A proof is given showing the Collatz Conjecture is true for all positive integers. The proof was possible once the perspective of the proof was changed from looking at the pattern of the positive integers to looking at the conjecture rules. The conjecture rule for even numbers organizes all positive integers into unique sets and the rule for odd numbers interconnects the unique sets into dendritic pathways to “1.” Infinite loops, other than the minor 4-2-1 loop after reaching “1,” and pathways to infinity are shown to be mathematically impossible. The proof predicted a general equation that shows all positive integers ultimately reach a final value of “1," and calculates the values and locations of the odd positive integers during the iterations for each tested positive integer.

The accurate state of health (SOH) estimation of lithium-ion batteries (LIBs) during operation is crucial to ensure optimal performance, prolonging battery life and preventing unexpected failure or safety hazards. This work presents a storage and performance optimised deep learning approach to predict the capacity based SOH of LIBs using raw sensor data from partial charging curves under constant current condition. The proposed model is based on a combination of a 1-dimensional convolutional and long-short term memory neural network and processes time, voltage and incremental capacity of partial charging curves as time series. The model is cross-validated on different aging scenarios reaching an overall MAE = 0.418% and RMSE = 0.531%, promising an accurate SOH estimation of LIBs under varying usage and environmental conditions in a real world application.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

This paper describes a system that is used to gather data from Smart Home sensors measuring energy consumption, analyze and predict future consumption by using machine learning algorithm for prediction. It focuses on the architecture of the system as well as the need for such system to exist in practice – why the consumption should be measured at all and how that measurement can be put to good use for achieving energy efficiency.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Mass hauling operations play central roles in construction projects. They typically use many haulers that consume large amounts of energy and emit significant quantities of CO₂. However, practical methods for estimating the energy consumption and CO₂ emissions of such operations during project planning are lacking. This paper presents a detailed model for estimating the energy consumption and CO₂ emissions of mass haulers that integrates the mass hauling plan with a set of predictive equations. The mass hauling plan is generated using a planning program such as DynaRoad in conjunction with data on the productivity of selected haulers and the amount of material to be hauled during cutting, filling, borrowing, and disposal operations. This plan is then used as input for estimating the energy consumption and CO₂ emissions of the selected hauling fleet. The proposed model will help planners to assess the energy and environmental performance of mass hauling plans, and to select hauler and fleet configurations that will minimize these quantities. The model was applied in a case study, demonstrating that it can reliably predict energy consumption, CO₂ emissions, and hauler productivity as functions of the hauling distance for individual haulers and entire hauling fleets.

Managing Water, Energy, and Food (WEF) resources within socio-environmental systems demands innovative strategies that provide decision-makers with actionable insights. This article explores the challenges and potential solutions of employing Focus Maps and choremes as a novel approach for assessing anthropogenic impacts and enhancing the visualization of the WEF Nexus in specific geographic areas. By integrating geospatial data, multi-criteria analysis, and involving stakeholders, our research aims to develop Choreomatic Focus Maps (CFMs) that offer a comprehensive spatial representation of the WEF Nexus, facilitating better-informed decision-making at the community level. Our current work outlines visualization of WEF Nexus, as an initial stages of creating CFMs through a detailed step-by-step process. This includes identifying the main drivers for WEF nexus, such as anthropogenic activities and their distribution, evaluating environmental factors, linking anthropogenic impact with environmental indicators over time, and conducting on-site validation. Our focus is on advancing through these crucial steps, particularly emphasizing field validation within the Local Decision-Makers Tools, visualized here by using Focus Maps. This phase is vital for ensuring our approach is grounded in reality and meets the needs of the communities within the Danube Delta region. By doing so, we aim to provide a visual summary of the WEF Nexus that not only captures the complexity of this fragile ecosystem but also incorporates local insights and priorities, identifying key areas where human activities have significant impacts.

Ammonia can be considered a relevant compound in the future energy sector, playing a significant role as an energy carrier, storage, or carbon-free fuel. However, the production of this molecule has a high energy demand, and the use of natural gas, which is not free of controversy due to the accidental leakage into the atmosphere produced during extraction and the fact that it is a non-renewable source, contributes to increasing greenhouse gas emissions. Reducing the process’s energy demand and carbon footprint will be essential to making ammonia a clear alternative for a carbon-free economy. Given the vast experience in ammonia production and handling, this gas seems to be the logical step forward in the evolution of the energy sector. However, the current uncertainty in the global market requires cautiousness in decision-making. Several factors may impact economic growth and human welfare, thus needing a careful assessment before taking any transcendental decisions that could affect worldwide energy prices and raw material availability.

Polar stratospheric clouds (PSCs) form in polar regions typically between 15 and 25 km, when the local temperature is sufficiently low. PSCs play an important role in the ozone chemistry and the dehydration and denitrification of the stratosphere. Lidars with a depolarization channel may be used to detect and classify different classes of PSCs. The main PSC classes are water ice, nitric acid trihydrate (NAT) and supercooled ternary solutions (STS), the latter being liquid droplets consisting of water, nitric acid and sulphuric acid. PSCs have been observed at the lidar observatory at Concordia Station from 2014 on. The harsh environmental conditions at Concordia during winter render successful lidar operation difficult. In order to facilitate the operation of the observatory several measures have been put in place to achieve an almost complete remote control of the system. PSC occurrence is strongly correlated with local temperatures and is affected by dynamics, as the PSC coverage during the observation season shows.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

Sechium compositum (Cucurbitaceae) is a wild species that is distributed in the Soconusco region, Chiapas, Mexico, and the border with Guatemala. This species has an intangible biochemical value resulting from the pharmacological relevance of its secondary metabolites. However, as a consequence of the lack of knowledge about its importance, it is being displaced from its habitat at an accelerated rate, incurring the risk of genetic loss. Therefore, an in vitro culture protocol with two experimental phases was evaluated to propagate, conserve, and regenerate this species. The first phases considered the multiplication of seedlings, adding seven concentrations (0.1, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2 mg mL-1) of 6-benzylaminopurine (BA) and thidiazuron (TDZ) and evaluating the number of buds, shoots, and seedling height. The best multiplication response was recorded with 0.1, 0.2, 0.4, and 1.0 mg L-1 of BA and 0.1 mg L-1 of TDZ, as well as the MS base culture medium. With 0.1 mg L-1 of BA, 52-mm height, 1.36 shoots, and 9.22 buds were obtained, surpassing the MS control (MS culture medium alone); likewise, twice more roots (80%) and a 14% reduction in the bud structure were packed in 50 repetitions. The second phase consisted of inducing callus formation from stem and leaf explants through the addition of 0.5, 1.0, and 2.0 mg L-1 of TDZ and 2,4-Dichlorophenoxyacetic acid (2,4-D) to the medium. The results demonstrated that the induction of callogenesis in S. compositum has a better start from the stem in a medium with 2.0 mg L-1 of 2,4-D, whose value was 4.89 —equivalent to 97.8% callus formation around the explant. The addition of 500 mg L-1 of polyvinylpyrrolidone (PVP) is also suggested to reduce oxidation. This protocol represents a significant advance in the conservation, multiplication, and callogenesis of S. compositum and contributes to its rescue and revaluation in the face of the danger of extinction.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

Halide perovskite materials gain enormous attention for their semiconducting properties, higher power conversion efficiency and potential applications in a wide range field of studies along with their two key limitations: stability and toxicity. In spite of great progress made on the halide perovskites and many promising research developments, overcoming these limitations is not realized yet. Therefore, coordination engineering of new framework for obtaining alternative new halide perovskite materials and fundamental understanding of the coordination chemistry and electronic interactions forming the structure of these newly engineered halide perovskite materials might be one way in order to overcome the issues related to both stability and toxicity. In this review, the current development of halide perovskite families, both lead halide perovskites and lead free halide perovskites followed by coordination engineering of the new frameworks to engineer new halide perovskite materials will be reviewed comprehensively. Moreover, all the concerns of the fundamental ideas of coordination chemistry and electronic interactions that are keys in forming the halide perovskite structures are discussed in detail and form the main aim of this review. Interestingly, we also discuss recent potential energy applications beyond photovoltaic and this review has completed with an essential and open question: ‘what could happen in the future of halide perovskites?’ in order to excite commercial enterprises and research institutions again as well as to get motivating new predictions on the future continuity of this field.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

This research aimed to investigate the relationship between climate policy uncertainty (CPU), clean energy (ENERGY), carbon emission allowance prices (CARBON), and Bitcoin returns (BTC) for the period from August 2012 to August 2022. The empirical analysis strategies utilized in this study included the Fourier Bootstrap ARDL long-term coefficient estimator, Fourier Granger Causality, and Fourier Toda Yamamoto Causality methods. Following the confirmation of cointegration among the variables, we observed a positive relationship between BTC and CARBON, a positive relationship between BTC and CPU, and a negative relationship between BTC and ENERGY. In terms of causal associations, we identified one-way causality running from CARBON to BTC, BTC to CPU, and BTC to the ENERGY variable. The study underscores the potential benefits and revenue opportunities for investors seeking diversified investment strategies in light of climate change concerns. Furthermore, it suggests actionable strategies for policymakers, such as implementing carbon taxes and educational campaigns, to foster a transition towards clean energy sources within the cryptocurrency mining sector and thereby mitigate environmental impacts.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

A hybrid organic molecules as ligands and inorganic NCs in this research combines the chemical properties of organic semiconductors with the chemical stability of inor- ganic nanoparticles like PbS. It is possible to improve the ligand exchange and PbS-NCs' distribution by adding Amino phynel anchor group to TIPs-pentacene and Carboxylic anchor group to Tetraphenylporphyrin molecules. By adding anchor groups to one or two sides of these molecules, they would convert the molecules to ecient ligands to obtain superlattice coupled organic-inorganic nanostrcuture semicondcutor layers (COINs). Adding on side group would cap the PbS nanoparticles while adding two an- chor group would play a linker role between two PbS NCs. This morophology enhance- ment paves the way to manipulate the physical properties of the COINs and fabricate solar cells. Singlet ssion phenomena demonstrates pentacene molecule's advantage for high eciency in organic solar cells and its ability to overcome the Schockley-Queisser limit. Ultraviolet photo-emission spectroscopy (UPS) determines the highest occupied molecular orbital (HOMO) and the work function of COINs, while the lowest unoccu- pied molecular orbital (LUMO) of COINs were calculated subsequently by adding both the exciton binding energy and the optical band gap to the measured HOMO energy. The current versus voltage characteristics and impedance spectroscopy were studied for these molecules as well.

Compressed carbon dioxide energy storage (CCES) offers several benefits over other existing energy storage systems, including ease of liquefaction, high energy storage density, and environmental friendliness. As a result, the research progress, economic and technological feasibility, and system operation of the CCES system are all discussed in depth in this study. The system evaluation method is summarized and the compressed carbon dioxide storage is analyzed, and the performance optimization direction of the compressed carbon dioxide energy storage technology is discussed. When the overall performance of a transcritical CCES system, a supercritical CCES system and a liquid CCES system are compared, it is discovered that the supercritical CCES system has better thermodynamic characteristics and a simpler system configuration, making it suitable for large-scale development and use. The goal of the CCES system's future development is to create a design with an optimum compression and expansion ratio, a more precise analysis and system model, and multi-field coupling. This review's discussion serves as a guide for the best design and use of the CCES system.

Abstract: Field studies with large-stemmed plants Artemisia dubia (wormwood) have been carried out at Vėžaičiai Branch LAMMC since 2018. According to three years of experimental results, annual dry matter (DM) yield varied from 7.94 to 10.14 t ha-1. Growing conditions, nitrogen ap-plication level and harvesting time had significant impacts on Artemisia dubia productivity. This article presents the results of research on preparation and use of Artemisia dubia biomass for en-ergy conversion and evaluation of technological-technical and environmental parameters of these plants utilization for solid biofuel. For experiments were used 6 variants of Artemisia dubia samples, which were grown in 2021: plants were cut three times and two fertilization options were used: (1) no fertilization and (2) fertilization with 180 kg ha-1 of nitrogen fertilizer. These harvested plants were chopped, milled and were pressed into the pellets. The physi-cal-mechanical characteristics (mоisture content, density and strength) of Artemisia dubia pellets were investigated. During this study, it was found that the density in dry mass (DM) of pellets ranged from 1119.86 to 1192.44 kg m-3. The pellet moisture content ranged from 8.80 to 10.49%. After testing of pellet strength, it was found that the pellets which were made from plant bio-mass PK-1-1, were the most resistant to compression, they withstood 560.36 N of pressure. Dry fuel lower heating value (LHV) of pellets was sufficiently high and was very close to pine saw-dust pellets, it varied from 17.46±0.25 MJ kg-1 to 18.14±0.28 MJ kg-1. The ash content of burned pellets ranged from 3.62±0.02% to 6.47±0.09%. Emissions of harmful pollutants – CO2, CO, NOx and unburnt hydrocarbons (CxHy) did not exceed the maximum permissible levels. Summariz-ing the results of investigated properties, cоmbustion and emissiоns of Artemisia dubia pellets, it can be concluded that this biofuel can be used for production of pressed biofuel and it is charac-terized by sufficient high quality, efficient combustion and permissible emissions to the envi-ronment.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

The study aims to explain the different effects between the multiplication, addition, division and subtraction equations. In this sense, multiplication and addition equations develop a new element or fact, meanwhile, division equations express information within the element or fact, subtraction is the selection of element or fact. Furthermore, for a multiplication and addition equation results in the new element or fact, it is necessary to depend on specific physical concepts, without extreme alteration, as it would result in the alteration of the element or fact. It is worth highlighting the importance of fixed values ​​in the equation to describe the specific nature of the element or fact. The study makes it possible to understand open equations (without solutions) in mathematics and physics, in addition to understanding existing equations. The study makes reference to the theory of obligatory necessity and the theory of differences between elements.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

The classification and summarization of online reviews using machine learning and deep learningbased approaches are the subject of this systematic literature review. Consumers, companies, and researchers can now find vital information from online reviews. Automatically categorizing and summarizing these reviews can offer useful information and facilitate decision-making. The purpose of this study is to offer a thorough overview of the current methodology, approaches, and developments in this area. The review concentrates on machine learning-based methods for categorization and summarizing tasks, highlighting their advantages, drawbacks, and new developments. This systematic review provides insights into the most recent methodologies and indicates prospective directions for further investigation by synthesizing the data from a wide range of pertinent research publications

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

Sleep fragmentation (SF) can increase inflammation and production of reactive oxygen species (ROS), leading to metabolic dysfunction. SF is associated with inflammation of adipose tissue and insulin resistance. Several studies suggested that melatonin may have beneficial metabolic effects by activating AMP-activated protein kinase (AMPK). However, it is unclear whether melatonin affects the AMPK signaling pathway in SF-induced metabolic dysfunction. Therefore, we hypothesize that SF induces metabolic impairment and inflammation in white adipose tissue (WAT), as well as altered intracellular homeostasis. We further hypothesize that these conditions could be improved by melatonin treatment. We conducted an experiment using adult male C57BL/6 mice, which were divided into three groups: control, SF, and SF with melatonin treatment (SF+Mel). The SF mice were housed in SF chambers, while the SF+Mel mice received daily oral melatonin. After 12 weeks, glucose tolerance test, insulin tolerance test, adipose tissue inflammation, and AMPK assessments were performed. The SF mice showed increased weight gain, impaired glucose regulation, inflammation, and decreased AMPK in WAT compared to the controls. Melatonin significantly improved these outcomes by mitigating SF-induced metabolic dysfunction, inflammation, and AMPK downregulation in adipose tissue. The therapeutic efficacy of melatonin against cardiometabolic impairments in SF may be due to its ability to restore adipose tissue homeostatic pathways.

Seeds stored for a prolonged period are subject to aging and reduction in germination potential (GP), which will negatively affect seed sales. Rare-earth elements have a synergistic effect on the improvement of seed GP. In this study, we examined the effects of neodymium on biochemical components, the antioxidant protective system, and metabolism-related enzymes during germination of naturally and artificially aged seeds of three wheat cultivars. Seed germination indices, biochemical substance contents, and enzyme activities decreased after seed aging. Soaking seeds in neodymium nitrate solution revived aged wheat seeds at an optimal concentration of 20 µmol/L for 8 h. Soaking in neodymium nitrate solution increased the GP (by 2.25%–60.9%), germination index (by 1.69%–29.2%), and vigor index (by 3.36%–18.7%) of aged seeds. Compared with non-soaked seeds, soaking significantly changed the contents of biochemical substances, and the activities of antioxidant protective enzymes and metabolic enzymes in seedlings were increased. Soaking with neodymium may revive aged seeds by regulating the synthesis of soluble sugars, soluble proteins, chlorophyll, and carotenoids, and decomposing malondialdehyde, in the germinating seed. Root dehydrogenase and amylase showed different responses to the aging modes. The differential responses of root dehydrogenase and amylase may reflect differences in the resistance of enzymes to long-term mild seed aging and short-term severe environmental aging.

We discuss three key points: defining mathematically the notions of phase, symmetry breaking, topological defects and their stability in a formal language of homotopy theory and fiber bundle formalism; postulating and proving two theorems for successive symmetry breaking scenarios in condensed matter physics and cosmology, and demonstrating application of theorems to superfluid Helium 3 and Kibble-Lazarides-Shafi (KLS) walls, supporting and mathematically justifying the results of [Volovik, 2020].

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

Abstract: Social media has become a vital tool in ensuring productivity among Undergraduates, as studies have shown an increased number of users globally. This study assessed the impact of social media usage on undergraduates’ academic performance and working memory. Participants from three different universities such as the University of Georgia (UG), Eastern European University (EEU), and Batumi State University (BSU) completed this study using online google forms. UG and EEU are in the capital city, and BSU is in Batumi City. The study questionnaires were approved by the institutional review board before the data collection. Descriptive analyses were assessed for all study populations, characteristics, frequencies, percentages, means, and standard deviations using Statistical Package for Social Science (SPSS Inc., Chicago, IL, version 25.0 for Windows) software. 41.3% were male students, as most of the participants were foreign students living and studying in Georgia. Male students had the risk of ‘conflict’ with families and friends because of social media. Female students are at increased risk of using social media as an ‘escape’ from negative feelings. 89.7% of students that perform physical activities, considering their academic workload had the risk of preoccupation complaints. 87.9% felt dissatisfied regularly because they wanted to spend more time on social media. Utilization of social media differed based on the characteristics of the participants such as age, gender, and geography. We observed the increase in prevalence of social media addiction, its effect on academic performance and working memory among undergraduate students.

The blended perfluorinated sulfonic acid ionomers are prepared to have equivalent weight (EW) ~1000, 980, and 830. The catalyst layers (CLs) using blended PFSA ionomers with different side chain lengths and EWs are investigated, compared to the CLs utilizing single ionomers. The IEC results indicate that the blended ionomers have the targeted EWs. As a result, it is found that the blended ionomers exhibit higher ion conductivity than the single ionomers at all temperatures due to higher water uptake of the blended ionomers. Even though they have a similar EW, it implies that the blended ionomers have bulk structure to form competent free volume. The blended ionomers with short side chain (SSC) and low EW can help reduce the activation energy due to the enhanced hydrophobic and hydrophilic segregation. In addition, it is observed that the catalyst layers using the blended ionomer form more porous microstructure to help reduce the resistance of oxygen transport and attributes to lower mass transfer loss. This effect is significantly revealed in the fuel cell operation at not the lower temperature (70 °C) and full humidification (100%) but the elevated temperature (80 °C) and lower relative humidity (50 and 75%). The blended ionomer-based catalyst layers with higher water uptake and porous CL structure result in higher fuel cell performance and better mass transport than the single ionomer-based catalyst layers.

South Korea proposed reducing greenhouse gas emissions by 37% compared to the expected emissions by 2030 as the POST-2020 greenhouse gas reduction target. Electric vehicle distribution in the public sector is essential to achieve the carbon dioxide reduction target for transportation. In particular, when buses with internal combustion engines, which travel long distances and contribute substantially to greenhouse gas emissions, are replaced with electric buses, it is expected that greenhouse gas emissions will be significantly reduced. There are three types of electric buses with different power supply systems: a plug-in type in which power is supplied when a plug is inserted, a battery-swapping type in which a battery mounted on top of the vehicle is swapped at a swapping station, and a wireless type in which the battery is wirelessly charged through self-induction at a charging facility installed on the road. Vehicles of each charging type have different advantages and disadvantages. The performance, charging type, battery capacity, and operating environment of electric buses are mutually related parameters that must be considered when introducing such vehicles. Therefore, the optimal charging type must be selected according to the operating environment to enable the widespread use of electric buses. As such, this report proposes the optimal charging type according to the operating environment of public-sector electric vehicles.

Malignant melanoma is a lethal skin cancer containing melanoma-initiating cells (MIC), implicated in tumorigenesis, invasion, and drug resistance, and characterized by elevated expression of stem cell markers, such as CD133. We previously showed that siRNA knockdown of CD133 enhances apoptosis induced by the MEK inhibitor trametinib in melanoma cells. The current study investigates underlying mechanisms of CD133’s anti-apoptotic activity in patient-derived BAKP and POT cells, harboring difficult-to-treat NRASQ61K and NRASQ61R drivers, after CRISPR-Cas9 CD133 knockdown or Dox-inducible expression of CD133. To maintain stable expression of CD133, MACS-sorted CD133(+) positive cells were expanded by ROCK-mediated conditional reprogramming of BAKP melanoma cells (BAKR). BAKR showed increased survival via reduced apoptosis after exposure to trametinib or DTIC, compared to BAKP. CRISPR-Cas9- mediated CD133 knockdown in BAKR cells (BAKR-T3) re-sensitized the cells, while CRISPR-Cas9 knockdown of CD133 in parental BAKP and POT cells even further increased trametinib-induced apoptosis (cleaved PARP) by reducing levels of anti-apoptotic BCL-xL, p-AKT, and p-BAD, and increasing pro-apoptotic BAD and active BAX. Dox-induced CD133 overexpression had the opposite effect, and blocked trametinib-induced apoptosis in both cell lines, coincident with elevated p-AKT, p-BAD, BCL-2 and BCL-xL and decreased levels of the active form of BAX and caspases-3 and -9. The roles of CD133 in AKT and BAD phosphorylation, or in the upregulation of anti-apoptotic BCL-2 family members, was further investigated by AKT knockout with siRNA, or inhibition of BCL-2 family members with navitoclax (ABT-263). Similar to CD133 knockdown, AKT1/2 siRNA knockdown in BAKP cells also reduced p-BAD. CD133 knockdown (T3)-mediated reduction of pBAD levels was equivalent in AKT-knockdown or AKT control cells indicating that CD133 may be upstream of AKT signaling. In BAKP cells treated with trametinib and/or ABT-263, effects of ABT-263 mirrored CD133 knockdown, since levels of active BAX and cleaved-PARP in BAKP-SC (CD133-) cells increased to the same level as that exhibited by BAKP-T3 cells (CD133+). CD133 may therefore activate a survival pathway where 1) increased phosphorylation of AKT induces 2) phosphorylation and inactivation of BAD, 3) decrease in the active form of BAX, and 4) reduction in caspase-mediated PARP cleavage, indicating apoptosis suppression leading to drug resistance in melanomas. Targeting survival pathways by which CD133 may confer chemoresistance in MICs can contribute to development of more effective treatments for patients with high-risk melanoma.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

The thermoelectric generator (TEG) has much potential as a renewable energy technology that could be used in ocean thermal energy conversion (OTEC). This technique employs TEGs and heat exchangers as substitutes for the intricate elements found in conventional OTEC systems, including pressure valves, evaporators, condensers, and turbine generators. By harnessing the temperature difference between warm surface seawater and cold deep seawater, it facilitates the conversion of this thermal gradient into electrical energy. This study used computer simulations to look at and compare three different types of heat exchangers: a cavity-type heat exchanger, a heat exchanger with flat fins, and a heat exchanger with longitudinal vortex generators (LVGs). The objective was to evaluate the influence of these designs on the thermoelectric conversion performance when implemented in OTEC systems. The study's findings indicate that using heat exchanger configurations featuring flat fins, or LVGs, enhances the efficiency of thermal energy transfer from warm seawater to TEGs, resulting in a notable enhancement in the output power of TEGs. Furthermore, the efficiency of TEG thermoelectric conversion is influenced by varying seawater flow rates in relation to the performance of flat fins and LVGs. In contrast to the cavity-type heat exchanger, the utilization of a heat exchanger equipped with flat fins has been found to yield a notable enhancement in the output power of TEGs by approximately 22.92%. Furthermore, this configuration demonstrates a substantial improvement in thermoelectric conversion efficiency, exhibiting an increase of around 40.01%. These improvements are observed under certain conditions pertaining to flow rates and fin heights. Utilizing heat exchangers equipped with LVGs has been found to enhance the output power of TEGs by 13.02% and improve the overall thermoelectric conversion efficiency by 17.72%. These improvements are observed under certain conditions, including specific flow rates, LVG tilt angles, and locations.

Background: Sexual dysfunction is the most common side effect encountered by cervical cancer patients during and after treatment, and rehabilitation strategies are needed to improve their quality of life. A variety of rehabilitation strategies have been reported in previous studies, varying by country, race and even continent. However, the common rehabilitation strategies used by cervical cancer survivors in Tanzania and their outcomes are unknown. The study aimed to unfold sexual rehabilitation strategies and outcome practiced by cervical cancer survivors who experienced sexual dysfunction during and after treatment in North-western Tanzania. Methods: Descriptive qualitative study were employed. Phenomenology study design used with a sample of 7 participants and data corrected via in-depth interview guided by 11 questions. Audiotaped and transcribed to get main themes and sub themes through deductive analysis. Results: Most participants reported inability to achieve an orgasm and low libido and dyspareunia after treatment. Most participants were eagerly to have their sexual activity recovered. However, they were not familiar with any rehabilitation strategy after the experience of sexual dysfunction. Even though, some of the participants attempted various interventions, but all were unsatisfactory leading to a significant decline in sexual interest and activity. Conclusion: Cervical cancer survivors are not familiar with any sexual rehabilitation strategies. Health education concerning various sexual rehabilitation strategies should be provided to survivors during and even after treatment.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

Antimicrobial resistance (AMR) poses a critical global health threat, leading to approximately 1.27 million deaths annually from infectious diseases resistant to existing antibiotics. Factors such as antibiotic misuse and environmental contamination have accelerated AMR, with the COVID-19 pandemic exacerbating the issue due to increased antibiotic usage. However, the development of new antibiotics has stagnated, with only a few approved in recent years, and many facing resistance. Among the priority pathogens identified by the WHO, Pseudomonas aeruginosa stands out as a significant concern due to its multidrug resistance and virulence. P. aeruginosa infections are challenging to treat due to intrinsic and acquired resistance mechanisms, as well as its ability to form biofilms. Additionally, P. aeruginosa produces a plethora of virulence factors, including proteases, siderophores, and toxins, further complicating treatment. Quorum sensing (QS) systems play a crucial role in regulating bacterial physiology and virulence factor expression. P. aeruginosa employs three QS systems, making it an attractive target for quorum quenching (QQ) strategies. Enzymes such as AHL lactonases, acylases, and oxidoreductases have shown promise in inhibiting QS, thus reducing virulence without impacting bacterial growth. Furthermore, natural QS inhibitors produced by various organisms offer potential therapeutic alternatives. Despite promising results in vitro, translating QQ strategies to clinical settings remains challenging. Nevertheless, QQ represents a novel approach in combating multidrug-resistant infections and warrants further investigation as a complementary therapeutic strategy alongside traditional antibiotics. This review summarizes enzymes with Qurorum Quenching activity evaluated against the pathogen P. aeruginosa and their potential applications in combination therapies.

Efficient heat management and control in optical devices, facilitated by advanced thermo-optic materials, is critical for many applications such as photovoltaics, thermal emitters, mode-locked lasers, and optical switches. Here, we investigate the thermo-optic properties of 2D graphene oxide (GO) films by precisely integrating them onto microring resonators (MRRs) with control over the film thicknesses and lengths. We characterize the refractive index, extinction coefficient, thermo-optic coefficient, and thermal conductivity of for the GO films with different layer numbers and degrees of reduction, including reversible reduction and enhanced optical bistability induced by photo-thermal effects. Experimental results show that the thermo-optic properties of 2D GO films vary widely with the degree of reduction, with significant polarization anisotropy, enabling efficient polarization sensitive devices. The versatile thermo-optic response of 2D GO substantially expands the scope of functionalities and devices that can be engineered, making it promising for a diverse range of thermo-optic applications.

Directed energy deposition (DED) parameters were determined for near-β alloy Ti-55511 by employing statistical design of experiments (DOE) methods. Parameters resulting in fully dense freeform deposits were identified using two sequential DOEs. Single laser tracks were printed with several laser power, traverse rate, and powder feed rate settings in an initial DOE to identify promising build parameters. Capture efficiency and effective deposition rate were used to characterize and rank the single track deposits. The best parameters were then used to print solid cube with various X-Y and Z-overlaps (different hatch spacing, HS, and layer thickness, ZS) in a second DOE. Suitable deposition parameters were selected based on cube density and microstructure and were used to fabricate larger tensile samples for mechanical testing. Multiple parameter sets were found to provide dense Ti-55511 deposits with acceptable mechanical properties and parametric models showed statistical significance.

This article presents a description of a new method for solving the factorization problem, based on the gradient descent algorithm. This approach demonstrates significant improvements in efficiency compared to traditional methods proposed in previous research. This article describes a new method for solving the factorization problem, based on the gradient descent algorithm, and demonstrates the transition from algebraic methods to approaches based on functional analysis. The proposed approach not only improves the efficiency of solving the problem but also allows the application of computational algorithms of functional analysis, opening new possibilities for research and optimization.

Transcranial direct current stimulation (tDCS) is acknowledged for its non-invasive modulation of neuronal activity in psychiatric disorders. However, its application in insomnia research yields varied outcomes depending on different tDCS types and patient conditions. Our primary objective is to elucidate its efficiency and uncover the underlying mechanisms in insomnia treatment. We hypothesized that anodal prefrontal cortex stimulation activates glutaminergic projections from the infralimbic cortex (IL) to ventrolateral preoptic area (VLPO) to promote sleep. After administering 0.06 mA of electrical currents for 8 minutes, our results indicate significant non-rapid eye movement (NREM) enhancement in naïve mice within the initial 3 hours post-stimulation, persisting up to 16-24 hours. In the insomnia group, tDCS enhanced NREM sleep bout numbers during acute stress response and improved NREM and REM sleep duration in subsequent acute insomnia. Sleep quality, assessed through NREM delta powers, remains unaffected. Interference of the IL-VLPO pathway, utilizing designer receptors exclusively activated by designer drugs (DREADDs) with the cre-DIO system, partially blocked tDCS's sleep improvement in stress-induced insomnia. This study elucidated that the activation of the IL-VLPO pathway mediates tDCS's effect on stress-induced insomnia. These findings support the understanding of tDCS effects on sleep disturbances, providing valuable insights for future research and clinical applications in sleep therapy.

The gas molecules O2, NO, H2S, CO, CH4 , have been increasingly used for medical purposes. Beside these gas molecules, H2, the smallest diatomic molecule in nature, has become a rising star in gas medicine in the past few decades. As a non-toxic and easily accessible gas, H2 has shown preventive and therapeutic effects on various diseases of the respiratory, cardiovascular, central nervous and other systems, but the mechanisms are still unclear and even controversial, especially the mechanism of H2 as a selective radical scavenger. Mitochondria are the main organelles regulating energy metabolism in living organisms, as well as the main organelle of reactive oxygen species generation and target. We propose that the protective role of H2 may be mainly dependent on its unique penetrating ability to everywhere of the cells to regulate mitochondrial homeostasis by activating the Keap1-Nrf2 phase II antioxidant system, rather than its direct free radical scavenging activity. In this review, we summarize the protective effects and focus on the mechanism of H2 as a mitochondria-targeting nutrient by activating the Keap1-Nrf2 system in different disease models, and wish to provide a more rational theoretical support for the medical applications of hydrogen.

Background: Endothelial dysfunction (ED) is a marker of vascular damage and the precursor of cardiovascular diseases such as hypertension, which involve inflammation and organ damage. Nitric oxide (NO) produced by eNOS, which is induced by pAKT, plays a crucial role in the function of a healthy endothelium. Methods: A combination of the subfractions SF1 and SF3 (C4) of the aqueous fraction from Cucumis sativus (Cs-Aq) was evaluated to control endothelial dysfunction in vivo, and on HMEC-1 cells to assess the involvement of pAkt in vitro. C57BL/6J mice were daily injected with Ang-II for 10 weeks. Once hypertension was established, Cs-AqC4 or losartan were orally administered along with Ang-II for another 10 weeks. Blood pressure (BP) was measured at weeks 0, 5, 10, 15, and 20. Serum creatinine was quantified; the inflammatory status was evaluated in kidney, and tissue damage and vascular remodeling were studied in liver and aorta. Cs-AqC4 was also evaluated in vitro on HMEC-1 cells stimulated by angiotensin II (Ang-II) to assess the involvement of Akt phosphorylation. Results: Cs-AqC4 decreased systolic and diastolic BP, reversed vascular remodeling, decreased IL-1β and TGF-β and increased IL-10 and decreased kidney and liver damage. In HMEC-1 cells, AKT phosphorylation and NO production were increased. Conclusions: Cs-AqC4 controlled inflammation and vascular remodeling, resulting in BP regulation; it also improved tissue damage associated with ED, probably via Akt activation.

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

Mangroves offer vital ecological advantages including air and water filtration, coastal and estuarine habitat provision, sediment stabilization, and wave energy absorption. Their intricate root systems play a key role in safeguarding shorelines from tsunamis and erosive storms by dissipating wave energy. Moreover, mangroves shield against boat wakes and wind-waves, bolstering shoreline defense. Wave dissipation is a function of forest width, tree diameter, and forest density. Restoration efforts of juvenile mangroves in Florida’s Indian River Lagoon (IRL) aim to reduce wave energy in areas vulnerable to erosion. Physical model testing of wave dissipation through mangroves is limited due to the complexity in representing the mangrove structure, where prop roots are non-uniform in both diameter and location. Previous studies have quantified wave dissipating effects through use of scaled and parameterized mangrove structures. This study measures the dissipation effects of live mangroves in a wave flume, forced by conditions representative of the IRL. These measurements are used to validate a parameterized dowel model. Error between wave attenuation factors for the live mangrove and dowel system was on average 2.5%. Validation of the modularized dowel system allowed for further parameterized testing to understand forest structure effects, such as sediment stabilization and wave attenuation.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

Reactive oxygen species (ROS) are a major risk factor for the development of oxidation and inflammation. Ryegrass (pasture), a natural dietary fiber source, acts as an antioxidant with well-known anti-inflammatory properties. The current study aimed to examine the alkaline phosphatase (ALP)-dependent Kelch-like-ECH-associated protein 1- Nuclear factor erythroid 2-related factor 2 (Keap1-Nrf2) signaling pathway that facilitates the anti-oxidative and anti-inflammatory properties of pasture and its protective effects on ileal permeability, systemic inflammation, nutrient absorption, liver dysfunction, growth performance, intestinal organ development, and metabolic syndrome in commercial diet-challenged geese. The lipopolysaccharides (LPS), ALP, ROS, and tight junction proteins were determined from the ileum tissues, and the antioxidant enzymes, immunoglobulins, and metabolic syndrome were determined from liver tissues via Enzyme-linked immunosorbent assay (ELISA) kits. While the Nrf2 and LPS/ROS/Keap1-induced inflammatory cytokines were determined by the quantitative reverse transcription polymerase chain reaction (RT-qPCR) method. The intestinal morphology was examined by Hematoxylin and Eosin (H&E) staining to determine nutrient absorption in ileal tissues. Pasture-dependent ALP activity significantly ameliorated commercial diet-induced LPS and ROS-facilitated ileal barrier dysfunction and systemic inflammation. The pasture supplementation induced nutrient absorption by influencing intestinal organ development. Our biochemical assays showed that the activation of Nrf2 significantly increased antioxidant enzymes and immunoglobulins, and decreased Keap1 and malondialdehyde (MDA) concentrations in the liver tissues after pasture supplementation. The correlation analysis of ALP, LPS, ROS, and Keap1-Nrf2 pathway-dependent antioxidant enzymes with other host markers showed that pasture supplementation induced intestinal barrier function via reducing LPS/ROS-induced intestinal permeability and systemic inflammation in the ileum and liver tissues. Pasture intake might attenuate LPS/ROS-induced gut permeability, systemic inflammation, and metabolic syndrome and augment gut barrier functions, nutrient absorption, immunity, and growth performance, possibly by its Keap1-Nrf2 pathway-dependent antioxidant properties.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

Nanoporous materials, such as Metal-Organic Frameworks (MOFs), are renowned for their high selectivity as gas adsorbents due to their specific surface area, nanoporosity, and active surface chemistry. A significant challenge for their widespread application is their behavior and reduced gas uptake in wet conditions, attributed to competitive adsorption between gas and water. The current understanding of gas adsorption in wet materials is constrained by studies that utilize only small amounts of powdered porous materials (in the milligram range) within very small reactors (1-5 mL). This leaves a significant gap in knowledge about gas adsorption behaviors in larger reactors and when MOF sample sizes are increased (to the gram scale) for scaling up the process. Additionally, there is a notable dearth of experimental research in situations where MOFs are heavily saturated with water. To address these gaps, this study measures CH4 adsorption in MOFs under conditions of high moisture content, using larger samples of MOFs (in grams) and a large volume reactor. We selected commercially available MOFs, including HKUST-1, ZIF-8, MOF-303, and activated carbon. A high-pressure isotherms (at T = 274.15 K) using volumetric approach were measured to qualitatively compare the moles of gas adsorbed under both dry and wet conditions across different MOFs and weights. Experimental results show that the presence of water led to a decrease in total CH4 mmol adsorption in MOFs, with a more significant decrease observed in hydrophilic MOFs compared to hydrophobic ones. For hydrophilic MOFs, presence of crossover isotherms at crossover pressure provided evidence of water's conversion to hydrate and its positive role in enhancing total gas uptake, which varied among different hydrophilic MOFs. Oversaturated MOFs showed a larger deviation between dry and wet cases at higher pressures. The high-pressure isotherm data confirm the positive role of hydrophilic MOFs in the conversion of water to hydrate in oversaturated MOFs when MOFs sample size is large.

In recent years, cerium dioxide (CeO2) has attracted considerable attention owing to its remarkable performance in various applications, including photocatalysis, fuel cells, and catalysis. This study explores the effect of nickel (Ni) doping on the structural, thermal, and chemical properties of CeO2 nanorods, particularly focusing on oxygen vacancy-related phenomena. Utilizing X-ray powder diffraction (XRD), alterations in crystal structure and peak shifts were observed, indicating successful Ni doping and the formation of Ni2O3 at higher doping levels, likely due to non-equilibrium reactions. Thermal gravimetric analysis (TGA) revealed changes in oxygen release mechanisms, with increasing Ni doping resulting in the release of lattice oxygen at lower temperatures. Raman spectroscopy corroborated these findings by identifying characteristic peaks associated with oxygen vacancies, facilitating the assessment of Ni doping levels. Overall, this study underscores the substantial impact of Ni doping on CeO2 nanorods, shedding light on tailored catalytic applications through modulation of oxygen vacancies while preserving the nanorod morphology.

Sesame seeds are abundant in sesamin, which exerts health-promoting effects such as extending the lifespan of adult Drosophila and suppression of oxidative stress accumulation by activating the Nrf2 transcription factor. Here, we investigated whether sesamin activated Nrf2 in larval tissues and induced the expression of Nrf2 target genes. In sesamin-fed larvae, Nrf2 was activated in the central nervous system (CNS), gut, and salivary glands. However, ectopic expression of Keap1 (Nrf2 inhibitor) in glial cells inhibited sesamin-induced Nrf2 activation in all tissues except in the neurons, indicating that sesamin activates Nrf2 in glia. We labeled the astrocytes as well as cortex and surface glia with red fluorescence to identify these glial cell types in which Nrf2 was activated; we observed their activation in both cell types. These data suggest that sesamin may stimulate the expression of antioxidative genes in glial cells. Among the 17 candidate Nrf2 targets, the mRNA levels of Cyp6a2 and Cyp6g1 in cytochrome P450 were elevated in the CNS, gut, and salivary glands of sesamin-fed larvae. However, this did not lead to resistance against imidacloprid, which is detoxified by these enzymes. Our results suggest that sesamin may exert similar health-promoting effects on the human CNS and digestive tissues.

Nasopharyngeal carcinoma (NPC) has not been thoroughly studied, and the pathogenesis of NPC is unclear. Scientists have neither discovered effective therapies nor achieved a desirable prognosis. Some studies have found that the regulation of intra- and extracellular ion channels hinges directly on cell apoptosis, and treatment with Gambogenic acid (GNA) brings changes to the volume-sensitive outwardly rectifying chloride (VSOR Cl-) current of CNE-2Z cells recorded by the patch clamp method. Nevertheless, rarely have any researchers probed into the relevance between this variation and the anti-tumor mechanism of GNA. This paper is suggested that GNA activates the VSOR Cl- current on the CNE-2Z cell membrane, and the activation of VSOR Cl- currents by GNA in CNE-2Z cells is blocked by the chloride channel blockers DIDS and DCPIB. GNA induces the down-regulation of GRP78 and up-regulation of ATF4 as well as chop proteins, which is evidence for the induction of CNE-2Z cell apoptosis, and this correlates with ER stress. GNA can activate the VSOR Cl- channel and lead to the occurrence of ER stress, thus inducing the apoptosis of CNE-2Z cells and inhibiting the proliferation of CNE-2Z cells.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Every subset S of a Cartesian spaces Rd, endowed with differen- tial structure C∞(S) generated by restrictions to S of functions in C∞(Rd), has a canonical partition M(S) by manifolds, which are or- bits of the family X(S) of all derivations of C∞(S) that generate local one-parameter groups of local diffeomorphisms of S. This partition satisfies the frontier condition, Whitney’s conditions A and B. If M(S) is locally finite, then it satisfies all definitions of stratification of S. This result extends to Hausdorff locally Euclidean differential spaces.

The Na+/K+ ATPase is a protein involved in the active transport of ions across the cellular membrane. Ouabain is a cardiotonic glycoside that, by inhibiting the Na+/K+ pump, interferes with cell processes mediated directly by the pump, but also indirectly influences other cellular processes, such as cellular cycle and proliferation, growth, cell differentiation, angiogenesis, migration, adhesion and invasion. We used the SK-BR-3 breast cancer cell line, mesenchymal stem cells (MSCs), and tumor-associated fibroblasts (TAFs) in vitro for determining the changes induced by Ouabain in concentration of 10-5 M, 10-6 M, 10-8 M, 10-9 M on these cellular types, employing specific methods: SEM for morphological evaluation; immunocytochemistry, flowcytometry to assess immunophenotypical markers expression, cell cycle and Annexin V/PI assay for cellular proliferation and viability testing; flowchamber assay to evaluate functional adhesion behavior; RT-PCR for Na+/K+ ATPase subunits molecular expression. Being indicative of the pro-apoptotic and inhibitory effect of Ouabain on tumor invasion and metastasis, the results support the addition of Ouabain to the oncological therapeutic arsenal, trailing the “repurposing drugs” approach.

Keywords: Innovation ecosystems, Economic sustainability, Hydrocarbon-based economies, Economic diversification, Qualitative approach

The β-thalassemias are hereditary monogenic diseases characterized by low or absent production of adult hemoglobin and excess in the content of α-globin. This excess is cytotoxic for the erythroid cells and responsible of the β-thalassemia associated ineffective erythropoiesis. Therefore, the decrease of α-globin excess is a relevant clinical effect for these patients and can be obtained by induction of fetal hemoglobin, by autophagy, or both. The in vivo effects of sirolimus (rapamycin) and analogues on induction of fetal hemoglobin (HbF) is of key importance for therapeutic protocols in a variety of hemoglobinopathies, including β-thalassemia. In this research communication, we report data showing that decrease of autophagy-associated p62 protein, increased expression of ULK-1 and reduction of the excess of α-globin is operating in erythroid precursors (ErPCs) stimulated in vitro with low dosages of sirolimus. In addition, increased ULK-1 mRNA content and decrease of α-globin content were found in ErPCs isolated from β-thalassemia patients recruited for the NCT03877809 clinical trial and treated with 0.5-2 mg/day sirolimus. Our data support the concept that autophagy, ULK1 expression and α-globin chain reduction should be considered important endpoints in sirolimus-based clinical trials for β-thalassemia.

NK population is characterized by distinct NK cell subsets which respond differently to the various activating stimuli. For this reason, the determination of the optimal cytotoxic activation of the different NK subsets can be a crucial aspect to be exploited to counter cancer cells in oncologic patients. To evaluate how the triggering of different combination of activating receptors can affect the cytotoxic responses of different NK cell subsets, we developed a microbead-based degranulation assay. By using this new assay, we were able to detect CD107a+ degranulating NK cells even within the less cytotoxic subsets (i.e. resting CD56bright and unlicensed CD56dim NK cells), thus demonstrating its high sensitivity. Interestingly, signals delivered by the co-engagement of NKp46 with 2B4, but not with CD2 or DNAM-1, strongly cooperate to enhance degranulation on both licensed and unlicensed CD56dim NK cells. Of note, 2B4 is known to bind CD48 hematopoietic antigen, therefore this observation may provide the rationale why CD56dim subset expansion correlates with successful hematopoietic stem cell transplantation mediated by alloreactive NK cells against host T, DC and leukemic cells, while sparing host non-hematopoietic tissues and graft versus host disease. The assay further confirms that activation of LFA-1 on NK cells leads to their granule polarization, even if, in some cases, this also takes to an inhibition of NK degranulation, suggesting that LFA-1 engagement by ICAMs on target cells may differently affect NK cell response. Finally, we observed that NK cells undergo a time-dependent spontaneous (cytokine-independent) activation after blood withdrawal, an aspect that may strongly bias the evaluation of the resting NK cell response. Altogether our data may pave the way to develop new NK activation and expansion strategies that target the highly cytotoxic CD56dim NK cells and can be feasible and useful for cancer and viral infection treatment.

Bangladesh's railway system mostly uses typical manual railway crossing technique or boom gates through its 2,955.53 km rail route all over the country. The accidents are frequently happening in the railway crossings due to not having obstacle detectable and quickly operating gate systems, and also for fewer safety measures in the railway crossing. Currently, there are very few automatic railway crossing systems (without obstacle detectors) available, however, all of them are dependent on the national power grid without a backup plan for any emergency cases. Bangladesh is still running a bit behind in the power generation of its consumption, hence it is not possible to have a continuous power supply at all times all over the countryside. We aim to design and develop a smart railway crossing system with an obstacle detector to prevent common types of accidents in the railway crossing points. We design to use two infrared (IR) sensors to operate the railway crossing systems which will be controlled by the Arduino Uno. This newly designed level crossing system will be run with the help of sustainable renewable energy which is cost-effective, eco-friendly, and apply under the national green energy policy towards achieving sustainable development in Bangladesh as a part of the global sustainable goal to face climate change challenges. We have summarized the simulated results of several renewable energy sources including a hybrid system and optimized the Levelized Cost of Energy (LCOE), and the payback periods.

Chalcones are a class of flavonoids possessing a variety of biological activities, including antimicrobial and antioxidant effects. Therefore, chalcones and their derivatives have potential use in the control of postharvest diseases. In this work, the effects of 2ʹ,4ʹ-dichloro-chalcone on the in vitro growth and in vivo pathogenicity of F. tricinctum and T. roseum were investigated. The results showed that 100 µM of 2ʹ,4ʹ-dichloro-chalcone strongly inhibited mycelial growth and conidial production of F. tricinctum (32.3%) and T. roseum (65.2%) in vitro. This treatment also significantly inhibited the expansion of potato dry rot from F. tricinctum (48.6%) and apple rot spot from T. roseum (36.2%). The incubation of F. tricinctum and T. roseum conidia with this agent for 2 h increased their cell membrane permeability by 25% and 22.5%, respectively and conidial membrane permeability by 41.7 and 65.4%, respectively. This treatment also significantly inhibited the total respiration rate and activated the cyanide-resistant respiratory pathway in both pathogens. Protein immunoblotting showed that the treatment increased alternative oxidase (AOX) levels after 4 h in F. tricinctum and T. roseum by 52.76% and 39.13%, respectively. Conclusion: 100 µM 2ʹ,4ʹ-dichloro-chalcone significantly inhibited mycelial growth and spore production in F. tricinctum and T. roseum in vitro and reduced their pathogenicity in postharvest potato and apple crops. Further analysis indicated that 2ʹ,4ʹ-dichloro-chalcone disrupted the integrity of cell membranes and the mitochondrial respiratory electron transport chain which leaded to ROS burst and oxidative stress, AOXs were induced directly or indirectly, and the cyanide resistant respiratory pathway was activated. The in vitro growth and pathogenicity of F. tricinctum and T. roseum were inhibited.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

This study aims to analyse the technical viability and economic feasibility of rainwater harvesting systems for single and multifamily residential buildings in the city of Florianópolis, Brazil. Simulations were conducted for representative buildings in the city under different water usage scenarios and system designs, in a total of 36 simulation scenarios. An economic analysis was performed for four scenarios over a twenty-year period. Both initial and operational costs were considered and net present value, internal rate of return and payback used as feasibility indicators. Almost all of the cases simulated were technically viable for the group of houses, and up to 78.9% for flats. As for the economic analysis, for houses, between 60.1% and 74.8% of the cases were economically feasible, achieving a discounted payback period ranging from 6.2 to 8.6 years. For flats, between 57.8% and 64.2% of the cases were economically feasible, achieving a discounted payback period ranging from 4.8 to 5.6 years. As the water tariff in the city underwent changes recently, the former and current tariff formats were compared. The current tariff format provides more economic benefits for saving potable water, and leads to a higher net present value and a shorter discounted payback period.

The transition to sustainable energy systems in the Middle East and North Africa (MENA) region addresses critical challenges of environmental protection, energy security, and socio-economic resilience. Using neo-institutional theory, this paper examines the intricate relationship between formal and informal institutions and their significant impact on the region’s energy transition. Despite the MENA region’s abundant renewable energy resources, numerous institutional barriers, such as governance inefficiencies, regulatory inconsistencies, and entrenched socio-cultural norms, significantly hinder this transition. Through a review of existing literature, this study presents a comprehensive analytical framework designed to overcome these barriers, with a focus on the Just and Sustainable Energy Transition model. This strategic model emphasizes equity, sustainability, and inclusive governance as pillars for reform. The study offers detailed recommendations for institutional change and underscores the importance of collaborative efforts among governments, industry stakeholders, and international partners to unlock the MENA region’s renewable energy potential, advance global sustainability goals, and ensure a more secure and resilient energy future.

Pakistan relies mostly on fossil fuel for fulfilling its energy demand which is expensive as 11 well as not friendly for the environment. The need of the hour is to shift from fossil fuels to renew-12 able energy resources like geothermal, wind, solar etc. to cater for global warming issues. Pakistan 13 has a lot of potential geothermal sites because of several fault lines and hot springs. A sound 14 knowledge of ground temperature is essential to use geothermal energy, which is obtained by drill-15 ing boreholes and putting sensors making it an expensive procedure. Thus, to avoid huge cost for 16 drilling bore holes, particularly for ground temperature analysis, a numerical approach has been 17 considered for determining ground temperature. Furthermore, correlation charts between air and 18 ground temperatures have been developed as there were no proper studies on the ground temper-19 ature of Pakistan. Then, with the help of a boreholes drilled in National University of Sciences and 20 Technology Islamabad Pakistan, the actual ground and numerically calculated temperatures have 21 been compared which shows an error margin in the range between 0.27% for higher depths to 7.3% 22 near surface. Thus, it is shown that the proposed method is easy to implement and better than large 23 scale testing methods for the depths at which geothermal energy is extracted.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

Significant efforts are being made across academia and industry to better characterize lithium-ion battery cells as reliance on the technology for applications ranging from green energy storage to electric mobility increases. The measurement of short-term and long-term volume expansion in lithium-ion battery cells is relevant for several reasons. For instance, it provides information about the quality and homogeneity of battery cells during charge and discharge cycles, as well as aging over it’s lifetime. The expansion measurements are useful for the evaluation of new materials and the improvement of end-of-line quality tests during cell production. These measurements may also indicate the safety of battery cells by aiding in predicting state of charge and state of health over the lifetime of the cell. Expansion measurements can also assess inhomogeneities on the electrodes and defects such as gas accumulation and lithium plating. In this review, we first establish the known mechanisms through which short term and long term volume expansion in lithium-ion battery cells occurs. We then explore the current state-of-the-art for both contact and non-contact measurements of volume expansion. This review compiles existing literature to outline the various options available to researchers aiming to make ex situ volume expansion measurements by doing post mortem analyses on individual components and in operando measurements on entire battery cells. Finally, we discuss the different considerations when selecting an appropriate measurement technique. The selection of the optimal method for measuring battery cell expansion depends on the objective of the characterization, duration, required resolution, and repeatability of results. Costs and required space for the measurement equipment are also considered.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

Alginate-silver nanocomposites in the form of spherical beads and films were prepared using a green approach by using the aqueous extract of Ajwa dates seeds. The nanocomposites were fabricated by in situ reduction and gelation method by ionotropic crosslinking using calcium ions in solution. The rich phytochemicals of the dates seeds extract played a dual role as reducing and stabilizing agent in the synthesis of silver nanoparticles. The formation of silver nanoparticles was studied using UV-Vis absorption spectroscopy and a distinct surface plasmon resonance (SPR) peak at 421 nm characteristic of silver nanoparticles confirmed the green synthesis of silver nanoparticles. The morphology of the nanocomposite beads and film was compact with even distribution of silver nanoclusters. The catalytic property of the nanocomposite beads was evaluated for the degradation of 2-nitrophenol in the presence of sodium borohydride. The degradation followed pseudo-first order kinetics with a rate constant of 1.40 ´ 10^-3 s^-1 at 23 °C with an activation energy of 18.45 kJ mol^-1. The thermodynamic parameters such as changes in enthalpy and entropy were evaluated to be 15.22 kJ mol^-1 and -197.50 J mol^-1 K^-1, respectively. The nanocomposite exhibited properties against three clinically important pathogens (Gram-positive and Gram-negative bacteria)

The process involved in preparing driving simulator tests is a labor intensive one, and the nature of this complexity depends on the sophistication of the tests to be carried out, as well as the number of participants. Which has an impact on the duration of the research itself. The very solution of using driving simulators is a research tool that has been in use for many years and with great success. They are used in a very wide range of areas of human functioning. They replicate in a very realistic way the conditions that can occur in the external environment, offer the possibility of repetition of particular conditions and insight into certain behaviors that could be very difficult to initiate in real life. This article also describes the dis- ease of using simulators to conduct research activities, along with the workflow from assumptions to finalizing the research. An algorithm is also presented for the study of individual participants, with examples for separate research scenarios concerning driver behavior in the vicinity of pedestrian crossings.

Abstract: Wildfires in forest ecosystems exert substantial ecological, economic, and social impacts. The effectiveness of fire management hinges on precise pre‐fire risk assessments to inform mitigation efforts. This study aims to investigate the relationship between predictions from pre‐fire risk assessments and outcomes observed through post‐fire burn severity analyses. In this study, forest fire risk was assessed with the Fuzzy Analytical Hierarchy Process, in which fire behavior factors were used as input. The degree of burn was determined using the Random Forest method using 11519 training points and 400 test points on Sentinel‐2 satellite images in three different classes. According to the results obtained from 266 selected test points located within the forest boundaries, all primary factors showed an increased effect in areas with high burn severity. Climate, in particular, emerged as the most influential factor, accounting for 52% of the overall impact. However, in cases of high fire severity, climate proved to be the most effective risk factor, ac‐counting for 67%. It followed by topography with 50% accuracy at high fire intensity. In the risk assessment is based on the FAHP method, climate was assigned the highest weight value among other factors with 32.2%. Topography emerged as the second most effective risk factor with 27 %. To evaluate the results more comprehensively both visually and statistically, two regions with different stand canopy characteristics were selected within the study area. While high burn severity had the highest accuracy in Case 1 area, moderate burn severity had the highest in Case 2 area. During the days when the fire continued, the direction of spread was obtained from MODIS images. In this way, the fire severity depending on the direction of fire progression was also interpreted. Through an analysis of various case studies and existing literature, the research underscores both the strengths and limitations inherent in predicting forest fire behavior‐based pre‐fire risk assessments. Furthermore, it emphasizes the necessity of continuous improvement to increase the success of forest fire management.

Transitioning to clean cooking fuels is not only part of achieving SDG7, but also makes a significant contribution to mitigating climate change by reducing carbon emissions. The paper contradicts the conventional wisdom that electricity is too expensive to cook with. The paper explores the energy required to cook dishes using different technologies and fuels by analysing data from Cooking Diaries and Controlled Cooking tests conducted under the MECS programme. Electric pressure cookers (EPCs) use least energy when compared with electric hotplates, and a detailed description of how the EPC works explains why this should be. The paper draws out distinctions between African and Asian dishes, notably the impact of energy intensive dishes prepared mostly in Africa. Standard efficiency based approaches to comparing the performance of stoves are not appropriate to modern electric cooking devices so an alternative approach based on specific energy consumptions is proposed e.g. charcoal stoves use 15 times as much energy as EPCs to cook African dishes. Energy ratios provide a basis for estimating carbon emission reductions associated with transitioning to modern cooking fuels. Historical costs show that the cost of cooking with an EPC can be only 20% of the cost of cooking with charcoal, which highlights the potential for modern, energy efficient electric cooking devices to defy the conventional wisdom of the energy ladder.

Sustainability of current energy policies and known mid-term policies are analised in their multiple facets. First an overview is given about the trend of global energy demand and energy production, analysing the share of energy sources and the geographic distribution of demand, on the basis of statistics and projections published by major agencies. The issue of sustainability of the energy cycle is finally addressed, with specific reference to systems with high share of renewable energy and storage capability, highlighting some promising energy sources and storage approaches.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

This paper explores the views of a group of young men aged 16–18, studying towards a Level 1 diploma in music in the North East area of England. It uses the conceptualization of “social haunting” to focus our discussions about how Level 1 learners articulated their experiences in the context of their learning journeys and perceived marginalization. The research took place at a large Further Education (FE) college and included a series of five “research encounters” with the group of Level 1 learners. These encounters included a range of activities, resulting in a variety of data being collected, including several activity worksheets, structured and unstructured focus group interviews, and questionnaires. This paper focusses on the outcomes of a single research activity that focused on exploring the topic of marginalization. We present a discussion on social haunting as one of the emerging findings from this research encounter, outlining how the reality of the social and cultural legacy of the UK’s industrial past can shape today’s youth and their futures. We will talk about the young men’s views of marginalization, their school-to-work transitions, the formation of masculinity in post-industrial communities and the role of Further Education in it. The paper concludes by discussing some insights for practice and future research.

We will apply Pascal’s hydrostatic pressure law to black holes and also to the Hubble sphere. Haug has recently demonstrated how hydrostatic pressure in water can be utilized to determine the Planck length. One can conceptualize the energy in the Hubble sphere as a type of superfluid, and if this is correct, then Blaise Pascal’s hydrostatic pressure formula may also be applicable to such a superfluid, even within the Hubble sphere. By employing the same method on the Hubble sphere and considering it as a Schwarzschild black hole with the critical Friedmann mass, we can estimate the Planck length based on its hypothetical hydrostatic pressure.

In the field of delta-sigma modulators, reducing system power consumption without sacrificing accuracy has become a challenge. The summing circuit, as the main part of the cascade-of-integrator-in-feedforward delta-sigma modulator, consumes a significant amount of power in active summing. On the other hand, passive summing circuits have low power consumption but can cause attenuation in the summing results. This article proposes a low-power multi-bit delta-sigma modulator based on passive and attenuationless summation scheme. The summation circuit achieves multiplication of the voltage signal carried on the summation capacitor through bidirectional sampling technique, compensating for the inherent attenuation caused by passive summation, thus eliminating the need for active OTA to achieve perfect summation. A 2-order delta-sigma modulator based on 4-bit 1-order passive noise-shaping (NS) SAR quantizer is designed to verify the scheme. By combining a passive NS SAR as the 4-bit quantizer and the third-stage integrator of the system, and incorporating an energy-efficient cascode floating inverter amplifier (FIA) structure as the core active OTA, these elements have significantly enhanced the energy-efficiency of the modulator. Simulation results show that at a supply voltage of 1.2 V and a bandwidth of 20 kHz, the SNDR reaches 102.62 dB, power consumption is only 148.32 μW, and Schreier figure-of-merit (FoM) of SNDR is 183.92 dB.

Dirac's Large Number Hypothesis (LNH), proposed in 1937, has captivated the scientific community with its exploration of profound correlations between cosmic and atomic scales. This hypothesis delves into the intricate interplay between the infinitesimally small and the vastly large, offering potential insights into the fundamental nature of the universe. As we continue to uncover the mysteries of the cosmos, the LNH oscillates on the precipice of scientific acceptance—neither fully validated nor entirely dismissed. In this review paper, we embark on a comprehensive journey through Dirac's LNH, shedding light on its theoretical underpinnings, its implications for universe models, and its resonance with the Anthropic Principle. We delve into the possibilities of variable gravitational constants and continuous mass creation, inviting further exploration into the intricacies of our cosmic symphony. By embracing the ongoing quest for understanding, we endeavor to unravel the profound harmonies that connect the infinitesimal with the infinite, contributing to the symphony of knowledge in theoretical physics and cosmology.

Over the last few decades, advancements in astrophysics have been closely linked to the development of powerful machine-learning models that can accurately classify celestial bodies. At the same time, however, many astronomical datasets are filled with new features collected by increasingly powerful telescopes. These features can cause overfitting, clouding predictive abilities, and dampening the ability of many models to classify images. Therefore, motivation to design more efficient models has skyrocketed—aiming to optimize for lower run times and high accuracies, even with fewer provided features. In our project, we seek to optimize a convolutional neural network model using a technique known as wavelet analysis. This technique allows us to pick the key features of an astronomical image and accentuate niche details, saving time and boosting accuracy. We applied it to the MiraBest Dataset, a dataset compiled from the FIRST sky survey using a virtual telescope. In the end, after training our neural network on the original images and the five filters (approximation, horizontal, vertical, diagonal, and combined), we found that with fewer features and less overfitting, the vertical Daubechies-family wavelet filter outperformed the original runs with the unaltered images by over 10%. Our findings suggest that wavelet analysis can help harvest the most valuable features in images of celestial bodies–leading to enhanced predictions in astronomical applications and perhaps bolstering modern astrophysical theory.

Prostate cancer is the second most frequent malignancy (after lung cancer) in men worldwide. Prostate tissue biopsies are usually graded using scores according to the Gleason grading system. This Gleason score is the most popular prognostic marker that reveals the potential aggressiveness of the disease. However, inter-observer variability in rating by human assessors is a major limiting factor. Such variability could lead to missing a severe case or suggesting unnecessary treatments. This study explores the discriminative ability of artificial intelligence (deep learning models) for Gleason score assessment. The study was designed to use whole-slide images of digitized H&E-stained biopsies of prostate tissues to automate the grading process and provide a remotely accessible clinical decision support system. Custom convolutional neural network architectures were trained on 10,616 images of prostate tissues. Gaussian filters were applied to pre-process the images and improve model performance. Transfer learning was applied to train eight machine learning architectures namely: Xception, VGG16 & 19, ResNet101, MobileNet, DenseNet121, EfficientNetB5 & B7. Efficient NetB7 had the best performance 85.2% compared with ground-truth classification by experts. Performance improves as more data is available. The model was deployed and hosted as a web application API on Google cloud service to ensure remote access. Tissue biopsy images can be uploaded and the corresponding Gleason score recovered immediately. This system reduces diagnostics turnaround time, increase throughput, and compensate for limited skills, especially in low resource settings.

To accurately identify high-quality functional wood with superior mechanical properties and enhance its durability, it is imperative to understand the relationships between the physical and mechanical attributes of diverse wood types. Presently, there exist issues related to accuracy, efficiency, and differentiation in studying these performance correlations. The Liang Kleeman (L-K) information flow theory, a causative analytical approach rooted in fundamental physics principles, offers swift computational capabilities. Furthermore, the coefficient of variation in L-K information flow quantitatively gauges the intensity of causal effects. Therefore, this article adopts a causal artificial intelligence perspective and introduces a wood performance analysis method based on L-K information flow.This study focuses on four Chinese fir varieties, including fast-growing Chinese fir (YKS), red heart Chinese fir (CSH, XXH), and iron heart Chinese fir (XXT). By computing and comparing variation coefficients of L-K information flow for various physical properties and their impact on mechanical properties, causal relationships between these properties are elucidated. These findings are then applied to predict wood mechanical properties, achieving a remarkable maximum accuracy of 90%.In the future, these findings will prove invaluable for the selection of high-quality wood and for improving the manufacturing process to prolong the service life of functionalized wood.

Since the creation of the first parallel electrical power systems around the world, the rotor angle stability of synchronously operating generators has been one of the most crucial and challenging problems. In modern electricity networks, involving Kazakhstani, where the renewable energy technologies are rapidly penetrating, and the issue of stability takes on even greater importance due to the technical shortcomings of inverter-based generation. In this framework, an analysis of rotor angle transient stability was carried out when replacing existing synchronous generators with doubly fed induction generators under a certain pre-emergency mode. A critical proportion of active power generation by DFIG units was identified at which transient stability can still be maintained due to the sufficient stored kinetic energy of the synchronous machines remaining in operation. In addition, 2 simple solutions were investigated to improve transient stability, such as an increased time of the automatic reclosure operation and the use of special load shedding automation. For the analysis, a real power system of Mangystau region in Kazakhstan was considered, and the PowerWorld software was used.

Information and communication technologies (ICT) are increasingly permeating our daily life and we ever more commit our data to the cloud. Events like the COVID-19 pandemic put an exceptional burden upon ICT infrastructures. This involves increasing implementation and use of data centers, which increased energy use and environmental impact. The scope of this work is to take stock on data center impact, opportunities, and assessment. First, we estimate impact entity. Then, we review strategies for efficiency and energy conservation in data centers. Energy use pertain to power distribution, IT-equipment, and non-IT equipment (e.g. cooling): Existing and prospected strategies and initiatives in these sectors are identified. Among key elements are innovative cooling techniques, natural resources, automation, low-power electronics, and equipment with extended thermal limits. Research perspectives are identified and estimates of improvement opportunities are presented. Finally, we present an overview on existing metrics, regulatory framework, and bodies concerned.

A series of waterborne polyurethane (WBPU)/modified lignin amine (MLA) adhesives was prepared using modified lignin amine (MLA) as a chain extender by a prepolymer mixing process. A successful Mannich reaction was achieved during the synthesis of MLA by reacting lignin with bis(3-aminopropyl)amine. Higher tensile strength, Young’s modulus and thermal stability were recorded for WBPU/MLA adhesives with higher MLA contents. The WBPU/MLA adhesive materials were used to coat PVC substrates. The adhesive strength increased with increasing MLA content. More importantly, the MLA also enhanced the WBPU/MLA coating in terms of adhesive strength at moderately high temperatures as well as under natural weather exposed conditions. The adhesive strength was essentially unaffected with 6.48 mole% MLA in the WBPU/MLA coating after exposure to natural weather conditions for 180 days.

This paper investigates the theoretical foundation for developing renewable geothermal resources locally. For this reason, we pay attention to the role of communities in geothermal development. This study presents arguments for a framework that approaches the geothermal resources as an endogenous factor of community development. To analyse it, we create a model that explains the local economic characters of the geothermal exploitation beyond its geological conditions. It aims to conceptualise a community based geothermal development standard referring to the endogeneity principle. Geothermal energy is given attention since the characteristics of this resource determine its use locally. We argue that the role of communities in geothermal exploitation is pivotal in the process of green growth for further expansion of geothermal energy use.

In this work, we report the electric energy storage properties of (1-x)Bi0.5(Na0.8K0.2)0.5TiO3-xBi0.2Sr0.7TiO3 (BNKT-BST; x = 0.15-0.50) relaxor ferroelectric ceramics enhanced via a domain engineering method. A rhombohedral–tetragonal phase, the formation of highly dynamic PNRs, and a dense microstructure are confirmed from XRD, Raman vibrational spectra, and microscopic investigations. The relative dielectric permittivity (2664 at 1 kHz) and loss factor (0.058) were gradually improved with BST (x=0.45). The incorporation of BST into BNKT can disturb the long-range ferroelectric order, lowering the dielectric maximum temperature Tm and inducing the formation of highly dynamic polar nano-regions. In addition, the Tm shifts toward high temperature with frequency and a diffuse phase transition, indicating relaxor ferroelectric characteristics of BNKT-BST ceramics, which is confirmed by the modified Curie Weiss law (γ=1.83). The rhombohedral–tetragonal phase, fine grain size, and lowered Tm with relaxor properties synergistically contribute to a high recoverable energy density Wrec of 0.81 J/cm3 and a high energy efficiency η of 86.95% at 90 kV/cm for x = 0.45.

Aim: the main aim of this study is to compare the onset of effectiveness of mental nerve block with lingual infiltration and inferior alveolar nerve block on patients visiting dental hospital for extraction of mandibular anterior teeth. Materials and methods: The study was set in a clinical setting. This was a randomized controlled double-blind cross study, where 25 subjects received two treatments at an interval of at least 1 week in a within a dental hospital.Inferior alveolar nerve block and lingual nerve block injection is given with 2mL lignocaine 2% with 1:2,00,000 epinephrine was administered for the right side. Mental nerve block along with lingual infiltration of the corresponding tooth was given with 2mL lignocaine 2% with 1:2,00,000 epinephrine was administered on the left side.Visual analogue scale (VAS) was used in this study, which consists of a scale with range of 0-10 pain severity on which 0 indicated absence of pain and 10 the worst pain possible. The patients were asked to give scores corresponding to his/her pain, after IANB, mental nerve block and lingual infiltration and these scores were recorde.Results: From the results we can see that patients gave scores between 3-4, stating that they had moderate pain during extraction after administration of IANB (54%) (graph 2) and VAS scores of 0-1 were given by patients, which is suggestive of no pain during extraction after administration of Mental nerve block and lingual nerve infiltration (62%)Conclusion: Within the limits of the study we can conclude that mental nerve block along with lingual infiltration is an effective way to completely and quickly anaesthetise the central incisor to the 1st premolar region.

Energy consumption modelling is of critical importance for improving energy efficiency in the drive towards sustainable manufacturing. Modern manufacturing processes and machine tools are very complex as they involve interplay of several advanced technologies. Therefore, energy modelling of modern machine tools is a complex multi-disciplinary task. This paper proposes a systematic and practical framework to choose the appropriate modelling approach for a given industrial problem. The framework was validated by applying it to diverse industrial scenarios.

This paper reports on the optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation systems for cattle farming in rural areas of Bangladesh. Bangladesh is a lower middle-income country with declining rates of poverty among its 160 million people due to persistent economic growth in conjunction with balanced agricultural improvements. Most of the rural households adopt a mixed farming system by cultivating crops and simultaneously rearing livestock. Among the animals raised, cattle are considered as the most valuable asset for the small/medium-scale farmers in terms of their meat and milk production. Currently, along with the major health issue, the COVID-19 pandemic is hindering the world’s economic growth and has thrust millions into unemployment; Bangladesh is also in this loop. However, natural disasters such as COVID-19 pandemic and floods, largely constrain rural smallholder cattle farmers from climbing out of their poverty. In particular, small and medium-scale cattle farmers face many issues that obstruct them from taking advantage of market opportunities and imposing a greater burden on their families and incomes. An appropriate measure can give a way to make those cattle farmers’ businesses both profitable and sustainable. Optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation system for cattle farming is a new and forward-looking approach for sustainable development of the livestock sector. In this study, we design and optimize a thin-film coating assisted hybrid (photovoltaic-battery-generator) power system by using the Hybrid Optimization of Multiple Energy Resources (HOMER, Version 3.14.0) simulation tool. An analysis of the results has suggested that the off-grid hybrid system is more feasible for small and medium-scale cattle farming systems with long-term sustainability to overcome the significant challenges faced by smallholder cattle farmers in Bangladesh.

This paper develops a novel energy universal service bus system (EUSBS) based on emerging energy Internet (E-net) technologies. This EUSBS is a unified identification and plug-and-play interface platform to which high penetration distributed energy and equipment (DEE), including photovoltaic (PV), fans, electric vehicle charging stations (EVCSs), energy storage equipment (ESE), and commercial and residential users (CRUs), can access in a coordinated control and optimized utilization mode. First, the functions design, overall framework and topology architecture design of the EUSBS are expounded, among which the EUSBS is mainly composed of a hardware system and a software platform. Moreover, several future application scenarios are presented. Then, the hardware part of EUSBS is designed and developed, including the framework design of this hardware subsystem, and development of the hardware equipment for PV access, fans access, EVCS access, ESE access, and CRU access. The hardware subsystem consists of smart socket, and household/floor/building concentrators. Based on this, the prototypes development of EUSBS hardware equipment is completely demonstrated. Third, the software part of the EUSBS is developed as a cloud service platform for electricity use data analysis of DEE. This software subsystem contains the power quality & energy efficiency analysis module, optimization control module, information and service module, and data monitoring and electricity behavior analysis module. Based on this design, the software interfaces are developed. Finally, an application study on energy management and optimization of a smart commercial building is conducted to evaluate the functions and practicality of this EUSBS. The EUSBS developed in this paper is able to overcome difficulties in big data collection and utilization on sides of distribution network and electricity utilization, and eventually implement a deep information-energy fusion and a friendly supply-demand interaction between the grid and users. This contribution presents a detailed and systematic development scheme of the EUSBS, and moreover, the laboratory prototypes of the hardware and software subsystems have been developed based on E-net technologies. This paper can provide some thoughts and suggestions for the research of active distribution network and comprehensive energy management and optimization in power systems, as well as references and guidance for researchers to carry out research regarding energy management, optimization and coordinated control of the smart buildings.

Introductions- Liveable housing environments face the menace of global climate change. In-frastructure (including buildings and houses) continuously experiences significant impacts ex-acerbated by natural variability in climate. The study addressed how climate change impacts the resilience of residential buildings, increased maintenance frequency, and the wellbeing and comfort of residents in UK residential buildings. Design/Methodology/Approach: This study used deductive reasoning and an empirical epis-temological methodology as a data-collecting basis to evaluate primary information obtained via a questionnaire. Regression analysis was ultimately employed to analyse the collected da-ta. Result/Discussions: The findings show a significant relationship between climate change and the wellbeing of the occupants of UK residential buildings. Also, the results show that social wellbeing is more important to the occupants than mental and physical wellbeing. It reveals that residential buildings in the UK suffer the cost of maintenance due to continuous reduc-tion in the building fabric's resilience to the impacts of climate change; for instance, a recent increase in rainfall/storms results in unprecedented flooding, which continues to damage the UK residential building fabrics.

Dark energy and dark matter are described as different manifestations of vacuum energy in a new cyclic universe framework of Extra Dimensional Symmetry (EDS) that doubles large spatial dimensions with microscopic partners. In this testable framework, vacuum energy, constrained by a Planck density constraint, exists in a gravitationally dark state where actual gravitational constant G_o = 0G. While a small repulsive component is constrained by an asymptotically evolving asymmetry to the active state where G_o = 2G, some components in the inert state are enabled to gravitationally attract by neutrino induced gravitational constant with light and shear activated heavy components. Observational and experimental tests are briefly discussed.

In 2021 an acute energy crisis inflicted severe damage on the global economy, leading to escalated prices for electricity, gas, and fuel. In order to shield individuals and businesses from the mounting energy expenses, governments have been compelled to implement policy measures, including tax reductions, price restrictions or discounts, and subsidies. This research paper examines these policy responses through the lens of energy sufficiency. Energy poverty poses a significant threat to social cohesion and support for climate-related initiatives. Therefore, it is imperative to employ compensatory measures. However, the design of such solutions must carefully consider the incentives to reduce energy consumption and associated carbon emissions. The findings of the analysis demonstrate that the escalation of energy costs holds promise for achieving energy sufficiency. Nevertheless, the government's response to the surge in energy prices and energy poverty falls short and lacks precision. Most of the policy changes primarily focus on regressive energy cost subsidies and nudging households away from fossil fuels, but they fail to generate the necessary impetus for achieving energy sufficiency, which involves the elimination of energy poverty and excessive energy consumption.

The energy efficiency of existing buildings is a crucial factor in addressing Europe’s energy con-sumption challenges, accounting for nearly 40% of the total energy usage. The ongoing energy crisis, driven by the reliance on fossil fuels and increasing prices, has underscored the urgency of adopting sustainable and energy efficient practices especially to the existing building stock. Cyprus is par-ticularly vulnerable due to its heavy dependence on imported fuels for electricity generation and faces significant challenges in transforming its existing building stock into energy-efficient and sustainable structures. Extensive focus has been made by the government on the energy-efficient retrofit of non-residential public buildings. This study examines an existing cultural hall. The case study of the Cultural Hall represents the building stock before 2010 which is lacking thermal in-sulation, double glazing and any energy efficient element. It then offers an ideal case study to ex-plore sustainable solutions which can be easily adopted from the construction industry and from the building owners. The primary objective of this research is twofold: first, to develop a comprehensive retrofit plan to transform the cultural hall into a net-zero energy building; and second, to explore how this transformation can give value back to the local community. After running two simulation scenarios and providing two energy performance certificates, one with at the existing state and one with the intended retrofit measures, it is clear that the building can be a net zero energy consump-tion building. Some interesting results derived, present also how this building can provide value back to the community i.e. through solar carports for EV charging.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.