P. palmata is a viable source of nutrients with bioactive properties. The present study determined the potential role of post-extraction ultrasonication on some compositional features and antioxidant properties of resulting extracts after sequential enzymatic/alkaline treatment. No significant difference was detected in terms of protein content and recovery as well as amino acid composition of the extracts. The nitrogen-to-protein conversion factor of 5 was found to be too high for the seaweed and its enzymatic/alkaline extracts. The extracts sonicated by bath for 10 minutes and not sonicated showed the highest and lowest total phenolic contents (p<0.05), respectively. The highest radical scavenging and lowest metal chelating activities were observed for the non-sonicated sample, as evidenced by IC50 values. The extract sonicated by bath for 10 minutes showed the most favorable in vitro antioxidant properties since its radical scavenging was not significantly different from that of not sonicated sample (p>0.05), whereas its metal chelating activity was significantly higher (p<0.05). To conclude, post-extraction ultrasonication by an ultrasonic bath for 10 minutes is recommended to increase phenolic content and improve antioxidant properties of enzymatic-alkaline extracts from P. palmata.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

A cuprous oxide (Cu₂O) thin layer served as the base for a non-enzymatic glucose sensor in an alkaline medium, 0.1 NaOH solution, with a linear range of 50-200 mg/dL using differential pulse voltammetry (DPV) measurement. An X-ray photoelectron spectroscopy (XPS) study confirmed the formation of the cuprous oxide layer on the thin gold film sensor prototype. Quantitative detection of glucose in both phosphate-buffered saline (PBS) and undiluted human serum were carried out. Neither ascorbic acid nor uric acid even at a relatively high concentration level of 100mg/dL in serum interfered with the glucose detection, demonstrating the excellent selectivity of this non-enzymatic cuprous oxide thin layer based glucose sensor. Chronoamperometry (CA) and single potential amperometric voltammetry were used to verify the measurements obtained by differential pulse voltammetry (DPV), and the positive results validated that the detection of glucose in a 0.1 M NaOH alkaline medium by DPV measurement was effective. Nickel, platinum and copper are commonly used metals for non-enzymatic glucose detection. The performance of these metal-based sensors for glucose detection using DPV were also evaluated. Cuprous oxide (Cu₂O) thin layer based sensor showed the best sensitivity for glucose detection among the sensors evaluated.

This study delves into the extraction and compositional analysis of soybean meal protein isolates (SMPI) compared to soy protein isolates (SPI), focusing on their functional and structural properties, digestibility, amino acid composition, and the impact of various proteases on antinutritional factors. By leveraging alkaline (0.25 % of NH4OH) extraction and isoelectric precipitation, SMPI was efficiently obtained. Compositional characteristics revealed that SMPI has high moisture, protein, and ash, but lower fat, and carbohydrate content compared to SPI. Alcalase, Neutrase and Pepsin hydrolysis indicated lower digestibility of SMPI than SPI. Fourier-transform infrared spectroscopy and sodium dodecyl sulfate-polyacrylamide gel electrophoresis provided similar molecular structure and protein molecular weight distribution. This comprehensive analysis underscores the valorization of soybean meal, promoting its use beyond conventional animal feed towards nutritional supplements and bio-based products, thereby contributing to environmental sustainability and the enhancement of global food systems.

The global textile sector, pivotal to economic development, significantly contributes to environmental degradation, prompting a shift towards sustainable raw material sources. Embracing circular economy principles, this industry is exploring the valorization of agricultural by-products. This study introduces an innovative approach to repurposing mango waste into valuable textile fibers, a byproduct of the fruit processing industry, predominantly generated during juice and jam production. The focus is on the lignocellulosic constituents of mango waste, specifically the peel, seed, and fibrous material, traditionally considered as refuse. Previous research has predominantly utilized mango peel in pectin extraction for food applications, whereas the potential of seed and fibrous content remains underexplored. This investigation endeavors to transform these fibrous by-products into high-value materials suitable for textile manufacturing. The process involved washing, drying, and comprehensive physicochemical characterization of mango fibers, emphasizing lignin quantification, revealing a composition of 12.2% lignin. An experimental design was employed to elucidate the impact of variables such as liquid-to-solid ratio, reaction duration, and sodium hydroxide concentration on lignin dissolution through alkaline hydrolysis. Optimal conditions—10% NaOH concentration, 30 mL/g liquid-to-solid ratio over six hours—achieved an 83% reduction in lignin content. The resulting fibers exhibited properties akin to conventional natural fibers, including a favorable aspect ratio indicative of their suitability for textile applications. A subsequent softening process using propylene glycol enhanced the fibers' spinability, producing a durable, textured fabric ideal for eco-conscious fashion applications, including bags, footwear, and accessories. This research demonstrates the feasibility of converting mango waste into a textile-worthy material and underscores the importance of waste revalorization in promoting sustainability within the circular economy framework.

Malnutrition problems are related to diets that lack one or more essential elements, which it is extremely important to food enrichment to improve the content of compounds effective for health. The objective of this study is to evaluate the effect of the addition of Ca2+, K+ and Mg2+ on the induction of nutraceutical quality in grafted tomatoes grown in the NFT (Nutrient Film Technique) system. In the experiment, two factors were evaluated: plants with and without grafting and the foliar application of 10 ml L−1 Ca2+, 4 ml L−1 K+ and 10 ml L−1 Mg2+ cations separately for each case, in addition to the control. The treatments were evaluated using a completely randomized design, with 5 repetitions per treatment. The interactive effects between grafting and foliar application of Ca2+ induced a greater content lycopene, β-carotene and total flavonoids in fruits of tomato. The interactive effects between the graft and the Mg2+ foliar applications obtained the best results in the phenol content. As regards, capacity DPPH and ABTS, the graft decreased concentration, increasing the content of these through foliar applications of calcium. Regarding the enzymatic variables, graft factor increased activity catalase, glutathione peroxidase and phenylalanine ammonium lyase, obtained the best results graft interaction and foliar application of calcium and magnesium. The results obtained demonstrate the influence of the use of grafts and foliar applications of cal-cium and magnesium as tools that could improve the nutraceutical quality content of tomato crop

Abstract: The present work evaluates the feasibility of using volcanic fly ash (VFA), generated by the eruption of the Tajogaite volcano on the island of La Palma (Spain) in 2021, as a precursor in the preparation of cementitious materials with different Portland cement (PC) replacement levels (0%, 30%, 70% and 100%), in the absence (Blended Cement, BC) and presence of an alkaline ac-tivator (Hybrid Alkaline Cement, HAC, and Alkaline Cements, AC). Hydration kinetics (isother-mal conduction calorimetry), paste mechanical strengths and reaction products were character-ised by XRD, FTIR, TG/DTG and BSEM/EDX. The results obtained indicate that the strengths de-veloped by the hybrid alkaline cements (HAC) are higher than those of the blended cements (BC), especially at the age of 2 days, where 25 MPa was obtained with the replacement of 70% PC by VFA. Alkaline cements (AC, 100% VFA) prepared with 8M NaOH solution as activator reached 40 MPa after 2 days. It was observed that in all the binders, depending on the initial composition of the binder mixture and the percentage of replacement and/or activator, VFA reacts to form cementitious gels, C-A-S-H and N-A-S-H type, which supports its use as a mineral addition to blended cement or as a precursor in the preparation of alkaline and hybrid alkaline cements.

Background and Aim: Serum alkaline phosphatase (ALP) activity has been associated with ath-erosclerotic cardiovascular disease (ASCVD). We aimed to investigate the association of ALP with ASCVD in patients with dyslipidemia. Methods: Retrospective cohort study including consecutive adults with dyslipidemia followed-up for ≥3 years (from 1999 to 2022) in the outpatient Lipid Clinic of Ioannina University General Hospital, Greece. The primary endpoint was the association between baseline ALP and incident ASCVD after adjusting for traditional risk factors (i.e. sex, age, hypertension, diabetes, smoking, dyslipidemia), baseline ASCVD and lipid-lowering treatment. ALP levels were stratified by ter-tiles as follows: low:<67 U/L, middle: 67-79 U/L, high: ≥79 U/L. Results: Overall, 1178 subjects were included; 44% were males and their median age was 57 years (range 49-65). During a 6-year median follow-up (interquartile range IQR: 4-9), 78 new ASCVD events (6.6%) occurred. A statistically significant association between baseline ALP levels and incident ASCVD was demonstrated (Odds Ratio, OR: 6.99, 95% Confidence Interval, CI: 2.29-21.03, p=0.001). Subjects in the highest ALP tertile had the highest odds for ASCVD when compared with those in the lowest tertile (OR: 2.35; 95% CI: 1.24-4.41, p=0.008). Conclusions: The present study demonstrated that ALP is associated with ASCVD development in patients with dyslipidemia.

Polyglycerols (PGs) are biocompatible and highly functional polyols with a wide range of applications, such as emulsifiers, stabilizers, antimicrobial agents, in many industries including cosmetics, food, plastic and biomedical. The demand increase for biobased PGs encourages researchers to develop new catalytic systems for glycerol polymerization. This review focuses on alkaline homogeneous and heterogeneous catalysts. The performances of the alkaline catalysts are compared in terms of conversion and selectivity, and their respective advantages and disadvantages are commented. While homogeneous catalysts exhibit a high catalytic activity, they cannot be recycled and reused, whereas solid catalysts can be partially recycled. The key issue for heterogenous catalytic systems, which is unsolved so far, is linked to their instability due to partial dissolution in the reaction medium. Further, this paper also reviews the proposed mechanisms of glycerol polymerization over alkaline-based catalysts and discuss the various operating conditions with an impact on the performances. More particularly, temperature and amount of catalyst proved to have a significant influence on glycerol conversion and on its polymerization extent.

The study addresses the management of kitchen waste by transforming it into biofertilizer formulations utilizing an effective in-house developed multi-enzyme preparation. A separate hydrolysis and fermentation bioprocessing approach which in particular relates to the application of a separate enzyme preparation from Aspergillus niger P-19 to separately hydrolyze kitchen waste, followed by the growth of Klebsiella pneumoniae AP-407 in the liquid hydrolysate as well with simultaneous production of carrier-based biofertilizer. In liquid and carrier-based biofertilizers, the viable cell count reaches 3.00 × 1012 CFU/ml and 3.00 × 1012 CFU/g, respectively. The current study adopts a novel process technique for the manufacturing of both carrier and liquid biofertilizers, adopting a zero-waste approach to the management of kitchen waste.

Indole and indole-3-lactate are known dominant microbial tryptophan catabolites (MICT). In obesity, the fecal indole concentration corresponds to the normal one, and that of indole-3-lactate significantly decreases along with other MICT, while it increases in blood plasma. During the analysis of the «enzymatic landscape» of the intestinal microbiota we find an almost twofold increase in the correlation between the concentrations of fecal MICT and the «enzymatic landscape», with indole-3-lactate having the closest relationships with the “enzymatic landscape” of all MICT. Here, we report statistically significant correlations of indole-3-lactate and the gut microbial enzymes for fructose, amino sugars, nucleotides, polyamines metabolism, and sulfoglycolysis. We also demonstrate that indole-3-lactate producing microbiota representatives increase three-fold in obesity. The phenotype of the microbiotic population is thus represented by completely different genera and species of microorganisms in obese individuals compared to healthy donors.

Natural fibers are a gift from nature that we yet fully utilized until now. It can be classified into several groups and bast fibers are the group having the most promising performance when reinforced in polymer composites. However, numerous factors have been reported that influences mechanical properties of fiber reinforcements in the composite. In this review, bast fiber retting process and the effect of enzymatic retting on fiber and fibers reinforced polymer composites have been discussed and reviewed for the latest researches. Retting precedes mechanical processing (i.e. scutching) of the fiber from the stem and is essential for reduction of fiber breakage. All retting methods except chemical retting process are involving secretes of enzymes by bacteria or fungi under controlled (enzymatic retting) or random conditions (water and dew retting). Besides, enzymatic retting is claimed to have more environmentally friendly wastewater products, shorter retting period and controllable fiber biochemical components under mild incubation conditions. This review comprehensively assesses the enzymatic retting process for producing high-quality bast fiber and will become a reference for future development on bast fiber reinforced polymer composites.

In Ecuador, particularly in the El Oro province, gold mining has been historically hampered by arsenic contamination in the ores. This research addresses the persistent issue of arsenic in gold-bearing ores from Miraflores Mine in Cerro Azul, Atahualpa Canton, and the challenges it presents to mining operations. The study's purpose is to evaluate the effectiveness of an alkaline leaching process for arsenic removal. The ore underwent thorough characterisation, employing advanced techniques like fire assay and atomic absorption. Once the ore's nature was discerned, an arsenic extraction experiment using a leaching solution was conducted. The implemented process achieved an arsenic removal efficiency of 90.54%. This enhanced ore quality facilitates efficient metallurgical applications and, more notably, reduces the environmental footprint by diminishing the need for harmful reagents like sodium cyanide. However, a significant implication of this method is the added cost due to the need for heat during the leaching test, amounting to an approximate $30 per ton increase. The alkaline leaching process emerges as a promising solution for arsenic challenges in El Oro’s mining sector. While the findings are encouraging, further expansive tests are recommended to validate the results and underscore the urgency for sustainable and hazard-conscious mining practices.

Hydrogen energy is regarded as an auspicious future substitute to replace fossil fuels, because of its environmentally friendly characteristics and high energy density. In the pursuit of clean hydrogen production, there has been a significant focus on the advancement of effective electrocatalysts for the process of water splitting. Although noble metals like Pt, Ru, Pd and Ir are superb electrocatalysts for the hydrogen evolution reaction (HER), they have limitations for large-scale applications, mainly high cost and low abundance. As a result, non-precious transition metals have emerged as promising candidates to replace their more expensive counterparts in various applications. This review focuses on recently developed transition metal phosphides (TMPs) electrocatalysts for the HER in alkaline media due to the cooperative effect between the phosphorus and transition metals. Finally, we discuss the challenges of TMPs for HER.

Nowadays, the world's refractory gold ore production accounts for about 30% of the world's total gold, such gold concentrate leaching rate is low, seriously limiting the efficient use of gold resources. The alkaline preoxidation process can improve the leaching rate of this kind of gold deposit, and has a good development and application prospect. So, it is of great significance to study the oxidation and dissolution behavior of pyrite in alka-line environment. In this paper, the oxidation process of gold-bearing pyrite in alkaline electrolyte was studied by electrochemical techniques, and the oxidation products of pyrite electrode in alkaline solution were characterized by XPS，SEM and other analytical methods. The results show that the optimum pH for pyrite electrochemical oxidation dissolution is about 12, and oxidation potential of pyrite should be above 0.8 V. In that proces of alkaline oxidation dissolution of pyrite, part of S element enters the electrolyte in the form of Sx2-, S2O32-, SO32-and SO42-, and a small amount of S element is adsorbed on the surface of the electrode in the form of S0 and becomes a part of the passive layer. Fe element is adsorbed on the surface of electrode in the form of Fe(OH)2, Fe2O3 and Fe2(SO4)3, which becomes the main component of passivation layer. This study provides a theoretical basis and reference data for the chemical preoxidation treatment of sulfide ores.

The influence of humic aggregates in water solution upon the chemical stability under basic conditions of different substrates has been reviewed. The kinetic behavior of each substrate has been modelized in terms of micellar pseudophase model.

Plastics are naturally hydrophobic materials so, in order to employ flotation for the separation of plastic mixtures, the use of appropriate wetting agents is mandatory. In this work, the effect of pretreatment with alkaline solutions of sodium hydroxide on the floatability of four plastics (PET, PS, PMMA and PVC) was studied. The influence of NaOH concentration, treatment time and temperature of the alkaline solution, and influence of particle size was analyzed. Results showed that alkaline treatment had a strong effect on PET floatability, some effect on floatability of PMMA and PVC and no effect on floatability of PS. Plastics floatability decreased with the increase of NaOH concentration, temperature and treatment time of the alkaline solution. Based on flotation behavior of simple plastics, flotation separation after alkaline treatment of bi-component mixtures of PET with PS and PVC was achieved efficiently. The best separation was obtained for PET/PS mixture, a floated with a grade of 98% in PS and a sunk with a grade of 100% in PET. PET/PMMA mixture led to the worst separation. For PET/PMMA and PET/PVC mixtures, flotation separation improved with the decrease of the particles size.

X-ray crystallographic and theoretical charge density data for a series of compounds [(Co(Ts3tren))M(Co(Ts3tren))] (M = Mg, Ca, Sr and Ba) is examined. The crystal structures are isostructural and the alkaline earth metal ions have the same arrangement of donor oxygen atoms despite the large variation in ionic radii. The isomorphism of these molecules is surprising and a theoretical examination of the electronic structures, with the different metal ions along the series, provides detailed insight into their stabilities. The theoretical and experimental data are consistent and agree well. The local properties of the Co(II) ion and its donor atoms are relatively independent of the alkali earth metal.

Our target point within this following steps, is prostate cancer. Phosphatases are implicated in differents cell alterations, including proliferation, differentiation and carcinogenesis. In specific life circumstances, proteins are regulators with implications in intracellular signaling pathways. Alterations in phosphatases functionality represent a key point in malignancy development. We try within our description, to focus on an important process refering to dysregulation of phosphatase activity. More than, we will discuss therapeutic key points refering to compounds that inhibits phosphatase proteins with implications in carcinogenesis. So finally after folowing describtion steps, purposed aim is to conclude on prostate cancer and different key points abordation.

Nanocellulose has gained increasing attention during the past decade, which is related to its unique properties and wide application. In this paper, nanocellulose was produced by hydrolysis with ionic liquids (1-ethyl-3-methylimidazole acetate (EmimOAc) and 1-allyl-3-methylimidazolium chloride (AmimCl)) from microcrystalline cellulose (Avicel and Whatman) subjected to enzymatic pretreatment. The obtained material was characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), dynamic light scattering (DLS), scanning electron microscope (SEM) and thermogravimetric analysis (TG). The results showed that the nanocellulose had a regular and spherical structure with a diameter of 30-40 nm and exhibited lower crystallinity and thermal stability than the material after hydrolysis with Trichoderma reesei enzymes. However, the enzyme-pretreated Avicel had a particle size of about 200 nm and a cellulose II structure. A two-step process involving enzyme-pretreatment and hydrolysis with ionic liquids resulted in the production of nanocellulose. Moreover, the particle size of nanocellulose and its structure depend on the ionic liquid used.

In this paper, the effects of different food-grade enzymes on the antigenicity of casein (CN), β- lactoglobulin (β-LG) and ɑ-lactalbumin (ɑ-LA) in natural cow milk were studied. The degree of hydrolysis (DH), SDS-PAGE and molecular mas (MW) distribution of cow milk (CM) hydrolysates was assessed. Additionally, the residual antigenicity of CM hydrolysates was evaluated by using ELISA and western blotting with anti-CN, anti-β-LG and anti-ɑ-LA rabbit polyclonal antibody. The results showed that Alcalase and Protamex hydrolysis could efficiently reduce the antigenicity of CN, β-LG, ɑ-LA, showed a higher DH and the loss of density of CM proteins, as indicated by SDS-PAGE. The increasing of the low MW (<3 kDa) in CM hydrolysates was also presented. It was also found that Protamex, Alcalase could be more efficiently hydrolyzed major allergenic of CM than other enzymes for the development of hypoallergenic cow milk. Our research will lay a theoretical foundation for the study of hypoallergenic cow milk.

Ambitle in the Feni Island group is located at the southeastern end of the NW trending Ta-bar-Lihir-Tanga-Feni (TLTF) island chain, northeastern Papua New Guinea. This island chain is known for the presence of alkaline magmas, geothermal activity, copper-gold mineralization, and mining. The purpose of this study is to present and interpret the petrographic, mineralogical, and geochemical data of the subaerial volcanic rocks from Feni within the context of the tectonic evolution of the TLTF. The TLTF arc is a younger arc situated within the Greater Melanesian Arc, specifically the New Ireland Basin bounded by New Ireland and the extinct Kilinailau Trench. The formation of the TLTF is attributed to post-subduction extensional tectonics relating to the opening of the Manus Basin and the magma is potentially sourced from subduction-modified upper mantle. The main rock types sampled in this study are alkalic and include feldspath-oid-bearing basalt, trachybasalt, phonotephrite, trachyandesite, and trachydacite or quartz-trachyte. Minerals identified include forsteritic olivine, diopside, augite, andesine, anor-thitic plagioclase, nepheline and leucite in the primitive mafic suites whereas the more evolved intermediate and felsic hypabyssal suites contain amphibole, albite, orthoclase, biotite, and either rare quartz or feldspathoids. Amphibole composition is primarily magnesiohastingsite with minor pargasite formed under polybaric conditions. Accessory minerals include apatite, ti-tanite, and Ti-magnetite. Feni magmas are highly enriched in REEs relative to neighboring arcs. Fractional crystallization is the dominant process in the geochemical evolution of the Ambitle lavas. Pyroxene fractionation is dominant in the mafic lavas whereas hornblende fractionation is a major petrologic process within the intermediate suites proven by the presence of LREE enrichment and depletions in MREE and HREE.

The preservative qualities of individual ionic compounds on the infectivity of T4 virions were elucidated. T4 virions were immersed in quasi-pure ionic solutions prior to the adsorption process, and the pfu values of these were measured following the conventional method. In neutral ionic solutions, the minimum and the optimum concentrations for preservative qualities were corresponded with the results obtained from the multi-ionic media/buffers. In acid and alkali solutions, phages show tolerances at a pH range of 5-11 in multi-ionic media/buffers. T4 virions show no tolerance in quasi-pure acid, neutral and weak alkaline conditions. The preservative quality of T4 virions was jumped up in over 10-1 mM OH- solution, equivalent to pH value over 10, which is corresponding to the pKa of the deprotonation of the DNA bases G and T. Infectivity was lost below 10-1 mM OH- and higher than 10 mM OH-. These results implicate the maintaining of infectivity of a virion may need the flexibility of the intra-capsid DNA by deprotonation.

Parkia biglobosa (African locust bean) seed was fermented aerobically to produce a vegetable protein based condiment using various temperature differences and ambient temperature. The rate of fermentation was monitored using three (3) different methods namely: weight loss, pH and Carbon dioxide release. Samples were inoculated using Bacillus subtilis and Saccharomyces cerevisiae as starter culture. During fermentation, several changes occur in the seeds of the African Locust bean. The difference in the weight loss (initial and final weight of the fermenting samples) were used to monitor the rate of fermentation of the African Locust bean (parkia biglobosa) seeds to vegetable protein called ‘Iru’. Fermentation of this seed to ‘Iru’ is an alkaline fermentation, which was confirmed by this work. As means of monitoring the rate of fermentation, the evolution of CO₂ was also monitored.

A 17th century wall painting representing a Virgin between two Saints in a noble Italian renaissance palace, Palazzo Gallo in Bagnaia (Viterbo, Italy), was restored in 2021 in the context of a wider restoration campaign interesting the main room of the palace built by cardinal Sansoni Riario. Diagnostic analyses done with traditional characterization techniques (optical microscopy on micro-stratigraphic sections, X-ray fluorescence spectroscopy and Fourier transform infrared spectroscopy) provided the identification of both original painting and restoration materials, while imaging investigations as ultraviolet fluorescence photography, false color images and multispectral mapping provided by hypercolorimetric multispectral imaging (HMI) technique enabled the evaluation of the state of conservation, locating restoration interventions and supporting the monitoring of the cleaning procedure. An altered protective Paraloid-based coating dating from early 2000s had to be removed due to the unpleasant glossy finishing given to the painted surface, making the scene barely readable. To pursue a restoration protocol based on environmental sustainability and green chemistry, enzyme-based gels marketed by Nasier-Brenta© and CTS© companies were tested in different protocols for the cleaning of the mash covering the painting. Although some interesting results were observed, the enzymatic cleaning had a scarce effectiveness with timing beyond a reasonable interval. Traditional chemical solvents as Dowanol PM (methoxy-propanol) and benzyl alcohol were necessary to complete the cleaning of the painting surface.

We describe a competitive colorimetric assay that enables rapid and sensitive detection of galactose and reduced nicotinamide adenine dinucleotide (NADH) via colorimetric readouts and demon-strates its usefulness for monitoring NAD+-driven enzymatic reactions. We present a sensitive plasmonic sensing approach for assessing galactose concentration and the presence of NADH using galactose dehydrogenase immobilized gold nanostars (AuNS-PVP-GalDH). The AuNS-PVP-GalDH assay remains turquoise blue in the absence of galactose and NADH; however, as galactose and NADH concentrations grow, the reaction well color changes to a characteristic red color in the presence of an alkaline environment and metal ions catalyst (detection solution). As a result, when galactose is sensed in the presence of H2O2, the colored response of the AuNS-PVP-GalDH assay transforms from turquoise blue to light pink, then to wine red in a con-centration-dependent manner discernible to the human eye. This competitive AuNS-PVP-GalDH assay could be a viable analytical tool for rapid and convenient galactose quantification in re-source-limited areas.

In traditional oriental medicine, carrots (Daucus carota L.) are considered effective medicinal herbs; however, the use of D. carota leaves (DGL) as therapeutic agents has not been explored in depth. Therefore, we aimed to demonstrate the value of DGL, generally treated as waste while developing plants for wide industrial availability. Six flavone glycosides were isolated and identified from DGL, and their constituents were identified and quantitated using an NMR and HPLC/UV method, which was optimized and validated. The structure of chrysoeriol-7-rutinoside from DGL was elucidated for the first time. The method exhibited adequate relative standard deviation (&lt;1.89%) and recovery (94.89–105.97%). The deglycosylation of DGL flavone glycosides by Viscozyme L and Pectinex was assessed. Upon converting the reaction contents to percentages, the luteolin, apigenin, and chrysoeriol groups showed values of 85.8, 33.1, and 88.7%, respectively. The enzyme-treated DGL had a higher inhibitory effect on TNF-α and IL-2 expression than that of the carrot roots or carrot leaves without enzyme treatments. These results highlight the importance of carrot leaves and could be used as baseline standardization data for commercial development.

A study to produce cellulose nanofibrils (CNF) from Kraft cellulose pulp, an optimal enzyme mixture, was defined using a centroid simplex mixture design. The enzyme blend contains 69% endoglucanase and 31% exoglucanase. The central composite rotational design (CCRD) optimized the CNF production process by achieving a higher crystallinity index. It thus corresponded to a solid loading of 15 g/L and an enzyme loading of 0.974. Using the Segal formula, the crystallinity index (CrI) of CNF was determined by X-ray diffraction to be 80.87%. The average diameter of nanocellulose fibers measured by scanning electron microscopy between 550 - 600 nm for the CNF prepared by enzymatic hydrolysis and between 250 - 300 nm for the CNF produced by enzymatic hydrolysis with the optimal enzyme mixture followed by ultrasonic dispersion. Finally, synergistic interactions between the enzymes involved in nanocellulose production were demonstrated, with Colby factor values greater than one.

Polysaccharide-based edible coatings are served as an attractive preservation method for postharvest maintenance of most fruits. The current study examined the effect of carboxymethylcellulose (CMC)- and pectin (Pec)- based edible coatings on weight loss, firmness, total soluble solids (TSS), pH¬, titratable acidity (TA), vitamin C (vit C), total phenolics, anthocyanin and flavonoid contents, total antioxidant capacity (based on DPPH) and the activities of peroxidase (POD), polyphenol oxidase (PPO) and polygalacturonase (PG) enzymes during cold storage. The results showed that each coating and their combinations caused positive effects in all measured parameters except weight loss. The applied coatings preserved firmness and improved total phenols, anthocyanin and flavonoid contents, antioxidant capacity and POD activity. In addition, the coatings retarded TSS and pH enhancement and TA and vit C loss and decreased PPO and PG activities. It could be stated that CMC at 1 % and Pec at 1.5 % separately demonstrated the best results at most measured parameters; and among the combinations 0.5 % Pec + 1.5 % CMC acted better than the other treatments. Henceforth, application of CMC and/or Pec and/or their combinations would be considered as favorable approaches to improve postharvest quality characteristics of plum fruit.

Scarcity of water is one of the most serious concerns in plant biology with diverse implications at all the levels of molecular, biochemical, and physiological phenomena of plant growth, development, and consequently the productivity. Most of the strategies to induce or enhance drought tolerance in plants are unreasonably expensive and/or time-consuming. Some studies conducted in the recent past have shown that plant growth regulators (PGRs) may induce/improve physiological tolerance in plants to cope with adverse environmental conditions including drought. The present study was aimed at investigating the effects of foliar spray of GABA (0, 1, 2, and 4 mM) applied 20 days following the germination of seeds, on vegetative growth, morphological characteristics, integrity of cell-membrane, and the levels of photosynthetic pigments and enzymatic antioxidants in carrot cvs. Supertaj and Bharat, grown under 100% and 50% field capacity of soil moisture. The treated and untreated (control) carrot plants were harvested and analyzed 2 weeks following the GABA application. The results revealed that foliar application of GABA improved the vegetative growth and significantly increased the levels of free amino acids, plastid pigments, enzymatic antioxidants, and the relative water content in the root crop grown under 50% field capacity of soil moisture, compared to control. Additionally, the GABA application decreased the electrolyte leakage of ions and melondialdehyde (MDA) content in carrot leaves. The carrots harvested from GABA-treated or untreated (control) plants were not significantly different for their protein contents. In conclusion, the incorporation of GABA in the production management of carrots may help plants to mitigate the adverse effects of water deficit stress.

NiFe alloy nanoparticles/graphene oxide hybrid (NiFe/GO) was prepared for electrochemical glucose sensing. The as-prepared NiFe/GO hybrid was characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). The results indicated that NiFe alloy nanoparticles can be successfully deposited on GO. The electrochemical glucose sensing performance of the as-prepared NiFe/GO was studied by cyclic voltammetry and amperometric measurement. Results showed that NiFe/GO modified glassy carbon electrode had sensitivity of 173 μA mM⁻¹cm⁻² for glucose sensing with a linear range up to 5 mM, which was superior to commonly used Ni nanoparticles. Furthermore, high selectivity for glucose detection can be achieved by NiFe/GO. All the results demonstrated that NiFe/GO hybrid was promising for using in electrochemical glucose sensing.

A marine fibrinolytic compound FGFC1 enhancing fibrinolysis was obtained involving in enzymatic kinetic parameters of reciprocal activation system with single chain urokinase type plasminogen activator and plasminogen. FGFC1, a kind of bisindole alkaloid from a metabolite of rare marine fungi Starchbotrys longispora FG216, modulated enzymatic kinetic parameters including fibrinolytic reaction rate and fibrin degradation characteristics. The enzymatic kinetics of fibrinolysis was described based on enzymatic reaction of chromogenic-substrate associated with p-nitroaniline (p-NA). While single chain urokinase-type plasminogen activator (pro-uPA) actived plasminogen, K_cat and k_cat/k_m increased significantly with increase of FGFC1 concentration. Moreover, K_cat and k_cat/k_m exhibited 26.5-fold and 22.8-fold enhanced activity at the concentration of 40 μg•mL⁻¹ of FGFC1, respectively. The results suggested that FGFC1 improved significantly the maximum catalytic efficiency and the total catalytic activity of fibrinolysis base on the reciprocal activation of pro-uPA and plasminogen. K_m increased with increasing FGFC1 concentration, which indicated that FGFC1 decreased slightly the affinity activity of pro-uPA and plasminogen versus enzyme substrate. The marine bisindole alkaloid FGFC1 enhanced fibrinolysis which was taken on enzymatic kinetic characteristics.

Saline-alkaline aquaculture has become important breakthrough to expand available space for aquaculture in China. However, the biochemical composition and quality of Eriocheir sinensis reared in carbonate alkalinity water are still unclear. Therefore, this study investigated the edible yield, coloration, nutritional and flavor quality of Eriocheir sinensis. Significantly lower gona-dosomatic index (GSI) and meat yield (MY) were detected in intensive pond (IP) than those in semi intensive reed wetland (SIWR) (P< 0.05). Six color parameters differed between IP and SIRW in the hepatopancreas (P< 0.05). The contents of crude protein and fat in the female hepatopan-creas of IP were significantly higher than those in SIRW(P< 0.05). The higher concentrations of ∑MUFA, ∑EFA, h/H in the female edible tissues were checked in IP than those in SIRW, with significant difference including ∑MUFA in the hepatopancreas and ovary, ∑EFA in the muscle, and h/H in the ovary (P<0.05). Better total free amino acid (∑FAA) contents of muscle were de-tected in SIRW than that in IP. Significantly increasing tendency was detected in K, Ca, Mg, Fe, Zn of ovary from SIRW to IP (P< 0.05). Overall, the Eriocheir sinensis reared in carbonate alkalinity water is an important source of nutrient.

The basic hydrolysis of Malachite Green in the presence of β-Cyclodextrin has been studied and a catalytic effect has been found. Indeed, this basic hydrolysis is catalyzed by the interaction of deprotonated cyclodextrin hydroxyl group with the carbocation in the host-guest complex. This behavior is like the hydrolysis of Cristal Violet in the same reaction media.

(1) Infective endocarditis is a severe inflammatory disease associated with substantial mortality and morbidity. Alkaline phosphatase (AP) levels have been shown to change significantly during sepsis additionally we previously found higher initial AP drop after cardiac surgery is associat-ed with unfavorable outcomes. Therefore, the course of AP after surgery for endocarditis is of special interest. (2) 314 patients with active isolated left-sided infective endocarditis at the De-partment of Cardiac Surgery (Medical University of Vienna, Austria) between 2009 and 2018 were enrolled in this retrospective analysis. Blood samples were analyzed at different time points (baseline, postoperative day 1-7, postoperative days 14, and 30). Patients were categorized ac-cording to relative alkaline phosphatase drop (≥30% vs. <30%). (3) The rate of postoperative renal replacement therapy with or without prior renal replacement therapy (7.4 vs. 21.8%; p=0.001 and 6.7 vs. 15.6%; p=0.015, respectively) and extracorporeal membrane oxygenation (2.2 vs. 19.0%; p=0.000) was observed after a higher initial alkaline phosphatase drop. Short-term (30-day mor-tality 3.0 vs. 10.6%; p=0.010) and long-term mortality (p=0.008) were significantly impaired after a higher initial alkaline phosphatase drop. (4) The higher initial alkaline phosphatase drop was accompanied by impaired short and long-term outcomes after cardiac surgery for endocarditis. Future risk assessment scores for cardiac surgery should consider alkaline phosphatase.

The local electrical response in alkaline-doped CuInSe₂ films prepared by single step electrodeposition onto Cu substrates was studied by current sensing atomic force microscopy. The CIS films were prepared from single baths containing the dopant ions (Li, Na, K or Cs) and were studied by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy and photocurrent response. Increased crystallinity and surface texturing as the ion size increases was observed as well as enhanced photocurrent response in Cs doped CIS. Li and Na doped films have larger conductivity than the undoped film while the K and Cs doped samples display shorter currents and the current images indicate strong charge accumulation in the K and Cs doped films forming surface capacitors. Corrected CAFM IV curves were adjusted with Shockley equation.

Cassava Solid waste (Onggok) is a solid waste from the cassava-based tapioca industry, the starch content in Onggok is still 50-80 wt.% of residual starch, which can be used to produce maltodextrin for foods application. Furthermore, using cassava solid waste is beneficial in terms of the cost of raw materials. The starch content in cassava can be modified through enzymatic hydrolysis using α-amylase and β-amylase enzymes at 80oC and pH 5.5. Enzymatic hydrolysis was done using mixed enzymes that varied the concentration of α-amylase at 0,.1% and the β-amylase enzymes at 0.05, 0.1, and 0.5%. the concentration of cassava waste (Onggok) varied from 4%, 7%, 10%, and 13%. The optimum concentration of α-amylase and β-amylase enzymes are 0.1% and 0.1% respectively at time intervals of 1 minute resulting in a dextrose equivalent (DE) value 0f 5.7. The characteristics of maltodextrin were studied using scanning electron microscopy (SEM) to determine the morphology of the starch structure which had changed due to the enzyme hydrolysis. Simultaneous thermal analysis (STA) was studied to determine the Thermal stability of hydrolysis products. Maltodextrin produced from cassava waste (Onggok) has a DE value < 10, which has the potential to be used in the pharmaceutical industry

Ready-to-eat fresh fruit have an increasing presence in international markets due to its convenience and health benefits. However, these produces are highly perishable and efficient technologies to increase their shelf life are needed. In the present research, different citrus fruit species and cultivars from organic farming were assayed to obtain enzymatically citrus segments. The best results in terms of segment quality were observed for ‘Hernandina’ clementine which was chosen to make a new ready-to-eat produce based on peeled citrus segments packaged in glass jars with slight syrup made on citrus juice and organic sugar cane. The most appreciated syrup was those containing 50-50 (v/v) of ‘Fino’ lemon juice and ‘Hernandina’ clementine based on the sensory scores given by the panellists. In addition, different pasteurization treatments were assayed to preserve the new produce safety and nutritional and sensory quality properties during storage at cold temperature. Results showed that pasteurization treatment at 50 °C for 45 min could be enough to avoid microbial contamination with mesophilic and psychrophilic aerobic bacteria or yeast and mould and to maintain sensory properties until five weeks of storage at 4 °C. In addition, only a 10 % reduction of vitamin C was observed from fresh segments or syrup until the end of storage period, showing that the new ready-to-eat produce would conserve high bioactive compound content and health benefits after pasteurization and prolonged cold storage.

As abiotic stress, drought limits plant growth and minimizes productivity. The increased request for valuable essential oil extracted from geranium (Pelargonium graveolens L.) is mainly associated with plant growth, which is adversely affected by drought. Melatonin (MT) has been used to enhance plant growth under abiotic stress, however, its impact to overcome drought stress of aromatic plants including geranium is poorly investigated. In the current investigation, MT application at 100 µM was applied under 100 % (well-watered) or 50 % (drought stress) of FC to verify this role. Drought stress markedly reduced growth parameters, herb yield, and total chlorophyll; however, MT alleviated these effects. In contrast, drought enhanced the essential oil percentage in geranium leaves. Despite the reduction in oil yield caused by drought, MT application mitigated this reduction and improved both oil yield and oil components. Besides, MT treatment enhanced the accumulation of total phenols, glutathione, and proline and improved the activity of ascorbate peroxidase, catalase, and glutathione reductase with possible alleviation of drought-induced oxidative damage. Therefore, it reduced both H2O2 and malondialdehyde accumulation, and finally maintained membrane integrity. Overall, this is the first report that reveals that MT application can improve geranium resistance to drought by enhancing the antioxidant potential and protecting the cell membrane from oxidative damage.

Millions of people worldwide are affected by diabetes, a chronic disease that continuously grows due to abnormal glucose concentration levels present in the blood. Monitoring blood glucose concentrations is therefore an essential diabetes indicator to aid in the management of the disease. Enzymatic electrochemical glucose sensors presently account for the bulk of glucose sensors in the market. However, their disadvantages are that they are expensive and are dependent on environmental conditions, hence affecting their performance and sensitivity. To meet the increasing demand, non-enzymatic glucose sensors based on chemically modified electrodes for the direct electrocatalytic oxidation of glucose are a good alternative to the costly enzymatic-based sensors currently on the market, and the research thereof continues to grow. Nanotechnology-based biosensors have been explored for their electronic and mechanical properties, resulting in enhanced biological signalling through the direct oxidation of glucose. Copper oxide and copper sulfide exhibit attractive attributes for sensor application, due to their non-toxic nature, abundance, and their unique properties. Thus, in this review, copper oxide and copper sulfide-based materials, are evaluated based on their chemical structure, morphology, and fast electron mobility as suitable electrode materials for non-enzymatic glucose sensors. The review highlights the present challenges of non-enzymatic glucose sensors that have limited their deployment into the market.

We demonstrate the use of a nanotechnology-based approach for the investigation of enzymatic activity of a single molecule of horseradish peroxidase with a solid-state nanopore. The artificial 5 nm solid-state nanopore has been formed in a 40-nm-thick silicon nitride structure. Single molecule of HRP has been entrapped into the nanopore. The activity of horseradish peroxidase (HRP) enzyme molecule inserted in the nanopore has been monitored by recording the time dependence of the ion current through the nanopore in the course of the reaction of 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonate) (ABTS) oxidation reaction. We have found that in the process of ABTS oxidation in the presence of 2.5 mM hydrogen peroxide, individual HRP enzyme molecules are able to retain activity for approximately 700 seconds before a decrease in the ion current through the nanopore, which can be explained by structural changes of the enzyme.

This work aimed at producing lactic acid (LA) from sugarcane bagasse after steam explosion at 195 ºC for 7.5 and 15 min. Enzymatic hydrolysis was carried out with Novozymes’ Cellic CTec3 and/or Cellic HTec3, whereas fermentation was performed with Bacillus coagulans DSM2314. Water-washing of pretreated solids before enzymatic hydrolysis improved both hydrolysis and fermentation yields. The presence of xylo-oligosaccharides (XOS) in substrate hydrolysates reduced hydrolysis efficiency, but their effect on fermentation was negligible. The presence of fermentation inhibitors in C5 streams was circumvented by adsorption on activated carbon powder with no detectable sugar losses. High carbohydrates-to-LA conversions (Yp/s) of 0.88 g·g-1 were obtained from enzymatic hydrolysates of water-washed steam-exploded materials that were produced at 195°C, 7.5 min and the use of centrifuged-but-never-washed pretreated solids decreased Yp/s by 16%. However, when the detoxified C5 stream was added at a 10% ratio, Yp/s was raised to 0.93 g·g-1 for an LA productivity of 2.55 g·L-1·h-1. Doubling the pretreatment time caused a decrease in Yp/s to 0.78 g·g-1, but LA productivity was the highest (3.20 g·L-1·h-1). For pretreatment at 195°C for 7.5 min, elimination of water washing seemed feasible, but the use of longer pretreatment times made it mandatory to eliminate fermentation inhibitors.

Nanoparticles (NPs) have uniform chemical composition, size, and morphology. Microorganisms are of great interest in Nanoparticle synthesis. The green production of nanomaterials occurs either intracellularly or extracellularly. Gold and silver nanoparticles are mostly synthesised by the enzymatic degradation of metal ions. The produced NPs are characterized by different instruments such as ultraviolet visible, dynamic light scattering, x-ray diffraction, scanning electron microscope, transmission electron microscope, etc. Our review discusses the various biomedical applications of gold and silver nanoparticles synthesized by microbes via intracellular and extracellular mechanisms.

The global development of bioeconomy is impossible without technologies for comprehensive processing of plant renewable resources. The use of proven pretreatment technologies raises the possibility of industrial implementation of enzymatic conversion of polysaccharides from lignocellulose considering the process complexity. For instance, a well-tuned kraft pulping produces a substrate easily degraded by cellulases and hemicelulases. Enzymatic hydrolysis of bleached hardwood kraft pulp was carried out using an enzyme complex of endoglucanases, cellobiohydrolases, b-glucosidases and xylanases produced by recombinant strains of Penicillium verruculosum at a 10 FPU/g mixture rate and a 10 % substrate concentration. As a result of biocatalysis the following products are obtained: sugar solution, mainly glucose, xylobiose, xylose, as well as other minor reducing sugars; modified complex based on cellulose and xylan. The composition of biomodified kraft pulp was determined involving the use of HPLC. The method for determining the degree of crystallinity on an X-ray diffractometer was used to characterize the properties. The article shows the possibility of producing modified cellulose cryogels by amorphization with concentrated 85 % H3PO4 followed by precipitation with water and supercritical drying. Analysis of the enzymatic hydrolysate composition reveals the predominance of glucose (55...67 %) in reducing sugars with a maximum content of up to 6 % in the solution after 72 hours. The properties and structure of modified kraft pulp were shown to change during biocatalysis, in particular, the degree of crystallinity increased by 5 % after 3 hours of enzymatic hydrolysis. We obtained cryogels based on the initial and biomodified kraft pulp with conversion rates of 35, 50 and 70 %. The properties of these cryogels are not inferior to those based on industrial microcrystalline cellulose, as confirmed by the specific surface area, degree of swelling, porosity and SEM images. Thus, kraft pulp enzymatic hydrolysis offers prospects not only for producing sugar-rich hydrolysates for microbiological synthesis, but also for producing cellulose powders and cryogels with specified properties.

Biorefining by enzymatic hydrolysis (EH) of lignocellulosic waste material due to low costs and affordability has received enormous interest amongst scientists as a potential strategy suitable for the production of bioactive ingredients and chemicals. In the present study, a sustainable and eco-friendly approach to the extraction of bound ferulic acid (FA) has been demonstrated using a single-step EH by a mixture of lignocellulose-degrading enzymes. For comparative purposes of the efficiency of EH, an online SFE-SFC-MS extraction and analysis approach was applied. The experimental results demonstrated up to 369.3 mg 100 g−1 FA released from rye bran after 48 h EH with Viscozyme L. The EH of wheat and oat bran with Viscoferm for 48 h resulted in 255.1 and 33.5 mg 100 g−1 of FA, respectively. The extraction of FA from bran matrix using the SFE-CO2-EtOH delivered up to 464.3 mg 100 g−1 of FA, though the extractability varied depending on the parameters used. The 10-fold and 30-fold scale-up experiments confirmed the applicability of EH as a bioprocessing method valid for industrial-scale. The highest yield of FA in both scale-up experiments was obtained from rye bran after 48 h of EH with Viscozyme L. In purified extracts, the absence of xylose, arabinose, and glucose as final degradation products of lignocellulose was proven by a HPLC-RID system. Up to 94.0% purity of FA was achieved by SPE using the polymeric reversed-phase Strata X column and 50% EtOH as eluent.

The use of low-intensity ultrasound has gotten surprising consideration over the last decade as a method for enhancing the catalytic activity of the enzyme. Ultrasounds have the potential to significantly influence the activity of the enzymatic processes, provided that the energy input is not too high to inactivate the enzyme. By providing the variation in parameters, various physical and chemical effects can be attained that can enhance the enzymatic reaction. Ultrasonic reactors are known for their application in bioprocesses. However, the potential of their applications is still limited broadly due to the lack of proper information about their operational and performance parameters. In this review, the detailed information about ultrasonic reactors is provided by defining the different types of reactors, number and position of ultrasonic transducers. Also, it includes the mechanism of intensification and influence of ultrasonic parameters (intensity, duty cycle and frequency) and enzymatic factors (enzyme concentration, temperature and pH) on the catalytic activity of enzyme during ultrasound treatment.

The microorganisms able of accumulating lipids in high percentages, known as oleaginous microorganisms, have been widely studied as an alternative for producing oleochemicals and biofuels. Microbial lipid, so called Single Cell Oil (SCO), production depends on several growth parameters, including the nature of the carbon substrate, which must be efficiently taken up and converted into storage lipid. Οn the other hand, substrates considered for large scale applications must be abundant and of low acquisition cost. Among others, lignocellulosic biomass is a promising renewable substrate containing high percentages of assimilable sugars (hexoses and pentoses). However, it is also highly recalcitrant and therefore it requires specific pretreatments in order to release its assimilable components. The main drawback of lignocellulose pretreatment is the generation of several by-products that can inhibit the microbial metabolism. In this review, we discuss the main aspects related to the cultivation of oleaginous microorganisms using lignocellulosic biomass as substrate, hoping to contribute to the development of a sustainable process for SCO production in the near future.

Ionic liquids have been recognised as interesting solvents applicable in the efficient lignocellulosic biomass valorisation, especially in the biomass fractionation into individual polymeric components or direct hydrolysis some of biomass fractions. Considering the chemical character of ionic liquids, two different approaches, paved the way for a fractionation of biomass. The first strategy integrated a pre-treatment, hydrolysis and conversion of biomass through the employment of hydrogen-bond acidic 1-ethyl-3-methyimidazolim hydrogen sulfate ionic liquid. The second one relied on the use of a three-step fractionation process with hydrogen-bond basic 1-ethyl-3-methylimidazolium acetate to produce high purity cellulose, hemicellulose and lignin fractions. The proposed approaches were scrutinised for wheat straw and eucalyptus residues. Those different biomasses allowed understanding that enzymatic hydrolysis yields are dependent on the crystallinity of pre-treated biomass. The use of acetate based ionic liquid allowed to change crystalline cellulose I to cellulose II and consequently enhanced glucan to glucose yield to 93.14.1 mol% and 82.91.2 mol% for wheat straw and eucalyptus, respectively. Whereas for hydrogen sulfate ionic liquid, the same enzymatic hydrolysis yields were 61.6  0.2 mol% for wheat straw and only 7.90.3 mol% for eucalyptus residues. These results demonstrate the importance of either ionic liquid character or biomass type on the efficient biomass processing.

Enzymatic degradation of organic pollutants is a new and promising remediation approach. Peroxidases are one of the most commonly used classes of enzymes to degrade organic pollutants. However, it is generally assumed that all peroxidases behave similarly and produce similar degradation products. In this study, we conducted detailed studies of the degradation of a model aromatic pollutant, Sulforhodamine B dye (SRB dye), using two peroxidases—soybean peroxidase (SBP) and chloroperoxidase (CPO). Our results show that these two related enzymes had different optimum conditions (pH, temperature, H₂O₂ concentration...etc.) for efficiently degrading SRB dye. High-performance liquid chromatography and LC-mass spectrometry analyses confirmed that both SBP and CPO transformed the SRB dye into low molecular weight intermediates. While most of the intermediates produced by the two enzymes were the same, the CPO treatment produced at least one different intermediate. Furthermore, toxicological evaluation using lettuce (Lactuca sativa) seeds demonstrated that the SBP-based treatment was able to eliminate the phytotoxicity of SRB dye, but the CPO-based treatment did not. Our results show, for the first time, that while both of these related enzymes can be used to efficiently degrade organic pollutants, they have different optimum reaction conditions and may not be equally efficient in detoxification of organic pollutants.

Electronic waste (e-waste), characterized by the widespread disposal of electronic devices, shows a growing environmental challenge. In this study, we explore the electrocatalytic potential of gold nanoparticles supported on Vulcan obtained from e-waste for their application as electrocatalysts for the methanol oxidation reaction in alkaline media. Gold nanoparticles are synthesized from gold coatings recovered from Intel Pentium 4 processor pins, highlighting their sustainability as electrocatalyst precursors. Comprehensive characterization, including UV-Vis spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray dif-fraction, is performed to assess the electrocatalyst's structural properties. Electrochemical evalu-ation is carried out in 0.5 M KOH electrolyte employing the rotating disk electrode technique, us-ing cyclic voltammetry for the study of methanol oxidation. Remarkably, the gold nanoparticles show electrocatalytic activity on par with commercially synthesized counterparts, demonstrating the feasibility of this approach for sustainable electrocatalyst production. Thus, this research opens new routes for utilizing e-waste as a source of valuable catalyst materials, addressing en-vironmental and technological challenges in the field of alkaline fuel cells.

Medicinal plants for bone grafts are promising because they are free from infecting microorganisms and biocompatible. We report a novel study evaluating osteoregeneration of bone grafts from extracts of Alternanthera brasiliana and Fridericia platyphylla after bone injury induced by radius fracture in rats. Grafts were obtained using 2% chitosan gel and 0.5% hydroalcoholic extract. The rats were randomly divided into four experimental groups (N= 12): Negative control (NC) - Chitosan gel; Positive control (PC) - bovine mineral bone graft (Lumina Bone®, fine powder 0.5); F. platyphylla Graft (FRID) - 0.5% bone graft; A. brasiliana Graft (ABRA) - 0.5% bone graft. The animals were evaluated for three periods, 30, 60, and 90 days after fracture induction. Bone alkaline phosphatase (BSAP) and radiographic and histological evaluations were followed. After 90 days, there was an increase in BSAP for the ABRA group on the newly formed bone matrix but not for FRID, indicating the presence of active osteoblasts. Additionally, mature bone tissue and bone remodeling were observed, and a conspicuous presence of type I collagen for both FRID and ABRA. We demonstrated that FRID and ABRA grafts produced early bone neoformation. New perspectives for these species as a graft are suggested.

To investigate this suitability of Black Mustard (Brassica Nigra L.) and Camelina (Camelina Sativa L.) for pulp manufacturing the nitrate-alkaline method was used. The non-wood plants were characterized by chemical analysis, especially lignin, cellulose, ash, extractives and alpha-, beta-, gamma-cellulose. The pulp was cooked in 6% nitric acid and then underwent the extraction by 5% sodium-hydroxide and neutralized by 1% acetic acid. The cooked pulp was characterized by delignification degree – Kappa number. The laboratory sheets were made from this cooked pulp and they were characterized by tensile index, breaking length, smoothness and compared with commonly available papers.

Selection of efficient corrosion inhibitors requires detailed knowledge regarding interaction mechanism, which depends on the type and amount of functional groups within the inhibitor molecule. Position of functional groups between different isomers is often overlooked but not less important since factors like steric hinderance may significantly affect the adsorption mechanism. In this study we have presented how different dihydroxybenzene isomers interact with aluminium alloy 5754 surface, reducing its corrosion rate in bicarbonate buffer (pH = 11). We have shown the highest inhibition efficiency among tested compounds belongs to catechol at 10 mM concentration, although differences were moderate. Utilization of novel impedance approach to adsorption isotherm determination allowed to confirm that while resorcinol chemisorbs on aluminium surface, catechol and quinol follows ligand exchange model of adsorption. Unlike catechol and quinol, the protection mechanism of resorcinol is bound to interaction with insoluble aluminium corrosion products layer and was only found efficient at concentration of 100 mM (98.7%). The aforementioned studies were confirmed with scanning electron microscopy and x-ray photoelectron spectroscopy analyses. There is a significant increase of the corrosion resistance offered by catechol at 10 mM after 24 h exposure in electrolyte: from 63 to 98%, with only negligible changes in inhibitor efficiency observed for resorcinol at the same time. However, in the case of resorcinol a change in electrolyte color was observed. We have revealed that the differentiating factor is the keto-enol tautomerism. The NMR studies of resorcinol indicate the keto form in structure in presence of NaOH, while the chemical structure of catechol does not change significantly in alkaline environment.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Membrane processes, such as microfiltration, ultrafiltration, and nanofiltration are increasingly used for various applications in both upstream and downstream processing. Membrane-based processes play a critical role in the field of separation/purification of biotechnological products, including protein production/purification. The possibility of using membranes to separate peptides from a chicken byproduct hydrolysate and the effect of the performed downstream processing on the DPP-IV inhibitory activity of MDCR (mechanical deboning chicken residue) has been investigated. The chicken byproduct hydrolysate was prepared by enzymatic hydrolysis followed by MF, UF, NF, and RO separation. The LC-OCD analysis confirmed that NF and RO would retain the bioactive peptides in the concentrate in comparison to MF and UF. Bioactivity was correlated with molecular weight distribution profiles and average molecular weights. Permeates after ultrafiltration showed an IC50 value of 0.75 mg/mL, comparable to other potent DPP-IV inhibitors derived from various food sources, and significantly more potent compared to the microfiltration sample, which showed an IC50 value of 1.04 mg/mL. The average molecular weight of the permeates calculated from the SEC chromatograms was 883 g/mol for UF and 1437 g/mol for MF. Of the four membranes studied, the UF membrane showed the best separation properties with respect to maximizing the yield and up-concentration of the bioactive peptides. Overall, UF was demonstrated to be a feasible technology for the removal of the undesired high molecular weight substances and up-concentration of small molecular weight bioactive peptides from chicken byproduct hydrolysate.

Introduction: Mucopolysaccharidosis type I (MPSI) is an autosomal recessive lysosomal storage disorder characterized by deficient or absent α-L-iduronidase (IDUA) enzyme activity due to pathogenic variants in IDUA gene. Early treatment with hematopoietic stem cell transplantation and/or enzyme replacement therapy is associated with improved outcomes in this progressive multisystem disease. The diagnosis is usually delayed due to late presentation and nonspecific symptoms resulting in high morbidity and mortality. The incidence of MPSI in US is estimated to be 0.26:100,000, however, it is unknown in Kuwait. This pilot study was undertaken to screen MPSI in all Kuwaiti neonates born at Farwaniya Hospital over a period of 12-months. This study examined the incidence of MPSI in a major center in Kuwait for inclusion in the national newborn screening program to enable its early detection and adequate treatment. Methods: All Kuwaiti neonates born at Farwaniya Hospital, Kuwait from December 2021 to December 2022, were screened for MPSI. The screening consisted of determining IDUA enzyme activity in dried blood spots (DBS)-derived samples by Tandem Mass Spectrometry. A follow-up genetic analysis of IDUA gene is planned to screen the cases with diminished IDUA enzyme activity as second-tier testing. Results: A total of 618 newborns, including 331 (54%) males and 287 (46%) females, were screened. Twenty of them had deficient IDUA enzyme activity but showed negative genetic testing for IDUA. However, we have diagnosed one additional female baby with MPSI, who belonged to Farwaniya Hospital, but the parents chose to deliver in a private hospital. She presented at age three months with recurrent upper airway infections, snoring and extensive Mongolian spots. The molecular study revealed previously reported pathogenic nonsense variant in IDUA c.1882C>T; p.(Arg628Ter), associated with severe phenotype. That being included, MPSI is estimated to be about 0.3% among tested females and 0.2% of all screened cases in Kuwait. Conclusion: Our study is the first to evaluate the incidence of MPSI in Kuwait. Given the single center, small number of screened babies and the short study duration thus far, it is premature to calculate the incidence of MPSI. It is anticipated that as the study continues and more infants are examined, we would be able to estimate the incidence of this disease in our population correctly. Further studies including screening newborns in all maternity hospitals in Kuwait are needed to calculate the actual incidence of MPSI. Our data supports including MPSI in national newborn screening program to allow early initiation of treatment and thus improve disease outcome.

Beef potentiator is an important flavor enhancer in food industry, while it is prone to generating insufficient taste compounds and off-odor compounds during enzymatic hydrolysis of beef, resulting in poor flavor of beef potentiator. It has been extensively reported that sonication is capable of improving food flavor. However, the effect of sonication on the flavor of enzymatically hydrolyzed beef liquid (EHBL) was scarcely reported. Herein, we investigated the effect of sonication on the flavor of EHBL using quantitative descriptive analysis (QDA), physicochemical analysis and SPME-GC-olfactometry/MS. QDA showed that sonication had a significant effect on taste improvement and off-odor removal of EHBL. Compared with the control, sonication (40 kHz, 80 W/L) increased the contents of total nitrogen, formaldehyde nitrogen, total sugar, reducing sugar, free amino acids (FAAs) and hydrolysis degree of EHBL by 19.25%, 19.80%, 11.83%, 9.52%, 14.37% and 20.45%. Notably, sonication markedly enhanced the contents of sweet FAAs, umami FAAs and bitter FAAs of EHBL by 19.66%, 14.04% and 9.18%, respectively, which contributed to the taste improvement of EHBL. SPME-GC-olfactometry/MS analysis showed that aldehydes and alcohols were the main contributors to aroma compounds of EHBL, sonication significantly increased the contents of key aroma compounds and 115.88% of alcohols content in EHBL. Notably, sonication decreased contents of the fishy odorants, hexanoic acid and nonanal, markedly by 35.29% and 26.03%, which was responsible for the aroma improvement of EHBL. Therefore, sonication could become a new potential tool to improve the flavor of EHBL.

Antisense oligonucleotides (ASONs) have proven potential for the treatment of various diseases. However, their limited bioavailability restricts their clinical application. New structures with improved enzyme resistance stability and efficient drug delivery are needed. In this work, we propose a novel category of ASONs bearing anisamide conjugation at phosphorothioate sites for oncotherapy. ASONs can be conjugated with the ligand anisamide very efficiently and flexibly in solution. The conjugation sites and ligand amount both influence anti-enzymatic stability and cellular uptake, resulting in changes in antitumor activity that are detectable by cytotoxicity assay. T6 (with double end AA-conjugation) was identified as the optimal conjugate, and its antitumor activity and the underlying mechanism were examined further in vitro and in vivo. This paper presents a new strategy for the design of nucleic acid–based therapeutics with improved drug delivery and biophysical and biological efficacy.

The integration of metal nanoparticles and solid carriers can achieve ideal stability, high load and good conductivity. In this work, copper nanoparticles (Cu NPs) were sequentially deposited on a cobalt metal-organic framework (Co-MOF) by bonding with exposed imino groups, followed by a reduction reaction to prepare a new Cu@Co-MOF composite. Cu@Co-MOF acts as a non-enzymatic electrochemical sensor to detect glucose (Glu) in an alkaline medium. The composite working electrode of Cu@Co-MOF/GCE (GCE = glassy carbon electrode) improves the electrocatalytic activity for Glu oxidation. Cu@Co-MOF/GCE shows excellent electrocatalytic performances in Glu concentration ranging 0.005~1.8 mmol∙L⁻¹ (mM): the sensitivities are 282.89 μA∙mM⁻¹∙cm⁻² in 0.005-0.4 mM Glu and 113.15 μA∙mM⁻¹∙cm⁻² in 0.4-1.8 mM Glu respectively with low detection limit of 1.6 μM (S/N = 3) and high selectivity and stability.

Selenium (Se) is an essential element of the human diet. Therefore, it is necessary to implement Se in agricultural fertilization, although it is not considered as an essential element for plants, Se provides benefits at the level of redox metabolism, increasing the resistance of plants to various stress factors. The increase of the availability of selenium with the use of biopolymer complexes was sought in Great Lakes lettuce grown in substrate pots treated with SeO₂ (5 mg L Se), Cs-PAA + Se (5 mg L Se), and Cs-PAA. The redox metabolism was modified by increasing the enzymatic activity of glutathione peroxidase. The use of Cs-PAA + Se biopolymer complexes increase selenium up to 24 mg/Kg dry weight (DW) in plant tissues.

The Fengcheng Formation in the Mahu Sag of the Junggar Basin was generally composed of detritus, pyroclastic material, carbonates, and evaporites. During the process of sedimentation, the climate was arid or semi-arid. Due to the effect of high concentration and sodium-rich source, an alkaline lake was formed, and alkaline minerals were also preserved in the stratum. After the sediments were buried, three mineral assemblages were formed in the Fengcheng Formation, which are carbonate mineral assemblages (i.e., calcite + ferreous dolomite), reedmergnerite and carbonate mineral assemblages (i.e., reedmergnerite + calcite + ferreous dolomite), and reedmergnerite and alkaline mineral assemblages (i.e., reedmergnerite + shortite + trona), respectively. According to the homogenization temperature of reedmergnerite primary fluid inclusions, alkaline diagenesis of Fengcheng Formation is divided into early stage（≤100℃） and middle stage（＞100℃）, respectively. The former is characterized by the generation of ferreous saddle dolomite, quartz dissolution, and agglutination of the laumontite, which occurred under normal burial conditions. The latter is marked by the reedmergnerite’s appearance, which is correlated to deep hydrothermal activity controlled by faults. Finally, based on sedimentary and diagenetic factors, including climate, provenance, diagenetic surroundings, and the action of subsurface fluid, the alkaline deposition-diagenesis model for shale series in four stages of the Fengcheng Formation was established.

Reactive oxygen species (ROS) are a major risk factor for the development of oxidation and inflammation. Ryegrass (pasture), a natural dietary fiber source, acts as an antioxidant with well-known anti-inflammatory properties. The current study aimed to examine the alkaline phosphatase (ALP)-dependent Kelch-like-ECH-associated protein 1- Nuclear factor erythroid 2-related factor 2 (Keap1-Nrf2) signaling pathway that facilitates the anti-oxidative and anti-inflammatory properties of pasture and its protective effects on ileal permeability, systemic inflammation, nutrient absorption, liver dysfunction, growth performance, intestinal organ development, and metabolic syndrome in commercial diet-challenged geese. The lipopolysaccharides (LPS), ALP, ROS, and tight junction proteins were determined from the ileum tissues, and the antioxidant enzymes, immunoglobulins, and metabolic syndrome were determined from liver tissues via Enzyme-linked immunosorbent assay (ELISA) kits. While the Nrf2 and LPS/ROS/Keap1-induced inflammatory cytokines were determined by the quantitative reverse transcription polymerase chain reaction (RT-qPCR) method. The intestinal morphology was examined by Hematoxylin and Eosin (H&E) staining to determine nutrient absorption in ileal tissues. Pasture-dependent ALP activity significantly ameliorated commercial diet-induced LPS and ROS-facilitated ileal barrier dysfunction and systemic inflammation. The pasture supplementation induced nutrient absorption by influencing intestinal organ development. Our biochemical assays showed that the activation of Nrf2 significantly increased antioxidant enzymes and immunoglobulins, and decreased Keap1 and malondialdehyde (MDA) concentrations in the liver tissues after pasture supplementation. The correlation analysis of ALP, LPS, ROS, and Keap1-Nrf2 pathway-dependent antioxidant enzymes with other host markers showed that pasture supplementation induced intestinal barrier function via reducing LPS/ROS-induced intestinal permeability and systemic inflammation in the ileum and liver tissues. Pasture intake might attenuate LPS/ROS-induced gut permeability, systemic inflammation, and metabolic syndrome and augment gut barrier functions, nutrient absorption, immunity, and growth performance, possibly by its Keap1-Nrf2 pathway-dependent antioxidant properties.

The work reports a facile synthesis of high thermally-stable nanocrystalline anatase TiO2 nanoparticles (NPs) doped with different atomic concentrations (0.5, 1.0, 3.0, and 6.0%) of Gd3+ and Nd3+ ions by a template-free and one-step solvothermal process, using titanium(IV) butoxide as titanium precursor and dimethyl sulfoxide (DMSO) as solvent. The structure and morphology of the Gd3+, Nd3+, and 0.5%Gd3+-0.5%Nd3+/doped TiO2 NPs have been characterized by using various analytical techniques. The Gd3+/ and Nd3+/TiO2 molar ratios were found to have a pronounced impact on the crystalline structure, size, and morphology of TiO2 NPs. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) studies revealed the proper substitution of Ti4+ by Gd3+ and Nd3+ ions in the TiO2 host lattice. The as-prepared Gdx/TiO2, Ndx/TiO2, and Gd1.0/Ndx/TiO2 bimetallic NPs, x = 0.5, 1.0, 3.0, and 6%, have been investigated as electrocatalysts for hydrogen evolution reaction (HER) in 1.0 M KOH solution using a variety of electrochemical techniques. At any doping percentage, the Gd1.0/Ndx/TiO2 bimetallic NPs showed higher HER catalytic performance than their corresponding counterparts i.e. Gdx/TiO2 and Ndx/TiO2. Upon increasing the Nd content from 0.5 to 6.0%, the HER catalytic performance of the Gd1.0/Ndx/TiO2 bimetallic NPs was generally enhanced. Among the studied materials, the bimetallic Gd1.0/Nd6.0/TiO2 NPs emerged as the most promising catalyst with an onset potential of -22 mV vs. RHE, a Tafel slope of 109 mV dec-1, and an exchange current density of 0.72 mA cm-2. Such HER electrochemical kinetic parameters are close to those recorded by the commercial Pt/C (onset potential: -15 mV, Tafel slope: 106 mV dec-1, and exchange current density: 0.80 mA cm-2), and also comparable with those measured by the most active electrocatalysts reported in the literature. The synergistic interaction of Gd and Nd is thought to be the major cause of the bimetallic catalyst's activity.

As the global energy crisis continues, efficient hydrogen production is one of the hottest topics these days. In this sense, establishing catalytic trends for hydrogen production is essential for choosing proper H2 generation technology and catalytic material. Volcano plots for hydrogen evolution in acidic media are well-known, while volcano plot in alkaline media was constructed ten years ago using theoretically calculated hydrogen binding energies. Here we show for the first time that the volcano-type relationships are largely maintained in a wide range of pH values, from acidic to neutral and alkaline solutions, using theoretically calculated hydrogen binding energies on clean metallic surfaces and experimentally measured hydrogen evolution overpotentials. If metallic surfaces are exposed to high anodic potentials, hydrogen evolution can be boosted or significantly impeded, depending on the metal and the electrolyte in which the reaction occurs. Such effects are discussed here and can be used to properly tailor catalytic materials for hydrogen production via different water electrolysis technologies.

Ca-bentonite (CB) alone and in a mixture with limestone (L), tobacco biochar (TB) and zeolite (Z) on the fixation, geochemical fractions and absorption of Cd and Zn by Chinese cabbage in smelter heavily polluted (S-HP) and smelter low polluted (S-LP) soils were investigated. The results showed that the CB+TB and CB+L+TB treatments significantly immobilized Cd up to 22.03% and 29.68%, respectively, and reduced uptake by Chinese cabbage shoot to 35.98% with CB+Z+L and 61.35% with CB+L in S-HP and S-LP soils compared with the control. The CB+ Z+ L+TB treatment mobilized Cd up to 4.45% and increased absorption in the shoot by 9.85% in S-HP soil. The greatest immobilization of Zn was 53.18% and 58.20% with the CB+Z+L+TB treatment, which reduced Zn uptake in the plant shoot by 9.94% with CB + L and 58.04 with CB+Z+L+TB in S-HP and S-LP soils. The CB+Z+TB and CB+TB treatments mobilized Zn up to 35.40% and 4.80%, respectively, in both soils. Furthermore, the uptake of Zn in plant shoot was observed by 58.96% and 7.82% with application of CB+Z and CB+TB treatments, respectively, in S-HP and S-LP soils. Overall, our results suggest that Ca-bentonite alone and in mixtures with different amendments can be used to reduce the phyto-extraction of Cd and Zn in Zn-smelter polluted soils.

For efficient electrode development in an electrolysis system, Fe₂O₃, MnO, and heterojunction Fe₂O₃-MnO materials were synthesized via a simple sol-gel method. These particles were coated on a Ni-foam electrode, and the resulting material was used as an electrode to be used during an oxygen evolution reaction (OER). A 1000-cycle OER test in a KOH alkaline electrolyte indicated that the heterojunction Fe₂O₃-MnO/NF electrode exhibited the most stable and highest OER activity: it exhibited a low overvoltage (n) of 370 mV and a small Tafel slope of 66 mV/dec. X-ray photoelectron spectroscopy indicated that the excellent redox performance contributed to the synergy of Mn and Fe, which enhanced the OER performance of the Fe₂O₃-MnO/NF electrode. Furthermore, the effective redox reaction of Mn and Fe indicated that the structure maintained stability even under 1000 repeated OER cycles.

Copper mine tailings are the residual products after the purification of precious copper from copper ores, and their storage can create numerous environmental problems. Many researchers have used copper mine tailings for preparation of geopolymer. This paper studies the enhancement of the cementitious activity of copper mine tailings in geopolymer system. First, copper mine tailings are activated through a mechanical grinding activation. Afterward, the mechanically activated copper mine tailings are further processed through thermal activation and alkaline roasting activating. The cementitious activity index of copper mine tailings is characterized through the degree of concentration of alkali leaching silicon and aluminum. It was observed that the Si and Al alkali leaching concentration of mechanical activated tailings was increased by 26.03% and 93.33%, respectively. The concentration of Si and Al was increased by 54.19% and 119.92%, respectively. For alkaline roasting activating, roasting time, temperature and (C/N ratio) were evaluated through the orthogonal test, and the best condition was activation for 120 min at 600℃ with C/N ratio is 5:1. In this study, the SEM, XRD and IR analysis show that mechanically activation, thermal activation and alkaline roasting activating can improve the cementitious activity index of copper mine tailings.

Background Cytomegalovirus (CMV) is a major pathogen that cause remarkable rate of morbidity and mortality, especially in immunocompromised patients. It is important to find risk factors associated with CMV viremia. We studied the differences in CMV seropositivity in relation to liver function biomarkers in male and female Saudi population in an attempt to understand the variation in the CMV seroprevalence with sex and find the risk factor to develop liver dysfunction or hepatocellular carcinoma. Material and subjects: The CMV- IgG and IgM were screened in serum samples of 150 non- A-G hepatities patients with elevation of liver profiles (ALT, AST, ALP and GGT) and categorized as males and females. Samples were collected from different general hospitals and polyclinic in KSA from March 2014 to June 2015. A correlation between CMV seropositivity measured with both antibodies and liver enzymes were tested. Receiver operating characteristics (ROC) analysis and multiple regressions were done for the obtained data. Results: Our study shows that females had much higher IgG and IgM compared to age-matching males. A significant correlation between both antibodies and liver enzymes (AST, ALT) was recorded. Less significant correlation of both IgG and IgM with GGT was also observed. Receiver operating characteristics (ROC) analysis revealed that both IgG and IgM can be used as excellent predictive markers for CMV infection as both recorded 100% specificity and sensitivity together with area under the curve of 1 in males and females. Multiple regression analysis ascertain the correlation between both antibodies as dependent variables and liver enzymes as independent variables with ALT being the most affected enzyme with CMV seropositivity especially in females. Conclusion:he data discussed above This study shows that CMV is capable of initiating and accelerating liver dysfunction in both sexes. The high seroprevalence in females at reproductive age is especially important as they can transmit the virus to their developing fetus. Prevention of CMV infection in young girls 11-14 years old, through counseling on hygiene or possible future vaccination, may lead to a decrease of congenital CMV infections with the concomitant risk of developing liver dysfunction or hepatocellular carcinoma. Keywords: Cytomegalovirus, Alanine transaminase, Aspartate transaminase Alkaline phosphatase, γ-Glutamyltranspeptidase, liver function.

Gelatin fibers have a specific surface and high porosity, which is why their use in medicine and the food industry is being researched. This article explores the potential of centrifugal spinning to produce gelatin fibers. Gelatin for fiber preparation is obtained from a non-traditional source of collagen (chicken by-products) using a unique enzymatic process. The fiber quality is compared with those prepared from traditional collagen tissues (porcine, bovine). The results show that fibers crosslinked with glutaraldehyde vapor preserve their structure even in contact with water. Using a cross-linker controls swelling ability and solubility while maintaining the fiber structure. On the contrary, uncross-linked gelatin fibers are water soluble due to a high surface-to-volume ratio, facilitating water penetration and dissolution. Scanning electron microscopy (SEM) provided a clearer picture of the morphology of gelatin fibers obtained by centrifugal spinning. Differences in the amount of bonding depending on the raw material used and the presence of cross-linker were analyzed using Fourier transform infrared spectroscopy (FTIR). The overall results showed that chicken gelatin is a suitable alternative to gelatins from traditional sources.

Pesticides are chemical products are used to protect crops to prevent or eliminate undesirable organisms. Pesticides can contaminate continental waters, air, soil and food products. The presence of pesticide residues must therefore be monitored in water and food using sensitive, reliable and broad-spectrum analytical methods, as there is a huge variety of pesticides. Biosensors are one of the screening methods with great potential for detecting residues below the maximum residue limits. The different sensing principles of enzymatic biosensors for pesticide analysis will be described. This review highlights the great potential of colorimetric, enzymatic biosensors for detecting pesticide residues in water and food. Moreover the development of dual colorimetric and fluorimetric sensors during the past years is presented. These methods are most often based on the enzyme acetylcholinesterase, whose activity is inhibited by pesticides. The different approaches used in the development of these biosensors will be detailed, based on different chemical substrates, fluorophores and nanomaterials. The advantages and disadvantages of each approach will be discussed. Finally, the development prospects for improving these biosensors will be presented.

The aim of this study was to investigate the potential of converting potato peel waste into bio ethanol using an in-house produced multi-enzyme preparation. To achieve this, a variety of pre-treatment strategies, including thermal, chemical, and thermo-chemical methods, were applied to the potato peels. These included boiling for 30 and 60 min, steam at varying pressures and times, and different concentrations of chemicals such as H2SO4, HNO3, CH3COOH, HCl, NaOH, Ca(OH)2, KOH, NH3, and H2O2, either alone or in combination with steam. The pre-treated potato peels were then enzymatically hydrolyzed using a crude multi-enzyme cocktail derived from solid-state fermentation of wheat bran by a natural variety of Aspergillus niger P-19, containing cellulases, hemicellulases, pectinase, and amylases. The most effective pre-treatment combination was found to be 3% H2SO4 followed by steam under pressure and enzymatic hydrolysis using the crude multi-enzyme preparation. This combination resulted in the highest yield of reducing sugars (141.04 ±12.31 g/l) with a 98.49% carbohydrate conversion at a 20% substrate loading, giving an ethanol yield of 43.2 g/l. Furthermore, supplementing the medium with peptone, (NH4)(H2PO4), and ZnSO4 at 0.1%w/v each with 22% and 24% solid, respectively, resulted in appreciable yields of 51.67 and 54.75 g/l, further enhancing the ethanol yield.

This lack of information is due to the primary role of HSTs in fungal pathogenesis, which often masks the functions of NSTs and CWDEs. So, the toxic effects of A. alternata metabolites due to NSTs and CWDEs have received minor attention than those reported for HSTs mycotoxins [11]. A wider study of the activity of isolated fungal metabolites can allow the identification of compounds directly related to the pathogenic activity of the fungus, making it possible to create chemo libraries that facilitate the linking of the structure of the compounds with the species that produce it and its effect on host and non-host crops, as well as with biosynthetic features [12]. In this context, our work reports a study focused on NSTs and CWDEs used by an A. alternata strain isolated from infected pears in Italy. To this aim, the characterization of hydrolytic enzyme activities of A. alternata and the identification of the metabolites produced in vitro were performed. Furthermore, the phytotoxic activity of the isolated compounds was evaluated on pear (host and non-host varieties) and lemon fruits [13]. Finally, the competition of A. alternata with other pathogens was evaluated to investigate the role of NSTs on co-infections.

Polydopamine (PDA) deposition, obtained from the oxidation of dopamine and other catecholamines is an universal way to coat all known materials with a conformal coating which can subsequently be functionalyzed at will. The structural analogies between polydopamine and eumelanin, the black-brown pigment of the skin, incited to produce stable polydopamine nanoparticles in solution instead of amorphous precipitates obtained from the oxidation of dopamine. Herein, we demonstrate that size controlled and colloidally stable PDA based nanoparticles can be obtained in acidic conditions, where spontaneous auto-oxidation of dopamine is suppressed, using sodium periodate as the oxidant and a protein like alkaline phosphatase as a templating agent. The size of the PDA@Alp nanoparticles depends on the dopamine/enzyme ratio and the obtained particles display the enzymatic activity of alkaline phosphatase with an activity extending up to two weeks after particle synthesis. The PDA@ alkaline phosphatase (Alp) nanoparticles can be engineered in polyelectrolyte multilayered films to potentially design model biosensors.

A notable REE mineralization in Europe is associated with the Ditrău Alkaline Massif (DAM) in the Eastern Carpathians (Romania). It is an expression of the latest hydrothermal phase in the DAM and is found in the form of mineralized carbonate veins cross-cutting the complex in the NW (Jolotca region) and the SE (Belcina region) parts of the DAM. In the Belcina veins monazite-(Ce), xenotime-(Y), apatite, together with Fe-Mg-rich carbonate, thorite, thorogummite, gedrite and plagioclase are rock-forming. Three different textural and chemical types of the monazite-(Ce) and the xenotime-(Y) document a three-stage evolution. The relative phosphate age succession (from older to younger) thereby is xnt1 > xnt2 (>)+ mnz1 + Fe2O3 + Fe-gedrite > mnz2 + Fe-dolomite (+ plagioclase) > mnz3 + xnt3 + apatite. Phosphate chemistry shows that these crystallized from hydrothermal fluids, whereby each phosphate type follows a separate evolutionary path recommending growth from (at least) 3 independent and successive hydrothermal fluids. Chemistry and pathways within the DAM suggest that these hydrothermal fluids could be derived from a subsurface carbonatitic intrusion. Mnz1,2 and xnt1,2 ages are tightly cluster at 215.8 ± 0.7 Ma (Norian, Upper Triassic). The third-generation phosphate ages are younger, but associated with large analytical uncertainties and did not deliver geologically useful ages. The mean age of ca. 216 Ma is interpreted as timing the Belcina REE mineralization, what together with the fluid chemistry, supports a model of the presence of a late-stage, independent carbonatitic intrusion about 10 Ma after the main igneous activity (ca. 235 - 225 Ma) forming the DAM, synchronous with extension-related magmatism in the region.

PH value is one of the most significant ecological factors affecting the survival and growth of aquatic organisms. But the effect and tolerance of pH value on many aquatic species are still unknown. This study mainly investigated the effects of pH value on the hatching rate of eggs, the adaptability of newly hatched larva fish and the survival of 3-months-old juvenile fish of Takifugu obscurus. Water pH values can cause a great impact on Takifugu obscurus lives, when the fertilized eggs of Takifugu obscurus were incubated at pH 5.0, 6.0, 7.0, 8.0, 8.3 (control group), 9.0, 10.0 and 11.0 respectively. Under the pH of 5.0, 6.0, 10.0 and 11.0, the hatching rate and speed is greatly reduced and the deformity rate of hatching larvae is greatly increased; When the hatch-pH value was 6.0, the acid adaption of hatched larvae was significantly enhanced, but alkali adaptation was weakened; Under the condition of pH gradient of 6.0, 6.4, 6.8, 7.0, 8.0, 8.3, 9.0, 10.0, 10.2, 10.5, 11.0 and 12.0, survival time and survival rate of juvenile fish show a significant difference. Especially when the pH value was 6.0 and 12.0, juvenile fish die immediately after swimming quickly. Within 24 h, half of the fish died at the pH of 6.4 and 10.3, and within 48 h, half died at the pH of 7.1 and 9.9. In addition, the gradual pH value group in which the pH value gradually decreased or increased had stronger acid-base adaptability and a higher survival rate than the acute experimental group. The above results show the relationship between pH value and survival of Takifugu obscurus, which can provide more reference for the introduction of Takifugu obscurus into saline-alkali land in the future. Additionally, the incubated pH value can influence the pH tolerance of Takifugu obscurus, which can be applied to the breed improvement into an appropriate water environment.

Nickel foam substrates are frequently utilised for renewable energy applications as porous 3D-substrates. Preparation of these substrates usually includes an acid washing step, however the degree to which this step affects the final electrochemical performance after spray coating a catalyst ink is unreported. Herein, we report the effect of acid washing through physicochemical and electrochemical characterisation. The electrochemical performance was determined by repeated measurements of catalyst-coated nickel foam substrates both with and without the initial step of acid washing. Acid washing increased current density by 17.9% for the acid treated, MoS2-coated nickel foam electrode. This increment was affiliated with an electrochemically active surface area which increased by 87.1%, where Tafel analysis indicated that the acid treated, MoS2-coated electrodes facilitates the initial water dissociation step of the hydrogen evolution reaction with greater ease. Similar effects were also discovered for acid treated PtIr(1:3)/C-coated nickel foam substrates, albeit with less pronounced effects. Stability was also improved where the degradation rate was reduced by 18.9% for the acid treated, MoS2-coated electrodes. This proves the utility of acid washing nickel foam electrodes.

Zinc protection of galvanized steel is initially dissolved in alkaline solutions. However, passive layer is formed over time which protects the steel from corrosion. The behavior of galvanized steel exposed to strong alkaline solutions (pH values of 12.7) with a fixed concentration of sulfate ion of 0.04M is studied. Electrochemical measurement techniques such as corrosion potential, linear polarization resistance and electrochemical impedance spectroscopy are used. Synergistic effect of sulfate ion is also studied together with other anions such as chloride Cl- or bicarbonate ion HCO3- and with other cations such as calcium Ca2+, ammonium NH4+ and magnesium Mg2+. Presence of sulfate ions can depassivate the steel, leading to corrosion density of 0.3 µA/cm2 at the end of the test. The presence of other ions in the solution increases this effect. The increase in corrosion density caused by cations and anions responds to the following order (greater to lesser influence): NH4+&gt;Ca2+&gt;Mg2+ and HCO3- &gt;Cl- &gt;SO42-.

Presepsin is a diagnostic and prognostic biomarker of sepsis; however, elevated presepsin levels have also been documented without sepsis. This study aims to retrospectively analyze the laboratory parameters and Sequential Organ Failure Assessment (SOFA) score affecting presepsin levels in 567 patients. Some patients with elevated presepsin levels exhibited renal dysfunction or elevation of biliary enzymes despite a low SOFA score. The univariate regression analysis revealed a close correlation between presepsin levels and SOFA score, serum creatinine (CRE), blood urea nitrogen, and biliary enzymes. In addition, a multivariate regression analysis revealed that SOFA score, alkaline phosphatase (ALP), and CRE independently affected presepsin levels significantly. The analysis of covariance (ANCOVA) revealed that presepsin levels were significantly higher in patients with hepatobiliary disease. Besides, we found that patients who presented with the dilatation of intra- or extrahepatic bile ducts and the elevation of ALP or total bilirubin exhibited remarkable high presepsin levels in the bile. Furthermore, the presepsin production in the liver’s Kupffer cells was established by immunostaining in patients who received surgical liver resection. Overall, this study elucidates that biliary enzymes’ elevation affects presepsin levels, presepsin exists in high concentrations in the bile, and is positive in Kupffer cells.

Pyrochlore group minerals are the main raw phases in granitic rocks of the Katugin complex-ore deposit that stores Nb, Ta, Y, REE, U, Th, Zr, and cryolite. They are of three main generations: primary magmatic (I), early postmagmatic (II), and supergene (III) pyrochlores. The primary magmatic phase (generation I) is fluornatropyrochlore with high concentrations of Na2O (to 10.5 wt.%), F (to 5.4 wt.%) and REE2O3 (to 17.1 wt.%) but low CaO (0.6-4.3 wt.%), UO2 (to 2.6 wt.%), ThO2 (to 1.8 wt.%), and PbO (to 1.4 wt.%). Pyrochlore of this type is very rare in nature and limited to a few occurrences, such as rare-metal deposits of Nechalacho in syenite and nepheline syenite (Canada) and Mariupol in nepheline syenite (Ukraine). It may have crystallized synchronously with or slightly later than melanocratic minerals (aegirine, biotite, and arfvedsonite) at the late magmatic stage when Fe from the melt became bound making impossible the formation of columbite. Second generation pyrochlore formed at the early postmagmatic stage of the Katugin deposit. It differs from that of first generation in lower Na2O concentrations (2.8 wt.%), relatively low F (4 wt.%), and les occupancy of the A and Y sites at similar contents of other components. Generation III pyrochlore is a product of supergene alteration processes. It is compositionally heterogeneous and contains K, Ba, Pb, Fe, and significant Si concentrations but low Na and F. Its compositions mostly fall within the filed of hydro- and kenopyrochlore.

In this paper, we first report that WO_x contained nanoalloys exhibit stable electrocatalytic performance in alkaline media, though bulk WO₃ are easy to be dissolved in NaOH solutions. Carbon supported oxide-rich Pd-W alloy nanoparticles (PdW/C) with different Pd:W atom ratios were prepared by reduction-oxidation method. Among the catalysts, the oxide-rich Pd0.8W0.2/C (Pd/W = 8:2, atom ratio) exhibits the highest catalytic activity for oxygen reduction reaction. The X-ray photoelectron spectroscopy data shows that ~40% of Pd atoms and ~60% of the W atoms are in their oxides form. The Pd 3d_5/2 peaks in oxide-rich Pd-W nanoalloys are positive shift compared with that of Pd/C, which indicates the electronic structure of Pd is affected by the strong interaction between Pd and W/WO₃. Compare to Pd/C, the onset potential of oxygen reduction reaction at the oxide-rich Pd_0.8W_0.2/C is positive shifted. The current density (mA·mg Pd⁻¹) at the oxide-rich Pd_0.8W_0.2/C is ~1.6 times of that at Pd/C. The oxide-rich Pd_0.8W_0.2/C also exhibits higher catalytic stability than Pd/C, which demonstrate that it is a prospective candidate for the cathode of fuel cells operated with alkaline electrolyte.

Hazelnut, pistachio and cashew are tree nuts with health benefits but also with allergenic properties being prevalent food allergens in Europe. The allergic characteristics of these tree nuts after processing combining heat, pressure and enzymatic digestion were analyzed through in vitro (Western blot and ELISA) and in vivo test (Prick-Prick). In the analyzed population, the patients sensitized to Cor a 8 (nsLTP) were predominant over those sensitized against hazelnut seed storage proteins (Sprot, Cor a 9 and 14), which displayed higher IgE reactivity. The protease E5 effectively hydrolyzed proteins from hazelnut and pistachio, while E7 was efficient for cashew protein hydrolysis. When combined with pressured heating (autoclave and Controlled Instantaneous Depressurization (DIC)), these proteases notably reduced the allergenic reactivity. The combination of DIC treatment before enzymatic digestion resulted in the most effective methodology to drastically reduce or indeed eliminate the allergenic capacity of tree nuts.

Hydrogen peroxide (H2O2) is an essential analyte for detecting neurodegenerative diseases and in-flammatory processes and plays a crucial role in pharmaceutical, food industry, and environmental monitoring. However, conventional H2O2 detection methods have drawbacks such as lengthy analysis time, high costs, and bulky equipment. Non-enzymatic sensors have emerged as promising alternatives to overcome these limitations. In this study, we introduce a simple, portable, and cost-effective non-enzymatic electrochemical sensor based on carbon black (CB) and silver nano-particle-modified δ-FeOOH (Ag/δ-FeOOH), integrated into a disposable electrochemical cell (DCell). Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and electrochemical impedance spectroscopy (EIS), confirmed successful CB and Ag/δ-FeOOH immo-bilization on the DCell working electrode. Electrochemical investigations revealed that the DCell-CB//Ag/δ-FeOOH sensor exhibited an approximately twofold higher apparent heterogene-ous electron transfer rate constant than the DCell–Ag/δ-FeOOH sensor, capitalizing on CB ad-vantages. Moreover, the sensor displayed excellent electrochemical response for H2O2 reduction, boasting a low detection limit of 22 µM and a high analytical sensitivity of 214 μA mM-1 cm-2. Notably, the DCell-CB//Ag/δ-FeOOH sensor exhibited outstanding selectivity for H2O2 detection, even in potential interferents such as dopamine, uric acid, and ascorbic acid. Furthermore, the sensor demonstrated its suitability for monitoring H2O2 in complex biological samples, as evidenced by H2O2 recoveries ranging from 92% to 103% in 10% fetal bovine serum. These findings underscore the considerable potential of the DCell-CB//Ag/δ-FeOOH sensor for precise and reliable H2O2 monitoring in diverse biomedical and environmental applications.

Sulfite and kraft pulping are two principal methods of industrial delignification of wood. In recent decades, those have been considered as possibilities to pretreat recalcitrant wood lignocellulosics for enzymatic hydrolysis of polysaccharides and subsequent fermentation of obtained sugars to valuable bioproducts. Current work compares chemistry and technological features of two different cooking processes in the preparation of polysaccharide substrates for deep sacchari-fication with P. verruculosum glycosyl hydrolases. Bleached kraft and sulfite pulps were subjected to hydrolysis with enzyme mixture of high xylanase, cellobiohydrolase and β-glucosidase activities at a dosage of 10 FPU/g of dry pulp and fiber concentration of 2.5, 5 and 10%. HPLC was used to analyze soluble sugars after hydrolysis and additional acid inversion of oligomers to monosaccharides. Kraft pulp demonstrated higher pulp conversion after 48 h (74-99%), mostly resulted from deep xylan hydrolysis. Sulfite-pulp hydrolysates, obtained in similar conditions, due to higher hexose concentration (more than 50 g/L), had higher fermentability for industrial strains producing alcohols, microbial protein or organic acids. Along with saccharification, enzymatic modification of non-hydrolysed residues occurred, which led to decreased degree of polymerization and composition changes in two industrial pulps. As a result, crystallinity of kraft pulp increased by 1.3%, which opens possibilities for obtaining new types of cellulosic products in pulp and paper industry. The high adaptability and controllability of enzymatic and fermentation processes creates prospects for the modernization of existing factories.

Enzymatic polyethylene terephthalate (PET) recycling processes are gaining interest for their low environmental impact, use of mild conditions, and specificity. Furthermore, PET hydrolase enzymes are continuously being discovered and engineered. In this work, we studied a PET hydrolase (PET2), initially characterized as an alkaline thermostable lipase. PET2 was produced in a fusion form with a 6-histidine tag in the N-terminal. The PET2 activity on aromatic terephthalate and new indole-based polyesters was evaluated using polymers in powder form. Compared with IsPETase, an enzyme derived from Ideonella sakaiensis, PET2 showed a lower PET depolymerization yield. However, interestingly, PET2 gave significantly higher polybutylene terephthalate (PBT) and polyhexylene terephthalate (PHT) depolymerization yields. A clear preference was found for aromatic indole-derived polyesters over non-aromatic ones. No activity was detected on Akestra™, an amorphous copolyester with spiroacetal structures. Docking studies suggest that a narrower and more hydrophobic active site reduces its activity on PET but favours its interaction with PBT and PHT. Understanding the enzyme preferences of polymers will contribute to their effective use to depolymerize different types of polyesters.

The purpose of this study was to investigate the effect that Glycine max hydrolyzed with enzymes from Bacillus velezensis KMU01 has on dextran sulfate sodium (DSS)-induced colitis in mice. Hydrolysis improves functional health through the bioconversion of raw materials and increase in intestinal absorption rate and antioxidants. Therefore, G. max was hydrolyzed in this study using a food-derived microorganism, and its anti-inflammatory effect observed. Enzymatically hydrolyzed G. max (EHG) was orally administered once daily for four weeks before DSS treatment. Colitis was induced in mice through consumption of 5% (w/v) DSS in drinking water for eight days. Results showed that EHG treatment significantly alleviated DSS-induced body weight loss and decreased the disease activity index and colon length. In addition, EHG markedly reduced tumor necrosis factor-a, interleukin (IL)-1b, and IL-6 production, and increased that of IL-10. EHG improved DSS-induced histological changes and intestinal epithelial barrier integrity in mice. Moreover, we found that the abundance of 15 microorganisms changed significantly; that of Proteobacteria and Escherichia coli, which are upregulated in patients with Crohn’s disease and ulcerative colitis, decreased after EHG treatment. These results suggest that EHG has a protective effect against DSS-induced colitis and is a potential candidate for colitis treatment.

Crown of thorns starfish (Acanthaster planci) are coral predators with advantages of having toxicity in their venom and tissue regeneration capabilities. With all these characteristics, only a handful of studies have highlighted the association of microorganisms with this organism. Crown of thorns starfish are common in Fiji and their analyses of microbial diversity for secondary metabolites could be of great interest to the scientific community. This study is an attempt to investigate Fijian-based A. planci for their venom and associated actinomycetes antibacterial activity and further identify the type of enzymes present in the crude venom extract. The CoTS venom extract (0.192 g) harbor enzymes such as gelatinase, caesinase, and amylase. An abundant and potent actinomycete strain, represented as FJA1 showed antibacterial activity against Enterococcus faecium with an inhibition zone of 10 mm. Moreover, all pathogenic test microorganisms were resistant against concentrations of 500 µg and 1 mg of A. planci venom extract.

The main intention of the present work was to investigate the ability of cellulose-degrading enzymes (C-DE) to release fatty acids (FAs) from complex matrices of cereal by-products during enzymatic hydrolysis (EH). For this purpose, three types of cereal bran (CB), i.e., wheat, rye, and oat were used as a lignocellulose substrate for three commercially available hydrolytic enzymes, i.e., Viscozyme L, Viscoferm, and Celluclast 1.5 L. The yield and composition of FAs after EH was assessed and confronted with the yield obtained after either conventional Soxhlet extraction or alkaline-assisted hydrolysis (A-AH) with 10% KOH in 80% MeOH and subsequent liquid-liquid extraction. The experimental results demonstrated that up to 6.3% and 43.7% higher total FAs yield can be achieved within EH of rye bran using Celluclast 1.5 L than by A-AH and Soxhlet extraction, respectively. However, the application of Viscoferm for EH of wheat bran ensured up to 7.7% and 13.4% higher total FAs yield than A-AH and Soxhlet extraction, respectively. The concentration of essential linolenic acid (C18:3) in lipids extracted after EH of rye bran with Celluclast 1.5 L was up to 24.4% and 57.0% higher than in lipids recovered by A-AH and Soxhlet extraction, respectively. In turn, the highest content of linolenic in wheat bran lipids was observed after EH with Viscoferm and Viscozyme L, ensuring 17.0 and 13.6% higher yield than after A-AH, respectively. SEM analysis confirmed substantial degradation of CB matrix promoted by the ability of C-DE to act specifically on 1,4-β-D-glycosidic bonds in cellulose and on 1,2-α-,1,3-α-, and 1,5-α-L- arabinofuranoside and 1,4-β-D-xylosidic bonds in arabinoxylans, arabinans, and other arabinose-containing hemicelluloses. Structural alteration in cells integrity greatly contributed to the release of bound FAs and their better transfer into the extraction solvent. It has been shown that the proposed process of EH can be used for the efficient release of FAs from the CB matrix more sustainably and with a safer profile, thereby representing the further sustainable production of FAs for certain purposes.

Self-assembled structures mostly arises through enzyme-regulated phenomena in nature under persistent conditions. Enzymatic reactions are one of main biological processes in fabrication and construction of supramolecular hydrogel networks required for biomedical applications. The enzymatic processes provide a unique opportunity to integrate hydrogel formation. In most of cases, structure and substrates of hydrogels are adjusted by enzyme catalysis due to the chemo-, regio- and stereo-selectivity of enzymes. Hydrogels processed by using various enzyme schemes showed remarkable characteristics as dynamic frames for cells, bioactive molecules and drugs in biomedical applications. A novel class of enzyme-mediated crosslinking hydrogels mimics the extracellular matrices by displaying unique physicochemical properties and functionalities like water-retention capacity, drug loading ability, biodegradability, biocompatibility, biostability, bioactivity, optoelectronic properties, self-healing ability, shape memory ability. In recent years, many enzymatic systems investigated hydrogel cross-linking. Results of biocompatible hydrogel products show that these mechanisms of crosslinking can fulfill requirements for variety of biomedical applications including tissue engineering, wound healing and drug delivery.

Protein hydrolysates show great promise as bioactive food and feed ingredient and for valorization of side-streams from e.g. the fish processing industry. This study characterizes bulk emulsifying, foaming, and in vitro antioxidative properties of hydrolysates derived from cod frame by application of Alcalase and Neutrase, individually and sequentially as well as the influence of heat-treatment prior to hydrolysis. We present a novel approach that utilizes proteomics data for calculation of weighted mean peptide properties (length, molecular weight, and charge) and peptide-level abundance estimation. Using subsequent bioinformatic prediction of biofunctional properties to describe observed bulk properties, we are able to provide an in-depth hydrolysate characterization not previously seen. All hydrolysates displayed comparable or higher emulsifying activity and stability than sodium caseinate. Heat-treatment significantly increased stability but showed a negative effect on the activity and degree of hydrolysis. Combining peptide abundance with predicted emulsifying activity, we were able to identify several peptides that are likely linked to the observed differences in bulk emulsifying properties. In general, decreased hydrolysis resulted in significantly higher chelating activity, while the opposite was observed for radical scavenging activity. The study highlights the prospects of applying proteomics and bioinformatics for hydrolysate characterization and in food protein science.

Periodontitis is microbial infection affecting periodontium, the tooth supporting structure and affects >743 million people worldwide. Neural crest-derived stem cells (NCSCs) hold the promise to regenerate the damaged periodontium. These cells have been identified within adult adipose tissue, periodontal ligament, and palatal tissue. Typical enzymatic isolation protocols are expensive, time consuming and often not clinically compliant. Enzyme-free, mechanical dissociation has been suggested as an alternative method of generating cell suspensions required for cell separation and subsequent expansion ex vivo. In our study, samples of rat skeletal muscle tissue were used to appraise the suitability of a novel mincing method of mechanical dissociation against enzymatic digestion with collagenase and dispase. Skeletal muscle is readily available and has been shown to contain NCSC populations. We used a Rigenera-Human Brain Wave^® prototype mincer to produce a suspension of skeletal muscle-derived cells modeling NCSCs. We have compared the resulting cell cultures produced via mechanical dissociation and enzymatic dissociation, producing single cell suspensions suitable for Magnetic Cell Sorting (MACs) and Fluorescence-activated cell sorting (FACS). Despite the Countess Automated Cytometry data demonstrating that cell suspensions produced by mechanical dissociation (n=24) contain on average 26.8 times as many viable cells as enzymatic cell suspensions (n=18), enzymatic suspensions produced more successful cell cultures. Spheroids and subsequently adherent cells formed from 4 enzymatic cell suspensions (44.4%) vs. 1 mechanical cell suspension (8.3%). Enzymatic digestion protocols formed spheroids faster and more plentifully than mechanical cell suspensions. Adherent cells and spheroids isolated via both methods appear morphologically similarly to NCSCs from our previous studies.

Non-enzymatic glucose sensing is a crucial field of study because of the current market demand. This study proposes a novel design of glucose sensor with enhanced selectivity and sensitivity by using graphene Schottky diodes, which is composed of Graphene/Platinum Oxide/n-Silicon heterostructure. The sensor was tested with different glucose concentrations and interfering solutions to investigate its sensitivity and selectivity. Different structures of the device were studied by adjusting the platinum oxide film thickness to investigate its catalytic activity. It was found that the film thickness plays a significant role in the efficiency of glucose oxidation and hence in overall device sensitivity. Moreover, theoretical investigations were conducted using Density Function Theory (DFT) to better understand the detection method and the origins of selectivity. The working principle of the sensors puts it in a competitive position with other non-enzymatic glucose sensors. DFT calculations provided a qualitative explanation of the charges distributed across the graphene sheet within a system of a platinum substrate with D-glucose molecules above. The proposed graphene/PtO/n-Si heterostructure has proven to satisfy these factors, which opens the door for further developments of more reliable non-enzymatic glucometers for continuous glucose monitoring systems.

The performance of modified electrode of nanocomposite film consisting of polypyrrole-chitosan-titanium dioxide (Ppy-CS-TiO2) has been explored as non-enzymatic glucose biosensors. The synergy effect of TiO2 nanoparticles and conducting polymer on the current response of electrode resulted in higher sensitivity for nanocomposite modified electrode. The incorporation of TiO2 nanoparticles in the nanocomposite films were confirmed by XPS spectra. The FESEM and HR-TEM provided more evidences for the presence of TiO2 in Ppy-CS structure. Glucose biosensing properties were determined by amperommetry and cyclic voltammetry (CV) methods. The interfacial properties of nanocomposite electrodes were studied by electrochemical impedance spectroscopy (EIS). The developed biosensors showed a good sensitivity over the liner range of 1-14 mM with a detection limit of 614 μM for glucose. It also exhibited good selectivity and long term stability with no interference effect. The Ppy-CS-TiO2 nanocomposites film presented high electron transfer kinetics.

This study evaluated batch fermentation modes, namely, separate hydrolysis and fermentation (SHF), Quasi-simultaneous saccharification and fermentation (Q-SSF), and simultaneous saccharification and fermentation (SSF), and fermentation conditions, i.e., enzyme and yeast loadings, nutrient supplementation and sterilization, on high titer bioethanol production from SPORL-pretreated Douglas-fir forest residue without detoxification. The result indicated Q-SSF and SSF were obviously superior to SHF operation in terms of ethanol yield. The enzyme loading showed a strong positive correlation between enzyme loading and the ethanol yield. The nutrient supplementation and sterility was not necessary for ethanol production from SPORL-pretreated Douglas-fir. The yeast loading showed no significant influence on the ethanol yield for typical SSF conditions. The terminal ethanol titer of 43.2 g/L, or 75.1% theoretical based on glucose, mannose, and xylose theoretical was achieved when SSF was conducted at the condition of following: whole slurry solids loading of 15%, enzyme loading of 20 FPU/g glucan, 1.8 g/kg (wet) yeast loading, without nutrition supplementation and sterilization, at 38°C, on shake flask at 150 rpm for 96h. It is believed that with mechanical mixing, enzyme loading can be substantially reduced with affect ethanol yield by using a long fermentation time.

A survey of the trends in metal-ligand coordination and hydrogen bonding has been carried out on complexes of singly deprotonated cyanuric acid CY− and alkaline earth metals, synthesised from aqueous solution and characterised by X-ray crystallography. Involvement of cyanurate in the metal coordination increases from Mg through Ca and Sr to Ba relative to coordination by water, in parallel with the increasing ionic radius and coordination number. The incidence of bridging of metal centres by both water and cyanurate also increases in this series. The Mg complex contains hexaaqua-coordinated cations, uncoordinated CY− anions, and additional water molecules. Ca and Sr complexes feature polymeric chains of coordinated metal ions, the Ca complex with uncoordinated anions and the Sr complex with all potential ligands coordinated. The Ba complex has a two-dimensional coordination network. Extensive hydrogen bonding plays a key role in generating a three-dimensional network in all four structures. The competition between cyanurate and water for coordination to the alkaline earth metal cations, and that between coordination and hydrogen bonding propensities of the cyanurate anion, appear to be finely balanced, with the structural outcomes depending on the relative sizes and degrees of hardness of the four cations of the group.

The widespread use of epoxy resin (ER) in industry, owing to its excellent properties, aligns with the global shift toward greener resources and energy-efficient solutions, where utilizing metal oxides in 3D printed polymer parts can offer extended functionalities across various industries. ZnO concentrations in polyurethane acrylate composites impacted adhesion and thickness of DLP samples, with 1 wt.% achieving a thickness of 3.99±0.16 mm, closest to the target thickness of 4 mm, while 0.5 wt.% ZnO samples exhibited the lowest deviation in average thickness (±0.03 mm). Tensile strength in digital light processed (DLP) composites with ZnO remained consistent, ranging from 23.29 MPa (1 wt.%) to 25.93 MPa (0.5 wt.%), with an increase in ZnO concentration causing a reduction in tensile strength to 24.04 MPa and a decrease in the elastic modulus to 2001 MPa at 2 wt.% ZnO. The produced DLP samples, with their good corrosion resistance in alkaline environments, are well-suited for applications as protective coatings on tank walls. Customized DLP techniques can enable their effective use as structural or functional elements, such as in Portland cement concrete walls, floors and ceilings for enhanced durability and performance.

Saline water irrigation contributes significantly to forage yield. However, the salinity threshold for safe saline water irrigation of tall wheatgrass in coastal saline-alkaline land remains unclear. In this study, 2 g L‒1, 3 g L‒1, 4 g L‒1, 5 g L‒1, and 8 g L‒1 saline waters were used for irrigation. Two irrigations with 2+3 g L‒1 saline waters produced the highest yield, followed by one irrigation with 4 g L‒1 or 5 g L‒1 saline water. After rainfall’s leaching, the soil electrical conductivity (EC1:5) reduced by 41.7%‒79.3% for the saline water irrigation treatments. In combination with saline water irrigation, plastic film mulching can be used for sward establishment of seed propagated tall wheatgrass. However, irrigation with high salinity of drainage water enhanced the risk of plant death. Further, a pot experiment demonstrated that irrigation with 5 g L‒1 saline water led to the least reduction of forage yield and the highest crude protein content in leaves. However, the plants irrigated with ≥7 g L‒1 saline water enhanced soil salinity and reduced plant height, leaf size, and gas exchange rate. Conclusively, one irrigation with ≤5 g L‒1 saline water at the end of April or early May could be acceptable to maximize the forage yield of tall wheatgrass and minimize soil salinization risk in the coastal saline-alkaline land around the Bohai Sea.

Due to the severe environmental impact of the CO2 emissions associated with the production of Ordinary Portland Cement (OPC) and the increasing demand for this commodity material, the development of alternative products has become a global concern. One alternative to OPC, or alitic-based clinkers, are amorphous-wollastonitic low calcium hydraulic binders (AWLCs). This new class of hydraulic binders, described in the literature for the first time in 2015, may significantly reduce the CO2 emissions associated with its production, resulting from its lower calcium content, but also from the fact that its production technology can be fully electrified. In this paper it is provided a state-of-the-art review, providing a comprehensive description on the latest research, summarizing both the physico-chemical and mechanical characteristics for this type of hydraulic binders, as well as possible routes for its production at an industrial scale.

Efficient oxygen evolution reaction (OER) electrocatalysts are highly desired in the field of water electrolysis and rechargeable metal-air batteries. In this study, a chelate polymer, composed of copper (II) and dithiooxamide, was used to derive an efficient catalytic system for OER. Upon potential sweep in 1M KOH, copper (II) centers of the chelate polymer were transformed to CuO and Cu(OH)2. The carbon-dispersed CuO nanostructures formed a nanocomposite which exhibits an enhanced catalytic activity for OER in alkaline media. The nanocomposite catalyst has overpotential of 280 mV (at 1 mA/cm2) and a Tafel slope of 81 mV/dec in 1M KOH solution. It has a seven-fold higher current than IrO2/C electrode, per metal loading. A catalytic cycle is proposed, in which, CuO undergoes electrooxidation to Cu2O3 that further decomposes to CuO with releasing oxygen. This work reveals a new method to produce an active nanocomposite catalyst for OER in alkaline media using a non-noble metal chelate polymer and a porous carbon. This method can be applied to the synthesis of transition metal oxide nanoparticles used in the preparation of composite electrodes for water electrolyzers and can be used to derive cathode materials for aqueous-type metal-air batteries.

DNA methylation is one of the epigenetic mechanisms which have been implicated in cellular differentiation, ageing and disease development. The effect of hypomethylating drug 5-aza-2´deoxycytidine (5-aza dC) on the biosynthetic profile of caudal region chondrocytes from chick sternum was studied in detail. The chondrocytes in culture were treated with varying doses of 5-aza dC for 48h and maintained subsequently without the treatment and harvested at selected time points for analysis of growth and differentiation status. 15µg/ml of 5-aza dC showed optimum Concentration at which there was a significant increase in DNA synthesis and RNA synthesis as per cell basis. There was also a significant increase in total protein synthesis and collagen synthesis as per cell basis at this concentration. This optimal concentration also showed to up regulate the gene expression of Type X collagen and alkaline phosphatase, which are the marker of hypertrophic chondrocyte expression. These results further support the notion that methylation is the major epigenetic factor controlling the differentiation and maturation of chondrocytes.

Soil extracellular enzyme activity (EEAs) and enzymatic stoichiometry (ES) can provide a crucial indication of changes in soil ecosystem's nutrient availability and the microbial resource limitations. However, the changing characteristics of soil EEAs and ES at different stages of the native succession process and their key drivers are unclear. In order to investigate the soil EEAs, ES and driving factors of soil under vegetation at different succession stages, we adopted the "spatio-temporal substitution" method to collect the surface soil of bryophyte community, herbaceous community, shrub community and tree community in the new volcanic lava platform of Wudalianchi Volcanic Nature Reserve. We measured seven soil EEA, including carbon(C)-acquiring enzyme (β-1,4-glucosidase (BG)), N-acquiring enzymes (β-N-acetyl-glucosaminidase (NAG) and leucine aminopeptidase (LAP)) and phosphorus (P)-acquiring enzyme (acid phosphatase (AP)) activities. The length and angle of vectors defined by ratios of enzyme activities (BG/(NAG + LAP) vs. BG/AP) were used to indicate relative microbial investments in C- (length), and N- and P- (angle) acquiring enzymes. Our results showed that the contents of TC, TN, TP, MBC, DOC and NO3-N in shrub community soil were significantly higher than those in bryophyte, herb and tree communities, and increased by 441%, 246%, 137%, 5570%, 12% and 484%, respectively. The highest soil EEA of C-, N- and P-acquiring were found in shrub community, and the soil EEAs/MBC of C-, N- and P-acquiring were the highest in bryophyte community. Enzyme C:N, C:P and N:P ratios increased progressively in the order of bryophyte, herb and shrub community, but the enzyme C:N, C:P and N:P ratios of tree community were both far less than shrub community. Vector lengths increased progressively in the order of bryophyte (1.16), herb (1.27), tree (1.29) and shrub (1.40), and Vector angles decreased progressively in the order of bryophyte (49.15°), herb (45.65°), Tree (45.31°) and shurb (44.54°), suggested that as succession progresses, soil microbial nutrients transforms from P limitation (angle＞45°) to N limitation (angle＜45°). Redundancy analysis showed that TC, TN, EC and C:N were important drivers of variation in soil EEAs and ES in vegetation at different succession stages. Our findings highlight that the primary succession process cause nutrient limitation transformation. Soil ES might be a sensitive indicator mediated by soil microorganisms to the relative resource limitation at different stages of the primary succession process.