Abstract: The Inconel 625 is a nickel-based alloy has been widely used in the high-temperature application. The Inconel 625 exhibits unstable plastic flow at elevated temperature characterized by serrated yielding, known as Portevin-Le Chatelier effect. The aim of this work is to evaluate the mechanical properties at high temperatures of the Inconel 625. The tensile tests were performed in the temperature range of room temperature until 1000 °C and strain rate of 2x10^-4 to 2x10^-3 s^-1. The creep tests were performed in the temperature range of 600-700 °C, in the stress range of 500-600 MPa in a constant load mode. The surface fracture was observed by optical and scanning electron microscopy. Serrated stress-strain behavior was observed in the curves obtained at 200 to 700 °C, which was associated with the dynamic strain aging effect. The yield strength and the elongation values show an anomalous behavior as a function of the test temperature. An intergranular cracking was observed specimen tensile tested at 500 °C that can be attributed to the decohesion of the carbides along the grain boundaries. The fracture surface of the specimen tensile tested at 700 °C showed the predominance of transgranular cracking with tear dimples with a parabolic shape.

Typhoid fever is a communicable disease transmitted by the bacteria Salmonella typhi, related to serotype paratyphi A, B and C. The disease is of a significant health concern in most developing countries especially Cameroon. Objectives: The study aimed at determining the prevalence and associated risk factors of typhoid fever in children ( 0-18 years) attending the “Deo Gratias” hospital in Douala. Method: A hospital base cross sectional study from August to September 2018 was carried out in patients’ age 0-18 years suffering from typhoid fever at the Deo gratias Catholic hospital. Widal slide agglutination test was the diagnostic test used. Positive tested patients were administered questionnaires to evaluate the level of knowledge, attitude and practice toward the disease, as well as their self-management abilities. Data obtained from respondents was analysed by descriptive statistics. One-way ANOVA and means comparison using Tukey’s test (α = 0.05) was performed to check whether the population of respondents differed significantly across risk factor practices. Results were finally presented on bar charts, tables and pie chart. Results: Typhoid fever was more prevalent in females (52.3%) than in males (47.7%), with a high proportion in the ages 5-9 years (38.6%). A significant difference was observed in population of respondents across risk factor practices. Conclusion: Water quality have a great impact on the burden of typhoid fever among children. The identification of risk factors associated to the disease is of great importance in the development of rational control strategies of the disease.

Multiple studies reported a negative relationship between the Honesty-Humility factor of the HEXACO model and psychopathy. The Durand Adaptive Psychopathic Traits Questionnaire (DAPTQ), which was developed to assess adaptive traits known to be related to psychopathic traits, has previously demonstrate positive relationships with all factors of the Big Five Model, at the exception of a negative relationship with neuroticism. The current study aims to validate the previously reported association between the DAPTQ and the five major components of the personality, while also examining its relationship with the Honesty-Humility factor as defined by the HEXACO model. The results (N = 171) support the good internal consistency, two weeks test-retest validity and inter-correlation of the DAPTQ. A Confirmatory Factor Analysis further supports the nine-factor model of the DAPTQ. When compared to the HEXACO, the DAPTQ did not display any relationship with the Honesty-Humility factor, nor the Agreeableness and Openness factors, but kept its similar association to Emotionality, Extroversion, and Conscientiousness as initially reported in its development phase. Overall, the results support the discriminant validity of the DAPTQ to assess adaptive traits related to the psychopathic personality without overlapping with psychopathic personality traits. Results are discussed in terms of implications and further improvements to validate the DAPTQ.

The importance of statistics in biological research is inevitable. The appliance of statistics is the most powerful tool to support the scientific hypothesis and to give credibility to biological research methodology, to interpret convoluted explanations and conclusions based on the research findings. The evidences from literatures point the persistent statistical errors, selection of non-proper statistical test with the consequence of misinterpretation of the scientific results which are published in international journals. One of the most extensively used statistical tests in the field of biology (preclinical and clinical) is analysis of variance (ANOVA). ANOVA test is in place of multiple T-tests to compare the means of more than two groups at a time; and there are some important points which biologists should be aware of them to avoid possible misinterpretation of results with the consequence of wrong conclusion. Accordingly, the aim of the current review is to help biologists to understand the basic concepts of ANOVA test and reach to a more valid interpretation of achieved results.

Reliable methods to confirm the diagnosis of COVID-19 are essential to the successful management and containment of the virus. Current diagnostic options are limited in type, supply, and reliability. This article explores the controversial unreliability of existing diagnostic methods and maintains that more reliable diagnostic methods, combinations, and sequencing are necessary to effectively assist in reducing the occurrence of discharge of the patient on false negative test results. This reduction would in effect reduce transmission of the disease.

Global differences in changes in the numbers of population-adjusted daily test-positive cases (NPDP) and deaths (NPDD) by COVID-19 were analyzed for 49 countries, including developed and developing countries. The changes as a proportion of national population were compared, adjusting by the beginning of test-positive cases increase (BPI) or deaths increase (BDI). Remarkable regional differences of more than 100 fold in NPDP and NPDD were observed. The trajectories of NPDD after BDI increased exponentially within 20 days in most countries. Machine learning analysis suggested that NPDD on 30 days after BDI was the highest in developed Western countries (1180 persons per hundred million), followed by countries in the Middle East (128), Latin America (97), and Asia (7). Furthermore, in Western countries with positive rates of the PCR test of less than 7.0%, the increase in NPDP was slowing-down two weeks after BPI, and subsequent NPDD was only 15% compared with those with higher positive rates, which suggested that the situation of testing might have affected the velocity of COVID-19 spread. The causes behind remarkable differences between regions possibly include genetic factors of inhabitants because distributions of the race and of the observed infection increasing rates were in good agreement globally.

Quantifying the landscape pattern change can effectively demonstrate the ecological progresses and the consequences of urbanization. Based on remotely sensed land cover data in 1994, 2000, 2006 and a gradient analysis with landscape metrics at landscape- and class- level, we attempted to characterize the individual and entire landscape patterns of Shanghai metropolitan during the rapid urbanization. We highlighted that a roadscape transect approach that combined the buffer zone method and the transect-based approach was introduced to describe the urban-rural patterns of agricultural, residential, green, industrial, and public facilities land along the railway route. Our results of landscape metrics showed significant spatiotemporal patterns and gradient variations along the transect. The urban growth pattern in two time spans conform to the hypothesis for diffusion–coalescence processes, implying that the railway is adaptive as a gradient element to analyze the landscape patterns with urbanization. As the natural landscape was replaced by urban landscape gradually, the urban fringe expanded radically. The results also showed that the desakota region expanded its extent widely. Satellite towns witnessed the continual transformation from the predominantly rural landscape to peri-urban landscape. Furthermore, the gap between urban and rural areas remained large especially in public service. More reasonable urban plans and land use policies should push to make more of an effort to transition from the urban-rural separation to coordinated urban-rural development. This study is a meaningful trial in demonstrating a new form of urban–rural transects to study the landscape change of large cities from a strategic viewpoint. By combining gradient analysis with landscape metrics, we addressed the process of urbanization both spatially and temporally, and provided a more quantitative approach to urban studies.

Impact characterization of linear resonant actuator (LRA) is studied experimentally by newly developed drop tester, which can control various experimental uncertainty such as rotational moment, air resistance, secondary impact and so on. The feasibility of this test apparatus was verified by comparison with free fall test. By utilizing a high-speed camera and measuring the vibrational displacement of spring material, the impact behavior was captured and the damping ratio of the system was defined. Based on the above processes, the finite element model was established and the experimental and analytical results were successfully correlated. Finally, the damage of the system from impact loading can be expected by developed model and as a result, this research can improve the impact reliability of LRA.

Abstract: This paper is focusing on the stabilisation of soil using jute fibre as soil stabilizer. Stabilisation is the process of modifying the properties of a soil to improve its engineering performance and used it for a variety of engineering works. This study examines the potential of soil stabilization with jute fibre when it is cut into roughly 30mm lengths as stabilizer. The varying percentages like 0.5%, 1%, 1.5 and 2% of pieces of jute fibre were used and mixed it with soil. The laboratory tests such as California Bearing Ratio (CBR) test, modified compaction tests and direct shear strength tests have been conducted to observe the change in engineering properties of soil. On the basis of the experiments performed, it can be concluded that the stabilization of soil using 30mm pieces of jute as stabilizer improves the strength characteristics of the soil so that it becomes usable as one of the reinforcing material for the construction of roadways, parking areas, site development projects, airports and many other situations where sub-soils are not suitable for construction.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

While texturing of workpiece surfaces to promote lubrication in metal forming has been applied for several decades tool surface texturing is rather new. In the present paper tool texturing is studied as a method to prevent galling. Adopting a strip reduction test longitudinal pocket geometries oriented perpendicular to the sliding direction, with shallow pocket depth, small pocket angle to the workpiece surface and varying distance between pockets are investigated. The experiments reveal that the distance between pockets should be larger than the pocket width thereby creating a topography similar to flat table mountains to avoid mechanical interlocking in the valleys; otherwise an increase in drawing load and pick-up on the tools is observed. The textured tool surface lowers friction and improves lubrication performance provided that the distance between pockets is 2-4 times larger than the pocket width. Larger drawing speed facilitates escape of the entrapped lubricant in the pockets. Testing with low to medium viscosity oils leads to a low sheet roughness on the plateaus but also local workpiece material pick-up on the tool plateaus. Large lubricant viscosity results in higher sheet plateau roughness but also prevents pick-up and galling.

Exposure to malachite green (MG) may pose great health risks to humans, thus it is of prime importance to develop fast and robust methods to quantitatively screen the presence malachite green in environment. Herein application of extractive electrospray ionization mass spectrometry (EESI-MS) has been extended to the trace detection of MG within lake water and aquiculture water, due to the intensive use of MG as biocide in fisheries. This method has the advantage of obviating offline liquid-liquid extraction or tedious matrix separation prior to the measurement of malachite green in native aqueous medium. The experimental results indicate that the extrapolated detection limit for MG was ~3.8 ug L-1 (S/N=3) in lake water samples and ~ 0.5 ug L-1 in ultrapure water under optimized experimental conditions. The signal intensity of MG showed good linearity over the concentration range of 10–5000 ug L-1. Measurement of practical water samples fortified with MG at 0.01 and 0.1 mg L-1 gave a good validation of the established calibration curve. The average recoveries of malachite green in lake water and Carassius carassius fish farm effluent water were 114.9% (6.6% RSD) and 85.4% (9.2% RSD), respectively. Overall, the established EESI-MS/MS method has been demonstrated suitable for sensitive and rapid (<2 min per sample) quantitative detection of malachite green in various aqueous media, indicating its potential for online real-time monitoring of real life samples.

The Combined Elevation Test (CET) is a musculoskeletal screening technique (MST) replicates the streamline position in swimming and is commonly used in various sports. Although the CET is widely used, no normative data exist within an adolescent population. Therefore, the purpose of this study was to develop a normative data set for the CET within an adolescent population and to evaluate the influence various demographic and anthropometric variables. Data was collected for 416 participants aged between 8 and 18 years old. Age and arm span showed a significant correlation with CET scores (arm span r_s (105) = .478, p = .000, age r_s (416) = .238 p = .000). Regression analysis further quantified the influence of arm span and age on CET scores accounting for 23.1% and 5.3% of variability respectively. These results can be used as a reference point for clinicians and coaches who are using the CET within their assessment.

Theory of the Thermal Response Testing (TRT) is a well-known part of sizing process of the geothermal exchange system. Multiple parameters influence accuracy of effective ground thermal conductivity measurement; like testing time, variable power, climate interferences, groundwater effect etc. To improve accuracy of the TRT we introduced procedure to additionally analyze falloff temperature decline after power test. Method is based on a premise of analogy between TRT and petroleum well testing, since origin of both procedures lies in diffusivity equation with solutions for heat conduction or pressure analysis during radial flow. Applying pressure build-up test interpretation technique to the borehole heat exchanger testing, greater accuracy could be achieved since ground conductivity could be obtained from this period. Analysis was conducted on coaxial exchanger with five different power steps, and with both direct and reverse flow regime. Each test was set with 96hr of a classical TRT, followed by 96hr of temperature decline, making it almost 2000 hours of cumulative borehole testing. Results showed that ground conductivity value could vary as much as 25% depending on test time, seasonal period and power fluctuations while thermal conductivity obtained from a falloff period gives more stable values with only 10% value variation.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

Sleep is still considered a mystery, despite intense scientific investigation. Here we present the first complete biological theory of sleep. The role of sleep is to restore the optimal homeostatic state, which is essential for tissue performance and health. Non-rapid eye movement sleep (NREMS) restores cortical and most other brain neurons, via relaxed global activity managed by thalamocortical circuits. The role of REM sleep is to restore acetylcholine (ACh) neurons, which support focused responses and hence cannot participate in global oscillations. Sleep enhances learning and memory via state restoration and ACh-affected paths. NREMS induces a lack of consciousness because global synchronous activity prevents focused responses, which are essential for consciousness. Dreams result from focused neural firing during sharp-wave ripples and REMS, and have a sense of reality because they involve the same neurons representing focused perceptual responses during wake. Anesthetics utilize a variety of mechanisms that prevent focused responses.

Optical fiber measurement systems have recently gained popularity following a multitude of intensive investigations. A new technique has been developed for these measurement systems that uses Rayleigh backscatter to determine the distributed strain measurement over the total length of a fiber. These measurement systems have great potential in civil engineering and structural health monitoring. This paper addresses some preliminary comparisons between three different fiber coatings and six different adhesives on steel structures. The results are based on a bending test with specimens made of precision flat steel; optical fiber strain measurements were compared with photogrammetric strain measurements. Analysis of the test data showed a strong correlation between the optical measurement system’s results and the theoretical results up to the yielding point of the steel. Furthermore, the results indicate that fibers with the Ormocer® and polyimide coatings have almost no loss in the strain measurements. The main results of this investigation are a guideline describing how to attach optical fibers to steel surfaces for distributed fiber optical strain measurements and recommendations for coatings to obtain realistic strain values. Additionally, the advantages of distributed strain measurements were revealed, which illustrates the potential of Rayleigh backscattering applications.

Outbreaks of coronavirus disease 2019 (COVID-19) have been recorded in different countries across the globe. The virus is highly contagious, hence early detection, isolation, and quarantine of infected patients will play an important role in containing the viral spread. Diagnosis in a mobile lab can aid to find infected patients in time. Here, we develop a field-deployable diagnostic workflow that can reliably detect COVID-19. Instruments used in this workflow could easily fit in a mobile cabin hospital and also be installed in the community. Different steps from sample inactivation to detection were optimized to find the fastest steps and portable instruments in detection of COVID-19. Each step was compared to that of the normal laboratory diagnosis set-up. From the results, our proposed workflow (80 min) was two times faster compared to that of the normal laboratory workflow (183 min) and a maximum of 32 samples could be detected at each run. Additionally, we showed that using 1% Rewocid WK-30 could inactivate the novel coronavirus directly without affecting the overall detection results. Comparison of our workflow using an in-house assay to that of a commercially acquired assay produced highly reliable results. From the 250 hospital samples tested, there was a high concordance 247/250 (98.8%) between the two assays. The in-house assay sensitivity and specificity were 116/116 (100%) and 131/134 (97.8%) compared to that of the commercial assay. Based on these results, we believe that our workflow is fast, reliable, adaptable and most importantly, field deployable.

Full-scale/model test comparison studies to validate the traditional ABL wind tunnel simulation technique are reviewed. According to the literature review, notable discrepancies between full-scale measurement results and model test results were observed by most performed comparison studies, but the causes of the observed discrepancies were not revealed in a scientific way by those studies. In this regard, a new research scheme for future full-scale/model test comparison studies is proposed in this article, which utilizes the multiple-fan actively controlled wind tunnel simulation technique. With the new research scheme, future full-scale/model test comparison studies are expected to reasonably disclose the main problems with the traditional ABL wind tunnel simulation technique, and the technique can be improved correspondingly.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

Disposable absorbent hygiene products have evolved for superior performance, enhancing the convenience of daily lives. Yet the use of disposable hygiene pads has brought safety concerns on chemical exposure, and significant efforts have been made to assess the potential risks associated with use of hygiene pads. This article intends to overview the safety assessment framework of diapers and feminine pads, which includes hazard identification, hazard characterization, exposure assessment, risk characterization, and postmarket risk management. Risk assessment of various constituents are reviewed for quantification methods and conservative estimation of exposure parameters. By reviewing the up-to-date considerations in risk assessment, we aim to provide insightful discussion on safety evaluation of current versions of disposable absorbent products. More clinical testing and postmarket surveillance are needed for continuous monitoring of potential health impacts of advanced products and constituents.

Abstract Introduction: Visual perceptual skills are essential for independent participation in self-care tasks, educational, work and leisure time activities. The effect of HIV on the visual perceptual skills is not well understood among children in low resource settings like Zimbabwe. Methods: A cross sectional comparative study was done with 30 children living with HIV and 30 children living without HIV residing in Harare urban area. The TVPS-3 was used to assess their visual perceptual skills. SPSS version 22, STATISTICA 13 and Microsoft 2016 were used for data analysis. Results: Both groups of children had mean percentile ranks below 50 on their TVPS-3 scores. Children without HIV generally performed better than those with HIV but the difference was not statistically significant in most cases. Through univariate analysis, only performance on Spatial Relations significantly differed between the two groups. Both groups had lowest scores in Basic visual perceptual skills. Age and school grade were the independent predictors of the children’s performances in the study. Conclusion: There is need for Occupational therapy services in public primary schools and in the pediatric Opportunistic Infections clinics in hospitals to be part of the health team which caters for children with visual perceptual challenges.

Within the field of guilt and shame, two competing perspectives have been advanced. The first, the social-adaptive perspective, proposes that guilt is an inherently adaptive emotion and shame is an inherently maladaptive emotion; thus, those interested in moral character development and psychopathology should work to increase an individual’s guilt-proneness and decrease an individual’s shame-proneness. The functionalist perspective, in contrast, argues that both guilt and shame can serve a person adaptively or maladaptively—depending on the situational appropriateness, duration, intensity, and so forth. This paper reviews the research conducted supporting both positions, critiques some issues with the most widely used guilt- and shame-proneness measure in the social-adaptive research (the TOSCA), and discusses the differences in results found when assessing guilt and shame at the state versus trait level. The conclusion drawn is that although there is broad support for the functionalist perspective across a wide variety of state and trait guilt/shame studies, the functionalist perspective does not yet have the wealth of data supporting it that has been generated by the social-adaptive perspective using the TOSCA. Thus, before a dominant perspective can be identified, researchers need to (1) do more research assessing how the social-adaptive perspective compares to the functionalist perspective at the state level, and (2) do more trait research within the functionalist perspective to compare functionalist guilt- and shame-proneness measures with the TOSCA.

We are witnessing the severe third outbreak mediated by coronaviruses affecting global public health with unprecedented economic consequences. A better understanding of its phylogenetics, exploration of sequence features and mutational changes could unveil its genealogy to gain insights into the mechanism of transmission and development of possible interventions. Our comparative genomic analyses of >160 isolates of SARS-CoV-2 reveal phylogenetic kinship with other coronaviruses and emergence of evolutionary divergence in clinical isolates. t-SNE-based clustering revealed different clades but no continent specific clusters. Amino acid substitutions at RBD of spike protein provide possible reasons for rapid transmission. Few proteins specific to SARS-CoV-2 were identified which could have implications as therapeutic targets and diagnostic biomarkers. Virtual screening identified repurposed drugs, known nutraceuticals, for specific interventions. These phylogenetic observations reveal the ancestry and computational studies reveal the emergency measures to interject this emerging pathogen that pose threat to whole of mankind.

In the European Union, the demand for polyurethane is continually growing. In 2017, the estimated production value of polyurethane was 700,400T, of which 27.3% is taken to landfill, which causes an environmental problem. In this paper the behaviour of various polyurethane foams from the waste of different types of industries will be analysed with the aim of assessing their potential use in construction materials. In order to this, the wastes were chemically tested by means of CHNS, TGA, and leaching tests. They were tested microstructurally by means of SEM. The processing parameters of the waste was calculated after finding out its granulometry and its physical properties i.e. density and water absorption capacity. In addition, the possibility of incorporating these wastes in plaster matrices was studied by determining its rendering in an operational context, finding out its mechanical resistance to flexion and compression at 7 days, its reaction to fire as well as its weight per unit of area and its thermal behaviour. The results show that in all cases, the waste is inert and does not undergo leaching. The generation process of the waste determines the foam’s microstructure in addition to its physical-chemical properties that directly affect building materials in which they are included, thus offering different ways in which they can be applied.

An on-site, ultra-sensitive, and quantitative sensing method was developed based on quantum dot nanobeads (QDNBs) and test strip for the determination of total aflatoxins (AFTs) in rice and peanut. The monoclonal antibody against AFT (mAbAFT) was home-made and labeled with QDNB. After the pre-coating of the AFT antigen on the test line (T line), the competitive immunoreactions were conducted between AFT and AFT antigen on the T line with QDNBs-mAbAFT. Under optimal conditions, this approach allowed a rapid response towards AFT with a considerable sensitivity of 1.4 pg/mL and 2.9 pg/mL in rice and peanut matrices, respectively. The put-in and put-out duration were within 10 min. The recoveries for AFT in rice and peanut samples matrices were recorded from 86.25–118.0% with the relative deviations (RSD) below 12%. The assay was further validated via the comparison between this QDNB strip and the conventional HPLC method using spiked samples. Thus, the design provided a potential alternative for on-site, ultra-sensitive, and quantitative sensing of AFT that could also be expanded to other chemical contaminants for food safety.

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

The stability assessment of aged tunnel linings were mainly evaluated based on the visual inspection, and the Tunnel-lining Crack Index (TCI) is one of the most widely used tunnel lining health assessment indexes in Japan. However, the intersection and distribution of cracks, which can influence the stability of tunnel lining greatly, were not considered in the TCI. A new method was proposed for the health assessment of tunnel lining, which evaluate the lining states according to the fractal dimension of cracks. Based on the machine vision-based method, the crack image can be extracted efficiently. The fractal dimension of lining cracks in one span can be obtained in a few minutes. A series of comparative tests and field tests were conducted to evaluate the validity of this new method. The comparative tests confirmed that fractal dimension can characterize the density, width, and distribution of cracks. The results also certificated that the influence of crack width is larger than the crack density. The intersection of cracks, which will increase the risk of lining collapse, can also increase the fractal dimension, whereas the TCI keep constant. The fractal dimensions of tunnel lining cracks were obtained according to the digital inspection test of Hidake Tunnel in Japan for all the 65 spans. Moreover, the TCI was obtained through statistical methods. The correlation between fractal dimension and TCI of tunnel lining was studied. The significance of the new evaluation index is that it can identify some unusual spans of tunnel lining and provide a basis for further internal testing. As a complement to the conventional visual inspection method, the fractal dimension of the cracks is a promising health assessment index.

: Nanotechnology options to road surface maintenance offers several advantages compared to traditionally used materials. The small particle sizer of hydrophobic Nano-Silane modified Nano-Polymers (NSNP) enables these nanotechnology products to deeply penetrate existing road surfaces, sealing micro-cracks and render surfacings to be water-resistant for extended periods of time. In comparison, traditionally used products contain minimum partial sizes of about 1 – 5 microns, that provide a superficial protection that wears off in a relatively short period of time. These traditional products are often associated with vehicle contamination while drying and requires the re-instatement of road markings. None of these disadvantages are associated with applicable NSNP technologies that are quick drying, with no vehicle contamination risks and is equivalent to a “clear-seal” requiring no reinstatement of road markings. In a similar vein, pot-hole repairs can be done using applicable, easy to use, pre-packed and treated pot-hole repair kits that are water-repellent and quick-drying at a fraction of the costs of conventional cold-mix products. Resurfacing using NME binder slurries can be done labour-intensively on a pre-treated NSNP surfacing, restoring cracked surfacing and providing a water-resistant long-lasting protective layer without the removal of existing cracked areas. The implementation of nanotechnology solutions for road surface maintenance operations is directly associated with ease of use, labour-intensive operations, prevention of considerable deterioration in riding quality due to removal and manual re-instatement of cracked surfaces, time and cost savings and a reduction in the risk of water damage to the sub-structure. TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

Co-integration and Causality was built to conduct studies on causality relation between carbon intensity and coal consumption leading to providing important basis for the transition to a low carbon economy. The EG two-step method was performed to study the relation between carbon intensity and coal consumption of China during 1990-2015 and the co-integration and Granger test was constructed to build up the co-integration and error correction models for analysis of the interaction between carbon intensity and coal consumption. The results showed that in long term there is a stable co-integration relation and a positive correlation between carbon intensity and coal consumption; whereas fluctuations exist in short term and there is a one-way Granger causality of carbon intensity with respect to coal consumption.

The scratch test consists in pushing a tool across the surface of a material at a given penetration depth or applied load. It has several applications in Science and Engineering including strength testing, damage and quality control of thin films and coatings. Despite numerous attempts in scientific literature, the application of scratch test to characterizations of fracture properties remains a heavily controversial topic. Therefore, this investigation arises as an experimental study in order to assess the fracture toughness using scratch test. A study on the effect of cryogenic treatment, performed after tempering, on fracture toughness, via scratch test experiments, of different tool steels has been made. A laboratory investigation on AISI D2, AISI M2 and X105CrCoMo18 steel confirms the possibility of increasing the fracture toughness by carrying out the cryogenic treatment after the usual heat treatment

4-(thiazol-2-yldiazenyl)phenol (L₁) and 2-((4-hydroxyphenyl) diazenyl)-5-nitrophenol (L₂) based on azo phenol were synthesised and used as selective colorimetric sensor for CN^- and AcO⁻ ion in DMSO/H₂O-HEPES (v/v; 1:1, pH–7.3 ± 0.2) and showed good sensitivity with large red shifts and nanomolar detection limit for CN^- and AcO^- ion. The stoichiometry of L₁ with CN⁻/AcO⁻ ion was found to be 1:1 and L₂ with CN⁻/AcO⁻ ion was found to be 1:2. Binding constant for L₁+ CN⁻, L₁ + AcO⁻, L₂ + CN⁻ and L₂ + AcO⁻ were calculated by B-H plot as 1.6 × 10³, 8.0 × 10², 8.4 × 10³ and 1.7 × 10² respectively. L₂ showed high selectivity towards CN⁻ ion with low detection limit of 81 nM and large binding constant. In addition, ¹H NMR titration and DFT studies also supported the deprotonation mechanism of receptors in the presence of selective anions.

Simultaneous measurement of different substances from a single sample is an emerging issue to achieve efficient and high-throughput detection in several fields of application. Although immunoanalytical techniques have well-established and prevailing advantages over alternative screening analytical platforms, one of the incoming challenges for immunoassay is exactly multiplexing. The Lateral Flow Immunoassay (LFIA) is a leading immunoanalytical technique for onsite analysis thanks to its simplicity, rapidity and cost-effectiveness. Moreover, LFIA architecture is adaptable to multiplexing and therefore candidates as a possible answer to the pressing demand of multiplexing point-of-need analysis. The review present an overview of diverse approaches for multiplex LFIA, with a special focus on strategies based on new types of magnetic, fluorescent and colored labels

The performance of ground heat exchangers systems depends on the knowledge of the thermal parameters of the ground like thermal conductivity, thermal capacity and diffusivity. The knowledge of these parameters often requires quite accurate experimental analysis, known under the name of Thermal Response Test (TRT). In this paper, after a general analysis of the various available types of TRT and the study of the theoretical basics of the method, the perspective of the definition of a simplified routine method of analysis based on the combination of a particular version of TRT and the routine geotechnical tests for the characterization of soil stratigraphy and of the ground characteristics, mandatory before the construction of a new buildings, even if limited to quite short drilling depth (lower than 30 m). The idea of developing TRT in connection with geotechnical test activity has the objective of promoting a widespread use of in-situ experimental analysis and of reducing TRT costs and time duration of the experimental analysis. The considerations exposed in the present paper lead to reconsider a particular variety of the TRT in particular the version known as Thermal Response Test while Drilling (TRTWD).

Signal-to-noise ratio (SNR) is an important index to evaluate radiation performance and image quality of optical imaging systems under low illumination background. Under the nighttime lighting condition, the illumination of remote sensing objects is low and varies greatly, usually ranging from several lux to tens of thousands of lux. Nighttime light remote sensing imaging requires high sensitivity and large dynamic range of detectors. Luojia 1-01 is the first professional nighttime light remote sensing satellite in the world. In this paper, we took the nighttime light remote sensing camera carried on the satellite as research object, proposed an in-orbit SNR test method based on time series images to overcome the problem of low spatial resolution. We first analyzed the process of luminous flux transmission between objects and satellite and established a radiative transfer model. By combining the parameters of large relative aperture optical system and high sensitivity CMOS device, we established SNR model and specially analyzed the effect of exposure time and quantization bits on SNR. Finally we used the proposed in-orbit test method to calculate SNR of lighting images acquired by satellite. And the measured result is in good agreement with the model predicted data. Under the condition of 10lx illumination, the SNR of typical objects can reach 27.02dB, which is much better than the requirement of 20dB for engineering application.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

Viral infections have long been the biggest threat to human survival, and from a medical perspective, the development of noninvasive high-throughput screening methods that target the incubation period to either treat diseases or limit viral spread would be strikingly effective. Using this technology to target viral incubation periods would also be inexpensive to perform. The current study proposes to transform pulse signals into a rapid diagnostic test using “coincidence analysis” in the hope of preventing or reducing the symptoms of viral infections. The heart plays a critical role in calculating and supplying the needs of all tissues of the body. Pulse waves are pressurized signals in response to heart’s calculations and include all phases of the cardiac cycle, which maintains life and provides energy needed to perform tasks. Any small movement gives a corresponding signal to pulse waves. The current study investigated conclusive data on self-limiting infections, such as common cold. We used pulse wave, coincidence analysis technology to capture signals from individuals with common cold during the incubation period and investigated if particular characteristic signals could be applied to influenza during the incubation period. Preliminary work demonstrated that pulse waves could generate signals using this technology that would be worthwhile for future research. A small amount of analytical data from common cold existed previously. The data structure is based on the idea that a single pulse wave at differing physiological conditions would have slight modifications that would be amplified and presented by various geometrical shapes after extensive data are accumulated. These geometric shapes can then be sliced vertically or horizontally to extract data during different illness stages. The significance of these findings are impressive; from a personal or a public hygiene perspective, this analytical technology provides many benefits, such as rapid and precise decision-making that can be directly visualized or can be analyzed using software programs. Also, this technology also uses futuristic wearable technology that brings practical problem solving to physiology.

The value of QuantiFERON in the diagnosis of tuberculosis and in the monitoring of the response to anti-tuberculosis treatment is unclear. The aims of this study were to evaluate the accuracy of the QuantiFERON-TB Gold In-Tube (QFT-GIT) test in the diagnosis of tuberculosis and in the monitoring of the response to anti-tuberculosis treatment in patients with active pulmonary tuberculosis (PTB). Between January 2013 and December 2015, 128 cases with active PTB and 128 controls with no mycobacterial infection, matched by age (within 3 years) and by the week that they visited Tainan Chest Hospital, were enrolled in the study. Serial testing by QFT-GIT at baseline and after 2 and 6 months of treatment was performed. At these time points, a comparison of the performance of QFT-GIT with that of sputum culture status among study subjects was conducted. Compared to baseline, 116 (87.2%) cases showed a decreased response, whereas 17 (12.8%) showed persistent or stronger interferon-gamma (IFN-γ) responses at 2 months. Their IFN-γ responses declined significantly from baseline to 2 months (median, 6.32 vs. 4.12; P < 0.005). The sensitivity values of the QFT-GIT test for the detection of pulmonary tuberculosis at cut-off points of 0.35 IU/ml, 0.20 IU/ml, and 0.10 IU/ml were 74.4%, 78.2%, and 80.5%, respectively. The specificity values at cut-off points of 0.35 IU/ml, 0.20 IU/ml, and 0.10 IU/ml were 66.2%, 63.9%, and 57.1%, respectively. Our results support the QFT-GIT assay as a potential tool for diagnosing tuberculosis and for monitoring the efficacy of anti-tuberculosis treatment.

Accurate diagnosis at an early stage of infection is essential for the successful management of any contagious disease. The COVID-19, caused by the SARS-CoV-2 virus is a pandemic that has affected 214 countries affecting more than 30.8 million people causing 0.957 million deaths as of third week of September, 2020. The primary diagnosis of the infection is done either by the molecular technique of RT-qPCR by detecting portions of the RNA of the viral genome or through immunodiagnostic tests by detecting the viral proteins or the antibodies produced by the host. As the demand for the test increased rapidly many naive manufacturers entered the market with novel kits and more and more laboratories also entered the diagnostic arena making the test result more error-prone. There are serious debates globally and regionally on the sensitivity and specificity of these tests and about the overall accuracy and reliability of the tests for decision making on control strategies. The significance of the test is also complexed by the presence of asymptomatic carriers, re-occurrence of infection in cured patients as well as by the varied incubation periods of the infection and shifting of the viral location in the host tissues. In this paper, we review the techniques available for SARS-CoV-2 diagnosis and probable factors that can reduce the sensitivity and specificity of the different test methods currently in vogue. We also provide a check-list of factors to be taken care to avoid fallacious practices to reduce false positive and false negative results by the clinical laboratories

Strata and surface movement induced by mining under open-pit final slope is a huge threat to mine safety. Physical model test is an important method to study mining-induced strata and surface movement laws. Because of rock joints predominantly control rock mass deformation and failure, thus physical model test leaving out of consideration of rock joints is difficult to reflect the influence of rock joints on rock mass deformation. Therefore, this paper presents a three-dimensional physical model test considering simplified dominant rock joints. This test process includes the design of testing equipment, the construction of physical model with dominant rock joint sets, conduction of mining and deformation monitoring. And mining under eastern final slope of Yanqianshan iron mine was selected as a case to study the behavior of mining-induced strata and surface movement.

Studies on the structure of economic systems are, most frequently, carried out by the methods of informational statistics. These methods, often accompanied by a wide range of indicators (Shannon entropy, Balassa coefficient, Herfindahl specialty index, Gini coefficient, Theil index etc.) around which a wide literature has been created over time, have a major disadvantage. Such weakness is related to the imposition of the system condition, therefore the need to know all the components of the system (as absolute values or as weights). This restriction is difficult to accomplish in some situations, and in others, this knowledge may be irrelevant, especially when there is an interest in structural changes only in some of the components of the economic system (either we refer to the typology of economic activities - NACE or of territorial units – NUTS). This article presents a procedure for characterizing the structure of a system and for comparing its evolution over time, in the case of incomplete information, thus eliminating the restriction existent in the classical methods. The proposed methodological alternative uses a parametric distribution, with subunit values for the variable. The application refers to Gross Domestic Product values for five of the 28 European Union countries, with annual values of over 1,000 billion Euros (Germany, Spain, France, Italy and United Kingdom) for the years 2003 and 2015. A form of the Wald sequential test is applied to measure changes in the structure of this group of countries, between the years compared. The results of this application validate the proposed method.

Shear connectors are used in steel beam–concrete slabs of composite frame and bridge structures to transfer shear force according to design loads. The existing Y-type perfobond rib shear connectors are designed for girder slabs of composite bridges. Therefore, the rib and transverse rebars of the conventional Y-type perfobond rib shear connectors are extremely large for the composite frames of building structures. We performed push-out tests of stubby Y-type perfobond rib shear connectors for composite frames. These shear connectors have relatively small ribs than conventional Y-type perfobond rib shear connectors. To confirm the shear resistance of these stubby shear connectors, we performed an experiment by using transverse rebars D13 and D16. The results indicate that these shear connectors have suitable shear strength and ductility for application in composite frame structures. The shear strengths obtained using D13 and D16 were not significantly different. However, the ductility of the shear connectors with D16 was 45.1% higher than that of the shear connectors with D13.

A cross-sectional study was carried out to determine the prevalence of subclinical mastitis (SCM) among medium to large scale household dairy farms in southwestern district, Jhenaidah, Bangladesh during July to December 2019. A total of 78 (n=100) lactating cows from household dairy farms (N=32) having three or more dairy cows were selected randomly as sampled populations. Milk samples were screened for SCM by using Surf Field Mastitis Test (SFMT). The prevalence of SCM varied among farm level [71.9% (95% CI: 53.3-86.3)], individual animal level [67.9% (95% CI: 56.4-86.3)] and quarter level [29.5% (95% CI: 24.5-34.9)]. Descriptive statistics represented the farmers and farm demography, characteristics of the sampled population, and overall management feature. Random Effect Logistic Regression identified, Body Condition Score (BCS) [OR=3.8 and 2.9, at cows level and quarter level respectively (BCS-2 vs. BCS-≥3)], and breed [OR=5.1 and 2.9, at cows level and quarter level respectively (HF× Sahiwal vs. HF × Local)] as potential risk factors. This study shows that SCM is highly prevalent in the study area, which is a major threat to the dairy industry's production performance. Regular screening by SFMT, proper hygiene, improve the management system, and farmer’s awareness is required to control the disease.

The antioxidant properties and polyphenol content of some selected aromatic plants grown in Greece were studied. Plants were refluxed with 60% methanol after acid hydrolysis. The phenolic substances were quantified by HPLC-DAD. The antioxidant capacity of the extracts was determined with the Rancimat test using sunflower oil as substrate. Free radical scavenging activity was measured using the stable free radical 1, 1-diphenyl-2-picrylhydrazyl (DPPH). Results were compared with standard BHT and ascorbic acid. Total phenol concentration of the extracts was estimated with Folin-Ciocalteu reagent using gallic acid as standard.

There is still a lack of a clinical test to reliably identify patients with Parkinson’s disease (PD) being at risk for aspiration. In this prospective, controlled, cross-sectional study we assessed if swallowing speed for water is a useful clinical test to predict aspiration proven by flexible endoscopic evaluation of swallowing (FEES). Due to this we measured the swallowing speed for 90 ml water in 115 consecutive and unselected PD outpatients of all clinical stages and 32 healthy controls. Average swallowing speed was lower in patients compared with controls (6.5 ± 3.9 ml/s vs. 8.5 ± 3.2 ml/s; p < 0.01). The disease-independent widely used threshold of < 10 ml/s showed insufficient sensitivity of 88% and specificity of 19% with unacceptable false-positive rates of 63% for patients and 69% for controls. Receiver operating characteristic (ROC) analysis was carried out to define a suitable cut-off value for detection of aspiration of water (area under the curve 0.72, p < 0.001) in PD patients. The optimized cut-off value was 5.5 ml/s with a sensitivity of 69% and a specificity of 64%. Overall, measuring swallowing speed is prone to methodological errors and not suitable as a screening instrument to predict aspiration in PD patients.

In this paper the development process of a deployable modular sandwich panelized system for rapid assembly building construction is presented, and its structural performance under some different action effects is investigated. This system, which includes an innovative sandwich panel and its integrated connections, can be used as structural walls and floors in quickly assembled post-disaster housing, as well as load bearing panels for pre-fabricated modular construction and semi-permanent buildings. Panels and connections are composed of a pneumatic fabric formwork, and two 3-D high-density polyethylene (HDPE) sheets as the skins, filled with high-density rigid Polyurethane (PU) foam as the core. HDPE sheets manufactured with a studded surface considerably enhance the stress distribution, buckling performance and delamination strength of the sandwich panel under various loading conditions. The load-carrying behaviour of the system in accordance with some ASTM standards is presented here. The results show the system satisfies the codes criteria regarding semi-permanent housing.

A face serum composed of a combination of biologically active compounds was evaluated for safety and efficacy in vitro, in a repeat insult patch test and in a human clinical efficacy trial. The serum inhibited tyrosinase activity modestly, decreased collagenase activity and exhibited notable free radical scavenging activity in vitro. It is gentle to the skin, as the serum did not irritate the skin or produce symptoms of allergic contact dermatitis in the 55 healthy adults that participated in the repeat insult patch test. In the efficacy trial, daily application of the face serum for 30 days significantly increased skin hydration, with all 35 volunteers experiencing improvement. Substantial improvements in skin elasticity, roughness (fine lines and wrinkles), and brightness also occurred during the trial. Dermatological examination also revealed a trend for reduced comedone count with use of the serum. Self-assessment responses revealed that all volunteers experienced improvements in multiple skin quality parameters and that participant perceptions are consistent with the results of the instrumental analyses. These findings indicated that the measured improvements in skin quality are not only statistically significant but are also clinically relevant as they were great enough for users of the face serum to feel and recognize.

2.25Cr-1Mo steel with high strength at high temperatures and good hydrogen resistance is widely used for power generation boiler material in high temperature and pressure use environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 285 and 21 ft-lb, which are drastically different values. The analysis of the fracture surface of the 21 ft-lb test specimen revealed MnS inclusions, and it was found that cracks initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 285 ft-lb impact specimen; however, the volume fraction of the inclusions was significantly less than that of the 21 ft-lb specimen. It was also found that the ferrite and carbide content of the 285 ft-lb specimen was less than 21 ft-lb specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation, such as MnS inclusions on ferrite and carbide, were compared and analyzed.

In only a few months after initial discovery in Wuhan, China, SARS-CoV-2 and the associated COVID-19 disease has become a global pandemic causing significant mortality and morbidity. In the absence of vaccines and effective therapeutics, reliable serological testing can be a key element of public health policy to control further spread of the disease and gradually ease quarantine measures. However, prior to launch of large-scale seroprevalence studies to assess herd immunity, it is critical to understand the limits and potential of current SARS-CoV-2 serological tests on the market. In this study, we provide an overview of serological testing and conduct a systematic review of independent evaluations of SARS-CoV-2 serological tests performance. Our findings show significant variability in the accuracy of marketed tests and highlight several lab-based and point-of-care rapid diagnostic tests with high performance level in detecting SRAS-CoV-2 specific antibodies. The findings of this review highlight the need for ongoing independent evaluations of commercialized COVID-19 diagnostic tests.

Natural calamities observation, study and simulation has always been a prime concern for disaster management agencies. Billions of dollars are spent annually to explore geo-seismic movements especially earthquakes but it has always been a unique accident. The real-time study of seismic waves, ground motions, and earthquakes always needed a programmable mechanical structure capable of physically producing the identical geo-seismic motions with seismology domain definitions. A programmable multi-parametric five degrees of freedom electromechanical seismic wave events simulation platform to study and experiment seismic waves and earthquakes realization in the form of geo-mechanic ground motions is exhibited in this work. The proposed platform was programmed and interfaced through an IoT cloud-based Web application. The geo-mechanics was tested in the range of i) frequencies of extreme seismic waves from 0.1Hz to 178Hz; ii) terrestrial inclinations from -10.000° to 10.000°; iii) velocities of 1km/s to 25km/s iv) variable arrival times 1us to 3000ms; v) magnitudes M1.0 to M10.0 earthquake; vi) epi-central and hypo-central distances of 290+ and 350+ kilometers. Wadati and triangulation methods have been used for entire platform dynamics design and implementation as one of key contributions in this work. This platform is as an enabler for a variety of applications such as training self-balancing and calibrating seismic-resistant designs and structures in addition to studying and testing seismic detection devices as well as motion detection sensors. Nevertheless, it serves as an adequate training colossus for machine learning algorithms and event management expert systems.

Organizational skills are a set of cognitive abilities responsible for goal-directed behaviors. While they are moderately studied in clinical settings, the assessment of organizational skills in the general population remains under-studied. This paper presents the new Durand Organizational Skills Questionnaire (DOSQ), which was developed to examine the factors associated with organizational abilities in the general population. Exploratory factor analysis, validated by a confirmatory factor analysis, suggests eight factors: Work Organization, Communication Clarity, Punctuality, Goal-Oriented Behavior, Assiduity, Workspace Organization, Strategies, and Attentiveness. Three studies using samples from the general population provided evidence for the reliability and validity of the DOSQ’s scores. Overall, the results suggest that the DOSQ offers a valid approach to measuring organizational skills in the general population.

The main objective of this paper is to find a close link between the adaptive level of significance, presented here, and the sample size. We, statisticians, know of the inconsistency, or paradox, in the current classical tests of significance that are based on p-value statistics that is compared to the canonical significance levels (10%, 5% and 1%): "Raise the sample to reject the null hypothesis" is the recommendation of some ill-advised scientists! This paper will show that it is possible to eliminate this problem of significance tests. The Bayesian Lindley's paradox – "increase the sample to accept the hypothesis" – also disappears. Obviously, we present here only the beginning of a possible prominent research. The intention is to extend its use to more complex applications such as survival analysis, reliability tests and other areas. The main tools used here are the Bayes Factor and the extended Neyman-Pearson Lemma.

Most diagnostic tests for tuberculosis (TB) rely on sputum samples, which are difficult to obtain and have low sensitivity in immunocompromised patients, patients with disseminated TB, and children, delaying treatment initiation. The World Health Organization (WHO) calls for the development of a rapid, biomarker-based, non-sputum test capable of detecting all forms of TB at the point-of-care to enable immediate treatment initiation. Lipoarabinomannan (LAM) is the only WHO-endorsed TB biomarker which can be detected in urine, an easily collected sample. This review discusses the characteristics of LAM as a biomarker, describes the performance of first-generation urine LAM tests and reasons for slow uptake, and presents considerations for developing the next-generation of more sensitive and impactful tests. Next-generation urine LAM tests have the potential to reach adult and pediatric patients regardless of HIV status or site of infection and facilitate global TB control. Implementation and scale-up of existing LAM tests and development of next-generation assays should be prioritized.

The study focused on two climatic variables i.e. precipitation and stream flow for analysing change in trend of rainfall for the River Ssezibwa Catchment area and stream flow of River Ssezibwa. This Catchment is found in the districts of Mukono and Buikwe in Uganda. In this area agriculture is majorly dependent on rainfall and irrigation on a small scale. However, rainfall occurrence has become unpredictable over the past few years as result of the changes in patterns of weather. This has caused severe effects on the agricultural cropping system as well as caused negative effects on the natural water resources. Stream flow data of 57 years (1960 – 2017) and rainfall data for 35 years (1982 – 2017) on a daily basis was analysed to find out the trend and detect change point. Trend analysis was done by using the non-parametric analysis while the change point detection was carried out by using the Pettit test (1979).Magnitude of trend for the time series data was carried out using Sen’s Slope estimator and Mann – Kendall test was done to determine the trend. Results from the statistical analysis highlighted that; for stream flow the trend was generally positive and change point detected to be in the year 2000 while for rainfall data analysis indicated that the trend was predominantly negative and change point was in the year 1998.

The lack of reliable rainfall projection records remains a major challenge to Uganda. In the advent of extreme wetness or drought events, reliable rainfall estimates for local planning and adaptation are essential. The present study used two main datasets to conduct a historical analysis from 1981 to 2019, coupled with future projections under representative concentration pathway (RCP 8.5) for the period 2020-2050. Historical analysis revealed bimodal annual rainfall pattern for March-May (MAM) and September-November (SON) gradients representing heavier to lighter rainfall events respectively over the study area. Investigation of recent trends in rainfall patterns revealed an upward trend from 2010 onwards in annual and seasonal rainfall. Moreover, results for future projections show wet conditions are projected to occur over the study area between the months of April/May and October. Contrarily, March is likely to experience a reduction in wet conditions. Mann-Kendall test employed to make future projections of rainfall depicted decreasing patterns during MAM season whilst increasing tendencies with strong shift was highlighted for SON season over the study region. Meanwhile, annual projections indicate huge variations with linear trends showing a marginal increase as compared to historical trends. Findings would serve as baseline print to propel further studies that could delve into impact analysis of drought extreme events which pose significant threats to the agricultural sector which is heavily reliant on rainfall.

Rainfall variability has resulted in extreme events like devastating floods and droughts which is the main cause of human vulnerability to precipitation in West Africa. Attempts have been made by previous studies to understand rainfall variability over Ghana but these have mostly focused on the major rainy season of April-July, leaving a gap in our understanding of the variability in the September-November season which is a very important aspect of the Ghanaian climate system. The current study seeks to close this knowledge gap by employing statistical tools to quantify variabilities in rainfall amounts, rain days, and extreme precipitation indices in the minor rainfall season over Ghana. We find extremely high variability in rainfall with a Coefficient of variation (CV) between 25.3% and 70.8%, and moderate to high variability in rain days (CV=14.0% - 48.8%). Rainfall amount was found to be higher over the middle sector (262.7 mm – 400.2 mm) but lowest over the east coast (125.2 mm – 181.8 mm). Analysis of the second rainfall season using the Mankandell Test presents a non-significant trend of rainfall amount and extreme indices (R10, R20, R99p, and R99p) for many places in southern Ghana. Rainfall Anomaly Indices show that the middle sector recorded above normal precipitation which is the opposite for areas in the transition zone. The result of this work provides a good understanding of rainfall in the minor rainfall season and may be used for planning purposes.

Climate change is a phenomenon that makes the climate system of a given region to be more unpredictable and increases the risk of water-related problems. GCMs under the new CMIP6 framework holds several climate models with many improvements as compared to past similar efforts. The improvements are mainly in the number of scenarios formulated, setup, parametrization, and resolution. In this study, 10 downscaled climate models from CMIP6 are evaluated by applying statistical and data mining tools and are ranked based on their capability to describe the historical observed series. The result of the analysis showed that the outputs of the MPI-ESM1-2-HR model have a good overall ranking among those 10 models. The output of this top-ranked model is used to understand future climate over UASB after properly bias-corrected using the QM method. Results of the bias correction step show that average annual precipitation has shown an increment of 6.5\% in the middle (SSP2-4.5) and 10.3\% in the worst (SSP5-8.5) case scenarios for the mid-century (2040 - 2069). Similarly, for the end of the century (2070 - 2099) an increment of 4.7\% and 17.5\% was predicted for the two scenarios respectively. Whereas average annual maximum temperature series showed an increment of 1.5 $\degree C$ for middle and 2.6 $\degree C$ for the worst case in the mid-century. At the same time, an increment of 2.2 $\degree C$ and 3.5 $\degree C$ were predicted for the end of the century similarly for those scenarios. Furthermore, it was predicted that the average annual minimum temperature series will have an increment of 2.6 $\degree C$ and 3.1 $\degree C$ for mid-century and 3.1 $\degree C$ and 4.7 $\degree C$ for the end century for the two scenarios respectively. An increase in precipitation with increased land degradation problems in the sub-basin increases the risk of flood events in the future.

The current coronavirus disease 2019 (COVID-19) pandemic is largely driven by community transmission, after 2019 novel Coronavirus (2019-nCoV or SARS-CoV-2) crosses the borders. To stop the spread, rapid testing is required at community clinics and hospitals. These rapid tests should be comparable with the standard PCR technology. Isothermal amplification technology provides an excellent alternative that is highly amenable to resource limited settings, where expertise and infrastructure to support PCR are not available. In this review, we provide a brief description of isothermal amplification technology, its potential and the gaps that need to be considered for SARS-CoV-2 detection. Among this emerging technology, loop mediated amplification (LAMP) and recombinase polymerase amplification (RPA) technologies have been identified as potential platforms that could be implemented at community level, without samples referral to a centralised laboratory and prolonged turn-around-time associated with the standard COVID-19 RT-PCR test. LAMP, for example, has recently been shown to be comparable with PCR and could be performed in less than 30 min by non-laboratory staff, without RNA extractions commonly associated with PCR. More so, it is cost effective and could easily be scaled up to resource limited settings. Diagnostics developers, scientific community and commercial companies could consider this alternative method to help stop the spread of COVID-19.

This paper presents results on tribological characteristics for polymer blends made of polybutylene terephthalate (PBT) and polytetrafluoroethylene (PTFE). This blend is relatively new in research as PBT has restricted processability because of its processing temperature near the degradation one. Tests were done block-on-ring tribotester, in dry regime, the variables being the PTFE concentration (0%, 5%, 10% and 15%wt) and the sliding regime parameters (load: 1 N, 2.5 N and 5 N, the sliding speed: 0.25 m/s, 0.5 m/s and 0.75 m/s, and the sliding distance: 2500 m, 5000 m and 7500 m). Results are encouraging as PBT as neat polymer has very good tribological characteristics in terms of friction coefficient and wear rate. SEM investigation reveals a quite uniform dispersion of PTFE drops in the PBT matrix.

The excitation of the visual system increases with increasing retinal illumination. At the same time, the sensitivity of the system decreases (light adaptation). Higher excitation automatically results in a lower sensitivity. This study investigates whether this parallelism between the excitation and the sensitivity also applies in the dynamic case, that is, during the transition to a higher excitation level after an increase in the retinal illuminance. For this purpose, the courses of the subjective and the electroretinographic threshold during the transitional phase after a step of the adaptation illumination was determined by means of a special light-stimulation apparatus. As a measure of the course of the excitation during this time, the response ERG on the adaptation step was recorded with a special amplifier. The threshold curve always has an overswing, which shows subjectively very strong differences. It can be concluded that the glare caused by a sudden increase in illuminance is subjectively very different. The comparison between the response ERG on the adaptation step and the course of the electroretinographic increment threshold during this time shows a broad agreement between the two courses. It can thus be assumed that the sensitivity of the visual system follows the course of the excitation also in the dynamic case. In addition, the investigation shows that the glare experienced after a step in the illuminance clearly shows great subjective differences.

Land Surface Temperature (LST) is a basic parameter in energy exchange between the land and atmosphere and is frequently used in many sciences such as climatology, hydrology, agriculture, ecology, etc. LST time series data have usually deficient, missing and unacceptable data caused by the presence of clouds in images, presence of dust in atmosphere and sensor failure. In this study, Singular Spectrum Analysis (SSA) algorithm was used to resolve the problem of missing and outlier data caused by cloud cover. The region studied in the present research included an image frame of MODIS with horizontal number 22 and vertical number 05 (h22v05). This image involved a large part of Iran and Turkmenistan and Caspian Sea. In this study, MODIS LST sensor (MOD11A1) was used during 2015 with 1×1 Km spatial resolution and day/night LST data (daily temporal resolution). The results of the data quality showed that cloud cover caused 36.37% of missing data in the studied time series with 730 day/night LST images. Further, the results of SSA algorithm in reconstruction of LST images indicated the Root Mean Square Error (RMSE) of 2.95 K between the original and reconstructed data in LST time series in the study region. In general, the findings showed that SSA algorithm using spatio-temporal interpolation in LST time series can be effectively used to resolve the problem of missing data caused by cloud cover.

This study investigated whether biogas reactor performance, including microbial community development, in response to a change in substrate composition is influenced by initial inoculum source. Test reactors were first started with two different inocula and operated with the same grass-manure mixture for more than 120 days. These reactors initially showed great differences depending on inoculum source, but eventually showed similar performance and overall microbial community structure. At the start of the present experiment, the substrate was complemented with milled feed wheat, added all at once or divided into two portions. The starting hypothesis was that process performance depends on initial inoculum source and microbial diversity, and thus that reactor performance is influenced by the feeding regime. In response to the substrate change, all reactors showed increases and decreases in volumetric and specific methane production, respectively. However, specific methane yield and development of the microbial community showed differences related to initial inoculum source, confirming the hypothesis. The different feeding strategies had however only minor effects on process performance and overall community structure, but still induced differences in the cellulose-degrading community and in cellulose degradation.

In this work, a hybrid component Fault Detection and Diagnosis (FDD) approach for industrial sensor systems is established and analyzed, to provide a hybrid schema that combines the advantages and eliminates the drawbacks of both model-based and data-driven methods of diagnosis. Moreover, it shines the light on a new utilization of Random Forest (RF) together with model-based diagnosis, beyond its ordinary data-driven application. RF is trained and hyperparameter tuned using three-fold cross validation over a random grid of parameters using random search, to finally generate diagnostic graphs as the dynamic, data-driven part of this system. This is followed by translating those graphs into model-based rules in the form of if-else statements, SQL queries or semantic queries such as SPARQL, in order to feed the dynamic rules into a structured model essential for further diagnosis. The RF hyperparameters are consistently updated online using the newly generated sensor data to maintain the dynamicity and accuracy of the generated graphs and rules thereafter. The architecture of the proposed method is demonstrated in a comprehensive manner, and the dynamic rules extraction phase is applied using a case study on condition monitoring of a hydraulic test rig using time-series multivariate sensor readings.

The main purpose of this paper is to present a system to detect extrusion failures in Fused Deposition Modelling (FDM) 3D printers by sensing that the filament is moving forward properly. After several years using these kind of machines, authors detected that there is not any system to detect the main problem in FDM machines. Authors thought in different sensors and used the Weighted Objectives Method, one of the most common evaluation methods, for comparing design concepts based on an overall value per design concept. Taking into account the obtained scores of each specification, the best choice for this work is the optical encoder. Once the sensor is chosen, it is necessary to design de part where it will be installed without interfering with the normal function of the machine. To do it, photogrammetry scanning methodology was employed. The developed device perfectly detects the advance of the filament without affecting the normal operation of the machine. Also, it is achieved the primary objective of the system, avoiding loss of material, energy and mechanical wear, keeping the premise of making a low-cost product that does not significantly increase the cost of the machine. This development has made it possible to use the printer with remains coil filament, which were not spent because they were not sufficient to complete an impression and also printing models in two colours with only one extruder.

In the context of the COVID-19 Pandemic, the use of surgical masks has become the new normal. The use of these devices in exercise and medical situations has been advocated with the purpose of reducing contagions, but some concerns exist regarding its safety. We performed maximal treadmill stress tests in 12 healthy young subjects, with and without surgical mask use, and measured exercise capacity, oxygen saturation (rest, peak exercise and post-exercise) and electrocardiographic changes. Exercise capacity and Oxygen saturation levels decreased in peak exercise vs rest in a statistically significant manner when mask was used. ECG changes, although not significant, were present in 3 subjects when mask was used and disappeared when the test was made unmasked. We conclude that masked exercise has the potential to cause decreased exercise load and oxygen saturation and potentially cause diagnostic errors in medical exams.

The role of vitamin D in the prevention and treatment of non-skeletal health issues has received significant media and research attention in recent years. Costs associated with clinical management of low vitamin D (LVD) have increased exponentially. However, no clear evidence supports vitamin D screening to improve health outcomes. Authoritative bodies and professional societies recommend against population-wide vitamin D screening in community-dwelling adults who are asymptomatic or at low risk of LVD. In order to assess patterns of physician management of LVD in this conflicting environment, we conducted a scoping review of three electronic databases and gray literature. Thirty-eight records met inclusion criteria and were summarized in an evidence table. Results from seven countries showed a consistent increase in vitamin D lab tests and related costs. Many vitamin D testing patterns reflected screening rather than targeted testing for individuals at high risk of vitamin D deficiency or insufficiency. Interventions aimed at managing inappropriate clinical practices related to LVD were effective in the short term. Variability and controversy were pervasive in many aspects of vitamin D management, shining light on physician practices in the face of uncertainty. Future research is needed is needed to inform better clinical guidelines and to assess implementation practices that encourage evidence-based management of LVD in adult populations.

In this paper a robust version of the Wald test statistic for composite likelihood is considered by using the composite minimum density power divergence estimator instead of the composite maximum likelihood estimator. This new family of test statistics will be called Wald-type test statistics. The problem of testing a simple and a composite null hypothesis is considered and the robustness is studied on the basis of a simulation study. Previously, the composite minimum density power divergence estimator is introduced and its asymptotic properties are studied.

This paper introduces an approach that chooses the fault detection by calculating probabilities using probability mass function (pmf) and cumulative distribution function (CDF). This work used a method for multiple stuck-at faults by producing a new test pattern in combinational circuits. We assumed that existence of all multiple faults is only because of one single component that is faulty. A complete test set can be created by all possible single stuck-at faults in a combinational circuit using some combination of gates. The test set generation fault detection method is applied on two different 3-bit input variable and 4-bit input variable circuits. The probability of error occurrence is calculated at both 3-bit and 4-bit input variable circuits. The resulting feature is used to obtain maximum error occurrence probability to detect faults by the logic used that the complexity of the circuit is inversely proportional to the fault occurrence probability. Then again, undetectability is directly proportional to the complexity of the circuit. Therefore, finest feasible circuit should have large input variable components with less complexity to reduce the fault occurrence probability.

Alumina dispersion-strengthened copper, Glidcop, is used widely in high-heat-load ultra-high-vacuum components for synchrotron light sources (absorbers), accelerator components (beam intercepting devices) and in nuclear power plants. Glidcop has similar thermal and electrical properties to OFE (oxygen free electrical) copper, but has superior mechanical properties, thus making it a feasible structural material; its yield and ultimate strength are equivalent to those of mild-carbon steel. The purpose of this work has been to develop a brazing technique to join Glidcop to Mo, using a commercial Cu-based alloy. The effects of the excessive diffusion of the braze along the grain boundaries on the interfacial chemistry and joint microstructure, as well as on the mechanical performance of the brazed joints, has been investigated. In order to prevent the diffusion of the braze into the Glidcop alloy, a copper barrier layer has been deposited on Glidcop by means of RF-sputtering.

The assessment of positive emotional states in animals has been advanced considerably through the use of judgement bias testing. JBT methods have now been reported in a range of species. Generally, these tests show good validity as ascertained through use of corroborating methods of affective state determination. However, published reports of judgement bias task findings can be counter-intuitive and show high inter-individual variability. It is proposed that these outcomes may arise as a result of inherent inter- and intra-individual differences as a result of biology. This review discusses the potential impact of sex and reproductive cycles, social status, genetics, early life experience and personality on judgement bias test outcomes. We also discuss some aspects of test design that may interact with these factors to further confound test interpretation. There is some evidence that a range of biological factors affect judgement bias test outcomes, but in many cases this evidence is limited and needs further characterisation to reproduce the findings and confirm directions of effect. It is our proposition that researchers should consider dedicated study on these factors and their impact on judgement biasing. This is needed to confirm effect and investigate mechanisms. Alternately, consideration and reporting of these factors in JBT studies through incorporation in statistical analyses will provide much needed additional data on their impact. These actions will enhance the validity and practical applicability of the JBT for welfare assessment.

Constructed rapid infiltration system (CRI) is a new type of sewage biofilm treatment technology, but due to its anaerobic zone lacks of the carbon sources and the condition for nitrate retention, its nitrogen removal perfomance is very poor; However, shortcut nitrification-denitrification process presents distinctive advantages, as it saves oxygen, requires less organic matter and needs less time for denitrification compared to conventional nitrogen removal method. Thus, if the shortcut nitrification-denitrification process could be applied to CRI system properly, the simpler, more economic and efficient nitrogen removal method will be obtained. But, as its reaction process shows that the first and the most important step of achieving shortcut nitrification-denitrification is to achieve shortcut nitrification. Thus, in this study, we explored the feasibility to achieve shortcut nitrification, which produces nitrite as the dominant nitrogen species in effluent, by addition of potassium chlorate (KClO₃) to the influent. In an experimental CRI model system, the effects on nitrogen removal, nitrate inhibition and nitrite accumulation were studied, and the advantages of achieving shortcut nitrification-denitrification were also analysed. The results showed that shortcut nitrification was successfully achieved and maintained in a CRI system by adding 5 mM KClO₃ to the influent at a constant pH of 8.4. Under these conditions nitrite accumulation rate was increased, while a lower concentration of 3 mM KClO₃ had no obvious effect. The addition of 5 mM KClO₃ in influent presumably allowed sufficient activity of ammonia-oxidizing bacteria (AOB) but inhibited nitrite-oxidizing bacteria (NOB) strongly enough to result in a maximum nitrite accumulation rate of up to over 80%. As a result, nitrite became the dominant nitrogen product in the effluent. Moreover, if the shortcut denitrification will be achieved in the subsequent research, it could save 60.27 mg carbon source (CH₃OH) consumption when treatment of per liter sewage in CRI system compared with full denitrification process.

This study aims to improve the shaft with hexagon joints to be a type not requiring welding or bolts in the static load test . In order to evaluate the bearing capacity of helical piles, two sites were selected to conduct pile installation for the field test and the pile load test. For the pile load test, the static pile load test and the dynamic pile load test were carried out, and torque was measured during pile installation for the field test to compare and analyze expected bearing capacity and thus assess the feasibility of the method for estimating the bearing capacity. The field pile load test revealed the bearing capacity of the gravity grout pile was the same or greater than 600kN in the static pile load test in accordance with AC 358 Code. The non-grout pile showed the bearing capacity the same or smaller than 600kN, suggesting gravity grouting is required. Moreover, the field pile load test was used to establish the bearing capacity equation considering the torque in pile installation, and a small number of samples were used to establish the equation which can be used as a basic data.

The development of hybrid rockets offers excellent opportunities for the practical education of students at universities due to a high safety and a relatively low complexity of the rocket propulsion system. During the German educational program STERN, students of the Technische Universität Braunschweig obtain the possibility to design and launch a sounding rocket with a hybrid engine. The design of engine HYDRA 4X is presented and results of first engine tests are discussed. Results for measured regression rates are compared to results from literature. Furthermore, the impact of the lightweight casing material CFRP on the hybrid engine mass and flight apogee altitude is examined for rockets with different total impulse classes (10 to 50 kNs). It is shown that the benefit of a lightweight casing material on engine mass decreases with an increasing total impulse. However, a higher gain on apogee altitude, especially for bigger rockets with a comparable high total impulse is shown.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

An analysis of the performance of Automatic Dependent Surveillance-Broadcast (ADS-B) data received from the Grand Forks, North Dakota International Airport was carried out in this study. The purpose was to understand the vulnerabilities of Universal Access Transceiver (UAT) ADS-B system and recognize the effects on present and future Air Traffic Control (ATC) operation. The Federal Aviation Administration (FAA) mandated all the General Aviation aircraft to be equipped with ADS-B. The aircraft flying within United States and below the transition altitude (18,000 feet) are more likely to install an UAT ADS-B. At present unmanned aircraft systems (UAS) and autonomous air traffic control (ATC) towers are being integrated into the aviation industry and UAT ADS-B is a basic sensor for both class 1 and class 2 Detect and Avoid (DAA) systems. As a fundamental component of future surveillance system, the anomalies and vulnerabilities of ADS-B system need to be identified to enable a fully utilized airspace with enhanced situational awareness. The data received was archived in GDL-90 format, which was parsed into readable data. The anomaly detection of ADS-B messages was based on the FAA ADS-B performance assessment report. The data investigation revealed ADS-B message suffered from different anomalies including drop out; missing payload; data jump; low confident data and altitude discrepancy. Among those studied, the most severe was drop out and 32.49% of messages suffered from this anomaly. Dropout is an incident where ADS-B failed to update within a specified rate. Considering the potential danger being imposed, an in-depth analysis was carried out to characterize message dropout. Three flight parameters were selected to investigate their effect on drop out. Statistical analysis was carried out and Friedman Statistical Test identified that altitude affected drop out more than any other flight parameters.

Oriented strand board (OSB) panels are widely marketed for several applications, from building to packaging. The manufacturing of poplar OSB started recently in Northern Italy representing a relevant innovation in the sector since this product is usually made of coniferous wood. The thermal treatment is widely used for reducing the hygroscopicity of wood-based products, nonetheless it influences the mechanical behavior and degrades the main components of wood, which can affect their finishing. Therefore, it is important to know the properties of the treated surfaces. To this purpose, in this study a lot of OSB panels, made of poplar wood, 15 mm thick and with a density of 590 kg/m³, were thermally treated under vacuum conditions at 190 °C for 2 h and then subjected to accelerated weathering. The changes in color and in wettability due to treatment and accelerated weathering were studied. The thermal treatment determined a significant darkening of the color; the accelerated weathering darkened the untreated surfaces and, on the opposite, lightened the thermo-treated surfaces. The wettability decreased after thermal treatment and increased after weathering, more evidently in treated panels. Overall, this study improves the knowledge about the behavior of the surface of thermo-treated poplar OSB, which is relevant for the industrial coating of this product.

Identifying anti-spike antibodies that exhibit strong neutralizing activity against current dominant circulating variants and antibodies that are escaped by these variants have important implications in the development of therapeutic and diagnostic solutions as well as in improving understanding of the humoral response to SARS-CoV-2 infection. We characterized seven anti-RBD monoclonal antibodies for their binding activity, pairing capability and neutralization activity to SARS-CoV-2 and three variant RBDs (UK, SA and BR P.1) via lateral flow immunoassays. The results allowed us to group these antibodies into three distinct epitope bins. Our studies showed that two antibodies had broadly potent neutralizing activity against SARS-CoV-2 and these variant RBDs and that one antibody did not neutralize the SA and BR P.1 RBDs. The antibody escaped by the SA and BR P.1 RBDs retained binding activity to SA and BR P.1 RBDs but was unable to induce neutralization. Further, we demonstrated that the lateral flow immunoassay can be a rapid and effective tool for antibody characterization, including epitope classification and antibody neutralization kinetics. From these studies, the potential contributions of the mutations (N501Y, E484K and K417N/T) contained in these variants’ RBDs on antibody pairing capability, neutralization activity and therapeutic antibody targeting strategy are discussed.

The calculation of the release of liquid hazardous chemicals storage tanks is an important part of the quantitative risk assessment of accidents. This paper mainly establishes a continuous real–time release model based on the instantaneous mass flow Q_m model. Meanwhile, the software function module was analyzed, and programming software was developed using C# language for model solving. A series of experiments for repeated leakage tests was designed and the discharges through three small holes with different heights for 200 s were observed. The results show that the continuous real–time leakage model is effective, and the deviation between theoretical and experimental release amounts are within a reasonable range. The higher the liquid level above the leak hole is, and the smaller the height of the leak hole from the ground is, the greater the flow rate at the leak orifice is and the smaller discharge rate change is. Therefore, the deviation between the theoretical release amount M_t and the experimental average release amount Ma is greater while the height of the leak hole from the ground is smaller, which indicates that the smaller the distance from the leak orifice to the ground, the greater the influence of the empirical discharge coefficient C₀ on the release amount M.

The COVID-19 pandemic has created huge damage to society and brought panics around the world. Such panics can be ascribed to the seemingly deceptive features of the COVID-19: compared to other deadly viral outspreads, it has medium transmission and mortality rates. As a result, the severity of the causative coronavirus, SARS-CoV-2, was deeply underestimated by the society at the beginning of the COVID-19 outbreak. Based on this, in this review, we define the viruses with features similar to those of SARS-CoV-2 as the Panic Zone viruses. To contain those viruses, accurate and fast diagnosis followed by effective isolation and treatment of patients are pivotal at the early stage of virus breakouts. This is especially true when there is no cure or vaccine available for a transmissible disease, which is the case for current COVID-19 pandemic. As of January 2021, more than two hundred kits for the COVID-19 diagnosis on the market are surveyed in this review, while emerging sensing techniques for SARS-CoV-2 are also discussed. It is of critical importance to rationally use these kits for the efficient management and control of the Panic Zone viruses. Therefore, we discuss guidelines to select diagnostic kits at different outbreak stages of the Panic Zone viruses, SARS-CoV-2 in particular. While it is of utmost importance to use nucleic acid-based detection kits with low false negativity (high sensitivity) at the early stage of an outbreak, the low false positivity (high specificity) gains its importance at later stages of the outbreak. When a society is set to reopen from the lock-down stage of the COVID-19 pandemic, it becomes critical to have antibody based immunoassay kits with high specificity to identify people who can safely return to the society after their recovery of SARS-CoV-2 infections. Given that the emergence of mutant viruses at the beginning of 2021 has complicated current battle against the COVID-19, we also discussed approaches and guidelines to detect viral mutants in the middle of the second wave of the pandemic that started at the end of 2020. Finally, since a massive attack from a viral pandemic requires a massive defense from the whole society, we urge both government and private sectors to research and develop more affordable and reliable point-of-care testing (POCT) kits, which can be used massively by the general public (and therefore called as massive POCT) to contain Panic Zone viruses in future.

The epidemiological situation generated by COVID-19 has highlighted the importance of applying non-pharmacological measures. Among these, mass screening of the asymptomatic general population has been established as a priority strategy by carrying out diagnostic tests to limit the spread of the virus. In this article, we aim to evaluate the economic impact of mass COVID-19 screenings of an asymptomatic population through a Cost-Benefit Analysis based on the estimated total costs of mass screening versus health gains and associated health costs avoided. Excluding the value of monetized health, the Benefit-Cost ratio was estimated at approximately 0.45. However, if monetized health is included in the calculation, the ratio is close to 1.20. The monetization of health is the critical element that tips the scales in favour of the desirability of screening. Screenings with the highest return are those that maximize the percentage of positives detected.

Sedation is a ubiquitous practice in ICUs and NCCUs. It has the benefit of reducing cerebral energy demands, but also precludes an accurate neurologic assessment. Because of this, sedation is intermittently stopped for the purposes of a neurologic assessment, which is termed a neurologic wake-up test (NWT). NWTs are considered to be the gold-standard in continued assessment of brain-injured patients under sedation. NWTs also produce an acute stress response that is accompanied by elevations in blood pressure, respiratory rate, heart rate, and ICP. Utilization of cerebral microdialysis and brain tissue oxygen monitoring indicates that this is not mirrored by alterations in overall cerebral metabolism, and seldom affects oxygenation. The hard contraindications for the NWT are preexisting intracranial hypertension, barbiturate treatment, status epilepticus, and hyperthermia. However, hemodynamic instability, sedative use for primary ICP control, and sedative use for severe agitation or respiratory distress are considered significant safety concerns. Despite ubiquitous recommendation, it is not clear if additional clinically relevant information is gleaned through its use, especially with the contemporaneous utilization of multimodality monitoring. Various monitoring modalities provide unique and pertinent information about neurologic function, however, their role in improving patient outcomes and guiding treatment plans has not been fully elucidated. There is a paucity of information pertaining to the optimal frequency of NWTs, and if it differs based on type of injury. Only one concrete recommendation was found in the literature, exemplifying the uncertainty surrounding its utility. The most common sedative used and recommended is propofol because of its rapid onset, short duration, and reduction of cerebral energy requirements. Dexmedetomidine may be employed to facilitate serial NWTs, and should always be used in the non-intubated patient or if propofol infusion syndrome (PRIS) develops. Midazolam is not recommended due to tissue accumulation and residual sedation confounding a reliable NWT. Thus, NWTs are well tolerated in most patients and remain recommended as the gold-standard for continued neuromonitoring. Predicated upon one expert panel, they should be performed at least one time per day. Propofol or dexmedetomidine are the main sedative choices, both enabling a rapid awakening and consistent NWT.

Anomaly occurrences in hydraulic machinery may lead to massive systems shut down, jeopardizing the safety of the machinery and its surrounding human operator(s) and environment, and the severe economic implications succeeding the faults and their associated damage. Hydraulics are mostly placed in ruthless environments, where they are consistently vulnerable to many faults. Hence, not only the machines and their components are prone to anomalies, but also the sensors attached to them, which monitor and report their health and behavioral changes. In this work, a comprehensive applicational analysis of anomalies in hydraulic systems extracted from a hydraulic test rig is thoroughly achieved. Firstly, we provided a combination of a new architecture of LSTM autoencoders and supervised machine and deep learning methodologies to perform two separate stages of fault detection and diagnosis. The two phases are condensed by: the detection phase using the LSTM autoencoder. Followed by the fault diagnosis phase represented by the classification schema. The previously mentioned framework is applied to both component and sensor faults in hydraulic systems, deployed in the form of two in-depth applicational experiments. Moreover, a thorough literature review of the past decade related work for the two stages separately is successfully conducted in this paper.

Background: The maximal one-repetition test (1-RM) is widely used in scientific research; however, there are conflict results regarding its reproducibility in elderly population. The present study aimed to analyze the reproducibility the test both before and after a 12 week training period by using the bench press and leg press 45° 1-RM tests in the elderly taking into consideration the training experience and strength level of the women. Methods: Elderly women (n = 376; age, 68.5 ± 14.1 years; height, 162.7 ± 5.5 cm; body mass, 71.2 ± 16.0 kg) who underwent ≥3 months of resistance training performed an initial week of familiarization and a second week of testing and retest, with a 48–72 hour interval. Results: The results showed maximal and relative load strength of 39.3 kg and 0.59 kg/body mass for lower limbs and 20.9 kg and 0.31 kg/body mass for upper limbs. The Kappa indices were 0.93 and 0.95, and the intraclass correlation coefficients were 0.99 and 0.99 for the lower and upper limbs, respectively. Conclusion: Therefore, the present study confirms that the 1-RM test has high reliability and reproducibility in the elderly, for both upper and lower limbs.

In the last decade, the tremendous improvement in the sensitivity and also affordability of Liquid Chromatography-tandem Mass Spectrometry (LC-MS/MS) have revolutionized its application in pharmaceutical analysis, resulting in wide-spread of employing LC-MS/MS for determining pharmaceutical compounds including anticancer drugs in pharmaceutical research and also industries. Currently, LC-MS/MS has been widely used to quantify small molecule oncology drugs in various biological matrices to support preclinical and clinical Pharmacokinetic studies in R & D of oncology drugs. This mini-review article will describe the state-of-the art LC-MS/MS and its application in rapid quantification of small molecule anticancer drugs. In addition, efforts have also been made in this review to address several key aspects in the development of rapid LC-MS/MS methods, including sample preparation, chromatographic separation and matrix effect evaluation.

Sentinel-1A/B radar remote sensing data were applied for the first time to determine the sixth nuclear test, its underground explosion h-bomb location and affected zone in North Korea, on September 3, 2017. Location of epicenters nuclear test were found according to line-of-sight displacement images via its maximum value. Line-of-sight displacement images were obtained by processing in the GMTSAR package in the VirtualBox virtual machine of the Linux Ubuntu 16.04 operation system. In this research, three scenes Sentinel-B data with descending orbits were considered, one after and two before the event (the nuclear test date) scene were used.

In recent years, cemented tailings/paste backfill (CPB) become more and more important to maintain mine structure and keep mining stope to be stable in deep underground mining. Deep mining process often accompanied by blasting, rock burst and other high-speed dynamic loading. So it’s important to make research on dynamic behavior and characteristics of CPB. In this paper, a series of dynamic loading tests on CPB specimens by SHPB were taken to study the characteristic of stress-strain, dynamic strength, deformation and failure of CPB. The experimental results revealed that some CPB specimens have 1~2 lower stress peaks after reaching the peak stress before getting completely failed. The greater the cement-sand ratio was, the more obvious of strain reaction was. This property mainly showed like follows. The greater the cement-sand ratio was, the greater the dynamic compressive strength was under similar velocity impact; the dynamic compressive strength and the average strain rate were quadratic equation relationship, and the greater the cement-sand ratio was, the higher increase rate of dynamic compressive strength caused by strain rate. The dynamic compressive strength enhancement factor increased with the increase of the strain rate, and is larger than that of rock samples. The failure forms of CPB specimens under low-speed impact were almost the same as them under static uniaxial and triaxle compression. The CPB specimens were crushed broken under the critical strain rate, similar to the failure mode of low strength concrete. The experimental research results will improve our understanding the dynamic mechanical property of CPB and help to guide the strength design of deep mining backfill.

Owing to fascinating applications of ZnO in modern devices, it is interesting to explore its more features for future devices. Hence, herein, we have synthesized the high quality ZnO spherical nanoparticles (SNPs) through a facile green synthesis route and robust structural and biomedical studies are carried out. Hexagonal phase with 93.2% crystallinity was confirmed through XRD analysis. ZnO nanoparticles were tested for their bioactivities both in vivo (acute cytotoxicity test) and in vitro (Anti-cancer activities on liver (HepG2) and cervical (Hela) cancer cell lines, stimulatory/inhibitory effects on normal rat splenic cells and hemolytic effects on red blood cells). Results showed that ZnO SNPs has no cytotoxic effects on vital organ like liver and has no hemolytic action on red blood cells. ZnO SNPs showed inhibitory consequence on normal rat splenic cells growth at all tested concentrations. ZnO nanoparticles showed an inhibitory effect on HepG2 cell line. While showed stimulatory effect on Hela cell line. Current study presents the synthesized ZnO SNPs as highly applicable in bio-optoelectronics.

Earthquake is among the most devastating natural disasters causing severe economic, environmental, and social destruction. Earthquake safety assessment and building hazard monitoring can highly contribute to urban sustainable development through identification and insight into optimum materials and structures. While the vulnerability of structures mainly depends on the structural resistance, the safety assessment of buildings can be highly challenging. In this paper, we consider Rapid Visual Screening (RVS) method which is a qualitative procedure for estimating structural scores for buildings suitable for medium- to high-seismic cases. This paper presents an overview of the common RVS methods, i.e., FEMA P-154, IITK-GGSDMA, and EMPI. To examine the accuracy and validation, a practical comparison is performed between their assessment and observed damage of reinforced concrete buildings from a street survey in the Bingöl region, Turkey, after the 11 May 2003 earthquake. The results demonstrate that the application of RVS methods for preliminary damage estimation is a vital tool. Furthermore, the comparative analysis showed that FEMA P-154 creates an assessment that overestimates damage states and is not economically viable while EMPI and IITK-GGSDMA provide for more accurate and practical estimation, respectively.

Managing blood cholesterol levels is important for the treatment and prevention of diabetes, cardiovascular disease, and obesity. An easy-to-use, portable cholesterol blood test will accelerate more frequent testing by patients and at-risk populations. We aim to evaluate the performance of smartphone-based point-of-care cholesterol blood tests as compared to that of hospital-grade laboratory tests. We used smartphone systems that are already familiar to many people. Because smartphone systems can be carried around everywhere, blood can be measured easily and frequently. We compared the results of cholesterol tests with those of existing clinical diagnostic laboratory methods. We found that smartphone-based point-of-care lipid blood tests are as accurate as hospital-grade laboratory tests (N=116, R>0.97, P<0.001 for all 3 cholesterol blood tests: total cholesterol, high density lipoprotein, and triglyceride). Our system will be useful for those who need to manage blood cholesterol levels to motivate them to track and control their behavior.

Introduction: The SARS-CoV2 pandemic has led to an worldwide shortage of Personal Protection Devices (PPD) for medical and paramedical personnel. Adaptation of commercially available snorkel masks to serve as full face masks has been proposed. Even not formally approved as PPD, they are publicized on social media as suitable for this use. Concerns about actual protection levels and risk of carbon dioxide (CO₂) accumulation while wearing them for extended periods made us perform a systematic testing of various brands, in order to verify whether they are as safe and effective as claimed. Methods: A ‘fit’ test was performed, analogous to gas mask testing. Respiratory safety was evaluated by measuring end-tidal CO₂ and oxygen saturation while wearing the masks in rest and during physical exercise. Masks were tested with 3D adaptors to mount regular bacterial-viral ventilator filters when available, or with snorkel openings covered with N95/FFP2 cloth. Results: Modified masks performed reasonably well on the fit test, comparable to regular N95/FFP2 masks. Not all ventilator filters are equally protective. For all masks, a small initial increase in end-tidal CO₂ was noted, remaining within physiological limits. Masks with specific adaptors (3D printed or provided by the manufacturer) are safer, have more flexibility and reliability than makeshift adaptations. Conclusions: These masks can offer benefit as a substitute for complete protective gear as they are easier to don and remove and offer full-face protection. They may be more comfortable to wear for extended periods. Proper selection of mask size, fit testing, quality of 3D printed parts and choice of filter are important.

Nowadays, according to spectacular improvement in health care and biomedical level, a tremendous amount of data is recorded by hospitals. In addition, the most effective approach to reduce disease mortality is to diagnose it as soon as possible. As a result, data mining by applying machine learning in the field of diseases provides good opportunities to examine the hidden patterns of this collection. An exact forecast of the mortality after heart surgery will cause Successful medical treatment and fewer costs. This research wants to recommend a new stacking predictive model after utilizing the random forest feature importance method to foresee the mortality after heart surgery on a highly unbalanced dataset by using the most practical features. To solve the unbalanced data problem, a combination of the SVM-SMOTE over-sampling algorithm and the Edited-Nearest-Neighbor under-sampling algorithm is used. This research compares the introduced model with some other machine learning classifiers to ensure efficiency through shuffle hold-out and 10-fold cross-validation strategies. In order to validate the performance of the implemented machine learning methods in this research, both shuffle hold-out, and 10-fold cross-validation results indicated that our model had the highest efficiency compared to the other models. Furthermore, the Friedman statistical test is applied to survey the differences between models. The result demonstrates that the introduced stacking model reached the most accurate predicting performance after Logistic Regression.

There are some limitations in the null test measurement in the stitching interferometry. In order to meet the null test conditions, the moving distance between the sub-apertures often deviates from the theoretical preset distance, which leads to a position deviation of sub-apertures under measurements. To overcome this problem, an algorithm for data processing is proposed. We used iterative calculation of the deviations between the sub-apertures to adjust their positions, to ensure the local validity of the linear approximation algorithm and realize the exact stitching. A cylindrical lens as an object for experimental examination of the proposed method was taken. The obtained results demonstrate the validity, reliability and feasibility of our iterative stitching algorithm.

Background: Flow-through dot-blot assay (FT-DBA) for SARS-CoV-2 specific IgG detection will provide a reliable and affordable immunoassay for the rapid serosurveillance against COVID-19. Method: SARS-CoV-2 antigens were immobilized on nitrocellulose membrane to capture IgG immunoglobulins, which were then detected with AuNP anti-human IgG. A total of 181 samples were characterized with in-house and commercial immunoassay. The positive panel consisted of RT-PCR positive samples from patients with both <14 days and >14 days from the onset of symptoms, while the negative panel contained samples collected either from the pre-pandemic era dengue patients from healthy donors during the pandemic period. Results: In-house ELISA selected a total of 79 true seropositive and 100 seronegative samples. The sensitivity of samples with <14 days using FT-DBA was 94.7% which increased to 100% for samples >14 days. The overall detection sensitivity and specificity were 98.8% and 98%, respectively, whereas the overall PPV and NPV were 97.6% and 99%. Moreover, comparative analysis between ELISA and FT-DBA revealed clinical agreement of Cohen’s Kappa value of 0.944. Conclusion: The assay can confirm past SARS-CoV-2 infection with high accuracy within 2 minutes compared to ELISA. It can help track SARS-CoV-2 disease progression, population screening, and vaccination response.

Rubble stone masonry walls are widely diffused in most of the cultural and architectural heritage of historical cities. The mechanical response of such material is rather complicated to predict due to their composite nature. Vertical compression tests, diagonal compression tests, and shear-compression tests are usually adopted to experimentally investigate the mechanical properties of stone masonries. However, further tests are needed for the safety assessment of these ancient structures. Since the relation between normal and shear stresses plays a major role in the shear behavior of masonry joints, governing the failure mode, triplet test configuration was here investigated. First, the experimental tests carried out at the laboratory (LPMS) of the University of L'Aquila on stone masonry specimens were presented. Then, the triplet test was simulated by using the Total Strain Crack Model, which reflects all the ultimate states of quasi-brittle material such as cracking, crushing and shear failure. The goal of the numerical investigation was to evaluate the shear mechanical parameters of the masonry sample, including strength, dilatancy, normal and shear deformations. Furthermore, the effect of (i) confinement pressure and (ii) bond behavior at the sample-plates interfaces were investigated, showing that they can strongly influence the mechanical response of the walls.

In bioprocess development, the host and the genetic construct for a new biomanufacturing process are selected in the early developmental stages. This decision, made at the screening scale with very limited information about the performance of the selected cell factory in larger reactors, has a major influence on the performance of the final process. To overcome this, scaledown approaches are essential to run screenings that show the real cell factory performance at industrial like conditions. We present a fully automated robotic facility with 24 parallel mini-bioreactors that is operated by a model based adaptive input design framework for the characterization of clone libraries under scale-down conditions. The cultivation operation strategies are computed and continuously refined based on a macro-kinetic growth model that is continuously re-fitted to the available experimental data. The added value of the approach is demonstrated with 24 parallel fed-batch cultivations in a mini-bioreactor system with eight different Escherichia coli strains in triplicate. The 24 fed-batches ran under the desired conditions generating sufficient information to define the fastest growing strain in an environment with varying glucose concentrations similar to industrial scale bioreactors.

COVID-19 pandemic will continue to pose a major public health threat until vaccination-mediated herd immunity is achieved. Most projections predict vaccine will reach a large subset of the population late in 2021 or early 2022. In the meantime, countries are exploring options to remove strict lockdown measures and allow for society and the economy to return to normal function. One possibility is to expand on existing COVID-19 testing strategies by including large-scale rapid point of care diagnostic tests (POCTs). Currently, there is significant variability in performance and features of available POCTs, making selection and procurement of appropriate test for specific use case difficult. In this review, we have used the World Health Organization’s (WHO) recently published Target Product Profiles (TPPs) for specific use cases of COVID-19 diagnostic tests to screen for top-performing POCTs on the market. Several top-performing POCTs, based on clinical sensitivity/specificity, the limit of detection, and time to results, that meet WHO TPP criteria for direct detection of SARS-CoV-2 (acute infection), or indirect diagnosis of past infection (host antibodies) are highlighted here.

The presented study is focused on the impact of binding zones locations at immunochromatographic test strips into analytical parameters of multiplex lateral flow assay. Due to non-equilibrium conditions for such assays the duration of immune reactions influences significantly on analytical parameters, and the integration of several analytes into one multiplex strip may cause essential decrease of sensitivity. To choose the best location of binding zones, we have tested reactants for immunochromatographic assays of lincomycin, chloramphenicol, and tetracycline. The influence of the distance to the binding zones on the intensity of coloration and limit of detection (LOD) was rather different. Basing on the obtained data, the best order of binding zones was chosen. In comparison with non-optimal location the LODs were 5-10 fold improved. The final assay provides LODs 0.4, 0.4 and 1.0 ng/mL for lincomycin, chloramphenicol, and tetracycline, respectively. The proposed approach can be applied for multiassays of other analytes.

Equilibrium climate sensitivity (ECS) is the change in global mean temperature expected to result from doubling atmospheric CO2 concentration from pre-industrial levels. Extensive research during the past 40 years has not reduced the uncertainty associated with ECS. Sherwood et al. [1] applied Bayesian statistics to evidence from climate-process physics, historical observations and earlier proxies to reduce the range of ECS from 1.5 – 4.5 K to 2.6 – 4.1 K. This paper examines their methods and many of the assumptions they made. It also evaluates two additional periods in the Holocene to show that factors other than CO2 drove recent climate change. It identifies potential systematic errors resulting from adding non-equilibrium short-term adjustments to the radiative forcing of greenhouse gases and from underestimating the effects of solar irradiance, ocean currents and aerosols. These factors have resulted in estimates of the forcing by CO2 that far exceed the apparent effects in paleoclimate data.

The arrival of new developments in the field of power electronics circuit’s applications in power systems builds new control strategy to improve voltage quality for power grid by overcome interruptions. Wind energy resources are unconventional resources and get advanced problems to power grid when it is connected. Uncertainty of load sharing, peak energy management, climatic conditions, wind velocity and wind energy injected into power grid leads many of power quality problems on power grid based on the existing guidelines specified in IEC-61400 standard. This system plans efficient operation of DFIG to eliminate the voltage collapse and mismatch frequency to power grid. The DFIG connected diode rectifier and rotor side converter wind generator works as an Efficient Static Synchronous Compensator (E-SATCOM) for supplying the demand of reactive power for power grid to mitigate PQ problems. The benefit of using a combined controller was verified by simulink/Matlab and its simulated results used Doubly Fed Induction Generator (DFIG), wind Turbine. This simulation results gives good quality transient and stable state response to manage and support reactive power for both symmetrical and unsymmetrical faults in connection of grid codes to provide continuous quality of power supply, multiple wind generators are required for 140 bus power grid.

This study investigates the trend in monthly and annual rainfall, minimum and maximum temperature (T_min and T_max) using the Mann–Kendall (MK) test and Sen’s slope (SS) method and evaluates the significance of their variability for maize, sorghum and millet yields in northern Togo employing multiple regression analysis. The historical data of Kara, Niamtougou, Mango and Dapaong weather stations from 1977 to 2012 were used. Four non-parametric methods—Alexandersson’s Standard Normal Homogeneity Test (SNHT), Buishand’s Range Test (BRT), Pettitt’s Test (PT) and Von Neumann’s Ratio Test (VNRT)—were applied to detect homogeneity in the data. For the data which were serially correlated, a modified version of the MK test (pre-whitening) was utilised. Results showed an increasing trend in the annual rainfall in all four locations. However, this trend was only significant at Dapaong (p < 0.1). There was an increasing trend in T_max at Kara, Mango and Niamtougou, unlike Dapaong where T_max revealed a significant decreasing trend (p < 0.01). Similarly, there was an increasing trend in T_min at Kara, Mango and Dapaong, unlike Niamtougou where T_min showed a non-significant decreasing trend (p > 0.05). Rainfall in Dapaong was found to have increased (7.79 mm/year) more than the other locations such as Kara (2.20 mm/year), Niamtougou (4.57 mm/year) and Mango (0.67 mm). T_max increased by 0.13, 0.13 and 0.32 °C per decade at Kara, Niamtougou and Mango, respectively, and decreased by 0.20 per decade in Dapaong. Likewise, T_min increased by 0.07, 0.20 and 0.02 °C per decade at Kara, Mango and Dapaong, respectively, and decreased by 0.01 °C per decade at Niamtougou. Results of multiple regression analysis revealed nonlinear yield responses to changes in rainfall and temperature. Rainfall and temperature variability affects rainfed cereal crops production, but the effects vary across crops. The temperature has a positive effect on maize yield in Kara, Niamtougou and Mango but a negative effect on sorghum in Niamtougou and millet in Dapaong, while rainfall has a negative effect on maize yield in Niamtougou and Dapaong and millet yield in Mango. In all locations, rainfall and temperature variability has a significant effect on the cereal crop yields. There is, therefore, a need to adopt some adaptation strategies for sustainable agricultural production in northern Togo.