cardiovascular diseases in adulthood. Methods: An unmatched case–control study was conducted in five maternity wards in the Kenge Health Zone, involving 159 mother–newborn pairs. Data analysis was performed using STATA 18.0 software. Bivariate and multivariate analyses were used to determine the associations between independent variables and LBW. Results: Determinants of low birth weight were maternal short stature (height < 155 cm) (adjusted odds ratio (AOR): 3.90; 95% confidence interval (CI): 1.66–9.13), maternal non-indigenous Yaka ethnic group (AOR: 2.39; 95% CI: 1.01–5.66), having attended fewer antenatal care (ANC) sessions (AOR: 0.73; 95% CI: 0.53–0.99), and inadequate maternal dietary diversity (AOR: 3.97; 95% CI: 1.25–12.62). Conclusions: Increased education and awareness of dietary diversity as an indicator of dietary quality in women of childbearing age, especially during pregnancy, along with regular follow-up of antenatal care visits and behavior change communication targeting pregnant women, can help health professionals address dietary taboos and reduce the incidence of LBW.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

Poly(2,6-dimethyl phenyl oxide) (PPO) is known for its low dissipation factor. To achieve insulating materials with low dissipation factor for high-frequency communication application, a monomer-type benzoxazine (P-APPO) and a main-chain-type benzoxazine (BPA-APPO) were prepared from an amine end-capped oligo (2,6-dimethyl phenylene oxide) (APPO). The APPO was prepared from a nucleophilic substitution of a phenol-end capped oligo (2,6-dimethyl phenylene oxide) (a commercial product, SA 90) with fluoronitrobenzene, and followed by catalytic hydrogenation. After self-curing or curing with a dicyclopentadiene-phenol epoxy (HP 7200), thermosets with high-T_g and low-dissipation factor can be achieved. Furthermore, the resulting epoxy thermosets show better thermal and dielectric properties than those of epoxy thermoset cured from its precursor SA90, demonstrating it is a successful modification in simultaneously enhancing the thermal and dielectric properties.

To achieve rapid post-earthquake repair of self-centering ribbed floor flat beam frame structures, a ductile hybrid joint consisting of dog bone weakened energy dissipating steel bars connected to the upper and lower column sections through high-strength threads based on the damage control design concept is proposed. By moving the ductile energy dissipating zone out to the locally weakened section of the energy dissipating steel bars and the locally unbonded prestressed steel bars in the core area, the residual deformation was limited and the seismic performance was improved. Based on the working principle of hybrid joints, low cycle loading tests were conducted on two joint specimens to analyze the influence of lateral prestress on the seismic performance of the hybrid joints. Numerical modeling methods were used to compare the position of the energy-consuming steel bars in the composite layer and the friction performance of joints. The research results indicated that the hybrid joint had stable load-bearing, deformation, and energy dissipation capabilities, with damage primarily concentrated on the energy-consuming steel bars. Even at an inter-story displacement angle of 5.5%, the upper and lower column segments remained elastic. After unloading, the connection seam at the joint was closed, and the self-centering performance was good. When the inter-story displacement angle reached 5.5%, the lateral prestress increased from 150 kN to 250 kN, the ultimate bearing capacity of the joint increased by 16.3%, and the cumulative energy consumption increased by 30.0%. The influence of the friction coefficient of the joint surface on the structural performance was set at a threshold of 0.7. When it was less than the threshold, the ultimate bearing capacity and initial stiffness of the joint increased with an increase in the friction coefficient. After reaching the threshold, the increase in the ultimate bearing capacity of the joint slowed down, and the rate of stiffness degradation gradually accelerated. This joint had excellent seismic performance and can also achieve post-earthquake repair of structures.

The influence of the Fe2O3 addition amount on the dephosphorization of hot metal at 1623 K with the slag of the low basicity (CaO/SiO2) of about 1.5 was investigated by using high-temperature laboratorial experiments. With increasing the Fe2O3 addition amount, the contents of [C], [Si], [Mn] and [P] in hot metal at the end of dephosphorization decrease, and the corresponding removal ratios increase. The P2O5 content in slag increases, and the CaO and SiO2 contents in slag decrease. The phosphorus mainly exists in the form of the nCa2SiO4-Ca3(PO4)2 solid solution in the phosphorus-rich phase and the value of coefficient n decreases from 20 to 1 with increasing the Fe2O3 addition amount from 5 g to 30 g. With increasing the Fe2O3 addition amount, the oxygen potential and activity at the interface between the slag and hot metal increase. When the oxygen potential and the oxygen activity at the interface are greater than 0.72×10-12 and 7.1×10-3, respectively, the dephosphorization ratio begins to increase rapidly. With increasing the Fe2O3 addition amount to 30 g, the ratio of the Fe2O3 addition amount to theoretical calculation consumption is around 175%, and the dephosphorization ratio reaches the highest value of 83.3%.

Low 25 OH vitamin D (25(OH)D) in preterm infants is a risk factor of bronchopulmonary dysplasia (BPD), but increased supplementation failed to demonstrate beneficial effect on BPD. In neonatal animal models, deficiency and excessive vitamin D exposure have been associated with increased mortality and lung histological alterations evocative of BPD. Our hypothesis is that 25(OH)D levels ≥ 120nmol/L is also a risk factor for BPD or death. This retrospective single-center cohort study included all infants born <31 weeks gestational age without major malformation with at least a determination of 25(OH)D <36 weeks corrected age and no determination <50 nmol/L. Routine 25(OH)D determination was performed at 1 month and monthly thereafter. A total of 175 infants were included. Infants with BPD or who died had a significantly lower term and weight, but a similar frequency of 25(OH)D ≥120nmol/L (50.5% vs 43.9%, p=0.53). The logistic regression identified weight (OR 0.997, 95%CI [0.995-0.998]) and term (OR 0.737, 95%CI [0.551-0.975]) as significantly associated with BPD or death; the occurrence of excessive 25(OH)D was not significantly associated (OR 1.029, 95%CI [0.503-2.093]). The present study did not demonstrate any significant association between excessive 25(OH)D after one month of age and BPD or death.

An accurate flux measurement of low-energy charged particles trapped in the magnetosphere is necessary for space weather characterization and to study the coupling between the lithosphere and magnetosphere, which allows for the investigation of the correlations between seismic events and particle precipitation from Van Allen belts. In this work, the project of a CubeSat space spectrometer, the Low-Energy Module (LEM), is shown. The detector will be able to perform an event-based measurement of the energy, arrival direction, and composition of low-energy charged particles down to 0.1 MeV. Moreover, thanks to a CdZnTe mini-calorimeter, the LEM spectrometer also allows for photon detection in the sub-MeV range, joining the quest for the investigation of the nature of Gamma-ray bursts. The particle identification of the LEM relies on the ΔE−E technique performed by thin silicon detectors. This multipurpose spectrometer will fit within a 10 × 10 × 10 cm3 CubeSat frame, and it will be constructed as a joint project between the University of Trento, FBK, and INFN-TIFPA. To fulfil the size and mass requirements, an innovative approach, based on active particle collimation, was designed for the LEM; this avoids the heavy/bulky passive collimators of previous space detectors. In this paper, we will present the LEM geometry, its detection concept, the results from the developed GEANT4 simulation, and some characterisations of a candidate silicon detector for the instrument payload.

Emerging risk factors for childhood (<5 years) anemia cases in low-income countries have not been limited to COVID-19 and the spread of infectious diseases, hidden hunger, and other economic factors. Yet the effects of climatic factors, such as ambient temperatures, on child anemia have been in its infancy. In this population-based study, we study the region-specific associations between child anemia and ambient temperatures in 43 countries of Africa from 2000-2019. Using generalized linear regression models, we found that after adjusting for key covariates, the risk that temperatures pose on child anemia varies across the four African regions (Western, Eastern, Central, and Southern). This suggests that ambient temperatures have varying effects on child anemia by region. Other studies are needed in other low-income settings to expand our findings.

Umbria is an Italian region with a highly fragmented water supply, with many small water distribution systems fed by local sources. The chlorination in these small water systems faces many difficulties related to the high demand variation, low economic relevance, and access to infrastructures. As a result, there are many noncompliances with the quality of the supplied water, which causes a decrease in the performance indicators and tariff. This research investigates the possibility of using a low-cost chlorination system to consider different environmental conditions (e.g., temperature variations of water and environment, pH, ...) and discontinuous consumption. A device for this specific use is developed and tested by laboratory tests and is ready for use in the field.

Tropical rock lobsters (Panulirus ornatus) are a highly cannibalistic species with intermoult animals predominantly attacking animals during ecdysis (moulting). Rapid, positive characterisation of pre-ecdysis lobsters may open a pathway to disrupt cannibalism. Ecdysial suture line development is considered for pre-ecdysis recognition with suture line definition compared for lobsters emerged and immerged, using white, near ultraviolet (365 nm), near infrared (850 nm) and spe-cialty Osram SFH 4737 broadband IR LEDs against a reference of intermoult lobsters with no suture line development. An alternative pre-ecdysis recognition strategy used a novel low-cost spectral camera composed of the Sony IMX219, AMS AS7265x spectral sensors and Osram SFH 4737 broadband infrared LEDs. Images and data using the novel low-cost spectral camera was acquired from intermoult, pre-ecdysis, and post-ecdysis lobsters. Compared with the white light appear-ance, suture line definition was enhanced under 850 nm, 365 nm, and SFH 4737 LEDs for immerged lobsters, while the 850 nm LED achieved the best suture line definition of emerged lobsters. The spectral camera was unable to characterise pre-ecdysis. A least squares regression for binary classification decision boundary successfully separated 86.7% of post-moult lobsters. Achieving post-moult characterisation validated the speculative exploratory approach in developing this novel low-cost spectroscopy tool.

GNSS is nowadays a standard tool for monitoring and studying the Earth’s dynamic environment. However, the development of dense GNSS measurements remains limited in many experiments by the cost of geodetic-class equipments allowing to achieve the high precision required by many applications. Recently, multi-constellation, multi-frequency, low-power and, above all, less expensive GNSS electronic chips have become available. We present a prototype of a low-cost, open-source multi-GNSS station. Our prototype comprises a dual-frequency GNSS chip, a calibrated antenna, a Raspberry Pi card and a 4G key for data transmission. The system is easy to deploy in the field and allows precise positioning in real time and post-processing. We assess the performance of our prototype in terms of raw data quality, and quality of the obtained high rate and daily position one-year-long time series. Our results demonstrate a quality equivalent to geodetic-class equipment and better quality than other low-cost systems proposed so far.

The manufacturing geometrical variability in axial compressors is a stochastic source of uncertainty, implying that the real geometry differs from the nominal design. This causes the real geometry to lose the ideal axial symmetry. Considering the aerofoils of a stator vane, the geometrical variability affects the flow traversing it. This impacts the downstream rotor, especially when considering the aeroelastic excitation forces. Optical surface scans coupled with a parametrization method allow for acquiring the information relative to the real aerofoils geometries. The measured data are included in a multi-passage and multi-stage CFD setup to represent the mistuned flow. In particular, low excitation harmonics on the rotor vane are introduced due to the geometrical deviations of the upstream stator. The introduced low engine orders as well as their amplitude depend on the stator geometries and their order. A method is proposed to represent the phenomena in a reduced CFD domain, limiting the size and number of solutions required to probabilistically describe the rotor excitation forces. The resulting rotor excitation forces are reconstructed as a superposition of disturbances due to individual stator aerofoils geometries. This indicates that the problem is linear in in the combination of disturbances from single passages.

Disseminated or military tuberculosis (TB) is defined as the presence of at least two non-contiguous sites of Mycobacterium tuberculosis, occurring as a result of progressive primary infection, reactivation and spread of a latent focus or due to iatrogenic origin. Disseminated TB represents a life-threatening condition, especially in at-risk children and when the diagnosis and treatment are delayed. We report on a case of a 3-year old boy who presented with long-lasting unrecognised disseminated TB that was successfully managed in a low-resource setting.

This paper presents high-resolution digital measurements at low cost, combining oversample and averaging. Experiments of processing data between samples and between multiple temperature sensors in the same environment are conducted. They provide results with effective increase in the analog to digital converter bits, in correspondence with the minimization on the effects of noise. It is shown that averaging a set of small, low-cost sensors at a small microcontroller can give flexible access to improved measurement accuracy.

The production and secretion of very-low density lipoproteins (VLDL) by hepatocytes has a direct impact on liver fat content as well as the concentration of cholesterol and triglycerides in the circulation and thus affects liver and cardiovascular health, respectively. Importantly, excess caloric intake and lack of physical activity are associated with overproduction of VLDL, hepatic steatosis, and increased levels of atherogenic lipoproteins. Cholesterol as well as triglycerides in remnant particles after VLDL lipolysis are risk factors for atherosclerotic cardiovascular disease (ASCVD) and have garnered increasing attention over the last few decades. To date, however, increased risk of ASCVD is not the only concern when considering today’s cardiometabolic patients, as they often also suffer from hepatic steatosis. This notion highlights the importance of understanding the molecular regulation of VLDL biogenesis. Fortunately, there has been a resurgence of interest in the intracellular assembly, trafficking, degradation, and secretion of VLDL by hepatocytes, that has led to many exciting new molecular insights, the topic of this review. We think that increasing our understanding of the biology of this pathway will help improve the health of the cardiometabolic patient in the long term.

Two modal decomposition techniques, including proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD), are used to identify the wake patterns past single and two crossing cylinders in 60° and 90° arrangements with gap ratio G = 4. The flow is simulated using direct numerical simulations (DNS) for Reynolds numbers Re = 100. The spatial scale of flow decreases with increasing modal frequency from the modal analysis. Two main modes are identified in the wake of the cylinders, namely spatially antisymmetric and symmetric modes. Antisymmetric and symmetric modes are related to cylinders’ vortex shedding and shedding vortices’ shift motion, respectively, whose frequencies are odd and even multiples of cylinders’ lift force frequency. In addition, a low-frequency mode concerning the shadowing effect of the downstream cylinder (DC) in 90° arrangement is found in the wake of the DC centre.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

Background: Protein CCDC186 is involved in the maturation of dense core vesicles in the trans-Golgi network in neurons and endocrine cells. To date, only one patient, within a large sequencing study of 1000 cases, and a single case report with variants in CCDC186 had previously been described. However, no functional studies in any of these two cases had been performed. Methods: Exome sequencing from one affected individual of each family was performed. In addition, Sanger sequencing of the parents and one of the affected siblings was also performed. CCDC186 protein was assessed in cultured fibroblasts or muscle tissue by western blot. Transcriptomic analysis was done by means of RNA sequencing. Results. We identified three patients from two gypsy families, unrelated to each other, with the same homozygous mutations in CCDC186 gene. Clinically, all patients presented with seizures, frontotemporal atrophy, hypomyelination, recurrent infections, and endocrine disturbances such as severe non ketotic hypoglycemia. Low levels of cortisol, insulin or growth hormone could only be verified in one patient. All of them had a neonatal onset and died between 7 months and 4 years of age. WES identified a homozygous variant in CCDC186 gene (c.2215C>T, p.Arg739Ter) in the index patients of both families. Protein expression studies demonstrated that the CCDC186 was practically undetectable in fibroblasts and muscle tissue. These observations correlated perfectly with the transcriptomic analysis performed in fibroblasts in one of the patients, which showed a significant reduction of CCDC186 mRNA levels. Conclusion. Our study provides functional evidence that mutations in this gene have a pathogenic effect on the protein and reinforces CCDC186 as a new disease-associated gene. In addition, mutations in CCDC186 could explain the combined endocrine and neurologic alterations detected in our patients

This paper aims at trying to answer the question of whether a low cost drone equipped with a regular camera can serve as a simple device to estimate the size of objects. Ad-ditionally, it assesses if the accuracy of measurement is good enough for using a drone for measurements, relying solely on GPS position and camera. A review of the literature pertaining to ground object measurements was conducted. The availability of such in-struments was evaluated in terms of purchase and rental costs, the number of instru-ments on the market, and the time to obtain them. The most common measurement methods were considered and their unit costs were reviewed. The cost of professional surveying and measuring equipment was compared to the possibility of using low-cost, non-commercial drones to measure objects and surfaces. The quality of the images ob-tained was compared with high-resolution satellite systems. Is an ordinary drone with a standard camera suitable for length measurement without professional measuring equipment? Should the results be considered only in the category of size estimation?

One of the key issues in sustainable tourism research is the gap between tourists' expressed friendly attitudes towards sustainable behaviors and their actual behaviors. Although many "low-carbon" themed restaurants have emerged during the low-carbon transformation of the Chinese tourism industry, low-carbon food services have not been significantly improved. This study takes food as the entry point to explore tourists' behavior and attitudes towards low-carbon tourism in relation to food. We conducted two interviews. The first interview was a semi-structured contextual interview with 120 tourists who had experiences in food streets, aim-ing to identify the core user group: low-carbon attitude-friendly tourists with high-carbon food behaviors. The second interviews was an in-depth interview based on grounded theory with 29 core users, analyzing the four main reasons for their high-carbon food behaviors and their re-quirements for low-carbon food services in tourism. Based on this, we extracted four design ele-ments for low-carbon tourism food services: low-carbon information show service, low-carbon service product attractiveness improvement, low-carbon food environment atmosphere creation, and service providers' low-carbon behaviors. Through these four service elements, we constructed a low-carbon tourism food service design framework based on the core users' needs, discussed the mechanism of service elements, and provided service design suggestions accordingly. The re-search results serve tourism providers, low-carbon tourism researchers, and designers.

Chronic pain is a serious health concern and potentially debilitating condition, leading to anxiety, depression, reduced productivity and functionality, and poor quality of life. This condition can be even more detrimental and incapacitating in the pediatric patient population. In low and middle income countries (LMICs), pain services are inadequate or unavailable, leaving most of the world's pediatric population with chronic pain untreated. Many of these children in LMICs are suffering without treatment, and often die in pain. Awareness and advocacy for this population must be prioritized. We reviewed the available literature on the chronic pediatric pain burden in LMICs, barriers to treatments, and current efforts to treat these patients.

Face recognition is a key computer vision task that focuses on identifying or verifying individuals using their facial features. This task becomes more difficult with low-resolution images, where the reduced pixel count and detail make it harder to extract and match features accurately. In this study, we assess the effectiveness of Multilinear Side-Information-based Discriminant Analysis (MSIDA) on low-resolution images, using the CelebA database as a reference. The system showed strong performance, achieving 90.60% accuracy on high-resolution and 88.23% on low-resolution images, highlighting the robustness and effectiveness of MSIDA.

Hamstring muscle (HM) flexibility is frequently compromised in people with chronic low back pain (CLBP), contributing to disability and leading to a less favorable recovery. In a previous article, we presented the results of a study on the immediate effect of passive HM stretching on flexibility in 90 people with CLBP. There was considerable variability in the changes after stretching. The objective of this supplementary analysis was to compare the clinical characteristics of individuals who experienced a significant improvement in flexibility with those who did not. We fixed a threshold of 7° to indicate an improvement in passive Straight Leg Raise (SLR) angle and differentiate between 'Responders' and 'Non-responders' to passive HM stretching. Only Body Mass Index differed between groups; it was significantly smaller in Responders (p=0.007). The majority of Non-responders experienced workplace accidents, but this was of marginal difference compared to Responders (p=0.056). Further studies should consider a broader clinical analysis with a larger sample size to understand which factors influence the HM stretching response in CLBP patients.

Iron supplementation is associated with side effects and thus reduces the intake compliance. Because it has fewer side effects, a recent trial recommended low-iron micronutrient powder (MNP) for the prevention of anemia in Bangladeshi children exposed to a high concentration of iron from drinking groundwater. In the present study, we hypothesize that the low-iron MNP is a potential intervention to prevent childhood anemia in the low groundwater-iron settings in Bangladesh. A cross-sectional study was conducted in Bangladesh with children aged 2-5 years who drank groundwater containing a low level of iron (0-&lt;2 mg/L).The combined intake of iron was calculated from the key sources--diet, groundwater and MNPs. The intakes of iron were compared against the standard reference intake. The children’s hemoglobin was measured using a photometer. Combined intake of iron from dietary, groundwater and low-iron MNP in children was 5.8±2.0 and 6.9±2.5 mg/day comprising 193% and 169% of the Estimated Average Requirement in the 2-3 year-old and 4-5 year-old subgroups, respectively. Combined intake of bioavailable iron from dietary and groundwater sources was 0.42±0.023 and 0.22±0.019 mg/day in children exposed to groundwater concentration 0.8-&lt;2.0 mg/L and 0.0-&lt;0.8 mg/L respectively (p&lt;0.001). The mean concentration of hemoglobin in the respective groups was 12.17±0.94 mg/dl and 11.91±0.91 mg/dl (p=0.30). The combined intake of iron from dietary and groundwater sources was associated with maintenance of hemoglobin concentration at the non-anemic level in most of the children. The finding highlights the potential of low-iron MNP in controlling childhood anemia in this setting.

Uncertainties in initial water saturation and early water breakthroughs of un-known sources and paths, which occurred in the low resistivity Lower Haushi sand-stone (LHS) reservoir at the beginning of oil production, imply that the bypassed oil can yet remain in the reservoir. In addition, the upper part of LHS is a tight oil reser-voir, which can still contain a significant amount of unrecovered oil. This opens the opportunity to produce the remaining oil instead of abandoning this reservoir. Low resistivity can exaggerate water saturation, leading to misinterpretation and premature water flooding due to inadequate oil-water contrast. Our analysis revealed a correlation between low resistivity and robust porous network connectivity, along-side elevated formation water salinity in highly porous layers. In regions of high po-rosity, sufficient oil-water contrast facilitates precise water saturation determination, affirming oil presence in all wells. However, within tight oil zones, near-complete wa-ter saturation contradicts actual oil presence. Factors contributing to saturation un-certainty and water breakthroughs were reassessed. Utilizing a 1:1 verti-cal-to-horizontal permeability ratio derived from core data enhanced simulation alignment with water production rates. Investigation into the impact of relative per-meabilities on water production was conducted. Water saturation maps were gener-ated to pinpoint remaining oil reserves. Depletion around wells is evident in lower po-rous regions, while oil persists across the entire tight reservoir, notably in two unex-plored sections.

Several Lung diseases can result in lung damage structural changes, with lung transplantation as a only therapeutic option when the disease reaches an advanced progression, unfortunately, the success of lung transplantation is limited. In this context, lung bioengineering is considered a potential therapeutic alternative and the current approach is based on the use of the natural extracellular matrix (ECM) of the decellularized lung. The use of undifferentiated cells to seed an ECM can be a more practical strategy for lung bioengineering but the sterilization of the organ for this recellularization process is still a challenge. In this sense, Low-Level Laser Therapy (LLLT) can emerge as a potential treatment alternative. Therefore, the objective of this study was to verify if LLLT, can optimize lung recelularization with mesenchymal stem cells by cytokine modulation. For this, we decellularized lungs from C57BL/6 mice perfusing SDS 1% via pulmonary artery, sterilized with LLL (660nm, 100mW, 30s). Whole lung scaffolds were recellularized: (1) Recellularized Lung (2) Recellularized Lung + LLLT. Mesenchymal stem cells derived from human tooth pulp (DPSc) were seeded into lungs and incubated for 24 hours at 37ºC, 5% CO₂, in a bioreactor-like conditions, maintaining CPAP at 20cmH2O, 90% O2, and LLL at wavelength of 808nm, 100mW, 30s. Culture medium were analyzed at 24 hours. H&amp;E, immunostaining, SEM and ELISA assay were performed. We produced viable biological scaffolds absent of DNA content, preserving glycosaminoglycans and collagen I, III and IV, fibronectin, laminin and elastin and lung structure (SEM). The levels of IL-6 and IL-8 were stable during the 24 hours of culture. IFN-γ levels showed significant difference in the DPSc and DPSc+LLLT group in the 24-hour evaluation. The levels of IL-10 decreased after LLLT. These findings highlight LLLT's role in cytokine regulation and contamination prevention during lung recellularization with mesenchymal stem cells. Overall, these results demonstrated that LLLT's modulated cytokine levels and could prevent contamination during the lung recellularization process with mesenchymal stem cells, offering promise for enhanced therapeutic strategies in lung bioengineering.

To investigate the structural behavior of simply supported concrete beams with steel and polypropylene fiber under low velocity impact loading. In all twenty-four beams (150X200X1800 mm) with simply supported boundary condition were modeled and analyzed using ABAQUS software. Steel and polypropylene fibers of aspect ratio of 60 and 231 respectively are used. The total volumes of fibers are maintained at 1% by volume of specimen. A 100 kg hammer with tip diameter 16 mm (hemispherical contact area = 201 mm2) with four different velocities (3.13 m/s, 4.42 m/s, 5.43 m/s and 6.11 m/s) were used in the analysis. It is observed that with the addition of hybrid fibers the deflection in beams was reduced. The beams with 1% PP and 0% steel fiber shows the maximum deflection values due to low modulus of elasticity. Beams with 0.9% steel and 0.1% polypropylene fibers was less affected in terms of deflection as compared to all other beams, it is due to presence of high tensile strength fibers.

Phenylketonuria is an inherited metabolic disorder that leads to neurobehavioral dysfunction. The main treatment is a low-phenylalanine diet and/or the cofactor tetrahydrobiopterin. Regular outpatient follow-up care and measurement of the phenylalanine level in the blood are required. We aimed to analyze the economic burden of phenylketonuria on families and the state. The pa-tients with phenylketonuria were divided into three groups according to their treatment: a low-phenylalanine diet group (n= 50), a tetrahydrobiopterin group (n= 44) and a group taking tetra-hydrobiopterin together with the diet (n= 25). A comparative cost analysis was carried out. The annual economic burden to the state was calculated to average €18801±15345 and was lowest in the diet group, then in the tetrahydrobiopterin group and highest in the tetrahydrobiopterin+diet group (p < 0.001). Out-of-pocket costs amounted to €1531±1173 per year, and indirect losses aver-aged €2125±1930 per year for all families. The economic loss was significantly lower in the fami-lies taking tetrahydrobiopterin than in the other groups (p=0.001). The combined use of medical nutrition and BH4 treatments has been shown to increase the economic harm to the state. Reim-bursing low-protein products and increasing the rate of patients eligible for financial allowances may reduce the economic harm to families.

The low-altitude quasi-periodic (LQP) E-region echoes observed with the upgraded HCOPAR located in Hainan Island of China (19.5°N, 109.1°E) are presented. With the interferometry technique, the interferometry equations can be developed to investigate the structures of the irregularities. The results show that the plasma structures of the LQP echoes with negative slope mainly drift southwestward almost horizontally, but they also drifted southeastward in some striations. According to the movement of the plasma structures, we find strong wind shear in the region where the LQP echoes are produced. Meanwhile, The periodicity of the LQP echoes may be related to the strength of the wind shear. It is proposed that the plasma structures are most likely produced by the Kelvin-Helmholtz instability.

Glucose is an important carbon sources for microbial growth, and its content in infertile soils is essential for the growth of the bacterium. Since the mechanism of oligotrophic bacterium adaptation in barren soils is unclear, the research employed RNA Seq technology to examine the impact of glucose concentration on the low nutrient bacteria BS-G1 in soil affected by desertification. RNA-Seq revealed that differentially expressed genes（DEG）histidine metabolism, glutamate synthesis, HIF-1 signalling pathway, sporulation, and TCA cycle pathway of BS-G1 were significantly enriched in 0.015 g/L glucose concentration, compared with 10 g/L glucose concentration. DEG amino acids system, two-component system, Metal Ion Transport, and nitrogen metabolism system of B. subtilis BS-G1 were significantly enriched in 5 g/L glucose concentration, compared with 10 g/L glucose concentration. In addition, The present study identified its regulation pattern and key genes under the low glucose environment (7 mRNAs, 16 sRNAs). This study primarily investigates the variances in the regulatory pathways of oligotrophic bacteria BS-G1, which holds substantial importance in comprehending the mechanism underlying the limited sugar tolerance of oligotrophic bacteria.

Regulatory monitoring networks are often too sparse to support community-scale PM2.5 exposure assessment while emerging low-cost sensors have the potential to fill in the gaps. Recent advances in air quality monitoring have produced portable, easy-to use, low-cost, sensor-based monitors, which has given a new dimension to the air pollutant monitoring and has democratized the air quality monitoring process by making monitors and results directly available at community level. This study used PurpleAir(c) sensors for PM2.5 assessment in California, USA. Evaluation of PM2.5 from sensors included Quality Assurance &amp; Quality Control (QAQC) procedures, assessment with respect to reference monitored PM2.5 concentrations, and formulation of a decision support system integrating these observations using geostatistical techniques. The hourly and daily average observed PM2.5 concentrations from PurpleAir monitors followed the trends of observed PM2.5 at regulatory monitors. PurpleAir monitored PM2.5 also captured the peak PM2.5 concentrations due to incidents like forest fire. In comparison with reference monitored PM2.5 levels, it was found that PurpleAir PM2.5 concentrations were mostly higher. The most important reason for PurpleAir higher PM2.5 concentrations was the inclusion of moisture or water vapor as aerosol in contrast to measurements of PM2.5 excluding water content in FEM/FRM and non-FEM/FRM monitors. On long term assessment (2016-2020), R2 was between 0.54 and 0.86 at selected collocated PurpleAir and regulatory monitors for hourly PM2.5 concentrations. Past research studies have been conducted for mostly shorter time periods (&lt;3-4 months) that resulted in higher R2 values between 0.80 to 0.98. This study aims to provide reasonable estimations of PM2.5 concentrations with high spatiotemporal resolutions based on statistical models using PurpleAir measurements. The methods of Kriging and IDW, geostatistical interpolation techniques, showed similar spatio-temporal patterns. Overall, this study revealed that low-cost, sensor based PurpleAir sensors could be effective and reliable tools for episodic and long-term ambient air quality monitoring.

Most of the fishing currently practiced in Japan is done by small vessels with a small number of fishermen (one or two). One of the most common fishing methods is longline fishing. However, this method requires the vessel to operate at a constant low speed because the depth of the hook must be kept constant while adjusting the speed of the fishing boat to the tidal current. In addition, because the vessel must maneuver and fish at the same time, automation is desired. Thus, we propose a robotic system that can control the depth of the trap at a constant depth even when the speed of the vessel and the current change, and that can successfully fish without the need for skilled fishermen. Fishing can be conducted regardless of the speed of the vessel, whereas currently it is controlled by the speed of the vessel and the tidal current. Therefore, it may contribute to proposing new fishing methods as well as the existing ones. This can contribute to the shortage of successors to the fishing industry and to the revitalization of the fishing industry.

The purpose of this project was to demonstrate the potential of converting an existing internal combustion engine for hydrogen operation at relatively low cost and to optimize the combustion process for ultra-low NOx emissions. The conversion has been carried out on a 450cc naturally aspirated single cylinder engine. The first baseline measurements and setup have shown lower NOx emissions than the baseline gasoline engine (without catalytic converter) for similar power output and engine efficiency. Further optimization of the combustion process allowed to achieve Euro VI and (latest European Commission proposal) Euro VII heavy-duty NOx limits without exhaust gas aftertreatment system (EATS) in steady state conditions. The concept is very promising and the knowledge gained should allow for further optimization to achieve near zero NOx emissions at high engine efficiency and power output with supercharging. It should also allow an efficient conversion of other engine types for different applications. In particular, a project with the aim to convert a heavy duty 6 cylinder engine intended for public transport buses has started. It follows a feasibility study which has shown the competitiveness of the hydrogen engine for this application.

The paper explores the potential of a low-cost advanced video-based technique for the assessment of structural damage induced to buildings by seismic loading. A low-cost high-speed video camera was utilized for motion magnification (MM) processing of footages of a two-story reinforced concrete frame building subjected to shaking table tests. The damage after seismic loading was estimated by analyzing the dynamic behavior (i.e. in terms of modal parameters) and the structural deformations of the building in the MM videos. The results by MM were compared for method validation to damage assessment obtained by the analyses of conventional accelerometers and high-precision optical markers tracked by a passive 3D motion capture system. Also, 3D laser scanning to obtain an accurate survey of the building geometry before and after the seismic tests was carried out. In particular, accelerometers were also processed and analyzed by using several stationary and non-stationary techniques with the aim to analyze the linear behavior of the undamaged structure and the nonlinear structural behavior during damaging shaking table tests. The proposed MM-based procedure provided accurate estimate of the main modal frequency and the damage location through the analysis of modal shapes, which were confirmed by advanced analyses of accelerometric data.

In this study, we explore the potential of using a straightforward neural network inspired by the retina model to efficiently restore low-light images. The retina model imitates the neurophysiological principles and dynamics of various optical neurons. Our proposed neural network model reduces the computational overhead compared to traditional signal-processing models while achieving results similar to complex deep learning models from a subjective perceptual perspective. By directly simulating retinal neuron functionalities with neural networks, we not only avoid manual parameter optimization but also lay the groundwork for constructing artificial versions of specific neurobiological organizations.

The goal of classroom English instruction is to educate students on how to use the English language effectively for communication in any scenario. It is identified by presenting various teaching tactics and speaking activities to encourage students to participate more actively in conversations. The study intended to identify the problems in the speaking performance of Grade 8 Jade in Tagum City National High School. The study was conducted using a quantitative non-experimental descriptive survey method. Results revealed that the problems in speaking performance have garnered a mean of 3.20 (moderate) as descriptive equivalent and it was found out that the prevailing speaking problem is anxiety with a mean of 3.84, interpreted as high. Thus, an intervention program is designed to address the problems in the speaking performance of the respondents. This program is divided into two: Overcoming Speaking Anxiety Seminar-Workshop and Speaking Enhancement Activities.

Low back pain is a common problem in the active population, and the second reason for visiting a physician. In patients with lumbar disc protrusion, the nucleus pulposus bulges against the disc and the latter protrudes into the spinal column, but the annulus fibrosus remains intact. The purpose of this study was to prove that starting an early complex rehabilitation treatment results into pain and disability reduction, and increased muscle strength and mobility in patients with lumbar disc protrusions. We performed a prospective cohort study, enrolling 60 patients (25 men and 35 women) aged between 26 to 76 years, diagnosed with lumbar disc protrusion. Patients in the experimental group registered significant improvements in all studied variables (pain, mobility, muscle strength, disability) after 6 months of treatment. The results of our study suggest that, in the lumbar disc disease, a combined rehabilitation program may be more effective in terms of pain and disability reduction, if it starts early after diagnosis. The current study proves the importance of combining electrotherapy with hydrotherapy and physical therapy. Patients who received this treatment combination showed an extremely significant improvement in pain relief, and reduction of functional disability after 6 months of treatment.

Pepper plants experience complex environmental factors including abiotic and biotic stresses in field and the importance of climate changes including low and high temperatures has been emerged. Low temperature stress in the growth and development is one of the most critical issues, which directly impact on the crop yield and productivity of pepper plants. It is essential to select and breed low temperature-(LT) tolerant pepper (Capsicum annuum L.) cultivars. The research was performed to assess the agronomical traits of 39 pepper accessions belonging to chili and bell fruit types which cultivated two different night temperature set-points at 15°C for suboptimal temperature (CT) and at 10°C for low temperature (LT), respectively. Plant heights (PH) of most pepper accessions in LT were significantly decreased compared to those in CT. The stem diameter (SD) and the length of main axis (LMA) were various depending on the genotypes under LT. Moreover, the number of flowers (NFL), the total number of fruits (NFR), fruit yield (FY), fruit fresh weight (FFW), fruit length (FL), fruit diameter (FD), and the number of seeds in a fruit (NSF) were notably declined in LT compared to CT. The evaluated agronomical traits between LT and CT were further applied for the correlation analysis, the principal component analysis (PCA), and the hierarchical cluster analysis. Notably, FY trait was correlated with other reproductive traits including NFR, FFW, FD, and FL on positive directions and LT treated-39 pepper accessions were clustered into seven groups by the clustering analysis. The selected accessions were primarily involved with the positive trends with the reproductive index including NFR, FL, FD, and FW traits and would be used for pepper breeding programs on developing LT-tolerant cultivars.

(1) Background: Although manual therapy for pain relief has been used as an adjunct in treatments for chronic low back pain (CLBP), there is still the belief that a single session of myofascial release would be effective. This study aimed to investigate whether a single session of a specific technique reduces pain and disability. (2) Methods: This was a crossover clinical trial in which 41 participants over 18 years old with CLBP were randomly enrolled into 3 situations - experimental, placebo, control, in a balanced and cross-over manner. The subjects underwent a single session of myofascial release on thoracolumbar fascia and compare it with the control and placebo. Outcome were pain and functionality, evaluated using the numerical pain rating scale (NPRS), pressure pain threshold (PPT) and Oswestry (ODI). (3) Results: There was no effects between-, within-tests, and interaction for all the outcomes, i.e., NPRS (η 2 = 0.32, F = 0.48, p = 0.61), PPT (η2 = 0.73, F = 2.80, p = 0.06), ODI (η 2 = 0.02, F = 0.02, p = 0.97). (4) Conclusion: A single trial of thoracolumbar myofascial release technique was not enough to reduce pain and disability in subjects with CLBP.

Background: To examine the association between income levels and mortality rates in patients with chronic kidney disease. Methods: We analyzed data obtained from 3,172 patients with chronic kidney disease obtained from the Korean National Health Insurance claims database (2003–2009). Each patient was monitored until December 2010 or until death, whichever came first. Individual income was estimated from the national health insurance premium. Information on mortality was obtained from the Korean National Statistical Office. Cox proportional hazard models were used to compare mortality rates between different income groups after adjusting for possible confounding risk factors. Results: A low income was significantly associated with a high mortality rate after adjusting for covariates (adjusted HR 1.298 [1.082–1.556]). In addition, dialysis patients who had low incomes were more likely to have higher mortality rates compared to those in dialysis patients who had high incomes (adjusted HR 1.528 [1.122–2.082]). Conclusion: The findings of this study indicate that chronic kidney disease patients with low incomes have the highest mortality risk. Promotion of targeted policies and priority health services for patients with low incomes may help reduce the mortality rate in this vulnerable group.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

The establishment of low carbon assessment initiatives is a crucial task especially at the city level. The determination of which source of carbon contributed more require robust data set and strategic approach. Hence, by using the campus as a small city approach, the establishment of carbon assessment and its’ reduction initiatives was required to keep track of the hotspot of the carbon source. The substantial amount of carbon source from campus operations such as energy consumption in the building, waste generation, and water consumption were identified. Moreover, as institutions of higher education, the execution of low carbon campus was initiated structurally involves the triangulation of research activities, teaching & learning and as well as campus operations or known as campus living lab approach. The application of low carbon cities framework, LCCF and assessment system enables to strategize the low carbon campus initiatives through the use of carbon footprint concept and the LCCF carbon track.

This paper deals with a non-contact method to identify the aerodynamic propeller parameters of the Parrot AR.Drone quadrotor. The experimental set consists in a camera recording the vehicle flights, the audio signal is extracted and is used a spectrogram analysis to estimates the propeller velocity. First, the aerial vehicle takes off and starts a hovering maneuver. The experiment is repeated with different additional masses attached to its rigid body. If the weight over the UAV increases/decreases, then the propeller must rotates faster/slower to produce a higher/lower thrust, and consequently, the sound frequency increases/decreases. Finally, this proposition is validated experimentally, and the estimated velocity is used to identify the quadrotor thrust parameters.

Introduction: We investigated the potential effect of smoking on pathological staging in clinically low-risk patients. Material-Methods: Data of 59 patients who were diagnosed with a bladder tumor for the first time and had a single lesion radiologically and endoscopically smaller than 3 cm were investigated, retrospectively. A total of 33 patients who currently smoke or smoked were classified as ever smokers group and 26 patients who did not ever smoke were classified as never smokers group. Pathological diagnoses of the patients in both groups were compared. Results: A total of 9 patients (27.3%) in ever smokers group and 18 patients (69.2%) in never smokers group had Ta disease (p<0.05). Morover, 19 patients (57.6%) in ever smokers group and 5 patients (19.2%) in never smokers group had T1 disease (p<0.05). The number of patients with low grade (LG) tumor were 8 (24.2%) and 19 (73.1%) in ever smoking and never smoking groups, respectively (p<0.05). The number of patients with high grade (HG) tumor were 25 (75.8%) and 7 (26.9%) in ever smoking and never smoking groups, respectively (p<0.05). Ta HG was detected in 9 (27.3%) patients in ever smoking group. In contrast, no patients in never smoking group had Ta HG disease (p<0.05). The number of patients with T1 HG was 17 (51.5%) in ever smoking group and 2 (7.69%) in never smoking group (p<0.05). Conclusion:Smoking seems to associate with pathologically worse stage and grade in patients with primary, single, < 3cm bladder cancer.

AbstractWe investigated the effect of cigarette smoking on pathological staging in clinically low-risk patients. Data of 59 patients who were diagnosed with bladder tumor for the first time and had a single lesion radiologically and endoscopically smaller than 3 cm were investigated retrospectively. 33 patients who smoked were classified as Group I, and 26 patients who did not smoke were classified as Group II. Pathological diagnoses of the patients in both groups were compared. The mean age of the patients were 64.8 (20–86) years. In Group II, 5 (19.2%) were female and 21 (80.8%) were male (p < 0.05). Nine patients (27.3%) in Group I and 18 patients (69.2%) in Group II had Ta disease (p < 0.05). Nineteen patients (57.6%) in Group I and 5 patients (19.2%) in Group II had T₁ disease (p < 0.05). The number of patients with low grade (LG) tumor were 8 (24.2%) and 19 (73.1%) in Group I and in Group II, respectively (p < 0.05). The number of patients with high grade(HG) tumor were 25 (75.8%) and 7 (26.9%) in Group I and in Group II, respectively (p < 0.05). TaHG was detected in 9 (27.3%) patients in Group I. In contrast, no patients in Group II had TaHG disease (p < 0.05). The number of patients with T₁HG was 17(51.5%) patients in Group I and 2 (7.69%) patients in Group II (p < 0.05). Smoking is associated with pathologically HG and stage in patients with first time bladder tumor which is single and smaller than 3 cm.

Background: The prevalence of atopic dermatitis in domestic animals is one of the problems of modern veterinary. Treating with standard techniques using chemotherapeutic agents not always leads to a positive result of therapy; moreover, many drugs produce adverse side effects. Methods: Low level laser therapy, in particular, intravenous laser blood illumination (ILBI) has a pronounced and long-lasting impact on the immune system of animals. The combined technique including ILBI-635 (635 nm, 2 mW, 5 min) and LUVBI^® (365 nm, 2 mW, 3 min) every other day provides a positive change in clinical status of cats with allergic dermatitis after the 3rd-4th treatment session. Results: The increased level of erythrocytes and hemoglobin was identified in the course of treatment, and it indirectly indicates increased blood transport activity, which improves trophic provision and microcirculation. A double reduction of leukocytes and a significant decrease of neutrophil cells indicate the immunomodulatory effect of LILI (low-intensity laser illumination). The increase in the percentage of lymphocytes and the decrease of eosinophils and monocytes against the background of basophil concentrations deviations within physiological concentration result in the reduction of inflammatory mediators expression that induce itching. The reduction of total IgE concentration 32 times against control on the 7th day of treatment correlates with the decrease in the quantitative content of peripheral blood eosinophils, indicating the decrease in severity of an allergic process. Conclusion: LLLT is recommended against the background of standard drug therapy to achieve quick clinical outcome together with a long-lasting prolonged effect.

Globally, the transport sector is a major contributor to air pollution. Currently in the UK, vehicle emissions contribute significant amounts of nitrogen oxide (NOx) and particulate matter (PM) pollution in urban areas. Low-emission zones policies have been used as an intervention to tackle air pollution, and in this context, the UK launched the Low- Traffic Neighbourhood scheme. This study investigates the impacts of the Low- Traffic Neighbourhood in Kings Heath, Birmingham, UK, to evaluate its impact in reducing air pollution and local community perspectives about the scheme and perceived impacts on health and well-being. The study employs a mixed-method ap-proach comprising air quality monitoring assessment and a survey questionnaire involving 210 residents. The findings reveal an increase in active travel and a reduction in air pollution levels in the years after the implementation of the scheme, although the area is still non-compliant with the 2021 WHO air quality guidelines. Nonetheless, the scheme has a polarizing effect and created a division within the local community about the overall scheme acceptance and spatial distribution of the scheme’s benefits. The study underscores the importance of comprehensive baseline data, long-term community engagement, and integration with broader urban planning initiatives to enhance the success of future Low-Neighbourhood Traffic schemes.

Hyper-radiosensitivity (HRS) is the increased sensitivity to low doses of ionizing radiation observed in most cell lines. We previously demonstrated that HRS is permanently abolished in cells irradiated at a low dose rate (LDR), in a mechanism dependent on transforming growth factor β3 (TGF-β3). In this study, we aimed to elucidate the activation and receptor binding of TGF-β3 in this mechanism. T-47D cells were pre-treated with inhibitors of potential receptors and activators of TGF-β3, along with addition of small extracellular vesicles (sEVs) from LDR primed cells, before their radiosensitivity was assessed by the clonogenic assay. The protein content of sEVs from LDR primed cells was analyzed with mass spectrometry. Our results show that sEVs contain TGF-β3 regardless of priming status, but only sEVs from LDR primed cells remove HRS in reporter cells. Inhibition of the matrix metalloproteinase (MMP) family prevents removal of HRS, suggesting an MMP-dependent activation of TGF-β3 in the LDR primed cells. We demonstrate a functional interaction between TGF-β3 and activin receptor like kinase 1 (ALK1), by showing that TGF-β3 removes HRS through ALK1 binding, independent of ALK5 and TGF-βRII. These results are an important contribution to a more comprehensive understanding of the mechanism behind TGF-β3 mediated removal of HRS.

Plants frequently encounter relatively low and fluctuating potassium (K+) concentrations in soil, with roots serving as the primary responders to this stress. Histone modifications, such as de-/acetylation, can function as epigenetic marks on stress-inducible genes. However, the signaling network between histone modifications and the low K+ (LK) response pathways remains unclear. This study delves into the regulatory role of Histone Deacetylase Complex 1 (HDC1) in primary root growth of Arabidopsis thaliana under K+ deficiency stress. Using a hdc1-2 mutant line, we observed that HDC1 positively regulates root growth under LK conditions. Compared to wild-type (WT) plants, the hdc1-2 mutant exhibited significantly inhibited primary root growth under LK conditions, whereas HDC1-overexpression lines displayed opposite phenotypes. No significant difference was observed under HK conditions. Further analysis revealed that the inhibition of hdc1-2 on root growth was due to reduced meristem cell proliferation rather than cell elongation. Notably, the root growth of hdc1-2 shows reduced sensitivity compared to WT after auxin treatment under LK conditions. HDC1 may regulate root growth by affecting auxin polar transport and subsequently auxin sensation, as evidenced by altered expression of auxin transport genes. Moreover, our study reveals a brake function of HDC1 in the regulation of CBL-CIPK-K+ channel related genes, thereby establishing a molecular link between histone deacetylation, auxin signaling, and CBL-CIPK pathway in response to K+ deficiency.

Excess sedentary behaviour (SB) and insufficient physical activity (PA) have been identified as risk factors for cardiometabolic diseases in adolescents, some factors may affect how much time they spent on these activities. This study sought to compare the SB and PA patterns as well as the compliance with PA recommendations by sex, geographical location, and time of the week in Mexican adolescents. In a cross-sectional design, we objectively assessed SB and PA in 106 adolescents (15 to 18 y) through waist-worn accelerometers for one week. The time spent in SB and in PA at different intensities was compared by sex, geographical location and time of the week with two-way and three-way repeated measures MANOVAs, while the compliance with physical activity recommendations (i.e. ≥60 min/day) was compared using chi-squared and McNemar tests. Male participants spent more time in moderate, vigorous, and moderate to vigorous PA than females both in the whole week and in weekdays (all p < 0.05). There was no significant difference in SB nor PA by geographical location (i.e., metropolitan vs non-metropolitan areas). Moreover, all participants spent more time on moderate, vigorous, and moderate to vigorous PA on weekdays than on weekends (p < 0.05). Compliance with international PA recommendations also showed a sex difference (males > females) and change between weekdays and weekends with no difference by geographical location. While geographical location does not seem to be a relevant factor, sex and time of the week appear to influence the SB and PA patterns in Mexican adolescents.

Following the detection of highly pathogenic avian influenza (HPAI) virus in countries bordering Kenya to the west, we conducted surveillance among domestic and wild birds along the shores of Lake Victoria. In addition, between 2018 and 2020, we conducted surveillance among poultry and poultry workers in live bird markets and among wild migratory birds in various lakes that are resting sites during migration to assess introduction and circulation of avian influenza viruses in these populations. We tested 7,464 specimens (oropharyngeal and cloacal swabs) from poultry and 6,531 fresh fecal specimens from wild birds for influenza A viruses by real-time RT-PCR. Influenza was detected in 3.9% (n=292) of specimens collected from poultry and 0.2% (n=10) of fecal specimens from wild birds. On hemagglutinin subtyping, most of the influenza A positives from poultry (274/292, 93.8%) were H9. Of 34 H9 specimens randomly selected for further subtyping, all were H9N2. On phylogenetic analysis, these viruses were genetically similar to other H9 viruses detected in East Africa. Only two of the ten influenza A positive specimens from the wild bird fecal specimens were successfully subtyped; sequencing analysis of one specimen collected in 2018 was identified as low pathogenicity avian influenza H5N2 virus of the Eurasian lineage and the second specimen, collected in 2020, was subtyped as H11. A total of 18 OP/NS swabs from poultry workers with ARI (12%) were collected; none were positive for influenza A virus. We observed significant circulation of H9N2 influenza viruses in poultry in live bird markets in Kenya. During the same period, low pathogenic H5N2 virus was detected in a fecal specimen collected in a site hosting a variety of migratory and resident birds. Although HPAI H5N8 was not detected in this survey, these results highlight the potential for introduction and establishment of highly pathogenic avian influenza viruses in poultry populations and the associated risk of spillover to human populations.

Frequently Asked Questions (FAQs) systems rely on semantic symmetry similarity measuring between two sentences. To address the challenges of insufficient training data and limited domain-specific understanding in low-resource FAQs, this paper proposes a general framework, PDAMF-FAQ, to solve these issues. Firstly, we propose a paraphrasing-based data augmentation model that integrates syntactic information and edit vectors. Using a rule-based approach, it retrieves template sentences from a corpus and masks relevant words with special characters. Edit vectors between the original and paraphrase sentences are added to a pre-trained model's encoding layer to enhance the model's ability to learn the differences between the original and reference paraphrase sentences. Additionally, this paper presents a mixed-feature semantic matching model based on SimBERT. The model extracts keyword features from the text, replacing these keywords with special characters to construct intent features. These intent features, along with the user question and keyword features, are then concatenated to form the model's input. Experiments were conducted respectively on the paraphrasing-based data augmentation model, mixed-feature semantic matching model and their comprehensive application in a low-resource domain-specific FAQ. The experimental results show that the proposed framework effectively improve the performance of domain-specific FAQ system.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.