The gravel road pavement has a lower construction cost but poorer performance than the asphalt surface. It also emits dust and deforms under the impact of vehicle loads and ambient air factors. The resulting ripples and ruts are constantly deepening, increasing vehicle vibrations and fuel consumption, reducing safe driving speed and comfort. In this article, existing pavement quality evaluation indexes are analysed, and a methodology for their adaptation for roads with gravel pavement is proposed. This article reports the measured wave depth and length of the gravel pavement profile by the straightedge method of a 160 m long road section in three road exploitation stages. The measured pavement elevation was processed according to ISO 8608, and vehicle frequency response has been investigated using simulations in MATLAB/Simulink. The applied International Roughness Index (IRI) analysis showed that a speed of 30-45 km/h instead of 80 km/h provides the objective results of IRI calculation on the flexible pavement due to a decreasing velocity of vehicle's unsprung mass on a more deteriorated road pavement state. The influence of the corrugation phenomenon of gravel pavement has been explored, identifying specific driving safety and comfort cases. Finally, an increase in the Dynamic Load Coefficient (DLC) at a low speed of 30 km/h on the most deteriorated pavement and a high speed of 90 km/h on the middle-quality pavement demonstrates the demand for timely gravel pavement maintenance and the complicated prediction of a safe driving speed for drivers.

We introduce a number of techniques in quantitative convergent-beam electron diffraction under development by our group and discuss the basis for measuring interatomic electrostatic potentials (and therefore also electron densities), localised at sub-nanometre scales, with sufficient accuracy and precision to map chemical bonds in and around nanostructures in nanostructured materials. This has never before been possible as experimental measurements of bonding in quantum crystallography have hitherto always been restricted to homogeneous single-phased crystals.

This paper describes the packaging models that are fundamental for the design of ultra-high-performance concrete (UHPC), and their evolution. They are divided into two large groups: continuous and discrete models. The latter are those that provide the best answer in obtaining an adequate simulation of the packing of the particles up to nanometric size. This includes the interaction among the particles by means of loosening and wall coefficients, allowing a simulation of the virtual and real compactness of such particles. In addition, a relationship between virtual and real compactness is obtained, through the compaction index, which may simulate the energy of compaction that the particles undergo in their placement in the mold. The use of last-generation additives allows such models to be implemented with water-cement (w/c) ratios close to 0.18. However, the premise of maximum packing as a basic pillar for the production of UHPC should not be the only one. The cement hydration process affected by nanoadditions and the ensuing effectiveness in the properties in both fresh and hardened state according to the respective percentages in the mixture should also be studied. An adequate ratio and proportion of these additions may lead to an obtaining of better results even with lower levels of compactness.

Microbiome research has gained considerable interest due to the emerging evidence of its impact on human and animal health. Similar to higher organisms, the gut-associated microbiota of mosquitoes affect host fitness and other phenotypes. It is now well established that microbes can alter pathogen transmission in mosquitoes, either positively or negatively, and avenues are being explored to exploit microbes for vector control. However, less attention has been paid to how microbiota affect phenotypes that impact vectorial capacity. Several mosquito and pathogen components, such as vector density, biting rate, survival, vector competence and pathogen extrinsic incubation period all influence pathogen transmission. Interestingly, the mosquito gut-associated microbes can impact each of these components, and therefore ultimately modulate vectorial capacity. Promisingly, this expands the options available to exploit microbes for vector control by also targeting parameters that affect vectorial capacity. However, there are still many knowledge gaps in the biology of the mosquito – microbe symbiosis that need to be addressed in order to understand these interactions more thoroughly and exploit them efficiently. Here, we review current evidence of the impacts of the microbiome on aspects of vectorial capacity highlighting opportunities for novel vector control strategies and areas where further studies are required.

The fluorine-less noble-gas containing anions OBONgO- and OCNNgO-have been studied by correlated electronic structure calculation and density functional theory. The obtained energetics indicates that for Ng = Kr and Xe, these anions should be kinetically stable at low temperature. The molecular structures and electron density distribution suggests that these anions are stabilized by ion-induced dipole interactions with charges concentrated on the electronegative OBO and OCN groups. The current study shows that in additional to the fluoride ion, polyatomic groups with strong electronic affinities can also form stable noble-gas containing anions of the type X-...NgO.

Learning disorders (LD) are diagnosed in children whose academic skills of reading, writing or mathematics are impaired and lagged according to their age, schooling and intelligence. Children with LD experience substantial working memory (WM) deficits, even more pronounced if more than one of the academic skills is affected. We compared the task-related EEG power spectral density of children with LD (n= 23), with a control group of children with good academic achievement (n= 22), during the performance of a WM task. sLoreta was used to estimate the current distribution at the sources, and 18 brain regions of interests (ROIs) were chosen with an extended version of the eigenvector centrality mapping technique. In this way, we lessen some drawbacks of the traditional EEG at the sensor space by an analysis at the brain sources level over data-driven selected ROIs. Results: The LD group showed fewer correct responses at the WM task, an overall slower EEG with more theta activity in all ROIs, less upper-alpha power at posterior areas, and less high-frequency beta activity in frontal areas. We explain these EEG patterns in LD children as indices of an inefficient neural resource management related with a delay in the neural development.

Spiral galaxies and their rotation curves have key characteristics of differentially spinning objects. Oblate spheroid shapes are a consequence of spin and reasonably describe galaxies, indicating that their matter is distributed in gravitationally interacting homeoidal shells. Previously published equations describing differentially spinning oblate spheroids with radially varying density are here applied to 51 galaxies, mostly spirals. A constant volumetric density (rho, kg m-3) is assumed for each thin homeoid in these formulae, after Newton, which is consistent with RC being reported simply as a function of equatorial radius r. We construct parameter-free inverse models that uniquely specify mass inside any given r, and thus directly constrain rho vs. r solely from velocity v(r) and galactic aspect ratios (assumed as 1:10 when data are unavailable). Except for their innermost zones, rho is proven to be closely proportional to rn, where n for all 36 spirals studied equals -1.80±0.40. Our values for interior densities compare closely with independently measured baryon density in appropriate astronomical environments: for example, calculated rho at galactic edges agrees with estimated rho of intergalactic media (IGM). Our finding that central densities increase with galaxy size is consistent with behavior exhibited by diverse self-gravitating entities. Our calculated mass distributions are consistent with visible luminosity and require no non-baryonic component. Empirical luminosity-velocity relationships for galaxies, such as the Tully-Fisher rule, originate in Newtonian physics.

We present a uniform method of density elimination for several semilinear substructural logics. Especially, the density elimination for the involutive uninorm logic IUL is proved. Then the standard completeness of IUL follows as a lemma by virtue of previous work by Metcalfe and Montagna.

In this paper we establish some weighted integral inequalities of Ostrowski, Čebyšev and Lupaş type. Applications for continuous probability density functions supported on infinite intervals with two examples are also given.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Recently, due to the decrease in labor force, increase in labor costs, and the desire for improved quality of life, research on robots has been actively conducted to address these issues. However, it is currently difficult to find robots that physically interact with humans. The reason is that the actuators of robots do not have high torque density on their own. To solve this problem, high torque density motors, such as proprioceptive actuators, are being researched. However, the torque density is still insufficient for physical interaction with humans, so we have developed a motor with higher torque density. However, high torque density motors have the disadvantage of lower speed characteristics due to increased Back-EMF. Therefore, to address the deterioration of speed characteristics in the developed motor, we applied the Independent 3-Phase winding structure to improve the speed characteristics. Consequently, through comparison with Y-Connection and Delta-Connection, we propose the most suitable winding structure for high torque density motors intended for physical interaction with humans.

Background: Diabetes mellitus (DM) and osteoporosis are two of the most widespread metabolic disease in the world. The aim of this study is to investigate the prevalence of DM among patients affected by osteoporosis and fragility fractures, and to search differences in clinical features. Methods: 713 patients belonging to CTO Bone Unit because of osteoporosis and fragility fractures were divided into two groups, according to the diagnosis of DM. The clinical and bone characteristics of patients were compared. Results: Prevalence of DM was 10.8%. When compared to patients without DM, the median age at the time of first fracture was similar (72 years ± 14 IQR vs 71 years ± 12 IQR); prevalence of combination of vertebral and hip fractures was higher (p=0.039), as well as prevalence of males, although not significantly (p=0.051). Bone mineral density (BMD) at all sites was higher in DM group; Trabecular Bone Score (TBS), instead, was significantly lower (p<0.001). Conclusions: Patients with fragility fractures and DM more frequently show combination of major fractures with higher BMD levels. In these patients, TBS could be a better indicator of bone health than BMD and therefore should be used as a diagnostic tool in clinical practice.

The current investigation presents porous ceramic materials prepared of cenospheres prepared by spark plasma sintering. The impact of sintering temperature, mould diameter (20 and 30 mm diameter) and cenosphere size on the properties of the sintered material was investigated. Shrinkage of the samples during sintering started at 900 °C. Sample shrinkage during sintering increases with increasing temperature and decreases with increasing mould size; increasing sample sintering temperature increases the apparent density of all sample series CS 63-150 µm in 20 mm mould from 0.97 to 2.3 g·cm-3 at 1050 - 1300 °C, in 30 mm mould 0.81 - 1.87 g·cm-3 at 1050 - 1200 °C, in 50 mm mould 0.54 - 0.75 g·cm-3 at 1050 - 1150 °C, while CS 150-250 µm in 20 mm mould 0.93 - 1.96 g·cm-3 at 1050 - 1200 °C. Total porosity decreases from 61.5% to 3.9% with increasing sintering temperature from 1050 to 1250 °C, while open porosity reduces at lower temperatures, with closed porosity being highest in samples sintered at 1150 °C. When the sintering temperature increases from 1050 to 1300 °C, the compressive strength of the CS 63-150 samples produced in a 20 mm mould increases from 11 MPa to 312 MPa. These results correlate with the Rice model, which describes an exponential dependence of compressive strength on material porosity and fully dense material compressive strength.

NiO-based nanomaterials have attracted a great deal of interest in view of various applications, that have stimulated the implementation of various synthetic approaches to control their chemico-physical properties as a function of the desired end-use. In this regard, their bottom-up preparation starting from suitable precursors plays an important role, but a molecular level in-sight into their reactivity remains an open challenge. In this study, we focus on the fragmentation of Ni(II) diketonate-diamine adducts, of interest as precursors for Ni(II) oxide systems, by com-bined electrospray ionization mass spectrometry (ESI-MS) with multiple collisional experiments (ESI-MSn) and theoretical calculations. The joint analyses revealed common features in the frag-mentation pattern of the target compounds: i) in the first-fragmentation, all three complexes form analogous base-peak cations by losing a negatively charged diketonate; in these cations, Ni-O and Ni-N interactions are stronger and the Ni positive charge is lower than in the neutral complexes; ii) the tendency of ligand electronic charge to migrate towards Ni further increases in the subsequent fragmentation processes, leading to the formation – in all three cases – of a tetracoordinated Ni environment involving an interesting cation-π intramolecular interaction.

Support effect is an important issue in heterogeneous catalysis while the explicit role of a catalytic support is often unclear for catalytic reactions. A systematic density functional theory computational study is reported in this paper to elucidate the effect of a model boron nitride (BN) support on the first N-H bond activation step of NH3 on Run (n =1, 2, 3) metal clusters. Geometry optimizations and energy calculations were carried out using density functional theory (DFT) calculation for intermediates and transition state from the starting materials undergoing the N-H activation process. The primary findings are summarized as follows. The involvement of the model BN support does not significantly alter the equilibrium structure of intermediates and transition state in the most favorable pathway (MFP). Moreover, the involvement of BN support decreases the free energy of activation, ΔG≠, thus improving the reaction rate constant. This improvement is more obvious at high temperatures like 673 K than low temperatures like 298 K. The BN support effect leading to the ΔG≠ decrease is most significant for the single Ru atom case among all three cases studied. Finally, the involvement of model BN may change the spin transition behavior of the reaction system during the N-H bond activation process. All these findings provide a deeper insight into the support effect on the N-H bond activation of NH3 for supported Ru catalyst in particular and for supported transition metal catalysts in general.

We discuss the neutron skins of 48Ca and 208Pb. We review and critically examine modern predictions and empirical constraints, with special attention to the dierent interpretations of the ndings from the PREX-II experiment and the recently reported value of the neutron skin in 48Ca extracted from the CREX experiment. We argue that, in the spirit of the ab initio philosophy, the path to understanding the behavior of dense neutron-rich matter must not circumvent fundamental nuclear forces. Based only on that argument, a thick neutron skin in 208Pb is highly unlikely.

The redox properties of quinones underlie their unique characteristics as organic battery components that outperform the conventional inorganic ones. Furthermore, the redox properties could be precisely shaped by using different substituent groups. Machine learning and statistics, onthe other hand, have proven to be very powerful approaches for efficient in silico design of novel materials. Herein, we demonstrated the machine learning approach for the prediction of the redox activity of quinones that potentially can serve as organic battery components. For the needs of the present study, a database of small quinone-derived molecules was created. A large number of quantum chemical and chemometrics descriptors was generated for each molecule and subsequently different statistical approaches were applied to select the descriptors that most prominently characterize the relationship between structure and redox-potential. Various machine-learning methods for screening of prospective organic battery electrode materials were deployed to select the most trustworthy strategy for machine learning aided design of organic redox materials. It was found that ridge regression models perform better than regression decision tree and decision tree based ensemble algorithms.

Based on the Generalized bracket, or Beris-Edwards, formalism of non-equilibrium thermodynamics, we have recently proposed [Stephanou et al. Materials, 13, 2867 (2020)] a new differential constitutive model for the rheology of entangled polymer melts and solutions. It has amended the shortcomings of a previous model that was too strict in the values of the convective constraint release parameter for the model not to violate the second law of thermodynamics and has been shown capable of predicting a transient stress undershoot (following the overshoot) at high shear rates. In this work, we wish to further examine this model’s capability of predicting the rheological response of industrial polymer systems by extending it to its multiple-mode version. The comparison against industrial rheological data (High-Density Polyethylene resins), as compared against available experimental data in (a) Small Amplitude Oscillatory shear, (b) start-up shear, and (c) start-up uniaxial elongation, is noted to be good.

Although many policosanols from different sources, such as sugar cane, rice bran, and insects, have been marketed worldwide, there has been no comparative study of the in vivo efficacy using a hyperlipidemic animal model. This study compared the efficacy of treating dyslipidemia with four different policosanols, including one sugar cane wax alcohol from Cuba (Raydel®) and three policosanols from China (Xi’an Natural sugar cane, Xi’an Realin sugar cane, and Shaanxi rice bran) in hyperlipidemic zebrafish. After 12 weeks of consumption of each policosanol (final 0.1% in diet, wt/wt) and high cholesterol diet (HCD, final 4%, wt/wt) in a tetrabit, the Raydel policosanol group and Xi’an Natural policosanol group showed the highest survivability of approximately 81%, whereas the Xi’an Realin policosanol group and Shaanxi policosanol group showed 57% and 67% survivability, respectively. Among five HCD groups, the Raydel policosanol group showed the lowest serum total cholesterol (TC, p<0.001 versus HCD control) and triglyceride (TG, p<0.001 versus HCD control) with the highest percentage of high-density lipoproteins (HDL)-C in TC. The Raydel policosanol group also showed the lowest serum aspartate aminotransferase (AST) and alanine aminotransferase (ALT) levels with the least infiltration of inflammatory cells and interleukin-6 production in hepatocytes. In the ovary, the Raydel policosanol group also showed the highest contents of mature vitellogenic oocytes with the lowest production of reactive oxygen species and cellular apoptosis in ovarian cells. In the testis, the Raydel policosanol group also showed the healthiest morphology for spermatogenesis with the least interstitial area and reactive oxygen species (ROS) production in testicular cells. In conclusion, 12 weeks of Raydel policosanol consumption resulted in remarkable improvement of the blood lipid profile, amelioration of inflammation in the liver, and enhancement of the cell morphology in the ovary and testis with the highest survivability under the HCD.

In swarm-robotics foraging, the purpose of task allocation is to adjust the number of active foraging robots dynamically based on the task demands and changing environment. It is a difficult challenge to generate self-organized foraging behavior in which each robot can adapt to environmental changes. To complete the foraging task efficiently, this paper presents a novel self-organized task allocation strategy known as the dynamic response threshold model (DRTM). To adjust the behavior of the active foraging robots, the proposed DRTM newly introduces the traffic flow density, which can be used to evaluate the robot density. First, the traffic flow density and the amount of obstacle avoidance are used to adjust the threshold which determines the tendency of a robot to respond to a stimulus in the environment. Then, each individual robot uses the threshold and external stimulus to calculate the foraging probability that determines whether or not to go foraging. Simulation and physical experiments are carried out to evaluate the performance of the proposed method. The experimental results show that the DRTM is superior to and more efficient than the adaptive response threshold model (ARTM) in swarm foraging.

new subsonic blower wind tunnel design has been studied both numerically and experimentally, it is also referred to as “blower” wind tunnel. This paper, is initially aimed to address each sequential stage of the wind tunnel design process. Rather than applying the standard method of modelling solely the flow in the test section, a large-scale CFD model of the whole wind tunnel was employed. The loss of every constituent element was calculated and then all the losses are added up to determine the power needed for the wind tunnel operation which is used as “intake fan” boundary conditions in the CFD model. Then, flow uniformity and turbulent intensity measurements in an empty test section using a Pitot-static tube and hot wire anemometer (HWA) were introduced to validate the CFD results. The results showed that flow quality was significantly affected by boundary layer controllers (honeycomb and mesh screens) in the settling chamber and wide-angle diffuser. Investigations were also conducted to evaluate the flow deficit in the wake area behind a convex hump model using HWA. This was additional experimental tests carried out to validate the suitability of the wind tunnel flow aerodynamic research.

We construct a novel family of summation-integral type hybrid operators in terms of shape parameter $\alpha\in \lbrack 0,1]$ in this paper. Basic estimates, rate of convergence, and order of approximation are also studied using the Korovkin theorem and the modulus of smoothness. We investigate the local approximation findings for these sequences of positive linear operators utilising Peetre's K-functional, Lipschitz class, and second-order modulus of smoothness.

Recent expansion in data sharing has created unprecedented opportunities to explore structure-function linkages in ecosystems across spatial and temporal scales. However, characteristics of the same data product, such as resolution, can change over time or spatial locations, as protocols are adapted to new technology or conditions, which may impact the data’s potential utility and accuracy for addressing end user scientific questions. The National Ecological Observatory Network (NEON) provides data products for users from 81 sites and over a planned 30-year time frame, including discrete return Light Detection and Range (LiDAR) from an airborne observatory platform. LiDAR is a well-established and increasingly available remote sensing technology for measuring three-dimensional (3D) characteristics of ecosystem and landscape structure, including forest structural diversity. The LiDAR product that NEON provides can vary in point density from 2 – 25+ points/m² depending on instrument and acquisition date. We used NEON LiDAR from five forested sites to (1) identify the minimum point density at which structural diversity metrics can be robustly estimated across forested sites from different ecoclimatic zones in the USA and (2) to test the effects of variable point density on the estimation of a suite of structural diversity metrics and multivariate structural complexity types within and across forested sites. Twelve out of sixteen structural diversity metrics were sensitive to LiDAR point density in at least one of the five NEON forested sites. The minimum point density to reliably estimate the metrics ranged from 2.0 to 7.5 pt/m^2, but our results indicate that point densities above 7-8 pt/m² should provide robust measurements of structural diversity in forests for temporal or spatial comparisons. The delineation of multivariate structural complexity types from a suite of 16 structural diversity metrics was robust within sites and across forest types for a LiDAR point density of 4 pt/m² and above. This study shows that different metrics of structural diversity can vary in their sensitivity to the resolution of LiDAR data and users of these open-source data products should consider the point density of their data and use caution in metric selection when making spatial or temporal comparisons from these datasets.

One of the intriguing recent results in the field of high-entropy alloys is the discovery of single-phase equiatomic multi-component Laves intermetallics. However, there is no clear understanding that a combination of chemical elements will form such high-entropy compounds. Here we contribute to understanding this issue by modifying the composition of duodenary TiZrHfNbVCrMoMnFeCoNiAl (12x) alloy in which we recently reported the fabrication of hexagonal C14 Laves phase. We consider three alloys based on 12x: 7x=12x-VCrMoMnFe, 12x+Sc, 12x+Be and observe that all of them crystalize with the formation of C14 Laves phase as a dominant structure. We report that 12x+Be alloy reveals single-phase C14 structure with very high concentration of structural defects and ultra-fine dendritic microstructure with almost homogenous distribution of the constituted elements over the alloy matrix. The 7x and 12x+Sc alloys contain C14 as a main phase and unknown impurity phases. To characterize the materials, we examine their heat capacity, electrical conductivity and magnetic properties. The measurements reveal that the Laves phases are Curie-Weiss paramagnets, which demonstrate metallic conduction; 7x and 12x alloys also reveal a pronounced Kondo-like anomaly. Analysis of experimental data as well as ab initio calculations suggests that chemical complexity and compositional disorder cause strong s-d band scattering and thus the rather high density of d-states in the conduction band. Analysis of the results suggests that the mechanism of Laves phase formation in multicomponent multi-principal element metallic alloys is may be the same as in polydisperse hardspheres mixtures. Another important conclusion is that the configurational entropy is a negligible factor in the stabilization of multi-element Laves phases.

Recently, the demand for electric vehicle is increasing worldwide due to eco-friendly policies and stricter emission regulations. As a traction motor for electric vehicle, interior permanent magnet synchronous motors are mainly used. For the design of the interior permanent magnet synchronous motor, the magnetic equivalent circuit method, which is a method of lumped constant circuit, and the finite element method, which is a method of distributed constant circuit, mainly are used. Magnetic equivalent circuit method is useful for simple design through fast and intuitive parameters, but it cannot derive the distribution of magnetic field. The finite element method can derive an accurate magnetic field distribution, but it takes a long time to analyze and it is difficult to analyze intuitive design parameters. In this paper, magnetic equivalent circuit method and Carter coefficient are mixed for rotor structure design. This design method will be called the hybrid magnetic equivalent circuit method. Intuitive design parameters are derived through this hybrid magnetic equivalent circuit method. We will derive the Air gap flux density distribution according to rotor shape, no-load induced voltage, and cogging torque, and compare and verify it with the finite element method.

Enhancing the degree of functional multiplexing while assuring operational reliability and manufacturability at competitive costs are crucial ingredients for enabling comprehensive sample-to-answer automation, e.g., for use in common, decentralized “Point-of-Care” or “Point-of-Use” scenarios. This paper demonstrates a model-based ‘digital twin’ approach which efficiently supports the algorithmic design optimization of exemplary centrifugo-pneumatic (CP) dissolvable-film (DF) siphon valves towards larger-scale integration (LSI) of well-established “Lab-on-a-Disc” (LoaD) systems. Obviously, the spatial footprint of the valves and their upstream laboratory unit operations (LUOs) have to fit, at a given radial position prescribed by its occurrence in the assay protocol, into the locally accessible disc space. At the same time, the retention rate of a rotationally actuated CP-DF siphon valve and, most challenging, its band width related to unavoidable tolerances of experimental input parameters, need to slot into a defined interval of the practically allowed frequency envelope. To accomplish particular design goals, a set of parametrized metrics is defined, which are to be met within their practical boundaries while (numerically) minimizing the band width in the frequency domain. While each LSI scenario needs to be addressed individually on the basis of the digital twin, a suite of qualitative design rules and instructive showcases structures are presented.

Traditional discrimination techniques for Euler deconvolution use only the color spectrums of structural indexes, without considering the spatial distribution characteristics and inherent relationships among the Euler solutions to separate adjacent causative sources. In the present study, a new approach was developed for discriminating uncorrelated Euler solutions from coherent solutions based on the focusing levels indicated by the probability density distributions generated using multivariate kernel density estimations (KDE). A novel multiple coverage technique was proposed by using a series of different sized moving windows over gridded gravity data, which formed tight clusters of Euler solutions for different sized causative sources. The results of the probability density distributions were obtained using a 3-D KDE method for the Euler solution subsets {x, y, z} of synthetical models, and real data from a survey conducted in British Columbia (Canada) which had successfully established more credible and meaningful geological models when compared with three other subsets.

As in any other plant, in the grapevine roots play a vital role in terms of anchorage, uptake of water and nutrients, as well as storage and production of chemicals. Their behaviour and development depend on various factors, namely rootstock genetics, soil physical and chemical features, field agronomic practices. Canopy management, involving techniques such as defoliation and pruning, could greatly influence root growth. To date, most of the studies on grapevine winter pruning have focused on the effects on yield and quality of grapes, achievable by using different pruning systems and techniques, while the knowledge of root distribution, development, and growth in relation to winter pruning is still not well understood. In this contest, the purpose of this study was to investigate the effect of winter pruning on the root system of field-grown Vitis vinifera cv. Pinot Gris grafted onto rootstock SO4. We compared two pruning treatments (pruning-P and no pruning-NP) and analysed the effect on root distribution and density, root index and on the root sugar reserves. Root data were analysed in relation to canopy growth and yield, to elucidate the effect of winter pruning on the root/yield ratio. Our data indicated that winter pruning stimulated the root growth and distribution without compromising canopy development, while no-pruning treatment produced less growth of roots but a larger canopy. Information regarding root growth and root canopy ratio is important as it gives us an understanding of the relationship between the aerial and subterranean parts of the plant, how they compete, and finally, offers us the possibility to ponder on cultural practices.

For traffic management under sudden disaster in high-density areas, the first and foremost step is to prevent traffic congestion in the disaster-affected area by traffic flow control, as to provide enough and flexible traffic capacity for emergency evacuation and emergency rescue. Catastrophe border identification is the foundation and the key to traffic congestion prediction under sudden disaster. This paper uses a mathematical model to study the regional traffic flow in the high-density area under sudden fire disaster based on the Cusp Catastrophe Theory (CCT). The catastrophe border is identified by fitting the CCT-based regional traffic flow model to explore the stable traffic flow changing to the instable state, as to provide a theoretical basis for traffic flow manage and control in disaster-affected areas, and to prevent the traffic flow being caught into disorder and congestion. Based on VISSIM simulator data by building simulation scenarios with and without sudden fire disaster in a Sudoku traffic network, the catastrophe border is identified as 439pcu/lane/h, 529pcu/lane/h, 377pcu/lane/h at 5s, 10s, 15s data collection interval respectively. The corresponding relative precision, which compares to the method of Capacity Assessment Approach (CAA), is 89.1%, 92.7% and 76.5% respectively. It means that 10s data collection interval would be the suitable data collection interval in catastrophe border identification and regional traffic flow control in high-density area under sudden fire disaster.

The work is devoted to the investigation of virus quasispecies evolution and diversification due to mutations, competition for host cells, and cross-reactive immune responses. The model consists of a nonlocal reaction-diffusion equation for the virus density depending on the genotype considered as a continuous variable and on time. This equation contains two integral terms corresponding to the nonlocal effects of virus interaction with host cells and with immune cells. In the model, a virus strain is represented by a localized solution concentrated around some given genotype. Emergence of new strains corresponds to a periodic wave propagating in the space of genotypes. The conditions of appearance of such waves and their dynamics are described.

In thermal friction drilling (TFD) operations, the geometrical dimensions of bushing shape, height and wall thickness are the most vital consequences, due to increasing the connecting length and strength. In this paper, AA7075-T651 aluminum alloys with 2, 4, 6, 8, and 10 mm in thicknesses were drilled with TFD process in order to investigate the density, the volume ratio, and height and wall thickness of the bushings. The experiments were conducted at constant spindle speed and feed rate conditions by using HSS conical tools of 5, 10, 15, and 20 mm in diameters. It was experimentally found that the bushing height and the wall thickness were tendency of increase linearly with increasing both material thickness and tool diameter. The effect of tool diameter was found to have much of influence on the measured values than the thickness of the drilled material. The density of the bushing was changed inconsiderably. Approximately 70-75 % percentages of the evacuated material composed the bushing shape, in TFD operations.

Satellite-based remote sensing technologies are utilized extensively to investigate urban thermal environments under rapid urban expansion. Current MODIS data is, however, unable to adequately represent the spatially detailed information because of its relatively coarser spatial resolution, while Landsat data can’t explore temporally the refined analysis due to the low temporal resolution. In order to resolve this situation, we used MODIS and Landsat data to generate “Landsat-like” data by using the flexible spatiotemporal data fusion method (FSDAF), and then studied spatiotemporal variation of land surface temperature (LST) and its driving factors. The results showed that 1) The estimated “Landsat-like” data have high precision; 2) By comparing 2013 and 2016 datasets, LST increases ranging from 1.8°C to 4°C were measurable in areas where the impervious surface area (ISA) increased, while LST decreases ranging from -3.52°C to -0.70°C were detected in areas where ISA decreased; 3) LST has a strongly negative relationship with the Normalized Difference Vegetation Index (NDVI), and a strongly positive relationship with Normalized Difference Built Index (NDBI) in summer; and 4) LST is well correlated with Building density (BD), in a complex conic mode, and LST may increase by 0.460°C to 0.786°C when BD increases by 0.1. Our findings can provide information useful for mitigating undesirable thermal conditions and for long-term urban thermal environmental management.

Prebiotic organic synthesis reactions catalyzed by Earth-abundant metal sulfides are key processes for understanding the evolution of biochemistry from inorganic molecules, yet the catalytic functions of sulfides have remained poorly explored in the context of the origins of life. Past studies on prebiotic chemistry have mostly focused on a few types of metal sulfide catalysts, such as FeS or NiS, which form limited types of products with inferior activity and selectivity. To explore the potential of metal sulfides on catalyzing prebiotic chemical reactions, here, the chemical diversity (variations in chemical composition and phase structure) of 304 natural metal sulfide minerals in a mineralogy database was surveyed and approaches to rationally predict the catalytic functions of metal sulfides are discussed based on advanced theories and analytical tools of electrocatalysis such as proton-coupled electron transfer, structural comparisons between enzymes and minerals, and in-situ spectroscopy. To this end, we introduce a model of geo-electrochemistry driven prebiotic synthesis for chemical evolution, as it helps us to predict kinetics and selectivity of targeted prebiotic chemistry under “chemically messy conditions”. We expect that combining the data-mining of mineral databases with experimental methods and theories developed in the field of electrocatalysis will facilitate the prediction and verification of catalytic performance under a wide range of pH and Eh conditions, and aid in the rational screening of mineral catalysts involved in the origins of life.

The properties of the charged dark matters are discussed in terms of the new three-dimensional quantized space model. Because of the graviton evaporations, the very small Coulomb’s constant (k(dd)) of 10 ⁻⁴⁸ k and large gravitation constant (G_N(dd)) of 10⁶ G_N for the charged dark matters at the present time are expected. The tentative values of G and k are used for the explanation purpose. Therefore, F_c(mm) > F_g(dd) > F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = F_c(lq) = 0 for the proton-like particle. Also, the gravitation constant has been changed with increasing of the time because of the graviton evaporation. In the present work, the B1, B2 and B3 bastons with the condition of k(mm) = k >> k(dd) > k(dm) = 0 are explained as the good candidates of the dark matters. Also, the particle creation, dark matters and dark energy could be deeply associated with the changing gravitation constants (G). It is expected that the changing process of the gravitation constant between the matters from G_N(mm) ≈ 10³⁶ G_N to G_N(mm) = G_N happened mostly near the inflation period. Therefore, during most of the universe evolution the gravitation constant could be taken as G_N(mm) = G_N. And the effective charges and effective rest masses of the particles are defined in terms of the fixed Coulomb’s constant (k) and fixed gravitation constant (G_N). Then, the effective charge of the B1 dark matter with EC = −2/3 e is (EC)_eff = −2/3·10⁻²⁴ e. It is concluded that the photons, gravitons and dark matters are the first particles created since the big bang. The particles can be created from the decay of the matter universe and the pair production of the particle and anti-particle with decreasing of the gravitation constant (G_N(mm)). Also, the weak force, strong force and dark matter force bosons are created from the interactions of the elementary particles with the T fluctuations of the vacuum energy.

A novel plasma source of pulsed electrolyte cathode atmospheric pressure discharge (pulsed-ECAD) driven by an alternating current (AC) power supply coupled with a high voltage diode was generated, and the discharge was generated in the open-to-air atmosphere between a metal electrode and a small-sized flowing liquid cathode. The spatial distribution of plasma temperatures (excitation, vibrational and rotational) of the pulsed-ECAD were investigated. The electron excitation temperature of H T_exc(H), vibrational temperature of N₂ T_vib(N₂), and rotational temperature of OH T_rot(OH) were measured as 4900±36-6800±108 K, 4600±86-5800±100 K and 1050±20-1140±10 K, respectively. Meanwhile, the temperature characteristics of dc solution cathode glow discharge (dc-SCGD) were also studied for comparison with pulsed-ECAD. The effects of operating parameters, including discharge voltage and discharge frequency, on the plasma temperatures were investigated. The electron number density determined in the discharge system and dc-SCGD were within the range (3.8–18.9) ×10¹⁴ cm^-3 and 2.6×10¹⁴-17.2×10¹⁴ cm^-3, respectively.

The modern textbook analysis of the thermal state of photons inside a three-dimensional reflective cavity is based on the three quantum numbers that characterize photon’s energy eigenvalues coming out when the boundary conditions are imposed. The crucial passage from the quantum numbers to the continuous frequency is operated by introducing a three dimensional continuous version of the three discrete quantum numbers, that leads to the energy spectral density and to the entropy spectral density. This standard analysis obscures the role of the multiplicity of energy eigenvalues associated to the same eigenfrequency. In this paper we review the past derivations of Bose’s entropy spectral density and present a new analysis of energy spectral density and entropy spectral density based on the multiplicity of energy eigenvalues. Our analysis explicitly defines the eigenfrequency distribution of energy and entropy and uses it as a starting point for the passage from the discrete eigenfrequencies to the continuous frequency.

The catastrophic failure of two dams in Libya in the night of 10th and 11th September 2023, resulted in a significant amount of water and debris destroying a large part of the city of Derna, which is located downstream of the two dams. The flood caused more than 6000 fatalities and the dis-placement of thousands of people from the city. The dams failed due to heavy rainfall caused by the Medicane Daniel, resulting in intense precipitation and the dams overspilling after reaching full capacity. This paper analyses the consequences of the dam breach by modelling the flow discharge and the flooding of the city of Derna. The analysis compares the computed quantities with the findings of the post-event satellite image analysis from UNOSAT and Copernicus, the field reports, and information gathered from the social media through AI detection. The results allows to better understand the dynamics of the dam breach, its initial parameters and an assessment of the accu-racy of the results.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

Estrogens play a protective role during early life stages. However, endogenous 17β-estradiol (E2) can accelerate atherosclerosis progression in low-grade inflammatory conditions like established atherosclerosis. Our single-center cohort study assessed sex-specific associations of gonadal hormones with oxidative stress, inflammation, and myocardial injury markers in 111 patients (37% women) diagnosed with acute myocardial infarction (MI) between July 2011 and December 2013. Blood samples were collected within 48 hours of symptom onset, and we measured sex steroids (E2, total testosterone [T]), oxidized low-density lipoproteins, high-sensitive C-reactive protein (CRP), white blood cell counts (WBC), and cardiac enzymes (creatine kinase [CK], the CK Muscle-Brain fraction [CK-MB], and high-sensitive troponin T [hsTnT]). The SYNTAX score gauged coronary disease severity from coronary angiography results. In men with acute MI, peak cardiac enzyme levels were predicted by post-percutaneous coronary intervention (PCI) E2 plasma levels (OR 1.011, p=0.047 - CK; OR 1.018, p=0.013 - CK- MB; OR 1.019, p=0.005 - TnT), peak WBC count (OR 1.487, p=0.015 - CK ; OR 1,709, p=0,005 - CK- MB; OR 1.391, p=0.012 - TnT), and peak CRP plasma levels (OR 1.040, p=0.033 - CK; OR 1.024, p=0.029 - CK-MB; OR 1.063, p=0.006 - TnT). T levels and E2/T ratio were associated with post-PCI CRP in these men (OR 0.980, p = 0.024 - T, OR 1.010, p = 0.076 - CRP). For women, peak WBC was a marker of highest testosterone (OR 1.348, p = 0.062), and only WBC was a significant indicator of myocardial injury extent (OR 1.426, p=0.039 - CK; OR 1.384, p=0.036 - CK-MB; OR 1.299, p=0.048 - TnT). During acute MI, elevated endogenous estradiol levels correlate with myocardial necrosis severity in men, while in women, increased leukocyte levels indicate acute myocardial damage. Elevated plasma T is associated with increased WBC in women. In men, post-PCI plasma CRP specifically indicates endogenous T levels and E2/T ratio during the acute phase.

Optimum design and accurate control of the internal structure of the laser target materials remain an important goal for various laser physics experiments, especially for generating high flux photon and neutron beams. The low-density material is considered to be one of the most difficult for X-ray study due to its high transparency and imperceptible contrast. To produce clear visualization of foam containing sparse structures we used a high-quality monochromatic X-ray beam of synchrotron radiation source PETRA-III at DESY. The X-ray beam parameters allow tomographic scanning with application of phase contrast retrieval algorithms. A series of 3D images of foam-suspended glass microsphere inside the plastic cylinder were obtained with the quality high enough to observe the internal structure and to visualize uniformity, displacement and surface roughness on both sides of the microsphere. The main object under investigation was a CH-plastic capillary including 10 mg/cc CHO-foam with the centered glass microsphere. The results of this work demonstrate that tomographic visualization based on a high quality X-ray radiation and phase contrast analysis is an effective and useful technique for development of new laser targets containing structured low density materials.

In the present study, we studied the effect of apolipoprotein A-1 (APOA1) on the spatial and molecular characteristics of bone marrow adipocytes, using well-characterized ApoA1 knockout mice. APOA1 is a central regulator of high-density lipoprotein cholesterol (HDL-C) metabolism, and thus HDL; our recent work showed that deficiency of APOA1 increases bone marrow adiposity in mice. We found that ApoA1 deficient mice have greatly elevated adipocytes within their bone marrow compared to wild type counterparts. Morphologically, the increased adipocytes were similar to white adipocytes, and displayed proximal tibial-end localization. Marrow adipocytes from wild type mice were significantly fewer and did not display bone-end distribution pattern. The mRNA levels of the brown/beige adipocyte-specific markers Ucp1, Dio2, Pat2, Pgc1a, and the expression of leptin were greatly reduced in the ApoA1 knock-out in comparison to the wild-type mice. In the knock-out mice adiponectin was remarkably elevated. In keeping with the close ties of hematopoietic stem cells and marrow adipocytes, we found that the elevated adiposity in the ApoA1 knock out mice is associated with a significant reduction of the hematopoietic stem cells and common myeloid, but not common lymphoid, progenitors. Moreover, the “beiging”-related marker osteopontin and the angiogenic factor VEGF were also reduced in the ApoA1 knock-out mice, further supporting the notion that APOA1, and most probably HDL-C, regulate bone marrow microenvironment, favouring beige/brown adipocyte characteristics.

The aim of this paper was to evaluate the changes in the mean bone density values of the midpalatal suture in 392 young patients treated with the Rapid Palatal Expander appliance according to sex, gender, vertical and sagittal skeletal patterns. Materials and Methods. The evaluations were performed using the low-dose protocol cone-beam computed tomography scans at t0 (preoperatively) and t1 (1 year after the beginning of the therapy). The region of interest was used to calculate bone density in Hounsfield units (HU) in the area between the maxillary incisors. Results. CBCT scan data of 196 females and 196 males (mean age of 11,7 years) showed homogeneous and similar density values of the MPS at T0 (547.59 HU - 565.85 HU) and T1 (542.31 - 554.20 HU). Class III skeletal individuals showed a significant higher BD than the II class group at T0, but not at T1. Females showed significantly higher BD than males at t0 and t1. No significant differences were found between the other groups and between two-time points in terms of bone density values of the MPS. Conclusions. Females and III class groups showed significantly higher bone density values than males and II class, respectively. No statistically significant differences were found from T0 to T1 in any groups, suggesting that a similar rate of suture reorganization occurs after the use of the RPE, following reorganization and bone deposition along with the MPS.

Phenol is added to acetophenone (methyl phenyl ketone) and to six of its halogenated derivatives in a supersonic jet expansion to determine the hydrogen bonding preference of the cold and isolated 1:1 complexes by linear infrared spectroscopy. Halogenation is found to have a pronounced effect on the docking site in this intermolecular ketone balance experiment. The spectra unambiguously decide between competing variants of phenyl group stacking due to their differences in hydrogen bond strength. Structures where the phenyl group interaction strongly distorts the hydrogen bond are more difficult to quantify in the experiment. For unsubstituted acetophenone, phenol clearly prefers the methyl side despite a predicted sub-kJ/mol advantage which is nearly independent of zero point vibrational energy, turning this complex into a challenging benchmark system for electronic structure methods which include long range dispersion interactions in some way.

The 32CA reactions of a series of pairs of bent three-atom-components (B-TACs) and linear TACs (L-TACs) towards electrophilic dicyanoethylene (DCE) have been studied within the Molecular Electron Density Theory in order to understand their different reactivity. ELF analysis indicates that while pseudodiradical B-TACs change their electronic structure to pseudoradical or carbenoid L-TACs upon dehydrogenation, zwitterionic B-TACs experience no remarkable change. Analysis of the CDFT indices indicates that five of the nine studied TACs have a strong nucleophilic character, thus participating in polar reactions towards electrophilic ethylenes. The activation energies of the 32CA reactions of the nine TACs towards electrophilic DCE range from 0.6 to 22.0 kcal·mol-1, which are by between 2.0 and 10.1 kcal·mol-1 lower than those involved in the non-polar 32CA reactions with ethylene. In general, B-TACs are more reactive than their L-TAC counterparts. A change of the regioselectivity is found in these polar 32CA reactions; in general, while B-TACs are meta regioselective, L-TACs are ortho regioselective. Analysis of the geometrical parameters indicates that at all TSs, the formation of the single bond involving the most electrophilic C4 carbon of DCE is more advanced than that involving the C5 one. A change of the asynchronicity in the reactions involving B-TACs and L-TACs is also found.

This paper presents sufficient conditions for almost global stability of nonlinear switched systems consisting of both stable and unstable subsystems. Techniques from the stability analysis of switched systems have been combined with the multiple Lyapunov density approach - recently proposed by the authors for the almost global stability of nonlinear switched systems composed of stable subsystems. By using slow switching for stable subsystems and fast switching for unstable subsystems lower and upper bounds for mode-dependent average dwell times are obtained. In addition to that, by allowing each subsystem to perform slow switching and using some restrictions on total operation time of unstable subsystems and stable subsystems, we have obtained a lower bound for an average dwell time.

The design of more efficient photosensitizers is a matter of great importance in the field of cancer treatment by means of photodynamic therapy. One of the main processes involved in the activation of apoptosis in cancer cells is the oxidative stress on DNA once a photosensitizer is excited by light. As a consequence, it is a matter of great relevance to investigate in detail the binding modes of the chromophore with DNA, and the nature of the electronically excited states that participate in the induction of DNA damage, for example, charge-transfer states. In this work, we investigate the electronic structure of the anthraquinone photosensitizer intercalated into a double-stranded poly(dG-dC) decamer model of DNA. First, the different geometric configurations are analyzed by means of classical molecular dynamics simulations. Then, the excited states for the most relevant poses of anthraquinone inside the binding pocket are computed by an electrostatic-embedding quantum mechanics/molecular mechanics approach, where anthraquinone and one of the nearby guanine residues are described quantum mechanically to take into account intermolecular charge-transfer states. The excited states are characterized as monomer, exciton, excimer and charge-transfer states based on the analysis of the transition density matrix, and each of these contributions to the total density of states and absorption spectrum is discussed in terms of the stacking interactions. These results are relevant as they represent the footing for future studies on the reactivity of anthraquinone derivatives with DNA and give insights on possible geometrical configurations that potentially favor the oxidative stress of DNA.

Southern highbush blueberry plantations have been expanded into worldwide non-traditional growing areas with elite cultivars and improved horticultural practices. This article presents a comprehensive review of current production systems – alternatives to traditional open field production – such as production in protected environments, high-density plantings, evergreen production, and container-based production. We discuss the advantages and disadvantages of each system and compare their differences to the open field production. In addition, potential solutions have been provided for some of the disadvantages. We also highlight some of the gaps existing between academic studies and production in industry, providing a guide for future academic research. All these alternative systems have shown the potential to produce high yields with high quality berries. Alternative systems, compared to the field production, require higher establishment investments and thus create an entry barrier for new producers. Nevertheless, with their advantages, alternative productions have potential to be profitable.

With reference to Planck scale, increasing support for large scale cosmic anisotropy and preferred directions and by considering an increasing ratio of Hubble parameter to angular velocity, right from the beginning of Planck scale, we make an attempt to estimate ordinary matter density ratio, dark matter density ratio, mass, radius, temperature, age and expansion velocity (from and about the baby universe in all directions). We would like suggest that, from the beginning of Planck scale, 1) Dark matter can be considered as a kind of cosmic foam responsible for formation of galaxies. 2) Cosmic angular velocity decreases with square of the decreasing cosmic temperature. 3) Increasing ratio of Hubble parameter to angular velocity plays a crucial role in estimating increasing cosmic expansion velocity and decreasing density ratios of dark matter and ordinary matter. 4) There is no need to consider dark energy for understanding cosmic acceleration.

The regulation of hepatic very-low-density lipoprotein (VLDL) secretion plays an important role in the pathogenesis of dyslipidemia and fatty liver diseases. VLDL is controlled by hepatic microsomal triglyceride transfer protein (MTTP). Mttp is regulated by carbohydrate response element binding protein (ChREBP) and small heterodimer partner (SHP). However, it is unclear whether both coordinately regulate Mttp expression and VLDL secretion. Here, adenoviral overexpression of ChREBP and SHP in rat primary hepatocytes induced and suppressed Mttp mRNA, respectively. However, Mttp induction by ChREBP was much more potent than suppression by SHP. Promoter assays of Mttp and the liver type pyruvate kinase gene revealed that SHP and ChREBP did not affect the transactivity of each other. Mttp mRNA and protein levels of Shp^/– mice were similar to those of wild-type; however, those of Chrebp^–/–Shp^–/– and Chrebp^–/– mice were much lower. Consistent with this, the VLDL particle number and VLDL secretion rates in Shp^–/–- mice were similar to wild-type, but were much lower in Chrebp^–/– and Chrebp^–/–Shp^–/–- mice. These findings suggested that ChREBP rather than SHP regulates VLDL secretion and that ChREBP and SHP do not affect the transactivities of each other.

Cropland area per capita and pressure index on cropland is the important parameters measuring the social vulnerability and sustainability in the perspective of food security in a certain region in China during the historical periods. This study reconstructs the spatial distribution change of cropland area per labor/household and pressure index on cropland during the 17th-20th century by the methods of historical documents, regression analysis, pressure index model and GIS. Then it analyzed the impacting process of climate change and sustainability of cropland use during the different periods. It draws conclusions: (i) the spatial difference of labor/household density was obvious which had the same pattern as cropland distribution during the same periods, which is higher density in three agricultural areas. (ii) Cropland area per capita was relatively higher during the 17th-18th century, which were above 0.4 ha/person in majority counties and distributed homogenously. Till the 19th century and the beginning of 20th century, cropland area per capita in large amount of regions decreased below 0.2 ha/person embodying the increase of social vulnerability and unsustainability at that time. (iii) Pressure index on cropland also showed the similar spatial pattern as cropland area per capita which presented lower threshold than nowadays. During the 17th-18th century there was no pressure on cropland. While, in the 19th century and at the beginning of 20th century, two high value centers of pressure index on cropland appeared in Middle Shandong and the Jiaodong region, pressure on sustainable cropland use increased obviously and a food crisis is probably created. (iv) Higher sustainable extent of cropland use corresponds to cold period, and lower sustainable extent of cropland use corresponds to warm period in Shandong over the past 300 years. The turning point of 1680s from dry to wet attributes to the decrease of sustainable extent of cropland use in Shandong not very distinctively. More and more pressure on sustainability of cropland use finally since the beginning of 20th century would intensify the social conflict and increase the probability of social revolts.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

Information geometry (IG) is a fascinating combination of differential geometry and statistics where a Riemannian manifold's structure is applied to a statistical model. It may find numerous fascinating uses in the domains of theoretical neurology, machine learning, complexity, and (quantum) information theory, among others. (IG) aims to provide a differential-geometric perspective on statistical geodesic models' structure. In this case, IG, KD, and J-divergence (JD) are used to define the manifold of the Generalised Brownian Motion (GBM). Consequently, the geodesic equations (GEs) are devised, and GB information matrix exponential (IME) is presented. Moreover, for first time ever, the necessary and sufficient mathematical requirement that characterizes the developability of Generalized Brownian Motion(GBM) manifold is devised. Also, a novel sufficient and necessary conditions which characterizes the regions where the surface describing GBM is minimal is determined. Also, it is shown that GBM has a non-zero 0-Gaussian and Ricci curvatures. Consequently, this advances the establishment of a unified GBM- Relativistic Info-Geometric based analysis.

Hydroxyapatite (HAP) is the main mineral component of bones and teeth. It is widely used in medicine as a bone filler and coating for implants to promote new bone growth. Ion substitutions into the HAP structure highly affect its properties. One of the important substituents is manganese. This paper presents the new results obtained by high-precision density functional theory calculations using hybrid functionals, for studies of the Mn/Ca substitutions in HAP in a wide manganese concentration range within 2x2x2 supercell model. The experimental data on the mechanochemical synthesis of HAP-Mn samples with different Mn concentrations are also presented. The comparison between experiment and theory showed good agreement: the HAP-Mg unit cell parameters and volume decrease with increasing degree of Mn/Ca substitution. It is shown that electronic energy levels appear inside the band gap Eg of HAP, which depend on the concentration of Mn and change the photo-excitation energy of HAP, making its effective value Eg* less than the band gap Eg, and generally changing the photoelectronic properties of HAP. It was established that the energies of formation of the substitutions Mn/Ca depend on the position of the Ca atom (Ca1 or Ca2) and on the concentration of manganese. It has been shown that the replacement of calcium cations with manganese occurs predominantly at the Ca2 position.

We report on ground-based measurements of the atmospheric electric field (Ez= -Potential Gradient (PG)) and current density (Jz) that were conducted at two locations in Israel. One is the Emilio Segre cosmic ray station located on Mt. Hermon (34.45 N, 2020 m AMSL) located in northern Israel near the Syrian-Lebanon border and at the other at the Wise astronomical observatory in the Negev desert highland plateau of southern Israel (31.18 N, 870 m AMSL). We searched for possible effects of strong, short-term solar events on the potential gradient and the vertical current density, as disruption to the Global Electric Circuit are often observed following strong solar events. The first case study (St. Patrick Day, 17 March 2015) was classified as the strongest event of 2015. The second case study (8 Sep 2017) was categorized as the strongest event of 2017 and one of the twenty strongest events on record to date. The results show that the electrical parameters measured at ground level at both stations were not affected during the two massive proton events and the ensuing geomagnetic storms. The magnetospheric shielding in lower latitudes is strong enough to shield against flux of energetic particles from solar events, obscuring any impact that may be noticeable above the local daily variations induced by local meteorological conditions (aerosol concentrations, clouds, high humidity, and wind speed) which were investigated as well.

In the present work, we report on a 3D MOF of {[Pb5(3-OH)(3-NO3)3(6-pmdc)3·H2O}n formula (pmdc = pyrimidine-4,6-dicarboxylate) synthesized by an oven-heated solvent-free procedure. The large connectivity afforded by the three ligands in their coordination to lead(II) ions grows cubic building units characterized by a central Pb atom with an unusual coordination index of 12 and six pmdc ligands occupying the faces. These cubic units are linked one another giving rise to a quite condensed structure that represents an unprecedented topology showing the (4.62)6(43)2(45.610)3(45.68.82)6(46.69)6(612.83) point symbol. The crystalline material has been characterized by routine physico-chemical techniques to confirm its purity and its thermal behaviour has been also studied by thermogravimetric and thermodiffractometric analyses. The solid presents greenish blue photoluminescent emission based on pmdc ligands, as revealed time-dependent density-functional theory (TD-DFT) calculations, by that is substantially more intense than in free H2pmdc ligand according to its improved quantum yield. The emissive capacity of the material is further analysed according to decreasing temperature of the polycrystalline sample, finding that sizeable long-lasting phosphorescence is present.

Growing population, industrialization, and power requirements are adversely affecting the environment by increased greenhouse gases, resulting from fossil fuel burning. Global greenhouse gas mitigation targets have led the nations to promote clean and self-renewable sources of energy to address the environmental issue. Offshore wind power resources are relatively more attractive due to high winds, less turbulence, minimal visualization effects, and no interaction of infrastructure. The present study aims at conducting offshore wind power resources assessment (OWPRA) at some locations in the Gulf of North Suez. For this purpose, the long-term hourly mean wind speed (WS) and wind direction above means sea level (AMSL) and temperature and pressure data near surface is used. The data is obtained from ERA5 (fifth generation reanalysis for the global climate weather) at chosen six (L1-L6) offshore locations. The data covers a period of 43 years, between 1979 and 2021. The WS and direction are provided at 100 m AMSL while temperature and pressure are available near water surface level. At L1 to L6 locations, the log-term mean WS and wind power density (WPD) values are found to be 7.55 m/s and 370 W/m2, 6.37 m/s and 225 W/m2, 6.91 m/s and 281 W/m2, 5.48 m/s and 142 W/m2, 4.30 m/s and 77 W/m2, and 5.03 and 115 W/m2 and at 100 m AMSL; respectively. The higher magnitudes of monthly and annual windy site identifier indices (MWSI and AWSI) of 18.68 and 57.41 and 12.70 and 42.94 at L1 and L3 sites and generally lower values of wind variability indices are indicative of favourable winds source, which is also supported by higher magnitudes of mean WS, WPD, annual energy yields, plant capacity factors, and wind duration at these sites. The cost of energy, for the worst and the best cases are estimated as 10.120 USD/kWh and 1.274 USD/kWh at L5 and L1 sites corresponding to wind turbines WT1 and WT4. Based on the analysis, sites L1, L3, and L2 are recommended for wind farm development in order of preference. The wind variability and windy site identifiers indices introduced, will help decision-makers in deciding the potential windy sites with more confidence.

In this paper, we investigate the structural, microstructural, dielectric, and energy storage properties of Nd and Mn co-doped Ba0.7Sr0.3TiO3 [(Ba0.7Sr0.3)1-xNdxTi1-yMnyO3 (BSNTM) ceramics (x = 0, 0.005, and y = 0, 0.0025, 0.005, and 0.01)] via a defect dipole engineering method. The complex defect dipoles (MnTi"-VO∙∙)∙ and (MnTi"-VO∙∙) between acceptor ions and oxygen vacancies capture electrons, enhancing the breakdown electric field and energy storage performances. XRD, Raman spectroscopy, and microscopic investigations of BSNTM ceramics revealed the formation of a tetragonal phase, increased oxygen vacancies, and reduced grain size with Mn dopant, respectively. The BSNTM ceramics with x=0.005 and y=0 exhibit a high dielectric constant of 2058 and a dielectric loss of 0.026 at 1 kHz. These values gradually decreased to 1876 and 0.019 for x=0.005 and y=0.01 due to the Mn2+ ions at Ti4+-site, which facilitates the formation of oxygen vacancies, and prevents the decrease of Ti4+. In addition, the defect dipoles act as a driving force for depolarization to tailor the domain formation energy and domain wall energy, which provides a high difference between the maximum polarization of Pmax and remnant polarization of Pr (ΔP=10.39 µC/cm2). Moreover, the complex defect dipoles with optimum oxygen vacancies in BSNTM ceramics can provide not only a high ΔP but also reduce grain size, which together improve the breakdown strength from 60.4 to 110.6 kV/cm, giving rise to a high energy storage density of 0.41 J/cm3 and high efficiency of 84.6% for x=0.005 and y=0.01. These findings demonstrate that defect dipoles engineering is an effective method to enhance the energy storage performance of dielectrics for capacitor applications.

Background: The mechanisms underlying the effect of estradiol (E2) on low-density lipoprotein cholesterol (LDL-C) levels are not completely understood, although a role for proprotein con-vertase subtilisin/kexin type 9 (PCSK9) has been proposed. We aimed to investigate the association between levels of E2, PCSK9 and lipid parameters in premenopausal women undergoing in vitro fertilization (IVF). Methods: Healthy women undergoing IVF in the Department of Obstetrics and Gynecology of the University General Hospital of Ioannina were recruited. Levels of E2, pro-protein convertase subtilisin/kexin type 9 (PCSK9), total cholesterol (TCHOL), high-density lip-oprotein cholesterol (HDL-C), LDL-C, and triglycerides (TGs) were measured 10 days after ovarian depression (E2min) and 7 days after ovarian stimulation (E2max). Results: A total of 34 consecutive healthy women aged 38 (26-46) years old who underwent a full IVF cycle were included. E2 levels increased by 329.6% from E2min to E2max (108 [47-346] to 464 [241-2471] pg/mL, p<0.05). At the same time, serum PCSK9 levels significantly decreased by 30.8% (245 ± 80 to 170 ± 64 ng/mL, p<0.05). No significant changes in TCHOL, LDL-C, TGs and HDL-C were found (-0.4%, -3.8%, -2.2%, and +5.3%, p >0.05). Conclusions: The increase in endogenous E2 production during an IVF cycle was associated with a significant decrease in serum PCSK9 levels during a 7-day period.

In the Formula Student Racing Car, the anti-deformation ability of the frame will affect the four-wheel positioning parameters of the racing car, and then affect the handling and stability performance of the racing car. The quality of the frame directly determines the power and economy of the racing car, so the performance of the frame is very important to the performance of the race. In order to improve the performance of the frame and reduce the total weight of the frame, the research on the lightweight design of the frame is particularly important. In this paper, based on the variable density method, the global topology optimization of the frame is carried out to obtain the distribution of the frame material, realize the efficient use of the material, and improve the torsional stiffness of the frame. Based on the adjoint variable method, the sensitivity analysis of the frame is carried out. According to the sensitivity analysis results, the size of the frame is optimized. The total mass of the frame is reduced by 12.8 %, and the performance of the maximum displacement and maximum stress is improved. The lightweight design of the frame is realized as a whole.

Nowadays, bioeconomy and nanotechnology trends push food packaging sector in the re-placement of food additives by biobased antioxidant/antibacterial compounds and their inclusion in nanocarriers to control their release. Herein by following this trend, a rich in thymol-(TO) activated carbon (AC) nanostructure (TO@AC) was prepared and physiochemically characterized with various technics. This TO@AC nanostructure as well as pure AC were extruded with low density polyethylene (LDPE) to develop novel active packaging LDPE/TO@AC and LDPE/AC films. X-ray diffractometry, Fourier Transform Infrared Spectroscopy and Scanning Electron Microscopy measuraments shown high dispersity and capability of both AC and TO@AC in LDPE matrix which was resulted in enhanced tensile and water/oxygen barrier properties of obtained LDPE/AC and LDPE/TO@AC films. LDPE/TO@AC films shown higher elongation at break values and water/oxygen barrier than LDPE/AC films and significant antioxidant activity. TO release kinetics studies shown that by increasing TO@AC content the total TO amount released increased and the constant release rate decreased. Pork fillets wrapped with the optimum active film containing 15 wt.% TO@AC and succeed to prevent lipid oxidation and heme iron loss during storage. Estimation of microbial population of pork fillets shown that this active film could ex-tend the microbiological shelf-life of pork fillets by 2 days

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

The influence of distant London dispersion forces on the docking preference of alcohols of different size between the two lone electron pairs of the carbonyl group in pinacolone is explored by infrared spectroscopy of the OH stretching fundamental in supersonic jet expansions of 1:1 solvate complexes. Experimentally, no pronounced tendency of the alcohol to switch from the methyl to the bulkier tert-butyl side with increasing size is found. In all cases, methyl docking dominates by at least a factor of two, whereas DFT-optimized structures suggest a very close balance for the larger alcohols, once corrected by CCSD(T) relative electronic energies. Together with inconsistencies when switching from a C4 to a C5 alcohol, this points at deficiencies of the investigated B3LYP and in particular TPSS functionals even after dispersion correction, which cannot be blamed on zero point energy effects. The search for density functionals which describe the harmonic frequency shift, the structural change and the energy difference between the docking isomers of larger alcohols to unsymmetric ketones in a satisfactory way is open.

We analyzed the peak spring tidal current speeds, annual mean tidal power densities (TPD) and annual energy production (AEP) obtained from experiment 06.1, referred as the "HYCOM model" throughout, of the three dimensional (3D), global model HYCOM in an area covering the Baja California Pacific and the Gulf of California. The HYCOM model is forced with astronomical tides and surface winds alone, and therefore is particularly suitable to assess the tidal current and wind-driven current contribution to in-stream energy resources. We find two areas within the Gulf of California, one in the Great Island Region and one in the Upper Gulf of California, where peak spring tidal flows reach speeds of 1.1 meters per second. Second to fifth-generation tidal stream devices would be suitable for deployment in these two areas, which are very similar in terms of tidal in-stream energy resources. However, they are also very different in terms of sediment type and range in water depth, posing different challenges for in-stream technologies. The highest mean TPD value when excluding TPDs equal or less than 50 W/m² (corresponding to the minimum velocity threshold for energy production) is of 172.8 W/m², and is found near the town of San Felipe, at (lat lon) = (31.006 -114.64); here energy would be produced during 39.00% of the time. Finally, wind-driven currents contribute very little to the mean TPD and the total AEP. Therefore, the device, the grid, and any energy storage plans need to take into account the periodic tidal current fluctuations, for optimal exploitation of the resources.

Synthetic chalcomenite-type cupric selenite CuSeO₃∙2H₂O has been studied at room temperature under compression up to pressures of 8 GPa by means of single-crystal X-ray diffraction, Raman spectroscopy, and density-functional theory. According to X-ray diffraction, the orthorhombic phase undergoes an isostructural phase transition at 4.0(5) GPa with the thermodynamic character being first-order. This conclusion is supported by Raman spectroscopy studies which have detected the phase transition at 4.5(2) GPa and by the first-principles computing simulations. The structure solution at different pressures has provided information on the change with pressure of unit-cell parameters as well as on the bond and polyhedral compressibility. A Birch-Murnaghan equation of state has been fitted to the unit-cell volume data. We found that chalcomenite is highly compressible with a bulk modulus of 42 – 49 GPa. The possible mechanism driving changes in the crystal structure is discussed, being the behavior of CuSeO₃∙2H₂O mainly dominated by the large compressibility of the coordination polyhedron of Cu. On top of that, an assignation of Raman modes is proposed based upon density-functional theory and the pressure dependence of Raman modes discussed. Finally, the pressure dependence of phonon frequencies is also reported.

The research objectives was to determine the plants vegetation profile in forest revegetation and Mount Arjuna springs. The method used was descriptive method. While based on the techniques and tools used to research, the author uses the survey method to obtain facts that occur in the research area, namely in the area around the springs of Arjuna mount, Pasuruan, East Java, Indonesia. Data obtained in the field are then processed and analyzed using GIS, ArcView 3.3 and Google Earth programs. The results of the study explain the profile of plant vegetation, namely plant stratification, bird wealth, taxonomic wealth and plant density have a significant effect on forest revegetation and springs in Arjuna mount. The forest vegetation profile has a positive and significant effect on the preservation of springs. The better the profile of forest vegetation, the preservation of springs will be better, and vice versa.

Carbonate precipitation induced by microorganism has become a hot spot in the field of carbonate sedimentology, while the effect of different magnesium on biominerals has rarely been studied. Therefore, magnesium sulfate and magnesium chloride were used to investigate the significant role played on carbonate minerals. In this study, Staphylococcus epidermidis Y2 was isolated and identified by 16S rDNA homology comparison. The ammonia, pH, carbonic anhydrase, carbonate and bicarbonate ions were investigated. The mineral phase, morphology and elemental composition were analyzed by XRD and SEM-EDS. The ultrathin slices of bacteria were analyzed by HRTEM-SAED and STEM. The result showed that this bacterium could release ammonia and carbonic anhydrase to increase pH, and elevate the supersaturation via a large number of carbonate and bicarbonate ions released through carbon dioxide hydration catalyzed by carbonic anhydrase. The crystal cell density of monohydrocalcite was lower in magnesium chloride medium than that in magnesium sulfate medium. The crystal grew in a mode of spiral staircas in magnesium sulfate medium, while in a concentric circular pattern in magnesium chloride medium. There was no obvious intracellular biomineralization. This study may be helpful to further understand the biomineralization mechanism, may also provide some references for the reconstruction of paleogeological environment.

Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

In recent years, online social networks have received important consideration in spatial modelling fields given the critical information that can be extracted from them for events in real time; one of the most latent issues is that regarding various natural disasters such as earthquakes. Although it is possible to retrieve data from these social networks with embedded geographic information provided by GPS, in many cases this is not possible. An alternative solution is to reconstruct specific locations using probabilistic language models, more specifically those based on Name Entity Recognition (NER), which extracts names from a user’s description about an event occurring in a specific place (e.g., a collapsed building on a specific avenue). In this work, we present a methodology to use twitter as a social sensor system for disasters. The methodology scores NER locations with a kernel density estimation function for different subtopics originating from a natural disaster and that maps them into a geographic space is proposed. The proposed methodology is evaluated with tweets related to the 2017 earthquake in Mexico.

The direct measurements of the magnetic flux density in steel blocks within Compact Muon Solenoid (CMS) magnet yoke are performed with 22 flux loops installed in selected regions of the yoke. The 10,000-ton CMS magnet flux return yoke encloses a 4 T superconducting solenoid with a 6-m-diameter by 12.5-m-length free bore and consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end. The yoke steel blocks, mostly up to 620 mm thick, serve as the absorber plates of the muon detection system. A TOSCA 3-D model of the CMS magnet has been developed to describe the magnetic field everywhere outside of the tracking volume which was measured with a field-mapping machine. In the present study, for the first time, the reliable reconstruction of the magnetic flux density in the steel blocks of the yoke is performed using the CMS magnet standard discharges from the operational magnet current of 18.164 kA. To provide this reconstruction, the voltages induced in the flux loops (with amplitudes of 20–250 mV) have been measured with six 16-bit DAQ modules and integrated offline over time. The results of the flux loop measurements during three magnet ramp downs are presented and discussed.

The total enthalpies of the 16 different spin configurations that can be realized in the unit cell of the archetype spin crossover complex [Fe(phen)₂(NCS)₂] (phen=1,2-phenanthroline) were calculated applying periodic density functional theory combined with the Hubbard model and the Grimme-D2 dispersion correction (DFT+U/D2). The obtained enthalpy differences between the individual spin configurations were used to determine spin couplings of an Ising-like model and subsequent Monte Carlo simulations for this model allowed to estimate the phenomenological interaction parameter Г of the Slichter-Drickamer model, which is commonly used to describe the cooperativity of the spin transition. The calculational procedure described here, which led to an estimate of about 3 kJ/mol⁻¹ for Г, in good agreement with experiment, may be used to predict from first principles how modifications of spin crossover complexes can change the character of the spin transition from gradual to abrupt and vice versa.

The Folla Redonda grape is indigenous to the region of Rias Bajas in Galicia, Spain. This grape is distinguished by its characteristic acid flavor and pulp of remarkable coloration. Despite the wine obtained from this grape is highly valued by consumers of this region for its surprising acidic notes and thickness, it is important to note that it is not a variety of Vitis vinifera and its production is not legally regulated. In the present study, an evaluation of the physicochemical properties of the Folla Redonda grape (pH, °Brix, °Bé, density, acidity, sugar content, etc.) as well as its content in bioactive compounds (total polyphenols and anthocyanins) was carried out. Additionally, the antioxidant potential of the extracts obtained from this grape was demonstrated. This study proved the interesting organoleptic characteristics of the grape, along with a high content of compounds of interest and an important antioxidant activity comparable to that of Vitis vinifera grapes. Therefore, the grape's natural consumption and its application in different industries such as nutraceutical or pharmacological would result in an important revaluation of the grape and significant health benefits. In case that the production of wine from this variety is legalized, consumers will not only be able to enjoy a wine with a characteristic dense reddish color and important acid tones, but also with interesting concentrations of bioactive compounds.

Within the context of sustainable material development for the construction sector, this study explores the viability of panels composed of recycled newspaper-derived cellulose (9%), rice husk (14%), borax (15%), and polyvinyl acetate-based glue (62%). The methods employed involve water absorption and density tests, following ASTM C-1763 and C-303 standards. The fire resistance test conforming to the European standard UNE 23-725-90, and a mold growth test using AOAC 2002.11. The composite is prone to absorbing a significant amount of water when exposed to humid conditions. However, the incorporation of rice husk and borax can provide benefits such as improved moisture resistance compared to other cellulitic insulators, which may be advantageous in specific climates. Also, the developed composite has an intermediate density compared to other polymeric materials. This characteristic presents advantages in applications that demand a balance between strength and lightness. During the fire resistance tests, the samples with borax presented less fire propagation, and superficial damage compared with the specimens without borax. This is important, considering the fireproofing property, required in building materials. The presence of borax in the composite has an inhibitory effect on the growth of fungi and yeasts. These findings are consistent with previous research. Nevertheless, further research and testing are imperative to assess its viability and performance for commercial applications.

Brushless Direct Current Motors are significantly improved for using many electrical applications. The design investigation is increased year by year and most of the motor design researchers find out the superior efficiency of the BLDC motor. The traditional motor consumed more electrical power than BLDC motor. The design of BLDC motors that are compact, small, easy to control, save energy and light weight. Due to this fact, the design of BLDC motor should be analyzed to improve the motor characteristics performance. The research focuses on the design of BLDC motor performance using Taguchi Method and Response Surface Methodology (RSM) for Finite Element Method (FEM). Firstly, the Taguchi Method is applied to identify the optimization point of design parameters and consider using the reference model of actual BLDC electric fan motor with a rated power of 26Watts design. Based on the Taguchi Method to create the RSM is used to two-step optimization design performance using in FEM analysis. The performances of motor design proposed approach to provide the effeteness for motor design investigator. In this investigation aims the better structural performances in output power, torque, efficiency and torque ripple. The final design of proposed model achieved an energy efficiency is 10% higher than the reference design of prototype modes, the output power result is 10W higher this reference design. We can reduce the loss of the proposed motor design. Furthermore, the maximum torque can also increase the 0.032Nm of that design. The design simulation results were produced and studied by the FEM analysis of JMAG software. From the evaluation results, the configurations of reference model design are compared with the proposed design by using the three methods of motor design optimization showed the best characteristics for performance of motor investigation design.

In cosmology dark energy and dark matter are included in the ΛCDM model, but they are still completely unknown. Because in black holes Lorentz invariance seems not to be applicable for curved space-time, we introduce a model for a reduced speed of light in black holes due to quantum gravity effects and the Heisenberg uncertainty relation. Then black holes are a source for a scalar field with dark energy characteristics. This model has no information paradox for black holes because particles / radiation entering the black hole are redshifted in their wavelength that far that the wavelength has the size of the Schwarzschild radius and thus they are in some way "frozen" in the black hole. We show that the scalar field also has characteristics of dark matter shortly after Planck time, when we use a Big Bounce model. This model also presents an alternative to cosmological inflation with the possibility to solve the flatness and horizon problem and the problem of density fluctuations.

Abstract: Agriculture uses plastic products for containers, packaging, tunnels, drip irrigation tub-ing, mulches. Large amounts of plastics are used as mulches on the soil surface for vegetable pro-duction (tomato, cucumber, watermelon, strawberry, vine) to reduce the weed competition, in-crease water and fertilizer use efficiency and enhance crop yield. Portugal uses around 4,500 t/year of polyethylene plastic to cover approximately 23,000 ha of agricultural land and only a small amount is recovered for recycling or secondary uses because of dirt with soil, vegetation, pesticide and fertilizers. Cleaning and decontaminating polyethylene mulch are costly and commercial technology is often not accessible nor economically viable in the current economic Portuguese situation. Most plastic mulch is composed of polyethylene that degrades slowly and produces a large quantity of residues in soil with negative impact in the environment. In the present study, the effects of long-term cultivation of blueberry using green 100% high density polyethylene mulch, in the south Portugal were evaluated for soil chemical and biological changes. High density green plastic mulch did not contaminate the topsoil with di(2-ethylhexyl) phthalate and heavy metals, buttotal nitrogen and organic carbon concentrations, electric conductivity and microbial activity were reduced in the planting row compared with bare soil, without mulching. Further-more, the presence of plastic mulch did not affect negatively the presence of nematodes, and the Rhabditida (bacterial feeders) increased in the planting and covered row.

To map Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV 2) spreading and evaluate immune responses variations against this virus, it was essential to locally set up efficient serological tests. The SARS-CoV2 immunogenic proteins were very expensive and not affordable mainly for Low and Middle Income Countries (LMICs). For this purpose, the commonly used antigen, Re-ceptor-Binding Domain (RBD) of Spike S1 protein (S1RBD), was produced using the the Baculovirus Expression Vector System (BEVS) . During the current study, the expression of S1RBD was monitored using western blot under different culture conditions. Different parameters were studied: Multiplicity Of Infection (MOI), cell density at infection and harvest time. Hence, optimal conditions for efficient S1RBD production were identified: MOI 3; cell density at infection 2-3x 106 cells/mL and time post-infection (tpi or harvest time) of 72h and 72-96 h successively for expression in shake-flasks and 7L-bioreactor. A high production yield of S1RBD varying between 4mg and 70 mg per liter of crude cell culture supernatant was achieved, respectively, in shake-flasks and in 7L-bioreactor. Moreover, the produced S1RBD showed an excellent antigenicity potential against COVID-19 patient sera evaluated by western blot. Thus, additional serological assays, such as ELISA, were developed using the purified S1RDB (published by other research groups).

Fluorophores with a tetraphenylethylene (TPE) core are attracting increasing interest because of their aggregation-induced emission (AIE) behaviour, which makes them particularly suitable when dispersed in thin-layer films. We propose the synthesis and use of a novel TPE fluorophore (hereafter called TPE-BPAN) decorated with two dimethylamino push groups and a 4-biphenylacetonitrile pull moiety. In tetrahydrofuran solutions, TPE-BPAN showed a broad absorption spectrum, and an intense emission is observed when a non-solvent as water is added in amounts of 70% and above. We selected and synthetized five different polymer matrices for TPE-BPAN with decreasing polarity: a) poly(methylmetacrylate) homopolymer (PMMA); b), c), and d) three copolymers of methyl methacrylate and cyclohexyl methacrylate at different compositions (P(MMA-co-CHMA) 75:25, 50:50, 25:75 mol%); e) poly(cyclohexyl methacrylate) homopolymer (PCHMA). The presence of a less polar comonomer as cyclohexyl methacrylate appeared to enhance the emission behaviour of TPE-BPAN, which displayed the highest quantum yield (QY) in P(MMA-co-CHMA) 75:25 in all the range of concentration studied from 0.4 wt.% to 2.0 wt.%. Further reduction in polarity lowered QY to the values of PMMA films; also, lower adhesion to the glass and a marked fragility of the films were observed. Referring to the P(MMA-co-CHMA) 75:25 films, QY values decreased from over 40% at 0.4 wt.% to about 30% at 2.0 wt.%, which is still helpful for energy harvesting applications such as luminescent solar concentrators (LSC). LSC performances were not significantly affected by the matrix's lower polarity and resulted in around one-third of the state-of-the-art due to the lower QY of TPE-BPAN. The theoretical investigation on density functional theory (DFT) clarified the origin of the observed AIE and the role played by the environment in modulating the photophysical behaviour.

The aim of this study was to investigate the role of DNA methylation in the regulation of in vitro and in vivo cartilage formation. Based on the data of an RNA chip-assay performed on chondrifying BMP2-overexpressing C3H10T1/2 cells, the relative expression of Tet1 (tet methylcytosine dioxygenase 1), Dnmt3a (DNA methyltransferase 3) and Ogt (O-linked N-acetylglucosamine transferase) genes was examined with RT-qPCR in mouse cell-line based and primary micromass cultures. RNA probes for in situ hybridization were used on frozen sections of 15-day-old mouse embryos. DNA methylation was inhibited with 5-azacytidine during culturing. We found very strong but gradually decreasing expression of Tet1 throughout the entire course of in vitro cartilage differentiation along with strong signals in the cartilaginous embryonic skeleton. Dnmt3a and Ogt expressions did not show significant changes with RT-qPCR and gave weak in situ hybridization signals. Inhibition of DNA methylation applied during early stages of differentiation reduced cartilage-specific gene expression and cartilage formation. In contrast, it had stimulatory effect when added to differentiated chondrocytes. Our results indicate that the DNA demethylation-inducing Tet1 is a significant epigenetic factor of chondrogenesis, and inhibition of DNA methylation exerts distinct effects in different phases of in vitro cartilage formation.

In the current manuscript we assess to what extent X-ray photoelectron spectroscopy is a suitable tool for probing the dipoles formed at interfaces between self-assembled monolayers and metal substrates. To that aim, we perform dispersion-corrected, slab-type band-structure calculations on a number of biphenyl-based systems bonded to a Au(111) surface via different docking groups. In addition to changing the docking chemistry (and the associated interface dipoles), also the impacts of polar tail-group substituents and varying dipole densities are investigated. We find that for densely-packed monolayers the shifts of the peak positions of the simulated XP-spectra are a direct measure for the interface dipoles. In the absence of polar tail-group substituents they also directly correlate with adsorption-induced work-function changes. At reduced dipole-densities this correlation deteriorates, as work function measurements probe the difference between the Fermi-level of the substrate and the electrostatic energy far above the interface, while core level shifts are determined by the local electrostatic energy in the region of the atom from which the photoelectron is excited.

This paper addresses the issues of how we can quantify structural information for nonparametric distributions and how we can detect its changes. Structural information refers to an index for a global understanding of a data distribution. When we consider the problem of clustering using a parametric model such as a Gaussian mixture model, the number of mixture components (clusters) can be thought of as structural information in the model. However, there does not exist any notion of structural information for nonparametric modeling of data. In this paper we introduce a novel notion of {\em kernel complexity} (KC) as structural information in the nonparametric setting. The key idea of KC is to combine the information bias inspired by the Gini index with the information quantity measured in terms of the normalized maximum likelihood (NML) code length. We empirically show that KC has a property similar to the number of clusters in a parametric model. We further propose a framework for structural change detection with KC in nonparametric distributions. With synthetic and real data sets we empirically demonstrate that our framework enables us to detect structural changes underlying the data and their early warning signals.

With reference to Planck scale, Mach’s relation, increasing support for large scale cosmic anisotropy and preferred directions and by introducing two new parameters Gamma and Beta, right from the beginning of Planck scale, we make an attempt to estimate ordinary matter density ratio, dark matter density ratio, mass, radius, temperature, age and expansion velocity (from and about the baby universe in all directions). We would like suggest that, from the beginning of Planck scale, 1) Dark matter can be considered as a kind of cosmic foam responsible for formation of galaxies. 2) Cosmic angular velocity is directly proportional to squared cosmic temperature. 3) Ratio of critical temperature to actual temperature plays a heuristic role in understanding ordinary and dark matter density ratios. 4) Cosmic expansion velocity increases with decreasing total matter density ratio. 5) There is no need to consider dark energy for understanding cosmic acceleration.

Thresholding is considered as a statistical-decision making theory which can lessen the average error incurred in allocating pixels to two or more groups. The traditional Bayes decision rule can be applied with the prior knowledge of the Probability Density Function (PDF) of each class. It is surmised that a threshold resulting in the best class separation is the optimal one. In this paper, Otsu’s thresholding for image segmentation has been implemented. The well-known Otsu’s method is to learn a threshold that can maximize the between-class variance or equivalently make light of the within-class variance of the entire image. At first, a color image of a tree is taken. After that, the image is transformed into a grayscale image. Then in the first part, two-level thresholding is conducted, and later on, three-level thresholding is also applied. Again, two-level thresholding, as well as three level thresholding, are also applied to some other images. Finally, the comparison is made between two level thresholding and three level thresholding

With reference to Planck scale, Mach's relation and by introducing two new parameters Gamma and Beta, right from the beginning of Planck scale, we make an attempt to estimate ordinary matter density ratio, dark matter density ratio, mass, radius, temperature, age and expansion velocity (from and about the Planck mass in all directions). In analogy with currently believed cosmic acceleration, with a decreasing trend of total matter density ratio, cosmic expansion velocity can be shown to be increasing. By considering $H_0\cong 70$ km/sec/Mpc, estimated current cosmic mass, radius, total matter density, expansion velocity, temperature and age are: $4.3352\times {10}^{53}\mathrm{kg},$ $3.207\times {10}^{26}\mathrm{m},$ $3.138\times {10}^{-27}\mathrm{kg}{.\mathrm{m}}^{-3},$ $2.43c,$ $2.721\mathrm{K}$ and $19.78\mathrm{Billion}\mathrm{years}$ respectively. Point to be noted is that, with reference to Planck scale, cosmic temperature seems to be redshifted by a factor ${\left(Z_T\right)}_t\cong \sqrt{1+\ln \left(H_{pl}/H_t\right)}-1$ where $\left(H_{pl},H_t\right)$ represent Planck scale and time dependent Hubble parameters respectively. As a peculiar case, considering the equality of current Hubble parameter and current angular velocity, current cosmic rotational kinetic energy can be estimated to be 0.667 times the current critical energy. It needs further study.

Abstract: : 2,3-dihydro-5,6,7,8-tetranitro-1,4-benzodioxine (TNBD), molecular formula =C8H4N4O10 is a completely nitrated in aromatic ring 1,4-benzodioxane derivative. The con-venient method of TNBD synthesis was developed (yield=81 %). The detailed structure of this compound has been investigated by X-ray crystallography. The results of differential thermal analysis (DTA) obtained with twice re-crystallized material showed onset at 247 and isoterm at 288 0C, with further total degradation at 300 0C. The experimental density 1,85 g/cm3 of TNBD was determined by X-ray crystallography. The spectral properties of TNBD (NMR, FT-IR, Ra-man) were explored. The detonation properties of TNBD calculated by EXPLO 5 code was slightly superior in comparison to standard high energy material - tetryl (detonation velocity of TNBD - 7727 m/s; detonation pressure - 278 kbar; tetryl – 7570 m/s and 226.4 kbar at 1.614 g/cm3, or 260 kbar at higher density - 1.71 g/cm3. The obtained preliminary results might suggest TNBD can be a potential thermostable high energy and density material (HEDM).

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&amp;M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

This study explores optimizing Synthetic Aperture Radar (SAR) satellite constellation scheduling for multi-imaging missions in densely targeted areas using an in-house developed Modified Dynamic Programming (MDP) algorithm. By employing Mixed-Integer Linear Programming (MILP) to define the mission planning problem, the research aims to maximize observation of high-value targets within restricted planning horizons. Numerical simulations, covering a wide range of target numbers and satellite configurations, reveal the MDP algorithm’s superior mission allocation efficiency, enhanced success rates, and reduced revisit times, compared to the Greedy algorithm. The findings underscore the MDP algorithm’s improved operational efficiency and planning robustness for complex imaging tasks, demonstrating significant advancements over traditional approaches.

The hard open problem of finding the lower bound for the Fokker Planck Kolmogorov’s time-dependent controller parameter probability density function is addressed for the first time in literature in this work. This revolutionary exposition will put control theory and other related inter-disciplinary fields to a higher level towards contemporary control theory. Notably, based on the influential role of control theory in both engineering and industry, this paper will be of great value to all engineering and industry professionals who seek to know more about advanced trends within control theory settings. On the other remit of the spectrum, Fokker Planck Kolmogorov(FPK) equations are of high importance to physicists as well as mathematicians, based on their multiple applicability to multi-interdisciplinary fields of human knowledge, and beyond. So, this by default adds more taste and credibility to this study. Concluding thoughts are included at the end of the work along with a difficult outstanding problem and the direction of future work.

This work is the first in literature to tackle the difficult open problem of determining the upper bound and threshold theorem for the TDCDP (time-dependent controller parameter) of the (Fokker Planck Kolmogorov) probability density function. This revolutionary exposition will put control theory and other related inter-disciplinary fields to a higher level towards contemporary control theory. Notably, based on the influential role of control theory in both engineering and industry, this paper will be of great value to all engineering and industry professionals who seek to know more about advanced trends within control theory settings. On the other remit of the spectrum, Fokker Planck Kolmogorov(FPK) equations are of high importance to physicists as well as mathematicians, based on their multiple applicability to information theory, graph theory, data science, finance, economics, and beyond. So, this by default adds more taste and credibility to this study. This leads by nature to introducing a different flavor to this ground-breaking research by highlighting the impact of Fokker Planck Kolmogorov(FPK) to revolutionize crypocurrency,which have received its name because it uses encryption to verify transactions, a new debatable digital payment system that doesn't rely on banks to verify transactions. It’s a peer-to-peer system that can enable anyone anywhere to send and receive payments. The paper ends with closing remarks combined with some challenging open problems and the next phase of research.

Two pre-pulses focused at different positions and at different time moments were used to enhance THz emission generated by the main pulse. The emission of THz radiation from air breakdown regions of focused ultrashort fs-laser pulses (800 nm/35 fs) at shockwave front prepared by pre-pulses was investigated, and a 3D spatio-temporal control was established for the most intense emission. The laser pulse-induced air breakdown forms a ~120 micrometers-long focal volume and generates a shockwave that delivers denser air into the focal region of the main pulse for enhanced generation of THz radiation at 0.1-2.5 THz spectral window. The intensity of pre- and main-pulses was at the tunneling ionisation intensities (1-3)x10¹⁶ W/cm² and corresponded to sub-critical (transparent) plasma in air. Polarisation analysis revealed that the orientation of the air density gradients generated by pre-pulses and their time-space placement defined the ellipticity of the generated THz electrical field. The rotational electric current is the origin of THz radiation. The current is created by non-parallel gradients of electron density and temperature. Scaling dependencies of THz emission control are established.

Bipolar disorder is a severe mood disorder and is one of the top 20 reasons of disability in the world. It causes a huge burden on society. In this study, the prediction models of bipolar disorder were constructed based on the concept of knowledge distillation. The input data consisted of patients of bipolar disorder and matched controls, all of which were selected from the open database MIMIC. The method of kernel density estimation (KDE) was exploited to generate probability density functions (PDF) which identify distributions of input data. The PDF values referred to as the soft labels were combined with the input data to construct the prediction models of bipolar disorder using decision tree and artificial neural network respectively. According to the evaluation results, indicators for identifying positive samples of bipolar disorder were improved. Meanwhile, the indicators for identifying negative samples have also been advanced. In addition, the branching attributes selected by the decision trees can be mapped back to specific disease diagnoses, which are all associated with bipolar disorder. In conclusion, using KDE to generate the soft label information of the input data can make knowledge distillation work and has improved the performances of prediction models for bipolar disorder.

Microarray patches (MAPs) have the potential to be a safer, more acceptable, easier to use, and more cost-effective means for the administration of vaccines than injection by needle and syringe. Here, we report findings from a randomized, partially double-blind, placebo-controlled Phase I trial using the Vaxxas high-density MAP (HD-MAP) to deliver a measles rubella (MR) vaccine. Healthy adults (N = 63, age 18–50 years) were randomly assigned 1:1:1:1 to four groups: uncoated (placebo) HD-MAPs, low-dose MR HD-MAPs (~3,100 median cell-culture infectious dose [CCID50] measles, ~4,300 CCID50 rubella); high dose MR-HD-MAPs (~9,300 CCID50 measles, ~12,900 CCID50 rubella); or a sub-cutaneous (SC) injection of an approved MR vaccine, MR-Vac (≥1,000 CCID50 per virus). The MR vaccines were stable and remained viable on HD-MAPs when stored at 2–8°C for at least 24 months. When MR HD-MAPs stored at 2–8°C for 24 months were transferred to 40°C for 3 days in a controlled temperature excursion, loss of potency was minimal, and MR HD-MAPs still met World Health Organisation (WHO) specifications. MR HD-MAP vaccination was safe and well-tolerated; any systemic or local adverse events (AEs) were mild or moderate. Similar levels of binding and neutralizing antibodies to measles and rubella were induced by low-dose and high-dose MR HD-MAPs and MR-Vac. The neutralizing antibody seroconversion rates at day 28 after vaccination for the low-dose HD-MAP, high-dose HD-MAP and MR-Vac groups were 37.5%, 18.8% and 35.7% respectively for measles and 37.5%, 25.0% and 35.7% respectively for rubella. Most participants were seropositive for measles and rubella antibodies at baseline, which appeared to negatively impact the number of participants that seroconverted to vaccines delivered by either route. The data reported here suggest HD-MAPs could be a valuable means for delivering MR-vaccine to hard-to-reach populations and support further development. Clinical trial registry number: ACTRN12621000820808.

The sensitivity of exercise ECG is marginally sufficient for detection of mild reduction of coronary blood flow in patients with early coronary atherosclerosis. Here we describe the application of new technique of ECG registration/analysis – ultrahigh resolution ECG (UHR ECG) – for early detection of myocardial ischemia (MIS). The utility of UHR ECG vs. conventional ECG (C ECG) was tested in anesthetized rats and pigs. Transmural MIS was induced in rats by the ligation of the left coronary artery (CA). In pigs, subendocardial ischemia of variable extent was produced by stepwise inflation of balloon within the right CA causing 25-100% reduction of its lumen. In rats, a reduction in power spectral density (PSD) in high-frequency (HF) channel of UHR ECG was registered at 60 s after ischemia (power 0.81±0.14 vs. 1.25±0.12 mW at baseline, p<0.01). This was not accompanied by any ST segment elevation on C ECG. In pigs, PSD in HF channel of UHR ECG was significantly decreased at 25% reduction of CA lumen, while ST segment on C ECG remained unchanged. In conclusion, UHR ECG enabled earlier detection of transmural MIS compared to C ECG. PSD in HF-channel of UHR ECG demonstrated greater sensitivity in the settings of subendocardial ischemia.

Organic light-emitting diodes (OLEDs) are energy-efficient; however, the coordinating ligand can affect their stability. Sky-blue phosphorescent Pt(II) complexes with a C^N chelate, fluorinated-dbi (dbi = [1-(2,4-diisopropyldibenzo[b,d]furan-3-yl)-2-phenyl-1H-imidazole]), and acetylactonate (acac)(1)/picolinate (pic)(2) ancillary ligands were synthesized. The molecular structures were characterized using various spectroscopic methods. The Pt(II) coordination sphere in 2 exhibited a distorted square-planar geometry, with several intra- and inter-molecular interactions involving Cπ⋯H/Cπ⋯Cπ stacking. Complex 1 emitted bright sky-blue light (λmax = 485 nm) with a moderate photoluminescent quantum efficiency of 0.37 and short decay time (6.1 µs) compared to those of 2. Time-dependent density functional theory calculations suggested that the electronic transition of 1 arose from ligand(C^N)-centered π–π* transitions combined with metal-to-ligand charge transfer transitions (MLCT), whereas that of 2 arose from MLCT and ligand(C^N)-to-ligand(pic) charge transfer (LLCT), with minimal contribution from the C^N chelate to the lowest unoccupied molecular orbital. Multi-layered phosphorescent OLEDs using 1 as a dopant and a mixed host, 3,3-di(9H-carbazol-9-yl)-1,1-biphenyl:3-di(9H-carbazol-9-yl)-1,1-biphenyl (mCBP)/9-(3’-carbazol-9-yl-5-cyano-biphenyl-3-yl)-9H-carbazole-3-carbonitrile (CNmCBPCN) were successfully fabricated. At a 10% doping of 1, a current efficiency of 13.6 cd A−1 and external quantum efficiency of 8.4 % at 100 cd m−2 were achieved. These results show that the ancillary ligand in phosphorescent Pt(II) complexes must be considered.

PTB7-Th is an important donor copolymer used in construction of many organic devices and other industrial applications. In this work, we investigate the structure and energetics of PTB7-Th. We employ density functional theory (DFT) (B3LYP), dispersion corrected DFT (B3LYP-D3) and long-range corrected DFT (CAM-B3LYP, LC-BLYP, and ωB97xD) to analyze the conformational structures and their corresponding energies to determine the lowest energy state of PTB7-Th. The role of the alkane side chains is carefully investigated. Our findings indicate that, when branched ethylhexyl side chains are present, the lowest energy structure of PTB7-Th has fluorine in the same plane and the same side as the double bonded oxygen in the TT-CF part of the monomer and S-C-C-S dihedral angles along the chain backbone are cis-like having values in the range of 20-30 degrees in most cases. Without these side chains the polymer, not unexpectedly, has many near conformational degeneracies.

The Sulfur Dioxide (SO2) compound is a primary environmental pollutant worldwide, whereas elemental Sulfur (S) is a global commodity possessing a variety of industrial as well as commercial functions. The chemical relationship between poisonous SO2 and commercially viable elemental S has motivated this investigation using Density Functional Theory calculation of the relative transition state barriers for the 2-step Dehydro-sulfurization oxidation-reduction reaction. Additionally, doubly-charged nanoscale platelet Molybdenum Disulfide (MoS2), Armchair (6,6) Carbon Nanotube, 28-atom Graphene nanoflake (GR-28), and Fullerene C-60 are utilized as catalysts. The optimal heterogeneous and homogeneous catalysis pathways of the 2-step oxidation-reduction from SO2 to elemental S are further inspired by the biomimicry of the honeybee species multi-step bio-catalysis of pollen conversion to organic honey. Potential applications include environmental depollution, the mining of elemental sulfur, and the functionalization of novel technologies such as the recently patented aerial and amphibious Lynchpin TM drones.

The Sulfur Dioxide (SO2) compound is a primary environmental pollutant worldwide, whereas elemental Sulfur (S) is a global commodity possessing a variety of industrial as well as commercial functions. The chemical relationship between poisonous SO2 and commercially viable elemental S has motivated this investigation using Density Functional Theory calculation of the relative transition state barriers for the 2-step Dehydro-sulfurization oxidation-reduction reaction. Additionally, doubly-charged nanoscale platelet Molybdenum Disulfide (MoS2), Armchair (6,6) Carbon Nanotube, 28-atom Graphene nanoflake (GR-28), and Fullerene C-60 are utilized as catalysts. The optimal heterogeneous and homogeneous catalysis pathways of the 2-step oxidation-reduction from SO2 to elemental S are further inspired by the biomimicry of the honeybee species multi-step bio-catalysis of pollen conversion to organic honey. Potential applications include environmental depollution, the mining of elemental sulfur, and the functionalization of novel technologies such as the recently patented aerial and amphibious Lynchpin TM drones.