This research focuses on the computational design and analysis of various winglet Design types on a Boeing 737 aircraft. The idea is to compare the efficiencies of various winglet design types on a Boeing 737 aircraft half wing span and the picking out the best winglet design in respect to the pressure generated at the wing-tip and the lift-to-drag ratio of each winglet designs. The coefficient of lift-drag ratio in this research contribute to the reduction of fuel consumption

A fluid flowing over an object has a tendency to drag the object along it^’s flow direction. An object passing through a fluid which is stationary there is a tendency to slow the object down. For a stationary object in a fluid which is flowing there is a tendency to move the object in the fluid flowing direction .These tendencies of flowing fluid is known as drag. While moving through air airplanes also subjected to several drags. Airplanes subjected to pressure drag or form drag due to flow separation which is based on the pressure difference between the upstream and downstream surfaces of the object. Airplanes also subjected to Skin friction drag which results from the viscous shear of the fluid flowing over the object surface. In order to overcome these drags airplane wings cross section airfoils are designed very carefully. National Advisory Committee for Aeronautics, or NACA, developed and tested "families" of airfoils. Some of the most successful of these were the NACA four-digit and five-digit series. The necessary coordinates for designing NACA airfoil profiles are available in online. UIUC also provide coordinates for designing NACA airfoil profiles. But the present work describes the way of designing NACA four digit airfoils without taking any coordinates from available sources like google or any other search engines. Using C programming with the help of NACA provided equations a generalized source code is designed .Which will provide coordinates for designing any NACA four digit airfoil profiles .With the help of this obtained profile the wing model is also constructed using solid works. Using solid works model the real model was constructed using wood. The chord of regular surface airfoil is 21 cm and the span is also 21 cm. The airfoil profile taken for the model construction is NACA-4415 which is a four digit cambered airfoil.The present work also show some figures of an airfoil by applying certain surface modifications in form of dimples.

Traditional winglets are designed as fixed devices attached at the tips of the wings. The primary purpose of the winglets is to reduce the lift-induced drag, therefore improving aircraft performance and fuel efficiency. However, because winglets are fixed surfaces, they cannot be used to control lift-induced drag reductions or to obtain the largest lift-induced drag reductions at different flight conditions (take-off, climb, cruise, loitering, descent, approach, landing, and so on). In this work, we propose the use of variable cant angle winglets which could potentially allow aircraft to get the best all-around performance (in terms of lift-induced drag reduction), at different flight phases. By using computational fluid dynamics, we study the influence of the winglet cant angle and sweep angle on the performance of a benchmark wing at Mach numbers of 0.3 and 0.8395. The results obtained demonstrate that by adjusting the cant angle, the aerodynamic performance can be improved at different flight conditions.

The flow around thick airfoils at low Reynolds numbers and the possibility of using energy methods to control flowfield, increase lift and reduce drag are considered. For calculations, a series of propulsion airfoils is used, obtained by a combination of solving the inverse problem of aerodynamics and stochastic methods of global optimization. The calculations take into account the transition from the laminar flow regime to the turbulent one, which has a significant effect on the lift and airfoil drag. The applicability of various turbulence models for airfoil modelling at low Reynolds numbers is discussed. The results of numerical simulation make it possible to determine the dependence of the lift coefficient on the angle of attack and the optimal flow rate of air taken from the airfoil surface for each angle of attack. The results of numerical simulation are compared with the data of a physical experiment, and conclusions are drawn about the accuracy of various turbulence models.

Both drag and lift forces impact an inclined plane when it is dragged through a granular bed. In this paper, the following results have been obtained: the drag and lift forces grow with the velocity of motion; when the immersion depth is constant, the inclination angle has no effect on drag force, however, the lift force increases linearly with this inclination angle; the ratio of drag and lift forces is exactly equal to the tangent value of the inclined angle. In order to describe this physical process macroscopically, a continuum wedge model based on the Coulomb model is established to predict drag and lift forces. Particularly，the dynamic friction angle in the assumed shear band is predicted as a function of both inclined angle and moving velocity.

NACA 0015 and NACA 4415 aerofoil are most common four digits and broadly used aerodynamic shape. Both of the shapes are extensively used for various kind of applications including turbine blade, aircraft wing and so on. NACA 0015 is symmetrical and NACA 4415 is unsymmetrical in shape. Consequently, they have big one-of-a-kind in aerodynamic traits at the side of widespread differences of their utility and performance. Both of them undergo the same fluid principle while applied in any fluid medium giving dissimilar outcomes in aerodynamics behavior. On this work, experimental and numerical investigation of each NACA 0015 and NACA 4415 is done to decide their performance. For this purpose, aerofoil section is tested for a prevalence range attack of angle (AOA). The study addresses the performance of NACA 0015 and NACA 4415 and evaluates the dynamics of flow separation, lift, drag, pressure and velocity contour and so on. This additionally enables to layout new optimistic aerofoil, which is critical to enhance the efficiency and performance of an aircraft in terms of lift enhancement and drag reduction.

The application of numerical simulation methods for studying vertical-axis wind turbines offers significant advantages over conventional horizontal-axis wind turbines regarding wind energy utilisation, start-up wind speed, and environmental impact. This paper aims to investigate and establish the aerodynamic design performance of asymmetrical (NACA 4412) airfoils used in the application of vertical-axis wind turbines. The computational fluid dynamics (CFD) simulation uses Ansys software based on the Reynolds Averaged Navier-Stokes (RANS) equations. The aerodynamic parameters (pressure and velocity) are evaluated and compared within a range of angles of attack (AoA) 5-12 degrees at a fixed Reynolds number, as is a usual condition for wind turbine application. The lift coefficient (Cl), drag coefficient (Cd), and Cl/Cd ratio are obtained within the range AoA for the asymmetrical airfoils, and the performances have been predicted using the potential flow panel and CFD methods. This study suggests that while Xfoil may not be as precise as computational fluid dynamics (CFD), its predicted lift and drag coefficients generally align with experimental results. These help us to understand the best air-foil selection in a wind turbine application and predict its optimum AoA at which it performs at its best.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.

An increasing number of aircraft is equipped with wing tip devices, which either are installed by the aircraft manufacturer at the production line or are retrofitted after the delivery of the aircraft to its operator. Installation of wing tip devices has not been a popular choice for regional turboprop aircraft and the novelty of the current study is to investigate the feasibility of retrofitting the British Aerospace (BAe) Jetstream 31 with an appropriate wing tip device (or winglet) to increase its cruise range performance, taking also into account the aerodynamic and structural impact of the implementation. To the best of the knowledge of the authors, no previous study exists which has attempted to assess the winglet retrofit of an existing aircraft type of similar size and operating profile. The optimal winglet design achieved a 2.38% increase of the maximum range by reducing the total drag by 1.19% at a mass penalty of 3.25%, as compared with the baseline aircraft configuration. Other designs were found to be more effective in reducing the total drag, but the structural reinforcement required for their implementation outweighed the achieved performance improvements. Since successful winglet retrofit programs for typical short to medium range narrow body aircraft report even more than 3% of block fuel improvements, undertaking the project of installing an optimal winglet design to the BAe Jetstream 31, should also consider a Direct Operating Cost (DOC) assessment on top of the aerodynamic and structural aspects of the retrofit.

A number of experimental and numerical studies point out that incorporating a rotating cylinder can superiorly enhance the aerofoil performance, especially for higher velocity ratios. Yet, there have been less or no studies exploring the effects of lower velocity ratio at a higher Reynolds number. In the present study, we investigated the effects of Moving Surface Boundary-layer Control (MSBC) at lower velocity ratios (i.e. cylinder tangential velocity to free stream velocity) and higher Reynolds number on a symmetric aerofoil (e.g. NACA 0021) and an asymmetric aerofoil (e.g. NACA 23018). In particular, the aerodynamic performance with and without rotating cylinder at the leading edge of the NACA 0021 and NACA 23018 aerofoil was studied on the wind tunnel installed at Aerodynamics Laboratory. The aerofoil section was tested in the low subsonic wind tunnel, and the lift coefficient and the drag coefficient were studied for different angles of attack. The experiments were conducted for two Reynolds numbers: 200000 and 250000 corresponding to two free stream velocities: 20 m/s and 25 m/s, respectively, for six different angle of attacks (-5°, 0°, 5°, 10°, 15° and 20°). This study demonstrates that the incorporation of a leading edge rotating cylinder results in an increase of lift coefficient at lower angle of attacks (maximum around 33%) and delay in stall angle (from 10° to 15°) relative to the aerofoil without rotating cylinder.

This paper generalizes the actuator disc theory to the application of crosswind kite power systems. For simplicity, it is assumed that the kite sweeps an annulus in the air, perpendicular to the wind direction (i.e. straight downwind configuration with tether parallel to the wind). It is further assumed that the wind flow has a uniform distribution. Expressions for power harvested by the kite is obtained, where the effect of the kite on slowing down the wind (i.e. the induction factor) is taken into account. It is shown that although the induction factor may be small for a crosswind kite (of the order of a few percentage points), neglecting it in calculations may result in noticeable overestimation of the amount of power harvestable by a crosswind kite system.

: Inflammation may mediate the association of mitral valve prolapse (MVP) with ventricular scarring and arrhythmia. The purpose of this study is to investigate the association of neutrophil- and platelet-to-lymphocyte ratios (NLR, PLR) with ventricular arrhythmia in MVP. Clinical and demographic data were extracted from electronic medical records for all patients aged 18-90 years with MVP on echocardiography between 2016-19 at our institution. We studied 65 patients who had a differential blood count within six months prior to ambulatory ECG (A- ECG) (medi-an age [IQR] 70 [61-77] years; 62% female; 12% African American). Patients with surgery or in-fection within six months prior to CBC were excluded. Complex or frequent ventricular ectopy (cfVE) was defined as the presence of two or more premature ventricular contractions (PVCs) on a 10-second ECG tracing or greater than 1% PVC burden or NSVT on ambulatory ECG monitoring. Logistic and bivariate regression was used to analyze clinical, electrocardiographic and echo-cardiographic factors associated with NLR and PLR. Factors associated with higher NLR were congestive heart failure (p=0.005), male sex (p=0.01), age (p=0.003), and bileaflet MVP (p=0.04). NLR was associated with higher absolute PVC burden (rs=0.28, p=0.03) and cfVE (median NLR [IQR] 3.0 [1.6 – 6.3]) with cfVE versus (2.4 [1.4-3.4], p=0.04) without cfVE. An NLR of 5.6 yielded 50% sensitivity and 90% specificity for PVC burden >1% (AUC 0.69). No significant association was found between PLR and PVC burden or cfVE. NLR is associated with PVC burden and com-plex ventricular ectopy in MVP, suggesting that inflammation is a significant factor in the patho-genesis of ventricular arrhythmia in this condition.

In this study, we introduce a new type curve in 3-dimensional space which called B-lift curve and we obtain the Frenet operators of the B-lift curve. Moreover, we consider the correpondence of Frenet operators between the Blift curve and the natural lift curve. Finally, we investigate the B-lift curve according to the main curve is slant helix or darboux helix.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

Neutrophil to lymphocyte ratio (NLR) is a promising predictive and prognostic factor in breast cancer. We investigated its ability to predict disease-free survival (DFS) and overall survival (OS) in patients with luminal A or luminal B-HER2-negative breast cancer who received neoadjuvant chemotherapy (NACT). Pre-treatment complete blood cell counts from 168 consecutive patients with luminal breast cancer were evaluated to assess NLR. The study population was stratified into NLRlow or NLRhigh according to a cut-off value established by receiving operator curve (ROC) analysis. Data on additional pre- and post-treatment clinical-pathological characteristics were also collected. Kaplan-Meier curves, log-rank tests, and Cox proportional hazards models were used for statistical analyses. Patients with pre-treatment NLRlow showed a significantly shorter DFS (HR 6.97, 95% CI 1.65-10.55, p= 0.002) and OS (HR 7.79, 95% CI 1.25-15.07, p= 0.021) compared to those with NLRhigh. Non-ductal histology, luminal B subtype, and post-treatment Ki67≥ 14% were also associated with worse DFS (p= 0.016, p= 0.002, and p= 0.001, respectively). In multivariate analysis, luminal B subtype, post-treatment Ki67≥ 14%, and NLRlow remained independent prognostic factors for DFS, while only post-treatment Ki67≥ 14% and NLRlow affected OS. The present study provides evidence that pre-treatment NLRlow helps identify women at higher risk of recurrence and death among patients affected by luminal breast cancer treated with NACT.

Ustekinumab, a new anti-interleukin-12/23 antibody, is an effective treatment for ulcerative colitis; however, data regarding predictive factors of its efficacy are limited. This study aimed to identify biomarkers that can predict the long-term outcome of ustekinumab treatment. We retrospectively reviewed the records of patients with active ulcerative colitis treated with ustekinumab at our hospital from June 2020 to January 2023. We divided patients into non-remission and remission groups, and examined whether baseline biomarkers, including C-reactive protein-to-lymphocyte ratio, and early treatment response could predict clinical remission at week 48 of ustekinumab treatment. Of the 33 patients included in the study, 21 (63.6%) were in clinical remission at week 48 of ustekinumab treatment. The baseline C-reactive protein-to-lymphocyte ratio value was identified as an independent prognostic factor for clinical remission at week 48 (odds ratio: 10, 95% confidence interval: 1.6–62.4, p=0.014), with the cutoff value of 3.353 showing excellent prognostic performance (sensitivity: 71.4%, specificity: 83.3%). Furthermore, the clinical response at week 4 (p=0.009) and that at week 8 (p=0.005) were significantly associated with clinical remission at week 48. The baseline C-reactive protein-to-lymphocyte ratio value and early treatment response are useful biomarkers to predict the long-term efficacy of ustekinumab treatment.

The ratio of males to females with ASD is generally quoted as 4:1 though it is believed that there are biases preventing females being diagnosed and that the true ratio is lower. These biases have not been clearly identified or quantified. Starting with a clinical dataset of 1711 children <18 years old four different methods were employed in an inductive study to identify and quantify the biases and calculate the proportion of females missed. A mathematical model was constructed to compare the findings with current published data. The true male to female ratio appears to be 3:4. Eighty per cent of females remain undiagnosed at age 18 which has serious consequences for the mental health of young women.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

Type 2 diabetes mellitus may be complicated with chronic complications including diabetic neuropathy (DN). Timely diagnosis is crucial in treatment and maybe reversal of this complication. C reactive protein to albumin ratio (CAR) is considered as a marker of inflammation in various diseases that characterized with acute or chronic inflammation. Since diabetic neuropathy and type 2 diabetes mellitus are also associated with chronic, low grade inflammation, we aimed to study CAR levels of type 2 diabetic subjects with diabetic neuropathy and to compare to those in patients without diabetic neuropathy. Type 2 diabetic patients presented to our institutional outpatient clinics were divided into two according to the presence of DN. Subjects with DN were listed as DN group and others were as non-DN group. Characteristics and laboratory data, including CAR, in DN and non-DN groups were compared. Median CAR of the DN and non-DN groups were 2,19 (0,2-49)% and 0,56 (0,02-5,8)%, respectively (p&lt;0.001). CAR was significantly and positively correlated with age (r=0.15, p&lt;0.001), weight (r=0.19, p=0.01), BMI (r=0.11, p=0.03), waist circumference (r=0.10, p=0.046), fasting plasma glucose (r=0.14, p=0.004), serum creatinine (r=0.25, p&lt;0.001), triglyceride (r=0.17, p&lt;0.001), and LDL-cholesterol (r=0.13, p=0.001) levels. Moreover, CAR was inversely correlated with eGFR levels (r=-0.16, p&lt;0.001). The sensitivity and specificity of CAR (when higher than 1,02%) in predicting diabetic neuropathy were 78% and 73%, respectively (AUC: 0.84, p&lt;0.001, 95% CI: 0,82-0,87). Moreover, high CAR level was an independent risk factor of diabetic neuropathy (p&lt;0.001, OR: 1.34, 95% CI: 0.48-1.62). In conclusion, elevated CAR levels could be considered as a marker of diabetic neuropathy.

Drafting formations have been long recognized as highly effective for reducing drag and enhancing athletic performance, particularly in race walking events. The precise spacing and positioning of the race walkers are critical to optimizing the effectiveness of drafting. In this study, the drag reduction of 15 drafting formations is investigated using wind-tunnel experiments and CFD numerical simulations. The results show excellent consistency in drag reduction rate between the two methods, with differences being within 10%. This can be attributed to spacing replacing body shape differences as the primary factor influencing drag reduction. Optimal double, triple, and quadruple drafting formations produce the same results in both wind-tunnel experiments and CFD simulation, resulting in drag reductions of 67%, 66%, and 81% (wind-tunnel) and 65%, 72%, and 85% (CFD). The sources of drag differences in the two methods are discussed from various aspects. The flow field obtained through CFD analysis is used to examine the mechanism of drag reduction, revealing that drafting formations have a significant shielding effect on incoming air, which reduces the number and speed of airflow impacting the core race walker. This shielding effect is identified as the primary cause of drag reduction. Using an empirical model for mechanical power output, optimal double, triple, and quadruple drafting formations enhance sport economy (4.4-5.7%), speed (3.61-4.67%), and performance (173.8-223.3s) compared to race walking alone. The findings can serve as a reference for race walkers' positioning strategy and provide insights for considering drafting formations in various running events.

Backgroundː Previous studies have shown that both serum creatinine and D-dimer levels were associated with atherosclerotic coronary artery disease (CAD). We aimed to determine whether DCR is associated with coronary Gensini score in patients with ST-elevation myocardial infarction (STEMI). Methodsː 337 STEMI patients with complete D-dimer and creatinine and other necessary information were included in the analysis. According to the values of the DCR, patients were divided into the lower DCR group (DCR ≤ 1.42, n = 173) and the higher DCR group (DFR > 1.42, n = 174), and the differences between the two groups were compared. Multivariate linear and multivariate logistic regression analyses were performed to determine independent predictors of Gensini score. Resultsː High DCR group had higher Gensini score compared with low DCR group (P < 0.05). DCR was positively correlated with Gensini score (r=0.493, P < 0.001). Multiple linear regression analysis showed that Previous MI (r=11.312, P=0.035) and DCR (r=5.129, P<0.001) were independent risk factors associated with Gensini score. Multivariate logistic regression analysis showed that, compared to the group 1, DCR is independent risk factor for Group 2, Group 3, Group 4 (P <0.001). DCR is positively correlated with coronary Gensini score in STEMI patients and can be used as an independent predictor of higher Gensini score. Conclusionsː As a new and useful clinical marker, DCR is positively correlated with coronary Gensini score in STEMI patients and can be used as an independent predictor of higher Gensini score.

Abstract: Systemic inflammatory response syndrome (SIRS) is a clinical diagnosis based on abnormalities in patients' vital signs and white blood cell count. Neutrophil-lymphocyte ratio (NLR) is used as an easily accessible parameter to assess the patient's inflammatory status and stress. There are some studies showing that NLR affected by the inflammatory response is a criterion to support the diagnosis of SIRS. In this study, it was aimed to compare the interrelation between SIRS (+) and SIRS (-) groups in patients with high positive feline coronavirus (FCoV) in the light of NLR. Based on the anamneses, physical examination findings, laboratory findings, enzyme immunoassay antibody test kit titer were included in the sick groups. These patients were further categorized based on the presence of SIRS symptoms, vital signs and laboratory findings. The NLR as diagnostic marker demonstrated to differ between high antibody titer FCoV positive and healthy cats. However the diagnostic significance of NLR remains questionable between the high antibody titer FCoV positive cats with SIRS (+) and SIRS (-). As a result of our study NLR can be used as a blood parameter like albumin/globulin ratio and elevated total bilirubin in cats with high FCoV antibody titer and high probability of developing FIP.

Drafting is a common technique to reduce the drag experienced by elite runners on races, leading to better running efficiency and energy savings. The tactic has been successfully used in previous races where world records were set, especially by Eliud Kipchoge in the 2018 and 2022 editions of the Berlin marathon. In the 2023 edition of the Chicago Marathon, Kenyan runner Kelvin Kiptum broke the Marathon record after a 2:00:35 finish. This feat becomes even more impressive by the lack of use of drafting formations, despite the availability of two pacers for the majority of the race. In this study, the drag faced by Kiptum and his pacers during the race is calculated by means of computational fluid dynamics (CFD). The performance of each runner is evaluated from an energetic standpoint, and the analysis is extended to include more efficient drafting formations. Our results indicate that, by properly using the advantages of drafting, Kiptum could have finished the race at a staggering 1:57:34, a full three minutes better than his own record and 215 seconds better than the previous world record.

Background: Feline infectious peritonitis (FIP) is a fatal feline disease classified as either effusive (‘wet’), non-effusive (‘dry’), or a mixture of both forms (‘mixed’). The anti-FIP therapeutic effect of Mutian and molnupiravir, two drugs whose active ingredient is a nucleic acid analog, has been confirmed recently. Methods: Of the cats with FIP, we observed a total of 122 and 56 cases achieved remission after administration of Mutian and molnupiravir as routine treatments, respectively. Changes in clinical indicators suggested to be correlated with FIP remission (weight, hematocrit, and albumin to globulin ratio) before and after the administration of each drug and during follow-up observation were statistically compared for each FIP type. Results: In all three FIP types, administration of either Mutian or molnupiravir resulted in statistically significant increases in these indicators. Furthermore, the effect of Mutian on improving the albumin to globulin ratio was not observed at all in wet FIP, as compared with that of molnupiravir, but statistically significant in mixed and dry (P<0.02 and P<0.003, respectively). These clinical features were all due to differences in fluctuations of circulating globulin levels. Conclusions: These results indicate slight inflammatory responses might be elicited continuously by residual feline coronavirus non-disappeared through molnupiravir treatments.

Vibrational overtones in deeply bound molecules are sensitive probes for variation of the proton-to-electron mass ratio μ. In nonpolar molecules, these overtones may be driven as two-photon transitions. Here, we present procedures for experiments with O₂⁺, including state-preparation through photoionization, a two-photon probe, and detection. We calculate transition dipole moments between all X²П_g vibrational levels and those of the A²П_u excited electronic state. Using these dipole moments, we calculate two-photon transition rates and AC-Stark-shift systematics for the overtones. We estimate other systematic effects and statistical precision. Two-photon vibrational transitions in O₂⁺ provide multiple routes to improved searches for μ variation.

The Review examines studies aimed at the organization of energy (non-mechanical) control of high-speed flow/flight using spatially multi-component plasma structures and combined energy deposition. The Review covers selected works on experimental obtaining and numerical modeling multi-component plasma structures and use of sets of actuators based on the plasma of such a spatially type for the purposes of control of shock wave/bow shock wave – energy source interaction, as well as control of shock wave – boundary layer interaction. A series of works on repetitive multiple laser pulse plasma structures is also analyzed from the point of view of examining shock wave/bow shock wave boundary layer interaction. Self-sustained theoretical models for laser dual-pulse, multi-mode laser pulses and self-sustained glow discharge are also considered. Separate sections are devoted to high-speed flow control using combined physical phenomena and numerical prediction of flow control possibilities using thermal longitudinally layered plasma structures. The wide possibilities for organization and applying spatially multi-component structured plasma for the purposes of high-speed flow control are demonstrated.

Catamaran hulls have always been associated with smaller vessels in naval engineering and construction. However, recent research results have shown that by considering specific criteria based on materiality, structure and functionality, they can be designed for a more complex industry, such as hydrofoil design. Among the challenges in this type of vessel, one of the most difficult variables is estimating the resistance to the advance in the function of the degree of uncertainty generated. This research focuses on optimising the drag of a sport sailing catamaran by implementing hydrofoils, through the application of computational fluid dynamics (CFD), at different speeds to demonstrate that it is possible to modify and improve the current appendages of this vessel.

Changes in the amount and the distribution of mean and turbulent quantities in the free shear layer wake of a 2D NACA 0012 airfoil and AR 4 NACA 0012 wing with passive segmented rigid trailing edge (TE) extensions was investigated at the University of Dayton Low Speed Wind Tunnel (UD-LSWT). The TE extensions were intentionally placed at zero degrees with respect to the chord line to study the effects of segmented extensions without changing the effective angle of attack. Force based experiments was used to determine the total lift coefficient variation of hte wing with seven segmented trailing edge extensions distributed across the span. The segmented trailing edge extensions had negligible effect of lift coefficient but showed measurable decrement in sectional and total drag coefficient. Investigation of turbulent quantities (obtained through Particle Image Velocimetry (PIV)) such as Reynolds stress, streamwise and transverse RMS in the wake, reveal a significant decrease in magnitude when compared to the baseline. The decrease in the magnitude of turbulent parameters was supported by the changes in coherent structures obtained through two-point correlations. Apart from the reduction in drag, the lower turbulent wake generated by the extensions has implications in reducing structural vibrations and acoustic tones.

Obesity is a troubling public health problem worldwide as it increases risks of respiratory complications, systemic arterial hypertension, type 2 diabetes mellitus, sleep disorders, cardiovascular diseases, and metabolic syndrome (MetS). As a measure to counteract comorbidities associated with severe obesity, bariatric surgery stands out. This study aimed to investigate the adiponectin/leptin ratio in women with severe obesity with and without MetS undergone Roux-en-Y Gastric Bypass (RYGB) and to characterize the biochemical, glucose, and inflammatory parameters of blood in women with severe obesity before and after RYGB. Were enrolled female with severe obesity undergoing RYGP with MetS (n=11) and without (n=39). Anthropometric data and blood samples were obtained before and 6 months after RYGB to analyze total cholesterol, low-density lipoprotein (LDL), high- density lipoprotein (HDL), non-HDL total cholesterol, and glucose; and circulating levels of adiponectin and leptin. Significant reductions in weight, body mass index, and glucose, total cholesterol, LDL, and leptin were observed after surgery, with higher levels of HDL, adiponectin, and adiponectin/leptin ratio observed after surgery compared to preoperative values. This study demonstrated that weight loss induced by RYGB in patients with severe obesity with or without MetS improved biochemical and systemic inflammatory parameters, particularly the adiponectin/leptin ratio.

In this study, the friction factor of turbulent pipe flow for dried rice malt extract solutions is reduced experimentally to that of a Newtonian fluid. The friction factor is measured for four types of solutions at different culture times and concentrations. The results indicate that the experimental data points of the test solutions diverge from the maximum drag reduction asymptote at and above Re√f ≅ 200 and align parallel to those of Newtonian fluids. This drag reduction phenomenon differs from that of artificial high molecular polymer solutions. It is classified as a Type B drag reduction phenomenon of biopolymer solutions and fine solid particle suspensions. The order of drag reduction corresponds approximately to that of 5–50 ppm xanthan-gum solutions reported previously. Furthermore, the velocity profile in a turbulent pipe flow was predicted using a semi-theoretical equation, in which the friction factors were determined using the difference between the experimental results of the tested solutions and Newtonian fluids. The results indicate a more considerable thickening of the viscous sublayer in the turbulent pipe flow of the test solutions than that of Newtonian fluids.

Polymeric drag reducers have been developed over many years due to the great number of practical applications. In all of them, the molecular stability is an essential requirement. Usually, polymers break down under turbulent flows, which causes a decrease in their efficiency as drag reducers. Besides that, some specific applications, in agro and biomedical fields, impose a specific requirement that must be fulfilled, which is the use of non-toxic materials. A suitable stable material that is elected to accomplish this necessity is the mucilage of aloe vera, which is a bio-polymer that can be used as an alternative to the synthetic ones. Here, we investigate the role played by the aging of aloe vera on its capacity to reduce drag. The results obtained by ¹H nuclear magnetic resonance indicate that the compositions of young and mature leaves of aloe vera are different and such a difference plays an important role on their efficiency as drag reducers. Tests were performed to analyse the drag reduction in a rotating apparatus and in a pipeline system and the efficiencies of leaves of different ages were compared to their composition. The main conclusion of these experiments is that the young mucilage samples, which are richer in complex polysaccharides and exhibit lower acid contents, are more efficient drag reducers.

An explanation of aerodynamic lift still is under controversial discussion as can be seen, for example, in a recent published article in Scientific American [1]. In contrast to an approach via integral conservation laws we here review an approach via the classical Kutta-Condition and its relation to boundary layer theory. Thereby we summarize known results for viscous correction to the lift coefficient for thin aerodynamic profiles and try to remember the work on triple-deck or higher order Boundary Layer theory, its connection to interactive boundary layer theory, viscous/inviscid coupling as implemented to well-known engineering code Xfoil. Finally we compare its findings to simple 2D numerical solution of full Navier Stokes equations (CFD)models. As a conclusion, a clearer definition of terms like understanding and explanation applied to the phenomenon of aerodynamic lift will be given.

We all have in mind Einstein's famous thought experiment in the elevator where we observe the free fall of a body and then the trajectory of a light ray. Simply here, in addition to the qualitative aspect, we carry out the exact calculation. We consider a uniformly accelerated reference frame in rectilinear translation and we show that the trajectories of the particles are ellipses centered on the horizon of the events. The frame of reference is non-inertial, the space-time is flat, the metric is non-Minkowskian and the computations are performed within the framework of special relativity. Some experimental consequences are discussed such as trajectory deviation, desynchronization of a falling clock and the Michelson interferometer. The differences, compared to the classical case, are important at large scale and close to the horizon, but they are small in the box where the interest is above all theoretical and pedagogical. The study helps the student to become familiar with the concepts of metric, coordinate velocity, horizon, and, to do the analogy with the black hole.

Ditching-rotary tiller was widely used in tillage and ditching furrow during rapeseed sowing. As its ditching furrow system (consist of four identical ditching plows) would bear great drag resistance from the soil during operation, the ditching plow was optimized based on differential geometry analysis and EDEM simulation. Resistance-velocity simulation indicated the plow with parabolic type guide curve had better reduce-drag characteristics. Differential geometry analysis indicated decay rate of E and growth rate of G could represent the variable regularity of drag resistance with the increase of velocity. The L value could represent the magnitude of drag resistance. The smaller L value, decay rate of E and growth rate of G, the better drag-reduce characteristics. Quadratic rotation orthogonal combination design shown the optimal structural parameter values were: Δθ=15°, θmin=45°, h=250mm, l=100mm. The minimum average drag resistance was 230.1N. The differential geometry analysis of optimal ditching plow shown |dE/dκ| and |dG/dκ| could obtain minimum value, indicating growth rate of drag resistance for optimal plow was the lowest within the experimental level. Field experiment indicated the operation effect of optimized ditching furrow system could met the requirements of rapeseed sowing. The research provided in-depth theoretical guidance for Drag-reduce design of plow.

The study of a flexible body immersed in a flowing medium is one of best way to find its aerodynamic shape. This Letter revisited the problem first studied by Alben, Shelley and Zhang (Nature 420, 479-481, 2002). The aerodynamic shape of the fibre is found by simpler approach and universal drag scaling laws of the flexible fibre in flowing medium are proposed by using dimensional analysis. The Alben scaling laws is being generalized and confirmed to be universal. Our study show that the Alben number is a measurement of maximum curvature of the fibre forced by dynamic pressure. A complete Maple code is provided for finding aerodynamic shape of the fibre in the flowing medium.

Abstract: The pursuit of youth and attractiveness is a fundamental desire in contemporary society. For many individuals, the appearance of visible signs of aging, such as skin laxity, gravitational changes in facial and neck soft tissues, and loss of harmonious proportions, can be psychologically distressing. The choice of effective methods for addressing these changes depends on their specific characteristics, the patient's anatomical features, and the type of facial aging. The introduction of 3D imaging to determine the hyoid bone level, the volume of soft tissue structures in the cervico-mental area, ptosis of subplatysmal structures, and the volume of submandibular glands, in addition to ultrasound study of the submental projection at the preoperative stage, are key for taking the best decision regarding preoperative planning. This case report aims to illustrate how modern imaging techniques are a fundamental part of the preoperative assessment of the mid and lower third of the face to ensure the most favorable aesthetic outcomes for each patient. Key message: To attain harmonious results in surgical correction of age-related facial and neck changes, it is crucial to consider the patient's anatomical features and the extent of age-related alterations. A comprehensive facial analysis, taking into account the type of facial aging and employing a CT scan and ultrasound examination of the soft tissues in the chin region, facilitates the development of an individualized plan tailored to achieve the patient's desired outcome.

Abstract A variety of surgical techniques have been developed to reconstruct the posterior maxilla when bone volume is insufficient. A barrier membrane or bone window pushed inside the sinus cavity as the ‘‘roof’’ of the sinus cavity for preserve the space and help bone. The heterologous cortical lamina is used for the mechanical support, without any grafting material, of sinus membranes resulting in only bone tissue formation and not mixed with the graft.

The automotive industry has witnessed a significant push towards increased fuel efficiency and reduced carbon emissions. Among many factors influencing overall vehicle efficiency, aerodynamic drag is a critical consideration, accounting for a substantial portion of fuel consumption. Our investigation focused on the drag coefficients of three prominent 2023 passenger car models – the Toyota Corolla, Hyundai Elantra, and Kia Soul. Using ANSYS Fluent to perform computational fluid dynamics, we demonstrated an inverse correlation between drag force and gas mileage, underlining the significance of aerodynamic design in fuel efficiency. Notably, the Hyundai Elantra emerged as the most aerodynamically efficient of the three vehicles, followed closely by the Toyota Corolla. In contrast, the boxier-designed Kia Soul exhibited significantly higher drag coefficients and drag forces, rendering it the least efficient of the trio. These findings emphasize the importance of environmental factors in car design. Shaping aerodynamic profiles directly impacts fuel efficiency, stability, and overall performance.

The emergence of electric vehicles has brought new issues such as the problem of rolling element bearings (REBs) operating at high speeds. Losses due to these components in mechanical transmissions are a key issue and must therefore be taken into account right from the design stage of these systems. Among these losses, the one induced by the motion of rolling elements , known as drag loss, becomes predominant in high-speed REBs. Although an experimental approach is still possible, it is difficult to isolate this loss in order to study it properly. A numerical approach based on CFD is therefore a possible way forward, even if other issues arise. The aim of this article is to study the ability of such an approach to correctly estimate the drag coefficient associated with the motion of rolling elements. The influence of the numerical domain extension, the mesh refinement, the simplification of the ring shape and the presence of the cage, on the values of the drag coefficient is presented. While it seems possible to compromise on the calculation domain and mesh size, it appears that the other parameters must be taken into account as much as possible to obtain realistic results.

This article presents a study on the aerodynamic drag of a generic dual-axle flatbed trailer and explores ways to reduce the drag using appendable drag-reducing devices. The primary sources of drag originated from the van and trailer’s rear, along with the trailer’s wheels. The most effective initial device for reducing drag was a full trailer underside cover which offered a 7% drag reduction. Additionally, ladder racks, dropsides, and rear gates were studied, and it was found that protruding ladder racks significantly increased drag. Rear gates added large amounts of drag and should be removed and stored when not needed. The study also explored novel mid-section devices that increased the van’s base pressure and reduced drag. An axle test revealed that drag for single, dual, and triple axle trailers was very similar in direct flow, but different in yawed flow. A drawbar length test showed a near-linear relationship between drawbar length and drag, manifesting as a 1.7% change in drag per 250mm change in drawbar length. Several novel modifications were made to the trailer, including fitting six unique appendable devices, which offered a total 7.3% drag reduction. A novel rear van device known as the Multi-Stage Converging Cavity was introduced which reduced drag by nearly 18%. When all the devices were used together, a total 25% drag reduction was observed for the van-trailer combination.

The influence of small-scale processes at the ocean-atmosphere boundary layer such as spray and foam on the surface waves prediction is studied. Estimates of the effect of including the exact number of specific fragmentation "parachute" type in the spray on the resulting drag coefficient is shown. For the estimates, the numerical simulations within WAVEWATCH III wave model are performed. The parameterizations of wind input were tested within WAVEWATCH III wave model: default ST4 and ST6 parameterizations and the ST1 and ST6 parameterizations used together with the implemented drag coefficient parameterization. The proposed parameterization takes into account the presence of foam and spay. The obtained results are compared with the NDBC buoys data. The importance of small-scale processes for waves at hurricane winds prediction and the prospects for their inclusion in modern numerical wave models is shown.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

This comprehensive study focused on the standard taxi sign used in Ireland, its impact on drag production, fuel expenses, and CO2 emissions. Experimental analysis revealed that the conventional taxi sign significantly increased drag, especially when mounted on streamlined vehicles such as saloon cars, due to flow separation issues on the rear roof and rear windshield. Longitudinal reorientation of the sign offered a 14-fold reduction in drag increase compared to the traditional placement. It was found that positioning the sign in the middle of the roof offered the greatest fuel efficiency. Furthermore, the study estimated that implementing longitudinal repositioning on all Irish taxi signs could save drivers approximately 832 per year and reduce national CO2 emissions by a substantial 22,464 tonnes annually. Comparative analyses with international taxi signs demonstrated that the Irish sign had significantly larger drag contributions, emphasizing the need for improved aerodynamics. To address the inherent drag issue, the study explored novel appendable devices and proposed alternative taxi sign designs. Among the tested solutions, a magnet-mounted front ramp proved the most effective, reducing total drag by nearly 30%. Additionally, a motorized flip-up taxi sign design demonstrated a remarkable 40% reduction in drag. Finally, a newly proposed taxi sign design, featuring longitudinal positioning and pointed triangular front and rear faces, resulted in a minimal 4.3% increase in vehicle drag compared to the baseline car.

Drag-dominant tidal turbine energy holds tremendous clean energy potential but faces significant hurdles as unsuitability of Disk Actuator theory due to the varying swept blockage area, unaccounted bypass flow downstream interaction and rotor parasitic drag whereas Blade Element Momentum theory is computably effective for majorly 3-blade lift-dominated aerofoil. This study proposes a novel method to find the optimal TSR of any turbine with a cost-effective and user-friendly Moment Balancing algorithm to support robust tidal energy development. Performance analysis CFD study of Pinwheel and Savonius tidal turbines was carried out. Dynamic TSR matrix was developed with varying rotational speeds and fluid velocities for reliability, unlike previous works simulated at a fixed fluid velocity. Novel parameters such as thrust and idle moment are introduced as functions of only inlet fluid velocity and rotational speed respectively. These relationships are verified through regression analysis, and the turbines' net moment equations are established based on these parameters. Rotational speed was a reliable predictor for Pinwheel's idle moment, while inlet velocity was a reliable predictor for thrust moment in both models. The optimal (Cp, TSR) values for Pinwheel and Savonius turbines were (2.37, 0.223) and (0.63, 0.16) respectively, within an acceptable error range for experimental validation.

This paper presents an investigation into the influence of drag-reducing polymer (DRP) on the flow of water inside and around U-bends. The DRPs tested were partially hydrolysed polyacrylamide (HPAM) and two different molecular weight polyethylene oxides (PEO). The Reynolds number and in-situ concentration ranges of water and DRP were and respectively. The test section was made up of clear polyvinyl chloride (CPVC) pipes that contained two U-bends with radii of curvature (R) of 100 and 200 mm as well as straight sections of 19-mm ID. Higher pressure gradient was recorded in the under-developed flow section after the bend. Drag reduction (DR) increased with in-situ concentration of the DRP and the flowrate up to some threshold values. The concentration and flowrate thresholds were about 20 ppm and 1.07 m/s respectively. DR differed among the different sections considered with the highest values recorded for developed flows upstream of the bend and the least values recorded in the bend. DR at station 1 (immediately after the bend) was generally lower than that at station 2 (further downstream). P-K Plots showed that, the DR envelop for developed flow in straight pipes did not apply to the bend and the under-developed flow section. DR increased with polymer molecular weight and ionic strength in straight sections. However, molecular weight (and polymer shearing) had limited effect on DR in the bends. DR characteristics at the bend suggested that there was a different or additional mechanism. The effect of bend curvature ratio on DR was predominant after the U-bend. The larger the ratio of pipe diameter to bend diameter, the lower the DR in the redeveloping sections after the bend. For R = 100 mm, the highest DR recorded for fully developed flows before bend, in the bend, at stations 1 and 2 were 57, 31, 36 and 33% respectively while that for R = 200 mm were 64, 28, 42 and 49% respectively.

Electromagnetic sensing has been used for diverse applications of non-destructive testing, including the surface inspection, measurement of properties, object characterization. However, the measurement accuracy could be significantly influenced by the lift-off between sensors and samples. To address the issue caused by lift-offs, various strategies have been proposed for the permeability measurement of ferromagnetic steels, which mainly involves different sensor designs and signal features (e.g., the zero-crossing feature). In this paper, a single high-frequency scenario for the permeability retrieval is introduced. By combining the signal of two sensing pairs, the retrieval of magnetic permeability is less affected by the lift-off of sensors. Unlike the previous strategy on reducing the lift-off effect (directly taking the phase term out of the integration) using the Dodd-Deeds analytical method, the proposed method is based on a high-frequency linear feature of the phase term. Therefore, this method has the merit of high accuracy and fast processing for the permeability retrieval (a simplified version of Dodd-Deeds analytical formulas after the integration). Experimental measurement has been carried out on the impedance measurement of designed sensors interrogating ferromagnetic dual-phase steels. For sensor lift-offs of up to 10 mm, the error of the permeability retrieval is controlled within 4 % under the optimal frequency.

Eddy current sensors can be used to test the characteristics and measure the parameters of the conductive samples. As the main obstacle of the multi-frequency eddy current sensor, the lift-off distance affects the effectiveness and accuracy of the measurement. In this paper, a material-independent algorithm has been proposed for the restoration of the lift-off distance when using the multi-frequency eddy current sensor, which is based on the approximation under the thin-skin effect. Experiment testing on the performance of the proposed method is presented. Results show that from the dual-frequency inductance, the lift-off distance could be restored with a maximum error of 0.24 mm for the distance up to 12 mm. Besides, the derived lift-off distance is used for the inversion of the magnetic permeability. Based on a lift-off insensitive inductance (LII) feature, the magnetic permeability of steels can be inversed in an iterative manner, with an error of less than 0.6 % for the lift-off distance up to 12 mm.

Purpose: The aim of the present experimental 3D-finite element study was to evaluate the influence of an augmented sinus lift with an additional inserted bone graft block. The bone graft block stabilizes the implant in addition to conventional augmented bone. We placed the block in three different positions. The implants were loaded with axial force and forces secondary to laterotrusion and protrusion. Material and Methods: A simplified U-shaped 3D finite element model of the upper jaw and a more complex anatomical model of the left maxilla were created. The bone graft block was placed in three positions: in the lower third in contact with the sinus floor, the middle, and the upper third of the implant. Van Mises’ stress distribution was calculated and analyzed for the different models. We also compared the complex anatomical model with the simplified one. Results: The position of the bone graft block significantly influences the magnitude of stress distribution. A bone graft block positioned in the upper third or middle of the implant reduces the quantity of stress compared to the reference model without a bone graft block. The low bone graft block position is clearly associated with lower stress distribution in compact bone. We registered no significant differences in stress in compact bone with regard to laterotrusion or protrusion. Conclusions: Maximum values of von Mises stresses in compact bone can be reduced significantly by using a bone graft block. The reduction of stress is nearly the same for positions in the upper third and the middle of the implant. It is much more pronounced when the bone graft block is in the lower third of the implant near the sinus floor, which appeared to be the best position in the present study.

Light travels in a moving medium through densities that differ from the density of that medium at rest. This study derives a formula for light velocity through a moving medium for any direction of light propagation in that medium that, applied to the Fizeau experiment, gives a fringe shift of 0.23541. The Fresnel drag coefficient applied to the Fizeau experiment offers a fringe shift of 0.20466. The mean of the fringe shift observations in the Fizeau experiment of 0.23016 confirms both expectations.

The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.

Optimal operation of petroleum production is important in a transition from energy systems based on fossil fuel to sustainable systems. One sub-process in petroleum production deals with transport from the (subsea) well-bore to a topside separator. A simple model in [] of Electric Submersible Pump [ESP] lifted production was previously streamlined into a dynamic model suitable for illustration of the dynamics of oil transport, as well for control studies, with some comparison of two popular modeling languages: Modelica, and ModelingToolkit for Julia, []. Here, the discussion on dimensionless equipment models goes into more detail, and the comparison between Modelica and ModelingToolkit is significantly expanded upon with code comparison, numerical performance, and more experiments. Some added possibilities with ModelingToolkit and Julia wrt. sensitivity analysis and control design is included.

The common dandelion uses a bundle of drag-enhancing bristles (the pappus) that enables seed dispersal over formidable distances; however, the scaling laws of aerodynamic drag underpinning pappus-mediated flight remains unresolved. In this paper, we study the aerodynamic shape of dandelion, derive the scaling law of resistance, determine the Vogel exponent. In particular, we find that the total drag coefficient is proportional to the -2/3 power of the dandelion pappus Reynolds number, and obtain the terminal velocity of the dandelion seed under gravitation field.

Eddy current testing can be used to interrogate steels but it is hampered by the lift-off distance of the sensor. Previously, the lift-off point of intersection (LOI) feature has been found for the pulsed eddy current (PEC) testing. In this paper, a lift-off invariant inductance (LII) feature is proposed for the multi-frequency eddy current (MEC) testing, which merely targets the ferromagnetic steels. That is, at a certain working frequency, the measured inductance signal is found nearly immune to the lift-off distance of the sensor. Such working frequency and inductance are termed as the lift-off invariant frequency (LIF) and LII. Through simulations and experimental measurements of different steels under the multi-frequency manner, the LII has been verified to be merely related to the sensor parameters and independent of different steels. By referring to the LIF of the test piece and using an iterative inverse solver, one of the steel properties (either the electrical conductivity or magnetic permeability) can be reconstructed with a high accuracy.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

For the electromagnetic eddy current testing, various methods have been proposed for reducing the lift-off error on the measurement of samples. In this paper, instead of eliminating the measurement error caused by the lift-off effect, an algorithm has been proposed to directly measure the lift-off distance between the sensor and non-magnetic conductive plates. The algorithm is based on a sample-independent inductance (SII) feature. That is, under high working frequencies, the inductance is found sensitive to the lift-off distance and independent of the test piece under an optimal single high working frequency (43.87 kHz). Furthermore, the predicted lift-off distance is used for the thickness prediction of the non-magnetic conductive samples using an iterative method. Considering the eddy current skin depth, the thickness prediction is operated under a single lower frequency (0.20 kHz). As the inductance has different sensitivities to the lift-off and thickness, the prediction error of the sample thickness is different from that of the lift-off distance. From the experiments on three different nonmagnetic samples – aluminium, copper, and brass, the maximum prediction error of the lift-off distance and sample thickness is 1.1 mm and 5.42 % respectively at the lift-off of 12.0 mm.

Previously, various techniques have been proposed for reducing the lift-off effect on the thickness measurement of the non-magnetic films, including the peak-frequency feature and phase feature in the Dodd-Deed analytical formulation. To realise a real-time feedback response on the thickness monitoring, the phase term in the Dodd-Deeds formulation must be taken off the integration. Previous methods were based on the slow change rate of the phase term when compared to the rest of the term – the magnitude term. However, the change rate of the phase term is still considerable for a range of working frequencies. In this paper, a high-frequency feature has been found. That is, the ratio between the imaginary and real part of the phase term is proportional to the integral variable under high frequencies. Based on this proportion relationship, the phase term has been taken out; and a thickness algorithm has been proposed. By combing the measured impedance from the custom-built sensor (three coils), the thickness of the metallic film can be reconstructed. Experiments have been carried out for the verification of the proposed scenario. Results show that the thickness of the metal film can be reconstructed with a small error of less than 2 %, and immune to a reasonable range of lift-offs.

Rather high speed of modern water bikes that they develop using only human muscle power increases their popularity. For example, the maximum speed of prototypes reaches the value 3 m/s. Similar vehicles can be used not only for recreation and fitness, but also for transportation. To increase their speed and tonnage, we recommend improving the pontoon shape and using electrical power. The total drag and maximal speeds of the vehicles with the human muscle and electrical power are estimated. Expected success in improving the pontoon shape opens wide prospects for the use of these special shaped hulls in shipbuilding.

Large Language Models (LLMs) have proved significant proficiency when comes to code generation especially in Structured Query Language (SQL) for databases and recent successful Text-to-SQL method involves fine-tuning pre-trained LLMs for SQL generation tasks. Transforming natural language text into SQL queries, has been attempted to solve with various learning techniques including Few-shot learning[1], fine tuning. In this paper we propose Supervised fine-tuning (SFT) as a better alternative for learning technique for text-to-SQL generation task using Code-Llama that pushes state of art accuracy on spider test suite to 89.6% on dev set which represent first instance of surpassing the earlier best-in-class with 5.5% higher score and 86.8% of exact match accuracy on dev set. Furthermore, we demonstrate that properly prompted LLM along with SFT provides far fewer hallucinations and much more robust LLM that can be used as a general tool for any text-to-SQL generation use case.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

The research examines the relationship between self-rated health situation and personal percep-tion of heat waves, and how social linkage of communities would be a moderator variable in residents’ perception of heat waves in Taiwan. This study uses the questionnaire conducted by Sinica “Responsive Capacity under Heat Wave: The Perspectives of the Locals”(2019), using OLS method for estimating the unknown parameters in multiple regression model. The author finds that the correlation of self-rated health situation and perception toward heat is significantly posi-tive. Also, social linkage in communities affects strongly as a moderator variable: While the sat-isfaction to with their community could reduce negative reaction to heat, contacts with neighbors could increase possibility people feel uncomfortable in high-temperature situation. This study ex-hibits the effects of social environment on community, and expects further related researches or practices to strengthen capability to resist heat wavesƒ for Taiwanese residents.

Amebiasis is a disease caused by the unicellular parasite Entamoeba histolytica. In most cases, the infection is asymptomatic but when symptomatic, the infection can cause dysentery and invasive extraintestinal complications. In the gut, E.histolytica feeds on bacteria. Increasing evidences support the role of the gut microbiota in the development of the disease. In this review we will discuss the consequences of E.histolytica infection on the gut microbiota. We will also discuss new evidences about the role of the gut microbiota in regulating the resistance of the parasite to oxi-dative stress and its virulence.

Objective: To explore three novel fasting blood glucose (FBG)-based novel indicators, including FBG-to-albumin ratio (FAR), FBG-to-lymphocytes ratio (FLR), and FBG-to-hemoglobin ratio (FHR), in predicting prognosis and detecting metastasis for patients with pancreatic neuroendocrine neoplasms after resection. Materials and methods: A total of 178 pNEN patients underwent surgical resection were included in this study. Receiver operating characteristic (ROC) curves were used to evaluate the diagnosis values of FAR, FLR, and FHR, and the cut-off values were obtained for further analyses. Univariate and multivariate analyses were conducted to determine the independent predictors. The Kaplan-Meier method was used to evaluate the progression-free survival (PFS) and overall survival (OS) of the pNEN patients. Results: The optimal cut-off values of FAR, FLR, and FHR were 0.17, 2.85, and 0.028, respectively. As for PFS, the area under the curve (AUC) was 0.693 for FAR, 0.690 for FLR, and 0.661 for FHR, respectively. The AUC was 0.770, 0.692, and 0.715 accordingly for OS. The groups with lower FAR, FLR, and FHR were significantly associated with prolonged PFS and OS (p < 0.05). In patients with metastasis, the lower FAR group was correlated with significantly longer PFS and OS (p = 0.022 and 0.002, respectively). The FLR was an independent predictor of PFS in pNEN patients, and the FAR was a predictor of OS. FAR was an independent indicator of PFS in patients with metastasis. Conclusion: Preoperative FAR, FLR, and FHR are effective in predicting the prognosis of pNEN patients and detecting the synchronous metastases.

Objective: The current study aimed to delineate the relationship of furin with inflammation while cervical intraepithelial neoplasia progresses to cancer. Study Design:This cross-sectional study included 81 women who required colposcopic examinations. The study groups were formed based on pathological results: Group I included women with cervical intraepithelial neoplasia (CIN) I (n=30); Group II included women with CIN II-III (n=28); and Group III included women with cervical cancer (CC) (n=23). Furin, ki-67, and p16 levels were evaluated based on immunostaining intensity. The inflammatory indices were calculated parallel with the literature from routine blood samples retrieved within one week before the procedure. Results:Furin expression gradually increased from CIN I to CIN II-III and from CIN II-III to CC, respectively (p < .001, p = .005). The NLR, MLR, PLR, and SII were significantly higher in the CC group (p < .001). ROC curve analysis unveiled that NLR, MLR, PLR and SII predicted the presence of CC with a cutoff value of 2.39 for NLR (sensitivity: 91.3%, specificity: 63.8%, AUROC: 0.79, p < .001); a cutoff value of 0.27 for MLR (sensitivity: 78.3%, specificity: 72.4%, AUROC: 0.77, p = .009); a cutoff value of 123 for PLR (sensitivity: 100%, specificity: 41.4%, AUROC: 0.70, p = .04); and a cutoff value of 747 for SII (sensitivity: 69.6%, specificity: 90.7%, AUROC: 0.71, p = .014). Conclusion:Furin expression increased gradually in parallel to the severity of cervical intraepithelial neoplasia. The inflammatory indices were higher in the presence of CC and denoted good discrimination ability for predicting cervical cancer.

Mass plays a strange multiple role in classical physics. This results in a difference between gravity and all other forces - a difference that stood at the beginning of Einstein's development of his general theory of relativity. The equivalence principle (EP) deals with homogenious gravitational fields, which, in fact, don‘t exist in nature. There is only an approximation for this field in Einstein-Lift possible for local situations. Nevertheless this EP can be true, because in classical formal binary logic there can be formulated a true conclusion from a wrong premise or assumption.

Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

Previously, a conductivity invariance phenomena (CIP) has been discovered – at a certain lift-off, the inductance change of the sensor due to a test sample is immune to conductivity variations, i.e. the inductance – lift-off curve passes through a common point at a certain lift-off, termed as conductivity invariance lift-off. However, this conductivity invariance lift-off is fixed for a particular sensor setup, which is not convenient for various sample conditions. In this paper, we propose using two parameters in the coil design – the horizontal and vertical distances between the transmitter and the receiver to control the conductivity invariance lift-off. The relationship between these two parameters and the conductivity invariance lift-off is investigated by simulation and experiments and it has been found that there is an approximate linear relationship between these two parameters and the conductivity invariance lift-off. This is useful for applications where the measurements have restrictions on lift-off, e.g. uneven coating thickness which limits the range of the lift-off of probe during the measurements. Therefore, based on this relationship, it can be easier to adjust the configuration of the probe for a better inspection of the test samples.

(1) Background: Little research has been done on professionals' perceptions of institutions and governments during epidemics. We aim to create a profile of physicians who feel they can raise public health issues with relevant institutions during a pandemic. (2) Methods: A total of 1285 Romanian physicians completed an online survey as part of a larger study. We used binary logistic regression to profile physicians who felt able to raise public health issues with relevant institutions; (3) Results: Five predictors could differentiate between respondents who tended to agree with the trust statement and those who tended to disagree: feeling safe at work during the pandemic, considering the financial incentive worth the risk, receiving training on the use of protective equipment, having the same values as colleagues, and enjoying work as much as before the pandemic; (4) Conclusions: Physicians who trust the system to raise public health issues with the appropriate institutions feel they share the same values as their colleagues, say they were trained in the use of protective equipment used during the pandemic, felt they were safe at work during the pandemic, enjoyed their work as much as before the pandemic, and felt the financial bonus justified the risk.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

Economic development and population growth lead to increased production of chicken manure (CM), which is a problematic organic waste for its amount, environmental threats, and moisture content. There are different ways of CM, namely anaerobic digestion, composting, combustion, and direct land spreading. Hydrothermal carbonization (HTC) is another emerging way, however. In this study, the HTC of CM was performed to produce energy-rich material called hydrochar (HC). The effects of HTC temperature (180, 240, 300 C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as heating values (HHV, LHV), have been performed both on raw CM and derived HC. Additionally, the process performance has been examined. The obtained results show that HTC is a feasible method for CM disposal and valorization. Although process time did not influence considerably fuel properties of CM, higher temperature led to significantly higher HHV, reaching 23,880.6734.56 Jg-1 at 300 C and 180 min with an improvement of 8,329 Jg-1 compared with raw CM (15,551.67 Jg-1). The process conducted at 240 C in 30 min has been specified as the most favorable, due to the highest energy gain of HC and relatively low energy consumption.

The increase in the emission of greenhouse gases (GHG) is one of the most important world problems. Decreasing of GHG emission is a big challenge in the future. Transportation sector uses a significant part of petroleum production in the world and it leads to an increase in the emission of GHG. The result of this issue is that population of the world befoul environment of transportation system automatically. Electric Vehicles (EV) have a potentiality to solve a big part of the GHG emission and energy efficiency issues such as stability and reality of energy. The energy actors and their research team determine some targets for 2050; hence, they hope to decrease the world temperature to 6 °C in the best and 2 °C in the normal condition. Fulfillment of these scenarios needs suitable grid infrastructure but in most of the countries, the grid does not have a suitable background to apply those scenarios. In this paper, some problems about energy scenarios, energy storage systems, grid infrastructure and communication systems in supply and demand side of the grid and its solutions have been investigated.

Vehicle to vehicle (V2V) and Vehicle to infrastructure (V2I) or briefly V2X communications are the one of hot topics in automotive industry. Therefore, this situation is providing many advantages of connected vehicles and infrastructures which bring to human life. For instance, vehicles and road infrastructures which shares information with each other, provides a neat flow regulation, more ordered traffic flow and therefore jammed traffic dependent accident’s percentage will be decreased. On the other hand, security is the most important issue for these systems because the operation of V2X networks is completely dependent on uninterrupted and accurate information sharing. In the light of these information, in this paper we review security issues and current solution architectures. We also propose some open problems in this lively field.

Sustaining learners’ motivation to keep learning has been concerned for over 60 years in education and SLA. Most research focusing on Japanese university students has contributed lots of theoretical and practical developments, but research focusing on motivations of non-traditional adult learners and those under 18-year-old to learn Chinese is still little even though previous research findings have proved age is one of the key variables influencing learning besides nationalities and Chinese language levels. In order to find an effective treatment for sustainable Chinese language learning in Japan, this study utilized a survey method to analyze the types of Japanese learners’ motivation to learn Chinese via analysis of a moment structures (AMOS), and to compare the differences of the motivation via one-way ANOVA. This study revealed that Japanese learners’ motivation to learn Chinese consists of eight common types, which are “instrumental motivation”, “personal orientation”, “identified regulation”, “Chinese cultural productions”, “integrating into Chinese community”, “external regulation”, “social responsibility”, and “Chinese for academic purposes”. Also, there are similarities and differences existing in the eight motivation types among the Japanese children, adolescents, (non-) traditional adult learners of Chinese as a foreign language (CFL). The findings contribute the understanding of motivation types and differences among the four aged Japanese learners to teachers of teaching Chinese to speakers of other languages (TCSOL), and to future research further exploring how differently aged Japanese learners can have and use a higher motivation as a main drive to learn Chinese language as a lifelong business.

The research is devoted to the problem of noise generation during flights of supersonic civil aircrafts. The effect of a thermally stratified energy source used to control the flow past a pointed cylinder aerodynamic models on the nearfield and ground pressure signatures, as well as on the perceived loudness in decibels (PLdB) on the ground is evaluated. The fields of parameters and the dynamics of the drag forces are studied for different values of temperature in the layers of the thermally stratified energy source and for different number of layers in it. It has been shown that when performing the flow control at freestream Mach numbers 1.5-2 using thermally stratified energy sources with the number of layers from 2.5 to 7.5 and rarefaction parameters in the layers from 0.15 to 0.3, no additional noise impact on the ground is introduced. Thus, the simulations showed that changing the surface pressure signature due to drag reduction does not necessarily imply a change in the PLdB on the ground.

A community-level nutrition intervention was implemented among tribal children (3 to 6 years) in Telangana, India. The one-year intervention involved six nutrient-rich formulations of millet-pulse-groundnut based products, suited to local taste preferences. Anthropometric measurements of height, weight and Mid-Upper-Arm -Circumference (MUAC) along with haemoglobin (Hb) levels were monitored at baseline and endline. The treatment group showed considerable gain in height (3.2 cm), weight (1.68 kg) and MUAC (0.33 cm), over the control group. Paired t-test indicated significant differences (p<.01) between pre- and post-intervention anthropometric measurements. Positive shifts were observed in wasting (WHZ; -1.2 ±1.3 to -0.9± 1), stunting (HAZ; -1.8±1.6 to -0.3±1.3) and underweight (WAZ; -1.9±1.2 to -0.7±1) among treatment group. Hb levels in the treatment group also improved significantly from 9.70 ± 0.14 g/dl (moderately-anaemic) to 11.08 ± 0.13 g/dl (non-anaemic). Post-intervention Focus Group Discussions (FGDs) involving mothers and teachers confirmed the positive impact. Thus, nutritional intervention formulated using climate resilient millets, pulses and groundnut, promotes dietary diversity and improves the nutrition & health status of children.

This research endeavors to illuminate the path toward efficient and optimized propeller design by delving into the realm of aerodynamics. Propellers, as vital mechanical marvels, constitute the core of numerous propulsion systems, spanning from aircraft and marine vessels to wind turbines. The pursuit of enhanced propeller efficiency and performance holds paramount importance in industries where propulsion assumes a critical role, underscoring the indispensable need for a profound understanding of aerodynamics. Through meticulously crafted theoretical insights and their practical applications, this study embarks on a journey into the fascinating realm of propeller aerodynamics. While the paper primarily addresses the aerodynamic aspects of propeller design and optimization, it serves as a foundational guide for those seeking to comprehend the intricacies of propeller engineering.The research journey commences with an in-depth exploration of the fundamental principles governing propeller performance. It unveils the intricate dynamics of airflow surrounding propeller blades, shedding light on their proficiency in generating thrust, lift, and torque. The bedrock of the theoretical insights is a comprehensive analysis encompassing airfoil profiles, blade geometry, and the underlying principles of blade element theory. In navigating the ensuing pages, the study embarks on the task of demystifying the intricate methods and calculations that propel the design and optimization of propellers. Leveraging cutting-edge methodologies, the research systematically assesses the aerodynamic characteristics of propellers across various operational conditions. These invaluable insights empower the tailoring of propeller designs with precision, aligning them seamlessly with specific performance objectives. The aim is not only to impart a comprehensive understanding of propeller aerodynamics but also to provide actionable insights for engineers and researchers striving to enhance propeller efficiency. This research endeavor serves as a guiding light for both propeller enthusiasts and professionals alike. It not only enriches the broader discourse on propeller technology but also equips readers with the requisite knowledge and tools to embark on their own quests for optimized propeller design. As propulsion technologies continue their evolution, the steadfast principles elucidated herein will persist, guiding future innovations and advancements in the realm of propeller engineering. This paper serves as a profound resource, offering new researchers a comprehensive understanding of propellers and their intricate design processes.

Access to medicines is one of the essential problems in Public Health of low- and middle-income countries (LMICs). The World Health Organization (WHO) defines access to medicines as the possibility of "having continuously accessible and affordable medicines in public or private health facilities that are within a kilometer of the place of residence." Access to medicines, as defined by the WHO, is not fully guaranteed in many LMICs and even in many regions of high-resource countries. The WHO identifies several factors as determinants of limitations in the access to medicines: rational selection, affordable prices, sustainable financing, and reliable health services. The action on these factors makes it possible to improve universal access to medicines with consequent improvement in Public Health. Adequate access to antibiotics and vaccination will avoid a large part of the deaths caused by infectious diseases in the LMICs. However, the emergence of resistance and the difficulties in vaccination campaigns due to socio-political or cultural problems make it challenging to fight many easily treatable infectious diseases. The use and abuse of antibiotics are inevitably associated with the appearance of resistances that make them ineffective. Thus, whereas limited access to antibiotics raises mortality rates from infectious diseases, generalized open access to them ends up eliminating their clinical value. Moreover, the contraction of research in this field for many years has reduced the success in discovering new drugs. Additionally, local market regulations, inadequate selection, inaccessible prices, especially for those of second and third-generation, inefficient health systems, and difficulties of administration and control of prescription compliance, especially in the case of combined therapies, are additional obstacles to universal access to antibiotics. In order to simultaneously improve access to antibiotics and keep resistances under control, it is necessary to develop training and education activities at different social levels (from patients to various Health Care Providers) to complement the national or supranational strategic plans.

Neuropsychiatric manifestations of COVID-19 include delirium, general malaise, headache, and psychiatric symptoms. These manifestations are related to the neuroinflammatory response to viral antigens and proinflammatory mediators/immune cells. Tetracyclines, such as minocycline, have antibacterial and anti-inflammatory properties. Saiko-keishi-to, a traditional Japanese Kampo medicine, also has anti-inflammatory properties. Given the anti-inflammatory properties of minocycline and Saiko-keishi-to, we describe two cases of COVID-19 with prolonged headaches and general malaise successfully treated with these medications.

This study aims to describe the commitment to national heritage, patriotism, nationalism of elementary school students in the border areas between Indonesia and Timor Leste. This research was conducted in three elementary schools, they are SD Inpres Moto Ain, SD Inpres Class Jau Halimuti, SD Kristen Nanaeklot, and SD Negeri Motabenar from June to August 2018. The subjects of this study were elementary students in the Indonesia-Timor Leste border areas precisely around Motaain City, Belu Regency, East Nusa Tenggara. The research questionnaire was adapted from Karazawa and analyzed with descripriptive statistics. The results of this study showed that the commitment to national heritage, patriotism, and nationalism of elementary students on the Indonesian border areas with Timor Leste is in the very high level.

Aim: To investigate inflammation indices and erythropoietin (EPO) levels for their potential role in distinguishing polycythemia vera (PV) from secondary polycythemia (SP), and to compare different parameter combinations in terms of diagnostic accuracy. Methods: This retrospective cohort was created from patients assessed for polycythemia from January 2020 to December 2023. PV diagnosis was made according to the 2016 WHO criteria (n=145). Those who did not fulfill the criteria were defined as having SP (n=84). Results: NLR, PLR and SII were significantly higher in the PV group (p

Background. IgA nephropathy (IgAN) is associated with chronic inflammation. Platelet-related parameters, such as platelet (PLT) count, platelet-to-albumin ratio (PAR) and platelet-to-lymphocyte ratio (PLR), were examined as potential prognostic indicators for renal and cardiovascular (CV) outcomes in IgAN. Methods. 150 IgAN patients were devided into two groups based on the cut-off value of PAR. All-cause mortality, major CV events and end-stage renal disease were the primary combined endpoints. Secondary endpoints, such as CV or renal endpoints, were also analyzed separately. Results. The patient’s mean age was 43.7 ± 13.5 years, and the follow-up time was 124 ± 67 months. The K-M curve showed that PLR, PAR and PLT were strongly associated with primary combined (p = 0.002, p = 0.004, p = 0.001) and renal outcomes (p < 0.001, p < 0.001, p < 0.001), but not with CV outcomes in IgAN. However, when combined with left ventricular hypertrophy (LVH) or metabolic syndrome (MetS) PAR was found to be a significant predictor of both primary (p < 0.001, p < 0.001) and secondary outcomes (p = 0.001 and p = 0.038; p = 0.001 and p = 0.015). Additionally, PLR correlated with microalbuminuria (r = -0.165, p = 0.033) and LVH (r = -0.178, p = 0.025), while PLT correlated with eGFR (r = 0.158, p = 0.040). Conclusion. Elevated PAR and PLR may predict progression to end-stage kidney disease, but in combination with LVH and MetS, they showed CV events also in IgAN. The determination of PAR and PLR can be useful and cost-effective parameters for assessing both cardiovascular and renal risks in CKD.

Background: The aim of this study has been to investigate if inflammatory biomarkers such as the systemic immune-inflammation index (SII), neutrophil to lymphocyte ratio (NLR) and platelet to lymphocyte ratio (PLR) have any correlation with the recurrence of pleomorphic adenomas (PA) in patients afflicted by this disease. Methods: A retrospective multicentre study involving two Italian centres, the Maxillofacial Sur-gery at the Policlinico Federico II in Naples and the ENT and Maxillofacial Surgery at the IRCCS G. Pascale National Cancer Institute in Naples, has been performed. The study, involving 608 pa-tients who had received a diagnosis of PA, was conducted between January 2000 and January 2020. A Receiver Operating Characteristic (ROC) curve was used to calculate the optimal cut-off values for the SII, PLR and NLR. A linear regression model (LRM) and a non-linear logistic re-gression model (NLRM) were realized with respect to the NLR, PLR and SII. Results: The highest performance was achieved by the NLR (cut-off 2.960) with the AUC = 0.91, with an accuracy of 96.1%, sensitivity of 78.4% and specificity of 97.2%, PPV = 64.4% and NPV = 98.6%. The LRM and NLRM including all the haematological parameters did not increase the per-formance in terms of recurrence detection. Conclusion: The NLR is an excellent support tool in predicting the recurrence of PA with a cut-off of 2.960. It can be a good reference point for surgical decision-making and follow-up in clinical practice.

The paper introduces and describes the recent and still ongoing development activities performed in Luxembourg for In-Orbit Attach Mechanisms for (Drag) Sails Modules to be operated from Space Tugs. After some preparatory work aiming at understanding the possible operational aspects, three designs have been completed for their 3D (Metal and Plastic) Printing. The Plastic-printed prototype underwent a series of automated tests where a robotic arm, equipped with an advanced force sensor, replicated four docking scenarii in ideal and degraded modes. The observation of the forces and torques behaviors at and after impact allowed to characterize the typical patterns for the various contacts but also, to identify a type of impact potentially dramatic for the safety of the docking and its equipment: in case of off-axis approach, “point” contacts shall be avoided as they instantaneously transfer the total kinetic energy in a small area that could break.

Breast cancer (BC) affects millions of women; it is the leading cause of death by neoplasia in wom-en worldwide, with at least 500 thousand deaths each year, 70% of which occur in developing countries. Elastography evaluates tissue stiffness, making this a promising non-invasive real-time technique. BI-RADS is recognized as a standard and helpful technique for establishing BC risk. This study aimed to determine, by strain elastography (SE), the fat-to-lesion index (F/L index), sen-sitivity, specificity, and optimal cut-off to diagnose BC. This prospective study included 216 wom-en who underwent SE, ultrasound, mammography, and breast biopsy; according to mammogra-phy, we recruited BI-RADS category 2 (n= 5), category 3 (n=29), category 4 (n= 94), category 5 (n= 71) and category 6 (n=17); after biopsy, 108 women were classified as negative, and 108 were pos-itive for BC. Three expert BC radiologists performed all imaging interpretations and biopsies. Our results show mean values of the F/L index for negative biopsies of 3.70±2.57 and positive biopsies of 18.10±17.01; we developed two models for the prediction of BC, a logistic regression model with an AUC of 0.893 and a neural network with an AUC of 0.902. The Youden index yielded a F/L index cut-off >5.76, with a sensitivity and specificity of 84.26%. Positive Spearman's Rho cor-relation coefficient was observed between the F/L index and BI-RADS, r=.073 (p< 0.001). ANOVA test showed a difference between F/L index vs. molecular subtypes (p=0.002). SE is helpful as a di-agnostic complement to mammography, or in cases where the latter is contraindicated, elas-tography has an adequate predictive capacity and is a fast and minimally invasive procedure.

It has been proposed that upregulation of the noradrenergic (NA) system through exposure to novelty might be one of the key components for building cognitive reserve and resilience to neurodegeneration. A personality trait that promotes greater interest in novel experiences is Openness to Experience (OE). Individuals who are high in OE exhibit strong curiosity towards novelty and are more likely to be exposed to novel stimuli throughout the lifespan.Performing voxel-based morphometry analyses, we examined whether OE in 135 healthy young adults was associated with Locus Coeruleus (LC) - the main core of the noradrenergic system. We also investigated whether LC mediates the relationship between OE and a key measure of reserve, I.Q. In comparison with other neuromodulators’ seeds (Dorsal and Median Raphe [DR-MR] -5-HT, Ventral Tegmental Area [VTA] -DA- and Nucleus Basalis of Meynert [NBM] -Ach-), results show that greater LC integrity was related to greater OE and IQ. Additionally, mediation analyses revealed that only LC mediated the relationship between OE and IQ. Furthermore, a Bayesian multiple regression was conducted to model the contribution of both isolated and combined neuromodulator seeds to OE trait express. This approach found that the LC + VTA could account for more variance in OE expression compared to the LC alone. Other weaker but significant associations were observed between DR and OE, between LC + NBM and Conscientiousness and between DR + NBM and Extraversion. These results are together suggestive that OE is primarily underpinned by monoaminergic functioning, and that the LC-NA system plays a central role mediating the interdependence between OE expression and cognition (IQ level). While offering further understanding of the neurobiology of human personality, these findings indicate a pivotal role of LC-NA system integrity in novelty seeking in daily life. This provides a psychobiological account for how OE expression may be beneficial for maintaining the noradrenergic system to facilitate cognitive reserve and resilience to neurodegenerative conditions.

This paper compares the performance of three text-to-speech (TTS) models released from June 2021 to January 2022 in order to establish a baseline for Brazilian Portuguese. Those models were trained using dataset for Brazilian Portuguese. The experimental setup considers tts-portuguese dataset to fine-tune the following TTS models: VITS end-to-end model; glowtts and gradtts acoustic models both using hifi-gan vocoder. Performance metrics are arranged into objective and subjective metrics. As subjective metrics, the naturalness and intelligibility are measured based on the mean opinion score (MOS). Results shows that gradtts+hifigan model achieved naturalness of 4.07 MOS, close to performance of current commercial models.

Background: Vaccinating children against COVID-19 is an essential public health strategy in order to reach herd immunity and prevent illness among children and adults. Parents are facing tremendous stress in relation to the COVID-19 pandemic and the effectiveness of the COVID-19 vaccination program for children. In this study, we aimed to investigate parents’ willingness to vaccinate their children against COVID-19 in North Kivu province (DRC). Methods: A cross-sectional survey between December 01, 2021 to January 20, 2022 in 6 health zones (Goma, Karisimbi, Butembo, Beni, Kamango and Katwa) was conducted in the province of North Kivu. In each health zone, we selected 5 clusters (Health area) using the method of probabilistic selection proportional to population size. In total, 522 parents participated in our study. Results: Overall, 32.8% of parents intended to vaccinate their children. In the multivariate analysis, younger age of parents (aOR : 2.40, CI : [1.50-3.83]), higher level of fear that “a member of my family” could contract COVID-19 (aOR : 2.35, CI : [1.38-4.02]), higher level of perceived vulnerability to COVID-19 within the family (aOR : 1.70, CI : [1.005-2.2881]), higher level of perceived susceptibility to COVID-19 within the family (aOR : 3.07, CI : [1.80-5.23]), and history of vaccination against COVID-19 among parents (aOR : 16.47, CI : [8.39-32.33]), were significantly associated with the intention to have their children or adolescents vaccinated. Conclusion: Willingness of parents to vaccinate their children against the COVID-19 vaccination was low in North Kivu. There is undeniably in this region a need to reinsure the populations about vaccine safety for both children and adults. Public health authorities should also address widespread misinformation about vaccines in a timely manner.

With the COVID-19 pandemic continuing and the resulting economic burden increasingly apparent, the Indonesian government began to prepare a "new normal" phase and make peace with COVID-19. From this new decision arises the question of the readiness of businesses and the industrial sector to resume operations amid COVID-19. This article aims to provide concise and precise information about the preparations that can be made by businesses to operate safely amid COVID-19 based on existing scientific studies and literatures. From the literature visits it can be concluded that transmission and danger of a COVID-19 pandemic can be prevented through: creation of infectious disease prevention and response plan, implementing basic infection prevention measures, policies and procedures for proper identification and isolation of sick people, applying flexibilities in policies, and protections in the workplace.

Here we review and describe a set of research priorities to meet present and future challenges posed to farmed animal production that build on progress, successes and resources from the Functional Annotation of ANimal Genomes (FAANG) project.

South America has become the new epicenter of the coronavirus, especially in Brazil where the disease continues to spread exponentially across the country. This text aims to analyze the psychosocial factors of Covid-19 on back to school strategies in Brazil from a bioecological perspective. At the microsystem level, the population is experiencing different levels of stress and fear; at the mesosystem level, changes in routines, separation from family and friends, and closure of schools; and at the macrosystem level, national guidelines to control the pandemic, institutional standards on a national and international scale. Therefore, the main focus for the success of school return must be in the prevention of contagion and with physical and psychological health, and should not only consider the demands of curricula, financial or administrative management. For this reason, it is paramount that greater female representativeness is increased in decision-making levels of the meso and macrosystem, regarding the resumption of school and academic activities in the pandemic period, since the number of female leaders in decision-making, is still insufficient.

The COVID-19 pandemic has presented the world with increased challenges. The response to this pandemic has led to a sudden disruption of routine medical and elective surgical care. Most hospitals across the globe have had to change the way outpatient clinics are carried out and postpone non-urgent elective surgical procedures. NHS England ceased all elective general surgeries to train and re-deploy their staff to support the increased pressures from COVID-19 in an intensive care setting. However, with a decline of reported cases and deaths, the return to undertaking non-urgent elective services is imminent. In May 2020, Radha and Afzal published the first evidence-based guidelines for the resumption of elective orthopaedic services titled “Evidence based suggestions for the return to elective orthopaedic surgery following the COVID-19 Pandemic”. The pathway presented is adapted from the “Evidence based suggestions for the return to elective orthopaedic surgery following the COVID-19 Pandemic” and could potentially be used as a model for other surgical specialities. We present a three-phased return back to urological services. Safe resumption of elective care is possible but needs to be carefully planned.

Most large fibers in central nervous system of vertebrates are decussated. The cause or the evolutionary force of this phenomenon is not convincingly described. Here we show a pattern for this nervous system property that simultaneously is found to a more basic rule in evolution.The idea here is the "function to anatomy" theorem. We claim that functions of physical, biochemical, enzymatic, etc., in lower scale of living organisms "emerge" to anatomy in larger scales. And reversely, the anatomy we see in multicelular organisms are/were functions in microscopic scales.We propose descriptions, predictions, and a probable road map to what this can implicate in biological and medical issues.

In 2014, the outbreak of adenoviral pneumonia occurred in Korean military training center. However, there is limited data on characteristics of fever and its response to antipyretics therapy in immunocompetent adults with adenoviral positive community-acquired pneumonia (CAP). Medical records of patients who were admitted to Armed Forces Chuncheon Hospital for treatment of CAP between January 2014 and December 2016 were retrospectively analyzed. We evaluated demographics, clinico-laboratory findings and radiologic findings at admission were compared between adenovirus positive (Adv) group and adenovirus negative (non-Adv) group. Out of 251 military personnel with CAP during the study periods, 67 were classified into Adv group while 184 were Non-Adv group. Patients with Adv group had a longer duration of fever after admission and symptom onset. Adv group patients had a higher mean temperature at admission and more observed over 40 and 39 to 40℃. Adv group patients had more commonly observed no response to antipyretic treatment and adverse events after antipyretics use. Length of hospital stay had no significant difference between two groups and no patient died in both groups. In our study, Adv positive CAP in patients with immunocompetent military personnel had distinct characteristics of fever and response to antipyretic treatment.

An understanding of the cultural conditions that determine the factors affecting nurses’ intention to leave is important for countries suffering from nurse shortage. Aim: to examine factors influencing intention to leave among female hospital nurses in a large Japanese sample, classified into four generations by age considering economic conditions. Methods: a cross-sectional survey with convenience sampling was conducted. Anonymous self-administered questionnaires were distributed to all nurses in 30 hospitals. To assess intention to leave, basic attributes, life conditions, work characteristics, and factors of psychosocial work environment were addressed. After classifying data into four generations based on age cohorts, we conducted multivariate logistic regression analysis using the completed data (N = 5,074, mean age = 36.24). Results: regardless of generational characteristics influenced by economic conditions, effort and monetary reward were generation-common factors. Over-commitment, social support, and the presence of a role model were generation-common factors in three generations. While having children increased intention to leave in the generation born 1965–1979, having family members in need of caregiving other than children decreased the risk in the generation born in the 1980s. Conclusion: generational countermeasures considering factors of psychosocial work environment and life conditions are needed to avert female nurse turnover.

Microaggressions are subtle verbal and non-verbal slights based on group membership, and they are ubiquitous in the lives of racial minorities, women, and LGBTQ individuals (Sue, 2010). The goal of the current paper is to introduce a role-playing based exercise on effective responses to microaggressions. The workshop draws on the prejudice responding workshops of Plous (2000) and Lawson, et al. (2010) but integrates research-based strategies. The activity was tested in two groups of undergraduate students, and the findings suggested that both groups felt more prepared to deal with microaggressions after participating.

Monochromatic documents claim for much less computer bandwidth for network transmission and storage space than their color or even grayscale equivalent. The binarization of historical documents is far more complex than recent ones as paper aging, color, texture, translucidity, stains, back-to-front interference, kind and color of ink used in handwritting, printing process, digitalization process, etc. are some of the factors that affect binarization. This article presents a new binarization algorithm for historical documents. The new global filter proposed is performed in four steps: filtering the image using a bilateral filter, splitting image into the RGB components, decision-making for each RGB channel based on an adaptive binarization method inspired by Otsu's method with a choice of the threshold level, and classification of the binarized images to decide which of the RGB components best preserved the document information in the foreground. The quantitative and qualitative assessment made with 21 binarization algorithms in three sets of “real world” documents showed very good results.

HER2/neu positive breast tumors predict a high mortality and comprise 25-30% of breast cancer. We have shown that Flavokawain A (FKA) preferentially reduces the viabilities of HER2 overexpressing breast cancer cell lines (i.e. SKBR3 and MCF7/HER2) versus those with less HER2 expression (i.e. MCF7 and MDA-MB-468). FKA at cytotoxic concentrations to breast cancer cell lines also has minimal effect on the growth of non-malignant breast epithelial MCF10 cells. FKA induces G2M arrest in cell cycle progression of HER2 overexpressing breast cancer cell lines through inhibition of Cdc2 and Cdc25C phosphorylation and down-regulation of Myt1 and Wee1expression leading to increased Cdc2 kinase activities. In addition, FKA induces apoptosis in SKBR3 cells by increasing the protein expression of Bim and BAX and decreasing expression of Bcl₂, Bcl_x/L , XIAP and survivin. FKA also down-regulates the protein expression of HER-2 and inhibits AKT phosphorylation. Herceptin plus FKA treatment leads to enhanced growth inhibitory effect on HER-2 overexpressing breast cancer cell lines through down-regulation of Myt1, Wee1, Skp2, Survivin and XIAP. Our results suggest the promise of FKA as a novel apoptosis inducer and G2 checkpoint abrogating agent in combination with Herceptin for treatment of HER2 overexpressing breast cancer.

The migration from MATLAB to Python (M-to-PY) has gained significant traction in recent computational research. While MATLAB has long served as a linchpin in myriad scientific endeavors, there's an emerging trend to rejuvenate these projects using Python's extensive AI tools and libraries. This study presents a semi-automated process for M-to-PY conversion, using a detailed case study of an image skeletonization project comprising fifteen MATLAB files and a 1404-image dataset. Skeletonization is foundational for ongoing 3D motion detection research using AI transformers, predominantly developed in Python. The utilization of ChatGPT-4, acting as an AI co-programmer, is pivotal in this conversion. By leveraging the public OpenAI API, we developed an M-to-PY converter prototype, evaluated its efficacy using test cases from the Bard bot, and subsequently employed the converted code in an AI application. The dual contributions encompass a well-tested M-to-PY converter and a Skeleton App capable of sketching and skeletonizing any given image, enriching the AI toolset. This study accentuates how AI resources, like ChatGPT-4, can simplify code transitions, opening doors for innovative AI implementations using primarily MATLAB-coded scientific research.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

The world has been highly impacted by the COVID-19 as the virus has spread to all continents – about 200 countries in total. The latest update claims about 4,000,000 confirmed cases and about 300,000 confirmed deaths owing to the COVID-19 pandemic. This probably makes the COVID-19 as the most dangerous contagious disease in the era 2000s. Apart from massive publications on this topic, there is no available qualitative analysis that describes the dynamic spreads of the COVID-19 and its impacts on healthcare and the economy. Through the system archetypes analysis, this paper explains that the dynamic spread of the COVID-19 consists of the limits to growth and the success to successful structures. The limits to growth elucidates that more symptomatic and asymptomatic patients owing to infected droplets may be bounded by self-healing and isolated treatments. The success to successful structure explains that once the COVID-19 affects the economy through the lockdown, there will be a limited fund to support the government aids and the aggregate demand. In overall, this paper gives readers simplified holistic insights into understanding the dynamic spread of the COVID-19.