A non-destructive analysis of proximate parameters (moisture content, MC; volatile matter, VM; fixed carbon, FC; and ash content) for a variety of chipped and ground biomasses was investigated through a combination of thermogravimetric analysis (TGA) and near-infrared spectroscopy (NIRS) with partial least squares regression (PLSR). In this study, the thermogravimetric method was employed as a tool to determine the proximate analysis data of biomass samples through TG and DTG curves, which were generated by tracking changes in biomass mass loss over time or temperature. NIRS non−destructively scanned the chipped biomass in diffuse reflectance while ground biomass using transflectance mode, covering the wavenumber range of 3594.87 to 12,489.48 cm−1. The PLSR−based models: Full−PLSR, genetic algorithm (GA)−PLSR, successive projection algorithm (SPA)−PLSR, the spectral multi−preprocessing (MP) PLSR− 5 range method, and the MP PLSR−3 range method were developed. Model performance was assessed, compared, and selected based on the coefficient of determination in the prediction set (R2P), root mean square error in the validation set (RMSEP), and the ratio of prediction to deviation (RPD). Based on the comprehensive analysis of model performance, MC and FC models of chip biomass have demonstrated satisfactory performance which makes it applicable cautiously in any application, including research. The optimum models for MC and FC in chip biomass were constructed using GA−PLSR with 2nd derivative and Full−PLSR with a constant offset, resulting in R2P values of 0.8654 and 0.8773, RMSEP values of 0.85% and 2.12%, and RPD values of 2.9 and 3.0, respectively. Other parameters such as MC and FC in ground biomass as well as VM and ash content in both chip and ground biomass were found suitable for rough screening. The sensitivity of the selected model was assessed by calculating the limit of quantification (LOQ), and the results indicated that the calculated LOQ values for VM in both chip and ground biomass and FC in chip biomass are lower than the minimum reference values used during model development, signifying a high level of sensitivity. However, for the remaining parameters, the LOQ values surpass the established minimum reference value, suggesting the model could not predict the future samples with reference value lower than the calibration range. Nevertheless, enhancing the models by incorporation an ample number of representative biomass samples and consistently validating the models with unknown samples is imperative to ensure accurate predictions.

This study explores the correlation between payment statistics and sector-wise Gross Value Added (GVA) in the Indian economy from 2011 to 2022, assessing the importance of payment and settlement systems. Through regression analysis, the impact of payment statistics on GVA across diverse sectors is assessed. The results indicate that, during the specified period, payment statistics exhibit a significant influence on sector-wise GVA. These findings underscore the pivotal role of payment and settlement systems in the Indian financial landscape.

Rice canopy height and density are directly usable crop phenotypic traits for the direct estimation of crop biomass. Therefore, it is crucial to rapidly and accurately estimate rice canopy phenotypic parameters. To achieve non-destructive detection and estimation of essential phenotypic parameters in rice, a platform based on LiDAR point cloud data for rice phenotypic parameter detection was established. Data collection of rice canopy layers was performed across multiple plots. The LiDAR-detected canopy top point clouds were selected using a method based on the highest percentile, and the rice canopy surface model was calculated. Canopy height estimation was the difference between ground elevation and percentile value. To determine the optimal percentile defining the rice canopy top, testing was conducted incrementally from 0.8 to 1 with an increment of 0.005. The optimal percentile value was found to be 0.975. The root mean square error (RMSE) between LiDAR-detected canopy height and manually measured canopy height was calculated. The prediction model based on canopy height (R2=0.941, RMSE=0.019) exhibited a strong correlation with actual canopy height. Linear regression analysis was conducted between gap fraction of different plots and manually detected average Leaf Area Index (LAI) of rice canopy. Prediction models for canopy LAI based on ground return counts (R2=0.24, RMSE=0.1) and ground return intensity (R2=0.28, RMSE=0.09) showed strong correlations but had lower correlation with rice canopy LAI. Regression analysis was performed between LiDAR-detected canopy height and manually measured rice canopy LAI. The results indicated that the prediction model based on canopy height (R2=0.77, RMSE=0.03) was more accurate.

With the intensification of population aging in rural areas, it becomes increasingly important to analyze the post-retirement migration intention of rural residents and the variables influencing these intentions. In this study, we focus on rural residents aged 45 to 60 and investigate the main variables that influence the post-retirement migration intention of rural residents, using survey data collected from 164 households in three different rural areas and the logistic regression model. From the result of this study, we found that gender, part-time employment, savings level, children's residence and occupation stability, and interest in urban living positively affect migration intention. In contrast, the number of rural companions, relationships with others in rural areas, and evaluation of rural living have a negative effect. In addition, we employ age and the proportion of mobile income as control variables to examine the variables that influence the post-retirement migration intention in different age groups and mobile income groups. The analysis reveals that, the variables influencing post-retirement migration intention varied across age groups and mobile income groups, and this variation can be attributed to the differences between groups' characteristics.

A self-protective metal/ liquid microcapsule composite plating coating has been prepared in our previous research. The release speed of liquid core material from microcapsules is crucial for the coating surface properties. The aim of this paper is to study the permeability rule of liquid microcapsules within composite coatings. According to permeability experimental data’s linear characteristics, multiple linear regression is firstly used to set up permeability model of liquid microcapsules. The results show that a reliable mathematical model about membrane porosity, viscosity of core material and membrane thickness is established under ambient temperature and moisture. Meanwhile, the predictive capacity and reliability of this model are analyzed carefully.

The cumulative nature of knowledge in science in general and for social science in particular depends on research being conducted with integrity, with fraudulent research being one of the most harmful of questionable research practices. It has been observed that, in fabricated research, there is often a deficit of zeroes in the last digits of regression results. In research, authored by Dr. Eric A. Stewart, that has been retracted, there appears to have been a paucity of zeroes as last digits in his regression results. Eight hypotheses were tested to re-examine the relative lack of zeroes and possible increases in ones or nines as last digits. Some support was found for all hypotheses. It appears that in Stewart’s retracted research, ones and nines were substituted for zeroes as last digits. Furthermore, the increased proportions of ones and nines was found to be highly correlated with other anomalies in the same retracted articles, possibly indicative of fabrication of the results in the retracted articles. Further research in this area might use symbolic interaction theory or justification theory to guide our developing knowledge about this type of questionable research practice.

Shallow landslides pose serious threats to human existence and economic development, especially in the Himalayan areas. Landslide susceptibility mapping (LSM) is a proven way for minimizing the hazard and risk of landslides. Modeling as an essential step, various algorithms have been applied to LSM. In this study, information value (IV) and logistic regression (LR) were selected as representatives of the conventional algorithms, categorical boosting (CatBoost) and conventional neural networks (CNN) as the advanced algorithms, for LSM in Yadong county, and their performance was compared. To begin with, 496 historical landslide events were compiled into a landslide inventory map, followed by a list of 11 conditioning factors, forming a data set. Secondly, the data set was randomly divided into two parts, 80% of which was used for modeling and 20% for validation. Finally, the area under the curve (AUC) and statistical metrics were applied to validate and compare the performance of the models. The results showed that the CNN model performed the best (AUC 0.974 and accuracy=93.3%), while the LR model performed the worst (AUC 0.974 and accuracy=93.3%) and CatBoost model performed better (AUC 0.974 and accuracy=93.3%). Besides, the LSM constructed by the CNN model did a more reasonable prediction of the distribution of susceptible areas. As for feature selection, did a more detailed analysis of conditioning factors but the results were uncertain. The result analyzed by GI may be more reliable but fluctuates with the amount of data. The conclusion reveals that the accuracy of LSM can be further improved with the advancement of algorithms, by determining more representative features, which serve as a more effective guide for land use planning in the study area or other highlands where landslides are frequent.

Winter frost injury is a major limiting factor for olive cultivation in temperate regions. The response of olive shoots to freezing stress can be used for selecting resistant genotypes to freezing. The electrolyte leakage (EL) and tetrazolium tests (TZ) are commonly used to evaluate dead tissues in cold stress studies. The temperature-response curve of dead tissues to lethal temperature (LT) is measured with models to calculate LT50 and LT90. In this study, we evaluated the accuracy and efficiency of eighteen non-linear regression models (NLRs) in calculating LT50 and LT90 of freezing stress in different olive cultivars at various stages of dormancy. After evaluating the prediction performance of NLR models, it was found that only eight models were suitable for the purpose of this research out of the 18 models examined. The 2p-logistic and Gompertz models were selected for modeling EL and TZ, respectively. Our research findings indicate that the Roughani, Kawi, and Zard varieties of olive trees exhibit the best performance in cold weather conditions. Our findings provide valuable insights into selecting frost-resistant cultivars and designing effective strategies for cold acclimation in olive cultivation.

Quantile regression model is widely used in variable relationship research of general size data, due to strong robustness and more comprehensive description of the response variables' characteristics. With the increase of data size and data dimension, there have been some studies on high-dimensional quantile regression under the classical statistical framework, including higher-efficient frequency perspective, which is however at cost of randomness quantification, or lower-efficient Bayesian method based on MCMC sampling. To overcome these problems, we propose the high-dimensional quantile regression with Spike-and-Slab Lasso penalty based on variational Bayesian (VBSSLQR), which can not only improve the computational efficiency but also measure the randomness via variational distributions. The simulation studies and real data analysis illustrate that the proposed VBSSLQR method is superior to or equivalent to other quantile and non-quantile regression methods (including Bayesian and non-Bayesian methods), and its efficiency is higher than any other method.

Water is an essential commodity to sustain life. The condition of water in Tiruchirappalli was measured using different Physicochemical parameters like Temperature, pH, TDS, Total Solids, Salinity, Total Hardness, and Electrical Conductivity. Water samples were collected from different places in Tiruchirappalli city, Tamil Nadu. Water samples were examined by different chemical methods. According to the results, Thiruvarambur-1 showed comparatively higher results in the case of every parameter compared to other sampling stations. Obtained results were further interpreted using statistical tools. Considering ECs as a principal component for the regression and correlation analysis with other parameters significant correlation was found. A strong correlation was observed between ECs and TDS, Total Hardness, Turbidity, and Salinity.

Machine learning forks into three main branches such as supervised learning, unsupervised learning, and reinforcement learning where reinforcement learning is much potential to artificial intelligence (AI) applications because it solves real problems by progressive process in which possible solutions are improved and finetuned continuously. The progressive approach, which reflects ability of adaptation, is appropriate to the real world where most events occur and change continuously and unexpectedly. Moreover, data is getting too huge for supervised learning and unsupervised learning to draw valuable knowledge from such huge data at one time. Bayesian optimization (BO) models an optimization problem as a probabilistic form called surrogate model and then directly maximizes an acquisition function created from such surrogate model in order to maximize implicitly and indirectly the target function for finding out solution of the optimization problem. A popular surrogate model is Gaussian process regression model. The process of maximizing acquisition function is based on updating posterior probability of surrogate model repeatedly, which is improved after every iteration. Taking advantages of acquisition function or utility function is also common in decision theory but the semantic meaning behind BO is that BO solves problems by progressive and adaptive approach via updating surrogate model from a small piece of data at each time, according to ideology of reinforcement learning. Undoubtedly, BO is a reinforcement learning algorithm with many potential applications and thus it is surveyed in this research with attention to its mathematical ideas. Moreover, the solution of optimization problem is important to not only applied mathematics but also AI.

Despite a rapid rise in NBS development in recent years, the methods for evaluating NBS still have certain gaps. We propose an approach based on a combination of remote sensing data and meteorological variables to reconstruct the spatio-temporal variation of net ecosystem exchange from eddy-covariance stations. Lagrangian particle dispersion model was used for upscaling of satellite images and flux towers. We trained data-driven models based on kernel methods separately for each selected land cover class. The results suggest that the proposed approach to quantifying carbon exchange on a medium-to-large scale by blending eddy covariance flux data with moderate resolution satellite and weather data provides a set of key advantages over previously deployed methods: (1) scalability, achieved via the validation design based on a separate set of eddy covariance stations; (2) high spatial and temporal resolution due to use of the Landsat imagery; (3) robust and accurate predictions due to improved data quality control, advanced machine learning techniques, and rigorous validation. The machine learning models yielded high cross-validation results. Overall we present here globally scaled technology for the land sector based on high resolution remote sensing imagery, meteorological variables, and direct carbon flux measurements of eddy covariance flux stations.

The efficacy of predicting geochemical parameters with a 2-chain workflow using spectral data as the initial input is evaluated. Spectral measurements spanning the approximate 400-25000nm spectral range are used to train a workflow consisting of a non-negative matrix function (NMF) step, for data reduction, and a random forest regression (RFR) to predict 8 geochemical parameters. Approximately 175000 spectra with their corresponding chemical analysis were available for training, testing and validation purposes. The samples and their spectral and chemical parameters represent 9399 drillcore. Of those, approximately 20000 spectra and their accompanying analysis were used for training and 5000 for model validation. The remaining pairwise data (150000 samples) were used for testing of the method. The data are distributed over 2 large spatial extents (980 km2 and 3025 km2 respectively) and allowed the proposed method to be tested against samples that are spatially distant from the initial training points. Global R2 scores and wt.% RMSE on the 150000 validation samples are Fe(0.95/3.01), SiO2(0.96/3.77), Al2O3(0.92/1.27), TiO(0.68/0.13), CaO(0.89/0.41), MgO(0.87/0.35), K2O(0.65/0.21) and LOI(0.90/1.14), given as Parameter(R2/RMSE), and demonstrate that the proposed method is capable of predicting the 8 parameters and is stable enough, in the environment tested, to extend beyond the training sets initial spatial location.

Neural networks models are mostly represented by oriented graphs where only the components, constitutive elements of the graph, are transcribed into mathematical xpression. Indeed, accurate knowledge of the full expression of the model is required in certain situations such as selecting among several reference models, the one that best fits the available data or comparing the explanatory and predictive performance of an established model with respect to some reference models. In this paper, we establish a formalism of the mathematical expression for multilayer perceptron neural network in a general framework, MLP-p-n-q, with p, n and q natural integers and show its restriction to cases where one has a hidden layer and multivariate outputs (MLP-p-1-q), and then a single output (MLP-p-1-1). Then, we give some specific cases of the most commonly used models. An application case is presented in the context of solving a nonlinear regression problem.

Missing observations constitute one of the most important issues in data analysis in applied research studies. The magnitude and their structure impact parameters estimation in the modeling with important consequences for decision-making. This study aims to evaluate the efficiency of imputation methods combined with the backpropagation algorithm in a nonlinear regression context. The evaluation is conducted through a simulation study including sample sizes (50, 100, 200, 300 and 400) with different missing data rates (10, 20, 30 40 and 50%) and three missingness mechanisms (MCAR, MAR and MNAR). Four imputation methods (Last Observation Carried Forward, Random Forest, Amelia and MICE) were used to impute datasets before making prediction with backpropagation. 3-MLP model was used by varying the activation functions (Logistic-Linear, Logistic-Exponential, TanH-Linear and TanH-Exponentiel), the number of nodes in the hidden layer (3 - 15) and the learning rate (20 - 70%). Analysis of the performance criteria (R2, r and RMSE) of the network revealed good performances when it is trained with TanH-Linear functions, 11 nodes in the hidden layer and a learning rate of 50%. MICE and Random Forest were the most appropriate for data imputation. These methods can support up to 50% of missing rate with an optimal sample size of 200.

Within the framework of multiblock data analysis, a unified approach of supervised methods is discussed. It encompasses multiblock redundancy analysis (MB-RA) and multiblock partial least squares (MB-PLS) regression. Moreover, we develop new supervised strategies of multiblock data analysis, which can be seen as variants of one or the other of these two methods. They are respectively refered to as multiblock weighted redundancy analysis (MB-WRA) and multiblock weighted covariate analysis (MB-WCov). The four methods are based on the determination of latent variables associated with the various blocks of variables. They are derived from clear optimization criteria whose aim is to maximize either the sum of the covariances or the sum of squared covariances between the latent variable associated with the response block of variables and the block latent variables associated with the various explanatory blocks of variables. We also propose indices to help better interpreting the outcomes of the analyses. The methods are illustrated and compared based on simulated and real datasets.

Spatial evaluation of flood-prone areas at the drainage basins is one of the basic strategies in the field of flood risk management. The present study aims to investigate the efficiency of the CN logistic and hydrological regression model for predicting and zoning floods. In the first stage, 13 runoff parameters, hydrologic soil groups (HSGs), slope, lithology, drainage density (DD), land curvature, elevation, distance to waterways/rivers, topographic wetness index (TWI), stream power index (SPI), rainfall, land use, and NDVI were employed. In the SCS-CN model of the drainage basin, the infiltration rate (S) and runoff amount (Q) were determined. The weights of the used layers were weighted by the AHP. Also, a flood zoning map of the drainage basin with different 5, 15, 25, and 50 year return periods was drawn by applying the weights of the layers. To ensure the accuracy of the zoning map with the logistic regression model, the ROC curve, and the area below the curve were used. The results showed that for the prediction rate, the AUC is 0.81%, indicating that the model has acceptable accuracy. The most important factors affecting flood are geological index; distance to waterways/rivers; and NDVI in the logistic regression model, and slope, DD, rainfall, and land use in the SCS-CN model respectively. 30 to 46% of the drainage basin area during 5 to 50 year periods has moderate flood potential, and 28 to 34% has high potential.

In this report the positive cases of Covid19 in India with effect from 7th September ,2020 to 25th October ,2020 are analysed for statistical relevance . The scattered data are used to find out a model equation correlating two variables number of recovered Covid –patient with an interval of regular seven days . The best fit regression analysis shows a significant correlation of Pearson coefficient (r) with standard error ( s ) with a probable lower mortality rate . Finally the limitations of this analysis is discussed herewith .

The paper presents an assessment of the growth dynamics of the modal fir plantations in the Lower Angara region. At present, a vast area of fir forests in the Lower Angara region is characterised by a significant decrease in sustainability due to periodic forest fires, insect pests outbreaks and diseases, which lead to their natural degradation and death. However, the intensity of coniferous stand growth in certain forest site characteristics persists in the long term. Therefore, creating regression models of forest growth and development involving the identification of site conditions is very important both from a practical point of view and for environmental monitoring. The materials of the mass inventory of 3491 stands served as the initial data for studying the processes of fir plantations natural growth. The Hoerl Model function is suitable for the best approximation of stand growth since it is characterised by high levelling factor (from 0.970 to 0.987) and a small standard error (not exceeding 7%). As a result of the research, there have been constructed sketches of the growth rate tables for the modal Siberian fir stands of the third bonitet class of the forb and mossy groups of forest types.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

This article explores the impact of farmers’ vocational training on their income. Survey data concerning agricultural product quality and agricultural product sales were collected by the research team in Yantai City, China. An endogenous transformation regression model (ESR) was then used to analyze the impact of training on farmers’ family income, and the income mechanism was further tested. The results from the empirical analysis suggest that (1) Participating in training can significantly increase farmers’ income; (2) Farmers who pay more attention to the quality of their agricultural products during the production process are more likely to see their incomes increase after participating in the training.

Background: There are major air pollution monitoring gaps in sub-Saharan Africa. Developing capacity in the region to conduct air monitoring in the region can help estimate exposure to air pollution for epidemiology research. The purpose of our study is to develop a land use regression (LUR) model using low-cost air quality sensors developed by a research group in Uganda (AirQo). Methods: Using these low-cost sensors, we collected continuous measurements of fine particulate matter (PM2.5) between May 1, 2019 and February 29, 2020 at 22 monitoring sites across urban municipalities of Uganda. We compared average monthly PM2.5 concentrations from the AirQo sensors with measurements from a BAM-1020 reference monitor operated at the US Embassy in Kampala. Monthly PM2.5 concentrations were used for LUR modeling. We used eight Machine Learning (ML) algorithms and ensemble modeling; using 10-fold cross validation and root mean squared error (RMSE) to evaluate model performance. Results: Monthly PM2.5 concentration was 60.2 µg/m³ (IQR: 45.4-73.0 µg/m³; median= 57.5 µg/m³). For the ML LUR models, RMSE values ranged between 5.43 µg/m³ - 15.43 µg/m³ and explained between 28% and 92% of monthly PM2.5 variability. Generalized additive models explained the largest amount of PM2.5 variability (R²=0.92) and produced the lowest RMSE (5.43 µg/m³) in the held-out test set. The most important predictors of monthly PM2.5 concentrations included monthly precipitation, major roadway density, population density, latitude, greenness, and percentage of households using solid fuels. Conclusion: To our knowledge, ours is the first study to model the spatial distribution of urban air pollution in sub-Saharan Africa using air monitors developed from the region itself. Non-parametric ML for LUR modeling performed with high accuracy for prediction of monthly PM2.5 levels. Our analysis suggests that locally produced low-cost air quality sensors can help build capacity to conduct air pollution epidemiology research in the region.

COVID-19 pandemic that started in China has spread within 3 months to the entire globe. We tested the hypothesis that the vaccination against tuberculosis by BCG correlates with a better outcome for COVID-19 patients. Our analysis covers 55 countries complying with predetermined thresholds on the population size and number of deaths per million (DPM). We found a strong negative correlation between the years of BCG administration and the DPM along with the progress of the pandemic, corroborated by permutation tests. The results from multivariable regression tests with 23 economic, demographic, health-related, and pandemic restriction quantitative properties, substantiate the dominant contribution of BCG years to the COVID-19 outcomes. The analysis of countries according to an age-group partition reveals that the strongest correlation is attributed to the coverage in BCG vaccination of the young population (0-24 years). Furthermore, a strong correlation and statistical significance are associated with the degree of BCG coverage for the most recent 15 years, but no association was observed in these years for other broadly used vaccination protocols for measles and rubella. We propose that BCG immunization coverage, especially among the most recently vaccinated contributes to attenuation of the spread and severity of the COVID-19 pandemic.

The constant news about the corona virus is scary. It is not possible to separate treatment for Cancer due to COVID-19. An effective treatment comparison strategy is needed. We need to have a handy tool to understand cancer progression in this unprecedented scenario. Linking different events of cancer progression is the need of the hour. It is a methodological challenge. We provide the solutions to overcome the issue with interval between two consecutive events in motivating head and neck cancer (HNC) data.

Market channel choice makes important contributions to the incomes and other livelihood attributes among smallholder farmers in developing countries. Often considered from a number of perspectives, the dominant view articulated suggests an advantageous integration into formal market channels. This position is questioned as it has implications for smallholder farmers’ food security and rural incomes. Using a mixed methods approach, the study collected primary data from 174 smallholder farmers and applied both a descriptive and multinomial logit regression model to analyze factors contributing to cocoyam production and market channel choices among respondents in the study area. Findings indicate that financial returns and available markets were key factors in cocoyam production, while amount received was a driver of market channel choice among 89% of respondents who sold directly at farm-gate. Farmers’ age (p=0.044), household size (p=0.043), distance to market (p=0.021), additional income (p=0.017) and amount received (p=0.014) were significant variables (p<.05) in the determinants of market channel choice. The study recommended improving market information provision and strengthening farmer associations which will enable smallholder farmers in rural communities to make informed choices with respect to produce price, access other markets and consolidate their collective market bargaining position.

This paper proposes a model based on gene expression programming for predicting discharge coefficient of triangular labyrinth weirs. The parameters influencing discharge coefficient prediction were first examined and presented as crest height ratio to the head over the crest of the weir (p/y), crest length of water to channel width (L/W), crest length of water to the head over the crest of the weir (L/y), Froude number (F=V/√(gy)) and vertex angle () dimensionless parameters. Different models were then presented using sensitivity analysis in order to examine each of the dimensionless parameters presented in this study. In addition, an equation was presented through the use of nonlinear regression (NLR) for the purpose of comparison with GEP. The results of the studies conducted by using different statistical indexes indicated that GEP is more capable than NLR. This is to the extent that GEP predicts the discharge coefficient with an average relative error of approximately 2.5% in such a manner that the predicted values have less than 5% relative error in the worst model.

On October 18, 2017, Chinese President Xi Jinping presented the blueprint for building a modernized socialist nation through the realization of the Xiao Kang (Every nation enjoys a peaceful and affluent life, it is meaningless to eliminate the poor) social construction at the 19th Congress of China. Subsequent to the 2008 financial crisis, the world has moved on to the new economic status of the New Normal. China has also entered the era of “Xinchang Thai,” which is moving from the high-growth to the moderate-growth phase. Therefore, the government of China emphasizes privatization, liberalization, and deregulation. China is also influenced by government policies due to the nature of socialism. This study confirms China’s current stage of economic development based on Barro’s theory. Thus, we use a quantile regression model and examine the correlation between economic growth and functional classification of government expenditure during Xi Jinping's term of office. Furthermore, we selected Korea as a comparative country as the two countries have common features.

Many scientific and technological problems are studied with the help of computer codes that simulate the phenomena of interest rather than via traditional laboratory experiments. Such models play an important role in neuroscience where they are used to mimic brain function from the sub-cellular to the macroscopic level. Exploration with computer models carries with it a number of statistical challenges: where to sample the input space for the simulator, how to make sense of the data that is generated, how to estimate unknown parameters in the model, how to validate a model. The simulator setting also has some unique problems and possibilities. This review paper describes statistical research on these issues and how that work might be applied to neural simulations.

Modern portfolio theory claims that diversification into non-correlated or negatively correlated activities reduces the overall risk of a portfolio. Considering the total income of a bank as a portfolio of interest income and non-interest income, this paper investigates how the variability of interest income and non- interest income, and covariance between interest income and non-interest income influence the various risk factors of banks. We set out a study in the Indian context. We have extracted data for the period 2005-2017 and employed an extended version of Ridge, Lasso and Elastics Net regression to take care of multi-collinearly in our data. We have considered 10-fold cross-validation techniques to get optimal values of tuning parameters for Ridge, Lasso, and Elastics Net regression (which is a convex combination of ridge and the LASSO). We have compared different regression techniques by comparing RMSE and R2. We observe that non-interest income is positively correlated with interest income in the Indian context, but it does stabilize variance, idiosyncratic risk & market risk (Beta) of Indian Banks.

Text fields in electronic medical records (EMR) contain information on important factors that influence health outcomes, however, they are underutilized in clinical decision making due to their unstructured nature. We analyzed 6,497 inpatient surgical cases with 719,308 free text notes from Le Bonheur Children’s Hospital EMR. We used a text mining approach on preoperative notes to obtain the text-based risk score algorithm as predictive of death within 30 days of surgery. We studied the additional performance obtained by including text-based risk score as a predictor of death along with other structured data based clinical risk factors. The C-statistic of a logistic regression model with 5-fold cross-validation significantly improved from 0.76 to 0.92 when text-based risk scores were included in addition to structured data. We conclude that preoperative free text notes in EMR include significant information that can predict adverse surgery outcomes.

Technology development changes society and society demands new and innovative technology development. We analyze technology to understand society and technology itself. Many researches have been introduced in various fields. Most of them were about patent analysis. This is because detailed and accurate results of research and development are patented. In this paper, we study on new patent analysis method based on count data model and Bayesian regression analysis. Using count data model, we analyze the technological keywords extracted from the collected patent documents. We use the posterior distribution of Bayesian statistics to reflect the experience and knowledge of the relevant technological experts in the analysis model. Moreover, we apply the proposed model to finding sustainable technologies. Finding and developing sustainable technologies is an important activity for companies and research institutes to maintain their technological competitiveness. To illustrate how our modeling could be applied to real domain, we carry out a case study using the patent documents related to artificial intelligence.

The chain ladder method is a popular technique to estimate the future reserves needed to handle claims that are not fully settled. Since the predictions of the aggregate portfolio (consisting of different subportfolios) in general differ from the sum of the predictions of the subportfolios, a general multivariate chain ladder (GMCL) method has already been proposed. However, the GMCL method is based on the seemingly unrelated regression (SUR) technique which makes it very sensitive to outliers. To address this issue a robust alternative is introduced which estimates the SUR parameters in a more outlier resistant way. With the robust methodology it is possible to detect which claims have an abnormally large influence on the reserve estimates. We introduce a simulation design to generate artificial multivariate run-off triangles based on the GMCL model and illustrate the importance of taking into account contemporaneous correlations and structural connections between the run-off triangles. By adding contamination to these artificial datasets, the sensitivity of the traditional GMCL method and the good performance of the robust GMCL method is shown. From the analysis of a portfolio from practice it is clear that the robust GMCL method can provide better insight in the structure of the data.

This paper has three objectives, the first is to present a detailed overview in the form of a tutorial for the developments of several key quantile time series modelling approaches. The second objective is to develop a general framework to represent such quantile models in a unifying manner in order to easily develop extensions and connections between existing models that can then be developed to further extend these models in practice. In this regard, the core theme of the paper is to provide perspectives to a general audience of core components that go into construction of a quantile time series model and then to explore each of these core components in detail. The paper is not addressing the concerns of estimation of these models, as there is existing literature on these aspects in many settings, we provide references to relevant works on these aspects in several classes of model. Instead, the focus is rather to provide a unified framework to construct such models for practitioners, therefore the focus is instead on the properties of the models and links between such models from a constructive perspective. The third objective is to compare and discuss the application of the different quantile time series models on several sets of interesting demographic and mortality based time series data sets of relevance to life insurance analysis. The exploration included detailed mortality, fertility, births and morbidity data in several countries with more detailed analysis of regional data in England, Wales and Scotland.

Various factors and constraints should be considered when developing a manufacturing production schedule, and such a schedule is often based on rules. This paper develops a composite dispatching rule based on heuristic rules that comprehensively consider various factors in a semiconductor production line. The composite rule is obtained by exploring various states of a semiconductor production line (machine status, queue size, etc.), where such indicators as makespan and equipment efficiency are used to judge performance. A model of the response surface, as a function of key variables, is then developed to find the optimized parameters of a composite rule for various production states. Further, dynamic scheduling of semiconductor manufacturing is studied based on support vector regression (SVR). This approach dynamically obtains a composite dispatching rule (i.e. parameters of the composite dispatching rule) that can be used to optimize production performance according to real-time production line state. Following optimization, the proposed dynamic scheduling approach is tested in a real semiconductor production line to validate the effectiveness of the proposed composite rule set.

Global change is affecting vegetation cover and processes through multiple pathways. Long time series of surface land surface properties derived from satellite remote sensing offer a unique abilities to observe these changes, particularly in areas with complex topography and limited research infrastructure. Here, we focus on Nepal, a biodiversity hotspot where vegetation productivity is limited by moisture availability (dominated by a summer monsoon) at lower elevations and by temperature at high elevations. We analyze normalized difference vegetation index (NDVI) from 1981 to 2015 semimonthly, at 8 km spatial resolution. We use a random forest (RF) of regression trees to generate a statistical model of NDVI as a function of elevation, land use, CO2 level, temperature, and precipitation. We find that NDVI has increased over the studied period, particularly at low and middle elevations and during fall (post-monsoon). We infer from the fitted RF model that the NDVI linear trend is primarily due to CO2 level (or another environmental parameter that is changing quasi-linearly), and not primarily to temperature or precipitation trends. On the other hand, interannual fluctuation in NDVI is more correlated with temperature and precipitation. RF accurately fits the available data and shows promise for estimating trends and testing hypotheses about their causes.

There is a growing concern about climate change being a serious threat to insurance business sustainability. Knowing if climate warming is a cause for claims and losses increase, and how this cause-effect relationship will develop in the future are two open major questions. In this article, we answer both questions by particularizing the geographical area of Spain, and a precise risk, hailstorm in crop insurance in the line of business of wine grapes. We measure climate change thanks to the Spanish Actuarial Climate Index (SACI). We use a database containing all the claims caused by hail risk in Spain from 1990 to 2022. With homogenized data, we consider as dependent variables the monthly number of claims, monthly number of loss costs equal to one, and monthly total losses. The independent variable is the monthly Spanish Actuarial Climate Index (SACI). We try to explain the former through the latter using regression and quantile regression models. Our main finding is that climate change as measured by SACI explains these three dependent variables. We also give an estimation of the increase of the monthly total losses Value at Risk, corresponding to a future increase in climate change measured in units of SACI. Spanish crop insurance managers should carefully incorporate these conclusions into their decision-making process to keep this line of business sustainable in the future.

The paper provides a methodological framework based on Multiple Criteria Decision Aid methods for determining relative regional vulnerabilities associated with forest fires that occurred during a given period. Different notions of ex-post vulnerability are defined based on the forest area burned and the frequency of forest fires, and their relation to the regions’ area and several socioeconomic characteristics. The methodology is applied to Greece and its administrative regions for the period 2000–2022. Linking the forest fire events with summer and spring temperatures and precipitation and using econometric count data analysis, the paper explores the climatic drivers of forest fire occurrence and provides projections of the expected change in the frequency of fires of specific size classes conditional on the evolution of mean seasonal regional temperature and precipitation according to IPCC scenarios. The results regarding relative regional vulnerabilities and expected forest fires could be useful in designing policies for preserving forests as natural capital and promoting sustainability.

Human activities (e.g., exploitation, utilization, and conservation) exert substantial impact on forest ecological functions (FEF). The human influence on FEF significantly varies across developmental stages, which are attributed to the temporal and spatial in nature. This study evaluates some notable FEF indices (FEFI) in the 448 counties within the Yellow River basin (YRB) using panel data from the Seventh to Ninth National Forest Inventory. Data analysis involves employing the residual trends, geographical and temporal weighted regression. Results indicate that, firstly, the overall forest ecological function in the YRB is moderate to inferior, with superior FEF in counties endowed with more natural forest resources. Afforestation demonstrates a short-term improvement, but its effectiveness diminishes over time. Secondly, the positive spatial correlation is stronger among counties, characterized by both high-high and low-low agglomeration effects. Scattered planting, simple stand structure, and concentrated harvesting of forests at the identical stand ages hinder the formation of complex and large-scale FEF agglomerations. Thirdly, significant spatial-temporal differences exist in the impact of human activities on FEF. In the upper reaches of the basin, increased vegetation coverage through agricultural and forestry production benefited FEF, however, some over-exploitation of forests and grasslands is observed there. In the middle reaches, the economic development, expanding population and the greening activities help to improve FEF effectively, but excessive water using in agricultural production brought more difficulties to FEF improvement. In the lower reaches of the basin, improved wastelands and forest protection positively influence FEF. This study recommends that county governments should prioritize forest management with multi-species and multi-layered complex forests. Each county should define its position in regional development and ecological protection, considering the potential impacts on neighboring regions. This holistic approach promotes more effective integrated regional management.

Nepal, primarily an agricultural country, heavily relies on agricultural residue and fuelwood for daily energy requirements. In 2022, total energy consumption was 640 PJ, with traditional sources accounting for 64.17%, and fuelwood comprising 58.53% of total fuel consumption. The estimated potential supply of agricultural residue is 26 million tonnes, yielding about 442 million GJ of energy in 2021. Biomass trading often emphasizes volume or weight, necessitating a rapid and non-destructive assessment of energy properties for mutual benefit, aiding in the identification, management, and utilization of biomass sources. In this study, 200 biomass samples were collected in two batches (126 and 74 samples) from various locations in Nepal. Using Partial Least Squares Regression (PLSR), a model was developed correlating higher heating value (HHV) from a bomb calorimeter and spectral data from Fourier Transform near-infrared spectroscopy (FT-NIRS) (3595 – 12,489 cm-1) sensor. PLSR models incorporated raw spectra, eight preprocessing techniques, the multi-preprocessing five-range method, and a genetic algorithm. Outliers in the first batch were identified, and the first batch divided into an 80% calibration set and a 20% validation set, while the second batch was designated as an unknown sample set. The optimum PLSR model, utilizing first derivative preprocessing, improved accuracy by 6.77%, with coefficients of determination in the calibration set, validation set, and unknown set as 0.9694, 0.9578, and 0.8089, respectively. Root mean square errors were 132.4790 J/g, 189.4800 J/g, and 360.8845 J/g for the calibration set (RMSEC), validation set (RMSEP), and unknown set (RMSEUN), respectively. The prediction to deviation ratio (RPD) for the validation set and unknown set was 4.9 and 2.4, respectively. The cross validation model of combined sample data of every sets showed the R2CV of 0.95 and RPDCV of 4.6 indicating the model could serve as a reliable and swift non-destructive alternative for evaluating biomass HHV using NIRS and ready for updating for industrial use. However, incorporating a larger number of representative samples is crucial to enhance accuracy and develop a more comprehensive global model for predicting biomass HHV.

With the use of linear regression modeling, this study sought to forecast and analyze rainfall patterns in Ethiopia. The dataset included historical rainfall data as well as pertinent independent variables. The R-squared score and mean squared error (MSE) were used to assess the effectiveness of the linear regression model. The results showed that the model's ability to forecast and analyze rainfall patterns was not very good. Only around 5.3% of the variance in rainfall could be explained by the chosen independent variables, according to the R-squared score of 0.053. This low number indicated that there was little correlation between the selected variables and rainfall, and that a sizable percentage of the variation in the dependent variable was not captured by the model. The model's accuracy in forecasting rainfall was shown to be quite low by the MSE error, with significant squared discrepancies between the expected and actual amounts. These results support the notion that the linear regression model as it is now designed is not appropriate for studying or forecasting Ethiopia's rainfall patterns. Alternative modeling approaches, the inclusion of other pertinent factors, and the assurance of the availability of high-quality data that faithfully captures the intricate dynamics of rainfall in the area all require more investigation.

The research presented in this paper examines a new proposed approach for identifying safety improvement sites on rural highways. Unlike conventional approaches, the proposed approach does not require crash history, but rather utilizes classified variables for traffic volume, geometric features, and roadside characteristics that do not require access to exact data or extensive technical expertise. The research validates the performance of the proposed approach using field data from a large sample of rural two-lane highway segments in the state of Oregon including traffic, roadway, and crash data. Using observed crash history as a reference, the performance of the proposed ap-proach was compared to two of the well-established methods in practice, namely: the Empirical Bayes (EB) and the Potential for Safety Improvement (PSI) methods. The study results suggest that, using crash density for highway segments, the performance of the proposed method was lower than that of the EB and PSI methods. This is despite the high R-square value of the predictive model used in the proposed method. However, when using crash frequencies for highway segments, the per-formance of the proposed method was found comparable to the well-established EB and PSI methods.

This study investigates the suitability of the timestamp approach algorithm for predicting blood pressure (BP) using wearable and comfortable devices, showcasing its accuracy even with low-frequency sampled signals. Developed within the SINTEC European project, the algorithm utilizes Electrocardiogram (ECG) and Photoplethysmogram (PPG) sensors, demonstrating promising results in both laboratory and hospital settings. The research emphasizes the algorithm’s potential to transform continuous and non-invasive BP monitoring through wearable technology, offering frequent measurements with minimal discomfort. While the study shows promise, further exploration is needed, focusing on optimizing machine learning coefficients for long-term monitoring applications and addressing potential changes over time. Technological improvements, including the implementation of edge computing algorithms, hold the key to enhancing BP accuracy, denoising techniques, and integrating alarm systems for future wearable solutions. This study emphasizes the adaptability of the algorithm for diverse healthcare environments, paving the way for broader applications in convenient and reliable BP monitoring.

In order to enhance the comfort of cycling, it is imperative to investigate the effects of vibration on non-motorized bicycle riding from the perspectives of road characteristics and traffic features. Through an analysis of the mechanisms by which road and traffic conditions influence cycling vibrations, 13 influencing factors were identified. Subsequently, the non-motorized bicycle lanes in Wuhan city were selected as the subject of empirical research, where three-axis accelerometers attached to the rider's torso were employed to measure and categorize vibration comfort levels. The experimental road segments were found to exhibit comfort levels falling between slightly uncomfortable and relatively uncomfortable. Further analysis of the influencing factors was conducted using the Random Forest algorithm and Logistic Regression. The results revealed that six factors significantly impact the comfort of cycling: the presence of dedicated non-motorized bicycle lanes, the absence of physical separation between non-motorized and motorized traffic, cycling speed, the number of road surface irregularities, the presence of parking areas within the non-motorized bicycle lane, and the type of non-motorized bicycle. This study provides valuable insights into the factors affecting non-motorized bicycle lane usage and contributes to the refined design of urban non-motorized bicycle infrastructure, thereby facilitating better support for sustainable urban transportation.

Art organizations are increasingly focusing on enhancing the visitor experience to attract a wider audience. The aim objective of this study was to explore the key factors that influence the visitor experience of offline art exhibitions and to use a mixed methods to data collection and analysis. The research process was divided into three stages. In the first stage, we conducted semi-structured interviews with 12 respondents by dividing the exhibition experience into three time periods: pre, during, and post-visit. We extracted seven factors affecting visitor experience through qualitative content analysis including marketing, motivation, physical environment, exhibit quality, participation, technology and service facilities; in the second stage, we developed an assessment scale and pretested it; in the third stage, we collected 725 questionnaires to validate the factors of visitor experience in art exhibitions. The results of linear regression analyses showed that all seven key factors had a significant impact on visitor experience. This study constructed a scale to assess the factors of art exhibition experience, which provides theoretical sup-port for in-depth study of art exhibition experience and useful guidance for planning and design-ing art exhibitions to improve the quality of visitors' experience of art exhibitions.

In the pursuit of China’s dual carbon goals, identifying spatio-temporal changes in industrial carbon emission efficiency and their influencing factors in cities at different stages of development is the key to effective formulation of countermeasures to promote the low-carbon transformation of Chinese national industry and achieve high-quality economic development. In this study, we used balanced panel data of 270 Chinese cities from 2005 to 2020 as a research object: (1) to show spatio-temporal evolution patterns in urban industrial carbon emission efficiency; (2) to analyze the aggregation characteristics of industrial carbon emission efficiency in Chinese cities using Global Moran's I statistics; and (3) to use the hierarchical regression model for panel data to assess the non-linear impact of the digital economy on the industrial carbon emission efficiency of cities. The results show the following: (1) the industrial carbon emission efficiency of Chinese cities exhibited an upward trend from 2005 to 2020, with a spatial distribution pattern of high in the south and low in the north; (2) China's urban industrial carbon emission efficiency is characterized by significant spatial autocorrelation, with increasing and stabilizing correlation, and a relatively fixed pattern of spatial agglomeration; (3) there is a significant inverted-U-shaped relationship between the digital economy and the industrial carbon emission efficiency of cities. The digital economy increases carbon emissions and inhibits industrial carbon-emission efficiency in the early stages of development, but inhibits carbon emissions and promotes industrial carbon emission efficiency in mature developmental stages. Therefore, cities at all levels should reduce pollution and carbon emissions from high-energy-consuming and high-polluting enterprises, gradually reduce carbon-intensive industries, and accelerate the digital transformation and upgrading of enterprises. Western, central and eastern regions especially should seek to promote the sharing of innovation resources, strengthen exchanges and interactions relating to scientific and technological innovation, and jointly explore coordinated development routes for the digital economy.

As urban populations and transport demand expand, Pakistani metropolitan centers face traffic congestion and environmental challenges. This research aims to assess carpooling (CP) to alleviate traffic congestion, fuel demand, and pollution. This study was conducted in Islamabad, a fast-growing city with a high percentage of personal cars in Pakistan, to assess the travelers’ perceptions, and public acceptance of CP and determine the effects on traffic congestion, fuel consumption, and CO2 emissions. The investigation of travelers' perceptions towards CP was conducted through a stated preference questionnaire survey. A total of 700 responses from one million population of Islamabad were collected as per Sloven's Formula. SPSS and Smart PLS software were used for data analysis. Various factors influencing peoples’ travel perceptions, mode choice, and tendency to carpool, were categorized to evaluate the relationship between travelers’ perception and the tendency to carpool in the presence of mode choice as a mediating variable. Confirmatory factor analysis was conducted in SMART PLS to refine the number of scale items for each variable. One-way ANOVA, step-wise and mediated multiple regression analysis was conducted in SPSS to check the direct and mediating relationship between different variables. Moreover, the probability of reducing traffic congestion and assessing fuel reduction resulting from CP was also analyzed. The findings imply that travelers’ mode choice acts as a mediator between the relationship between travelers’ perception and tendency to carpool. Furthermore, results predicted that CP might reduce 0.25 million cars on the road, about 33.6% of the total private vehicles. Thereby, saving up to 546,810 barrels per year, about 3.42% of Pakistan's total petrol consumption. The findings of this study could be helpful for transport planners, environmentalists, and policymakers to implement carpool systems. Thus, reducing traffic congestion and harmful CO2 emissions and maintaining a sustainable environment.

This paper expressed three regression models that predict the lithium-ion battery life for electric cars based on a supervised machine-learning regression algorithm. The Linear Regression, Bagging Regressor, and Random Forest Regressor models will be compared for capacity prediction of lithium-ion batteries based on voltage-dependent per-cell modeling. When sufficient test data is available, three linear regression learning algorithms will train this model to give a promising battery capacity prediction result. The effectiveness of the three linear regression models will be demonstrated experimentally. The experiment table system is built with an NVIDIA Jetson Nano 4GB Developer Kit B01, a battery, an Arduino, and a voltage sensor. The Random Forest Regressor model has evaluated the model's accuracy based on the average of the square of the difference between the initial value and the predicted value in the data set (MSE (Mean Square Error)), and RMSE (Root Mean Squared Error) is smaller than the Linear Regression model, Bagging Regressor model (MSE is 516.332762; RMSE is= 22.722957). The Linear Regression model with MSE and RMSE is the biggest (MSE is 22060.500669; RMSE is= 148.527777). This result allows the Random Forest Regressor model to remain a helpful life prediction of lithium-ion batteries. Moreover, this result allows rapid identification of battery manufacturing processes and will enable users to decide to replace defective batteries when deterioration in battery performance and lifespan are identified.

This study aims to determine the influence of selected social and health factors on the quality of inpatient treatments when regional health organizations use stacking ensemble model. The proposed procedure is based on the logistic regression method, which is used for direct prediction in the case of good fitting data and impossibility of including aggregation of classification algorithms but also in the opposite case, for fine calibration to obtain prediction. In opposite case, the procedure uses classification algorithms and several filter methods which initially rank individual factors according to their importance to reduce the dimensionality of problem and, in such way. obtaining one optimized classification prediction. The proposed procedure is trained using one part and tested using another part of dataset from case study which enables the generalization of the solution to the set goal and is verified by the Kaggle dataset Brest cancer. Case study was conducted using the real data acquired in the region connected to the city of Nis, Republic of Serbia. The obtained results show that the proposed model achieves better results that each of methods included in this stacking ensemble-regression and classification used individually.

Microstructure evolution in metal additive manufacturing (AM) is a complex multi-physics and multi-scale problem. Understanding the impact of AM process conditions on the microstructure evolution and the resulting mechanical properties of the printed part is an active area of research. At the meltpool scale, the thermo-fluidic governing equations have been extensively modeled in the literature to understand the meltpool conditions and the thermal gradients in its vicinity. In many phenomena governed by partial differential equations, dimensional analysis and identification of important dimensionless numbers can provide significant insights into the process dynamics. In this context, a novel strategy using dimensional analysis and the method of linear least squares regression to numerically investigate the thermo-fluidic governing equations of the Laser Powder Bed Fusion AM process is presented in this work. First, the governing equations are solved using the Finite Element Method, and the model predictions are validated by comparing with experimentally estimated cooling rates, and with numerical results from the literature. Then, through dimensional analysis, an important dimensionless quantity - interpreted as a measure of heat ab- sorbed by the powdered material and the meltpool, is identified. This dimensionless measure of heat absorbed, along with classical dimensionless quantities such as Peclet, Marangoni, and Stefan numbers, is used to investigate advective transport in the meltpool for different alloys. Further, the framework is used to study the variations of thermal gradients and the solidification cooling rate. Important correlations linking meltpool morphology and microstructure evolution related variables with classical dimensionless numbers are the key contribution of this work.

Background: In Switzerland, Aedes albopictus is well established in Ticino, south of the Alps, where surveillance and control are implemented. The mosquito has also been observed in Swiss cities north of the Alps. Decision-making tools are urgently needed by the local authorities in order to optimize surveillance and control. Methods: A regularized logistic regression was used to link the long-term dataset of Ae. albopictus occurrence in Ticino with socio-environmental predictors. The probability of establishment of Ae. albopictus was extrapolated to Switzerland and more finely to the cities of Basel and Zurich. Results: The model performed well, with an AUC of 0.86. Ten so-cio-environmental predictors were selected as informative, including the road-based distance in minutes of travel by car from the nearest cell established in the previous year. The risk maps showed high suitability for Ae. albopictus establishment in the Central Plateau, the area of Basel and the lower Rhone Valley in the Canton of Valais. Conclusions: The areas identified as suitable for Ae. albopictus establishment are consistent with the actual current findings of tiger mosquito. Our approach provides a useful tool to prompt authorities’ intervention in the areas where there is higher risk of introduction and establishment of Ae. albopictus.

This study aims at improving the forecast accuracy of primary energy consumptions in China, Japan and South Korea and verifying the correlation in primary energy consumptions among the neighboring countries. Considering the diversity of primary energy composition, this study selects 6 components of primary energy, including oil, coal, natural gas, nuclear energy, hydropower and renewable energy as characteristic variables. A collaborative prediction model based on SVR for primary energy consumption prediction is proposed to explore the correlation of primary energy consumption among three countries in China, Japan and South Korea. The results show that there is a strong correlation between primary energy consumption when multiple countries make collaborative prediction, among which the primary energy consumption of South Korea has the largest impact on the primary energy consumption of China and Japan. In the primary energy cooperation of China-Japan-South Korea, a primary energy cooperation system with the South Korea as the link should be established through regional coordination to alleviate the shortage of traditional fossil energy.

The COVID-19 outbreak has severely affected the social and economic conditions across this globe. Little is known about the relationship of COVID-19 with countries’ economic and socio-demographic status. Publicly available data on COVID-19 test rate, attack rate, case fatality rate, and recovery rate were analyzed in relation to country’s economic status, population density, median age, and urban population ratio. We also conducted multinomial logistic regression analysis to predict the influence of countries’ social and economic factors on COVID-19. The results revealed that the median age had significant positive correlation with attack rate (r=0.2389, p=0.003), case fatality rate (r=0.3207, p=0.000) and recovery rate (r=0.4847, p=0.000). The urbanization has positive significant correlation with recovery rate (r=0.1957, p= 0.016). The multinomial logistic regression analysis revealed low-income countries are less likely to have an increased recovery rate (p=0.000) and attack rate (p=0.016) compare to high-income countries. The lower-middle-income and upper-middle-income countries are less likely to have an increased recovery rate (p=0.000 and p=0.001, respectively) compared to high-income countries. Based on the result of this study, these economic and socio-demographic factors should consider in designing appropriate preventive measures as a next step. The low and lower-middle-income countries should invest more in health care services to lower the case fatality rate and increase test and recovery rates as part of pandemic preparation like COVID-19. As the number of COVID-19 attacks, death and recovery rates are constantly changing; however, the intensive study is required to obtain a clear picture.

This study presents a new kinetic scheme for the mass yield prediction of waste lignocellulosic biomasses treated by Hydrothermal Carbonization (HTC). The proposed reactions are based on the decomposition, solubilization, and polymerization of each main fraction of the biomass: cellulose, hemicellulose, and lignin. The ash content was assumed to be inert. The kinetic parameters have been obtained by non-linear adjustment using a data set with 220 experimental runs collected from the literature. The results indicate that the pre-exponential factors range was from 7.33 x10¹ to 1.412x10⁵ min^-1, and activation energies were between 33.75 y 225.3 kJ/mol. A good fit is achieved between the observed and predicted data with an R² of 0.81 and an RMSE of 7.7 %. The proposed scheme was validated with the experimental data obtained by the HTC of sawdust (Pinus radiata) and rapeseed (Brassica napus). The experiments were carried out at temperatures of 190, 220, and 250 ºC and reaction times of 0, 30, 60, 90, and 120 min. The predicted values showed an average error of 2.3 and 3.5 %, respectively. Therefore, the kinetic scheme is a useful tool in the conversion analysis of waste biomass treated by HTC.

This work evaluates the surface water quality in terms of physico-chemical parameters of the Brahmani River, Odisha using statistical analysis involving the calculation of correlation coefficient and regression equation. Besides this, the work also highlights and draws attention towards the “Water Quality Index” in a simplified format which may be used at large and could represent the reliable picture of water quality. Surface water quality data is taken from OSPCB of various location i.e. Panposh D/S, Rourkela D/S, Rengali, Talcher U/S, Kamalanga D/S, Bhuban, Pattamundai and was assessed for summer, monsoon, winter for the years 2011, 2012, 2013, 2014 and 2015. Average of values, minimum of values and maximum of values of water quality parameters were obtained seasonally over the above mentioned years. Besides this, the standard deviation for the water quality parameters was also obtained for water quality parameters namely pH, Temperature, DO, TDS, Alkalinity, EC, Na+, Ca2+, Mg2+, K+, F-, Cl-, NO3-, SO42- and PO42-. Seasonal changes in various physical and chemical parameters were analysed.The values obtained were compared with the guideline values for drinking water by Bureau of Indian Standard (BIS). A systematic correlation and regression study is carried out for three seasons, showed linear relationship among different water quality parameters. This provides an easy and rapid method of monitoring water quality. Highly significant (0.8< r <1.0), moderately significant (0.6< r <0.8) and significant (0.5< r <0.6) correlations between the parameters have been worked out. High correlation coefficient has been observed between TDS,EC-Na+, Ca2+, Cl-, SO42- ; Na+- Cl-. From the collected quantities, certain parameters were selected to derive WQI for the variations in water quality of each designated sampling site. WQI of Brahmani River ranged from 36.7 to 44.1 which falls in the range of good quality of water.Panposh D/S and Rourkela D/S showed poor water quality in summer and winter season. It is shown that WQI may be a useful tool for assessing water quality and predicting trend of variation in water quality at differentlocations in the Brahmani River.

The effect of sensitivity points (sequence order and position of every element) of sequences following comparative optinalysis under two proposed mechanisms, the paranodic and synodic skewization, was studied to develop a modeling approach to comparative optinalysis of sequences. The results show that the outcomes of comparative optinalysis (similarity measurement) in a set of paranodically skewed sequences can be modeled deterministically by suitable line regression functions. The sensitivity points (nodes) of a sequence display two important and distinct zones, the K-zones and the B-zones. Continues paranodic skewization within these zones (KB zones) operates within probability space, but at hyperskewization level and at the K-zones only, the outcomes of comparative optinalysis operate outside the probability space. Moreover, the outcomes of comparative optinalysis by synodic skewization can be modeled deterministically by some regression line functions, but a general regression function cannot be identified. At certain limit of skewization value space, following paranodic and synodic skewization, the outcomes of comparative optinalysis at the left-sided sequence form a similar pattern with the right-sided sequence.

The growth of demand for metallic minerals has faced with the need for new techniques and improving technologies for all mine life cycle operations. Nowadays, the exploitation of old tailings and mine wastes facilities could represent a solution to this demand, with economic and environmental advantages. W-Sn Panasqueira Mine has been operating for more than 100 years. Its first processing plant “Rio” was located near Zêrere river being the mineral processing residues deposited on the top hillside on the margin of this river in Cabeço do Pião tailings dam. The lack of maintenance and monitoring of this enormous structure in the last twenty years represents high risks to the environment and population of the surrounding region. The re-mining of the tailings by hydrometallurgical methods was considered, in order to satisfy these two enounced conditions - metals demand and environmental risk, aiming for the sale of the metal to pay the environmental intervention. Field samples campaign allowed collecting data and results from laboratory tests driving to use regression optimization. The re-mining solution was studied, taking into account the technical, economic, social, and environmental aspects.

There is a large body of research on determining the impact of field variability of soil on crop yields. In contrast, site-specific information about crop responses to agronomic treatments is less frequent. On-Farm Precision Experimentation (OFPE) brings important information to understand the spatial variation of crop response to agronomic practices and thus to improve agronomic decisions. The objective of this work was to investigate the spatial variability of corn yield responses to nitrogen and seed rates using OFPE in four fields in the US Midwest. Geographically weighted regression was applied to generate local regression coefficients, which were used to delineate response zones in each field. The results showed the existence of great potential to adjust the rates of these inputs according to the response of each zone identified by the proposed method. The results of this study can be applied to reevaluate expectations on variable rate prescriptions guided largely by soil and variability.

Regional declines of the Korean fir (Abies koreana) have been observed since the 1980s on the subalpine region. To explain this decline, it is fundamental to investigate the degree to which environmental factors have contributed to plant distributions on diverse spatial scales. We applied a hierarchical regression model to determine quantitatively the relationship between the abundance of Korean fir (seedlings) and diverse environmental factors across two different ecological scales. We measured Korean fir density and the occurrence of its seedlings in 102 (84) plots nested at five sites and collected a range of environmental factors at the same plots. Our model included hierarchical explanatory variables at both site-level (weather conditions) and plot-level (micro-topographic factors, soil properties, and competing species). The occurrence of Korean fir seedlings was positively associated with moss cover and rock cover but negatively related to dwarf bamboo cover. On site-level, winter precipitation was significantly positively related to the occurrence of seedlings. A hierarchical Poisson regression model revealed that Korean fir density were negatively associated with slope aspect, topographic position index, Quercus mongolica cover, and mean summer temperature. Our results suggest that drought and competition with other species are factors which halt the survival of Korean fir. We can predict that the population of Korean fir will continue to decline on the Korean Peninsula due to rising temperatures and seasonal drought, and only a few Korean fir will survive on northern slopes or valleys where competition with dwarf bamboo and Q. mongolica can be avoided.

Widely used in hydraulics, the Colebrook equation for flow friction relates implicitly to the input parameters; the Reynolds number, Re and the relative roughness of inner pipe surface, ε/D with the output unknown parameter; the flow friction factor, λ; λ=f(λ, Re, ε/D). In this paper, a few explicit approximations to the Colebrook equation; λ≈f(Re, ε/D), are generated using the ability of artificial intelligence to make inner patterns to connect input and output parameters in explicit way not knowing their nature or the physical law that connects them, but only knowing raw numbers, {Re, ε/D}→{λ}. The fact that the used genetic programming tool does not know the structure of the Colebrook equation which is based on computationally expensive logarithmic law, is used to obtain better structure of the approximations which is less demanding for calculation but also enough accurate. All generated approximations are with low computational cost because they contain a limited number of logarithmic forms used although for normalization of input parameters or for acceleration, but they are also sufficiently accurate. The relative error regarding the friction factor λ, in best case is up to 0.13% with only two logarithmic forms used. As the second logarithm can be accurately approximated by the Padé approximation, practically the same error is obtained also using only one logarithm.

Censoring occurs when complete follow-up time information is unavailable for patients enrolled in a clinical study. The process is considered to be informative (nonignorable) if the likelihood function for the censoring model cannot be partitioned into a set of response parameters that are independent of the censoring parameters. In such cases, estimated survival time probabilities may be biased, prompting the need for special statistical methods to remedy the situation. The problem is especially salient when censoring is skewed toward the early phase of a study. In this paper, we describe a method to impute censored follow-up times using a counting process method.

Throughout the world, disabilities people have worse health prospects, lower education levels, lower economic participation, and higher poverty rate in comparative terms to people without disabilities. For disabilities people achieve better, more long-lasting prospects, we must empower these people and remove barriers that restrict them from participating in the community have access to quality education, to find decent work and have their voices heard. In statistical terms, a very useful alternative that can provide support and monitoring of public policies in this area is proposing to be used continuously. A risk index called risk index disabled person who is to assess which factors are associated to this risk, as well as the intensity and direction of each of these factors, yielding a final score that can be sorted or classified according to the probability of people acquire a certain disability. In the Brazilian case, we propose the use of techniques such as binary and ordinal logistic regression to select the most significant factors using criteria such as AIC, BIC and DIC. Calculate the risk probability for different disabilities (see, hear, move and intellectual) and number of disabilities to the dataset Sample of respondents for Full Questionnaire at IBGE 2010 Census. In this work, by using stereotype ordinal logistic model with ordinal response, it was possible to improve the fit quality, to be compared with binary response logistic model. By using ordinal response merged the disability risk for different severity degree and amount of deficiencies. Mains conclusions were: i)the model required a smaller number of explanatory variables was intellectual or mental and greater number was disabilities; ii) the most sensitive adjust was using stereotype ordinal logistic; iii) different disabilities aren´t homogenous as the different predictor variables, and finally; iv) higher incidence of risks were noted visual disability, living in the northeast, female, age 80, yellow race, instruction level until incomplete fundamental, works production form their own consumption and high number of children.

Caudal regression syndrome (CRS) is a congenital abnormality characterized by an incomplete development of the spinal cord (SC) and other abnormalities. We studied a 9-months old CRS child presenting: interruption of SC at L2-L3 level, sacral agenesis, lack of innervation of the inferior limbs (flaccid paraplegia) and neurogenic bladder and bowel. Given the effects of growth hormone (GH) on the proliferation, differentiation and migration of neural stem cells (NSCs), we treated him with GH and rehabilitation, trying to induce the recovery of main sequelae. GMFM-88 test score was 12.31%. After a blood analysis, GH treatment (0.3 mg/day, 5 days/week, 3 months and then 15 days without GH) and rehabilitation commenced. This protocol was followed during 5 years, being the last GH dose 1 mg/day. Blood analysis and physical exams were performed every 3 months initially and every 6 months later. Six months after commencing the treatment GMFM-88 score increased to 39.48%. Responses to sensitive stimuli appeared in most of the territories explored; 18 months later sensitive innervation was complete and the patient moved any muscle over the knees and controlled his sphincters. Three years later he walked with the help of canes, there was plantar flexion and GMFM-88 score was 78.48%. In summary, GH plus rehabilitation may be useful for innervating distal territories, below the level of the incomplete spinal cord in CRS. Most likely, GH acts on ependymal SC NSCs, as the hormone does in the neurogenic niches in the brain.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

This paper uses panel data to find the determinants of tracking errors in exchange traded funds (ETFs) in the Hong Kong stock market. A comparison of tracking errors between physical and synthetic ETFs also indicates that the synthetic ETFs have higher tracking errors. The magnitude of tracking errors is found to be negatively related to size but positively related to dividend yield, trading volumes of funds, and market risk. However, this study also finds that expense ratio has a negative impact on tracking error, which is not consistent with previous studies, and which this paper addresses.

Understanding the optimal strategy for a real estate investment and how performance changes based on characteristics is crucial for optimising the achievable return. This is prominent in tourist areas such as Paphos where there is no clear distinction as to whether short or long-term approaches are optimal. The study aimed to develop a model for predicting the optimal rental strategy whilst assessing which model performed best and which property attributes impacted its return the greatest. Short-term data was collected from AirDNA and long-term data was manually collected from real estate agents websites. Furthermore, Random Forest, K-Nearest Neighbour and Multiple Linear Regression models were created to predict the highest and best use for each property. Model accuracy varied between data sets with the best performing model for short-term properties being Random Forest (R-Squared: 0.843), and Distance-Based Multiple Linear Regression for long-term approach (R-Squared: 0.843). The study demonstrated that accurate models could be created to predict the optimal rental strategy with the number of bedrooms being the main driver for rental income, followed by luxury finishes and the presence of a pool. It found that locational characteristics didn’t impact the returns significantly assuming that the property was located within a tourist area.

Melioidosis is an endemic infectious disease caused by Burkholderia pseudomallei bacteria, which contaminates soil and water. To better understand the environmental changes that have contributed to melioidosis outbreaks, this study used spatiotemporal analyses to clarify the distribution pattern of melioidosis and the relationship between melioidosis morbidity rate and local environmental indicators (land surface temperature, normalised difference vegetation index, normalised difference water index) and rainfall. A retrospective study was conducted from January 2013 to December 2022, covering data from 219 sub-districts, with each exhibiting varying morbidity rate of melioidosis on a monthly basis. Spatial autocorrelation was determined using local Moran’s I, and the relationship between melioidosis morbidity rate and the environmental indicators was evaluated using geographically weighted Poisson regression. The results revealed clustered spatiotemporal patterns of melioidosis morbidity rate across sub-districts, with hotspots predominantly observed in the northern region. Furthermore, we observed a range of coefficients for the environmental indicators, varying from negative to positive, which provided insights into their relative contributions to melioidosis in each local area and month. These findings highlight the presence of spatial heterogeneity driven by environmental indicators and underscore the importance of public health offices implementing targeted monitoring and surveillance strategies for melioidosis in different locations.

Objective: To evaluate the variables influencing the length of stay (LoS) for COVID-19 ICU patients at Tygerberg Hospital (Cape Town) and to identify the covariates that significantly influenced it and any potential risk factors associated with LoS. Methods and Results: Poisson, negative binomial (NB), Hurdle–Poisson, and Hurdle–NB regression models were used to model the LoS in this prospective cohort study. The fitted models were compared using the Akaike information criterion (AIC), Vuong’s test criteria, and Rootograms. Based on the chosen performance criteria, the NB model provided the best fit outperforming other candidate models. The baseline LoS count was 8 days. On average, antibiotics reduced LoS by 0.74-fold (95% CI 0.62-0.89) compared to not taking antibiotics. The second wave had a significant effect on the average LoS, which decreased by 0.36-fold (95% CI 0.14-0.93) compared to the first wave. Average LoS increased by 1.01-fold (95% CI 1.01-1.02) for every one-year increase in the age of the patient and by 1.02-fold (95% CI 1.01-1.03) for every 1 unit increase in neutrophils. A 1 ng/L increase in log (TropT) levels decreased the average LoS by 0.87-fold (95% CI 0.81-0.93) similarly, a unit increase in the PF ratio decreased the average LoS by 0.998-fold (95% CI 0.997-0.999) respectively. Conclusion: The study identified common clinical characteristics associated with length of stay in ICU for COVID-19 patients, including age at admission, PF ratio, neutrophils, TropT, Wave, and antibiotic use. These results can aid in identifying risk factors for increased length of stay, assist in healthcare systems planning, and aid in evaluating different models for analysing this type of data.

The conformity assessment of products or a measured value with the given standards is carried out based on the global risk of producers and consumers calculation. A product may conform to specifications but be falsely rejected as non-conforming. This is about the producer's risk. If a product doesn't meet the requirements but is falsely accepted as conforming, that poses a risk to the consumer. The conventional approach to risk assessment, which yields only a single numerical value for the global risk of producers and consumers, is naturally extended, and utilized for assessing risk in measurement models with linear regression. The outcomes of the two-dimensional extension, along a moderate scale, are the parabolas with an opening upwards. Risk surfaces were obtained through three-dimensional extension over the area limited by the moderate scale and guard band axes. Four models with different ranges of tolerance intervals were used to test this innovative method of risk assessment in linear regression. The corresponding standard measurement uncertainties are determined by applying a simplified measurement model with the use of comprehensive data on the measurement performance and by determining measurement uncertainty derived from consideration of the functional relationship obtained by linear regression analysis. Models that utilize information from linear regression analysis to determine measurement uncertainty are biased towards risks at the edges of the moderate scale. Testing the model's performances with metrics related to the confusion matrix, such as the F1 score, further substantiated this assertion. The diagnostic odds ratio has been proven to be extremely effective in identifying the curve along the guard band axis, along which the global risks of producers and consumers are at their lowest.

In this paper, a distributed algorithm is proposed to solve a consensus convex optimization problem. It is a Jacobi-proximal alternating direction method of multipliers with a damping parameter $\gamma$ in the iteration of multiplier. Compared with existing algorithms, it has the following nice properties: (1) The restriction on proximal matrix is relaxed substantively, thus alleviating the weight of the proximal term. Therefore, the algorithm has a faster convergence speed. (2) The convergence analysis of the algorithm is established for any damping parameter $\gamma\in(0,2]$, which is larger ones in the literature. In addition, some numerical experiments and an application to a logistic regression problem are provided to validate the effectiveness and the characteristics of the proposed algorithm.

Febrile neutropenia (FN) is a major concern in patients undergoing chemotherapy for diffuse large B-cell lymphoma (DLBCL); however, the overall risk of FN is difficult to assess. This study aimed to develop a model for predicting the occurrence of FN in patients with DLBCL. In this multicenter, retrospective, observational analysis, a multivariate logistic regression model was used to analyze the association between FN incidence and pretreatment clinical factors. We included adult inpatients and outpatients (aged ≥ 18 years) diagnosed with DLBCL who were treated with chemotherapy. The study examined 246 patients. Considering FN occurring during the first cycle of chemotherapy as the primary outcome, a predictive model with a total score of 5 points was constructed as follows: 1 point each for viral hepatitis, extranodal involvement, and a high level of soluble interleukin-2 receptor and 2 points for lymphopenia. The area under the receiver operating characteristic curve of this model was 0.844 (95% confidence interval: 0.777–0.911). Our predictive model can assess the risk of FN before patients with DLBCL start chemotherapy, leading to better outcomes.

For a long time, there has been interest in the relationship between personality traits and life satisfaction. However, many previous studies suffer from small sample sizes or selective sampling, sometimes leading to biased or imprecise results. The current study, which focuses on the trait of extraversion, attempts to overcome these limitations by using a large-scale German survey of more than 40,000 individuals aged 10 to 72. As the descriptive and regression results clearly show, there is a statistically significant relationship between extraversion and several dimensions of current life satisfaction. Depending on the type of satisfaction, the unstandardized regression coefficients range from 0.18 to 0.33. To gain further insight, age is added as an explanatory variable to test whether these associations change as a person ages. The results show that the effect sizes sometimes differ by age but remain robust and statistically significant. In conclusion, the study adds to the literature by providing convincing evidence that extraversion and life satisfaction are positively associated, at least in Western and industrialized countries, and that there are interaction effects with age.

In the Mediterranean Sea, there are two critical issues affecting marine benthic biocenosis: the sedimentation process and the increasing trend in marine biodiversity loss. These processes are very marked along the western side of Calabria coastline where siltation is one of the main reasons for the regression of Posidonia beds in the regional coastal waters. This research aims to investigate the relationships between the geomorphological features of the debris source areas, represented by fluvial basins, and the distribution of Posidonia meadows. So, a geomorphological study of the Tyrrhenian fluvial basins with area greater than 200 km2 and its correlation with the mapping of the meadows in the Calabria Tyrrhenian waters was carried out. Furthermore, in order to assess the increased level of burial in a Posidonia oceanica meadow and its health state over time, a program of Posidonia monitoring was undertaken between 2000 and 2010, in a test area located in the Marine Regional Park of Isca (Calabria, Southern Italy). The results of this survey highlighted that, at the beginning of the study period, for a silting rate of 4 - 5 cm/year, the meadow suffered a reduction of its photosynthetic ratio with a rate of mortality of 50%. In the following years, the siltation rate reach 12 cm/year in 2010 and the meadow began to disappear. Therefore, the marine pollution by sedimentation represents a serious factor for the regression of Posidonia oceanica meadows, enhancing the risk of a gradual loss in marine biodiversity.

In China, the majority of mountainous regions are characterized by complex topography and a delicate, sensitive geological environment. Coupled with a generally underdeveloped infrastruc-ture and numerous unreasonable human engineering activities, these regions are often highly susceptible to geological disasters. Geological hazards can cause significant damage to human lives and property, impeding the development of mountainous areas. Consequently, researching the assessment of geological hazard vulnerability is crucial for disaster prevention, emergency management, and economic development in these regions. This study focuses on Xuanwei City and selects eight factors for evaluation, including elevation, gradient, slope aspect, normalized vegetation index, stratigraphic lithology, distance from faults, distance from rivers, and distance from roads. These factors are chosen based on a comprehensive analysis of the spatial and tem-poral distribution of geological hazards and disaster incubation conditions. Two paired models, the deterministic coefficient model + logistic regression model (CF+LR) and the information quan-tity model + logistic regression model (I+LR), were employed to quantitatively assess the study ar-ea. The accuracy of these models was evaluated using ROC curves and AUC values. The results indicate that: (1) The AUC values for the CF+LR and I+LR coupled models are 0.799 and 0.772, respectively, demonstrating that both models can objectively and reliably assess the vulnerability to geological hazards in the study area; (2) Based on the CF+LR model calculations, the geological hazard susceptibility of Xuanwei City can be categorized into four zones: extremely high suscepti-bility (6.09%), high susceptibility (31.08%), medium susceptibility (32.26%), and low susceptibility (30.57%); (3) The CF+LR model more accurately represents the evaluation results and offers a strong reference value.

We present an attempt to estimate the long-term changes of Relative Sea Level (RSL) and the different factors contributing to such trends on a local and regional scale using a statistical linear model. The time series analysed correspond to 17 tide-gauges grouped in three different areas: the northern and western Atlantic coasts of the Iberian Peninsula, the Canary Islands, and the southern and eastern coasts of the Iberian Peninsula and Balearic Islands. The analysis was performed for two periods: 1948-2019, using tide-gauge data, and 1993-2019, using both tide-gauge and altimetry data for comparison. The trends for the period 1948-2019 ranged between 1.09 0.14 (Canary Islands) and 2.05 0.21 mm/yr, for the northern and western Atlantic Iberian Peninsula. Altimetry data during the period 1993-2019 yielded quite homogeneous results for all the locations and regions, ranging between 2.7 0.4 and 3.0 0.3 mm/yr. On the contrary, the results obtained from tide-gauge data for this recent period showed a large dispersion, very likely due to local effects or even levelling or instrumental errors. Nevertheless, when the results were averaged for each area, the observed trends were comparable to the altimetry results, with values of 2.3 0.8, 2.7 0.5 and 2.8 0.8 mm/yr for the three regions of study. A stepwise forward linear regression has been used to relate the observed RSL variability to the atmospheric forcing and the thermosteric and halosteric components of the sea level. Surprisingly, the thermosteric and halosteric contributions were not significantly correlated to the observed RSL in many cases, and consequently the steric, the total addition of mass, the mass of salt, and the freshwater contributions to the observed sea level trends could not be reliably estimated. This result seems to be the consequence of the scarcity of temperature and salinity data. This hypothesis is confirmed by the exception of L’Estartit tide-gauge. This location is close to a well sampled region. In this case, the atmospheric variables and the thermosteric and halosteric terms explained the 80 % of the observed RSL variance and the contributions of these terms could be estimated. The freshwater contribution for this location was between 1.3 and 1.4 mm/yr, consistent with recent estimations of the contributions of glaciers and Greenland and Antarctica Ice Sheets. These results highlight the importance of monitoring programs and routine sampling for the determination of the different factors contributing to the sea level variability.

Influential Observations, which are outliers in x direction, y direction or both, remain a hitch in classical regression model fitting. Spatial regression model, with peculiar nature of outliers due to their local nature, is not free from the effect of such influential observations. Researchers have adapted some classical regression techniques to the spatial models and yielded satisfactory results. However, masking or/and swamping remain stumbling block to such methods. We obtained the spatial representation of the classical regression measures of diagnostic in general spatial model. Commonly used diagnostic measure in spatial diagnostic, the Cook's distance, is compared to some robust methods, Hi2 (using robust and non-robust measures), and classification based on generalized residuals and diagnostic generalized potentials, ISRs-Posi and ESRs-Posi, with the help of the obtained spatial prediction residuals and the spatial leverage term. Results of simulation and applications to real data have shown the advantage of the ISRs-Posi and ESRs-Posi due to classification of outliers over Cook's distance and non-robust Hsi12, which suffer from masking, and robust Hsi22 which suffer from swamping in general spatial model.

Most existing flexible count regression models allow only approximate inference. Balanced discretization is a simple method to produce a mean-parametrizable flexible count distribution starting from a continuous probability distribution. This makes easy the definition of flexible count regression models allowing exact inference under various types of dispersion (equi-, under- and overdispersion). This study describes maximum likelihood (ML) estimation and inference in count regression based on balanced discrete gamma (BDG) distribution and introduces a likelihood ratio based latent equidispersion (LE) test to identify the parsimonious dispersion model for a particular dataset. A series of Monte Carlo experiments were carried out to assess the performance of ML estimates and the LE test in the BDG regression model, as compared to the popular Conway-Maxwell-Poisson model (CMP). The results show that the two evaluated models recover population effects even under misspecification of dispersion related covariates, with coverage rates of asymptotic 95% confidence interval approaching the nominal level as the sample size increases. The BDG regression approach, nevertheless, outperforms CMP regression in very small samples (n = 15 − 30), mostly in overdispersed data. The LE test proves appropriate to detect latent equidispersion, with rejection rates converging to the nominal level as the sample size increases. Two applications on real data are given to illustrate the use of the proposed approach to count regression analysis.

The COVID-19 disease spreads swiftly, and nearly three months after the first positive case was confirmed in China, Coronavirus started to spread all over the United States. Some states and counties reported an extremely high number of positive cases and deaths, while some reported too few COVID-19 related cases and mortality. In this paper, the factors that could affect the transmission of COVID-19 and its risk level in different counties have been determined and analyzed. Using Pearson Correlation, K-means clustering, and several classification models, the most critical ones were determined. Results showed that mean temperature, percent of people below poverty, percent of adults with obesity, air pressure, percentage of rural areas, and percent of uninsured people in each county were the most significant and effective attributes.

This research is aimed at evaluating two different scenarios, firstly, appraising the impacts of employing the concepts of Total Quality Management (TQM) to the construction projects in Saudi Arabia. The results of the study were obtained through utilization of a descriptive analytical approach, where 300 questionnaires were distributed to engineering firms and companies with a response rate of 200 questionnaires, hence achieving the study sample for this research. The data gathered was analyzed by applying the Statistical Package for Social Science (SPSS) program and calculating the Relative importance index (RII) and the mean values. From the research conducted, the outcomes showed that the management’s ability to commit using TQM while applying BIM obtained a relative importance of (0.717), while the relative importance for the management’s ability to commit using TQM without the application of BIM is (0.552). The results showed that construction projects in Saudi Arabia still sustain setbacks from applying TQM concepts and suffer from the lack of administrative, scientific and technical applications. In a second scenario, a hybridized support vector regression (SVR) Harris-hawks optimization (HHO) (i.e., SVR-HHO) were used to predict the TQM. The performance accuracy of the models was checked through three different evaluation metrics namely; mean square error (MSE), correlation co-efficient (CC) and Nash-Sutcliffe efficiency (NSE). the hybridized emerging SVR-HHO outperformed the other two data driven approaches in both the training and testing stages based on the employed evaluation metrics. Overall, the obtained results showed that both the machine learning and metaheuristic approaches were capable of predicting TQM.

Objective: Application of ERA methods to investigate the atmospheric pollution and built environment factors influencing lung cancer incidence rate in Chinese women. Methods: Lung cancer incidence rate among Chinese women at 339 cancer registries were obtained from the China Cancer Registry Annual Report 2017, air quality and built environment data were obtained from the Greenpeace and China Construction Yearbook. After multiple covariates variables were eliminated, an exploratory regression analysis was performed using the world standardized population incidence rate as the dependent variable. Air quality and built environment factors as the independent variable. Results: Shandong Peninsula, Hebei and Liaoning are high incidence rate areas of female lung cancer in China, with significant regional aggregation. In addition to air quality factors such as industrial smoke emission data, the association between built environmental factors such as urbanization rate, development LUI, population density and greening coverage of built-up areas and female lung cancer incidence rate is statistically significant. Conclusion: In addition to air quality factors, urban spatial factors can also significantly affect respiratory health. The LUI is positively while urbanization rates and population density are negatively correlated with the incidence rate of lung cancer. The role of green space for respiratory health has not been proven. In addition, there is little relationship between income and health, and similar findings are found for indicators such as the public transportation and roads network.

The study explored the contribution of ICT-based information sources to market participation among smallholder livestock farmers. Use of ICTs is considered paramount for providing smallholder farmers with required market information, in order to reduce market asymmetries. A Double Hurdle regression was utilized to analyze data collected from 150 smallholder livestock farmers in the study area. The results show that while use of ICT-based market information sources significantly influenced market participation, the effect of using ICT-based information sources on intensity of market participation was not significant. Other variables shown to influence both market participation and the intensity of market participation were age, additional income and membership of farmer cooperatives. This suggests the need to also consider other associated factors in the application of interventions which utilize ICT-based information sources in achieving planned market interventions.

In recent years, online social media information has been subject of study in several data science fields due to its impact on users as a communication and expression channel. Data~gathered from online platforms such as Twitter has the potential to facilitate research over social phenomena based on sentiment analysis, which usually employs Natural Language Processing and Machine Learning techniques to interpret sentimental tendencies related to users opinions and make predictions about real events. Cyber attacks are not isolated from opinion subjectivity on online social networks. Various security attacks are performed by hacker activists motivated by reactions from polemic social events. In this paper, a methodology for tracking social data that can trigger cyber attacks is developed. Our main contribution lies in the monthly prediction of tweets with content related to security attacks and the incidents detected based on ℓ1 regularization.

To estimate the recreational value provided by the Foy’s Lake annually using the most applicable model for on-site data is the main objective of this study. Adhere to the objective of this study; Individual Travel Cost Method (ITCM) has been applied and Zero Truncated Poisson Regression Model has been found plausible among other models to estimate consumer surplus. Based on the findings of the study, an estimate of the consumer surplus or recreational benefits per trip per visitor can be recommended as BDT 5,875 or US $ 73.44 and counting the consumer surplus per trip per visitor, the annual recreational value (total consumer surplus) provided by the lake is found to be BDT 321 million or US $ 40.2 million.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

The reconstruction of traffic accidents has grown as an interdisciplinary field since the first accident occurred. Various methods have been developed over time, starting with primary data collected at the scene of the accident. In this work, I proposed a method by which the value of the force in the safety belt buckle can be determined when it is equipped with a pretensioning system with pyrotechnic trigger in the tube, PBP or PLP type. The anti-return system of the pretensioner mechanism, which prevents the passenger's body from moving forward, contains a set of balls that block the movement of the piston in the pretensioner tube after its activation. When limiting the movement, the force the human body exerts on the safety belt webbing is transformed into the deformation of the pretensioner tube by the balls of the anti-return system. Depending on the magnitude of the force, the marks left by the balls differ. I propose a relationship of dependence between the acting force and the deformation of the tube. An experimental test bench was created to perform shock traction tests on the pre-tensioning system, under similar conditions to those of the human body acting on the belt in case of a frontal collision. Following the tests, the force value of the seat belt buckle cable and the diameter of the spherical indentations that the balls left in the pretensioner tube were measured. A mathematical model was proposed to determine the normal force with which a ball from the anti-return system deforms the tube. The normal force was also determined by two other methods specific to contact mechanics and used in the specialized literature. By comparing the normal forces obtained by the three methods, a good correlation between the proposed mathematical model and the Komvopoulos-Ye method resulted, the "Hardness" method not being suitable for this study. The determined polynomial regression curve allows finding out the force in the cable of the closer depending on the size of the deformations produced by the balls in the tube. The forces in the belt webbing can be thus determined and biomechanics specialists can evaluate the injuries to the chest and abdomen of the occupants of a vehicle.

The presence of escaped fish in aquaculture facilities as a result of harsh meteorological conditions (more pressing in a face of climate change) requires a better understanding of these dynamical behaviour through vigilant monitoring and validated numerical models. In this context, data from strain, stress sensors as well as meteorological and current sensors installed at an aquaculture farm in the Region of Murcia (Spain) were collected, processed and analysed. Among them, first results about the relationship between load and currents sensors are presented. Due to the complexity of the time series, various analyses were conducted to examine their interrelation, encompassing regression analysis of raw data and data segmented into different time intervals. Through this analysis, it was observed that employing distinct time windows better elucidated the data variability. Furthermore, an optimal data window of 240 data was identified, demonstrating significantly improved explanatory power, with the coefficient of determination (R2) increasing by approximately 0.8 depending on the section. This pave the way for optimizing the monitoring features that must be carried out to relate cause-and-effect variables in the behaviour of these off-shore infrastructures.

The aim of this paper is to study a semi-functional partial linear regression model (SFPLR) for spatial data with responses missing at random. The estimators are constructed by the kernel method, and some asymptotic properties such as probability convergence rates of the nonparametric component and asymptotic distribution of the parametric and nonparametric components are established under certain conditions. Next, the performances and the superiority of these estimators are presented and examined using a study on simulated data and on real data by carrying out a comparison between our semi-functional partially linear model with MAR estimator (SFPLRM), the semi-functional partially linear model with the full-case estimator (SFPLRC) and the nonparametric functional model estimator with MAR (FNPM). The results show that the proposed estimators outperform existing estimators as the number of random missing data increases.

Crop digital twin is redefining traditional farming practices, offering unprecedented opportunities for real-time monitoring, predictive and simulation analysis, and optimization. This research embarks on an exploration of the synergy between precision agriculture, crop modeling, and regression algorithms to create a digital twin for augmenting farmers the concentration and composition prediction-based crop nutrient recovery. This captures the holistic representation of crop characteristics, considering the intricate relationships between environmental factors, nutrient concentrations, and crop compositions. However, the complexity arising from diverse soil and environmental conditions makes nutrient content analysis expensive and time-consuming. This paper presents the result of a predictive digital twin case study that employs six regression algorithms namely Elastic Net, Polynomial, Stepwise, Ridge, Lasso, and Linear Regression to predict rice nutrient content efficiently, particularly considering the coexistence and composition of multiple nutrients. Our research findings highlight the superiority of the Polynomial Regression model in predicting nutrient content, with a specific focus on accurate nitrogen percentage prediction. This insight can be used for nutrient recovery intervention by knowing the precise amount of nutrient to be added into the crop medium. The adoption of the Polynomial Regression model offers a valuable tool for nutrient management practices in the crop digital twin, potentially resulting in higher-quality rice production and a reduced environmental impact. The proposed method can be replicable in other low-resourced crop digital twin system.

Background Acute kidney injury (AKI) is a common comorbidity in the intensive care unit (ICU), with higher mortality rate among those who receive continuous renal replacement therapy (CRRT). This study aimed to investigate the association of white blood cell (WBC) levels with all-cause mortality in AKI patients undergoing CRRT. Method We conducted a post hoc analysis of ICU patient data from multiple centers in Korea. First, the levels of WBCs were classified into four groups based on quartiles. Second, the relationship between different WBC levels and mortality was investigated with the Kaplan-Meier (K-M) survival curves, Cox proportional hazards model, and generalized additivity model (GAM). Finally, we used multiple imputation to avoid bias caused by non-randomized missing data. The endpoints were short-term (28 days) and long-term (90 days) mortality. Result In our analysis, a total of 1,100 ICU patients were included. Among them, 670 (60.90%) and 781 (71.00%) died within 28 and 90 days, respectively. K-M survival curves showed that patients with the lowest WBC levels had the highest risk of mortality for both outcomes. Adjusted multivariate Cox regression analysis confirmed that compared with the reference level (quartile 2), low WBC levels increased the risk of both 28-day mortality (quartile 1, HR = 1.43, 95% CI: 1.13–1.83, P = 0.004) and 90-day mortality (quartile 1: HR = 1.32; 95% CI: 1.05-1.66, P = 0.016). GAM analysis showed a non-linear, U-shaped relationship between pre-CRRT WBC levels and all-cause mortality (non-linear P < 0.05). Conclusion The baseline WBC level is an independent predictor of prognosis for ICU patients receiving CRRT. Patients in the lowest WBC quartile had the highest risk of all-cause mortality. These results provide further evidence that early observation and intervention may have a prognostic value for these high-risk patients.

We present a new penalized method for estimation in sparse logistic regression models with group structure. Group sparsity suggests us to consider the Group Lasso penalty. Being different from penalized log-likelihood estimation, our method can be viewed as a penalized weighted score function method. Under some mild conditions, we provide non-asymptotic oracle inequalities promoting group sparsity of predictors. A modified block coordinate descent algorithm based on a weighted score function is also employed. The net advantage of our algorithm over the existing Group Lasso-type procedures is that the tuning parameter can be pre-specified. The simulations show that this algorithm is considerably faster and more stable than competing methods. Finally, we illustrate our methodology with two real data sets.

Spatial interpolation of meteorological data can have immense implications on risk management and climate change planning. Kriging with external drift (KED) is a spatial interpolation variant that uses auxiliary information in the estimation of target variable at unobserved locations. However, the traditional KED methods with linear trend functions may not be able to capture the complex and non-linear interdependence between target and auxiliary variables, which can lead to an inaccurate estimation. In this work, a novel KED method using least squares support vector regression (LSSVR) is proposed. This machine learning algorithm is employed to construct trend functions regardless of the type of variable interrelations being considered. To evaluate the efficiency of the proposed method (KED with LSSVR) relative to the traditional method (KED with a linear trend function), a systematic simulation study for estimating the monthly means temperature and pressure in Thailand in 2017 was conducted. The KED with LSSVR is shown to have superior performance over the KED with the linear trend function.

In this study, long-term mortality effects associated with exposure to PM10, PM2.5, BC (black carbon), and NOx were analyzed in a cohort in southern Sweden during the period from 1991‒2016. Participants (those residing in Malmö, Sweden, born between 1923‒1950) were randomly recruited from 1991‒1996. At enrollment, 30,438 participants underwent a health screening, which consisted of questionnaires about lifestyle and diet, a clinical examination, and blood sampling. Mortality data were retrieved from the Swedish national cause of death register. The modeled concentrations of PM10 (particles with an aerodynamic diameter smaller than or equal to 10 µm), PM2.5 (particles with an aerodynamic diameter smaller than or equal to 2.5 µm), BC (black carbon), and NOx (nitrogen oxides) at the cohort participants' home addresses were used to assess air pollution exposure. Cox proportional hazard models were used to estimate the associations between long-term exposure to PM10, PM2.5, BC, and NOx and the time until death among the participants during the period from 1991‒2016. The hazard ratios (HRs) associated with an interquartile range (IQR) increase in each air pollutant were calculated based on the exposure lag windows of the same year (lag0), 1‒5 years (lag1‒5), and 6‒10 years (lag6‒10). Three models were used with varying adjustments for possible confounders including both single-pollutant estimates and two-pollutant estimates. With adjustments for all covariates, the HRs for PM10, PM2.5, BC, and NOx in the single-pollutant models at lag1‒5 were 1.06 (95% CI: 1.02‒1.11), 1.01 (95% CI: 0.95‒1.08), 1.07 (95% CI: 1.04‒1.11), and 1.11 (95% CI: 1.07‒1.16) per IQR increase, respectively. The HRs were in most cases decreased by the inclusion of a larger number of covariates in the models. The most robust associations were shown for NOx, with statistically significant positive HRs in all models. An overall conclusion is that road traffic-related pollutants had a significant association with mortality in the cohort.

Cropland area is closely related to food production. More previous focuses were paid on impacts of extreme events on food production, but less on cropland dynamics. This study took the Farming-Pastoral Ecotone of Northern China (FPEN) as a case area, to investigate its cropland area dynamics and driving factors in view of perspectives of extreme events, environmental conditions, socioeconomic development, urban expansion, and ecological construction. We used ridge regression approach to quantify contributions of these drivers to cropland area dynamics. Results showed that cropland area increased significantly at a rate of 333.5km2/a during 1992−2020 and were spatially clustered in east of the FPEN. Impact extent and size each driving factor on cropland trend presented large spatiotemporal differences, but ecological construction (EC) had overall the greatest impact on cropland area changes, followed by urban expansion (UE). In comparison, TL10p has the smallest. UE-dominated areas increased 41.9% since 2010s, but still less than EC. Furthermore, we found that extreme events effects on cropland area trend evidently increased. Particularly, TH90p displayed the most increase (~99.4%). Cropland area changes dominated by extreme temperature events in 2010−2020 increased nearly six times than that in 1992−2010. These findings suggest that increasing impacts of extreme weather events on cropland area changes should be cautioned.

Air pollution in urban centers depends directly on anthropogenic activities. The objective of the present study was to predict tropospheric ozone levels from temperature data in the city of Durango, Dgo. Temperature and tropospheric ozone values were obtained from 18 sampling points in the urban area of the city of Durango, of which 15 were obtained by collecting from the Ventusky service and the rest from three fixed monitoring stations established in the city. These values were interpolated in order to determine the spatial values for the entire city. A correlation analysis was performed for three different periods in the day established as follows (24:00-03:00-06:00, 09:00-12:00-15:00 and 15:00-18:00-21:00). Subsequently, a linear regression analysis was performed by time period. The results showed a higher positive correlation between ozone concentration and temperature from 15:00 hrs to 21:00 hrs; likewise, this period showed a higher goodness of fit in the ozone prediction (R2=0.99; RMSE: 1.12 ppbv). Temperature allows spatial prediction of ozone concentrations in urban areas with acceptable accuracy.

: Background: Vaccine-related death is one of the leading causes of death among African Children. Vaccine coverage is a very important measure to decrease infant mortality. Covid-19 Pandemic has affected the healthcare system and may have disrupted vaccine coverage. Methods: DTP third doses (DTP3) Vaccine Coverage was extracted from UNICEF databases from 2012 to 2021( the last available date). Joinpoint regression was performed to detect the point where the trend changed. The annual percentage change (APC) with 95% confidence intervals (95% CI) was calculated for Africa and the regions. We compared DTP3 vaccination coverage in 2019 with 2021 in each country to verify compliance with WHO targets. Result: During the whole period, the vaccine coverage in Africa has increased with an Annual Percent change of 1.2% (IC 95% 0.9-1.5): We detected one Joint point in 2019. In 2019-2021, there was a decrease in DTP3 coverage with an APC of -3.5(95% -6.0;-0,9). (P< 0.001). Vaccination rates have decreased in many regions and countries during the last two years. Conclusions. COVID-19 has disrupted vaccine coverage, decreasing it all over Africa.

Wheat and barley are among the primary food resources of the world population; therefore, their growth and observation are essential in farms to enhance food security worldwide. On top of that, careful observation of the product is essential to find solutions for the issues faced during their production and to reduce the impacts of weather changes. With the advancement of Remote Sensing technology, the observation and estimation process has increased. In this study, numbers of spectral vegetation indices was used along with canopy biophysical properties ( LAI ) and biochemical properties (chlorophyll), there calculated from (Landsat 8 and Sentinel-2) satellite data. The wheat and barley samples were collected before were be ready for harvest, and a relation with the vegetarian indices was established using the Multi-Linear Regression module, in which the equations used in predicting the harvest were developed and used to create a graph for expected harvest. The result indicated that there is a strong relationship between the vegetation indices of Sentinel-2 and Landsat images and the actual grain yield with R² of 0.77 and 0.71, respectively. The results show that the strongest correlation is observed between the LAI data obtained from Sentinel data and cereal yield data, with an R² 0.68, and the highest correlation for the indices of Landsat images is observed in the NDWI with R² 0.59 and the lowest degree of error was in the root mean square error (RMSE) for the Sentinel-2 and Landsat 8 with 0.57 and 1.54. In addition, this study also showed that the least relationship for grain yield prediction was observed between the NDRI for Sentinel-2 (R² 0.1) and SAVI for Landsat image (R² 0.47).

To investigate the dynamics of land surface temperature (LST) in Afghanistan in the period 2000-2021 and to assess the impact of such factors as soil moisture, precipitation, and vegetation coverage on it, remotely sensed soil moisture data from Land Data Assimilation System (FLDAS), precipitation data from Climate Hazards Group Infra-Red Precipitation with Station (CHIRPS), and NDVI and LST from Moderate Resolution Imaging Spectroradiometer (MODIS) were downloaded and correlations between them were analyzed using the regression method. The result shows that the LST in Afghanistan has a slightly decreasing, but insignificant trend during the study period (R=0.2, p-value=0.25), while vegetation coverage, precipitation, and soil moisture had an increasing trend. It was revealed that soil moisture has the highest impact on LST (R=0.7, p-value=0.0007), and the soil moisture, precipitation, and vegetation coverage explain almost 80% of spring (R2=0.73) and summer (R2=0.76) LST variability in Afghanistan. The LST variability analysis done separately for Afghanistan’s rivers subbasins shows that the LST of the Amu Darya subbasin had an upward trend in the study period, while for the Kabul subbasin the trend was downward.

Alphaviruses, flaviviruses, measles viruses and rhabdoviruses are enveloped single-stranded RNA viruses, which have been engineered as expression vector systems for recombinant protein expression and vaccine development. Due to the presence of non-structural genes encoding the replicase complex, a 200,000-fold amplification of viral RNA occurs in the cytoplasm of infected cells providing extreme transgene expression levels, which is why they are named self-replicating RNA viruses. Expression of surface proteins of pathogens causing infectious disease and tumor antigens provide the basis for vaccine development against infectious diseases and cancer. The self-replicating RNA viral vectors can be administered as replicon RNA, recombinant viral particles, or layered DNA/RNA replicons. Self-replicating RNA viral vectors have been applied for vaccine development against influenza virus, HIV, hepatitis B virus, human papilloma virus, Ebola virus and recently coronaviruses, especially SARS-CoV-2 the causative agent of the COVID-19 pandemic. Measles virus and rhabdovirus vector-based SARS-CoV-2 vaccine candidates have been subjected to clinical trials. Moreover, RNA vaccine candidates based on self-amplifying alphaviruses have also been evaluated in clinical settings. Various cancers such as brain, breast, lung, ovarian, prostate cancer and melanoma have also been targeted for vaccine development. Robust immune responses and protection have been demonstrated in animal models. Clinical trials have shown good safety and target-specific immune responses. Ervebo, the VSV-based vaccine against Ebola virus disease has been approved for human use.

Indian cities are increasingly becoming susceptible to PM10 induced health effects which have become a matter of concern for the policymakers of the country. Air pollution is engulfing the comparatively smaller cities as the rapid pace of urbanization, and economic development seems not to lose steam ever. A review of air pollution of 28 cities of India, which includes tier-I, II, and III cities of India, found to have grossly violated both WHO and NAAQS standards in respect of acceptable daily average PM10 concentrations by a wide margin. Predicting the city level PM10 concentrations in advance and accordingly initiate prior actions is an acceptable solution to save the city dwellers from PM10 induced health hazards. Predictive ability of three models, linear MLR, nonlinear MLP (ANN), and nonlinear CART, for one day ahead PM10 concentration forecasting of tier-II Guwahati city, were tested with 2016-2018 daily average observed climate data, PM10, and gaseous pollutants. The results show that the non-linear algorithm MLP with feedforward backpropagation network topologies of ANN class, giving the best prediction value when compared with linear MLR and nonlinear CART model. ANN (MLP) approach, therefore, may be useful to effectively derive a predictive understanding of one day ahead PM10 concentration level and thus provide a tool to the policymakers for improving decision-making associated with air pollution and public health.

Soil quality assessment based on crop yields and identification of key indicators of it can be used for better management of agricultural production. In the current research, the weighted additive soil quality index (SQIw), factor analysis (FA) and multiple linear regression (MLR) method are used to assess the soil quality of rainfed winter wheat fields with two soil orders on 53.20 km2 of agricultural land in western Iran. A total of 18 soil quality indicators were determined for 100 soil samples (0-20 cm depth) from two soil orders (Inceptisols and Entisols). The soil properties measured were: pH, soil texture, organic carbon (OC), cation exchange capacity (CEC), electrical conductivity (EC), soil microbial respiration (SMR), carbonate calcium equivalent (CCE), soil porosity (SP), bulk density (BD), exchangeable sodium percentage (ESP), mean weight diameter (MWD), available potassium (AK), total nitrogen (TN), available phosphorus (AP), available Fe (AFe), available Zn (AZn), available Mn (AMn), and available Cu (ACu). Mean wheat grain yield for the two years for all of the 100 sampling sites was also gathered. The SQIw was calculated using two weighting methods (FA and MLR) and maps were created using a digital soil mapping framework. The soil indicators taken in the minimum data set (MDS) were AK, clay, CEC, AP, SMR, and sand. The correlation between the MLR weighting technique (SQI-M) and the rainfed wheat yield (r=0.62) was slightly larger than that the correlation of yield with the FA weighted technique (SQI-F) (r=0.58). Results showed that the means of both SQI-M and SQI-F and rainfed wheat yield for Inceptisols were higher than for Entisols although these differences were not statistically significant. Both SQI-M and SQI-F showed that areas with Entisols had lower proportions of good soil quality grades (Grade I and II), and higher proportions of poor soil quality grades (Grade IV and V) compared to Inceptisols. Based on these results, soil type must be considered for soil quality assessment in future studies to maintain and enhance soil quality and sustainable production. The overall soil quality of the study region was of poor and moderate grades. To improve soil quality, it is therefore recommended that effective practices such as the implementation of scientific integrated nutrient management involving the combined use of organic and inorganic fertilizers in rainfed wheat fields be promoted.

This study investigates the trend in monthly and annual rainfall, minimum and maximum temperature (T_min and T_max) using the Mann–Kendall (MK) test and Sen’s slope (SS) method and evaluates the significance of their variability for maize, sorghum and millet yields in northern Togo employing multiple regression analysis. The historical data of Kara, Niamtougou, Mango and Dapaong weather stations from 1977 to 2012 were used. Four non-parametric methods—Alexandersson’s Standard Normal Homogeneity Test (SNHT), Buishand’s Range Test (BRT), Pettitt’s Test (PT) and Von Neumann’s Ratio Test (VNRT)—were applied to detect homogeneity in the data. For the data which were serially correlated, a modified version of the MK test (pre-whitening) was utilised. Results showed an increasing trend in the annual rainfall in all four locations. However, this trend was only significant at Dapaong (p < 0.1). There was an increasing trend in T_max at Kara, Mango and Niamtougou, unlike Dapaong where T_max revealed a significant decreasing trend (p < 0.01). Similarly, there was an increasing trend in T_min at Kara, Mango and Dapaong, unlike Niamtougou where T_min showed a non-significant decreasing trend (p > 0.05). Rainfall in Dapaong was found to have increased (7.79 mm/year) more than the other locations such as Kara (2.20 mm/year), Niamtougou (4.57 mm/year) and Mango (0.67 mm). T_max increased by 0.13, 0.13 and 0.32 °C per decade at Kara, Niamtougou and Mango, respectively, and decreased by 0.20 per decade in Dapaong. Likewise, T_min increased by 0.07, 0.20 and 0.02 °C per decade at Kara, Mango and Dapaong, respectively, and decreased by 0.01 °C per decade at Niamtougou. Results of multiple regression analysis revealed nonlinear yield responses to changes in rainfall and temperature. Rainfall and temperature variability affects rainfed cereal crops production, but the effects vary across crops. The temperature has a positive effect on maize yield in Kara, Niamtougou and Mango but a negative effect on sorghum in Niamtougou and millet in Dapaong, while rainfall has a negative effect on maize yield in Niamtougou and Dapaong and millet yield in Mango. In all locations, rainfall and temperature variability has a significant effect on the cereal crop yields. There is, therefore, a need to adopt some adaptation strategies for sustainable agricultural production in northern Togo.