Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

The cubic nonlinearity of graphene oxide (GO) monolayer was characterized by open and closed Z-scan using a nano-second laser of 10 Hz repetition rate with a Gaussian spatial beam profile. The reverse saturable absorption or positive nonlinearity from open Z-scan and valley-peak traces or positive nonlinearity from closed Z-scan was displayed. The reverse saturable absorption could be from a two-photon or two-step excitation process due to the larger absorption in the lower visible and upper UV wavelength region compared with the excitation source. The nonlinear absorption and nonlinear refraction coefficient were estimated to be ~ 2.62x10-8 m/W and 3.9x10-15 m2/W, respectively. This study also reveals the effect of nonlinear absorption on nonlinear refraction traces.

The dynamics of a spherical particle in an asymmetric serpentine is studied by finite element method (FEM) simulations in a physically unconstrained system. The two-way coupled time dependent solutions illustrate the path of the particle along a curve where a secondary flow (Dean flow) has developed. The simulated conditions were adjusted to match those of an experiment for which particles were focused under inertial focusing conditions. The obtained rotational modes allowed to infer the influence of the local flow around the particle. We propose a new approach to find the decoupled secondary flow contribution employing a quasi-Stokes flow.

In this study novel recommendations are presented and substantiated for selecting the number of modes and optical thicknesses of flat lattice slabs that make up the microreliefs, which minimize the computational complexity of the rigorous coupled-wave analysis calculation of the diffraction efficiency (DE) of a sawtooth two-layer two-relief microstructure, while maintaining the specified reliability of the calculation results. The computational complexity can be controlled by allowing one or another level of oscillation of the DE curves depend on the angle of incidence of the radiation incident on the microstructure. In particular, the complexity of the multi-thousand DE calculations in the optimization process can be reduced by using the proposed methodology as well as increased computational complexity to certify the accuracy of the solution obtained as a result of implemented optimization.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

In this work, the possibility of fabrication magneto-optical ceramics by vacuum sintering of compacts prepared by electrophoretic deposition (EPD) from suspensions of (Ho0.95La0.05)2O3 (HoLa) nanopowders made by self-propagating high-temperature synthesis and (Y0.9La0.1)2O3 (YLa) nanopowders made by laser synthesis was systematically investigated. The processes of the formation of bulk one- and two-layer compacts by the EPD method from non-aqueous suspensions of nanopowders was studied. The use of acetylacetone and polyvinyl butyral (PVB) was shown to make it possible to obtain stable alcohol suspensions of the nanopowders characterized by high zeta potential values (+29…+80 mV) and to carry out a stable EPD process. One-layer compacts were made from the YLa and HoLa nanopowders with a density of 30–43%. It was found out that the introduction of PVB into the suspension leads to a decrease in the mass and thickness of the green bodies deposited, but does not significantly affect their density. A possibility to make two-layers (YLa/HoLa) compacts with a thickness of up to 2.6 mm and a density of up to 46% was demonstrated. Sintering such compacts in a vacuum at a temperature of 1750°C for 10 hours leads to the formation of ceramics with a homogeneous boundary between the YLa/HoLa layers and thickness of the interdiffused ions layer of about 30 μm.

Whether there is any inclination between structures and functions of antimicrobial peptides (AMPs) is a mystery yet to be unraveled. AMPs have various structures associated with many different antimicrobial functions, including antibacterial, anticancer, antifungal, antiparasitic and antiviral activities. However, none has yet reported any antimicrobial functional tendency within a specific category of protein/peptide structures nor any structural tendency of a specific antimicrobial function with respect to AMPs. Here we examine the relationships between structures categorized by three structural classification methods (CATH, SCOP and TM) and seven antimicrobial functions with respect to AMPs using an enrichment analysis. The results show that antifungal activities of AMPs were tightly related to two-layer sandwich structure of CATH, knottin fold of SCOP, and the first structural cluster of TM. The associations with knottin and TM cluster 1 even sustained through the AMPs with a low sequence identity. Besides, another significant mutual enrichment was observed between the third cluster of TM and anti-gram-positive-bacterial/anti-gram-negative-bacterial activities. The findings of the structure-function inclination further our understanding of AMPs and could help us design or discover new therapeutic potential AMPs.

This study reports the development of a numerical method to simulate two-phase flows of Newtonian fluids that are incompressible, immiscible, and isothermal. The interface in the simulation was located and reconstructed using the geometric volume of fluid (VOF) method. The implementation of the Piecewise-Linear Interface Calculation (PLIC) scheme of the VOF method was performed to solve the three-dimensional (3D) interface transport during the dynamics of two-phase flows. In this method, the interface is approximated by a line segment in each interfacial cell. The balance of forces at the interface was accounted for using the continuum interfacial force (CSF) model. To solve the Navier-Stokes equations, meshless finite difference schemes from the HiG-Flow computational fluid dynamics software were employed. The 3D PLIC-VOF HiG-Flow algorithm was used to simulate several benchmark two-phase flows for the purpose of validating the numerical implementation. First, the performance of the PLIC implementation was evaluated by conducting two standard advection numerical tests: the 3D shearing flow test and the 3D deforming field test. Good agreement is obtained for the 3D interface shape using both the 3D PLIC-VOF HiG-Flow algorithm and those found on the scientific literature. In addition, the absolute error of the volume tracking advection calculation obtained by our 3D PLIC-VOF HiG-Flow algorithm was found to be smaller than the one found in the scientific literature for both the 3D shearing and 3D deforming flow tests. Lastly, the 3D bubble rising problem was simulated for different fluid densities and viscosity’s ratios. Again, good agreement is obtained for the 3D interface shape using both the newly implemented algorithm and the OpenFOAM, DROPS and NaSt3D software. The bubble’s rise velocity and evolution of the bubble’s center of mass is also computed with the 3D PLIC-VOF HiG-Flow algorithm and found to be in agreement with these software.

The power generation structure and load characteristics in different provinces are quite different in China, and the distribution of peak regulating resources and demands is extremely unbalanced. Due to many factors such as low power marketization degree, shortage of peak regulating resources and block of transmission channels, the consumption of new energy is facing greater pressure. In order to improve the mutual aids in regional power grid, this paper proposes a two-layer optimization dispatching model considering the mutual aids of peak regulation resources between each province, and determines the optimal units startup mode and power output in each provinces, thus obtaining all the power supply output arrangements and the technical and economic indicators. Finally, take the actual regional power grid in China as an example, the simulation results show that the proposed model can significantly improve the new energy utilization rate, which verified the effectiveness and feasibility of the proposed model and methods in this paper.

This paper considers a two-way relay network, where two source nodes exchange messages through several relays in the presence of an eavesdropper, and the channel state information (CSI) of the eavesdropper is imperfectly known. The amplify-and-forward relay protocol is used and the relay beamforming weights are designed. The model is built up to minimize the total relay transmit power while guaranteeing the quality of service at users and preventing the eavesdropper from decoding the signals. Due to the imperfect CSI, a semi-infinite programming problem is obtained. An algorithm is proposed to solve the problem, and the iterative points are updated through the linesearch technique, where the feasibility are preserved during iterations. The optimality property is analyzed. The obtained subproblems are quadratic constrained quadratic programming problems, either with less than $4$ constraints or with only one variable, which are solved optimally. Simulation results demonstrate the importance of the proposed model, and imply that the proposed algorithm is efficient and converges very fast, where more than 85% of the problems are solved optimally.

The fluid seepage in local-saturated zone of subgrade promotes the migration of fine particles in the filler, resulting in the change of pore structure and morphology of the filler and the deformation of solid skeleton, which affects the fluid seepage characteristics. Repeatedly, the muddy interlayer, mud pumping and other diseases are finally formed. Based on the theory of two-phase seepage, the theory of porous media seepage, and the principle of effective stress in porous media, a two-phase fluid-solid coupling mathematical model in local-saturated zone of subgrade considering the effect of fine particles migration is established. The mathematical model is numerically calculated with the software COMSOL Multiphysics○R, the two-phase seepage characteristics and the deformation characteristics of the solid skeleton in local-saturated zone of the subgrade are studied. The research results show that due to the continuous erosion and migration of fine particles in local-saturated zone of the subgrade, the volume fraction of fine particles first increases then decreases and finally becomes stable with the increase of time. And the volume fraction of fine particles for the upper part of the subgrade is larger than that for the lower part of the subgrade. The porosity, the velocity of fluid, the velocity of fine particles, and the permeability show a trend of increasing first and then stabilizing with time; the pore water pressure has no significant changes with time. The vertical displacement increase first and then decrease slightly with the increase of time, and finally tend to be stable. For a filler with a larger initial volume fraction of fine particles, the maximum value of the volume fraction of fine particles caused by fluid seepage is larger, and the time required to reach the maximum value is shorter. It can be concluded that in actual engineering, the volume fraction of fine particles in the subgrade filler should be minimized on the premise that the filler gradation meets the requirements of the specification.

The behavior of convective boundary conditions is studied to delineate their role in heat and mass relegation in the presence of radiation, chemical reaction, and hydromagnetic forces in three-dimensional Powell-Eyring nanofluids. Implications concerning non-Fourier’s heat flux and non-Fick’s mass flux with respect to temperature nanoparticle concentration were examined to discuss the graphical attributes of the principal parameters. An efficient optimal homotopy analysis method is used to solve the transformed partial differential equations. Tables and graphs are physically interpreted for significant parameters

The paper proves the existence of a family of axisymmetric equilibrium figures as solutions of a stationary problem with unknown boundaries for the Navier–Stokes equations corresponding to the slow rotation of a viscous compressible two-layer liquid mass about some axis. It is assumed that the liquids are barotropic, capillary and have different viscosities, the internal fluid being bounded by a closed surface. This interface does not intersect with the external boundary of the cloud. The proof is based on implicit function theorem and carried out in the Hölder spaces.

Given of the outstanding versatile properties, the multilayered anti-corrosion coatings have drawn great interests in academic and engineering fields. However, the application of multilayered coatings is restricted by some limitations such as low interlayer compatibilities, harsh preparation process, etc. This work introduced a composite film fabricated on 2A12 aluminum alloy surface, including an anodic oxide film, a sol-gel film as well as a layer-by-layer (LBL) self-assembling film from bottom to top. The microstructure and elemental characterization indicated that the finish of the coating with the LBL film resulted in a closely connected multilayered coating with a smoother surface. The anticorrosion performance was systematically evaluated in the simulated corrosive medium and neutral salt-spray environment. The intergrated coating with the LBL film presented an excellent anticorrosion ability with the system impedance over 108 Ω•cm² and the self-corrosion current density two orders of magnitude lower than that of the other coatings. After the acceleration test in salt-spray environment, the multilayered coatings could still show a good protective performance with almost no cracks and no penetration of chloride ions. It is believed that the as-constructed multilayered coating with high corrosive properties and fine surface state will have promising applications in the field of anticorrosion engineering.

The modulation instability of surface capillary-gravity water waves is analysed in a shear flow model with a tangential discontinuity of velocity. It is assumed that air blows along the surface of the water with a uniform profile in the vertical direction. Such a model, despite its simplicity, plays an important role in hydrodynamics as the reference model for investigating basic physical phenomena of wave-current interactions and acquiring insights into a series of complex phenomena. In certain cases where the wavelength of interfacial perturbations is much bigger than the width of the shear fow profile, the model with the tangential discontinuity in the velocity is adequate for describing physical phenomena at least within limited spatial and temporal frameworks. A detailed analysis of the air-flow conditions under which modulation instability sets in is presented. It is also shown that the interfacial waves are subject to dissipative or radiative instability when negativeenergy waves appear at the interface.

The study was conducted in coniferous and deciduous old growth forests in two forest complexes located in: i) the fenced area of the Popielno Research Station of the Polish Academy of Sciences, with free-living Polish pony [Polish primitive horse (Equus ferus caballus)], and ii) open Maskulińskie Forest District managed (harvested) forest, without horses. The impact of forest animals on ground cover layer as well as on understory shrub layer and undergrowth, in i) area (horses and other forest animals) was compared with the results in ii) area (forest animals without horses). Very significant differences in the understory and undergrowth (above 0,5 m) layer vegetation communities structure between both areas and type of stands were found. The results suggest that the presence of the Polish horse substantially changed the species composition and increased the species diversity of the ground layer and shrub layer both on coniferous forest and in the deciduous forest habitats. The height of the shrub layer trees was lower by 30% in the area with the Polish horse.

Building deep learning models proposed by third parties can become a simple task when specialized libraries are used. However, a great deal of mystery still surrounds the design of new models or the modification of existing ones. These tasks require in-depth knowledge of the different components or building blocks as well as their dimensions. This information is limited and broken up in different literature. In this article, we collect and explain in-depth the building blocks to design deep learning models, starting from the artificial neuron to the concepts involved in building deep neural networks. Furthermore, the implementation of each building block is exemplified using the Keras library.

In this paper we introduce the New/Generalized two parameter Gamma function and Pochhammer symbol. We named them, as Generalized p - k Gamma Function and Generalized p - k Pochhammer symbol and denoted as $ _{p}^{a}\Gamma_{k}(x) $ and $ _{p}^{a}(x)_{n,k} $ respectively. We prove the several identities for $ _{p}^{a}\Gamma_{k}(x) $ and $ _{p}^{a}(x)_{n,k} $ those satisfied by the classical Gamma function. Also we provide the integral representation for the $ _{p}^{a}\Gamma_{k}(x) $

This paper reviews the unilateral and bilateral, one- and two-dimensional Laplace transforms. The unilateral and bilateral Laplace transforms are compared in the one-dimensional case, leading to the formulation of the initial-condition theorem. This problem is solved with all generality in the one- and two-dimensional cases with the bilateral Laplace transform. General two-dimensional linear systems are introduced and the corresponding transfer function defined.

From experimental studies of protein folding, it is now clear that there are two types of folding behavior, i.e., two-state folding and non-two-state folding, and understanding the relationships between these apparently different folding behaviors is essential for fully elucidating the molecular mechanisms of protein folding. This article describes how the presence of the two types of folding behavior has been confirmed experimentally, and discusses the relationships between the two-state and the non-two-state folding reactions, on the basis of available data on the correlations of the folding rate constant with various structure-based properties, which are determined primarily by the backbone topology of proteins. Finally, a two-stage hierarchical model is proposed as a general mechanism of protein folding. In this model, protein folding occurs in a hierarchical manner, reflecting the hierarchy of the native three-dimensional structure, as embodied in the case of non-two-state folding with an accumulation of the molten globule state as a folding intermediate. The two-state folding is thus merely a simplified version of the hierarchical folding caused either by an alteration in the rate-limiting step of folding or by destabilization of the intermediate.

This research work deals with the formulation of numerical scheme with algorithm to compute singularly perturbed partial differential equations(SP-PDEs) involving a significant negative shift. The problem involves small parameter which causes a rapidly changing boundary layers in the vicinity of a body, and the negative shift term causes interior layer. Such appearance of an abruptly varying layers causes difficulties to find the exact solution and it is not adequate to employ classical numerical methods. The technique presented in this research work simplifies these challenges and yields accurate numerical solution.The stability and convergence analyses of the methods are examined and proven. To test the developed technique, numerical experiments are carried out and confirmed with theoretical analysis.

Polydopamine (PDA) deposition, obtained from the oxidation of dopamine and other catecholamines is an universal way to coat all known materials with a conformal coating which can subsequently be functionalyzed at will. The structural analogies between polydopamine and eumelanin, the black-brown pigment of the skin, incited to produce stable polydopamine nanoparticles in solution instead of amorphous precipitates obtained from the oxidation of dopamine. Herein, we demonstrate that size controlled and colloidally stable PDA based nanoparticles can be obtained in acidic conditions, where spontaneous auto-oxidation of dopamine is suppressed, using sodium periodate as the oxidant and a protein like alkaline phosphatase as a templating agent. The size of the PDA@Alp nanoparticles depends on the dopamine/enzyme ratio and the obtained particles display the enzymatic activity of alkaline phosphatase with an activity extending up to two weeks after particle synthesis. The PDA@ alkaline phosphatase (Alp) nanoparticles can be engineered in polyelectrolyte multilayered films to potentially design model biosensors.

Curcumin is a promising anti-cancer drug but its applications in cancer therapy are limited due to its poor solubility, short half-life and low bioavailability. In this study, curcumin loaded magnetic alginate / chitosan nanoparticles were fabricated to improve the bioavailability, uptake efficiency and cytotoxicity of curcumin to MDA-MB-231 breast cancer cells. Alginate and chitosan were deposited on Fe3O4 magnetic nanoparticles based on their electrostatic properties. The sizes of the nanoparticles (120-200 nm) were within the optimum range for drug delivery. Sustained curcumin release was obtained use the nanoparticles with the ability to control the curcumin release rate by altering the number of chitosan and alginate layers. Confocal fluorescence microscopy results showed that targeted delivery of curcumin with the aid of magnetic field were achieved. The FACS assay indicated that MDA-MB-231 cells treated with curcumin loaded nanoparticles had a 3-6 folds uptake efficiency to those treated with free curcumin. MTT assay indicated that the curcumin loaded nanoparticles exhibited significantly higher cytotoxicity toward MDA-MB-231 cells than toward HDF cells. The sustained release profiles, enhanced uptake efficiency and cytotoxicity to cancer cells as well as the targeting potential make MACPs a promising candidate for cancer therapy.

In two dimensional disordered lattices, presence of interaction makes particles less localized than the non-interacting ones within the range of disorder strength W ≤ 4 and interaction strength V ≤ 4. If the interaction strength is higher, then particles localize more. Although, a localization-delocalization transition is not found, a transition with changes in the dominant correlations is observed. The nature of correlations between the particles as nearest neighbors become dominant beyond certain disorder strengths.

Most IoT systems meant for implementing mission-critical systems are multi-layered based. The majority of the computing is done in the services and gateway layer. The Gateway layer connects the Internal section of the IoT to the cloud through the Internet. The failure of any node between the services servers and the gateways will isolate the entire network leading to zero tolerance. A networking topology is required to connect the service servers to the gateways, yielding 100% fault tolerance. Empirical formulation of the model chosen to connect the service’s servers to gateways through routers is required to compute the fault tolerance of the network. Rectangular and Interstitial Mesh have been proposed in this paper to connect the service servers to the gateways through the servers that yield 0.999 fault tolerance of the IoT network. An empirical formulation is also presented using which the Fault tolerance of the IoT network can be computed. An enhancement of 11% in the fault tolerance capability of an IoT network has been achieved by implementing Rectangular and Interstitial Mesh in the gateway layer of the network.

The design and engineering of antibacterial materials is key for preventing bacterial adherence and proliferation in biomedical and house-hold instruments. Silver nanoparticles (AgNPs) and chitosan (CHI) are broad-spectrum antibacterial materials with different properties, whose combined application is currently under optimization. This study proposes the formation of antibacterial films with AgNPs embedded in carboxymethylcellulose/chitosan multilayers by the layer-by-layer (LbL) method. The films were deposited onto nanoporous silicon (nPSi), an ideal platform for bioengineering applications, due to its biocompatibility, biodegradability, and bioresorbability. We focus on two alternative multilayer deposition processes: cyclic dip coating (CDC) and cyclic spin coating (CSC). The physicochemical properties of the films were the subject of microscopic, microstructural and surface-interface analyses. The antibacterial activity of each film was investigated against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria strains as model microorganisms. According to the findings, CDC technique produced multilayer films with higher antibacterial activity for both bacteria compared to the CSC method. Bacteria adhesion inhibition was observed from only 3 cycles. The developed AgNPs-multilayer composite film offers advantageous antibacterial properties for biomedical applications.

Cadmium telluride (CdTe), a metallic dichalcogenide material, has been utilized as an absorber layer for thin film-based solar cells with appropriate configurations, and the SCAPS-1D structures program has been used to evaluate the results. In both known and developing thin film photovoltaic systems, a CdS thin film buffer layer has been frequently employed as a traditional n-type heterojunction partner. In this study, numerical simulation was used to find a suitable non-toxic material for the buffer layer instead of CdS, among various types of buffer layers (ZnSe, ZnO, ZnS, and In2S3), and carrier concentrations for the absorber layer (NA) and buffer layer (ND) were varied to determine the optimal simulation parameters. carrier concentrations (NA from 2 x 1012 cm-3 to 2 x 1017 cm-3 and ND from 1 x 1016 cm-3 to 1 x 1022 ??−3) have been differed. The results showed that the CdS as buffer layer based CdTe absorber layer solar cell has the highest efficiency (?%) of 17.43%. Furthermore, high conversion efficiencies of 17.42% and 16.27% have been found for ZnSe and ZnO based buffer layers, respectively. As a result, ZnO and ZnSe are potential candidates for replacing the CdS buffer layer in thin-film solar cells. Here, the absorber (CdTe) and buffer (ZnSe) layers were chosen to improve the efficiency by finding the optimal density of the carrier concentration (acceptor and donor). The simulation findings above provide helpful recommendations for fabricating high-efficiency metal oxide-based solar cells in the lab.

Glucose-sensitive films were prepared by the layer-by-layer (LbL) deposition of poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA+GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA+GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve a more reactive oxygen species (ROS) that was formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the H-PEI/DNA+GOx)5 film was observed when the thin film was immersed in a glucose solution. A (H-PEI/DNA+GOx)5 film exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated decomposition of the film increased with the time. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strength close to physiological conditions, it was possible to slowly decompose the LbL film at a sub-millimolar glucose concentration.

In the paper we present a new test for comparison of the means of multivariate samples with unknown distributions. The test is based on the comparison of the distributions of the distances between the samples’ elements and their means using univariate two-sample Kolmogorov-Smirnov test. The activity of the suggested method is illustrated by numerical analysis of the real-world and simulated data.

The design of multifunctional microcarriers has attracted significant attention because they combine various functions within a single system. In this study, we developed a set of multi-layered hydrogel microcarriers, which were first loaded with chemotherapeutic curcumin (CUR), then using the layer-by-layer (LbL) technique, coated through a polyelectrolyte shell consisting of chitosan (CHIT) or poly(allylamine hydrochloride) (PAH). As an outer layer with antimicrobial function, newly synthesised alkylene quaternary ammonium salt functionalised polyelectrolytes (A-QAS-PEs) were applied. For this purpose, poly(acrylic acid) (PAA) was decorated with dif-ferent hydrophobic side chains (n-hexane and n-dodecane side entities) and different degrees of substitution (m) of quaternary ammonium groups (abbreviated as PAA-C(O)O-(CH2)n-N+(CH3)3(m); n=6,12; m=8-14%). The grafting approach of PAA with the al-kylene quaternary ammonium salt moiety was performed under mild reaction conditions using Steglich esterification followed by quaternisation. The structure of antimicrobial decorated PAA was confirmed by 1H NMR and FTIR, and the mean diameter of all multifunctional microparticles was characterised by SEM. The viscoelastic properties of the functional layers were studied using QCM-D. The release of CUR from the microcarriers was described using a hybrid model, i.e., a combination of first-order kinetics and the Korsmeyer-Peppas model. The antimicrobial activity of functionalised PAA and multilayered CUR-loaded hydrogel microcarriers with quaternary am-monium function was assessed against Staphylococcus aureus and Serratia marcescens by the agar diffusion assay method. Only a limited inhibition zone of PAA was observed, but in the case of both antimicrobial decorated PAA and the corresponding multilayered nanocarriers, the inhibi-tory activity increase was achieved against both strains of bacteria.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

Electrospun nanofiber-supported thin film composite membranes are among the most promising membranes for seawater desalination via forward osmosis. In this study, a high-performance electrospun polyvinylidenefluoride (PVDF) nanofiber-supported TFC membrane was successfully fabricated after molecular layer-by-layer polyelectrolyte deposition. Negatively-charged electrospun polyacrylic acid (PAA) nanofibers were deposited on electrospun PVDF nanofibers to form a support layer consisted of PVDF and PAA nanofibers. This resulted to a more hydrophilic support compared to the plain PVDF nanofiber support. The PVDF-PAA nanofiber support then underwent a layer-by-layer deposition of polyethylenimine (PEI) and PAA to form a polyelectrolyte layer on the nanofiber surface prior to interfacial polymerization, which forms the selective polyamide layer of TFC membranes. The resultant PVDF-LbL TFC membrane exhibited enhanced hydrophilicity and porosity, without sacrificing mechanical strength. As a result, it showed high pure water permeability and low structural parameter values of 4.12 Lm⁻²h⁻¹bar⁻¹ and 221 µm, respectively, significantly better compared to commercial FO membrane. Layer-by-layer deposition of polyelectrolyte is therefore a useful and practical modification method for fabrication of high performance nanofiber-supported TFC membrane.

Two-dimensional (2D) ice I is an atomic-level ice that is composed of two interlocked atom-ic layers saturated with hydrogen bonds. It has recently been experimentally observed but its properties have yet to be clarified. Accordingly, we theoretically studied the hydrophobic properties of 2D ice I. On the contrary, simulation of a hydrogen fluoride molecule on a 2D ice surface manifested that it destroyed the 2d ice structure and connected new hydrogen bonds with water molecules. Investigations of the interfacial effect between 2D and three-dimensional (3D) ice films indicated that the network structure of 2D ice was not de-stroyed by a 3D ice surface, as the former was saturated with hydrogen bonds. However, the surface of 3D ice reorganized to form as many hydrogen bonds as possible. Thus, the 2D ice film was hydrophobic and inhibited the growth of 3D ice. This shows that if 2D ice can be produced on an industrial scale, it could be used as an anti-3D-icing agent under low tem-perature.

Purpose: The accuracy of conventional visual function tests, which emit visible light, decreases in patients with corneal scars, cataracts, and vitreous hemorrhages. In contrast, infrared (IR) light exhibits greater tissue penetrance than visible light and is less susceptible to optical opacities. We therefore compared visual function results obtained using conventional visual function tests and infrared 2-photon microperimetry (2PM-IR) in a subject with a brunescent nuclear sclerotic and posterior subcapsular cataract before and after cataract surgery. Methods: Visual function testing using the cone contrast threshold (CCT) test, conventional microperimetry (cMP), visible light microperimetry from a novel device (2PM-Vis), and 2PM-IR were performed before and after cataract surgery. Results: Cone contrast threshold testing improved for the S-cone, M-cone, and L-cone by 111, 14, and 30. Retinal sensitivity assessed using cMP, 2PM-Vis, and 2PM-IR improved by 18 dB, 17.4 dB, and 3.4 dB, respectively. Conclusions and Importance: 2PM-IR, unlike conventional visual function tests, showed minimal variability in retinal sensitivity before and after surgery. Thus, IR visual stimulation introduces a paradigm shift for measuring visual function in the retina and posterior visual pathways by circumventing optical media opacities.

Yeast two-hybrid approaches, which are based on fusion proteins that must co-localise to the nucleus to reconstitute the transcriptional activity of GAL4 have greatly contributed to understand the nitrogen interaction network of cyanobacteria, whose main hubs are the trimeric PII and the monomeric PipX regulators. The bacterial two-hybrid system, based on the reconstitution in the E. coli cytoplasm of the adenylate cyclase of Bordetella pertussis, should provide a relatively faster and presumably more physiological assay for cyanobacterial proteins than the yeast system. Here we use the bacterial two-hybrid system to gain additional insights into the cyanobacterial PipX interaction network while simultaneously assessing the advantages and limitations of the two most popular two-hybrid systems. Comprehensive mutational analysis of PipX and bacterial two-hybrid assays were performed to compare outcomes between yeast and bacterial systems. We detected interactions previously recorded in the yeast two-hybrid system as negative as well as a “false positive”, the self-interaction of PipX, which is rather an indirect interaction dependent on PII homologs from the E. coli host, a result confirmed by Western analysis with relevant PipX variants. This is, to our knowledge, the first report of the molecular basis of a false positive in the bacterial two-hybrid system.

This article is the third part of a scientific project under the general title "Geometrized vacuum physics based on the Algebra of Signatures". In the first two papers [1,2], the ideal (i.e., non-curved and immobile) local region of vacuum was studied and the foundations of the Algebra of Signatures were laid. This article considers the possibilities of describing the curved and moving state of the same vacuum region on the basis of the mathematical apparatus of the Algebra of Signatures. The reasons for the multilateral consideration of vacuum and twisting of intra-vacuum processes into spiral bundles are disclosed. The 4-tensor is introduced for two-sided and 16-sided consideration of the curvature of the local vacuum region. On the basis of kinematic models, the following assumptions were made: about the inert properties of vacuum layers; about the possibility of displacement of vacuum layers relative to each other at a speed significantly exceeding the speed of light; about the possibility of "rupture" of the local region of vacuum. The proposed kinematic models of the movement of vacuum layers can be a theoretical basis for the development of "zero" (i.e., vacuum) technologies.

Initially introduced almost thirty years ago for the express purpose of providing electronic warfare systems the capabilities to detect, characterize, and identify radar emitters, Specific Emitter Identification (SEI) has recently received a lot of attention within the research community as a physical layer technique for securing Internet of Things (IoT) deployments. This attention is due in large part to SEI’s demonstrated success in passively and uniquely identifying wireless emitters using traditional machine learning and the success of Deep Learning (DL) within the natural language processing and computer vision areas. SEI exploits distinct and unintentional features present within an emitter’s transmitted signals. The existence of these distinctive and unintentional features is attributed to slight manufacturing and assembly variations that exist within and between the components, sub-systems, and systems that comprise an emitter’s Radio Frequency (RF) front end. Although sufficient to facilitate SEI, these features do not hinder normal operations such as detection, channel estimation, timing, and demodulation. However, despite the plethora of SEI publications, it has remained largely a focus of academic endeavors that primarily focus on proof-of-concept demonstration and little to no use in operational networks for various reasons. The focus of this survey is a review of SEI publications from the perspective of its use as a practical, effective, and usable IoT security mechanism, thus we use IoT requirements and constraints (e.g., wireless standard, nature of their deployment) as a lens through which each reviewed paper is analyzed. Previous surveys have not taken such an approach and have only used IoT as motivation, a setting, or a context. In this survey, we consider operating conditions, SEI threats, SEI at scale, publicly available data sets, and SEI considerations that are dictated by the fact that it is to be employed by IoT devices or IoT infrastructure.

Highly-correlated electrons – electrons that engage in strong electron-electron interactions – have been observed in transition metal oxides and quantum dots and can create unusual material behavior that is difficult to model, such as switching between a low resistance metal state and a high resistance Mott insulator state. Tests of devices using a layer-by-layer deposition process for forming multilayer arrays of ferritin (a transition metal (iron) oxide storage protein) have been previously reported that indicate that highly-correlated electron transport is occurring, consistent with models of electron transport in quantum dots. This paper reports the results of the effect of various degrees of structural homogeneity on the electrical characteristics of these ferritin arrays, as well as demonstrating that these structures can provide a switching function associated with the circuit that they are contained within, consistent with the observed behavior of highly-correlated electrons.

Liquid crystal elastomers (LCEs) are shape morphing materials whose large and reversible shape transformation results from the coupling between the mobile anisotropic properties of liquid crystal (LC) units and the rubber elastic of polymer networks. Their shape changing behaviors under the stimuli are largely directed by LC orientations, and therefore various strategies have been developed to spatially modulate the LC alignments. But most of the methods suffer from complex fabrication technologies or intrinsic limitations in applicability. To address this issue, programmable complex shape changes in some types of LCEs, such as polysiloxane side-chain LCEs or thiol-acrylate main-chain LCEs, etc, have been achieved by using a mechanical alignment programming process coupled with two-step crosslinking. Here, we report a polysiloxane main-chain LCE with programmable 2D and 3D shape changing performances achieved by mechanically programming the polydomain LCE between the two crosslinking steps. The resulting LCEs exhibited reversible thermal induced shape transformation between the initial and programmed shapes due to the two-way memory between the first network structure and the second network structure. Our work would be potential for expanding the applications of LCE materials in actuators, soft robotics and smart structures where arbitrary and easily programmed shape morphings are needed.

The details of ac-conductivity measurements in a colloidal electrolyte cell with flat control gate electrodes are discussed. The use of impedance diagnostics in studies of transport phenomena in such systems requires caution in the definition of the thickness of the screening accumulation layers that appear along the metal-electrolyte interfaces. The value of this characteristic length λ0 critically depends on the volume fraction ϕ⊙ of colloidal particles in the bulk of electrolyte. Accounting for the dependence λ0(ϕ⊙) makes it possible to consistently explain the large discrepancy in the available experimental data regarding the influence of colloidal fraction on the effective conductivity of the colloidal suspension.

This brief review introduces some general properties of lower atmospheric motions that may be exploited by birds, linking historical findings and current knowledge from both observational and modeling perspectives. The relative importance of turbulent mixing resulting from wind shear and that from buoyant thermals is emphasized as well as the determinants of the geometry of the resulting vertical motions.

Copper indium gallium selenide (CIGS) is an inexpensive material that has the potential to dominate the next-generation photovoltaic (PV) industry. Here we detail computational investigation of CIGS solar cell with encouragement of adopting cuprous dioxide (Cu₂O) as a Hole Transport Layer (HTL) for efficient fabricated CIGS solar cells. Although Cu₂O as a HTL has been studied earlier for perovskite and other organic/inorganic solar cell yet no study has been detailed on potential application of Cu₂O for CIGS solar cells. With the proposed architecture, recombination losses are fairly reduced at the back contact and contribute to enhanced photo-current generation. With the introduction of Cu₂O, the overall cell efficiency is increased to 26.63%. The wide-band of Cu₂O pulls holes from the CIGS absorber which allows smoother extraction of holes with experiencing lesser resistance. Further, it was also inferred that, HTL also improves the quantum efficiency (QE) for photons with large wavelengths thus increases the cell operating spectrum.

This article is devoted to the issues of thermal softening of materials in the surface layer of forging tools. The research covers numerical modeling of the forging process, laboratory tests of tempering of nitrided layers and the analysis of tempering of the surface layer of tools in the actual forging process. Numerical modeling was supported by measuring the temperature inside the tools with a thermocouple inserted into the tool to measure the temperature as close to the surface as possible. The modeling results confirmed the possibility of tempering the die material. The results of laboratory tests made it possible to determine the influence of temperature on tempering at different surface layer depths. Numerical analysis and measurement of surface layer microhardness of tools revealed the destructive effect of temperature during forging on the tempering of the nitrided layer and on the material layers located deeper below the nitrided layer.

Electrochemical energy conversion and storage is key for the use of regenerative energies at large scale. A thorough understanding of the individual components, such as the ion conducting membrane and the electrode layers, can be obtained with scattering techniques on atomit to molecular length scales. The largely heterogeneous electrode layers of High-Temperature Polymer Electrolyte Fuel Cells are studied in this work with small- and wide-angle neutron scattering at the same time with the iMATERIA diffractometer at the spallation neutron source at J-PARC, opening a view on structural properties on atomic to mesoscopic length scales.

Mixing layer height (MLH) is a crucial parameter for air quality modelling that is still not routinely measured. Common methods for MLH determination use atmospheric profiles recorded by radiosonde but they suffer from course temporal resolution since balloon launching is only twice a day. Recently cheap ceilometers are gaining popularity in the retrieval of MLH diurnal evolution based on aerosol profiles. This study presents a comparison of a proprietary (Jenoptik) and a free available (STRAT) algorithms to retrieve MLH diurnal cycle. The comparison is accomplished in summer season over urban area and radiosonde data is used to estimate MLHs according to parcel, lapse rate, and Richardson methods (the last algorithm is used as a reference in the study) in addition. It was found that STRAT and Jenoptik give lower MLH than radiosonde with an underestimation of about 150m and 650m respectively. Additionally, STRAT showed reasonable performance in tracking of MLH diurnal evolution. Daily MLH maximum of about 2000m was found in the late afternoon (18-19 LT). In contrast, Jenoptik algorithm showed more weaknesses, mainly attributed to its real-time operation and independent processing of a single profile. At night and during morning transition period, both lidar-based methods showed difficulties as MLH was often in the ceilometer’s incomplete overlapping zone so residual or advected aerosol layers aloft were misleadingly reported as mixing layer (ML).

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Bioactive surface coatings have retained the attention of researchers and physicians due to their versatility and range of applications in orthopedics, particularly in infection prevention. Antibacterial metal nanoparticles (mNPs) are a promising therapeutic, with vast application opportunities on orthopedic implants. The current research aimed to construct a polyelectrolyte multilayer on a highly porous titanium implant using alternating thin film coatings of chitosan and alginate via the layer-by-layer (LbL) self-assembly technique, along with the incorporation of silver nanoparticles (AgNPs) or titanium dioxide nanoparticles (TiO2NPs), for antibacterial and osteoconductive activity. These mNPs were characterized for their physicochemical properties using quartz crystal microgravimetry with dissipation system, nanoparticle tracking analysis, scanning electron microscopy, and atomic force microscopy. Their cytotoxicity and osteogenic differentiation capabilities were assessed by AlamarBlue and alkaline phosphatase (ALP) activity assays, respectively. The antibiofilm efficacy of the mNPs tested against Staphylococcus aureus. The LbL polyelectrolyte coating was successfully applied to the porous titanium substrate. A dose-dependent relationship between nanoparticle concentration and ALP as well as antibacterial effects was observed. TiO2NP samples were also less cytotoxic than AgNP counterparts, although similarly antimicrobial. Together, these data serve as a proof-of-concept for a novel coating approach for orthopedic implants with antimicrobial and osteoconductive properties.

Membrane-based beverage dealcoholization is a successful process for producing low- and non-alcoholic beer and represents a fast-growing industry. Polyamide NF and RO membranes are commonly applied for this process. Polyelectrolyte multilayer (PEM) NF membranes are emerging as industrially relevant species and their unique properties (usually hollow fiber geometry, high and tunable selectivity, low fouling) underlines the importance of testing them in the food industry as well. To test PEM NF membranes for beer dealcoholization, at small pilot scale we dealcoholized filtered and unfiltered lager beer with the tightest available commercial polyelectrolyte multilayer NF membrane (NX Filtration dNF40), which has a MWCO=400Da which is quite high for these purposes. Dealcoholization is possible with a reasonable flux (10 LMH) at low pressures (5-8.6 bar) with a real extract loss of 16-18% and an alcohol passage of ~100%. Inorganic salt passage is high (which is typical for PEM NF membranes), which greatly affected beer flavor. During the dealcoholization process, the membrane underwent changes which substantially increased its salt rejection values (MgSO4 passage decreased 4-fold) while permeance loss was minimal (less than 10%). According to our sensory examination, the process yielded an acceptable flavored beer which could be greatly enhanced by the addition of the lost salts and glycerol.

This article describes in detail the numerical modeling of a CZTS (copper zinc tin sulfide) based kesterite solar cell. The Solar Cell Capacitance Simulator -one-dimension (SCAPS-1D) software was used to simulate MO/CZTS/CdS/ZnO/FTO structured solar cells. The parameters of different photovoltaic thin-film solar cells are estimated and analyzed using numerical modeling. The effects of various parameters on the performance of the photovoltaic cell and the conversion efficiency are discussed. Since the response of the solar cell is also contingent on its internal physical mechanism, J-V characteristic measures are insufficient to characterize the behavior of a device. Different features, as well as different potential conditions, must be considered for simulation, disregarding the belief in the modeling of a solar cell. With a conversion efficiency of 25.72%, a fill factor of 83.75%, a short-circuit current of 32.96436 mA/cm2 and an open-circuit voltage of 0.64V, promising optimized results have been achieved. The findings will be useful in determining the feasibility of fabricating high-efficiency CZTS-based photovoltaic cells. The efficiency of a CZTS-based experimental solar cell is also discussed. First, the effects of experimentally developed CZTS solar cells are simulated in the SCAPS-1D environment. The experimental results are then compared to the SCAPS-1D simulated results. The conversion efficiency of an optimized system increases after cell parameters are optimized. Using one-dimensional SCAPS-1D software, the effect of system parameters such as the thickness, acceptor and donor carrier concentration densities of absorber and electron transport layers, and the effect of temperature on the efficiency of CZTS-based photovoltaic cells is investigated. The proposed results will greatly assist engineers and researchers in determining the best method for optimizing solar cell efficiency, as well as in the development of efficient CZTS-based solar cells.

Background: Central serous chorioretinopathy (CSC) is a common macular condition characterized by detachment of the neuroretina and is a frequent cause of central vision loss in adults. Among the various therapeutic strategies, subthreshold microsecond pulsed laser (SML) treatment has become a useful option. Despite the suggested involvement of choroidal circulatory disturbances in CSC, effects of this treatment on macular microperfusion have not been fully evaluated yet. Herein, we report the impact of SML on retinal and choroidal microvascular flow using non-invasive optical coherence tomography (OCT) angiography (OCTA). Methods: In this study, CSC patients with persistent subretinal fluid (SRF) with or without secondary choroidal neovascularization (CNV) were included (referred to as pachychoroid neovasculopathy (PNV) group and CSC group, respectively). SML was conducted using a yellow (577 nm) laser with duty cycle of 10%, spot size of 200 µm and duration of 200 ms. Best corrected visual acuity (BCVA) as well as OCT and OCTA images were evaluated at baseline and 4 weeks after SML. OCTA parameters of interest included full retinal perfusion (FRP), choriocapillaris perfusion (CCP), Sattler’s layer perfusion (SLP), and Haller’s layer perfusion (HLP), which were evaluated longitudinally and compared to unaffected fellow eyes. Results: 27 affected eyes and 17 fellow eyes from 27 patients were included. Before treatment, central retinal thickness (CRT) and subfoveal choroidal thickness (SFCT) of affected eyes were significantly larger than in fellow eyes. Four weeks after SML, CRT decreased significantly, whereas perfusion parameters did not change. In subgroup analyses, the CSC group showed a significant decrease of SFCT, whereas the PNV group did not despite the decrease of CRT. Conclusion: Our results suggest that the SML may SFCT of CSC, but not of PNV patients at least within four weeks following treatment. This effect seems to be independent of the change in choroidal perfusion measured with OCTA.

Modifiable THz spectral shapes are important tools that facilitate the comprehensive study of phonon dynamics in condensed matter systems. The generation of narrow bandwidth THz spectra with tunable center frequency which are suitable THz forms needed to achieve such objectives are currently less studied from the table top laser-induced plasma emitters’ perspective. This experimental research is aimed at developing a robust two-color laser induced plasma set-up comprising of a temporal pulse stretcher and an Optical Parametric Amplifier that generates chirped and wavelength tunable pulses respectively. By focusing and independently controlling the ω and 2ω arms of the chirped pulses resulting after the interaction with a β-BBO crystal, I aim to generate narrow bandwidth THz signal (from plasma) scalable at MV/cm intensity and tunable in a wide THz spectral range, in addition to varying the frequency ratio mix.

In this short communication, we conducted first-principles calculations to explore the stability of boron monochalcogenides (BX, X=S, Se or Te), as a new class of two-dimensional (2D) materials. We predicted BX monolayers with two different atomic stacking sequences of ABBA and ABBC, referred in this work to 2H and 1T, respectively. Analysis of phonon dispersions confirm the dynamical stability of BX nanosheets with the both 2H and 1T atomic lattices. Ab-initio molecular dynamics simulations reveal the outstanding thermal stability of all predicted monolayers at high temperatures over 1500 K. BX structures were found to exhibit high elastic modulus and tensile strengths. It was found that BS and BTe nanosheets can show high stretchability, comparable to that of the graphene. It was found that all predicted monolayers exhibit semiconducting electronic character, in which 2H structures present lower band-gaps as compared with 1T lattices. The band-gap values were found to decrease from BS to BTe. According to the HSE06 results, 1T-BS and 2H-BTe show respectively, the maximum (4.0 eV) and minimum (2.06 eV) electronic band-gaps. This investigation introduces boron monochalcogenides as a novel class of 2D semiconductors with remarkable thermal, dynamical and mechanical stability.

We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

The optimized design of catalyst layer (CL) plays a vital role to improve the performance of polymer electrolyte membrane fuel cells (PEMFCs). The need to improve transport and catalyst activity is especially important at low Pt loading, where local oxygen and ionic transport resistances decrease the performance due to an inevitable reduction of active catalyst sites. In this work, local oxygen and ionic transport are analyzed using direct numerical simulation on virtually reconstructed microstructures. Four morphologies are examined: (i) heterogeneous, (ii) uniform, (iii) uniform vertically-aligned, and (iv) meso-porous ionomer distributions. The results show that the local oxygen transport resistance can be significantly reduced, while maintaining good ionic conductivity, through the design of high porosity CLs (ε≃0.6−0.7) with low agglomerated ionomer morphologies. Ionomer coalescence into thick films can be effectively mitigated by increasing the uniformity of thin films and reducing the tortuosity of ionomer distribution (e.g., good ionomer interconnection in supports with a vertical arrangement). The local oxygen resistance can be further decreased by the use of blended ionomers with enhanced oxygen permeability and meso-porous ionomers with oxygen transport routes in both water and ionomer. In summary, achieving high performance at low Pt loading in next-generation CLs must be accomplished through a combination of high porosity, uniform and low tortuosity ionomer distribution, and oxygen transport through activated water.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

This work focused on the evaluation of some machine learning (ML) models and their application in e-health, using intermediate nodes within an Internet of Things (IoT) platform used for heartbeat anomaly detection. For the evaluation of ML models, a set of statistical validation metrics was selected. These metrics were applied in the training, testing and validation phases of the models. The results obtained can determine relevant factors for the selection of ML models, either based on the statistical and intrinsic efficiency of the ML models, or on their suitability to be implemented in intermediate nodes within an IoT platform. the more Lightweight models such as Simple Linear Regression, Logistic Regression, and K Nearest Neighbors, could easily operate in intermediate nodes, and they are models that require low processing and storage to work. In conclusion, the approach for intermediate nodes of Internet of Things platforms using cognitive networks decreases the processing cost in cloud computing and transfers it to the fog layer.

A better study of the postnatal retinal development is not only essential for the in-depth understanding of the nature of the vision system but also may provide insights for treatment developments of eye conditions, such as retinopathy of premature (ROP). To date, quantitative analysis of postnatal retinal development is primarily limited to endpoint histological examination. This study is to validate in vivo optical coherence tomography (OCT) for longitudinal monitoring of postnatal retinal development in developing mouse eyes. Three-dimensional (3D) frame registration and super averaging were adopted to investigate the fine structure of the retina. Interestingly, a hyporeflective layer (HRL) between the nerve fiber layer (NFL) and inner plexiform layer (IPL) was observed in developing eyes and gradually disappeared with aging. To interpret the observed retinal layer kinetics, a model based on eyeball expansion, cell apoptosis, and retinal structural modification was proposed.

In this paper, a further mathematical analysis of some previous results of the author’s ongoing investigation regarding Prandtl’s equations is accomplished. In particular, the objective of the present work is the performance of an approximate explicit solution to Prandtl’s system of equations for a laminar, isothermal, incompressible and steady boundary layer flow of a Newtonian fluid, over an infinite horizontal flat plate.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

Suppressing the charge recombination at the interface of photoanode/electrolyte is the crucial way to enhance the photovoltaic performance of quantum dot sensitized solar cells (QDSSCs). In this scenario, ZnS/SiO2 blocking layer was deposited on TiO2/CuInS2 QDs to inhibit the charge recombination at photoanode/electrolyte interface. As a result, the TiO2/CuInS2/ZnS/SiO2 based QDSSCs delivers a power conversion efficiency (η) value of 4.63%, which is significantly higher than the 2.15% and 3.23% observed for QDSSCs with a TiO2/CuInS2 device and TiO2/CuInS2/ZnS, respectively. Electrochemical impedance spectroscopy and open circuit voltage decay analyses indicate that ZnS/SiO2 passivation layer on TiO2/CuInS2 suppress the charge recombination at the photoanode/electrolyte interface and prolongs the electron lifetime.

Ventilation in cities is crucial for the well being of their inhabitants. Therefore, local governments require air ventilation assessments (AVAs) prior to the construction of new buildings. In a standard AVA, however, only neutral stratification is considered, although diabatic and particularly unstable conditions may be observed more frequently in nature. The results presented here indicate significant changes in ventilation within most of the area of Kowloon City, Hong Kong, included in the study. A new definition for calculating ventilation was introduced, and used to compare the influence of buildings on ventilation under conditions of neutral and unstable stratification. The overall ventilation increased due to enhanced vertical mixing. In the vicinity of exposed buildings, however, ventilation was weaker for unstable stratification than for neutral stratification. The influence on ventilation by building parameters, such as the plan area index, was altered when unstable stratification was considered. Consequently, differences in stratification were shown to have marked effects on ventilation estimates, which should be taken into consideration in future AVAs.

Motivated by the increasing need of optimised micro-devices for droplets production in medical and biological applications, this paper introduces an integrated approach for the study of the liquid-liquid droplet creation in flow-focusing micro cross-junctions. The micro-junction considered is characterised by a restriction of the channels cross-sections in the junction, which has the function of focusing the flow in the region of the droplet formation. The problem is studied numerically in OpenFOAM environment and validated by the comparison with experimental results obtained by high-speed camera images and micro-PIV measurements. The analysis of the forces acting on the dispersed phase during the droplet formation and the diameter of the droplets obtained numerically are considered for the development of a model of the droplet breakup under the squeezing regime. On the basis of energy balancing during the breakup, a relation between interfacial tension, the size of the cross-sections in the junction, and the time interval needed for droplet creation is obtained, which yields a novel correlation between the dimensionless length of the droplet and the dimensionless flow rate. This correlation is general and can be used to predict the droplet diameters produced by similar micro-junctions with different aspect ratios and extended to different geometries of flow-focusing micro-junctions.

This study explores how the properties of heater materials impact nucleate pool boiling using a comprehensive simulation model. The model integrates well-known heat transfer mechanisms, allowing us to assess the effects of two distinct heater materials. Findings indicate that materials with higher thermal conductivity, such as copper, notably improve refrigeration efficiency in nucle- ate boiling. The study provides insights into the relationship between bubble growth, microlayer recovery beneath a bubble, temperature fluctuations, and heater properties. Comparisons between copper and silicon oxide underscore variations in bubble frequency, attributed to differences in bubble growth time, microlayer recovery time, and material-dependent behavior. The influence of neighboring bubbling sites, especially pronounced in silicon oxide due to its low thermal conductivity and diffusivity, was observed. Temperature variations in such materials became highly visible due to their significant inertia in recovery. Simulation results align well with empirical correlations, confirming the model’s versatility in capturing the intricate phenomena of nucleate pool boiling.

We carry out in a thin heterogeneous porous layer, the multiscale analysis of Smoluchowski's discrete diffusion-coagulation equations describing the evolution density of diffusing particles that are subject to coagulate in pairs. Assuming that the thin heterogeneous layer is made of microstructures that are uniformly distributed inside, we obtain in the limit an upscaled model in lower space dimension. We also prove a corrector-type result very useful in numerical computations. In view of the thin structure of the domain, we appeal to a concept of two-scale convergence adapted to thin heterogeneous media to achieve our goal.

Classical numerical methods for solving ordinary differential equations often produce less accurate results when applied to problems with oscillatory or periodic behaviour. To adapt them for such problems, they are usually modified using the exponential fitting technique. This adaptation allows for the construction of new methods from their classical counterparts. The new methods are usually more accurate, efficient and suitable for handling the oscillatory or periodic behaviour of the problem. In this work, we construct a two-parameter exponentially-fitted Taylor method suitable for solving oscillatory or periodic problems that possess two frequencies. The construction algorithm is based on a proposed six-step flowchart discussed by authors in related literature. Two standard test problems were used to illustrate the accuracy and performance of the proposed method.

The generalized dual-kinetic-balance approach for axially symmetric systems is employed to solve the two-center Dirac problem. The spectra of one-electron homonuclear quasimolecules are calculated and compared with the previous calculations. The analysis of the monopole approximation with two different choices of the origin is performed. Special attention is paid to the lead and xenon dimers, Pb82+–Pb82+–e− and Xe54+–Xe54+–e−, where the energies of the ground and several excited σ-states are presented in the wide range of internuclear distances. The developed method provides the quasicomplete finite basis set and allows for construction of the perturbation theory, including within the bound-state QED.

Light-gated ion channel and ion pump rhodopsins are widely used as optogenetic tools and these can control the electrically excitable cells as: (1) they are a single-component system i.e., their sensor and effector functions are encoded by the 7-transmembrane domains and (2) they show fast kinetics with small dark-thermal recovery time. In cellular signaling, a signal receptor, modulator and effector components are involved for attaining synchronous multicomponent regulation. Optical modulation of this network requires either receptor to effector encoded in a single ORF or direct modulation of the effector domain through bypassing all upstream players. Recently discovered modular rhodopsins like rhodopsin guanine cyclase (RhoGC) and rhodopsin phosphodiesterase (RhoPDE) paves the way to establish proof of concept. Light sensor coupled modular system could be expressed in a precise cell type and which holds great potential in the advancement of optogenetics 2.0. It would enable manipulating entire relevant cell signaling system. Here, we had identified 50 novels modular rhodopsins with variant rhodopsins domain and its diverse cognate signaling cascades encoded in a single ORF, which are associated with specialized functions in the cells. These novel modular algal rhodopsins have been characterized functionality based on their sequence and structural homology with previously characterized rhodopsins. Presented novel modular rhodopsins with various effector domains hold potential to expand optogenetics tool kit to regulate various cellular signaling pathways across the diverse biological model systems.

Conventional method for monitoring the IgG levels suffered from some apparent problems such as long assay time, multistep processing, and high overall cost. An effective and suitable optical platform for label-free biosensing has been investigated by the implementation of antibody/antigen immunoassays. Thus, the ultrasensitive detection of IgG levels can be achieved by exploiting the dispersion turning point (DTP) existed in the tapered two-mode fibers (TTMFs) due to the sensitivity will reach ±∞ on either side of the DTP. Tracking the resonant wavelength shift it was found that the fabricated TTMF device exhibited limits of detection (LOD) down up to concentrations of 10 fg/mL of IgG in PBS solution. Such immunosensors based on the DTP have great significance on trace detection of IgG due to simple detection scheme, quick response time, and miniaturation.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

New TLC-densitometric method have been developed for the identification and quantification of paracetamol (PA), propyphenazone (PP) and caffeine (C) of Saridon tablets using the NP-TLC technique combined with densitometry. This method allows for the simultaneous determination of PA, PP, and C in the same sample. Among all tested chromatographic conditions, the mixture consisting of chloroform + toluene + ethyl acetate + ethanol + acetic acid (18:18:7.5:5.0:0.3, v/v) and silica gel 60F254 plate proved to be the most effective for the separation of three tested active pharmaceutical ingredients (APIs) and substances related to paracetamol. The fully validation of the proposed NP-TLC method proves that it is specific, precise, accurate, robust and sensitive. The percentage content in relation to the content declared by the manufacturer is for propyphenazone 99.8%, paracetamol 101.6% and caffeine 100.8%, which are in accordance with pharmacopoeial requirements. The results presented indicate the possibility of using the developed method in the routine control of pharmaceutical preparations containing these APIs. The proposed method is economical and more sensitive compared to the previously proposed planar methods for the simultaneously determination of PA, PP and CAPIs. Will be an What is more, the presented method may be anaxcellent excellent economical alternative when HPLC method is unavailable for such determination.

With increasing demand from unmanned driving and robotics, more attention has been paid to point cloud-based 3D object accurate detection technology. However, due to the sparseness and irregularity of the point cloud, the most critical problem is how to utilize the relevant features more efficiently. In this paper, we proposed a point-based object detection enhancement network to improve the detection accuracy in the 3D scenes understanding based on the distance features. Firstly, the distance features are extracted from the raw point sets and fused with the raw features about reflectivity of the point cloud to maximizing the use of information in point cloud. Secondly, we enhanced the distance features and raw features that we collectively refer to them as self-features of the key points in Set Abstraction (SA) layers with the self-attention mechanism, so that the foreground points can be better distinguished from the background points. Finally, we revised the group aggregation module in SA layers to enhance the feature aggregation effect of key points. We conducted experiments on the KITTI dataset and nuScenes dataset and the results show the enhancement method proposed in this paper has excellent performance.

Several chemistry-climate models (CCM) underestimate the total column ozone (TCO) over the polar region in the Southern Hemisphere during wintertime. To evaluate potential causes of the problem, we exploit CCM SOCOLv3 to study the TCO over Antarctica sensitivity to the: (1) photo-dissociation rates of ozone for large solar zenith angles; (2) rates of the stratospheric heterogeneous reactions, and (3) intensity of the meridional flux into the polar regions due to sub-grid scale mixing processes in the model. Comparisons of the model results with the satellite-based IASI (Infrared Atmospheric Sounder Interferometer) sensor measurements showed that the most important processes for the improvement of the polar ozone simulation results are photolysis and horizontal mixing. The reasonable tuning of these factors has allowed us to improve the model representation of the ozone annual cycle over the southern polar region. The proposed increase of the horizontal mixing can be recommended for the CCMs with relatively low horizontal resolution.

In permafrost regions, ground surface deformations induced by freezing and thawing threaten the integrity of the built environment. Mapping the frost susceptibility of the ground at a high spatial resolution is of practical importance for the construction and planning sectors. We processed Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) data from thawing seasons 2015 to 2019, acquired over the area of Ilulissat, West Greenland. We used a least-squares inversion scheme to retrieve the average seasonal displacement (S) and long-term deformation rate (R). We secondly investigated two different methods to extrapolate active layer thickness (ALT) measurements, based on their statistical relationship with remotely-sensed surface characteristics. A Generalized Linear Model (GLM) was first implemented, but the model was not able to fit the data and represent the ALT spatial variability over the entire study domain. ALT were alternatively averaged per vegetation class, using a land cover map derived by supervised classification of Sentinel-2 images. We finally estimated the active layer ice content and used it as a proxy to map the frost susceptibility of the ground at the community scale. Fine-grained sedimentary basins in Ilulissat were typically frost susceptible and subject to average seasonal downward displacements of 3 to 8 cm. Areas following a subsiding trend of up to 2.6 cm/yr were likely affected by permafrost degradation and melting of ground ice below the permafrost table. Our approach enabled us to identify frost-susceptible areas subject to severe seasonal deformations, and/or long-term subsidence induced by degrading permafrost. Used in combination with traditional site investigations, InSAR maps provide valuable information for risk management and community planning in the Arctic.

Herein we foremost detailed the numerical modeling of the double absorber layer- methyl ammonium lead iodide– carbon nitride layer solar cell and subsequently provided in-depth insight on the active layer associated with dominant radiative and non-radiative recombination losses limiting the efficiency ( ) of the solar cell. Under recombination kinetics phenomena, we explored the influence of Radiative recombination, Auger recombination, Shockley Read Hall recombination, the energy distribution of defects; Band Tail recombination (Hoping Model), Gaussian distribution, metastable defect states including single donor (0/+), single acceptor (-/0), Double Donor (0/+/2+), double acceptor (2/-/0-), and the interface layer defects on the output characteristics of the solar cell. Setting defect (or trap) density to with uniform energy distribution of defects for all the layers, we achieved the of 24. 16 %. A considerable enhancement in power conversion efficiency was perceived as we reduced the trap density to for the absorber layers. Further, it was observed that for the absorber layer with double donor defect states, the active layer should be carefully synthesized to reduce crystal order defects to keep the total defect density as low as to achieve efficient device characteristics

An explanation of aerodynamic lift still is under controversial discussion as can be seen, for example, in a recent published article in Scientific American [1]. In contrast to an approach via integral conservation laws we here review an approach via the classical Kutta-Condition and its relation to boundary layer theory. Thereby we summarize known results for viscous correction to the lift coefficient for thin aerodynamic profiles and try to remember the work on triple-deck or higher order Boundary Layer theory, its connection to interactive boundary layer theory, viscous/inviscid coupling as implemented to well-known engineering code Xfoil. Finally we compare its findings to simple 2D numerical solution of full Navier Stokes equations (CFD)models. As a conclusion, a clearer definition of terms like understanding and explanation applied to the phenomenon of aerodynamic lift will be given.

During the long-term operation of the plasma reactor, decreases in the plasma concentration were noticed despite the constant maintenance of all parameters. One of the factors is the decrease of the nitrogen content on the surface of the electrode, in order to eliminate it, the supply voltage has been increased to 11 kV. The next decisive factor in the decrease of plasma concentration is the oxidation of the electrode surface, therefore two electrodes were used: first one with solid gold and the other one copper covered with galvanized gold with a thickness of 10 μm. During the experiment, a large decrease in plasma concentration was observed when the electrode coated by gold was used. High-energy electrons have knocked out the gold atoms from the electrode, as a result of which the gold evaporated and the raids layers formed. After a month of working of the electrodes, metallographic researches were carried out, the results of which are described in this publication.

Knowledge about laminar-turbulent transition on operating multi-megawatt wind turbine blades needs sophisticated equipment like hot-films or microphone arrays. Contrarily thermographic pictures can easily be taken from the ground and temperature differences indicate different states of the boundary layer. The accuracy however, still is an open question, so that an aerodynamic glove known from experimental research on aero-planes was used to classify the boundary-layer state of a 2 megawatt wind turbine blade operating in the orthern part of Schleswig-Holstein, Germany. State-of-the-art equipment for measurering static surface pressure was used for monitoring the lift distribution. To distinguish laminar and turbulent parts of the boundary layer (suction side only) 48 microphones were applied together with ground-based thermographic cameras from two teams. Additionally, an optical camera mounted on the hub was used to survey vibrations. During start-up (from 0 to 9 rpm) extended, but irregularly shaped regions of a laminar boundary layer were observed which had the same extension measured both with microphones and Thermography. When an approximately constant rotor rotation (9 rpm corresponding to approximately 6 m/s wind-speed) was achieved, a flow transition was visible at the expected position of 40 % chord length on the rotor blade, which was fouled with dense turbulent wedges and an almost complete turbulent state on the glove was detected. In all observations, quantitative determination of the flow transition positions from thermography and microphones agree well within their accuracy.

Carburizing of stainless steels at low temperatures (below 500°C) develops a high content carbon layer, known for its high hardness. X-ray Diffraction investigation indicates that carburization treatment does not impact the structure of substrate; however, introduced carbon causes expansion in the carburized layer through the increase in d-spacing. Characterization of carbon concentration and hardness profiles indicate that carbon content gradually decreases while moving further into the substrate; and the origin of the increased hardness of the expanded layer arises from the super-saturated carbon content, following the solid solution strengthening theory. An area that is not well understood is in regard to the carburized layer’s relation to the substrate and the significance in their differences. Using two grades of stainless steel, AISI 316L and PH 17-4, it was observed that the carburized layer is not a separate layer, but a higher carbon content version of the substrate,

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

This paper presents a new algorithm for semi-supervised action recognition using adaptive feature analysis. We model the samples of the same action as the same manifold and those of different actions as different manifolds, and integrate feature correlation mining and visual similarity mining into a joint framework. By maximizing the separability between different classes based on the labeled data, the proposed algorithm learns multiple features from labeled data and utilizes the intrinsic geometric structure of the data distribution between labeled and unlabeled data to boost the recognition. We introduce Projected Barzilai-Borwein (PBB) to train a subspace projection matrix as classifier. Extensive experiments on three benchmark datasets demonstrate that our algorithm outperforms the existing semi-supervised action recognition algorithms when there are a few labeled training samples.

When there is uncertainty in the value of parameters of the input random components of a stochastic simulation model, two-level nested simulation algorithms are used to estimate the expectation of performance variables of interest. In the outer level of the algorithm (n) observations are generated for the parameters, and in the inner level (m) observations of the simulation model are generated with the value of parameters fixed at the value generated in the outer level. In this article, we consider the case in which the observations at both levels of the algorithm are independent, showing how the variance of the observations can be decomposed into the sum of a parametric variance and a stochastic variance. Next, we derive central limit theorems that allow us to compute asymptotic confidence intervals to assess the accuracy of the simulation-based estimators for the point forecast and the variance components. Under this framework, we derive analytical expressions for the point forecast and the variance components of a Bayesian model to forecast sporadic demand; and we use these expressions to illustrate the validity of our theoretical results by performing simulation experiments using this forecast model.

Melanoma is a type of highly malignant and metastatic skin cancer. In situ molecular imaging of endogenous levels of the melanoma biomarker tyrosinase (TYR) may decrease the likelihood of mortality. In this study we proposed the weakly fluorescent probe 1-(4-(2-(4-(dicyanomethylene)-4H-chromen-2-yl)vinyl)phenyl)-3-(4-hydroxybenzyl)urea (DCM-HBU), which releases a strong red-shifted fluorescent signal after a TYR-mediated oxidation followed by hydrolysis of the urea linkage. The large Stokes shift of the dye is owed to the recovery of the intramolecular charge transfer (ICT) effect. The resulting probe derivate shows a highly ratiometric fluorescence output. Furthermore, the simultaneous excitation by two near-infrared (NIR) photons of the released DCM-NH2 fluorophore could avoid the usual drawbacks, such as cellular absorption, autofluorescence and light scattering, due to an usually short wavelength of the excitation light on biological systems, resulting in images with deeper tissue penetration. In addition, the probe is useful for the quantitative sensing of TYR activity in vivo, as demonstrated in zebrafish larvae. This new ratiometric two photon NIR fluorescent probe is expected to be useful for the accurate detection of TYR in complex biosystems at greater depths than other one-photon excited fluorescent probes.

We define degree of dependence of two events A and B in a probability space by using Boltzmann-Shannon entropy function of an appropriate probability distribution produced by these events and depending on one parameter (the probability of intersection of A and B) varying within a closed interval I. The entropy function attains its global maximum when the events A and B are independent. The important particular case of discrete uniform probability space motivates this definition in the following way. The entropy function has a minimum at the left endpoint of I exactly when one of the events and the complement of the other are connected with the relation of inclusion (maximal negative dependence). It has a minimum at the right endpoint of I exactly when one of these events is included in the other (maximal positive dependence). Moreover, the deviation of the entropy from its maximum is equal to average information that carries one of the binary trials defined by A and B with respect to the other. As a consequence, the degree of dependence of A and B can be expressed in terms of information theory and is invariant with respect to the choice of unit of information. Using this formalism, we describe completely the screening tests and their reliability, measure efficacy of a vaccination, the impact of some events from the financial markets to other events, etc.

Increasing market participation among smallholder farmers have a big potential to uplift living standards of poor through increasing production and consumption pattern. Although, smallholder farming made 95% of total crop production in Ethiopia, they are exposed to a marketing bottleneck that hinders benefits from their produce. The objective of this study was analyzing factors determining smallholder Teff farmer decision to participate in output market and level of marketed output.The study used data from 190 respondents from four selected Teff dominant kebeles of Gena-Bossa districts in Dawro Zone, through structured questioner. This investigation was imperative because no adequate research has been done in study area in examining the hindering factors of farmers’ market participation. Moreover, in the prior study, different authors come up with varied outcomes in diverse country and geographic location concerning poor farmers’ market participation decision. The descriptive statistics and Heckman two stage econometric methods were employed to analyze data collected from sampled household. The significance of coefficient of inverse Mill’s ratio ( ) indicates the presence of self-selection bias and the effectiveness of applying Heckman two stage model. The results of study show that the smallholder decision to participate in output market were positively influenced by size of land holding, availability of family labor force, education status of household head, accessibility of credit service and access to market price information. On the other hand, size of family member, sex of house hold head being female and distance to market place discourage probability of Teff farmer market participation decision. Moreover, the second stage estimation reveals that, the education status of house hold head, size of farm land, amount of Teff crop produced, accessibility of market information, the size of family labor force and being member to farm cooperative increase the quantity of marketable output, whereas, large number of family size decline the level of Teff crops marketed. The policy that assist poor farmers in obtaining market skills; create affordable credit service; strengthen community based producer groups and capacitating the females socially and economically in the community believed to minimize the problems encountering small farmers in a way to market their crop

Atoms in Molecules (AIM), Natural Bond Orbital (NBO), and normal coordinate analysis have been carried out at the global minimum structures of TH₅⁺ (T = C/Si/Ge). All these analyses lead to a consistent structure for these three protonated TH₄ molecules. The CH₅⁺ has a structure with three short and two long C-H covalent bonds and no H-H bond. Hence, the popular characterization of protonated methane as a weakly bound CH₃⁺ and H₂ is inconsistent with these results. However, SiH₅⁺ and GeH₅⁺ are both indeed a complex formed between TH₃⁺ and H₂ stabilized by a tetrel bond, with the H₂ being the tetrel bond acceptor. The three-center-two-electron bond (3c-2e) in CH₅⁺ has an open structure, which can be characterized as a V-type 3c-2e bond and that found in SiH₅⁺ and GeH₅⁺ is a T-type 3c-2e bond. This difference could be understood based on the typical C-H, Si-H, Ge-H and H-H bond energies. Moreover, this structural difference observed in TH₅⁺ can explain the trend in proton affinity of TH₄. Carbon is selective in forming a ‘tetrel bond’ and when it does, it might be worthwhile to highlight it as a ‘carbon bond’.

In this letter, it is proposed that cryogenic quantum bits could operate based on the nonlinearity due to the quantum capacitance of two-dimensional Dirac materials, and in particular graphene. The anharmonicity of a typical superconducting quantum bit is calculated and the sensitivity of quantum bit frequency and anharmonicty with respect to temperature are found. Reasonable estimates reveal that a careful fabrication process could reveal the expected properties, thus putting the context of quantum computing hardware into new perspectives.

An increased demand for natural products nowadays most specifically probiotics (PRO) is evident since it comes in conjunction with beneficial health effects for the consumers. In this regard, it is well known that encapsulation could affect positively the PRO's viability throughout food manufacturing and long-term storage. This paper aims to analyze and review various multilayer strategies for encapsulation of PRO. Double-layer encapsulation of PRO by electro-hydrodynamic atomization or electrospray technology has been reported along with layer-by-layer assembly and water-in-oil-in-water (W1/O/W2) double emulsions to produce multilayer PRO-loaded carriers. Finally, their applications in food products are presented. The resistance (cover material) and viability of (PRO) to mechanical damage, during gastrointestinal transit and shelf life of these trapping systems are also described. The PRO encapsulation in double and multiple-layer coatings combined with other technologies can be examined to increase the opportunities for new functional products with amended functionalities opening a novel horizon in food technology.

Opportunistic networks, an evolution of mobile Ad Hoc networks (MANETs), offer decentralized communication without relying on preinstalled infrastructure, enabling nodes to route packets through different mobile nodes dynamically. However, due to the absence of complete paths and rapidly changing connectivity, routing in opportunistic networks presents unique challenges. This paper proposes a novel probabilistic routing model for opportunistic networks, leveraging nodes' meeting probabilities to route packets towards their destinations. The model dynamically builds routes based on the likelihood of encountering the destination node, considering factors such as last meeting time and acknowledgment tables to manage network overload. Additionally, an efficient message detection scheme is introduced to alleviate high overhead by selectively deleting messages from buffers during congestion. Furthermore, the proposed model incorporates cross-layer optimization techniques, integrating optimization strategies across multiple protocol layers to maximize energy efficiency, adaptability, and message delivery reliability. Through extensive simulations, the effectiveness of the proposed model is demonstrated, showing improved message delivery probability while maintaining reasonable overhead and latency. This research contributes to the advancement of opportunistic networks, particularly in enhancing connectivity and efficiency for Internet of Things (IoT) applications deployed in challenging environments.

The ocean’s mixed layer depth (MLD) plays an important role in understanding climate dynamics, especially during extreme weather occurrences like hurricanes. This study investigates the effects of Hurricane Katrina (2005) on the MLD in the Gulf of Mexico, using the Delft3D modeling system. By integrating hydrodynamics and wave dynamics modules, we simulate the ocean’s response to extreme weather, focusing on temperature, salinity and MLD variations. Our analysis reveals significant cooling and mixing induced by Katrina, resulting in spatial and temporal fluctuations in temperature (~± 4°C) and salinity (~± 2.5 ppt). The MLD is estimated using a simple threshold method, revealing a substantial deepening to ~120 m on August 29th-30th during Hurricane Katrina in the middle of northern Gulf of Mexico, compared to an average MLD of ~20-40 m during pre-storm conditions. It took about 18-days to recover to ~84% of the pre-storm level after Katrina. Compared to the stand-alone FLOW model, the coupled FLOW+WAVE model yields a deeper MLD of ~5%. The MLD recovery and wave effect on the MLD provide insights from various scientific, environmental and operational perspectives, offering a valuable basis for ocean management, planning and applications, particularly during extreme weather events.

This paper proposes to combat active eavesdropping by intelligent reflecting surface (IRS) backscatter techniques. To be specific, the source (Alice) sends the confidential information to the intended user (Bob), while the eavesdropper (Willie) transmits jamming signal to interrupt the transmission for more data interception. To enhance the secrecy, an IRS is deployed and connected with Alice through fiber to transform the jamming signal into the confidential signal by employing backscatter techniques. Based on the considered model, an optimization problem is formulated to maximize signal-to-interference-plus-noise ratio (SINR) at Bob under the constraints of the transmit power at Alice, the reflection vector at the IRS and the allowable maximum SINR at Willie. To address the optimization problem, an alternate optimization algorithm is developed. The simulation results verify the achievable secrecy gain of the proposed scheme.

Electroluminescence (EL) is an innovative technology in the lighting area. The EL device's main structure consists of a phosphor layer sandwiched by two electrodes. In this work, several alternating current EL devices have been developed by applying a set of sequential layers with combinations of in-house prepared inks and commercially available ink as a phosphor layer. A flexible polyester textile substrate was functionalized with inks by spray coating technique, after knife-coated an interfacial layer directly on the surface. A thorough study was carried out on the phosphor layer composition to optimize the EL device performance, more precisely the illuminance intensity and the illuminance homogeneity. The developed phosphor layer was composed of zinc sulphide doped with copper (between 30.0 to 38.1 wt%) and diluted by using a diluent at different ratios (28.0 to 35.5 wt%). The best peak illuminance intensity of 61 lux was obtained when the phosphor ink presented 35.4% ZnS:Cu and was diluted with 33.0% diluent. The aim of this study to determine the best formulation of the phosphor layer, which can be highly promising for further developments of EL devices, taking in account different applications in market.

Wearing gloves while operating machinery in workshops is an essential precaution to prevent mechanical injuries and burns from high temperatures, among other potential hazards. Ensuring workers are properly equipped with gloves, which is a crucial measure in accident prevention. Glove images often occupy a minimal proportion of the frame and are easily obscured by cluttered backgrounds, especially with limited edge computing resources. Consequently, this study proposes a glove detection algorithm called YOLOv8-AFPN-M-C2f based on YOLOv8, offering swifter detection speeds, lower computational demands, and enhanced accuracy for workshop scenarios. This research innovates by substituting the head of YOLOv8 with the AFPN-M-C2f network, amplifying the pathways for feature vector propagation, and mitigating semantic discrepancies between non-adjacent feature layers. Additionally, the introduction of a superficial feature layer enriches surface feature information, augmenting the model's sensitivity to smaller objects. To assess the performance of the YOLOv8-AFPN-M-C2f model, we conducted multiple experiments using a factory glove detection dataset compiled for this study. The results indicate that the enhanced YOLOv8 model surpasses other network models. Compared to the baseline YOLOv8 model, the refined version shows a 2.6% increase in mAP@50%, a 90.1% rise in FPS, and a 13% reduction in the number of parameters. This research contributes an effective solution for the detection of glove adherence.

Calcium sulfate (CS) materials containing terbium ions at 0, 1.0, or 2.0 mol.% were obtained by mechanochemical synthesis. According to X-ray diffraction data, the powder materials are characterized by the presence of a CaSO4×0.5H2O phase, while Tb3+ is incorporated into the lattice at ≤1.0 mol.%. Specific surface area enlarged from 2.1 to 22.5 m2/g as crystallite size decreased from 68 to 31 nm and the Tb3+ concentration increased up to 1.0 mol.%. Thermal analysis showed that terbium slightly raises the temperature of CaSO4×2H2O-to-CaSO4 transition. The presence of Tb3+ did not affect the solubility of the CS cements. Furthermore, after 7 days of soaking of the materials in a simulated body fluid, a calcium phosphate layer formed corresponding to a hydroxyapatite phase, in contrast to the pure cements. Luminescent properties were studied by excitation at 276 nm. The recorded emission peaks of the CS materials indicated that the luminescence of the samples is green and blue, with the most intense luminescence observed for samples containing 1.0 mol.% Tb3+. The developed materials can find applications in medicine as bioimplants for the regeneration and restoration of bone tissue with a possibility of noninvasive monitoring of the bone restoration process.

This study focuses on the analyses of nano-twinned Copper (Cu) films deposited through magnetron sputtering on Silicon Carbide (SiC) chips. The investigation encompasses the utilization of Chromium (Cr) adhesive layer coupled with varying voltage bias conditions. The goal is to comprehensively examine the influence of adhesive layer and negative bias voltages, contributing to an enhanced understanding of materials engineering and bonding technologies for advanced applications. The formation of a nanotwinned structure and (111) surface orientation can be properly controlled by applied substrate bias. High density nanotwinned structures were introduced into Cu films sputtered on SiC substrates with 82.3% of (111)-orientation proportion at -150 V much higher than the Cu film sputtered with another substrate bias. It is concluded that the sputtered Cu nanotwinned film formed with -150 V bias voltage has the potential to be employed as the interlayer for low temperature direct bonding.

The flow around thick airfoils at low Reynolds numbers and the possibility of using energy methods to control flowfield, increase lift and reduce drag are considered. For calculations, a series of propulsion airfoils is used, obtained by a combination of solving the inverse problem of aerodynamics and stochastic methods of global optimization. The calculations take into account the transition from the laminar flow regime to the turbulent one, which has a significant effect on the lift and airfoil drag. The applicability of various turbulence models for airfoil modelling at low Reynolds numbers is discussed. The results of numerical simulation make it possible to determine the dependence of the lift coefficient on the angle of attack and the optimal flow rate of air taken from the airfoil surface for each angle of attack. The results of numerical simulation are compared with the data of a physical experiment, and conclusions are drawn about the accuracy of various turbulence models.

Nano- and micro-sized CeO2 surface layers based on titanium alloy TiAl6V4 were obtained by magnetron sputtering with or without subsequent annealing. The structure of the samples was determined using scanning electron microscopy, Auger electron spectroscopy, energy dispersive spectroscopy, and X-ray diffraction. Hardness was measured by sclerometry. A direct linear dependence of the thickness of the surface layers on the deposition time and an extreme dependence, passing through a maximum, on the power are shown. A decrease in hardness with an increase in the thickness of the cerium oxide coating was noted. An increase in surface roughness, delamination and loosening of the surface layer, presumably associated with annealing, were noted. In samples with a surface layer thinner than 715 nm without annealing and 750 nm after annealing, the formation of a sublayer of TiO2, Al2O3, and Ce(VO4) was found, and in annealed samples with a layer length of less than 300 nm, all cerium dioxide reacted with vanadium dioxide to form vanadate.

In the past decade, considerable efforts have been devoted to the development of semitransparent organic solar cells. Numerous materials and architectures have been proposed for the future commercialization of these devices. Among these, the use of ternary active layers demonstrated a great promise for the development of efficient semi-transparent organic solar cells with the potential for future applications including self-powered greenhouses and powered windows. Researchers seek alternative solutions to the trade-off between device power conversion efficiency (PCE) and average visible transmittance (AVT), with photoactive materials being the key parameters that govern both (PCE) and (AVT) as well as device stability. Several new organic materials, including polymers and small molecules, were synthesized, and used in conjunction with a variety of techniques to achieve semitransparent conditions. In this review paper, we will look at the working principle and key parameters of semi-transparent organic solar cells, as well as the methods that have been used to improve the performance of ternary-based semi-transparent organic solar cells. The main approaches were concluded to be spectral enhancement and transparency increment of the active layer through bandgap tuning, utilizing novel organic semiconductors, and design architecture of the active layers.

Graphene nanostructures (GNS) are among the most promising materials for creating supercapacitors. However, GNS are still not used in creating supercapacitors due to the impossibility of obtaining large volumes of high-quality material at an acceptable cost. In this work, we investigated the efficiency of using few-layer graphene (FLG) with the number of layers is not more than 5 synthesized under Self-propagating high-temperature synthesis (SHS) conditions as basic material for supercapacitors. Using the SHS process makes it possible to synthesize large volumes of FLG without Stone-Wales defects. It was found that the synthesized FLG makes it possible to obtain better results than using classical materials, namely activated carbon (AC). It was found that the sample based on FLG has a higher specific capacitance – 65 F×g-1 compared to the sample from AC, the specific capacitance of which is 35 F×g-1, for a speed of 5 mV×s-1 these values are 170 and 64 F×g-1, respectively. The drop in capacitance over 1000 cycles was 4%, which indicates a sufficiently high stability of FLG and allows us to consider FLG as perspective material for use in supercapacitors.

Delayed atomic layer deposition (ALD) of ZnO, i.e., area selective (AS)-ALD, was successfully achieved on silicon wafers (Si/SiO2) terminated with tris(dimethylamino)methylsilane (TDMAMS). This resist molecule was deposited in a home-built, near atmospheric pressure, flow-through , gas-phase reactor. TDMAMS has been shown to react with Si/SiO2 in a single cycle/reaction and to drastically reduce the number of silanols that remain at the surface. ZnO was deposited in a commercial ALD system using dimethylzinc (DMZ) as the zinc precursor and H2O as the coreactant. Deposition of TDMAMS was confirmed by spectroscopic ellipsometry (SE), X-ray photoelectron spectroscopy (XPS), and wetting. ALD of ZnO, including its selectivity on TDMAMS – terminated Si/SiO2 (Si/SiO2/TDMAMS), was confirmed by in situ ellipsometry, ex situ SE, XPS, and/or high sensitivity – low energy ion scattering (HS-LEIS). The thermal stability of the TDMAMS resist layer, which is an important parameter for AS-ALD, was investigated by heating Si/SiO2/TDMAMS in air and nitrogen at 330 ºC. ALD of ZnO takes place more readily on Si/SiO2/TDMAMS heated in the air than in N2, suggesting greater damage to the surface heated in the air. To better understand the in situ ALD of ZnO, the data were also plotted as the normalized growth per cycle and to show the selectivity. Even one, short pulse of TDMAMS effectively passivates Si/SiO2. TDMAMS can be an effective small molecule inhibitor of ALD of ZnO on Si/SiO2 surfaces.

At present, nanomaterials (NMs) show extreme potential for a wide range of applications ranging from aerospace to energy storage applications owing to a number of properties which, in a number of contexts have been reported to be superior as compared to those of bulk counterparts. However, the high surface area to volume ratio which yields extraordinary properties to NMs also turns out to be the major limitation in a number of different contexts. For instance, the high surface area to volume ratio in these materials leads to a high reactivity, especially in electrochemical environments which are prevalent during energy storage applications. In this context, it is worthwhile mentioning that processing of NMs play a crucial role in influencing their mechanical properties. On the other hand, surface engineering has emerged as a powerful tool to deconvolute bulk properties from surface characteristics and has been reported to exhibit tremendous potential for overcoming the aforementioned limitation of NMs. The present review therefore, is aimed at highlighting the present status of research in the field of processing and applications of surface engineered NMs. Moreover, challenges and future perspectives in the aforementioned avenue have been discussed.