The capacitor-mismatch among diverse defects caused by the manufacturing process variations significantly affects the linearity of capacitor-array used to implement the capacitive digital-to-analog converter (CDAC) in the successive-approximation-register (SAR) analog-to-digital converter (ADC). Accordingly, the linearity of the SAR ADC is limited by that of capacitor-array, resulting in serious yield loss. This paper proposes an efficient foreground self-calibration technique to enhance the linearity of the SAR ADCs by mitigating the capacitor-mismatch based on the split ADC architecture along with variable capacitors. In this work, two ADC channels (i.e., ADC1 and ADC2) for the split ADC architecture include their capacitive DACs (CDACs) whose binary-weighted capacitor-arrays consist of variable capacitors. A charge-sharing SAR ADC is used for each ADC channel. In the normal operation mode, their digital outputs are averaged to be the final ADC output, as in a conventional split ADC. In the calibration mode, every single binary-weighted capacitor for the two ADCs is sequentially calibrated by making parallel or/and antiparallel connection among two or thee capacitors from the two channels. For instance, because the capacitors of the CDACs ideally exhibit the binary-weighted relation as Cn=2×Cn−1, variable capacitor Cn of ADC1 can be updated to be closest to the sum of Cn−1 of ADC1 and Cn−1 of ADC2 for the calibration. For the process, the two capacitor-arrays of the two ADCs can be reconfigured to be connected to each other, so that Cn of ADC1 can be connected with two of Cn−1 of ADC1 and ADC2 in antiparallel. The two voltages at the top and the bottom plates of the CDAC are compared by a comparator of ADC1, and the comparison results are used to update Cn. This process is iterated, until Cn is in agreement with the sum of two of Cn−1. Finally, all the capacitors can be calibrated in this way to have the binary-weighted relation. The simulation results based on the proposed work with a split SAR ADC model verified that the proposed technique can be practically used, by showing that the total-harmonic-distortion and the signal-to-noise-and-distortion ratio were enhanced by 21.8-dB and 6.4-dB, respectively.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

The feeling of beauty is one of the positive human feelings. In architecture and design, it is associated with forms appropriate to their purpose. The usefulness of products to meet needs is also important. They are well received by users. The task of designers is to achieve perfection in their work. The rational design and use of artificial living environments are expressions of concern for natural resources (sustainable environment). These issues are addressed, i.e., by an interdisciplinary initiative of the New European Bauhaus. The aim of the paper is to expand knowledge about beauty and utility. They are important when choosing mass-produced goods. The article uses research methods: interpretive research, analyses, comparisons, logical argumentation, etc. Experimental qualitative research using a checklist was used. The results expand the knowledge on the selected topic and research scope of the research of the paper. The survey can be used to rationally evaluate architecture, interiors, and design facilities. It can be helpful for various aesthetic and functional strategies dedicated to different users. The paper demonstrates the role of beauty and functionality in the built environment. They are analyzed in the context of social and technical conditions, as well as contemporary sustainable design

This study considers the change-point test problem for time series based on the self-normalization ratio statistic test, which is constructed using residuals obtained from a support vector regression (SVR)-autoregressive moving average (ARMA) model. Under the null hypothesis, the series is a stationary process, and our test statistic converges to a non-degenerate distribution. Under the alternative hypothesis, there are change-points in the time series, and the self-normalization test statistic diverges to infinity. The simulations show that our proposed new test has better finite sample performance than other SVR-based tests in the literature. Finally, we illustrate its usefulness by analyzing two actual data sets.

Weaving technology can convert two-dimensional structures such as ribbons into three-dimensional structures by specific connections. However, most of the 3D structures fabricated by conventional weaving methods using straight ribbons have some topological defects. In order to obtain smoother continuous 3D surface structures, Baek et al. proposed a novel weaving method using naturally curved (in-plane) ribbons to fabricated three-dimensional curved structures and using this method to weave new spherical weave structures that are closer to perfect spheres. We believe that this new spherical weave structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated the buckling characteristics of different types of spherical weave structures by the combination of test and finite element method. The results of calculations and experiments show that the failure mode of the spherical weave structure under vertical loading can be divided into two stages: a flat contact region forms between the spherical weave structure and the rigid plate and inward dimple of ribbons. The spherical weave structures using naturally curved (in-plane) ribbon weaving have better buckling stability than those woven with straight ribbons. The vertical buckling load of spherical weave structures using naturally curved ribbon increases with the width and thickness of the ribbon. In addition, this paper combines test, theoretical and finite element analysis to propose the buckling load equation and buckling correction factor equation for the new spherical weave structure under vertical compression load.

The value of QuantiFERON in the diagnosis of tuberculosis and in the monitoring of the response to anti-tuberculosis treatment is unclear. The aims of this study were to evaluate the accuracy of the QuantiFERON-TB Gold In-Tube (QFT-GIT) test in the diagnosis of tuberculosis and in the monitoring of the response to anti-tuberculosis treatment in patients with active pulmonary tuberculosis (PTB). Between January 2013 and December 2015, 128 cases with active PTB and 128 controls with no mycobacterial infection, matched by age (within 3 years) and by the week that they visited Tainan Chest Hospital, were enrolled in the study. Serial testing by QFT-GIT at baseline and after 2 and 6 months of treatment was performed. At these time points, a comparison of the performance of QFT-GIT with that of sputum culture status among study subjects was conducted. Compared to baseline, 116 (87.2%) cases showed a decreased response, whereas 17 (12.8%) showed persistent or stronger interferon-gamma (IFN-γ) responses at 2 months. Their IFN-γ responses declined significantly from baseline to 2 months (median, 6.32 vs. 4.12; P < 0.005). The sensitivity values of the QFT-GIT test for the detection of pulmonary tuberculosis at cut-off points of 0.35 IU/ml, 0.20 IU/ml, and 0.10 IU/ml were 74.4%, 78.2%, and 80.5%, respectively. The specificity values at cut-off points of 0.35 IU/ml, 0.20 IU/ml, and 0.10 IU/ml were 66.2%, 63.9%, and 57.1%, respectively. Our results support the QFT-GIT assay as a potential tool for diagnosing tuberculosis and for monitoring the efficacy of anti-tuberculosis treatment.

Microvascular self-healing composite materials have significant potential for application and their mechanical properties need in-depth investigation. In this paper, tensile and compressive properties of woven fabric carbon fiber reinforced polymers (CFRP) laminates containing three-dimensional microvascular channels were investigated experimentally. Several detailed finite element (FE) models were established to simulate the mechanical behavior of the laminate and the effectiveness of different models were examined. The damage propagation process of the microvascular laminates and the influence of microvascular parameters were studied by the validated models. The results show that microvascular channels arranged along the thickness direction (z-direction) of the laminates are critical locations under the loads. The channels have minimal effect on the stiffness of the laminates but causing a certain reduction in strength, which varies approximately linearly with the z-direction channel diameter within its common design range of 0.1~1mm. It is necessary to consider the resin-rich region formed around microvascular channels in the warp and weft fiber yarns of the woven fabric composite when establishing the FE model. And the layers in model should be assigned with equivalent unidirectional ply material in order to calculate the mechanical properties of laminates correctly.

Within the field of guilt and shame, two competing perspectives have been advanced. The first, the social-adaptive perspective, proposes that guilt is an inherently adaptive emotion and shame is an inherently maladaptive emotion; thus, those interested in moral character development and psychopathology should work to increase an individual’s guilt-proneness and decrease an individual’s shame-proneness. The functionalist perspective, in contrast, argues that both guilt and shame can serve a person adaptively or maladaptively—depending on the situational appropriateness, duration, intensity, and so forth. This paper reviews the research conducted supporting both positions, critiques some issues with the most widely used guilt- and shame-proneness measure in the social-adaptive research (the TOSCA), and discusses the differences in results found when assessing guilt and shame at the state versus trait level. The conclusion drawn is that although there is broad support for the functionalist perspective across a wide variety of state and trait guilt/shame studies, the functionalist perspective does not yet have the wealth of data supporting it that has been generated by the social-adaptive perspective using the TOSCA. Thus, before a dominant perspective can be identified, researchers need to (1) do more research assessing how the social-adaptive perspective compares to the functionalist perspective at the state level, and (2) do more trait research within the functionalist perspective to compare functionalist guilt- and shame-proneness measures with the TOSCA.

Background and Objective: Intimate relationships hold significant importance during emerging adulthood. This study aimed to investigate the critical determinants of perceived well-being in friendship relationships during emerging adulthood.Method: Using a quantitative approach, a sample of 726 undergraduate students from the Ferdowsi University of Mashhad were selected through convenience sampling. They completed the Interpersonal Behaviors Questionnaire (IBQ), the Compassionate and self-image goals scale (CSIGS), the Basic Need Satisfaction in Relationships Scale (BNS-RS), the Interpersonal Needs Questionnaire (INQ-10), Friendship Self-Regulation Questionnaire (SRQ-F), Interpersonal Behaviors Questionnaire-Self (IBQ-self), State Level Subjective Vitality Scale (SVS-SL), the Perceived Relationship Quality Component (PRQC), and the Basic Empathy Scale (BES). Data analysis was conducted using Partial Least Squares Structural Equation Modeling (PLS-SEM).Results: The results indicated that the critical determinants in predicting perceived well-being in friendship relationships were, in order, goals in friendship relationships, friendship self-regulation, perceived support of basic psychological needs by friends, satisfied basic psychological needs, frustrated psychological needs, and supporting the basic psychological needs of friends.Conclusion: The findings demonstrate that self-determination theory (SDT) provides a coherent framework for explaining perceived well-being in friendships.

This study aimed to evaluate the diagnostic roles of various immunohistochemical markers in urothelial carcinoma in situ (uCIS) through a meta-analysis and review of diagnostic test accuracy. Immunohistochemical markers CK20, CD44, AMACR, and p53 were evaluated in the present study. We analyzed the expression rates of immunohistochemical markers and compared their diagnostic accuracies. The estimated expression rates were 0.803 (95% confidence interval [CI]: 0.726–0.862), 0.142 (95% CI: 0.033–0.449), 0.824 (95% CI: 0.720–0.895), and 0.600 (95% CI: 0.510–0.683) for CK20, CD44, AMACR, and p53, respectively. In the comparison between uCIS and reactive/normal urothelium, the expression of CK20, AMACR, and p53 in uCIS was significantly higher than in reactive/normal urothelium. CD44 showed significantly lower expression in uCIS than in the reactive/normal urothelium. Among the markers, AMACR had the highest sensitivity, specificity, and diagnostic odds ratio. The AUC on SROC was the highest for CK20. In conclusion, immunohistochemical markers, such as CK20, CD44, AMACR, and p53, can be useful in differentiating uCIS from reactive/normal urothelium.

The silanol activity and trace metal detection methods for chemically bonded silica gels were evaluated in silico. Test compounds with large molecular sizes may demonstrate negative results because of the possibility of indirect hydrogen bonding via short alkyl groups or siloxane of the silica gels. This hypothesis was based on the observation of weak hydrogen bonding energy values similar to those observed in the study of the alkyl group effect on the hydrogen bonding of alkanols. Consequently, smaller molecules may be a better choice for the analysis of bonded-phase quality.

Wildfires present a significant risk to societies globally due to population growth, con- centrated activities, climate change, and extreme environmental conditions. To establish effective fire suppression and management policies, it is crucial to determine whether the distance between ignition points and urban areas is increasing or decreasing. This study analyses 101,597 fires in Spain and California between 2007 and 2015, using the Mann-Kendall test to determine trends. The study analyses the location and cause of fires to determine their distance from human constructions over time at two spatial scales. The findings suggest that wildfires are not moving away from buildings and, in some areas, are moving significantly closer.

Research into health, particularly social and psychological health, is crucial. Ultimately, an in-depth understanding of social and psychological health will more than promote well-being. Technology research is indispensable, particularly concerning health and the built environment, given the need to create holistic and supportive frameworks for well-being. Moreover, because literature reviews establish the foundation for academic inquiries, they provide valuable overviews for foresight into grey research areas, particularly multi-disciplinary research like health technology and the built environment. Hence, this study aims to discover the existing themes on health, technology, and built-environment nexus subjects while revealing the grey areas and suggesting proactive areas for future research. The objectives drove this aim to: 1. investigate the implications of technology for the social and psychological dimensions of health; 2. uncover the likelihood of a nexus between health, technology, and the built environment; and 3. highlight new research perspectives for the concluding seven years of the SDGs (2024–2030). The review results highlighted ten themes around which a nexus exists between health, technology, and the built environment; they also pointed out new research perspectives for the next seven years (up to 2023).

The development of unmanned satellite space technology is increasingly willing, the emergence of medium resolution satellites with sensitivity and spectral variants such as Landsat is very effective in observing environmental changes, while the purpose of this study is to monitor the development of built-in land using image transformation techniques, estimating built-in land changes. The research method uses the NDVI image transformation technique, NDBI and Built Up Index, with Landsat satellite image data obtained from USGS. Accuracy sampling is done by purposive sampling with confusion matrix accuracy test technique. The research results were found. developed land for the period 2004 - 2010 with a percentage of 19.25%, for stages 2010 - 2018 with a percentage of 30.25%. The land development was built based on the area of ​​the highest sub-district in the Kubung area in the early period with a percentage of 7.20% then in the second period with a percentage of 32.23%. The quality of the accuracy of the results of image analysis using confusion matrix technique with an image accuracy level in a field sample of 185 with an image accuracy of 86.04%.

Background: Breast cancer remains a significant health concern among women globally. Despite advancements in awareness and diagnostic techniques, it persists as a leading cause of death, with profound impacts on affected individuals' quality of life. Primary and secondary prevention, including regular screenings and practices like Breast Self-Examination (BSE), are pivotal in ensuring early diagnosis. The NHS in Italy offers screenings for women aged 50-69 every two years, managed by the Local Health Authority. However, the participation rates, especially among the Chinese female population residing in Italy, are not well-understood. Methods: Using a snowball method, we electronically disseminated a survey to investigate how Chinese women living in Italy engage with available NHS screening programs. The survey also explores their practice of BSE, the use and impact of technological tools on prevention, and aims to understand their depth of knowledge and misconceptions about breast cancer. Results: The data revealed a significant gap in breast cancer screening adherence and knowledge among Chinese women in Italy, with a notable discrepancy between the general population and those who have previously encountered cancer. Conclusions: The results highlight the urgent need for interventions that are culturally sensitive, stressing that these actions are not only desirable but essential.

Urban air quality is increasingly being studied as a fraction of the world's population is now living in megacities. In this study, particulate matter (PM) along Taft Avenue, Manila, Philippines, is investigated in terms of its ability to induce genetic damage on human peripheral blood lymphocytes (PBL). Size-segregated roadside air samples were obtained from 2015-2016 near the university gate and analyzed using in vitro micronucleus and cytokinesis-block proliferation tests. While cellular proliferation was unaffected by 0 – 0.1 kg·m-3 of PM1.0 and PM2.5, PBL cells treated with PM2.5 displayed significantly higher micronucleus count (p = 0.03) compared to the cells treated with PM1.0. Atomic Absorption Spectroscopy revealed greater amounts of Cd, Ca, Pb, K, Na, and Zn in PM2.5 compared to PM1.0. The results indicate the differences in composition of the two size fractions of air particulates are associated with their genotoxicities.

While numerous studies have explored the correlation between the built environment and ride-hailing demand, few have assessed their nonlinear interplay. Utilizing ride-hailing order data and multi-source built environment data from Nanjing, China, this paper uses the machine learning method, eXtreme Gradient Boosting (XGBoost), combined with SHapley Additive exPlanations (SHAP) and Partial Dependence Plots (PDP) to investigate the impact of built environment factors on ride-hailing travel demand, including their non-linear and threshold effects. The findings reveal that dining facilities have the most significant impact, with a contribution rate of 30.75%, on predicting ride-hailing travel demand. Additionally, financial, corporate, and medical facilities also exert considerable influence. The built environment factors need to reach a certain threshold or within a certain range to maximize the impact of ride-hailing travel demand. population density, land use mix and distance to the subway station collectively influence ride-hailing demand. The results are helpful for TNCs to allocate network ride-hailing resources reasonably and effectively.

Revolutionizing Lng Plant Construction and its Comprehensive Comparative Analysis And Evaluation Of Modular Design Development Versus Stick-Built Approach For Enhanced Efficiency And Cost-Effectiveness,.Although the utilization of modularization concepts in the LNG industry remains limited, this study focuses on exploring their potential. It is worth noting that modular units typically incur higher costs compared to field erected units due to the additional requirements of structural steel and robustness for transportation purposes.Nevertheless, the increased cost of modularization can often be balanced by conducting the work at the fabrication site instead of on-field construction. This approach reduces the overall project cost by minimizing field construction expenses and shortening the construction schedule. The objective of this paper is to assess and compare LNG modularization options for a newly established LNG facility in comparison to a conventional stick-built plant used as the base case.:The paper delves into various topics related to LNG plant construction, such as the development of modular units, a comprehensive comparison of different options, evaluation of construction schedules and manpower requirements, logistics considerations, and a recommended approach for design and construction. The cost estimates and engineering, procurement, and construction (EPC) schedules are meticulously compared for each option. Additionally, an inshore/near shore gravity base structure (GBS) option is included for further comparison. It is crucial to emphasize that establishing general costs is not possible as each project is distinct and requires individual study and analysis.:Each project has unique characteristics, resulting in varying shapes of cost curves and break-even points. The outcomes of the feasibility evaluation play a crucial role in determining the extent to which the modular approach to construction is advantageous for the specific project at hand. The evaluation takes into consideration multiple factors to determine the potential benefits of adopting a modular construction approach, allowing decision-makers to make informed choices regarding the project's construction methodology

Mapping settlement extents at the annual time step has a wide variety of applications in demography, public health, sustainable development, and many other fields. Recently, while more multitemporal urban feature or human settlement datasets have become available, issues still exist in remotely-sensed imagery due to coverage, adverse atmospheric conditions, and expenses involved in producing such feature sets. These challenges make it difficult to increase temporal coverage while maintaining high fidelity in the spatial resolution. Here we demonstrate an interpolative and flexible modeling framework for producing annual built-settlement extents. We use a combined technique of random forest and spatio-temporal dasymetric modeling with open source subnational data to produce annual 100m x 100m resolution binary settlement maps in four test countries of varying environmental and developmental contexts for test periods of five-year gaps. We find that in the majority of years, across all study areas, the model correctly identified between 85-99% of pixels that transition to built-settlement. Additionally, with few exceptions, the model substantially out performed a model that gave every pixel equal chance of transitioning to the category “built” in each year. This modelling framework shows strong promise for filling gaps in cross-sectional urban feature datasets derived from remotely-sensed imagery, provide a base upon which to create future built/settlement extent projections, and further explore the relationships between built area and population dynamics.

Background: Adolescence is a developmental stage when there is a high risk of engaging in non-suicidal self-injury (NSSI). There is recent interest in the study of thwarted belongingness and perceived burdensome as variables associated with the frequency of NSSI in adolescents. Meaning in life (MIL) could be negatively associated with thwarted belongingness and perceived burdensome. To date, no studies have analyzed whether thwarted belongingness and perceived burdensomeness could be associated with the frequency of NSSI in adolescents. On the other hand, no studies have analyzed the buffering role of MIL in the association between thwarted belongingness and perceived burdensomeness and the frequency of NSSI. Aims: a) to test whether thwarted belongingness and perceived burdensomeness are associated with NSSI frequency; b) to test whether MIL moderates the association between thwarted belongingness and NSSI frequency; and c) to test whether MIL moderates the association between perceived burdensomeness and NSSI frequency. Method: The sample consisted of N = 1531 participants between 12 and 18 years old from Spain. The participants filled out the Inventory of Statements about Self-Injury, Purpose-In-Life Test-Adolescents Version, and Interpersonal Needs Questionnaire. Moderation analysis were performed. Results: Thwarted belongingness and perceived burdensomeness were positively associated with the frequency of NSSI in Spanish adolescents. MIL was a moderating variable between thwarted belongingness and the frequency of NSSI, and between perceived burdensomeness and the frequency of NSSI. Conclusion: Thwarted belongingness and perceived burdensomeness could be a risk factor for NSSI and MIL could be a protective factor against NSSI, and adding these variables to current descriptive theories of NSSI in adolescents would allow us to improve the assessment and treatment protocols for adolescents with NSSI.

Earth is a complex material with a mechanical and physical behavior that differs from modern building materials. The conservation of rammed earth (RE) constructions presents specific difficulties that are challenging to overcome. The lack of knowledge about RE due to its abandonment for decades and attempts to adopt materials and repair methodologies designed for new building products has led to inadequate interventions. In the case of historic defensive constructions, the doubts and technical difficulties are even greater due to the nature of the so called military RE (with physical and mechanical characteristics significantly different from those of civil, more common, RE) and, not least, due to the historical and cultural heritage value of these constructions. Some important interventions have been carried out recently and others are underway or in the planning stage, and there is a constant lack of information and technical data on the best ways to intervene. To fill this gap, the state of conservation of the RE defensive structures and the results of interventions carried out throughout history in the southwest of the Iberian Peninsula are being assessed. This article sets out the framework of the subject, identifies the material and construction techniques, and recognizes the main causes of its deterioration and decay. With special focus on the most frequent damages detected in historic military defensive structures built with RE, it analyses and discuss the most common techniques that have been used for the repair and conservation of these particular structures.

The main aim of this work is to compare and characterize the state of decay developed in a set of 14 monuments, including churches and Pazos (Galician traditional house) of the architectural heritage of the Barbanza Peninsula (Galicia), considering its relationship with the influence of the environmental factor. A macroscopic inspection was carried out to determine the deterioration patterns. The most reported pathology across the peninsula, due to the moisture regime, was the formation of dark areas (generally as biofilms) and the lichen growth (biological colonization). Depending on the proximity to the coast, the study area was divided into two zones. Zone 1, closer to the sea (&lt;1 km) with an important influence of sea salts and wind and zone 2, further from the sea with higher altitudes (center of the peninsula) and important rainfall, humidity and therefore, fauna growth. Crusts (to a lesser degree, because it is a mainly rural area) are more frequent in zone 1, but the state of conservation of stone is better than in zone 2 due to the concentration of urban centers that require aesthetics and constant maintenance. In zone 2, however, abandonment is greater and biological colonization (mainly by lichens and plants) is more developed along with deterioration patterns due to biological damage. The synergy of several factors such as salt, climatic conditions and spatial characteristics of the architectural heritage studied define the degree of deterioration of each heritage objective. The research has a potential contribution to the conservation measures to be undertaken.

Evolutionary psychology theories propose that contact with green, natural environments may benefit physical health, but little comparable evidence exists for brown, natural environments, such as the desert. In this study, we examined the association between “brownness” and “greenness” with fasting glucose among young residents of El Paso, Texas. We defined brownness as the surface not covered by vegetation or impervious land within Euclidian buffers around participants’ homes. Fasting glucose along with demographic and behavioral data was obtained from the Nurse Engagement and Wellness Study (N = 517). We found that residential proximity to brownness was not associated with fasting glucose when modeled independently. In contrast, we found that residential greenness was associated with decreased levels of fasting glucose, despite the relatively low levels of greenness within the predominantly desert environment of El Paso. A difference between the top and bottom greenness exposure quartiles within a 250 m buffer was associated with a 3.5 mg/dL decrease in fasting glucose levels (95% confidence interval: -6.2, -0.8). Our results suggest that within the understudied context of the desert, green vegetation may be health-promoting to a degree that is similar to other, non-desert locations in the world that have higher baselines levels of green.

Although significant efforts have been made to combat the spread of vector-borne diseases (VBDs), they still account for more than 17% of all infectious diseases. According to the World Health Organization (WHO), there were 216 million estimated cases in 2016, which is a 9.3% decrease from the estimated cases reported one decade earlier. It is known that the built environment, through features such as openings, can propagate the spread of malaria. There have been some significant efforts directed at addressing this risk. This notwithstanding, there are some knowledge gaps that have resulted in a missed opportunity for synergistically tackling the problem of vectors through leveraging design decisions made by built environment professionals. This work assesses the extent to which design decisions in the built environment can have a positive impact on the efforts directed at mitigating the risk of malaria based on selected cases from East Africa. Secondary data derived from relevant urban health journals as well as repositories curated by leading health agencies such as WHO were synthesized and analyzed using a web of causation approach. The outcome of the analysis is a schema of primary and secondary source (risk) factors. The use of the web of causation approach revealed the existing factor-to-factor interactions that could have a reinforcing effect. This information was used to identify the critical linkages and interdependencies across different factors. The outcome of the analysis was mapped against risk factors that can be linked to decisions made during the six primary phases of the construction life cycle: preliminary phase, conceptual design, detailed design, construction, facilities management, and end of life/disuse. The findings of the research have established that 1) there is, in fact, a built environment–related opportunity that can be leveraged to advance the impact of malaria mitigation effort; 2) cross-disciplinary synergies are critical to managing the interdependencies and complexity of malaria risk factors that have a reinforcing effect; and 3) a knowledge-management framework that serves as a decision support tool would be valuable for sharing data under a push-and-pull mechanism, in which data shared in real time can address the timeliness of mitigating the spread of malaria at the earliest stages for the greatest impact. Based on the findings, a conceptual architecture for a decision support framework has been proposed. This will be developed into a knowledge-management platform in subsequent efforts.

The Ames/quantitative structure-activity relationship (QSAR) International Challenge Projects held during 2014–2017 and 2020–2022, evaluated the performance of various predictive models. Despite the significant insights gained, the rules allowing participants to select prediction targets introduced ambiguity in model performance evaluation. This reanalysis identified the highest-performing prediction model, assuming a 100% coverage rate (COV) for all prediction target compounds and an estimated performance variation due to changes in COV. All models from both projects were evaluated using balance accuracy (BA), Matthews correlation coefficient (MCC), F1 Score (F1), and the first principal component (PC1). After normalizing the COV, a correlation analysis with these indicators was conducted, and the evaluation index for all prediction models in terms of the COV was estimated. In total, 109 models, the highest estimated BA (76.9) at 100% COV was MMI-VOTE1, reported by Meiji Pharmaceutical University (MPU). The best models for MCC, F1, and PC1 were all MMI-STK1, also reported by MPU. All models reported by MPU ranked in the top four. MMI-STK1 was estimated to have F1 scores of 59.2, 61.5, and 63.1 at COV levels of 90%, 60%, and 30%, respectively. These findings highlight the current state and potential of the Ames prediction technology.

This research aims to investigate the carbon fiber reinforced polymer (CFRP) when subjected to tensile, bending, and compression. Half of the specimens are also subjected to water to find out how water influences. The CFRP is created using a combination of carbon fiber layers and epoxy resin Bisphenol A Epichlorohydrin with hardener and is formed using the vacuum infusion method. From the water absorption test, it was found that the average weight gain of the specimens was 2.9% and the lowest value was at 0.6%, it was concluded that the increase in wet specimen weight was not too significant and water absorption tended to be slow. Mechanical testing ob-tained the highest average tensile stress, bending stress, compressive stress, and modulus of elasticity of 195 MPa, 295 MPa, 96 MPa, and 8914 MPa were from dry specimens while the lowest average values were 146 MPa, 286 MPa, 81 MPa, and 6160 MPa from wet specimens. The results of micro-photo observations on the tensile test fracture show that the specimen has a XGM fracture character with delamination and splitting fractures happening in multiple areas. In the bending test, the specimens experienced buckling fracture due to the fiber breaking and the inability of the matrix to withstand the additional stress. Shear fracture happened during the compressive test. In conclusion, water absorption has a bad impact towards the composite strength.

As a mediator variable, self-confidence is one of the most effective elements of the decision-making process of consumer behaviour. This research has studied the effects of different aspects of consuming fashion on the self-confidence and behaviour of consumers in Tehran’s clothing market. This study has considered the acceptance of new products, interest in mode and fashion, utilitarianism, and personal taste in its analysis. This research aims to understand the fashion buying behaviour amongst Iranian consumers in consideration of their attitude towards self-confidence and aspects of fashion consumption. The statistic sample is 400 consumers from Tehran’s clothing market who have been chosen based on the random availability procedure. The primary tool in this research was a questionary used to testify the assumptions and a model fit created by using structural equations and factor analysis. This research showed that the interest in mode and fashion, personal taste, utilitarianism, and new products positively impact self-confidence. In addition, the positive impact of self-confidence on fashion buying behaviour was confirmed.

The increasingly used approach of combining different simulation software in testing of automated driving systems (ADS) increases the need for potential and convenient software designs. Recently developed co-simulation platforms (CSP) provide the possibility to cover the high demand on testing kilometers for ADS by combining vehicle simulation software (VSS) with traffic flow simulation software (TFSS) environments. The emphasis on the demand of testing kilometers is not enough to choose a suitable CSP. The complexity level of the used vehicle, object, sensors and environment models is essential for valid and representative simulation results. Choosing a suitable CSP raises the question of how the test procedures should be defined and constructed and what the relevant test scenarios are. Parameters of the ADS, the environments, objects, sensors in VSS as well as traffic parameters in TFSS can be used to define and generate test scenarios. In order to generate a large number of scenarios in a systematic and automated way, suitable and appropriate software designs are required. In this paper we present a software design for CSP based on the Model-View-Controller (MVC) design pattern and implementation of a complex CSP for virtual testing of ADS. Based on this design, an implementation of a CSP is presented using the VSS from IPG Automotive called CarMaker and the TFSS from PTV Group called Vissim. The results have shown that the presented CSP design and the implementation of the co-simulation can be used to generate relevant scenarios for testing of ADS.

This work is concerned with the existence and uniqueness of boundary value problems defined on semi-infinite intervals. These kinds of problems seldom admit exactly known solutions and, therefore, the theoretical information on their well-posedness is essential before attempting to derive an approximate solution by analytical or numerical means. Our utmost contribution in this context is the definition of a numerical test for investigating the existence and uniqueness of solutions of boundary problems defined on semi-infinite intervals. The main result is given by a theorem relating the existence and uniqueness question to the number of real zeros of a function implicitly defined within the formulation of the iterative transformation method. As a consequence, we can investigate the existence and uniqueness of solutions by studying the behaviour of that function. Within such a context the numerical test is illustrated by two examples where we find meaningful numerical results.

This paper investigates the relationship between public spaces and quality of life (QoL) for older adults, aiming to identify knowledge gaps within the context of population ageing and urbanization. Recognizing the growing importance of sustainable urban development, the research explores how cities can foster active ageing and improve QoL through accessible and inclusive public spaces. A scoping literature review identifies five key QoL domains for older adults: autonomy, meaningful activities, positive social relationships, leisure opportunities, and health. The review highlights areas requiring further investigation, including the interplay between environmental design and social connections, intergenerational perspectives on public space liveliness, the influence of context on QoL and the built environment, and the value of qualitative research in this field. By contributing to the understanding of QoL in relation to public spaces through the lens of Person-Environment fit theory, this study aims to inform urban design, landscape architecture, and policymaking in the creation of age-friendly communities with inclusive public spaces.

As Arab countries are beginning to recover from the socioeconomic impacts of the COVID-19 pandemic, conservation programs are restarting. Noticeably, traditional conservation efforts have not helped improve the poor living conditions in most historic urban centers of Arab cities due to many reasons such as a lack of funds, urban management policies, and the narrow scope of conservation projects. In 2016, the UN urban agenda recognized tangible and intangible heritage as the basis for sustainable, vibrant, urban economies. These efforts reflect the new shift in conservation activities to tangible and intangible heritage and consider urban heritage a tourist product rather than antiquity. This approach grants urban vitality and sustainability for heritage areas. Thus, this study investigates the existing trends and forthcoming changes in conservation and their implication for the deteriorated historic urban city centers of the Arab world. International urban heritage conservation trends were highlighted, objectives and bases of successful urban conservation trends were reviewed, and an assessment framework was developed. Two case studies of historic centers in two Arab cities, Jeddah, and Aman, were empirically assessed using the developed framework. The findings highlight the most common urban problems of the historic centers in terms of urban management policies and trends. In addition, the impact of urban management policies on historic urban areas' sustainability, vitality, and quality was revealed. The paper ends with recommendations for conservation authorities to define a proposed framework to embed the conservation within the urban development plans for deteriorated historic urban centers. The paper's findings and recommendations can contribute to the required knowledge related to urban heritage conservation for practitioners and decision-makers.

Background: Few studies have assessed built environment correlates of active commuting in low-and-middle-income countries, but the different context could yield distinct findings. This cross-sectional study investigated associations between home neighbourhood environment characteristics and active commuting in Chennai, India. Methods: Adults (N = 370, 47.2% female, mean age = 37.9 years) were recruited from 155 wards in the metropolitan area of Chennai in southern India between January and June 2015. Participants self-reported their usual mode of commute to work, with responses recoded into three categories: (1) multi-modal or active commuting (walking and bicycling); (2) public transit; and (3) private transport. Environmental attributes around participants’ homes were assessed using the Neighborhood Environment Walkability Scale-India (NEWS-India). Associations between environmental characteristics and likelihood of active commuting and public transit use were modelled using logistic regression with private transport (driving alone or carpool) as the reference category, adjusting for age, gender, and household car ownership. Results: Consistent with other international studies, participants living in neighbourhoods with a mix of land-uses and a transit stop within a 10-minute walk from home were more likely to use active commuting (both p < 0.01). Land-use mix was significantly associated with the use of public transit compared to private transport (aOR = 5.2, p = 0.002). Contrary to findings in high-income countries, the odds of active commuting were reduced with improved safety from crime (aOR = 0.2, p = 0.003), aesthetics (aOR = 0.2, p = 0.05) and street connectivity (aOR = 0.2, p = 0.003). Conclusions: Different environmental attributes were associated with active commuting, suggesting that these relationships are complex and may distinctly differ from those in high-income countries. Unexpected inverse associations of perceived safety from crime and aesthetics with active commuting emphasize the need for high quality epidemiologic studies with greater context-specificity in the study of physical activity in LMICs. Findings have public health implications for India and suggest that caution should be taken when translating evidence across countries.

Background: Student-specific stress is pervasive and impairs health and attainment. Experimentally induced self-affirmation can reduce stress, but little is known about the mechanisms underlying this effect, and the role of individual differences. The present study explores the relationship between spontaneous self-affirmation, student-specific stress, and overlapping constructs of positive self-regard during the COVID-19 pandemic. Methods: The study investigated inter-relationships between spontaneous self-affirmation, student-specific perceived stress and potential covariates including self-esteem, self-integrity and habitual positive self-thought. University students (N = 151) aged 18 to 50 responded to an online questionnaire including the Spontaneous Self-Affirmation Measure, College Student Stress Scale, Rosenberg Self-Esteem Scale, Habitual Index of Positive Thinking and Self-Integrity Scale. Results: Unexpectedly, regression analysis revealed that spontaneous self-affirmation was a positive predictor of student-specific stress, seemingly driven by relational affirmations. Self-esteem and habitual self-thought were negative predictors of student-specific stress, whilst self-integrity was not a predictor. Conclusions: Habitual positive self-thought may offer a sustainable solution to student-specific stress, but spontaneous self-affirmation does not. A reduction in defensive responses, elicitation of negative emotions, or use of conditional relationships in relational affirmation

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

An extension of the models used to generate fractal traffic flows is presented by means of the formulation of a model that considers the use of one-dimensional chaotic maps. Based on the disaggregation of the temporal series generated by the model, a valid explanation of behavior of the values of Hurst exponent is proposed and the feasibility of their control from the parameters of the proposed model is shown.

This study discusses the experimental assessment of the in-plane mechanical behavior of a multi-leaf stone masonry wall built from cut stone and reinforced with metal connectors (cramps and dowels). The wall, inspired by conventional multi-leaf stone walls, is meant for use in modern stone masonry buildings. The wall is constructed from two parallel load-bearing walls with a cavity between them, which aims to conceal the installation and insulation needed in modern buildings. The load-bearing walls are connected with cramps and dowels at certain intervals so that the wall works as a single section against horizontal and vertical loads. To characterize the in-plane behavior of the proposed wall, compressive, triplet, and diagonal compression tests were conducted to investigate the compressive strength, shear strength, modulus of elasticity, stiffness, ductility, and energy absorption of the wall. Compared with dry and mortar joint walls, the use of dowels increased the initial shear capacity of the wall by 11 and 19 times, respectively. The application of cramps without curving channels inside the individual stone elements decreased the compressive strength by 18%. The energy absorption of the designed walls with metal connectors was substantially increased to that of the specimens representing conventional stone walls. The results obtained show the applicability of the wall due to its higher shear strength and minimal drop in compressive strength, which is within acceptable limits.

The construction of random fillings from the excavation of medium hardness rocks, with high particle sizes, presents limitations in compaction control. This research applies new control techniques with revised test procedures in the construction of the random fillings core, which constitutes the main part of the embankment, with the bigger volume and provides the geotechnical stability to the infrastructure. The maximum layer thickness researched was 800mm. As there are many types of rocks, this research is applied to metamorphic slates. Quality control has been carried out by applying new research associated with the revision of wheel impression test, topographic settlements and plate bearing test (PBT). A statistical analysis of the core of 16 slate random fillings has been carried out, with a total of 2250 in situ determination of density and moisture content, 75 wheel impression tests, 75 topographic settlement control and 75 PBT. The strong associations found between different tests have allowed to simplify the quality control.

In this paper I tentatively answer 50 questions sampled from a pool of over 10,000 weekly questions formulated by students in a course entitled “The Self”. The questions pertain to various key topics about self-processes, such as self-awareness, self-knowledge, self-regulation, self-talk, self-esteem, and self-regulation. The students’ weekly questions and their answers highlight what is currently know about the self. Answers to the student questions also allow for the identification of some recurrent lessons about the self. Some of these lessons include: all self-processes are interconnected (e.g., prospection depends on autobiography), self-terms must be properly defined (e.g., self-rumination and worry are not the same), inner speech plays an important role in self-processes, controversies are numerous (are animals self-aware?), measurement issues abound (e.g., self-reflection as an operationalization of self-awareness), deficits in some self-processes can have devastating effects (e.g., self-regulatory deficits may lead to financial problems), and there are lots of unknowns about the self (e.g., gender differences in Theory-of-Mind).

With the advent of digitization, the integration of advanced technologies in operations and projects across all sectors is in progress. Accordingly, efforts are being made to utilize cutting-edge technologies to improve the circularity of the built environment. This study aimed to review the existing applications and limitations of building information modeling (BIM) tools for circular economy (CE) implementation from this perspective. A literature review was conducted to provide an overview of the use of BIM tools for conducting life cycle assessments, energy analysis, waste management, and formulation of material passports for buildings. It was found that BIM tools, which are available across all life cycle phases of building, have a great potential to improve the circularity of the sector. The overview provided on the use of various BIM tools may help stakeholders of the built environment understand the role of BIM for CE adoption in the sector.

This paper focuses on the relationship between Mental Health and the Landscape. It aims to find out how people respond to Biophilic inspired landscape design in a healthcare setting. The focal point is not to cure diseases but to help them deal with the physiological, psychological, and psycho-social imbalance and provide a healing environment for the overall well-being of an individual. For this study, a Multispecialty Hospital was selected where an Indoor Healing Garden is used as a retrofitting tool to reduce stress and thus reconnect humans with nature. A multi-method approach is being used for this study. Initially, a questionnaire was conducted for the targeted users categorized into three types – patients, staff, and visitors to know their longing for the landscape. Based on this data and available literature, an evidence-based design was proposed. This conceptual design model is then shown to the targeted user and the response is recorded. The data has then collaborated with similar studies done earlier and design elements are highlighted which helps in creating a restorative environment by reducing stress and increasing recovery rate and thus approaching sustainable development.

The growing concern about climate change and the recognition of the planet’s limits led society to look for alternatives that promote the balance between the natural and the built environment. The circular economy emerges as an alternative to the linear economic model, inspired by natural metabolisms, by circulating resources in continuous loops, where their intrinsic value is maintained and improved. This research proposes a closed-loop strategy in the built environment by studying innovative constructive solutions that aim to find use, value, and inspiration in what is considered waste. A literature review is conducted on the circular design strategies, re-use and recycle typologies, and waste transformation processes. Then, the development of a methodology for qualitative evaluation and selection of re-used and upcycled construction materials from post-consumer waste and by-products is presented and then applied to thirty-five cases of constructive solutions from plastic, wood, paper, steel, aluminium, and agricultural waste. The research reports that the developed framework is adequate. The analysed alternative materials have good environmental performance and can be used as building materials despite their functional limitations, reflecting the enormous potential of waste as a resource for the construction industry.

Previous studies have mostly examined how sustainable cities try to promote non-motorized travel by creating a walking-friendly environment. Such existing studies provide little research that identifies how the built environment affects pedestrian volume in high-density areas. This paper presents a methodology that combines person correlation analysis, stepwise regression, and principal component analysis for exploring the internal correlation and potential impact of built environment variables. To study this relationship, cross-sectional data in the Melbourne central business district were selected. Pearson’s correlation coefficient confirmed that visible green index and intersection density were not correlated to pedestrian volume. The results from stepwise regression showed that land-use mix degree, public transit stop density, and employment density could be associated with pedestrian volume. Moreover, two principal components were extracted by factor analysis. The result of the first component yielded an internal correlation where land-use and amenities components were positively associated with the pedestrian volume. Component 2 presents parking facilities density, which negatively relates to the pedestrian volume. Based on the results, existing street problems and policy recommendations were put forward to suggest diversifying community service within walking distance, improving the service level of the public transit system, and restricting on-street parking in Melbourne.

Long-term, high-accuracy mapping of built-up land dynamics is essential for understanding urbanization and its consequences for the environment. Despite advances in remote sensing and classification algorithms, built-up land mapping using early satellite imagery (e.g., from the 2000s and earlier) remains prone to uncertainty. We mapped the extent of built-up land in the North China Plain, one of China’s most important agricultural regions, from 1990 to 2019 at three-year intervals. Using dense time-stack Landsat data, we applied discrete Fourier transformation to create temporal predictors and reduce mapping uncertainties for early years. We improved overall accuracy by 8% compared to using spectral and indices predictors alone. We implemented a temporal correction algorithm to remove inconsistent pixel classifications, further improving accuracy to a consistently high level (>94%) across years. A cross-product comparison showed that our study achieved the highest levels of accuracy across years. Total built-up land in the North China Plain increased from 37,941 km² in 1990–1992 to 131,578 km² in 2017–2019. Consistent, high-accuracy built-up land mapping provides a reliable basis for policy planning in one of the most rapidly urbanizing regions of the planet.

Advances in the availability of multitemporal and global built-/human-settlements datasets as derived from Remote Sensing (RS) can now provide globally consistent definitions of “human-settlement” at unprecedented spatial fineness. Yet, these data only provide a time-series of past extents and urban growth/expansion models have not had parallel advances at high-spatial resolution. We present a flexible modelling framework for producing annual built-settlement extents in the near future past last observed extents as provided by RS-based data. Using a random forest and autoregressive temporal models with short time-series of built-settlement extents and subnational level data, we predict annual 100m resolution binary settlement extents five years beyond the last observations. We applied this framework within varying contexts and predicted annual extents from 2010 to 2015. We found that our model framework preformed consistently across all sample countries and, when compared to time-specific imagery, demonstrated the capacity to capture human-settlement missed by the input time-series and validation extents. When comparing building footprints of small settlements to forecast extents, we saw that the modelling framework had a 12 percent increase in ground-truth accuracy. This framework shows promise for predicting near-future settlement extents, and provides a foundation for forecasts further into the future.

Evaluating mutation testing behavior can help decide whether refactoring successfully maintains the expected initial test results. Moreover, manually performing this analytical work is both time-consuming and prone to errors. This paper extends an approach to assess test code behavior and proposes a tool called MeteoR. This tool comprises an IDE plugin to detect issues that may arise during test code refactoring, reducing the effort required to perform evaluations. A preliminary assessment was conducted to validate the tool and ensure the proposed test code refactoring approach is adequate. By analyzing not only the mutation score but also the generated mutants in the pre- and post-refactoring process, results show that the approach is capable of checking whether the behavior of the mutants remains unchanged throughout the refactoring process. This proposal represents one more step toward the practice of test code refactoring. It can improve overall software quality, allowing developers and testers to safely refactor the test code in a scalable and automated way.

The multi-material design and the adaptability of a modern process chain require joining connections with specifically adjustable mechanical, thermal, chemical or electrical properties, whereby previous considerations have focused primarily on the mechanical properties. With clinching, the multitude of possible combinations of requirements, materials and component or joint geometry makes it impossible to determine these joint properties empirically. As a result of the established and empirically based procedure, no model exists to date that considers all questions of joinability, i.e. the materials (suitability for joining), the design (joining safety) and the production (joining possibility) and allows a calculation of the achievable properties. It is therefore necessary to describe the physical properties of the joint as a function of the three bonding mechanisms force closure, form closure and material closure in relation to the application. This approach enables the illustration of the relationships along the causal chain "joint requirement - binding mechanism - joining parameters". In this way the adaptability of the mechanical joining technology can be improved. A geometric comparison is made using metallographic cross sections, of clinched joints of the combination of aluminum and steel. The torsional testing of the rotationally symmetric clinching points for detection of the mechanical stress state are qualified as examination method and technological test. By measuring the electrical resistance in the base material, in the clinch joint and during the production cycle (after clinching, before precipitation hardening and after precipitation hardening), this change in the stress state can also be detected.

Simultaneous measurement of different substances from a single sample is an emerging issue to achieve efficient and high-throughput detection in several fields of application. Although immunoanalytical techniques have well-established and prevailing advantages over alternative screening analytical platforms, one of the incoming challenges for immunoassay is exactly multiplexing. The Lateral Flow Immunoassay (LFIA) is a leading immunoanalytical technique for onsite analysis thanks to its simplicity, rapidity and cost-effectiveness. Moreover, LFIA architecture is adaptable to multiplexing and therefore candidates as a possible answer to the pressing demand of multiplexing point-of-need analysis. The review present an overview of diverse approaches for multiplex LFIA, with a special focus on strategies based on new types of magnetic, fluorescent and colored labels

Vitrimers are covalent network materials, comparable in structure to classical thermosets. Unlike normal thermosets, they possess a chemical bond swap mechanism that makes their structure dynamic and suitable for activated welding and even autonomous self-healing. The central question in designing such materials is the trade-off between autonomy and material stability: The swap mechanism facilitates the healing but it also facilitates creep, which makes the perfectly stable self-healing solid a hard goal to reach. Here, we address this question for the case of self-healing vitrimers made from star polymers. Using coarse-grained molecular dynamics simulations, we study the adhesion of two vitrimer samples and find that they bond together on timescales that are much shorter than the stress relaxation time. We show that the swap mechanism allows the star polymers to diffuse through the material through coordinated swap events, but the healing process is much faster and does not depend on this mobility.

This paper critically reviews the correlation between the built environment and sociology as it pertains to residential segregation and social housing policy in Iran. The objective is to identify design strategies that minimize the risk of social isolation, promote social interaction, and foster a sense of community within affordable housing zones. The literature review includes existing research on urban segregation and social sustainability, with a focus on architectural solutions. Case studies are utilized to exemplify both positive and negative social outcomes related to urban segregation and identify effective design elements. The findings highlight the complex nature of residential segregation and its impact on social isolation, social capital, and social exclusion. The built environment contributes to the problem by facilitating the creation of isolated communities, and architects have a crucial role in addressing them. The results suggest that a comprehensive social housing policy is necessary to improve the quality of social housing and reduce residential segregation in Iran. Finally, the paper provides practical design strategies to promote social interaction, enhance accessibility and mobility, create mixed-use developments, and incorporate sustainable design features in social housing policy. By using design strategies that support social sustainability and inclusiveness, architects can create thriving and sustainable urban environments that prioritize the needs of marginalized communities.

In our increasingly urbanized world, precise and up-to-date maps of human settlements are essential for sustainable urban development policies. The availability of open-access Sentinel-2 data from the Copernicus program presents an opportunity to create a comprehensive global map of human settlements, offering a detailed view of built areas on a large scale. This study estimates large-scale built-up fractions using encoder-decoder deep learning architectures like U-net, Res-U-net, and Attention-U-net in the large and complex urban area of Delhi, India. Openly available datasets like Open Street Map (OSM) and Microsoft building footprint datasets are used to derive built-up fractions at 10×10m resolution cells for over 34,000 km2. Our results show that Attention-U-net with the Huber loss function performs the best in different built-up densities (i.e., urban, semi-urban or rural) with an R2 score of 0.631, while Res-U-net and U-net obtained an R2 score of 0.623 and 0.612, respectively. The investigated networks significantly improve the accuracy over the latest Global Human Settlement Layer product (GHSL-S2), which uses a deep-CNN and reaches an R2 of 0.387 in our case study area. The result of this study yields a valuable spatial layer for examining the spatial distribution of human settlements across the entire spectrum from rural to urban areas.

Design guidelines and the Design Review Panel (DRP) are crucial components in ensuring consistent and high-quality design within masterplan sites. This study focuses on New Zealand, examining the challenges faced by industry partners in adapting to masterplanned design guidelines. The case study centers on Hobsonville Point, the largest Government lead masterplan community in New Zealand, which promotes sustainable and higher-density living—an uncommon concept in the country. We conducted interviews with 18 key stakeholders involved in the development of Hobsonville Point. The results show that the DRP provides flexible judgments and insightful information that better accommodates individual development characteristics than the strict numerical standards specified in design guidelines. This study underscores the importance of DRP in producing good design outcomes, especially when they are involved at the very beginning of the design process. Additionally, we took note of stakeholder concerns about DRP members' expertise and the possible effects of high turnover rates on the design process. To strive for continual improvement, future empirical studies on the DRP process are encouraged to enhance proficiency and dependability. Design guidance should be prioritised to ensure climate-related design is implemented to promote sustainable urban development.

The Agile Building Adaptation (AgiBuild) framework is the adoption and adaptation of the large-scale agile framework for building adaptation projects. The agile methodology is proven to drive innovation by focusing on adaptation to change and user centricity. Similarly, the authors envision that the AgiBuild framework can fundamentally change the way that buildings are re-designed, refurbished, and operated. The AgiBuild framework is developed from the need of the building adaptation industry to manage uncertainties, overcome communication barriers, and improve innovation. In this study, a literature review of Agile and its impact on building adaptation projects is undertaken. Based on this systematic literature review, this paper defines the AgiBuilt framework and provides its benefits and barriers to implementation. A key finding of the literature review is that leadership influence, and adequate training form the key foundation for the implementation of the AgiBuild Framework. In defining the AgiBuild framework, the paper describes its components and how its implementation is likely to proceed. The authors propose that by adopting the AgiBuild framework, the industry can transform itself into a highly innovative and user-centred industry to improve productivity and performance of the construction industry..

Open campus policies that grant access to the off-campus food environment influence U.S. high school students’ exposure to unhealthy foods, yet predictors of these policies are unknown. Policy holding and built (walkability), food (access to grocery stores), social (school-to-neighborhood demographic similarity), and organizational (policy holding of neighboring schools) environment data were collected for 200 Oregon public high schools. These existing data derived from the Oregon School Board Association, WalkScore.com, 2010 Decennial Census, 2010-2014 American Community Survey, Supplemental Nutrition Assistance Program, TDLinex, Nielson directories, U.S. Department of Education, National Center for Education Statistics, and Common Core of Data. Most (67%) of Oregon public high schools had open campus policies. Logistic regression analyses modeled open campus policy holding as a function of built, food, social, and organizational environment influences. With health and policy implications, results indicate that schools’ walkability, food access, and extent of neighboring open campus policy-schools are significantly associated with open campus policy holding in Oregon.

Recently, several research groups have reported on anomalous enhancement of the self-field critical currents, Ic(sf,T), at low temperatures in superconductor/Dirac-cone material/superconductor (S/DCM/S) junctions. Some papers attributed the enhancement to the low-energy Andreev bound states arising from winding of the electronic wave function around DCM. In this paper, Ic(sf,T) in S/DCM/S junctions have been analyzed by two approaches: modified Ambegaokar-Baratoff and ballistic Titov-Beenakker models. It is shown that the ballistic model is an inadequate tool to analyze experimental data from S/DCM/S junctions. The primary mechanism for limiting superconducting current in S/DCM/S junctions is different from the conventional view that the latter is the maximum value within the order parameter phase variation. Thus, there is a need to develop a new model for self-field critical currents in S/DCM/S systems.

Although various atmospheric corrosion simulation models have been developed that give good results, industrial environments are still challenging. This paper aims to investigate the effect industrial atmospheres in Bor on the mechanical properties of structural steel S235JR and to create a constitutive model and also laboratory experimental conditions that will give the best results as an accelerated corrosion test. Atmospheric corrosion tests lasted six months, using sites close to the Electrolytic Refining Plant and Sulphuric Acid Plant, as well as air quality monitoring stations at a remote location in the city of Bor. The laboratory experiments included a salt chamber test lasting 120 h and 240 h and immersing the specimen in the electrolyte from the Electrolytic Refining Plant for 30 days. The results were compared with the standard specimens stored in the laboratory. The X-ray diffraction (XRD) method was used to identify the composition of corrosion products. The scanning electron microscopy (SEM) analysis was applied to analyze the fracture surfaces of the specimens. The use of the Complete Gurson Model (CGM) described the tensile characteristics of the corroded specimens. The study has shown that an enhanced acceleration model and conditions could be developed using numerical analysis of the test results.

The aim of the paper is to analyze the experimental results of the influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1000 °C and strain rates range 0.0018 - 0.1 s^-1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analyzed. Due to the dynamic recrystallization phenomenon present during the hot tensile tests, an increase in the flow stress is observed at the beginning of the deformation, after which it decreases until the fracture. By increasing the deformation temperature from 700 °C to 1000 °C, the tensile stress decreases significantly for all strain rates. The increase in the strain rate leads to the increase in the tensile stress. In compression tests by increasing the strain rate, the true strain is slightly increasing, but this depends on the temperature. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analyzed. Analysis by scanning electron microscopy showed the ductile behavior of the material. The degree of damage of the material caused by the presence of cavities increases by increasing the deformation temperature. For all the presented deformation conditions, the presence of the fracture through the ductile fracture mechanism was produced by the localized of necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behavior of 42CrMo4 steel can be improved.

Several articles have reported that the low number of COVID-19 cases in Japan is attributed to the small number of diagnostic RT-PCR tests performed. The criticism is based on the low number of the tests performed, and they suspected there would be more potential cases in Japan. The use of pre-test probability among tested subjects is proposed in order to evaluate of the sufficiency of test availability instead of the number of the tests. The pre-test probability means the average probability, i.e., ‘suspicion level’, of having coronavirus among the tested subject in a country. The higher pre-test probability is regarded as less sufficient opportunity of the tests, and the test availability could be evaluated by the pre-test probability. Thus, potential problems of underestimation of COVID-19 cases by insufficient amount of the test would be clear by using pre-test probability. The comparison of the pre-test probability could be replaced with that of the positive rate of the test because of the linear relationship between them under the assumption of common sensitivity and specificity. Japan shows the third lowest rate (8.6%), and is considered that the considerably sufficient number of the tests have been performed. In conclusion, the positive rate of the test as a surrogate index of the pre-test probability is useful to evaluate the sufficiency of test amount instead of the number of the tests performed. In present, the potential problem of underestimation by insufficient test availability would be less serious in Japan.

The Combined Elevation Test (CET) is a musculoskeletal screening technique (MST) replicates the streamline position in swimming and is commonly used in various sports. Although the CET is widely used, no normative data exist within an adolescent population. Therefore, the purpose of this study was to develop a normative data set for the CET within an adolescent population and to evaluate the influence various demographic and anthropometric variables. Data was collected for 416 participants aged between 8 and 18 years old. Age and arm span showed a significant correlation with CET scores (arm span r_s (105) = .478, p = .000, age r_s (416) = .238 p = .000). Regression analysis further quantified the influence of arm span and age on CET scores accounting for 23.1% and 5.3% of variability respectively. These results can be used as a reference point for clinicians and coaches who are using the CET within their assessment.

Self-assembly is a spontaneous process through which macroscopic structures are formed from basic microscopic constituents (e.g. molecules or colloids). By contrast, the formation of large biological molecules inside the cell (such as proteins or nucleic acids) is a process more akin to self-organization than to self-assembly, as it requires a constant supply of external energy. Recent studies have tried to merge self-assembly with self-organization by analyzing the assembly of self-propelled (or active) colloid-like particles whose motion is driven by a permanent source of energy. Here we present evidence that points to the fact that self-propulsion considerably enhances the assembly of polymers: self-propelled molecules are found to assemble into polymer-like structures, the average length of which increases towards a maximum as the self-propulsion force increases. Beyond this maximum, the average polymer length decreases due to the competition between bonding energy and disruptive forces that result from collisions. The assembly of active molecules might have promoted the formation of large pre-biotic polymers that could be the precursors of the informational polymers we observe nowadays.

(1) Background: Cardiorespiratory fitness (CRF) is a prognostic factor regarding long time morbidity and mortality. To assess CRF the well-known gold standard is cardiopulmonary exercise testing (CPET), which is a time consuming and expensive test. Therefore, alternative methods for routine evaluation of CRF are needed for the general population as well as for specific patient groups such as children and young adults with congenital heart disease. The Stair Climbing Test (SCT) is a simple and resource saving test reported in the current literature. This test is used in various settings to assess different health associated risk factors including cardiorespiratory fitness, muscular resilience, therapy effectiveness or pre- and postoperative morbidity and mortality.

The papaya mealybug Paracoccus marginatus is an invasive, polyphagous pest and poses a quarantine threat to tropical and subtropical countries. Infested commodity internationally should be undergoing phytosanitary treatment, while irradiation is recommended to replace methyl bromide fumigation. Dose-response tests were conducted on the 2-, 4-, and 6-d-old eggs and gravid females of P. marginatus using the X-ray radiation doses of 15–105 Gy with an interval of 15 Gy, respectively. Radiotolerance was compared using fiducial overlapping and lethal dose ratio (LDR) test, resulting in insignificant difference except for LDR test at LD90 (leading 90% mortality at 95% confidence level (CL)); the estimated dose for 99.9968% mortality at 95% CL was 176.5–185.2 Gy, which was validated in the confirmatory tests using gamma irradiation because gammy and X-rays have equal biological effect on pests. Therefore, a total of estimating 60,386 gravid females of papaya mealybug irradiated with 146.8–185.0 Gy resulted in no F1 nymphs developing. Eggs can therefore be used as an alternative to gravid females for dose-response tests; the recommended minimum dose for phytosanitary treatment of P. marginatus on infested commodity is 185 Gy, with treatment efficacy ≥ 99.9950% at 95% CL.

Due to species barriers and poor adaptability to new host environments, few pathogens cause global pandemics. But, SARS-CoV-2 is one exception with its high transmissivity and delayed onset of symptoms. Fortunately, the world was able to tap on the technologies especially the maturing RT-qPCR designed to combat SARS to launch an initial offensive on SARS-CoV-2. These initial efforts may have bought time for scientists to develop more refined diagnostic tests that specifically target SARS-CoV-2. This article describes the effort put forth by the biotech industry and academia in Singapore to develop diagnostic tests that aid the early detection of positive cases, and thereby help contain the virus. Direct tests such as RT-qPCR and antigen rapid test profile the virus nucleic acid and surface proteins, respectively. But, of equal importance in case detection and treatment is serological tests that measure the relative abundance of IgM and IgG which is indicative of infection phase and quality of immune response in positive cases. Other tests such as isothermal amplification, CRISPR-based diagnostics and breath tests are also in development or at initial field deployment, and would undoubtedly provide valuable use experience useful for the development of molecular assays to detect and combat the next pathogen of global concern.

In the context of the COVID-19 Pandemic, the use of surgical masks has become the new normal. The use of these devices in exercise and medical situations has been advocated with the purpose of reducing contagions, but some concerns exist regarding its safety. We performed maximal treadmill stress tests in 12 healthy young subjects, with and without surgical mask use, and measured exercise capacity, oxygen saturation (rest, peak exercise and post-exercise) and electrocardiographic changes. Exercise capacity and Oxygen saturation levels decreased in peak exercise vs rest in a statistically significant manner when mask was used. ECG changes, although not significant, were present in 3 subjects when mask was used and disappeared when the test was made unmasked. We conclude that masked exercise has the potential to cause decreased exercise load and oxygen saturation and potentially cause diagnostic errors in medical exams.

Keywords: Demographics, Diversity, Gender, Race, Age, Professionals, Built Environment, Construction Industry, South Africa

The study purpose was to train and validate a deep-learning approach to detect micro-scale streetscape features related to pedestrian physical activity. This work innovates by combining computer vision techniques with Google Street View (GSV) images to overcome impediments to conducting audits (e.g., time, safety, and expert labor cost). The EfficientNETB5 architecture was used to build deep-learning models for eight micro-scale features guided by the Microscale Audit of Pedestrian Streetscapes-Mini tool: sidewalks, sidewalk buffers, curb cuts, zebra and line crosswalks, walk signals, bike symbols, and streetlights. We used a train--correct loop, whereby images were trained on a training dataset, evaluated using a separate validation dataset, and trained further until acceptable performance metrics were achieved. Further, we used trained models to audit participant (N=512) neighborhoods in the WalkIT Arizona trial. Correlations were explored between micro-scale features and GIS-measured- and participant reported-macro-scale walkability. Classifier precision, recall, and overall accuracy were all >84%. Total micro-scale was associated with overall macro-scale walkability (r=0.300,p<.001). Positive associations were found between model-detected and self-reported sidewalks (r=0.41,p<.001) and sidewalk buffers (r=0.26,p<.001). Computer vision model results suggest an alternative to trained human raters, allowing for audits of hundreds or thousands of neighborhoods for population surveillance or hypothesis testing.

Leisure-time physical activity (LTPA) is associated with access and use of public open spaces. The “President João Goulart Elevated Avenue” and current denominated “Minhocão” is a facility for leisure activities that are open for people during the night/weekends. The aim of this study was to examine if the prevalence of LTPA among individuals living in the surroundings of Minhocão is different according to proximity to, and use of, the facility. We conducted a cross-sectional study with cluster sampling with people aged ≥18 years who lived in households until 500m and between 501m to 1500m of Minhocão. The survey was conducted between December/2017 until March/2019 with an electronic questionnaire self-responded. We conducted bivariate analysis and Poisson regression to examine possible differences in LTPA according to the proximity of residences and use of Minhocão. The analysis used post-stratification weights. A total of 12,030 telephone numbers of people were drawn (≤500m = 6,942; and &gt;500m to ≤1500m = 5,088). The final sample analyzed were of 235 residents who returned the questionnaires. There was a higher prevalence of individuals engaging in at least 150 minutes per week of LTPA among users than non-users (Prevalence Ratio=2.23, IC95%1.72-2.90). People who used the park had higher prevalence of all types of LTPA than non-users. The results can serve to inform government decision-making on the future of Minhocão.

With the development of the city, a large number of water networks in the built-up areas of Bangkok have been filled and hardened, resulting in poor urban flooding and aggravating flooding, causing loss of life and property of citizens. In this paper, on the basis of combing the current water networks and open space potential flood storage points in the built-up areas of Bangkok, the complex network diagram of the water system in the built-up areas of Bangkok is constructed by combining the theory of complex networks and analyzing the attribute parameters of the network and the characteristic parameters of the open space storage nodes and water system paths, and finding that the water system network in the built-up area of Bangkok has complex network characteristics such as robustness, clustering and hierarchy. By exploring the key storage points and water system connection paths, the researchers initially constructed a flood safety pattern in the built-up area of Bangkok with 145 key nodes and 127 river paths as the backbone, and conceptualized the development study of the flood safety pattern in both horizontal and vertical directions. The urban flood safety pattern based on complex network theory proposed in this paper provides a case reference and methodological ideas to scientifically solve the game conflict between the demand for construction land for urban development and the construction area of urban open space storage points and water storage network under the increasingly severe flooding situation.

Shelter-in-place aimed at slowing COVID-19 transmission has altered nature accessibility patterns, creating quasi-experimental conditions to assess if retracted nature contact and perceived nature deprivation influences physical and emotional wellbeing. We measure through survey methods how pandemic mandates limiting personal movement and outdoor nature access effect self-assessed nature exposure, perceived nature deprivation, and subsequent flourishing as measured by the Harvard Flourishing Index. Results indicate that perceived nature deprivation strongly associates with neighborhood nature contact, time in nature and access to municipal nature during the pandemic, after controlling for shelter-in-place mandates, job status, household composition, and sociodemographic variables. Our hypothesis that individuals with strong perceived nature deprivation under COVID-19 leads to diminished wellbeing proved true. Interaction models of flourishing showed positive modification of nature affinity with age and qualitative modification of nature deprivation with race. Our results demonstrate the potential of local nature contact to support individual wellbeing in a background context of emotional distress and social isolation, important in guiding public health policies beyond pandemics.

With the rapid spread of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) that results in coronavirus disease 2019 (COVID-19), corporate entities, federal, state, county and city governments, universities, school districts, places of worship, prisons, health care facilities, assisted living organizations, daycares, homeowners, and other building owners and occupants have an opportunity to reduce the potential for transmission through built environment (BE) mediated pathways. Over the last decade, substantial research into the presence, abundance, diversity, function, and transmission of microbes in the BE has taken place and revealed common pathogen exchange pathways and mechanisms. In this paper, we synthesize this microbiology of the BE research and the known information about SARS-CoV-2 to provide actionable and achievable guidance to BE decision makers, building operators, and all indoor occupants attempting to minimize infectious disease transmission through environmentally mediated pathways. We believe this information is useful to corporate and public administrators and individuals responsible for building operations and environmental services in their decision-making process about the degree and duration of social-distancing measures during viral epidemics and pandemics.

Aedes aegypti mosquitoes are primary vectors of dengue, yellow fever, chikungunya and Zika viruses. Ae. aegypti is highly anthropophilic and relies nearly exclusively on human blood meals and habitats for reproduction. Socioeconomic factors may influence the spread of Ae. aegypti due to its close relationship with humans. This paper describes and summarizes the published literature on how socioeconomic variables influence the distribution of Ae. aegypti mosquitoes in the mainland United States. A comprehensive search of PubMed/Medline, Scopus, Web of Science, and EBSCO Academic Search Complete through June 12, 2019 was used to retrieve all articles published in English on the association of socioeconomic factors and the distribution of Ae. aegypti mosquitoes. Additionally, a hand search of mosquito control association websites was conducted in an attempt to identify relevant grey literature. Articles were screened for eligibility using the process described in the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. Initially, 3,493 articles were identified through the database searches and previously known literature. After checking for duplicates, 2,145 articles remained. 570 additional records were identified through the grey literature search for a total of 2,715 articles. These articles were screened for eligibility using their titles and abstracts, and 2,677 articles were excluded for not meeting the eligibility criteria. Finally, the full text for each of the remaining articles (n = 38) was read to determine eligibility. Through this screening process, 11 articles were identified for inclusion in this review. The findings for these 11 studies revealed inconsistent relationships between the studied socioeconomic factors and the distribution and abundance of Ae. aegypti. The findings of this review suggest a gap in the literature and understanding of the influence of anthropogenic factors on the distribution of Ae. aegypti that could hinder efforts to implement effective public health prevention and control strategies should a disease outbreak occur.

We report on the field testing datasets and performance evaluation results obtained from a commercial property-based visually-clear solar window installation site in Perth-Australia. This installation was fitted into a refurbished shopping centre entrance porch, and showcases the potential of glass curtain wall-based solar energy harvesting in built environments. In particular, we focus on photovoltaic (PV) performance characteristics such as the electric power output, specific yield, day-to-day consistency of peak output power, and the amounts of energy generated and stored daily. The dependencies of the generated electric power and stored energy on multiple environmental and geometric parameters are also studied. An overview of the current and future application potential of high-transparency, visually-clear solar window-based curtain wall installations suitable for practical building integration is provided.

Can ‘restoration and therapy in design’ signify something more than the places like hospitals and healing gardens? Can those restorative environments be brought inside the working and living environments to mitigate the psychological problem at the source? The main objective of this paper is to look at the strategies and developments of Biophilic design with respect to therapy and restoration in order to achieve sustainability in terms of quality of life within the immediate built-environment. The paper explores the mental health issues under the domains of built-environment and indoor environment with respect to their connection with nature. Biophilic design has gained a favourable momentum within the last four decades and is now visualised as a medium that bridges the gap between humans and the nature. Out of a variety of measures of sustainable environmental design, biophilic design focuses on the end-results of naturally nurtured or inspired habitats and workplaces. It embodies strategies of Green and Intelligent buildings, works as a mitigation strategy for foul indoor environment and establishes the vision that veristic sustainability can only be achieved if there is qualitative control over human physiological prosperity and psychological health. In context of work efficiency, preference and productivity within the indoor environment, it is seen as a promoter of constructive thoughts and enhancer of creativity. The paper aims to enlist biophilic design and retrofitting strategies, which can improve cognitive function, reduce stress and provide mental peace within the built environment.

In this paper we describe many important aspects connected with lubricants, namely: the most cheapest organic lubricant in the word, how effectively save lubricant between pairs of friction, what kind of rational shapes for the lubricant must be, what it will be connected with wear and tear using the new organic lubricant (for this purpose formulas and curves are shown in computer program MathCad with calculation). Moreover, there is one physical model which helps to catch car exhausted gases. In conclusion, some recommendations will be given to realize them into the practice during the operation for the different mechanisms including ecology.

In this paper, I propose a test for machine self-awareness inspired by the Turing test. While my test is plain and simple, it offers a much-needed alternative to ungrounded speculation while still capturing the essence of self-awareness. I discuss how to apply the test to Large Language Models and conduct experiments on GPT-3.5 that suggest it is not self-aware. I discuss the implications of machine self-awareness and relate it to questions about meaning and understanding. Finally, I present some next steps for studying self-awareness in machines.

The present paper reports an exact approach quantifying the electromagnetic contribution to the anomalous magnetic moment occurring in isolated system comprised of non-composite particle carrying elementary electric charge. Essential averaging procedure and regularization of the electromagnetic field potentials necessary when quantifying the electromagnetic self-interactions and when deriving equations of motion without singularities and obeying the conservation laws are thoroughly discussed. The study shows that the dynamics of the considered system is associated to unique classical transcendental equations of motion satisfied by the particle's velocity and the electromagnetic contribution to the anomalous $g$-factor known from the quantum electrodynamics. The equations of motion lead to an exact analytical expression for the anomalous $g$-factor that provides more accurate result than that calculated with the aid of quantum electrodynamics. It matches the experimentally measured value reported in the literature to a one part per trillion. We obtain a_e=0.00115965218000(65) thus reveling the potential of non-perturbative, non-probability methods in predicting the electron's anomalous g-factor.

Background: The adoption of self-care behaviors among patients with arterial hypertension (AH) plays an important role in the management of their health condition. However, a lack of scales assessing self-care is observed. We aimed to develop and validate the Hippocratic hypertension self-care scale. Methods: From a pool of questions derived from a literature review, 18 items were included in the scale and reviewed by a committee of experts. Participants indicate the frequency at which they follow the self-behavior prescribed in each statement on a five-point Likert scale. Data were collected between April 2019 and December 2019. Re-sults: 202 consecutive adult patients with AH were enrolled in the study. The internal consistency of the scale was found to be 0.807, using Cronbach’s alpha coefficient. An exploratory factor analysis identified two do-mains that accounted for 92.94% of the variance of the scale items; however, each sub-scale could not be used as an independent scale. Finally, the test- retest of the scale showed a significant strong correlation (r=0.0095, p<0.001). Conclusion: Our data indicate that the scale is a reliable and valid tool for assessing self-behaviors in patients with AH. Health professionals can use it in their clinical practice to improve the management of patients’ health condition.

: BACKGROUND: The prevalence of smoking among students is a growing concern, particular-ly among medical students. Being associated with stress, competitiveness, and various social in-fluences, smoking can have detrimental effects on self-esteem and self-efficacy and may create a vicious cycle that may contribute to students’ well-being and academic performance out-comes.METHODS: A cross-sectional study on 456 medical students was conducted via an online survey using structured questionnaires on socio-demographic characteristics, smoking habits, nicotine dependence, self-esteem, and self-efficacy. RESULTS: The prevalence of smoking was 31.1% The scores of self-esteem and self-efficacy were positively correlated with smoking habits (W1=0.957, W2=0.975, P<0.05). Students presented rather low smoking addiction with male stu-dents having slightly higher scores than female students on self-esteem and self-efficacy, mili-tary students had higher self-esteem scores than civilians with physical activity having a posi-tive correlation with non-smoking behavior. CONCLUSION: According to our results, self-esteem and self-efficacy were slightly positively correlated with smoking habits. Furthermore, there was no statistically significant association between other social factors and smoking. Our results may develop a theoretical basis for medical students’ psychological variables studying for further implementation of university educational programs and preventive interventions em-powering students towards an overall better quality of life, addressing, among others, smoking behaviors.

Self-enhancement (SE) is often overlooked as a fundamental cognitive ability mediated via the Pre-Frontal Cortex (PFC). Here we present research that establishes the relationship between the PFC, SE, and the potential evolved beneficial mechanisms. Specifically, we believe there is now enough evidence to speculate that SE exists to provide significant benefits and should be considered a normal aspect of the self. Whatever the metabolic or social cost, the upside of SE is great enough that it is a core and fundamental psychological construct. Furthermore, though entirely theoretical, we suggest that a critical reason the PFC has evolved so significantly in Homo sapien is to, in part, sustain SE. We therefore elaborate as to its proximate and ultimate mechanisms.

While the desire to uncover the neural correlates of consciousness has taken numerous directions, self-face recognition has been a constant in attempts to isolate aspects of self-awareness. The neuroimaging revolution of the 1990’s bought about systematic attempts to isolate the underlying neural basis self-face recognition. These studies, including some of the first fMRI (functional Magnetic Resonance Imaging) studies, revealed a right hemisphere bias for self-face recognition in a diverse set of regions including the insula, the Dorsal Frontal Lobe, the Temporal Parietal Junction and Medial Temporal Cortex. Confirmation of these data (which are correlational) was provided by TMS (Transcranial Magnetic Stimulation) and patients in which direct inhibition or ablation of right hemisphere regions leads to a disruption or absence of self-face recognition. These data are consistent with a number of theories including a right hemisphere dominance for self-awareness and/or a right hemisphere specialization for identifying significant social relationships including to oneself.

The characteristics of response to stressful situations depend on a complex of factors such as personality traits, emotional regulation, health state, features of the nervous system, motor functions and proprioception. In cases of disruption of the brain's dopamine system due to disease or chemotherapy, hormone discharge due to stress, changes in emotions and proprioception may occur. The aim of our study was to find the relationship of stress resilence in verbal test and individual differences performed in proprioceptive test in onco-patients, sportsmen and group of control; as well as to observe the differences between these groups in the verbal stress resistance and individual differences proprioceptive tests. The results showed that onco-patients were less resistant as per verbal stress resistance outcomes for a major part of variables compared to other groups. The sportsmen were superior in verbal Risk and Control dimensions compared to other groups; but less in Positive Affectiveness. The proprioceptive test perfomance revealed the only statistically significant difference in performance in the dimension related to Mood, showing more Pessimism in the sportsmen group, but more Optimism in the oncopatients at temperamental (or intrisinc) level. The obtained results can be used by psychologists, therapists, coach and healthcare when needed to attend the specific needs of public, being pateints or sportsmen, etc.

Various therapeutic approaches have been developed for neglect. Many studies have demonstrated the effect of Digital therapeutics(DTx) on neglect. By contrast, only a few studies have reported on the effects of DTx on egocentric and allocentric neglect. In this article, seven studies on DTx of egocentric and allocentric neglect were reviewed. DTx, which was employed in these studies, could be classified as follows: 1) software adaptation in traditional treatment, 2) VR game using the head-mount display as treatment, and 3) development of new digital program like ReMoVES. In addition, more studies and effective results were reported on egocentric neglect than allocentric neglect. In future studies, each effect on egocentric and allocentric neglect should be identified in detail through the appropriate use of differential evaluation and long-term application of independent digital therapeutics.

The importance of statistics in biological research is inevitable. The appliance of statistics is the most powerful tool to support the scientific hypothesis and to give credibility to biological research methodology, to interpret convoluted explanations and conclusions based on the research findings. The evidences from literatures point the persistent statistical errors, selection of non-proper statistical test with the consequence of misinterpretation of the scientific results which are published in international journals. One of the most extensively used statistical tests in the field of biology (preclinical and clinical) is analysis of variance (ANOVA). ANOVA test is in place of multiple T-tests to compare the means of more than two groups at a time; and there are some important points which biologists should be aware of them to avoid possible misinterpretation of results with the consequence of wrong conclusion. Accordingly, the aim of the current review is to help biologists to understand the basic concepts of ANOVA test and reach to a more valid interpretation of achieved results.

Objectives: This paper presents a statistical review of modelling simulations for frequency and sensitivity of COVID-19 testing paradigms. Methods: We performed a review of preprints and published articles on PubMed from January 1, 2020 – March 1, 2021 using the search terms “COVID screening testing”, “COVID testing frequency”, “COVID testing frequency screening” and “SARS-CoV-2 testing frequency”.Results: Several authors’ conclusions support the claim that test frequency and test sensitivity both play a role in reducing SARS-CoV-2 transmission. We highlight the interplay between frequency of testing, test sensitivity and the speed at which test results are available in our review. Conclusions: Evidence suggests that sensitivity and frequency of testing both play a part in decreasing transmission of disease. We conclude that, overall, test sensitivity plays less of a role in reducing disease transmission in a population compared to the frequency of testing and how quickly test results are available.

This paper presents results from numerical and experimental investigation on Charpy tests in order to point out failure mechanisms and to evaluate new polymeric blends PP+PA6+EPDM. Charpy tests were done for initial velocity of the impactor of 0.96 m/s and its mass of 3.219 kg and these data were also introduced in the finite element model. The proposed model take into account the system of four balls, including support and the ring of fixing the three balls and it has a finer discretization of the impact area to highlight the mechanisms of failure and their development in time. The constitutive models for four materials (polypropylene with 1% Kritilen, two blends PP+PA6+EPDM and a blend PA6+EPDM) were derived from tensile tests. Running simulations for each constitutive model of material makes possible to differentiate the destruction mechanisms according to the material introduced in the simulation, including the initiation and the development of the crack(s), based on equivalent plastic strain at break (EPS) for each material. The validation of the model and the simulation results was done qualitatively, analysing the shape of broken surfaces and comparing them to SEM images and quantitatively by comparing the impact duration, energy absorbed by the sample, the value of maximum force during impact. The duration of the destruction of the specimen is longer than the actual one, explainable by the fact that the material model does not take into account the influence of the material deformation speed in Charpy test, the model being designed with the help of tests done at 0.016 m/s (1000 mm/min) (maximum strain rate for the tensile tests). Experimental results are encouraging for recommending the blends 20% PP+42% PA6+28% EPDM and 60% PA6+ 40%EPDM as materials for impact protection at low velocity (1m/s). Simulation results are closer to the experimental ones for the more brittle tested materials (with less content of PA6 and EPDM) and more distanced for the more ductile materials (with higher content of PA6 and EPDM).

Alcohol and substance addiction is a type of brain disease that damages many areas of life of the individual and has psychological components. Since questioning alcohol use alone is not sufficient in the diagnostic evaluation process, self-awareness and the individual's long-term psychological well-being are important in the rehabilitation process. Since investigating alcohol use alone is not sufficient in the diagnostic evaluation process, self-awareness and the individual’s long-term psychological well-being are important in the rehabilitation process. Primary prevention is used to prevent disease in healthy people, and secondary prevention is used for early diagnosis to people at risk. Tertiary prevention is important to prevent recurrence of the disease in the treated person. In addiction, which is a chronic problem, a need has emerged for tertiary prevention, that is, rehabilitation standards. If people are uncertain about the harm perception and the natural result of their behavior, they easily slip into the substance. Therefore, as a positive psychotherapy technique, harm perception and result awareness levels should be clarified. For this reason, scales were developed. The inclusion of new psychology perspectives and therapy techniques, such as positive psychology, in the treatment process requires setting new standards. In this study, it was aimed to develop result awareness and harm perception scales to determine the awareness levels and rehabilitation standards of alcohol and substance addicted individuals, and to compare awareness in normal and addicted groups. The study group consisted of 1134 participants, 41 of whom were addicts. Among the two scales developed in the study, the Uskudar Result Awareness Scale (USRAS) consisting of 25 items and 6 factor, explained 58.4% of the total variance. The Uskudar Harm Perception Scale (USHPS), consisting of 36 items and 10 factors, explained 56.3% of the total variance. Confirmatory factor analysis of the two scales resulted in acceptable goodness-of-fit values. (X2/df<3; RMSEA<.08; NFI>.90; NNFI>.95; CFI>.95; GFI>.90; AGFI>.85). In the comparisons made, the result awareness of the normal group was moderate (X=3,81); whereas the addicted group had a low result awareness (X=3,20); The effect size of the difference between the two groups was found to be high (d=1,45; >0,8). In the other measure, the harm perception of the normal group was found in the low-risk group (X=3,78); the harm perception of the addicted group was found in the moderate-risk group (X=3,43). According to Cohen d calculations, the effect size of the difference between the two groups is high (d=1,43; >0,8). It has been concluded that the two scales that emerged in the research are valid and safe, can be included in the rehabilitation studies and the creation of self-awareness, and their effectiveness should be tested.

Objective: This study assessed hearing aid benefits for people with a normal audiogram but hearing-in-noise problems in everyday listening situations. Design: Exploratory double-blinded case control study whereby participants completed retrospective questionnaires, ecological momentary assessments, speech-in-noise testing, and mental effort testing with and without hearing aids. Twenty-seven adults reporting speech-in-noise problems but normal air-conduction pure-tone audiometry took part in the study. They were randomly separated into an experimental group who trialled mild-gain hearing aids with advanced directional processing and a control group fitted with hearing aids with no gain or directionality. Results: Self-reports showed mild-gain hearing aids reduce hearing-in-noise difficulties and provide a better hearing experience (i.e., improved understanding, participation, and mood). Despite the self-reported benefits, the laboratory tests did not reveal a benefit from the mild-gain hearing aids, with no group differences on speech-in-noise tests or mental effort measures. Further, participants found the elevated cost of hearing aids to be a barrier for their adoption. Conclusions: Hearing aids benefit the listening experience in some listening situations for people with normal audiogram who report hearing difficulties in noise. Decreasing the price of hearing aids may lead to greater accessibility to those seeking remediation for their communication needs.

The progress in markerless technologies is bringing clinicians tools to rapidly evaluate tests such as Timed Up and Go (TUG) without compromising the time of the assessment, yet it raises questions about the potential trade-off in accuracy compared to traditional marker-based systems, suggesting that the precision of these evaluations is not yet conclusively established. The OpenCap system is an easy tool to process 3D kinematics with two iPhone cameras placed in front of the subject. Previous research has primarily focused on walking and movement towards the cameras with the subject facing the cameras (WF) and thus has been unable to disentangle the differences in the movement directions. We have compared the OpenCap system with a standard marker-based system for both walking directions. In OpenCap, we found significantly worse results capturing walking facing away from the cameras (RW). Compared to the marker-based system, our findings indicate troubles measuring kinematic parameters but provide good accuracy in measuring spatial-temporal parameters. These insights pave the way for refining markerless assessment technologies, potentially enhancing their utility in clinical settings.

Rubble stone masonry walls are widely diffused in most of the cultural and architectural heritage of historical cities. The mechanical response of such material is rather complicated to predict due to their composite nature. Vertical compression tests, diagonal compression tests, and shear-compression tests are usually adopted to experimentally investigate the mechanical properties of stone masonries. However, further tests are needed for the safety assessment of these ancient structures. Since the relation between normal and shear stresses plays a major role in the shear behavior of masonry joints, governing the failure mode, triplet test configuration was here investigated. First, the experimental tests carried out at the laboratory (LPMS) of the University of L'Aquila on stone masonry specimens were presented. Then, the triplet test was simulated by using the Total Strain Crack Model, which reflects all the ultimate states of quasi-brittle material such as cracking, crushing and shear failure. The goal of the numerical investigation was to evaluate the shear mechanical parameters of the masonry sample, including strength, dilatancy, normal and shear deformations. Furthermore, the effect of (i) confinement pressure and (ii) bond behavior at the sample-plates interfaces were investigated, showing that they can strongly influence the mechanical response of the walls.

Signal-to-noise ratio (SNR) is an important index to evaluate radiation performance and image quality of optical imaging systems under low illumination background. Under the nighttime lighting condition, the illumination of remote sensing objects is low and varies greatly, usually ranging from several lux to tens of thousands of lux. Nighttime light remote sensing imaging requires high sensitivity and large dynamic range of detectors. Luojia 1-01 is the first professional nighttime light remote sensing satellite in the world. In this paper, we took the nighttime light remote sensing camera carried on the satellite as research object, proposed an in-orbit SNR test method based on time series images to overcome the problem of low spatial resolution. We first analyzed the process of luminous flux transmission between objects and satellite and established a radiative transfer model. By combining the parameters of large relative aperture optical system and high sensitivity CMOS device, we established SNR model and specially analyzed the effect of exposure time and quantization bits on SNR. Finally we used the proposed in-orbit test method to calculate SNR of lighting images acquired by satellite. And the measured result is in good agreement with the model predicted data. Under the condition of 10lx illumination, the SNR of typical objects can reach 27.02dB, which is much better than the requirement of 20dB for engineering application.

The variety of risks due to climate change with a potential impact on Cultural Heritage CH requires a multidisciplinary approach and a preliminary overview of the existing methods for risk analysis and assessment in different fields. Thus, the starting point of the research conducted by the Sapienza PNRR working group consists in a systematic literature review of risk assessment approaches, methods and indicators. As a first outcome, the research has designed a multidisciplinary comprehensive framework consisting of the definition of risk categorization, the framework represented by a measurable index and the main target, according to the classification of Cultural Heritage based on the harmonization of European vocabularies definitions and protocols. The risk assessment framework sets the methodological core of a future multi criteria matrix and digital platform for decision focused on the historic built environment and it is functional to the definition of specific operational guidelines connected to each risk for elaborating descriptive/predictive Architectural Heritage’s transformation scenarios to support the development of mitigation and adaptation strategies.

Objective: Application of ERA methods to investigate the atmospheric pollution and built environment factors influencing lung cancer incidence rate in Chinese women. Methods: Lung cancer incidence rate among Chinese women at 339 cancer registries were obtained from the China Cancer Registry Annual Report 2017, air quality and built environment data were obtained from the Greenpeace and China Construction Yearbook. After multiple covariates variables were eliminated, an exploratory regression analysis was performed using the world standardized population incidence rate as the dependent variable. Air quality and built environment factors as the independent variable. Results: Shandong Peninsula, Hebei and Liaoning are high incidence rate areas of female lung cancer in China, with significant regional aggregation. In addition to air quality factors such as industrial smoke emission data, the association between built environmental factors such as urbanization rate, development LUI, population density and greening coverage of built-up areas and female lung cancer incidence rate is statistically significant. Conclusion: In addition to air quality factors, urban spatial factors can also significantly affect respiratory health. The LUI is positively while urbanization rates and population density are negatively correlated with the incidence rate of lung cancer. The role of green space for respiratory health has not been proven. In addition, there is little relationship between income and health, and similar findings are found for indicators such as the public transportation and roads network.

The rapid urbanization that takes place in developing regions such as Sub-Saharan Africa is associated with a large range of environmental and social issues. In this context, remote sensing is essential to provide accurate and up-to-date spatial information to support risk assessment and decision making. However, mapping urban areas remains a challenge because of their heterogeneity, especially in developing regions where the highest rates of misclassification are observed. Nevertheless, urban areas located in arid climates --- which are among the most vulnerables to anthropogenic impacts, suffer from the spectral confusion occurring between built-up and bare soil areas when using optical imagery. Today, the increasing availability of satellite imagery from multiple sensors allow to tackle the aforementioned issues by combining optical data with Synthetic Aperture Radar (SAR). In this paper, we assess the complementarity of the Landsat 8 and Sentinel-1 sensors to map built-up areas in twelve Sub-Saharan African urban areas, using a pixel-level supervised classification based on the Random Forest classifier. We make use of textural information extracted from SAR backscattering data in order to reduce the speckle noise and to introduce contextual information at the pixel level. Results suggest that combining both optical and SAR features consistently improves classification performances, mainly by enhancing the differentiation between built-up and bare lands. However, the fusion was less beneficial in mountainous case studies, suggesting that including features derived from a Digital Elevation Model (DEM) could improve the reliability of the proposed approach. As suggested by previous studies, combining features computed from both VV and VH polarizations consistently led to better classification performances. On the contrary, introducing textures computed from different spatial scales did not improve the classification performances.

We report the development of an extrinsic self-healing coating system that shows no fluorescence from the intact coating, yellowish fluorescence in cracked regions, and greenish fluorescence in healed regions, thus allowing the separate monitoring of cracking and healing of coatings. This fluorescence monitoring self-healing system consisted of a top coating, an epoxy matrix resin containing mixed dye-loaded in single microcapsule. The dye-loaded microcapsules consisted of a poly(urea-formaldehyde) shell encapsulating a healing agent containing MAT-PDMS and styrene, a photo-initiator and a mixture of two dyes, one that fluoresces only in the solid state (DCM) and a second that fluoresces dramatically increased in the solid than solution state (4-TPAE). A mixture of the healing agent, photo-initiator and the two dyes was yellow due to fluorescence from DCM. On UV curing of this mixture, however, the color changed from yellow to green and the fluorescence intensity increased due to fluorescence from 4-TPAE in the solid state. When a self-healing coating embedded with microcapsules containing the DCM/4-TPAE dye mixture was scratched, the damaged region exhibited a yellowish color that changed to green after healing. Thus, the self-healing system reported here allows the separate monitoring of cracking and healing based on changes in fluorescence color.

Categorical data analysis of 2 x 2 contingency tables is extremely common, not least because they provide odds and risk ratio statistics in medical research. The χ2 test is most often used, although some researchers use the likelihood ratio test (LRT). Does it matter which test is used? This paper argues that the LRT rather than the χ2 test should be used when we are interested in testing whether two variables are independent, as is typically the case. In contrast, the χ2 test should be reserved for where the data appear to match too closely a particular hypothesis (e.g. the null hypothesis), as may occur in the investigation of data integrity. Finally, it is argued that the evidential approach provides a consistent and coherent way in which tests can be made for each of these situations.

Background: The adoption of self-care behaviors among patients with congestive heart failure (CHF) is essential for the management of their health condition. However, there is a lack of tools for estimating self-care in CHF patients. We aim to develop and validate the Hippocratic heart failure self-care scale (HHFSCS). Methods: the scale includes 22 items which are reviewed by a committee of experts. Individuals indicate the frequency at which they follow each self-behavior on a five-point Likert scale. Adult patients with CHF (n=250) from a General Hospital, in Athens, were participated in the study from June 2020 to March 2021. Reliability coefficients and Explanatory Factor Analysis (EFA), using a Varimax rotation and the Principal Components Method were used to assess the psychometric measurements. Results: The Cronbach’s alpha coefficient of the HHFSCS was 0.807. The exploratory factor analysis identified two domains that accounted for 88.44% of the variance of the scale items; however, each sub-scale could not be used as an independent scale. Finally, the test-retest showed a significant strong correlation (r=0.973, p&lt;0.001). Conclusions: The HHFSCS is a reliable and valid tool for assessing self-behaviors in CHF patients. Health professionals can use it in their clinical practice to improve the management of patient’s health conditions.

Online education allows learners to develop knowledge and skills flexibly and conveniently—such observation among students whose characteristics involve student engagement, self-regulation, and self-efficacy. However, studies to characterize Filipino online learners seem lacking. Thus, this study aimed to characterize science education tertiary students in the Philippines concerning their online student engagement (OSE), self-regulated learning (SRL), and online learning self-efficacy (OLSE). The unprecedented events brought by COVID-19 pandemic also urged the implementation of online modalities while there is no available information on students’ online learning profiles. Hence, researchers used a survey research employed through ex post facto approach to determine the effects of the demographic profile on OSE, SRL, and OLSE. The survey was participated by N=373 respondents who answered the questionnaire with informed consent administered via Google Forms. Results revealed that OSE indicators moderately characterized students, while SRL and OLSE indicators are true of them, substantiated by the overall mean M=3.85(SD=0.90), M=3.86(SD=0.92), and M=3.14(SD=0.73), respectively. Also, multivariate tests showed no significant effect among the independent groups (p&gt;0.05), except for gender and OLSE interaction (p&lt;0.05) so, only in OLSE was a significant difference found in gender. In conclusion, Filipino online learners are moderate across aspects of student engagement, self-regulation, and self-efficacy.

Secure attachment, developed through consistent relationships with attachment figures in childhood, is a crucial factor in fostering healthy interpersonal relationships and a positive self-perception. This research aimed to assess how perceived security, as an indicator of secure attachment, predicts adult self-concept through the mediating effects of resilience and positive self-esteem. A quantitative, cross-sectional, and non-probabilistic study was conducted with 383 participants, of whom 76.2% were females, aged between 17 and 86 years (M = 28.52, SD = 12.23). Correlational analyses revealed significant positive associations between perceived security, self-concept, resilience, and positive self-esteem. Path analysis demonstrated that resilience and positive self-esteem sequentially mediate the relationship between perceived security during childhood and adult self-concept (Total Effect R2 = .34, F(1,381) = 193, p < .001; Indirect effect of sequential mediation b = .02, CI 95% [.01, .04]). Findings suggest that the ability to cope with ad-versity and personal acceptance underlie the impact of perceived security on self-concept. It is recommended to promote not only secure attachment in family interventions but also resilience and self-esteem in programs targeting adolescents, youth, and adults.

Purpose: To identify the impact of dealing with COVID-19 patients in clinical areas on nurses' professional self-concept and self-confidence. Background: Professional self-concept is considered a critical factor in the recruitment/retention process in nursing, nursing shortage, career satisfaction, and academic achievements. Professional self-confidence is also a crucial determinant in staff satisfaction, reducing turnover, and increasing work engagement. Design: Descriptive, comparative study. Methods: The study was conducted between February to May 2021 by utilizing a convenience sampling technique. A total of 170 nurses from two facilities were recruited from two COVID-19 and non-COVID-19 designated facilities. The level of professional self-concept and self-confidence was assessed by utilizing the Nurses' Self-Concept Instrument and Self-Confidence Scale. Results: The professional self-concept level among the exposed group to COVID-19 patients was lower than the comparison group, while the professional self-confidence level among the exposed group to COVID-19 patients was similar to the comparison group. On the other hand, the satisfied staff and those who received professional training in dealing with COVID-19 patients reported a higher level of professional self-concept. Conclusions: Dealing with COVID-19 patients has an impact on professional self-concept; the exposure group was lower than those who did not deal with COVID-19 patients, while the professional self-confidence level among the exposed group was similar to the comparison group. Getting professional training in dealing with COVID-19 patients and being satisfied at work were significant factors in improving the professional self-concept. Policymakers should create strategies that target the improvement of professional training in dealing with COVID-19 patients.

Background: Level of perceived competence as a basic psychological need could trigger achievement of diabetes self-management goals. Due to lack of a specific data collection tool to measure level of self-competence among Persian speaking patients with diabetes this study was conducted for cross-cultural adaptation and psychometric assessment of the Persian version of Perceived Competence Scale for Diabetes (PCSD-P). Methods: Standard translation/back-translation procedure was carried out to prepare a preliminary draft of the PCSD-P. Content and face validity of the early draft were checked by an expert panel including 15 scholars in the field of health education and promotion as well as nursing education with experience of working and research on diabetes. The final drafted questionnaire was completed by 177 randomly selected patients with type 2 diabetes. Based on the collected data structural validity of the contrived version was appraised using exploratory and confirmatory factor analysis (EFA, CFA). Cronbach's alpha and Intraclass Correlation coefficients (ICC) were used to check the scale’s reliability and internal consistency. ; (3) Results: The estimated measures of Content Validity Index (CVI= 0.95) and Content Validity Ratio (CVR= 0.8) were in the range of acceptable recommended limits. The EFA analysis results demonstrated a single factor solution according to the items’ loadings for the component. The model fit indices i.e. RMSEA= 0.000, CFI=1, TLI=1, GFI= 0.998, NFI= 0.999 RFI= 0.995 confirmed consistency of the hypothesized one-factor solution. Values of the internal consistency and reliability coefficients were also in the vicinity of acceptable range (α= 0.892, ICC=0. 886, P= 0.001). Conclusions: The study findings revealed good internal validity and applicability of the PCSD-P to measure degree of self-competence among Persian speaking type 2 diabetes patients to manage the chronic disease. Due to unrepresentativeness of the study sample future cross-cultural test of PCSD-P on diverse and broader Persian speaking populations is recommended.

This paper addresses the development of knowledge and assessment-centered learning approaches within a reflective learning framework in a first year physics class in a university faculty. The quality of students’ reflections was scored using a Self-reporting Reflective Learning Appraisal Questionnaire at the end of each learning approach. The results showed the differences between the approaches based on reflections on the learning control through self-knowledge, by connecting experience and knowledge, as well as through self-reflection and self-regulation. Assessment-centered activities fundamentally help students identify aspects of their attitudes towards, as well as regulate, their sustainability learning education.