An analysis of the features of measurements and correction of phase distortions in optical waves propagating in the atmosphere at various levels of turbulence was performed. It is shown that with increasing intensity fluctuations, the limiting capabilities of phase correction decrease, and the phase of an optical wave that has passed through a turbulence layer consists of two components: potential and vortex. It was found that even in the region of weak fluctuations there is an overlap of spectral filtering functions for intensity and phase fluctuations. Areas of turbulence inhomogeneities have been identified that will have mutual influence and negatively affect the operation of the phase meter. It is noted that correlation functions, both phase and intensity, are less susceptible to this compared to structural functions. The results of experimental studies of the reconstruction of the wavefront of laser radiation distorted by atmospheric turbulence using a Shack-Hartmann wavefront sensor during vignetting and central screening of the entrance pupil of the optical system are presented. Studies have been carried out on the propagation of laser radiation along a horizontal atmospheric path for various levels of turbulence. The results are analyzed in terms of Zernike polynomials.

Phase synchronization of weakly coupled limit cycle oscillators are related to the stability of the zero solution of the reduced-order dynamics of phase differences, represented by a systems of differential equations on a hypertorus. Using Rantzer's density function, a dual form of Lyapunov function, we propose a method to certify almost global stability of an equilibrium on a hypertorus. We show that the proposed method can certify robustness of phase synchronization of all-to-all and weakly coupled limit cycle oscillators with respect to disturbances in phases. The method leverages sum of squares polynomial optimization to construct the certification function.

To enhance the mechanical properties (i.e. strength and elongation) of the face-centered cubic (fcc) α-phase in the Au-Cu-Al system, this study focused on the introduction of the martensite phase (doubled B19 (DB19) crystal structure of Au2CuAl) via the manipulation of alloy compositions. Fundamental evaluations, such as microstructure observations, phase identifications, thermal analysis, tensile behavior examinations, and reflectance analysis have been conducted. The presence of fcc annealing twins was both observed in the optical microscope (OM) and the scanning electron microscope (SEM) images. Both the strength and elongation of the alloys were greatly promoted while the DB19 martensite phase was introduced into the alloys. Amongst all the prepared specimens, the 47Au41Cu12Al and the 44Au44Cu12Al alloys performed the optimized mechanical properties. The enhancement of strength and ductility in these 2 alloys was achieved while the stress plateau was observed during the tensile deformation. A plot of the ultimate tensile strength (UTS) against fracture strain was constructed to illustrate the effects of the introduction of the DB19 martensite phase on the mechanical properties of the alloys. Regardless of the manipulation of the alloy compositions and the introduction of the DB19 martensite phase, the reflectance stayed almost identical to pure Au.

The phase composition design principle is introduced to obtain balanced properties of ionic conductivity and thermo-tolerant for zirconia solid electrolytes used in solid oxide fuel cells (SOFCs). The zirconia ceramic solid electrolytes are fabricated by two-step free sintering. With increasing Y/Mg ionic ratio from 1.78:1 to 1.88:1, the content of monoclinic phase fluctuates little (±3%). The ionic conductivity, including the total electrical resistance; grain electrical resistance and grain boundary electrical resistance at 1223K, are all gradually declining with the increasing of Y/Mg ionic ratio. Furthermore, the enrichment of Mg ion in grain boundary acts as a disincentive to grain boundary ionic conductivity. In addition, the maximum total equivalent conductivity at 1223K in this study reaches to 0.143 Scm-1 which can compare with that of certain YSZ. It will be beneficial to SOFCs application profited from increasing ionic conductivity of ceramic solid electrolytes.

The availability of sufficient amounts of form I of benzocaine has led to the investigation of its phase relationships with the other two existing forms II and III using adiabatic calorimetry, powder X-ray diffraction, and high-pressure differential thermal analysis. The latter two forms were known to have an enantiotropic phase relationship with form III stable at low-temperature and high-pressure, while form II is stable at room temperature. Using adiabatic calorimetry data, it can be concluded, that form I is the stable low-temperature, high-pressure form, which also happens to be stable at room temperature; however, form II, due to its persistence at room temperature, is still the most convenient polymorph to use in formulations. Form III presents a case of overall monotropy and does not possess any stability domain in the pressure-temperature phase diagram. Heat capacity data for benzocaine have been obtained by adiabatic calorimetry from 11 K up to 369 K above its melting point, which can be used to compare to results from in-silico crystal structure prediction.

Phase imaging of biochemical samples has been demonstrated for the first time at the Infrared Microspectroscopy (IRM) beamline of the Australian Synchrotron using the usually discarded Near-IR (NIR) region of the synchrotron-IR beam. The synchrotron-IR beam at the Australian Synchrotron IRM beamline has a unique fork shaped intensity distribution as a result of the gold coated extraction mirror shape, which includes a central slit for rejection of the intense X-ray beam. The resulting beam configuration makes any imaging task challenging. For intensity imaging, the fork shaped beam is usually tightly focused to a point on the sample plane followed by a pixel-by-pixel scanning approach to record the image. In this study, a pinhole was aligned with one of the lobes of the fork shaped beam and the Airy diffraction pattern was used to illuminate biochemical samples. The diffracted light from the samples was captured using a NIR sensitive lensless camera. A rapid phase-retrieval algorithm was applied to the recorded intensity distributions to reconstruct the phase information corresponding to different planes. The preliminary results are promising to develop multimodal imaging capabilities at the IRM beamline of the Australian Synchrotron.

As novel materials for carbon capture, phase change solvents can separate into two immiscible phases during the CO2 capturing procedure under a certain temperature. The solvent systems can significantly decrease the energy consumption since the solvents can be regenerated by only heating the rich-CO2 phase. In this work, amino acid ionic liquids (AAILs) were synthesized using quaternary ammonium salts and amino acids as raw materials, and the aqueous solutions were prepared as novel liquid-solid phase change solvents. The results showed that the solvents had excellent CO2 absorption capacity, and the AAILs functionalized by glycine and tryptophan exhibited significant phase change properties. The mechanism of phase-change of the solvent were mainly due to the lower solubility of the product after reaction between AAILs and CO2. The solvent with tryptophan as anion could be regenerated by only heating the CO2-riched solid phase, which might significantly decrease energy consumption of regeneration. And the absorbent could be reused with the regenerated absorption ratio up to 79%. The solvent system has great potential in industrial application due to the easy operation process and efficient recycling ability.

Numerical models widely used for hydrocarbon phase behavior and compositional flow simulations are based on assumption of thermodynamic equilibrium. However, it is not uncommon for oil and gas-condensate reservoirs to exhibit essentially non-equilibrium phase behavior, e.g., in the processes of secondary recovery after pressure depletion below saturation pressure, or during gas injection, or for condensate evaporation at low pressures. In many cases the ability to match field data with equilibrium model depends on simulation scale. The only method to account for non-equilibrium phase behavior adopted by the majority of flow simulators is the option of limited rate of gas dissolution (condensate evaporation) in black oil models. For compositional simulations no practical yet thermodynamically consistent method has been presented so far except for some upscaling techniques in gas injection problems. Previously reported academic non-equilibrium formulations have a common drawback of doubling the number of flow equations and unknowns compared to the equilibrium formulation. In the paper a unified thermodynamically-consistent formulation for compositional flow simulations with non-equilibrium phase behavior model is presented. Same formulation and a special scale-up technique can be used for upscaling of an equilibrium or non-equilibrium model to a coarse-scale non-equilibrium model. A number of test cases for real oil and gas-condensate mixtures are given. Model implementation specifics in a flow simulator are discussed and illustrated with test simulations. A non-equilibrium constant volume depletion algorithm is presented to simulate condensate recovery at low pressures in gas-condensate reservoirs. Results of satisfactory model matching to field data are reported and discussed.

Clopidogrel is one of the thienopyridine antiplatelet drugs commonly used as a prophylactic medication to prevent coagulation in vessels and cardiovascular events. The molecule of clopidogrel is metabolized in the liver via phase-I and phase-II metabolism pathways. The sulfenic acid clopidogrel metabolite undergoes phase-II metabolism through conjugation with glutathione by the glutathione-s-transferase (GST) to form a glutathione conjugate of clopidogrel (inactive metabolite). A glutaredoxin enzyme removes the glutathione conjugated with clopidogrel to form cis-thiol-clopidogrel. This review focused on the polymorphisms of genes related to phase-II metabolism during the clopidogrel bioactivation process. Overall, no well-controlled studies were done about the relationship between the clopidogrel bioactivation process and genes related to phase-II metabolism’s enzymes. Nevertheless, some polymorphisms of G6PD, GCLC, GCLM, GSS, GST, GSR, HK, and GLRX genes could be responsible for clopidogrel resistance due to low glutathione conjugate or glutaredoxin plasma levels. Studies needed to be concerned with the relationship between clopidogrel resistance and phase-II metabolism issues in the near future.

In Chronic Myeloid Leukemia (CML) patients, CD34+/CD38-/CD26+ cell population represents a “CML specific” Leukemia Stem Cell (LSC) compartment. Indeed, preliminary studies showed that the expression of CD26 discriminates bone marrow CML Leukemic Stem Cells (LSCs) from nor-mal Hematopoietic Stem Cells (HSCs) or from LSCs of other myeloid neoplasms. We were first to demonstrate that at diagnosis CD34+/CD38-/CD26+ cells are easily measurable also in Peripheral Blood (PB) and that residual circulating CD26+LSCs persist, with a fluctuating trend, in most pa-tients in optimal response during treatment with Tyrosine Kinase Inhibitors (TKIs) and even after successful TKI discontinuation. These data corroborate and confirm the possibility of using flow-cytometry CD26+ evaluation as an important diagnostic tool that, combined with molecular biology and cytogenetic, could provide a rapid diagnosis of Chronic Phase (CP) CML starting from a simple PB sample. Yet, few data are available regarding the behavior of CD26+LSCs during Accelerated Phase (AP) or Blast Phase (BP) CML and the role, if any, this peculiar staminal cell compartment may play in disease progression. In the present study we compared the presence and phenotypic characteristics of circulating CD26+LSCs in CP CML patients at diagnosis, during AP and in cases of progression to lymphoid BP, inquiring a possible role of these cells during dis-ease evolution.

Cyclin dependent kinase 1 (CDK1) has been primarily identified as a key cell cycle regulator in both mitosis and meiosis. Recently, an extramitotic function of CDK1 emerged when evidence was found that CDK1 is involved in many cellular events that are essential for cell proliferation and survival. In this review we summarize the involvement of active CDK1 in the initiation and elongation steps of protein synthesis in eukaryotes. During its activation CDK1 influences the initiation of protein synthesis, promotes the activity of specific translational initiation factors and affects the functioning of a subset of elongation factors. Our review provides insights into gene expression regulation during the transcriptionally silent cell cycle/M-phase and describes quantitative and qualitative translational changes based on the extramitotic role of the cell cycle master regulator CDK1, to optimize temporal synthesis of proteins to sustain division-related processes: mitosis and cytokinesis.

Future, flexible thermal energy conversion systems require new, demand-optimized high-performance materials. The High performance Ferritic (HiperFer) stainless steels, under development at the Institute of Microstructure and Properties of Materials (IEK-2) at Forschungszentrum Jülich GmbH in Germany, provide a balanced combination of fatigue, creep and corrosion resistance at reasonable price. This paper outlines the scientific background of alloy performance development, which resulted in an age-hardening ferritic, stainless steel grade. Furthermore, technological properties are addressed and the potential concerning application is estimated by benchmarking versus conventional state of the art materials.

Despite multiple classical outcomes arising from the quantum Rayleigh conversions of photons underlying the propagation of optical waves through dielectric media and the ensuing light-matter interactions, this quantum process has been largely ignored. Several of its outcomes are considered in this article from a physical perspective, e.g., inter-quadrature coupling of photons, phase-dependent amplification in optical directional couplers and related polarization rotation, phase-shifting of weak signals in the optically linear regime, location-dependent coupling coefficient for refractive index gratings, etc. A correct identification of these effects will enable useful design and operation of integrated photonic functional devices.

Recently, ice with the stacking disorder structure, consisting of random sequences of cubic ice (Ic) and hexagonal ice (Ih) layers, is reported to be more stable than pure Ih/Ic. While, due to a much lower free energy barrier of heterogeneous nucleation, in practice, the freezing process of water is usually controlled by heterogeneous nucleation which is triggered by an external medium. Herein, molecular dynamic simulations were carried out to explore the polymorph dependence of ice on the lattice structure of substrates. It turns out that, during the nucleation stage, the polymorph of ice nuclei can be severely altered by the graphene substrate, on which the Ih was found to occupy an absolute majority in new-formed ice. This can be attributed to the structure similarity between graphene and basal face of Ih. Besides the nucleation stage, our results suggest that the substrate can not affect the polymorph of ice which is far from the graphene surface. The polymorph selectivity of graphene to Ih will diminish with the growth of ice layer.

It is widely, but not universally, believed that the lipids of the plasma membrane are not uniformly distributed, but that "rafts'' of sphingolipids and cholesterol float in a "sea'' of unsaturated lipids. The physical origin of such heterogeneities is often attributed to a phase coexistence between the two different domains. We argue that this explanation is untenable for several reasons. Further we note that the results of recent experiments are inconsistent with this picture. However they are quite consistent with an alternate explanation, namely that the plasma membrane is an emulsion of the two kinds of regions. To show this, we briefly review a simplified version of this theory and its phase diagram. We also explicate the dependence of the predicted domain size on four physical parameters. Among them are the spontaneous curvature of the membrane and its bending modulus and surface tension. Taking values of the latter two from experiment, we obtain domain sizes for several different cell types that vary from 58 to 88 nm.

Spatial and temporal variation of the free electron concentration in the ionosphere affects SAR interferograms, in particular at low radar frequencies. In this work the identification, estimation and compensation of ionospheric path delay phases in PALSAR-3 and NISAR-L interferograms is discussed. Both these L-band sensors acquire simultaneously SAR data in a main spectral band and in an additional, spectrally separated, narrower second band to support the mitigation of ionospheric path delays. The methods presented permit separating the dispersive and the non-dispersive phase terms based on the double-difference interferogram between the two available spectral bands and the differential interferogram of the main band. The applicability of the proposed methods is demonstrated using PALSAR-3-like data that was simulated based on PALSAR-2 SM1 mode data.

In view of the limitations of the existing eccentricity error separation method of the rotary table, an eccentricity error separation method based on the phase feature of the moiré signal of single reading head is proposed herein. A grating pair transmission model is established based on the analysis of the principle of the rotary table, thereby the influence of eccentricity error on the phase feature of the moiré signal in the rotation course of the rotary table is clarified, and the corresponding model between the phase feature spectral components and the eccentricity error is established. The verification experiments of the proposed method are carried out based on the laboratory-made circuit system. After verifying the accuracy of the data acquisition of the laboratory-made circuit board, the verification experiments of the eccentricity error separation effect of the proposed method are carried out. The experimental data are compared with those of the traditional method and the results show that the error between the two methods is 2.34μm and the relative error is 2.3%.

The TanDEM-X mission is acquiring a new dataset to provide a temporally independent DEM, called "TanDEM-X Change DEM". This set of acquisitions taken between 2017 and 2020 has a clear temporal separation to the TanDEM-X global DEM data which were acquired between 2010 and 2015. Therefore, this new DEM aims to enable the characterization of terrain changes. Improvements in the acquisition planning and the data processing were necessary to generate this Change DEM with fewer acquisitions but still very high accuracy. For this, the use of an edited TanDEM-X DEM as a "starting point" for the interferometric processing is mandatory.

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.

Reversed Flow Gas Chromatography (R.F.G.C.) was employed to assess the impact of genetic modification on Saccharomyces cerevisiae yeast strains during the process of alcoholic fermentation, utilizing fig syrup. Multiple fermentations were carried out at various temperatures to evaluate the influence of genetic modifications on yeast strain efficiency. The study involved a wild-type yeast strain, W303, as a control, and two genetically modified strains, W_M4_533 and W_M4_558, sharing the same genetic background as the wild type. Notably, the genetic modifications in the Msn4p transcription factor involved the substitution of serine residues with alanine at positions 533 and 558, resulting in the development of psychrophilic or ethanol-resistant strains. Utilizing the R.F.G.C. method enabled the differentiation of the duration of alcoholic fermentation phases, providing insights correlated to the yeast cell life cycle. The values of rate constants (k) for each phase, conducted with both wild-type and genetically modified cells using RFGC, aligned with existing literature. Additionally, the calculation of activation energies for distinct phases revealed lower values for genetically modified strains compared to wild-type strains. This decrease in activation energies suggests enhanced efficiency in the alcoholic fermentation process for the genetically modified strains.

Rapid solidification during metal additive manufacturing (AM) leads to non-equilibrium microsegregation, which can result in the formation of detrimental phases and cracking. Most of the microsegregation models, assume a Scheil-type solidification, where the solidification interface is planar and there exists local equilibrium at the interface along with either zero or infinite solute diffusion in the respective participating phases - solid and liquid. This assumption leads to errors in prediction. One has to account for finite solute diffusion and the curvature at the dendritic tip for more accurate predictions. In this work, we compare different microsegregation models that do and do not consider finite diffusion and dendrite tip kinetics against the experiments. We also propose a method to couple dendrite tip kinetics with the diffusion module (DICTRA®) implemented in Thermo-Calc®. The models which accounted for both finite diffusion and dendrite tip kinetics matched well with the experimental data.

MoS2 has long been considered as a promising catalyst for hydrogen production. At present, there are many strategies to further improve its catalytic performance, such as edge engineering, defect engineering, phase engineering and so on. However, at present, there is still a great deal of controversy about the mechanism of MoS2 catalytic hydrogen production. For example, it is generally believed that the base plane of MoS2 is inert, but it has been reported that the inert base plane can undergo a transient phase transition in the catalytic process to play the catalytic role, which is contrary to the common understanding that the catalytic activity is only at the edge. Therefore, it is necessary to further understand the mechanism of MoS2 catalytic hydrogen production. In this article, we summarized the latest research progress on the catalytic hydrogen production of MoS2, which is of great significance for revisited the mechanism of MoS2 catalytic hydrogen production.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

We investigated the structural evolution of the two-phase blends of polycarbonate (PC) and poly(methyl methacrylate) (PMMA) at various blend compositions by simultaneous biaxial stretching using optical microscopy and SEM observation. The spherical PMMA domains and PC matrix in 30/70 PC/PMMA were enlarged uniformly at all in-plane direction, while the anisotropic-shaped co-continuous structure in 50/50 PC/PMMA was deformed to crosshatched one by in-plane bimodal orientation. In 70/30 PC/PMMA, the phase inversion was found to occur by simultaneous biaxial stretching; i.e., the spherical PMMA domains were changed to crosshatched matrix by in-plane bimodal orientation due to coalescence of the PMMA domains during the stretching. Owing to the phase inversion, the surface hardness estimated by pencil hardness test became harder from 2B to 2H with increasing the strain from 1.0 to 2.0.

The precipitate phases often play an important influence on the corrosion resistance of 2205 Duplex stainless steel (DSS). In the presented paper, the microstructure and corrosion resistance in the hot-rolled and cold-rolled 2205 DSS aging for different time at 850 °C was investigated by XRD, SEM and potentiodynamic polarization. It has been found that the Chi(χ) phase and Sigm(σ) phase were precipitated in turn after aging treatment of hot-rolled and cold-rolled materials, but the precipitate amount in cold-rolled material is much more than that of hot-rolled samples. The corrosion resistance of the solution-annealed cold-rolled material is similar to the hot-rolled material, but the corrosion resistance of cold-rolled material with precipitate is weaker than that of hot-rolled material after aging treatment. Pitting initiates preferentially in the Cr-depleted region from σ phase in aged hot-rolled 2205, and severe selective corrosion occurs on sigma/ferrite interfaces aged for a long aged lime. However, the initiation of pitting corrosion may take place at the phase boundary, defect and martensite in the aged cold-rolled 2205. The σ phase is further selectively dissolved by electrochemical method to investigate the difference of microstructure and corrosion behavior in hot-rolled and cold-rolled 2205 duplex stainless steel.

The influence of pH, temperature, biopolymer ratio, total concentration, and ionic concentration on the interaction between egg white protein (EWP) and chitosan (CS) was investigated through turbidity, zeta potential, and state diagram in our research. In addition, phase behavior was observed under various conditions. The turbidity of EWP remained low (turbidity<0.03) and basically unchanged at a wide range of pH (4.0-8.0), while the turbidity of CS was slightly higher (turbidity<0.2) after pH 7.0 than before. Moreover, under the same conditions, a sharply rising peak pattern was observed for the complex between EWP and CS. The maximum turbidity value was observed at 55°C, and the temperature had a mild effect on turbidity. The optimum EWP to CS ratio was found to be 12:1 based on the experiment of the turbidity curves and state diagrams influenced by different biopolymer mixing ratios. With the enhanced concentrations of total biopolymer, the maximum turbidity rose insignificantly above 0.1%.

The organo-catalyzed enantioselective benzylation reaction of α-trifluoromethoxy indanones afforded α-benzyl-α-trifluoromethoxy indanones with a tetrasubstituted stereogenic carbon center in excellent yield with moderate enantioselectivity (up to 57% ee). Cinchona alkaloid-based chiral phase transfer catalysts were found to be effective for this transformation, and both enantiomers of α-benzyl-α-trifluoromethoxy indanones were accessed, depended on the use of cinchonidine and cinchonine-derived catalyst. The method was extended to the enantioselective allylation reaction of α-trifluoromethoxy indanones to give the allylation products in moderate yield with good enantioselectivity (up to 76% ee).

Linear state estimation (SE) formulation under a rectangular coordinate system has been proved to be applicable for real-time distribution network management. Micro phasor measurements’ model can be accommodated into this kind of SE easily. However, voltage magnitude, active power and reactive power measurements are transformed to linear measurements with large node voltage error. To cope with this issue, a linear state estimation under a polar coordinate system is adopted at the first stage to obtain accurate enough complex node voltage, and then nonlinear measurements are transformed to be linear with complex node voltage. At the second stage, linear SE under a rectangular coordinate system can be adopted to satisfy more strict network constraints. The proposed two-stage linear SE is validated on balanced 14, 33, 70,84, 119, 135 nodes network and IEEE 13, 34, 37,123 unbalanced test feeders.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

Interface between matrix/coating or coating/coating in fact represents a very complicate thin interfacial layer. So interface model is necessary to avoid the difficulty on considering such a complicate thin layer in analysis. Classic interface model and cohesive model have been widely used in stress analysis of coating materials, though they cannot represent the effect of very thin interfacial layer accurately. A complete interface model has been deduced from the equivalent constitutive of interfacial layer in this paper. It is found that both classic interface model and cohesive model sometimes cannot give correct analysis results, while the complete interface model can always give a correct result. Moreover, the stress parallel to interface within the interfacial layer can also be analyzed by the new model. Besides, this model can also be used to describe the equivalent properties of interfacial layer, thereby, can provide a quantitative characterizing method for interfacial layer itself.

Outbreaks of the desert locust Schistocerca gregaria affect some of the poorest parts of Africa, causing devastating catastrophes. Key to understanding and dealing with this problematic adaptation to environmental changes is comparing locusts that are gregarious (associated with outbreak states) and solitarious (associated with non-outbreak states) either in nature or after experimental treatments in laboratories. Categorising locusts and detecting changes in their phase status is key to such comparisons. Such comparisons are hitherto based on applying mathematical models that use behavioural parameters and that each laboratory has to build a new for each experiment. All such models used thus far for research on locusts are different from each other. That implies differences in the tools used for the different experiments and by the different laboratories and, thus, potential noise in the scientific results and interpretations too. Standardizing the way how we categorise locusts between laboratories and experiments is needed if we want to reduce noise and errors. It is even a must if we are to make the results and interpretations transferable and comparable between experiments and laboratories that work in such an important research area. Here, we use samples from independent S. gregaria population in order to further test the two models that were suggested earlier as standardizing tools for S. gregaria categorization. The outcomes of both models were largely replicated and reproducible. We report on how successful the two models were at categorizing solitarious, intermediate (transient) and gregarious nymph and adult samples. We highlight shortcomings and make more specific recommendations on the use of these models based on the differences they show as to their precision when categorizing the solitarious and gregarious S. gregaria nymph and adult samples.

The objective of this study was to identify circulating miRNAs affected by disease duration in newly diagnosed children with type 1 diabetes. Forty children and adolescents from The Danish Remission Phase Cohort were followed with blood samples drawn at 1, 3, 6, 12 and 60 months after diagnosis. Pancreatic autoantibodies were measured at each visit. Cytokines were measured only the first year. miRNA expression profiling was performed by RT-qPCR and quantified for 179 human plasma miRNAs. The effect of disease duration was analyzed by mixed models for repeated measurements, adjusted for sex and age. Eight miRNAs (hsa-miR-10b-5p, hsa-miR-17-5p, hsa-miR-30e-5p, hsa-miR-93-5p, hsa-miR-99a-5p, hsa-miR-125b-5p, hsa-miR-423-3p and hsa-miR-497-5p) were found to significantly change expression (adjusted p-value < 0.05) with disease progression. Three pancreatic autoantibodies ICA, IA-2A, GADA65 and 4 cytokines IL-4, IL-10, IL-21, IL-22 were associated with the miRNAs at different time points. Pathway analysis revealed association with various immune-mediated signaling pathways. Eight miRNAs, involved in immunological pathways changed expression levels during the first five years after diagnosis in children with type 1 diabetes, and were associated with variations in cytokine and pancreatic antibodies, suggesting a possible effect on the immunological processes in the early phase of the disease.

The conformations of trifluoroacetyl triflate, CF3C(O)OSO2CF3, were investigated through vibrational experimental methods (gas-phase FTIR, liquid-phase Raman, and Ar-matrix FTIR spectroscopy) and Density Functional Theory (DFT) calculations. A potential energy surface was computed using the B3P86 /6-31+g(d) approximation as a function of the dihedral angles τ1 = CCOS and τ2 = COSC. The surface reveals three minima, which were further optimized using the B3LYP method with various basis sets (6-31++G(d), 6-311++G(d), tzvp and cc-pvtz). The global minimum corresponds to a syn-anti conformer (the CO double bound syn with respect the O−S single bond and the C−O single bond anti with respect to de S−C single bond). The other two minima represent enantiomeric syn-gauche forms. The Ar-matrix FTIR spectrum exhibited clear evidence of the presence of two conformers. Furthermore, the randomization process observed following broad-band UV-visible irradiation facilitated the identification of the IR absorption of each conformer. Based on the Ar-matrix FTIR experiments, the vapour phase of trifluoroacetyl triflate at room temperatures was composed of approximately 60-70% of the syn-anti conformer and 30-40% of the syn-gauche form.

In the past decades, one of the most widely reported phenomena on Caribbean reefs is the general fall in coral cover and rise in macroalgae. Reefs with low coral cover and high macroalgal abun-dances are often presumed to provide poorer ecosystem functions and services. In this study, we assessed the condition of coral reefs on the Caribbean Coast of Costa Rica and determined how eight key ecosystem metrics varied in response to differential coral and fleshy macroalgae covers. Most reefs surveyed had high fleshy macroalgae and low live coral covers, with an average (± SD) of 31 ± 28% and 14 ± 13% per site. We found that the rugosity, urchin density, fish richness, total fish biomass, large fish density, and the potential fishery value of the reef were higher in sites with low fleshy macroalgae covers (>10%). The value of many of the ecosystem metrics estimated for coral reefs of the region appears to be lower than what’s been reported for other areas in the Caribbean, which may be related to the high macroalgae covers found on the reefs. Our results concur with the prevailing paradigm that an increase in macroalgae abundance could reduce the ecosystem services provided by coral reefs.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

The intention of this paper is to elucidate new types of heat engines with extraordinary efficiency, more specifically to eventually focus on the author’s research into a temporary magnetic remanence device. First we extend the definition of heat engines through a diagrammatic classification scheme and note a paradoxical non-coincidence between the Carnot, Kelvin-Planck and other forms of the 2nd Law, between sectors of the diagram. It is then seen, between the diagram sectors, how super-efficient heat engines are able to reduce the degrees of freedom resulting from change in chemical potential, over mere generation of heat; until in the right sector of the diagram, the conventional wisdom for the need of two reservoirs is refuted. A brief survey of the Maxwell Demon problem finds no problem with information theoretic constructs. Our ongoing experimental enquiry into a temporary magnetic remanence cycle using standard kinetic theory, thermodynamics and electrodynamics is presented – yet a contradiction results with the 2nd law placing it in the right sector of the classification diagram.

An atomic-scale approach is employed to simulate the formation of precipitates with different lattice misfits in the early stages of aging of supersaturated aluminum alloys. Simulation results reveal that the increase of lattice misfit could significantly promote the nucleation rate of precipitates, which results in a larger number and smaller size of the precipitates. The morphologies of the precipitates also vary with the degree of lattice misfit. Moreover, the higher the lattice misfit, the earlier the nucleation of the second phase occurs, which can substantially inhibit the movement of dislocations. The research on the lattice misfit of precipitation can provide theoretical guidance for the design of high-strength aluminum alloy.

Fracture of viscoplastic materials is a complex process due to its time-dependent and plastic responses. Numerical simulation for fracture plays a significant role in crack prediction and failure analysis. In recent years, the phase field model is becoming a competitive approach to predict crack growth and has been extended to inelastic materials such as elasto-plastic, viscoelastic and viscoplastic materials, etc. However, the contribution of inelastic energy to crack growth is seldom studied. For this reason, we implement the phase field model coupled with a viscoplastic constitutive in finite element framework, in which the elastic energy and inelastic energy are used as crack driving energy. The implicit algorithm for a viscoplastic constitutive is presented, this procedure is suitable for other viscoplastic constitutive relations. The strain rate effect, creep effect, stress relaxation effect and cyclic loading responses are tested using a single element model with different inelastic energy contributions; A titanium alloy plate specimen and a stainless-steel plate specimen under tension are studied compared with the experimental observations in existing literature. The results show that the above typical damage phenomenon and fracture process can be well reproduced; The inelastic energy significantly affects the force-displacement responses but has slight effect on the crack paths.

The paper describes an algorithm for semantic representation of behavioral contexts relative to a dichotomic decision alternative. The contexts are represented as quantum qubit states in two-dimensional Hilbert space visualized as points on the Bloch sphere. The azimuthal coordinate of this sphere functions as a one-dimensional semantic space in which the contexts are accommodated according to their subjective relevance to the considered uncertainty. The contexts are processed in triples defined by knowledge of a subject about a binary situational factor. The obtained triads of context representations function as stable cognitive structure at the same time allowing a subject to model probabilistically-variative behavior. The developed algorithm illustrates an approach for quantitative subjectively-semantic modeling of behavior based on conceptual and mathematical apparatus of quantum theory.

The expansion of concrete subjected to extreme elevated temperature is linked with intricate micro-structural variations, such as the transformation of the constituent phases. This study proposes a model to predict the thermal expansion of cement paste and concrete considering micro-structural changes under elevated temperatures ranging from 20°C to 800°C. The model presented can consider characteristics of various aggregates in the calculation of thermal expansion for concrete. The model is a combination of a multi-scale stoichiometric model and a multi-scale composite model. At the cement paste level, the model satisfactorily predicted a test result. At concrete level, upper bounds from the model were matched relatively well with test results by previous researcher. If the mechanical properties, such as elastic modulus (E), Poisson’s ratio (ν), and thermal deformation, of the aggregates used in concrete are given, it is likely that the model will reasonably predict experimental results.

In this article, we analyze the thermodynamics, thermal fluctuations and quasi-normal modes of a torus-like charge AdS black hole. The parameters of a torus-like charged AdS black hole are its mass, electric charge, and cosmological constant. We used a torus-like charge AdS black hole to evaluate thermodynamics through thermal fluctuations and found that it significantly affected the corrected thermodynamic potentials. Black holes of larger radii are more stable and significant. The effect of thermal fluctuation has been investigated on the other thermodynamic potentials such as the Hemohltz free energy, Gibbs free energy, enthalpy, and specific heat, using the concept of corrected entropy. Finally, we use null geodesics to deal with quasi-normal modes. The null geodesics provide the photon sphere angular velocity and Lyapunov exponent, which are the real and imaginary components of the quasi-normal modes in the eikonal limit. With inceasing charge and photon radius, angular velocity reaches its maximum, similar to Lyapunov's exponent.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

This article described the technology of determining earthquake epicenter with radar remote sensing on the example of Sentinel-1A/B. To determine the epicenter of the earthquake, the Earth's crust displacements were analyzed using radar remote sensing data obtained for the ascending and descending flight orbits. Coordinates of Earthquake epicenters were found according to line-of-sight displacement images via its maximum value. Displacement of the Earth's crust was obtained by processing in the GMTSAR package in the VirtualBox virtual machine of the Linux Ubuntu 16.04 operation system. Two earthquakes that occurred in 2020 were studied to determine the accuracy of finding epicenters using the ascending and descending orbits Sentinel-1A/B. These earthquakes occurred in Western Xizang, China, and Doganyol, Turkey. The maximum deviation from the officially registered epicenter coordinates was 15.38 km for Doganyol and 3.2 km for the Western Xizang earthquake. The negative displacement was 90 mm for Doganyol and 50 mm for Western Xizang.

This study provides a novel method to prepare metal-ceramic composites from magnetically selected iron ore using microwave heating. By introducing three different microwave susceptors (Activated Carbon, SiC, and a mixture of Activated Carbon and SiC) during the microwave process, effective control of the ratio of metallic and ceramic phases has been achieved easily. The effects of the three susceptors on the microstructure of the metal-ceramics and the related reaction mechanisms were also investigated in detail. The results show that the metal phase (Fe) and ceramic phase (Fe2SiO4, FeAl2O4) can be maintained, but the metal phase to ceramic phase changed significantly. In particular, the microstructures appeared as well-distributed nanosheet structures with diameters of ~400 nm and thicknesses of ~20 nm when SiC was used as the microwave susceptor.

Super-resolution technology is important not only in bio-related fields but also in nanotechnology, particularly in the semiconductor industry, where fine patterning is required and super-resolution is essential. However, observing microstructures beyond the diffraction limit proposed by Abbe and Rayleigh is considered impossible because of diffraction in traditional optical microscopy ob-servation techniques. However, in recent years, it has been possible to observe microstructures beyond the Rayleigh criterion by analysing the phase distribution of light. This study investigated the physical reasons why phase analysis makes this new analysis technique possible using simula-tions. The results confirmed that the phase component of the zero-order diffracted light reflected from the microstructure and able to pass through the lens system contained the phase information related to the shape of the measured object. Analysis of this information demonstrates the possi-bility of realising super-resolution based on speckle interferometry.

Crouch gait is a motor complication commonly associated with cerebral palsy, spastic diplegia, stroke, and motor-neurological pathologies, broadly defined as knee flexion in excess of 20° in the gait cycle. Uncorrected crouch gait results in fatigue, joint degradation, and loss of ambulation. Torsion springs have been used in cycling to store energy in knee flexion to reduce fatigue in the quadriceps during knee extension. SolidWorks was used to design a passive exoskeleton for the knee, incorporating torsion springs of stiffnesses 20,000 N/mm and 30,000 N/mm at the knee joint to correct four different crouch gaits. OpenSim was used to gather data from moments produced and knee angles from each crouch gait and the normal gait. Motion analysis of the exoskeleton was simulated using knee angles for each crouch gait and compared with moments produced with the normal gait moments in the stance phase of the gait cycle. All crouch gait moments were significantly reduced, and the correction of peak crouch moments was achieved corresponding to the normal gait cycle during the stance phase. These results offer significant potential for nonsurgical and less invasive options for wearable exoskeletons in crouch gait correction.

(1) Background: Myelodysplastic syndromes (MDS) are a group of diseases that affect the morphology and function of neutrophils. Rapid diagnosis of MDS is crucial for the initiation of treatment that can vastly improve disease outcome. (2) methods: In this work, we present a new approach for detecting morphological differences between neutrophils isolated from blood samples of high risk MDS patients and that for patients and blood bank donors (BBDs). First, using fluorescent flow cytometry CD66b positive cells were stained with 2′,7′-dichlorofluorescin diacetate (DCF) and Hoechst. Secondly, we imaged the cells using interferometric phase microscopy (IPM) without utilizing cell staining. (3) Results: flow cytometry results show MDS patients present different dispersion patterns compared to BBDs. BBDs present two distinct subpopulations (one of these are the H cells constituting 16% for neutrophils) whereas MDS patients present only 4% of this subpopulation. IPM results are consistent with this pattern: ~20% of BBDs neutrophils were characterized as H cells and whereas MDS patients present only ~4% of these cells. (5) Conclusion- IPM can be utilized for diagnosis of complex hematological pathologies such as MDS.

Co-doped SnO2 nanocrystals with tetragonal rutile-type (space group P42/mnm) structure have been investigated using in-situ high-pressure synchrotron angle dis-persive X-ray diffraction till 20.9 GPa at ambient temperature. The analysis of ex-perimental results based on Rietveld refinements suggest that rutile-type SnO2 un-dergoes a structural phase transition at 14.2 GPa to an orthorhombic CaCl2-type phase (space group Pnnm) with no coexistence during the phase transition. No further phase transition is observed till 20.9 GPa. The low-pressure and high-pressure phases are related via a group/subgroup relationship. However, as a discontinuous change in the unit-cell volume is detected at the phase transition, thus, the phase transition can be classified as first-order type. On decompression the transition is found to be re-versible. The results are compared with previous high-pressure studies on SnO2.

This research presents a comprehensive computational analysis of the two-phase flow dynamics within a three-dimensional porous transport layer (PTL) in a proton exchange membrane (PEM) electrolyzer. Employing advanced computational fluid dynamics (CFD) and a volume of fluid (VOF) approach, the study utilizes the finite-volume method to model a time-dependent, isothermal process within a laminar flow regime. Notably, the study treats oxygen as the dispersed phase and water as the continuous phase within the system. Investigations on the anode side uncovered the formation of gas bubbles on the electrode's surface subsequent to the electrochemical reaction. The simulation, spanning 5 seconds with 0.25-second intervals, highlights the critical role of the time interval between the initiation and 2 seconds in achieving pressure and velocity equilibrium within the PTL. The initial 0.75 seconds witnessed a peak in oxygen concentration, followed by its movement across the PTL, exhibiting a transition from regions of lower to higher concentration, consistent with known physical behaviour. Remarkably, the model recorded the highest pressure of 3.5 Pa at 0.25 s. Furthermore, the study observed an incremental pressure drop from 0.25 s to 0.5 s and 1 s, approximately amounting to 28.5% and 20%, respectively, ultimately leading to a uniform pressure distribution within the model. Over time, the pressure drop intensified across the entire model due to the evolving nature of the oxygen gas. These findings provide valuable insights into the complex dynamics of two-phase flow processes within PEM electrolyzers, contributing to the advancement of sustainable energy technologies.

New TLC-densitometric method have been developed for the identification and quantification of paracetamol (PA), propyphenazone (PP) and caffeine (C) of Saridon tablets using the NP-TLC technique combined with densitometry. This method allows for the simultaneous determination of PA, PP, and C in the same sample. Among all tested chromatographic conditions, the mixture consisting of chloroform + toluene + ethyl acetate + ethanol + acetic acid (18:18:7.5:5.0:0.3, v/v) and silica gel 60F254 plate proved to be the most effective for the separation of three tested active pharmaceutical ingredients (APIs) and substances related to paracetamol. The fully validation of the proposed NP-TLC method proves that it is specific, precise, accurate, robust and sensitive. The percentage content in relation to the content declared by the manufacturer is for propyphenazone 99.8%, paracetamol 101.6% and caffeine 100.8%, which are in accordance with pharmacopoeial requirements. The results presented indicate the possibility of using the developed method in the routine control of pharmaceutical preparations containing these APIs. The proposed method is economical and more sensitive compared to the previously proposed planar methods for the simultaneously determination of PA, PP and CAPIs. Will be an What is more, the presented method may be anaxcellent excellent economical alternative when HPLC method is unavailable for such determination.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

Corresponding to the principles of biological synapses, an essential prerequisite for hardware neural networks using electronics devices is continuous regulation of conductance. We implemented artificial synaptic characteristics in a (GeTe/Sb2Te3)16 iPCM with a superlattice structure under optimized identical pulse trains. Based on atomically controlling the Ge switch in the phase transition that appears in the GeTe/Sb2Te3 superlattice structure, multiple conductance states were implemented by applying the appropriate electrical pulses. Furthermore, we found that the bidirectional switching behavior of a (GeTe/Sb2Te3)16 iPCM can achieve a desired resistance level using the pulse width. Therefore, we also fabricated a Ge2Sb2Te5 PCM and designed a pulse scheme based on the phase transition mechanism to compare to the (GeTe/Sb2Te3)16 iPCM. We designed an identical pulse scheme that implements linear and symmetrical LTP and LTD based on the iPCM mechanism. As a result, the (GeTe/Sb2Te3)16 iPCM showed relatively excellent synaptic characteristics by implementing gradual conductance modulation, a nonlinearity value of 0.32, and LTP/LTD 40 conductance states using identical pulses trains. Our results demonstrate the general applicability of the artificial synaptic device for potential use in neuro-inspired computing and next generation non-volatile memory.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

The present work reports an experimental thermodynamic study of two nitrogen heterocyclic organic compounds, fenclorim and clopyralid, that have been used as herbicides. The sublimation vapor pressures of fenclorim (4,6-dichloro-2-phenylpyrimidine) and of clopyralid (3,6-dichloro-2-pyridinecarboxylic acid) were measured, at different temperatures, using a Knudsen mass-loss effusion technique. The vapor pressures of both crystalline and liquid (including supercooled liquid) phases of fenclorim were also determined using a static method based on capacitance diaphragm manometers. The experimental results enabled accurate determination of the standard molar enthalpies, entropies and Gibbs energies of sublimation for both compounds and of vaporization for fenclorim, allowing a phase diagram representation of the (p,T) results, in the neighborhood of the triple point of this compound. The temperatures and molar enthalpies of fusion of the two compounds studied were determined using differential scanning calorimetry. The standard isobaric molar heat capacities of the two crystalline compounds were determined at 298.15 K, using drop calorimetry. The gas phase thermodynamic properties of the two compounds were estimated through ab initio calculations, at the G3(MP2)//B3LYP level, and their thermodynamic stability was evaluated in the gaseous and crystalline phases, considering the calculated values of the standard Gibbs energies of formation, at 298.15 K.

Paraffin wax stores energy in the form of latent heat at a nearly constant temperature during melting and releases this energy during solidification. This effect is used in industrial energy storage. An unusual change in the shape of a melted droplet of paraffin wax placed on a relatively cold glass plate is studied. As the droplet solidifies, its upper surface becomes nearly flat and a dimple is formed in the center of this surface, making the droplet look like a fruit (pumpkins are more commonly shaped like this, but the authors prefer apples). A series of experiments, as well as physical and numerical modeling of the droplet's thermal state, taking into account the formation of a mushy zone between liquidus and solidus, made it possible to understand the role of gravity and gradual increase in viscosity and density of paraffin wax on changing the droplet shape and, in particular, to clarify the mechanism of formation of the dimple on its upper.

Purpose: To evaluate the efficacy and survival rates of same session ab interno trabeculectomy with the trabectome and Ahmed glaucoma valve implant (AT) in comparison to the Ahmed glaucoma valve alone (A). Method: A total of 107 eyes undergoing primary glaucoma surgery were enrolled in this retrospective comparative case series, including 48 eyes which underwent AT and 59 eyes which received A alone. Participants were identified using the procedural terminology codes, and their medical records were reviewed. The primary outcome measure was surgical success, defined as intraocular pressure (IOP) > 5 mmHg, ≤ 21 mmHg, and IOP reduction ≥ 20% from baseline at two consecutive visits after three months, no reoperation for glaucoma. Secondary outcome measures were IOP, the number of glaucoma medications, incidence of a hypertensive phase, and best corrected visual acuity (BCVA). Results: The cumulative probability of success at one year was 70% in AT, and 65% in A (p=0.85). IOP decreased significantly from 26.6 ± 10.1 mmHg at baseline to 14.7 ± 3.3 mmHg at the final follow-up in AT (p= 0.001). The corresponding numbers for A were 28.8 ± 10.2 and 16.7 ± 4.9, respectively (p= 0.001). The final IOP was significantly lower in AT (p= 0.022). The number of medications at baseline was comparable in both groups (2.6 ± 1.2 in AT and 2.5 ± 1.3 in A, p=0.851). Corresponding number at 1 year visit was 1.2±2 in AT and 2.8±1.8 in A (p=0.001). The incidence of a hypertensive phase was 18.7% in AT and 35.5% in A (p=0.05). HP resolved in only 30% of eyes. The criteria for HP resolution were fulfilled in 9 eyes (30%). There was no difference in the rate of resolution of the hypertensive phase between AT and A (33.3% and 28.5%, respectively, p=0.67). Conclusion: Ahmed glaucoma valve implant with same session trabectome surgery significantly decreased the rate of the hypertensive phase and postoperative IOP as well as the number of glaucoma medications.

This study provides an in-depth examination of the binary system of n-Nonadecane and 1-Octadecanol, representative of plant cuticular waxes. It emphasizes the crystallization and phase transitions in this hydrocarbon mixture. Using Differential Scanning Calorimetry (DSC) and Fourier Transform Infrared (FTIR) spectroscopy, the research uncovers detailed thermal properties and phase behaviors. The findings reveal the distinct phase transitions and enthalpy changes of each component in the binary system. This research is significant for its implications in under-standing the structural properties of plant waxes. Such insights are crucial for enhancing the effi-ciency of fertilizer and pesticide absorption in plant leaves, with broad applications in bionics and materials science. This study not only furthers the understanding of identifying specific phase transitions for each compound, facing challenges in detecting subtle changes using DSC. The re-search enhances understanding of plant cuticle waxes through FTIR analysis, revealing intricate molecular interactions and structural complexities. but also opens avenues for improved agri-cultural practices and material engineering, potentially influencing future innovations in these fields.

Memristors were proposed in the early ’70s of the XXth century by Leon Chua as a new electrical element linking the charge and the flux. Since that first introduction, these devices have positioned themselves to be considered as possibly fundamental for the new generations of electronic devices. It has to be mentioned that actual memristors have only been recognized to exist as physical elements. In this paper, we apply a modeling framework to generate a model describing experimental measurements performed on a ReRAM. We show how to apply the Dynamic Route Map technique in the general case to obtain an approximation to the differential equation that determines the behaviour of the device.

Nonlinear rheological properties of chiral crystal cholesteryl oleyl carbonate (COC) in blue phase III are investigated under different shear deformations; large amplitude oscillatory shear, step shear deformation, and continuous shear flow. Rheology of the liquid crystal is significantly affected by structural rearrangement of defects under shear flow. One of the examples on the defect-mediated rheology is the blue phase rheology. Blue phase is characterized by three dimensional network structure of the disclination lines. It has been numerically studied that the rheological behavior of the blue phase is dominated by destruction and creation of the disclination networks. In this study, we find that the nonlinear viscoelasticity of BPIII is characterized by the fracture of the disclination networks. Depending on the degree of the fracture, the nonlinear viscoelasticity is divided into two regimes; the weak nonlinear regime where the disclination network locally fractures but still show elastic response, and the strong nonlinear regime where the shear deformation breaks up the networks, which results in a loss of the elasticity. Continuous shear deformation reveals that a series of the fracture process delays with shear rate. The shear rate dependence suggests that force balance between the elastic force acting on the disclination lines and the viscous force determines the fracture behavior.

Because imbalanced power will cause the loss of the propulsion motor of the railway vehicle, and the increase in temperature will shorten the service life of the electric vehicle. Not only this, but also increase the cost of electricity and maintenance. In the past, the industry only focused on methods to improve power quality such as load capacity, relay setting, and harmonic resolution. Now, the consider of three-phase unbalance rate (TPUR) must be applied. I propose special transformers wiring (STW) to improve the three unbalance rates and provide different transformer wiring methods. According to the IEEE Committee, in the future, power companies will need to install balanced relay stations to improve three-phase unbalance rate. the internal regulations of Taipower must be less than 4.5% (voltage unbalance rate (NPSUR)of 2.5% and motor temperature rise of 12.5%). the derivation of the transformer "three-phase unbalance rate" model is the focus of the railway system. This research is based on the model derivation of different wiring methods to improve the hot problem caused by the three-phase imbalance and improve the service life of the train. And pointed out that Scott, Le-Blanc, Modified-Woodbridge three wiring methods can be applied to future railway system routes to improve the three-phase unbalance rate, in line with the IEEE standard of less than 2%.

Polymeric microparticles of polyethyleneglycol-polylactic acid-co-glycolic acid (PEG-PLGA) are widely used as drug carriers for a variety of applications due to their unique characteristics. Herein, we developed a novel method for the synthesis of uniformly sized microparticles via coaxial flow-phase separation. The study evaluated the effect of various process parameters on microparticle size and polydispersity including polymer concentration, stirring rate, surfactant concentration, and the organic/aqueous phase flow rate and volume ratio. The results demonstrated that stirring rate and polymer concentration had the most significant impact on the mean particle size and distribution whereas surfactant concentration had the most substantial impact on the morphology of particles. Several microparticle formulations yielding particle sizes in the range of (5-50 µm), morphology, and concentration were synthesized as a demonstration of the tunability and scalability of this method. Notably, by controlling the process parameters microparticles of less than ~ 7 μm could be made using polymer concentrations varying by an order of magnitude. Finally, we demonstrated the tunability and scalability of this method by showing a 10-fold increase in encapsulation efficiency, a 3-fold increase in drug loading of a model hydrophilic drug, and modified release kinetics in microparticle formulations of comparable sizes but different polymer concentrations.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. The doping-induced and concentration-dependent phase transition of zirconium dioxide under the influence of yttrium oxide was studied, after which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The calculations showed that ab initio research methods are capable of describing the mechanism of phase transitions of materials under the influence of alloying. That is, by optimizing the parameters of DFT calculations, it is possible to observe the effects of doping on other physical and chemical properties of materials, which are still beyond the scope of quantum chemical modeling. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

We report on the application of time-resolved inline digital holography to study the nonlinear optical properties of quantum dots deposited onto the sample glass. Fresnel diffraction patterns of the probe pulse due to noncollinear degenerate phase modulation induced by the femtosecond pump pulse were extracted from the set of inline digital holograms and analyzed. Absolute values of the nonlinear refractive index of both sample glass substrate and the deposited layer of quantum dots were evaluated using the proposed technique. To characterize the inhomogeneous distribution of samples’ nonlinear optical properties we proposed to plot an optical nonlinearity map calculated as a local standard deviation of diffraction patterns intensity induced by noncollinear degenerate phase modulation.

The silanol activity and trace metal detection methods for chemically bonded silica gels were evaluated in silico. Test compounds with large molecular sizes may demonstrate negative results because of the possibility of indirect hydrogen bonding via short alkyl groups or siloxane of the silica gels. This hypothesis was based on the observation of weak hydrogen bonding energy values similar to those observed in the study of the alkyl group effect on the hydrogen bonding of alkanols. Consequently, smaller molecules may be a better choice for the analysis of bonded-phase quality.

Effect of abrasive shape on the three-body abrasion behaviors of monocrystalline silicon was investigated by Molecular dynamics modelling. The axial ratio of abrasive particle was varied from 1.00, i.e., a complete sphere, to 0.40 to mimic abrasive shape. The particle’s movement turns toward sliding from rolling when the axial ratio becomes less than a critical value 0.46. In the abrasion process, the friction force and normal force showed an approximately sinusoid-like fluctuation for the rolling ellipsoidal particles, while the front cutting of particle caused that friction force increased and became larger than normal force for sliding particles. The phase transformation process was tracked under different particle’ movement patterns. The Si-II and Bct5 phase producing in loading process can partially transform to Si-III/Si-XII phase and backtrack to original crystal silicon under pressure release, which also occurred in the abrasion process. The secondary phase transformation showed difference for particles’ rolling and sliding movements after three-body abrasion. The rolling of particle induced the periodical and inhomogeneous deformation of substrates, while the sliding benefited producing high-quality surface in CMP process. This study aiming to construct more precise model to understand the wear mechanism benefits evaluating the MEMS wear and CMP process of crystal materials.

The EU has planned the phase-out of new vehicles based on internal combustion engines in favour of high efficiency electric cars by 2035 (Fit for 55 package). However, many doubts remain about the effectiveness of this choice for each Country of the Union in terms of CO2 emissions reduction, as each State is characterized by a different carbon intensity related to the production of electricity needed to manufacture and recharge vehicles. This study seeks to explore the Italian case. To this aim, carbon intensities related to the electricity production were calculated considering both the Italian electricity mix production at 2021 and those at 2035, envisaged considering two scenarios based on different introductions of renewable sources (RES). Afterwards, the values obtained were adopted for determining the CO2 emissions related to the whole production process of battery systems in Italy (emissions from mining and refining, scrap materials and final assembly included) by comparing some of the most up-to-date Life-Cycle Assessment (LCA) analysis related to the manufacturing cycle of the batteries. Finally, the results were adopted to calculate the starting carbon debit for A, B, C and M car segments for Mild Hybrid, Full Hybrid and Full Electric powertrains. At the same time, statistical road fuel/electricity consumption data were collected and overall CO2 emissions were calculated for the same vehicles for a defined mileage, so to determine break-even points with respect to the cumulative (i.e., from battery and road) carbon emissions. The results showed that advantages related to electric vehicles are significant only if a low carbon intensity related to electricity production is reached by means of a very high introduction of RES, thus keeping the door open for innovative powertrain technologies (plug-in), if fed with low carbon fuels.

The absorption of medium-chain fatty acids (MCFA) depends on the solubility of these components in the gastric fluid. Parameters such as the total MCFA concentration, carboxyl ionization level, and carbon chain length affect the solubility of these molecules. Moreover, the enzymatic lipolysis of solubilized triacylglycerol (TAG) molecules may depend on the carbon chain length of the fatty acids (FAs) components and their positions on the glycerol backbone. This present study aimed at investigating the effect of electrolyte usually formed during the gastric digestion phase on the solubility of MCFA, and evaluating the influence of the FA carbon chain length on the lipolysis rate during the in vitro digestion simulation. The results obtained here showed that the increasing of electrolyte concentrations tend to decrease the mutual solubility of systems composed by the caproic and caprylic fatty acids + sodium chloride, sodium bicarbonate, and potassium chloride solutions. We also observed that a conventional version of the thermodynamic UNIQUAC model was able to correlate the liquid-liquid phase behavior of the electrolyte solutions. Regarding the in vitro digestion simulation, the experimental data indicated that the action of the pancreatic enzyme occurred preferentially in TAG molecules comprised of short and medium-chain fatty acids.

Thermophysical characterization of three paraffin waxes (RT27, RT21 and RT35HC) is carried out in this study using DSC, TGA and transient plane source technics. Then, a numerical study of their melting in a rectangular enclosure is examined. The enthalpy-porosity approach is used to formulate this problem in order to understand the heat transfer mechanism during the melting process. The analysis of the solid-liquid interface shape, the temperature field shows that the conduction is the dominant heat transfer mode in the beginning of the melting process. It is followed by a transition regime and the natural convection becomes the dominant heat transfer mode. The effects of the Rayleigh number and the aspect ratio of the enclosure on the melting phenomenon are studied and it is found that the intensity of the natural convection increases as the Rayleigh number is higher and the aspect ratio is smaller. In the second part of the numerical study, a comparison of the performance of paraffins waxes during the melting process is conducted. Results reveals that from a kinetically RT21 is the most performant but in term of heat storage capacity, it was inferred that RT35HC is the most efficient PCM.

For decades SrTiO3 is in the focus of research with seemingly never-ending new insights regarding its ground state properties, its application potentials, its surface and interface properties, the superconducting state, the twin boundaries and domain functionalities, etc. Here, we focus on the already well-investigated lattice dynamics of STO and show that four different temperature regimes can be identified which dominate the elastic properties, the thermal conductivity and the birefringence. These regimes are the low-temperature quantum fluctuation dominated one, followed by an intermediate regime, the region of the structural phase transition at ~105 K and its vicinity, and at high temperatures a regime characterized by precursor and saturation effects. They can all be elucidated by lattice dynamical aspects. The relevant temperature dependences of the soft modes are discussed and their relationship to lattice polarizability is emphasized.

Dynamic phase modulation is vital for tunable focusing, beaming, polarization conversion and holography. However, it remains challenging to achieve full 360∘ dynamic phase modulation while maintaining high reflectance or transmittance based on metamaterials or metasurfaces in the terahertz regime. Here we propose a doubly resonant graphene-metal hybrid metasurface to address this challenge. Simulation results show that by varying the graphene Fermi energy, the proposed metasurface with two shifting resonances is capable to provide dynamic phase modulation covering a range of 361∘ while maintaining relatively high reflectance above 20% at 1.05 THz. Based on the phase profile design, dynamically tunable beam steering and focusing are numerically demonstrated. We expect this work will advance the engineering of graphene metasurfaces for the dynamic manipulation of terahertz waves.

In recent years, both domestic and international research on quadruped robots has advanced towards high dynamics and agility, with a focus on high-speed locomotion as a representative motion in high-dynamic activities. Quadruped animals like cheetahs exhibit high-speed running capabilities, attributed to the indispensable role played by their flexible spines during the flight phase motion. This paper establishes dynamic models of quadruped robots with different degrees of spine flexibility, providing a parameterized description of the flight phase motion for both rigid trunks and flexible spine quadruped robots. By setting different initial values for the spine joint and calculating the flight phase results for both types of robots at various initial velocities, the study compares and analyzes the impact of a flexible spine on the flight phase motion of quadruped robots. Through comparative experiments, the research aims to validate the influence of a flexible spine during the flight phase motion, providing insights into how spine flexibility affects the flight phase motion of quadruped robots.

Self-assembly membranes, composed of 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC) and 1,2-dihexanoyl-sn-glycero-3-phosphocholine (DHPC), were characterized at the total lipid concentration below 20 mM. The sizes of the assemblies varied depending on the molar ratio of DMPC and DHPC (q = [DMPC]/[DHPC]). The small assemblies with diameter of ca. 10 nm were formed at q ≤ 2.0 at 20 ºC (below phase transition temperature of DMPC). The physicochemical membrane properties were then studied using fluorescence probes, 1,6-diphenyl-1,3,5-hexatriene and 6-dodecanoyl-N,N-dimethyl-2-naphthylamine, upon the dilution. DHPC micelle showed a higher membrane fluidity, while the DMPC/DHPC membranes at q ≥ 0.5 showed lower membrane fluidities as well as DMPC vesicle in gel (ordered) phase. Upon dilution, the ordered membrane properties were maintained while the solution turbidities increased, implying the morphological change of the self-assembly, bicelle to the vesicle in gel phase. Based on the obtained results, a phase diagram of DMPC/DHPC binary system (at 20 ºC) is described: (i) the bicelle suspension is transparent and the membrane is in ordered state, (ii) the micelle suspension is transparent and the membrane is in disordered state, (iii) the vesicle suspension is turbid and the membrane is in ordered state.

Metasurfaces of gold (Au) nanoparticles on a SiO2-Si substrate were fabricated for the enhancement of second harmonic generation (SHG) using electron beam lithography and lift-off. Triangular Au nanoprisms which are non-centro-symmetric and support the second- order non-linearity were examined for SHG. The thickness of the SiO2 spacer is shown to be an efficient parameter to spectrally tune to maximise SHG. Electrical field enhancement at the fundamental wavelength was shown to define the intensity of the second harmonics. Numerical modeling of light enhancement was verified by experimental measurements of SHG and reflectivity spectra at the normal incidence. At the plasmonic resonance, SHG is enhanced up to ∼3.5×103 times for the optimised conditions.

This Article demonstrates how an eigendecomposition problem is inputted into a quantum circuit, how gates are applied in the quantum circuit, and how the output measurements are the correct eigenvalues. This process is known as quantum phase estimation (QPE). A quantum harmonic oscillator example, a foundational quantum physical chemistry problem, is demonstrated within the context of QPE. A particle in a box example, another quantum physical chemistry problem, may be solved by QPE with a caveat. These examples are of the limiting cases of diagonal matrices. Future advances in taking matrix inverses for solving linear sets of equations or finding ground state energies in the Schrödinger equation will use the principles implemented in this Article.

We present a numerical study in which large-scale bulk simulations of self-assembled DNA constructs have been carried out with a realistic coarse-grained model. The investigation aims at obtaining a precise, albeit numerically demanding, estimate of the free energy for such systems. We then, in turn, use these accurate results to validate a recently proposed theoretical approach that builds on a liquid-state theory, the Wertheim theory, to compute the phase diagram of all-DNA fluids. This hybrid theoretical/numerical approach, based on the lowest order virial expansion and a nearest-neighbor DNA model, can provide, in an undemanding way, a thermodynamic description of DNA associating fluids that is in semi-quantitative agreement with experiments. We show that the predictions of such scheme are as accurate as the ones obtained with more sophisticated methods. We also demonstrate the flexibility of the approach by incorporating non-trivial additional contributions that go beyond the nearest-neighbor model to compute the DNA hybridization free energy.

The study examined eating timing, diet, and the ratio of sleep phases in people with social jetlag (SJL). The study involved 83 participants who filled out a questionnaire, and 21 of them took part in the study of sleep phases by electroencephalography during the week. SJL was associated with a higher incidence rate of eating jetlag, eating phase delays, an increase in calorie intake after 9 p.m., a decrease in dietary fiber intake for breakfast, and melatonin-containing product consumption for dinner. Young people with SJL had a reduction in total sleep and light sleep phase duration by 60 and 36 min on work/school days and an increase in total sleep and REM sleep phase duration by 66 and 60 min on weekends, respectively. Young people consuming foods with more than 4234.5 ng of melatonin for dinner, compared with their peers consuming less than 313.2 ng of melatonin, showed a decrease in SJL and sleep debt by 54 and 90 min and an increase in the total sleep and the deep sleep phase duration by 66 and 30 min, respectively. Thus, the consumption of melatonin-containing foods for dinner is associated with a decrease in circadian misalignment and a sleep quality improvement.

Quantitative phase imaging by digital holographic microscopy (DHM) is a nondestructive and label-free technique, that has been playing an indispensable role in the field of science, technology, and biomedical imaging. The technique is competent for the imaging and analysis of label-free living cells and the investigation of reflective surfaces. Herein, we introduce a new configuration of a wide field-of-view single-shot common-path off-axis reflective DHM for the quantitative phase imaging of biological cells that leverages with several advantages including less-vibration sensitive to external perturbations due to common-path configuration, compact in size, simple in optical design, highly stable, and cost-effective. A detailed description of the proposed DHM system, including its optical design, working principle, and capability of phase imaging, is presented. The applications of the proposed system are demonstrated by quantitative phase imaging results obtained from the reflective surface (USAF resolution test target) as well as transparent samples (microlens array and living plant cells). The proposed system could find its applications in the investigations of several biological specimens and optical metrology of micro-surfaces.

The unsteady flow around the monopile under the influence of wave and vibration is studied by numerical method. Based on VOF model and SST Turbulence model, combined with Intermittent Transition model and dynamic mesh method, wave generation and pile vibration in numerical flume are simulated. The flow field around vibrating monopile in a calm water flume and a wave flume is simulated and the simulation results are compared. The calculation results show that the monopile vibration has a great disturbance to the unsteady flow around the pile, and the disturbance degree intensifies with the increase of the vibration amplitude of the monopile: Under the action of inertia, the vibration of the monopile leads to the reattachment of the shedding vortices; Under the influence of the reattachment vortices, the asymmetry of the vorticity on the side wall of the monopile intensifies; The intensification of the disturbance causes the reduction of the phase lead angle of the bed shear stress on the side of the single pile, and an additional high bed shear stress appears on the side of the monopile. In addition, the vortex structure formed alternately around the monopile during the vibration process leads to the periodic change of the high bed shear stress.

The Ni-Co-Cr-W-Mo system is critical for the design of nickel-based super-alloys. This system stabilizes different topologically close packed (TCP) phases in many of the commercially super-alloys with high W and Mo contents. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermodynamic calculations are applied to investigate the thermodynamics of the precipitates in two different W content Ni-Co-Cr-W-Mo super-alloys. Computational thermodynamics verified experimental observation of the f u phase formation as a function of temperature and alloy chemistry, but the kinetics for the precipitation of M6C phase do not agree with the experimental findings. The major precipitates of alloy 1 at temperatures 700 and 750 °C during long time exposure are M23C6, γ′ phase, and MC, and alloy 2 are M23C6, γ′ phase, MC, M6C and u phase. The W addition is found to promote the precipitation of M6C and u phase during exposure. The M6C has higher W and lower Ni content than that of u phase, meanwhile, M6C is an unstable phase would transform into M12C after 5000 h exposure at 750 °C. A great quantity of needle-like u phases precipitated after exposure at 750 °C for 5000h, which have no effect on the impact property of alloy 2.

In this study, the effect of heat treatment was investigated to influence the occurrence of fracture during manufacturing process of Alloy B steel with boron contents as high as 130 ppm. As the content of boron increases, it affects the phase transformation temperature and texture. The development of {111}<uvw> components in the γ-fiber is affected depending on the austenite fraction after phase transformation. The Alloy B steel indicated that the increase in the boron content increased the α to γ phase transformation temperature such that sufficient transformation did not occur in the normalizing condition. The cracks occurred at the point of the transition from elastic to plastic deformation in the ND direction during the rolling process, thereby resulting in failure. Therefore, it is necessary to avoid the intermediate heat treatment condition in which γ-fiber does not fully develop, i.e., an imperfect normalization.

The 8Nb isopleth section of a Ti-Al-Nb system is experimentally determined based on thermal analysis and thermodynamic calculation methods to obtain the phase transformation and equilibrium relations required for material design and fabrication. The phase transus and relations for the 8Nb-TiAl system show some deviations from the calculated thermodynamic results. The ordered βo phase transforms from the disordered β/α phases at 1200–1400 °C over a large Al concentration range, and this transformation is considered to be an intermediate type between the first- and second-order phase transitions. Moreover, the βo phases are retained at the ambient temperature in the 8Nb-TiAl microstructures. The ωo phase transforms from the highly ordered βo phase, rather than from α2 or βo with low degree of atom ordering B2 (LOB2) structure, with Al concentration of 32–43 at.% at approximately 850 °C. From the experimental detection, the transition of the ωo phase from the βo phase is considered to be a further ordering process.

Neuromorphic computing, reconfigurable optical metamaterials operational over a wide spectral range, holographic and nonvolatile displays of extremely high resolution, integrated smart photonics and many other applications need phase-change materials (PCMs) of the next generation with better energy efficiency, wider temperature and spectral range for reliable operation compared to current flagship PCMs as Ge2Sb2Te5 or doped Sb2Te. Gallium tellurides are promising candidates to achieve the necessary requirements because of higher melting and crystallization temperatures, combined with a low switching power and fast switching rate. At the same time, Ga2Te3 and non-stoichiometric alloys appear to be atypical PCMs, characterized by regular tetrahedral structure and the absence of metavalent bonding. The sp3 gallium hybridization in cubic and amorphous Ga2Te3 is also different from conventional p-bonding in flagship PCMs, raising a question of the phase-change mechanism. Besides, gallium tellurides exhibit a number of unexpected and highly unusual phenomena as nanotectonic compression or viscosity anomaly just above melting. Using high-energy X-ray diffraction, supported by first-principles simulations, we will unravel the atomic structure of amorphous Ga2Te5 PLD films, compare it with the crystal structure of tetragonal gallium pentatelluride, and investigate electrical, optical and thermal properties of these two materials to estimate their potential for memory applications as well as for other fields.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

The term deviation frequency denotes the boundary between the variable part of the amplitude and phase scintillation spectrum and the part of uninformative noises. We suggested the concept of the “characteristic deviation frequency” during the observation period which is defined as the most probable value of the deviation frequency under current local conditions. This work is a case study of the characteristic deviation frequency (fd) registered for GPS, GLONASS, Galileo and SBAS signals under quiet and weakly disturbed geomagnetic conditions in April 2021 at the mid-latitude GNSS station. Our results demonstrated that the fd value for all signal components of GPS, GLONASS and GALILEO signals varied within 15-22 Hz. The characteristic deviation frequency was 20 Hz for the mentioned GNSS signals. In difference, the deviation frequency was limited within 13-20 Hz for SBAS with the lower characteristic deviation frequency at 18 Hz. We assume that the concept of the characteristic deviation frequency can be used to determine the optimal sampling rate of the GNSS carrier phase data for the ionospheric studies. The characteristic deviation frequency can also characterize the state of the regular trans-ionospheric radio channel.

This study introduces a new procedure for three-component spectral matching of seismic ground acceleration records. The procedure involves preserving the phase angle and varying the Fourier amplitudes to match the spectra of the recorded records with a provided target spectrum that represents the spectral values of ground motions in three orthogonal directions. Several three-component recorded records were matched against two target response spectra to test the method. An accurate convergence was achieved in the velocity and displacement records. In addition, the scales among the components’ magnitude were maintained, creating realistic three-component ground motions. Such ground motion inputs are important to qualify critical structures sensitive to three-component motions. Our proposed procedure is novel because the present practices are mostly created based on one-component ground motions.

Based on the sensitive sum frequency generation cross-correlation frequency-resolved optical gating (SFG-XFROG) measurement setup, besides the pulse broadening, blue shift, red shift and obvious pulse acceleration, we observed the soliton evolution when the low energy soliton pulse with wavelength of 1555nm transmit through the Si photonic crystal waveguide. The measurements were nicely matched with the simulation results, which are achieved with an optimized nonlinear Schrödinger equation (NLSE) modeling. The effects of various parameters of the silicon photonic crystal waveguides and the incident pulses on the pulse transmission were also analyzed, including the nonlinear effects and dispersion such as the self-phase modulation (SPM), self-steepening (SS) and intra-pulse Raman scattering(IRS). The results help us understand further the ultra-fast nonlinear dynamics of soliton in silicon-based waveguides, and even open a novel way for soliton-based functional elements in CMOS-compatible platforms.

How does the human neurophysiological system self-organize to achieve optimal phase relationships among joints and limbs, such as in the composite rhythms of butterfly and front crawl swimming, drumming, or dancing? We conducted a systematic review of literature relating to CNS control of phase among joint/limbs in continuous rhythmic activities. SCOPUS and Web of Science were searched using keywords ‘Phase AND Rhythm AND Coordination’. This yielded 998 matches from which 23 papers were extracted for inclusion based on screening criteria. The empirical evidence arising from in-vivo, fictive, in-vitro, and modelling of neural control in humans, other species, and robots indicates that the control of movement is facilitated and simplified by innervating muscle synergies by way of spinal central pattern generators (CPGs). These typically behave like oscillators enabling stable repetition across cycles of movements. This approach provides a foundation to guide the design of empirical research in human swimming and other limb independent activities. For example, future research could be conducted to explore whether the two-layer CPG model proposed by Saltiel et al [1] to explain locomotion in cats might also explain the complex relationships among the cyclical motions in human swimming.

This study investigates the nonlinearities in three-phase inverters for SiC-based systems and compares their performance to IGBT-based systems. An analytical model of inverter voltage distortion is developed, which accounts not only for dead time (td), switching delay time, switching frequency (fs), and voltage drops of power devices, but also for output parasitic capacitance (Cout). Experimental tests validate the model, which provides a more accurate estimate of the inverter’s output phase voltage distortion. The power device characteristics are obtained from datasheets, while Cout is determined through experimentation. Three-phase inverters with varying switching frequencies, fundamental frequencies, and dead-time values are used in simulations and experiments to determine the influence of nonlinearity on phase voltage deviation and current distortion. The results show that, due to SiC devices’ faster switching time, the phase voltage deviation and phase current distortion are lower in SiC-based inverters than in IGBT-based ones for high-frequency applications, as the dead time can be reduced.

Among all the processing technologies of heat-treatable aluminum alloys like 2219 aluminum alloy, using friction stir welding (FSW) as the joining technology and using electromagnetic forming (EMF) for plastic forming technology both have obvious advantages and successful applications. Therefore, there is a broad prospect for the compound technologies which can be used on the 2219 aluminum alloy to manufacture the large-scale thin-wall parts in the astronautic industry. The microstructure and mechanical properties of 2219 aluminum alloy under the process compounded of FSW, heat treatment, and EMF were investigated by means of tensile test, optical microscope (OM), and scanning electron microscope (SEM). The results show that the reduction of strength, which was caused during the FSW process, can be recovered effectively by the post-welding heat treatment composed of solid solution and aging, while the ductility was still reduced after heat treatment. Under the compound technology of FSW, heat treatment, and EMF, the forming limit of 2219 aluminum alloy decreased distinctly due to the poor ductility of the welding joint. A ribbon-pattern, which was formed due to the banded structure caused by FSW process, was found on the fracture surface of welded 2219 aluminum alloy after EMF treatment. During the EMF process, because of the effects of induced eddy current, a unique structure, which was manifested as a molted-surface appearance under the SEM observation, was formed as the material fractured.

In recent years, the chiral biological effects of nanomedicines have become a subject of widespread interest. The research focus has been on understanding the influence of material chirality on cellular transcription and metabolism. Stress granules are membraneless organelles formed through liquid-liquid phase separation of G3BP1 proteins and related compartments. They have been extensively studied and proven to be closely associated with cellular damage repair and metabolism. However, the role and mechanism of chiral nanomaterials in modulating stress granules remain unknown. The aim of this study was to investigate the expression and structural characteristics of stress granules under the individual influence of chiral nanomaterials and in combination with chemotherapy. To achieve this, we constructed a library of chiral ligand-modified materials and employed immunofluorescence, live-cell imaging, and fluorescence recovery after photobleaching assays. We also used proximity labeling techniques combined with proteomics analysis to identify the protein corona adsorbed on the surface of the nanomaterials and explore their relationship with nanomaterial chirality. Our results demonstrate that the assembly of stress granules is chiral-dependent and can be regulated by chiral nanomaterials. Furthermore, we achieved enhanced chemotherapy sensitivity in cancer cells and protected normal cells by exploiting the chiral-dependent modulation of material assembly in stress granules. This study provides important insights into the regulation of membraneless cellular structures based on chiral biological effects.

The mechanism of vapor-gas deposition of vinyltrimethoxysilane (VS) and ethylene glycol (EG) from azeotropic solutions is investigated, which allows to reduce the evaporation temperature of the components of working mixtures. The need for such studies is associated with the development of a new direction in the technology of vapor-gas deposition of polymer coatings. Methods have been developed for monitoring the chemical composition of working solutions in evaporators using optical spectroscopy, which allow calculating the partial pressures of vapor phase components. Based on these studies, compositions of working solutions are proposed that allow to equalize the partial pressures of the components of working mixtures with a large difference in boiling point. A new method of vapor-gas deposition of non-volatile powder inhibitors on metals is proposed. Chemical compositions of siloxane coatings were determined using XPS and mechanisms of interaction of VS with polymerization promoters ethylene glycol and 1-hydroxy ethylidene-1,1-diphosphonic acid (HEDP) were proposed.

An experimental investigation on the heat pump performance improvement equipped with the two-phase ejector called “an ejector-expansion heat pump (EEHP)” is proposed. The system performance of the EEHP is compared with a vapour-compression heat pump (VCHP). The improvement potential is determined and discussed. The heat pump test system is constructed which is based on a water-to-water heat pump. It can be experimented with both EEHP and VCHP. The two-phase ejector with the cooling load up to 2500 W is installed for experiment. The results show that the EEHP always produces a higher heating rate and COP than the VCHP throughout the specified working conditions. The heating COP is increased by 5.7-12.2% depending on the working conditions. It is also that under the same heat sink and heat source temperature, the EEHP can produce lower compressor discharge temperature and lower compressor pressure ratio than the VCHP. This is evidence that the two-phase ejector can provide better compressor working characteristics which yields a longer compressor lifetime. It is demonstrated that a key to the performance of the EEHP is the expansion pressure ratio. A larger expansion pressure ratio yields a higher improvement potential when compared with the VCHP.

Aim: Aging is companied by deteriorations of insulin resistance (IR) and insulin secretion. However, little is known about the roles of aging on different phases of insulin secretion (ISEC); i.e., the first- and second-phase of insulin secretion (FPIS, SPIS) and glucose effectiveness (GE). Methods: Totally 169 individuals (43 men and 126 women) with the similar fasting plasma glucose (FPG: 90 mg/dL) and BMI (men: 23 kg/m2, women 22 kg/m2) were enrolled. IR, FPIS, SPIS, and GE were estimated using our previously developed equations shown below. Pearson correlation analysis was conducted to assess the correlations between age and four diabetes factors (DFs: IR, FPIS, SPIS and GE). The equations that are used to calculate the DF in the present study were built and published by our group. Results: The age of the participants ranged from 18- to 78-year-old. Men had higher FPIS but lower HDL-C levels than women (2.067±0.159, 1.950±0.186 μU/min and 1.130±0.306, 1.348±0.357 mmol/dl, accordingly). The results of Pearson correlation revealed that age was negatively related to IR and GE in both genders (IR: r = -0.39, p < 0.001 for men, r = -0.24, p < 0.003 for women; GE: r = 0.66, p < 0.001 for men, r = 0.78, p < 0.001 for women). In the meanwhile, FPIS was also only found to be negatively correlated with age in female (r = -0.238, p = 0.003). But there was no different with SPIS and age in both of genders. Conclusions: We have found that in Chinese with normal FPG level (90 mg/dl) and body mass index (men: 23 kg/m2, women: 22: kg/m2), age is negatively related to IR and GE in both genders. At the same time, only FPIS was found to be negatively related to age in women. The tightness of their relationships, from the highest to the lowest are, GE, FPIS and IR accordingly. The importance of GE should be re-evaluated. These results should be interpreted with caution because of the small sample size.

Quantitative differential phase contrast (qDPC) imaging has become an important method of optical measurement and life science research in microscopy because of its high reconstruction resolution and non-invasive, high-contrast and quantitative imaging of biological samples. Despite the continuous development of the principle and algorithm, the frame rate of the existing qDPC algorithm is still much lower than that of camera acquisition, so it is hardly applied to real-time image the fast-moving biological samples. In this paper, based on color-coded multiplexing strategy, a compact real-time quantitative phase imaging system is designed to realize multi-mode imaging. The system employs a programmable LED array to illuminate directly, and the phase reconstruction algorithm is deployed in the graphics processing unit (GPU) of the laptop to accelerate the calculation. The system can achieve high-speed quantitative phase imaging of non-stained biological samples, and the frame rate can reach 60fps. The device has the advantages of compact structure, low cost and portability. Thus, it is suitable for mobile medical applications.

The release profiles of methotrexate, an anticancer drug, from the monoolein liquid crystalline cubic phases were studied. The cubic phases were used either in the form of a lipidic film deposited onto a glassy carbon electrode surface or in the dispersed form of magnetocubosomes, which are considered a prospective hybrid drug delivery system. Commonly, cubosomes or liposomes are employed, but not in the case of toxic methotrexate, known to block receptors responsible for folate transport into the cells. The release profiles of the drug from the lipidic films were monitored electrochemically and described using the Higuchi model. They were also modified via changes in temperature; the release was faster, although deviating from the model when the temperature was increased. Magnetocubosomes - cubic phase nanoparticles containing hydrophobic magnetic nanoparticles placed in an alternating magnetic field of low frequency and amplitude, stimulated drug release from the suspension, which was monitored spectroscopically. These new biocompatible hybrid materials are very promising, allowing to control the release of the drug at the appropriate sites, but do require further investigations into their in vitro cytotoxicity and in vivo biodistribution.

Applying of blood biopolymers to regulate the phase composition is promising in designing the hydroxyapatite-based hybrid biomaterials with controllable resorbability. Hybrid materials based on hydroxyapatite and platelet-poor plasma (PPP) were formed in conditions of chemical precipi-tation at pH 11, [Ca2+] / [PO43–] ratio 1.67, PPP volume fraction of 6–24%, maturing time of 4–9 days. Mineral component of the materials was represented as 53% hydroxyapatite / 47% amor-phous calcium phosphate after 4 days of maturation, and 100% hydroxyapatite after 9 days of maturation. Varying PPP content from 6% to 24% provided forming of materials with rather de-fined content of amorphous calcium phosphate and biopolymer component, having desired mor-phology ranging from typical apatitic conglomerates to hybrid apatite-biopolymer fibers. Co-precipitated hybrid materials based on hydroxyapatite and PPP are promising for bone regen-eration in osteoplastic and maxillofacial applications.

Knowledge about the formation energies of compounds is essential to derive phase diagrams of multi-component phases with respect to elemental reservoirs. The determination of formation energies using common (semi-)local exchange-correlation approximations of density functional theory (DFT) exhibits well-known systematic errors if applied to oxide compounds containing transition metal elements. In this work, we generalize, reevaluate and discuss a set of approaches proposed and widely applied in the literature to correct for errors arising from the over-binding of the O2 molecule and from correlation effects of electrons in localized transition-metal orbitals. The DFT+U method is exemplarily applied to iron oxide compounds, and a procedure is presented to obtain U values, which lead to formation energies and electronic band gaps comparable to experimental values. Using such corrected formation energies, we derive the phase diagrams for LaFeO3, Li5FeO4 and NaFeO2, which are promising materials for energy conversion and storage devices. A scheme is presented to transform the variables of the phase diagrams from the chemical potentials of elemental phases to those of precursor compounds of a solid-state reaction, which represents the experimental synthesis process more appropriately. The discussed workflow of methods can directly be applied to other transition metal oxides.

The demands for high power and low emissions put focus on energy efficiency when developing new engines. An important part is the UAV engine cooling system, which cools the engine structure below damaging temperatures. For high temperatures in the cooling system there is a risk that boiling occurs and while the initial nucleate boiling enhances the cooling effect, the subsequent Film boiling decreases the heat transfer drastically. It is important to understand the benefits and limitations of various fluids when designing a two-phase cooling system. This paper proposes an alternative organic coolant. Its normal application range is 15°C to 400°C, and its pressure range is from atmospheric to 10.6 bar. DOWTHERM A fluid possesses unsurpassed thermal stability at temperatures of 400°C. This fluid, in both the liquid and vapor form, is noncorrosive toward common metals and alloys. Even at the high temperatures involved, the equipment usually exhibits excellent service life. Original equipment in many systems is still being used after 30 years of continuous service. The numerical results, described in this paper, show the potential of DOWTHERM A as a good alternative for cooling a UAV engine. It will extend the working temperature range of the Diesel engine and will maintain the structural integrity of the piston, cylinder and the piston rings.

Because of the large number of parameters that interact in their function, determining dynamic regime parameters as well as the mode of function of amplifying stages is an extremely complex problem. This paper describes a LabVIEW application for studying the functioning of an ampli-fier in various connections. The user selects the generator's parameters, the type of connection and its parameters, as well as the electric charge characteristics. The application can determine both the stage characteristics and the Bode characteristics. The amplifier's stability zone, as well as its gain and phase, are determined based on these characteristics. An important advantage of this application is that the design of the amplifier stage can be made starting from some param-eters that the amplifier can establish, from which the values of components can be determined. In order to validate the simulation results using the LabVIEW application, a specialized program Multisim was used, as well as experimental measurements using the Electronics Explorer Board. Both Multisim and Electronics Explorer Board can determine Bode characteristics. In both simu-lations and experimental amplifiers, the same schemes with the same transistor was used. The application can be used for educational purposes as well as to design the amplifier's stage to achieve specific parameters.

To overcome the two-phase flow instability of traditional boiling heat dissipation technologies, a porous wick was used for liquid-vapor isolation, thus realizing efficient and stable boiling heat dissipation. A pump-assisted capillary phase-change loop with methanol as working medium was established to study the effect of liquid-vapor pressure difference and heating power on its start-up and steady-state characteristics. The results indicated that the evaporator undergoes four heat transfer modes including flooded, partial flooded, thin film evaporation and overheating. The thin film evaporation mode was the most efficient one with the shortest start-up period. Besides, the heat transfer modes were determined by liquid-vapor pressure difference and power. The heat transfer coefficient could be significantly improved and the thermal resistance could be reduced by increasing liquid-vapor pressure difference as long as it did not exceed 8 kPa. However, when the liquid-vapor pressure difference exceeded 8kPa, its influence on the heat transfer coefficient weakened. In addition, a two-dimensional heat transfer mode distribution diagram considering both liquid-vapor pressure difference and power was drawn through a great number of experiments. During engineering application, the liquid-vapor pressure difference can be controlled to maintain efficient thin film evaporation in order to achieve the optimum heat dissipation effect.