The BIOTON® biochar, produced by a wood biomass pyrolysis process, usually applied as a soil amendment, was investigated for a novel application, i.e. the adsorption of lead from contaminated solutions. The experimental activity firstly included the physical-chemical characterization of BIOTON®; SEM images were also obtained to highlight its internal structure. The adsorption process was investigated through batch and column experiments. Adsorption kinetics showed a very rapid achievement of the equilibrium conditions, i.e. at 2h and 4h for 50 mg/L and 100 mg/L initial Pb concentration, respectively. Complete removal also occurred within the same time. The Brunauer–Emmett–Teller model better fitted the equilibrium data for both Pb concentrations, whereas the kinetics were best represented by the pseudo second order model. The column tests showed that the addition of biochar as adsorbent media within the bed significantly extended the time of breakthrough and exhaustion, with respect to the column filled with soil only. The adsorption capacities of BIOTON® versus lead solutions was found to be comparable to that reported for commercial adsorbents. Therefore, BIOTON® can be considered a valid option, with the additional benefit to reduce the environmental impact since allows to recover a residue which alternately would need to be disposed of.

The present work demonstrates the new nanofiber mats prepared through co-electrospinning of two different polymers i.e. corn protein namely Zein and Nylon-6. The composite nanofiber membrane was used as an effective adsorbent material for the removal of toxic reactive dye i.e. Reactive Blue 19 (RB 19) from water solution. These co-electrospun nanofibers had good mechanical strength compared to zein nanofibers alone. Experimental results suggested that zein/nylon nanofibers have greater potential for total removal of RB19 at room temperature within 10 min of contact time from aqueous solution. The maximum capacity was found to be 70 mg/g of nanofibers. The mechanism of RB19 removal on proposed nanofibers is mainly through hydrogen bond and electrostatic means.

Elevated antimony concentrations in aqueous environments from anthropogenic sources is becoming of global concern, here iron oxides are known to strongly adsorb aqueous antimony species with different oxidation states, but the effect of silica on the removal characteristics is not well understood despite being a common component in the environment. In this study, ferrihydrite was synthesized at various Si/Fe molar ratios to investigate its adsorption and co-precipitation behaviors with aqueous antimony anionic species, Sb(III) and Sb(V). The XRD analyses of the precipitates showed two broad diffraction features at approximately 35° and 62° 2θ, which are characteristic of 2-line ferrihydrite, no significant shifts in peak positions in the ferrihydrite regardless of the Si/Fe ratios. The infrared spectra showed a sharp band at ~990 cm⁻¹, corresponding to asymmetric stretching vibrations of Si-O-Fe bonds which increased in intensity with increasing Si/Fe molar ratios. Further, the surface charge on the precipitates became more negative with increasing Si/Fe molar ratios. The adsorption experiments indicated that Sb(V) was preferentially adsorbed at acidic conditions and decreased dramatically with increasing pH while the adsorption rate of Sb(III) ions was independent of pH, however, the presence of silica suppressed the adsorption of both Sb(III) and Sb(V) ions. The results showed that Sb(III) and Sb(V) ions were significantly inhibited by co-precipitation with ferrihydrite even in the presence of silica by isomorphous substitution in the ferrihydrite crystal structure.

In this review, we covered the recent advances in synthesis of gold nanoparticles and their uses in degradation of dyes. This study provides framework to develop a low cost, ecofriendly and highly efficient synthesis of gold nanoparticles. These synthetic methods do not produce any toxic byproduct. The present study is focus on removal of dyes by Au-NPs because gold nanoparticles act as good absorbent for dyes in short time. Synthesis of Au-NPs from plant extract e.g. marine alga, Scutellarin Barbata, A.nigra, Fruit peels, Bacillus marisflavi from raw silk cocoons, amylopectin and poly acrylic acid, L.asparagine, Grephene oxide, IPEI coated Au-NPs. The synthesizes Au-NPs were used further for removal of dyes like methylene blue (MB), Rhodamine B (RB) Degradation, methylene orange, acid red degradation, Congo red.

Large-scale volumetric fracturing is generally used during shale gas development. The return rate of fracturing fluid is low, and a large amount of slickwater will be retained in the reservoir. The adsorption and desorption of partially hydrolyzed polyacrylamide (HPAM), an additive commonly used in slickwater, on the surface of shale was studied using Longmaxi Shale from the Sichuan Basin. The experimental results showed that the mass ratio of the HPAM solution to shale reached saturation adsorption at 20:1 when the concentration of HPAM solution was 1000 mg/L and 25:1 when the concentration of HPAM solution was 500 mg/L. The mass ratio of the HPAM solution to shale was fixed at 25:1, and the adsorption equilibrium was reached at a HPAM concentration of 1000 mg/L when the aqueous solution temperature was 30°C and 800 mg/L when the aqueous solution temperature was 60°C. The Langmuir adsorption model yielded a better fit than the Freundlich adsorption model. The adsorption equilibrium time at 30°C was at 60 min for a HPAM concentration of 500 mg/L, while for a concentration of 1000 mg/L, it was at 90 min. The adsorption equilibrium time at 60°C was 40 min for a HPAM concentration of 500 mg/L, whereas it was 60 min for a HPAM concentration at 1000 mg/L. The pseudo-second order kinetics model yielded better fits than the pseudo-first order kinetics model. The adsorption of HPAM on shale was strong, and the adsorbed HPAM resembled cobwebs adhering to the shale surface. HPAM on the surface of shale after adsorption could resist the desorption capacity of water. However, when the amount of adsorbed HPAM on shale increased significantly, the amount of residual HPAM on the surface of the shale decreased rapidly during desorption in deionized water. The desorption of HPAM on the shale surface followed a modified desorption model. The higher the concentration of HPAM adsorbed on the shale surface was, the easier it was to desorb, the easier it was to be removed from the shale.

This study deals with the preparation of adsorbents from a commercial xerogel by chemically modifying its surface with concentrated mineral acids and alkali metal chlorides, their physicochemical characterization, and their use as adsorbents for gallic acid in aqueous solution. The prepared adsorbents have a high specific surface area (347-563 m2 g-1), better pore development for samples treated with alkali metal chlorides than with mineral acids and are more acidic than the initial xerogel (p.z.c range 2.49-6.87 vs. 7.20). The adsorption properties of the commercial xerogel improved over a wide range of pH and temperature. The experimental results indicate that the adsorption process is thermodynamically favored.

The high reactivity of acetylene group the formation of strong chemical bonds with active sites on mineral surfaces, thereby improving the flotation performance of gold minerals. This study utilized Density Functional Theory (DFT) to analyse the quantum chemical parameters of structure, Mulliken population, and the frontier orbitals of a thioester collector containing an acetylene group, PDEC (prop-2-yn-1-yl diethylcarbamodithioate). PDEC is compared with analogous thioester collectors Z-200 and Al-DECDT, and the interaction mechanism of PDEC on the Au(1 1 1) surface is simulated, followed by empirical validation through adsorption experiments. The findings indicate that S atom of PDEC in the carbon-sulfur group exhibit shorter covalent bond lengths, and reduced carbon-sulfur double bonds and Mulliken population, resulting in enhanced electron localization. This confers greater selectivity to PDEC during its adsorption on mineral surfaces. Frontier orbital analysis shows that the electrons of acetylene group possess a notable electron-accepting capacity, significantly influencing frontier orbital energy of PDEC and playing a pivotal role in the bonding interaction with mineral surfaces. Both the S atom in carbon-sulfur group and its acetylene group establish stable adsorption structures with the A(111) surface in a single coordination mode. The adsorption energy sequence is PDEC > Al-DECDT > Z-200. Partial density of states demonstrates that S 3p orbit of carbon-sulfur group hybridize with Au 5d orbit, while the C 2p orbit of the acetylene group engage in weaker back-donation bonding with Au 5d orbit. This is corroborated by electron density difference and post-adsorption Mulliken population analyses, revealing that S atom of carbon-sulfur group in PDEC donate electrons to Au atom, forming dominant positive coordination bonds, whereas the acetylene group accepts partial electrons from Au atom, resulting in weaker back-donation bonds. The adsorption experiments align with the DFT adsorption energy results.

Elevated ammonium (NH4+) concentrations in untreated waterways contribute to eutrophication and dissolved oxygen depletion, which cause severe degradation of water quality. Ion exchange processes are a robust, low operational cost and efficient option for ammonium removal with zeolites being the most widely used. Geopolymers are a sustainable and low-cost option compared to zeolites that follows the same ion exchange technology. In the present study, a metakaolin-based porous geopolymer was synthetized, characterised and validated as adsorbent material. The laboratory batch tests showed a maximum adsorption capacity (Qm) of 18.35 mg/g being 27% higher than reference zeolites. Kinetics followed the Weber-Morris rate equation being the intraparticle diffusion the limiting process and continuous experiments indicated a maximum removal of 97% in the first hours. The material was validated in a wastewater treatment pilot plant where values in pH, electrical conductivity and NH4+ concentration were monitored. The obtained data indicated that the material achieved up to 80% NH4+ removal which is similar to traditional zeolites. The results demonstrate that this sustainable, low-cost and easy-to-install metakaolin-based geopolymer can be used effectively for NH4+ treatment.

Volatile organic compounds (VOCs) are molecules present in our everyday life, and they can be positive, such as in the formation of odour and food flavour, or harmful for environment and humans, and the research is focusing on limiting their emissions. Various methods have been used to achieve this purpose. Firstly, we review three main degradation methods: activated carbon, photocatalysis and a synergetic system. We provide a general overview of the operative conditions and report the possibility of VOC abatement during cooking. Within the literature, none of these systems has ever been tested in presence of complex matrices, such as during a cooking process. The aim of this study is to compare the three methods in order to understand the behaviour of filter systems in the case of realistically complex gas mixtures. Proton Transfer Reaction - mass spectrometry (PTR-MS) has been used as real-time monitoring of volatilome. Since VOC emissions are highly dependent on the composition of the food cooked, we evaluated the degradation capacity of the three systems for different burger types (meat, greens and fish). We demonstrate pros and cons of the photocatalysis and adsorption and how a combined approach can mitigate the drawbacks of photocatalysis.

Using banana peel as raw material, the adsorption properties of hydrothermal carbon pre-10 pared from banana peel modified with different concentrations of phosphoric acid solution for lead 11 ions in aqueous solution were studied. The surface structure and functional groups of the modified 12 hydrothermal carbon were analyzed by XRD and SEM. The results show that the surface of the 13 modified banana peel hydrothermal carbon prepared at 240℃ and 2mol/L phosphoric acid solution 14 has large pores. The adsorption capacity is larger when pH value is 6.When the concentration of 15 phosphoric acid solution was 2mol/L, the solid-liquid ratio was 2g/L, the adsorption capacity was 16 40.64mg/g, and the removal rate was 82.74%.When the initial concentration of lead solution in-17 creased to 100mg/L, the adsorption capacity of modified hydrothermal carbon for lead ion increased 18 to 76.81mg/g, and the removal rate decreased to 76.81%.The equilibrium adsorption time of banana 19 peel phosphoric acid modified hydrothermal carbon for lead ions in solution is 300min. The adsorp-20 tion process satisfies the pseudo-second-order kinetic model and Langmuir isotherm equation. The 21 reaction temperature is 313K, and the equilibrium adsorption capacity can reach 101.19mg/g. The 22 adsorption of Pb ions in aqueous solution by phosphoric acid modified hydrothermal carbon is 23 dominated by single layer chemisorption. The artificial neural network has a fitting correlation of 24 0.99, and the adsorption process includes physical adsorption, electrostatic attraction, ion exchange, 25 and surface complexation.

Water pollution is regarded as a dangerous problem that needs to be resolved right away. This is largely due to the positive correlation between the increase in global population and waste production, especially food waste. Hydrogel beads based on sodium alginate (Alg) and pomegranate fruit peels (PP) were developed for the adsorption of Safranin O dye (SO) in aqueous solutions. The obtained Alg-PP beads were widely characterized. The effects of the contact time (0-180 min) and initial concentration (10-300 mg/l), the initial pH (2-10), the adsorbent dosage (1-40 g/l) and the temperature (293-333 K) were investigated through batch tests. The data proved that the adsorption kinetics of SO reached equilibrium within 30 min and up to 180 min. The adsorption data of SO onto synthesized beads follow the pseudo second-order model. The experimental data fitted very well to both Freundlich and Langmuir models. The maximum adsorption capacity of Alg-PP could reach 8.99 mg/g at 293 K. Calculation of Gibbs free energy and enthalpy indicated that adsorption of SO onto Alg-PP is spontaneous and endothermic. Finally, analysis of diffusion and mass transport phenomena were presented. The reported results revealed that the Alg-PP beads could be used as a novel natural adsorbent for the removal of cationic dye pollutants from aqueous environments.

Due to the accumulation of pesticides in the environment, the development of efficient strategies for their removal is of utmost importance. Activated carbons are currently seen as excellent candidates for adsorptive pesticide removal based on several beneficial properties, like a large surface area, developed porosity, and low price. However, a deep link between materials' properties and performance is still elusive. Here we focus on the kinetics of three organophosphate pesticides removal, aliphatic dimethoate and malathion and aromatic chlorpyrifos, using a series of carefully prepared activated carbon fibers. Used adsorbents have a wide range of specific surface areas, pore size distributions, and elemental content, allowing the establishment of the link between physicochemical properties and their performance as adsorbents. We use data analysis tools to link these properties and discuss their different roles in the removal of three structurally different yet extremely dangerous pesticides. The obtained results can guide the synthesis of novel adsorbents or rationally select adsorbents for specific target pollutants based on the physicochemical properties of adsorbents and the chemical structure of pollutants.

Biochar has high potential usage in retaining various contaminants, wastewater treatment, and water purification. In this study, three rice husk derived biochars with pyrolysis temperature 300, 400 and 500 ºC, respectively, and pristine rice rusk were used to remove cadmium from aqueous solution. The results showed that about 70% or more of Cd2+ adsorption occurred in the first 960 mins of adsorption kinetics. The Cd2+ adsorption capacity under equilibrium increased with increasing pyrolysis temperature, probably attributed to the increased specific surface area (SSA) under higher pyrolysis temperature noting that significant linear correlation occurred between Cd2+ adsorption capacity and SSA. The Cd2+ adsorption could be best fitted by pseudo-second order model relative to Elovich model and pseudo-first order model. The Cd2+ adsorption rates were higher in film diffusion stage, indicating that film diffusion stage was significant and fast in the early stage of Cd2+ adsorption. In contrast, Cd2+ adsorption by intra-particle diffusion accounted for 47.0%, 47.9% and 43.9% on average of the total Cd2+ adsorption, respectively, indicating that intra-particle diffusion of Cd2+ played a more predominant role in limiting Cd2+ adsorption rate. When reaching Cd2+ desorption equilibrium, removal ratio (RR) values were averaged 0.96, 0.91, and 0.90 under three initial concentrations. More than 90 percentage on average of Cd2+ was removed from aqueous solution by biochars and rice rusk as well, thus biochars can be used to efficiently remove contaminants from aqueous environment. Cation exchange, electrostatic attraction, and the complexation with surface functional groups could be the main dominant mechanisms for Cd2+ adsorption-desorption on biochars.

Chemical weed control using herbicide glyphosate to manage emerged weeds is an important production practice in Florida citrus. Despite the extensive use of glyphosate in citrus orchards, very limited information is available on its environmental fate and behavior in Florida soils that are predominantly sandy in nature. Hence, the study's objective was to understand the adsorption-desorption, dissipation dynamics, and vertical movement or leaching of glyphosate in sandy soils in citrus orchards. Laboratory, field, and greenhouse experiments were conducted at Southwest Florida Research and Education Center in Immokalee, Florida. The adsorption-desorption behavior of glyphosate in the soils from three major citrus production areas in Florida was studied utilizing a batch equilibrium method. The dissipation of glyphosate was tracked in the field following its application at the rate of 4.20 kg ae ha-1. Soil leaching columns in greenhouse conditions were used to study the vertical movement of glyphosate. The results suggest that glyphosate has a relatively lower range of adsorption or binding (Kads = 14.28 to 30.88) in the tested soil types. The field dissipation half-life (DT50) of glyphosate from surface soil was found to be 26 days. Glyphosate moved vertically or leached into the soil profile, up to 40 cm in the soil column, when analyzed 40 days after herbicide application. The primary degradation product of glyphosate, i.e., aminomethyl phosphonic acid (AMPA), was also detected up to the depth of 30 cm below the soil surface, indicating the presence of microbial metabolism of glyphosate in the soil.

Scale inhibitors are deployed as preventive and rejuvenation operation in oil and gas industry when production operations are under threat or menace of scale blockage. The application of scale inhibitors is carried out through a method known as squeezing. In general, the squeeze process is governed by inhibitor-rock interaction which is described by adsorption/desorption isotherm. Most reservoirs produce loose sand grains or fine sand which float and flow within the pore spaces along with the squeezed scale inhibitors. Hypothetical reports have shown that not all scale inhibitors pumped into the formation adsorb onto the formation rock. A number of factors (irreversible adsorption, pH changes, competing ions, concentration and temperature) have been considered to affect the adsorption and return profile of these scale inhibitors. This review work examines the performances of most common scale inhibitors used in the oil and gas production activities, theoretical application in reservoirs and how loose fine sand grains affect the adsorption and desorption characteristics of squeezed scale inhibitors. Additionally, presented were overviews of previous reports on fine sand production and migration of fine sands through formation pores in reservoirs.

Lanthanum chemical compound incorporates a sensible anionic complexing ability, however lacks stability at low pH scale. Biochar fibers will benefit of their massive space and plethoric useful teams on surface to support metal chemical compound. Herein, wet spinning technology was used to load La3+ onto sodium alginate fiber, and convert La3+ into La2O3 through carbonization. The La2O3 modified biochar (La-BC) fiber was characterized by SEM, XRD and XPS, etc. The adsorption experiment proved that La-BC showed excellent adsorption capacity for chromates, and its saturation adsorption capacity was about 104.93mg/g. The information suggested that the adsorption was in step with both Langmuir and Freundlich model, followed pseudo-second-order surface assimilation mechanics, which instructed that the Cr (VI) adsorption was characterized by single-phase and polyphase adsorption, mainly chemical adsorption. Thermodynamic parameter proved that the adsorption process was spontaneous and endothermic. The mechanistic investigation revealed that the mechanism of adsorption of Cr (VI) by La-BC may include electrostatic interaction, ligand exchange or complexation. Moreover, co-existing anions and regeneration experiments proved that La-BC was recyclable and had a good prospect in the field of chrome-containing wastewater removal.

Solid-liquid interfacial phenomena play an essential role in our everyday lives and are often regarded as the outcome of interactions at the solid-liquid interface. However, the intricately intrinsic mechanism underlying interfacial interactions renders in-situ simulations and direct measurements challenging. As an effective analytic method for studying solid-liquid interfacial interactions, Microcalorimetry can provide the most basic thermodynamic information (including changes in enthalpy, entropy, and Gibbs free energy during solid-liquid binding/separation processes), which is extremely crucial for understanding interaction directionality and limitation. This review is dedicated to highlighting the pivotal role of microcalorimetry in studying solid-liquid immersion and adsorption processes. Specifically, we provide an overview of the commonly employed microcalorimetric methods, delve into the influence factors of enthalpy change, and finally discuss the specific applications of microcalorimetry in studying various solid-liquid binding processes. There remains a vast expanse of thermodynamic information regarding solid-liquid interactions that await exploration via calorimetry.

Changes in the atomic and electronic structure of silicon carbide 3C-SiC (β-SiC), resulting from lead adsorption, have been studied within the density functional theory. The tests were conducted for three representative surfaces with varying degrees of lead coverage. Results indicate that chemisorption occurs, with the strongest binding, found on the hexagonal surface (111) in interaction with three dangling bonds. The adsorption energy rises with increasing coverage, especially as the surface approaches saturation. Analysis of the data was focused on parameters important for corrosion processes such as bond distances, binding energies, Bader charges and charge density difference.

One of the strategies to reduce the contents of the low density lipoproteins (LDLs) in a blood is a hemoperfusion, in which case they are selectively retracted from plasma by an adsorber located outside the patient body. Recently, a photo-controllable smart surface was developed for this purpose characterised by high selectivity and reusability [C.Guo et al., ACS Applied Materials & Interfaces 2022, DOI:10.1021/acsami.2c07193]. We present a mesoscopic model for such a setup involving the azobenzene-containing polymer brush and the model LDL particles. The latter comprise an uniform spherical core covered by a shell of elongated particles representing phospholipids. The system is studied using the coarse-grained molecular dynamics simulation. We examined the dependences of the binding energy on both the length of polymer chains and the grafting density of a brush, and established optimal conditions for the adsorption. These are explained by a competition between the concentration of azobenzenes and phospholipids in the same spatial region, flexibility of polymer chains, and excluded volume effects.

Retention mechanisms in HILIC have been investigated and reported in literature. However, the current understanding of the retention mechanisms is qualitative and lacks quantitative details. Previously, mechanism elucidation was based on indirect evidence, and unambiguous assignment of retention mechanisms has not been reported based on direct data. This study aims to quantitatively determine the contributions of two major retention mechanisms in HILIC, hydrophilic partitioning and surface adsorption to the overall retention of neutral compounds. Using the methodologies we developed previously, the phase ratio for adsorbed water layer and distribution coefficients were measured and used to calculate the retention factors attributed to hydrophilic partitioning. The methodology allows the determination of the contribution of surface adsorption simultaneously. The evaluation of five test compounds demonstrates that the retention may be controlled by hydrophilic partitioning, surface adsorption or both depending on compound characteristics. Quantitative assessment of retention mechanisms also makes it possible to better understand the effect of acetonitrile on retention in HILIC.

Modified aluminum slag (MAS) was applied as an adsorbent for Congo red (CR) prepared by the hydrothermal treatment of Ca (OH) 2. At 25 ℃, with a MAS dosage of 0.3g, initial CR concentration of 100 mg/L and initial pH=5, and the adsorption time was 40 min, the CR removal efficiency was 98.41%. The adsorption trend of CR conformed to the second-order kinetics, and the adsorption isotherm follows the Freundlich isotherm model. Compared with RAS, MAS has a larger pore volume and specific surface area. The mechanism of action of MAS on CR was the interaction between membrane diffusion and internal diffusion, and the adsorption rate during the membrane diffusion was the fastest.

The methylene blue (MB) adsorption was performed on a natural material powder of Cynarascolymus as identified by Cs. To analyze the Cs material, FTIR, SEM, isoelectric point (pHpzc) analysis, TGA, and DRX were used. The maximum experimental adsorption capacity of the Cs material was 203.333, 192.187, and 179,380 mg•g-1 at 298, 303, and 313 K, respectively. The correlation coefficients (R2) and average percentage errors APE(%) values for the kinetic and isotherms models indicated that the adsorption kinetics fol-lowed a pseudo-nth order model and that the Traditional isotherm model Red-lich-Peterson (R-P) correctly described the experimental data obtained at 298, 303, and 313 K, respectively. The steric, energetic, and thermodynamic characteristics of the most rele-vant advanced model (double-energy single-layer model (AM 2)) were analyzed in detail. The number of active sites for the first receptors (n1) was determined to be 0.129, 0.610, and 6.833; whereas the number of second active sites (n2) was determined to be 1.444, 1.675, and 2.036 at 298, 303, and 313 K, respectively. This indicated the presence of both multi–docking and multimolecular modes for the first style of MB ions (n1); while only a multi-molecular mode for the second style of MB ions (n2). Thermodynamic characteristics demonstrated that MB adsorption onto the Cs adsorbent is spontaneous and feasible.

This report aimed to know the performance of local mineral-based composite ceramic. The materials used consist of Indonesian local minerals, which are jarosite and manganite minerals as sources of oxide iron and Mangan. The materials were synthesized using the precipitation method, whereas composite ceramic was fabricated using a screen printing method and fired at 600 oC using a furnace. The results of the characterizations indicate that the sample forms three phases on diffraction peaks. The differences in the resistance values in ambient and ethanol environments indicate that the sample has very different responses. The high porosity of the sample greatly support the gas adsorption process. Thus, the sample has a high level of sensitivity. With the above characteristics, the composite ceramic which was fabricated has the potential to be applied to gas sensors, especially ethanol gas sensors.

This paper uses polypropylene (PP) as the matrix and acrylic acid (AA) and maleic anhydride (MAH) as functional monomers to prepare PP-g-(AA-MAH) fibers by suspension grafting and melt-blown spinning technology that are easy to industrially scale-up. The fibers can be used to adsorb aniline from wastewaters. Results showed that the grafting ratio reached the maximum of 12.47%. The corresponding optimal conditions were grafting time of 3h, AA : MAH = 0.75, total monomer content of 55%, benzoyl peroxide 1.4%, xylene concentration of 6 mL/g PP, and deionized water content of 8 mL/g PP. Owing to its good fluidity and thermal stability, the product of suspension grafting can be used for melt-blown spinning. Infrared spectroscopic and nuclear magnetic resonance spectroscopic analyses indicated that AA and MAH were successfully grafted onto PP fibers. After grafting, the hydrophilicity of PP-g-(AA-MAH) fiber increased. Therefore, it had higher adsorptivity for aniline and the adsorption capacity could reach 42.2 mg/g at 45 min. Moreover, the PP-g-(AA-MAH) fibers showed good regeneration performance.

The high environmental impact of conventional methods of cooling and heating has increased the need for renewable energy deployment for covering thermal loads. Towards that direction, the proposed system aims at offering an efficient solar powered alternative, coupling a zeolite-water adsorption chiller with a conventional vapor compression cycle. The system is designed to operate under intermittent heat supply of low-temperature solar thermal energy (<90 °C) provided by evacuated tube collectors. A prototype was developed and tested in cooling mode operation. The results of separate components testing showed that the adsorption chiller was operating efficiently, achieving a maximum coefficient of performance (COP) of 0.65. With respect to the combined performance of the system, evaluated on a typical week of summer in Athens, the maximum reported COP was approximately 0.575, mainly due to the lower driving temperatures at a range of 75 °C. The corresponding mean energy efficiency ratio (EER) obtained was 5.8.

Zinc is mostly extracted from zinc oxide and sulfide minerals, and this process involves flotation as a key step. While it is easier to float the sulfide mineral, its consumption and depletion has led to an increased reliance on zinc oxide minerals, including smithsonite; hence the development of efficient ways of collecting smithsonite by flotation is an important objective. Herein, we describe the use of 2-(hexadecanoylamino)acetic acid (HAA), a novel surfactant, as a collector during smithsonite flotation. The mechanism and flotation performance of HAA during smithsonite flotation were investigated by total organic carbon (TOC) content studies, zeta potential measurements, FTIR spectroscopy, and XPS analyses, combined with micro-flotation experiments. The flotation results revealed that HAA is an excellent collector in pulp over a wide pH range (9–12) and at a relatively low concentration (2 × 10^‒4 mol/L), at which a recovery of close to 90% of the smithsonite mineral was obtained. TOC-content studies reveal that the good flotation recovery is ascribable to large amounts of collector molecule adsorbed on the smithsonite surface, while zeta potential measurements show that the HAA is chemically adsorbed onto the smithsonite. FTIR and XPS analyses reveal that the HAA-collector molecules adsorb onto the smithsonite surface as zinc-HAA complexes involving carboxylate moieties and Zn sites on the smithsonite surface in alkaline solution.

In recent years, the need for safe and modern composite barrier for the prevention of groundwater contamination and the provision of Geo-environmental protection has been studied together with the need of designing low cost and effective liner for isolating landfill contents from the environment. In this study, various mix designs involving two natural adsorbents, the Na-Bentonite and the pH-adjusted sawdust were prepared for a series of Geo-environmental experiments to be carried out to determine the adsorption capacity, buffering capacity, pH changes, and COD changes among others, in the presence of Pb(NO3)2 contaminant concentrations. Generally, the results showed an increase in adsorption capacity in the acidic segment of the treatment. An increase of 58% of the adsorption efficiency of the Na-Bentonite in adsorbing the contaminant at the highest concentration was the most important achievement of the system while in the acidic segment.

We investigate the ammonium removal abilities of natural and synthetic zeolites, which have distinct Si/Al ratios and various surface areas, to study how adsorption and ion-exchange processes in zeolites perform under different ammonium concentrations and different temperatures. Five zeolites including natural mordenite, chabazite, erionite, clinoptilolite and synthetic merlinoite were immersed in 20 mg/kg, 50 mg/kg and 100 mg/kg ammonium solutions. The results demonstrate that zeolites under high ammonium concentrations (100 mg/kg) possess higher physical adsorption capacity (0.398–0.468 meq/g), whereas those under lower ammonium concentrations (20 mg/kg) possess greater ion-exchange property (64–99%). The ion-exchange ability of zeolites are extremely dependent on the cation content of the zeolites, and the cation content is affected by the Si/Al ratio. The surface area of zeolites also has a partial influence on its physical adsorption ability. When the surface area is less than 100 m²/g, the adsorption ability of zeolite increases obviously with surface area; however, adsorption ability is saturated as the surface area becomes larger than this critical value of 100 m²/g. When we carried out the zeolites in 50 mg/kg ammonium concentration at different temperatures (5~50 ℃), we found that zeolites exhibit the highest ammonium removal ability at 30°C and the potassium release was enhanced at 30~40 ℃.

Smoked cigarette butts (SCB) can be used as precursors to obtain activated carbon (AC) due to their high carbon content related to the presence of cellulose acetate and components that are retained in the tobacco combustion process. In this way, it was analyzed how the process of pyrolysis or formation of char from this residue occurs, for this a study of the kinetics of formation of char is carried out by thermogravimetry, using three heating speeds 5, 10 and 15 °C/min. Based on the data obtained, mathematical models such as Kissenger - Akahira - Sunose (KAS), Starink (STK) and Ozawa - Flynn - Wall (OFW) were used in order to identify thermodynamic parameters through the energy of activation. The char obtained was subjected to an activation treatment with KOH in order to increase the surface area and pore volume, obtaining values of 433 m2/g of BET area and 0.25 cm3/g of micropore volume. Finally, the adsorbent was applied in the removal of Cr (VI) obtaining a Qmax capacity determined by the Langmuir model of 55.8 mg/g.

A novel polymer containing β-cyclodextrin, α-cyclodextrin, γ -cyclodextrin and chitosan (cy-clodextrin-chitosan) was synthesized, characterized and used for extracting two kinds of pharmaceuticals ibuprofen and progesterone. This polymer is amorphous and porous with a high swelling capacity. The cyclodextrin-chitosan polymer exhibits high extraction capacity towards progesterone and ibuprofen. Add to that, the effect of different operator variables was studied and discussed (i.e., the effects of contact time, solute concentration, pH, ionic strength and temperature). In this study adsorption kinetic was investigated, where it follows a pseudo-second order model in case of ibuprofen and progesterone.

A new study for CH4 reforming to hydrogen and hydrogen storage was performed using magnesium-based alloy. MgH2-12Ni (with the composition of 88 wt% MgH2 + 12 wt% Ni) was prepared in a planetary ball mill by milling in hydrogen atmosphere (reaction-involved milling). X-ray diffraction (XRD) analyses were performed for the samples after reaction-involved milling and after reactions with CH4. The variation of adsorbed or desorbed gas with time was measured by a Sieverts’ type high-pressure apparatus at 773 K. The microstructures of the powders were observed using scanning transmission microscope (STEM) with energy-dispersive X-ray spectroscopy (EDS). The synthesized samples were also characterized using Fourier Transform Infrared (FT-IR) spectroscopy. XRD pattern of MgH2-12Ni after reaction with CH4 of 12 bar at 773 K and decomposition under 1.0 bar at 773 K exhibited phases of MgH2 and Mg2NiH4. This shows that reforming of CH4 was occurred, hydrogen produced after reforming of CH4 was then adsorbed on the particles, and hydrides were formed during cooling to room temperature. Ni and Mg2Ni formed during heating up to 773 K are believed to have brought about catalytic effects for reforming CH4. MgH2-12Ni adsorbed 0.8 wt% reformed CH4 within 1 min in a reaction with CH4 of 12 bar at 773 K and then desorbed 0.8 wt% reformed CH4 (hydrogen-containing mixture) within 1 min under 1 bar at 773 K. Attenuated total reflectance FT-IR spectroscopy (ATR-FTIR) spectra of MgH2-12Ni after reactions under 12 bar CH4 at 723 K and 773 K showed peaks of C-H bending, C=C stretching, O-H stretching, O-H bending, and C-O stretching.

Tackling global warming and the consequent climate change in our planet is of urgent importance to our society. Renewable biomass derived carbons have been studied as promising adsorbents, but marine biomass derived carbons have not been explored extensively. S and N double-doped porous carbons were obtained from a marine biomass related precursor. Adding carbon nanoparticles (CNP) graphene oxide (GO), or carbon nanotubes (CNTs), in an early stage of the synthesis leads to a modified porous texture and surface chemistry. The carbons retained 2-4.5 at% nitrogen and 1.1 at% sulfur. The best GO and CNT added carbons had an apparent surface area 1780 m2/g and 1170 m2/g, respectively, compared to 1070 m2/g of the CNP-free matrix. The Dubinin-Radushkevich (DR) and Henry models were used to assess the strength of the interactions between various gases and the surface. The N2/H2 and CO2/CH4 selectivities were estimated with ideal adsorbed solution theory (IAST). While the CNPs, particularly GO, had a remarkable effect both on the porous texture and the surface chemistry, their influence on selectivity is more modest.

Diethyldithiocarbamate (DDTC) has been employed in the sulfide ore flotation process, due to its excellent collection performance. Herein, we investigated the interfacial adsorption behavior of DDTC on four mineral phases of high-sulfur residue — sulfur, pyrite, sphalerite and lead sulfate. The adsorption behavior — adsorption structure and energy and electron localization function cross section — of DDTC and H2O were explored using density function theory calculation. The result was helpful to construct a co-adsorption model of DDTC and H2O, which was validated by the pure minerals flotation operation and the characterization of fourier transform infrared spectra. The co-adsorption model indicated that the DDTC adsorption on the sulfur, sphalerite and lead sulfate was weak with physical bonding, while its adsorption on the pyrite was strong with chemical bonding. Practical bench-scale operation of high-sulfur residue flotation was performed, whose result was different from that obtained from the pure mineral flotation. To explain the difference, our developed model predictions and the mineral fugacity pattern analysis on the high-sulfur residue flotation were synergistically used. Overall, this work first proposed the co-adsorption model of DDTC and H2O and provided important insights into the interfacial adsorption in the high-sulfur residue flotation.

This research is mainly focused on the evaluation of TiO2/Fe2O3 composite and two industrial types of waste (kaolin (Clay-K) and a blast furnace sludge (BFS)) as adsorbent materials of cyanide and as photocatalysts. First, adsorption tests were performed in the absence of light. During photodegradation experiments, the effect of the type of irradiation (ultraviolet (UV) light), visible light and natural sunlight), irradiation time, the type of photocatalyst, as well as irradiance in case of natural sunlight use, were investigated. Adsorption results indicate that Clay-K and TiO2/Fe2O3 materials adsorb approximately twice as much cyanide compared to the BFS sample, which only adsorbs 33.3% (124.87 mg/g); this is due to its smaller specific surface area (5.69 m2/g) compared to that of the other two materials (Clay-K and TiO2/Fe2O3 (14.93 m2/g and 66.59 m2/g, respectively). The results obtained from the study of photodegradation of cyanide under UV irradiation, indicate that Clay-K and BFS samples photodegrade cyanide by 96.44% and 92.66%, respectively. On the other hand, using UV irradiation plus solar irradiation and visible plus solar irradiation, the best photocatalyst was the TiO2/Fe2O3, with 98.66% photodegradation. The use of natural sunlight (irradiance of 600 to 800 W/m2) of a NaCN solution of 750 mg/L, the BFS material was the most efficient to photodegrade cyanide, obtaining 97% in two hours and 87% in just 30 minutes of irradiation.

Ammonia known as harmful gas that could impact on health and environment. Typically, ammonia gas emitted by fertilizer industry, rubber factory, etc. There are many options for advance industry to control ammonia gas pollution, absorption tower using water scrubber and using activated carbon as adsorption reaction could be an option. But for middle- and lower-class industry, it is common in Indonesia, as seen on many rubber factories, ammonia gas pollution is serious problem to control, actually they have used wet scrubber but eficiency is lower about 47%. This study measure performance for ammonia elimination as gas pollutant using absorption tower and adsorption tower in laboratory scale. Using electrochemical gas sensor, we measure both ammonia concentration for inlet and outlet simultaneously to settle saturation point of these two types of ammonia emission control. In conclusion, Ammonia absorbed in water proportional to saturation time and absorbent volume. Highest absorbed ammonia concentration 1.538 mg/L on 4000 mL absorbent. For Adsorption system, saturation time proportional and correlated to adsorbent weight and Adsorption capacity reverse correlated to adsorbent weight. Optimum adsorption point can be achieved from intersection curve between saturation time and adsorption capacity which is 1200 grams adsorbent

New materials are obtained by transforming fly ash wastes into a valuable composite, with tandem adsorption and photodegradation properties. Mild hydrothermal synthesis, from titanium dioxide, Platinum nanoparticles and zeolite materials obtained from a waste, fly ash, as support, was involved in the composite preparation. The Platinum nanoparticles extended the photocatalytic activity of the composite in Visible range (Eg = 2.1 eV). The efficiency of tandem adsorption and photocatalytic activity of the new composite were evaluated to 80.70% for Bemacid Blau and 93.89% for Bemacid Rot, after 360 min, the irradiation time, with H2O2 addition.

Two ligands, 1, 3-bis(4-carboxyphenyl)imidazolium chloride and 4, 4՛-bipyridine, were employed to prepare nickel and zinc azolium based MOFs, 1 and 2 by the mixed ligand solvothermal approach. The positively charged azolium moieties in the imidazolium linker resulted in a charged environment in the as-synthesized frameworks. As a result, 1 and 2 demonstrated preferential adsorption of CO2 over methane molecules in the gas phase adsorption due to the higher quadruple moment of CO2, which interacts more with the positively charged frameworks. Besides, in aqueous media, 1 and 2 exhibited incredible adsorption efficiency for anionic dyes. In the following, MOF 1 was metallated at the carbene site of the azolium linker to generate the novel heterogeneous catalyst 1-Pd, which was successfully applied for Sonogashira and Suzuki-Miyaura coupling reactions without losing its activity after three cycles.

Carbon dioxide (CO2), a major greenhouse gas, capture and separation has recently become a crucial technological solution to reduce atmospheric emissions from fossil fuel burning. Thereafter, many efforts have been put forwarded to reduce the burden on climate change by capturing and separating them especially from larger power plants by the utilization of different technologies. Those technologies have often suffered from high operating cost and huge energy consumption. On right side, physical process such as adsorption is very cost effective process which have been widely used to adsorb different contaminants including CO2. Henceforth, this review covers the overall efficacies of CO2 capture by the utilization of carbon based materials through adsorption technology. Subsequently, we also address the associated challenges and future opportunities of carbon based materials (CBMs). For CO2 capture, it was found that CBMs followed the order of carbon nanomaterials (i.e., graphene, graphene oxides, carbon nanotubes and their composites) < mesoporous -microporous or hierarchical porous carbons < biochar and activated biochar < activated carbons.

In this investigation magnetic γ-Al2O3 ceramic nanocomposite particles bearing epoxide functionality are prepared following a multistep process. The ultimate nanocomposite particles are named as γ-Al2O3/Fe3O4/SiO2/poly(glycidyl methacrylate (PGMA). The surface property is evaluated by carrying out the adsorption study of Remazol navy (RN), a model reactive azo dye, on both γ-Al2O3/Fe3O4/SiO2 and γ-Al2O3/Fe3O4/SiO2/PGMA nanocomposite particles. The adsorption is carried out at the point of zero charge (PZC) to neutralize the effect of particle surface charge. The adsorption rate is very fast, reached equilibrium (qe) value within five min. Due to mesoporous structure of silica layer γ-Al2O3/Fe3O4/SiO2 nanocomposite particles possessed relatively higher specific surface area and magnitude of adsorption is dependent on the total specific surface area. The introduction of epoxide functionality favored high adsorption capacity in mass per unit surface area. The adsorption process strictly followed Langmuir model. Thermodynamic equilibrium parameters implied that irrespective of surface functionality the adsorption process is spontaneous and exothermic. Pseudo-second-order rate kinetic model is more appropriate to explain the adsorption kinetics.

The Langmuir isotherm is a widely used model for analyzing adsorption equilibrium data. This study evaluated the efficiency and accuracy of all four linear forms of the Langmuir isotherm and its non-linear form using 67 experimental data sets selected from the literature. The results showed that only if all four linear forms simultaneously show high accuracy, then the non-linear form also shows high accuracy, and therefore it can be said that the process probably follows the Langmuir isotherm. On the contrary, when at least one of the four linear forms of the Langmuir isotherm has low accuracy, it means that the non-linear form also has low accuracy, and it can be concluded that this process does not follow the Langmuir isotherm. This research suggests that all four linear forms of the Langmuir isotherm should be evaluated simultaneously to conclude whether the studied system follows the Langmuir isotherm or not. In other words, relying on only one of the four linear forms of the Langmuir isotherm to model adsorption and calculate the Langmuir constant and maximum adsorption capacity is an incomplete approach, contrary to the conventional approach.

The dynamic interaction between carbon nanodots (CNDs) and cannabidiol (CBD) has captured significant attention as an innovative avenue for redefining drug delivery and amplifying therapeutic effectiveness. This in-depth review delves into the intricate synergy between these two elements, unveiling their profound potential in medicine. Commencing with an examination of the unique characteristics of CNDs and the techniques governing their synthesis, we discuss their versatility as drug carriers, highlighting their invaluable role in advancing CBD delivery. Cannabidiol, a non-psychoactive compound sourced from cannabis, has emerged as a focal point for its diverse therapeutic attributes. Nevertheless, the limitations posed by its restricted bioavailability and susceptibility to degradation pose substantial hindrances to realizing its full potential. Here, we elucidate how the amalgamation of CBD with CNDs transcends these challenges. We delve into the mechanisms that underlie this synergy, such as the augmentation of solubility and the safeguarding of CBD against premature breakdown, providing an intricate analysis. We will also journey you through a comprehensive exploration of diverse CBD loading techniques onto CNDs, dissecting the realms of physical encapsulation, covalent bonding, and adsorption processes. In summation, the combination of CNDs and CBD presents an extraordinary opportunity to elevate therapeutic outcomes. This synergetic paradigm masterfully tackles pivotal challenges in drug delivery, thereby paving the path for pioneering medical solutions.

In this research, a novel collector cetyl trimethyl ammonium chloride (CTAC) was used to separate hematite from quartz via reverse flotation for the first time. Micro-flotation tests showed that CTAC had a strong ability to selectively collect quartz and a separation of hematite from quartz could be accomplished with a concentration of 0.00263 mmol/L CTAC. Zeta-potential measurements indicated that the positive CTAC+ species could selectively increase the surface potential of quartz, but it had rather a weak effect on the hematite surface. X-ray photoelectron spectroscopy (XPS) detection indicated that CTAC had a stronger binding affinity to oxygen sites on the surface of quartz than that of hematite, resulting in a large amount of CTAC predominantly adsorbed on quartz rather than hematite.

Initial periods of adsorption kinetics play an important role in estimating the initial adsorption rate and rate constant of adsorption process. Several adsorption processes rapidly occur, and the experimental data of adsorption kinetics under the initial periods can contain potential errors. The pseudo-second-order (PSO) kinetic model has been popularly applied in the field of adsorption. The use of the nonlinear optimization method to obtain the parameters of the PSO model can minimize error functions during modelling compared to the linear method. However, the nonlinear method has limitations in that it cannot directly recognize potential errors in the experimental points of time-dependent adsorption, especially under the initial periods. In this study, for the first time, the different linear types (Types 1–6) of the PSO model are applied to discover the error points under the initial periods. The result indicated that the fitting method using its linear equations (Types 2–5) is really helpful for identifying the error (doubtful) experimental points from the initial periods of adsorption kinetics. The imprecise points lead to low adjusted R2 (adj-R2), high reduced χ2 (red-χ2), and high Bayesian information criterion (BIC) values. After removing those points, the experimental data were adequately fitted with the PSO model. statistical analyses demonstrated that the nonlinear method must be used for modelling the PSO model because its red-χ2 and BIC were lower than the linear method. Type 1 has been extensively applied in the literature because of its very high adj-R2 (0.9999) and its excellent fitting to experimental points. However, its application should be limited because the potential errors from experimental points were not identified by this type. For comparison, the other kinetic models (i.e., pseudo-first-order, pseudo-nth-order, Avrami, and Elovich) are applied. The modelling result using the nonlinear forms of those models indicated that the fault experimental points from the initial periods were not detected.

Although there is a common physiological notion that the origin of the membrane potential is attributed to transmembrane ion transport, it is theoretically possible to explain its generation by the mechanism of ion adsorption. It was previously suggested that the ion adsorption mechanism led even to the potential formulas which are even identical to either the famous Nernst equation or Goldman-Hodgkin-Katz equation. Our further analysis shown in this paper indicates that the potential formula based on the ion adsorption mechanism leads to one equation which is the function of material surface charge density and the material surface potential. Furthermore, we confirmed that the equation holds in all the different experimental systems we studied. Although we have not succeeded in elucidating why such an equation is established, the equation appears to be the key equation governing the characteristics of the membrane potential regardless of the systems in question.

Current physiology attributes the mechanism of membrane potential generation to transmembrane ion transport, but ion adsorption could just as well play this fundamental role. The evidence shows that the ion adsorption mechanism accurately reproduces the experimentally measured membrane potential. The Goldman-Hodgkin-Katz equation (GHK eq.) and the Nernst equation (Nernst eq.) are the typical mathematical formulas representing the membrane potential in current physiology. However, the authors were able to show that the potential formulas by ion adsorption mechanism give identical results to GHK eq. and Nernst. eq. Our experimental and theoretical analyses suggest that there is a special relationship between the membrane potential and the membrane surface charge density, and this unique equation inevitably leads to the establishment of a GHK eq and/or a Nernst eq. The authors found that the unique equation is the foundation of thermodynamics “Boltzmann distribution”. Thus, the GHK eq. and the Nernst eq. are simply the natural consequence of thermodynamics from the view of the ion adsorption mechanism.

Hematite (-Fe2O3) with uniform hexagonal flakes morphology has been successfully synthesized using a combination of gelatin as natural template with F127 via hydrothermal method. The resulting hematite was investigated as adsorbent and photocatalyst for removal of ibuprofen as pharmaceutical waste. Hexagonal flake-like hematite was obtained following calcination at 500 oC with the average size was measured at 1-3 µm. Increasing the calcination temperature to 700 oC transformed the uniform hexagonal structure into cubic shape morphology. Hematite also showed high thermal stability with increasing the calcination temperatures, however, the surface area was reduced from 47 m2/g to 9 m2/g. FTIR analysis further confirmed the formation Fe-O-Fe bonds, and the main constituent elements of Fe and O were observed in EDX analysis for all samples. Fe2O3-G samples have an average adsorption capacity of 55-25.5 mg/g at 12-22% of removal efficiency when used as adsorbent for ibuprofen. The adsorption capacity was reduced with increasing the calcination temperatures due to the reduction of available surface area of the hexagonal flakes when transformed into cube. Photocatalytic degradation of ibuprofen using hematite flakes achieved 50% of removal efficiency meanwhile combination of adsorption and photocatalytic degradation further removed 80% of ibuprofen in water/hexane mixtures.

Melatonin is a hormone used for treating several disorders. However, its oral administration is problematic due to the variable absorption and extensive first-pass metabolism. The topical application of this drug does not present these disadvantages and can be used for therapeutic and skin protection purposes. The adsorption and release of melatonin in the montmorillonite clay was investigated experimentally and theoretically. The drug-clay interaction products were prepared and characterized, showing a modified and improved diffusion and release of melatonin. The crystal structure and spectroscopic properties of melatonin and melatonin-water-mineral materials were studied by molecular modeling, finding that the adsorption of this drug is energetically favourable, and the results were consistent with the experimental data. Ab initio molecular dynamics simulations with the metadynamics methodology showed the release of melatonin from the confined interlayer nanospace of montmorillonite to the liquid bulk water with a 20 kcal/mol free energy barrier.

The effects of mixing orders of tannic acid (TA), starch and α-amylase on the enzyme inhibition of TA were studied, including mixing TA with α-amylase before starch addition (order 1), mixing TA with pre-gelatinized starch before α-amylase addition (order 2) and co-gelatinizing TA with starch before α-amylase addition (order 3). It was found that the enzyme inhibition was always highest for order 1 because TA could bind with the enzyme active site thoroughly before digestion occurred. Both order 2 and 3 reduced α-amylase inhibition through decreasing binding of TA with the enzyme, which resulted from the non-covalent physical adsorption of TA with gelatinized starch. Interestingly, at low TA concentration, α-amylase inhibition for order 2 was higher than order 3, while at high TA concentration, the inhibition was shown with opposite trend, which arose from the difference in the adsorption property between the pre-gelatinized and co-gelatinized starch at the corresponding TA concentrations. Besides, both the crystalline structures and apparent morphology of starch were not significantly altered by TA addition for order 2 and 3. Conclusively, although a polyphenol may have an acceptable inhibitory activity in vitro, the actual effect may not reach the expected one when taking processing procedures into account.

Carbon sequestration via carbon capture and storage (CCS) method is one of the most useful methods to lower the CO₂ emission in the atmosphere. Ethylenediamine (EDA) and triethylenetetramine (TETA) modified mesoporous carbon (MC) has been successfully prepared as CO₂ storage materials. The effect of various concentrations of EDA or TETA added to MC as well as activated carbon (AC) on their CO₂ adsorption capacity were investigated using high purity CO₂ as feed and titration method to quantitatively measure the amount of adsorbed CO₂. The results showed that within 60 min adsorption time, MCEDA49 gave the highest CO₂ capacity adsorption (19.68 mmol/g), followed by MC-TETA30 (11.241 mol/g). The improvement of CO₂ adsorption capacity at low TETA loadings proved that the four amine functional groups in TETA gave advantages to CO₂ adsorption. TETA functionalized MC has a potential to be used as CO₂ storage materials as it is used at low concentration. Therefore, it is more benign and friendly to the environment.

The remarkable adsorption capacity of graphene derived materials has prompted their examination in composite materials suitable for deployment in treatment of contaminated waters. In this study, crosslinked calcium alginate – graphene oxide beads were prepared and activated by exposure to pH 4 by using 0.1M HCl. The activated beads were investigated as novel adsorbents for the removal of organic pollutants (Methylene Blue dye and the pharmaceuticals Famotidine and Diclofenac) with a range of physicochemical properties. Effects of initial pollutant concentration, temperature, pH and adsorbent dose were investigated and kinetic models were examined for fit to the data. Maximum adsorption capacities q_max obtained were 1334, 35.50 and 36.35 mg g^-1 for the uptake of Methylene blue, Famotidine and Diclofenac respectively. The equilibrium adsorption had an alignment with Langmuir isotherms while the kinetics were most accurately modelled using a pseudo- first –order and second order models according to the regression analysis. Thermodynamic parameters such as ΔG^◦, ΔH^◦ and ΔS^◦ were calculated and the adsorption process was determined to be exothermic and spontaneous.

Deep coal beds have been suggested as possible usable underground geological locations for carbon dioxide storage. Furthermore, injecting carbon dioxide into coal beds can improve the methane recovery. Due to importance of this issue, a novel investigation has been done on adsorption of carbon dioxide on various types of coal seam. This study has proposed four types of Gaussian Process Regression (GPR) approaches with different kernel functions to estimate excess adsorption of carbon dioxide in terms of temperature, pressure and composition of coal seams. The comparison of GPR outputs and actual excess adsorption expresses that proposed models have interesting accuracy and also the Exponential GPR approach has better performance than other ones. For this structure, R2=1, MRE=0.01542, MSE=0, RMSE=0.00019 and STD=0.00014 have been determined. Additionally, the impacts of effective parameters on excess adsorption capacity have been studied for the first time in literature. According to these results, the present work has valuable and useful tools for petroleum and chemical engineers who dealing with enhancement of recovery and environment protection.

To realize high response and selectivity gas sensor in detecting dissolved gases in transformer oil, in this study, the adsorption of four kinds of gases (H2, CO, C2H2 and CH4) on Pd-graphyne as well as the gas sensing properties evaluation were investigated. The energetically favorable structure of Pd doped γ-Graphyne was first studied, including the comparison of different adsorption sites and discussion of electronic properties. Then, the adsorption of these four molecules on Pd-graphyne was explored. The adsorption structure, adsorption energy, electron transfer and electron distribution, the band structure and density of states were calculated and analyzed. The results show that the Pd atom prefers to be adsorbed on the middle of three C≡C bonds and the band gap is smaller. The CO adsorption exhibits the largest adsorption energy and electron transfer and brings obvious change to the structure and electron properties to Pd-graphyne. Because of the conductance decrease after adsorption CO and acceptable recovery time at high temperature, the Pd-graphyne can be promising gas sensing materials to detect CO with high selectivity. This work offers theoretical support for the design of nanomaterials based gas sensor using novel structure for industrial application.

Selection of efficient corrosion inhibitors requires detailed knowledge regarding interaction mechanism, which depends on the type and amount of functional groups within the inhibitor molecule. Position of functional groups between different isomers is often overlooked but not less important since factors like steric hinderance may significantly affect the adsorption mechanism. In this study we have presented how different dihydroxybenzene isomers interact with aluminium alloy 5754 surface, reducing its corrosion rate in bicarbonate buffer (pH = 11). We have shown the highest inhibition efficiency among tested compounds belongs to catechol at 10 mM concentration, although differences were moderate. Utilization of novel impedance approach to adsorption isotherm determination allowed to confirm that while resorcinol chemisorbs on aluminium surface, catechol and quinol follows ligand exchange model of adsorption. Unlike catechol and quinol, the protection mechanism of resorcinol is bound to interaction with insoluble aluminium corrosion products layer and was only found efficient at concentration of 100 mM (98.7%). The aforementioned studies were confirmed with scanning electron microscopy and x-ray photoelectron spectroscopy analyses. There is a significant increase of the corrosion resistance offered by catechol at 10 mM after 24 h exposure in electrolyte: from 63 to 98%, with only negligible changes in inhibitor efficiency observed for resorcinol at the same time. However, in the case of resorcinol a change in electrolyte color was observed. We have revealed that the differentiating factor is the keto-enol tautomerism. The NMR studies of resorcinol indicate the keto form in structure in presence of NaOH, while the chemical structure of catechol does not change significantly in alkaline environment.

Hierarchical micro-/mesoporous graphitic carbon spheres (HGCS) with a uniform diameter of ~0.35 μm were synthesized by Fe-catalyzed graphitization of amorphous carbon spheres resultant from hydrothermal carbonization. The HGCS resultant from 3 h at 900 °C with 1.0 wt% Fe catalyst had high graphitization degree and surface area as high as 564 m²/g. They also exhibited high specific capacitance of 140 F/g at 0.2 A/g, good electrochemical stability with 94% capacitance retention after consecutive 2500 cycles. The graphitization degree of the HGCS contributed about 60% of their specific capacitance, and their specific capacitance per unit surface area was as high as 0.2 F/m² which was much higher than in the most cases of porous amorphous carbon materials reported before. In addition, the HGCS showed a high adsorption capacity of 182.8 mg/g for methylene blue (MB), which was 12 times as high as that in the case of carbon spheres before graphitization.

Thermal energy storage (TES) is a key technology to enhance the efficiency of energy systems as well as to increase the share of renewable energies. In this context, the present paper reports a literature review of the recent advancement in the field of adsorption TES systems. After a first introduction about different heat storage technologies, the adsorption TES working principle is explained and compared to the other technologies. Subsequently, promising features and critical issues at material, component and system levels are deeply analyzed and the ongoing activities to make this technology ready for marketing are introduced.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The high demand for lithium (Li) relates to clean renewable storage devices and the advent of electric vehicles (EVs). The extraction of Li ions from aqueous media calls for efficient adsorbent materials with various characteristics, such as good adsorption capacity, good selectivity, easy isolation of the Li-loaded adsorbent, and good recovery of the adsorbed Li ions. The widespread use of metal-based adsorbent materials for Li ions extraction relates to various factors: (i) the ease of preparation via inexpensive and facile templation techniques, (ii) excellent selectivity for Li ions in a matrix, (iii) high recovery of the adsorbed ions, and (iv) good cycling performance of the adsorbents. However, the use of nano-sized metal-based LISs is limited due to challenges associated with isolating the loaded adsorbent material from the aqueous media. Adsorbent granulation process employing various binding agents (e.g., biopolymers, synthetic polymers, and inorganic materials) affords functional particles with modified morphological and surface properties that support easy isolation from the aqueous phase upon adsorption of Li ions. Biomaterials (e.g., chitosan, cellulose, alginate, and agar) are of particular interest because their structural diversity renders them amenable to coordination interactions with metal-based LISs to form 3D microcapsules. The current review highlights recent progress in the use of biopolymer binding agents for the granulation of metal-based LISs, along with various crosslinking strategies employed to improve the mechanical stability of the granules. The study reviews the effects of granulation and crosslinking on adsorption capacity, selectivity, isolation, recovery, cycling performance and the stability of the LISs. Adsorbent granulation using biopolymer binders has been reported to modify the uptake properties of the bio-adsorbent materials to varying degrees, in accordance with the surface and textural properties of the binding agent. The review further highlights the importance of granulation and crosslinking for improving the extraction process of Li ions from aqueous media. This review contributes to manifold areas related to industrial application of LISs, as follows: 1) to highlight recent progress in the granulation and crosslinking of metal-based adsorbents for Li ions recovery, 2) to highlight the advantages, challenges, and knowledge gaps of using biopolymer-based binders for granulation of LISs, and finally, 3) to catalyze further research interest into the use of biopolymer binders and various crosslinking strategies to engineer functional adsorbent materials for application in Li extraction industry. Properly engineered extractants for Li ions are expected to offer various cost benefits in terms of capital expenditure, percent Li recovery, and reduced environmental footprint.

The physiological mechanism of membrane potential generation relies on the passage of mobile ions across the plasma membrane, which is selectively permeable to mobile ions. The existence of a membrane and the transport of ions across it are essential for the generation of membrane potential. However, a long-forgotten theory, Association-Induction hypothesis, asserts that the heterogeneous distribution of charges in space, due to ion adsorption, is the true cause of membrane potential generation. Using an artificial living cell model consisting of a viscous aqueous solution, the mechanism of membrane potential generation is restudied in this work. The results indicate that membrane potential can be generated even in the absence of a plasma membrane and that ion adsorption leading to a heterogeneous spatial charge distribution is an essential factor for membrane potential generation. Consequently, the authors invites people to reconsider the Association-Induction hypothesis as a genuine mechanism for generating membrane potential.

Cytokine adsorption can resolve different complications characteristic of transplantation medicine, such cytokine storm activation, blood immuno- and AB0- incompatibilities but can also be performed for the treatment of various life-threatening conditions, such as sepsis, acute respiratory distress syndrome (ARDS), and cardiogenic shock, all of which can contribute to adverse clinical outcomes during transplantation. After surgery, dysmetabolism and stress response limit successful graft survival and can lead to primary (PGD) or secondary graft dysfunction. In this clinical context, and given that a major problem in transplant medicine is that the demand for organs far exceeds the supply, a technological innovation such as a hemoadsoption system could greatly contribute to increasing the number of usable organ donors. The objectives of this review are to describe the specific advantages and disadvantages of the application of cytokine adsorption in the context of transplantation and also to examine, before and/or after organ transplantation, the benefits of addition of a complementary cytokine adsorption therapy protocol.

The Shitouping pluton in Jiangxi Province, southern China, hosts an ion-adsorption heave rare earth element (HREE) deposit identified by recently geological survey. This study reveals the HREE pre-enrichment mechanism during the magma-hydrothermal process of granitic bedrock based on the comprehensive study of zircon structure and composition. Zircon from the Shitouping pluton, composed of syenogranite and monzogranite, can be categorized into three types based on structure and compositions. The Type-1 zircons, the predominate type in monzogranite granite, are early magmatic zircons with prismatic crystals and bright oscillatory zoning. In contrast, the late magmatic-hydrothermal zircons (Type-2 and Type-3) are mainly occurred in the syenogranite. The Type-2 zircons occur as murky euhedral crystals crystallized in the late magmatic stage. The Type-3 zircons with irregular zoning and abundant mineral inclu-sions in BSE images are closely associated with Type-2 zircons, possibly formed via intense hy-drothermal alteration during the hydrothermal stage. The increase in Y/Ho ratios from Type-1 to Type-3 zircon indicates that the Shitouping syenogranites underwent magmatic to hydrothermal evolution. Compared with Type-1 and Type-2 zircons, Type-3 zircons exhibit the highest con-centrations of F and HREEs. The significant increase of HREE concentrations both in zircons and bulk-rock composition of syenogranite can be attributed to the introduction of HREE-rich fluids during magma evolution. Under this condition, the HREEs mainly hosted in fluorocarbonates, which can easily release HREE3+ to generate ion-adsorption deposits during the weathering process. Therefore, we propose that increase of HREE contents in zircon reflect the exsolution of HREE-rich fluids during the magma evolution, which is important factor controlling HREE en-richment in Shitouping syenogranites and further generation of ion-adsorption HREE deposits.

Osteoconductive granulated biopolymers (OGB) are used to restore the lost volume of the jaw bone. OGB is employed as a loose fraction and exhibits physical traits common to bulk mixtures. By removing air bubbles and industrial dust from the OGB fraction through special processing, more accessible spaces are left over for the adsorption of bone growth factors. The recipient site's biological environment alters the OGB fraction's physical characteristics. This is the cause of the OGB fraction's volume changing uncontrollably during the first three weeks following surgery. Predictive indicators for describing the physical processes of osteoconduction include the compaction coefficient and adsorption capacity. Taking into account the prognostic indicators of the dynamics of changes in the physical properties of the OGB fraction in the postoperative period, 3D planning of the bioengineered structure should be done. The OGB fraction's adsorption and drainage properties are optimized by raising the purity of OGB production and preparing the biopolymer for clinical studies.

The adsorption of proteins on polymer is widely used in biosensors. Here, molecular dynamics (MD) simulation was used to study the immobilization of angiotensin converting enzyme II (ACE2) with six initial orientations proposed on polystyrene (PS) at the ambient conditions of pH (4.5, 6, 7, 8, 9.5) and NaCl (0.01, 0.05, 0.1, 0.15, 0.2, 0.25 M). ACE2 immobilization under favorable ambient conditions was characterized by minimum distance (short), settlement time (fast), interaction energy (substantial) and protein configuration (stable). ACE2 orientations proposed in 0.15M NaCl were respectively preferable to (90, 0, 0), (0, 0, 0) and (0, 270, 0), (180, 0, 0) and (0, 90, 0), (90, 0, 0) at pH 4.5, 6, 7, 9.5. ACE2 immobilization was further evaluated at pH 7 by optimizing NaCl concentration. Its proposed orientations of (i) (0, 270, 0), (ii) (0, 0, 0) and (90, 0, 0), and (iii) (0, 90, 0) and (90, 0, 0) were preferable in 0.05, 0.1 and 0.2 M NaCl, respectively. The great significance of cubic-orientation settlement mode provides tangible improvement for the microfabrication of biochips for rapid diagnosis of severe acute respiratory syndrome coronavirus II (SARS-CoV-2).

Carbamazepine (CBZ) is one of the most common emerging contaminants released to the aquatic environment through domestic and pharmaceutical wastewater. Due to its high persistence through conventional degradation treatments, is considered a typical indicator for anthropogenic activities. This study tested the removal of CBZ through two different clay-based purification techniques: adsorption of relatively large concentrations (20-500 μmol L-1) and photocatalysis of lower concentrations (&lt;20 μmol L-1). The sorption mechanism was examined by FTIR measurements, exchangeable cations released, and colloidal charge of the adsorbing clay materials. Photocatalysis was performed in batch experiments under various conditions. Despite the neutral charge of carbamazepine, the highest adsorption was observed on negatively charged montmorillonite-based clays. Desorption tests indicate that adsorbed CBZ is not released by washing. The adsorption/desorption processes were confirmed by ATR-FTIR analysis of the clay-CBZ particles. A combination of synthetic montmorillonite or hectorite with low H2O2 concentrations under UVC irradiation exhibits efficient homo-heterogeneous photodegradation at μM CBZ levels. The two techniques presented in this study suggest solutions for both industrial and municipal wastewater, possibly enabling water reuse.

L-asparaginase (ASNase) is an aminohydrolase currently used in the pharmaceutical and food industries. Enzyme immobilization is an exciting option for both applications, allowing a more straightforward recovery and increased stability. High surface area and customizable porosity make carbon xerogels (CXs) promising materials for ASNase immobilization. This work describes the influence of contact time, pH, and ASNase concentration on the immobilization yield (IY) and relative recovered activity (RRA) using Central Composite Design methodology. The most promising results were obtained using CX with an average pore size of 4 nm (CX-4), reaching IY and RRA of 100%. At the optimal conditions, the ASNase-CXs biocomposite was characterized and evaluated in terms of kinetic properties and operational, thermal and pH stabilities. The immobilized ASNase onto CX-4 retained 71% of its original activity after six continuous reaction cycles, showed a good thermal stability at 37 °C (RRA of 91% after 90 min) and was able to adapt to both acidic and alkaline environments. Finally, the results indicated a 3.9-fold increase in the immobilized ASNase affinity for the substrate, confirming the potential of CXs as a support for ASNase and as a cost-effective tool for subsequent use in the therapeutic and food sectors.

Accurate prediction of the membrane potential by membrane theory is possible on the basis that the plasma membrane is selectively permeable to ions and that permeability determines the characteristics of the membrane potential. However, an experimental and artificial cell system with an impermeable membrane serving as a model plasma membrane has a non-zero membrane potential, and this potential generated across the membrane is somehow consistent with the potential characteristics predicted by the membrane theory, despite the impermeability of the membrane to ions. A long-forgotten theory, called the association-induction hypothesis (AIH), has emerged as a more plausible mechanism for generating the membrane potential than the membrane theory to explain this unexpected behavior. The AIH asserts that ion-selective membrane permeability is not necessary for the generation of the membrane potential, which is contrary to the membrane theory. Although such an idea is not easy to accept, the experimental results clearly suggest the correctness of the AIH.

The ubiquity of amino acids in carbonaceous meteorites has suggested that amino acids are widespread in the Universe, serving as a common class of components for the emergence of life. However, parameters for modeling amino acid polymerization at mineral–water interfaces remain limited, although the interfacial conditions inevitably exist on planets with surface liquid water. Here, we present a set of extended triple-layer model parameters for aspartate (Asp) and aspartyl-aspartate (AspAsp) adsorptions on ferrihydrite, anatase, and γ-alumina determined based on the experimental adsorption data. By combining the parameters with the reported thermodynamic constants for amino acid polymerization in water, the impacts of these minerals on Asp dimerization are calculable over a wide range of environmental conditions. It was predicted, for example, that ferrihydrite strongly increases the AspAsp/Asp equilibrium ratio in neutral to acidic pH; the ratio in the adsorbed state reaches 40% even from a low Asp concentration (0.1 mM) at pH 4. This percentage is approximately 5 × 107 times higher than that attainable without mineral (8.5 × 10–6%). Our exemplified approach enables us to screen wide environmental settings for abiotic peptide synthesis from a thermodynamic perspective, thereby narrowing down the geochemical situations to be explored for life’s origin on Earth and Earth-like habitable planets.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

In this work, we synthesized chitosan grafted-poly acrylic acid (CS-g-PA) through surface-initiated atom transfer radical polymerization (SI-ATRP). We also studied the adsorption process of copper and lead ions onto CS-g-PA surface. Adsorption equilibrium studies indicated pH 4.0 as the best pH for the adsorption process, while the maximum adsorption capacity for Pb2+ ions was 98 mg*g-1 and for Cu2+ was 164 mg*g-1, higher adsorption capacities than chitosan alone (CS), where Pb2+ was only 14.8 mg*g-1and Cu2+ was 140 mg*g-1, respectively. Furthermore, the adsorption studies indicated that Langmuir model describes all the experimental data. All these results suggest that the new CS-g-PA polymers had potential as adsorbent for hazardous and toxic metal ions produced by different industries.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

When wastewater containing methylene blue, a cationic dye is improperly treated or immediately dumped into the environment, it can degrade the quality of water bodies and contaminate the ecological environment. The removal of methylene blue from the aqueous solution is critical and urgent. The present work focuses on the use of maize stalk agricultural waste to prepare an adsorbent for the removal of cationic dye (methylene blue) from an aqueous solution. The prepared maize stalk biochar (MSB) was modified with MnO2 and the modified maize stalk biochar was characterized using Fourier transform infrared (FTIR) spectroscopy. Taguchi technique was employed to determine the optimum conditions for the removal of methylene blue (MB) dye from aqueous solution by MMSB. The factors were adsorbent dose (0.5, 1.0 and 1.5 g/100 mL), initial dye concentration (100, 200 and 300 mg/L), contact time (30, 60, 90 minutes) and pH (4, 6 and 8). Among the investigated process factors, adsorption efficiency was influenced by adsorbent dose and initial MB dye concentration. The optimum parameters were 1 g/100 mL adsorbent dose, 100 mg/L initial dye concentration, 60 minutes contact time and a pH of 8.0. This yielded a removal efficiency of 87.49% with adsorption capacity of 206.53 mg/g. The adsorption kinetics agreed with the pseudo-second-order (R2 of 0.999968) model and fitted a Langmuir isotherm (R2 of 0.9795) representing homogeneous monolayer chemisorption.

As the major greenhouse gas, CO2 gas emission has been noticeably increased over the past decades resulting in global warming and climate change. As a result, it is imperative to reduce the excess CO2 in the atmosphere to hold “the increase in the global average temperature to well below 2°C (ideally 1.5°C) above pre-industrial levels set by the Paris Agreement on climate change. Among many ways, CO2 capture technology is considered as the most promising technology among the available technologies. Porous materials such as carbons, silica, zeolites, hollow fibers, and alumina are widely used as CO2 sorbents. However, among the available porous sloid sorbents, porous silica-based materials grabbed a significant attention due to their unique properties including high surface area, pore volume, good thermal and mechanical stability, and low cost. Therefore, development of porous silica materials as a promising CO2 absorbent is a continuously expanding research area in the current moment. Herein, we aim to visualize a full picture of the porous silica-based materials for CO2 capture. This review presents a comprehensive study of existing CO2 capture techniques and highlights the recent progress of different porous silica materials and synthesis processes. CO2 adsorption capacities of unmodified porous silica materials are less effective as compared with functionalized silica materials. Various research activities have been reported about functionalization of pours silica using amine groups. Therefore, in this review, different synthesis routes of amine-functionalized porous silica materials, CO2 adsorption capacities, gas selectivity and reusability were discussed. Moreover, the research challenges associated with the porous silica materials and future research directions are summarized.

The substrate N1, N3, N5 -tris(2-hydroxyphenyl)benzene-1,3,5-tricarboxamide (Sensor A) was prepared in the reaction of 1,3,5-benzenetricarboxylic acid (trimesic acid) and o-aminophenol in ethanol. The prepared organic sensor fulfills the chemiluminescent requirements including luminophore, spacer, and suitable binding receptor that distress the probe's luminescent features, providing selective and sensitive detection of mercury and iron ions in aqueous solutions. The sensor selectively detects mercury and iron ions in a water matrix containing various metal ions including sodium, calcium, magnesium, zinc, and nickel. Strong and immediate binding was observed between mercury ions and the substrate at pH 7.0 with a binding affinity toward Hg (II) enhanced by nine folds higher than that observed for iron sensor binding affinity, which makes the substrate a distinctive luminescence sensor for mercury detection at ambient conditions. The sensor shows a linear response toward Hg (II) in the concentration range from 4.2 x 10-5 to 2.0 x 10-8 M with a limit of detection of 1.0 x 10-8 M. Further, Sensor A provides linear detection for iron ions in the range from 1.5 x 10-3 to 1.5 x 10-8 M. The measured adsorption capacity of Sensor A toward mercury ions ranged from 1.25 to 1.97 mg/g and the removal efficiency from water samples reached 98.8% at pH 7.0. The data demonstrate that Sensor A is an excellent probe for detecting and removing mercury ions from water bodies.

Knowledge of the interaction between inorganic and organic phosphates with soil minerals is vital for improving the soil P fertility. To achieve an in-depth understanding we combined adsorption experiments and hybrid ab initio molecular dynamics simulations to analyze the adsorption of common phosphates, i.e. orthophosphate (OP), glycerolphosphate (GP) and inositolhexaphosphate (IHP), onto the 100 surface plane of goethite. Experimental adsorption data per mol P-molecule basis fitted to the Freundlich model show the adsorption strength increases in the order GP &lt; OP &lt; IHP, and IHP adsorption being saturated faster followed by GP and OP. Modeling results show that OP and GP form stable monodentate (M) and binuclear bidentate (B) motifs with B being more stable than M, whereas IHP forms stable M and 3M motifs. Interfacial water plays an important role through hydrogen bonds and proton transfers with OP/GP/IHP and goethite. It also controls the binding motifs of phosphates with goethite. Combining both experimental and modeling results, we propose that the B motif dominates for OP, whereas GP forms M and IHP forms a combination of M and 3M motifs. The joint approach plausibly explains why IHP is the predominant organically bound P form in soil. This study could be considered as a preliminary step for further studies for understanding the mechanisms of how microbes and plants overcome the strong IHP–mineral binding to implement the phosphate groups into their metabolism.

The adsorption of carbon dioxide on amino silanes-functionalized MCM-41 and SBA-15 materials is reported. The functionalization of mesoporous silicas was made by post-synthesis method, by impregnation of 3-aminopropyltriethoxysilane. The obtained materials were characterized by X-ray diffraction, scanning and transmission electron microscopies, nitrogen adsorption-desorption and X-ray photoelectron spectroscopy measurements. The carbon dioxide adsorption capacities for the samples were carried out under ambient pressures. The obtained results evidenced that amino-silanes with a terminal amine (–NH₂) were functionalized through covalent coupling of this group on the surface of the channels in the ordered mesoporous silica, meaning that the amine is anchored on the surface of the bigger pores of the MCM-41 and SBA-15 support. For functionalized materials, the CO₂ adsorption capacity of the AMCM-41 increased from 0.18 to 1.1 mmol·g⁻¹, whereas for ASBA-15, it was from 0.6 to 1.8 mmol·g⁻¹. The Lagergren kinetic algorithms were applied in order to validate the obtained results, evidencing the enhanced carbon dioxide adsorption capacity and stability of the functionalized ordered mesoporous molecular sieves.

Prasinoviruses are large dsDNA viruses commonly found in aquatic systems worldwide, where they can infect and lyse unicellular prasinophyte algae such as Ostreococcus. Host susceptibility is virus strain-specific, but resistance of susceptible Ostreococcus tauri strains to a virulent virus arises frequently. In clonal resistant lines that re-grow, viruses are usually present for many generations, and genes clustered on chromosome 19 show physical rearrangements and differential expression. Here, we investigated changes occurring during the first two weeks after inoculation of viruses. By serial dilutions of cultures at the time of inoculation, we estimated the frequency of resistant cells arising in virus-challenged O. tauri cultures to be 10⁻³–10⁻⁴ of the inoculated population. Re-growing resistant cells were detectable by flow cytometry 3 days post-inoculation (dpi), visible re-greening of cultures occurred by 6 dpi, and karyotypic changes were visually detectable at 8 dpi. Resistant cell lines showed a modified spectrum of host-virus specificities and much lower levels of OtV5 adsorption.

Biomass is a widely distributed and renewable source of carbon. The main objective of this work is to produce an activated carbon from coconut shells with suitable characteristics to separate CO2 from biogas. The textural characterization of the adsorbent has been determined. Pure component adsorption isotherms of CO2 and CH4 at 30, 50 and 70 °C have been measured. Moreover, the performance of the produced activated carbon, as potential adsorbent for CO2 capture from a CO2/CH4 gas mixture has been evaluated under dynamic conditions in a purpose-built fixed-bed setup.

The determination of the specific surface free energy, specific properties and Lewis’s acid base of solid materials is of capital importance in many industrial processes such as adhesion, coatings, two dimensional films and adsorption phenomena. (1) Background: The physicochemical properties of many solid particles were characterized during the last forty years by using the retention time of injected well-known molecules into chromatographic column containing the solid substrates to be characterized. The obtained net retention time of the solvents adsorbed on the solid allowing the determination of the net retention volume directly correlated to the specific surface variables, dispersive, polar and acid-base properties. (2) Methods: Many chromatographic methods were used to quantify the values of the different specific surface variables of the solids. However, one found a large deviation between the different results. In this paper, one proposed a new method that quantify the specific free energy of adsorption as well as the Lewis’s acid-base constants of many solid surfaces. (3) Results: The new applied method allowed us to obtain the specific enthalpy and entropy of adsorption of polar model organic molecules on several solid substrates such as silica, alumina, MgO, ZnO, Zn, TiO2 and carbon fibers. (4) Conclusions: our new method based on the separation between the dispersive and polar free surface energy allowed to better characterize the solid materials.

Food processing and consumption involves multiple contacts between biological fluids and solid materials of processing devices of which steel is one of the most common. Due to complexity of these interactions, it is difficult to identify the main control factors in the formation of undesirable deposits on the device surfaces that may affect safety and efficiency of the processes. Mechanistic understanding of biomolecule-metal interactions involving food proteins could improve management of these pertinent industrial processes and consumer safety in food industry and beyond. In this work, we perform a multiscale study of formation of protein corona on iron surfaces and nanoparticles in contact with cow milk proteins. By calculating the binding energies of proteins with the substrate we quantify the adsorption strength and rank proteins by the adsorption affinity. We use a multiscale method involving all-atom and coarse-grained simulations as well as generation of 3D structures of the proteins for this purpose. Finally, using the adsorption energy results, we predict the composition of protein corona on iron nanoparticles and flat surfaces via a competitive adsorption model.

There is an urgent demand worldwide for the development of highly selective adsorbents and sensors of heavy metal ions and other organic pollutants. Within these environmental and public health frameworks, we are combining the salient features of clays and chelatant polymers to design selective metal ion adsorbents. Towards this end, the ion imprinting approach has been used to develop a novel nanohybrid material for the selective separation of Cu2+ ions in aqueous solution. The Cu2+-imprinted polymer/ montmorillonite nanocomposite (IIP/Mt) and non-imprinted polymer/montmorillonite nanocomposite (NIP/Mt) were prepared by radical photopolymerization process in the visible light. Ion imprinting was indeed important as the recognition of copper ions by IIP/Mt was significantly superior to that of NIP/Mt that is the nanocomposite synthesized in the same way but in the absence of Cu2+ ions. The adsorption process as batch study was investigated under the experimental condition affecting same parameters such as contact time, concentration of ions metals and pH. The adsorption capacity of Cu2+ ions is maximized at pH 5. Removal of Cu2+ ion achieved equilibrium within 15 minutes; the results obtained were found to be fitted by the pseudo-second order kinetics model. The equilibrium process was well described by the Langmuir isothermal model and the maximum adsorption capacity was found to be 23.6 mg/g.

Biohydrogen is a versatile energy carrier for the generation of electric energy from renewable sources. Hydrogenases can be used in enzymatic fuel cells to oxidize dihydrogen. The rate of electron transfer (ET) at the anodic side between the [NiFe]-hydrogenase enzyme distal iron-sulfur cluster and the electrode surface can be described by the Marcus equation. All parameters for the Marcus equation are accessible from DFT calculations. The distal cubane FeS-cluster has a three cysteine and one histidine coordination [Fe₄S₄](His)(Cys)₃ first ligation sphere. The reorganization energy (inner- and outer-sphere) is almost unchanged upon a histidine-to-cysteine substitution. Differences in rates of electron transfer between the wild-type enzyme and the all-cysteine mutant can be rationalized by a diminished electronic coupling between the donor and acceptor molecules in the [Fe₄S₄](Cys)₄ case. The fast and efficient electron transfer from the distal iron-sulfur cluster is realized by a fine-tuned protein environment which facilitates the flow of electrons. This study enables the design and control of electron transfer rates and pathways by protein engineering.

This comprehensive review explores recent advancements in heavy metal remediation techniques, focusing on the utilization of cellulose-silica composites and tailored surface modification techniques. We examine the synthesis strategies and properties of cellulose-silica adsorbents, highlighting their enhanced adsorption capacities and structural robustness for removing heavy metal pollutants from aqueous environments. The review investigates various surface modification approaches, including thiol-functionalization, amino acid grafting, and silane coupling agents, for optimizing the surface chemistry and morphology of cellulose-silica composites. Mechanistic insights into the adsorption processes and kinetics of modified adsorbents are discussed, along with considerations for optimizing adsorption performance under different environmental conditions. This review provides valuable perspectives on the development of effective adsorbent materials for sustainable heavy metal remediation applications.

Water pollution with dyes is a critical environmental issue because off the huge amount of dyes disbarred annually which cause severe damage for the ecosystem and human life. On the other hand, the core-shell based magnetic materials have showed amazing character for controlling the material synthesis with targeted structure to enhance the adsorptive-removal of pollutants. Herein, Fe3O4 core-TiO2/mesoSiO2 and Fe3O4 core-mesoSiO2/TiO2 double shell nanoparticles were prepared by first (R1) and second (R2) routes. The preparation procedure is controlled to prepare the magnetic core with further coating layers from silica and titania for the uptake of methylene blue from aqueous solutions. The reported adsorption capacities for R1-0.2, R1-0.4 and R2 samples were 46, 38 and 50 mg/g respectively at pH 6 after 80 min contact time form 50 ppm methylene blue solution. The adsorption process of methylene blue onto Fe3O4core-meso SiO2/TiO2 double shell was well fitted with the pseudo-second-order kinetic model and Freundlish isotherm which suggested the quick and multilayer adsorption mechanism. In addition, results of thermodynamic investigation indicated that the surfaces of Fe3O4 core-mesoSiO2/TiO2 and Fe3O4 core-TiO2/mesoSiO2 double shell exhibit spontaneous tendency to adsorb methylene blue from the aqueous solutions. These results will encourage the further application of Fe3O4 core-meso SiO2/TiO2 and Fe3O4 core-TiO2/meso SiO2 double shell for removal of other dyes and pollutants from wastewater.

Breakthrough curves for the adsorption of H2S using a metal-oxides mixture were predicted using the Bohart-Adams model of fixed bed adsorption. This mixture (ZnMn2O4+ZnO+Mn2O3) came from the processing of an urban waste as spent alkaline batteries were. The H2S adsorption experiments were carried out in a fixed-bed column at 20º C, and under various experimental conditions: gas flow rate, inlet H2S concentration and adsorbent dosage. Curves predicted by the model matched well with experimental data, providing data for the possible scale-up of the system. At the various experimental variables, the efficiency of the column, were also provided in the work. This investigation demonstrated the usefulness of a waste material, like spent alkaline batteries, to provide an adsorbent material to mitigate the problem of the presence of this harmful gas.

Carrageenan (car-), used in the pharmaceutical as well as food industry, is marine sulfated polysaccharides. The carrageenan blends (CB) of kappa (κ-), iota (ι-), and lambda (λ-) of 50/50 weight by weight are multipurpose and biocompatible hydrophilic polymers. They were subjected to adsorption of copper (Cu2+) ions. The aim of the study was to conduct extensive rheological and mechanical studies rendering them suitable for biological purposes. The rheology was conducted at various temperatures using a frequency curve, frequency sweep, loss modulus, and storage modulus analysis. Models of rheology like Ostwald, Bingham, and Modified Bingham models were utilized. The rheological results demonstrated non-Newtonian/pseudo-plastic behavior at various temperatures. The models of rheology demonstrated good flow properties and rheological performance of these materials. These materials could be exploited for their application in pharmaceuticals, food, and cosmetics. Thus, our study reflects that these CB can be safely exploited in the healthcare, pharmaceutical, and food industry. However, further studies should be conducted to evaluate their effectiveness in clinical studies.

Nowadays, there is extensive production and use of plastic materials for different industrial activities. These plastics, either from their primary production sources or through degradation processes of the plastics themselves, can contaminate the ecosystem with micro and nanoplastics. Once in the aquatic environment, these microplastics can be the basis for the adsorption of chemical pollutants, favoring that these chemical pollutants disperse more quickly in the environment and can affect living beings. Due to the lack of information on adsorption, three machine learning models (random forest, support vector machine, and artificial neural network) to predict different microplastic/water partition coefficients (log Kd) were developed using two different approximations (based on the number of input variables). The best-selected machine learning models present, in general, correlation coefficients upper than 0.92 in the query phase, which indicate that these type of models could be used for a rapid estimation of the absorption of organic contaminants on microplastics.

In this study, Li-Al-OH layered double hydroxide (LDH), which was prepared by solvent-free one-step mechanochemical reaction of LiOH and Al(OH)₃, was applied to remove boron from aqueous solution. Dry-grinding for 3 h at a rotational speed of 500 rpm, Li/Al molar 1/2 was the optimum condition to prepare highly crystalline of Li-Al LDH phase with no evident impure phases. Two milling products with Li/Al molar ratio at 1/2 and 2/2 were evaluated for boron adsorption. The results confirmed that Li/Al molar ratio 2/2 sample showed high boron adsorption capacity due to the physical adsorption of Li-Al-OH LDH and chemical synergism of phase gel Al(OH)₃. The adsorption isotherms, described by the Langmuir model, indicated maximum monolayer boron uptake capacity 45.45 mg/g, implying competitive adsorption capacity of the material in our experiment.

Metal-organic frameworks (MOFs) represent the largest class of materials among the crystalline porous materials ever developed and have attracted attention as core materials for separation technology. Their extremely uniform pore aperture and nearly unlimited structural and chemical characteristics have attracted great interest and promise in applying MOFs to adsorptive and membrane–based separations. This paper reviews the recent research and development of MOF membranes for gas separation. Strategies for polycrystalline membranes and mixed matrix membranes are discussed, with a focus on separation systems involving hydrocarbon separation and CO2 capture. Challenges and opportunities for the industrial deployment of MOF membranes are also be discussed, providing guidance for the design and fabrication of future high-performance membranes. The contributions of the underlying mechanism to separation performances, and the adopted strategies and membrane processing technologies for breaking the selectivity/permeability trade–off are discussed.

The combination of organic matter, iron oxide, and clay minerals is of great significance for the adsorption of copper ions (Cu). The purpose of this study is to explore the characteristics of Cu adsorption and laws governing Cu complexation to organic–inorganic, organic–clay mineral, and iron-oxide–clay mineral complexes in the sediments in the estuary of plateau fault and sinking lake——Dianchi Lake. In this study, Cu adsorption tests were performed on the three complexes, in order to study the kinetic behavior of adsorption, Langmuir and Freundlich isotherm models were used. The samples before and after adsorption were characterized via scanning electron microscope (SEM), Fourier infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Our results show that, the Freundlich isotherm models model was able to describe adsorbent behavior in comparison to the Langmuir models. During the Cu adsorption process, the iron-oxide–clay mineral complex is able to adsorb Cu, via coordination exchange, through the –OH contained therein. Organic-matter–clay mineral complexes bonded to the surfaces of clay minerals by replacing the hydroxyl groups with functional groups (carboxyl groups or phenolic hydroxyl groups) contained in the organic matter. Organic–inorganic composites then adsorbed Cu through the coordination exchange of –OH in the polar functional groups of alcohols, phenols, and carboxylic acids. The adsorption capacity of Cu in these three sediment complexes was observed to have the following order: organic–inorganic complex &gt; organic-matter–clay mineral complex &gt; iron-oxide–clay mineral complex. The semi-quantitative analysis results of Fourier Infrared Spectroscopy show that the organic matter (changes in the peak area of functional groups such as carboxyl groups) in the organic-inorganic composite material has an important effect on the amount of copper ions adsorbed by clay minerals.

This research illustrates modification of multi-walled carbon nanotubes (MWCNT) by ZrO2/Pb to construct nanocomposites (MWCNT/ZrO2/Pb-NCs) by simple precipitation technique and subsequently examine its ability for adsorption of Amido black (AB) and Eosin B (EB) dyes in binary system. The present nanocomposites investigation by FESEM, XRD, FTIR, and EDX analysis, reveal its as-synthesized crystalline nature with cubic morphology and average particle size 30–50 nm. The present nano-adsorbent represent high efficiency for AB and EB adsorption from aqueous solution, while dependency of variables including pH, initial concentration of dyes, contact time and MWCNT/ZrO2/Pb-NCs mass were analyzed by central composite design (CCD). The predicted maximum removal percentage was 95% removal for both dyes is consequence of adjustment of operational conditions at pH of 6.0; 0.05 g MWCNT/ZrO2/Pb-NCs; 15 min stirring at 15 mg L-1 for both dyes. The Langmuir as applicable for representation and description of reveal data of adsorption with adsorption capacity of 15.46 and 16.92 mg g-1 for AB and EB, respectively. Pseudo-first order model owing to its high correlation coefficient and closeness of experimental and theoretical data well represented behavior of corresponding adsorption system. Mechanism examination strongly proof high contribution of external mass transference as the main rate-controlling step. The successful regeneration of MWCNT/ZrO2/Pb-NCs suggested their usefulness in wastewater treatment and its ability of environmental management.

Wasted Green tuff powder produced by cutting Towada stone is recycled as environmental cleaning material. The optimum temperature for green tuff powder calcination to reduce the hydroxyl radical produced in hydrogen peroxide decomposition with ultraviolet light (UV) and no light. The green tuff calcined at 800 °C shows the large decomposition rate of hydrogen peroxide with no UV light when measured by using ESR. With UV light, the optimum temperature for calcinating the green tuff powder in order to reduce hydroxyl radical is also 800 °C. Next, the powder calcined at 800 °C is used to produce the tile by compression and heating, and then the formaldehyde adsorption rate was measured. The green tuff powder calcined at 800 °C showed a high adsorption rate, similar to that of the activated carbon. The tiles formed at 40 MPa and heated st 1100 °C were the strongest and also adsorbed formaldehyde. The adsorbed formaldehyde on the green tuff tile and powder might have a possibility to decompose by photocatalytic.

(1) Background: The research on the potential of regional food products, known for their rich bio-active compound content, could enhance human health in local populations. This is especially pertinent amid the Covid-19 pandemic and global trade disruptions; (2) Methods: The current study evaluated the physico-chemical composition using standard methods, antioxidant activity via DPPH, ABTS, FRAP, and CUPRAC methods, sorption capacity (at 10°C, 25°C, and 40°C with water activity ranging from 0.1 to 0.9) through the static-gravimetric method, and monolayer moisture content (MMC) calculated using the BET model; (3) Results: The approximate physi-co-chemical composition of laboratory-produced quince powder is as follows: proteins - 1.27g, carbohydrates - 75.80g, fats - 0.49g, fibers - 21.50g, ash – 2.31g, and nutritional value – 355.65kcal. Antioxidant activity is confirmed by all methods. The Modified Halsey model is recommended to describe the sorption isotherms with an S-shaped form. The MMC for the adsorption process ranges from 14.41% d.b. to 7.09% d.b., and for the desorption process, it ranges from 13.11% d.b. to 7.80% d.b.; (4) Conclusions: Seasonal and regional foods boast the best nutritional profiles, as they are cultivated and harvested at optimal ripeness in natural sunlight, preserving the essential vitamins and minerals in the food.

The chemical reaction of ion-adsorption type rare earth during in-situ leaching process is accompanied by ion migration and charge movement, making the leaching process electrochemical in nature. The chemical reaction rate plays an important role in the leaching rate of rare earth elements. In this work, electrochemical impedance spectroscopy (EIS) was used to reveal characteristics of electrical resistance alteration and leaching rate of rare earth elements during in-situ leaching. The equivalent circuit model of the leaching process was established, and two critical parameters of solution resistance Rs and charge transfer resistance Rt were analyzed to reflect the electrochemical characteristics. According to the characteristics of electrical resistance alteration, the leaching process was divided into four stages: wetting, reaction, equilibrium, and top water stage. The resistance parameters Rs and Rt decreased first and then increased during the leaching process. The maximum value of Rs was 1330Ω∙cm2 at the end of the top water stage, and the minimum value was 135Ω∙cm2 at the beginning of the equilibrium stage. The maximum value of Rt was 8310Ω∙cm2 at the beginning of the leaching stage, and the minimum value was 21Ω∙cm2 at the end of the reaction stage. Rs and Rt were negatively correlated with the pore size and chemical reaction rate during leaching. With increasing of pore size and reaction rate , the resistance parameter decrease. This study provide a new idea for intelligent monitoring of rare earth ore.

The physical properties of coal reservoirs are the main restrictions to exploration and development of CBM. The study of the physical characteristics of coal reservoirs and their controlling factors is of great significance to the safe and efficient development and utilization of CBM resources in the mining area. The Pingdingshan No. 10 coal mine was chosen for this study because of its better gas production effect at the test wells. The reservoir properties of the main coal seams of the No. 10 coal mine were tested and analyzed to comprehensively evaluate the reservoir properties. The results indicate that (1) The gas content and methane purity of the No. 4 coal seam are significantly higher than the No. 2 seam, and therefore they have better development potential than the No. 2 seam; (2) The average adsorption time of the No. 2 coal seam is less than that of the No. 4 seam, making it easier to reach the peak production capacity of CBM wells in the short term, but is not conducive to long-term stable production of CBM. The Langmuir volume of the No. 2 coal seam samples was significantly greater than for the No. 4 coal seam; however, the No. 4 coal seam contains about three times the amount of gas in the No. 2 seam; (3) All three coal seams have high porosity, which is favorable for large amounts of CBM adsorption and storage. Micropores predominate, transitional pores are less frequent, and a few mesopores occur; macropores are the least common. Samples from the No. 4 seam contained the highest proportion of micropores; (4) Organic pores were common in the all coal samples, with pore diameters not more than 30 µm, mainly concentrated between 50.5 and 1000 nm. Microfractures with aperture less than 70 nm were relatively frequent, mainly in the 50–65 nm range. A large number of the nanoscale microfractures were curved or jagged; (5) Fractures in the No. 2 and No. 4 coal seam samples with widths of 50 nm to 20 µm were more developed, and many were filled with kaolinite, quartz and other minerals; (6) The samples contained mostly layered silicate minerals (kaolinite), with hard granular minerals (quartz) next, and a very small quantity of iron-type minerals such as siderite and pyrite in dendritic form. The results of this study can provide a reference basis for the large-scale development and utilization of subsequent CBM wells.

The automotive industry is continuously seeking innovative solutions to improve the energy efficiency and sustainability of vehicles. Among the various energy-consuming systems in automobiles, air conditioning plays a crucial role. However, conventional vapour compression-based air conditioning systems are known for their high energy consumption and environmental impact. In recent years, adsorption technology has gained significant attention as a promising alternative due to its potential for higher energy efficiency and reduced greenhouse gas emissions. This review paper presents a comprehensive analysis of advancements in adsorption air conditioning technology specifically designed for automotive applications. The paper examines the recent research and development efforts in enhancing the performance and practicality of these systems, encompassing areas such as advanced materials selection, and system integration strategies. Furthermore, this review highlights the benefits and challenges associated with implementing adsorption air conditioning systems in vehicles. The environmental impact and potential for waste heat recovery are also discussed. Additionally, emerging trends, such as hybridization with conventional vapour compression systems, are explored to further optimize the energy efficiency and sustainability of automotive air conditioning. By critically evaluating the existing literature and research advancements, this review provides insights into the state-of-the-art thermally driven technologies for automotive applications.

Poly(vinyl butyral-co-vinyl alcohol-co-vinyl acetate) named further PVBA was investigated as protective coating for copper corrosion in 0.9 % NaCl solution using electrochemical measurements such as, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization associated with Atomic Force Microscopy (AFM). The PVBA coating on the copper surface (Cu-PVBA) was modeled in methanol containing PVBA. Its inhibitory properties against corrosion was comparatively discussed with those of the copper sample treated in methanol without polymer (Cu-Me) and of untreated sample (standard copper). A protective performance of PVBA coating of 80 % was computed from electrochemical measurements, for copper corrosion in NaCl solution. Also, AFM images designed a specific surface morphology of coated surface with PVBA, clearly highlighting a polymer film adsorbed on the copper surface, which presents certain deterioration after corrosion, but metal surface was not significantly affected compared to those of untreated samples or treated in methanol, in the absence of PVBA.

Leather waste was carbonized at 800 °C in inert atmosphere. The resulting biochar was coated in situ with polypyrrole nanotubes produced by the oxidation of pyrrole in the presence of methyl orange. The composites of carbonized leather with deposited polypyrrole nanotubes of various composition were compared with similar composites based on globular polypyrrole. Their molecular structure was characterized by infrared and Raman spectra. Both conducting components formed a bicontinuous structure. The resistivity determined by four-point van der Pauw method was monitored as a function of pressure applied up to 10 MPa. The typical conductivity of composites was of the order of tenths to units S cm−1 and it was always higher for polypyrrole nanotubes than for globular polypyrrole. The conductivity decreased by 1–2 orders of magnitude after treatment with ammonia but still maintained a level acceptable for applications operating under non-acidic conditions. The composites were tested for dye adsorption, viz. cationic methylene blue and anionic methyl orange, using UV-spectroscopy. The composites are designed for the future use as functional adsorbents controlled by the electrical potential.

In the field of construction, materials referred to as sustainable are currently undergoing a process of technological development. This study aims to contribute to the understanding of the behavior of the fundamental properties of concretes prepared with recycled coarse aggregates that incorporate in their matrix a polyethylene terephthalate-based additive in an attempt to reduce their high porosity. Techniques to measure the gas adsorption, water porosity and x-ray diffraction (XRD) were used to evaluate the effect of the additive on the physical, mechanical and microstructural properties of these concretes. Porosity reductions of up to 30.60% are achieved with the addition of 1, 3, 4, 5, 7 and 9% of the additive, defining a new state in the behavioral model of the additive (the overdosage point) in the concrete matrix; in addition, the porous network of these concretes and their correlation whit other physical and mechanical properties are also explained.

The requirements for efficient replacement of fossil fuel, combined with the growing energy crisis, put hydrogen production into focus. Efficient and cost-effective electrocatalysts are needed for H2 production, and novel strategies for their discovery must be developed. Here we utilized Kinetic Monte Carlo (KMC) simulations to demonstrate that hydrogen evolution reaction (HER) can be boosted via hydrogen spillover to the support when the catalyst surface is largely covered by adsorbed hydrogen under operating conditions. Based on the insights from KMC, we synthesized a series of reduced graphene oxide-supported catalysts and compared their activities towards HER in alkaline media with that of corresponding pure metals. For Ag, Au, and Zn, the support effect is negative, but for Pt, Pd, Fe, Co, and Ni, the presence of the support enhances HER activity. The HER volcano, constructed using calculated hydrogen binding energies and measured HER activities, shows a positive shift of the strong binding branch. This work demonstrates the possibilities of metal|support interface engineering for producing effective HER catalysts and provides general guidelines for choosing novel catalyst-support combinations for electrocatalytic hydrogen production.

Propolis, or bee glue, is a complex mixture of resins from plant buds and flowers, wax, pollen and bee saliva. It also contains various vitamins, essential oils, mineral salts, trace elements, hormones and enzymes. It has been found that propolis possesses antimicrobial, antiviral and anti-inflammatory properties. We have studied the antiviral activity of six extracts of Bulgarian propolis collected from six districts of Bulgaria. The study was conducted against structurally different viruses: Human coronavirus strain OC-43 (HCoV OC-43) and Human respiratory syncytial virus type 5 (HRSV-5) (enveloped RNA viruses), Human herpes simplex virus type 1 (HSV-1) (enveloped DNA virus), Human rhinovirus type 14 (HRV-14) (non-enveloped RNA virus) and Human adenovirus type 2 (HadV-2) (non-enveloped DNA virus). The influence of the extracts on the internal replicative cycle of viruses was determined using the cytopathic effect (CPE) inhibition test. The virucidal capacity, their influence on the adsorption stage and their protective effect on uninfected cells were also determined by the end-point dilution method. Residual viral infectivity in propolis samples was compared to untreated controls and Δlgs were calculated. When administered during viral replication, most propolis extracts demonstrated the strongest activity against HCoV OC-43. The influence of propolis extracts on the viability of extracellular virions was expressed to a different degree in the various viruses studied, and the effect was significantly stronger in those with an envelope. Almost all extracts significantly inhibited the step of herpes virus adsorption to the host cell, and some of them showed a protective effect on healthy cells before they were subjected to herpes infection. Our results enlarge the knowledge about the action of propolis and could open new perspectives for its application in viral infections treatment.