The ductile behavior of strain hardening cement-based composites (SHCC) under direct tensile load makes them promising solutions for applications where high energy dissipation is needed, such as earthquake, impact by a projectile, or blast. However, the superior tensile ductility of SHCC due to multiple cracking does not necessarily entail compressive and shear ductility. As an effort to characterize the behavior of SHCC under impact compressive and shear loading, relevant to the mentioned high-speed loading scenarios, the paper at hand studies the performance of a SHCC and its constituent cement-based matrices using the split-Hopkinson bar method. For compression experiments, cylindrical specimens with a length-to-diameter ratio (l/d) of 1.6 were used. The selected length of the sample led to similar failure modes under the quasi-static and impact loading conditions, which was necessary for a reliable comparison of the obtained compressive strengths. The impact experiments were performed in a split-Hopkinson pressure bar (SHPB) at a strain rate that reached 110 s-1 at the moment of failure. For shear experiments, a special adapter was developed for a split-Hopkinson tension bar (SHTB). The adapter enabled performing impact shear experiments on planar specimens using the tensile wave generated in the SHTB. Results showed a dynamic increase factor (DIF) of 2.3 and 2.0 for compressive and shear strength of SHCC, respectively. As compared to the non-reinforced constituent matrix, the absolute value of the compressive strength was lower for the SHCC. Contrarily, under shear loading, the SHCC yielded the higher shear strength than the non-reinforced matrix.

COVID-19, previously known as “2019 novel coronavirus”, is a newly discovered virus which causes severe acute respiratory syndrome, similar to corona virus 2 (SARS-CoV-2), which has spread widely through human to human contact and was declared a pandemic by the WHO in March 2020. To cope with this pandemic many countries have adopted nationwide lockdowns which restrict nonessential activities and encourage their populations to avoid public transport, work from hone wherever possible, and to maintain social distancing at all times. While the severity of these shutdowns has varied with country, large geographic regions of the world (including China, India, Iran, Italy, Spain, and the USA) have all been severely affected, not just in the loss of human life, but also in terms of the financial impacts the lockdowns will have on their countries future prosperityIt was previously reported that a number of environmental factors, including humidity and temperature, played an important role in development and spread of the SARS-Corona Virus infection with the virus retaining viability for over 5 days at temperatures between 22–25^oC and relative humidity (RH) of 40–50%. Whereas, elevated temperatures and higher RH (38^oC, and >95% RH) decreased virus viability (Kroumpouzos et al., 2020). The spread of COVID-19 started in low temperature areas of China, with major outbreaks subsequently occurring in Iran, Japan, Northern Italy and South Korea. These new virus epicenters all had similar temperature and latitude, along the 30-50^◦N” zone. Subsequently, the virus was spread to regions of elevated temperature, such as India, the Middle East and Thailand, due to international travel (Kroumpouzos et al., 2020).The aim of this study was to consider the environmental impact of COVID-19, including water pollution. The paper is divided into four sections. In the first section the current literature related to COVID-19 is reviewed. In the second section a recent update on COVID-19 globally is presented, followed by a descriptive impact on the environment in the third section and finally in the fourth section the COVID-19 related worldwide environmental impact is discussed. Since COVID-19 is a currently an active pandemic with no end in sight, while constructive conclusions can only be made on the limited data currently, which may be prone to high errors. However, these conclusions may provide some preliminary suggestions for assisting in assessing spreading patterns of COVID-19 across the globe, and may be of long-term significances with respect to assessing the environmental impact of lockdown policies due to COVID-19 worldwide.

Due to remarkable socioeconomic development, an increasing number of karst rocky desertification areas have been severely affected by human activities in southern China. Effectively analyzing human activities in karst rocky desertification areas is a critical prerequisite for managing and restoring areas with tremendous negative impacts from desertification. At present, a timely and accurate way of quantifying the spatiotemporal variations of human activities in karst rocky desertification areas is still lacking. In this communication, we attempted to quantify human activities from the corrected NPP-VIIRS nighttime light data from 2012 to 2018 based on statistical analysis. The results show that a significant increase of night lights could be clearly identified during the study period. The total nighttime lights (TL) related to severe karst rocky desertification (S) were particularly concentrated in Guizhou and Yunnan. The nighttime light intensity (LI) related to the S areas in Chongqing were the strongest due to its rapid socioeconomic development. The annual growth rate of nighttime lights (GL) has been slow or even negative in Guangdong because of its various karst rocky desertification restoration programs. This communication could provide an effective approach for quantifying human activities and provide useful information about where prompt attention is required for policy-making on the restoration of the karst rocky desertification areas.

Consideration of climate change in Environmental Impact Assessment (EIA) is a rather novel topic, which became partly mandatory through the revised EU Directive on EIA. Through a mixed-methods approach involving key-actors from EIA practice, decision making and climate adaptation planning, this study presents a transdisciplinary point of view on barriers and opportunities to tackle climate change adaptation in environmental assessment of large-scale projects. It is based on both a retrospective ex-post evaluation of existing practices in Austria and Germany as well as prescriptive examination and development of outcomes for practice through the development of a climate-fit toolkit that supports the incorporation of climate change impacts into EIAs. The scenario analysis applied with a back casting approach provided the opportunity to look beyond limitations related to legal compliance and partly lack of data identified by previous research. Three scenario narratives were elaborated based on nine key impact factors based on literature review, content analysis of EIA documents and interviews with EIA actors. The groups of actors carried out a prioritization of actions towards consideration of climate change in EIA. Finally, the actors were involved in co-production of an online tool-kit for Austrian and German EIA practice.

Human-generated, natural occurrences and other actions connected with the petroleum industry have contributed expansively to the contamination of numerous areas of human habitant, thus effecting overwhelming challenges and constraints to sustainable human health, development and the biosphere. The sites commonly associated include derelict pits, hydrocarbon onshore release sites, and places to where oil slicks exuding from offshore releases are blown onshore. In diverse cases, remediation is pertinent to restore the affected ambient. This is required despite the complexity and intricate pore structure and fluid trafficking trajectories of soil which are not easily amenable to remediation. Due to the complex assemblage of contaminated soil, it is necessary to conduct an encompassing site assessment by considering the potential impact of the environment and human health prior to proper selecting and implementing of a desirable remediation process. There are extant remediation methodologies which are effective and efficient for the clean up of contaminated shorelines and other petroleum-contaminated sites involving inter alia agricultural activities. There are salient variations in the techniques to expunge contaminants regarding spatiotemporal and pecuniary costs or considerations due to the gross environmental hazards entailed. This study provides for the opportunity to harness and sustain the capacity for the mitigation of untoward impacts, and induce the latitude for an enabling condition in sustainable human health, environment and development in the petroleum industry and other anthropogenic activities.

In some cases, the human impact on ancient landscapes has been so profound that local soils still remain significantly affected even after hundreds and thousands of years after ending impact. We studied the Late Bronze Age Muradymovo settlement located in Urals, Russia, aiming to estimate the consequences of the ancient people activity for environment. Despite the present humid climate, the modern soils inside the cultural layer of the study site contain more than 27% of gypsum at a depth of just 10 cm from the surface, and a microrelief of the study site is typical of a gypsum desert. The nearby background Chernozems are gypsum-free to a depth of 2 meters. According to the archaeological data, the ancient people belonged to the ‘Srubno-Alakul’ archaeological culture (1750–1350 yrs BC cal) and had a tradition of building their houses from gypsum rocks. At the present time, this area is still unsuitable for human settlement. The properties of modern soils inside the cultural layer of the study site are directly affected by the Late Bronze Age human activities. It has been identified on soil morphology, micromorphology and chemical properties of soils developed inside the cultural layer of the settlement.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

This study aimed to evaluate the relationship between various asbestos exposure routes and asbestos-related disorders (ARDs). The study population comprised 11,186 residents of a metropolitan city who lived near asbestos factories, shipyards, or in slate roof-dense areas. ARDs were defined from chest X-rays indicating lower lung fibrosis (LFF), pleural disease (PD), and lung masses (LMs). Of the subjects, 11.2%, 10.4%, 67.2% and 8.3% were exposed to asbestos via occupational, household, neighborhood, and slate roof routes, respectively. Regarding adjusted confounders and other exposure routes, the odds ratio (OR) of PD from household exposure (i.e., living with asbestos-producing workers) was 1.9 (95% confidence interval: 0.9–4.2), and that of LLF and PD from neighborhood exposure, or residing near asbestos factories) for <19 or >20 years, or near a mine, were 4.1 (2.8–5.8) and 4.8 (3.4–6.7), 8.3 (5.5–12.3) and 8.0 (5.5–11.6), and 4.8 (2.7–8.5) and 9.0 (5.6–14.4), respectively. The ORs of LLF, PD, and LM among those residing in slate-dense areas were 5.5 (3.3–9.0), 8.8 (5.6–13.8), and 20.5 (10.4–40.4), respectively. Substantial proportions of citizens residing in industrialized city have potentially been exposed to asbestos, and various exposure routes are associated with the development of ARDs. Notably, this may be the first finding of the health effects of slate roof exposure. However, given the limitations of this study, including potential confounders such as socioeconomic status, further research is needed.

2.25Cr-1Mo steel with high strength at high temperatures and good hydrogen resistance is widely used for power generation boiler material in high temperature and pressure use environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 285 and 21 ft-lb, which are drastically different values. The analysis of the fracture surface of the 21 ft-lb test specimen revealed MnS inclusions, and it was found that cracks initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 285 ft-lb impact specimen; however, the volume fraction of the inclusions was significantly less than that of the 21 ft-lb specimen. It was also found that the ferrite and carbide content of the 285 ft-lb specimen was less than 21 ft-lb specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation, such as MnS inclusions on ferrite and carbide, were compared and analyzed.

Impact characterization of linear resonant actuator (LRA) is studied experimentally by newly developed drop tester, which can control various experimental uncertainty such as rotational moment, air resistance, secondary impact and so on. The feasibility of this test apparatus was verified by comparison with free fall test. By utilizing a high-speed camera and measuring the vibrational displacement of spring material, the impact behavior was captured and the damping ratio of the system was defined. Based on the above processes, the finite element model was established and the experimental and analytical results were successfully correlated. Finally, the damage of the system from impact loading can be expected by developed model and as a result, this research can improve the impact reliability of LRA.

This research focuses on exploring generalized electron emissions in one-dimensional conducting materials, specifically examining field emission and thermionic emission. Additionally, the study investigates one-dimensional thermal radiation. The current density is derived for both one-dimensional thermionic emission and one-dimensional field emission. A generalized current density in one dimension is devised, taking into account arbitrary accelerating fields and temperature conditions. The formula for the one-dimensional current density is depicted with accelerating field and temperature across various work function materials. The current is also represented as a function of both temperature and electric field for various temperatures.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

A mixture of nonlabeled (14N2H4) and 15N labeled hydrazine (15N2H4) in an aqueous solution is oxidized to 15N2, 14N2, and 14N15N molecules, indicating the intermediate existence of the 14NH2-14NH-15NH-15NH2 with subsequent hydrogen transfers and splitting of side N-N bonds. Structures, thermodynamics, and electron characteristics of various N4H6 molecules in aqueous solutions are investigated using theoretical treatment at the CCSD/cc-pVTZ level of theory to explain the crucial part of the hydrazine oxidation reaction. Most N4H6 structures in aqueous solutions are decomposed during geometry optimization. Splitting the bond between central nitrogen atoms is the most frequent, but the breakaway of the side nitrogen is energetically the most preferred. The N-N fissions are enabled by suitable hydrogen rearrangements. Gibbs free energy data indicate the dominant abundance of NH3... N2... NH3 species. The side N atoms have very high negative charges, which should support hydrogen transfers in aqueous solutions. The only stable cyclo-(NH)4…H2 structure has a too high Gibbs energy and breaks the H2 molecule. The remaining initial cyclic structures are split into hydrazine and HN≡NH or H2N≡N species, and their relative abundance in aqueous solutions is vanishing.

The results of electron-beam processing of Mn-Zn ferrite samples using pulsed and continuous electron beams in the forevacuum pressure range (10 Pa) are presented. We find that continuous electron-beam processing leads to surface structuring of the ferrite, changes in elemental composition on the surface, and electrical property modification. The degree of ferrite parameter changes exhibits a threshold behavior. For surface processing temperatures below 900 °C, changes are barely noticeable, while for temperatures over 1100 °C the surface resistance decreases by more than an order of magnitude. Electron-beam processing with millisecond pulse duration and pulse energy density exceeding 15 J/cm² results in the formation of low zinc content melt islands, while the remaining surface area (outside the islands) elemental content and ferrite properties remain largely unchanged. The thickness of the modified layer depends on the processing mode and can be controlled over the range 0.1–0.5 mm. Because of its low resistance, the modified layer can be utilized to enhance the RF-absorbing properties of the ferrite.

Striated muscle thick filaments are composed of myosin II and several non- myosin proteins which define the filament length and modify its function. Myosin II has a globular N-terminal motor domain comprising its catalytic and actin-binding activities and a long α-helical, coiled-coil tail that forms the dense filament backbone. Myosin alone polymerizes into filaments of irregular length, but striated muscle thick filaments have defined lengths that with the thin filament define the sarcomere structure. The motor domain structure and function are well understood but the myosin filament backbone is not. Here we report a structure of the flight muscle thick filaments from Drosophila melanogaster at 4.7 Å resolution which eliminates previous ambiguities in the non-myosin densities. The full proximal S2 region is resolved as are the connecting densities between the Ig domains of stretchin-klp. The proteins, flightin and myofilin are resolved in sufficient detail to build an atomic model based on an AlphaFold prediction. Our results suggest how flightin and myofilin cooperate to define the structure of the thick filament and explains a key myosin mutation that affects flightin incorporation. Drosophila is a genetic model organism for which our results can define strategies for functional testing.

Recent advancements in the study of the protein complex photosystem II have clarified the sequence of events leading to the formation of oxygen during the S3->S4->S0 tran-sition, wherein the inorganic Mn4Ca(µ-O)6(OHx)4 cluster finishes photo-catalyzing the water splitting reaction (Greife et al, Nature 2023, 617, 623-628; Bhowmick et al, Nature 2023, 617, 629-636) . During this final step a tyrosine radical (TyrZ), stable for a couple of milliseconds, oxidizes a cluster bound oxygen while the hydrogen bonding patterns of nearby waters shift a proton away. A treatment of this redox reaction within the context of accepted transition state theories predicts rate constants that are significantly higher than experimentally recovered values (10^12s^-1 versus 10^3s^-1). In an effort to understand this disparity, temperature dependent experiments have revealed large entropic con-tributions to the rates with only a moderate energy of activation. We suggest that the entropic source may be related to the observed proton rearrangements, and further possible near isoenergetic variations in the nearby extended h-bonding network de-laying the realization of an ‘ideal’ transition state. In the following we explore this re-lation in the context of Eyring’s transition state theory and Marcus’ electron transfer theory, and evaluate their compatibility with the experimental evidence.

Two gallium porphyrins, a tetraphenyl GaCl porphyrin, termed as (TPP)GaCl, and an octaethylporphyrin GaCl porphyrin, termed as (OEP)GaCl were synthesized to use as electron cascade in ternary organic bulk heterojunction films. A perfect matching of both gallium porphyrins energy levels with that of poly(3-hexylthiophene-2,5-diyl) (P3HT) or poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT) polymer donor and the 6,6-phenyl C71 butyric acid methyl ester (PCBM) fullerene acceptor forming an efficient cascade system that could facilitate electron transfer between donor and acceptor was demonstrated. Therefore, ternary organic solar cells (OSCs) using the two porphyrins in various concentration were fabricated, where a performance enhancement was obtained. In particular, (TPP)GaCl-based ternary OSCs of low concentration (1:0.05 vv%) exhibited a ~17 % increase of the power conversion efficiency (PCE) compared with the binary device due to improved exciton dissociation, electron transport and reduced recombination. On the other hand, ternary OSCs with the (TPP)GaCl of high concentration (1:0.1 vv%) and (OEP)GaCl (1:0.05 and 1:0.1 vv%) showed poorest efficiencies due to very rough nanomorphology and suppressed crystallinity of ternary films when the GaCl porphyrin introduced in the blend, as revealed from X-ray diffraction (XRD) and atomic force microscopy (AFM). The best performed devices exhibited also improved photostability, when exposed to sunlight illumination for a period of 8 h than the binary OSCs, attributed to the suppressed photodegradation of the ternary (TPP)GaCl 1:0.05-based photoactive film.

The SARS-CoV-2 virus, causative agent of COVID-19, is known for its genetic diversity. Virus variants of concern (VOCs) as well as variants of interest (VOIs) are classified by the World Health Organization (WHO) according to their potential risk to global health. This study seeks to enhance the identification and classification of such variants by developing a novel bioinformatics criterion centered on the virus's spike protein (SP1), a key player in host cell entry, immune response, and a mutational hotspot. To achieve this, we pioneered a unique phylogenetic algorithm which calculates EIIP-entropy as a distance measure based on the distribution of the Electron-Ion Interaction Potential (EIIP) of amino acids in SP1. This method offers a comprehensive, scalable, and rapid approach to analyze large genomic data sets and predict the impact of specific mutations. This innovative approach provides a robust tool for classifying emergent SARS-CoV-2 variants into potential VOCs or VOIs. It could significantly augment surveillance efforts and understanding of variant characteristics, while also offering potential applicability to the analysis and classification of other emerging viral pathogens and enhancing global readiness against emerging and re-emerging viral pathogens.

The precise differentiation of renal cell tumours (RCTs) is sometimes hard to achieve using standard imaging and histopathological methods. This study investigated 43 cell renal cell car-cinomas (ccRCC), 15 papillary renal cell carcinomas (pRCC), 20 chromophobe renal cell carcino-mas (chRCC), and 18 renal oncocytomas (RO), stained with anti-mitochondria antibody (Thermo Scientific) by immunohistochemistry and immunofluorescence, and assessed by electron micros-copy, in order to define mitochondria distribution pattern (coarse scanty, moderate granular and diffuse granular). Thus, the majority of males had coarse granular staining in the tumours, while females were almost equally distributed among groups (p=0.005). An average patient age, tumour side and dimension, and tumour stage were similar in all staining pattern groups. However, pathohistological tumour types had significantly different expression patterns, with the lower amount of staining detected in majority of ccRCC, moderate expression in all chRCC, and diffuse expression in all RO, pRCC and two cases of ccRCC (p<0.001) presented with higher nuclear grade (p=0.005). Moreover, with increased distribution of mitochondria, the intensity of staining was higher (p<0.001). Here we present a strategy that utilizes mitochondria detection to differentiate RO from chRCC, as well as to distinguish other frequent RCTs, such as ccRCC and pRCC.

Tick-borne encephalitis virus (TBEV) is a RNA-containing enveloped virus, a member of the Flaviviridae family. Here we describe a detailed analysis of the size and structure of inactivated TBEV (the Sofyin-Chumakov TBEV strain, used in vaccines). Four analytical methods were used to analyze individual TBEV particles—negative staining TEM, cryo-EM, AFM, and NTA. All methods confirmed that the particles were monodisperse, and their mean size was ~50 nm. Cryo-EM data were used to obtain a 3D electron density model of the virus with clearly distinguishable E-proteins. STEM-EELS analysis detected phosphorous in the particles, which was interpreted as the RNA signal. Altogether, the described analytical procedures can be valuable for the further analysis of vaccine inactivated virus samples.

Although pollination is one of the most crucial biological processes that ensures plant reproduction, its mechanisms are poorly understood. Especially in insect-mediated pollination, a pollen undergoes several attachment and detachment cycles when being transfered from anther to insect and from insect to stigma. The influence of the surface properties of pollen, insect and floral surfaces on the adhesion forces that mediate pollen transfer are poorly studied. Here, we investigate the adhesive properties of Hypochaeris radicata pollen and their dependence on pollen ageing by quantifying the pull-off forces from glass slides using centrifugation and atomic force microscopy. We found that the properties of the pollenkitt – the viscous, lipid liquid on the surface of most pollen grains – influences the forces necessary to detach a pollen from hydrophilic surfaces. Our results show that aged H. radicata pollen form weaker adhesions to hydrophilic glass than fresh ones. On the other hand, when a pollen grain ages in contact with glass, the adhesion between the two surfaces increases over time. This study shows for the first time the pollen ageing effect on the pollination mechanism.

Due to their short range (2–500 nm), Auger electrons (Auger e-) have the potential to induce nano-scale physiochemical damage to biomolecules. Although DNA is the primary target of Au-ger e-, it remains challenging to maximize the interaction between Auger e- and DNA. To assess the DNA-damaging effect of Auger e- released as close as possible to DNA without chemical damage, we radio-synthesized no-carrier-added (n.c.a.) [189, 191Pt]cisplatin and evaluated both its in vitro properties and DNA-damaging effect. Cellular uptake, intracellular distribution, and DNA binding were investigated, and DNA double-strand breaks (DSBs) were evaluated by im-munofluorescence staining of γH2AX and gel electrophoresis of plasmid DNA. Approximately 20% of intracellular radio-Pt was in a nucleus, and about 2% of intra-nucleus radio-Pt bound to DNA, although uptake of n.c.a. radio-cisplatin was low (0.6% incubated dose after 25-h incuba-tion), resulting in the frequency of cells with γH2AX foci was low (1%). Nevertheless, some cells treated with radio-cisplatin had γH2AX aggregates unlike non-radioactive cisplatin. These findings suggest n.c.a. radio-cisplatin binding to DNA causes severe DSBs by release of Auger e- very close to DNA without chemical damage by carriers. Efficient radio-drug delivery to DNA is necessary for successful clinical application of Auger e-.

High-level quantum-chemical computations (G4MP2) are carried out in the study of complexes featuring tetrel bonding between the carbon atom in the carbenoid CB11H11 - obtained by hydride removal in the C-H bond of the known closo-monocarbadodecaborate anion CB11H12() and acting as Lewis acid (LA) - and Lewis bases (LB) of different type; the electron donor groups in the tetrel bond feature carbon, nitrogen, oxygen, fluorine, silicon, phosphorus, sulphur and chlorine atomic centers in neutral molecules as well as anions H(-), OH(-) and F(-). The empty radial 2pr vacant orbital on the carbon center in CB11H11 , which corresponds to the LUMO, acts as a Lewis acid or electron attractor, as shown by the molecular electrostatic potential (MEP) and electron localization funcion (ELF). The thermochemistry and topological analysis of the complexes {CB11H11:LB} are comprehensively analyzed, and classified according to sharing or closed-shell interactions. ELF analysis shows that the tetrel C···X bond ranges from very polarised bonds, as in H11B11C:F() to very weak interactions as in H11B11C···FH and H11B11C···O=C=O.

The energy E takes the place of the gravitational mass m_G to produce gravity [1]. We wonder whether the inertial mass m_i in the inertial force is also replaced by E. The experiments to measure the inertial force and weight of a carrier are presented. Now we can test the principle of equivalence and study foundations of physics in condensed matter.

The regioselectivity in non-polar [3+2] cycloaddition (32CA) reactions has been studied within the Molecular Electron Density Theory (MEDT) at the B3LYP/6-311G(d,p) level. To this end, the 32CA reactions of nine simplest three-atom-components (TACs) with 2-methylpropane were selected. The electronic structure of the reagents has been characterised through the Electron Localisation Function (ELF) and the Conceptual DFT. The energy profiles of the two regioisomeric reaction paths and ELF of the transition state structures are studied to understand the origin of the regioselectivity in these 32CA reactions. This MEDT study permits to conclude that the least electronegative ends X1 atom of these TACs controls the asynchronicity in the C-X (X = C,N,O) single bond formation, and consequently, the regioselectivity. This behaviour is a consequence of the fact that the creation of the non-bonding electron density required for the formation of the new CX single bonds has a lesser energetic cost at the least electronegative X1 atom than that at the Z3 one.

We review the latest developments in the field of the metal-insulator transition in strongly-correlated two-dimensional electron systems. Particular attention is given to recent discoveries of a sliding quantum electron solid and interaction-induced spectrum flattening at the Fermi level in high-quality silicon-based structures.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In-process EBM monitoring for quality assurance purposes has been a popular research area. Electronic imaging has recently been investigated as one of the in-process EBM data collection methods, alongside thermal/ optical imaging techniques. Despite certain capabilities of an electronic imaging system have been investigated, experiments are yet to be carried out to benchmark one of the most important features of any imaging systems – spatial resolution. This article addresses this knowledge gap by: (1) proposing an indicator for the estimation of spatial resolution which includes the Backscattered Electrons (BSE) information depth, (2) estimating the achievable spatial resolution when electronic imaging is carried out inside an Arcam A1 EBM machine, and (3) presenting an experimental method to conduct edge resolution evaluation with the EBM machine. Analyses of experimental results indicated that the spatial resolution was of the order of 0.3mm-0.4mm when electronic imaging was carried out at room temperature. It is believed that by disseminating an analysis and experimental method to estimate and quantify spatial resolution, this study has contributed to the on-going quality assessment research in the field of in-process monitoring of the EBM process.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. The application of this technology is, however, challenged by the lack of process monitoring and control system that underpins process repeatability and part quality reproducibility. An electronic imaging system prototype has been developed to serve as an EBM monitoring technique, the capabilities of which have been verified at room temperature and at 320+10°C. Nevertheless, in order to fully assess the applicability of this technique, the image quality needs to be investigated at a range of elevated temperatures to fully understand the influence of thermal noise due to heat. In this paper, electronic imaging pilot trials at elevated temperatures, ranging from room temperature to , were carried out. Image quality measure Q of the digital electron images was evaluated, and the influence of temperature was investigated. In this study, raw electronic images generated at higher temperatures had greater Q values, i.e. better global image quality. It has been demonstrated that, for temperatures between , the influence of temperature on electronic image quality was not adversely affecting the visual clarity of image features. It is envisaged that the prototype has significant potential to contribute to in-process EBM monitoring in many manufacturing sectors.

Bimetallic nanoparticles are of interest since they lead to many interesting electrical, chemical, catalytic, and optical properties. They are particularly important in the field of catalysis since they show superior catalytic properties than their monometallic counterparts. The structures of bimetallic nanoparticles depend mainly on the synthesis conditions and the miscibility of the two components. In this work, PdPt alloyed-bimetallic nanoparticles (NPs) were synthesized through the polyol method, and characterized using spherical aberration (Cs) corrected scanning transmission electron microscopy (STEM). High-angle annular dark-field (HAADF)-STEM images of bimetallic nanoparticles were obtained. The contrast of images shows that nanoparticles have an alloy structure with an average size of 8.2 nm. Together with the characterization of nanoparticles, a systematic molecular dynamics simulations study, focused on the structural stability and atomic surface segregation trends in 923-atom PdPt alloyed-bimetallic NPs was carried out.

This work communicates results from optical emission spectroscopy following laser-induced optical breakdown at or near nanomaterial. Selected atomic lines of silver are evaluated for consistent determination of electron density. Comparisons are presented with Balmer series hydrogen results. Of particular interest are measurements free of self-absorption effects. For several silver lines, asymmetries are observed in the recorded line profiles. Electron densities of interest range from 0.5 to 3 × 10¹⁷ cm^-3, for 5 nanosecond Q-switched Nd:YAG radiation at wavelengths of 1064, 532, and 355 nm, and for selected silver emission lines including 328.0, 338.2, 768.7, and 827.3 nm, and the hydrogen alpha Balmer series line at 656.3 nm. Line asymmetries are presented for the 328.0 nm Ag I line that is measured following generation of the plasma due to multiple photon absorption. This work explores electron density variations for different irradiance levels, and reports spectral line asymmetry of resonance lines for different laser fluence levels.

Molecular overtone transitions provide optical frequency transitions sensitive to variation in the proton-to-electron mass ratio (μ = m_p/m_e). However, robust molecular state preparation presents a challenge critical for achieving high precision. Here, we characterize infrared and optical-frequency broadband laser cooling schemes for TeH⁺, a species with multiple electronic transitions amenable to sustained laser control. Using rate equations to simulate laser cooling population dynamics, we estimate the fractional sensitivity to μ attainable using TeH⁺. We find that laser cooling of TeH⁺ can lead to significant improvements on current μ variation limits.

With forty years of developments, bio-macromolecule cryo-electron microscopy has met its revolution of resolution and is playing a very important role in structural biology study. According to different specimen states, cryo-electron microscopy (cryo-EM) involves three specific techniques, single particle analysis (SPA), electron tomography and sub-tomogram averaging, and electron diffraction. All these three techniques have not realized their full potentials of solving structures of bio-macromolecules and therefore need to be developed in the future. In this review, the current existing bottlenecks of cryo-EM SPA are discussed with theoretical analysis, which includes air-water interface during specimen cryo-vitrification, bio-macromolecular conformational heterogeneity, focus gradient within thick specimen, and electron radiation damage. Besides, potential solutions of these bottlenecks are proposed and discussed, which are worthy of further investigations in the future.

The optical conductivity in the charge order phase is calculated in the extended Hubbard model describing an organic Dirac electron system α-(BEDT-TTF)₂I₃ using the mean field theory and the Nakano-Kubo formula. A peak structure due to interband excitation being characteristic in two-dimensional Dirac electron system is found above the charge order gap. It is shown that the peak structure originates from the Van Hove singularities of the conduction and valence bands, where those singularities are located at a saddle point between two Dirac cones in momentum space. The frequency of the peak structure exhibits drastic change in the vicinity of the charge order transition.

The preparation of gold nanoparticles (AuNPs) involves a variety of chemical and physical methods. These methods use toxic and environmentally harmful chemicals. Consequently, the synthesis of AuNPs using green chemistry has been under investigation to develop eco-friendly nanoparticles. One method to achieve this is the use of plant-derived phytochemicals capable of reducing gold ions to produce AuNPs. The aim of this study was to implement a facile microtitre-plate method to screen a large number of aqueous plant extracts to determine the optimum concentration (OC) to bio-synthesize the AuNPs. Several AuNPs of different sizes and shapes were successfully synthesized and characterized from seventeen South African plants. The characterization was done using Ultra Violet-Visible Spectroscopy, Dynamic Light Scattering, High Resolution Transmission Electron Microscopy and Energy-Dispersive X-ray Spectroscopy. We also studied the effects of temperature on the synthesis of the nanoparticles and measured its effect on the particle size of the synthesized AuNPs and the data showed that changes in temperatures affect the size and dispersity of the generated AuNPs. Further, some of the synthesized AuNPs were stable upon incubation with different biological solutions in vitro.

Background. Escalating global plastic production, expected to reach 34,000 million tons by 2050, poses a significant threat to human and environmental well-being, particularly in aquatic ecosystems. Microplastics (MP) and nanoplastics (NP), which originate from the degradation of plastics, are of concern due to their potential bioaccumulation and uptake of pollutants. This study addresses identification methods and focuses on insect meal, a raw material for aquaculture feed. Methods. By using different techniques, the study was able to detect MP and NP in insect meal samples. Chemical digestion with KOH at 60°C efficiently removed organic matter without affecting the synthetic polymer polyethylene (PE). Filtration, confocal Raman microscopy, SEM and TEM were used for comprehensive analysis and integrity tests on PE films were performed using Raman and FTIR spectroscopy. The results showed the presence of PE microplastic particles in the insect meal, which was confirmed by correlative Raman and SEM mapping on a positively charged surface. In addition, the increased resolution of the Raman microscope identified submicrometric PE NP (800 nm). Transmission electron microscopy (TEM) with energy dispersive X-ray spectroscopy (EDX) confirmed plastic-like structures in the insect meal, highlighting the presence of PE plastics characterized by irregular shapes and some agglomeration. The higher carbon concentration in the EDX analysis supported the plastic nature, which was also confirmed by Raman spectroscopy. Conclusions. The study provides a robust method for the detection of MP and NP in insect meal and provides valuable insight into the possible presence of plastics in insect-based aquafeeds. The combination of different analytical methods increases the reliability of the results and sets the stage for future investigations that could focus on the quantification of NP and the assessment of their potential environmental impact.

A novel cytoplasmic dye decolorizing peroxidase from Dictyostelium discoideum was investigated that oxidizes anthraquinone dyes, lignin model compounds and general peroxidase substrates like ABTS efficiently. Unlike related enzymes, an aspartate residue replaces the first glycine of the conserved GXXDG motif in Dictyostelium DyPA. In solution, Dictyostelium DyPA exists as a stable dimer with the side chain of Asp146 contributing to the stabilization of the dimer interface by extending the hydrogen bond network connecting two monomers. To gain mechanistic insights, we solved the Dictyostelium DyPA structures in the absence of substrate as well as in the presence of potassium cyanide and veratryl alcohol to 1.7, 1.85, and 1.6 Å resolution, respectively. The active site of Dictyostelium DyPA has a hexa-coordinated heme iron with a histidine residue at the proximal axial position and either an activated oxygen or CN^- molecule at the distal axial position. Asp149 is in an optimal conformation to accept a proton from H₂O₂ during the formation of compound I. Two potential distal solvent channels and a conserved shallow pocket leading to the heme molecule were found in Dictyostelium DyPA. Further, we identified two substrate-binding pockets per monomer in Dictyostelium DyPA at the dimer interface. Long-range electron transfer pathways associated with a hydrogen-bonding network that connects the substrate-binding sites with the heme moiety are described.

In India, epilepsy is often viewed with superstition, considered a curse rather than a medical condition. Unfortunately, many affected individuals never receive proper medical attention from neurologists, leading them to seek out alternative remedies, including sorcery. Presently, the number of neurologists in India stands at approximately 3000, a concerning figure given the prevalence of epilepsy, which is reported to affect 5.59 to 10 individuals per 1000. This equates to over one million epilepsy patients across the country, representing more than 1% of the total population. Alarmingly, rural areas experience a higher incidence of epilepsy, around 2%, compared to urban centres, where the incidence is approximately 0.5%. This stark contrast underscores the urgent need for improved access to neurological care, particularly in underserved regions.The term "epilepsy" originates from the Greek verb meaning "to seize" or "to get hold of," forming the basis of its etymology. In certain societies, epilepsy is still interpreted as a "penalty for involvement in a forbidden ritual," although perceptions vary among different cultural groups. Individuals diagnosed with epilepsy (PWE) often exhibit behaviours that have led some to speculate about demonic possession or past-life transgressions as causative factors. Consequently, the term "epilepsy" carries diverse social connotations, leading to variations in treatment approaches based on differing perspectives of the condition. Regrettably, some negative attitudes towards epilepsy have fueled stigma, enduring disability, and significant adverse outcomes for those living with the condition.The majority of unreported cases turn to sorcery, exacerbating the already high mortality rates associated with epilepsy disorder and status epilepticus. Various treatment modalities exist for patients with epilepsy to manage their seizures. Given the debilitating and life-altering nature of epilepsy, India offers a range of options including medications (antiepileptic drugs or AEDs), devices, and surgical interventions. When an individual receives a diagnosis of epilepsy (defined as experiencing at least two unprovoked seizures within a short timeframe), life can be dramatically impacted. Several cases highlight the challenges patients face, leading to an increase in Disability Adjusted Life Years (DALY) overall. For newly born infants, constant vigilance from the mother is essential to monitor for any signs of seizure activity around the clock. When a pediatric patient is enrolled in school, their education is often profoundly disrupted. Should the patient be female, her existence would undergo a profound transformation, marked by societal perceptions deeming her as unfortunate and rendering the prospect of marriage untenable. Seizures in young adults precipitate job loss, thereby exacerbating societal burdens. Conclusion: There is a pressing need to raise awareness about epilepsy among the general populace of India. Dispelling misconceptions surrounding epilepsy is essential to steer individuals away from reliance on superstition, and instead, encourage them to seek guidance from certified specialists in nervous system disorders. Thankfully, by following the treatment regimen prescribed by a qualified neurologist, patients can significantly increase their chances of living a life free from seizures, thereby enhancing their overall quality of life and personal fulfilment.

This study examines the nexus between oil prices and inflation in G20 economies, addressing critical gaps by adopting a comparative approach across three pivotal oil price downturns in 2008, 2014, and 2020 (COVID-19). The study utilized monthly time series data from January 2000 to December 2023 and the Bayesian Structural Time Series (BSTS) approach for causal impact analysis. The study found that during the global financial crisis (December 2007 to June 2014), advanced economies like Australia and the UK displayed varying degrees of negative absolute causal impact, aligning with the deflationary impact of falling oil prices. In contrast, emerging economies faced significant negative causal impacts. From June 2014 to January 2020, diverse inflation impacts were observed across G20 economies after a significant oil price decline. Advanced economies like Australia and emerging economies like Brazil experienced negative impacts, while others showed negligible effects. In the subsequent period from January 2020 to December 2023, amid the COVID-19 pandemic and substantial oil price decline, G20 countries exhibited varied inflation outcomes. Positive absolute effects indicated a notable rise in inflation with China standing out with a substantial negative impact. The wavelet coherence analyses also showed an asymmetrical impact of oil prices on inflation. The findings suggest that policymakers should adopt proactive and adaptive policy frameworks, considering the asymmetric responses of G20 economies to oil price dynamics.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

This article conceptualises the link between firms’ value chains and distribution networks and the requirements for double materiality assessments in contemporary reporting regulations worldwide. The new European Sustainability Reporting Standards (ESRS) and the standards for sustainability reporting issued by the International Sustainability Standards Board (ISSB), called IFRS S1 and IFRS S2, require companies to report their own direct (scope 1) and indirect (scope 2) greenhouse gas (GHG) emissions as well as GHG emissions in their value chains and distribution networks (both scope 3). However, GHG emissions comprise just one dimension of information that is relevant to understand when assessing, managing and reporting the footprints and impacts of a firm and are, therefore, only a fraction of the key performance indicators (KPIs) related to ESG that should be disclosed. Through a case study, this article demonstrates the connection between the due diligence analysis of firms’ value chains and distribution networks, the analysis of the competitive parameters of the business model, the identified impacts, risks and opportunities, and the double materiality perspective. The double materiality perspective prioritises actions based on probability and significance, creating a natural space to identify KPIs. The article concludes by applying the REGS model and illustrating how it can assist firms in identifying relevant KPIs based on double-materiality assessments.

The Pearl River Delta (PRD) has undergone complex geological development within a multi-island faulted basin, shaped by the interplay of regional tectonic movements, Quaternary sea-level fluctuations, and fluvial-marine interactions. Despite a great number of studies on the Holocene sedimentary sequences and spatial difference of lithofacies and environments, scant attention has been paid to the overarching human influence on deltaic evolution and coastline modifications since the Neolithic epoch. To further elucidate the spatial variation in Holocene sedimentation and its underlying basement topography shaped during the Last Glacial Maximum (LGM), we compiled a comprehensive dataset incorporating borehole data from over 2,800 cores within the PRD. Subsequently, high-resolution isobath maps of Quaternary deltaic deposits were generated, offering unprecedented insights into sediment distribution. This dataset facilitated a nuanced reconstruction of pre-Holocene topography, revealing a zone characterized by elongated, deep-incised valleys governed by NW-SE fault orientations. Further, we delineated coastline shifts since the period of maximum marine transgression (~7000 years BP), contributing to an enhanced understanding of the formation and evolutionary patterns of the delta and the river network oscillations. Our findings illuminate increasing anthropogenic impact on the rate of fluvial sedimentation and land growth, particularly accentuated over the last two millennia, favoring deltaic accretion. The current study has considerable implications for understanding the dynamic interplay between land-sea interactions and anthropogenic activities in shaping the delta, and stands to significantly inform land and resource management strategies, as well as future urban planning within the delta's bay areas.

Abstract: The species composition, the structure of phytoplankton communities, hydrochemical parameters in the artificial cooling reservoir of one of the largest thermal power plants (TPP) in the north-east of Europe in the Pechora River basin, Komi Republic were studied in the ice-open period in June and August. Altogether 81 species of algae and cyanobacteria was revealed with the last one predominated. Among cyanobacteria and algae (Bacillariophyta, Chlorophyta), indicators of water quality were found. Assessment of water quality according to the species composition and abundance of indicator phytoplankton species showed that the waters of the Pechorskoe Reservoir can be at-tributed to the III class of water quality, beta-mesosaprobic self-purification zone, with water quality of satisfactory purity, retaining the ability to self-purify. An increase in the diversity of plankton communities and high values of their abundance and biomass under the influence of the warming effect of TPP water outlet were noted and revealed its spatial distribution over the reservoir surface. The plankton of the northern reservoir under the influence of warm waters indicates a slight in-crease in the trophic status of the studied water body, which is also confirmed by the data of hydrochemical analysis. Ecological mapping for the chemical and biological variables as well as pollution indices over the water area of the reservoir was carried out. The results obtained can be used to make forecasts of changes in the phototrophic biota of small northern water bodies under the conditions of climate change.

The use of bioethanol in cooking is not new, but until recently its application has been confined exclusively to small scale projects. However, a new bioethanol cooking utility in Kenya has now reached mass market adoption, serving more than 950,000 households with cooking fuel since launching in late 2019. Its success was made possible by a significant investment in technology to facilitate safe, convenient and affordable fuel distribution. It is funded by climate finance which is based on bioethanol fuel replacing charcoal used for cooking, a leading cause of African defor-estation. This development has been so recent that it has not widely been discussed in the academic literature. More broadly, the health, environmental and economic impacts of bioethanol for cooking have not been systematically assembled in one place. This article details what is known about the impact of bioethanol for cooking, how and why bioethanol for cooking was able to suddenly reach commercially viable scale in spite of the challenges it faced. It also discusses implications for further scaling of clean cooking fuel solutions.

Wood plastic composite usage and demands have increased due to chemical, and mechanical properties when compared to plastic materials. However, because of the possibility of structural and mechanical changes of the material when exposed to external environment more research needs to be done. In the present study yellow birch/HDPE composites materials made by injection molding were treated by zinc oxide and exposed to fungal rots. Mechanical properties of the composites were assessed by Tensile and Izod impact test. The impact energies of the samples loaded with 30 % ZnO-treated fibers and exposed to G. trabeum and T. versicolor decreased, compared to when samples were not treated with ZnO. The mechanical properties of all samples treated with ZnO and exposed to rot decreased which were reported as a decreased Young's modulus and impact energies. ZnO prevented mycelium proliferation which was nonexistent on samples. It has been noted that the decrease in mechanical properties of treated samples was due to NaOH used to dissolve the ZnO powder.

The decreasing width, increasing aspect ratio RDL presents significant challenges to design for reliability (DFR) of advanced package. Therefore, this paper proposes a ML based RDL modeling and simulation method. In the method, RDL is divided into blocks and subdivided into pixels of metal percentage, and the RDL is digitalized as tensors. Then, an ANN-based surrogate model is built and trained by a subset of tensors to predict the equivalent material properties of each block. Lastly, all blocks are transformed into elements for simulations. For validation, line bending simulations were conducted on an RDL, with the reaction force as accuracy indicator. The results show that neglecting layout impact causes critical errors as substrate thins. By the method, the reaction force error is 2.81% and the layout impact can accurately be considered with 200×200 elements. For application, the TCT maximum temperature state simulation was conducted on a CPU chip. The simulation indicates that for advanced package the maximum stress more likely occurs in RDL rather than bumps, both RDL and bumps are critical impacted by layouts, and RDL stress is also impacted by vias/bumps. The proposed method precisely concerns layout impacts with little resources, presents an opportunity of efficiency improvement.

Sustainable supply chains have become increasingly crucial to address environmental and social challenges faced by societies worldwide. Last-mile delivery, which involves delivering products from a distribution center or warehouse to the final destination, typically a consumer's doorstep, is an essential component of the supply chain. However, it faces numerous challenges such as traffic congestion, air and noise pollution, and carbon emissions. This research paper explores the viability of last-mile delivery solutions for sustainable supply chains. The study reviews the literature on last-mile delivery challenges, sustainable last-mile delivery solutions, and case studies of sustainable last-mile delivery solutions. The results indicate that innovative last-mile delivery solutions, such as electric vehicles, cargo bikes, and drones, have the potential to reduce environmental impact and improve the efficiency of last-mile delivery while enhancing social equity. Additionally, partnerships between different stakeholders, including governments, logistics companies, and consumers, can contribute to the development of sustainable last-mile delivery solutions. The study concludes that sustainable last-mile delivery solutions are essential to achieving sustainable supply chains and recommends further research to explore the economic feasibility and scalability of these solutions.

Large Language Models (LLMs) have revolutionized the field of Artificial Intelligence with their ability to understand and generate natural language discourse. This has led to the use of LLMs in various creative fields such as music, art, and storytelling, which has sparked a debate on the impact of LLMs on human creativity. This article explores the cyclic effect of LLMs on human creativity, where LLMs can generate an ever-evolving cycle of creative output from both humans and machines. The article also highlights the importance of responsible and ethical use of LLMs, including privacy and copyright issues with the training data used by LLMs. The article emphasizes the need for transparency, data security measures, and AI governance policies to protect user data and ensure the safe use of LLMs. It also calls for the development of educational materials and resources to increase public understanding of LLMs and their ethical implications. The article concludes by highlighting the potential of LLMs as powerful tools for communication and education, but also emphasizes the need for ethical considerations to ensure the responsible and beneficial use of LLMs in society.

A crop-weed simulation model is presented to compare and evaluate Integrated Weed Management (IWM) strategies. Specifically, the model was parameterized for soybean crops in competition with Euphorbia davidii Subils. We used both, weed and crop demographic data surveyed in agronomic fields of the central zone of the Buenos Aires province, Argentina, throughout two crop cycles (2011/2012 and 2013/2014). The proposed model underwent a calibration process and subsequent validation with 70/30 % data split respectively (N=37). Two annual-based and one multiannual-based case studies were simulated to demonstrate the performance of the model. Different IWM strategies were compared under both, operational and tactical planning horizons through the evaluation of different model outcomes (i.e. crop yield, interspecific competition, economic return, and environmental impact). Our case studies results suggest that the inclusion of cultural management practices could reduce weed interspecific competition by 46 to 97 % and weed seed production by 40 to 89%. An increment in both expected crop yield, by 6 to 20%, and annual gross margin, by 44 to 199 US$.ha-1, were obtained in silico for similar levels of environmental impact.

Anticipating future successional forest trends in the face of ongoing global change is an essential conservation target. Mountain forests are especially sensitive to environmental shifts, and their past responses to climatic and anthropogenic (external) drivers may provide a basis for improving predictions of future developments. This paper uses independent high-resolution palynological and paleoclimatic reconstructions to statistically analyze the long-term effects of external drivers on regional forest succession in the central Iberian Pyrenees during the last 500 years. The dominant taxa of these forests (Quercus, Betula, Pinus) showed significant relationships with summer temperature, summer drought and autumn precipitation. Immediate and delayed (by two or more decades) responses of these trees to climatic drivers were identified. Regional succession showed a closed path, starting at the end points around the attraction domain of pine-dominated forests. This trajectory was determined by a trend toward anthropogenic forest clearing (16th to 18th centuries) and a reverse trend of natural forest recovery (18th to 20th centuries). Forest clearing was due to burning, facilitated by drought, and was followed by the expansion of cropping and grazing lands. Forest recovery was fostered by reduced human pressure and rising temperatures. The statistical approach used in this work has unraveled ecological relationships that remained unnoticed in previous works and would be important for predicting future successional trends under changing climates. The reported response lags of individual taxa to climatic drivers may complicate the establishment of reliable ecological relationships and should be addressed in future studies.

Since the exploitation of mineral resources results in the release of radionuclides, and consuming radionuclides affects public health in the short and long term. A case study of the environmental radiation impact from coal mining and germanium processing was carried out in southwest China. The coal mines contain germanium and uranium and have been exploited for more than 40 years. The farmlands around the site of coal mining and germanium processing have been contaminated by the solid waste and mine water in some extend since then. Samples of crops have been collected from contaminated farmlands in research area. The research area covers a radius of 5 km, in which there are 2 coal mines located. 210Pb and 210Po have been analyzed as the key radionuclides during monitoring program. The average activity concentrations of 210Pb and 210Po in the crops were 1.38 and 1.32 Bq/kg in cereals, 4.07 and 2.19 Bq/kg in leafy vegetables and 1.63 and 1.32 Bq/kg in root vegetables. The annual effective doses due to the ingestion of 210Pb and 210Po in consumed crops have been estimated for adult residents living in research area. The average annual effective dose was 0.336mSv/a, while the minimum was 0.171 mSv/a and the maximum was 0.948 mSv/a. The results show that crops grown on contaminated farmland contained an enhanced level of radioactivity concentration. Ingestion doses of local residents in research area were significantly higher than the China average level of 0.112 mSv/a, and the world average level of 0.042 mSv/a through 210Pb and 210Po in crops intake respectively.

This paper summarizes the estimates of the total changes in sales, expenses, and income of participants of the horticulture research and extension programs at the Mississippi State University - Coastal Research and Extension Center for the past five years. Major items outline the estimation procedures for the past five years. The average annual values were used in estimating the total economic impacts of added gross sales, expenses, and incomes of participants in horticulture events. The cumulative total impacts reach $8.7 million in sales, 76 jobs, $1.4 million in labor income, $2.4 million in value-added, and $0.4 million in local, state, and federal taxes. In addition, the total willingness to pay for the horticulture program by the adult participants reached $1.8 million. In comparison, the annual public spending on the horticulture program averaged $1.4 million, creating additional substantial economic impacts to the region.

This article analyses the environmental impact of the measures imposed during the SARS-CoV-2 pandemic. We compare the evolution of atmospheric pollution levels in recent years and during lockdown, and assess the effects of the decrease in mobility and changes in patterns and lifestyles during the latter period. Thus, the reduction in the risk to human health brought about by the improvement of air quality during the months of confinement through the use of dose-response functions is estimated. The focus of the case study is the island of Tenerife. The island of Tenerife has been selected because it can serve as an example for other sites in Europe. We distinguish between the three areas with the highest population concentrations: the Metropolitan, Southern, and Northern areas. The impacts of air pollution and its relationship with changes in consumption and activity patterns are clearly distinguishable. Therefore, the lessons learned can be easily extrapolated to other areas, in both island and mainland contexts.

The COVID-19 pandemic has left no one indifferent: all around the globe, people have felt the massive impact of a virus that has stopped the world in its tracks. Many countries have been forced to impose strict lockdowns, causing devastating damage to the overall economy and welfare state, but also leaving an unprecedented emotional footprint on almost everyone. In this paper, we aim to quantify, by building our own method how, this pandemic has affected people emotionally by detecting the shifts in the emotional profile of representative users in selected countries. Our method processes the social media stream adapting the Pleasure-Arousal-Dominance (PAD) approach to measure emotional states on the Russell Circumplex plane, allowing for not only an overall emotional shift quantification but also a detailed analysis at mood level. By focusing on certain emotions and searching behavior, we establish a relationship between the pandemic and the emotional response. Although the method can be applied to any location with a significant and varied amount of geo-localized social media streams, the scope of this paper covers the most representative cities in Europe.

With increasing interest in understanding contribution of secondary organic aerosol (SOA) to particulate air pollution in urban areas, an exploratory study was carried out to determine levels of carbonaceous aerosols and polycyclic aromatic hydrocarbons (PAHs) in the City of Kuala Lumpur, Malaysia. PM2.5 samples were collected using a high-volume sampler for 24 h in several areas in Kuala Lumpur during the north-easterly monsoon from January to March 2019. Samples were analysed for water soluble organic carbon (WSOC), organic carbon (OC), elemental carbon (EC) and secondary organic carbon (SOC) in PM2.5 was estimated. Particle-bound PAHs were analysed using gas chromatography-flame ionization detector (GC-FID). Average concentrations of WSOC, OC and EC were 2.7 ± 2.2 (range of 0.63-9.1) µg/m3, 6.9 ± 4.9 (3.1-24.1) µg/m3 and 3.7 ± 1.6 (1.3-6.8) µg/m3, respectively, with estimated average SOC of 2.3 µg/m3, contributing 34% to total OC. The average of total PAHs was 1.8 ± 2.7 ng/m3. Source identification methods revealed natural gas and biomass burning, and urban traffic combustion as dominant sources of PAHs in Kuala Lumpur. To understand human health risk posed by PAHs, a deterministic screening health risk assessment was also conducted for several age groups including infant, toddler, children, adolescent and adult. The total concentration of BaPeq is 3.8 ng/m3, with the average of 0.29 (range of 0.001-1.6) ng/m3. Carcinogenic and non-carcinogenic risk of PAH species were well below the acceptable levels recommended by the USEPA. Future work is needed using long-term monitoring data to understand the origin of PAH contributing to SOA formation and to apply source-risk apportionment to know better the potential risk factors posed by the various sources in urban areas in Kuala Lumpur.

The performance of a normal-strength SHCC under impact loading was studied using the results obtained from a split Hopkinson tension bar (SHTB). The focus of the investigation is to explain the mechanisms behind the peculiar rate-dependent behavior of SHCC under tensile loading. With the help of frames obtained by high-speed cameras and the subsequent Digital Image Correlation (DIC) analysis, the stress-strain relation of the SHCC obtained in SHTB was analyzed. The investigation of the composite’s behavior was supported by constituent-level experiments on the non-reinforced matrix of the SHCC and on the fiber-matrix bond. In the case of the constituent matrix, the well-known apparent increase in the tensile strength of the cement-based matrix and its influence on the behavior of SHCC was studied. For this purpose, experiments on the SHCC specimens with different geometries were performed in the SHTB. The results obtained from these experiments and those obtained by DIC show that commonly used analytical models, in which the specimen is assumed elastic, cannot capture the effects of structural inertia on the results. Thus, an alternative novel method based on the results of DIC has been used to explain and quantify the contribution of structural inertia. The rate-dependent behavior of the fiber-matrix bond was studied by performing high-speed single fiber pullout tests in a miniaturized split Hopkinson tension bar. This novel experimental technique enabled explanation of the rate-dependent bridging action of the fibers in SHCC. Based on the results, the enhanced behavior of SHCC under impact loading is explained.

COVID‑19 pandemic, also known as the coronavirus pandemic, has spread rapidly across the globe since the end of 2019 and brought impressive changes in our life and living through partial or full lockdown and reduced anthropogenic activities. Hence, it is imperative to investigate the impacts and consequences of COVID-19 on global eco-system and environment. The present study accordingly addresses the impacts and consequences of COVID-19 by ten environmental indicators; viz., global warming (or greenhouse gas emission), stratospheric ozone depletion, ozone formation (on human health), fine particulate matter formation, smog, ionizing radiation, human carcinogenic toxicity, human non-carcinogenic toxicity, water resource consumption, and effect on human health. The overall study has been performed in agreement with the standard principle and guidelines of life cycle assessment. Worldwide changes in consumption of fossil fuels, viz., petroleum, coal and natural gas, as a result of COVID-19 pandemic, has been the core theme of the study. Outcomes from the study show that COVID-19 has been a ‘blessing in disguise’ for the global environment with most of the above-mentioned indicators declining by approximately 20-30% in 2020 in comparison to the 2019 level.

The paper presents a conceptual model of the route of macroplastic debris (5 > mm) through a fluvial system, which can support future works on the overlooked processes of macroplastic storage and remobilization in rivers. We divided the macroplastic route into (1) input, (2) transport, (3) storage, (4) remobilization and (5) output phases. Phase 1 is mainly controlled by humans, phases 2–4 by fluvial processes, and phase 5 by both types of controls. We hypothesize that natural characteristics of fluvial systems and their modification by dam reservoirs and flood embankments construction are key controls on macroplastic storage and remobilization in rivers. The zone of macroplastic storage can be defined as a river floodplain inundated since the beginning of widespread disposal of plastic waste to the environment in the 1960s and remobilization zone as a part of the storage zone influenced by floodwaters and bank erosion. The amount of macroplastic in both zones can be estimated using data on the abundance of surface- and subsurface-stored macroplastic and the lateral and vertical extent of the zones. Our model creates the framework for estimation of how much plastic has accumulated in rivers and will be present in future riverscapes.

In recent years, the anticipation of sustainable commercial supersonic jet operations has elevated again. Advances in propulsion together with the increased usage of composite materials favour the potential of sustained and cost efficient supersonic commercial operations. However, obstacles remain with regards to the certification of the new supersonic aircraft platforms, while the two main certification bodies EASA and FAA are under pressure to develop certification requirements which will reassure that the supersonic operations are going to have the least possible environmental impact. From a design perspective, past and current research suggests that a trade-off exists between the aircraft performance and the environmental impact, which should be balanced. The current study attempts to balance this trade-off and to conceptually design a SuperSonic Business Jet (SSBJ) by taking into account environmental concerns of the supersonic flight together with design methods that facilitate a sustained supersonic cruise. An environmental impact assessment is undertaken for the SSBJ design and its results are compared to a typical commercial subsonic airliner.

Iron deficiency anemia (IDA) is highly prevalent in the Cote d’Ivoire, and has severe health and economic consequences. In this paper, we apply a health economic model to quantify the burden of IDA, and the contribution of nation-wide mandatory iron fortification of wheat flour and voluntary iron fortification of condiments to the reduction of this burden. The analysis for the population from six months to 64 years builds on published reviews and publicly available datasets, and is stratified by age-groups and socio-economic strata. Without the impact of these fortification strategies, the annual burden of IDA is estimated at 242,100 disability adjusted life years (DALYs) and 978.1 million USD. Wheat flour and condiment fortification contributed to a reduction of the IDA burden by approximately 5% each. In places with high prevalence of malaria and environmental factors, such as the Côte D’Ivoire, policy makers should combine nutritional intervention with infectious disease prevention and environmental factors. The findings of this study provide additional input for policy makers about the magnitude of the impact and can support the conception of future fortification strategies.

The node position information is critical in the wireless sensor network (WSN). However, the existing positioning algorithms commonly have low positioning accuracy because of noise interferences in communication. To solve this problem, this paper presents an iterative positioning model based on distance correction to improve the positioning accuracy of the target node in WSN. First, the log-distance distribution model of received signal strength indication (RSSI) ranging is built and the noise impact factor is derived based on the model. Second, the initial position coordinates of the target node are obtained based on the triangle centroid localization algorithm, thereby calculating the distance deviation coefficient under the influence of noise. Then, the ratio of the distance measured by the log-normal distribution model to the median distance deviation coefficient is taken as the new distance between the anchor node and the target node. Based on the new distance, the triangular centroid positioning algorithm is used again to calculate the target node coordinates. Finally, the iterative positioning model is constructed, and the distance deviation coefficient is updated repeatedly to update the positioning result until the set number of iterations is reached. Experiment results show that the proposed iterative positioning model can improve positioning accuracy effectively.

The IPAT equation provides a simple but powerful model for understanding sustainability, particularly from the challenge posed by the Anthropocene—how to reduce personal or societal impact. Impact is calculated by multiplying population, affluence and technology, and a ‘reduction coefficient’ e is used to explore targeted reductions in impact of different entities to cap total (summed) impact. The model offers two solutions. First, that all three factors are essential in determining total impact; a focus on just one or two is not justifiable without credibly addressing the other(s). Second, by presenting reduction of impact as a proportion of current activity, the solution becomes accessible to an individual actor (e.g., an individual, family, organization, or country). Application of the model is illustrated based on household weekly food consumption from cultures around the world. The model helps unify a) disparate perspectives on population, affluence and technology, which currently oppose one another from a basis of belief or dogma, and b) different sectors (e.g., food production, energy, climate impacts and others), as well as actors, so they can jointly identify strategies to resolve their contributions to approaching larger scale sustainability.

In 2014, the International Union for Conservation of Nature adopted the Red List of Ecosystems (IUCN RLE) criteria as the global standard for assessing risks to terrestrial, marine, and freshwater ecosystems. Identifying and quantifying the impacts of biodiversity assessments on the status of nature is key to justifying continued investment in assessments and enabling strategic planning to maximize future impact. In this policy perspective, we use an established impact evaluation framework to identify the impacts of the IUCN RLE since its inception. To date, 1,397 ecosystem units in 100 countries have been assessed following the IUCN RLE protocol. Systematic assessments are complete or underway in more than 25 countries and two continental regions (the Americas and Europe). Countries with established ecosystem red lists have already used them to inform legislation, land-use planning, protected area expansion, monitoring and reporting, and ecosystem management. IUCN RLE indices based on systematic assessments have high potential to inform global biodiversity reporting for the Aichi Targets and the United Nations Sustainable Development Goals. Expanding the coverage of IUCN RLE assessments, building capacity to undertake them, and establishing stronger policy instruments to manage red-listed ecosystems will be key to maximizing conservation impacts over the coming decades.

Impact load was applied to hardened cement paste (HCP) specimens using a gas gun to investigate microscopic changes in the specimens and develop a better response model of concrete subjected to impact load. Plasma emission was observed at the moment of impact at 420 m/s and the colour of the portion near the impact point turned brighter. This brighter portion was analysed, and it was observed that the pore structure was coarser compared to the other portion; however, the results of thermogravimetry and X-ray diffraction analysis were similar. A possible reason is that the generated heat was instantaneous and the rate of the temperature increase in the HCP decreased due to evaporation of water in the HCP. These results indicate that during impact at a few hundred m/s, porosity increase due to heat effect is more dominant than porosity decrease due to mechanical compaction.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

This article investigates if public investments in rural basic infrastructure represent the best strategy for boosting the local economy of rural communities from Romania. The article focuses on one specific program implemented under the Cohesion policy in the framework of the National Plan for Rural Development called Measure 322. Geographically, the research included a sample of rural communes from the North-Western Region of Romania. Moreover, the study also looks at other determinants of local economic development (LED) than infrastructure investments, with a focus on certain feature characterizing Romanian rural communities such as population size, isolation from urban centers, connection with European and national roads networks, educational stock, etc. The research included three steps, namely the construction of the LED Index, a cvasi-experimental research, and a regression model. Our main findings seem to suggest that while investments in infrastructure help the development gap between beneficiaries and non-beneficiaries remains relatively the same. In terms of determinants of LED, percentage of population with a university degree and connection to a European road are the most significant in the Romanian rural context.

Researchers, journals, and universities want to receive more citations for their scholarly publications. However, a paper citations depend on its quality, visibility and author’s online profile. Research support documents (unpublished papers, white papers, project reports, datasets, software, posters, online resources and teaching materials) can be additional source for increasing the author’s visibility. To enhance research visibility and impact, the full range of scholarly output should be available online on the open access platform. With open access platform, key research findings are made accessible immediately to the scientific community. Therefore, the publicly available research support documents may result in receiving more citations in addition to the published papers. In this paper we conducted a simplified three stages study on the benefits of research support documents publications on open access platform. We also elaborated on approaches of improving your research visibility and impact through these document.

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

Engineering application of additively manufactured (AM) metallic materials is quite limited by their fatigue behaviors which are very inconsistent with that of conventionally wrought or cast ones. Here, based on advanced material characterization techniques, such as focused ion beam (FIB), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the mi-crostructures underneath fracture surfaces were thoroughly investigated in an AM aluminium (AlSi10Mg) alloy with horizontal and vertical building orientation endured very-high-cycle fa-tigue (VHCF) loading under stress ratios R = –1, 0 and 0.5. Two VHCF failure specimens A and B were representatively selected to further SEM examine and TEM samples preparation via FIB milling. Specimen A was horizontally printed and failed at R = –1; specimen B was vertically printed and failed at R = 0. TEM samples A1 and B1 were lifted from locations near the crack ini-tiation sites on the fracture surfaces of specimens A and B; The locations of TEM samples A2 and B2 kept away from the crack origin sites but still within the “fish-eye” region of crack steady growth. TEM observations show that there was no characteristic microstructure induced by VHCF in different oriented specimens and under various R values.

Crystalline phase engineering is a prominent strategy for synergistically optimizing the sur-face-body phases of a catalyst. In this work, TiO2 nanosheets assembled into nanotubes (TNSTs) with two-phases of anatase and rutile were firstly synthesized via crystal engineering by simple thermal annealing, and subsequently loaded with Ru nanoparticles to create efficient benzene hydrogenation catalyst Ru/TNSTs. The well- designed nanosheet-tubes structure boasts large specific surface area and excellent transmission channels, which effectively prevents the ag-glomeration and deactivation of loaded Ru nanoparticles, as well as promotes the internal diffu-sion in the reaction process of benzene hydrogenation to cyclohexene. Furthermore, titanium dioxide nanosheet-tubes contain numerous Ti3+ defects, which not only improves the overall generation rate of cyclohexene, but also enhances the suppression of cyclohexene adsorption. Most importantly, the two-phases of titanium dioxide increases the ratio of the electron defi-ciencies of Ru and promotes cyclohexene desorption. These synergistic properties enhance the selectivity and efficiency of the Ru/TNSTs catalysts, resulting in excellent performance in the hydrogenation of benzene to cyclohexene. Especially the Ru/TNSTs-4 catalyst achieves a 95% in-itial selectivity and 51% yield of cyclohexene in the reaction, outperforming most supported Ru-based catalysts. This work may provide new perspectives for designing efficient benzene hydrogenation catalysts via crystalline phase engineering.

Superconductivity in highly-pressurized hydrides became primary direction for the exploration of fundamental upper limit for the superconducting transition temperature, Tc, after Drozdov et al (Nature 2015, 525, 73) discovered superconducting state with Tc=203 K in highly-compressed sulphur hydride. To date several dozens of high-temperature superconducting polyhydrides have been discovered. In addition, recently, it was reported that highly-compressed titanium and scandium exhibit record-high (up to 36 K), which is by manifold exceeded of niobium, which is the record high- ambient pressure metallic superconductor. Here we analysed experimental data on for recently discovered high-pressure superconductors (which exhibit high transition temperatures within their classes): elemental titanium (Zhang et al, Nature Communications 2022; Liu et al, Phys. Rev. B 2022), TaH3 (He et al, Chinese Phys. Lett. 2023), LaBeH8 (Song et al, Phys. Rev. Lett. 2023), and black (Li et al, Proc. Natl. Acad. Sci. 2018) and violet (Wu et al, arXiv 2023) phosphorous, to reveal the nonadiabaticity strength constant, TθTF (where Tθ is the Debye temperature, and TF the Fermi temperature) in these superconductors. The analysis showed that δ-phase of titanium and black phosphorous exhibit the Tθ/TF which are nearly identical to ones associated in A15 superconductors, while studied hydrides and violet phosphorous exhibit the constants in the same ballpark with H3S and LaH10.

The field dynamics of neutral and charged matter (treated as gauge fields) beyond the event horizon of black holes are investigated. As an extension of the work done in Ganesan (2023) [1], the analysis was done using the combined dynamics of the two-dimensional Yang-Mills and Liouville gravity fields beyond the event horizon. The quantum interactions and symmetry breaking mechanisms of the combined two-dimensional fields are discussed. The second part of this paper explores the quantum dynamics occurring at the event horizon. By considering the structure of the event horizon as a Möbius strip (embedded in three-dimensional space), a formulation for the lower bound of the first energy eigenvalue of a quantum particle (electron) at the event horizon is obtained.

In order to study the effects of irradiation on the physicochemical properties and digestion behavior of chickpea protein, chickpea protein concentrate (CPC) was treated with electron beam irradiation (EBI) at doses of 5, 10, 15 and 20 kGy, respectively. After irradiation, protein solubility first increased at 10 kGy and 15 kGy, and then decreased at higher dose of 20 kGy. This was supported by SDS-PAGE where the intensity of major protein bands first increased and then decreased. Increased does of EBI generally led to greater oxidative modification of proteins in CPC, indicated by reduced sulfhydryls and increased carbonyls. In addition, protein structure was modified by EBI shown by Fourier transform infrared spectroscopy analysis where α-helix generally decreased and β-sheet increased. Although the protein digestibility was not significantly affected by EBI, the peptidomic analysis of the digests revealed significant difference among CPC irradiated with varying doses. A total of 337 peptides were identified from CPC irradiated with 0 kGy, 10 kGy and 20 kGy, respectively, with 18 overlapping peptides and 60, 29 and 40 peptides specific to the groups of 0, 10 and 20 kGy respectively. Theoretical calculation showed that the distribution of peptide length, hydrophobicity, net charge, and C-terminal residues were affected by irradiation. The 2, 2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity showed a marginal decrease with increasing dose of irradiation. In conclusion, EBI led to oxidative modification and structural changes of the chickpea protein, which subsequently affected the physicochemical properties of peptides obtained from in-vitro digestion of CPC despite of similar digestibility.

Microbial fuel cells (MFCs) offer sustainable solutions for various biotechnological applications and are a crucial area of research in biotechnology. MFCs can effectively treat wastewater and biodiesel waste by decomposing organic matter and generating electricity. Certain Pseudomonas species possess extracellular electron transfer (EET) pathways, enabling them to transfer electrons from organic compounds to the MFC's anode. Moreover, Pseudomonas species can grow under low oxygen conditions, which is advantageous considering that the electron transfer process in an MFC typically leads to reduced oxygen levels at the anode. This study focuses on evaluating MFCs inoculated with a new Pseudomonas species, grown with 1 g.L-1 glycerol, a common byproduct of biodiesel production. Pseudomonas sp. BJa5 exhibited a maximum power density of 39 mW.m-2. Also, the observed voltammograms and genome analysis indicate the potential production of novel redox mediators by BJa5. Additionally, we investigated the bacterium's potential as a synthetic biology non model chassis. Through testing various genetic parts, including constitutive promoters, replication origins, and cargos using pSEVA vectors as a scaffold, we assessed the bacterium's suitability. Overall, our findings offer valuable insights into utilizing Pseudomonas spp. BJa5 as a novel chassis for MFCs. Synthetic biology approaches can further enhance the performance of this bacterium in MFCs, providing avenues for improvement.

Maxwell's electric equation and Schrödinger quantum equation are used to find useful expressions for the probability of electrons existence and the electrons transport. The first expression which uses special relatively also shows that the probability of the electrons existence is higher for lower energy states compared to higher energy states where the probability is low. This means that electrons transport takes place from higher energy states to lower states. This conforms to the laws of chemistry where the atom tends to be stable by forcing electrons to occupy lower energy states. The second expression used the momentum velocity relation instead of special relatively. This expression shows also electrons transport from higher to lower states. It also shows that the probability of the electrons existence is higher for lower electrons density regions and lower for higher electrons density regions. This means that the electrons transport is from higher density regions to lower density regions. This conforms to the diffusion law.

Measured values of the electron mass and Compton wavelength produce a value of Planck's constant with a relative standard uncertainty of 3 x 10^-10. This is only slightly larger than the 1.3 x 10^-10 relative standard uncertainty in measurements performed using the Kibble balance. Compton scattering represents an alternative pathway to improving the value of Planck's constant in the future. Natural units of length, mass, and time offer new pathways to improving the values of physical constants. While extensive values of the Planck units lie beyond the reach of present-day instrumentation, certain product and quotient pairs of Planck units such as the speed of light can be measured with relatively high precision. Better measurements of certain unit pairs will improve the value of the gravitational constant.

In this review, photoinduced electron transfer processes in specifically designed assembled ar-chitectures have been investigated on the basis of recent results reported from our laboratories. A convenient and useful way to study these kinds of systems has been described in order to under-stand the rules that drive to a light induced charge separation and its subsequent decay to the ground state, also with the aim of offering a tutorial for young researchers. Assembled systems of covalent or supramolecular nature have been presented and some functional multicomponent systems for the conversion of light energy into chemical energy have been discussed.

Technology is in the way to reach in its climax but the basic understanding of science in many phenomena is still awaited even though the nature witnesses it. Scientific research reveals strong analogy between photon and electron. When an atom deals neutral state, it levitates electron of outer ring from the back surface while placing the bit-energy at front surface. Gravitation behavior of that electron starts at the centre of relaxation point by including the force of side pole where the pulling force of nearby unfilled state of that atom from the front surface results into depict forcing energy shape like Gaussian distribution symbol with both ends turned called unit photon. The inertia is being involved at each stage of changing direction of that electron by introducing the disappearances of forces of two poles against the appearances of forces of two opposite poles during rest to motion and motion to rest in the first half-cycle. The same is the case in the second half-cycle of that electron during rest to motion and motion to rest but it is under different introduction of the disappearances of forces against appearances of forces. However, at stage of levitating or gravitating period of electron, only one force is being involved at one time where the opposite force is disappeared. The uninterrupted confined inter-state electron-dynamics of atom under the availability of several bits of bit-energy results into generate forcing energy shape like a wave. Two bits of bit-energy where shape of bit for first half-cycle is like integral symbol and second half-cycle is like opposite integral symbol which are being placed along the configuring trajectory of inter-state electron-dynamics during forward-direction cycle and two bits of bit-energy shape in opposite order are being placed along the trajectory of inter-state electron-dynamics during back-direction cycle. Generating forcing energy of unit photon in each cycle is pushing to the rear side by remaining connected till the electron is not restoring the state of rest. Silicon atom is considered as a model system under neutral state. Uninterrupted confined inter-state electron-dynamics result into generate forcing energy that can travel immeasurable length and unavailability of necessitating bit-energy at any interrupted stage result into generate an overt photon. Inter-state electron-dynamics for at least two cycles generate an overt photon –a photon length twice to unit photon. Under certain interaction of unit photon, it divides equally into two bits of bit-energy instead of dividing into tits and bits of heat. The mechanism of generating photon characteristic current by the electron of neutral state atom validates that atoms are four-dimensional discs at centre of dealing no force. An isolated electron is being grounded under directed forcing energy to impinge a neutral state atom where the gained instantaneous velocity under merged energy resulting into distort atom at that point. Matter changes the role of energy and force under various sorts of interactions. Here, heat energy and photon energy explore matter at atomic and electron levels, thus, devise basis of science to describe.

The fundamental mechanism underlying negative-ion catalysis involves bond-strength breaking in the transition state (TS). Doubly-charged atomic/molecular anions are proposed as novel dynamic tunable catalysts and demonstrated in water oxidation to peroxide. Density Functional Theory TS calculations have found tunable energy activation barrier reduction ranging from 0.030 eV to 2.070eV, with Si²ˉ, Pu²ˉ, Pa²ˉ and Sn²ˉ the best catalysts; the radioactive elements usher in new application opportunities. C₆₀²ˉ reduces significantly the standard C₆₀ˉ TS energy barrier while graphene increases it, behaving like cationic systems. Rank-ordered catalysts according to their reaction barrier reduction efficiency, variation across charge states and systems reveal their tunable and wide applications, ranging from water purification to biocompatible anti-viral and anti-bacterial sanitation systems.

Group IV phospholipase A₂α (cPLA₂α) regulates the production of prostaglandins and leukotrienes via the formation of arachidonic acid from membrane phospholipids. The targeting and membrane binding of cPLA₂α to the Golgi involves the N-terminal C2 domain whereas the catalytic domain produces arachidonic acid. Although most studies of cPLA₂α concern its catalytic activity, it is also linked to homeostatic processes involving the generation of vesicles that traffic material from the Golgi to the plasma membrane. Here we investigate how membrane curvature influences the homeostatic role of cPLA₂α in vesicular trafficking. The cPLA₂α C2 domain is known to induce changes in positive membrane curvature, a process which is dependent on cPLA₂α membrane penetration. We show that cPLA₂α undergoes C2 domain-dependent oligomerization on membranes in vitro and in A549 cells. We found that the association of the cPLA₂α C2 domain with membranes is limited to membranes with positive curvature, and enhanced C2 domain oligomerization was observed on vesicles ~50 nm in diameter. We demonstrated that the cPLA₂α C2 domain generates cholesterol enriched Golgi-derived vesicles independently of cPLA₂α catalytic activity. Our results therefore provide novel insight into the molecular forces that mediate C2 domain-dependent membrane localization in vitro and in cells.

Graphene-based composites have been widely explored for electrode and electrocatalyst materials for electrochemical energy systems. In this paper, a novel composite material of the reduced graphene oxide nanosheets (rGON) with gold nanoparticles (NPs) (rGON-AuNP) is synthesized, and its morphology, structure and composition are characterized by SEM, HRTEM, XRD, EDX, FTIR, Raman, and UV-Vis techniques. To confirm this material’s electrochemical activity, a glucose oxidase (GOD) is chosen as the target reagent to modify the rGON-AuNP layer to form GOD/rGON-AuNP/glassy carbon (GC) electrode. Two pairs of distinguishable redox peaks, corresponding to the redox processes of two different conformational GOD on AuNP, are observed on the cyclic voltammograms of GOD/rGON-AuNP/GC electrode. Both cyclic voltammetry and electrochemical impedance spectroscopy are employed to study the mechanism of direct electron transfer from GOD to GC electrode on the rGON-AuNP layer. In addition, this GOD/rGON-AuNP/GC electrode shows catalytic activity toward glucose oxidation reaction.

Real-time evolution of the electron densities under excitations in La₂CuO₄ was calculated by the time-dependent density functional theory (TDDFT). The author found, for the first time, under excitations, the electron cloud of Cu²⁺ changes obviously and the characteristic frequencies are 83 meV and 36 meV, respectively, for two different modes. The results are unexpected and close to that of lattice vibrations. The results show that the electron cloud of Cu²⁺ (just like the lattice) can be the electron-pairing medium in high temperature copper oxide superconductors.

Electron Channeling Contrast Imaging (ECCI) is becoming a powerful tool in Materials Science for characterizing deformation defects. Dislocations observed by ECCI in Scanning Electron Microscope, exhibit several features depending on the crystal orientation relative to the incident beam (white/black line on a dark/bright background). In order to bring new insights concerning these contrasts, we report an original theoretical approach based on the dynamical diffraction theory. Our calculations led, for the first time, to an explicit formulation of the backscattered intensity as a function of various physical and practical parameters governing the experiment. Intensity profiles are modeled for dislocations parallel to the sample surface for different channeling conditions. All theoretical predictions are consistent with experimental results.

Equiatomic CuZr alloy undergoes a martensitic transformation from the B2 parent phase to martensitic phases (P21/m and Cm) below 150 °C. We clarified the effect of the thermal cycling on the morphology and crystallography of martensite in equiatomic CuZr alloy using a transmission electron microscopy. The 10th cycled specimens consisted of different multiple structures at the maximum temperature of DSC measurement: 400 °C and 500°C, respectively. At the maximum temperature 400 °C of DSC measurement, it is composed of the fine plate-like variants, and a lamellar eutectoid structure consisting of Cu10Zr7 and CuZr2 phases on the martensitic variant. Concerning the maximum temperature 500 °C of DSC measurement, it is observed the martensitic structure and the lamellar structure in which the martensitic phase was completely eutectoid transformed. The formation of this lamellar eutectoid structure due to thermal cycling leads to the shift of forward and reverse transformation peaks to low and high temperature side. In addition, new forward and reverse transformation peaks indicating a new transformation appeared by thermal cycling, and the peaks remained around -20 °C. This new martensitic transformation behavior is also discussed.

This study characterizes the microstructure and its associated crystallographic features of bulk maraging steels fabricated by selective laser melting (SLM) combined with a powder bed technique. The fabricated sample exhibited characteristic melt pools in which the regions had locally melted and rapidly solidified. A major part of these melt pools corresponded with the ferrite (alpha) matrix, which exhibited a lath martensite structure with a high density of dislocations. A number of fine retained austenite (gamma) with a <001> orientation along the build direction was often localized around the melt pool boundaries. The orientation relationship of these fine gamma grains with respect to the adjacent alpha grains in the martensite structure was (111) gamma // (011) alpha and [-101] gamma // [-1-11] apha (Kurdjumov–Sachs orientation relationship). Using the obtained results, we inferred the microstructure development of maraging steels during the SLM process. The results depict that new and diverse high-strength materials can be used to develop industrial molds and dies.

Some studies have demonstrated that in vivo degradation processes are influenced by the material’s physico-chemical properties. The present study compares two hydroxyapatites manufactured on an industrial scale, deproteinized at low and high temperatures, and how physico-chemical properties can influence the mineral degradation process of material performance in bone biopsies retrieved 6 months after maxillary sinus augmentation. Residual biomaterial particles were examined by field scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) to determine the composition and degree of degradation of the bone graft substitute material. According to the EDX analysis, the Ca/P ratio significantly lowered in the residual biomaterial (1.08±0.32) compared to the initial composition (2.22±0.08) for the low-temperature sintered group, which also presented high porosity, low crystallinity, low density, a large surface area, and poor stability and a high resorption rate compared to the high-temperature sintered material. This demonstrates that variations in the physico-chemical properties of bone substitute material clearly influence the degradation process. Further studies are needed to determine whether the resorption of deproteinized bone particles proceeds slowly enough to allow sufficient time for bone maturation to occur.

Biohydrogen is a versatile energy carrier for the generation of electric energy from renewable sources. Hydrogenases can be used in enzymatic fuel cells to oxidize dihydrogen. The rate of electron transfer (ET) at the anodic side between the [NiFe]-hydrogenase enzyme distal iron-sulfur cluster and the electrode surface can be described by the Marcus equation. All parameters for the Marcus equation are accessible from DFT calculations. The distal cubane FeS-cluster has a three cysteine and one histidine coordination [Fe₄S₄](His)(Cys)₃ first ligation sphere. The reorganization energy (inner- and outer-sphere) is almost unchanged upon a histidine-to-cysteine substitution. Differences in rates of electron transfer between the wild-type enzyme and the all-cysteine mutant can be rationalized by a diminished electronic coupling between the donor and acceptor molecules in the [Fe₄S₄](Cys)₄ case. The fast and efficient electron transfer from the distal iron-sulfur cluster is realized by a fine-tuned protein environment which facilitates the flow of electrons. This study enables the design and control of electron transfer rates and pathways by protein engineering.

The Lower Mekong Basin has had extensive hydropower dam development, which changes hydrologic conditions and threatens the exceptional aquatic biodiver-sity. This study quantifies the degree of hydrologic change between pre-impact (1965-1968) and post-impact (2018-2021) peak hydropower development in two major tributaries of the Lower Mekong Basin, the Sekong River with the fewest dams and the Sesan River with the most dams. Both rivers historically supported migratory fishes. We use daily pre- and post-impact data and the Indicators of Hydrologic Alteration framework to evaluate streamflow changes from dam development. We found signifi-cant changes in low and high magnitude flows in the pre- and post-impact periods of dam development. For the Sekong River, minimum flow had large fluctuations that ranged 290% to 412% more than the pre-impact period, while the Sesan River ranged 120% to 160% more than pre-impact. Dry season flows increased by 200±63% on av-erage in the Sekong River, which is caused by releases from upstream dams. Mean-while, Sesan River dry season flows increased by 100±55% on average. This study in-dicates that seasonal flow changes and extreme flow events occurred more frequently in the two basins following dam construction, which may threaten the ecosystem func-tions.

Membrane gas absorption technology has been considered as a promising approach to mitigate CO2 emissions from power plants. The aim of this study is to evaluate the environmental impacts of CO2 absorption and desorption processes by hollow fiber membrane contactors using life cycle assessment methodology. On the basis of ReCipe 2016 Midpoint and ReCipe 2016 Endpoint methods, the research results show that, membrane gas absorption system exhibits the lowest environmental impacts across the majority assessed categories in comparison with chemical absorption and membrane gas separation systems. The CO2 capture process via membrane gas absorption has the most significant impact on METP category, with heat consumption as the primary contributing factor accounting for 55%, followed by electricity consumption accounting for 43.1%. According to the sensitivity analysis, heating by natural gas shows a better performance than other heat supply sources in improving overall environmental impacts. In addition, the increasing utilization of renewable energy in electricity supply reduces the global warming potential, fossil resource consumption and ozone formation.

The growing urgency for sustainable energy solutions necessitates a deeper understanding of the environmental impacts of renewable technologies. This article aims to synthesize and analyze Life Cycle Assessments (LCA) in this domain, providing a comprehensive perspective. We systematically categorize 2,923 articles into four communities: (1) Photovoltaic systems, (2) Wind energy systems, (3) Materials for auxiliary industry of photovoltaic and wind systems, and (4) Solar thermal systems. A comparative analysis is conducted to identify methodological consistencies and disparities across these communities. The findings reveal diverse methodological approaches and a range of environmental impacts, highlighting the complexities in assessing renewable energy systems. The article underscores the significance of material selection in photovoltaic and wind systems, providing a critical overview of the current state of LCA research in renewable energy and stressing the need for standardized methodologies. It also identifies gaps in recent research, offering insights for future studies focused on integrating environmental, economic, and social considerations in renewable energy assessments.As a case study, an LCA was used to evaluate two energy supply methods for a sensor network: one connected to the public grid and another powered by a photovoltaic panel. The off-grid system, while more environmentally friendly by reducing reliance on non-renewable energy sources, posed challenges due to the high environmental impact of battery production and disposal. Integrating environmental assessments provides a robust framework for making informed decisions on sustainable technologies. The findings are critical for projects that balance technological needs with sustainability goals.

This paper aims to provide an evaluation of how Value Added Tax (VAT) policy alterations influence market liquidity, trading volume, and stock performance. To fill the existing literature gap on the direct effect of (VAT) adjustments on stock market dynamic, particulate within the banking industry. The study employs an event study methodology to analyse the immediate and medium-term effects on bank stocks listed in markets subject to a (VAT) adjustments. The core of the study analysis is anchored around two pivotal events, the initial application of (VAT) on 1st January 2018, and the subsequent (VAT) increase to 15% on 1st July 2020 using MATLAB R2022b. The study analysis encompasses the period immediately before and after the introduction and subsequent increase (VAT) in kingdom Saudi Ariba (KSA) employing an eleven sample comprises the (KSA) largest banks with a ±7 days window period from the event. The analysis revels that the imposition of 5% (VAT) lead a substation downturn in trading volume and stock returns of 9.5%, and 39.5%, subsequently. While when the (VAT) was increased by 15% the market exhibited a mixed but ultimately positive response of 3.3% trading volumes increases and 128.7% average stock return recovery.

Emergence of COVID-19 had profound impact on global stock markets, including Indian mar-ket. Key indices like NIFTY50 and Sensex dropped by approximately 40% within two months in 2020, which also affected major mutual funds, leading to significant depreciation of their Net Asset Value. Securities and Exchange Board of India (SEBI) allows mutual funds to use deriva-tives for hedging purposes, capped at 100% of the scheme's net assets covering debt, equity, and derivatives. However, circular amendment by SEBI in January-2019 permitted covered call strat-egies on constituent stocks of Sensex and NIFTY50 for mutual fund schemes, excluding ETFs and Index Funds. This study investigated whether mutual funds increased their derivative us-age as risk mitigation strategy during COVID-19 pandemic, analyzing derivative holdings from 2019-2023. Surprisingly, findings indicated a decline in derivative holdings in 2020 compared to pre-pandemic levels. Statistical tests and performance evaluation metrics such as T-test, F-test, Treynor Ratio, Sharpe Ratio, and Jensen's calculations were employed to assess mutual fund performance. Although derivative-holding mutual funds didn't outperform benchmarks in aver-age returns, it showcased significantly reduced volatility, offering investors favorable risk-return trade-offs. research sheds light on derivative utilization in Mutual Fund industry, potentially in-forming regulators, fund managers, and investors in their decision-making

This paper undertakes a comprehensive review to underscore the central role of sustainability in the evaluation and innovation of jet grouting technologies. It meticulously traces the evolution of evaluation methodologies, emphasizing the imperative of sustainable practices throughout history. Traditional evaluation paradigms are examined alongside contemporary trends, with a particular focus on sustainability metrics and visualization techniques. Through an examination of innovative jet grouting technologies, this paper illustrates how sustainability principles have driven advancements aimed at improving the efficiency and environmental impact of jet grouting methods. Central to this review is an assessment of sustainability across multiple dimensions, including method applicability, installation and operational compatibility, and the performance of the resulting jet grouted piles. By emphasizing sustainability considerations, the paper highlights the intrinsic link between environmental integrity and technological innovation in the field of jet grouting. In addition, it discusses analytical evaluation methods designed to proactively address sustainability concerns prior to construction, thereby promoting a more environmentally responsible approach. Finally, this paper presents a pioneering evaluation framework that integrates real-time monitoring and visualization tools, allowing stakeholders to track sustainability milestones throughout the construction process. By emphasizing sustainability as a guiding principle, this review advocates for a paradigm shift toward more ecologically sound and resilient jet grouting practices.

Quantifying different stocking rates effects in three study areas placed at Mediterranean forest (Cuenca, Spain) was conducted by applying a multiparametric soil quality index, SQI, developed in undisturbed forest soils (> 40 years). The main objective is to advance in the development and application of multiparametric indexes which allow for soil condition assessment. For it, is analyse the effectiveness of a multiparametric soil quality index (SQI) as an indicator livestock impacts on the soil in mediterranean forests. Control areas without stocking rates were compared in forest stands with different age (Thicket forest stand, < 30 years; High polewood forest stand, 30-60 years; Old growth forest stand, > 60 years); with various intensity grazing areas (permanent livestock passage: inactive sheepfold for 2-3 years, and active sheepfold; intermittent livestock passage: bare soil, pine stand, scrubland). The multiparametric soil quality index (SQI) applied sensitive to changes in forest ecosystems depending of different stocking rates. However, for even more preci-sion to assess cattle alteration, multiparameter index recalibrated, creating a new one; Soil Status Index by Livestock (SSIL). Correlation between quality ranges obtained with both indexes in dif-ferent study areas suggest that SSIL can be considered a livestock impact reference indicator in Mediterranean forest soils.

Heavy metal pollution poses a significant threat to global populations, particularly impacting human health. Developing countries, characterized by chemical engineering and mining industrial activities, often contribute to diverse heavy metal contaminants. Consumption of water contaminated with heavy metals, prevalent in such regions, can lead to severe health risks, including gastric cancer. Addressing the urgent issue of heavy metal pollution, this paper employs a bibliographic approach to explore the latest literature on heavy metal pollution. The study discusses recent research findings and potential methods for the treatment and mitigation of heavy metal pollution, emphasizing the pressing need for effective solutions to safeguard public health.

This research investigates the fatigue crack propagation on the lower surface of rocket deflector troughs of offshore rocket launch platforms. Initially, a numerical model of the offshore rocket launch platform is established using ABAQUS based on the Extended Finite Element Method (XFEM). Subsequently, two variable parameters—namely, the initial crack length and initial tilt angle—are introduced. This research systematically analyzes the impact of these parameters on fatigue crack propagation patterns in both the maximum stress and maximum deformation regions of the deflector channels under the combined conditions of high temperature and impact. Finally, the research indicates that the propagation length of surface cracks in the deflector trough exhibits a trend of initial increase followed by a subsequent decrease with the increase in the preset inclination angle. Notably, the stable propagation rate of the crack in the region of maximum deformation surpasses that observed in the region of maximum stress. Through meticulous comparative analysis, it is evident that temperature loading significantly fosters the initiation and propagation of cracks, particularly in the upper region of the deflector channel's lower surface.

This review explores the transformative impact of sensor technologies in early disease detection. It highlights recent advancements in nanotechnology-based sensors, particularly focusing on their applications in identifying disease biomarkers at early stages. The integration of these sensors with artificial intelligence for predictive analytics in healthcare is also discussed. Applications in cancer, infectious diseases, and chronic disease management underscore their diverse utility. Challenges in sensor technology adoption and future directions, including multiplexed sensors and wearable devices, are examined. This review underscores sensors' potential in enhancing disease management and patient outcomes.

Microplastic contamination, defined as plastic particles less than 5 mm in size, has become a major global environmental concern. This study synthesizes findings from carefully chosen studies undertaken in a variety of geographical areas and ecosystems, offering light on the multifaceted issues posed by microplastic pollution. These articles show the global prevalence of microplastics in both land and marine ecosystems. Seasonal fluctuations in microplastic abundance highlight the cyclical nature of this pollution, with larger amounts being reported during the summer months. Tourism, industrialization, and urbanization have all been highlighted as significant contributors to microplastic contamination, stressing the impact of man-made influences. Wastewater treatment plants (WWTPs) have been identified as hotspots for microplastic release into aquatic habitats, emphasizing the need for enhanced treatment procedures. Because microplastics can build up in the food chain, it underlines the possible health problems connected with microplastic pollution for both aquatic creatures and human consumers. Longitudinal studies, geographical variety, in-depth health and ecological impact evaluations, standardization, and effective mitigation methods should be prioritized in future studies. To address this worldwide issue, interdisciplinary collaboration among scientists, health professionals, politicians, and industrial stakeholders is required.

The broad and rapid application of new genomic techniques (NGTs) such as CRISPR-Cas has led to a fast increase in the number of genetically modified crops. With the recently published EU Commission’s (EC) regulatory proposal on plants generated with NGTs (July 5, 2023) the process of admission of such genetically modified plants is aimed to get accelerated and simplified. NGT plant applications shall be categorized based on their molecular characteristics into category 1 NGT (NGT1) and category 2 NGT (NGT2), which is in divergence from the current legislation centered around Directive 2001/18/EC. In the regulatory proposal NGT2 plants are envisioned to undergo a reduced risk assessment while for NGT1 plants no risk assessment is foreseen at all. To demonstrate were the path of the proposal leads to in practice, we applied the proposed criteria for categorization to a list of NGT plant applications that are currently in the commercialization pipeline. A key finding is that out of those plant applications affected by the EC proposal, 94% would be classified as NGT1 and thus would receive a market approval without risk assessment, monitoring and sufficient labeling provisions. The remaining 6% of applications would be classified as NGT2 plants for which, in deviation from the current regulation, an adapted risk assessment is proposed. A screening of intended traits in the pipeline highlights that certain NGT1 plants can pose similar environmental risks (e.g. invasiveness) compared to other genetically modified organisms (GMOs), as defined in Directive 2001/18/EC. For example, NGT1 applications based on RNAi technology can exhibit insecticidal effects with potential side effects on non-target organisms (i.e. other insects). Our quantitative and case-specific elaboration on how the current EC regulatory proposal would affect the environment, health or consumer protection will be informative for decision makers and politicians.

In many ports, the ship's speed is limited for the safety of navigation. At the same time, ship captains and port pilots choose the speed of the ship, but not higher than the permitted speed of the ship in the port, therefore the speed of the ship also depends on the experience of the ship captains and port pilots and the sailing conditions of the ship in specific conditions. Choosing the optimal speed of ships in port, including the effect of shallow depth, can reduce fuel consumption and ship emissions in ports, which is important for the development of green and sustainable ports. In all cases, shipping safety is the highest priority. The main objectives of the article are determining the optimal speed of ships in ports with low clearance, ensuring navigational safety, reducing fuel consumption and emissions, and at the same time creating a sustainable port. The article presents the methodology of optimal ship speed calculation, minimum ship controllable speed maintenance, fuel consumption and emission reduction methodology and their impact on sustainable and green maritime transport and port development. The developed methodology was tested on real ships and with the help of a calibrated simulator, sailing through harbor channels and harbor waters in low clearance conditions.