The relation between CO2 emissions and atmospheric CO2 concentration has traditionally been treated with more or less complex models with several boxes. Our approach is motivated by the question of how much CO2 must necessarily be absorbed by sinks. Observations lead to the model assumption, that carbon sinks like oceans or biosphere are linearly dependent on CO2 concentration on a decadal scale. In particular this implies the falsifiable hypothesis that oceanic and biological CO2 buffers have not significantly changed in the past 50 years and are not saturated in the forseeable future. The simple model with 2 parameters explains very well the CO2 emission and historical CO2 concentration data. The model gives estimates of the natural emissions, the pre-industrial CO2 equilibrium concentration levels, the half-life time of an emission pulse, and the future CO2 concentration level from a given emission scenario. This is validated by an ex-post forecast of the last 20 years. The important result is that with the stated polices scenario of the IEA future CO2 concentrations will not rise above 475 ppm. The model is compared with the Carbon modul of the Bern model, mapping their complex IRFs to a single time variant parameter.

The path towards decarbonization requires a progressive adaptation of all refrigeration systems, but only stationary ones have been intensely studied to improve their environmental performance. However, refrigerated transport is a vital piece of the cold chain, and it must be considered in the green transition. In this paper, we propose a model for a hybrid refrigerated van that includes photovoltaic panels and electric batteries to decrease total greenhouse gas emissions from the engine. Thermal, electrical, and battery sub-models are considered and integrated into the comprehensive hybrid solar-powered refrigerated van model. Different technologies are compared in economic terms, including Lithium and Lead-acid batteries and three different types of photovoltaic panels. The model was validated regarding van fuel consumption, showing a 4% deviation. Single and multiple delivery scenarios are considered to assess the energetic, economic, and environmental benefits. Monthly CO2,e emissions could be reduced to 20% compared to a standard refrigerated van. Despite the environmental benefits provided by this sustainable solution, the payback period is still too long (above 20 years) because of the necessary investment to adapt the vehicle and considering fuel and electricity prices currently.

In this article, we aim to show the capabilities, benefits, as well as restrictions, of three different air quality-related information sources, namely the Sentinel-5Precursor TROPOspheric Monitoring Instrument (TROPOMI) space-born observations, the Multi-Axis Differential Optical Absorption Spectroscopy (MAX-DOAS) ground-based measurements and the LOng Term Ozone Simulation – EURopean Operational Smog (LOTOS-EUROS) chemical transport modelling system simulations. The tropospheric NO2 concentrations between 2018 and 2021 are discussed as air quality indicators for the Greek cities of Thessaloniki and Ioannina. Each dataset was analysed in an autonomous manner and, without disregarding their differences, the common air quality picture that they provide is revealed. All three systems report a clear seasonal pattern, with high NO2 levels during winter-time and lower NO2 levels during summer-time, reflecting the importance of photochemistry in the abatement of this air pollutant. The spatial patterns of the NO2 load also showed, in both space-born observations and model simulations, the undeniable variability of the NO2 load within the urban agglomerations. The diurnal variability was furthermore clearly identified by the ground-based measurements, which also unquestionably revealed a Sunday minimum NO2 load effect, alongside the rest of the sources of air quality information. Within their individual strengths and limitations, the space-born observations, the ground-based measurements and the chemical transport modelling simulations, demonstrate unequivocally their ability to report on the air quality situation in urban locations.

Greenhouse Gases (GHG) emissions from dairy farms are significant contributors to global warming. However much of the published work on GHG reduction is focused on either Methane (CH4) or Nitrous Oxide (N2O), with few, if any, considering the interactions that changes to farm systems can have on both gases. This paper takes the raw data from a year of activity on a 300 cow commercial dairy farm in Northern Ireland to more accurately quantify the GHG sources by use of a simple predictive model based on IPCC methodology. Differing herd management policies are examined together with the impact of integrating Anaerobic Digestion (AD) into each farm system. Whilst significant success can be predicted in capturing CH4 and Carbon Dioxide (CO2) as biogas and preventing N2O emissions, gains made can be lost in a subsequent process negating some or all of the advantage. The process of extracting value from the captured resource is discussed in the light of current farm parameters together with indications of other potential revenue streams. However, this study has concluded that despite the significant potential for GHG reduction, there is little incentive for widespread adoption of manure based farm scale AD in the UK at this time.

It is widely discussed that growth of GDP has a vague impact on environmental pollution due to the emissions of carbon dioxide from consumed fossil fuels in production, transportation and power generation, and creation of required instruments to control environmental pollution as well. Due to the fact that environmental pollution can be a reason of mortality increase in a society, the main purpose of this study is to investigate the relationship between economic growth, fossil fuel consumption, mortality (from cardiovascular disease, cancer, diabetes and chronic respiratory disease) and environmental pollution using Generalized Method of Moments (GMM) estimation technique in the case of CIS member states over the period of 1993-2018. The major results revealed CO2 emissions in in the region of CIS have a positive effect on increase of mortality from cardiovascular disease, cancer, diabetes and chronic respiratory disease. In regards to fossil fuel consumption, the estimation proved that this variable affects mortality from cardiovascular disease, cancer, diabetes and chronic respiratory disease positively. In addition, we found effect of economic growth, population growth and inflation rate positively, while any improvement in human development index (HDI) has a negative effect on increase of mortality from cardiovascular disease, cancer, diabetes and chronic respiratory disease in the CIS region. It is recommended that the CIS member states carry out different policies to improve energy transition indicating movement from fossil fuel energy sources to renewable ones. Moreover, we recommend the CIS member states to enhance various policies for easy access to the electricity from green sources and increase of renewable supply through improved technologies, sustainable economic growth, and increase of using green source in daily social life.

Low carbon cities are increasingly forming a distinct strand of sustainability literature. Models have been developed to measure the performance of low carbon cities. The purpose of this paper is to formulate a strategy-based model to evaluate current performance and predict future conditions of low carbon cities. It examines the dynamic interrelationships between key performance indicators (KPIs), induces changes to city plan targets and then instantly predicts the outcome of these changes. Designed generic and flexible, the proposed model shows how low carbon targets could be used to guide the transformation of low carbon cities under four strategies: (1) passive intervention, (2) problem solving, (3) trend modifying and (4) opportunity seeking. Further, the model has been applied to 17 cities and then tested on 5 cities: London, New York, Barcelona, Dubai and Istanbul. The paper concludes with policy implications to realign city plans and support low carbon innovation.

Traffic source emissions inventories for the rapidly growing West African urban cities are necessary for better local characterization of vehicle emissions released into these cities atmosphere. This study based on local field campaign in a representative site of anthropogenic activities over West African cities such as Yopougon (Abidjan, Côte d'Ivoire) during 2016, provided useful information on vehicle type and age, traveling time, fuel type and amount for fuel consumption estimation. Also, high traffic flow of personal car were recorded on highway, boulevard and backstreet whereas high flows of intra-communal sedan taxi are recorded on main and secondary roads. In addition, the highest daily fuel consumption value of 56 L.day^-1 was recorded in heavy vehicle while the lowest value of 15 L.day^-1 is recorded for personal car using gasoline. This study will be useful for the improvement of uncertainties related to the different databases used to estimate inventories emissions either national or international reports. This work provides useful information for future studies on urban air quality, climate and health impacts assessment in African cities. It may also be useful for policy makers to support implementation of emission reduction policy in West African cities.

The gap of standardization for conducted and field coupled electromagnetic interferences (EMI) in the 2–150 kHz frequency range can lead to Electromagnetic Compatibility (EMC) problems. This is caused by power systems such as PWM controlled rectifiers, photovoltaic inverters or charging battery units in electric vehicles. This is a very important frequency spectral due to interferences generate in a wide range of dives and, specifically, communication problems in the new technologies and devices incorporated to the traditional grid to convert it into Smart Grid. Consequently, it is necessary to provide new solutions to attenuate this kind of interferences, which involve finding new materials able to filter the electromagnetic noise. This contribution is focused on characterizing the performance of different cable ferrite compositions in order to determine the effectiveness of most common materials such as MnZn and NiZn and a new range based on nanocrystalline solutions. This analysis procedure is carried out through two methods: theoretical method by determining the insertion loss through measuring impedance parameter and proposing a new empirical technique based on measuring directly the insertion loss parameter. Therefore, the main aim of this characterization process is to determine the performance of these cable ferrites to reduce the interferences in this controversial frequency range. From the results obtained, it is possible to deduce that nanocrystalline cable ferrites provide the best performance to filter the electromagnetic noise in the 2-150 kHz frequency range.

Predictive numerical models in the study of ground-borne vibrations generated by railway sys-tems have traditionally relied on the segmented approach of subsystems. In this approach, loads are individually applied, and the cumulative effect of rolling stock is obtained through superposi-tion. While this method serves to mitigate computational costs, it may not fully capture the com-plex interactions involved in ground-borne vibrations. Recent advancements in computational and software tools have enabled the development of more sophisticated vibrational pollution models. These advanced models encompass the entire dynamic system, from the rolling stock to the terrain, allowing for continuous simulations with a defined time step. Furthermore, the incorporation of computational contact tools between various ele-ments not only ensures temporal accuracy but also extends the analysis to the frequency domain. This paper explores the evolution of predictive numerical models in the context of ground-borne vibrations generated by trains on ballasted tracks. It highlights the shift from segmented models to continuous simulations, demonstrating the progressive advancement towards more comprehen-sive and accurate representations of railway-induced and generated vibrations in the track sur-roundings as an additional way of evaluate sustainability of infrastructures. In particular, this development of a numerical model from its inception aimed to expand upon ex-isting emission - prediction models by enriching the data with frequency-domain information. This approach has been driven by the aspiration to bridge the gap between numerical predictions and measured signals, striving for a higher level of accuracy in our obtained results. This model can predict the impact of a high-speed rail (HSR) vehicle passing on its own track. It possesses sufficient information in both the time and frequency domains to precisely characterize vibrations. This initiative marks a pivotal advancement, enabling us to more effectively capture the intricacies of ground-borne vibrations and their impact on the surrounding environment due to a deeper comprehension of the occurrences in the frequency domain, there's a heightened ca-pability to accurately characterize vibrations.

In many ports, the ship's speed is limited for the safety of navigation. At the same time, ship captains and port pilots choose the speed of the ship, but not higher than the permitted speed of the ship in the port, therefore the speed of the ship also depends on the experience of the ship captains and port pilots and the sailing conditions of the ship in specific conditions. Choosing the optimal speed of ships in port, including the effect of shallow depth, can reduce fuel consumption and ship emissions in ports, which is important for the development of green and sustainable ports. In all cases, shipping safety is the highest priority. The main objectives of the article are determining the optimal speed of ships in ports with low clearance, ensuring navigational safety, reducing fuel consumption and emissions, and at the same time creating a sustainable port. The article presents the methodology of optimal ship speed calculation, minimum ship controllable speed maintenance, fuel consumption and emission reduction methodology and their impact on sustainable and green maritime transport and port development. The developed methodology was tested on real ships and with the help of a calibrated simulator, sailing through harbor channels and harbor waters in low clearance conditions.

This paper reports modelling outcomes for improvements to building energy performance in Indonesia. Long-term climate effects due to building energy demands including carbon emissions are also considered. The global change assessment model (GCAM) was used to generate the related end-user building energy data, including socioeconomics for urban areas of Indonesia. As a comprehensive study, the total life cycle of carbon in the building sector and the concept of zero-carbon buildings, including energy efficiency, zero-emissions electricity and fuel switching options were considered. Building shell conductance (u-value) of building envelope, floor area ratio (FAR), air conditioner (AC) efficiency, electrical appliances (APLs) efficiency, rooftop photovoltaic (PV) performance and ground source heat pump (GSHP) systems were considered as parameters to mitigate carbon emissions under the operational energy category in GCAM. Carbon mitigation associated with the cement production process was considered in the raw material category. Urban population and labour productivity in Indonesia were used as base inputs with projected growth rates to 2050 determined from available literature. Low growth rate ‘LowRate’ and high growth rate ‘HighRate’ were considered as variable inputs for u-value, FAR, AC efficiency, APLs efficiency, and PV capacity factor to model emissions mitigation. The energy consumption of the GSHP was compared to the conventional reverse cycle ACs to identify the potential of the GSHP as a fuel-switching option. Only base input data were used for cement production process parameters without applying any variable inputs. GCAM base scenarios based on input data only (without modifying variable data) for the residential building sector in Indonesia were considered the benchmark for this study. Total potential carbon emissions mitigation was found to be 432 Mt CO2-e for the residential building sector in Indonesia over 2020-2050. It was found that an average of 24% carbon emissions mitigation could be achieved by 2020-30 and 76% in 2031-2050.

Lifetime cancer risk characterization of ambient PM-bound carcinogenic metals and polycyclic aromatic hydrocarbons (PAHs) were examined in the cities of Los Angeles (USA), Thessaloniki (Greece) and Milan (Italy), which share similar Mediterranean climates but are different in their urban emission sources and governing air quality regulations. The samples in Milan and Thessaloniki were mostly dominated by biomass burning activities whereas the particles collected in Los Angeles were primary impacted by traffic emissions. We analyzed the ambient PM2.5 mass concentration of Cadmium (Cd), Hexavalent Chromium (Cr(VI)), Nickel (Ni), Lead (Pb), as well as 13 PAH compounds in the PM samples, collected during both cold and warm periods at each location. The Pb exhibited the highest annual-average concentration in all 3 cities, followed by Ni, As, Cr(VI), Cd and PAHs, respectively. The cancer risk assessment based on outdoor pollutants was performed based on three different scenarios, with each scenario corresponding to a different level of infiltration of outdoor pollutants into the indoor environment. Thessaloniki exhibited rather high risk value associated with lifetime inhalation of As, Cr(VI) and PAHs. The highest cancer risk values were calculated in Milan where the lifetime risk of exposure to As, Cr(VI) and PAHs exceeded the US EPA standard across all scenarios by a considerable margin. The risk associated with Cr(VI) in Milan, which was the most significant among the investigated elements, ranged from (6.08±0.36)×10-6 to (9.82±0.58) ×10-6. In contrast, the estimated risks associated with metal and PAHs in Los Angeles were mostly comparable to the guideline value, even when the infiltration factor was assumed to be at peak. This observation highlights the impact of local air quality measures in improving the air quality and lowering the cancer risks in Los Angeles compared to the other two cities.

In recent years, due to the low energy utilization of the whole life-cycle of buildings and the di-minished indoor and outdoor comfort of buildings and the impact on the surrounding environ-ment caused by the carbon emissions of the building life-cycle, the establishment of a whole life- cycle carbon emission model for buildings to improve their energy utilization at all stages of their life-cycle has received unprecedented attention. In China, the construction industry has become a major carbon emitter, and traditional houses, as a green development building type, are an effec-tive way to achieve carbon neutrality in buildings, but the existing green building evaluation system lacks quantitative indicators of carbon emissions in the building life-cycle. The exclusive evaluation indexes for regional and characteristic buildings, such as traditional houses, are ne-glected; This study explored the formula for calculating the life-cycle carbon emissions model of traditional residential houses under a carbon emission intervention and used real measurements of the physical environment and comparative analysis of the limitations of existing local stand-ards; The results showed that the carbon emission calculation formulas for each stage of the life-cycle of traditional residential houses must be established by combining the selection of local building materials, and the materials for sustainable energy and carbon sinks of green systems. Based on the results of indoor and outdoor heat and humidity environmental tests of residential houses and an analysis of the limitations of existing evaluation indexes due to locality, four im-portant factors affecting locality green buildings in terms of energy utilization, site ecology and landscape, land saving and material saving were extracted; on this basis, the whole life-cycle carbon emission model of traditional residential houses is constructed by combining the existing green building evaluation standards with the carbon emission indexes of the life-cycle of tradi-tional residential houses.

Due to the severe environmental impact of the CO2 emissions associated with the production of Ordinary Portland Cement (OPC) and the increasing demand for this commodity material, the development of alternative products has become a global concern. One alternative to OPC, or alitic-based clinkers, are amorphous-wollastonitic low calcium hydraulic binders (AWLCs). This new class of hydraulic binders, described in the literature for the first time in 2015, may significantly reduce the CO2 emissions associated with its production, resulting from its lower calcium content, but also from the fact that its production technology can be fully electrified. In this paper it is provided a state-of-the-art review, providing a comprehensive description on the latest research, summarizing both the physico-chemical and mechanical characteristics for this type of hydraulic binders, as well as possible routes for its production at an industrial scale.

The C/N ratio is an extremely important parameter in the composting process, which is directly responsible for the growth of microorganisms. A low C/N ratio contributes to higher emissions of greenhouse gases and odorous substances, such as ammonia (NH3), which is formed by nitrogen mineralization. Due to the highly toxic effects of ammonia, it is a particularly unwanted by-product that can disrupt the composting process because it poisons microorganisms and cause environmental issues. The activity of anammox bacteria, so far analyzed only in wastewater treatment processes, is a particularly efficient method of nitrogen removal, having an advantage over the conventional methods used previously. Our study proofs the presence of anammox bacteria during composting, what gives an opportunity to improve the process and reduce its impact on atmospheric pollution. Despite the aerobic nature of this process, the composted mass of waste presents conditions conducive to the development of these ammonia oxidizing bacteria, as well as other strains of microorganisms cooperating with them. This makes it possible to compost at a low C/N ratio; in addition, there is no need for additional energy supply through aeration, as the processes carried out by anammox bacteria do not require oxygen.

In Korea, rice is a major staple grain and is mainly cultivated using various agricultural machinery. Air pollutants emitted from agricultural machinery have their origins mainly from the exhaustion of internal combustion engines. In this study, emission characteristics of five main air pollutants by European Environment Agency's Tier 1 method for rice cultivation was analyzed. Diesel is a main fuel for agricultural machinery and gasoline is generally used only for rice transplanters as a fuel in Korea. Tractors consume 46% of total fuel consumption and 56% of diesel fuel consumption. Gasoline used for rice transplanters accounts for 17% of total fuel consumption each year. Tractors and rice transplanters are emitting 82% of all total pollutants. From 2011 to 2019, the total amount of air pollutant emissions was decrease by 15%. That accounted for the reduction of rice cultivation fields in those periods. Rice transplanting operation was in charge of 42% of total emissions. Then, harrowing, harvesting, tilling, leveling, and pest control operations generated 10%, 10%, 8%, 8% and 7% of total emissions, respectively. The contribution of each air pollutant held 54% of CO, 39% of NOx, 5% of NMVOC, and 2% of TSP from the total emission inventory. The three major regions emitting air pollutants from mechanized agricultural practices were Jeollanam-do, Chungcheongnam-do, and Jeollabuk-do, which consume 55% of total fuel usage in rice farming. The total amount of air pollutant emissions from rice cultivation practices in 2019 was calculated as 8,448 Mg in Korea.

Early education is critical for improving energy efficiency. The purpose of this study is to explore the feasibility of Interactive Cross-Border Classes to increase awareness of energy efficiency among middle school students. We designed and tested an Interactive Cross-Border class between Chilean and Peruvian 8th-grade classes. The classes were synchronously connected and all students answered open-ended questions on an online platform. Some of the questions were designed to check conceptual understanding while others asked for suggestions of how to develop their economies while keeping CO₂ air concentration at acceptable levels. In real-time, the teacher reviewed the students’ written answers and the concept maps that were automatically generated based on their responses. Students peer-reviewed their classmates’ suggestions. This is part of an Asia-Pacific Economic Cooperation (APEC) STEM Education project on Energy Efficiency using APEC databases. We found high levels of student engagement, where students discussed not only the cross-cutting nature of energy, but also its relation to socioeconomic development and CO₂ emissions, and the need to work together to improve energy efficiency. In conclusion, Interactive Cross-Border classes are a feasible educational alternative, with potential as a scalable public policy strategy for improving awareness of energy efficiency among the population.

In the present scenario of increased industrialization and transportation in the world leads to increased consumption of fossil fuels which in turns leads to depletion of fossil fuels at a faster rate. Fossil fuels combustion is the dominant source for greenhouse gases and global warming. In view of energy crisis raised in 1970’s and environmental concern, many researches are directed towards search of alternative fuels which can replace consumption of fossil fuels as well as reduce pollution. In developing countries like India which is agriculture land the best alternative fuels are biodiesel and ethanol as they are produced from renewable feedstocks like sugarcane, corn etc. and they are also less hazardous to environment because of lower emission property. Ethanol blends results in significant reduction of emissions of hydrocarbon (HC), carbon monoxide (CO) and particulates matter but increase in nitrogen oxides (NOx). The main purpose of ethanol addition is to reduce the viscosity of biodiesel blends. This paper represents significance of Compression Ratio(CR) on performance, combustion and emission of single cylinder four stroke CI diesel engine by using various compression ratios such as 17.5:1, 18.5:1 and 19.5:1. Experimental research has been conducted with four types of ethanol blends, namely E10, E20, E30 and E40. Ethanol-biodiesel mixture mixed with 2% emulsifier 1% diethyl carbonate and 1% ethyl acetate to maintain similarity and to avoid phase separation. Ethanol subjected to high compression ratio has been used to increase brake thermal efficiency (BTE). The compression ratio has been increased to improve the combustion and performance of the diesel engine.

Electric vehicles, being able to reduce pollutant and greenhouse gas emissions and shift the economy away from oil products, can play a major role in the transition towards low-carbon energy systems. However, the related increase in electricity demand inevitably affects the strategic planning of the overall energy system as well as the definition of the optimal power generation mix. With this respect, the impact of electric vehicles may vary significantly depending on the composition of both total primary energy supply and electricity generation. In this study, Italy and Germany are compared to highlight how a similarity in their renewable shares not necessarily leads to a CO₂ emissions reduction. Different energy scenarios are simulated with the help of EnergyPLAN software assuming a progressive increase in renewable energy sources capacity and electric vehicles penetration. Results show that, for the German case, the additional electricity required leads to a reduction in CO₂ emissions only if renewable capacity increases significantly, whereas the Italian energy system benefits from transport electrification even at low renewable capacity. Smart charging strategies are also found to foster renewable integration; however, power curtailments are still significant at high renewable capacity in the absence of large-scale energy storage systems.

We do this research to investigate the relationship between renewable energy, public health expenditure, logistics performance indices, and economic and environmental sustainability in the ASEAN member states, through the analysis of a panel data from 2007 to 2017. The study used secondary data, which is downloaded from the World Bank Website and employs SEM (Structural Equation Modelling) model for testing hypothesis. The results show that the usage of renewable energy in logistical operations would enhance the environmental and economic performance in terms of mitigating carbon emissions and greenhouse gas emissions. While, public health expenditure and environmental performance is negatively correlated, which confirms that greater environmental sustainability with lower carbon emissions and greenhouse gases will improve human health and economic growth. Moreover, greater public health expenditure and poor environmental performance has negative effect on economic growth, inefficiency and low productivity of labor slowdown to the economic activities. For another side, the usage of renewable energy and the adoption of green practices in international logistics will develop the environmental sustainability, establish better image of a country and attract foreign direct investment inflows, and also minimize carbon emissions and public health expenditure, spurring sustainable economic growth with better export opportunities in pro-environmental countries.

In the industrial production of olive oil, both solid wastes and those produced from their incineration are a serious environmental problem since only 20% w/w of the fruit becomes oil and the rest is waste, mainly orujo and alperujo. A key aspect to transform these wastes into an important source of energy such as pellets is to recognize the most appropriate time of the year for waste drying, with the objective of minimizing the environmental impact of the volatile compounds contained in the waste. In this work, the emissions produced during thermal-mechanical drying were studied along a period of six months of waste storage in which alperujo and orujo were stored in open containers under uncontrolled environmental conditions. The studied emissions were produced when both wastes were dried in a pilot rotary drying trommel at 450ºC to reduce their initial humidity of around 70-80% w/w to 10-15% w/w. Results indicated that when the storage time of the wastes in uncontrolled environments increases, the emission of odorant compounds during drying also increases as a consequence of the biological and chemical processes occurring in the containers during waste storage. The main odorant VOCs were quantified monthly for six months at the outlet of the drying trommel. It was determined that the drying of this type of waste can be carried out properly until the third month of storage. Afterwards, the concentration of most VOCs produced widely exceeded the odor thresholds of selected compounds.

Biochar application to soil has been proposed as a means for reducing soil greenhouse gas emissions and mitigating climate change. The effects, however, of interactions between biochar, moisture and temperature on soil CO₂ and N₂O emissions, remain poorly understood. Furthermore, the applicability of lab-scale observations to field conditions in diverse agroecosystems remains uncertain. Here we investigate the impact of a mixed wood gasification biochar on CO₂ and N₂O emissions from loess-derived soils using: (1) controlled laboratory incubations at three moisture (27, 31 and 35%) and three temperature (10, 20 and 30°C) levels, and (2) a field study with four cropping systems (continuous corn, switchgrass, low diversity grass mix, and high diversity grass-forb mix). Biochar reduced N₂O emissions under specific temperatures and moistures in the laboratory and in the continuous corn cropping system in the field. However, the effect of biochar on N₂O emissions was only significant in the field, and no effect on cumulative CO₂ emissions was observed. Cropping system also had a significant effect in the field study, with soils in grass and grass-forb cropping systems emitting more CO₂ and less N₂O than corn cropping systems. Observed biochar effects were consistent with previous studies showing that biochar amendments can reduce soil N₂O emissions under specific, but not all, conditions. The disparity in N₂O emission responses at the lab and field scales suggests that laboratory incubation experiments are not reliable for predicting the impact of biochar at the field scale.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

A comprehensive investigation was undertaken at Vytautas Magnus University Experimental Station, located at 54°52’50” N latitude and 23°49’41” E longitude on soil (Epieutric Endocalcaric Planosol – PLe-gln-w) since 1999, to understand the impacts of different agrotechnical measures on soil health and crop yield. Two primary factors were assessed. Factor A incorporated practices of straw removal versus straw chopping and spreading, while Factor B evaluated a spectrum of tillage techniques: conventional deep ploughing, shallow ploughing, ploughless tillage, single seedbed discing, and two no-tillage practices, one of which involved cover crops. Findings from this long-term study highlight the significant potential of specific farming systems in enhancing soil organic carbon. It has a positive effect on the release of CO2 emissions from the soil, thus promoting soil resilience and increasing plant productivity. These insights are paramount in devising sustainable agricultural strategies to counter the challenges of climate change on agroecosystems. This research showcases the profound effects of combining residue management and tillage practices, setting a novel standard for sustainable soil management of climatic uncertainties.

Soil, geochemical, microbiological and archaeological studies were conducted at eight settlements dating from the Paleolithic to Late Medieval and New Times near the Southern Trans-Urals mountains, Russia. The forest-steppe landscapes, rivers and abundance of mineral resources have attracted people to region since ancient times. Properties of cultural layer (CLs): close to neutral pH, well structured, absence of salinity, enrichment with exchangeable calcium and anthropogenic phosphorus (0.2–0.4%). The majority of CLs start from 3–25 cm and last up to 40–60 cm and contain 6–10% organic carbon (Corg), in a layer of 0–20 cm because modern processes are developing here, at Ishkulovo site (around 14th century) Corg decreases to 1.3%, because CL is below 80 cm and in the absence of fresh organic material it is mineralized. The content of microbial biomass of the 0–10 cm layer is 520–680 μg С/g of soil, microbes cause the emission of 0.2–1.0 μg C–CO2/g soil per h. The proximity of the studied sites to deposits of copper, chromium, zinc, manganese and Magnitogorsk Metallurgical and Uchaly processing plants creates geochemical anomalies of soils. Pollutants are also released into the CLs from bronze products, ore, ceramic fragments and raw materials from their manufacture. It leads to the concentration of pollutants of the 1st (arsenic, lead, zinc) and 2nd (cobalt, copper, nickel, chromium) hazard classes in the studied CLs, often in quantities higher than the clarke and less often – more than the allowable content for human health.

This study introduces a neural network-based approach to predict dust emission, specifically PM2.5 particles, during almond harvesting in California. Using a feedforward neural network (FNN), the research predicts PM2.5 emissions by analyzing key operational parameters of an advanced almond harvester. The model is trained on extensive field data from the almond pickup system, including variables like brush speed, angular velocity, and harvester forward speed. The results demonstrate a notable predictive accuracy of the FNN model, with a Mean Squared Error (MSE) of 0.02 and a Mean Absolute Error (MAE) of 0.01, indicating a high degree of precision in forecasting PM2.5 levels. The study also finds a strong correlation between certain operational parameters and PM2.5 emissions, highlighting specific areas for optimization in harvesting techniques. By integrating machine learning with agricultural practices, this research provides a significant tool for environmental management in almond production, offering a method to reduce harmful emissions while maintaining operational efficiency. This model presents a solution for the almond industry and sets a precedent for applying predictive analytics in sustainable agriculture.

This paper focuses on the impact that urban traffic has on the environment. The study characterizes the global effect of GHG emissions, including the ecologic evaluation and the characterization, normalization, and evaluation factor. The work makes a detailed survey of the different modes of driving and their influence on engine performance as one of the principal causes of gas emissions during the combustion process. The article analyzes six types of vehicles equipped with different engine configurations: diesel and gasoline, GLP and GNC, hybrid electric, and plug-in hybrid electric. Simulation of the driving mode under various operational conditions for every type of engine results in energy consumption, thus, in GHG emissions, carbon dioxide and monoxide, nitrogen oxides, and Sulphur dioxide. The study concludes that a reduction in vehicle speed, thus in the engine revolutions, has positive effects on engine combustion and gasses emissions, which is reduced by 27.5%. The study also concludes that the limitation in driving mode, avoiding sharp and sudden acceleration, may reduce up to 45% of GHG emissions. The changes applied in the driving mode improve the air quality in the urban environment, reducing the content of GHG from 39% to 61%.

The utilization of solar energy technology is crucial for generating hydrogen in sustainable energy systems. While traditional methods involving natural gas, coal, and oil have been employed for hydrogen production, this study aims to explore environmentally friendly techniques. Green hy-drogen, despite being a more expensive option compared to fossil fuel-derived hydrogen, has prompted engineers to develop affordable and low-carbon technologies. The microgrid model was developed to showcase a self-contained DC islanded system designed to supply power to an electrolyzer, capitalizing on both a solar array and an energy storage unit. This comprehensive model offers a versatile platform for evaluating the operational dynamics involved in the sustainable production of green hydrogen. Over a span of seven days, it permits the as-sessment of hydrogen generation characteristics through the utilization of solar energy, either di-rectly from a solar array or through an integrated system that incorporates energy storage. The model encompasses a multi-domain framework, encompassing electrical, thermal liquid, and thermal gas aspects, facilitating a holistic exploration of the intricate processes underlying the green hydrogen production system. Through this simulation, the feasibility and efficiency of harnessing renewable energy sources for hydrogen production in an off-grid setting can be comprehensively examined and optimized, contributing to the advancement of sustainable energy solutions.

This article presents an experimental study focused on the impact of supplementing pure gasoline (E0) with bioethanol, gradually increasing the biofuel concentration up to 70% (E10, E50, and E70). The research was conducted in two phases: In the first phase (Part I), the engine's operation involved varying engine speeds (n = 2000 rpm, n = 2500 rpm) and adjusting throttle openings (15%, 20%, 25%) to analyze changes in brake torque, thermal efficiency, and ecological indicators. The second phase (Part II) aimed to complement and clarify the study data. Here, the engine was maintained at a constant speed (n = 2000 rpm) and brake torque (MB = 80 Nm) while altering ignition timing. The findings revealed that increasing the bioethanol concentration up to 70% led to modest enhancements in engine brake torque and thermal efficiency. However, the most significant impact was observed in the reduction of greenhouse gas emissions and incomplete combustion byproducts. The study also established that achieving higher thermal efficiency requires compensating for the extended ignition delay phase resulting from bioethanol addition by advancing ignition timing. Nevertheless, this approach is constrained by the escalating emissions of carbon dioxide and hydrocarbons. These findings provide valuable insights into optimizing the balance between bioethanol supplementation, engine performance, and environmental sustainability in spark ignition engines.

Organic horticulture is a holistic management system which follows good production practices and should be considered as the cornerstone of mitigating climate change and to produce healthier fruits and vegetables. This agroecosystem practice not only benefits the green economy but promotes and enhances soil biological activity, biodiversity, and other biological cycles in the sphere. The last decade has observed a rise in the production and consumption of organically certified agricultural products due to their higher nutritional value, lowered risk of exposure to harmful chemicals and improved organoleptic properties. The aim of this review was to demonstrate the considerable impact of organic horticulture on mitigating climate change and simultaneously satisfy consumer needs. The outcome of this review demonstrates that there are still numerous research studies required to evaluate how different farming systems and pedoclimatic conditions can contribute to more efficient horticultural practices.

Nitrogen (N) is the most limiting nutrient for the production of vegetable crops, but anthropogenic sources pose risks due to its transformation into several reactive forms and movement throughout the environment. To mitigate the impact of environmental losses, current research efforts aim to improve management practices to obtain a greater Nutrient Use Efficiency (NUE). From a chemical, biological, and ecophysiological perspective, at a reductionist level we have acquired a considerable mechanistic understanding about the N cycle, the varied N chemical forms, microbial interactions and physiology of crop uptake. However, at a holistic level, we are far from obtaining an adequate understanding of the myriad of multi-level cropping system, genetic, socioeconomic, environmental, and ecological interactions that have an effect on the N cycle and NUE. Here, based on a selected review of the literature, we provide a perspective on the potentials to increase the NUE of vegetable crops, by adopting a range of best management practices and by highlighting some of the N x system interactions that may be considered to better understand the complex dynamics of the N cycle, to optimize the NUE of vegetable crops, and to explore alternatives to the reliance on the use of synthetic N sources.

Over 130 countries have committed to reaching net-zero CO2 or GHG emissions by 2050, yet this ambition is rarely underpinned by robust policies. By applying a detailed integrated assessment modelling approach for Brazil, we assess, for the first time, the extent to which the existing and planned local policies could put Brazil on the path to its net zero pledge. This includes quantifying the role of nature-based solutions, such as protection and restoration, and engineered solutions, such as bioenergy with carbon capture and storage (BECCS). We show protection is the single most important climate mitigation measure at relatively low costs, whereas relying heavily on engineered solutions would jeopardise Brazil’s chances of achieving its net zero pledge. We also show that the mismatch between Brazil's short- and long-term climate targets reflects current weak environmental governance. Our analysis reinforces the urgent need for Brazil to eliminate illegal deforestation and go beyond to help fight climate change whilst curbing biodiversity loss.

We present a method to turn results of model-based optimisations into resilient and comprehensible control strategies. Our approach is to define priority lists for all available technologies in a district energy system. Using linear discriminant analysis and the results of the optimisations, these are then assigned to discrete time steps using a set of possible steering parameters. In contrast to the model-based optimisations, the deduced control strategies do not need perfect foresight but solely rely on data about the present. Our result indicate that the results of the control strategies obtained using the proposed method are comparable to the results of the linear optimisations, in our case in terms of emissions and prices.

In the U.S. 44% of low-income households struggle to pay their utility bills, affecting their ability to afford necessities such as food and health expenses. Several government and utility funded energy efficiency programs exist to assist those experiencing energy insecurity. In Salt Lake City, Utah, there is a high demand for, but low availability of, energy efficiency services in underserved neighborhoods creating an opportunity for creative community-based programs to fill this inherent gap. This pilot project, involving the exchanging of LED bulbs in Salt Lake City, highlights the development of a community-based energy efficiency program that aims to bring energy savings to a uniquely targeted portion of the city and determines its feasibility in addressing energy insecurity at a larger scale. Through the 8-month project duration, 1,432 bulbs were exchanged at 23 events reaching 181 households in low-income areas. Through a year of use, these bulbs are estimated to save residents approximately 18,219 USD in electricity bills and reduce CO2 emissions from power plants by 122.23 metric tons, in addition to a savings of 4,400 USD in social cost of carbon as defined by the U.S. Environmental Protection Agency. Since this pilot reached less than 1% of households, we extrapolated a reach of 2%, 5%, and 7.5% and found substantial potential decreases in power plant emissions and financial savings. As this project is ongoing and being expanded, we discuss relevant findings that will help shape future community-based models so that they are appropriately deployed and more effective in alleviating local energy insecurity.

This panel study investigates the relationship between green logistics indices, economic, environmental, and social factors in the perspective of Asian emerging economies. This study adopted FMOLS and DOLS methods to test research hypothesis, catering the problem of endogenity and serial correlation. The results suggest that logistics operations, particularly LPI2 (efficiency of customs clearance processes), LPI4 (quality of logistics services) and LPI5 (trade and transport-related infrastructure), are positively and significantly correlated with per capita income, manufacturing value added and trade openness. While, greater logistics operations are negatively associated with social and environmental problems including, climate change, global warming, carbon emissions, and poisoning atmosphere. In addition, human health is badly affected by heavy smog, acid rainfall, and water pollution. The findings further extend and reveal that political instability, natural disaster and terrorism are also a primary cause of poor economic growth and environmental sustainability with poor trade and logistics infrastructure. Further, the application of renewable energy resources and green practices can mitigate negative effects on social and environmental sustainability without compromising the performance of economic growth. There is very limited empirical work presented in literature using renewable energy and green ideology to solve macro-level social and environmental problems, while this study will assist the policymakers and researchers to understand the importance of green concept in improving countries’ social, economic and environmental performance.

The UK Government is committed to reducing greenhouse gas (GHG) emissions by 80% by 2050. Buildings are responsible for 37% of the total GHG emissions in the UK and the need to reduce their emissions has resulted in more stringent building regulations in the recent past. The regulations, energy rating systems and voluntary guidelines — all are primarily aimed at reducing the need for heating and associated energy use by increasing insulation and air-tightness. However, future climates are projected to be warmer than the present day. Internal gains dominated non-domestic buildings will likely overheat, the adaptation to which will require energy-intensive cooling solutions, thus defeating the purpose of heating-focused regulations. This research investigated the effects of warming climate on overheating, and energy use and resulting emissions in representative urban office spaces in London in the present-day and future climates using hourly dynamic thermal simulations. Findings suggest that more airtight and highly—insulated office buildings designed for heating—dominated temperate UK climate will overheat in the 2050s. Heating demand reduces but electricity consumption increases by 121% when hybrid cooling is adopted to ameliorate overheating. Despite the rise, adopting a mixed-mode ventilation strategy was one of the ways of achieving overall energy efficiency while meeting benchmark overheating and carbon emissions target in present and future climatic contradictions. Current heating-focused legislations need to be urgently re-evaluated to account for the effects of climatic variability and overheating risks.

As the world attempts to decarbonise the food industry and limit greenhouse gas (GHG) emissions, plant-based meat analogues (PBMAs) have emerged as a sustainable alternative to traditional meat. This study implemented a life cycle assessment (LCA) to rigorously compare the environmental impacts of a beef burger (BB), produced with British beef, against a meat analogue (MA) equivalent with a publicly available recipe. For the LCA, a cradle-to-fork system boundary was utilised, alongside a functional unit of a single 100 g burger patty. Results from the LCA revealed that the BB patty had more than double the total environmental impact than the MA equivalent, as well as possessing a global warming impact that was 62% higher. A simple extrapolation illustrated that if the UK population switched from beef to meat analogue patties, 3 million tonnes of CO2e could be saved annually, corresponding to 0.74% of the country’s yearly territorial GHG emissions. Scenario analyses displayed how the environmental impact of the MA patty remained stable regardless of changes in exportation, ingredient origin or soy protein sourcing. Moreover, sensitivity analysis conducted with an alternative characterisation method corroborated initial findings, whilst uncertainty analysis ensured that nearly all conclusions generated from the original comparison were robust. Future studies should conduct peer-reviewed LCAs on PBMA patties with commercial recipes based on other plant-based proteins, as well as fully understanding any potential health implications of long-term PBMA consumption.

In drilling small holes with diameters of 1 mm or less, minute clogging and twining of chips or adhesion of the workpiece material can become factors in causing breakages of the drill bit; moreover, it can be difficult to identify the machining state. Acoustic emission (AE) sensing is a nondestructive inspection technique that measures the elastic-stress waves that are generated when a material is deformed and fractured. AE sensing permits highly sensitive measurements to be made without changing the rigidity of the experimental system, unlike force sensing of cutting resistance, etc. In the present study, attempts were made to identify the machining state and tool wear, and to predict abnormalities in small-diameter drilling by using the change in the frequency of AE signal waveforms arising from deformation and fracture. It was shown that it is possible to predict the breakage of the drill bit by detecting the high-frequency AE signals caused by adhesion. In addition, a correlation map of the AE frequency spectrum for identifying the machining state in a drilling operation is suggested.

The new energy structure needs to balance energy security and dual carbon goals, which has brought major challenges to coal-fired power plants, the pollution reduction and carbon emissions reduction of coal-fired power plants will be a key task in the future. This article proposes an optimization operation of electrostatic precipitators(ESP), based on the working mechanism and historical data of ESP, voltage-current characteristic model and outlet dust concentration prediction model are constructed by deep learning algorithm, Particle Swarm Optimization(PSO) is used to achieve the optimal energy consumption while ensuring stable outlet dust concentration. By training with historical data collected on site, accurate prediction of secondary current and outlet dust concentration of ESP has been achieved, the Mean Absolute Percentage Error(MAPE) of secondary current is less than 1.5%, and the MAPE of outlet dust concentration of ESP on the test set is less than 5.2%. Finally, the optimization experiment is carried out in a 330MW coal-fired power plants, the results showed that the fluctuation of the outlet dust concentration is more stable, and the energy saving is about 43% after optimization, according to the annual operation of 300 days, the annual average carbon reduction is approximately 2621.34 tons. This method is effective and can be applied widely.

This study investigates the influence of economic growth on CO2 emissions levels in three developed countries—Argentina, Equatorial Guinea, and South Korea—based on their status as high-income countries. We test the environmental Kuznets curve (EKC) hypothesis using the time series approaches to check the relationship and direction of causality among the variables over a sample spanning 1974–2020. The results show an inverted U-shaped short-run relationship in all three countries. In the long run, only South Korea supports the EKC hypothesis. Further, Granger causality results indicate the existence of causality. These long-run causal relationships between economic growth and emissions recommend one policy implication that wealthy governments must expand investments in renewable clean energy projects and R&D, with regulatory measures to suppress harmful environmental procedures and support environmentally friendly development.

Soil moisture reserve is a key factor in maintaining soil fertility and all other related ecosystem services (including carbon sequestration, soil biodiversity, soil erosion control). In semiarid blown-sand areas under aridification water preservation is a particularly crucial task for agriculture. The international Diverfarming project (2017–2022) within the EU Horizon 2020 Program focused on the impacts of crop diversification and low-input practices in all pedoclimatic regions of Europe. In the three-year experiment conducted in the Pannonian region the impacts of intercropping asparagus with different herbs on some provisioning and regulating ecosystem services were evaluated in the Kiskunság sand regions. Relying on the findings based on a range of measured physical and chemical soil parameters and on crop yields and qualitative properties, advice was formulated for farmers. The message drawn from the experiment is somewhat ambiguous. The local farmer agrees that crop diversification improves soil quality, but he denies that it would directly influence farm competitiveness, which primarily depends on cultivation costs (such as fertilization, plant protection and labour). Further analyses are needed to prove the long-term benefits of diversification through enriching soil microbial life and the possible reduction of fertilizer use while water demand is kept at a low level and the same crop quality is ensured.

To date, only a few studies focused on carbon monoxide (CO) production during waste composting; all targeted on CO inside piles. Here, the CO net emissions from compost piles and the assessment of worker’s occupational risk of exposure to CO at large-scale composting plants are shown for the first time. CO net emissions were measured at two plants processing green waste, sewage sludge, or undersize fraction of municipal solid waste. Effects of the location of piles (hermetised hall vs. open yard) and turning (before vs. after) were studied. Higher CO net emission rates were observed from piles located in a closed hall. The average CO flux before turning was 23.25 and 0.60 mg‧m-2‧h-1 for hermetised and open piles, respectively, while after – 69.38 and 5.11 mg‧m-2‧h-1. The maximum CO net emissions occurred after the compost was turned (1.7x to 13.7x higher than before turning). The top sections of hermetised piles had greater CO emissions compared to sides. Additionally, 5% of measurement points of hermetised piles switched to ‘CO sinks’. The 1-h concentration in hermetised composting hall can reach max. ~50 mg CO∙m-3 before turning, and >115 mg CO∙m-3 after, exceeding the WHO thresholds for a 1-h and 15-min exposures, respectively.

Large ruminant production is associated with high greenhouse gas emissions (GHGe) intensity, with the highest in southeast Asia being Laos at 102.9 CO2eq/kg meat produced, compared with average global meat emissions intensity of 33 CO2eq/kg. As recent studies in Laos identified emissions control molasses blocks (ECBs) achieved abatement of 470kg CO2eq/20kg block consumed, a study was conducted with a supplement mix with reported methane reducing properties, containing plant tannins and citral extract, salt, molasses and water. Groups of housed dairy buffalo (n=7) and pasture-fed grazing beef cows (n=11) were randomly selected, body condition scores estimated (BCS:1-5) and baseline nasa-oral methane eructation measured daily for 2 weeks. All animals were offered 300-400g/day of the mix for a month, with buffalo accessing abundant fresh cut forages whereas the grazing cows accessing rice straw and pasture declining in quality and quantity due to severe drought. The buffalo consumed all of the mix and retained their BCS of 3, whereas the cattle consumed between 200-300g/day of the mix and their BCS declined from 1.5 to 1.0 during the trial. Analysis of data points (buffalo n=309; cattle n=378) found average methane concentration (AMP) per animal of both cohorts increased over the 2 week baseline period, then declined during the supplementation period by 36% in the buffalo and 18% in cattle cohorts.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

Responding to an urgent call for effective and cost-efficient enforcement of emission regulations from ocean-going vessels (OGVs) at sea, the Royal Belgian Institute of Natural Sciences, one of the 17 official partners of the Belgian coastguard structure, launched its airborne sniffer program in 2015. A custom-built sniffer sensor was installed on board of the Belgian coastguard aircraft and has been used for the in-situ measurement of SO2 and NOx in OGV exhausts, providing non-compliance alerts to port inspection authorities in Belgium and other EU member states. To guarantee the consistency in quality and reliability of the airborne non-compliance alerts, the standard operational procedures and measurement methodology have been described and recorded in a sniffer quality management system (SQMS). As part of the SQMS, alerting thresholds for non-compliance with SO2 and NOx standards were defined based on the emission limits and the measurement uncertainty. In addition, compliant measurements for the fuel sulfur content (FSC) were shared through Thetis-EU, which is the sulfur inspection database hosted by the European Maritime Safety Agency (EMSA). By providing both non-compliance alerts and compliant measurements to port inspection authorities, the coastguard aircraft fulfills a first-step in the enforcement chain. This article demonstrates that the reported alerts have not only led to several sanctions, but the analysis also showed that the provision of airborne alerts improved the efficiency of the port inspection authorities drastically, resulting in a cost-efficient improvement of their enforcement strategy. Port inspection authorities were able to follow-up on 46% of the generated FSC alerts. In addition, 43% of the alerted OGVs, which were followed up, were confirmed as non-compliant after a port inspection. Accordingly, conditions were in place to effectively sanction 20% of the non-compliant observations. For NOx alerts, a limited follow-up was done by port inspection authorities and none of the alerts were confirmed by those inspections, which is mainly due to the lack of suitable inspection mechanisms and the absence of additional EU implementation regulations on NOx emission inspections. Aiming at paving the way for a stricter enforcement of airborne non-compliance alerts, a validation analysis was done between the airborne FSC measurements and reference FSC measurements. In addition to onboard measurements from exhaust gas cleaning systems (EGCS), analyzes of fuel samples were also carried out by port inspection authorities in order to acquire reference measurements. The validation analysis presented in this study showed that the empiric deviation of the airborne FSC measurements with the reference measurements was significantly lower than the uncertainty used in the reporting thresholds. It has also been shown that aerial measurements provide evidence-based data that, given an appropriate confidence interval, has the potential to be considered reliable legal evidence.

CO₂ emissions have been identified as the main driver for climate change, with devastating consequences for the global natural environment. The steel industry is responsible for ca. 8%-11% of global CO₂ emissions, due to high fossil-fuel and energy consumption. The onus is therefore on industry to remedy the environmental damage caused and to decarbonise production. This desk research report follows a two-tiered route: 1) exploring the Bio Steel Cycle; 2) proposing a seven-step strategy to overcome the challenges within the iron and steel industry. The true levels of CO₂ emissions in the steelmaking process, during the blast-furnace/basic-oxygen-furnace operation, will be detailed first, at 4.61t of CO₂ emissions/t of steel produced. The manuscript proposes a solution for reduced carbon emissions steelmaking with the Bio Steel Cycle components and detail on how to reach net-zero carbon emissions steel production. The 7-step-implementation-strategy as a potential solution to achieve net and true zero carbon emissions steel production in the short to medium-term. The findings of this are pointing towards the conclusion that CO₂ emissions seem to have been under-reported and under-estimated in the past, but the emission can be addressed if the correct scenarios for net-zero steel manufacturing are implemented by 2050.

The risk of inhalation exposure to elevated concentrations of hydrogen sulfide (H₂S) and ammonia (NH₃) during the agitation of stored swine manure is high. Once or twice a year, farmers agitate manure before pump-out and application to fields. Agitation of the swine manure causes the short-term releases of highly toxic levels of H₂S and NH₃. In our previous pilot-scale studies, the biochar powder had shown significant mitigation of H₂S and NH₃ emissions when surficially applied to manure immediately before agitation. However, fine biochar powder application poses hazards by itself and may not be practical to apply on a farm scale, especially when livestock and workers are present. We hypothesized that applying pelletized biochar to manure surface is just as effective as applying powder to protect farmers and animals from excessive exposure to H₂S and NH₃. This work reports on the lab-scale proof-of-the-concept trials with biochar pellets on the lab-scale. The objective was to compare the biochar pellets and biochar powder on their effectiveness of mitigation on H₂S and NH₃ gases during 3-hour long swine manure agitation. Three scenarios were compared in (n=3) trials (i) control, (ii) 12.5 mm thick surficial application to manure surface of biochar powder, and (iii) an equivalent (by mass) dose of pelletized biochar applied to manure surface. The biochar powder was bound with 35% (wt) water into ~5 × 10 mm (dia × length) pellets. Biochar powder was significantly (p<0.05) more effective than the biochar pellets. Still, pellets reduced total H₂S and NH₃ emissions by ~72% and ~68%, respectively (p=0.001), compared with ~99% by powder (p=0.001). The maximum H₂S & NH₃ concentrations were reduced from 48.1±4.8 ppm & 1,810±850 ppm to 20.8±2.95 ppm & 775±182 ppm by pellets, and to 22.1±16.9 ppm & 40.3±57 ppm by powder, respectively. These reductions are equivalent to reducing the maximum concentrations of H₂S and NH₃ during the 3-h manure agitation by 57% and 57% (pellets) and 54% and 98% (powder), respectively. Treated manure properties hinted at improved nitrogen retention, yet not significant due to high variability. We recommend scaling-up and trials on the farm-scales using biochar pellets to assess the feasibility of application to large manure surfaces and techno-economic evaluation.

This study aligns with the 2030 United Nations Sustainable Development Goals- 3 which aim to “ensure healthy lives and promote well-being for all at all ages”. It contributes to the nascent literature stream on energy-health dynamics by introducing a holistic theoretical model to empirically examine the mediation effect of carbon emissions on the relationship between nonrenewable energy and infant mortality rates. Using an unbalanced panel data on 42 Asia and the Pacific countries from 2005 to 2015 and deploying the structural equation modeling approach, the empirical results are surmised as follows: (i) in regard to the full sample of countries, nonrenewable energy indirectly increases infant mortality rates through increasing carbon emissions. In other words, carbon emissions play a partial mediation role between nonrenewable energy and infant mortality rates; and (ii) for the different income groups, carbon emissions show varying mediation effects. For example, the mediation effects of carbon emissions in lower-middle and upper-middle income countries are found to be similar to those of the full sample of countries. Therefore, based on these findings, we conclude that nonrenewable energy is an essential determinant of infant mortality rates. Policy recommendations are put forward.

The main source of electricity worldwide stems from fossil fuels, contributing to air pollution, global warming, and associated adverse effects. This study explores wind energy as a potential alternative. Nevertheless, the variable nature of wind introduces uncertainty in its reliability. Thus, it is necessary to identify an appropriate machine learning model capable of reliably forecasting wind speed under various environmental conditions. This research compares the effectiveness of artificial neural networks (ANN) and convolutional neural networks (CNN) in predicting wind speed across three locations in South Africa, characterised by different weather patterns. Empirical results show that CNN outperforms ANN in accurately forecasting wind speed under different weather conditions. This superiority is likely due to the inherent architectural attributes of CNNs, including feature extraction capabilities, spatial hierarchy learning, and resilience to spatial variability. These results could be useful to decision-makers in the energy sector.

Non-exhaust road transport emissions in cities contribute to poor air quality and create health impacts. This paper presents a new study of the emitted particles due to the tyres-road wear ‘TRWP’ in real driving and gives their emission factors EF. The most frequently observed particles were &lt;1 µm; followed by particles size between [1µm, 4µm] for urban, suburban and highway areas. These particle sizes are well-known to have a higher degree of toxicity. An overall analysis of all the measured pollutants gave EF equal to 30 10+12 #/km and 35 10+12 #/km, respectively for urban and sub-urban areas; and 5 10+12 #/km on highway. The analysis of the 19 most emitted pollutants, taken individually, showed that their EFs ranged from 0.003 to 18.142 10+12#/km. The obtained EF are above the value of the Euro standard for vehicles, but are below the values for vehicles unequipped with a particle filter. Significant test analysis confirmed that inertia of chemical pollutants is homogeneous. EF assessment of the PM10 and PM2.5 emitted is equal to 1.45 mg/km and 0.35 mg/km respectively. These results should contribute to the emergence of future regulations of non-exhaust emissions and should help to analyse the exposure-impact relationship to TRWP.

In recent years, the Canadian dairy sector has faced escalating challenges due to its significant contribution to greenhouse gas emissions, particularly methane. This paper critically examines a spectrum of innovative techniques aimed at mitigating methane emissions within this sector, scrutinizing their cost-effectiveness, efficiency, compatibility with animal welfare standards, and adherence to both existing and prospective Canadian environmental legislations. The discourse commences with an exhaustive overview of contemporary methane reduction methodologies pertinent to dairy farming, followed by a rigorous analysis of their economic feasibility. This includes a detailed cost-benefit analysis, juxtaposed with the efficiency and technological advancements these techniques embody. A pivotal aspect of this examination is the alignment of animal welfare with emission reduction objectives, ensuring that strategies employed do not compromise the health and well-being of dairy cattle. Furthermore, the paper delves into the legislative landscape of Canada, evaluating the congruence of these techniques with current environmental laws and anticipating future regulatory shifts. Performance indicators for emission reduction are critically assessed, establishing benchmarks tailored to the Canadian context. This is complemented by an exploration of the market potential of these innovations, including factors influencing their adoption and scalability in the market. The analysis culminates with a synthesis of case studies and best practices within Canada, offering insights into successful implementations and drawing lessons for future endeavors. This comprehensive approach serves not only to address the immediate environmental and health impacts associated with dairy farming emissions but also contributes significantly to the overarching goal of sustainable development in the agricultural sector.

This paper presents a new implementation of a 2-box absolute flow model, enabling the calculation of CO₂ transfer between the atmosphere and a mixing reservoir representing the combined effect of the terrestrial and ocean regions. The model uses published values of anthropogenic CO₂ fossil fuel emissions (CO2ff), atmospheric CO₂ mixing ratio and nuclear weapons bomb yields, to compute atmospheric d¹³C and Δ¹⁴C time-series. The level of agreement between the calculated values and the accepted values for d¹³C is within ± 0.05 ‰, and for Δ¹⁴C is within ± 3‰, spanning 200 years. The model contains only seven internal parameters; these are varied to optimize the fit, leading to reasonable parameter values, indicating the validity of the method. In addition, the model shows how a rising CO₂ exchange influx fluctuating with surface temperature is compatible with a nett atmospheric CO₂ sink. The study demonstrates that a single CO₂ residence time applies to both the ¹⁴C bomb pulse and the anthropogenic flux, contrary to the conventional view that "bomb radiocarbon and anthropogenic CO₂ do not behave identically." [Joos 1994 Nature 370, 181–182]. It is shown that the difference in behaviour, claimed to be due to seawater chemistry, is not significant in practice since fluctuating bulk carbon dominates fluctuating isotopic ratio. A new analysis of the airborne fraction indicates that the assumption of a time-dependent exchange influx results in a similar residence time for bulk CO₂ as for ¹⁴C in the nuclear bomb pulse, reinforcing the view that the ¹²C, ¹³C and ¹⁴C carbon isotopic forms of CO₂ behave similarly in the carbon cycle.

In this work, we investigate the ability of a data assimilation technique and space-borne observations to quantify and monitor changes in nitrogen oxides (NOx) emissions over North-Western Greece for the summers of 2018 and 2019. In this region, four lignite-burning power plants are located. The data assimilation technique, based on the Ensemble Kalman Filter method, is employed to combine space-borne atmospheric observations from the high spatial resolution Sentinel-5 Precursor (S5P) Tropospheric Monitoring Instrument (TROPOMI) and simulations using the LOTOS-EUROS Chemical Transport model. The Copernicus Atmosphere Monitoring Service-Regional European emissions (CAMS-REG, version 4.2) inventory based on year 2015 is used as the a priori in the simulations. Surface measurements of nitrogen dioxide (NO2) from air quality stations operating in the region are compared with the model surface NO2 output using either the a priori (base run) or the a posteriori (assimilated run) NOx emissions. The high biases found between the in situ NO2 measurements and the base run surface NO2 decrease in the assimilated run in most cases. The bias in the station near the largest power plant decreases to 2.0 μg/m3 (2.83 μg/m3) from 10.5 μg/m3 (8.46 μg/m3) in 2019 (2018 respectively). Concerning the estimated annual a posteriori NOx emissions it was found that, for the pixels hosting the two largest power plants, the assimilated run results in emissions decreased by ~40-50% for 2018 compared to 2015, whereas a larger decrease, of ~70% for both power plants, was found for 2019, after assimilating the space-born observations. For the same power plants, the European Pollutant Release and Transfer Register (E-PRTR) reports decreased emissions in 2018 and 2019 compared to 2015 (-35% and -38% in 2018, -62% and -72% in 2019), in good agreement with the estimated emissions. We further compare the a posteriori emissions to the reported energy production of the power plants during the summer of 2018 and 2019. Mean decreases of about -35% and-63% in NOx emissions are estimated for the two larger power plants in summer of 2018 and 2019, respectively, which are supported by similar decreases in the reported energy production of the power plants (~-30% and -70%, respectively).

The World Health Organization’s Health Economic Assessment Tool (HEAT) for walking and cycling is a user-friendly web-based tool to assess health impacts of active travel. HEAT, developed over 10 years ago, has been used by researchers, planners and policymakers alike in appraisals of walking and cycling policies of both national and more local scales. HEAT has undergone regular upgrades adopting the latest scientific evidence. This article presents the most recent upgrades of the tool. Health impacts of walking and/or cycling in a specified population are quantified in terms of premature deaths avoided (or caused). In addition to the calculation of benefits from physical activity, HEAT was recently expanded to include assessments of the burden associated with air pollution exposure and crash risks while walking or cycling. Further, impacts on carbon emissions from mode shift to active travel modes can now be assessed. Monetization of impacts using Value of Statistical Life and Social Costs of Carbon now uses country-specific values. As active travel inherently results in often substantial health benefits as well as not always negligible risks, assessments of active travel behaviour or policies are incomplete without considering health implications. The recent developments of HEAT make it easier than ever to obtain ballpark estimates of health impacts and carbon emissions related to walking and cycling.

Mangrove forests store and sequester large area-specific quantities of blue carbon (C_org). Except for tundra and peatlands, mangroves store more C_org per unit area than any other ecosystem. Mean mangrove C_org stock is 738.9 Mg C_org ha⁻¹ and mean global stock is 6.17 Pg C_org, which equates to only 0.4–7% of terrestrial ecosystem C_org stocks but 17% of total tropical marine C_org stocks. Seagrasses sequester more C_org per unit area than mangroves (179.6 g C_org m⁻²·a⁻¹) but twice the C_org sequestered by mangroves globally (15 Tg C_org a⁻¹). Mangroves sequester only 4% (range 1.3–8%) of C_org sequestered by terrestrial ecosystems, indicating that mangroves are a minor contributor to global C storage and sequestration. CO₂ emissions from mangrove losses equate to 0.036 Pg CO₂-equivalents a⁻¹ based on rates of C sequestration but 0.088 Pg CO₂-equivalents a⁻¹ based on complete destruction for conversion to aquaculture and agriculture. Mangrove CO₂ emissions account for only 0.2% of total global CO₂ emissions but 18% of CO₂ emissions from the tropical coastal ocean. Despite significant data limitations, the role of mangrove ecosystems in climate change mitigation is globally insignificant but may be more significant and effective at the national and regional scale.

Education is one of the most important tools available to policymakers and non-governmental bodies to promote a change in the behavior of society and to address the climate crisis, in line with the 4^th and 13^th Sustainable Development Goals of the United Nations 2030 Agenda. Project-based learning (PBL) addresses real and global challenges and allows the academic and professional formation of students. As part of the reflection stage of the educational action research method using the Business Canvas Model (BMC), pedagogic deficiencies were identified in the PBL and a didactic proposal was elaborated to emulate the interaction of students with the ecosystems of society. A prototype for improving the management of organic manures as soil amendments was initially developed, to provide the students with a quick start on the first steps of the proposed project. In the 10 sessions designed for the PBL (Make it happen!), the students elaborate a more sophisticated artifact in response to the demands of potential clients, as per the outcomes of the primary market research (5^th session). Active teaching methods and tools, such as a modified template of the BMC with the Rumsfeld’s matrix, aid the metacognition of students and their competences development. In a double session of the PBL, the primary market research is organized with key stakeholders of the agroindustry to enquire about the feasibility of the implementation of the technological solution and the logistics at farm level. Finally, the evaluation relies on the suitability of the upgraded prototype to respond customers’ demands.

The presence of the quantum Rayleigh scattering, or spontaneous emission, inside a dielectric medium such as a beam splitter or an interferometric filter, prevents a single-photon from propagating in a straight-line. Modelling a beam splitter by means of a unitary transformation is physically meaningless because of the loss of photons. Additional missing elements from the conventional theory are: 1) the quantum Rayleigh stimulated emission which can form groups of photons of the same frequencies, and 2) the unavoidable parametric amplification of single-photons in the original parametric crystal. An interference filter disturbs, through multiple internal reflections, the original stream of single-photons, thereby confirming the existence of groups of photons being spread out to lengthen the coherence time. The approach of modelling individual, single measurements with statistical ensemble probability amplitudes leads to the counterintuitive explanations of the experimental outcomes and should be replaced with pure states describing instantaneous measurements which are afterwards averaged.

The motivations for the move to electrified vehicles are discussed with reference to their improved energy efficiency, their potential for lower CO2 emissions (if the electricity system is decarbonized), their lower (or zero) NOx/particulate matter (PM) tailpipe emissions, and the lower overall costs for owners. Some of the assumptions made in life-cycle CO2 emissions calculations are discussed and the effect of these assumptions on the CO2 benefits of electric vehicles are made clear. A number of new tribological challenges have emerged, particularly for hybrid vehicles that have both a conventional internal combustion engine and a battery, such as the need to protect against the much greater number of stop-starts that the engine will have during its lifetime. In addition, new lubricants are required for electric vehicle transmissions systems. Although full battery electric vehicles (BEVs) will not require engine oils (as there is no engine) they will require a system to cool the batteries – alternative cooling systems are discussed, and where these are fluid based, the specific fluid requirements are outlined.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

(1) Background: Human-generated greenhouse gas (GHG) emissions are the largest contributor to climate change worldwide. Climate change negatively impacts human and planetary health threatening the existence of life on earth. The healthcare industry is responsible for approximately 8.5% of carbon emissions in the United States. Measuring baseline GHG emissions is the first step in emissions reduction. However, very few models of measurement exist for health care organizations. This project aimed to develop and implement a program to measure and track GHG emissions at a Midwestern Academic Medical Center (MAMC) and to educate staff to manage the process. (2) Methods: A Plan, Do, Study, Act (PDSA) cycle and Quality Improvement methodology was used to develop, implement, and assess a standardized GHG emission inventory process to measure Scope 1 and Scope 2 baseline emissions, and provide virtual training and education to the accountable staff. A pre- and post-survey design was used to measure the knowledge and readiness of the staff after the implementation of the GHG inventory training. (3) Results: The GHG inventory process was validated through an external verification process and the measurement of Scope 1 and Scope 2 baseline GHG emissions was completed and verified for accuracy through a data comparison review. The pre-post-training survey showed an increase in the knowledge and readiness of staff in maintaining a GHG inventory. (4) Conclusions: This work shows the feasibility of obtaining baseline GHG emissions data at large medical centers. It represents the initial phase of the overarching goal to develop site-wide and system-wide carbon reduction strategies and a climate action plan within this health system.

To accomplish IMO's emissions reduction targets, the Chinese government has established emission control areas and implemented strict sulfur limitation policies. Faced with the downturn in the shipping industry and the challenge of insufficient supply of compliant fuel, Hong Kong and Shenzhen in China have implemented different low-sulfur fuel subsidy policies. Therefore, it is particularly important to study the air pollution control mechanism considering low sulfur fuel subsidy policy. Firstly, the non-cooperative game models considering low-sulfur fuel subsidies are constructed. Secondly, the mechanisms of various factors affecting port pricing, throughput and profit are analyzed. Then, a case study is conducted by using AIS data of container ships in Shanghai Port and Ningbo Zhoushan Port. The study reveals that whether the container service price of the leader port increases or decreases, the follower port always take corresponding follow-up measures. In both sequential and simultaneous game, the profit difference of the leader port is positively related to the subsidy ratio of the port’s own and negatively related to the coefficient of the competitor's subsidy. In conclusion, the low-sulfur fuel subsidy policy has a significant positive impact on the step-by-step implementation of more stringent pollution reduction policies in port waters.

A scientific carbon accounting system can help enterprises reduce carbon emissions. This study took the enterprise in the Yangtze River basin as a case study. The accounting classification of carbon emissions in the life cycle of lime production was assessed, and the composition of the sources of carbon emission was analyzed, covering mining explosives, fuel (diesel, coal), electricity and high temperature limestone decomposition. Using the IPCC emission factor method, a carbon life cycle emission accounting model for lime production was established. We determined that a total of 354,200 tons of carbon emissions were generated from producing 321,000 tons of lime in a year. The decomposition of limestone at a high temperature was the largest carbon emission source, accounting for 62.34% of the total carbon emission. Coal combustion was also an important source of carbon emissions, accounting for 32.66% of total carbon emissions. The carbon emission for one ton of activated lime was 1.46kg, 1.49kg, 1100kg and 1102.95kg respectively for the open-pit, mining stage, crushing stage, and the calcination stage. Based upon the main sources of carbon emission for lime production, carbon emission reduction should focus on CO2 capture technology, fuel optimization and energy control. Using our analysis of carbon emissions, the carbon emission factor of producing unit quicklime of the lime enterprise in the Yangtze River basin was determined. Furthermore, the research into carbon emission reduction for lime production can provide a point of reference for the promotion of carbon neutrality in the same industry.

The global transport sector of the world economy contributes about 15% of the Greenhouse Gas (GHGs) emissions in the world today. The University of Saskatchewan has pursued the green energy transition over the years. They have spearheaded diverse sustainability projects and agendas, due to the importance of curbing climate change and advancing sustainability. The transport system in the university campus is one area of focus where the Sustainability Office plans to introduce some innovations, as a way of curbing GHG emissions while also advancing sustainability practice in the university campus. The study carried out an economic benefit analysis on the campus fleet (consisting of 91 ICE vehicles) to determine if it is economically or financially feasible to transition from Internal Combustion Engine (ICE) or PVs (Petrol Vehicles) to Electric Vehicles (EVs). The analysis used RETScreen Expert software for analyzing renewable energy technology projects. The variables of Payback Period (PBP), cash flow projections, savings made from transitioning (fuel cost savings and energy cost savings), Benefit-Cost-ratio, GHG emission reduction potential, etc. were analyzed. The findings revealed that the GHG emission from the campus fleet will be reduced by 100% (this will result in the removal of about 298.1 tCO₂ from the environment). Also, the fleet manager will save approximately $129,049 (88.9%) in fuel costs. Apart from these, the return on investment will be achieved in year 5 (all things being equal), but can be reduced to year 2 if the vehicles are put into constant and active use (eliminating most idle times. Also, the Sustainability Office will be making a GHG reduction revenue of $14,906.

Integrated photovoltaic-fuel cell (IPVFC) systems, amongst other integrated energy generation methodologies are renewable and clean energy technologies that have received diverse research and development attentions over the last few decades due to their potential applications in a hydrogen economy. This article systematically updates the state-of-the-art of IPVFC systems and provides critical insights into the research and development gaps needed to be filled/addressed to advance these systems towards full commercialisation. The design methodologies, renewable energy-based microgrid and off-grid applications, energy management strategies, optimisations and the prospects as self-sustaining power source were covered. IPVFC systems could play an important role in the upcoming hydrogen economy since they depend on solar hydrogen which has almost zero emissions during operation. Highlighted herein are the progresses as well as the technical challenges requiring research efforts to solve to realise numerous potential applications of IPVFC systems such as in unmanned aerial vehicles, hybrid electric vehicles, agricultural applications, telecommunications, desalination, synthesis of ammonia, boats, buildings, and distributed microgrid applications.

Turning ships in port turning basins is an important and responsible operation, mainly involving the ship itself and the port tugs. Such operations involve many maneuvers that consume a lot of energy (fuel) and emit a lot of emissions. Turning basins in harbors and quay approaches are in most cases relatively shallow. The paper examines the turning of ships in port turning basins using harbor tugs, the effect of shallow depth on ship turning, energy (fuel) consumption and the generation of emissions during such maneuvers of harbor tugs. The paper presents the developed theoretical models, and the experimental results on theoretical models, which were verified on real ships and using calibrated simulators. Discussions and conclusions prepared on the basis of the research base. The use of the developed methodology makes it possible to increase shipping safety, optimize maneuvers and reduce energy (fuel) consumption when turning ships in the port and at the same time reduce the amount of fuel consumed by port tugs and reduce the number of emissions of tugs during such operations.

The purpose of this research was to analyze the moderating effect of clean energy innovation on the relationship between corporate carbon footprint and corporate profits in those industrial sectors associated with high demand for fossil fuels in which it is "hard to abate" CO₂e emissions. It used a longitudinal research design, in particular a panel study under a structural equation modeling (SEM) approach, based on partial least squares. For the longitudinal moderation analysis, this research employed the Bayesian method by defining a multiple-indicator latent growth curve model (B-LGC model). A global sample was used consisting of 7,827 firm-year observations between 2015 and 2021 corresponding to 167 international firms. The results revealed a very significant impact of the corporate carbon footprint on corporate profits. Likewise, the results showed that innovations in clean energy, when measured as the consumption of renewable energy, positively moderates the relationship between the greenhouse gas emissions from the value chain associated with Scope 3 of the Greenhouse Gas (GHG) Protocol, and the gross profit margin obtained. Besides the academic contribution represented by the moderating effect of clean energy innovation, these findings imply that a more detailed understanding of the emissions of the entire value chain (Scope 3 CO₂e) by executives and managers of high emitting CO₂e companies represents an effective mechanism to obtain higher profits, create competitive advantages and, at the same time, achieve a net zero emissions strategy. More importantly, public policy makers will be able to use these results to revise CO₂e-related policies paying more attention to the Scope 3 CO₂e emissions produced by these companies, to formulate regulatory and control mechanisms that stimulate clean energy innovation.

Air pollution is a leading cause of death worldwide, and has a profound impact on the planet's climate and ecosystems. A substantial portion of air pollution is attributable to Ocean Going Vessels (OGVs). In light of this, international regulations have been put in place to mitigate air pollutant emissions from OGVs. While studies have indicated that these regulations can create significant health, environmental, and economic benefits, there remains a research gap regarding their specific impact on enhancing air quality. The aim of this study is to investigate how the implemented regulations have affected air quality in the Southern North Sea. The study found that the international regulations on ship emissions have successfully led to a decline in SO2 emissions from OGVs in the Southern North Sea, which resulted in a reduction of ambient SO2 concentrations inland, leading to positive effects on public health and the environment. However, it was projected that their proportion is tend to increase in the following years. Moreover, the study revealed that Exhaust Gas Cleaning Systems (EGCS) present significant concerns. They were significantly more frequently found to be non-compliant, and more alarmingly, they emit notably higher average levels of SO2. It also turned out that international regulations in the southern North Sea have less effect on the reduction of NOx emissions from OGVs than expected. The NOx emissions from OGVs will even account for an alarming 40% of the total domestic NOx emissions for the Belgian Region by 2030.

Alternative fuels containing biocomponents produced in various technologies are introduced in aviation to reduce its carbon footprint but there is little data describing their impact on the performance and emissions of engines. The purpose of the work is to compare the performance and gas emissions produced from two different jet engines: the GTM-140 microturbine and the full-size DGEN380 turbofan, powered by blends of Jet A-1 and one of two biocomponents: 1) ATJ and 2) HEFA produced from used cooking oil (UCO) in various concentrations. The acquired data will be used to develop an engine emissivity model to predict gas emissions. Blends of the mineral fuel with synthetic components were prepared in various concentrations, and their physicochemical parameters were examined in the laboratory. Measurements of emissions from both engines were carried out in selected operating points using the Semtech DS gaseous analyzer and the EEPS spectrometer. The impact of tested blends on engine operating parameters is limited, and their use does not carry the risk of a significant decrease in aircraft performance or increase in fuel consumption. Increasing the content of biocomponents causes a noticeable rise in the emission of CO and slight increase for some other gasses (HC and NOx), which should not, however, worsen the working conditions of the ground personnel. This implies that there are no contraindications against using tested blends for fuelling gas-turbine engines.

In order to assess the human exposure risks from the release of contaminants from water pipes made of polyvinyl chloride (PVC), experiments were carried out by subjecting the PVC pipe material to burning and leaching conditions followed by analysis of the emission and leachate samples. The emissions of burning pipes were analyzed by both infrared spectrometry and gas chromatography-mass spectrometry (GC-MS). The emission results indicate the presence of chlorinated components including chlorine dioxide, methyl chloride, methylene chloride, allyl chloride, vinyl chloride, ethyl chloride, 1-chlorobutane, tetrachloroethylene, chlorobenzene, and hydrogen chloride were detected in the emissions of burning PVC pipes. Furthermore, the concentrations of benzene, 1,3-butadiene, methyl methacrylate, carbon monoxide, acrolein, and formaldehyde were found at levels capable of affecting human health adversely. The analysis of PVC pipe leachates using GC-MS shows that there are 40-60 tentatively identified compounds, mostly long-chain hydrocarbons such as tetradecane, hexadecane, octadecane, and docosane, were released when the burned PVC materials were soaked in deionized water for one week. Quantitative analysis shows that 2-butoxyethanol, 2-ethyl-1-hexanol, and diethyl phthalate were found in the burned PVC polymer at the average levels of 2.7, 14.0, and 3.1 micrograms per gram (g/g) of pipe material. This study has significant implications for understanding the benzene contamination of drinking water in the aftermath of wildfires that burned polymer pipes in California.

Three physical elements are missing from the conventional formalism of quantum photonics: 1) the quantum Rayleigh spontaneous and stimulated emissions; 2) the unavoidable parametric amplification; and 3) the mixed time-frequency spectral structure of a photonic field which specifies its duration or spatial extent. As a single photon enters a dielectric medium, the quantum Rayleigh scattering prevents it from propagating in a straight-line, thereby destroying any possible entanglement. A pure dynamic and coherent state composed of two consecutive number states, delivers the correct expectation values for the number of photons carried by a photonic wave front, its complex optical field, and phase quadratures. The intrinsic longitudinal and lateral field profiles associated with a group of photons for any instantaneous number of photons are independent of the source. These photonic properties enable a step-by-step analysis of the correlation functions characterizing counting of coincident numbers of photons or intensities with unity visibility interference, spanning the classical and quantum optic regimes

Cement manufacturing is one of the most energy-intensive industries in the world. Most of the cost of producing cement is accounted by fuel consumption and power expenditures. Thermal power plants are the major source of electricity in Pakistan. But they are not efficient and environmentally friendly. This study simulates four different models for five cement plants of Pakistan on Homer Pro software and compares the optimal solutions based on the net present cost (NPC), levelized cost of electricity (LCOE) and greenhouse gas (GHG) emissions. Model-1 consists of solar panels, electrolyzer, hydrogen tank, hydrogen generator and converter. Model-2 has only a diesel generator and acts as a base case in this study. Model-3 has solar panels and a battery-converter system. In Model-4, diesel generators, solar panels and converters are considered. Based on NPC, the most optimal model is Model-4, having a 0.249 $/KWh LCOE in islanded systems. The NPC and operating costs are US$540 million and US$ 32.5 million per year, respectively, with a 29.80% reduction in CO2 emissions when compared to the base case. Based on GHG emissions, Model-1 and Model-3 are the best models with 0% GHG emissions. Sensitivity analyses is also performed using the parameters of load, inflation rate and discounted rate. The results prove that the proposed hybrid micropower systems (HMS) can sustainably provide electricity for 24 hours a day to the sites under consideration with minimum objectives.

Primary energy consumption is one of the key drivers of global CO₂ emissions that, in turn, heavily depend on the efficiency of involved technologies. Either the improvement in technology efficiency or the expansion of non-fossil fuel consumption require large investments. The planning and financing of such investments, by policy makers or global energy firms, require, in turn, reliable measures of associated global spreads and their evolution in time. In this paper, our main contribution is the introduction of index measures for accessing global spreads (that is, measures of inequality or inhomogeneity in the statistical distribution of a related quantity of interest) of technology efficiency and CO₂ emission in primary energy consumption. These indexes are based on the Gini index, as used in economical sciences, and generalised entropy measures. Regarding primary energy sources, we consider petroleum, coal, natural gas and non-fossil fuels. Between our findings, we attest some stable relations in the evolution of global spreads of technology efficiency and CO₂ emission, and a positive relation between changes in global spreads of technology efficiency and use of non-fossil fuel.

In this paper a dynamic relationship between the CO2 emissions in Finland, Norway and Sweden is presented. With the help of a VAR(2) model, and using the Granger terminology, it is shown that the emissions in Finland are affecting those in Norway and Sweden. Other aspects of this dynamic relationship are presented as well.

A cross-flow ultrafiltration harvesting system of a pre-concentrated microalgae culture was tested in an innovative anaerobic-based WRRF. The microalgae culture was cultivated in a membrane photobioreactor fed with the effluent from an anaerobic membrane bioreactor treating sewage. These harvested microalgae biomass was then anaerobically co-digested with primary and secondary sludge from the water line. Depending on the needs of this anaerobic co-digestion, the filtration harvesting process was evaluated intermittently over a period of 212 days for different operating conditions, mainly the total amount of microalgae biomass harvested and the desired final total solids concentration (up to 15.9 g·L1 with an average of 9.7 g·L1). Concentration ratios of 15-27 were obtained with average transmembrane fluxes ranged from 5 to 28 L·m2·h1. Regarding membrane cleaning, both backflushing and chemical cleaning resulted in transmembrane flux recoveries that were, on average, 21% higher than those achieved with backflushing alone. The carbon footprint assessment shows promising results as the GHG emissions associated with the cross-flow ultrafiltration harvesting process could be less than the emissions savings associated with the energy recovered from the biogas production from the anaerobic valorisation of the harvested microalgae.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

The goal of this study was to evaluate the feasibility of methods based on the Worldwide Harmonized Light-Duty Vehicles Test Procedure Brake Cycle to measure brake wear particle emissions for currently used electrified vehicles. Our results indicated that reducing brake friction work reduced brake wear particle emissions. Commercially available, plug-in hybrid electric vehicles reduced emissions by 85% for PM₁₀, 78% for PM_2.5, and 87% for particle numbers (PNs) compared to vehicles with internal combustion engines. Brake friction work showed a linear relationship with PM₁₀ and PM_2.5. Nanoparticle PM emissions tended to increase slightly with regenerative braking, but did not contribute significantly to the overall PM percentage. the emission events of high number concentrations of nuclei mode particles (<20 nm in diameter) in electric vehicle brake assemblies designed for regenerative braking use under high-temperature, high-load braking conditions with full-friction brakes. The nuclei mode particles amplified the PN emissions and led to a high variability. In strict regulatory certification tests, where measurement reproducibility and stability are required, it is appropriate to measure PNs under brake conditions appropriate for the actual use of electric vehicles rather than under full-friction brake conditions or to remove particle measurements smaller than 20 nm.

Cement industry is one of the highest energy consuming industries. The quantity of fuel and energy needed accounts for most of the cost of cement manufacturing. Thermal power plants generate electricity but are harmful and ineffective by nature. As a backup mechanism to account for main grid failures, batteries can be utilized. In this paper the first ever investigation on battery’s depth of discharge (DOD) for four different kinds of battery technologies is carried out in the framework of cement industry. The intended battery technologies are the lead-acid battery (LA), lithium-ion battery (Li-ion), vana-dium redox battery (VR), and nickel–iron battery (Ni-Fe). Four hybrid energy generation models (HEGMs) for five cement plants of Pakistan using the HOMER pro software are proposed. Cement plants includes Askari Cement Plant, Wah (ACPW); Bestway Cement Plant, Kalar Kahar (BCPKK); Bestway Cement Plant, Farooqia (BCPF); Bestway Cement Plant, Hattar (BCPH); and DG Cement Plant, Chakwal (DGCPC). HEGM-1 comprises of a diesel generator (DGen), a photovoltaic system (PV), a converter, and a battery system. HEGM-2 comprises of a PV system, a converter, and a battery system. HEGM-3 is the grid-connected version of HEGM-1 and HEGM-4 is the grid-connected version of HEGM-2. A base-model consisting of grid only is used as a reference. A multi-criteria decision analysis (MCDA) is performed by formulating a cumulative objective function (COF) which includes net present cost (NPC), levelized cost of energy (LCOE), and greenhouse gas (GHG) emissions. The principal objective is the maximization of COF while simultaneously minimizing the objectives (NPC, LCOE and GHG emissions), based on optimal battery technology and DOD. The results reveal that VR is the most suitable battery technology with 10% DOD. It is achieved for DGCPC with HEGM-3 with 61.49% of NPC, 78.62% of LCOE and 84.00% of GHG emissions reduction as com-pared to the base model.

The paper presents data from a monthly campaign for the elemental composition of PM10 in a specific receptor Kotórz Mały (Opole Voivodeship) located in the vicinity of a moderately inhabited rural area, measured in one-hour samples with the use of the PX-375 analyzer by the Horiba company. The hourly variability of SO2, NO, NO2, CO, O3 concentrations as well as the variability of meteorological parameters were also determined. On average, during the entire measurement period, the elements related to PM10 can be arranged in the following order: As<V<Ni<Pb<Cr<Mn<Cu<Ti<Zn<K<Fe<Ca<Al<Si<S. Trace elements, including toxic elements, such as As, V, Ni, Pb, Cr, Mn, were present in low concentrations, not exceeding 10 ng/m3 (average daily value). These elements had fairly even concentrations, daily and hourly. The concentrations of the main elements in the PM10 in the receptor are subject to strong hourly changes related not only to changes in the structure of the sources identified in the statistical analysis but mainly to wind speed and direction changes (soil and sand particles pick-up and inflow of pollutants from coal combustion). It has been shown that the transport emission in the receptor can have an intense effect on PM10 in the afternoon.

A testable hypothesis with quantitative predictions is put forward, proposing that strong acids produced on land are a major cause of increasing atmospheric pCO2. Our modelling analysis of reactions by dissolved inorganic carbon shows that increasing atmospheric CO2 could be caused thermodynamically by falling land surface pH values. This hypothesis challenges the imbalance assumed between the global uptake of CO2 by photosynthesis and emissions of CO2 from all sources, including the combustion of fossil fuels. Strong acids generated by oxygen from reduced nitrogen and sulphur emits CO2 almost stoichiometrically from dissolved bicarbonate in the pH range of most global soils from pH 6.5 to above 8. Each general decrease of aqueous pH value of 0.01 units from acidification of surface water potentially increases the pCO2 in the atmosphere by about 7 ppmv. Contrary to prevailing assumptions that CO2 emissions from combusting fossil fuels can remain in the atmosphere for more than a millennium, such emissions may be partly nullified by global greening from enhanced rates of photosynthesis as well as oceanic absorption. The surface pH value of the ocean has been shown to decrease as atmospheric pCO2 rises. Therefore, our qualitative estimates of increasing atmospheric CO2 driven by irreversible acidification on land are critical and need broad scale validation. To the extent that significant acidification of the land is occurring, through export of alkaline produce, the use of artificial nitrogen fertilisation and possible other causes, the prevailing methods of reducing CO2 emissions will fail. However, these acidifying processes on land have not been considered by previous biogeochemical reviews. Despite counter measures, including carbon capture and geological storage, the increasing Keeling curve for pCO2 may continue to rise because zero carbon policies do not address such a major cause. This hypothesis can be tested by in situ experiments in neutral soils and water, designed to compare CO2 emissions under the acidifying conditions described in this article with those when corrective counter measures are applied.

A controlled ammonia (NH₃) release experiment was performed at a grassland site to quantify the effect of dry deposition, at the field scale between the source and the receptors (NH₃ measurement locations), on the estimates of emission rates by means of inverse dispersion modelling. NH₃ was released for 3 hours at a constant rate of Q = 6.29 mg s⁻¹ from a grid of 36 orifices spread over an area of 250 m². The increase in line-integrated NH₃ concentration was measured with open-path optical miniDOAS devices at different locations downwind of the artificial source. Using a backward Lagrangian stochastic (bLS) dispersion model (bLSmodelR), the fraction of the modelled release rate to the emitted NH₃ (Q_bLS/Q) was calculated from the measurements of the individual instruments. Q_bLS/Q was found to be systematically lower than 1, on average between 0.69 and 0.91, depending on the location of the receptor. We hypothesized that NH₃ dry deposition to grass and soil surfaces was the main factor responsible for the observed depletion of NH₃ between source and receptor. A dry deposition algorithm based on a deposition velocity approach was included in the bLS modelling. Model deposition velocities were evaluated from a ‘big‑leaf’ canopy resistance analogy. Canopy resistances (generally termed Rc) that provided Q_bLS/Q = 1 ranged from 75 to 290 s m⁻¹, showing that surface removal of NH₃ by dry deposition can plausibly explain the original underestimation of Q_bLS/Q. The inclusion of a dry deposition process in dispersion modelling is crucial for emission estimates, which are based on concentration measurements of depositing tracers downwind of homogeneous area sources or heterogeneously distributed hot spots, such as e.g. urine patches on pastures in the case of NH₃.

The increasing social pressure for decarbonization has placed businesses under considerable scrutiny to actively reduce carbon emissions. A critical step towards achieving this objective is to shift conventional production and consumption systems to more sustainable alternatives. Thus, there is the emergent need to understand the patterns and drivers of the transformative business models (BMs) that underpin that shift. This study adopts a mixed-methods approach that integrates different literature streams--including Sustainability Transitions Theory (STT), Strategic Niche Management (SNM), and the Business Models approach--and stakeholders’ interviews to investigate the key elements of business models that lead towards sustainable practices. This research examines the organizational arrangements of European start-ups operating between 2014 and 2020. The transformation towards decarbonized production and consumption is characterized by efficient combination of business strategies that incorporate advanced technologies (ATs), such as artificial intelligence (AI), machine learning (ML) and its algorithms, along with sustainable elements, resulting in transformative business models. By exploring the driving elements behind the transition to low-carbon approaches, this study fills a significant gap in the existing literature on business models. The findings from this research also hold relevance for policymakers to promote decarbonization.

The building sector has a big potential to reduce the material resource demand needed for building construction and therefore, greenhouse gas (GHG) emissions. Digitalisation can help to make use of this potential and improve sustainability throughout the entire building’s life cycle. One way to address this potential is through the integration of Life-Cycle Assessment (LCA) into the building process by employing Building Information Modelling (BIM). BIM can reduce the effort needed to carry out an LCA and therefore facilitate the integration into the building process. A review of current industry practice and scientific literature shows two main approaches to address BIM-LCA integration. Either the LCA is performed in a simplified way at the beginning of the building process, or it is done at the very end when all the needed information is available, but it is too late for decision-making. One reason for this is the lack of methods, workflows and tools to implement BIM-LCA integration over the entire building process. Therefore, the main objective of this study is to develop an integrated BIM-LCA workflow implemented into a method for the whole building process using an existing structure for cost estimation. A tool is created and used in a case study in Switzerland to test the developed approach. The results of this study show that LCA can be performed continuously in each building phase over the entire building process using existing BIM modelling techniques. The main benefit of this approach is that the re-work caused by the need for re-entering data and the usage of many different software tools that characterise most of the current LCA practices is minimised. Furthermore, decision-making, both at the element and building levels, is supported.

Accurate prediction of mercury content emitted from fossil-fueled power stations is of utmost importance for environmental pollution assessment and hazard mitigation. In this paper, mercury content in the output gas of power stations’ boilers was predicted using an adaptive neuro-fuzzy inference system (ANFIS) method integrated with particle swarm optimization (PSO). The input parameters of the model include coal characteristics and the operational parameters of the boilers. The dataset has been collected from 82 power plants and employed to educate and examine the proposed model. To evaluate the performance of the proposed hybrid model of ANFIS-PSO model, the statistical meter of MARE% was implemented, which resulted in 0.003266 and 0.013272 for training and testing, respectively. Furthermore, relative errors between acquired data and predicted values were between -0.25% and 0.1%, which confirm the accuracy of the model to deal nonlinearity and representing the dependency of flue gas mercury content into the specifications of coal and the boiler type.

The objective of this study was to identify the factors determining a company’s corporate governance related to climate change. We analyzed the effect of various sustainability corporate governance variables on the disclosure level of climate change governance. These variables included facts such as having a dedicated sustainability executive and board committee, the mediating effect of female representation on the board of directors, number of reporting years according to TCFD, membership in a sustainability index, MSCI ESG rating, the existence of a corporate climate transition plan, a mention of the UN Global Compact and GRI, company location, as well as company size and profitability. By adopting a multi-theoretical framework that included stakeholder theory as well the legitimacy and agency theory, the underlying research study used a sample of 100 of the largest global companies by market capitalization and their reporting for the year 2020. Based on 1,400 observations for fiscal year 2020 and using correlation analysis, univariate and linear multiple regressions, we find a positive association between having a climate transition plan in place, being a leader in sustainability according to MSCI ratings, and being a DJSI constituent and the propensity to disclose information on governance for climate change. In addition, we find a company with a dedicated sustainability executive show an increased tendency to be transparent on climate governance issues. Furthermore, having a company location in a developed country is significantly and positively associated with climate change governance. Surprisingly, gender diversity in the corporate board or having a sustainability board committee did not show any significant correlation between a higher climate change governance level. The same was true for companies being active in either the extractive or non-extractive sector. Companies referring to the Global Reporting Initiative (GRI) or UN Global Compact also did not score higher in climate change governance. Neither did corporate profitability or size play a significant role. Our results are robust to variations and provide valuable insights for researchers, academics, executives, practitioners as well as regulators. As more and more companies are shifting towards a climate change reporting framework, it is of paramount importance that we are able to determine the contributing variables that lead to effective climate change corporate governance. Our results are inconsistent with stakeholder theory and are strongly suggesting that a diversified board and the existence of a sustainability committee that meets often/sufficiently may not necessarily lead to a higher level of transparency/quality regarding climate change. While more research is needed, knowing that a dedicated sustainability executive as well as having a climate plan in place can make a difference in climate change reporting, can be very beneficial to many corporate stakeholders. Given the current urgent climate change situation and the crucial role that corporation play in it, dedicated sustainability positions and committees need to be established. The findings could be useful for managers as well as governmental standards setter and regulators who are interested in improving corporate practices dealing with climate change. This study applies STATA software with various regression models to empirically test the relationship between CG and other variables and corporate climate change reporting.