Due to its high power, high efficiency, low pollution, and compact size, permanent magnet synchronous motors (PMSMs) have been widely used in a variety of fields, including electric vehicles, aerospace, wind turbines, and marine devices which are used in renewable, sustainable, and environmentally friendly energy resources. However, in these practical scenarios, the motor operating conditions are complex and variable. Under high temperatures and high current conditions, PMSMs may experience demagnetization failures, not only leading to performance degradation but also inducing unexpected failures of the motors. To reduce the risk of unexpected losses caused by demagnetization faults and improve the safety and reliability of motor systems, it is necessary to apply automated monitoring of the magnet flux of the motor's permanent magnets and achieve real-time diagnosis of early demagnetization faults, ensuring the safe operation of the motor. This review article tries to summarize the current detecting methods of the automated monitoring of demagnetization faults in PMSMs. The main online monitoring technologies from both practical and academic perspectives were summarized and their benefits and challenges have been reviewed. Finally, the research trends and suggestions for future improvements are provided. This review article will not only shed light on the origins of the automated monitoring of demagnetization faults but also help to design highly effective and sustainable permanent magnet synchronous motors.

It's a method to achieve energy savings in single-phase active power greater than that obtained with the "Fan Law" in electric machines applied to ventilation. Quantitative analysis methods were based on electrotechnical techniques, practiced with the corresponding laboratory equipment on the working materials (three prototypes of electric machines). The results obtained from experimentation on the test bench were recorded in tables that collect data of formulas, values, and physical units. The discussion provides a comprehensive comparative study, mainly between power (watts), active energy consumption (kWh), and rotational speed (revolutions per minute). The permanent magnet synchronous motor (PMSM) with the coupling of an RL circuit design does mechanical work at its maximum speed of 3000 (RPM) with only 6.3 (Watts), which is equivalent to 25.2% of the active power required by the single-phase induction asynchronous motor (or shaded pole motor), which required 25 (Watts) to rotate at 1690 (RPM). This translates to 75% lower active power with a 44% superiority in speed, resulting in a 75% savings in single-phase active energy (measured in kWh). The same occurs when comparing it to the universal AC motor (with brushes and wound rotor) to maintain a speed of 3000 (RPM); since it consumes 64.8 (Watts), which is 90.3% more single-phase active energy than that required to achieve the same rotational speed as the permanent magnet synchronous motor (PMSM). The study was conducted on all motors with the same impeller blade diameter and under identical air temperature and atmospheric pressure conditions.

Treatment of neurological disease is hampered by the lack of validated specific and sensitive biomarkers, resulting in delayed diagnosis and nonspecific disease modifying therapies. For example, in ALS the lack of a sensitive and specific biomarker impedes the ability to administer a treatment prior to or at the onset of motor neuron dysfunction. Although viral or other infectious etiologies have been proposed as a contributing factor to neurodegeneration, it can be argued that these are casual and not causal associations. In the case of ALS, evidence for direct causality would require in vivo validation of specific nucleotide sequences of microbial origin which are known to be neuroinvasive with tropism for motor neurons, such as polio and non-polio. Several viral enteropathogens recapitulate the pathological events in sporadic ALS, including the ability to cleave TDP-43 resulting in accumulation of misfolded proteins in the cytoplasm. This review provides supporting evidence that motor neuron disease is causally related to specific enteroviruses and argues that prospective validation is imperative for effective prevention and treatment.

Abstract: The article proposes to consider the possibility of connecting the problems of engineering synthesis of frequency control systems for asynchronous electric drives with the basic provisions of the theory of identification of asynchronous electric motors based on the equations of a generalized AC electric machine.The article presents the results of experimental studies of load parrying processes in asynchronous electric drives with vector and scalar controls. These results indicate the absence of fundamental advantages as processes in a drive with vector control. This advantage should have manifested itself in a more efficient formation of the moment and fast transients. It is suggested that the reason for this is in too significant errors, assumptions and simplifications of the equations adopted in the derivation of vector control and which are its theoretical basis. A method is proposed for describing asynchronous electric motors by nonlinear transfer functions, which made it possible to formulate the principle of correction of electric drives and a method for assessing their efficiency.The article shows. that the correction based on the proposed nonlinear transfer functions of the induction motor is much more efficient than the traditional vector control, which was confirmed by detailed experiments and modeling. The results of the most important of which are given in the article. An assumption was made. that the advantage in efficiency is due to a more accurate identification of the dynamics of an asynchronous electric motor with a gear function instead of vector equations.

Neuromonitoring of the efferent nerve impulses transmission in the spinal cord tracts during surgical scoliosis treatment makes it possible to assess whether the functional status is deteriorating, affecting the procedure's safety. Is there any relationship between pre- and intraoperative motor evoked potentials recordings and does idiopathic scoliosis (IS) surgical correction improve directly the spinal efferent transmission? This study aimed to compare the results of surface recorded electromyography (EMG), electroneurography (ENG, M and F-waves), and especially motor evoked potentials (MEP) from tibialis anterior (TA) muscle bilaterally in 353 girls with the right idiopathic scoliosis (types 1A-4C according to Lenke classification). It has not yet been documented whether the results of MEPs recordings induced by transcranial single magnetic stimulus (TMS, pre – and postoperatively) and trains of electrical stimuli (TES; intraoperatively in T0-before surgery, T1 – after pedicle screws implantation, T2 – after scoliosis curvature distraction and derotation following two rods implantation) can be compared for diagnostic verification of improvement of the spinal neural transmission. The study also attempted to determine whether the constant level of optimal anesthesia during the certain surgical steps of scoliosis treatment affects the parameters of MEPs recorded during neuromonitoring procedures. No neurological deficits have been observed postoperatively. Values of amplitudes but not latencies in MEPs recordings evoked with TMS in IS patients compared before and after surgery indicated a slight improvement in the efferent transmission of neural impulses within the fibers of the spinal tracts postoperatively. Results of all neurophysiological studies in IS patients were significantly asymmetrical and recorded worse on the concave side, suggesting greater neurological motor deficits at p=0.04. This asymmetry had been significantly reduced following IS surgery. The surgeries in IS patients brought significant improvement (p=0.04) in parameters of amplitudes of sEMG recordings, however reflecting still the consequences of the neurogenic injury of TA muscle motor units. ENG studies results indicated the symptoms of the axonal type injury in peroneal motor fibers improved only on the concave side at p=0.04 in parallel with the significant improvement of F-waves parameters, which suggests that surgeries might result in the lumbar ventral roots decompression. There were not detected significant differences in amplitudes or latencies of MEPs induced with TMS or TES comparing the parameters recorded preoperatively (one day before surgery) and intraoperatively in T0. The amplitudes of TES evoked MEPs increased gradually at p=0.04 in the subsequent periods (T1 and T2) of observation. The significant reduction of MEPs latency at p=0.05 was observed only at the end of the IS surgery. Studies on the possible connections between the level of anesthesia fluctuations and the required TMS stimulus strength, as well as the MEPs amplitude changes measured in T0-T2 revealed lack of relationships. It is not likely that they could be the factors influencing the efferent transmission in spinal pathways beside the surgical procedures. Considering that MEPs amplitude parameter reflects the number of axons excited from the motor cortex and transmitting the efferent impulses via spinal descending tracts in the white matter, pre- (TMS evoked) and intraoperative (TES evoked) recordings are reliable for evaluating the patient’s neurological status before and during surgical scoliosis correction procedures. The results of this study indicate an agreement between preoperative and early-intraoperative evaluations with these both diagnostic methods. An increase of MEPs amplitude parameters recorded on both sides after scoliosis surgery proves immediate improvement of the total efferent spinal cord transmission. Considering comparative pre- and postoperative sEMG and ENG recordings it can be concluded that surgeries might directly result in the additional lumbar ventral roots decompression. Our results of the tests on the possible variability of the anesthesia level on the parameters of intraoperative recorded MEPs show no clear relationships. We can conclude that MEPs parameters changes are determined by the surgery procedures during neuromonitoring, not the anesthesia conditions if they are kept stable, which influences a decrease in the number of false-positive neuromonitoring warnings. Further studies on a larger population of patients with long-lasting observation postoperatively are required to confirm the presented conclusions on the direct influences of scoliosis surgery on improvement of the motor function in patients with IS.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

Motor imagery(MI)-based Brain-Computer Interfaces (BCI) have shown increased potential for the rehabilitation of stroke patients; nonetheless, their implementation in clinical practice has been restricted due to their low accuracy performance. To date, although a lot of research has been made in benchmarking and highlighting the most valuable classification algorithms in BCI configurations, most of them are using offline data and not from real BCI performance during the closed-loop (or online) sessions. Since rehabilitation training relies on the availability of an accurate feedback system, we surveyed articles of current and past EEG-based BCI frameworks who report the online classification of the movement of two upper limbs in both healthy volunteers and stroke patients. We found that the recently developed Deep Learning methods do not outperform the traditional machine learning algorithms. In addition, patients and healthy subjects exhibit similar classification accuracy in current BCI configurations. Lastly, in terms of neurofeedback modality, Functional Electrical Stimulation (FES) yielded the best performance compared to non-FES systems.

Humans can recombine thousands of different facial expressions. This variability is due to the ability to voluntarily or involuntarily modulate emotional expressions, which, in turn, depends on the existence of two anatomically separate pathways. The Voluntary (VP) and Involuntary (IP) pathways mediate the production of posed and spontaneous facial expressions, respectively, and might also affect the left and right sides of the face differently. This is a neglected aspect in the emotion literature, where posed expressions instead of genuine expressions are often used as stimuli. Two experiments with different induction methods were specifically designed to inves-tigate the unfolding of spontaneous and posed facial expressions of happiness along the facial vertical axis (left, right) with a high-definition 3D optoelectronic system. The results showed that spontaneous expressions were distinguished from posed facial movements as revealed by relia-ble spatial and speed key kinematic patterns in both experiments. Moreover, VP activation pro-duced a lateralization effect: compared with the felt smile, the posed smile involved an initial acceleration of the left corner of the mouth, while an early deceleration of the right corner oc-curred in the second phase of the movement, after the velocity peak.

Lead (Pb) is a toxic environmental heavy metal that induces serious clinical defect on all organs with the nervous system being the primary target. Curcumin is the main active constituent of turmeric rhizome (Curcuma longa) with strong antioxidant and anti-inflammatory properties. This study is aimed at evaluating the therapeutic potentials of curcumin on Pb-induced neurotoxicity. Thirty six male Sprague Dawley rats were randomly assigned into five (5) groups with 12 rats in the control (normal saline) and 6 rats for the lead treated group (LTG) (50 mg/kg lead acetate for 4 weeks), recovery group (RC) (50 mg/kg lead acetate for 4 weeks), treatment group 1 (Cur100) (50 mg/kg lead acetate for 4 weeks, followed by 100 mg/kg curcumin for 4 weeks) and treatment group 2 (Cur200) (50 mg/kg lead acetate for 4 weeks, followed by 200 mg/kg curcumin for 4 weeks) groups each. All experimental groups received the oral treatments through orogastric-tube on alternate days. Motor function was assessed using horizontal bar method while Pb concentration in the cerebellum of the rats were evaluated using ICP-MS techniques. Pb-administered rats showed significant decrease in motor scores, SOD activity with increase MDA levels and Pb concentration in their cerebellum with marked alterations in the histological architecture of the cerebellar cortex layers. However, treatment with curcumin improved the motor score, reduced Pb concentration in the cerebellum and ameliorates the markers of oxidative stress as well as restored the histological architecture of the cerebellum. The results this in study suggested that curcumin attenuates Pb-induced neurotoxicity via inhibition of oxidative stress and chelating activity.

Lead (Pb) is a toxic environmental heavy metal that induces serious clinical defect on all organs with the nervous system being the primary target. Curcumin is the main active constituent of turmeric rhizome (Curcuma longa) with strong antioxidant and anti-inflammatory properties. This study is aimed at evaluating the therapeutic potentials of curcumin on Pb-induced neurotoxicity. Thirty six male Sprague Dawley rats were randomly assigned into five (5) groups with 12 rats in the control (normal saline) and 6 rats for the lead treated group (LTG) (50 mg/kg lead acetate for 4 weeks), recovery group (RC) (50 mg/kg lead acetate for 4 weeks), treatment group 1 (Cur100) (50 mg/kg lead acetate for 4 weeks, followed by 100 mg/kg curcumin for 4 weeks) and treatment group 2 (Cur200) (50 mg/kg lead acetate for 4 weeks, followed by 200 mg/kg curcumin for 4 weeks) groups each. All experimental groups received the oral treatments through orogastric-tube on alternate days. Motor function was assessed using horizontal bar method while Pb concentration in the cerebellum of the rats were evaluated using ICP-MS techniques. Pb-administered rats showed significant decrease in motor scores, SOD activity with increase MDA levels and Pb concentration in their cerebellum with marked alterations in the histological architecture of the cerebellar cortex layers. However, treatment with curcumin improved the motor score, reduced Pb concentration in the cerebellum and ameliorates the markers of oxidative stress as well as restored the histological architecture of the cerebellum. The results this in study suggested that curcumin attenuates Pb-induced neurotoxicity via inhibition of oxidative stress and chelating activity.

The transportation sector is seeing an increased adoption rate of electric vehicles (EV), which comprise battery electric vehicles (BEV), hybrid electric vehicles (HEV) and plug-in hybrid electric vehicles (PHEV). This mode of transportation is likely to displace automobiles powered by internal combustion engines (ICE) in the nearest future, as indicated by the current trend. Each of the key EC components is home to a variety of technologies that are either currently in use or will be in the near future. Electric vehicles have the potential to have a significant impact on a variety of fields, including the economy, the energy infrastructure, and the natural environment. As a result of the production of carbon dioxide gas from the combustion of fossil fuels, transportation is the sector that is responsible for the second-highest amount of greenhouse gas emissions. Electric vehicles, often known as EVs, are getting a lot of attention as a potentially game-changing solution to this issue. It is possible for electric vehicles to produce fewer emissions of carbon dioxide (CO2) than conventional automobiles due to the fact that an electric motor serves as the vehicle's propeller rather than an internal combustion engine. EVs have the potential to become zero-emission vehicles if they are paired with renewable energy sources. This document presents an overview of the numerous types of EV drive circuits, covering their design as well as the benefits and drawbacks associated with each type. The current state of battery technology, particularly that pertaining to the batteries utilized in electronic vehicles, is discussed in this paper. This article also discusses electric motor efficiency, power density, fault tolerance, dependability, cost, and the best electric motor for EVs. Then, a thorough study of future EV implementation's obstacles and prospects is done. Charging times and battery performance are examples of technological challenges, but government regulation of EVs continues to be a substantial non-technical hurdle.

The stator winding insulation system is the most critical and weak part of the EMU's (electric multiple unit) traction motor. The effective diagnosis for stator ITSC (inter-turn short-circuit) faults can prevent the fault from expanding into phase-to-phase or ground short-circuits. The TCU(traction control unit) controls the traction inverter to output SPWM (sine pulse width modulation) excitation voltage when the traction motor is stationary. Three ITSC fault diagnostic conditions are based on different IGBTs control logic. The Goertzel algorithm is used to calculate the fundamental current amplitude difference Δi and phase angle difference Δθ of equivalent parallel windings under the three diagnostic conditions. The six parameters under the three diagnostic conditions are used as features to establish an ITSC fault diagnostic model based on random forest. The proposed method was validated using a simulation experimental platform for ITSC fault diagnosis of EMU traction motors. The experimental results indicate that the current amplitude features Δi and phase angle features Δθ change obviously with the increase of ITSC fault extent if the ITSC fault occurs at the equivalent parallel windings. The accuracy of the ITSC fault diagnosis model based on the random forest for ITSC fault detection and location both in train and test samples are 100%.

Learning dental procedures is a complex task involving the development of fine motor skills. The reported use of theories and/ or evidence for designing learning activities to develop the fine motor skills needed for dental practice is limited. The aim of this review is to explore the available body of knowledge related to learning fine motor skills in dentistry. Evidence from studies investigating motor skill learning highlights the negative impact of self-focus and self-regulation on learning outcomes, particularly during the early stages of learning. The development of activities and schedules that enable novices to demonstrate characteristics similar to experts, without the reported long period of ‘deliberate practice’, is clearly of value. Outcomes of learning implicitly are important in dentistry because working under stressful conditions is common, either during undergraduate study or in practice. It is suggested that learning implicitly in the simulation stage can reduce disrupted performance when transitioning to clinical settings. Therefore, further investigation of effective methods for learning dental fine motor skills is indicated, using approaches that result in robust performance, even under stressful conditions.

The link between language processing and motor systems has been the focus of increasing interest to Cognitive Neuroscience. Some classical papers studying Event Related Potentials (ERPs) induced by linguistic stimuli have found differences in electrophysiological activity when comparing action and non-action words; more specifically, a bigger p200 for action words. On the other hand, a series of studies have validated the use of a grip force sensor (GFS) to measure language-induced motor activity during both isolated words and sentence listening, finding that action words induce an augmentation in the grip force around 250-300 ms after the onset of the stimulus. The purpose of the present study is to combine both techniques to assess if the p200 is related to the augmentation of the grip force measured by a GFS. We measured ERP and GFS changes elicited by listening to action and non-action words while maintaining an active grasping task in 10 healthy subjects. Our results show that the amplitude of the p200 in central electrodes is correlated to the augmentation in the GFS around 300 ms induced by linguistic stimuli. To our knowledge, this is the first study where the electrophysiological activity and the changes in the grip force induced by auditory language processing are put together, opening new venues of interpretation for the sensorimotor interaction in language processing.

Objective: To evaluate the effects of left intraparietal sulcus (IPS) inhibition by repetitive transcranial magnetic stimulation (rTMS) on grip force modulation (GFM) for both hands during a unimanual task. Methods: GFM induced by manual action-verb listening was evaluated for each hand in a unimanual task, and the motor-evoked potentials (MEP) were recorded for both left and right hemispheres prior to and following the left IPS inhibition. Left IPS inhibition was obtained by rTMS (5 min of 1.0 Hz, 60% of maximal stimulator output) of the international 10–20 system P3 point. Seven healthy right-handed subjects were evaluated. Results: One-way repeated measures ANOVA found that MEP amplitude and duration increased following IPS inhibition in the left hemisphere and did not change in the right hemisphere. Language-induced modulation did not change in the left hemisphere, while it was significantly attenuated in the right hemisphere. Since IPS inhibition increased the left primary motor cortex (M1) excitability, the maintenance of language-induced modulation intensity suggests it was also attenuated. Conclusion: Left IPS inhibition increased left M1 excitability without changing right M1 excitability, while attenuating the language-induced GFM for both the left and right hands.

With the widespread use of electric machines there is a growing need to extract information from the machines to optimize their control systems and maintenance management. The present work shows the development of an embedded system to perform the monitoring of an squirrel cage induction motor rotor physical variables. The system comprises: circuit to acquire desirable rotor variable(s) value(s) and send it to the computer; a rectifier and power storage circuit that besides converting an alternating current in continuous also store energy for a certain amount of time to wait the motor engine shutdown; and magnetic generator that harvest energy from rotating field to power the circuits mentioned above. The embedded system is set on the rotor, making it difficult to power the system because it is rotating, problem solved with the construction of the magnetic generator eliminating the need of using batteries or collector rings and send data to the computer using a wireless NRF24L01 module. For the proposed system validation a temperature sensor (DS18b20) was used, variable known as the most important when identifying the need for maintenance and control systems. Tests were made getting satisfactory results proving the viability of using sensors on the rotor.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

This work proposes a new theoretical approach for the next generation of extremely efficient motors, whose impact will be substantial for future sustainable technological development. Building on well-known physical concepts, this approach introduces the concept of equilibrium of mutual retention, upon which a device remains in an equilibrium state between movement and attraction-repulsion. This new theoretical approach showed promising results in computer simulation experiments, indicating that the equilibrium of mutual retention can allow for a new way of modeling an extremely efficient motor. Finally, a theoretical efficiency analysis showed the need to expand the limits of some physical concepts already established.

In this paper, the design of a low cost portable ventilator with performance analysis have been done to solve the scarcity of respiratory ventilators for COVID-19 patients. The materials used to build the system are: DC motor, rotating disc and pneumatic piston. The system input is the patient heart beat and the output is volume of air to the patient lung with adjusted breathing rate. This ventilator adjusts the breathing rate to the patient depending on his heart beat rate. The performance analysis of this system have been done using Proportional Integral Derivative (PID) and Full State Feedback H2 controllers. Comparison of the system with the proposed controllers have been done using a step change and a random change of the patient heart beat and a promising result have been analyzed successfully.

Background. The markerless motion capture system (MLS) is a new technology that uses deep learning to detect body segments from digital images. This study tested the agreement between the MLS and a force-plate based system (FPS, “gold standard”) to quantify stability control and motor performance (MP) during gait initiation (GI). Methods. Healthy adults (young and elderly) and patients with Parkinson’s disease (PD) performed GI series at spontaneous and maximal velocity on an FPS while being filmed by an MLS. Signals from both systems were used to compute the peak of forward center-of-mass velocity (indicator of MP) and the braking index (BI, indicator of stability control). Results. Descriptive statistics indicated that both systems detected between-groups differences and velocity effects similarly, while a Bland-Altman (BA) plot anal-ysis showed that BI and MP mean biases were virtually zero in all groups and conditions. Bayes factor 01 indicated strong (for BI) and moderate (for MP) evidence that both systems provided equivalent values. However, trial-by-trial analysis of BA plots revealed the possibility of differ-ences > 10% between the two systems. Conclusion. Although non-negligible differences do occur, MLS appears to be as efficient as FPS in detecting PD and velocity condition effects on BI and MP

Background and Aims. Most research on Parkinson's disease (PD) focuses on describing symp-toms and movement characteristics. Studies rarely focus on the early detection of PD and the search for suitable markers of a prodromal stage. Early detection is important, so treatments that may potentially change the course of the disease can be attempted early on. While gait disturb-ances are less pronounced in the early stages of the disease, the prevalence, and severity increase with disease progression. Therefore, postural instability and gait difficulties could be identified as sensitive biomarkers. The aim was to evaluate the discriminatory power of the Trail-Walking Test (Schott, 2015) as a potential diagnostic instrument to improve the predictive power of the clinical evaluation concerning the severity of the disease and record the different aspects of walking. Methods. 20 older healthy (M = 72.4 years, SD = 5.53) adults and 46 older adults with PD and the motor phenotypes postural instability/gait difficulty (PIGD; M = 69.7 years, SD = 8.68) and tremor dominant (TD; M = 68.2 years, SD = 8.94) participated in the study. The participants performed a motor-cognitive dual task (DT) of increasing cognitive difficulty in which they had to walk a given path (condition 1), walk to numbers in ascending order (condition 2), and walk to numbers and letters alternately and in ascending order (condition 3). Results. With an increase in the cognitive load, the time to complete the tasks (seconds) become longer in all groups, F(1.23, 73.5) = 121, p < .001, ɳ2p = .670. PD-PIGD shows the longest times in all conditions of the TWT, F(2, 60) = 8.15, p < .001, ɳ2p = .214. Mutual interferences in the cognitive and motor domain can be observed. How-ever, clear group-specific patterns cannot be identified. A differentiation between the motor phenotypes of PD is especially feasible with the purely motor condition (TWT-M; AUC = . 685, p = 0.44). Conclusions. PD patients with PIGD must be identified by valid, well-evaluated clinical tests that allow a precise assessment of the disease's individual fall risk, the severity of the dis-ease, and the prognosis of progression. The TWT covers various aspects of mobility, examines the relationship between cognitive functions and walking, and enables differentiation of the motor phenotypes of PD.

Physical activity (PA) is a modifiable factor that may have an influence on the course of Parkinson’s disease (PD). This study aimed to apply a simple behavioral intervention to encourage PD sufferers to increase their everyday physical activity and assess which parameters of motor functions will be improved. The research covered 50 PD patients (28 men and 22 women) aged 40-81 years (65.38 ± 9.23), with a duration of the disease 2-4 years, in stages 1-3 on the Hoehn and Yahr scale. The patients were randomly divided into two groups: the experimental group with behavioral therapy, and the control group without intervention. During 12 weeks the patients from the experimental group had five phone conversations. Each conversation lasted 15 minutes and was an interview about the subjects’ physical activity in the last month. The results were assessed by the Timed Up and Go test (TUG), Unified Parkinson's Disease Rating Scale (UPDRS) – part III, FIR (Functional Index “Repty” – own modification of Functional Independence Measure (FIM)), Functional Ambulation Category (FAC) and International Physical Activity Questionnaire (IPAQ). The results showed that spontaneous physical activity increased in the experimental group and motor functions improved. Physical activity improvement depended on age, body mass index, and gender.

Surgical neurolysis is a procedure designed to liberate an injured nerve from scar tissue or adjacent structure, thereby facilitating nerve regeneration in cases of brachial plexus neuropathy (BPN). This study presents a case series of patients diagnosed with BPN who underwent surgical neurolysis. The primary focus was on the clinical assessment of recovery using the British Medical Research Council motor grading scale (BMRC). Additionally, a comprehensive literature review was conducted to analyze motor recovery outcomes related to surgical neurolysis for BPN. 18 patients with BPN who underwent surgical neurolysis where included. The results experienced a notable increase of 58% in muscle strength as assessed by the BMRC. The average preoperative state of 2.17±1.15 improved significantly to a postoperative condition of 3.44±1.34 (p = 0.003, d= 0.913) The systematic review identified 2298 articles which were selected for qualitative analysis, demonstrated that surgical neurolysis was associated with favorable motor recovery outcomes in 75.82% of the patients. Both the case series and the literature review reveal significant motor recovery following surgical neurolysis. It is crucial to conduct well-designed, adequately powered, randomized, and blinded clinical trials. Such studies will provide robust evidence to support or refute the utility of this approach in motor recovery.

In the last decades, the automatic recognition and interpretation of brain waves acquired by electroencephalographic (EEG) technologies have undergone remarkable growth, leading to a consequent rapid development of Brain Computer Interfaces (BCIs). EEG-based BCIs are non-invasive systems that allow communication between a human being and an external device interpreting brain activity directly. Thanks to the advances in neurotechnologies, and especially in the field of wearable devices, BCIs are now also employed outside medical and clinical applications. Within this context, this paper proposes a systematic review of EEG-based BCIs, focusing on one of the most promising paradigms based on Motor Imagery (MI) and limiting the analysis to applications that adopt wearable devices. This review aims to evaluate the maturity levels of these systems, both from the technological and computational points of view. The selection of papers has been performed following the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA), leading to 84 publications considered in the last ten years (from 2012 to 2022). Besides technological and computational aspects, this review also aims at systematically list experimental paradigms and available datasets in order to identify benchmarks and guidelines for the development of new applications and computational models.

The synuclein family consists of α-, β-, and γ-Synuclein (α-Syn, β-Syn, and γ-Syn), expressed in the neurons and concentrated in synaptic terminals. While α-Syn is at the center of interest due to its implication in the pathogenesis of Parkinson’s disease (PD) and other synucleinopathies, limited information exists on the other members. The current study aimed at investigating the biological role of γ-Syn controlling the midbrain dopamine (DA) function. We generated two different mouse models with i) γ-Syn overexpression induced by an adeno-associated viral vector and ii) γ-Syn knockdown induced by a ligand-conjugated antisense oligonucleotide, to modify the endogenous γ-Syn transcription levels in midbrain DA neurons. The progressive overexpression of γ-Syn decreased DA neurotransmission in the nigrostriatal and mesocortical pathways. In parallel, mice evoked motor deficits in the rotarod and impaired cognitive performance as assessed by novel object recognition, passive avoidance, and Morris water maze tests. Conversely, acute γ-Syn knockdown selectively in DA neurons facilitated forebrain DA neurotransmission. Importantly, modifications in γ-Syn expression did not induce the loss of DA neurons or changes in α-Syn expression. Collectively, our data strongly suggest that DA re-lease/re-uptake processes in the nigrostriatal and mesocortical pathways are partially dependent on SNc/VTA γ-Syn transcription levels, and are linked to modulation of DA transporter function, similar to α-Syn.

Permanent magnet synchronous motor (PMSM) AC servo system shows the characteristics of uncertainty, time-varying and non-linearity, which makes it difficult for traditional PID control to achieve ideal control effect. Fuzzy control has strong adaptability to the problems of parameter variation, non-linearity and model inaccuracy of the controlled object. Vector control strategy is used to study its control principle and the realization of SVPWM. Because the motor object has certain fractional order characteristics, the fuzzy parameter self-tuning PIλ control is chosen as the position regulator of servo motor. It combines the accuracy of fractional order PI control and the adaptability of fuzzy control. A simulation model of PMSM three-closed-loop system is built in MATLAB/Simulink environment. The results show that the control method is effective and can satisfy the trajectory tracking of servo control.

First of all the paper presents a solid solution of piezoelectric ceramic that was synthesized according to the general formula Pb(1-x)Srx(Ti0.48Zr0.52)(1-y)NbyO3 with x = 0.05 and y = 0.02, using wet ceramic processing technology and using an oxide mix as prime material. The effects of dopants (Sr2+ and Nb5+) on phase constitution, on microstructure and on the dielectric and piezoelectric properties were determinate. The Zr/Ti ratio was chosen near the morphotropic phase boundary of the PZT system in studied composition. The XRD data revealed that the PZT doped composition had tetragonal perovskite structure. Secondly the paper presents the design of the novel piezo-motor based on a surface wave which translates the linear extension of different piezoelectric segments of a piezoelectric cylinder into a rotational bending movement. This rotational bending of the piezoelectric cylinder is then transformed into a continuous rotation of the rotor through a calculated contact. The design of the motor takes advantage of the high piezoelectric constants of the developed material in an optimal way in order to increase the energetic efficiency. A brief mathematical model of electromechanical answer of piezoelectric materials is presented as it was used in the modeling of the material during the numerical simulations.

The formation of the required AC voltage level is currently one of the most important problems. An unstable voltage level can lead to the failure of domestic and industrial equipment, also to the appearance of a lighting equipment flicker effect, which can adversely affect the operating mode. In this regard, the development of AC voltage regulators that perform the function of stabilizers has become relevant. In turn, new topologies should be energy efficient and reliable, this can be achieved by reducing the number of semiconductor elements, which in turn will reduce losses and increase efficiency. In addition to voltage stabilization, AC voltage regulators have found application as soft-start devices for asynchronous motors, and have become competitors to frequency converters. The power level can vary from units to tens of kilowatts where such devices can be used. This paper provides a review of AC voltage regulators, which can be used both as soft starters and AC voltage stabilizers. The analysis of the circuits was carried out and the efficiency was evaluated through their total harmonic distortions (THD), power factor and efficiency coefficient. Experiments were also performed for a number of circuits, where their operating modes were evaluated. Eventually, all circuits were divided into full number of switches with two or more AC switches per phase, with a reduced number of switches, where one AC switch per phase and with low number of switches – with one complementary pair of AC switches for all three phases.

In this research, a model is presented to detect and monitor the rotor bar’s condition of large motors. This proposed model uses two diagnostic methods MCSA and ZCT, to extract the fault components. The input of the proposed model is only the motor current at two levels of 80% and 100% of the nominal motor load, which by using the two methods MCSA and ZCT and making changes in how to use them can be the disadvantages of other methods such as incorrect detection of rotor bars in Large motors with variable load, the harmonical stator voltage (or the presence of the drives) and asymmetric conditions. The extracted components are classified using neural network, instead of experimental and human resources constraints. Using this classification algorithm is high accuracy and the ability to implement in conventional processors. The proposed model has been trained andtested using currents of real large motor data and 96.87% accuracy using neural network to detect faults and monitor the online status of the rotor bars. On the other hand, the proposed model has been implemented in the industrial environment (FiroozkoohCement Factory) and has been able to correctly determine the rotor bars of 4 large suspicious motors announced by the factory technicians.

Background: Proteins targeted by the Ubiquitin Proteasome System (UPS) are identified for degradation by the proteasome, which has been implicated in the development of neuro-degenerative diseases. Major histocompatibility complex (MHC) molecules present peptides broken down by the proteasome and are involved in neuronal plasticity, regulating synapse number and axon regeneration in the central or peripheral nervous system during develop-ment and in brain diseases. The mechanisms governing these effects are mostly unknown, but evidence from different compartments of the cerebral cortex indicates the presence of im-mune-like MHC receptors in the central nervous system. Methods: We have used human induced pluripotent stem cells (iPSC) differentiated to neural stem cells and then to motor neurons as a developmental model to better understand the structure of the proteasome in developing motor neurons. We perform a proteomic analysis of starting human skin fibroblasts, their matching iPSC, differentiated neural stem cells and motor neurons that highlighted significant differences in the constitutive proteasome and immunoproteasome subunits during development towards motor neurons from iPSC. Results: Proteomic analysis showed that the catalytic proteasome subunits expressed in fi-broblasts differ to those in neural stem cells and motor neurons. Western blot analysis con-firmed the proteomic data, particularly the decreased expression of Beta5i (PSMB8) subunit immunoproteasome. Conclusion: The constitutive proteasome subunits are upregulated in iPSC from HFF and the immunoproteasome subunit beta 5i expression is higher in MN than NSC suggesting a im-munoproteasome phenotype in MN. The immunoproteasome may have implications on motor neuron development and neurodevelopmental diseases that warrants further investi-gation.

Objective: To investigate whether impaired plantar cutaneous vibration perception contributes to axial motor symptoms in Parkinson’s disease (PD) and whether anti-parkinsonian medication and subthalamic nucleus deep brain stimulation (STN-DBS), show different effects. Methods: Three groups were tested: PD patients on medication (PD-MED), PD patients on medication and additional STN-DBS (PD-MED–DBS), and healthy subjects (HS) as reference. Motor performance was analyzed using a pressure distribution platform. Plantar cutaneous vibration perception thresholds (VPT) were investigated using a customized vibration exciter at 30 Hz. Results: Motor performance of PD-MED and PD-MED–DBS was characterized by greater postural sway, smaller limits of stability ranges, and slower gait, due to shorter strides, fewer steps per minute, and broader stride widths compared to HS. Comparing patient groups, PD-MED–DBS showed better overall motor performance than PD-MED, particularly for the functional limits of stability and gait. VPTs were significantly higher for PD-MED compared to HS, which suggests impaired plantar cutaneous vibration perception in PD. However, PD-MED–DBS showed less impaired cutaneous vibration perception than PD-MED. Conclusion: PD patients suffer from poor motor performance compared to healthy subjects. Anti-parkinsonian medication in conjunction with STN-DBS seems to be superior for normalizing axial motor symptoms compared to medication alone. Plantar cutaneous vibration perception is impaired in PD patients, whereas anti-parkinsonian medication together with STN-DBS is superior for normalizing tactile cutaneous perception compared to medication alone. Consequently, based on our results and the findings of the literature impaired plantar cutaneous vibration perception might contribute to axial motor symptoms in PD.

Reliable motor control design is a critical part of the electric vehicle application. Control techniques and motor control devices play an important role in achieving system reliability. In this study, motor control devices have been proposed to implement control techniques in sensorless PMSM. Motor control devices including PWM signal generation by FPGA, gate driver circuit (GDC), and power inverter were developed to be integrated into single-stage motor control devices for sensorless motor control applications. Improvements in GDC design have been the focus to increase the performance of the motor control devices used. Switching losses due to the parasitic elements caused ringing switching behavior of the power inverter circuit, which reduces the performance when the system is integrated. Moreover, in the implementation of sensorless motor control using observer techniques, these conditions affect the accuracy of rotor position estimation, which uses the current or voltage information of the power converter as a variable in the observer design model. Therefore, a GDC design using IR2110 with additional ringing suppression circuit configuration was proposed for the application of motor device control topology to improve the performance of sensorless motor control system. Furthermore, the reduction of switching losses, reduction of current distortion, and accuracy of rotor position information were confirmed by experimental results.

Stroke is a major leading cause of chronic disability, often affecting patients’ motor and sensory functions. Functional magnetic resonance imaging (fMRI) is the most commonly used method of functional neuroimaging and allows the non-invasive study of brain activity. The time-dependent coactivation of different brain regions at rest is described as resting-state activation. As a non-invasive task-independent functional neuroimaging approach, resting-state fMRI (rs-fMRI) may provide therapeutically useful information on both the focal vascular lesion and the connectivity-based reorganization and subsequent functional recovery in stroke patients. Considering the role of prompt and accurate prognosis in stroke survivors along with the potential of rs-fMRI in identifying patterns of neuroplasticity in different post-stroke phases, this review provides a comprehensive overview of the latest literature regarding the role of rs-fMRI in stroke prognosis in terms of motor and sensory outcome. Our comprehensive review suggests that with the advancement of MRI acquisition and data analysis methods, rs-fMRI emerges as a promising tool to study the motor and sensory outcome in stroke patients and evaluate the effect of different interventions.

The characteristics of response to stressful situations depend on a complex of factors such as personality traits, emotional regulation, health state, features of the nervous system, motor functions and proprioception. In cases of disruption of the brain's dopamine system due to disease or chemotherapy, hormone discharge due to stress, changes in emotions and proprioception may occur. The aim of our study was to find the relationship of stress resilence in verbal test and individual differences performed in proprioceptive test in onco-patients, sportsmen and group of control; as well as to observe the differences between these groups in the verbal stress resistance and individual differences proprioceptive tests. The results showed that onco-patients were less resistant as per verbal stress resistance outcomes for a major part of variables compared to other groups. The sportsmen were superior in verbal Risk and Control dimensions compared to other groups; but less in Positive Affectiveness. The proprioceptive test perfomance revealed the only statistically significant difference in performance in the dimension related to Mood, showing more Pessimism in the sportsmen group, but more Optimism in the oncopatients at temperamental (or intrisinc) level. The obtained results can be used by psychologists, therapists, coach and healthcare when needed to attend the specific needs of public, being pateints or sportsmen, etc.

Electrical rotating machines like Induction Motors (IMs) are widely used in several industrial applications since their robust elements, provide high efficiency and give versatility in industrial applications. Nevertheless, the occurrence of faults in IMs is inherent to their operating conditions, hence, Inter-turn short-circuit (ITSC) is one of the most common failures that affect IMs and its appearance is due to electrical stresses leads to the degradation of the stator winding insulation. In this regard, this work proposes a diagnosis methodology for the assessment and detection of incipient ITSC in IMs, the proposed method is based on the processing of vibration, stator currents and magnetic stray-flux signals. Certainly, the novelty and contribution include the characterization of different physical magnitudes by estimating a set of statistical time domain features, as well as, their fusion and reduction through the Linear discriminant Analysis technique within a feature-level fusion approach. Furthermore, the fusion and reduction of information from different physical magnitudes leads to perform the automatic fault detection and identification by a simple Neural-Network (NN) structure. The proposed method is evaluated under a complete set of experimental data and the obtained results demonstrate that the fusion of information from different sources (physical magnitudes) allows to improve the accuracy during the detection of ITSC in IMs , the results make this proposal feasible to be incorporated as a part of condition-based maintenance programs in the industry.

The effects of hypothermia on neonatal encephalopathy may vary regionally, spatially, and cytopathologically in the gyrencephalic neocortex with manifestations potentially influenced by seizures that alter the severity and distribution of neuropathology. We developed a neonatal piglet survival model of hypoxic-ischemic (HI) encephalopathy and hypothermia with continuous encephalographic (cEEG) monitoring for seizures to study injury in neocortex. Neonatal piglets were randomized to naïve, HI-normothermia (NT), overnight hypothermia (HT) initiated 2 hours after HI, sham-NT, or sham-HT treatments. Some piglets within sham and HI groups received cEEG monitoring during recovery. Survival was 2-7 days (piglets were unmedicated and those with poor recovery and unresolving seizures were euthanized early); there was no differences in survival among groups (p&gt;0.078). Neuropathology was assessed by hematoxylin and eosin staining and immunohistochemistry for RNA Binding FOX-1 Homolog 3 (Rbfox3/NeuN). Normal and ischemic-necrotic neurons were counted (layers II-VI collectively) in somatosensory, motor, and prefrontal cortices, identified by cytoarchitecture and connectomics, and in inferior parietal cortex by layer. Seizure burden was determined. HI-NT piglets had reduced normal/total neuron ratio and increased ischemic-necrotic/total neuron ratio relative to naïve, sham-NT, and sham-HT piglets in anterior and posterior motor and somatosensory cortices. Frontal cortex was vulnerable in the prefrontal lateral bank after HI-NT with ischemic-necrosis. HI-HT piglets had higher normal/total neuron ratios and lower ischemic-necrotic/total neuron ratios than HI-NT piglets in anterior/posterior motor and somatosensory cortices. Total normal neuron density in layer III of inferior parietal cortex was reduced in HI-NT piglets compared to sham piglets and was protected by HT. Laminar analysis of Rbfox3 in somatosensory cortex revealed three types of neurons: Rbfox3-positive/normal, Rbfox3-positive/ischemic-necrotic, and Rbfox3-depleted. HI piglets had increased Rbfox3-depleted/total neuron ratio in layers II and III compared to sham-NT. Cortical neuron Rbfox3-depletion was partly rescued by HT. Seizure burden was more severe in HI piglets compared to sham piglets, but HI-NT and HI-HT piglets were similar. We conclude that 1) the neonatal piglet neocortex has a suprasylvian spatial vulnerability to HI and seizures; 2) HT protects against neuropathology in functionally different regions of the neonatal gyrencephalic neocortex; 3) neurons in neonatal neocortex have a limited cytopathology repertoire seen by H&amp;E staining; 4) higher seizure burden correlates with more ischemic-necrotic neurons in somatosensory cortex; 5) seizure presence associates with damage spread to inferior parietal cortex; 6) seizure presence is insensitive to HT, and 7) Rbfox3 immunophenotyping identifies a novel neuronal RNA splicing protein nuclear-depletion pathology that appears reversible by HT. This work demonstrates that HT protection of neocortex in neonatal HI is topographic and laminar, seizure unmitigating, and restores depleted neuronal RNA splicing factor.

In this paper, an attempt has been made to analyze the effect of spool port/ groove geometry on the pressure drop and chamber pressures which effect the performance parameters of the flow distributor valve. The work mainly involves formulation of detailed mathematical model of the valve and compare them on the same platform. For mathematical modelling, Matlab has been used. The size of the orifices is considered same throughout the model for better comparison. Initially the construction and functioning of flow distributor valve along with working principles of hydrostatic motor (Rotary Piston) is shown. Next shown the analytical analysis of area change and pressure drops due to different geometry of the spool valve ports. After that the computational fluid dynamics (CFD) analysis has been shown. A complete mathematical model to describe such flow distributor valve is developed after having a comprehensive knowledge of orifice characteristics, flow interactions based on valve geometry. Equations of flow through different orifices (fixed and variable area) of the valve have been developed based on the relationships obtained earlier.

Background: The vegetative state (VS)/unresponsive wakefulness syndrome (UWS) denotes brain-injured, awake patients who are seemingly without awareness. Still, up to 15% of these patients show signs of covert consciousness when examined by functional magnetic resonance imaging (fMRI) or EEG, which is known as cognitive motor dissociation (CMD). Most experts prefer the term unresponsive wakefulness syndrome to avoid the negative connotations associated with vegetative state and to highlight the possibility for CMD. However, the perception of VS/UWS by the public has never been studied systematically. Methods: Using an online crowdsourcing platform, we recruited 1297 participants from 32 countries. We investigated if vegetative state and unresponsive wakefulness syndrome might have a different influence on attitudes towards VS/UWS and CMD. Results: Participants randomized to be inquired about the vegetative state believed that CMD was less common (mean estimated frequency in unresponsive patients 38.07% ± SD 25.15) than participants randomized to unresponsive wakefulness syndrome (42.29% ± SD 26.63; p=0.016). Attitudes towards treatment withdrawal were similar. Most participants preferred unresponsive wakefulness syndrome (60.05%), although a sizeable minority favored vegetative state (24.21%; difference 35.84%, 95% CI 29.36 to 41.87; p<0.0001). Searches on PubMed and Google Trends revealed that unresponsive wakefulness syndrome is increasingly used by academics but not lay people.Discussion: Simply replacing vegetative state with unresponsive wakefulness syndrome may not be fully appropriate given that 1 of 4 prefer the first term. We suggest that physicians take advantage of the controversy around the terminology to explain relatives the concept of CMD and its ethical implications.

Background: Cervical myelopathy (CM) is a common cause of morbidity and disability in patients with mucopolysaccharidosis (MPS) and, therefore, early detection is crucial for best surgical intervention and follow-up. Transcranial Magnetic Stimulation (TMS) non-invasively evaluates the conductivity along the cortico-spinal tract, also allowing preclinical diagnosis and monitoring. Methods: motor evoked potentials (MEPs) to TMS were recorded in a group of 8 patients with MPS-related CM. Responses were obtained during mild tonic contraction through a circular coil applied over the “hot spot” of the first dorsal interosseous and tibialis anterior muscles, bilaterally. Central motor conduction time was estimated as the difference between MEP cortical latency and the peripheral motor conduction time by cervical or lumbar magnetic stimulation. Peak-to-peak MEP amplitude to cortical stimulation and right-to-left difference of each parameter were also measured. Results: TMS revealed abnormal findings from both upper and lower limbs compatible with axonal damage and demyelination in 6 of them. Notably, a subclinical cervical spinal disease was detected before the occurrence of an overt CM in two patients, whereas TMS signs compatible with a CM of variable degree persisted despite surgery in all treated subjects. Conclusions: TMS screening should be performed in MPS patients, before and after surgery.

The development trends of the modern world of power electronics dictate the requirements for the use of AC voltage converters as soft starters for induction motors. A direct connection of the motors to the mains voltage negatively affects both the motor itself and the mains system as a whole due to high starting currents values, which entail, as a rule, more frequent accidents and shorter the drive system service life. The paper presents a study of the control system of a multi-zone AC voltage regulator. The use of capacitive voltage dividers will also compensate for the consumed reactive power. The article analyzes the features of modern soft starters, describes the circuit design, presents a mathematical calculation by the method of algebraization of differential equations, a performed simulation modeling in Matlab/Simulink, and also an assembled experimental stand for further research. Particular attention is paid to the definition of the multizonality concept of the proposed converter and the analysis of the control method. The developed algorithm of the double-loop automatic control system will minimize the influence of induction motors on the mains voltage, and thus improve electromagnetic compatibility.

During the last decades, zebrafish (Danio rerio) has become one of the most important model organisms to study different physiological and biological phenomena. Research field of carbonic anhydrases (CAs) and carbonic anhydrase related proteins (CARPs) is not an exception in this. The best-known known function of CAs is the regulation of acid-base balance. However, studies performed with zebrafish, among others, have revealed important roles for these proteins in many other physiological processes, some of which have been unpredicted in the light of the previous studies and suggestions. Examples are roles in zebrafish pigmentation as well as motor coordination. Disruption of the function of these proteins may generate even lethal outcomes. In this review, we summarize the current knowledge of CA-related studies performed in zebrafish.

In this paper, the design and performance investigation of the permanent magnet machines have been done to increase the mechanical and electrical outputs improvement of the systems. A permanent magnet Dc motor (PMDM) and generator (PMDG) have been modelled and designed to improve the angular position and generated current respectively. In this work, augmentation based H 2 optimal and H infinity synthesis controllers have been designed as a controller for the two systems and a comparison between the proposed controller for tracking a reference inputs and a promising results have been obtained.

a sensorless control scheme based on novel power converging law sliding mode observer is suggested to realize the sensorless control for the permanent magnet synchronous motor (PMSM). Firstly, by introducing a new power converging law, the problem of slow converging speed/large chattering value dilemma in the conventional converging law is solved; Secondly, in view of the shortcomings of the conventional position and speed estimation algorithm, the high-frequency buffeting in the sliding mode observer will be expanded, a phase-locked loop (PLL) velocity and position estimation strategy is adopted to replace it. Finally, through Matlab/Simulink modeling and motor speed regulation platform experimental results, the sensorless position and speed estimation technology proposed in this paper can respond to the starting speed command of 1000 r/min within 0.05 s, and the starting process has no overshoot. When disturbed by 10Nm loading, the speed fluctuation value can be controlled within 1%.

(1) Background. Cognitive impairment in people with Multiple Sclerosis (MS) has been studied in relation to some clinical variables (e.g., motor disability and disease duration) and lifestyle fac-tors such as Cognitive Reserve (CR). However, only very few studies have considered the interac-tion of clinical variables and cognitive reserve in preserving the integrity of the neuropsychologi-cal profile. In this paper, we hypothesised that a higher level of CR might predict good cognitive efficiency by modulating the clinical outcome of the disease. (2) Methods. A sample of 100 partic-ipants with MS (age range 30-74), was recruited and assessed remotely with a questionnaire to measure CR and a cognitive screening test. Data were analysed through Generalized Additive Models. (3) Results. We found that the model analysing the interaction between CR and disease duration, and between CR and motor disability was able to explain a significant percentage of cognitive performance. In particular, higher levels of CR predicted better cognitive performance despite long disease duration, unless the motor disability was severe. (4) Conclusion. This study highlights the crucial role of CR in modulating cognitive efficiency in people with MS.

Nowadays brushless DC motors (BLDCMs) are becoming indispensable components as the electrification revolution in the mobility industry is happening. Electric kick scooters, so-called e-scooters, are among these micro-mobility vehicles which are powered by these motors. Due to the uncertain and nonlinear features, the controller performance developed for these motors degrades. For these reasons, a chattering-reduced cascaded Sliding Mode Control (SMC) scheme to effectively track reference motor speed in the outer loop by eliminating torque ripples in the inner loop current control was designed. Field-oriented Control (FOC) methodology was used to implement the SMC in the BLDCM. An exponential reaching law algorithm was proposed for sliding surfaces of the inner and outer loop controllers. The suitability and performance of electric scooter-hub motors were analyzed in terms of traction control. A cascaded speed and torque controller produced significantly favorable results representing minimized torque and current ripples, and operation over a wide speed range.

This research work deals hybrid control system based integrated Cuk converter fed brushless DC motor (BLDCM) for power factor correction. In this work, moth-flame optimization (MFO) and fuzzy logic controller (FLC) has been combined and moth –flame fuzzy logic controller (MFOFLC) has been proposed. Firstly, the BLDC motor modelling is composed with power factor correction (PFC) based integrated Cuk converter and BLDC speed is regulated using variable DC-Link inverter voltage which makes low switching operation with less switched losses. Here, with the use of switched inductor, the task and execution of proposed converter is redesigned. The DBR (diode bridge rectifier) trailed by proposed PFC based integrated Cuk converter operates in discontinuous inductor conduction mode(DICM) for achievement of better power factor.MFO is exhibited for gathering of dataset from the input voltage signal. At that point separated datasets is send to FLC to improve the updating function and minimization of torque ripple. However, our main objective is to assess adequacy of proposed method, the power factor is broke down. The execution of the proposed control methodology is executed in MATLAB/Simulink working platform and the display is assessed with the existing techniques.

The practical problem-solving of incidental unreliability of intraoperative neuromonitoring may be the simultaneous neurophysiological recording and the inspection of the surgical field through the camera (the "Real-time neuromonitoring" concept). This would allow the immediate warning of the surgeon on the possibility of the spinal structures insult during but not after the application of the standard procedures in scoliosis surgery (the “Interactive verbal surgeon-neurophysiologist neuromonitoring" concept). This study aimed to compare the advantages, utility, reliability, and time-consuming of both intraoperative neuromonitoring scenarios using non-invasive and innovative recordings from peroneal nerves (PER) versus tibialis anterior muscles (TA) with surface electrodes of motor evoked potentials (MEP) bilaterally as a result of transcranial magnetic (TMS) or electrical (TES) stimulations. Studies were performed in two similar groups ("Real-time neuromonitoring", N=60 and "Interactive verbal sur-geon-neurophysiologist neuromonitoring", N=60) of patients treated surgically because of mainly Lenke 2 type idiopathic scoliosis (IS) pre- (T0), intra- (T1 – before surgical procedures, T2 – after surgical procedures) and postoperatively (T3) as well as in healthy volunteers (N=60, Control). The cumulative parameters of MEP amplitudes and latencies recorded from PER compared to those recorded from TA in healthy volunteers were approximately 67% (1100µV) lower at p=0.007 and 10.6% shorter (3.1 ms) at p=0.04, respectively. A similar trend was also observed in patients from both groups at each follow-up stage. MEP recordings from TA and PER in patients of both groups differed similarly in T0-T3 compared to controls at p=0.008-0.04. MEP parameters in all patients induced by TMS (T0) and TES (T1) did not differ. The parameters of MEP amplitudes recorded from TA and PER intraoperatively in T1 and T2 differed at p=0.04-0.03, indicating the bilateral improvement of neural spinal conduction due to the surgical intervention. Parameters of TMS-induced MEP amplitudes in T3 further increased bilaterally compared to the tests recorded in T0 at p=0.03-0.02. In both groups of patients, an average 51,8 BIS level of anaesthesia minimally affects the variability of the MEP amplitude, especially in PER recordings when ap-plied TES strength was at 98.2 mA. The number of MEP parameter fluctuations, mainly the amplitudes decreasing, was strictly associated with the neurophysiologist's warnings due to transpedicular screws implantation, corrective rods implantation, distraction, derotation, and compression procedures, respectively; at p=0.04-0.03 more in patients from the “Interactive S-N neuromonitoring” group. The average duration of the surgery was significantly shorter (p=0.04) by about 1 hour in the "Real-time neuromonitoring" group. The number of two-way communications between the surgeon and neurophysiologist and vice versa in the "Real-time neuromonitoring" group was reduced by approximately half at p=0.008. The study's results prove the advantages of using the "Real-time neuromonitoring" procedure in increasing safety and non-invasiveness, shortening the time, and lowering the costs of surgical treatment of patients with pathological lateral curvature of the spine. The modifications of the MEP nerve conduction recording technology with surface electrodes from nerves presented in this study enable precise and reliable information on the patient's neurological condition at every stage of applied surgical procedures, even in conditions of slight fluctuations in the anaesthesia.

Flux-switching permanent magnet (FSPM) motors have gained increasing attention in the electric vehicles (EVs) applications due to the advantages of high power density, high efficiency. However, the heat sources of both permanent magnet (PM) and armature winding are located on the limited stator space in the FSPM motors, which may result in the PM overheated and irreversible demagnetization caused by temperature rise and it is often ignored in the conventional thermal analysis. In this paper, a new electrical-thermal two-way coupling design method is proposed to analyze the electromagnetic performances, where the change of PM material characteristics under different temperatures is taken into consideration. Firstly, the motor topology and design equations are introduced. Secondly, the demagnetization curves of PM materials under different temperatures are modeled due to PM materials are sensitive to the temperature. And based on the electrical-thermal two-way coupling method, the motor performances are evaluated in details, such as the load PM flux linkage and output torque. Then, the motor is optimized, and the electromagnetic performances between initial and improved motors are compared. Finally, a prototype motor is manufactured, and the results are validated by experimental measurements.

Recently, SMR (Small Modular Reactor) is expected to be able to operate flexibly in conjunction with a high renewable energy penetration grid as a result of improved safety and easy power control compared to large nuclear power plants. SMRs such as South Korea’s System-integrated Modular Advanced ReacTor (SMART) are designed to use canned motors (CMs) for their reactor coolant pumps (RCPs) to enhance safety. The CMs passively enhance the reactor’s safety by preventing leakage of radioactive reactor coolant. However, with motor sizes designed to be as small as possible, and the increased air gap of CMs between stator and rotor, starting torque may be insufficiently small compared to that of similar sized induction motors (IMs). Thusly, CMs may require variable frequency drives (VFDs) to start. This paper compares the torque characteristics of CMs with those of IMs for SMART’s RCPs. ETAP is then used to perform motor starting analysis for CMs started with and without VFDs. The results are presented and analyzed to find out if the VFDs deal with the CM starting torque issue.

Background: Given that VR is applied in multiple domains, understanding the effects of cybersickness on human cognition and motor skills and the factors contributing to cybersickness gains urgency. This study aimed to explore the predictors of cybersickness and its interplay with cognitive and motor skills. Methods: 30 participants, 20-45 years old, completed the MSSQ and the CSQ-VR, and were immersed in VR. During immersion, they were exposed to a roller coaster ride. Before and after the ride, participants responded to CSQ-VR and performed VR-based cognitive and psychomotor tasks. Post VR session, participants completed the CSQ-VR again. Results: Motion sickness susceptibility, during adulthood, was the most prominent predictor of cybersickness. Pupil dilation emerged as a significant predictor of cybersickness. Experience in videogaming was a significant predictor of both cybersickness and cognitive/motor functions. Cybersickness negatively affected visuospatial working memory and psychomotor skills. Overall cybersickness’, nausea and vestibular symptoms’ intensities significantly decreased after removing the VR headset. Conclusions: In order of importance, motion sickness susceptibility and gaming experience are significant predictors of cybersickness. Pupil dilation appears as a cybersickness’ biomarker. Cybersickness negatively affects visuospatial working memory and psychomotor skills. Cybersickness and its effects on performance should be examined during and not after immersion.

This study examines the impact of chainsaw chain type and tree species on the concen-tration of inhalable wood dust generated during motor-manual harvesting in forested areas. The chainsaw chain is a critical component, contributing not only to productivity but also to the oper-ator's health and safety. Wood dust creation during harvesting operations poses significant risks and necessitates careful attention due to its potential health effects. We investigated the effects by conducting real-world measurements of inhalable dust within the operator's breathing zone during forestry work. Two different chain types were evaluated: the commonly used 3/8" pitch chain (conventional chain) and the 0.325" pitch chain. Additionally, measurements were taken for three tree species: beech, oak, and pine (including both live and standing dead trees after a fire). Results showed that, overall, using the conventional 3/8" chain type yielded the highest concentration of wood dust for all three tree species. Notably, the highest wood dust concentration was observed in the burned Pinus brutia cluster, also with the 3/8" chain pitch. These findings emphasize the im-portance of understanding how chain type and tree species contribute to wood dust levels and provide valuable insights for enhancing operator health and safety during motor-manual har-vesting operations

The purpose of this study is to investigate the impact of the voltage drop of a three-phase voltage source inverter in driving brushless motors. This study also proposes an enhanced Field Oriented Control scheme that accounts for the inverter voltage drop enabling efficient drive at very low motor-speeds. Experimental results are provided to verify the theoretical study and the proposed control scheme.

Diffuse optical tomography (DOT) technology enables a differentiation between oxyhemoglobin (HbO) and deoxyhemoglobin (HbR) in the sensory and motor cerebral gyri, resulting in greater sensitivity for cerebral activation compared to functional magnetic resonance imaging (fMRI). Here, we introduce a novel approach where functional regions of interest (ROIs) are created based on the specific signal behavior observed in DOT measurements, in contrast to the conventional use of structural-ROIs obtained from anatomical information. The generation of cerebral activation maps involves using the general linear model (GLM) to compare the outcomes obtained from both the functional and structural ROI approaches. DOT-derived maps are then compared with maps derived from fMRI datasets considered the gold standard for assessing functional brain activity. The results obtained demonstrate the effectiveness of employing functional ROIs to improve the spatial location of functional activations in the sensory and motor cerebral gyri by leveraging the neural synchronization data provided by DOT. Furthermore, this methodology simplifies data processing in animal models, where anatomical differences compared to the human head can pose challenges. By incorporating functional ROIs prior to GLM application, this study offers enhancements to DOT analysis techniques and broadens its applicability in both human and animal models.

Concatemeric viral DNA is packaged into Bacteriophage P22 procapsids via a headful packaging mechanism mediated by a molecular machine consisting of small (gp3) and large (gp2) terminase subunits. Although a negative stain reconstruction exists for the terminase holoenzyme, it is not clear how this complex binds dodecameric portal protein located at a 5-fold mismatch vertex. Herein, we describe new assemblies for the holoenzyme. Both native mass spectrometry and transmission electron microscopy reveal that the P22 terminase complex adopts three main assemblies, which include a nonameric S-terminase bound to two L-terminase 1(gp3)9:2(gp2), two nonameric S-terminase bound to five L-terminase 2(gp3)9:5(gp2), and three nonameric S-terminase bound to seven L-terminase 3(gp3)9:7(gp2). Native agarose gel electrophoresis shows that the terminase complex interacts with procapsid with mild crosslinking. These results herein illustrate the P22 terminase complex can adopt a variety of confirmations and assembly states.

Brain-computer interfaces (BCI) from electroencephalography (EEG) provide a practical approach to support human-technology interaction. In particular, motor imagery (MI) is a widely-used BCI paradigm that guides the mental trial of motor tasks without physical movement. Here, we present a deep learning methodology, named Kernel-based Regularized EEGNet (KREEGNet), leveled on Centered Kernel Alignment and Gaussian Functional Connectivity, explicitly designed for EEG-based MI classification. The approach proactively tackles the challenge of intra-subject variability brought on by noisy EEG records and the lack of spatial interpretability within end-to-end frameworks applied for MI classification. KREEGNet is a refinement of the widely accepted EEGNet architecture, featuring an additional kernel-based layer for regularized Gaussian functional connectivity estimation based on CKA. The superiority of KREEGNet is evidenced by our experimental results from binary and multi-class MI classification databases, outperforming the baseline EEGNet and other state-of-the-art methods. Further exploration of our model’s interpretability is conducted at individual and group levels, utilizing classification performance measures and pruned functional connectivities. Our approach is a suitable alternative for interpretable end-to-end EEG-BCI based on deep learning.

The multifarious internal workings of organisms are difficult to reconcile with a single feature defining a state of ‘being alive’. Indeed, definitions of life rely on emergent properties (growth, capacity to evolve, agency) only symptomatic of intrinsic functioning. Empirical studies demonstrate that biomolecules including ratcheting/rotating enzymes, ribozymes and pigment molecules undergo repetitive conformation state changes driven by energy absorption, excitation and relaxation. They exhibit disparate structures, but govern processes relying on directional physical motion (DNA transcription, translation, ATP synthesis, cytoskeleton transport, photosynthetic resonance energy transfer) and share the principle of repetitive uniplanar conformation changes driven by thermodynamic gradients, producing dependable unidirectional motion: ‘heat engines’ exploiting thermodynamic disequilibria to perform work. Recognition that disparate biological molecules share a heat engine principle governing directional motion, working in self-regulating networks, allows a mechanistic definition: life is a self-regulating process whereby matter undergoes cyclic, uniplanar conformation state changes that convert thermodynamic disequilibria into directed motion, performing work that locally reduces entropy. ‘Living things’ are structures including autonomous networks of units operating on the heat engine principle. Death is loss of integrated heat engine function. These principles are independent of any specific chemical environment, and can be applied to other biospheres.

This article presents a harmonic analysis of the stator currents of a squirrel-cage in-15 duction motor fed by a voltage source inverter with PWM space vector control (SV-PWM). The 16 influence of PWM switching frequency and dead time (dead-band) of controlled transistors on 17 THD and electromagnetic torque ripple is shown. The aim is to determine the lowest switching 18 frequency of the transistors for which the drive will operate correctly. Characteristics were de-19 termined as functions in the form of THD ( ), where the least square approximation was 20 used for stator current measurements when the PWM switching frequency is changed. The ap-21 proximations were realized for simulation and experimental results. To clarify the results, the 22 operation of hardware PWM circuits in microcontrollers was analyzed.

The construction of molecular robotic-like objects that imitate living things is an important challenge for current chemists. Such molecular devices are expected to perform their duties robustly to carry out mechanical motion, process information, and make independent decisions. Dissipative self-organization plays an essential role in meeting these purposes. To produce a micro-robot that can perform the above tasks autonomously as a single entity, a function generator is required. Although many elegant review articles featuring chemical devices that mimic biological mechanical functions have been published recently, the dissipative structure, which is the minimum requirement, has not been sufficiently discussed. This article aims to show clearly that dissipative self-organization is a phenomenon involving autonomy, robustness, mechanical functions, and energy transformation. Moreover, the author details the recent experimental results of an autonomous light-driven molecular device that achieves all of these features. In addition, a chemical model of cell-amplification is also discussed to focus on the generation of hierarchical movement by dissipative self-organization. By reviewing this research, it may be perceived that mainstream approaches to synthetic chemistry have not always been appropriate. In summary, the author proposes that the integration of catalytic functions is a key issue for the creation of autonomous microarchitecture.

Nanoparticles (NP), Nanoaerosols (NA), ultrafine particles (UFP), and PM0.1 (particles with a diameter ≤ 0.1 µm or 100 nm) are interchangeably used in the field of atmospheric studies. PM0.1 are emitted from both natural and anthropogenic sources. The main emission sources of PM0.1 are combustion processes, including biomass and fossil fuel. Moreover, secondary formation via atmospheric photochemical reactions can also occur depending on meteorological conditions and the suspended pollutant species. Identifying the physical and chemical characteristics and spatial and temporal variations is vital in terms of understanding the effect of NPs on the environment, the global climate, and human health risks. This review article summarizes recent research on PM0.1 in Thailand. The review involves peer-reviewed papers from Scopus and the Web of Science databases, and includes the most recently published articles in the past ten years (2013-2022). UFPs mainly come from the combustion processes such as motor vehicles. The high mass concentration of PM0.1 that occurs during the dry season in which open fires depend on the specific region of Thailand. Particulate pollution from local and cross-border countries also needs to be considered in terms of the concentrations of ambient nanoparticles. The overall conclusions reached will likely have a beneficial long-term impact on achieving a blue sky over Thailand through the development of coherent policies and managing new air pollution challenges and sharing knowledge with a broader audience.

In-wheel motor vehicles are gaining attention as a new type of electric vehicle due to their efficient power units located inside each wheel hub. However, they are more susceptible to wheel resonance due to the increase in unsprung mass caused by the motor's weight. This can result in decreased both the ride comfort and driving stability. To resolve this issue, this study aims to apply an optimal switching controller with a semi-active n actuator; magnetorheological (MR) damper. For the implementation of the optimal switching controller, a road type classification is also carried out. An acceleration sensor is used for road type classification, and control logics include a ride comfort controller; the linear quadratic regulator (LQR _Paved Road) and a wheel motion controller (LQR_Off Road) for improved driving stability. For paved roads, the LQR_Paved Road control input is applied to the MR damper. However, if a road type prone to wheel resonance is detected, the control logic switches to the LQR_Off Road. During the transition, a weighted average of both LQR_ Paved Road and LQR_Off Road control input is applied to the actuator. Computer simulations are undertaken to evaluate vibration control performance, including the ride comfort and driving stability at various road profiles.

This paper presents a novel real time control strategy on four-wheel independent steering system for electric vehicle with stepper motors using neural networks combined with fuzzy logic. The control of the four wheels is based on a variation of Hopfield Neural Network (VHNN) method, in which the input is the error of each steering motor and the output is processed by a hyperbolic tangent function (HTF) feeding the fuzzy logic controller (FLC), which ultimately drives the stepper motor. The whole system is made up of the four aforementioned blocks where they work in sync and inseparable from each other with the common goal of driving all the steering stepper motors at the same time. Simulation results demonstrate that the proposed control method has strong robustness and practicability under different angles and speeds.

Optical “fingerprints” are widely used in chemometrics-assited recognition of samples of different nature. An emerging trend in this area is the transition from obtaining "static" spectral data to reactions occurring over time. The indicator reactions are usually carried out in aqueous solutions; in this study we have developed the reactions that occur in an organic solvent, which makes it possible to recognize fat-soluble samples. In this capacity, we used 5W40, 10W40 and 5W30 motor oils of 4 manufacturers, totally 6 samples. The procedure involved mixing of the dye, sample, and reagents (HNO3, HCl, or t-butyl hydroperoxide) in ethanolic solution in a 96-well plate and measuring absorbance or near-IR fluorescence intensity every several minutes during 20–55 min. The obtained photographic images were processed by linear discriminant analysis (LDA) and k-nearest neighbors algorithm (kNN). The discrimination accuracy was evaluated by using the validation procedure. Reaction of oxidation of a dye with nitric acid allowed to recognize all 6 samples with 100% accuracy by LDA. Merging data of 4 reactions that did not provide complete discrimination ensured an accuracy of 93% by kNN technique. The developed indicator systems have good prospects for the discrimination of other fat-soluble samples. Overall, the results confirm the viability of the kinetic-based discrimination strategy.

In order to realize the tram's low-floor structure, most of the trams that have been recently introduced adopt an independently rotating wheelset. In the case of trains driving in two regions with different gauges, an independently rotating wheelset may be applied to utilize the variable track technology. Since the independent rotation type wheelset has no rotational restraint of the left and right wheels, the difference in rotational speed between the outer and inner wheels occurs naturally during curved driving, and it is applied to railroad vehicles traveling in steep curve sections because it smoothly drives curved driving. However, the longitudinal creep force and the lateral restoring force are weakened as the left and right rotational constraints disappear. Lack of transverse direction restoring force weakens stability while causing continuous flange contact driving or zigzag phenomenon against disturbance. Under the conditions of driving in a steep curve, these railway vehicles generate excessive wear, noise, and lateral pressure, as well as deterioration of ride comfort and derailment. In order to overcome these drawbacks, a method has been proposed in which the torque of a motor mounted on each wheel is individually controlled to generate lateral restoring force or to improve driving performance through lateral displacement control using a yaw moment. In this paper, development using HILs was performed to check the performance and stability of the individual motor torque control technology before verifying by applying the individual motor torque control to the actual vehicle. HILs were constructed by combining a real-time dynamic analysis model of a railway vehicle with a drive motor to which real individual motor control was applied. Under the conditions of driving the test track where the actual test vehicle was tested, the analysis of the driving characteristics and the control characteristics of the disturbance was performed to confirm the proposed individual motor torque control performance.

Amyotrophic lateral sclerosis (ALS) is also called "motor neuron disease”. In this review, we propose that ALS is not just a neuromotor disorder, but begins as a disorder of P53-modulated skeletal muscle metabolism, leading to failures at the energy state of the cells, incorrect redox states, motor denervation, and a loss of muscle fibers. Motoneurons die as a consequence of the lack of muscular feedback, and the oligomeric TDP43 aggregates progressively and relentlessly lead to mistakes in peripheral immune self-tolerance sustained over time. An effective treatment has not been found for this devastating pathology, as for 152 years the target has not been accurately defined. Scientists and doctors should consider new knowledge regarding ALS and consider immunomodulatory therapies that, based on genetic analysis and symptoms, can be combined with compounds that regulate metabolism and promote the elimination of useless organelles and cells. What if ALS could be cured as a result of seeing motor neuron disease differently? This review aims to develop that goal and change the paradigm of our understanding of ALS.

Motor functions are deteriorated by aging. Some conditions may magnify this deterioration. To examine whether hemodialysis (HD) process would negatively impact gait and balance beyond diabetes condition among mid-age adults (48-64 years) and older adults (65+ years). One hundred and ninety-six subjects (age=66.2±9.1 years, body-mass-index=30.1±6.4 kg/m², female=56%) in 5 groups were recruited: mid-age adults with diabetes undergoing HD (Mid-age HD+, n=38) and without HD (Mid-age HD-, n=40); older adults with diabetes undergoing HD (Older HD+, n=36) and without HD (Older HD-, n=37); and non-diabetic older adults (Older DM-, n=45). Gait parameters (stride velocity, stride length, gait cycle time, and double support) and balance parameters (ankle, hip, and center of mass sways) were quantified using validated wearable platforms. Groups with diabetes had overall poorer gait and balance compared to the non-diabetic group (p<0.050). Among people with diabetes, the HD+ had significantly worsened gait and balance when comparing to the HD- (Cohen’s effect size d=0.63-2.32, p<0.050). Between-group difference was more pronounced among older adults with the largest effect size observed for stride length (d=2.32, p<0.001). Results suggested that deterioration in gait speed among the HD+ was correlated with age (r=-0.440, p<0.001), while this correlation was diminished among the HD-. Interestingly, results also suggested that poor gait in the Older HD- related to poor balance, while no correlation was observed between poor balance and poor gait among the Older HD+. Using objective assessments, results confirmed that the presence of diabetes can deteriorate gait and balance, and this deterioration can be magnified by HD process. Among non-HD people with diabetes, poor static balance described poor gait. However, among people with diabetes undergoing HD, age was a dominate factor describing poor gait irrespective of static balance. Results also suggested feasibility of using wearable platforms to quantify motor performance during routine dialysis clinic visits. These objective assessments may assist in identifying early deterioration in motor function, which in turn may promote timely intervention.

Monocarboxylate transporter 8 (MCT8) and organic anion-transporting polypeptide 1C1 (OATP1C1) are thyroid hormones (TH) transmembrane transporters relevant for the availability of TH in neural cells, crucial for their proper development and function. Mutations in MCT8 or OATP1C1 result in severe disorders with dramatic movement disability related to alterations in basal ganglia motor circuits. Mapping the expression of MCT8/OATP1C1 in those circuits is necessary to explain their involvement in motor control. We studied the distribution of both transporters in the neuronal subpopulations that configure the direct and indirect basal ganglia motor circuits using immunohistochemistry and double/multiple labeling immunofluorescence for TH transporters and neuronal biomarkers. We found their expression in the medium-sized spiny neurons of the striatum (the receptor neurons of the corticostriatal pathway), and in various types of its local microcircuitry interneurons, including the cholinergic. We also demonstrate the presence of both transporters in projection neurons of intrinsic and output nuclei of the basal ganglia, motor thalamus and nucleus basalis of Meynert, suggesting an important role of MCT8/OATP1C1 for modulating the motor system. Our findings suggest that a lack of function of these transporters in the basal ganglia circuits would significantly impact motor system modulation, leading to clinically severe movement impairment.

Biosensors and wearable sensor systems with transmitting capabilities are currently developed and used for the monitoring of health data, exercise activities, and other performance data. Unlike conventional approaches, these devices enable convenient, continuous, and unobtrusive monitoring of a user’s behavioral signals in real time. Examples include signals relative to hand an finger movement/pressure control reflected by individual grip force data. As will be shown here, these directly translate into task, skill and hand-specific (dominant versus non-dominant hand) grip force profiles for different measurement loci in the fingers and palm of the hand. On the basis of thousands of sensor data from multiple sensor locations, individual grip force profiles of an task expert, a trained user and a highly proficient user (expert) performing an image-guided and robot-assisted precision task with the dominant or the non-dominant hand are analyzed in several steps following Tukey’s “detective work” approach. Correlation analyses (Person’s Product Moment) reveal skill-specific differences in individual grip force profiles across multiple sources of variation, functionally mapped to the somatosensory brain networks which ensure grip force control and its evolution with control expertise. Implications for the real-time monitoring of individual grip force profiles and their evolution with training in complex task-user systems are brought forward.

Background: This work presents Com@Rehab, a technological patient-centred activity for individuals needing a physical rehabilitation approach and with a specific loss of functionality. Within this scope, this paper focuses on the description of the activity in virtual reality (VR), its components, design and user profile, and its versatility and future adaptability regarding different ages, pathologies and rehabilitation contexts. Methods: The VR activity has been customised according to the patient's clinical needs while replicating an activity of daily living, namely showering. In addition, to validate and get feedback on the developed system, a validation questionnaire was applied to a group of healthy individuals to test the efficiency of the technology that supports the VR activity. Results: Preliminary results show that 94% of the participants recommended the experience, the performance of the various components of the system was successfully implemented, participants quickly adhered to the VR technology, and the UI assistant’s functionality should be improved. Conclusion: This solution creates a more effective, interactive, humanised rehabilitation approach based on a Virtual Reality (VR) activity. The Com@Rehab Communication Module improves human-human and human-machine communication while contributing to health literacy.

The article presents a method of generating Key Performance Indicators related to electric motor energy efficiency on the basis of Big Data gathered and processed in frequency converter. The authors proved that using the proposed solution it is possible to specify the relation between the control mode of an electric drive and the control quality-energy consumption ratio in the start-up phase as well as in the steady operation with various mechanical loads. The tests were carried out on a stand equipped with two electric motors (one driving, the other used to apply the load by adjusting the parameters of the built-in brake). The measurements were made in two load cases, for motor control modes available in industrially applied frequency converters (scalar V/f, vector Voltage Flux Control without encoder, vector Voltage Flux Control with encoder, vector Current Flux Control and Vector Current Flux Control with torque control). During the experiments values of current intensities (active and output), the actual frequency value, IxT utilization factor, relative torque and the current rotational speed were measured and processed. Based on the data the level of the energy efficiency was determined for various control modes.

Adaptation to external forces relies on a well-functioning proprioceptive system including muscle spindle afferents. Muscle length-tension control in reaction to external forces is most important regarding the Adaptive Force (AF). This study investigated the effect of different procedures, which are assumed to influence the function of muscle spindles, on the AF. 19 elbow flexors of 12 healthy participants were assessed by an objectified manual muscle test (MMT) with different procedures: regular MMT, MMT after pre-contraction (self-estimated 20% MVIC) in lengthened position with passive return to test position (CL) and MMT after CL with a second pre-contraction in test position (CL-CT). During regular MMTs, muscles maintained their length up to 99.7±1.0% of the maximal AF (AFmax). After CL, muscles started to lengthen at 53.0±22.5% of AFmax. For CL-CT, muscles were again able to maintain the isometric position up to 98.3±5.5% of AFmax. AFisomax differed highly significantly between CL vs. CL-CT and regular MMT. CL is assumed to generate a slack of muscle spindles which led to a substantial reduction of the holding capacity. This was immediately erased by a pre-contraction in test position. The results substantiate that muscle spindle sensitivity seems to play an important role for neuromuscular functioning and musculoskeletal stability.

Mirror Therapy (MT) and Cognitive Therapeutic Exercise (CTE) are two neurorehabilitation techniques based on neuroplasticity and designed to enhance the functionality of the upper limb. Therefore, the aim is to assess the effectiveness of the combination of CTE and MT with task-oriented training (TOT) on fine and gross motor skills of the affected hand, as well as the functionality of the affected upper limb, autonomy, independence, and quality of life (QoL) in patients with acute stroke. This longitudinal and multicenter study involved a sample of 120 participants selected randomly and consecutively. Three groups were formed, including a control group (CG) and two treatment groups, one with MT and the other with CTE. The functionality of the upper limb, fine and gross motor skills, the quantity and quality of use of the affected upper limb, autonomy, and QoL were evaluated using various scales validated in the Spanish population at the baseline, after 20 treatment sessions, and at three months of follow-up. ANCOVA analysis was conducted, revealing statistically significant differences between assessments in the CG compared to the experimental groups (GEs), indicating a notable improvement in overall functionality, fine and gross motor skills, autonomy, and QoL in the latter. However, there were no significant differences between the GEs. Therefore, the application of either of these experimental combinations is crucial for the motor recovery, functionality, and improvement of the quality of life of individuals who have suffered a stroke.

In the permanent magnet synchronous motor (PMSM) drive system, the unwilling and ear-piercing vibro-acoustics caused by high-frequency sideband harmonics becomes unacceptable in the electric vehicle application. In this paper, a modified space vector pulse-width modulation (SVPWM) technique implemented with hybrid carrier frequency modulation (HCFM) is provided to reduce the sideband current harmonic components and vibro-acoustic responses. The principle and implementation of the proposed HCFM technique are firstly presented, in which the fixed carrier frequency is improved with the sawtooth and random signal-based coupling modulation based on the rotor position. For verification, the experiment tests are carried out on a prototype 12/10 PMSM and microcontroller unit. The effectiveness of the HCFM technique can hence be confirmed, in which the sideband vibro-acoustics reduction shows more effectively than that in conventional random PWM. The proposed approach may provide a new route in noise-cancelling and electromagnetic compatibility for the electric drive powertrain.

In this research paper, a hybrid Artificial Neural Network (ANN)-Fuzzy Logic Control (FLC) tuned Flower Pollination Algorithm (FPA) as a Maximum Power Point Tracker (MPPT) is employed to emend root mean square error (RMSE) of photovoltaic (PV) modeling. Moreover, Gaussian membership functions have been considered for fuzzy controller design. This paper interprets Luo converter occupied brushless DC motor (BLDC) directed PV water pump application. Experimental responses certify the effectiveness of the suggested motor-pump system supporting diverse operating states. Luo converter is newly developed dc-dc converter has high power density, better voltage gain transfer and superior output waveform and able to track optimal power from PV modules. For BLDC speed controlling there is no extra circuitry and phase current sensors are enforced for this scheme. The recentness of this attempt is adaptive neuro-fuzzy inference system (ANFIS)-FPA operated BLDC directed PV pump with advanced Luo converter has not been formerly conferred.

This paper presents an Application Based Active Learning (ABAL) methodology on Power Electronics (PE) and Electric Machines (EM) as a hybrid laboratory course for the undergraduate students to design and implement the real-world engineering problems. The ABAL is a type of active learning which is a branch of Learner-centered teaching (LCT). The DC/DC converter along with the speed control of DC separately excites the motor. In addition, a DC/AC converter is designed to control the speed of an induction motor. The results are then investigated on a hardware platform under the ABAL experimental methodology. This paper also discusses the problem identification selection of the equipment, circuit design, hardware mounting and critical analysis of the results acquired from the hybrid laboratory. The ABAL methodology was evaluated based on student satisfaction, feedback, grades and interest to solve the real-world problem rather than cramming the engineering concepts and fulfill so-called lab routine and tasks

A modular approach to the construction of electric machines, drive systems, power supply systems is a new direction of modern technology development. Especially, the modular approach is promising for electric vehicles due to such positive aspects as increased efficiency, fault tolerance, overall reliability, safety, enhanced control capabilities, etc. In this work, the modular approach is comprehensively applied to an EV powertrain system, which includes a dual three-phase (DTP) BLDC motor with two machine modules of an asymmetric configuration, two battery modules and a supercapacitor module (SCM). The proposed H–H configuration of modular EV powertrain system includes four voltage source inverters that combine the power modules with the open ends of the windings (OEW) of the module machine armature, and provide control of their operation. Based on the developed mode system of the OEW machine module operation for EV traction and braking, a general control algorithm for the proposed configuration of the modular EV powertrain system has been developed. It combines the control of the operating modes with the functions of maintaining the required SOC level of the SCM and equalizing the SOCs of the two battery modules. The conducted simulation and experimental studies confirmed the workability and effectiveness of the proposed solutions.

Accurately predicting electrical signals of three-phase Direct Torque Control (DTC) induction motors is crucial for optimal motor performance and effective condition monitoring. However, multiple DTC motors’ complexity and operating conditions’ variations pose challenges for traditional prediction methods. To overcome these challenges, we propose an innovative approach that combines Fast Fourier Transform (FFT) to transform electrical motor simulation data and a Bi-directional Long Short-Term Memory (Bi-LSTM) network to forecast processed motor data. By transforming the DTC induction motor signals from the time domain to the frequency domain, we enhance the capability of learning models to capture subtle differences and generate various input features. The Bi-LSTM model effectively captures both forward and backward dependencies in time series data, enabling accurate prediction of electrical signals. We evaluate the proposed approach using our simulated dataset and compare the proposed method to a state-of-the-art model, the Gated Recurrent Unit (GRU), demonstrating its effectiveness in improving the accuracy and reliability of induction motor signals forecasting. The finding provides valuable insights for advancing motor control and operation in industrial applications.

Three different fields intersect in search of an understanding of the point-of-origin of modern-age diseases: 1) D-amino acids and their role under stress conditions; 2) evolutionary origin of the mitochondrion organelle in the eukaryotic cell; and 3) gut microbiota and human healthHere it is first suggested that D-amino acids function as universal signaling agents, after having evolved as prokaryotic communication, part of an organic communication process that governs the basic activities of all the cells and coordinates cell action.Mitochondria (symbiotic prokaryotic organelles), are creative source of D-amino acids as signaling agents in the central nervous system and in the neuroendocrine systems.Amino acids racemases catalyzes the conversion between the L-enantiomers ( protein building blocks) into D-enantiomers (signaling agents).It is suggested that hectic modern life may affect human health by causing stress to the gut microbiota. These affected, gut microbiota then secrete D-amino acids that enter the blood stream, as signaling agents, causing communication errors in the central nervous system, and in the neuroendocrine systems due to excessive quantity of D-amino acids.Treating gut microbiota with inhibitors of amino acids racemases or finding D-amino acid scavengers may be used in developing novel therapeutic strategies for diseases related to the central nervous system and neuroendocrine systems caused by stressed gut microbiota.

A novel metaheuristic optimization method is proposed based on an earthquake that is a geology phenomenon. The novel Earthquake Algorithm (EA) proposed, adapts the principle of propagation of geology waves P and S through the earth material composed by random density to ensure the dynamic balance between exploration and exploitation, in order to reach the best solution to optimization complex problems by searching for the optimum into the search space. The performance and validation of the EA are compared against the Bat Algorithm (BA) and the Particle Swarm Optimization (PSO) by using 10 diverse benchmark functions. In addition, an experimental engineering application is implemented to evaluate the proposed algorithm. Early results show a feasibility of the proposed method with a clearly constancy and stability. It is important highlight the fact that the main purpose of this paper is to present a new line of research, which is opened from the novel EA.

The extreme environmental issues and the resulting needs to save energy have turned the attention to electrification of energy applications. One of the key components involved in energy efficiency improvements is the appropriate conception and manufacturing of electric machines. This paper overviews the electromagnetic analysis governing the behavior of permanent magnets that enabled substantial efficiency gains in recent electric machine developments. Particular emphasis is given to model the properties and losses developed in permanent magnets in the emerging high speed applications. In addition, the investigation of properties and harmonic losses related to ferromagnetic materials constituting the machine magnetic circuits are equally analyzed and discussed. The experimental validation of the implemented methodologies and developed models with respect to the obtained precision is reported. The introduction of mixed numerical techniques based on the finite element method intended to appropriately represent the different physical phenomena encountered is outlined and discussed. Finally, fast and accurate simulation techniques including aggregated lumped parameter models considering harmonic losses associated with inverter supplies are commented.

Higher traffic density in Russian cities and less uniform traffic due to congestions are reasons for increased emissions of pollutants contained in exhaust gases of vehicles. The paper presents the modeling results of pollutant dispersion in Magnitogorsk. The analysis of these results shows that now many blocks of flats and social infrastructure of the city are in a zone with an excess of maximum allowable concentration of pollutants. Having summarized the methodological framework formulated by Russian and foreign researchers, the authors systemized the existing methods used to decrease pollutants produced by vehicles. It is proposed to choose an optimal combination of such methods applying a developed mathematical model. By adopting an optimal combination of the methods, it is possible to ensure minimum air pollutant emissions from vehicles, allocating limited financial resources. The mathematical modeling of the solutions on changing traffic density and structure and implementing methods used to decrease pollutants on one of the Magnitogorsk crossroads with the heaviest traffic is used to draw a conclusion about efficiency of the designed model used as a tool for strategic planning of development and transformation of street networks.

The Gilles de la Tourette syndrome (GTS) and Non-Coeliac Gluten Sensitivity (NCGS) may be associated. We analyse the efficacy of a gluten-free diet (GFD) in 29 patients with GTS (23 children; 6 adults) in a prospective pilot study. All of them followed a GFD for one year. The YGTSS, Y-BOCS/CY-BOCS and GTS-QOL questionnaires were compared before and after the GFD. 74% of children and 50% of adults were males, not significant (NS). At the beginning of the study, 69% of children and 100% of adults had associated OCD (NS). At baseline, the YGTSS scores were 55.0 ± 17.5 (children) and 55.8 ± 19.8 (adults) (NS), the Y-BOCS/CY-BOCS scores were 15.3 (SD = 12.3) (children) and 26.8 (9.2) (adults) (p = 0.043), and the GTS-QOL scores were 42.8 ± 18.5 (children) and 64 ± 7.9 (adults) (p = 0.000). NCGS was frequent in both groups, with headaches reported by 47.0% of children and 83.6% of adults (p = 0.001). After one year on a GFD there was a marked reduction in measures of tics (YGTSS) (p = 0.001), and the intensity and frequency of OCD (Y-BOCS/CY-BOCS) (p = 0.001), along with improved QOL (p = 0.001) in children and adults. In conclusion, a GFD maintained for one year in GTS patients led to a marked reduction in tics and OCD both in children and adults.

Syringomyelia can be associated with multiple etiologies. The treatment of the underlying causes is the first-line therapy, however, a direct approach to the syrinx is accepted as rescue treatment. Any direct intervention on the syrinx requires a myelotomy, posing a significant risk of iatrogenic spinal cord (SC) injury. Intraoperative neurophysiological monitoring (IONM) is crucial to detect and prevent surgically induced damage in neural SC pathways. We retrospectively reviewed the perioperative and intraoperative neurophysiological data and perioperative neurological examinations in ten cases of syringomyelia surgery. All monitored modalities remained stable throughout the surgery in six cases, correlating with no new postoperative neurological deficits. In two patients, significant transitory attenuation, or loss of motor evoked potentials (MEPs), were observed and recovered after a corrective surgical maneuver, with no new postoperative deficit. In two cases, a significant MEP decrement was noted, which lasted until the end of the surgery and was associated with postoperative weakness. A transitory train of neurotonic electromyography (EMG) discharges was reported in one case, the surgical plan was adjusted and the patient showed no postoperative deficit. The dorsal nerve roots were stimulated and identified in the seven cases where the myelotomy was performed via the dorsal root entry zone. Dorsal column mapping guided the myelotomy entry zone in four cases. In conclusion, multimodal IONM is feasible and reliable and may help prevent iatrogenic SC injury during syringomyelia surgery.