Analysis of 1382 measures of battery State of Health (SoH) from 283 Nissan Leafs (“Leaf/s”), manufactured between 2011 and 2017, has detected a faster rate of decline in this measure of energy-holding capacity for 30 kWh variants. At two years of age, the mean rate of decline of SoH of 30 kWh Leafs was 9.9% per annum (95% uncertainty interval of 8.7% to 11.1%; n = 82). This was around three times the rate of decline of 24 kWh Leafs which at two years averaged 3.1% per annum (95% uncertainty interval of 2.9% to 3.3%; n = 201). For both variants there was evidence for an increasing rate of decline as they aged, although this was much more pronounced in the 30 kWh Leafs. Higher use of rapid DC charging was associated with a small decrease in SoH. Additionally, while 24 kWh cars with greater distances travelled showed a higher SoH, in 30 kWh cars there was a reduction in SoH observed in cars that had travelled further. The 30 kWh Leafs sourced from United Kingdom showed slower initial decline than those from Japan, but the rate of decline was similar at two years of age. Improvements in the battery health diagnostics, continuous monitoring of battery temperatures and state of charge, and verification of a fundamental model of battery health are needed before causes and remedies for the observed decline can be pinpointed. If the high rate of decline in battery capacity that we observed in the first 2.3 years of a 30 kWh Leaf’s lifetime were to continue, the financial and environmental benefits of this model may be significantly eroded. Despite 30 kWh Leafs accounting for only 14% of all light battery electric vehicles registered for use on New Zealand roads at the end of February 2018, there is also the potential for the relatively poor performance of this specific model to undermine electric vehicle uptake more generally unless remedies can be found.

Mass transfer restrictions of scaffolds are currently hindering the development of three-dimensional (3D), clinically viable, and tissue engineered constructs. For this situation, a 3D poly(lactide-co-glycolide)/hydroxyapatite porous scaffold, which was much favorable for transfer of nutrients to and waste products from the cells in the pores, was developed in this study. The 3D scaffold had an innovative structure, including macropores with diameters of 300−450 μm for cell ingrowth and microchannels with diameters of 2−4 μm for nutrition and waste exchange. The mechanical strength in wet state was strong enough to offer the structural support. The typical structure was more beneficial for the attachment, proliferation, and differentiation of rabbit bone marrow mesenchymal stem cells (rBMSCs). The alkaline phosphatase (ALP) activity and calcium (Ca) deposition were evaluated on the differentiation of rBMSCs, and the results indicated that the microchannel structure was very favorable for differentiating rBMSCs into maturing osteoblasts. For repairing rabbit radius defects in vivo, there was rapid healing in the defects treated with the 3D porous scaffold with microchannels, where the bridging by a large bony callus was observed at 12 weeks post-surgery. Based on the results, the 3D porous scaffold with microchannels was a promising candidate for bone defect repair.

The cell case temperature versus time profiles of a multistage fast charging technique (4C-1C-CV)/fast discharge (4C) in a 2.3 Ah cylindrical lithium-ion cell are analyzed using a 1D thermal model. Heat generation is dominated by the irreversible component associated to cell overpotential, although evidences of the reversible component are also observed, associated to the heat related to entropy from the electrode reactions. The final charging stages (i.e., 1C-CV) significantly reduce heat generation and cell temperature during charge, resulting in a thermally safe charging protocol. Cell heat capacity was determined from cell specific heats and cell materials thickness. The 1D model adjustment of the experimental data during the 2 min. resting period between discharge and charge allowed us to calculate both the time constant of the relaxation process and the cell thermal resistance. The obtained values of these thermal parameters used in the proposed model are almost equal to those found in the literature for the same cell model, which suggests that the proposed model is suitable for its implementation in thermal management systems.

In this study the impact of terrorist attacks on exchange rate is estimated. Particularly, the study focuses on Turkish terrorist attacks and its implication on Turkish lira versus pound sterling exchange rate. In order, to find the causal effect the study employed Autoregressive distributive lag (ARDL) bound testing approach as an estimation technique. Accordingly, the analysis reveals that terrorist attack has a negative impact on the exchange rate in both short and long-run. However, the negative effect of terrorism tends to be small in both the short-run and long-run. More precisely, terrorist attack depreciates the exchange rate between Turkish lira and pound sterling by approximately 0.00072 in the next trading day. The long-term effect also shows that terrorist attack depreciates the exchange rate on average by 0.00212.

Despite the use of commercial forest carbon protocols (CFCPs) for more than two decades, claiming ~566 MMtCO₂e and a market value of ~USD $15.7 billion, comparative analysis of CFCP methodology and offset results is limited. In this study, five widely used biometric-based CFCPs are characterized, and common characteristics and differences are identified. CFCP claims of net forest carbon sequestration are compared with results of directly measured CO₂ by eddy covariance, a meteorological method integrating gross vertical fluxes of forest and soil carbon, and the only alternative non-biometric source of net forest carbon sequestration data available. We show here that CFCPs share a structural feature delimiting forest carbon values by zero-threshold carbon accounting (gC m^-2 ≤ 0), a pattern opposite to natural emissions of forest CO₂ exchange based on direct measurement and a fundamental biological constraint on net forest carbon storage (i.e., soil efflux, ecosystem respiration). Exclusion of forest CO₂ sources to the atmosphere precludes net carbon accounting, resulting in unavoidable over-crediting of CFCP project offsets. CFCP carbon results are significantly different from global forest CO₂ net ecosystem exchange population results (FluxNet2015 gC m^-2) at the 95% to 99.99% confidence levels, inferring an annual median error of ~247% (gC m^-2), consistent with over-crediting. Direct CO₂ measurement provides an urgently needed alternative method for commercial forest carbon products that has the potential to harmonize global markets and catalyze the role of forests in managing climate change through nature-based solutions.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

In this work commercial 18650 lithium-ion cells with LiMn₂O₄, LiFePO₄ and Li(Ni_0.33Mn_0.33Co_0.33)O₂ cathodes were exposed to external heating in an Accelerating Rate Calorimeter (es-ARC, THT Company) to investigate the thermal behavior under abuse conditions. New procedures for measuring external and internal pressure change of cells were developed. The external pressure was measured utilizing a gas-tight cylinder inside the calorimeter chamber in order to detect venting of the cells. For internal pressure measurements, a pressure line connected to a pressure transducer was directly inserted into the cell. During the thermal runaway experiments, three stages (low rate, medium rate and high rate reaction) have been observed. Both pressure and temperature change indicated different stages of exothermic reactions, which produced gases or/and heat. The onset temperature of thermal runaway was estimated according to temperature and pressure changes. Moreover, the different activation energies for the exothermic reactions could be derived from Arrhenius plots.

The rationalization of single molecule magnets’ (SMMs) magnetic properties by quantum mechanical approaches represents a major task in the field of the Molecular Magnetism. The fundamental interpretative key of molecular magnetism is the phenomenological Spin Hamiltonian and the understanding of the role of its different terms by electronic structure calculations is expected to steer the rational design of new and more performing SMMs. This paper deals with the ab initio calculation of isotropic and anisotropic exchange contributions in the Fe(III) dimer [Fe₂(OCH₃)₂(dbm)₄]. This system represents the building block of one of the most studied Single Molecule Magnets ([Fe₄RC(CH₂O)₃)₂(dpm)₆] where R can be an aliphatic chain or a phenyl group just to name the most common functionalization groups) and its relatively reduced size allows the use of a high computational level of theory. Calculations were performed using CASSCF and NEVPT2 approaches on the X-ray geometry as assessment of the computational protocol, which has then be used to evinced the importance of the outer coordination shell nature through organic ligand modelization. Magneto-structural correlations as function of internal degrees of freedom for isotropic and anisotropic exchange contributions are also presented, outlining for the first time the extremely rapidly changing nature of the anisotropic exchange coupling.

This paper investigates the impact of price and real exchange rate volatility on Foreign Direct Investment (FDI) inflows in a panel of 10 Latin American and Caribbean countries, observed between 1990 and 2012. Both price and exchange rate volatility series are estimated through the Generalized Autoregressive Conditional Heteroscedasticity model (GARCH). Our results, obtained employing the Fixed Effects estimator, confirm the theory of hysteresis and option value, in so far it is found a statistically significant negative effect of exchange rate volatility on FDI. Price volatility, instead, turns out to be positive but insignificant. Moreover, we show that human capital and trade openness are key for attracting foreign capital. From the policy perspective, our analysis suggests the importance of stabilization policies as well as the one of government credibility in promoting trade openness and human capital formation.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Dry intrusion is an important mid-latitude atmosphere phenomenon within the upper troposphere and lower stratosphere. It is always found to be related to the cyclogenesis, rainstorm, as well as convection generation and precipitation enhancement. Since the atmosphere environment for any of these above-mentioned weather is terribly complicated, those preexisting popular schemes which takes no account of water vapor may not suitable for detecting the dry intrusion related to these weathers. With regard to the merits and demerits of the current preexisting schemes, a new scheme based on Fengyun-2E geo-stationary satellite data is presented in this study to detect the atmospheric dry intrusion. The scheme is set up based on the statistical relationship between water vapor at high level troposphere, the general moist potential vorticity, ozone concentration and upper-level jet. After using the total amount of ozone and ozone profile operational products retrieved by Fengyun-3 Polar Orbiting Meteorological Satellites and the potential vorticity calculated by ECMWF Interim data for validation, this scheme is applied to analyze two typical middle-latitude weather processes. One is the famous Beijing extreme rainfall of 21 July 2012 and the other is a hailstorm occurred on the eastern China during March 19, 2014. A good application effect in both cases suggests that our new method of detecting dry intrusion is feasible and can be helpful in middle-latitude disastrous weather monitoring and forecasting.

This work shows the physicochemical and mineralogical characterization of diatomites form the Hidalgo and Jalisco States, Mexico. In the case of the mineral from Hidalgo State, this has the following chemical composition; 70.0 % wt. SiO₂, 11.63 wt. % Al₂O₃, 1.95 wt. % FeO, 1.79 wt. % MgO, 2.41 wt. % K₂O, 0.85 wt. % CaO and 6.10 wt. % Na₂O. On the other hand, the mineral from Jalisco has the following chemical composition; 93.58 wt. % SiO₂, 3.03 wt. % Al₂O₃, 1.81 wt. % FeO, 0.40 wt. % MgO, 0.92 wt. % K₂O, 0.11 wt. % CaO and 0.24 wt. % Na₂O. For recovery of metals, both minerals got arsenic, silver, lead and nickel recoveries upper to 95 % and lower to 10 % for chromium. According to efficiency of interchange, the mineral from Hidalgo is slightly higher in the case of arsenic, lead and silver; while for nickel and particularly chromium (VI) the efficiency is higher for the mineral from Jalisco.

Batteries are called to be part of the electricity grid by providing ancillary services. Area regulation services seem to provide substantial revenues and profit. But Li-ion batteries are still too expensive to enter widely into this market. On the other hand, electric vehicle batteries are considered inappropriate for traction purposes when they reached a state of health of 80%. The reuse of these batteries offers affordable batteries for second life stationary applications. This study analyzes how batteries may provide services to a gas turbine cogeneration power plant and how long these batteries may last under different loads.

Considering the safety issues of Li ion batteries, all-solid-state polymer electrolyte has been one of the promising solutions. In this point, achieving a Li ion conductivity in the solid state electrolytes comparable to liquid electrolytes (>1 mS/cm) is particularly challenging. Employment of polyethylene oxide (PEO) solid electrolyte has not been not enough in this point due to high crystallinity. In this study, hybrid solid electrolyte (HSE) systems are designed with Li_1.3Al_0.3Ti_0.7(PO₄)₃(LATP), PEO and Lithium hexafluorophosphate (LiPF₆) or Lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). Hybrid solid cathode (HSC) is also designed using LATP, PEO and lithium cobalt oxide (LiCoO₂, LCO)—lithium manganese oxide (LiMn₂O₄, LMO). The designed HSE system displays 3.0 × 10⁻⁴ S/cm (55 ℃) and 1.8 × 10⁻³ S/cm (23 ℃) with an electrochemical stability as of 6.0 V without any separation layer introduction. Li metal (anode)/HSE/HSC cell in this study displays initial charge capacity as of 123.4/102.7 mAh/g (55 ℃) and 73/57 mAh/g (25 °C). To these systems, Succinonitrile (SN) has been incorporated as a plasticizer for practical secondary Li ion battery system development to enhance ionic conductivity. The incorporated SN effectively increases the ionic conductivity without any leakage and short-circuits even under broken cell condition. The developed system also overcomes the typical disadvantages of internal resistance induced by Ti ion reduction. In this study, optimized ionic conductivity and low internal resistance inside the Li ion battery cell have been obtained, which suggests a new possibility in the secondary Li ion battery development.

This paper uses panel data to find the determinants of tracking errors in exchange traded funds (ETFs) in the Hong Kong stock market. A comparison of tracking errors between physical and synthetic ETFs also indicates that the synthetic ETFs have higher tracking errors. The magnitude of tracking errors is found to be negatively related to size but positively related to dividend yield, trading volumes of funds, and market risk. However, this study also finds that expense ratio has a negative impact on tracking error, which is not consistent with previous studies, and which this paper addresses.

Bio-molecular reagents like antibodies required in experimental biology are expensive and their effectiveness, among other things, is critical to the success of the experiment. Although such resources are sometimes donated by one investigator to another through personal communication between the two, there is no previous study to our knowledge on the extent of such donations, nor a central platform that directs resource seekers to donors. In this paper, we describe, to our knowledge, a first attempt at building a web-portal titled Bio-Resource Exchange that attempts to bridge this gap between resource seekers and donors in the domain of experimental biology. Users on this portal can request for or donate antibodies, cell-lines and DNA Constructs. This resource could also serve as a crowd-sourced database of resources for experimental biology. Further, in order to index donations outside of our portal, we mined scientific articles to find instances of donations of antibodies and attempted to extract information about these donations at the finest granularity. Specifically, we extracted the name of the donor, his/her affiliation and the name of the antibody for every donation by parsing the acknowledgements sections of articles. To extract annotations at this level, we propose two approaches – a rule based algorithm and a bootstrapped relation learning algorithm. The algorithms extracted donor names, affiliations and antibody names with average accuracies of 57% and 62% respectively. We also created a dataset of 50 expert-annotated acknowledgements sections that will serve as a gold standard dataset to evaluate extraction algorithms in the future. Contact: madhavi@pitt.edu, madhavi@cs.cmu.edu Database URL: http://tonks.dbmi.pitt.edu/brx Supplementary information: Supplementary data are available at Database online.

Plasma being the fourth and most abundant form of matter extensively exists in the universe in the inter-galactic regions. It provides an electrically neutral medium of unbound negative and positive charged particles, which has been produced by subjecting air and various other gaseous mixtures to strengthen the electromagnetic field and by heating compressed air or inert gasses for creating negative and positive charged particles known as ions. Nowadays, many researchers are paying attention to the formation of artificial Plasma and its potential benefits for mankind. The literature is sparsely populated with the applications of Plasma. This paper presents specific methods of generation and applications of Plasma, which benefits humankind in various fields, such as in electrical, mechanical, chemical and medical fields. These applications include hydrogen production from alcohol, copper bonding, semiconductor processing, surface treatment, Plasma polymerization, coating, Plasma display panels, antenna beam forming, nanotechnology, Plasma Torch, Plasma pencils, low-current non-thermal Plasmatron, treatment of prostate cancer, Plasma source ion implantation, cutting by Plasma, Plasma etching, pollution control, neutralization of liquid radioactive waste, etc. Resultantly, worth of Plasma technology in the medical industry is increasing exponentially that is closing the gap between its benefits and cost of equipment used for generating and controlling it.

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.

The Foreign Exchange rate is very much crucial for determining the economic health level of the country. The foreign exchange rate provides financial stability, enhances purchasing power and allows global trades. This rate usually fluctuates due to the market forces which control the supply and demand of the currency. Nominal and relative inflation and income level have a substantial effect on determining the exchange rates. Government measures, international situations, natural disasters or any unexpected situation like Covid-19, Rohingya crisis etc. can affect the exchange rates. Besides this, the interaction between the factors can create different reasoning to affect the market. This study tries to identify some factors with relevant examples.

The aim of this research work was to provide model for predicting stock volatility in Nigeria Stock market. To achieve this, monthly data for Nigerian stock exchange, Exchange rate, Share index and inflation rate was collected for a period of January 1990 to December 2016.The descriptive statistics revealed these variables to exhibit volatility as a characteristics of financial time –varying series. DCC Model was fitted, were the coefficients for all the parameters and that of the correlation-Targeting (rho_21) are both negative and positive and tend very close to 1 and -1, indicating that high persistence in the conditional variances. The Model DCC, satisfied the properties of a good model of conditional mean and variance of the confidential Interval (C.I) of 1 and -1, that is, the conditional variances are finites and their series are strictly stationary. This therefore implies that the Nigerian Stock Exchange, Exchange rate, share index and Inflation rate will experience a non-steady shock in the Stock market. However Each of these variables have different length of recovery (volatility half- life) ranging from 1.5month, 6.5months, 6months to 2,4months for stock exchange, exchange rate, share index and inflation rate respectively. By implication, the volatility of these variables had a long memory, persistence and mean-reverting.

Porous MnO/C microspheres have been successfully fabricated by a fast co-precipitation method in a T-shaped microchannel reactor. The structures, compositions and electrochemical performances of the obtained MnO/C microspheres are characterized by X-ray diffraction, emission scanning electron microscopy, transmission electron microscopy (HRTEM), Brunauer–Emmett–Teller analysis, charge-discharge testing, cyclic voltammograms, and electrochemical impedance spectra. Experimental results reveal that the as-prepared MnO/C, with a specific surface area of 96.66 m²·g^–1 and average pore size of 24.37 nm, exhibits excellent electrochemical performance, with a discharge capacity of 655.4 mAh·g^–1 after cycling 50 times at 1 C and capacities of 808.3, 743.7, 642.6, 450.1, and 803.1 mAh·g^–1 at 0.2, 0.5, 1, 2, and 0.2 C, respectively. Moreover, the controlled method of using a micro-channel reactor, which can produce larger specific surface area porous MnO/C with improved cycling performance by shortening lithium-ion diffusion distances, can be easily applied in real production on a large-scale.

The structural, electronic and magnetochemical properties of the star-shaped polyoxopalladate [Pd₁₅O₁₀(SeO₃)₁₀]¹⁰⁻ (POPd) and its lanthanide functionalized derivatives have been investigated on the basis of density functional theory followed by a ligand field analysis using the Radial Effective Charge (REC) model. Our study predicts that heteroPOPd is a robust cryptand that enforces D_5h symmetry around the encapsulated Ln³⁺ centers. This rigid coordination environment favors interesting potential magnetic behavior in the Er and Ho derivatives, which may be of interest for molecular spintronics and quantum computing applications.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

The production of lithium-ion battery cells is characterized by a high degree of complexit due to numerous cause-effect relationships between process characteristics. Knowledge about the multi-stage production is spread among several experts, rendering tasks such as failure analysis challenging. In this paper, a method is presented, which includes expert knowledge acquisition in production ramp-up by combining Failure Mode and Effects Analysis (FMEA) with a Bayesian Network. We show the effectiveness of this holistic method by building up a large scale, cross-process Bayesian Failure Network in lithium-ion battery production. Using this model, we are able to conduct root cause analyses as well as analyses of failure propagation. The former support operators in identifying root causes once a cell possesses a specific failure by calculating most-probable explanations matched to the individual battery cell data. The latter enable us to analyze propagation of failures and deviations in the production chain and thus provide support for placement of quality gates, leading to a significant reduction in scrap rate. Moreover, it gives an insight into which process steps are key drivers for which final product characteristics.

Stabilized un-doped Zinc Telluride (ZnTe) thin films were grown on glass substrates under vacuum using closed space sublimation (CSS) technique. A dilute copper nitrate solution (0.1/100 ml) was prepared for copper doping known as ion exchange process in the matrix of ZnTe thin film. The reproducible polycrystalline cubic structure of undoped and Cu doped ZnTe thin films with preferred orientation (111) was confirmed by X-rays diffraction (XRD) technique. Lattice parameter analyses verified the expansion of unit cell volume after incorporation of Cu species into ZnTe thin films samples. The micrographs of scanning electron microscopy (SEM) were used to measure the variation in crystal sizes of samples. The energy dispersive X-rays was used to validate the elemental composition of undoped and Cu-doped ZnTe thin films. The bandgap energy 2.24 eV of ZnTe thin film decreased after doping Cu to 2.20 eV may be due to the introduction of acceptors states near to valance band. Optical studies showed that refractive index was measured from 2.18 to 3.24 whereas thicknesses varied between 220 nm to 320 nm for un-doped and Cu doped ZnTe thin film respectively using Swanepoel model. The oxidation states of Zn⁺², Te⁺² and Cu⁺¹ through high resolution X-ray photoelectron spectroscopy (XPS) analyses was observed. The resistivity of thin films changed from ~10⁷ Ω-cm for undoped ZnTe to ~1 Ω-cm for Cu-doped ZnTe thin film, whereas p-type carrier concentration increased from to respectively. These results predicted that Cu-doped ZnTe thin film can be used as an ideal, efficient and stable intermediate layer between metallic and absorber back contact for the heterojunction thin film solar cell technology.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

Ag+ pollution is great of harm to the human body and the biology. Therefore, it is an urgent need to develop inexpensive and accurate detection methods. Herein, lignin-derived structural memory carbon nanodots (CSM-dots) with outstanding fluorescence property were fabricated via a green method, which reserve functional and structural units of the precursor molecules. The CSM-dots could specifically bind Ag+, accompanied with a remarkable fluorescence quenching response. This “turn-off” fluorescence behavior was used for Ag+ determination in a linear range of 5-290 μM with the detection limit as low as 500 nM. Furthermore, the finding showed that this sensing nano-platform was successfully used for Ag+ determination in real samples and intracellular imaging, showing great potential in biological and environmental monitoring applications.

This study aims to examines three elements shape leadership in Leader-Member Exchange (LMX) theory as a relationship and process. LMX quality is important for the company, because it relates to employee behavior and attitudes, including improving employee performance. The research method applied literature review using description logic and systematics. In this article the theory will be observed specially the effect of LMX on employee performance and antecedents of LMX. The results of the study found that the effect of LMX quality on performance is determined by the characteristics of the task as antecedent LMX in the company.

Despite a rapid rise in NBS development in recent years, the methods for evaluating NBS still have certain gaps. We propose an approach based on a combination of remote sensing data and meteorological variables to reconstruct the spatio-temporal variation of net ecosystem exchange from eddy-covariance stations. Lagrangian particle dispersion model was used for upscaling of satellite images and flux towers. We trained data-driven models based on kernel methods separately for each selected land cover class. The results suggest that the proposed approach to quantifying carbon exchange on a medium-to-large scale by blending eddy covariance flux data with moderate resolution satellite and weather data provides a set of key advantages over previously deployed methods: (1) scalability, achieved via the validation design based on a separate set of eddy covariance stations; (2) high spatial and temporal resolution due to use of the Landsat imagery; (3) robust and accurate predictions due to improved data quality control, advanced machine learning techniques, and rigorous validation. The machine learning models yielded high cross-validation results. Overall we present here globally scaled technology for the land sector based on high resolution remote sensing imagery, meteorological variables, and direct carbon flux measurements of eddy covariance flux stations.

Lithium batteries and an increasing focus on CO₂ reduction have become an integral part of daily life and business for many people. Boron and boron compounds have been widely studied together in the history and development of lithium batteries. With a broad examination of battery components and systems but a boron-centric approach to raw materials, this review seeks to summarize past and recent studies on the following: which boron compounds are studied in lithium battery, in which parts of lithium batteries, what improvements are offered for battery performance, and what improvement mechanisms can be explained. The uniqueness of boron and its extensive application beyond batteries contextualizes the interesting similarity with studies on batteries. The paper predominantly focuses on lithium-ion batteries (LIBs) but also mentions other lithium batteries. At the end, the article aims to predict prospective trends for future studies that may lead to the successful and extensive use of boron compounds on a commercial scale.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

Background: Tourism is one of the prominent industry that has a capability to generate handsome income for developed as well as developing countries. However, the study to investigate specifically the perception of local residents towards tourism is still lacking. The perception of the locals is important since it could determine the extent of their support for tourism development. Plus, previous research found that male residents are more support better towards the tourism development. Thus, this factor is adapted as well in this study to examine whether this gender may influence to the tourism industry. 2) Methods: This study used Structural Equation Modeling (SEM) technique for determining the structural estimates between constructs. 3) Results: The respondents agree that positive perception, negative perception and tourism impact has a significant impact on support for tourism development in which has been recognized as Social Exchange Theory model. Moreover, the finding also revealed that gender has a potential to moderates the causal effect of tourism impact on tourism development. 4) Conclusion: The resident understand the tourism sector could strengthen economic nation but they also want the natural resources should be protected.

Crystalline β-cobalt hydroxide (β-Co(OH)₂) of different morphologies have been successfully synthesized with the addition of sodium hydroxide to cobalt nitrate solution and aging in the mother liquor. The rate of NaOH addition, ranging from 0.1 mL/min to 10 mL/min, influences the surface morphology with the obtained storage capability of the respective electrode. Characterization of the β-Co(OH)₂ was fully developed, including X-ray diffraction, scanning and transmission electron microscopy, and BET analyses. At a lower rate of NaOH addition, particles are like platelets, while for a higher rate (≥2 mL/min) grains are fused together forming a larger crystallite size. This result is supported by the X-ray diffraction structural analysis, where the phase evolution of (002) plane becomes distinct for the higher rate of NaOH addition. Lithium cobalt oxide (LiCoO₂) was synthesized through oxidation from the as-prepared β-Co(OH)₂ and LiOH. The electrochemical performance of as obtained LiCoO₂ is investigated using charge-discharge and cyclic voltammetric studies. The precursor β-Co(OH)₂ prepared at a lower rate of 0.1 mL/min in LiCoO₂ demonstrated the best electrochemical performance of 155 mAh/g. After 50 cycles, the capacity retention rate was 67% compared with the first cycle. Finally, we have attempted to correlate the amount of the available OH^- ions with the formation of platelets and the discharge capacity. This work has developed a methodology for the synthesis of LiCoO₂ using β-Co(OH)₂ in a facile chemical solution process.

The separator membrane is an essential component of lithium-ion batteries, separating the anode and cathode and controlling the number and mobility of the lithium ions. Among the polymer matrices most investigated for battery separators are poly(vinylidene fluoride) (PVDF) and its copolymers poly(vinylidene fluoride-co-trifluoroethylene) (PVDF-TrFE), poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), and poly(vinylidene fluoride-cochlorotrifluoroethylene) (PVDF-CTFE), due to their excellent properties such as high polarity and the possibility of controlling the porosity of the materials through binary and ternary polymer/solvent systems, among others. This review presents the recent advances on battery separators based on poly(vinylidene fluoride) (PVDF) and its copolymers for lithium-ion batteries. It is divided in the following sections: single polymer and co-polymers, surface modification, composites and polymer blends. Further, a critical comparison between those membranes and other separator membranes is presented, as well as the future trends on this area.

In atomic GdFe$_2$ films capped by 4$d$ and 5$d$ transition metals, we show that skyrmions with diameters smaller than 12 nm can emerge. The Dzyaloshinskii--Moriya interaction (DMI), exchange energy, and the magnetocrystalline anisotropy (MCA) energy were investigated based on density functional theory. Since DMI and MCA are caused by spin--orbit coupling (SOC), they are increased with 5$d$ capping layers which exhibit strong SOC strength. We discover a skyrmion phase by using atomistic spin dynamic simulations at small magnetic fields of $\sim$1 T. In addition, a ground state that a spin spiral phase is remained even at zero magnetic field for both films with 4$d$ and 5$d$ capping layers.

Acute ischemic strokes are the third leading cause of death and the leading cause of neurological disability worldwide. The oxygen and glucose deprivation associated with ischemic strokes not only leads to neuronal cell death, but also increases the inflammatory response and decreases functional output of the brain. The only intervention approved by US Federal Drug and Food Administration for treatment of ischemic strokes is tissue plasminogen activator (tPA), however, such treatment can only be given within 4.5 hours of the onset of stroke-like symptoms. This narrow time-range limits its application, and it also might induce detrimental rather than beneficial effects to stroke patients by treatment of the tPA. In order to reduce the infarct volume of an acute ischemic stroke while increasing the time period for treatment, emerging therapies reveal great potential by targeting inflammation, growth factors, ion channels, and neurotransmitter receptors with monoclonal antibody (MAB). With successfully application in the treatment of cancer patient by MAB, in this review, we will focus on recent advances on stroke therapy by using MAB on the treatment of stroke by targeting inflammation, growth factors, ion channels, and neurotransmitter receptors. Therefore, developing specific MAB targeting the signaling pathway of stroke will contribute to stroke therapy.

The Conus genus includes around 500 species of marine mollusks with a peculiar production of venomous peptides known as conotoxins (CTX). Each species is able to produce up to 200 different biological active peptides. Common structure of CTX is the low number of aminoacids stabilized by disulfide bridges and post-translational modifications that give rise to different isoforms. µ and µ-O CTX are two isoforms that specifically target voltage-gated sodium channels. These, by inducing the entrance of sodium ions in the cell, modulate the neuronal excitability by depolarizing plasma membrane and propagating the action potential. Hyperxcitability and mutations of sodium channels are responsible for perception and transmission of inflammatory and neuropathic pain states. In this review, we describe the current knowledge of µ-CTX interacting with the different sodium channels subtypes, the mechanism of action and their potential therapeutic use as analgesic compounds in the clinical management of pain conditions.

Li-ion cell designs, component integrity and manufacturing processes all have critical influence on the safety of Li-ion batteries. Any internal defective features that induce a short circuit, can trigger a thermal runaway: a cascade of reactions, leading to a device fire. As consumer device manufacturers push aggressively for increased battery energy, instances of field failure are increasingly reported. Notably Samsung made a press release in 2017 following a total product recall of their Galaxy Note 7 mobile phone, confirming speculation that the events were attributable to the battery and its mode of manufacture. Recent incidences of battery swelling on the new iPhone 8 have been reported in the media, and the techniques and lessons reported herein may have future relevance. Here we look deeper into the key components of one of these cells and confirm evidence of cracking of electrode material in tightly folded areas, combined with a delamination of surface coating on the separator, which itself is an unusually thin monolayer. We report microstructural information about the electrodes, battery welding attributes and thermal mapping of the battery whilst operational. The findings point to the most likely combination of events and highlights the impact of design features, whilst providing structural considerations most likely to have led to the reported incidences relating to this phone.

Titanium dioxide (TiO₂) micro and nano architectures have been intensively studied in the past years because of many varied applications in environmental, energy conversion, and storage fields, such as heterogeneous catalysis, dye-sensitized solar cells, lithium/sodium ion batteries, lithium-sulfur (Li-S) batteries, and bio-nanotechnology, etc. Especially the surface and interface structures in the TiO₂ structures play important roles in those applications. This mini review article focuses on TiO₂ micro and nano architectures with the prevalent crystal structures (anatase, rutile, brookite, and TiO₂(B)), and summarizes major advances in the surface and interface engineering and applications in environmental and electrochemical applications. We present the principles and growth mechanisms of TiO₂ nanostructures via different strategies, with an emphasis on rational control of the surface and interface structures. We further discuss the applications of TiO₂ micro and nano architectures in photocatalysis, lithium/sodium ion batteries, and Li-S batteries. Throughout the discussion, the relationship between the device performance and the surface structures of TiO₂ micro/nano structures will be highlighted. Then we discuss the phase transitions of TiO₂ nanostructures and possible strategies of improving the phase stability. The review concludes with a perspective on the current challenges and future research directions.

Solvent-free, single-ion conducting electrolytes are sought after for use in electrochemical energy storage devices. Here, we investigate the ionic conductivity and how this property is influenced by segmental mobility and conducting ion number in crosslinked single-ion conducting polyether-based electrolytes with varying tethered anion and counter-cation types. Crosslinked electrolytes are prepared by the polymerization of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) methyl ether acrylate, and ionic monomers. The ionic conductivity of the electrolytes is measured and interpreted in the context of differential scanning calorimetry and Raman spectroscopy measurements. A lithiated crosslinked electrolyte prepared with PEG₃₁DA and STFSI monomers is found to have a lithium ion conductivity of 3.2 × 10^-6 and 1.8 × 10⁻⁵ S/cm at 55 and 100 °C, respectively. The percentage of unpaired anions for this electrolyte was estimated at about 23% via Raman spectroscopy. Despite the large variances in metal cation – STFSI binding energies as predicted via DFT and large variations in ionic conductivity, STFSI-based crosslinked electrolytes with the same charge density and varying cations (Li, Na, K, Mg, and Ca) were estimated to all have unpaired anion populations in the range of 19 to 29%.

Deep reinforcement learning (DRL) has achieved significant results in many Machine Learning (ML) benchmarks. In this short survey we provide an overview of DRL applied to trading on financial markets, including a short meta-analysis using Google Scholar, with an emphasis on using hierarchy for dividing the problem space as well as using model-based RL to learn a world model of the trading environment which can be used for prediction. In addition, multiple risk measures are defined and discussed, which not only provide a way of quantifying the performance of various algorithms, but they can also act as (dense) reward-shaping mechanisms for the agent. We discuss in detail the various state representations used for financial markets, which we consider critical for the success and efficiency of such DRL agents. The market in focus for this survey is the cryptocurrency market.

In this study, the optimal condition for the extraction of antioxidants from the fruit Buah Mahkota Dewa (Phaleria macrocarpa) was determined by using Response Surface Methodology (RSM). The optimization was applied using central composite design (CCD) to investigate the three independent variables, namely extraction temperature (^oC), extraction time (minutes) and extraction solvent to-feed ratio (%v/v) on the responses of free radical scavenging activity (DPPH), ferric ion reducing power assay (FRAP), total phenolic content (TPC) and total flavonoid content (TFC).The optimal conditions for the antioxidants extraction were found to be extraction temperature (64^oC), extraction time (66 minutes) and solvent to-feed ratio (75 %v/v) with the highest percentage yield of DPPH, FRAP, TPC and TFC were 86.85%, 7.47%, 292.86 mg/g and 3.22 mg/g respectively. Moreover, the data were subjected to response surface methodology (RSM) and the results showed that the polynomial equations for all models were significant, did not show lack of fit, and presented adjusted determination coefficients (R²) above 99%, proving the yield of phenolic, flavonoid and antioxidants activities obtained experimentally were close to the predicted values and the suitability of the model employed in RSM to optimize the extraction conditions. Hence, in this study, the fruit from P.macrocarpa could be considered to have the strong antioxidant ability and can be used in various cosmeceutical or medicinal applications.

Zinc oxide (ZnO) nanostructures have been studied extensively in the past years due to the novel electronic, photonic, mechanical and electrochemical properties. Recently, more attention has been paid to assemble nanoscale building blocks into three dimensional (3D) complex hierarchical structures, which not only inherit the excellent properties of the single building blocks but also provide potential applications in the bottom-up fabrication of functional devices. This review article focuses on 3D ZnO hierarchical nanostructures, and summarizes major advances in the solution phase synthesis, applications in environment, and electrical/electrochemical devices. We present the principles and growth mechanisms of ZnO nanostructures via different solution methods, with an emphasis on rational control of the morphology and assembly. We then discuss the applications of 3D ZnO hierarchical nanostructures in photocatalysis, field emission, electrochemical sensor, and lithium ion batteries. Throughout the discussion, the relationship between the device performance and the microstructures of 3D ZnO hierarchical nanostructures will be highlighted. This review concludes with a personal perspective on the current challenges and future researches.

The perpendicular exchange bias effect is observed in the ferromagnetic Co/Ni multilayers adjacent to the antiferromagnetic FeRh layer. It is found that as the antiferromagnetic FeRh thickness increases from 10 Å to 50 Å, the hysteresis loop is gradually changed from the symmetric shape to the asymmetric shape shifted by some amount corresponding to the exchange-biased field at the thickness of 25 Å. Also, the magnetic domain observation experiment confirms that the domain reversals in the increasing and the decreasing field regions of the sample with the thickness of 50 Å exhibit the same single domain wall motion even though they have the different coercivities.

The majority of E-commerce transactions reveal private information such as customers' identities, order contents, and payment information during the transaction. Other personal information such as health conditions, religion, and even ethnicity may be also deduced. Even when deploying electronic cryptocurrencies such as Bitcoin, anonymity cannot be fully guaranteed. Also, many anonymous payment schemes suffer from possible double spending circumstances. E-commerce privacy is basically a difficult problem as it involves parties with concurring interests. Three major e-commerce requirements are highly difficult to resolve: anonymous purchase, anonymous delivery, and anonymous payment. This work presents a possible e-commerce system addressing all three anonymity requirements for electronic-items business on open networks. The system offers anonymous entities authentication mechanisms up to completing a fair anonymous e-commerce transaction. The system is based on deploying a physically clone-resistant hardware token for each relevant involved party. The tokens are made clone-resistant by accommodating a Secret Unknown Cipher (SUC) in each hardware-token as a digital PUF-like identity. A set of novel generic system-setups for units, protocols and e-commerce schemes is introduced. The proposed anonymization is basically attained by virtually-replacing relevant e-commerce entities by low-cost, unique and clone-resistant tokens/units using SUCs. The units act as trustable anonymous, authenticated and non-replaceable entities monitored by their acting users.

The Algiers Stock Exchange (ASE) is the only stock exchange in Algeria. It’s one of the newest and smallest emerging stock exchanges in the world. The focus of this paper is to model and forecast monthly returns of the ASE index (DZAIRINDEX) using The Box- Jenkins methodology. The period of this study is from Jun 2010 to July 2019. According to Akaike’s Information Criterion (AIC) estimator, the Seasonal Autoregressive Integrated Moving Average SARIMA(2,0,0)(0,0,1) is chosen as the best model for forecasting the monthly DZAIRINDEX returns. Diagnostic tests confirm that the fitted model is adequate, where the residuals of this model are normally distributed with no autocorrelation and no heteroskedasticity. The forecast of the monthly DZAIRINDEX returns for one year ahead using this model shows a decreasing fluctuations trend. Based on different measures of forecast accuracy such as ME, MAE, RMSE, MASE, we show that the forecast accuracy of SARIMA(2,0,0)(0,0,1) is acceptable and this model performs much better than a naïve model. These results could be used by the financial communities in Algeria to deal with stock exchange risks and to improve their decisions.

Electric Vehicles (EVs) are the need of the hour due to growing climate change problems linked with the transportation sector. Battery Thermal Management System (BTMS), which is accountable for certifying safety and performance of lithium-ion batteries (LiB), is the most vital part of an EV. LiB has auspicious gravimetric energy density but the heat generation due to chemical reactions inside a LiB during charging and discharging causes temperature rise which has a direct effect on LiB performance and safety. This study specifically focuses on aircooled BTMS, defines different types of air-cooled BTMS (active and Passive), discusses limitations associated with air-cooled BTMS, and investigates different optimization techniques and parameters to improve performance of air-cooled BTMS. Maintaining temperature within optimum range and uniform temperature distribution between cells of a battery pack are the major design parameters for improving the performance and efficiency of air-cooled BTMS. Various optimization techniques including cell arrangement with a battery pack, air-flow channel optimization, and air inlet/outlet position variations are discussed and each technique is thoroughly reviewed. Finally, it’s noted that passive air-cooled BTMS is not that effective for long-distance vehicles so most researchers shifted their focus toward active air-cooled BTMS. Active air-cooled BTMS requires a lot of power for effective performance. Lastly, the most recent field of air-cooled BTMS technology which is Air-Hybrid BTMS is discussed and declared a very promising solution for overcoming major limitations associated with air-cooled BTMS.

Cycling reliability is crucial for Si-based materials due to severe volume change during cycles that results in the fast capacity fading. Though the binder only occupies a very low amount of the total mass of anodes, it is proved to perform a key parameter to improve the cycle performance of Si-based anodes. Because they are eco-friendly and cost saving, water-based binders styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) are regarded as the better binder to substitute Poly (vinylidene difluoride) (PVDF) as the binder for Si-based anode. In this study, the anodes are fabricated by simply mixing the active materials (naso Si, graphite and conductive additive) together and using the mixture of SBR and CMC as a binder. The results showed that the retention capacities of the anodes are more than 440 mAh/g after 400 cycles. It indicates that it is an easy and simple way to make high performance anodes.

Dental caries is a public health problem worldwide according to WHO data. Among treatments in pediatric dentistry, prefabricated metal crowns (PMCs) have been one of the most successful options since they were introduced in cases of considerable tooth destruction. Our objective was to detect the presence and concentration of iron (Fe), chromium (Cr), and nickel (Ni) in saliva of patients who require rehabilitation with PMCs, before and after their placement. A quasi-experimental study was performed in 32 patients who attended dental care in a pediatric dentistry clinic at a public university and who required rehabilitation with PMCs. Parametric tests (ANOVA and Pearson correlation) were performed, and a p ≤ 0.05 was considered statistically significant. Statistically significant differences were found when comparing the Ni release before, 1 week, and 1 month after placing the crowns. Similarly, we observed a positive correlation between the number of crowns and Ni release. No tests were performed for Fe and Cr because the amounts of these metals were less than 0.1 ppb, which was not detectable by inductively coupled plasma optical emission spectrometry (ICP-OES). The levels of Fe, Cr, and Ni released were below toxic health levels. Studies are required to evaluate whether this release has negative effects at cellular levels.

The blue sepal color of hydrangea is due to a metal complex anthocyanin composed of 3-O-glucosyldelphinidin (1) and an aluminum ion with the co-pigments 5-O-caffeoylquinic acid (2) and/or 5-O-p-coumaroylquinic acid (3). The three components, namely, anthocyanin, Al³⁺ and 5-O-acylquinic acids, are essential for blue color development, but the complex is unstable and only exists in aqueous solution. Furthermore, the complex did not give analyzable NMR spectra or crystals. Therefore, many trials to determine the detailed chemical structure of the hydrangea-blue complex have failed to date. Instead, via experiments mixing 1, Al³⁺ and 2 or 3 in a buffered solution at pH 4.0, we obtained the same blue solution derived from the sepals. However, the ratio was not stoichiometric but fluctuated. To determine the composition of the complex, we tried direct observation of the molecular ion of the complex using electrospray-ionization mass spectrometry. In a very low-concentration buffer solution (2.0 mM) at pH 4.0, we reproduced the hydrangea-blue color by mixing 1, 2 and Al³⁺ in ratios of 1:1:1, 1:2:1 and 1:3:1. All solution gave the same molecular ion peak at m/z = 843, indicating that the blue solution has a ratio of 1:1:1 for the complex. By using 3, the observed mass number was m/z = 827 and the ratio of 1, 3 and Al³⁺ was also 1:1:1. A mixture of 1, 3-O-caffeoylquinic acid (4) and Al³⁺ did not give any blue color but instead was purple, and the intensity of the molecular ion peak at m/z = 843 was very low. These results strongly indicate that the hydrangea blue-complex is composed of a ratio of 1:1:1 for 1, Al³⁺ and 2 or 3.

It is well known that that there is an intrinsic link between the financial and energy sectors, which can be analyzed through their spillover effects, which are measures of how the shocks to returns in different assets affect each other’s subsequent volatility in both spot and futures markets. Financial derivatives, which are not only highly representative of the underlying indices, but can also be traded on both the spot and futures markets, include Exchange Traded Funds (ETFs), a tradable spot index whose aim is to replicate the return of an underlying benchmark index. When ETF futures are not available to examine spillover effects, “generated regressors” are useful for constructing both Financial ETF futures and Energy ETF futures. The purpose of the paper is to investigate the co-volatility spillovers within and across the US energy and financial sectors in both spot and futures markets, by using “generated regressors” and a multivariate conditional volatility model, namely Diagonal BEKK. The daily data used are from 1998/12/23 to 2016/4/22. The data set is analyzed in its entirety, and are also subdivided into three distinct subsets. The empirical results show there is a significant relationship between the Financial ETF and Energy ETF in the spot and futures markets. Therefore, financial and energy ETFs are suitable for constructing a financial portfolio from an optimal risk management perspective, and also for dynamic hedging purposes.

The feasibility of using full ion kinetics, instead of gyrokinetics, in simulating low-frequency Ion-Temperature-Gradient (ITG) instabilities in tokamaks has recently been demonstrated by Sturdevant et al. [Physics of Plasmas 24, 081207 (2017)]. In that work, a variational integrator was developed to integrate the full orbits of ions in toroidal geometry, which proved to be accurate in capturing both the short-time scale cyclotron motion and long time scale drift motion. The present work extends that work in three aspects. First, we implement a relatively simple full orbit integrator, the Boris integrator, and demonstrate that the accuracy of this integrator is also sufficient for simulation of ITG instabilities. Second, the equilibrium magnetic configuration is extended to general toroidal configuration specified numerically, enabling simulation of realistic equilibria reconstructed from tokamak experiments. Third, we extend that work to the nonlinear regime and investigate the nonlinear saturation of ITG instabilities. To verify the new numerical implementation of the orbit integrator and magnetic configuration, the linear electrostatic ITG frequency and growth rate are compared with those given in Sturdevant's work and good agreement is found.

Objective: Rett syndrome (RTT) is an X-linked neurodevelopmental disorder caused by mutations in MeCP2, a transcription factor. MeCP2 mutations cause abnormal expression of downstream genes and eventually lead to brain dysfunction. The role of MeCP2 in brain neural development remains unclear. To further elucidate this role, a MeCP2-null rat model was created with the CRISPR/cas9 system. Method: A MeCP2-cas9 vector was constructed and then microinjected into fertilized rat ova in vitro. Two mutations by CRISPR/cas9 were confirmed to cause deletions in exon 2 of MeCP2 via DNA sequencing, and protein expression was measured by Western blotting. Transcriptome data for three brain tissues, the cerebellum, cerebral cortex and hippocampus, were obtained via next-generation sequencing. Results: MeCP2-null rats were successfully obtained, and preliminary analysis showed that the MeCP2-null rats exhibited motor dysfunction and anxious and depressed behaviour. In addition, differentially expressed genes (DEGs) were identified in the three MeCP2-null brain tissues compared to wild-type rat brain tissues. In the rat cerebellum, 388 downregulated DEGs were mainly involved in the calcium ion signalling pathway and the PI3K-Akt signalling pathway. In the cerebral cortex, 386 upregulated DEGs were primarily involved in intracellular signal transduction, protein phosphorylation and the MAPK signalling pathway. In the hippocampus, the DEGs were related to the MAPK signalling pathway. Conclusion: We constructed a MeCP2-null rat model with unique features with CRISPR/cas9 technology to study RTT and analysed DEGs in three rat brain tissues to highlight potential targets for the development of new medicines.

Plasma treatment of soft polymers is the promising technique to improve biomedical properties. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading (50000 cycles, frequency – 1 Hz, strain amplitude – 10, 20, 40%). The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer) and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface.

The present reality of the Nigerian economy is the fact that inflation has remained unabated in spite of all exchange rate measures that have been adopted by the monetary authority. This calls for investigation into the extent to which exchange rate impact on inflation in Nigeria. The research paper examined the impact of exchange rate depreciation on inflation in Nigeria for the period 1981–2017, using Auto Regressive Distributed Lag (ARDL) Bounds Test Cointegration Procedure. The research shows that inflation rate in Nigeria is highly susceptible to lagged inflation rate, exchange rate, lagged exchange rate, lagged broad money, and lagged gross domestic product at 5% level of significance. A long run relationship was also found to exist between inflation rate, gross domestic product and general government expenditure, indicating that the model has a self-adjusting mechanism for correcting any deviation of the variables from equilibrium. Therefore, this study concludes that exchange rate is an important tool to manage inflation in the country; thus, this paper recommends that policies that have direct influence on inflation as well as exchange rate policies that would checkmate inflation movement in the country, should be used by the Central Bank of Nigeria. Also, monetary growth and import management policies should be put in place to encourage domestic production of export commodities, which are currently short-supplied. In addition, policy makers should not rely on this instrument totally to control inflation, but should use it as a complement to other macro-economic policies.

Magnetic nanoparticles are met across many biological species ranging from magnetosensitive bacteria, fishes, bees, bats, rats, birds, to humans. They can be both of biogenetic origin and due to environmental contamination, being either in paramagnetic or ferromagnetic state. The energy of such naturally occurring single-domain magnetic nanoparticles can reach up to 10-20 room k_BT in the magnetic field of the Earth, which naturally led to supposition that they can serve as sensory elements in various animals. This work explores within a stochastic modeling framework a fascinating hypothesis of magnetosensitive ion channels with magnetic nanoparticles serving as sensory elements, especially, how realistic it is given a highly dissipative viscoelastic interior of living cells and typical sizes of nanoparticles possibly involved.

Anion exchange membrane (AEM) electrolysis is hampered by two main issues: stability and performance. Focusing on the latter, this work demonstrates a highly active NiMo cathode for hydrogen evolution in AEM electrolysis. We demonstrate an electrolyzer performance of 1 A cm⁻² at 1.9 V (total cell voltage) with a NiMo loading of 5 mg cm⁻² and an iridium black anode in 1 M KOH at 50 °C, that may be compared to 1.8 V for a similar cell with Pt at the cathode. The catalysts developed here will be significant in supporting the pursuit of cheap and environmentally friendly hydrogen fuel.

Various types of electroconductive additives were evaluated for high C-rate capability in an attempt to extend practical application of high-areal-capacity lithium–sulfur batteries that employ an aluminum-foam current collector. Carbon nanofibers (CNFs) were found to be the most effective additive, with the ability to attain a high-sulfur-loading of 40 mg cm−2. A CNF-containing cell exhibited gravimetric capacities of 1094 and 758 mAh gsulfur−1 (46.8 and 32.4 mAh cm−2) at 0.05 and 0.1 C-rate, respectively, in an ether-based electrolyte. Because a CNF-containing slurry exhibits low viscosity even at a high solid ratio, it could be filled into the aluminum foam. Additionally, a lithium–sulfur battery with high-sulfur-loading had an energy density of ~120 Wh kg−1, a value that was calculated from the weight of the components of the cathode, anode, current collectors, electrolyte, and separator. Assuming that the amount of electrolyte decreases and that the energy density of cells accumulate, a theoretical energy density of 522 Wh kg−1 was estimated. Moreover, it was found that even if a high-areal-capacity was achieved, the discharge capacity converged at a high C-rate, unless there was an improvement in ion diffusion in the bulk electrolyte. This is considered a limitation of sulfur cathodes with high-sulfur-loading.

Leaf temperature (T_leaf) influences photosynthesis and respiration. Currently, there is a growing interest on including lianas in productivity models due to their increasing abundance, and their detrimental effects on net primary productivity in tropical environments. Therefore, understanding the differences of T_leaf between lianas and trees is important for future of forest on whole ecosystem productivity. Here we determined the displayed leaf temperature (T_d= T_leaf – ambient temperature) of several species of lianas and their host trees during ENSO and non-ENSO years to evaluate if the presence of lianas affects the T_d of their host trees, and if leaves of lianas and their host trees exhibit differences in T_d. Our results suggest that close to midday, the presence of lianas does not affect the T_d of their host trees; however, lianas tend to have higher values of T_d than their hosts across seasons, in both ENSO and non-ENSO years. Although lianas and trees tend to have similar physiological-temperature responses, differences in T_d could lead to significant differences in rates of photosynthesis and respiration based temperature response curves. Future models should thus consider differences in leaf temperature between these life forms to achieve robust predictions of productivity.

Carbon supported nanoparticles of monometallic Ni catalyst and binary Ni-Transition Metal (Ni-TM/C) electrocatalytic composites were synthesized via chemical reduction method, where TM stands for the doping elements Fe, Co, and Cu. The chemical composition, structure and morphology of the Ni-TM/C materials were characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM) and energy-dispersive X-ray spectroscopy (EDS). The electrochemical properties towards hydrogen oxidation reaction in alkaline medium were studied using the rotating disc electrode and cycling voltammetry methods. A significant role of the TM dopant in the promotion of the hydrogen electrooxidation kinetics of the binary Ni-TM/C materials were revealed. A record-high in exchange current density value of 0.060 mA cm²_Ni was measured for Ni₃Fe₁/C, whereas the monometallic Ni/C counterpart has only shown 0.039 mA cm²_Ni. In order to predict the feasibility of the electrocatalysts for hydrogen chemisorption, density functional theory was applied to calculate the hydrogen binding energy and hydroxide binding energy values for bare Ni and Ni₃TM₁.

The influence of both the absolute values of the dollar/ruble exchange rate (rate) and its changes per day on the balance of the Bank of Russia operations for ruble liquidity provision and absorption (saldo) was investigated. Daily data were used from January 2015 to April 2018. It was found that the change in the rate 6 days ago is the cause (according to Granger) of the saldo value. For the saldo dynamics, an oscillatory model with an external force - a change in the rate - is proposed. Using the Kalman filter, the model parameters were estimated and saldo forecasted. Found period of self-oscillation is 4.218 days and attenuation of the amplitude for a day in 2.179 times. The rate growth of 1 RUB, after 6 days, causes saldo increase of approximately 20 billion rubles. In fact, the changes in rate cause the variability of the saldo not more than for found coefficient of determination (26.7%), but the "change in the rate-liquidity saldo" system during the crisis-free period has a high "Q-factor," and changes in the rate, repeated with a period close to self-one, can cause large-amplitude fluctuations in saldo.

We describe our investigations of the surface physicochemical and biological properties of polylactic acid modified by silver, argon and carbon ion implantation to doses of 1 × 10¹⁴, 1 × 10¹⁵ and 1 × 10¹⁶ ion/cm² at energies of 20 keV (for C and Ar) and 40 keV (for Ag). X-ray analysis shows enhancement of coherent scattering regions and lattice constant increase after ion implantation. Secondary electron mass-spectrometry indicates that Ag concentration in the subsurface layer is less than 80%, but at a depth of 500 nm does not exceed 1–2%. The silver forms metal particles in the subsurface layer rather than making additional chemical bonds with polymer atoms. Atomic force microscopy reveals that the higher the irradiation dose the larger the surface roughness of the samples. Ag-irradiated samples implanted to a dose of 1 × 10¹⁶ ions/cm² have the highest roughness, 190 nm. Our investigation of the cytotoxicity of two individual donor macrophages shows that Ag-implanted polylactic acid has no negative impact on immune system cells and could be a promising material for biomedical application.

In this paper, a new anode environmentally friendly for hydrogen production was developed based on 430 stainless steel with an electrodeposited cobalt layer. The novelty of this work is the cobalt source once the electrodeposition bath was obtained from recycling of spent Li-ion batteries cathode with composition LiCoO₂. The electrodeposited cobalt behaves as supercapacitor in KOH 1M. In the linear voltammetry in KOH 1M, when the overpotential reaches 370 mV, the anodic density current for 430 SS/Co is 19 mA cm⁻². Thus, the anode developed in this paper achieves the double of density current with half of production cost if compared with 316SS. Moreover the anode construction described in this paper is an excellent option for Li- ion battery recycling.

Atomic structure of N-electron atoms is often determined using the Hartree-Fock method, which is an integro-differential equation. The exchange term of the Hartree-Fock equations is usually treated as an inhomogeneous term of a differential equation, or with a local density approximation. This work uses matrix methods to solve for the Hartree-Fock equations, rather than the more commonly-used shooting method to integrate an inhomogeneous differential equation. It is well known that a derivative operator can be expressed as a matrix made of finite-difference coefficients; energy eigenvalues and eigenvectors can be obtained by using computer linear-algebra packages. We extend the same technique to integro-differential equations, where a discretized integral can be written as a sum in matrix form. This method is compared against experiment and standard atomic structure calculations. We also can use this method for free-electron wavefunctions. This technique is important for spectral line broadening in two ways: improving the atomic structure calculations, and improving the motion of the plasma electrons that collide with the atom.

In Shark Bay, a large hypersaline bay in Western Australia, longitudinal density gradients force gravitational circulation that is important for Bay-ocean exchange. Observations of vertical stratification and velocity are presented, confirming a steady near-bed dense water outflow from Shark Bay’s northern Geographe Channel that persisted through all stages of the tide. Outflow velocities were 2–3 times stronger than the outflows recorded previously in Naturaliste Channel (in the west) and were more resistant to breakdown by tidal mixing. Estimates of turbulent kinetic energy production derived from ADCP data using the variance method showed a more complex structure in Geographe Channel, due to shear associated with the stratified conditions, with peak levels of turbulence occurring during reversal of tidal flows. For both channels the main source of turbulence was tidal flow along the seabed, with the bottom current speed cubed, |U_b³|, providing a reasonable proxy for tidal mixing and prediction of dense water outflows from Shark Bay the majority of the time. Orientation and deeper water of Geographe Channel along the main axis of the longitudinal density gradient provided an explanation for the predominant outflow from the Bay’s northern entrance. These density-driven currents could potentially influence recruitment of commercially fished scallops and prawns through dispersal and flushing of larvae.

In this paper, we investigate the “statics and dynamics” return and volatility spillovers transmission across developed and developing countries. Quoted against the U.S. dollar, we study twenty-three global currencies over 2005 – 2016. Focusing on the spillover index methodology, the generalised VAR framework is employed. Our findings indicate no evidence of bi-directional return and volatility spillovers between developed and developing countries. However, a unidirectional volatility spillover from developed to developing countries is highlighted. Furthermore, our findings document significant bi-directional volatility spillovers within the European region (Eurozone and non-Eurozone currencies) with the British Pound (GBP) and the Euro (EUR) as the most significant transmitters of volatility. The findings reiterate the prominence of volatility spillovers to financial regulators.

The accurate monitoring of state of charge (SOC) and state of health (SOH) is critical for the reliable management of lithium-ion battery (LIB) systems. In this paper, the online model identification is scrutinized to achieve high modeling accuracy and robustness, and a model-based joint estimator is further proposed to estimate the SOC and SOH of LIB concurrently. Specifically, an adaptive forgetting recursive least squares (AF-RLS) method is exploited to optimize the estimation alertness and numerical stability, so as to achieve accurate online adaption of model parameters. Leveraging the online adapted battery model, a joint estimator is proposed by combining an open-circuit voltage (OCV) observer with a low-order state observer to co-estimate the SOC and capacity of LIB. Simulation and experimental studies are performed to evaluate the performance of the proposed data-model fusion method. Results suggest that the proposed method can effectively track the variation of model parameters by using the onboard measured current and voltage data. The SOC and capacity can be further estimated in real time with fast convergence, high accuracy and high stability.

WHO was informed on 31 December 2019 of cases of unknown cause pneumonia in Wuhan City, China. On 7 January 2020 Chinese authorities reported a novel coronavirus as the cause and was temporarily labeled "2019-nCoV." Coronaviruses (CoV) are a wide family of viruses which cause diseases ranging from common cold to more serious illnesses. A novel coronavirus (nCoV) is a new strain not previously found in humans. Countries around the globe have stepped up their surveillance to quickly detect any new 2019-nCoV cases. Blockchain is developing into a safe and efficient network for secure data sharing in applications such as the financial industry, operations management, food industry, energy market, the Internet of Things and healthcare. In this paper, we are using blockchain technology as a mean to share authentic data, tracking of relevant information and help speed up the treatment process. At the same time it will preserve person’s identity. Timely deployment and suitable implementation of the proposed model have the opportunity to curb COVID-19 transmissions and associated mortality, especially in environments with inadequate access to testing facilities. This work will also facilitate in the treatment of other infectious diseases. Smart contract have been designed and implemented using the ethereum blockchain platform which has been presented in this paper. This work would facilitate multiple stakeholders who are involved within the medical system to curb the transmission of this disease.

The reliable online analysis of volatile compounds in exhaled breath remains a challenge as a plethora of molecules occur in different concentration ranges (i.e. ppt to %), and need to be detected against an extremely complex background matrix. While this complexity is commonly addressed by hyphenating a specific analytical technique with appropriate preconcentration and/or preseparation strategies prior to detection, we herein propose the combination of three analytical tools based on truly orthogonal measurement principles as an alternative solution: field-asymmetric ion mobility spectrometry (FAIMS), Fourier-transform infrared (FTIR) spectroscopy-based sensors utilizing substrate-integrated hollow waveguides (iHWG), and luminescence sensing (LS). These three tools have been integrated into a single compact analytical platform suitable for online exhaled breath analysis. The analytical performance of this prototype system was tested via artificial breath samples containing nitrogen (N2), oxygen (O2), carbon dioxide (CO2) and acetone as a model volatile organic compound (VOC) commonly present and detected in breath. Functionality of the combined system was demonstrated by detecting these analytes in their respectively breath-relevant concentration range and mutually independent of each other generating orthogonal yet correlated analytical signals. Finally, adaptation of the system towards the analysis of real breath samples during future studies is discussed.

Tough and antimicrobial dual-crosslinked poly((trimethylamino)ethyl methacrylate chloride)-phytic acid hydrogel (pTMAEMA-PA) has been synthesized by adding chemical crosslinker and docking physical crosslinker of multivalent phytic acid into a cationic polyelectrolyte network. By increasing the loading concentration of PA, the tough hydrogel exhibits compressive stress of >1 MPa, along with high elasticity and fatigue-resistant properties. The enhanced mechanical properties of pTMAEMA-PA were stem from multivalent ion effect of PA via the formation of ion bridges within polyelectrolytes. In addition, a comparative study for a series of pTMAEMA-counterion complexes was conducted to elaborate the relationship between swelling ratio and mechanical strength. The study also revealed secondary factors, such as ion valency, ion specificity and hydrogen bond formation, holding crucial roles in tuning mechanical properties of the polyelectrolyte hydrogel. Furthermore, in bacteria attachment and disk diffusion tests, pTMAEMA-PA exhibits superior fouling resistance and antibacterial capability. The results reflect the fact that PA enables chelating strongly with divalent metal ions, hence, disrupting the outer membrane of bacteria, as well as dysfunction of organelles, DNA and protein. Overall, the work demonstrated a novel strategy for preparation of tough polyelectrolyte with antibacterial capability via docking PA to open up the potential use of PA in medical application.

Driven by the rapid uptake of battery electric vehicles, Li-ion power batteries are increasingly reused in stationary energy storage systems, and eventually recycled to recover all the valued components. Offering an updated global perspective, this study provides a circular economy insight on lithium-ion battery reuse and recycling.

A study is reported on the electrochemical alloying-dealloying properties of Mg₂Sn intermetallic compounds. ¹¹⁹Sn Mössbauer spectra of β-Sn powder, thermally alloyed cubic-Mg₂Sn and an intermediate MgSn nominal composition are used as references. The discharge of a Mg/micro-Sn half-cell led to significant changes in spectra line shape that are explained by a multiphase mechanism involving the coexistence of c-Mg₂Sn, distorted Mg_2-δSn and Mg-doped β-Sn. Capacities and capacity retention were improved by using nanoparticulate tin electrodes. This material reduces significantly the diffusion lengths for magnesium and contains surface SnO and SnO₂, which are partially electroactive. The half-cell potentials were suitable to be combined versus MgMn₂O₄ cathodes. Energy density and cycling properties of the resulting full Mg-ion cells are also scrutinized.

Forest carbon sequestration is a widely accepted natural climate solution, however, methods to determine net carbon offsets are limited to commercial carbon proxies and CO2 eddy covariance research. Non-CO2 greenhouse gases (GHG) (e.g., CH4, N2O) receive less attention in the context of forests, in part, due to emphasis on CO2 and the operational requirements and cost for three-gas eddy covariance platforms. In this study, Howland forest flux tower (CO2, CH4) and soil flux data (CO2, CH4, N2O), representing net emission reductions, are linked to their respective social costs to estimate commercial revenue if sold as a GHG social cost forest offset product (GHG-SCF). Estimated annual revenue for GHG-SCF products, applicable to realization of a Green New Deal, range from 120,000 covering the site area of 557 acres in 2021, to 12,000,000 for extrapolation to 40,000 acres in 2040, assuming a 3% discount rate. The Howland Forest CO2 flux record for two adjacent towers is compared to California Air Resources Board forest carbon proxy data for compliance sequestration offsets, the only project site where these approaches overlap. Overcrediting, incomplete carbon accounting with annual errors of up to 2,256%, inadequate third-party verification, and limited application to non-CO2 GHG’s are established. In contrast, direct measurement of one or more GHG’s offers new forest products and revenue incentives to restore and conserve forests worldwide.

The garnet Li₇La₃Zr₂O₁₂ (LLZO) has been widely investigated because of its high conductivity, wide electrochemical window and chemical stability to lithium metal. However, the usual preparation process of LLZO requires a long time of high-temperature sintering and a lot of mother powders against the lithium evaporation. The submicron Li₆.6La₃Zr₁.6Nb₀.4O₁₂ (LLZNO) powders are prepared by conventional solid-state reaction method and attrition milling process, which are stable cubic phase and have high sintering activity, and Li stoichiometric LLZNO ceramics are obtained by sintering at a relative lower temperature or for a short time by using these powders which are difficult to control under high sintering temperature and long sintering time. The particle size distribution, phase structure, microstructure, distribution of element, total ionic conductivity, relative density and activation energy of submicron LLZNO powders and LLZNO ceramics are tested and analyzed by laser diffraction particle size analyzer, XRD, SEM, EIS and Archimedean method. The total ionic conductivity of sample sintered at 1200 °C for 30 min is 5.09 × 10-4 S·cm-1, the activation energy is 0.311 eV, and the relative density is 87.3%, and sintered at 1150 °C for 60 min total ionic conductivity is 3.49 × 10-4 S·cm-1, the activation energy is 0.316 eV, and the relative density is 90.4%. At the same time, all-solid-state batteries are assembled with LiMn₂O₄ as positive electrode and submicron LLZNO powders as solid state electrolyte. After 50 cycles, the discharge specific capacity is 105.5 mAh/g and the columbic efficiency is above 95%.

Immobilized metal ion affinity adsorbents have been widely used in separation technique to purify proteins. Due to the leakage of metal ion from the adsorbents, there is no metal ion affinity adsorbent for hemoperfusion has been applied to clinical trial. In this study, in order to prevent the leakage of Zn²⁺ loaded from cellulose beads based adsorbent, improve its stability and adsorption capacity for testosterone, Freeze-drying method was used to enhance the porosity of cellulose beads, improve the surface area of the cellulose beads and adsorption capacity for testosterone. Chitosan was used to coat the adsorbents for preventing the leakage of Zn²⁺ loaded and improve the adsorbent’s stability. Moreover, the factors affecting adsorption ability and some components in plasma were also investigated. The results indicate the adsorption ability of the adsorbent can be significantly improved by freeze-drying. After the adsorbent was coated with 0.02% chitosan solution, the highest adsorption percentage reached 48%. During adsorption, the Zn²⁺ concentration in plasma did not rise. In addition, the adsorption percentage for total proteins was below 15%. The results may be caused by the pore size and surface area of the adsorbent enlarged via freeze-drying, and the chitosan solution went into the pores and coated the outer and inner surface of the adsorbent. The adsorbent has a potential clinical application to remove testosterone in patients with recurrent and metastatic prostate cancer.

This review discusses a broad range of recent advances (2013-2017) of chemical imaging using electrochemical methods, with a particular focus on techniques that have been applied to study cellular processes, or techniques that show promise for use in this field in the future. Non-scanning techniques such as microelectrode arrays (MEAs) offer high time-resolution (< 10 ms) imaging, however at reduced spatial resolution. In contrast, scanning electrochemical probe microscopies (SEPMs) offer higher spatial resolution (as low as a few nm per pixel) imaging, with images collected typically over many minutes. Recent significant research efforts to improve the spatial resolution of SEPMs using nanoscale probes, and to improve the temporal resolution using fast scanning have resulted in movie (multiple frame) imaging with frame rates as low as a few seconds per image. Many SEPM techniques lack chemical specificity or have poor selectivity (defined by the choice of applied potential for redox-active species). This can be improved using multifunctional probes, ion-selective electrodes and tip-integrated biosensors, although additional effort may be required to preserve sensor performance after miniaturization of these probes. We discuss advances to the field of electrochemical imaging, and technological developments which are anticipated to extend the range of processes that can be studied. This includes imaging cellular processes with increased sensor selectivity and at much improved spatiotemporal resolution than has been previously customary.

Water electrolysis provides efficient and cost-effective production of hydrogen from renewable energy. Currently, the oxidation half-cell reaction relies on noble-metal catalysts, impeding widespread application. In order to adopt water electrolyzers as the main hydrogen production systems, it is critical to develop inexpensive and earth-abundant catalysts. This review discusses the proton exchange membrane (PEM) water electrolysis (WE) and the progress in replacing the noble-metal catalysts with earth-abundant ones. Researchers within this field are aiming to improve the efficiency and stability of earth-abundant catalysts (EACs), as well as to discover new ones. The latter is particularly important for the oxygen evolution reaction (OER) under acidic media, where the only stable and efficient catalysts are noble-metal oxides, such as IrO_x and RuO_x. On the other hand, there is significant progress on EACs for the hydrogen evolution reaction (HER) in acidic conditions, but how many of these EACs have been used in PEM WEs and tested under realistic conditions? What is the current status on the development of EACs for the OER? These are the two main questions this review addresses.

Bioelectrochemical systems (BES) encompass a group of biobased technologies capable of directly converting organic matter into electricity. In these systems, which are derived from conventional electrochemical systems, the ion exchange membrane represents a key element because of its influence on the economic feasibility and on the performance of BES. This study examines the impact of long-term operation of a BES on the mechanical, chemical and electrochemical properties of five different kind of cation exchange membranes (Nafion-117, CMI-7001, Zirfon UTP 500, FKE and FKB) through several techniques: (i) scanning electron microscopy (SEM) and atomic force microscopy (AFM) to assess the changes on the membranes surface, (ii) thermogravimetric analysis (TGA) to evaluate the structural stability of the membranes, and (iii) ion exchange capacity (IEC) to monitor any change in their electrochemical properties. Results confirmed that there is not an ideal membrane for BES. While Nafion and CMI-7000 exhibited the strongest chemical structure, they also underwent the highest fouling as revealed by a fast increase in surface roughness.

In this report we have discussed the important role of molecular modeling, especially the use of the molecular dynamics method, in investigating transport processes in nanoporous materials such as membranes. With the availability of high performance computers, molecular modeling can now be used to study rather complex systems at a fraction of the cost or time requirements of experimental studies. Molecular modeling techniques have the advantage of being able to access spatial and temporal resolution which are difficult to reach in experimental studies. For example, sub-Angstrom level spatial resolution is very accessible as is sub-femtosecond temporal resolution. Due to these advantages, simulation can play two important roles: Firstly because of the increased spatial and temporal resolution, it can help understand phenomena not well understood. As an example, we discuss the study of reverse osmosis processes. Before simulations were used it was thought the separation of water from salt was purely a coulombic phenomenon. However, by applying molecular simulation techniques, it was clearly demonstrated that the solvation of ions made the separation in effect a steric separation and it was the flux which was strongly affected by the coulombic interactions between water and the membrane surface. Additionally, because of their relatively low cost and quick turnaround (by using multiple processor systems now increasingly available) simulations can be a useful screening tool to identify membranes for a potential application. To this end, we have described our studies in determining the most suitable zeolite membrane for redox flow battery applications. As computing facilities become more widely available and new computational methods are developed, we believe molecular modeling will become a key tool in the study of transport processes in nanoporous materials.

Background: We investigated ion channels at the skin, including peripheral nerve endings, which serve as output machines and molecular integrators of many pruritic inputs mainly received by multiple G protein-coupled receptors (GPCRs). Methods: Based on the level of chronic kidney disease–associated pruritus (CKD-aP), subjects were divided into two groups: non-CKD-aP (no or slight pruritus; n=12) and CKD-aP (mild, moderate, or severe pruritus; n=11). Skin samples were obtained from the forearm or elbow during operations on arteriovenous fistulas. We measured ion channels expressed at the skin, including peripheral nerve endings by RT-PCR: Nav1.8, Kv1.4, Cav2.2, Cav3.2, BKCa, Anoctamin1, TRPV1, TRPA1, and ASIC. Results: Expression of Cav3.2, BKCa, and anoctamin1 was significantly elevated in patients with CKD-aP. On the other hand, expression of TRPV1 was significantly reduced in these patients. We observed no significant difference in the levels of Cav2.2 or ASIC between subjects with and without CKD-aP. TRPA1, Nav1.8，and Kv1.4 were not expressed. Conclusions: It was concluded that this greater difference in expression of ion channels at the skin tissue including specific for cutaneous peripheral nerve endings in CKD patients with CKD-aP may increase generator potential related to itching.

Though the energy density of lithium-ion batteries continues to increase, safety issues related with the internal short-circuit and the resulting combustion of highly flammable electrolyte impede the further development of lithium-ion batteries. It has been well-accepted that a thermal stable separator is important to postpone the entire battery short-circuit and thermal-runaway. Traditional methods to improve the thermal stability of separators includes surface modification and/or developing alternate material systems for separators which may always affect the battery performance negatively. Herein, a thermostable and shrink-free separator with little compromise in battery performance is prepared by coaxial electrospinning and tested. The separator consists of core-shell fiber networks where poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) layer serves as shell and polyacrylonitrile (PAN) as the core. This core-shell fiber network exhibits little or even no shrinking/melting at elevated temperature over 250 °C. Meanwhile, it shows excellent electrolyte wettability and can take large amount of liquid electrolyte three times more than that of conventional Celgard 2400 separator. In addition, the half-cell using LiNi1/3Co1/3Mn1/3O2 as cathode and the aforementioned electrospun core-shell fiber network as separator demonstrates superior electrochemical behavior, stably cycling for 200 cycles at 1 C with a reversible capacity of 130 mAh g-1 and little capacity decay.

In the article, the fireball formed in the collision of relativistic nuclei is considered as a quantum object. Based on this, an attempt is made to explain the difference in the measurements of hyperon yields in the two experiments - NA49 and NA57. Using the basic principles of quantum mechanics, it was shown that a fireball can have two quantum states - with and without ignited Quark-Gluon Plasma (QGP). With an increase of the collision energy of heavy ions, the probability of QGP ignition increases. At the same time, the probability of the formation of fireball without QGP ignition also remains nonzero even at nuclear collision energies that are much higher than the threshold QGP formation energy, which may be erroneously considered to be fixed and which is intensively sought in modern heavy ion accelerators. Thus, at SPS energy of heavy ion collisions \sqrt{s_{NN}} = 17.3 GeV, which is much higher than the assumed threshold energy of QGP formation in the region around or slightly above of \sqrt{s_{NN}} = 3 GeV, only half of the central collisions of heavy ions bring to the formation of a fireball consisted of deconfined matter (quarks and gluons), the remaining half of the collisions lead to the formation of a fireball from only hadronic matter (mesons, nucleons, hyperons etc.).

It is shown that the termination of the channeling of the fundamental radiation mode in the waveguide can be observed upon heating of an optical integrated circuit based on proton exchange channel waveguides formed in a lithium niobate single crystal. This process is reversible, but restoration of waveguide performance takes tens of minutes. The effect of the waveguide disappearance is observed upon rapid heating (5 °C/min) from a low temperature (minus 40 °C). This effect can lead to a temporary failure of navigation systems using fiber optic gyroscopes with modulators based on a lithium niobate crystal

Leucokinins (LKs) constitute a family of neuropeptides identified in numerous insects and many other invertebrates. The LKs act on G-protein coupled receptors that display only distant relations to other known receptors. In adult Drosophila, 26 neurons/neurosecretory cells of three main types express LK. The four brain interneurons are of two types, and these are implicated in several important functions in the fly’s behavior and physiology, including feeding, sleep-metabolism interactions, state-dependent memory formation, as well as modulation of gustatory sensitivity and nociception. The 22 neurosecretory cells (ABLKs) of the abdominal neuromeres coexpress LK and a diuretic hormone (DH44), and together these regulate water and ion homeostasis and associated stress, as well as food intake. In Drosophila larvae, LK neurons modulate locomotion, escape responses, and aspects of ecdysis behavior. A set of lateral neurosecretory cells, ALKs, in the brain express LK in larvae, but inconsistently so in adults. These ALKs coexpress three other neuropeptides and regulate water and ion homeostasis, feeding and drinking, but the specific role of LK is not yet known. This review summarizes Drosophila data on embryonic lineages of LK neurons, functional roles of individual LK neuron types, interactions with other peptidergic systems, and orchestrating functions of LK.

Expression levels of Cav3.2, BKCa, and anoctamin 1 were previously found to be significantly elevated in patients with chronic kidney disease–associated pruritus (CKD-aP). On the other hand, the expression of TRPV1 was significantly reduced. We further compared CKD patients with and without CKD-aP in terms of the expression levels of several ion channels in the skin, including in peripheral nerve endings。Based on CKD-aP severity, subjects were divided into two groups: non-CKD-aP (no or slight pruritus; n = 16) and CKD-aP (mild, moderate, or severe pruritus; n = 16). Skin samples were obtained from the forearm or elbow during arteriovenous fistula surgery. We used quantitative real-time polymerase chain reaction to measure the skin expression levels of the following ion channels in the skin: Nav1.7, Kv7.2, TREK1, HCN2, TrkA, and Piezo2.　RT-PCR analyses showed that CKD-aP patients had significantly higher levels of TREK1 and Piezo2 transcripts and significantly lower levels of HCN2 transcripts than non–CKD-aP patients. No significant differences were noted between groups in the expression of Nav1.7 or TrkA. Moreover, Kv7.2 transcripts were not detected in either group. In skin samples collected from CKD-aP patients, ion channel expression patterns were altered to enhance hyperpolarization of pruriceptive neurons.

Penicillium digitatum is the major postharvest pathogen of citrus fruit under Mediterranean climate conditions. In the present work, we have addressed the study of the role of P. digitatum’s proteases in virulence following two complementary approaches. In a first approach, we have undertaken the functional characterization of the P. digitatum prtT gene, which codes for a transcription factor previously shown to regulate extracellular proteases in other filamentous fungi. Deletion of prtT caused a significant loss in secreted protease activity during in vitro growth assays. However, there was no effect on virulence. Gene expression of the two major secreted acid proteases was barely affected in the ΔprtT deletant during infection of citrus fruit. Hence, no conclusion could be drawn on the role of these secreted acidic proteases on the virulence of P. digitatum. In a second approach, we have studied the effect of different protease inhibitors and chelators in virulence. Co-inoculation of citrus fruit with P. digitatum conidia and a cocktail of protease inhibitors resulted in almost a complete absence of disease development. Analysis of individual inhibitors revealed that the metalloprotease inhibitor 1,10-phenanthroline was responsible for the observed effect. The application of metal ions reverted the protective effect caused by the metallopeptidase inhibitor. These results may set the basis for the development of new alternative treatments to combat this important postharvest pathogen.

This work explores the use of Kuhn verdazyl radicals as building blocks in multifunctional molecular materials in an exemplary study, focusing on the magnetic and the electron transfer (ET) characteristics, but also addressing the question whether chemical modification by cross-coupling is possible. The ET in solution is studied spectroscopically whereas solid state measurements afford information about the magnetic susceptibility or the conductivity of the given samples. The observed results are rationalized based on the chemical structures of the molecules, which have been obtained by X-ray crystallography. The crystallographically observed molecular structures as well as the interpretation based on the spectroscopic and physical measurements are backed up by DFT calculations. The measurements indicate that only weak, antiferromagnetic coupling is observed in Kuhn verdazyls owed to the low tendency to form face-to-face stacks, but also that steric reasons alone are not sufficient to explain this behavior. Furthermore, it is also demonstrated that ET reactions proceed rapidly in verdazyls/verdazylium redox couples and that Kuhn verdazyls are suited as donor molecules in ET reactions.

There is an urgent demand worldwide for the development of highly selective adsorbents and sensors of heavy metal ions and other organic pollutants. Within these environmental and public health frameworks, we are combining the salient features of clays and chelatant polymers to design selective metal ion adsorbents. Towards this end, the ion imprinting approach has been used to develop a novel nanohybrid material for the selective separation of Cu2+ ions in aqueous solution. The Cu2+-imprinted polymer/ montmorillonite nanocomposite (IIP/Mt) and non-imprinted polymer/montmorillonite nanocomposite (NIP/Mt) were prepared by radical photopolymerization process in the visible light. Ion imprinting was indeed important as the recognition of copper ions by IIP/Mt was significantly superior to that of NIP/Mt that is the nanocomposite synthesized in the same way but in the absence of Cu2+ ions. The adsorption process as batch study was investigated under the experimental condition affecting same parameters such as contact time, concentration of ions metals and pH. The adsorption capacity of Cu2+ ions is maximized at pH 5. Removal of Cu2+ ion achieved equilibrium within 15 minutes; the results obtained were found to be fitted by the pseudo-second order kinetics model. The equilibrium process was well described by the Langmuir isothermal model and the maximum adsorption capacity was found to be 23.6 mg/g.

The state of charge estimation is an important part of the battery management system, the estimation accuracy of which seriously affects the working performance of the lithium ion battery pack. The unscented Kalman filter algorithm has been developed and applied to the iterative calculation process. When it is used to estimate the SOC value, there is a rounding error in the numerical calculation. When the sigma point is sampled in the next round, an imaginary number appears, resulting in the estimation failure. In order to improve the estimation accuracy, an improved adaptive square root - unscented Kalman filter method is introduced which combines the QR decomposition in the calculation process. Meanwhile, an adaptive noise covariance matching method is implied. Experiments show that the proposed method can guarantee the semi-positive and numerical stability of the state covariance, and the estimation accuracy can reach the third-order precision. The error remains about 1.60% under the condition of drastic voltage and current changes. The conclusion of this experiment can provide a theoretical basis of the state of charge estimation in the battery management of the lithium ion battery pack.

The aim of this study is to empirically examine the link between foreign direct investment (FDI) and domestic investment (DI) in South Africa over the period of 41 years (1975-2016). Accurately, it attempts to determine whether FDI crowds in or crowds out DI in South Africa. DI is sub-divided into private domestic investment (credit to domestic private sector) and public corporation investment (state owned enterprises). We used the Autoregressive Distributed Lag-Error Correction Model (ARDL-ECM) technique to ascertain long run and short run effects concurrently after establishing that the variables were stationary (using the PP test). The results of the unit root test shows that all variables are integrated of order zero I(0) or integrated of order one I(1), indicating that the series of variables are stationary in the level or first difference form. The findings revealed that variables are cointegrated in the long run. The ARDL model found a negative link between FDI and domestic investment. The result implies that FDI crowds out domestic investment. Moreover, the long run estimate revealed that domestic investment is crowded in by government investment expenditure (GINV). Other findings uncovered that, GDP crowds out private domestic investment while crowding in public corporation investment. Moreover, the long run estimate revealed that domestic investment is crowded in by gross domestic savings (SAV). On the other hand, the real exchange rate (EXCR) crowds out private domestic investment while crowding in public corporation investment. Trade openness (TRA) crowds out domestic investment. Additionally, the short run estimate uncovered that private domestic investment is crowded out by FDI, EXCR, and TRA whereas GINV, GDP and SAV is crowding in private domestic investment. Other findings discovered that, in the short run, public corporation investment is crowded out by FDI, GDP, EXCR and TRA, while GINV and SAV crowd in public corporation investment. The CUSUM confirms that the models are structurally firmness.

The remaining capacity can only be measured with offline method. This brings great challenge for the online prediction of Li-ion battery’s RUL. A novel online prediction method for Li-ion battery’s RUL was proposed, which is based on multiple health indicators (HIs) and can be derived from the batteries’ historical operation data. Firstly, four indirect HIs were built according to the battery’s operation current, voltage and temperature data respectively. On that basis, a generalized regression neural network (GRNN) was developed to estimate the battery’s remaining capacity, and the non-linear autoregressive approach (NAR) was utilized to predict the battery’s RUL based on the estimated capacity value. Furthermore, to reduce the interference, twice wavelet denoising were performed with different thresholds. A case study is conducted with a NASA battery dataset to demonstrate the effectiveness of the method. The result shows that the proposed method can obtain Li-ion batteries’ RUL effectively.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

A new generation of nano-technologies is expanding solid propulsion capabilities and increasing their relevance for versatile and manoeuvrable micro-satellites with safe high-performance propulsion. We propose the innovative concept, connected with application of new synergistic effect of the energetic materials performance enhancement and reaction zones programming for the next generation small satellite multimode solid propulsion system. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon, by the properties of the energetic materials reaction zones and by localization of the energy release areas. This synergistic effect can be provided through application of the functionalized carbon-based nanostructured metamaterials as a nano-additives along with simultaneous manipulating by their properties through the electrostatic field. Mentioned effect will be controlled through predictive programming both by the spatial structure and physics-chemical properties of the functionalized carbon-based nano-additives and through the electromagnetic control of the self-organized wave pattern excitation and micro- and nano- scale oscillatory networks in the energetic material reaction zones. Suggested new concept makes it possible to increase the energetic material regression rate and increase the thrust of the solid propulsion system with minimal additional energy consumption.

Voltage-gated Ca²⁺ (Ca_v) channels play pivotal roles in regulating gene transcription, neuronal excitability, and neurotransmitter release. In order to meet the spatial and temporal demands of visual signaling, Ca_v channels exhibit unusual properties in the retina compared to their counterparts in other areas of the nervous system. Here, we review current concepts regarding the specific subtypes of Ca_v channels expressed in the retina, their intrinsic properties and forms of modulation, and how their dysregulation could lead to retinal disease.

Structural self-organizing and pattern formation are universal and key phenomena observed during growth and cluster-assembling of the carbyne-enriched nanostructured metamaterials at the ion-assisted pulse-plasma deposition. Fine tuning these universal phenomena opens access to designing the properties of the growing carbyne-enriched nano-matrix. The structure of bonds in the grown carbyne-enriched nano-matrices can be programmed by the processes of self-organization and auto-synchronization of nanostructures. We propose the innovative concept, connected with application of the universal Cymatics phenomena during the predictive growth of the carbyne-enriched nanostructured metamaterials. We also propose the self-organization approach for increase stability of the long linear carbon chains. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon and their distribution by the spatial structure and properties of the nanostructured metamaterial grows region through the new synergistic effect. Mentioned effect will be provided through the vibration-assisted self-organized wave patterns excitation along with simultaneous manipulating by their properties through the electric field. We propose to use acoustic activation of the plasma zone of nano-matrix growing. Interaction between the inhomogeneous electric field distribution generated on the vibrating layer and the plasma ions will serve as the additional energizing factor controlling the local pattern formation and self-organizing of the nano-structures. Suggested concept makes it possible to provide precise predictive designing the spatial structure and properties of the advanced carbyne-enriched nanostructured metamaterials.

Breast cancer is a complex and heterogeneous disease that displays diverse molecular subtypes and clinical outcomes. Although it is known that the location of tumors can affect their biological behavior, the underlying mechanisms are not fully understood. In our previous study, we found a differential methylation profile and membrane potential between left (L) and right (R)-sided breast tumors. In this current study, we aimed to identify the ion channels responsible for this phenomenon and determine any associated phenotypic features. To achieve this, experiments were conducted in mammary tumors in mice, human patient samples, and with data from public datasets. The results revealed that L-sided tumors have a more depolarized state than R-ones. We identified a 6-ion channel-gene signature (CACNA1C, CACNA2D2, CACNB2, KCNJ11, SCN3A, and SCN3B) associated with side: L-tumors exhibit lower expression levels than R-ones. Additionally, in silico analyses show that the signature correlates inversely with DNA methylation writers and with key biological processes involved in cancer progression, such as proliferation and stemness. The signature also correlates inversely with patients’ survival rates. In an in vivo mouse model, we confirmed that KI67 and CD44 markers were increased in L-sided tumors and similar tendency for KI67 was found in patient L-tumors. Overall, this study provides new insights into the potential impact of anatomical location on breast cancer biology and highlights the need for further investigation into possible differential treatment options.

Membranes based on sulfonated synditoactic polystyrene were thoroughly characterized by contrast variation SANS over a wide Q-range in dry and hydrated states. The film samples were prepared by solid-state sulfonation that allowed a uniform sulfonation of only the amorphous phase while preserving the crystallinity of the membrane. The samples were loaded with different guest molecules in either the amorphous (fullerenes) or the crystalline (toluene) regions, in order to vary the neutron contrast or to reproduce the conditions enabling an increased resistance of the membranes to chemical decomposition. The use of uni-axially deformed film samples and contrast variation with different H2O/D2O mixtures allowed for the identification and characterization of different structural levels with sizes between nm and μm, which form and evolve in the membrane morphology in dry and hydrated states and produce scattering features on different detection sectors and at different detection distances after the sample, depending on their size and orientation.

Global warming and climate change have led to extreme changes in climatic conditions in recent years. The Taiwan government designates the construction of the Kinmen County as low carbon islands, to promote the operation of 100 electric motorcycles and battery demonstration. This study combined with island tourism, after boarding the island, visitors can rent electric motorcycles from the passenger service center and coordinate with the island tour map to show the location of the battery exchange points, so as to facilitate the search. During the operation, the amount of electric motorcycle lease is 15,551 times, the total mileage of motor vehicle is 284,404 km, the number of battery exchange is 622 times, the lease income is about NT$900,000. To reduce carbon and economic benefits of the assessment, compared to the motorcycles (50 c.c), electric motorcycles (EM 100) can reduce the carbon emissions by 8,726 kg, reducing energy costs of NT$422,594.

Restricted feeding is well known to affect expression profiles of both clock and metabolic genes. However, it is unknown whether these changes in metabolic gene expression result from changes in the molecular clock or in feeding behavior. Here we eliminated the daily rhythm in feeding behavior by providing 6-meals evenly distributed over the light/dark-cycle. Animals on this 6-meals-a-day feeding schedule retained the normal day/night difference in physiological parameters including body temperature and locomotor activity. The daily rhythm in respiratory exchange ratio (RER), however, was significantly phase-shifted through increased utilization of carbohydrates during the light phase and increased lipid oxidation during the dark phase. This 6-meals-a-day feeding schedule did not have a major impact on the clock gene expression rhythms in the master clock but did have mild effects on peripheral clocks. By contrast, genes involved in glucose and lipid metabolism showed differential expression. Concluding, eliminating the daily rhythm in feeding behavior in rats does not affect the master clock and only mildly affects peripheral clocks, but disturbs metabolic rhythms in liver, skeletal muscle and brown adipose tissue in a tissue-dependent manner. Thereby a clear daily rhythm in feeding behavior strongly regulates timing of peripheral metabolism, separately from circadian clocks.

We report a self-assembly synthesis of silicon nanoparticles/nitrogen-doped reduced graphene oxide/ carbon nanofiber (Si@N-doped rGO/CNF) composites as potential high-performance anodes for rechargeable lithium-ion batteries (LIB) through the electrostatic attraction between amino and carboxyl groups. Nitrogen atoms generate a large number of vacancies or defects on the graphite plane, providing additional transmission channels for the diffusion of lithium ions, and improving the conductivity of the electrode. Carbon nanofiber (CNF) can help maintain the stability of the electrode structure and prevent silicon nanoparticles from falling off the electrode, prevent silicon nanoparticles from being directly exposed to the electrolyte, and can form a stable solid electrolyte interface (SEI) film. The three-dimensional conductive structure composed of Si, nitrogen atom-doped reduced graphene oxide (N-doped rGO), and CNF can effectively buffer the volume changes of silicon nanoparticles, shorten the transmission distance of lithium ions (Li+) and electrons, and make the electrode have good conductivity and stability in mechanical properties. In addition, compared with the Si@N-doped rGO and Si/rGO/CNF composite electrode, the Si@N-doped rGO/CNF composite electrode shows good cycle performance and rate capability, and its reversible specific capacity can reach 1418.8 mAh/g. The capacity retention rate is 64.7%, and the coulomb efficiency is 95%.