Sulphuric acid is a widely used raw material in the chemical industry. Its corrosive effect on materials varies considerably, depending on impurities, temperature and water content. Accordingly, good corrosion resistance under all conditions is very difficult to achieve. This is especially an issue for micro process apparatus with very thin walls. Furthermore, such devices are often joint by diffusion bonding what may alter materials properties due to high temperatures and long dwell times. In fact, for each new material, the diffusion bonding parameters must be optimized and the impact on mechanical as well as corrosion properties must be investigated. In this paper, two high molybdenum alloys, namely Hastelloy B3 and BC-1, were evaluated. Diffusion bonding tests were performed using ten layers of sheet material in between round stock. Corrosion tests were performed in 70 % sulphuric acid at 100°C for 1000 h. Tensile tests on both alloys were carried out for different material conditions, to determine the change in mechanical strength and elongation at fracture values. In general, independent of the condition of the materials, the fracture behavior of both alloys was found to be ductile and the specimens show the typical dimple structure, in the case of diffusion bonded samples, interrupted by weak spots or rather non-bonded areas. These areas are obviously causing the onset of material failure and thus, a degradation of mechanical properties. Tensile samples, that were aged in 70% sulphuric acid at 100°C for 1000 hours showed local corrosion attacks at the grain boundaries at the circumferential surfaces and especially at the joining planes – for Hastelloy B3 much more pronounced than for Hastelloy BC-1. Accordingly, a further decrease of both, the stress- and elongation at fracture values is observed. However, the typical material parameters like 0.2 % yield strength used for dimensioning components are found to be sufficient high, even when operating the materials under such harsh conditions. When concluding the results, at least Hastelloy BC-1 reveals both sufficient good mechanical properties and an excellent corrosion resistance, regardless of the heat treatment, and could be considered for manufacturing micro-process engineering apparatuses operated in a sulphuric acid environment. This is a significant advance compared to the results obtained within a AiF project, previously carried out on four different materials to investigate the corrosion resistance in sulphuric acid.

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

Unsupervised metric learning has been generally studied as a byproduct of dimensionality reduction or manifold learning techniques. Manifold learning techniques like Diusion maps, Laplacian eigenmaps has a special property that embedded space is Euclidean. Although laplacian eigenmaps can provide us with some (dis)similarity information it does not provide with a metric which can further be used on out-of-sample data. On other hand supervised metric learning technique like ITML which can learn a metric needs labeled data for learning. In this work propose methods for incremental unsupervised metric learning. In rst approach Laplacian eigenmaps is used along with Information Theoretic Metric Learning(ITML) to form an unsupervised metric learning method. We rst project data into a low dimensional manifold using Laplacian eigenmaps, in embedded space we use euclidean distance to get an idea of similarity between points. If euclidean distance between points in embedded space is below a threshold t₁ value we consider them as similar points and if it is greater than a certain threshold t₂ we consider them as dissimilar points. Using this we collect a batch of similar and dissimilar points which are then used as a constraints for ITML algorithm and learn a metric. To prove this concept we have tested our approach on various UCI machine learning datasets. In second approach we propose Incremental Diusion Maps by updating SVD in a batch-wise manner.

Innovations in drug delivery systems are crucial for enhancing therapeutic efficiency. Our research presents a novel approach based on Electro-fluid dynamic atomization (EFDA) to fabricate core-shell monophasic particles (CSMp) from sodium alginate blends of varying molecular weights. This study explores the morphological characteristics of these particles in relation to material properties and process conditions, highlighting their potential in drug delivery applications. A key aspect of our work is the development of a mathematical model that simulates the release kinetics of small molecules, specifically sodium diclofenac. By assessing the diffusion properties of different molecules and gel formulations through transport and rheological models, we have created a predictive tool for evaluating the efficiency of these particles in drug delivery. Our findings underscore two critical independent parameters for optimizing drug release: the external shell thickness and the diffusivity ratios within the dual layers. This allows for precise control over the timing and intensity of the release profile. The study advances our understanding of EFDA in the fabrication of CSMp and offers promising avenues for enhancing drug delivery systems by tailoring release profiles through particle characteristic manipulation.

Person Re-identification is the task of recognizing comparable subjects across a network of nonoverlapping cameras. This is typically achieved by extracting from the source image a vector of characteristic features of the specific person captured by the camera. Learning a good set of robust, invariant and discriminative features is a complex task, often leveraging contrastive learning. In this article, we explore a different approach, learning the representation of an individual as the conditioning information required to generate images of the specific person starting from random noise. In this way we decouple the identity of the individual from any other information relative to a specific instance (pose, background, etc.), allowing interesting transformations from one identity to another. As generative models, we use the recent diffusion models that have already proven their sensibility to conditioning in many different contexts. The results presented in this article serve as a proof-of-concept. While our current performance on common benchmarks is lower than state-of-the-art techniques, the approach is intriguing and rich of innovative insights, suggesting a wide range of potential improvements along various lines of investigation.

Agriculture is pivotal in national economies, with pest detection significantly influencing food quality and quantity. Pest classification remains challenging in automated agriculture monitoring systems, exacerbated by the non-uniform pest scales and the scarcity of high-quality datasets. In this study, we constructed a pest dataset by acquiring domain-agnostic images from the Internet and resizing them to a standardized 299x299 pixel format. Additionally, we employed diffusion models to generate supplementary data. While Convolutional Neural Networks (CNNs) are prevalent for prediction and classification, they often lack effective global information integration and discriminative feature representation. To address these limitations, we propose the RS Transformer, an innovative model that combines elements like the Region Proposal Network, Swin Transformer, and ROI Align. Additionally, we introduce the Randomly Generated Stable Diffusion Dataset (RGSDD) to augment the availability of high-quality pest datasets. Extensive experimental evaluations demonstrate the superiority of our approach compared to both two-stage models (SSD and Faster R-CNN) and one-stage models (YOLOv3, YOLOv4, YOLOv5m, YOLOv8, and DETR). We rigorously assess performance using metrics such as mean Average Precision (mAP), F1Score, Recall, and mean Detection Time (mDT). Our research contributes to advancing pest detection methodologies in automated agriculture systems, promising improved food production and quality.

The current study primarily aimed to simulate detonation initiation via turbulent jet flame acceleration in partial-premixed H2-air mixtures. Different vertical concentration gradients were generated by varying the duration of hydrogen injection (referred to as diffusion time) within an enclosed channel filled with air. H2-air mixtures with average hydrogen concentrations of 22.5% (lean mixture) and 30% (near stoichiometric mixture) were investigated at diffusion times of 3, 5, and 60 seconds. Numerical results show that the vertical concentration gradient has a major influence on the early-stage of flame acceleration (FA). In the stratified lean mixture, detonation began in all the diffusion times, and comparing the flame-speed graphs showed that a decrease in the diffusion time and an increase in the mixture inhomogeneity speeded up the flame propagation and the jet flame to detonation transition occurrence in the channel. In the stratified H2-air mixture with an average hydrogen concentration of 30%, transition from a turbulent jet flame to detonation occurred in all the cases, and the mixture inhomogeneity weakened the FA and delayed the detonation initiation.

The introduction on Zinc oxide nanoparticles (ZnOn) in sunscreens solved the issue of poor spreadability of these formulations, which often left a white film on the skin. However, safety concerns have arisen regarding the topical application of ZnOn. Some studies employed commercial sunscreens to address the safety issues of the topical application of ZnOn; however, commercial formulations are often complex and contain a wide range of ingredients that could attenuate the potential damage caused by the ZnOn. Therefore, in this study we aimed to develop a simple stable formulation containing 20% of coated and uncoated ZnOn, characterize the formulations and the nanoparticles, and assess the skin penetration in Franz diffusion cell. The Feret's diameter for the uncoated and coated ZnOn was 137 nm and 134 nm, respectively. For the uncoated ZnOn the hydrodynamic size in water was 368 nm and for the coated ZnOn, the average hydrodynamic size in ethyl acetate was 135 nm. The incorporation of ZnOn led to formulations more consistent and easier to spread, as suggested by the lower work of shear and higher values of firmness, cohesiveness, consistency and index of viscosity compared with the vehicle. The stability assessment at 45ºC suggested that the formulations containing the ZnOn were stable for 30 days and the vehicle was stable for 90 days. The assessment off the skin penetration by reflectance confocal laser microscopy indicated that the formulations did not permeate into the deepest layers of the skin, but accumulated on the skin furrows, hair and hair follicle.

In this study, a new approach to pesticide permeation through the apple peel into the pulp is discussed. The tested compounds can be classified, based on mode of action, as systemic (boscalid, cyprodinil, pirimicarb, propiconazole and tebuconazole) or contact (captan, cypermethrin and fludioxonil) pesticides. The barrier effect was assessed using a Franz flow-type vertical diffusion cell system. Residue analysis was performed using a modified quick, easy, cheap, efficient, rugged and safe (QuEChERS) extraction method coupled to gas chromatography with tandem mass spectrometry (GC-MS/MS). The limits of detection (LODs) ranged between 2.6 µg kg-1 (pirimicarb) and 17 µg kg-1 (captan), with the coefficient of variability (CV) lower than 6%, while recoveries ranged from 85% (boscalid) to 112% (captan) at 0.1 and 1 mg kg-1 spiked levels. The highest peel penetration was observed for pirimicarb, captan and cyprodinil, with cumulative permeation of 90, 19 and 17 µg cm-2, respectively. The total absorption was in the range from 0.32% (tebuconazole) to 32% (pirimicarb). Only cypermethrin was not quantitatively detected in the pulp and its use can be recommended in crop protection techniques. The obtained results indicate that molecular weight, octanol-water partition coefficient and water solubility are important parameters determining the process of pesticide absorption.

This paper presents a numerical method for solving a two-dimensional subdiffusion equation with a Caputo fractional derivative. The problem considered assumes symmetry in both the equation’s solution domain and the boundary conditions, allowing for a reduction of the two-dimensional equation to a one-dimensional one. The proposed method is an extension of the fractional Crank-Nicolson method, based on the discretization of the equivalent integral-differential equation. To validate the method, the obtained results were compared with a solution obtained through Laplace transform. The analytical solution in the image of the Laplace transform was inverted using the Gaver-Wynn-Rho algorithm implemented in the specialized mathematical computing environment, Wolfram Mathematica. The results clearly show the mutual convergence of the solutions obtained by the two methods.

The reference method for cefiderocol antimicrobial susceptibility testing is broth microdilution (BMD) with iron-depleted-Mueller-Hinton (ID-MH) medium, whereas breakpoints recommended for disk diffusion (DD) are based on MH-agar plates. We aimed to compare the performance of the commercial BMD tests ComASP (Liofilchem) and UMIC (Bruker), DD and E-test using MH- and ID-MH-agar plates with the reference BMD method using 100 carbapenem-resistant-A. baumannii isolates. Standard BMD was performed according to the EUCAST guidelines, DD and E-test were carried out using two commercial MH-agar plates (bioMérieux and Liofilchem) and an in-house ID-MH-agar plate, while ComASP and UMIC were performed according to the manufacturer’s guidelines. DD performed with the ID-MH-agar plates led to a higher categorical agreement (CA, 95.1%) with standard BMD and fewer categorization errors compared to the commercial MH-agar plates (CA bioMérieux 91.1%, Liofilchem 89.2%). E-test on ID-MH-agar plates exhibited a significantly higher essential agreement (EA, 75%) with standard BMD compared to the two MH-agar plates (EA bioMérieux 57%, Liofilchem 44%), and showed a higher performance in detecting high-level resistance than ComASP and UMIC (mean log2 difference with standard BMD for resistant isolates of 0.5, 2.83 and 2.08, respectively). In conclusion, DD and E-test on ID-MH-agar plates exhibit a higher diagnostic performance than on MH-agar plates and the commercial BMD methods. Therefore, we recommend using ID-MH-agar plates for cefiderocol susceptibility testing of A. baumannii.

The purpose of this paper is to study the influence of diffusion and thermal loading due to pulsed laser heating on a thermoelastic solid with voids in the context of the model of three-phase-lag. The non-dimensional governing equations are formulated and then the exact expressions for the temperature field, the displacement components, the stress components, the concentration field and the change in the volume fraction field are obtained using the normal mode technique. The material is an isotropic, homogeneous elastic half-space and heated by a non-Gaussian laser beam with pulse duration of ps. The magnesium crystal element is used as an application to compare the predictions induced by diffusion and laser pulse on poro-thermoelastic medium of the model of three-phase-lag with those for the theory of Green–Naghdi of type III. The results obtained for thermal changes are verified by comparison with two theories of thermoelasticity, namely the model of three-phase lag (3PHL) and the Green and Nagdi type III theory. Plot the expressions to examine the effect of the laser pulse at two different values of time and the effect void parameter. This study also yields some interesting special cases.

Recent advances in synthetic membranes allow their use in fields as diverse as food and agriculture, biotechnology, industrial wastewater treatment, and potable water production. Among the newly developed technologies, nanofiltration for liquids and more particularly for desalination of seawater or saline aquifers are actively pursued. However, current solid-state membranes performance is limited, which calls for the development of novel formulations for membranes offering both high permeability (ion and water flux) and ion differentiation (selectivity), usually considered antagonist features. We report the development of hybrid nanoporous membranes made of solid-state polymeric carbonate track-etched (PCTE) thin films in which biological ion channels such as Gramicidin A (GA), alpha-hemolysin (α-HL), and outer-membrane protein F (OmpF) aquaporin are confined and graphene oxide (GO) conjugated cobalt ion selective binding peptide motifs (Copep) are adsorbed, referring as bioinspired and biomimetic approaches, respectively. These solid-state nanoporous membranes are attracting widespread attention since they offer scalability, mechanical robustness, selectivity, controlled pore dimension and shape, for water sustainability. The ion permeability, ion diffusion coefficient and selective ion recognition are evaluated via nanofiltration, cell diffusion kinetics, and UV-Visible absorption spectroscopy to gain insights into the role of key performance parameters including effective ion confinement in track-etched pores, rich surface chemistry, and peptide-induced channel for selective ion transport. These findings provide new avenues for artificial ion channels by synergistic combination of eco-friendly material design such as GO enabled by bio-molecular recognition chemistry.

The durability of ecological concrete in a marine environment was studied. Specimens of a six-year-old submerged ecological concrete from a breakwater located in the East Mediterranean sea were analyzed for their biological carbonate deposition cover, chloride effective diffusion, carbonation, and mineralogy. About 57% of the surface was found to be covered by biogenic-deposited carbonates. The effective chloride diffusion coefficient and the carbonation rate were found to be reduced proportionally to the biogenic-carbonate cover. Most of the aluminates were found in non-crystalline minerals. No evidence of a sulfate attack was found.

Background: As coronavirus (COVID-19) continues to pose a threat to the entire world, it is critical to developing strategies for containing its spread. The purpose of this study was to assess the demographic characteristics, brain tomography characteristics, and diffusion magnetic resonance findings of COVID-19 positive individuals. Material and Method: Between January 1 and December 31, 2021, 317 patients over the age of 18 were admitted to the emergency department with symptoms consistent with COVID-19. Three groups were formed based on clinical findings in patients, divided into light, medium, and severe, and four groups were formed based on radiological imaging findings. Results: The mean age of the 317 patients included in the study was 67.28±12.06 years, with a range of 28-91 years. The clinical classification of the patients was based on laboratory parameters and radiological imaging, not on their age or gender. Mild cases were classified as CO-RADS 0-4; moderate and severe cases were classified as CO-RADS 5-6 (p=0.001). While 60 (18.9%) of patients were followed outpatient, 144 (45.4%) were admitted to the hospital, 73 (23%) were admitted to the intensive care unit, and 40 (12.7%) died (p=0.001). Direct radiographs revealed bilateral involvement in 224 (70.7%) cases, peripheral involvement in 259 (81.7%) cases, and mid-lower lobe lung involvement in 194 (61.2%) cases (p=0.001). Brain tomography revealed infarction in 42 (13.2%) of the patients who were followed and hospitalized and hemorrhage in 22 (6.9%) of the patients. Magnetic resonance imaging revealed diffusion involvement in 68 (21.5%) of the cases (p=0.001). Conclusion: A standardized reporting system for COVID-19 data is required, and it must be simple to use, quick to understand, and focused on determining the risk of pneumonia. Additionally, the diagnostic role of radiological imaging, prognosis prediction, and severity scoring of lung involvement should be included.

Nonlinear catastrophes caused by geological fluids are a fundamental issue in rock mechanics and the geoengineering hazard field. For the consideration of hydrodynamic force on red-bed mudstone softening damage, X-ray visualization test on the fissure flow in mudstone block failure under hydrodynamic force was performed in this study based on block scale and the physical phenomena of fissure seepage and nonlinear diffusion were further explored. A new method for evaluating the hydro-damage degrees of rocks using an X-ray image analysis was proposed, and the quantitative relation of diffusion coefficients of hydro-damage and seepage was established. The research results revealed that the hydrodynamic force promoted the fluid-filled fissure behavior in mudstone specimen failure. Also, the seepage and diffusion phenomena of fluid in rocks during failures were indicated using X-ray imaging. A dual mechanical behavior was presented in the nonlinear seepage and abnormal diffusion of a red mudstone geological body under hydrodynamic conditions. The damaged degree of mudstone was aggravated by the effect of hydrodynamic force, and the initial seepage–diffusion coefficient with respect to lower hydro-damage was larger than the final seepage–diffusion coefficient with respect to higher hydro-damage of rocks with a decreasing nonlinear trend.

Gradient-domain image processing is a technique where, instead of operating directly on the image pixel values, the gradient of the image is computed and processed. The resulting image is obtained by reintegrating the processed gradient. This is normally done by solving the Poisson equation, most oftenly by means of a finite difference implementation of the gradient descent method. However, this technique in some cases lead to severe haloing artefacts in the resulting image. To deal with this, local or anisotropic diffusion has been added as an ad-hoc modification of the Poisson equation. In this paper, we show that a version of anisotropic gradient-domain image processing can result from a more general variational formulation through the minimisation of a functional formulated in terms of the eigenvalues of the structure tensor of the differences between the processed gradient and the gradient of the original image. Example applications of linear and non-linear local contrast enhancement and colour image daltonisation illustrate the behaviour of the method.

For the past few decades, researchers have been intrigued with glassy polymers, which have applications ranging from gas separations to corrosion protection to drug delivery systems. The techniques employed to examine the sorption and diffusion of small molecules in glassy polymers are the subject of this review. Diffusion models in glassy polymers are regulated by Fickian and non-Fickian diffusion, with non-Fickian diffusion being more prevalent. The characteristics of glassy polymers are determined by sorption isotherms, and different models have been proposed in the literature to explain sorption in glassy polymers during the last few years. This review also includes the applications of glassy polymer. Despite having so many applications, current researchers still have difficulty in implementing coating challenges due to issues like as physical ageing, which is briefly discussed in the review.

Background: Glioblastoma is the deadliest, yet most common, brain tumor in adults, with poor survival and response to aggressive therapy. Therapeutic failure results from a number of causes inherent to these tumors. Imaging, computational, and drug delivery approaches can aid in the quest to access and kill each tumor cell in patients. One factor, interstitial fluid flow, is a driving force therapeutic delivery. However, convective and diffusive transport mechanisms are un-der-studied. In this study, we examine the application of a novel image analysis method to meas-ure fluid flow and diffusion in glioblastoma patients with MRI and compare to patient outcomes. Methods: Building on a prior imaging methodology tested and validated in vitro, in silico and in preclinical models of disease, here we apply our analysis method to archival patient data from the Ivy GAP dataset. Results: We characterize interstitial fluid flow and diffusion patterns in patients. We find strong correlations between flow rates measured within tumors and in the surrounding parenchymal space, where we hypothesized that velocities would be higher. Looking at overall magnitudes, there is significant correlation with both age and survival in this patient cohort. Additionally, we find that tumor size nor resection significantly alter the velocity magnitude. Last, we map the flow pathways in patient tumors and find variability in degree of directionality that we hypothesize in future studies may lead to information concerning treatment, invasive spread, and progression. Conclusions: Analysis of standard DCE-MRI in patients with glioblastoma offers more infor-mation regarding transport within and around tumor, can be measured post-resection and mag-nitudes correlate with patient prognosis.

The general coupling between particle transport and ionization-recombination processes in hot plasma is considered on the key concept of equilibrium charge state (CS) transport. A theoretical interpretation of particle and CS transport is gained in terms of a two-dimensional (2D) Markovian stochastic (random) processes, a discrete 2D Fokker-Plank-Kolmogorov equation (in charge and space variables) and generalized 2D coronal equilibrium between atomic processes and particle transport. The basic tool for analysis of CS equilibrium and transport is the equilibrium cell (EC) (two states on charge and two on space), which presents (i) a unit phase volume, (ii) the characteristic scale of local equilibrium, (iii) a comprehensive solution for the simplest nonlinear relations between transport and atomic processes. The approach opens up new perspectives on transport studies: (i) the direct modelling of equilibrium and transport of impurity using the atomic data base, (ii) recovery of the complete recombination rate profile based on knowledge of density profiles and ionization rate profiles, (iii) the local transport analysis, based on the reduction of the equilibrium set to the single EC (in particular, central or edge), (iv) analysis of the reduced transport coefficients (diffusion and convection) on the density profile measurements.

This study aimed to identify the utility of diffusion-weighted magnetic resonance (MR) imaging with an apparent diffusion coefficient (ADC) map as a predictor of the intrahepatic response of hepatocellular carcinoma (HCC) to cisplatin-based hepatic arterial infusion chemotherapy (HAIC). We retrospectively evaluated 113 consecutive patients with HCC who underwent gadoxetic acid-enhanced and diffusion-weighted MR imaging. The appropriate cutoff for the tumor-to-liver ADC ratio was determined to be 0.741. Of the 113 patients, 51 (45%) presented with a tumor-to-liver ADC ratio < 0.741. Evaluation of the intrahepatic treatment response after 2-3 cycles of HAIC in these 51 patients revealed that 20 patients (39%) experienced an objective response to HAIC. On the other hand, only 10 of the 62 patients with a tumor-to-liver ADC ratio ≥ 0.741 (16%) experienced an objective response. Thus, the objective response rate was significantly higher in patients with a tumor-to-liver ADC ratio < 0.741 than in those with a tumor-to-liver ADC ratio ≥ 0.741 (P = 0.006). Multivariate logistic regression analysis using parameters including perfusion alteration, percentage of a non-enhancing portion, and tumor-to-liver ADC ratio revealed that a tumor-to-liver ADC ratio < 0.741 (odds ratio 3.03; P = 0.015) is the sole predictor of an objective response to HAIC. Overall survival rates were significantly higher in patients with objective responses to HAIC than in those without objective responses (P = 0.001 by log-rank test). In conclusion, patients with unresectable HCC with a tumor-to-liver ADC ratio < 0.741 showed a favorable intrahepatic response to HAIC. Therefore, diffusion-weighted MR imaging can play a critical role as a predictor of response to cisplatin-based HAIC in unresectable HCC.

In this paper the dynamics of spatially extended infected phytoplankton with the Holling type II functional response and logistically growing susceptible phytoplankton system is studied. The proposed model is an extension of temporal model available [6], in spatiotemporal domain. The reaction diffusion system exhibits spatiotemporal chaos in phytoplankton dynamics. This is particularly important for the spatially extended systems that are studied in this paper as they display a wide spectrum of ecologically relevant behavior, including chaos. In this system stability of the system is studied with respect to disease contact rate and the growth fraction of infected phytoplankton indirectly rejoin the susceptible phytoplankton population. The results of numerical experiments in one dimension and two dimensions in space as well as time series in temporal models are presented using MATLAB simulation. Moreover, the stability of the corresponding temporal model is studied analytically. Finally, the comparison of the three types of numerical experimentations are discussed in conclusion.

Medical institutions, where several patients are treated and medical workers engaged, are always exposed to secondary viral and bacterial infections. It is critical to prevent infection transmission by indirect as well as direct contact through air or splash. The infections of most diseases can be transmitted through the air. HEPA filters installed in air conditioning equipment are used to prevent infection transmission through air in medical institutions, but air circulation takes a long time in a large space. Virus and bacteria smaller than 0.3 μm cannot be removed by the HEPA filter; hence, those microbes remain alive throughout the air ventilation. A plasma sterilizer has the capability to provide environmental friendly sterilization by employing reactive oxide species and reactive nitrogen species at a low cost. We developed an excellent plasma sterilizer by using a non-thermal atmospheric-pressure biocompatible plasma (NBP). Ozone concentration in plasma sources has been derived by Kuhn et al. [1]. The diffusion coefficients inside (D₀) and outside (D₁) the plasma sterilizer have been calculated to be 0.0641 m² s^-1 and 0.717 m² s^-1, respectively. To sustain high O₃ concentrations over 121 ppm inside the plasma source and low O₃ concentrations below 0.05 ppm outside the sterilizer, it is necessary to keep O₃ concentrations at the exit of plasma sterilizer below 0.28 ppm. so that diffusion coefficient D₁ has been designed to be as large as 11 times of D₀.

The central limit theorem (CLT) and its generalization to stable distributions have been widely described in literature. However, many variations of the theorem have been defined and often their applicability in practical situations is not straightforward. In particular, the applicability of the CLT is essential for a derivation of heterogeneous ensemble of Brownian particles (HEBP). Here, we analyze the role of the CLT within the HEBP approach in more detail and derive the conditions under which the existing theorems are valid.

This work deals with the numerical investigation of the delivery of potential therapeutic agents through dentinal discs (i.e. a cylindrical segment of the dentinal tissue) towards the dentin-pulp junction. The aim is to assess the main key features (i.e. molecular size, initial concentration, consumption rate, disc porosity and thickness) that affect the delivery of therapeutic substances to the dental pulp and consequently to define the necessary quantitative and qualitative issues related to a specific agent before its potential application in clinical practice. The CFD code used for the computational study is validated with relevant experimental data obtained using micro Laser Induced Fluorescence (μ-LIF) a non-intrusive optical measuring technique. As the phenomenon is diffusion dominated and strongly dependent on the molecular size, the time needed for the concentration of released molecules to attain a required value can be controlled by their initial concentration. Finally, a model is proposed which, given the maximum acceptable time for the drug concentration to attain a required value at the pulpal side of the tissue along with the aforementioned key design parameters, is able to estimate the initial concentration to be imposed and vice versa.

The aim of this work is to present a design approach of a Shock-Induced Combustion Ramjet (Shcramjet) inlet, and present its optimization in terms of the flow and geometrical parameters. The flow properties of mixed compression type inlet of a Shcramjet are examined using analytical and numerical techniques. The geometries obtained with variations in the wedge angles, length, height and cowl lip positions are used to study the flow characteristics of inlet, identifying bow shock temperature ratio as the optimization parameter. The two-dimensional geometries of two-shock and three-shock inlet models designed analytically for shock-on-lip condition at Mach 12.5 and an altitude of 32.5 km are numerically simulated in OpenFOAM CFD Toolbox. A density based compressible CFD solver based on central upwind schemes of Kurganov and Tadmore is used to solve 2D inviscid Euler equations. The inlet total pressure recovery is expressed as a function of temperature ratios of compression shocks, and is found to have a maxima at a bow shock temperature ratio at the design condition when the bow and external shocks have equal strengths. The effect of considering the flow to be calorically imperfect is studied numerically, and the deviation from the analytical design is presented.

This paper constituted an extension of two previous studies concerning the mathematical development of the grain boundary grooving in polycrystalline thins films in the cases of the evaporation/condensation and diffusion taken separately. The thermal grooving processes are deeply controlled by the various mass transfer mechanisms of evaporation–condensation, surface diffusion, lattice diffusion, and grain boundary diffusion. This study proposed a new original analytical solution to the mathematical problem governing the grain groove profile in the case of simultaneous effects of evaporation-condensation and diffusion in polycrystalline thin films submitted to thermal and mechanical stress, and fatigue effects; by resolving the corresponding fourth-order partial differential equation ∂y∂t=C∂2y∂x2-B∂4y∂x4 obtained from the approximation y'2≪1. The comparison of the new solution to that of diffusion alone proved an important effect of the coupling of evaporation and diffusion on the geometric characteristics of the groove profile. A second analytical solution based on the series development was also proposed. It was proved that change of the boundary conditions of the grain grooving profile largely affected the different geometric characteristics of the groove profile.

Predictions of mean values of statistical variables of large scale turbulent flow by the widely used basic k-ϵ model and a new fundamentally based model are verified against published results of Direct Numerical Simulations DNS of the Navier-Stokes equations. The verification concerns turbulent channel flow at shear Reynolds numbers of 950, 2000 and 104. The basic k-ϵ model is largely based on empirical formulations accompanied by calibration constants. This contrasts with the new model where descriptions of leading statistical quantities are based on the general principles of statistical turbulence at large Reynolds number. Predicted values of major output variables such as turbulent viscosity, diffusivity of passive admixture, temperature, and fluid velocities compare well with DNS in case of the new model. Significant differences are seen in case of the basic k-ϵ model.

Keywords: Amorphous-precipitate, Nitride, Morphological stability, Diffusion, Internal stresses, Modelling, Simulation

People are drawn to woodcut-style designs due to their striking visual impact and strong contrast. However, traditional woodcut prints and previous computer-aided methods have not addressed the issues of dwindling design inspiration, lengthy production times, and complex adjustment procedures. We propose a novel network framework, the Woodcut-style Design Assistant Network (WDANet), to tackle these challenges. Notably, our research is the first to utilize diffusion models to streamline the woodcut-style design process. We've curated the Woodcut-62 dataset, featuring works from 62 renowned historical artists, to train WDANet in absorbing and learning the aesthetic nuances of woodcut prints, offering users a wealth of design references. Based on a noise reduction network, our dual cross-attention mechanism effectively integrates text and woodcut-style image features. This allows users to input or slightly modify a text description to quickly generate accurate, high-quality woodcut-style designs, saving time and offering flexibility. As confirmed by user studies, quantitative and qualitative analyses show that WDANet outperforms the current state-of-the-art in generating woodcut-style images and proves its value as a design aid.

: Oscillation synchronization through diffusion-based communication of active materials can lead to emergence of diverse patterns and collective behaviors. A detailed general description of the formation process of synchronization or resynchronization dynamics is a challenging task. We employ a photosensitive Belousov-Zhabotinsky reaction-diffusion model (within a gel media) to investigate the recovery process of oscillation synchronization between a pair of gel patches. The recovery time for oscillation resynchronization can be modulated by patch-distance, species of signaling molecules, intensity and duration of illumination. Analysis reveals that the “switch effect” of the gel-distance and the “promotion effect” from illumination on the oscillation resynchronization originate from the competition between processes of photo-promotion of oscillation, diffusion of signaling molecules (HBrO2 and Br-) and disproportionation of HBrO2. These results will benefit studies on bio-inspired active materials and soft motors.

LiFePO4 (LFP) has undergone extensive research and is a promising cathode material for Li-ion batteries. The high interest is due to its low raw material cost, good electrochemical stability, and high-capacity retention. However, poor electronic conductivity and a low Li+ diffusion rate decrease its electrochemical reactivity, especially at fast charge/discharge rates. In this work, the volumetric energy density of lithium-ion batteries is successfully increased by using different amounts of conductive carbon (Super P) in the active material content. The particle size and morphology of the electrode material samples are studied using field emission scanning electron microscopy and dynamic light scattering. Two-point-probe DC measurements and adhesive force tests are used to determine the conductivity and evaluate adhesion for the positive electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and charge/discharge tests are used to analyze the electrochemical properties of the battery. The samples containing 88% LFP, 5.5% Super P and 6.5% PVDF perform best, with discharge capacities reaching 169.8 mAhg-1 at 0.1C, and they can also manage charging/discharging of 5C. EIS indicates that this combination produces the lowest charge-transfer impedance (67 Ω) and the highest Li+ ion diffusion coefficient (5.76 x 10-14 cm2s-1).

The interactive approach implies that a heterogeneous group of actors cooperates to identify, develop, and introduce innovative solutions into the ground. 20-year studies showed this approach as the most suitable to support innovation and knowledge sharing in the agri-food system. With the introduction of the EIP initiative in the EU policy, this approach has become a privileged tool to support innovation within the CAP, via the implementation of Operational Groups. The present study aims to analyse how the interaction process works in the implementation of the OGs in Italy, and its effectiveness. An online survey submitted to 270 OGs and 10 in-depth case studies were used to analyse interaction process and its effectiveness in the Italian OGs. The results show that the EIP AGRI in Italy helped to capture the real issues of farmers and other actors in the rural territories. Furthermore, participation in the OGs supported the creation and strengthening of relationships between partners. The major difficulties were identified in maintaining active interaction in all phases of the projects and with all partners involved and in the traditional approach used for dissemination of results, both within and outside the partnership. The study showed how complex is to describe the processes triggered by the interactive approach, being it influenced by the type of relationships existing between partners and by other external factors.

Colorectal liver metastases (CRLM) patients combined with hepatic lymph node metastases was a negative prognostic factor associated with outcomes. Up to now, there was still lack of a reliable method to identify the status of hepatic lymph nodes. The aim of this study was to investigate the predictive ability of mono-exponential, bi-exponential, and stretched-exponential diffusion-weighted imaging (DWI) models to distinguish between benign and malignant hepatic lymph nodes in CRLM patients who underwent neoadjuvant chemotherapy prior to surgery. In total, 97 CRLM patients with pathologically proved hepatic lymph node status were included. Various quantitative parameters, including the apparent diffusion coefficient (ADC) from mono-exponential model, D, D*, and f derived from intravoxel incoherent motion (IVIM) model, as well as DDC and α from stretched-exponential model (SEM), were measured. Multivariate analysis revealed that the pre- treatment DDC value and the short diameter of the largest lymph node after treatment were independent predictors of metastatic hepatic lymph nodes. A nomogram combining these two factors demonstrated excellent performance in distinguishing between benign and malignant lymph nodes in CRLM patients, with an area under the curve (AUC) of 0.873. Therefore, the nomogram can serve as a preoperative assessment tool for determining the status of hepatic lymph nodes and aiding in the decision-making process for surgical treatment in CRLM patients.

Pentagalloyl glucose (PGG) is currently being investigated as a non-surgical treatment for abdominal aortic aneurysms (AAA); however molecular mechanisms of action of PGG on the AAA matrix components and the intra-luminal thrombus (ILT) still need to be better understood. To assess these interactions, we utilized peptide fingerprinting and molecular docking simulations to predict the binding of PGG to vascular proteins in normal and aneurysmal aorta, including matrix metalloproteinases (MMPs), cytokines and fibrin. We performed PGG diffusion studies in pure fibrin gels and human ILT samples. PGG was predicted to bind with high affinity to most vascular proteins, the active sites of MMPs, and several cytokines known to be present in AAA. Finally, despite potential binding to fibrin, PGG was shown to diffuse readily through thrombus at physiologic pressures. In conclusion, PGG can bind to all the normal and aneurysmal aorta protein components with high affinity, potentially protecting the tissue from degradation and exerting anti-inflammatory activities. Diffusion studies showed that thrombus presence in AAA is not a barrier to endovascular treatment. Together, these results provide a deeper understanding of the clinical potential of PGG as a non-surgical treatment of AAA.

Lipid mesophases are being intensively studied as potential candidates for drug-delivery purposes. Extensive experimental characterization has unveiled a wide palette of release features depending on the nature of the host lipids and of the guest molecule, as well as on the environmental conditions. However, only few simulation works have addressed the matter, which hampers a solid rationalization of the richness of outcomes observed in experiments. Particularly, to date there are no theoretical works addressing the impact of hydropathy on the transport of a molecule within lipid mesophases, despite the significant fraction of hydrophobic molecules among currently-available drugs. Similarly, the high heterogeneity of water mobility in the nanoscopic channels within lipid mesophases has also been neglected. To fill this gap, we introduce here a minimal model to account for these features in a lamellar geometry, and systematically study the role played by hydropathy and water-mobility heterogeneity by Brownian-dynamics simulations. We unveil a fine interplay between the presence of free-energy barriers, the affinity of the drug for the lipids, and the reduced mobility of water in determining the net molecular transport. More in general, our work is an instance of how multiscale simulations can be fruitfully employed to assist experiments in release systems based on lipid mesophases.

The effect of the communication channel size on the transport and subsequent detection of chemical messengers is investigated on millimetric and micrometric channels. The transport of the information carriers, being characterized by an advective and a diffusive contribution, was simulated by varying the flow velocity and the diffusion coefficient. Then, to evaluate the information quality, the Intersymbol Interference (ISI) between two consecutive signals at a specific release delay was estimated. This allowed us to verify that operating under micrometric channel conditions has a larger flow velocity range to obtain completely separated successive signals and smaller release delays can be used between signals. The theoretical results were confirmed by developing a prototype molecular communication platform operating under microfluidic conditions, which enables communication through fluorescent nanoparticles, namely Carbon Quantum Dots (CQDs).

Although lithium-ion batteries have extensively been used in various applications because of their high energy capacity, fracture and failure, the by-products of large strains and stresses caused by fast charging and discharging need yet to be addressed. The size effects on the mechanical behavior of the nano-sized structures are significant; however, the classical elasticity theory may not consider such effects. On the other hand, surface stress theory, as a robust and potential theory, is suitable in considering size effects in nano-scale structures. Therefore, in this paper, in order to involve the surface stress effects on the fracture behavior of Li-ion batteries, the following steps are taken. Firstly, a phase-field model is used to determine the evolution of the concentration profile. Subsequently, the stress distribution is obtained by using the surface stress theory combined with chemical equations for a planar electrode. Afterward, by using the weight function method for an edge crack in the plate, the stress intensity factor is derived for all time steps and possible crack lengths during the process. It is found that with increasing phase boundary thickness parameter or decreasing phase-separation phenomenon, the surface mechanics parameters become more influential. Furthermore, in the presence of positive surface stress, the diffusion-induced stress distribution decreases, which in turn reduces the stress intensity factor. In addition, in this paper, the two states of surface stress are compared either for elastic or total strain. Concerning stresses and concentrations, the results indicate a big difference at the beginning of the deintercalation process showing, in particular, 2% for stresses, but the differences diminish gradually.

The steady-state, coupled heat and mass transfer from a fluid flow to a sphere accompanied by an exothermal catalytic chemical reaction on the surface of the sphere is analysed taking into consideration the effect of thermal radiation. The flow past the sphere is considered steady, laminar and incompressible. The radiative transfer is modeled by P₀ and P₁ approximations. The mathematical model equations were discretized by the finite difference method. The discrete equations were solved by the defect correction – multigrid method. The influence of thermal radiation on the sphere surface temperature, concentration and reaction rate was analysed for three parameter sets of the dimensionless reaction parameters. The numerical results show that only for very small values of the Prater number the effect of thermal radiation on the surface reaction is not significant.

In this paper, impulsive control on a single-species Markovian jumping ecosystem leads to a stability criterion, and the newly-obtained theorems improve the related existing results. Numerical examples illuminate the effectiveness.

Most of the existing influence maximization algorithms are not suitable for large-scale social networks due to their high time complexity or limited influence propagation range. Therefore, a D-RIS influence maximization algorithm is proposed based on the independent cascade model and combined with the reverse reachable set sampling. Under the premise that the influence propagation function satisfies monotonicity and submodularity, the D-RIS algorithm uses automatic debugging method to determine the critical value of the number of reverse reachable sets, which not only obtains a better influence propagation range, and greatly reduce the time complexity. The experimental results on the two real data sets of Slashdot and Epinions show that D-RIS algorithm is close to the CELF algorithm and higher than RIS algorithm, HighDegree algorithm, LIR algorithm and pBmH algorithm in influence propagation range. At the same time, it is significantly better than the CELF algorithm and RIS algorithm in running time, which indicates that D-RIS algorithm is more suitable for large scale social network.

In this study, a novel porous geopolymer mortar (GP) was produced and tested experimentally. Industrial waste materials/by-products were used as constituents of the GP, along with dune sand. One sample was produced as a control sample for benchmarking. For the rest of the samples, 15%, 30%, and 45% by volume, the solid constituents were replaced with expanded polystyrene foam (EPS) beads. These mortar samples were heat cured to depolymerize the EPS to cause porosity inside the samples. Indoor experiments were conducted to evaluate the response of produced porous GP to high heat flux. The porous samples were able to reduce heat transmission across the opposite surfaces. Induced porosity resulted in a decrement in compressive strength from 77.2 MPa for the control sample to 15.8 MPa for 45% porous sample. However, the limit lies within the standards for partitioning walls in buildings and pavements in urban areas to absorb rainwater.

In this paper, Lyapunov-Razumikhin technique, design of state-dependent switching laws, a fixed point theorem and variational methods are employed to derive the existence and the unique existence results of (globally) exponentially stable positive stationary solution of delayed reaction-diffusion cell neural networks under Dirichlet zero boundary value, including the global stability criteria \textbf{in the classical meaning}. Next, sufficient conditions are proposed to guarantee the global stability invariance of ordinary differential systems under the influence of diffusions. New theorems show that the diffusion is a double-edged sword in judging the stability of diffusion systems. Besides, an example is constructed to illuminate that any non-zero constant equilibrium point must be not in the phase plane of dynamic system under Dirichlet zero boundary value, or it must lead to a contradiction. Next, under Lipschitz assumptions on active function, another example is designed to prove that the small diffusion effect will cause the essential change of the phase plane structure of the dynamic behavior of the delayed neural networks via a Saddle point theorem. Finally, a numerical example illustrates the feasibility of the proposed methods.

Biophoton emission has been experimented for decades. The photo-genic origin of biophoton has also been attributed to the oxidative stress or free radical production. However, there are considerable gaps in quantitative understanding of biophoton emission. In this work, I propose an analytical hypothesis for interpreting a few patterns of steady-state biophoton emission of human, including the dependency on age, the diurnal variation, and the geometric asymmetry associated with serious asymmetrical pathological conditions. The hypothesis is based on an alternative form of energy state, termed vivo-nergy, which is associated with only metabolically active organisms that are also under neuronal control. The hypothesis projects a decrease of the vivo-nergy in human during growth beyond puberty. The hypothesis also proposes a modification of the vivo-nergy by the phases of systematic or homeostatic physiology. The hypothesis further postulates that the deviation of the physiology-modified vivo-nergy from the pre-puberty level is deteriorated by acquired organ-specific pathological conditions. A temporal differential change of vivo-nergy is hypothesized to proportionally modulate oxidative stress that functions as the physical source of biophoton emission. The resulted steady-state diffusion of the photon emitted from a photo-genic source in a human geometry simplified as a homogeneous spherical domain is modeled by photon diffusion principles incorporating an extrapolated zero-boundary condition. The age and systematic physiology combined determines the intensity of the centered physiological steady-state photo-genic source. An acquired pathology sets both the intensity and the off-center position of the pathological steady-state photo-genic source. When the age-commemorated, physiology-commanded, and pathology-controlled modifications of the steady-state photo-genetic sources are implemented in the photon diffusion model, the photon fluence rate at the surface of the human-representing spherical domain reveals the patterns on age, the temporal variation corresponding to systematic physiology, and the geometric asymmetry associated with significant asymmetric pathological condition as reported for spontaneous biophoton emission. The hypothesis, as it provides conveniences for quantitative estimation of biophoton emission patterns, will be extended in future works towards interpreting the temporal characteristics of biophoton emission under stimulation.

Plastic flow in body-centered cubic (bcc) alloys is governed by the thermally-activated screw dislocation motion. In bcc interstitial solid solutions, solute diffusion can occur at very fast rates owing to low migration energies and solute concentrations. Under mechanical loading, solutes may move on the same or similar time scale as dislocations glide, even at low temperatures, potentially resulting in very rich co-evolution processes that may have important effects in the overall material response. It is therefore important to accurately quantify the coupling between interstitial impurities and dislocations, so that larger-scale models can correctly account for their (co)evolution. In this paper, we use electronic structure calculations to obtain the energetics of oxygen diffusion under stress and its interaction energy with screw dislocation cores in bcc tungsten. We find that oxygen atoms preferentially migrate from tetrahedral to tetrahedral sites with an energy of 0.2 eV. This energy couples only weakly to hydrostatic and deviatoric deformations, with activation volumes of less than $0.02$ and $0.2b^3$, respectively. The strongest effect is found for the inelastic interaction between O atoms and screw dislocation cores, which leads to attractive energies on the order of 1.5 eV and a structural transformation of the screw dislocation core from an `easy' to a `hard' core configuration

Protein-DNA interactions are critical for the successful functioning of all natural systems. The key role in these interactions is played by processes of protein search for specific sites on DNA. Although it has been studied for many years, only recently microscopic aspects of these processes became more clear. In this work, we present a review on current theoretical understanding of the molecular mechanisms of the protein target search. A comprehensive discrete-state stochastic method to explain the dynamics of the protein search phenomena is introduced and explained. Our theoretical approach utilizes a first-passage analysis and it takes into account the most relevant physical-chemical processes. It is able to describe many fascinating features of the protein search, including unusually high effective association rates, high selectivity and specificity, and the robustness in the presence of crowders and sequence heterogeneity.

This paper presents a Modified Gate Diffusion Input (MGDI) design with four inputs for Quantum-dot Cellular Automata (QCA) technology. QCA is a promising nanotechnology that offers benefits such as low power consumption, and high density, making it a potential alternative to CMOS technology. The proposed planar cell design has advantages over previous designs, including a 19% reduction in the number of cells, a 29% reduction in total energy consumption, and a 44% reduction in average energy loss at the same occupancy level. The proposed block is capable of implementing 21 basic combinational functions and various sequential functions. The simulation of functions in 18nm technology and energy consumption calculation indicates that the resulting circuits have improvements of 41%, 27%, 27%, and 20% compared to multiplexers, comparators, four-bit parity circuits, and single-bit memory, respectively. Additionally, the number of cells in the proposed circuits has improved by 10%, 7%, 22%, and 19%, respectively.

Redox-flow batteries are rechargeable batteries that store energy in two liquid electrolytes, separated by a membrane. During charging and discharging, the electrolytes flow through the membrane and undergo chemical reactions that generate or consume electrical energy. These batteries are known for their scalability and long cycle life and are versatile energy storage technologies developed to enhance efficiency and lower costs. Deep Eutectic Solvents (DES) are eco-friendly alternatives to traditional electrolytes, and their properties have been studied to improve the performance of redox-flow batteries. We investigated choline chloride/ethylene glycol (ChlCl/Eg) mixtures with LiPF6 salt at four concentrations through experimental and MD simulations. The thermophysical and transport properties of the mixture, including density, diffusion coefficient, viscosity, and ionic conductivity, were calculated across a temperature range of 298.15–398.5 K. Our findings indicate that an increase in salt concentration leads to a decrease in diffusion coefficients and ionic conductivity, while increasing the viscosity of the deep eutectic solvent. This research provides valuable insights into the behavior of DES mixtures and can aid in the design and optimization of DES-based processes for use in redox-flow batteries.

The fractional diffusion equations with integrals play a significant role in describing anomalous diffusion phenomena. We first construct an appropriate resolvent family, and use the convolution theorem of Laplace transform, the probability density function, Cauchy integral formula and Fubini theorem to study its related equicontinuity, strongly continuity, compactness, etc. Then, a reasonable mild solution is defined. Finally, by combining some fixed point theorems, we obtain some conclusions on the existence and uniqueness of mild solutions.

Binarization of degraded documents is an important preprocessing task for various document analysis such as OCR and historical document analysis. Existing studies have applied various convolutional neural network (CNN) models and generative models for document binarization, but they do not show generalized performance for noise that the model has not seen and it suffers from extracting elaborate text strokes. In this paper, to overcome these challenges, we utilize latent diffusion model (LDM), which is known for high-quality image generation model, for the first time in document binarization. By utilizing the iterative diffusion-denoising process in latent space, it shows high-quality cleaned binarized image generation and high generalized performance through using both data distribution and time step while training. Additionally, we apply gated U-Net to the backbone network to preserve text strokes using trainable gating value. Gated convolution can extract elaborate text stroke by allowing the model to focus on text region by combining gating value and feature. Furthermore, we maximize the effectiveness of the proposed model by training it with a combination of LDM loss and pixel-level loss, which is suitable for the model structure. Experiments on H-DIBCO and DIBCO benchmark datasets show that the proposed model outperforms existing methods.

TThis paper delves into the extension and characterization of radial positive definite functions into non-integer dimensions. We provide a thorough investigation by employing the Riemann-Liouville fractional integral and fractional Caputo derivatives, enabling a comprehensive understanding of these functions. Additionally, we introduce a secondary characterization based on the Bernstein characterization of completely monotone functions. The practical significance of our study is showcased through an examination of the positivity of the fundamental solution of the space-fractional Bessel diffusion equation, highlighting the real-world applicability of the developed concepts. Through this work, we contribute to the broader understanding of radial positive definite functions and their utility in diverse mathematical and applied contexts.

Using analysis methods such as Rutherford backscattering Spectrometry, scanning electron microscopy, X-ray diffraction, and Raman spectroscopy, the diffusion behavior of iodine in micro/nano-porous graphite under high-temperature conditions was studied. The results indicate that iodine diffusion leads to the contraction of graphite microcrystals, a decrease in interlayer spacing, and an increase in defect density, resulting in a reduction in microcrystal size. Upon diffusion of iodine out of iodine-loaded graphite, the microcrystal size of the graphite increases, the interlayer spacing appears to return to the initial state, and the defect density decreases. By comparing the iodine diffusion performance of nanoporous graphite G400 and G450 with microporous graphite G500, it was determined that nanoporous graphite exhibits better inhibition of iodine diffusion compared to microporous graphite. Studying the diffusion behavior of iodine in micro/nano-porous graphite has significant academic significance and engineering value for the screening, design, and performance optimization of nuclear graphite.

Our aim is to provide an insight of the procedures and the dynamics that lead the spread of contagious diseases through populations. Our simulation tool can increase our understanding on the spatial parameters which affect the diffusion of a virus. SIR models are based on the hypothesis that populations are “well mixed”. Our model constitutes an attempt to focus on the effects of the specific distribution of the initially infected individuals through the population and provide insights, considering the stochasticity of the transmission process. For this purpose, we represent the population using a square lattice of nodes. Each node represents an individual that may or may not carry the virus. Nodes that carry the virus can only transfer it to susceptible neighboring nodes. This important revision of the common SIR model provides a very realistic property: the same number of initially infected individuals can lead to multiple paths, depending on their initial distribution in the lattice. This property creates better predictions and probable scenarios to construct a probability function and appropriate confidence intervals. Finally, this structure permits realistic visualizations of the results to understand the procedure of contagion and spread of a disease and the effects of any measures applied.

New analytical solutions of the heat conduction equation are presented in cylindrical and spherical coordinates. Then these solutions are reproduced with high accuracy by recent explicit and unconditionally stable finite difference methods. After this, real experimental data from the literature regarding a heated cylinder are reproduced by the explicit numerical methods as well as by Finite Element Methods (FEM) ANSYS workbench. Convection and nonlinear radiation are also considered on the boundary of the cylinder, and it is shown that the explicit methods are much more accurate than the commercial software.

This study aims to investigate the influence of various economic, environmental, and social factors on sustainable development, with a specific focus on the impact of green technology and climate change adaptation. A panel dataset comprising 38 OECD member countries from 1990 to 2020 is employed, and a series of dynamic panel data models are estimated using the system generalized method of moments (GMM) approach. Numerous covariates, such as globalization, socio-economic conditions, economic and political values, climate and technological progress, and environmental determinants, are examined. The empirical findings highlight the significant role played by macroeconomic, institutional, social, and government policy-related factors in sustainable development. More importantly, our results provide novel and robust evidence that the diffusion of green technology and climate change adaptation positively affect green growth. The study's empirical outcomes are demonstrated to be robust to misspecification errors and statistically significant at traditional significance levels. These findings carry substantial policy implications for the development and implementation of strategies that promote climate change adaptation and green innovation. Consequently, policymakers should prioritize the integration of green technology and adaptive measures in their sustainable development agendas to foster a greener, more resilient future.

Maxwell's electric equation and Schrödinger quantum equation are used to find useful expressions for the probability of electrons existence and the electrons transport. The first expression which uses special relatively also shows that the probability of the electrons existence is higher for lower energy states compared to higher energy states where the probability is low. This means that electrons transport takes place from higher energy states to lower states. This conforms to the laws of chemistry where the atom tends to be stable by forcing electrons to occupy lower energy states. The second expression used the momentum velocity relation instead of special relatively. This expression shows also electrons transport from higher to lower states. It also shows that the probability of the electrons existence is higher for lower electrons density regions and lower for higher electrons density regions. This means that the electrons transport is from higher density regions to lower density regions. This conforms to the diffusion law.

Inverse problems of recovering surface fluxes on the boundary of a domain from pointwise observations are considered. Sharp conditions on the data ensuring existence and uniqueness of solutions in Sobolev classes are exposed. They are smoothness conditions on the data, geometric conditions on the location of measurement points, and the boundary of a domain. The proof relies on asymptotics of fundamental solutions to the corresponding elliptic problems and the Laplace transform. The problem is reduced to a linear algebraic system with a nondegerate matrix.

Among the various methods for collecting oil spills and oil products, including from the water surface, one of the most effective is the use of sorbents. In this work, three-component bio-based composite granular adsorbents were produced and studied for oil products pollution collection. A bio-based binder made of peat, devulcanised crumb rubber from used tyres, and part fly ash as cenospheres were used for absorbent production. The structure, surface morphology, porosity, mechanical properties, and sorption kinetics of the obtained samples were studied. Composite hydrophobicity and sorption capacity to oil products such as diesel fuel (DF) and motor oil (MO) were determined. The obtained pellets are characterised by a sufficiently pronounced ability to absorb oil products such as DF. As the amount of CR in the granules increases, the diesel absorption capacity increases significantly. The case of 30-70-0 is almost 3 times higher than the granules from homogenised peat. The increase in q is due to two factors: pronounced surface hydrophobicity of the samples (Θ = 152°) and a heterogeneous porous granule structure. The presence of the cenosphere in the biocomposite reduces its surface hydrophobicity while increasing the diesel absorption capacity. Relatively rapid realisation of the maximum saturation by the MO was noted. In common, the designed absorbent shows up to 0.7 g·g^-1 sorption capacity for MO and up to 1.55 g·g^-1 sorption capacity for diesel. A possible mechanism of DF absorption and the limiting stages of the process approximated for different kinetic models are discussed. The Weber-Morris diffusion model is used to primarily distinguish the limiting effect of external and internal diffusion of adsorbate on the absorption process

The electrical performance of the back-channel etched Indium–Gallium–Zinc–Oxide (IGZO) thin-film transistors (TFTs) with copper (Cu) source and drain (S/D) which are patterned by a selective etchant was investigated. The Cu S/D were fabricated on molybdenum (Mo) layer to prevent the Cu diffusion to the active layer (IGZO). We deposited the Cu layer using thermal evaporation and performed the selective wet etching of Cu using non-acidic special etchant without damaging the IGZO active layer. We fabricated the IGZO TFTs and compare the performance in terms of linear and saturation region mobility, threshold voltage and ON current (ION). The IGZO TFTs with Mo/Cu S/D exhibits good electrical properties as the linear region mobility is 12.3 cm2/V-s, saturation region mobility is 11 cm2/V-s, threshold voltage is 1.2 V and ION is 3.16 x 10-6 A. We patterned all the layers by photolithography process. Finally, we introduced SiO2-ESL layer to protect the device from the external influence. The results show that the prevention of Cu and introduced ESL layer enhances the electrical properties of IGZO TFTs.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

The known three-component reaction-diffusion system modeling competition and co-existence of different language speakers is under study. A modification of this system is proposed, which is examined by Lie symmetry method; furthermore exact solutions in the form of traveling fronts are constructed and their properties are identified. Plots of the traveling fronts are presented and the relevant interpretation describing the language shift occurred in Ukraine during the Soviet times is suggested

This paper reveals the physical properties of Jeffery nanofluid flow past a moving plate embedded in porous medium under the existence of radiation and thermal diffusion. The analysis is carried out in three cases of moving plate, namely stationary plate λ = 0, forth-moving plate λ = 1, back-moving plate λ = −1. Finite difference method is applied to solve the governing equations of the flow and pointed out the variations in velocity, temperature and concentration with the use of graphical presentations. The impact of several parameters on local skin friction, Nusselt number and Sherwood number is also noticed and discussed. Enhancement of velocity is observed under the impact of Jeffery parameter for the cases of stationary plate and back-moving plate, whereas reverse nature is found in the case of forth-moving plate. The velocity enhances as the values of porosity parameter increases for the case of stationary plate and forth-moving plate but a reverse nature is noticed in the case of back-moving plate.

Almost all modern inorganic light-emitting diode (LED) designs are based on double heterojunctions (DHJs) whose structure and current injection principle have remained essentially unchanged for decades. Although highly efficient devices based on the DHJ design have been developed and commercialized for energy-efficient general lighting, the conventional DHJ design requires burying the active region (AR) inside a pn-junction. This has hindered the development of emitters utilizing nanostructured ARs located close to device surfaces such as nanowires or surface quantum wells. Modern DHJ III-N LEDs also exhibit resistive losses which arise from the DHJ device geometry. The recently introduced diffusion-driven charge transport (DDCT) emitter design offers a novel way to transport charge carriers to unconventionally placed ARs. In a DDCT device, the AR is located apart from the pn-junction and the charge carriers are injected into the AR by bipolar diffusion. This device design allows the integration of surface ARs to semiconductor LEDs and offers a promising method to reduce resistive losses in high power devices. In this work, we present a review of the recent progress in gallium nitride (GaN) based DDCT devices, and an outlook of potential DDCT has for opto- and microelectronics.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Chemotherapy for lung cancer has made remarkable progress, and its selection has been subdivided by genetic analysis. Although response evaluation criteria in solid tumors (RECIST) is a simple and highly objective evaluation method, it has been pointed out that it has the disadvantage of not being able to accurately evaluate the therapeutic effect of molecularly targeted drugs and immune checkpoint inhibitors. The purpose of this study is to determine whether quantitative evaluation of DWIBS is useful in determining the effectiveness of treatment for lung cancer. There were 31 patients with lung cancer and 56 patterns were obtained. First, the determination of treatment effect (PD, SD, PR) based on RECIST was performed on CT. Second, tDV and ADC (median) were measured using BD score from DWI images taken at the same time, and the rate of change was calculated. Then, we compared and examined the correlation between RECIST and the rate of change in tDV. There were correlations between RECIST and the rate of change in tDV in PD and PR cases respectively. Compared RECIST on CT, DWIBS using BD score would be more accurate for response evaluation of treatment. There was a tendency that tDV decreased with increasing ADC values, but some of the cases had a dissociated response with increasing ADC values and increasing tDV. Thus, since the color display of ADC values allows us to infer their contents, it would be useful for the evaluation of cases such as dissociated response and pseudoprogression, which are suspected to be atypical responses that are difficult to evaluate with RECIST and other methods.

Chaotic theory is commonly being researched for application in image encryption scheme (IES). In this paper, a novel two-dimensional cross hyperchaotic Sine-modulation-Logistic map (2D-CHSLM) based on the famous Sine and Logistic maps. The hyperchaotic behaviors of 2D-CHSLM is testified with the help of their bifurcation diagrams, trajectory plots, Lyapunov exponents, sample entropy, C0 complexity, permutation entropy and 0-1 test. A new bit-level IES with traditional encryption structure is proposed utilizing 2D-CHSLM. The 2D-CHSLM-IES performs a 2D-CHSLM-based bit-level confusion using zig-zag transform and a 2D-CHSLM-based cross coupled diffusion operations for generating a highly secure cipher-image. Then the simulations and security analyses are further carried out with the help of key space, key sensitivity, histogram, correlation, information entropy, differential attack, noise and data loss attacks, prove that the security of the proposed 2D-CHSLM-IES

We present a modified characteristic finite element method that exhibits second-order spatial accuracy for solving convection-reaction-diffusion equations on surfaces. The temporal direction adopted backward-Euler method, while the spatial direction employed surface finite element method. In contrast to regular domains, it is observed that the point in the characteristic direction traverses the surface only once within a brief time. Thus, the good approximation of the solution in the characteristic direction holds significant importance for the numerical scheme. In this regard, Taylor expansion is employed to reconstruct the solution beyond the surface in the characteristic direction. The stability of our scheme is then proved. A comparison is made with an existing characteristic finite element method based on face mesh. Numerical examples are provided to validate the effectiveness of our proposed method.

In the paper, we develop some numerical schemes including finite difference scheme and finite volume scheme for the fractional Laplacian operator, and apply the resulted numerical schemes to solve some fractional diffusion equations. First, the fractional Laplacian operator can be characterized as the weak singular integral by a integral operator with zero boundary condition. Second, because of the solution of fractional diffusion equation is usually singular near the boundary, we apply finite difference scheme to discrete fractional Laplacian operator and fractional diffusion equation by fractional interpolation function. Moreover, it is find that the differential matrix of the above scheme is symmetric matrix, and strictly row-wise diagonally dominant in special fractional interpolation function. Third, we show finite volume scheme to discrete fractional diffusion equation by fractional interpolation function, and analyze the properties of differential matrix. Finally, the numerical experiments are given, and verify the correctness of theoretical results and the efficiency of the schemes.

Image synthesis poses a challenging problem that researchers in computer vision and machine learning have been grappling with for several decades. Numerous machine learning techniques have emerged and proven effective in generating high-fidelity artificial images. This study breaks new ground by exploring image synthesis through generative learning using the D-Wave 2000Q quantum annealer, marking the first attempt to address the issue of generative image synthesis on a Quantum Processing Unit (QPU). Alongside executing image synthesis on the quantum annealer, this research also compares its performance with existing classical models and delves into resolving the Generative Learning Trilemma.

This work investigates a new nanostructured gas-diffusion-layer (nano-GDL) to improve performance of air-cathode Single-Chamber-Microbial-Fuel-Cells (a-SCMFCs). The new nano-GDLs improves the direct oxygen-reduction-reaction by exploiting the best of nanofibers from electrospinning in terms of high surface ratio to volume and high porosity, and laser-based processing to promote adhesion. Nano-GDLs by electrospinning were fabricated directly collecting two nanofibers mats on the same carbon-based electrode, acting as the substrate. Each layer was designed with a specific function: water resistant, oxygen permeable polyvinylidene-difluoride (PVDF) nanofibers served as a barrier to prevent water-based electrolyte leakage, while an inner layer of cellulose nanofibers was added to promote oxygen diffusion towards the catalytic sites. The maximum current density obtained for a-SCMFCs with the new nano-GDLs is (132.2 ± 10.8) mA m^-2, and it doubles the current density obtained with standard PTFE-based GDL (58.5 ± 2.4 mA m^-2), used as reference material. The energy recovery (EF) factor, i.e. the ratio of the power output to the inner volume of the device, was then used to evaluate the overall performance of a-SCMFCs. a-SCMFCs with nano-GDL provided an EF value of 60.83 mJ m^-3: one order of magnitude higher than the value of 3.92 mJ m^-3 obtained with standard GDL

In a previous paper, we solved the partial differential equation of Mullins problem in the case of the evaporation-condensation in electronic devices and gave an exact solution relative to the geometric profile of the grain boundary grooving when materials are submitted to thermal and mechanical solicitation and fatigue effect. In this new research, new modelling of the grain groove profile was proposed and new analytical expressions of the groove profile, the derivative and the groove depth were obtained in the case of diffusion in thin polycrystalline films by the resolution of the fourth differential equation formulated by Mullins that supposed 〖y'〗^2≪1. The obtained analytical solution gave more accurate information on the geometric characteristics of the groove that were necessary to study the depth and the width of the groove. These new findings will open a new way to study with more accuracy the problem of the evaporation-condensation combined to the diffusion phenomenon on the material surfaces with the help of the analytical solutions.

The microstructure of oil pipeline steels is polycrystalline due to the presence of a complex grain boundary (GB) network in them. The performance of them when exposed to stresses in corrosive environments is largely dictated by the interplay between the hydrogen (H) diffusion, the dislocation slip, and their interactions with the GBs. However, the slip-GB interaction in the presence of H and the subsequent cracking along the GBs remains not fully understood up to date. It is challenging to simultaneously resolve the collective dislocation motions away from the GBs together with the H diffusion near the atomically structured GBs using single-scale techniques. To address this challenge, taking bcc iron as a model material, here we present a a concurrent atomistic-continuum (CAC) computational analysis of the interaction between dislocation slip and a H-charged GB. With the large number of dislocations-mediated plastic flow away from the GB together with the atomistic structure evolution at the GB being simultaneously retained, several main findings from our simulations are: (i) the large number of dislocation-mediated pileup-induced internal stress nearby the H-charged GB can be as high as 3GPa; (ii) the more dislocations accumulated nearby the GB, the slower H diffusion ahead of the slip-GB intersection; (iii) H atoms diffuse fast behind the pileup tip, get trapped within the GB, and diffuse slow ahead of the pileup tip; (iv) the local stresses nearby the pileup tip exhibits a strong heterogeneity along the dislocation line direction. This differs from the common wisdom in many existing 2D theories/models. The buildup of such a high local stress heterogeneity leads to inhomogeneous H diffusion within the GB plane. The CAC simulation-predicted local H diffusivity, Dpileup−tip, and local stresses, σ, nearby the GB are then correlated with each other and consolidated into a mechanics model by considering the dislocation pileup as an Eshelby inclusion. These findings will provide researchers with opportunities to: (a) characterize the coupled dynamics between plasticity, H diffusion, and crack initiation underlying the hydrogen-induced cracking (HIC); (b) develop mechanism-based constitutive rules to be used in diffusion-plasticity coupling models for understanding the interplay between mechanical and mass transport in materials at the continuum level; and (c) connect the atomistic deformation physics of polycrystalline materials with their overall performance in aqueous environments, which is currently difficult to achieve in laboratory experiments.

Abstract: The diffusion of competition under the coexistence of multi-generation products has become one of the important challenges faced by enterprises in their daily and sustainable operations. At the same time, the competition between different brands has intensified the difficulty and complexity of decision-making in the process of multi-generation product operation, Therefore, based on the Norton-Bass model diffusion process, this paper introduces two marketing variables, dynamic price and quality level, builds a multi-generation product diffusion model under the dual-brand competition, and analyzes the impact of the company's revenue on the launch time to market, pricing, quality or technical level. By using system dynamics (SD) method, From the perspective of strong brand and weak brand enterprises, the competition diffusion model is built and simulated. The simulation shows that: i) When enterprises have the same brand competitiveness, reducing the pricing level cannot obtain more revenue, but diminish the overall revenue of the industry; Raising the pricing level can get more revenue, but also improve the revenue of competitors. ii) When the competitive strength of enterprises is different, the strong brand tends to maintain a stable pricing on the basis of improving the quality level, or slightly raise the price. Weak brands tend to raise the pricing of new products significantly on the basis of improving the quality level. iii) The launch time to market decision of new product is influenced by the degree of product quality upgrade. Therefore, the frequency of releasing new products should trade-off against the degree of technological upgrading of product quality. This paper provides the theoretical basis and new insights for the new product launch and operation decision of enterprises.

In this study various samples were fabricated by increasing the amount of CNT from 0% to 5%. The bulk mechanical properties of the samples were measured using DMA. Alternatively, the local mechanical properties were assessed using nanoindentation technique. There is a clear trend that the behavior of the material is dependent of carbon fillers before, during and after percolation threshold. The bulk mechanical properties were reduced after the percolation threshold due to CNT agglomeration. Then the samples were exposed to acid solution for one week and one month. Regardless the amount of CNT in the matrix, there is always a gradient of properties from the skin to the core of the sample. There is a net reduction of in physical properties. However, the level of degradation was a dependent of the amount of CNT in the host polymer. At higher concentration the CNTs behave as a barrier. However due to the formation of porosity around the CNT agglomerates, the acid diffusion encounters preferential path ways. . Both techniques lead to the same observation..

In the present study, the problem of the sulfuric acid recycling from spent copper plating solution was solved using a hybrid membrane technology, including diffusion dialysis and electrodialysis. A real solution from the production of copper-coated steel wire, containing 1.45 mol/L of sulfuric acid, 0.67 mol/L of ferrous sulfate and 0.176 mol/L of copper sulfate was processed. Diffusion dialysis with anion-exchange membranes was used to separate sulfuric acid and salts of heavy metals. Then purified dilute sulfuric acid was concentrated by electrodialysis. Energy consumption for sulfuric acid electrodialysis concentration at a current density of 400 A/m2 was 162 W·h/mol with current efficiency 16 %. After processing according to the hybrid membrane scheme, the solution contained 1.13 mol/L sulfuric acid, 0.077 mol/L ferrous sulfate and 0.022 mol/L copper sulfate. The resulting acid solution with a small amount of ferrous sulfate and copper sulfate met the established requirements for a copper plating bath solution and can be reused in production.

Ion-exchange membranes (IEMs) are widely used in desalination, waste water treatment, food, energy production and other applications. There is a strong demand for cost-effective IEMs characterized by high selective transport of ions of a certain sign of charge. In this paper, we simulate the experimental results of V. Sarapulova et al. (IJMS 2021) on the modification of an inexpensive anion-exchange membrane (CJMA-7, Hefei Chemjoy Polymer Materials Co. Ltd., China) with a perfluorosulfonated ionomer (PFSI). The modification was made in several stages including keeping the membrane at a low temperature, applying a PFSI solution on its surface, and subsequent drying it at an elevated temperature. We apply the known microheterogeneous model with some new amendments to simulate each stage of the membrane modification. It has been shown that the PFSI film formed on the membrane-substrate does not affect significantly its properties due to the small thickness of the film (4 m) and similar properties of the film and substrate. The main effect is caused by the fact that PFSI material “clogs” the macropores of the CJMA-7 membrane, thereby blocking the transport of coions through the membrane. In this case, the membrane microporous gel phase, which has a high selectivity to counterions, remains the primary pathway for both counterions and coions. Due to the above modification of the CJMA-7 membrane, the coion (Na+) transport number in the membrane equilibrated with 1 M NaCl solution decreased from 0.11 to 0.03. Thus, the modified membrane becomes comparable in its transport characteristics with more expensive IEMs available on the market.

A harmful impact of climate change and global warming has concerned various sectors of the international community. Numerous energy policies aiming at climate change mitigation have been implemented on a national and global scale. Renewable Energy Technologies (RET) play a critical role in enhancing sustainable solutions that significantly limit greenhouse gases (GHG) emissions. Such innovative technologies can facilitate energy transition through providing e.g. energy security, sustainable development, or effective usage of indigenous resources. However, the commercialization of RET becomes extremely challenging. The barriers can be of a different nature, although in this study the focus has been put on socio-economic and regulatory issues. In fact, there is ample evidence that energy policies play a central role in supporting renewables adoption. It is also claimed that RET require the whole ecosystem to support their successful diffusion. In this study, we explore multifarious barriers for a widespread RET diffusion in two European Union countries: Finland and Poland, indicating the most common barriers existing in the literature as well as analyzing major bottlenecks in the viewpoint of renewable energy companies’ executives. We also present statistics of the most commonly used RET in these countries in order to express the diffusion issues more appropriately. The outcomes of this study provide useful insight for the researchers in the energy transition field as well as practical managerial and regulatory implications aimed at overcoming these challenges.

In clinical diagnostics and longitudinal studies, the reproducibility of MRI assessments is of high importance in order to detect pathological changes, but developments in MRI hard- and software often outrun extended periods of data acquisition and analysis. This could potentially introduce artefactual changes or mask pathological alterations. However, if and how changes of MRI hardware, scanning protocols or preprocessing software affect complex neuroimaging outcomes from e.g. diffusion weighted imaging (DWI) remains largely understudied. We therefore compared DWI outcomes and artefact severity of 121 healthy participants (age range 19-54 years) who underwent two matched DWI protocols (Siemens product and Center for Magnetic Resonance Research sequence) at two sites (Siemens 3T Magnetom Verio and Skyra^fit). After different preprocessing steps, fractional anisotropy (FA) and mean diffusivity (MD) maps,obtained by tensor fitting, were processed with tract-based spatial statistics (TBSS). Inter-scanner and inter-sequence variability of skeletonised FA values reached up to 5% and differed largely in magnitude and direction across the brain. Skeletonised MD values differed up to 14% between scanners. We here demonstrate that DTI outcome measures strongly depend on imaging site and software, and that these biases vary between brain regions. These regionally inhomogeneous biases may exceed and considerably confound physiological effects such as ageing, highlighting the need to harmonise data acquisition and analysis. Future studies thus need to implement novel strategies to augment neuroimaging data reliability and replicability.

The instability of traveling pulses in nonlinear diffusion problems is inspected on the example of Gunn domains in semiconductors. Mathematically the problem is reduced to the calculation of the "energy" of the ground state in Schrödinger equation with a complicated potential. A general method to obtain the bottom-part spectrum of such equations based on the approximation of the potential by square wells is proposed and applied. Possible generalization of the approach to other types of nonlinear diffusion equations is discussed.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

The Covid-19 has hit Italy in February 2020 after its outbreak in China at the beginning of January. But why Italy first among Western countries? What are the conditions that made Italy more vulnerable and the first target of such disease? What characteristics and what diffusion patterns could be highlighted and hypothesized, from the outbreak to the end of March 2020, after containment measures - including a national lock down – were introduced? In this paper we try to provide some answers to these questions, analyzing the issue from the medical, geographical and planning points of view. In particular, we started from a hypothesis of very similar economic, geographical, climatic and environmental conditions of the areas of Wuhan – in Hubei Province in China, the outbreak of the epidemics – and the Po Valley area – in Italy – where most cases and deaths were registered. Adopting an ecological approach, we compared the spatial distribution and pattern of Covid-19-related mortality in Italy with several geographical, environmental and socio-economic variables at Provincial level, analyzing them by means of spatial analytical techniques as LISA – Local Indicators of Spatial Association. Possible evidence relating Covid-19 cases and Nitrogen-related pollutants and land take arise, particularly in the Po Valley area.

The diffusion coefficients of ions are measured in a microchip filled with a cationic charged 3D hydrogel in order to study the effect of cationic charged 3D hydrogel on the diffusivity of ions. In this study, poly-diallyl-dimethyl-ammoniumchloride (poly-DADMAC) is used to produce a 3D hydrogel. Four different fluorophores are used in the 3D hydrogel rhodamine 6G, rhodamine-BSA, fluorescein isothio-cyanate (FITC) and FITC-BSA. The rhodamine 6G and rhodamine-BSA are positively charged (cations), while fluorescein isothio-cyanate (FITC) and FITC-BSA are negatively charged (anions). Two widely used techniques which are short time diffusivity measurement technique and long time diffusivity measurement techniques are used to measure the diffusion coefficients. For the short time measurement, Fluorescence recovery after photo-bleaching (FRAP) is used by a 3D confocal microscope. For the long time measurement, fluorescence images are taken for 11 days to observe a pure diffusivity without any convective movement. As a result, the diffusivity of the cations was found to be lower than that of the anions in the cationic charged hydrogel.

This paper questions the potential shift of reproduction towards assisted reproductive technologies due to benefits provided by genetic manipulation of embryos. In order to examine the viability of such a shift and its implications from a regulatory perspective, we relied on two panels of experts from Israel and Spain, using the Delphi method and a series of in-depth interviews. We anticipate, at a first stage, a continuous-steady growth in the use of IVF, supplemented by preimplantation genetic diagnosis and the introduction of CRISPR/Cas. At a second stage, attracting a growing share of fertile people would require developments in genomics. While it is unclear whether these developments will fully materialize, they could be replaced by technoscientific imaginaries generating perceived benefits. We conclude that the regulation of reproductive genetics is becoming more critical and complex. The aim should be to ensure good practices and equity, while providing more information to the public. A broad and inclusive societal debate may overcome the difficulty of drawing a clear line between medical uses and non-medical uses of genetic selection and engineering and may contribute to finding the right balance between allowing autonomous decisions of patients and protecting the public interest.

The microstructures and mechanical properties of the hot-rolled Fe-6.5wt.%Si sheet are analyzed. The microstructure of the hot-rolled sheet is layered along the thickness direction. The surface exhibits fine and equiaxed grains, whereas the center part shows coarse and elongated grains with a <101> fiber texture along the rolling direction. Serrated flow behavior is observed during tensile deformation of both the hot-rolled sheet and its center samples at 350 °C; thus, the serrated flow of the hot-rolled sheet is mainly attributed to the serration of the center part. The analyses of dislocation configurations, ordered structures, and crystal orientation show that the serrated flow behavior results from the interaction of solutes with mobile dislocations. Mobile dislocations are pinned by combining parallel forest dislocations with the pipe diffusion of solution atoms. This study provides a new perspective for the deformation mechanism of the Fe-6.5wt.%Si alloy.

Using co-precipitation to synthesize (CeO2)0.95(Y2O3)0.05 (YDC) and solid reaction method to synthesize (CeO2)0.75(ZrO2)0.25 (ZDC), and the characterization for both crystal structure and micro-structure of the two materials was conducted with X-ray diffraction (XRD) and scanning electron microscope (SEM) methods. Prepare the YDC and ZDC based limited current O2 sensor by employing platinum pasting bonding method. Sensing characteristics of the sensor were obtained at different conditions and study on the impact of temperature, O2 concentration as well as water vapor pressure on the sensing characteristics had been conducted. XRD results show that the phase structure of both YDC and ZDC is cubic phase. SEM results show that both YDC and ZDC layers are dense layers, which are then qualified to be the composition materials of the sensor. This limited current O2 sensor shows good sensing performance and conforms to the Knudsen model. Log(IL•T) depends linearly on 1000/T with R2 of 0.9904, IL depends linearly on x(O2) with R2 of 0.9726 and sensing characteristics are not affected by p(H2O).

Alternative fuel vehicles, such as battery electric vehicles and hydrogen fuel cell vehicles, support the imperative to decarbonise the transport sector, but are not yet at a stage in their development where they can successfully compete with conventional fuel vehicles. This paper examines the influence of knowledge and persuasion on the decision to adopt or reject alternative fuel vehicles, underpinned by Rogers’ Diffusion of Innovations theory. A household questionnaire survey was undertaken with respondents in the Sutton Coldfield suburb of the United Kingdom city of Birmingham. This suburb was previously identified as having a strong spatial cluster of potential early adopters of alternative fuel vehicles. The results confirm that among respondents the knowledge of alternative fuel vehicles was limited and perceptions have led to the development of negative attitudes towards them. The reasons largely relate to three problems: purchase price, limited range, and poor infrastructure availability. The majority of respondents have passively rejected alternative fuel vehicles, such that they have never given consideration to adoption. This confirms that a concerted effort is required to inform the general public about alternative fuel vehicles.

Complex and real valued exact solutions to some reaction-diffusion equations are suggested by using homogeneous balance and Sine-Gordon equation expansion method. The predicted solution of finite series of some hyperbolic functions are determined by using some relations between the hyperbolic functions and trigonometric functions based on Sine-Gordon equation and traveling wave transform. The Newel-Whitehead-Segel and Zeldovich equations are solved explicitly. Some real valued solutions are depicted for some particular choice of parameters.

Tissue-like phantoms are widely used as a model for mimicking the optical properties of live tissue. This paper presents the results of a diffusion reflection method as well as fluorescence lifetime imaging microscopy measurements of fluorescein-conjugated gold nanorods in solution as well as inserted in solid tissue-imitating phantoms. A lack of consistency between the fluorescence lifetime results of the solutions and the phantoms raises a question about the ability of tissue-like phantoms to maintain the optical properties of inserted contrast agents.

Obesity in adolescents combined with the increased exposure time to electronic devices, enhances a sedentary lifestyle and is linked to the risk of developing musculoskeletal injuries. The aim of this study was to identify possible correlations between anthropometric characteristics, body composition, exposure time to electronic devices or screen time (ST) and physical activity (PA) level along with muscle power and dynamic knee valgus (DKV) in young athletes to avoid future injuries. A total of 125 adolescent basketball athletes (66.4% boys), 12 to 17 years old (13.94±1.58 years) participated. Anthropometric and demographic characteristics were recorded. PA level was assessed through IPAQ and ST through a single question from the HELENA study. The Counter Movement Jump test was used for the evaluation of the lower limb muscle power, while the Single Leg Drop Jump test was used for the evaluation of the dynamic knee valgus via two-dimensional (2D) kinematic analysis. The Pearson index showed a statistically significant positive correlation between muscle power and height (r=0.788, p<0.001), while the Spearman index showed a smaller but equally statistically significant positive correlation with BMI (rs =0.651, p<0.001) and age (rs=0.579, p<0.001). The ST (rs= -0.194, p=0.03) showed a weak negative correlation with DKV, while PA (r=0.85, p<0.001) showed a high, statistically significant, positive correlation. The anthropometric characteristics of adolescent athletes can determine their ability to produce muscle power. A high level of physical activity could play a key role in compensating and thus reducing the negative effects of high exposure to screen time on the dynamic knee valgus

Metal-organic frameworks (MOFs) represent the largest class of materials among the crystalline porous materials ever developed and have attracted attention as core materials for separation technology. Their extremely uniform pore aperture and nearly unlimited structural and chemical characteristics have attracted great interest and promise in applying MOFs to adsorptive and membrane–based separations. This paper reviews the recent research and development of MOF membranes for gas separation. Strategies for polycrystalline membranes and mixed matrix membranes are discussed, with a focus on separation systems involving hydrocarbon separation and CO2 capture. Challenges and opportunities for the industrial deployment of MOF membranes are also be discussed, providing guidance for the design and fabrication of future high-performance membranes. The contributions of the underlying mechanism to separation performances, and the adopted strategies and membrane processing technologies for breaking the selectivity/permeability trade–off are discussed.

A new three-dimensional numerical model of a polymer electrolyte fuel cell (PEFC) with a single straight channel has been developed to primarily investigate the important impact of the double-sided microporous layer (MPL) coating on the overall performance of the fuel cell and the distribution of the current and the oxygen concentration within the cathode gas diffusion layers (GDLs). Realistic experimentally estimated interfacial contact resistance values between the gas diffusion layer and each of the bipolar plates and the catalyst layer values were incorporated into the model, and parametric studies were performed. The results showed that the double-sided MPL coating could significantly improve the fuel cell performance by up to 30%. Also, it was shown that the neglect of the contact resistance between the MPL and the catalyst layer could overestimate the fuel cell performance by up to 6%. In addition, the results showed that the fuel cell performance and the distribution of the current and oxygen are more sensitive to the porosity of the MPL facing the bipolar plate than the porosity of the MPL facing the catalyst layer. All the above results are presented and critically discussed in detail.

Increased proliferation of IT services in all sectors has reinforced the adoption and diffusion across all levels of education and training institutions. However, lack of awareness of and knowledge about the key challenges and opportunities of elearning, seem to allude policymakers, resulting in low adoption or increased failure rate of many e-learning projects. Our study tries to address this problem through a review of relevant literature in e-learning. Our goal was to draw from the existing literature, insights into the opportunities and challenges of e-learning diffusion, and the current state-of-research in the field. To do this, we employed a systematic review of literature on some of the salient opportunities and challenges of e-learning innovation for educational institutions. These results aimed to inform policymakers and suggest some interesting issues to advance the research and adoption and diffusion of e-learning. Moreover, the bibliometric analysis shows that the field is experiencing high research attraction among scholars. However, several research areas in the field witnessed relatively low research paucity. Based on these findings, we discussed topics for possible future research.

In the present study, a mathematical model of non-steady partial differential equation from the process of oxygen mass transport in the human pulmonary circulation is proposed. Mathematical modelling of this kind of problems lead to a non-steady partial differential equation and for its numerical simulation, we have used finite differences. The aim of the process is the exact numerical analysis of the study, wherein consistency, stability and convergence is proposed. The necessity of doing the process is that, we would like to increase the order of numerical solution to a higher order scheme. An increment in the order of numerical solution makes the numerical simulation more accurate, also makes the numerical simulation being more complicated. In addition, the process of numerical analysis of the study in this order of solution needs more research work.

A new model for risk assessment of urban rainstorm disasters, based on information diffusion method and variable fuzzy sets (IDM-VFS) was proposed. In addition, an integrated index system of urban rainstorm risk was established. In the proposed model, IDM was employed to calculate the classification standards of urban rainstorm risk levels, then the VFS was adopted to assess the dangerousness, sensitivity, vulnerability and comprehensive risk of urban rainstorm disasters. In the present study, the urban rainstorm risk of Jiangsu province was evaluated with the proposed model. The results show that Wuxi, Changzhou, Nanjing and Suzhou have higher dangerousness, due to sustained rainfall and strong rainfall intensity in short duration; Wuxi, Changzhou and Nanjing have higher sensitivity because of lower disaster resistance ability; and Wuxi and Suzhou have higher vulnerability because these cities have higher potential losses in face of urban rainstorm disasters. The comprehensive risk zoning map of urban rainstorm shows apparent regional characteristics: the northwestern cities have lower risk than the southern cities. Moreover, most cities of the Jiangsu province are of the moderate urban rainstorm risk level. The results are consistent with the actual situation of Jiangsu province, and the study can provide some decision-making references for the urban rainstorm management.

In this paper, a local meshless method (LMM) based on radial basis functions (RBFs) is utilized for the numerical solution of various types of PDEs, due to the flexibility with respect to geometry and high order of convergence rate. In case of global meshless methods, the two major deficiencies are the computational cost and the optimum value of shape parameter. Therefore, research is currently focus towards localized radial basis function approximations, as the local meshless method is proposed here. The local meshless procedures is used for spatial discretization whereas for temporal discretization different time integrators are employed. The proposed local meshless method is testified in terms of efficiency, accuracy and ease of implementation using regular and irregular domains.

Many empirical and theoretical studies indicate that Brownian motion and diffusion models as its mean field counterpart provide appropriate modelling techniques for individual insect movement. However, this traditional approach has been challenged and conflicting evidence suggests that an alternative movement pattern such as Lévy walks can provide a better description. Lévy walks differ from Brownian motion since they allow for a higher frequency of large steps, resulting in a faster movement. Identification of the ‘correct’ movement model that would consistently provide the best fit for movement data is challenging and has become a highly controversial issue. In this paper, we show that this controversy may be superficial rather than real if the issue is considered in the context of trapping or, more generally, survival probabilities. In particular, we show that almost identical trap counts are reproduced for inherently different movement models (such as the Brownian motion and the Lévy walk) under certain conditions of equivalence. This apparently suggests that the whole ‘Levy or diffusion’ debate is rather senseless unless it is placed into a specific ecological context, e.g. pest monitoring programmes.

We propose a wave-like design on the surface of cathode channels (wave form cathode channels) to improve oxidant delivery to gas diffusion layers (GDLs) [1-2]. We performed experiments using PEMFCs combined with wave form surface design on cathodes. We varied the factors of the distance between wave-bumps (the Adhesive distance, AD), and the size of the wave-bumps (the Expansion ratio, ER). The ADs are 3, 4, and 5 times the size of the half-circle bump’s radius, and the ERs are 1/1.5, 1/2, and 1/3 times the channel’s height. We evaluated the performances of the fuel cells, and compared the current-voltage (I-V) relations. For comparison, we prepared PEMFCs with conventional flat-surfaced oxygen channels. Our aim in this work is to identify fuel cell operation by modifying the surface design of channels, and ultimately to find the optimal design of cathode channels that will maximize fuel cell performance.

A two-layer Fe-Cr-Al-Zr surface alloy was synthesized on a zirconium substrate by magnetron sputtering and subsequent low-energy high-current electron-beam (LEHCEB) processing. Thicknesses of the top Fe69Cr20Al11 (at.%) relatively large-grained (~1 µm) and transition Fe-Zr Cr-Al amorphous layers were about 0.7 and 0.6 µm, respectively. In turn, the amorphous layer consisted of two Fe64–54Zr8–22Cr21–17Al8–7 and Fe40–16Zr42–78Cr12–4Al6–2 (at.%) sublayers, differing in both zirconium and iron concentrations in wide ranges, which were separated by another nanocrystalline interlayer. The Fe-Cr-Al-Zr surface alloy serve as a diffusion barrier, preventing interaction of the zirconium substrate with oxygen from an environment. It was thermally stable up to ≈1173 K.

In this paper, Akbari-Ganji's and Taylor series methods are applied to find analytical solutions to nonlinear differential equations that arise in an immobilized-cell photobioreactor. Approximate analytical expressions for substrate and product concentrations and both liquid and gas phases for various parameter values are derived using both methods. Efficiency, accuracy, and convergence of the two methods relative to highly accurate numerical methods are investigated to establish reliable profiles of these two methods for solving general nonlinear equations that model various physical phenomena. Numerical simulations are presented to validate the theoretical investigations.

The main objective of this work was to evaluate the application of individual and ensemble machine learning models to classify malignant and benign breast masses using features from two-dimensional (2D) correlated spectroscopy spectra extracted from five-dimensional Echo Planar-Correlated Spectroscopic Imaging (5D EP-COSI) and Diffusion-weighted imaging (DWI). Twenty-four different metabolite and lipid ratios with respect to 2D diagonal peaks at 1.4ppm and 5.4ppm, and water from one-dimensional non-water-suppressed (NWS) spectra were used as the features. Additionally, water fraction, fat fraction and water-to-fat ratios from NWS spectra and apparent diffusion coefficients (ADC) from DWI were included. Nine most important features were identified using recursive feature elimination. XGBoost (AUC:93.0%, Accuracy:85.7%, F1-score:87.6%), GradientBoost (AUC:94.4%, Accuracy:87.0%, F1-score:89.4%), CatBoost (AUC:95.2%, Accuracy:86.9%, F1-score:88.4%) and RandomForest (AUC:92.2%, Accuracy:85.3%, F1-score:87.6%) were the best performing models. While the conventional biomarkers like choline, myo-Inositol, and glycine were statistically significant predictors, the key features contributing to the classification were ADC, 2D diagonal peaks at 0.9ppm, 2.1ppm and 2.3ppm, cross peaks between 1.4 and 0.9ppm, 4.3 and 4.1ppm, 2.1 and 1.4ppm and the triglyceryl-fat cross peak. The results highlight the contribution of the 2D spectral peaks to the model, and they demonstrate the potential of 5D EP-COSI for early breast cancer detection.