To enable net zero sustainable thermal building energy this study develops an open-source thermal house model to couple solar photovoltaic (PV) and heat pumps (HP) for grid-connected residential housing. The calculation of both space heating and cooling thermal loads and the selection of HP is accomplished with a validated Python model for air-source heat pumps. The capacity of PV required to supply the HPs is calculated using an System Advisor Model integrated Python model. Self-sufficiency and self-consumption of PV and the energy imported/exported to the grid for a case study are provided, which shows that simulations based on the monthly load profile have a significant reduction of 43% for energy sent to/from the grid compared to the detailed hourly simulation and an increase from 30% to 60% for self-consumption and self-sufficiency. These results show the importance of more granular modeling and also indicate mismatches of PV generation and HP load based on hourly simulation datasets. The back-calculation PV sizing algorithm combined with HP and thermal loads presented in this study exhibited robust performance. The results indicate this approach can be used to accelerate the solar electrification of heating and cooling to offset the use of fossil fuels in northern climates.

The growing urgency for sustainable energy solutions necessitates a deeper understanding of the environmental impacts of renewable technologies. This article aims to synthesize and analyze Life Cycle Assessments (LCA) in this domain, providing a comprehensive perspective. We systematically categorize 2,923 articles into four communities: (1) Photovoltaic systems, (2) Wind energy systems, (3) Materials for auxiliary industry of photovoltaic and wind systems, and (4) Solar thermal systems. A comparative analysis is conducted to identify methodological consistencies and disparities across these communities. The findings reveal diverse methodological approaches and a range of environmental impacts, highlighting the complexities in assessing renewable energy systems. The article underscores the significance of material selection in photovoltaic and wind systems, providing a critical overview of the current state of LCA research in renewable energy and stressing the need for standardized methodologies. It also identifies gaps in recent research, offering insights for future studies focused on integrating environmental, economic, and social considerations in renewable energy assessments.As a case study, an LCA was used to evaluate two energy supply methods for a sensor network: one connected to the public grid and another powered by a photovoltaic panel. The off-grid system, while more environmentally friendly by reducing reliance on non-renewable energy sources, posed challenges due to the high environmental impact of battery production and disposal. Integrating environmental assessments provides a robust framework for making informed decisions on sustainable technologies. The findings are critical for projects that balance technological needs with sustainability goals.

We study in detail the influence of different chemical potentials (baryon, charged, strange, and neutrino) on how and how fast a free gas of quarks in the zero-temperature limit reaches the conformal limit. We discuss the influence of non-zero masses, the inclusion of leptons, and different constraints, such as charge neutrality, zero-net strangeness, and fixed lepton fraction. We also investigate for the first time how the symmetry energy of the system under some of these conditions approaches the conformal limit. Finally, we briefly discuss what kind of corrections are expected from perturbative QCD as one goes away from the conformal limit.

Primary ciliary dyskinesia (PCD) is caused by pathologic variants in over 50 different genes that affect the structure and function of motile cilia. Low nasal NO (nNO) is a biomarker for diagnosis in patients with features of PCD; but the reason why it is low is unclear. At the cellular level, a characteristic feature shared by most PCD patients is that antigens and other particles are not cleared from the epithelial surface. Poor antigen clearance results in pro-oxidant pathway activation and airway epithelial damage and may predispose PCD patients to DUOX1- and IL33- mediated asthma. Secondary ciliary dysfunction, such as that caused by viruses or by smoking, can also contribute to asthma development. Variants in genes underlying the function of cilia, can be associated with poor lung function, even in the absence of PCD. Single nucleotide polymorphisms in PCD – related genes can be associated with increased asthma severity. The role of cilia and antigen stasis is the pathophysiology of asthma is an important area for research, because specific airway clearance techniques and other therapeutic interventions, such as antioxidants, could be of value in preventing the development of asthma and asthma-like symptoms.

Despite its growing importance as a dry beneficiation method, there is a lack of studies exploring the fundamentals aspects of dry jigging. In this sense, this study focuses on explore some essential aspects of density-based separation in dry jigs, like pulse profile, energy consumption and, especially, stratification over time, also exploring an innovative operational strategy here called “transient pulsation”. The tests were carried out using density tracers distributed across 11 density ranges (0.4-2.4 g/cm³) and employing a base bed (gravel) to analyze their segregation in a pilot-scale dry jig. Pressure drop and active power data were acquired to measure the pulse characteristics and energy consumption. The findings suggest that establishing the dry jigging cycle is more complex than in hydraulic jigs due to the compressibility of air. Stationary pulsation tests revealed an unstable behavior of stratification over time, contrasting with traditional hydraulic jigs, while transient pulsation tests unveiled varied trends in separation quality. Energy consumption analysis underscored the significant role of the blower drive. These insights have the potential to inform operational enhancements in dry jigging.

The pressing threat of global warming poses significant risks to plant survival, adversely affecting their growth and agricultural productivity. It is crucial to understand how plants react to heat stress at the molecular level to develop crops that can withstand higher temperatures. In our study, we investigated the proteome dynamics of *Arabidopsis thaliana* seedlings under moderate heat stress conditions (30°C) using a combination of 15N-stable isotope labeling and the ProteinTurnover algorithm. This approach allowed us to closely examine the proteomic changes across different cellular compartments. Our findings revealed significant changes in the turnover rates of 571 proteins, with an average increase of 1.4-fold, indicating enhanced protein dynamics under heat stress. Notably, root soluble proteins showed more subtle changes, suggesting tissue-specific responses. We also detected significant turnover variations in proteins involved in redox signaling, stress response, and metabolism, highlighting the complex nature of these adaptive mechanisms. In contrast, proteins related to carbohydrate metabolism and mitochondrial ATP synthesis showed little change, underscoring their stability. This detailed analysis illuminates the proteomic adaptations of *Arabidopsis* seedlings to moderate heat stress, enhancing our understanding of plant thermal resilience and supporting efforts to develop thermotolerant crops.

Obstructive sleep apnea (OSA) is a common sleep disorder that is associated with a wide variety of health conditions, including cardiovascular, cerebrovascular, metabolic, neoplastic, and neurocognitive manifestations. OSA is mainly characterized by repeated upper airway obstructions during sleep that cause episodes of chronic intermittent hypoxia (IH), resulting in tissue hypoxia-reoxygenation. Decreased arterial oxygen pressure (PaO2) and hemoglobin saturation (SatO2) stimulate reflex responses to overcome the obstruction. The prevalence of OSA is significant worldwide, particularly in women during pregnancy, due to the physiological changes associated with this stage of life, especially in its later stages. It is associated with an increased risk of hypertension, pre-eclampsia and diabetes, among others. OSA during pregnancy can interfere with normal fetal development and is associated with growth retardation, preterm birth, or low term weight. Carotid body stimulation and hypoxia-reoxygenation episodes contribute to cardiovascular disease and oxidative stress, that can harm both, mother and the fetus, even into the adulthood. Because gestational intermittent hypoxia (GIH) is the hallmark of OSA in pregnancy, this review examines the impact of GIH on maternal, fetal, and offspring respiratory outcomes. Most adverse outcomes can be prevented by continuous positive airway pressure (CPAP) therapy and lifestyle changes if gestational OSA is detected early and treated appropriately.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

We introduce two symmetric concepts to physics: “distance” (space and time in one) and “wavematter” (electromagnetic wave packet and matter in one). We claim that physics has chosen the wrong concept of time: It is not aware that the time of a moving object flows in a direction other than my time. We provide 15 proofs for our claim by solving 15 mysteries of physics graphically! For example, we prove that length contraction and time dilation are actually geometrical effects in a 4D manifold that we call “Euclidean spacetime” (ES). We prove that the discrepancy in calculating the Hubble constant stems from a systematic error in the redshift measurement. We prove that what I deem wave, deems itself matter, which solves wave–particle duality. We even untangle quantum entanglement without the issue of non-locality. We finally understand why alternative theories of Euclidean relativity have failed: They are all based on four dimensions of space rather than distance. A huge amount of energy was injected into ES at a point that we take as origin. Ever since has this energy been moving radially away at the speed of light. We live in the 3D hypersurface of an expanding 4D hypersphere. Hyperspherical coordinates have the great advantage that they reduce all that is ever happening to just one formula. So, it is the Theory of Everything in these coordinates: “Energy is covering radial distance which, divided by Euclidean time, is equal to the speed of light.” Acceleration and force like gravitation emerge from a rotation of objects in ES and a subsequent projection to 3D space. Matching the symmetry simplifies physics.

Carbon dioxide capture and storage (CCS) is a necessary requirement for high-emitting CO2 industries to significantly reduce volumes of greenhouse gases released to the atmosphere and mitigate the climate change. Geological CO2 storage into depleted oil and gas fields is the fastest and most accessible option for CCS deployment allowing for re-purposing of existing infrastructure and utilizing the significant knowledge about the subsurface acquired during the field production operations. Location of such depleted fields in neighbourhood of high-emitting CO2 industries is additional advantage available for matured on-shore Europe fields. Considering these advantages, the oil and gas operators are now evaluating different possibilities for CO2 sequestration projects for the fields approaching end of production. This article describes an integrated approach to reservoir simulations focused on evaluating CO2 injection pilot at one of such matured fields operated by MND and located in the Czech Republic. The potential CO2 injection site in focus is a naturally fractured carbonate reservoir. This oil-bearing formation has a gas cap at the top and a limited aquifer at the bottom of the reservoir and was produced mainly by pressure depletion with quite limited pressure support from water injection. The article summarizes results of efforts taken by the multi-disciplinary team to develop and apply an integrated approach to reservoir simulation started from geological modelling of the naturally fractured reservoir and integrating results of laboratory studies and their interpretation (geomechanical and geochemistry laboratory experiments) and dynamic field data analysis (pressure transient analysis including time-lapse) into the history matching of the reservoir model and simulations of pilot CO2 injection. Attention is given to evaluating and modelling stress-sensitive fracture properties and safe injection envelope preventing induced fracturing as well as impact of potential salt precipitation in the near wellbore area. These effects are considered in the context of pilot CO2 injection and addressed in reservoir simulations of the injection scenarios. Single porosity and permeability reservoir simulations with dominating fracture flow and black-oil formulation with CO2 simulated as a solvent were used in this study and arguments for such choice of the simulation approach for the site in focus are shortly discussed. The reservoir simulations have indicated larger site injection capacity than required for the pilot injection and allowed to evaluate CO2 migration pathway within the reservoir. The application of the approach to the site in focus has also revealed large uncertainties, related to fracture description and geomechanical evaluations, resulted in an uncertain safe injection envelope. These uncertainties should be addressed in further studies in preparation to the pilot. The article concludes with an overview of the outcomes of the integrated approach and its application to the field in focus including discussion of issues and uncertainties revealed.

Here, using the theory of electrical-quantum modelling of the neutron and proton as a three-phase alternating current electrical generator, we will analyse the proton decay and the inverse neutron decay and determine the following subatomic particles, Dproton, Protoniu, Dneutron and Neutroniumd.

Preeclampsia, a hypertensive disease of pregnancy of unknown etiology, is intensely studied as a model of cardiovascular (CVD) disease not only due to multiple shared pathologic elements, but also because changes that develop over decades in CVD disease appear and resolve within days in preeclampsia. Those affected by preeclampsia and their offspring experience increased lifetime risks of CVD. At the systemic level, preeclampsia is characterized by increased cellular, membrane, and blood levels of cholesterol, however, cholesterol dependent signaling such as canonical Wnt/βcatenin, Hedgehog, and endothelial nitric oxide synthase is downregulated indicating a cholesterol deficit with upregulation of cholesterol synthesis and efflux. Hypoxia related signaling in preeclampsia also appears paradoxical with increased Hypoxia Inducible Factors (HIF) in the placenta but measurably increased oxygen in maternal blood in placental villous spaces. This review addresses the molecular mechanisms by which excessive systemic cholesterol and deficient cholesterol dependent signaling may arise from the effects of dietary lipid variance causing the cellular hypoxia which characterizes preeclampsia.

The firmware developed for the readout and trigger processing of the information emerging from BIS78-RPC Muon Spectrometer chambers in the ATLAS experiment at CERN, is presented here, together with data processing techniques, data acquisition software and tests of the readout chain system, on the road to make these chambers operational in the ATLAS experiment. This work is performed in the context of the BIS78-RPC project, which deals with the pilot deployment of a new generation of sMDT+RPC chambers in the experiment. Such chambers are planned to be fully deployed in the whole barrel inner layer of the Muon Spectrometer during the Phase-II upgrade of the ATLAS experiment. On-chamber front-ends include an amplifier, a discriminator ASIC and an LVDS transmitter. The signal is digitized by CERN HPTDC chips and then processed by an FPGA which is the heart of the readout and trigger processing, using various techniques. The work presented here is a continuation of the work presented in [1].

Our hypothesis that controlled ozone applications interfere into the redox balance of the biological organism (first published in 1998 with a preclinical trial on protecting the liver from CCl4 intoxication), has been verified over the last 2 decades in reactive oxygen species (ROS)-induced mitochondrial pathologies, such as rheumatoid arthritis, osteoarthritis, aging processes, diabetes-2 and in prevention of intoxications. Low-dose ozone acts as a redox bioregulator: The restoration of the disturbed redox balance is comprehensible in a number of preclinical and clinical studies by a remarkable increase of the antioxidant repair markers, here mainly shown as glutathione increase and a reduction in oxidative stress markers, mainly malondialdehyde. The mechanism of action is shown, relevant data are displayed, evaluated and comprehensively discussed: The repair side of the equilibrium increases by 21% up to 140% compared to the non-ozone treated groups and depending on the indication; the stress markers are simultaneously reduced, the redox system regains its balance.

Graves' disease (GD) is an autoimmune disorder in which Thyrotropin Receptor Antibodies (TRAb) continuously stimulate thyroid receptors, leading to excessive production of thyroid hormones. TRAb also affect the orbital tissues, causing Graves' ophthalmopathy. Treatment to control Graves' disease consists of antithyroid drugs, radioiodine and thyroidectomy, and through such treatments, TRAb is reduced and the disease is alleviated. The mechanism by which TRAb, which play a critical role in the pathogenesis of Graves’ disease, decreases after GD treatment is still unknown. This paper presents a theoretical mechanism of how GD patients maintain a vicious cycle and how GD treatment can reduce the TRAb levels and breaks the cycle using stress-based ideas.

Environmental factors, such as drought-stress, significantly impact maize growth and productivity worldwide. To improve yield and quality, effective strategies for early detection and mitigation of drought-stress in maize are essential. This paper presents a detailed analysis of three imaging trials conducted to detect drought-stress in maize plants using an existing, custom-developed, low cost, high throughput phenotyping platform. We propose a pipeline for early detection of water stress in maize plants using a Vision Transformer classifier and analysis of distributions of near-infrared (NIR) reflectance from the plants. We also explored suitable regions on the plant that are more sensitive to drought-stress and show that the region surrounding the youngest expanding leaf (YEL) and the stem can be used as a more consistent alternative to analysis involving just the YEL. Our results show good separation between well-watered and drought-stressed trials for two out of the three imaging trials both in terms of classification accuracy from data-driven features as well as through analysis of histograms of NIR reflectance.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

The built environment sector’s growing impact on climate change is becoming increasingly important due to its share in energy consumption and greenhouse gas emissions. Global efforts have been undertaken to design and develop residential dwellings that aim towards zero energy and carbon emission, but there remains a multitude of obstructions to efficient construction processes. This study is focused on the gaps and barriers that have emerged during the pre-construction phase of a low-environmental-impact Passive House in Fayetteville, Arkansas. The technical, management, regulatory, and supply chain obstacles to the construction of a new three-story residential Passive House are documented to engage knowledge transformation in the design and construction of sustainable buildings of interest to developers and property owners. Primary data are collected by direct observation as well as open-ended interviews and secondary data collected through a literature review to understand the barriers and gaps faced by different key actors during the pre-construction phase in different regions. This local study highlighted the lack of interest, knowledge, and experience in sustainable building design among professionals having a significant influence on the project goals and timeline and was mentioned by participants as a common barrier as well as the inconsistency and inadequacy of regulatory framework of existing building codes to implement sustainable building design. These barriers along with other identified barriers are discussed and recommendations to overcome these barriers are provided.

Outliers seriously affect the accuracy in geometric model fitting. Previous works in coping with outliers involve threshold selection and scale estimation. However most scale estimators suppose the inlier distribution as a Gaussian model, which usually poorly meets the cases in geometric model fitting. Outliers, considered as the points with big residuals to all the true models, share common items with big values in quantized residual preferences, thus making the outliers gather away from the inliers in quantized residual preference space. In this paper we make use of this outlier consensus in quantized residual preference space by extending the usage of energy minimization to combine the model error and the spatial smoothness in quantized residual preference space for outlier detection. The energy minimization based outlier detection process follows an alternate sampling and labeling framework. After the outlier detection, an ordinary energy minimization method is employed to optimize the inlier labels, which also follows the framework of alternate sampling and labeling. The experimental results in this study show that the energy minimization based outlier detection method can detect most of the outliers in the data. Furthermore, the proposed energy minimization based inlier segmentation process segments the inliers into different models quite accurately. Overall, the performance of the proposed method is better than most of the state-of-the-art methods.

Wind energy is a kind of renewable energy with great potential for development. This study mainly investigated the application of shock waves generated by high-pressure gases (wind energy) for generating energy. In this study, we designed a new supersonic shock wave generator that can be reused without disassembling and assembling bolts and developed a supersonic shock wave monitoring system. This system monitored the velocity of the generated shock waves, which was Mach 3-5, and the output pressure was more than 100 times higher than the input pressure of the shock wave generator tank.Then, we developed a power generation system driven by supersonic shock waves based on the characteristics of the new shock wave generator, which can generate high-pressure and high-speed blast waves and can be reused. The shock wave generator can repeatedly generate high-pressure waves to drive the Tesla turbine and then the magnetic energy generator for power generation. We established a complete control process for power generation driven by shock waves by controlling the valve stem. The system can detect the tank pressure, output pressure, gas flow, rotation speed, voltage, and current during the control process for the performance analysis of power generation.

In recent years, the chiral biological effects of nanomedicines have become a subject of widespread interest. The research focus has been on understanding the influence of material chirality on cellular transcription and metabolism. Stress granules are membraneless organelles formed through liquid-liquid phase separation of G3BP1 proteins and related compartments. They have been extensively studied and proven to be closely associated with cellular damage repair and metabolism. However, the role and mechanism of chiral nanomaterials in modulating stress granules remain unknown. The aim of this study was to investigate the expression and structural characteristics of stress granules under the individual influence of chiral nanomaterials and in combination with chemotherapy. To achieve this, we constructed a library of chiral ligand-modified materials and employed immunofluorescence, live-cell imaging, and fluorescence recovery after photobleaching assays. We also used proximity labeling techniques combined with proteomics analysis to identify the protein corona adsorbed on the surface of the nanomaterials and explore their relationship with nanomaterial chirality. Our results demonstrate that the assembly of stress granules is chiral-dependent and can be regulated by chiral nanomaterials. Furthermore, we achieved enhanced chemotherapy sensitivity in cancer cells and protected normal cells by exploiting the chiral-dependent modulation of material assembly in stress granules. This study provides important insights into the regulation of membraneless cellular structures based on chiral biological effects.

Healthcare personnel must face two problems of growing importance: violence in the workplace and the loss of work ability due to ageing of the workforce. Studying the relationship between these two phenomena can help to prepare effective prevention measures. In a public health company, we asked nurses to self-assess their work ability using the Work Ability Index (WAI) and we analysed the relationship between this indicator and the violence experienced in the previous and following years. 321 out of 344 nurses (99.3%) participated. In a logistic regression model, the WAI score was a significant protective factor for violence experienced in the previous year (OR=0.94 CI95%=0.90; 0.98 p<0.01) and in the following year (OR=0.88 CI95%=0.84; 0.92 p<0.01). In a hierarchical logistic regression model, social support acted as a protective factor (OR = 0.87 CI95% = 0.79; 0.95 for violence experienced in the previous year), while occupational stress was a significant determinant of the risk of aggression (OR=3.65 CI95%=1.90; 7.03 in the previous year, OR=3.54 CI95%=1.801; 6.947 in the following year). The difficulties that nurses encounter in carrying out their growing work demands in an environment that is not promptly adapted to their changing physical and mental conditions can lead to an increased risk of violence. Prevention of workplace violence should include organizational and ergonomic measures that reduce stress and increase staff support and work ability.

Sri Lanka's vulnerability to climate change-induced natural disasters, particularly floods, under-scores the urgent need for an integrated approach to disaster risk management (DRM) that ad-dresses the interconnected challenges within the water-food-land-energy nexus. The Deduru Oya basin, located in the north-western region, exemplifies this vulnerability, with its predominantly intermediate climatic zone susceptible to flooding. While the focus has traditionally been on flood risk reduction, it is imperative to recognize the broader implications of floods on water, food, land, and energy systems. This study aims to strengthen data acquisition and management efforts to better understand rainfall trends and their impact on the water-food-land-energy nexus in the Deduru Oya basin. By compiling 60 years of rainfall data and conducting time series analysis, we observed a decreasing trend in monthly rainfall, particularly during the South-West Monsoon, Second Inter Monsoon, and North-East Monsoon seasons. These findings have significant implica-tions for water availability, agricultural productivity, land use patterns, and energy generation in the basin. Moreover, the malfunction of stakeholders' responsibilities for local-level flood risk management exacerbates the challenges faced by communities living in flood-prone areas. By in-tegrating insights from this study into flood risk management strategies, stakeholders can develop holistic approaches that not only mitigate flood risk but also enhance resilience across the water-food-land-energy nexus. This interdisciplinary approach will inform policymakers, flood manag-ers, practitioners, and the community in formulating effective strategies to address the multifacet-ed challenges posed by floods in the Deduru Oya basin and beyond.

The sustainable development of an area is highly dependable on reliable electrical energy supply. Microgrids are important in integrating distributed energy resources (DERs) using power electronic converters. However, microgrid control becomes challenging with the increasing number of distributed generators and loads. With the conventional droop control method, power contributions from DER converters cannot be accurately shared due to a mismatch of line impedances. In this paper, an augmented hierarchical control mechanism is proposed to solve the issues mentioned above. This hierarchical control mechanism consists of primary and secondary controllers. The primary stage utilized the droop controller to improve optimal power flow, mainly for the resistive network. The secondary stage is based on an improved methodology to compensate for the voltage and frequency variations during small and large signal disturbances. Moreover, the modelling and analysis for PMSG-based wind energy conversion systems are also presented. The response of the primary controller for the active and reactive power sharing is investigated. The analysis emphasizes the demonstration of optimal power-sharing under normal and abnormal conditions for the considered load. Finally, the suggested robust controller's performance is evaluated in MATLAB environment and simulation results show the proposed scheme's superiority under different operating conditions.

Cement-free concrete has superior physical performance, such as strength and durability, compared to OPC concrete, however, it has the disadvantage of large shrinkage. Large shrinkage can cause cracks due to shrinkage stress in the long term. In this study, a shrinkage reducing agent (SRA) was used to reduce the shrinkage of cement-free mortar; its content was increased from 0.0 to 1.5 %. For an SRA content of 1.0 %, a calcium sulfoaluminate (CSA) expansive additive (EA) (2.5, 5.0, and 7.5%) was added. To calculate the shrinkage stress of cement-free mortar using the SRA and EA, the compressive strength, elastic modulus, and total and autogenous shrinkage were measured. The unit shrinkage stress of cement-free mortar was obtained by multiplying the elastic modulus by the length change and accumulated to obtain the shrinkage stress acting on the mortar according to the age. The shrinkage stress of cement-free mortar showed different tendencies as the age increased. At early ages, the shrinkage rate of the mortar occupied a large proportion of the shrinkage stress. In the long term, the shrinkage stress was significantly affected by the elastic modulus. As a result, SRA was found to be effective in reducing the shrinkage stress by decreasing both the elastic modulus and shrinkage. However, EA increased the shrinkage stress over the long term due to an increase in elastic modulus even though it compensated for early-ages shrinkage.

The main challenge in milk production has been to maintain a focus on efficient processes that enhance production outcomes, while aligning with animal welfare and sustainability and being valued by society. As an alternative to improve cow welfare in production and provide better handling of the waste generated by the activity, the system called compost-bedded pack barn (CBP) is an alternative that has been widely adopted in countries with temperate climates and higher milk production. This CBP has been attracting global interest, including from countries with tropical and subtropical climates, such as Brazil, where many producers have started to use it due to the response in terms of milk productivity. A CBP can be designed either in a) an open facility with natural ventilation or positive pressure ventilation system or b) totally closed facilities, equipped with negative pressure ventilation systems and permanent thermal control. The latter system is being implemented in Brazil, despite insufficient knowledge about its efficiency. The objective of this study was, through a review, to gather and describe the most recent information on the use of open and closed CBP systems for dairy cattle housing, mainly how it is applied in tropical climate regions. To achieve the proposed objective, this review study included the following topics related to CBPs: (i) implementation; (ii) bedding; (iii) general construction and architectural characteristics; iv) ambient thermal conditioning. Knowledge gaps and directions for future research are also identified.

In the face of the burgeoning electricity demands and the imperative for sustainable development amidst rapid industrialization, this study introduces a dynamic and adaptable framework suitable for policy-makers and renewable energy experts working on integrating and optimizing renewable energy solutions. While using a case study representative model for Sub-Saharan Africa (SSA) to demonstrate the challenges and opportunities present in introducing optimization methods to bridge power supply deficits and the scalability of the model to other regions, this study presents an agile multi-criteria decision tool that pivots on four key development phases, advancing upon established methodologies and pioneering refined computational techniques, to select optimal configurations from a set of Policy Decision Making Metrics (PDM-DPS). Central to this investigation lies a rigorous comparative analysis of variants of three advanced algorithmic approaches: Swarm-Based Multi-objective Particle Swarm Optimization (MOPSO), Decomposition-Based Multi-objective Evolutionary Algorithm (MOEA/D), and Evolutionary-Based Strength Pareto Evolutionary Algorithm (SPEA2). These are applied to a grid-connected hybrid system, evaluated through a comprehensive 8760-hour simulation over a 20-year planning horizon. The evaluation is further enhanced by a set of refined Algorithm Performance Evaluation Metrics (AL-PEM) tailored to the specific constraints. The findings not only underscore the robustness and consistency of the SPEA2 variant over 15 runs of 200 generations each, which ranks first on the AL-PEM scale but also validate the strategic merit of combining multiple technologies and empowering policymakers with a versatile toolkit for informed decision-making.

Stress is a natural yet potentially harmful aspect of human life, necessitating effective management, particularly during overwhelming experiences. This paper presents a scoping review of personalized stress detection models using wearable technology. Employing the PRISMA-ScR framework for rigorous methodological structuring, we systematically analyzed literature from key databases including Scopus, IEEE Xplore, and PubMed. Our focus was on biosignals, AI methodologies, datasets, wearable devices, and real-world implementation challenges. The review presents an overview of stress and its biological mechanisms, details the methodology for the literature search, and synthesizes the findings. It shows that biosignals, especially EDA and PPG, are frequently utilized for stress detection and demonstrate potential reliability in multimodal settings. Evidence for a trend towards deep learning models was found, although the limited comparison with traditional methods calls for further research. Concerns arise regarding the representativeness of datasets and practical challenges in deploying wearable technologies, which include issues related to data quality and privacy. Future research should aim to develop comprehensive datasets and explore AI techniques that are not only accurate but also computationally efficient and user-centric, thereby closing the gap between theoretical models and practical applications to improve the effectiveness of stress detection systems in real scenarios.

The Ionian Sea is a crucial intersection for various water masses in the Mediterranean. Its hydrography and dynamics play a significant role in the seawater budgets and biogeochemistry of the neighboring sub-basins. Multiple theories have been formulated to gain a better understanding of the Ionian dynamics. These theories primarily attribute the variability of the near-surface Ionian circulation to internal processes. Here, we utilize horizontal currents and temperature-salinity profiles from the Copernicus reanalysis to examine the contribution of baroclinic modes to the variability of the basin horizontal circulation. Our findings demonstrate that, although the basin vertical structure is characterized by three layers, the primary patterns of the Ionian circulation can be attributed to the first baroclinic mode. This mode, along with the barotropic mode, accounts for over 85% of the overall variability in the Ionian circulation, suggesting that only one of the three interfaces separating the different water masses in the basin is dynamically active. We estimate the depth of this interface to be about 490 m. Additionally, our analysis shows that more than 90% of the kinetic energy over the water column is localized above this interface, indicating that the deep layer of the Ionian is dynamically nearly inert.

Total ankle replacement (TAR) implants are an effective option to restore the range of motion of the ankle joint for arthritic patients. An effective tool for analyzing these implants’ mechanical performance and longevity in-silico is finite element analysis (FEA). ABAQUS FEA was used to statically analyze the von Mises stress and contact pressure on the articulating surface of the bearing component in two newly installed fixed-bearing total ankle replacement implants (the Wright Medical INBONE II and the Exactech Vantage). This ultra-high molecular weight polyethylene (UHMWPE) bearing commonly fails and is the cause for surgeon revisions. Six different FEA models for various gait percentages during stance (10%-60%) were created. They varied in magnitude of the compressive load and the ankle dorsiflexion/plantarflexion angle. The results indicated that the von Mises stress and contact pressure distributions increased as compressive load increased, and the largest magnitudes occurred at high dorsiflexion angles (15-30°). High magnitudes occurred in regions where the thickness of the bearing was the least. Additionally, high contact pressures were examined in areas near the talar component's edge or at the bearing's edges. To the author’s knowledge, this is the first study available to the research community that analyzes the Vantage implant with FEA. This study lays an essential foundation for future researchers in presenting a thorough literature review of TAR and methods for a simple FEA model setup. This study provides valuable information that can be beneficial to medical company designers and orthopedic surgeons in understanding the stress response and contact pressure of TAR implants during use.

This study aimed to evaluate a cantilever beam-type piezoelectric energy harvester operating on train-induced vibrations for powering Wireless Sensor Networks (WSNs) used in railway track monitoring systems. The harvester's behaviors under different conditions are simulated in MATLAB using the analytical model. Natural frequency, maximum deflection, and stress were calculated with greater precision using eigenfrequency and stationary analysis using COMSOL Multiphysics. At a base excitation of 2 g and a resonant frequency of 4.38 Hz, the simulated results showed that the developed energy harvester prototype could generate up to 14 V of AC output voltage and 550 mW of output power. These findings highlight the promising potential of the proposed energy harvester for transforming train mechanical energy into electrical power. This energy harvester's viability and dependability for real-world applications in monitoring railway tracks are supported by developed analytical and simulation models.

Defining integrals over volume element in curved spacetime together with the mass and energy densities within that region of spacetime is apparently equivalent to the given energy and mass of that body or particle. With this in mind equations involving energies and mass can be rewritten in terms of their densities and the integral over the volume element. The idea find its place in the Hamiltonian formulations, and can be carried over into quantum mechanical frameworks systematically accounting for the effect of spacetime volume structures and gravity on dynamics of quantum systems. This article briefly explores this concept and runs through various frameworks and equations relevant to this idea, particularly the schrodinger-Newton equation and discusses the cosmological constant as a vacuum energy density.

Stress is an inherent sensation of being unable to handle demands and occurrences. If not properly managed, stress can develop into a chronic condition, leading to the onset of additional chronic health issues like cardiovascular illnesses and diabetes. Various stress meters have been suggested in the past, along with diverse approaches for its estimate. However, in the case of more serious health issues such as hypertension and diabetes, the results can be significantly improved. This study presents the design and implementation of a distributed wearable sensor computing platform with multiple channels. The platform aims to estimate stress levels in diabetes patients by utilizing a fuzzy logic algorithm that is based on the assessment of several physiological indicators. Additionally, a mobile application was created to monitor users' stress levels and integrate data on their blood pressure and blood glucose levels. Validation experiments were performed on patients with chronic diabetes, and the initial findings are presented in the study.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

This article presents multiple novel and compelling arguments to systematically disprove two widely accepted notions: one is that entropy is a measure of disorder, and the other is Schrödinger's notion of negative entropy (negentropy). These two notions have been cited hundreds of times annually in scientific literature for decades. To mathematically describe the second law of thermodynamics, the concept of entropy was created and defined in the 1860s as heat energy divided by thermodynamic temperature, and the entropy of an object increases when it absorbs heat. This is the uncontroversial and fundamental nature of entropy, which is pivotal to current thermodynamics and from which multiple facts are deduced. These facts consistently disprove the above two notions. Some biological facts, such as the one that life orderliness is encoded and provided by inherited genes rather than entropy decline, can also disprove Schrödinger's negentropy notion. Moreover, this article further clarifies the reasoning errors of the two notions. It also shows that the tendency of many natural or social systems to become more disordered over time does not result from the second law of thermodynamics.

Low energy consumption is a significant contribution of new and retrofitted buildings that place an emphasis on energy efficiency. Although the mandatory requirements of the U-factor and R-value are described in the Vietnamese National Technical Regulation on the energy efficiency of buildings—QCVN09:2017/BXD, these values are not widely publicized, leading to designers facing difficulties when choosing suitable materials at the design stage. This study focuses on the method used to declare the heat transfer values of building materials based on the energy labeling process in order to create an energy labeling program for building materials. To accomplish this objective, criteria and labeling procedures for windows, doors, walls, and building roofs have been developed. In addition, a case study of insulation product labeling was used to evaluate the applicability of the developed labeling program in the implementation phase.

Most existing coal-fired power plants were designed for sustained operation at full load to maximize efficiency, reliability, and revenue, as well as to operate air pollution control devices at design conditions. Depending on plant type and design, these plants can adjust output within a fixed range in response to the plant operating or market conditions. The need for flexibility driven by increased penetration of variable and non-dispatchable power generation such as wind and solar is shifting the traditional mission profile of thermoelectric power plants in three ways: more frequent shutdowns when market or grid conditions warrant, more aggressive load ramp rates (rate of output change), and lower minimum sustainable load, which provides a wider operating range and helps avoid costly plant shutdowns. Recent studies have shown that flexibility of a coal-fired power plant can be improved by energy storage. The objective of this work was to analyze a set of energy storage options and determine their impact on flexibility and economics of a representative coal-fired power plant. The effect of three energy storage systems integrated with a coal power plant on plant flexibility and economics was investigated. The results obtained in this project show that Energy Storage Systems integrated with a thermal power plant improves plant flexibility and participation in the Energy and Ancillary Services markets which improves plant financial performance. The study was funded by the U.S. Department Office of Fossil Energy FE-1 under Award Number DE-FE0031903.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

Direct Energy Deposition (DED) is a versatile and efficient method in metal additive manufacturing. However, humping, caused by abnormal dynamics in the melt pool (MP), poses a significant threat to the geometric integrity of manufactured products. Current state-of-the-art (SOTA) methods primarily detect humping by analyzing late-stage spatial abnormalities, such as MP detachment. This approach is fundamentally reactive, leading to a tendency to miss early humping spatiotemporal dynamics, like cyclic elongation of the MP. This study introduces a novel, proactive indicator named VIMPS (Variability of Instantaneous MP Solidification-Front Speed), a physics-based tool designed to quantify early abnormal fluctuations in MP solidification speed. The experiments demonstrate VIMPS correlation with humping-induced geometric inaccuracies. By capturing early spatiotemporal dynamics of the MP, VIMPS reduces detection latency by 30 seconds compared to existing SOTAs that focus solely on spatial abnormalities. This significant improvement transforms detection from reactive to proactive, providing the time needed for corrective actions to enhance the overall productivity and quality of the DED process.

Transition to renewable energy has been recognized as a crucial step to addressing climate change and achieving greenhouse gas reduction targets, but it can also cause energy sprawl if not planned properly. Clean renewable energy communities (CREC) are emerging globally as an approach for decentralized energy systems and an alternative to traditional centralized energy systems. CREC aims to lower the energy carbon footprint, enhance local energy resilience, and improve the quality of life of residents. Through a comprehensive literature review, this study reviews metrics that can assess the impact of energy transition plans and support decision-making to select technologies that create efficient, reliable, and accessible energy systems. It classifies these metrics into a five-dimensional sustainability approach: environmental, technical, social, economic, political and institutional. The paper proposes a conceptual framework to guide decision-makers in recognizing the role of sustainable land development, sustainable energy planning, and resiliency as an integrated approach to energy transition planning. This framework stresses mapping the place-based potential for clean renewable energy at various scales, highlights the importance of resilience in energy planning, and addresses challenges associated with energy source selection, built environment efficiency, and energy trade. While the framework can serve as a starting point for evaluating energy transition plans, further work is needed to address the limitations of existing metrics and identify additional evaluations for energy mixed land use that are critical to managing energy sprawl on ecosystem services and other land uses.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

Abiotic stress is responsible for significant reduction in crop plant productivity worldwide. Ultraviolet (UV) radiation is a natural component of sunlight and a permanent environmental stimulus. This study investigated the distinct responses of young wheat and einkorn plants to excessive UV-B radiation (180 min at λmax 312 nm) following foliar pretreatment with 1 µM synthetic cytokinin 4PU-30. Results demonstrated that UV radiation significantly amplified hydrogen peroxide levels in both wheat and einkorn, with einkorn exhibiting more pronounced increase compared to wheat. This elevation indicated the induction of oxidative stress by UV radiation in the two genotypes. Intensified antioxidant enzyme activities and increased accumulation of typical stress markers and non-enzyme protectants were evidenced. Transcriptional activity of genes encoding key antioxidant enzymes was also investigated aiming to elucidate the genetic regulation of the antioxidant systems in both wheat and einkorn seedlings. Our results suggested a role for POX1 and POX7 genes in the UV-B tolerance of the two wheat species as well as a cytokinin stimulated UV-B stress response in einkorn mediated through upregulation of the tau subfamily gene GSTU6. Based on these findings it could be concluded that 4PU-30 had the potential of alleviating oxidative stress by attenuating the symptoms of superfluous UV-B illumination in the two examined plant species.

Previous research has proven that one of the fundamental requirements for ensuring increased profitability and economic competitiveness of offshore-based projects is co-locating different technologies within the same marine space. This paper presents a number of techno-feasibility analyses for floating offshore technologies for the Maltese Islands, located in the Central Mediterranean Sea. The first part compares the feasibility of offshore-based solar photovoltaic prices with those onshore, taking into consideration Malta’s land prices. The second part considers the use of a novel floating breakwater design that integrates energy storage. The breakwater is used to create a sheltered water area in deep waters for a multi-use marine park. Different revenue streams for the floating break water are considered, including renting the sheltered marine space out to operators of floating solar farms, aquaculture cages and vessel berthing facilities, and the provision of energy storage services. It is found that the combined income from the multiple revenue streams is still insufficient to justify the investment and that financially support from Government is essential to render the floating breakwaters viable.

The implementation of sustainable practices, such as the use of renewable sources and efficient technologies, is crucial for reducing climate change. Energy efficiency is highly important on a global scale due to its relationship with climate change, aiming to minimize environmental impact. In Spain, renewable energy policies have increased self-sufficiency and reduced the use of fossil fuels. Optimizing energy consumption in residences, buildings, and industries is essential for improving efficiency. This was taken into consideration for conducting this study, focusing on the residential sector. The desire to understand the level of energy efficiency in Extremadura drove this project, which focuses on collecting and analyzing data on a set of homes located in the au-tonomous community of Extremadura, with the purpose of evaluating their energy efficiency. To achieve this, a computer tool will be employed to provide a detailed view of the different levels of energy efficiency present in the community. In addition to data collection and analysis, research will be conducted to identify areas for improvement. This will allow proposing a series of specific measures that users can implement to optimize energy efficiency in their homes, adapting them to the particular characteristics of each residence.

Plant responses to different light and water availability are variable among species and their re-spective phenotypic plasticity, and the combination between these two abiotic factors can alleviate or intensify stressful effects. This study aimed to evaluate the impacts of exposure time of Cedrela fissilis Vell. seedlings to different water and light availability and the interaction of these factors. Seedlings were submitted to combinations of three shading levels – SH (0, 30 and 70%) and three water regimes based on the water holding capacity (WHC) in the substrate, constituting nine cul-tivation conditions: T1 – 0% SH + 40% WHC; T2 – 0% SH + 70% WHC; T3 – 0% SH + 100% WHC; T4 – 30% SH + 40% WHC; T5 – 30% SH + 70% WHC; T6 – 30% SH and 100% WHC; T7 – 70% SH + 40% WHC; T8 – 70% SH +70% WHC; T9 – 70% SH + 100% WHC. C. fissilis seedlings respond to water deficit, here represented by 40% WHC, regardless of exposure time, and when cultivated in full sun, the stressful effects were enhanced, acting in a synergistic manner. The condition that provided better gas exchange performance and greater total dry mass accumulation for C. fissilis seedlings was 30% shading combined with 100% WHC. C. fissilis seedlings have physiological plasticity and resilience to survive under different water and light conditions.

The manuscript presents the use of three novel technologies for the implementation of wireless green battery-less sensors that can be used in agriculture. The three technologies, namely additive manufacturing, energy harvesting, and wireless power transfer from airborne transmitters carried from UAVs, are considered for smart agriculture applications. Additive manufacturing is exploited for the implementation of both RFID based sensors and passive sensors based on humidity sensitive materials. A number of energy-harvesting systems at UHF and ISM frequencies are presented which are in position to power platforms of wireless sensors, including humidity and temperature IC sensors used as agriculture sensors. Finally, in order to provide the wireless energy to the soil-based sensors with energy harvesting features, wireless power transfer (WPT) from UAV carried transmitters is utilized. The use of these novel technologies can facilitate the extensive use and exploitation of battery-less wireless sensors which are environmentally friendly and thus “green”. Additionally, it can potentially drive precision agriculture in the next era, through the implementation of a vast network of wireless green sensors which can collect and communicate data, to airborne readers so as to support with data the Artificial Intelligence and Machine Learning based, decision making platforms.

To achieve rapid post-earthquake repair of self-centering ribbed floor flat beam frame structures, a ductile hybrid joint consisting of dog bone weakened energy dissipating steel bars connected to the upper and lower column sections through high-strength threads based on the damage control design concept is proposed. By moving the ductile energy dissipating zone out to the locally weakened section of the energy dissipating steel bars and the locally unbonded prestressed steel bars in the core area, the residual deformation was limited and the seismic performance was improved. Based on the working principle of hybrid joints, low cycle loading tests were conducted on two joint specimens to analyze the influence of lateral prestress on the seismic performance of the hybrid joints. Numerical modeling methods were used to compare the position of the energy-consuming steel bars in the composite layer and the friction performance of joints. The research results indicated that the hybrid joint had stable load-bearing, deformation, and energy dissipation capabilities, with damage primarily concentrated on the energy-consuming steel bars. Even at an inter-story displacement angle of 5.5%, the upper and lower column segments remained elastic. After unloading, the connection seam at the joint was closed, and the self-centering performance was good. When the inter-story displacement angle reached 5.5%, the lateral prestress increased from 150 kN to 250 kN, the ultimate bearing capacity of the joint increased by 16.3%, and the cumulative energy consumption increased by 30.0%. The influence of the friction coefficient of the joint surface on the structural performance was set at a threshold of 0.7. When it was less than the threshold, the ultimate bearing capacity and initial stiffness of the joint increased with an increase in the friction coefficient. After reaching the threshold, the increase in the ultimate bearing capacity of the joint slowed down, and the rate of stiffness degradation gradually accelerated. This joint had excellent seismic performance and can also achieve post-earthquake repair of structures.

The rebound behaviors of rubber balls based on ethylene-propylene-diene monomer (EPDM) / chlorinated butyl rubber (CIIR) blends were investigated systematically. A novel method was proposed to characterize the damping capacity of the EPDM/CIIR blends. The damping capacity can be represented by the rebound height of rubber balls, and lower rebound height corresponds to better damping capacity. A mathematical model expressed by an equation obtained through theoretical derivation has been proposed to predict the rebound height of the rubber balls. The energy dissipation rate (EDR) defined by the ratio of the height loss to the rebound time was proposed to further characterize the damping capacity. The EDR value shows the highest for the pure CIIR and lowest for the pure EPDM, showing a decrease trend with the increase of EPDM content in the rubber blends. By comparison one can obtain that the damping capacity of the EPDM/CIIR blends decreases with the decrease of external excitation, the conclusion of which plays a key role in the formulation design of viscoelastic damping rubber materials.

Inverse gas chromatography at infinite dilution was used to determine the surface thermodynamic properties of silica particles and PMMA adsorbed on silica, and more particularly, to quantify the London dispersive energy γsd, the Lewis acid γs+ and base γs- polar surface energies of PMMA/silica composites as a function of the temperature and the recovery fraction θ of PMMA. The polar acid–base surface energy γsAB and the total surface energy of the different composites were then deduced as a function of the temperature. In this paper, the Hamieh thermal model was used to quantify the surface thermodynamic energy of poly methyl methacrylate (PMMA) adsorbed on silica particles at different recovery fractions. A comparison of the new results was carried out with those obtained by applying other molecular models of the surface areas of organic molecules adsorbed on the different solid substrates. An important deviation of these molecular models from the thermal model was proved. The determination of γsd, γs+, γs-, and γsAB of PMMA in both bulk and adsorbed phases showed an important non-linearity variation of these surface parameters as a function of the temperature. The presence of maxima in the curves of γsd(T) highlighted the second order transition temperatures in PMMA showing beta-relaxation, glass transition and liquid-liquid temperatures. These three transition temperatures depended on the adsorption rate of PMMA on silica. The proposed method gave a new relation between the recovery fraction of PMMA and its London dispersive energy showing an important effect of the temperature on the surface energy parameters of adsorption of PMMA on silica. A universal equation relating γsd(T,θ) of the systems PMMA/silica to the recovery fraction and the temperature was proposed.

As a result of increased energy consumption, global trade has surged, and serious environmental problems have arisen. The problem is made more complicated by the fact that either environmental damage or economic advancement cannot be compromised. The elements contributing to environmental contamination must be identified and dealt with accordingly if we are to have a healthier future. In this study, what causes CO₂ emissions in Malaysia are examined using the Autoregressive distributed lag (ARDL) model using time series data from 1995 to 2020. The paper also examines the impact of energy use and economic complexity on CO2 emissions. Firstly, it is noted that the Environmental Kuznets Curve (EKC) theory holds in Malaysia. Furthermore, energy consumption has a detrimental impact on reducing CO2 emissions. Furthermore, it has been noted that a greater degree of economic complexity leads to an elevated amount of CO2 emissions over an extended period. The findings suggest significant environmental policy implications for reducing CO2 emissions in Malaysia.

BACKGROUND AND OBJECTIVE: The use of biomass for cooking carries significant health implications and can lead to adverse environmental issues such as deforestation, greenhouse gas emissions, and erosion. Despite these concerns, there is a lack of information about the nature and extent of cooking emissions in many developing countries. To address this gap, a study was conducted to assess cooking emission levels and their associated health effects among households in Dodoma City, Tanzania. METHODS: A descriptive cross-sectional design was conducted, involving 285 households in the peri-urban area of Dodoma City, Tanzania. A combination of questionnaires, observational checklists, and sampling devices (Aeroqual series 500 for Carbon Monoxide and Temptop PMD 351 for Particulate Matters) were employed for data collection, adhering to established protocols. Additionally, lung function tests were conducted with consent from the primary household cooks. Collected data were entered into an Excel spreadsheet and analyzed using STATA 17 software. FINDINGS: Out of 285 participants, 74.7% predominantly use charcoal for cooking, with 68.4% having outdoor kitchen setups. Significant differences in pollutant concentrations were observed across various fuel types (P=0.0001), with firewood emitting higher levels of particulate matter and carbon monoxide. Carbon monoxide concentrations during cooking were 6 times higher for firewood, 5 times higher for charcoal-gas, and 3 times higher for charcoal compared to WHO daily average limits. Additionally, a positive correlation between pollutant concentrations was noted (P-value = 0.0000). Lung problems 17.8% followed by eye irritation 15.7% were mentioned by those who claimed to know the health effects associated with cooking emissions. In addition, the spirometry test indicated that the majority of the participants had % predicted >80 while only 19% had % predicted below 50. CONCLUSION: Charcoal and firewood remain the primary cooking fuels in the study area despite their significant negative impacts. Our findings highlight a lack of awareness among community members regarding the health effects of biomass cooking emissions and insufficient guidance on constructing healthy kitchens. To address this, enforcing building standards, raising health awareness, and ensuring affordable access to modern fuels are crucial steps. These measures are essential for promoting healthier cooking practices and mitigating the adverse effects on households.

Resveratrol is a natural polyphenol found in various plants and fruits such as blackberries, blueberries, currants, strawberries, peanuts, and most especially in grapes. It is also present in red wine, although its content varies greatly depending on its origin. It is a phytoalexin produced by plants in response to stress, aggression from pathogens such as bacteria or fungi, or physical damage such as injury. In addition to its involvement in plant defence responses, resveratrol has been the subject of research interest due to its potential health benefits, including antioxidant properties and potential positive effects on the cardiovascular system, among others. Initial interest in its research stemmed from the so-called 'French paradox', in certain regions of France, where despite high intakes of saturated fats there was a relatively low incidence of coronary heart disease. Science wondered the factor that might be protecting the French from inflammation, vascular damage and playing a role in their longer lifespan. Thus, in the 1990s, it was hypothesized that a component of wine could be the key element. Epidemiological studies began to suggest that moderate consumption of wine, especially red wine, was associated with a reduced risk of cardiovascular disease and mortality. In vitro laboratory research supported this idea, demonstrating that resveratrol could inhibit processes involved in the development of atherosclerosis or the formation of arterial plaques, such as platelet aggregation in blood vessels and oxidative damage to LDL cholesterol. A plausible mechanism for heart protection thus emerged. Since then, an increasing number of in vitro and in vivo studies have been carried out to unravel the mechanism by which resveratrol can slow down the aging process.

The purpose of the evaluation of the Peruvian energy generation system is to project the electricity generation and demand until the year 2050. To achieve this, three alternative scenarios have been defined and analyzed using the LEAP (Long-range Energy Alternatives Planning) software. The scenarios are as follows: the first one, Business-as-Usual scenario, based on normal trends according to historical data and referencing projections made by Peruvian state entities; the second one is focused on Energy Efficiency, the highlighted characteristic is taking into consideration the efficient conditions in transmission and distribution of electric energy; and the third one, centered on Geothermal Energy, focused on the development of this type of energy source and prioritizing it. The primary purpose of this analysis is to identity advantages and disadvantages inherent in each scenario in order to get the best of each one. In this way, the intention is to propose solutions based on Peru’s national reality or possible uses of the country’s energy potential to supply its energy demand. Currently, Peru’s energy demand relies on fossil fuels, hydraulic, and thermal energy. However, there is the possibility of transforming this system into a sustainable one, by strengthening existing and growing energy sources such as solar and wind energy, and new technologies for hydraulic and thermal energy, in addition to considering geothermal energy as the main energy source in the third scenario. The new system mentioned satisfactorily indicate that the CO2 equivalent emissions decrease significantly in the third scenario, with a 15.8% reduction compared to the first scenario and a 9.7% reduction in comparison to the second. On the other hand, the second scenario shows a 5.6% decrease in CO2 emissions compared to the first, resulting from improvements in technology and energy efficiency without requiring significant modifications or considerable investments, as in the third scenario.

Mild traumatic brain injuries (mTBIs) are highly prevalent and can lead to chronic behavioral and cognitive deficits, often associated with the development of neurodegenerative diseases. The formation of reactive oxygen species (ROS) and oxidative stress have been implicated in mTBI-mediated axonal injury and pathogenesis. However, the underlying mechanisms and contributing factors are not completely understood. In this study, utilizing a murine model of repetitive mTBI (r-mTBI) involving five closed-skull concussions in young adult C57BL/6J mice, we observed a significant elevation of Na+/H+ exchanger protein (NHE1) expression in GFAP+ reactive astrocytes, IBA1+ microglia, and OLIG2+ oligodendrocytes across various brain regions (including the cerebral cortex, corpus callosum, and hippocampus). This elevation was accompanied by astrogliosis, microgliosis and the accumulation of amyloid precursor protein (APP). Concurrently, r-mTBI mice displayed impaired motor learning and spatial memory deficits. However, post-r-mTBI administration of a potent NHE1 inhibitor, HOE642, attenuated locomotor and cognitive functional deficits as well as gliosis, oxidative stress, axonal damage, and white matter damage. These findings underscore the role of NHE1 upregulation in r-mTBI-induced oxidative stress, axonal damage, and gliosis, suggesting NHE1 as a promising therapeutic target to alleviate mTBI-induced injuries and restore neurological function.

In the context of the minimally extended varying speed of light (meVSL) model, both the absolute magnitude and the luminosity distance of type Ia supernovae (SNe Ia) differ from those predicted by general relativity (GR). Utilizing the Pantheon+ data, we examine the plausibility of various dark energy models under meVSL. Both ωCDM and CPL parameterization dark energy (DE) models exhibit indications of cosmic variations in the speed of light at the 1-σ level. For Ωm0=0.30,0.31, and 0.32 with (ω0,ωa)=(−1,0), the 1-σ range of c˜˙0/c˜0(10−13yr−1) is (-8.76 , -0.89), (-11.8 , 3.93), and (-14.8 , -6.98), respectively. Meanwhile, the 1-σ range of c˜˙0/c˜0(10−12yr−1) for CPL dark energy models with −1.05≤ω0≤−0.95 and 0.28≤Ωm0≤0.32, is (-6.31 , -2.98). The value of c˜ at z=3 can exceed that of the present by 0.2∼3 % for ωCDM models and 5∼13 % for CPL models. Additionally, for viable models except for the CPL model with Ωm0=0.28, we find −25.6≤G˜˙0/G˜0(10−12yr−1)≤−0.36. For this particular model, we obtain an increasing rate of the gravitational constant within the range 1.65≤G˜˙0/G˜0(10−12yr−1)≤3.79.

This study examines the optimization of ground source heat pump (GSHP) systems and energy piles for sustainable urban development, with a focus on Southeast Asia. GSHPs, which utilize geothermal energy for indoor HVAC needs, offer a sustainable alternative to traditional systems by utilizing consistent subsurface temperatures for heating and cooling. The study highlights the importance of understanding thermal movement within the soil, especially in soft marine clays prevalent in Southeast Asia, to improve GSHP system efficiency. Using a one-dimensional finite-difference model, the study examines the effects of soil thermal conductivity and density on system performance. The results show that GSHP systems, especially when integrated with energy piles, significantly reduce electricity consumption and greenhouse gas emissions, underscoring their potential to mitigate the urban heat island effect in densely populated areas. Despite challenges posed by the region's hot and humid climate, which could affect long-term effectiveness, the study highlights the need for further study, including field experiments and advanced modeling techniques, to optimize GSHP configurations and fully exploit geothermal energy in urban environments. The study's insights into soil thermal dynamics and system design optimization contribute to the advancement of sustainable urban infrastructure development.

Plant growth regulators (PGRs) and deficit irrigation (DI) play a crucial strategic role in sustaining agricultural yield and reducing water stress in drought prone areas. The study was carried out in 2021-2022 to assess the impact of various PGRs (SA & NAA) & irrigation levels (60% Epan, 80 % Epan, and 100 % Epan) with DI & partial root drying (PRD) irrigation strategies. PGR application boosted fruit yields and demonstrated its significance in reducing water stress by lowering canopy temperature, maintaining higher relative water content in the leaves, modifying stomatal opening, and increasing photosynthetic rate. PGRs were used to assess the increased accumulation of total phenols, flavonoids, and improved antioxidant activity. Results indicated that exogenous use of PGRs like SA+NAA in conjunction with 80% irrigation levels increased fruit yield (31.97 and 40.38%) and water productivity (64.92 and 75.39%) for DI and PRD treatments, respectively. Thus standardizing irrigation and crop management practices including PGR application can be recommended to boost pomegranate productivity particularly in water-scarce environments.

Buildings’ thermal energy needs are inherently linked to climate conditions. Consequently, it is crucial to evaluate how climate changes affect these energy demands. Despite extensive analysis, a comprehensive assessment involving a diverse range of building types has not been consistently conducted. The primary objective of this research is to perform a coherent evaluation of the influence of climate changes, construction element properties, and the Heating, Ventilation, and Air Conditioning (HVAC) system type of control on the energy requirements of six buildings (residential, services, and commercial). The buildings are considered located in a temperate Mediterranean climate. Our focus is on the year 2070, considering three distinct climatic scenarios: (i) maintaining the current climate without further changes, (ii) moderate climate changes, and (iii) extreme climate changes. The buildings are distributed across three different locations, each characterized by unique climatic conditions. Buildings’ envelope features a traditional External Thermal Insulation Composite System (ETICS) and expanded polystyrene (EPS) serves as thermal insulation material. Two critical design factors are explored: EPS thickness ranging from 0 (no insulation) to 12 cm; and horizontal external fixed shading elements varying lengths from 0 (absence) to 150 cm. Six alternative setpoint ranges are assessed for the HVAC system control: three based on the Predicted Mean Vote (PMV) and three based on indoor air temperature (Tair). Results were obtained with a validated in-home software tool. They show that, even under extreme climate conditions, the application of thermal insulation remains energetically favorable, however its relative importance diminishes as climate severity increases. Then, proper insulation design remains important for energy efficiency. The use of external shading elements for glazing (e.g., overhangs, louvers) proves beneficial in specific cases. As climate changes intensify, the significance of shading elements grows. Thus, strategic placement and design are necessary for good results. The HVAC system’s energy consumption depends on the level of thermal comfort requirements, on the climate characteristics and on the building’s type of use. As climate change severity intensifies, energy demands for cooling increase, while energy needs for heating decrease. However, it’s essential to recognize that the impact of climate changes on HVAC system energy consumption significantly depends on the type of building.

Amidst worsening climate change, drought stress imperils global agriculture, jeopardizing crop yields and food security, necessitating urgent exploration of sustainable methods like biopriming, harnessing beneficial microorganisms to bolster plant resilience. Recent research has revealed diverse biological compounds with versatile applications produced by Schizophyllum commune, rendering this fungus as a promising contender for biopriming applications. For the first time this study aimed to investigate,the potential of S. commune exo- (EPSH) and intra-PSH (IPSH), isolated from two strains: Italian (ITA) and Serbian (SRB) under submerged cultivation, in enhancing the resilience of Pisum sativum L. seeds through biopriming technique. Testing of seed quality of bioprimed, hydroprimed, and unprimed seeds was done using a germination test, under optimal and drought conditions. In optimal conditions, the IPSH SRB increased germination energy by 5.50% compared to the control, while the highest percentage of germination (94.70%) was shown after biopriming with PSH isolated from the ITA strain. Additionally, all assessed treatments resulted in a boost in seedling growth and biomass accumulation, where the ITA strain demonstrated greater effectiveness in optimal conditions, whereas the SRB strain showed superiority in drought conditions. The drought tolerance indices increased significantly in response to all examined treatments during the drought, with EPSH ITA (23.00%) and EPSH SRB (24.00%) demonstrating the greatest effects. Results demonstrate a significant positive influence of fungal PSH, indicating their potential as biopriming agents and offers insights into novel strategies for agricultural resilience in the face of changing environmental conditions.

Osteoporosis is considered a serious public health problem, particularly affecting the postmenopausal period. In 2018, in the Republic of Kazakhstan the total and primary incidence was 10 and 3.7 cases per 100,000 adults, respectively. The objective is to study osteoporosis prevalence and indicate main factors affecting low bone mineral density by screening adult population of Abay region, Kazakhstan. The target group were 641 respondents aged between 18 and 65 years old, Kazakh population living in Abay region since birth. All participants filled out questionnaire and had a bone mineral density measurement by dual energy X-ray absorptiometry (DXA) between July 15, 2023 and February 29, 2024. Logistic regression analysis was conducted to assess the association between low bone mineral density and key demographic characteristics, aforementioned lifestyle factors and nutrition habits. We identified the prevalence of low bone density and osteoporosis at the level of 34.1% with the highest prevalence in the older population group (50+ years) - 48.3%. Regression analysis revealed a number of indicators associated with the likelihood of bone sparing. However, only 4 of these showed significance in the final multivariate model (R2=22.4%). These included age (AOR 1.05), body mass index (AOR 0.92), fracture history (AOR 1.64), consumption of nuts and dried fruits were associated with lower prevalence of osteoporosis (AOR 0.48). Our study was the first in Kazakhstan that investigates the association of key demographic, behavior and anamnestic factors with low mineral density.

The aim of this work was to describe the physiological limitations induced under drought conditions in young sweet orange trees, including the crop capability to recuperate its physiological status once re-watering, and after a water withholding. The trial was conducted during two consecutive months (July and August) in two-years old sweet orange trees. Three irrigation treatments were arranged: A full irrigation treatment; (FI); a low-frequency deficit-irrigation treatment (LFDI); and a sustained-deficit irrigation (SDI) treatment. The obtained results showed that for Stem values below -1.5 MPa, significant decreases in gas exchange rates, evidencing diffusive limitations to drought stress. Additionally, there was evidence of increased osmolyte synthesis, compatible as a defensive response to prevent oxidative damage. Likewise, the isohydric behaviour observed also resulted in significant decreases in gs even for moderate stress situations. In addition, it was observed that in the LFDI treatment, the stress levels reached caused a significant increase in the levels of Pro and MDA, which were not equal to those detected in FI during the recovery periods, which leads us to assume that potential values below -1.8 MPa would be causing significant oxidative damage with no capacity for subsequent recovery, and probably affecting the final yield.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

Nowadays, the identification and characterization of grapevine cultivars resilient to climate and water stress while preserving quality traits is crucial for the wine industry. Therefore, the objective of this work was to characterize according to their aromatic potential 9 white and 6 red minority cultivars recently recovered from Castilla-La Mancha region (Spain), subjected at two different water deficit regimes: rainfed, with subsistence irrigation, and irrigated. For this, the varietal aromatic potential index (IPAv) and the detailed aromatic composition were analyzed by HS-SBSE-GC/MS, in extracts of two different ph. For IPAv values, red varieties did not show a clear trend with respect to irrigation. However, in white minority varieties, higher values were obtained under irrigation conditions. Thus, a clear differentiation of the minority varieties in comparison to the references was observed, primarily attributed to the content of esters and acids, in both white and red varieties. A notable contrast was observed at different pH, indicating a greater extractability of certain compounds like linalool, under more acidic conditions. This suggests that some recovered minority cultivars could be promising for cultivation in semi-arid regions with limited water, contributing to the wine sector sustainability in the future.

The evolutionary cancer cell biology ECCB explains the deep homology existent between the life cycle of cancer and protists. Due to their origin and sensitivity to oxygen, all non-gametogenic germ lines and germ stem cells (GSCs), including human adult stem cells (ASCs) and cancer stem cells (CSCs), suffer severe DNADSB damage when exposed to stress oxygen content above 6.0% O2 (Urgermline hyperoxia) as occurring in tissue and bloodstream. As a result, GSCs/ASCs/ CSCs lose their stemness potential and convert from a functional asymmetric cyclic phenotype (ACD phenotype) to a dysfunctional symmetric phenotype capable of defective symmetric proliferation (DSCD) that is, however, unable to repair genomic degradation. Genome reconstruction occurs through evolutionary mechanisms evolved by the common ancestor of amoebozoans, metazoans, and fungi. They complete the cycle by removing the damage, reconstructing the functional genome, and reinstating the ASC phenotype. The stemness life cycle acts not only during carcinogenesis, tumorigenesis, and recurrence but also in the life cycle of protists.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

A single-center, randomized, double-blind, placebo-controlled clinical trial with two arms was conducted in 71 healthy subjects suffering from sleep disturbances, which were treated with a dietary supplement based on an extract of Aloysia citrodora (or Lippia citriodora, lemon verbena) (n = 33) for 90 days. Subjects in the placebo group (n = 38) received capsules of microcrystalline and maltodextrin with the same organoleptic properties. Between-group significant differences in favor of the experimental group were found in the visual analogue scale (VAS) score rating sleep quality; overall score, sleep latency and sleep efficiency of the Pittsburg Sleep Quality Index (PSQI); and sleep latency, sleep efficiency, wakefulness after sleep onset and duration of awakening assessed by actigraphy. Plasma nocturnal melatonin levels also increased significantly in the experimental group. Changes in anthropometric parameters and physical activity levels were not found. This study shows that the administration of a dietary supplement comprised lemon verbena administered for 3 months was associated with a significant improvement of sleep quality as compared with placebo in a population of healthy subjects with sleep problems. Improvements were also apparent at the mid-study visit after 45 days of supplementation.

This paper describes an entropy equation that can be used for measuring energy. It originated from measuring economy in AI models, where the assumption would be that any organic system makes use of energy efficiency to form its structures. Looking at clustering and cohesion resulted in the equation E = (mean * variance). It was apparent however, that it was a very generic type of equation and it could be adjusted so that distance represents mean. This new version was applied to the domain of physics and the universe, when the equation can support the idea that work is done through the energy released by the 'change' in entropy. A comparison with Einstein's relativity equation is made and also the audacious suggestion that a black hole has only potential energy inside, which converts to kinetic energy after a Big Bang, for example. From that suggestion, a universal theory about state change can be made.

Salt stress is a major limiting factor for alfalfa yield due to its relatively low salt tolerance. High soil salinity adversely impacts alfalfa growth and development, leading to reduced yield. Melatonin (MT) is known to play a significant role in enhancing plant resistance to abiotic stresses. However, the mechanisms underlying melatonin-mediated abiotic stress responses, particularly salt stress, are not well understood. To address this gap, we conducted a study focusing on germinating alfalfa seeds under salt stress. Physiological indexes and transcriptomics analyses were carried out on the germinated seeds to investigate the effects of melatonin on alfalfa seedlings under salt stress conditions. Our results revealed that the application of melatonin led to an increase in shoot length and fresh weight of alfalfa seedlings under salt stress. Moreover, key physiological indexes such as peroxidase (POD) activity and glutathione (GSH) content were enhanced, while levels of malondialdehyde and superoxide anions decreased. Transcriptomic analysis identified a total of 2,131 differentially expressed genes in the salt-treated group, with 726 up-regulated and 1,405 down-regulated genes, while the MT-treated group showed 2896 differentially expressed genes, of which 1,097 were up-regulated and 1,799 were down-regulated. Further, KEGG enrichment analysis highlighted the enrichment of differentially expressed genes in pathways including flavonoid biosynthesis, ABC transporter, glutathione metabolism, and the MAPK signaling pathway, with these pathways more significantly enriched in the MT-treated group. These findings collectively suggest that melatonin plays a crucial role in alfalfa's response to salt stress and offer new insights into the genomic mechanisms underlying melatonin-mediated salt tolerance in alfalfa.

The results shown in this paper extend our research group's previous work, which presents the theoretically achievable hydrogen engine-out NOx (H2-NOx) Pareto front of a hydrogen hybrid electric vehicle (H2-HEV). While the Pareto front is calculated offline, which requires significant computing power and time, this work presents an online-capable algorithm to tackle the energy management of a H2-HEV with explicit consideration of the H2-NOx trade-off. Through the inclusion of realistic predictive data on the upcoming driving mission, a model predictive control algorithm (MPC) is utilized to effectively tackle the conflicting goal of achieving low hydrogen consumption while simultaneously minimizing the NOx. In a case study it is shown that the MPC is able to satisfy user-defined NOx limits over the course of various driving missions. Moreover, a comparison to the optimal Pareto front highlights the MPC's ability to achieve close-to-optimal fuel-performance for any desired cumulated NOx target on four realistic routes for passenger cars.

Background: Nutritional status and oxidative stress have been implicated in the pathogenesis and persistence of long COVID, but data in patients undergoing hemodialysis (HD) are limited. The present study aimed to investigate the association between pre-infection nutritional status, oxidative stress, and one-year long COVID persistence in HD patients. Methods: This prospective observational cohort study enrolled 115 HD patients with confirmed COVID-19. Nutritional status was assessed using the Controlling Nutritional Status (CONUT) score twice: before infection and three months post-infection. Oxidative markers included malondialdehyde (MDAs), ceruloplasmin, transferrin, and sulfhydryl groups. The endpoint was one-year long COVID persistence. Results: Moderate pre-infection CONUT scores were associated with heightened severe undernutrition risk (p < 0.0001), elevated MDAs (p < 0.0001), and reduced ceruloplasmin levels (p = 0.0009) at three months post-COVID-19 compared to light CONUT scores. Pre-infection CONUT score independently predicted post-COVID oxidative damage [OR 2.3 (95%CI 1.2; 4.6), p < 0.0001] and one-year long COVID persistence [HR 4.6 (95%CI 1.4; 9.9), p < 0.0001], even after adjusting for potential confounders. Conclusion: Moderate pre-infection undernutrition in patients undergoing HD associated with increased post-COVID oxidative stress intensity and heightened risk of one-year long COVID persistence.

Sleep and stress significantly affect emotions, productivity, and overall well-being, crucial for optimal health and performance. However, limited research examines how Nepalese nurses' quality of life relates to their sleep quality and stress levels. This study aims to assess this relationship among nurses in private hospitals in Kathmandu. Three private hospitals were selected for this cross-sectional analytical study. Eligible nurses were chosen through purposive sampling, and data were analysed using IBM SPSS v25, employing Chi-square tests and logistic regression analysis. Research revealed a high rate of poor sleep quality (83.9%) among individuals with a mean age of 24.33 ± 3.08 years. Initially, significant associations were found with the factors like bachelor's degree, no tobacco use, absence of insomnia, good sleep quality, and low stress with good quality of life. After adjustment, the association with bachelor's degree [AOR:2.025, CI at 95%: 1.021-4.016, p

(1) Background: Alzheimer’s disease (AD) presents a significant challenge in terms of discovering novel diagnostic methods and therapies. Previous research has shed light on the neuroprotective properties of Apelin-13 in neurodegenerative disorders. However, elucidating the mechanism underlying its efficacy in combating AD-related nerve injury is imperative. In this study, we aimed to investigate the mechanism of action of Apelin-13 in an in vivo model of AD induced by streptozocin (STZ); (2) Methods: We utilized an STZ-induced nerve injury model of AD in mice to investigate the effects of Apelin-13 administration. The Apelin-13 was administered intranasally, and cognitive impairment was assessed using standardized behavioral tests. The main methods included behavioral assessment, histological analysis, and biochemical assays to evaluate synaptic plasticity and oxidative stress signaling pathways; (3) Results: Our findings indicate that intranasal administration of Apelin-13 ameliorated cognitive impairment in the STZ-induced AD model. Furthermore, we observed that this effect was potentially mediated through the enhancement of synaptic plasticity and attenuation of oxidative stress signaling pathways; (4) Conclusions: The results of this study suggest that intranasal administration of Apelin-13 holds promise as a therapeutic strategy for preventing neurodegenerative diseases such as AD. By improving synaptic plasticity and mitigating oxidative stress, Apelin-13 may offer a novel approach to neuroprotection in AD and related conditions.

Diabetes mellitus (DM) poses a significant challenge to global health, with its prevalence projected to rise dramatically by 2045. This narrative review explores the bidirectional relationship between periodontitis (PD) and type 1 diabetes mellitus (T1DM), focusing on cellular and molecular mechanisms derived by the interplay between oral microbiota and the host immune response. A comprehensive search of literature published between 2008 and 2023 was conducted to elucidate the association between these two diseases. Preclinical and clinical evidence suggests a bidirectional relationship, with individuals with T1DM exhibiting heightened susceptibility to periodontitis, and vice versa. The review includes recent findings from human clinical studies, revealing variations in oral microbiota composition in T1DM patients, including increases in certain pathogenic species such as Porphyromonas gingivalis, Prevotella intermedia, and Aggregatibacter actinomycetemcomitans, along with shifts in microbial diversity and abundance. Molecular mechanisms underlying this association involve oxidative stress and dysregulated host immune responses, mediated by inflammatory cytokines such as IL-6, IL-8, and MMPs. Furthermore, disruptions in bone turnover markers, such as RANKL and OPG, contribute to periodontal complications in T1DM patients. While preventive measures to manage periodontal complications in T1DM patients may improve overall health outcomes, further research is needed to understand the intricate interactions between oral microbiota, host response, periodontal disease, and systemic health in this population.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

Abstract: : 2,3-dihydro-5,6,7,8-tetranitro-1,4-benzodioxine (TNBD), molecular formula =C8H4N4O10 is a completely nitrated in aromatic ring 1,4-benzodioxane derivative. The con-venient method of TNBD synthesis was developed (yield=81 %). The detailed structure of this compound has been investigated by X-ray crystallography. The results of differential thermal analysis (DTA) obtained with twice re-crystallized material showed onset at 247 and isoterm at 288 0C, with further total degradation at 300 0C. The experimental density 1,85 g/cm3 of TNBD was determined by X-ray crystallography. The spectral properties of TNBD (NMR, FT-IR, Ra-man) were explored. The detonation properties of TNBD calculated by EXPLO 5 code was slightly superior in comparison to standard high energy material - tetryl (detonation velocity of TNBD - 7727 m/s; detonation pressure - 278 kbar; tetryl – 7570 m/s and 226.4 kbar at 1.614 g/cm3, or 260 kbar at higher density - 1.71 g/cm3. The obtained preliminary results might suggest TNBD can be a potential thermostable high energy and density material (HEDM).

The conventional measure of cosmic acceleration, denoted as \( q \), relies heavily on the frame of reference and operates within a 3D space-like coordinate system, potentially leading to misinterpretations of underlying physics. In this study, we propose a novel measure, \( q_E \), grounded in distances between causal events in 4D null space. We compare \( q_E \) with the standard \( q \) using observational data from supernovae (SN) and radial galaxy/quasar (QSO) clustering (BAO) to find a better alignment of data with \( q_E \). Our analysis indicates that cosmic expansion, when viewed in the rest frame, is decelerating, with events confined by an Event Horizon akin to that of a Black Hole interior. Rather than invoking new dark energy or modified gravity, we propose that \( \Lambda \) corresponds to a boundary term exerting an attractive influence, analogous to a rubber band resisting further expansion and preventing horizon crossing of events. Contrary to prevailing notions, interpreting current cosmic expansion measurements as deceleration, rather than acceleration, offers a more accurate depiction of observed phenomena and the underlying physics. This reevaluation prompts further investigation into the nature of cosmic expansion, as well as the exploration of alternative frameworks and measures in cosmology.

A large share of the reinforced-concrete (RC) building stock in Mediterranean countries faces a dual challenge of seismic vulnerability and energy inefficiency, calling for urgent renovation ef-forts. While energy upgrades have been the focus of previous renovation policies, recent research highlights the critical need for integrated retrofitting solutions that address both structural integ-rity and energy performance. Multi-criteria decision making (MCDM) approaches are a promis-ing tool for optimizing the combined choice of these integrated interventions, considering various decision variables (DVs), of economic, social, environmental, and technical nature. To understand the impact of climate and seismic hazard conditions on multi-criteria based retrofitting assess-ment, a case-study RC school building is selected and assumed to be located in three distinct cli-mate conditions - cold, mild, and warm - and three seismic hazard levels – low, medium and high. Moreover, given the complexity and challenges of quantifying seismic performance metrics for practitioners, an available simplified (practice-oriented) approach is compared herein with a more thorough research-based one for quantifying the seismic performance of RC buildings with-in the MCDM framework. Both approaches are applied to the case-study building, considering twelve possible combinations of energy and seismic interventions. The accuracy of the practice-oriented approach and its impact on the retrofitting rankings is evaluated, emphasizing the im-portance of accessible and efficient evaluation methods in facilitating informed decision-making for building renovation.

The work aims to improve the battery performance in hybrid electric vehicles (HEVs) by reducing the vehicle speed. We develop a specific protocol for managing battery use and optimizing the energy consumption rate to achieve this goal. The protocol automatically controls the driving operation, avoiding incompatible driving patterns with energy-saving mode and performance improvement. The protocol is submitted to a simulation process to predict the energy rate lowering and battery performance enhancement. The proposed protocol applies to any hybrid electric vehicle type and route conditions since it uses vehicle mass, drag and rolling coefficients, and road slope as variable parameters to determine the minimum energy consumption rate. We run experimental tests to validate the simulation data and the proposed protocol. Furthermore, the protocol applies to variable starting vehicle speeds, from 10 to 50 km/h, corresponding to the current driving patterns, sport, normal, and eco, set up by car manufacturers. A reduction of 10% in vehicle speed in urban and peripheral routes achieves a minimum energy rate, enhancing battery management. Current vehicle speed shows a deviation from optimum management of 18% while applying the vehicle speed reduction limits the deviation to 0.2%. Experimental results show a good agreement with simulation data with 94% accuracy. We tested the protocol for urban and peripheral routes with maximum vehicle speed limits of 60 and 90 km/h.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Hypertensive diseases of pregnancy (HDP) represent a global clinical challenge, affecting 5-10% of women and leading to complications for both maternal well-being and fetal development. At the heart of these complications is endothelial dysfunction, with oxidative stress emerging as a pivotal causative factor. The reduction in nitric oxide (NO) bioavailability is a vital indicator of this dysfunction, culminating in blood pressure dysregulation. In the therapeutic context, although antihypertensive medications are commonly used, they come with inherent concerns related to maternal-fetal safety, and a percentage of women do not respond to these therapies. Therefore, alternative strategies that directly address the pathophysiology of HDP are required. This article focuses on the potential of the nitrate-nitrite-NO pathway, abundantly present in dark leafy greens and beetroot, as an alternative approach to treating HDP. The objective of this review is to discuss the prospective antioxidant role of nitrate. We hope our discussion paves the way for using nitrate to improve endothelial dysfunction and control oxidative stress, offering a potential therapy for managing HDP.

The objective of this study was to investigate age-related changes in cashmere production and the population of active secondary hair follicles in cashmere goats across different age groups, as well as to explore the association between secondary hair follicle activity and oxidative stress. A total of 104 adult Inner Mongolian ewe goats, aged between 2 and 7 years old, were randomly selected as experimental subjects. Skin samples were collected in August 2020 and cashmere samples were collected in April 2021. The cashmere fiber yield, staple length, and diameter showed age-related variations in cashmere goats aged 2 to 7 years (P < 0.05). Cashmere production was higher in goats aged 2-4 years compared to those aged 5-7 years (P < 0.05). There were no significant differences in the population of primary and secondary hair follicles among goats aged 2 to 7 years. However, the population of active secondary hair follicles varied significantly with age, with the younger group (aged 2-4 years) having a higher population than those aged 5 – 7 years (P < 0.05). A moderate negative correlation was observed between cashmere fiber diameter and the population of active secondary hair follicles (P < 0.05). Age-related variations in skin antioxidant capacity and oxidative damage were observed among cashmere goats aged 2 to 7 years old (P < 0.05). Goats aged 2 to 4 years exhibited higher antioxidant capacity and lower oxidative damage (P < 0.05). Interestingly, the skin antioxidant capacity and oxidative damage exhibited significant positive and negative correlations, respectively, with the population of active secondary hair follicles (P < 0.05). This study presents a novel approach to enhance the activity of secondary hair follicles and improve cashmere production performance through the regulation of oxidative stress.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

This general review assesses the impact of physical exercise on oxidative and nitrosative stress and the counteractive role of antioxidants, drawing from a systematic literature search up to March 2024 in databases like PubMed and Web of Science. The review highlights studies on the effect of exercise on the production of reactive oxygen species (ROS) and reactive nitrogen species (RNS) and antioxidant responses in both human and animal models based on rigorous inclusion and exclusion criteria. Due to the variety of exercise types and participants' characteristics, a narrative synthesis approach was adopted. The findings indicate that moderate exercise boosts antioxidant defenses, known as hormesis, whereas excessive physical activity may increase oxidative and nitrosative damage. The review also explores the complex effects of antioxidant supplementation, revealing that while natural dietary antioxidants support health, high-dose supplements could potentially hinder positive adaptations to exercise. Recommendations for athletes and the general active population highlight the importance of balancing exercise and dietary intake to optimize health benefits. The review concludes with a call for more detailed research on tailored exercise and nutrition plans to dissect these intricate relationships further.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

The reduction of PV prices and interest in energy independence accelerate the adoption of residential battery storage. This storage can support various functions of an energy system undergoing decarbonization. In this work, operative benefits of the storage from the system perspective, namely, generation cost reduction and congestion mitigation, are investigated. Germany is chosen as a case study due to its strong reliance on variable renewable energy. For the analysis, an economic dispatch model with a high spatial resolution is coupled with a Pan-European transmission grid model. It is shown that the system's generation costs are highest when the assets are used only to maximize the PV self-consumption, and the costs are lowest when the storage also reacts to the market dynamics. This amounts to 6% cost reduction. Both operation strategies result in an equal level of grid congestion and infrastructure loading. This is improved with a strategy that accounts regional peak reduction as a secondary objective. The high congestion level emphasizes the grid expansion need to keep pace with the generation and electrification expansion necessary to decarbonize other sectors. Lastly, policymakers should enable multipurpose utilization, e.g., via the introduction of market-oriented retail electricity prices with intervention options for grid operators.

Abstract—The static and fatigue analysis of plates with holes, made of 2D woven roving composites, is conducted. The parametrization of convex holes is proposed. Experimental results of specimens without holes and with different shapes of notches are discussed. The fatigue behaviour is considered with the use of the low cycle fatigue method. The analysis is supplemented by the numerical finite element modeling. The present work is an extension of the results discussed in the literature. The finite element modeling of plates with holes is presented in details in Ref [1-3] including also the problems of the accuracy. The experimental results and the form of specimens are shown in Ref [4]. Two parametrical description of static and fatigue behaviour of plates with holes characterizes the goal and the novelty of the paper. The fuzzy approach is employed to reduce the number of experimental data [5].

Observation of the distribution of the velocity of galactic rotation curves differed from their expected centripetal form and lead to the notion of Dark Matter or modifications to Newtonian and General Relativity, such as MOND, TeVeS and the like and even Quantised Inertia. We aim to show that General Relativity with Dark Energy/the Cosmological Constant is all that is needed, with the proviso that the Cosmological Constant can increase in the presence of a light flux or some other factor from galaxies and become gravitating; the need for Dark Matter may be abated.

Microgrids (MGs) have evolved as critical components of modern energy distribution networks, providing increased dependability, efficiency, and sustainability. Effective control strategies are essential for optimising MG operation and maintaining stability in the face of changing environmental and load conditions. Traditional rule-based control systems are extensively used due to their interpretability and simplicity. However, these strategies frequently lack the flexibility for complex and changing system dynamics. This paper provides a novel method called hybrid intelligent control for adaptive MG that integrates basic rule-based-control and deep learning techniques, including gated recurrent units (GRU), basic recurrent neural network (RNN) and long short-term memory (LSTM). The main target of this hybrid approach is to improve MG management performance by combining the strengths of basic rule-based systems and deep learning techniques. These deep learning techniques readily enhance and adapt control decisions based on historical data and domain-specific rules, leading to increasing system efficiency, stability, and resilience in adaptive MG. Our results show that the proposed method optimises MG operation, especially under demanding conditions such as variable renewable energy supply and unanticipated load fluctuations. This study investigates special RNN architectures and hyper-parameter optimization techniques with the aim of predicting power consumption and generation within the adaptive MG system. Our promising results show the highest-performing models indicating high accuracy and efficiency in power prediction. The finest-performing model accomplishes an R2 value close to 1, representing a strong correlation between predicted and actual power values.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

It is already known that a simple nonlocal de Sitter gravity model, which we denote as dS gravity, contains an exact vacuum cosmological solution which mimics dark energy and dark matter and is in very good agreement with the standard model of cosmology. This success of dS gravity motivated us to investigate how it works at lower than cosmic scale – galactic and the solar system. This paper contains our investigation of the corresponding Schwarzschild-de Sitter metric of the dS gravity model. To get exact solution, it is necessary to solve the corresponding nonlinear differential equation, what is a very complicated and difficult problem. What we obtained is a solution of linearized equation, which is related to space metric far from the massive body, where gravitational field is weak. The obtained approximate solution is of particular interest for examining the possible role of non-local de Sitter gravity dS in describing the effects in galactic dynamics that are usually attributed to dark matter. The solution has been tested on the Milky Way and the spiral galaxy M33 and is in good agreement with observational measurements.

Pediatric psychology action in the pediatric clinical-surgical high complexity unit has become increasingly necessary. It allows for the possibility of integrating complex pediatric clinical-surgical operations by reducing painful effects on the emotional world of children and adolescents. The pediatric psychologist in a pediatric unit continuously oversees children and adolescents (C/A) throughout the entire therapeutic process, extending activity to parents and healthcare personnel. In ill children and adolescents, physical pain and psychological suffering follow, with minimal temporary variations, the same clinical path with continuous changes which put a strain on the ability of children, adolescents, parents and healthcare staff to cope with stress.

The scope of this work is to empirically check and prove the practical applicability of the Primordially Hydridic Earth (hereinafter PHE) concept for early exploration of the resources of naturally occurring hydrogen. With the PHE concept postulates interpreted within the local geological, tectonic, petrological and geophysical context, the reconnaissance plan, as well as the field exploration and data acquisition programs, were put together and implemented in the field. The results obtained from the surface (

Differences between the quantum mechanical and relativistic concepts of time observed in GPS satellites are accounted for by applying the equivalence principle to the transitioning electron of an atomic clock. It allows a differential equation of motion to be derived for the electron in the Minkowski space between electron shells. Using Hamilton’s principle we transform the differential equation relativistically into an integral equation of motion, the time integral of a Lagrangian. This newly derived equation accounts for the abstract mathematics of the more familiar non-relativistic model by means of a physical interpretation. Abstract rotations in Hilbert space are replaced by the rotations of real particle field geometries in Minkowski space. Because the properties of energy are universal the same equations are then used to describe the field geometry of galaxies despite vast differences in lifetime. They reveal a symmetry between the electromagnetic fields of atoms and the gravitational fields of galaxies due to similarities in the exchange of energy by radial and transverse fields. Our analysis reveals that the conjugate variables energy and time permit differences between atomic and galactic structure to be compared in a more intuitive way than by means of the differential equations of motion which use the conjugate variables position and momentum.

The main source of electricity worldwide stems from fossil fuels, contributing to air pollution, global warming, and associated adverse effects. This study explores wind energy as a potential alternative. Nevertheless, the variable nature of wind introduces uncertainty in its reliability. Thus, it is necessary to identify an appropriate machine learning model capable of reliably forecasting wind speed under various environmental conditions. This research compares the effectiveness of artificial neural networks (ANN) and convolutional neural networks (CNN) in predicting wind speed across three locations in South Africa, characterised by different weather patterns. Empirical results show that CNN outperforms ANN in accurately forecasting wind speed under different weather conditions. This superiority is likely due to the inherent architectural attributes of CNNs, including feature extraction capabilities, spatial hierarchy learning, and resilience to spatial variability. These results could be useful to decision-makers in the energy sector.

Dealing with and maintaining high-quality standards in the design and construction phases is challenging, especially for on-site construction. Issues like improper implementation of building components and poor communication can widen the gap between design specifications and actual conditions. To prevent this, particularly for energy-efficient buildings, it's vital to develop resilient, sustainable strategies. These should optimize resource use, minimize environmental impact, and enhance livability, contributing to carbon neutrality by 2050 and climate change mitigation. Traditional post-occupancy evaluations, which identify defects after construction, are impractical for addressing energy performance gaps. A new, real-time inspection approach is necessary throughout the construction process. This paper suggests an innovative guideline for prefabricated buildings, emphasizing digital 'self-instruction' and 'self-inspection'. These procedures ensure activities impacting quality adhere to specific instructions, drawings, and 3D models, incorporating relevant acceptance criteria to verify completion. This methodology, promoting alignment with planned energy-efficient features, is supported by BIM-based software and Augmented Reality (AR) tools, embodying Industry 4.0 principles. BIM and AR bridge the gap between virtual design and actual construction, improving stakeholder communication and enabling real-time monitoring and adjustments. This integration fosters accuracy and efficiency, key for energy-efficient and Nearly Zero-Energy Buildings, marking a shift towards a more precise, collaborative, and environmentally sensible construction industry.

In today's world, the significance of reducing energy consumption globally is increasing, making it imperative to prioritize energy efficiency in the 5th Generation (5G) networks. However, it is crucial to ensure that these energy-saving measures do not compromise the Key Performance Indicators (KPIs) such as user experience, quality of service (QoS), or other important aspects of the network. To address this challenge, advanced wireless technologies have been incorporated into the design of 5G networks across various network layers. Given the rapid advancements in Artificial Intelligence (AI) and emerging technology trends such as Machine Learning (ML), which is considered a subset of AI, the integration of such trends into 5G networks has become a significant area of research. The primary objective of this survey is to analyze AI integration into 5G networks for enhanced energy efficiency. By exploring this intersection between AI and 5G, we aim to identify potential strategies and techniques for optimizing energy consumption while maintaining the desired network performance and user experience.

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

Dysregulation of the Cyclin-dependent kinase 8 (CDK8) activity has been associated to many diseases including the colorectal and breast cancer. As usual in the CDK family, the activity of CDK8 is controlled by a regulatory protein called cyclin C (CycC). But while human CDK family members are generally activated in two steps that is, the binding of the cyclin to CDK and the phosphorylation of a residue in the CDK activation loop, CDK8 does not require the phosphorylation step to be active. Another peculiarity of CDK8 is its ability to be associated to CycC while adopted an inactive form. These specificities raise the question of the role of CycC in the complex CDK8-CycC, which appears to be more complex than for the other members of CDK family. Through MD simulations and binding free energy calculations, we investigated the effect of CycC on the structure and dynamics of CDK8 on the one hand, and the structural molecular basis of the protein-protein interaction between the two partners on the other hand. We found that CycC has a stabilizing effect on CDK8 and identified specific interaction hotspots within its interaction surface compared to other human CDK/Cyc pairs. Targeting these specific interaction hotspots could be a promising approach in terms of specificity, to effectively disrupt the interaction between CDK8. The simulation of the conformational transition from the inactive to the active form of CDK8 suggests that the residue Glu99 of the CycC may assume the role of the missing phosphorylation step in the activation mechanism of CDK8. In a more general view, these results point the importance of keeping the CycC in computational studies when studying the human CDK8 protein in both the active and the inactive form.

This research aimed to investigate the relationship between climate policy uncertainty (CPU), clean energy (ENERGY), carbon emission allowance prices (CARBON), and Bitcoin returns (BTC) for the period from August 2012 to August 2022. The empirical analysis strategies utilized in this study included the Fourier Bootstrap ARDL long-term coefficient estimator, Fourier Granger Causality, and Fourier Toda Yamamoto Causality methods. Following the confirmation of cointegration among the variables, we observed a positive relationship between BTC and CARBON, a positive relationship between BTC and CPU, and a negative relationship between BTC and ENERGY. In terms of causal associations, we identified one-way causality running from CARBON to BTC, BTC to CPU, and BTC to the ENERGY variable. The study underscores the potential benefits and revenue opportunities for investors seeking diversified investment strategies in light of climate change concerns. Furthermore, it suggests actionable strategies for policymakers, such as implementing carbon taxes and educational campaigns, to foster a transition towards clean energy sources within the cryptocurrency mining sector and thereby mitigate environmental impacts.

In our investigation of the time evolution of energy states Einstein’s interpretation from more than a century ago is found to have greater internal consistency than that of non-relativistic quantum mechanics. We choose to align more closely with his methods by abandoning the non-relativistic Hamiltonian method, which has been the standard for nearly a century, in favor of a relativistically correct Lagrangian method. Integral equations of motion for the absorption and emission of radiation are derived that underlie and anticipate the differentially motivated Schrödinger equation. This new interpretation applies to a large volume of experimental evidence of both classical and quantum mechanical origin. Among the examples discussed in support are Planck’s law describing black body radiation, matrix mechanics, the function of the simplest quantum mechanical system an electron cyclotron, chaos theory, and evolutionary biology.