The surface characterization of indium tin oxide (ITO) films was processed by oxygen (O2) plasma gas using a magnetron sputtering method of varying O2-plasma gas from 20 sccm to 100 sccm for potentially fostering in electronic devices applications on dye-sensitize solar cells (DSSC) in this work. In order to gain an outstanding performance rate with high-quality thin films, the affect of correlation between the electrical, optical, and morphology properties was significantly investigated. Clearly, the content of investigation exhibited that the films properties was changed by variation of the gas composition. These changes have contemporary relevance to the sputtering gas during the deposition process. To conclude, the greatest electrical properties was displayed by O2 -plasma gas flow rate of 20 sccm, which showed the lowest resistivity. In addition to this, the final products were practically fabricated to active layers for dye-sensitize solar cells (DSSC) applications. The highest efficiency of DSSC device was indicated of approximately 0.35% which was located by 40 sccm of the O2-plasma gas. Consequently, the study could be a possibility way of preparing ITO thin films with improved special properties of substantial applications for solar cells devices in the near future.

Hydrodynamic resistance is a critical parameter in microfluidics, affecting device functionality and performance. However, quantifying hydrodynamic resistance in microfluidics is a challenge due to many influencing factors and the difficulties associated with the precise measurements of low flow rates (< 10 L/min) and pressure drops (< 5 kPa). This article presents a simple experimental test method for assessing hydrodynamic resistance, correlating with theoretical and numerical calculations. The results demonstrate good agreement between benchtop and theoretical data, suggesting a potential standardized method for assessing hydrodynamic resistance in microfluidic devices.

Solifenacin (SFC) is a potent muscarinic antagonist that effectively reduces bladder muscle contraction, thereby alleviating symptoms such as frequency of micturition and urgency. Oxidation of SFC leads to the formation of impurities like Impurity K. Effective analysis and control of this impurity is crucial for ensuring compliance with regulatory standards and safeguarding patient health. To address these challenges, we propose a novel one-step synthesis of Impurity K from SFC. Impurity K was synthesized using cerium ammonium (IV) nitrate (CAN) in water/acetonitrile as the solvent. Additionally, we describe a new HPLC-MS method for the detection of Impurity K in solifenacin succinate tablets.

The rapid growth in scientific article publications allows us to access articles as soon as possible. Therefore, automatic summarization systems (ATSs) are widely preferred. In most studies, the en-tire source document is expected to be summarized, just as it would be summarized by a human. Summarizing long articles, such as scientific articles, is quite difficult due to token restraint and extraction of scientific words. To address this problem, a novel Graph-Based Abstractive Summa-rization (GBAS) model is proposed, which is a novel scientific text summarization model based on SciBERT and the graph transformer network (GTN). The document's integrity is maintained since the SciIE system uses the graph structure to create a terminology-based document structure. Therefore, long documents are also summarized. The proposed model is compared with baseline models and human evaluation. Human evaluation results show that the results of the proposed model are informative, fluent, and consistent with the ground-truth summary. The experimental results indicate that the proposed model outperforms baseline models with a 37.10 and 34.96 ROUGE-L score.

Solving the problem of searching for new scintillators based on available materials, we were the first to obtain and study a single crystal of CsI doped with divalent ytterbium ions. This work was directed to study of luminescence mechanism of Yb2+ ions and excitation transfer from crystalline matrix of CsI to dopant ions under VUV excitation. Using time-resolved spectroscopy, spin-allowed and spin-forbidden radiative transitions of ytterbium ions at room temperature were discovered. At 10 degrees, the emission of self-trapped excitons was detected. UV and VUV excitation spectra were obtained in the emission bands of ytterbium and self-trapped excitons. It was found that Yb2+ luminescence is excited in the excitonic region in the range of 10-45 eV. The mechanism of charge compensation of Yb2+ ions in a CsI crystal was also studied, the spectrum of the thermally stimulated depolarization current was measured, and the activation energies of the two observed peaks were calculated. These peaks belong to impurity-vacancy complexes in two different positions.It is concluded that Yb2+ ions are promising dopants for CsI scintillators and X-ray phosphors in combination with SiPM photodetectors.

Nowadays, Multi-needle electrospinning has used to be an efficient method for producing nanofiber membranes. But in the process, the fluctuation errors in electrospinning fluid flow rate have directly influence the membrane quality, which bringing instability and still have not been solved yet. For finding out the solution to the inaccurate flow control in multi-needle, it is necessary to develop a multi-stage flow runner spinneret for large-scale production of nanofiber membrane. At first, the paper uses the finite element software COMSOL to numerically simulate the polymer flow in the runner of spinneret. Based on it, the velocity field distribution curve was draw and the velocity instability coefficient of the polymer flow was attained, which are providing theoretical guidance for the optimal design of spinneret. Next, the response surface analysis method (RSM) was used to establish a regression model between the average diameter of the nanofiber membrane and the process parameters. Then, above regression model used to perform variance data processing between the average diameter and the process parameter configuration. After that, the 2D and 3D response surface profiles and the significance analysis were completed. Finally, the stability of the nanofibers production was improved, which attained the optimal adjustment of process configuration in multi-needle electrospinning.

This article introduces an innovative design method for public lighting systems that surpasses the limitations of conventional approaches, which rely on predefined lamp characteristics and spatial arrangement. By employing a multi-criteria decision algorithm, our study proposes an optimal design methodology considering several key aspects, including the distance between lamps, their type, power, and light distribution. The goal is to achieve optimal illumination that enhances visibility on public roads for drivers and pedestrians while simultaneously minimizing glare, installation costs and maximizing energy efficiency. The proposed methodology is implemented through an algorithm developed in Matlab, with results validated through simulations in Dialux. This information is used to construct a decision matrix, assessed using the CRITIC method across 180 different scenarios within a specific case study. The findings demonstrate the effectiveness of multi-criteria decision-making as a tool for significantly improving the planning and design of lighting in public illumination systems, allowing for selecting the optimal combination of parameters that ensure the best lighting conditions.

Ambulatory heart rate (HR) monitors that acquire electrocardiogram (ECG) or/and photoplethysmographm (PPG) signals from the torso, wrists, or ears are notably less accurate in tasks associated with high levels of movement compared to clinical measurements. However, reliable estimation of HR can be obtained through data fusion from different sensors. These methods are especially suitable for multimodal hearable devices, where heart rate can be tracked from different modalities, including electrical ECG, optical PPG, and sounds (heart tones). Combined information from different modalities can compensate for single source limitations. In this paper, we evaluate the possible application of data fusion methods in hearables. We assess data fusion for heart rate estimation from simultaneous in-ear ECG and in-ear PPG, recorded on eight subjects while performing 5-minute sitting and walking tasks. Our findings show that data fusion methods provide a similar level of mean absolute error as the best single-source heart rate estimation but with much lower intra-subject variability, especially during walking activities. We conclude that data fusion methods provide more robust HR estimation than a single cardiovascular signal. These methods can enhance the performance of wearable devices, especially multimodal hearables, in heart rate tracking during physical activity.

C-C motif chemokine receptor 1 (CCR1/CD191) is a member of G-protein-coupled receptors, and is expressed on myeloid cells, such as neutrophils and macrophages. Because the CCR1 signaling promotes tumor expansion in the tumor microenvironment (TME), the modification of TME is an effective strategy for cancer therapy. Although CCR1 is an attractive target for solid tumors and hematological malignancies, anti-CCR1 therapeutic agents have not been approved. Here, we established a novel anti-mouse CCR1 (mCCR1) monoclonal antibody (mAb), C₁Mab-6 (rat IgG_2b, kappa), using the Cell-Based Immunization and Screening (CIBS) method. Flow cytometry and Western blot analyses showed that C₁Mab-6 recognizes mCCR1 specifically. The dissociation constant of C₁Mab-6 for mCCR1-overexpressed Chinese hamster ovary-K1 was determined as 3.9×10^-9 M, indicating that C₁Mab-6 possesses a high affinity to mCCR1. These results suggest that C₁Mab-6 could be a useful tool for targeting CCR1 in preclinical mouse models.

The crosslinking behavior of polyethylene (PE) determines its exceptional performance and application. In this study, we investigated the crosslinking behaviors of different PE resins through model simulation and rheological methods. Specifically, the mathematical equation of "S" model was established for PE resin. According to this equation, the optimal maximum gel content for high-density polyethylene (HDPE) was found to be around 85%. Moreover, the maximum crosslinking degrees for different PE resins depended largely on their density and molecular weight. The melt viscosities before crosslinking in PE resins were highly influenced by their melt index. The higher melt indexes resulted in the lower storage moduli, improving melt processability during processing. In addition, the crosslinking rates of PE resins were strongly influenced by peroxide concentration, independent of PE resin structures. For high molecular weight and low-density PE resins, they exhibited decreased ti values, increased A0 values, and decreased k6 values. However, there were no noticeable variations in the values of k2 and phi among different PE resins. And all simulated modeling outcomes showed the remarkable consistency with the experimental rheological data. These findings are of utmost significance in the industrial manufacture of PE resin.

MoS2 lithium-based grease is suitable for lubrication protection between bearings at high temperatures and loads due to its excellent tribological properties. However, there is little research on the influence of different addition methods of MoS2 additive on the tribology and corrosion properties of lithium grease. In this work, vegetable oil with low toxicity, high biodegradation rate, and low cost was selected as the base oil, lithium 12-hydroxystearate as the thickener, and MoS2 as the additive. The effects of different adding modes of MoS2 on the tribology and corrosion properties of lithium grease were studied. The experimental results showed that adding 0.01wt% MoS2 before thickening was more conducive to improving the tribological properties of lithium grease. The average friction coefficient was 0.034, and the average spot diameter was reduced by 0.16mm. After grinding and adding 0.01wt% MoS2, the corrosion inhibition efficiency of the steel sheet was as high as 96.97%. The main reason was that the longer stirring and grinding were conducive to the uniform distribution of MoS2 in the grease, and the protective film formed by MoS2 and GCr15-bearing steel improved the lubrication performance and corrosion inhibition performance of the friction system.

Motivated by the intriguing discovery of $X(6900)$ by LHCb Collaboration, we undertake a comprehensive study of the $s\bar{s}s\bar{s}$ tetraquark system in positive parity, employing the Gaussian expansion within the chiral quark model method. We consider two structures, diquark-antidiquark ($ss$-$\bar{s}\bar{s}$) structure and meson-meson ($s\bar{s}$-$s\bar{s}$)strcuture, encompassing all conceivable color and spin configurations. Despite the absence of bound states in our calculations, we have identified potential resonant states with $J^P=0^{+}$, namely $R(0,2150)$ and $R(0,2915)$, as well as a resonant state with $J^P=1^{+}$ denoted as $R(1,2950)$, and a resonant state with $J^P=2^{+}$ denoted as $R(2,2850)$, utilizing the real-scaling method. Through a comparison of their energies and widths, we propose that $R(0,2915)$ and $R(1,2950)$ may share characteristics with $X(6900)$, while $R(0,2150)$ could be a promising experimental candidate for $f_0(2100)$. We strongly advocate for experimental investigations to shed light on the existence and properties of these resonant states.

Due to the inclusion of both the principles and divination methods, the study of Yijing (Yijing) becomes more complex. The complex data types, diverse semantic relationships, and unclear influencing mechanisms in Yijing pose challenges to its scientific research. Knowledge graph, as an advanced way of organizing knowledge, can provide technical support in exploring the hidden connections and knowledge structure within text resources. This paper proposes a method of constructing a Yijing knowledge graph based on Neo4j. By analyzing the concepts, entities, and various related relationships in Yijing, the method discusses the basic architecture, data model, and implementation steps of constructing the Yijing knowledge graph. It also extracts, integrates, and structures the Yijing knowledge, allowing for inquiries, associations, and reasoning about the knowledge and its various elements. By adopting a top-down approach, the paper reconstructs the fundamental knowledge system of the Yijing, including yin-yang, the five elements, generation and restriction, 64 hexagrams, and six lines(yao). It establishes a knowledge graph pattern layer and a data layer that encompass concepts, attributes, and relationships. With the technical support of the Neo4j platform, the visualization and retrieval of Yijing knowledge are realized, providing new ideas and methods for studying the mechanisms of the Yijing. The proposed method of constructing a Yijing knowledge graph can be expanded to other types of ancient scripture knowledge graph research and can be applied to the field of digital humanities, promoting in-depth cross-disciplinary research and integration.

In this paper, we aim to address the challenge of airflow interference during fault detection in high-speed train bogies by introducing a flow field and investigating the characteristics of the sound field distribution of critical components under its influence. This approach overcomes the limitation observed in previous studies that ignored the impact of the flow field. Furthermore, we evaluate and compare various layouts for inter-track acoustic sensor arrays. The proposed sensing methods hold significant practical engineering value, and the collected data serves as a valuable reference for acquiring acoustic signals from key bogie components in future research.

This paper presents a non-perturbative method for solving eigenproblems. This method applies to almost all potentials and provides non-perturbative approximations for any energy level. The method converts an eigenproblem into a perturbation problem, obtains perturbation solutions through standard perturbation theory, and then analytically continues the perturbative solution into a non-perturbative solution.

An estimation of the electric sources in the heart were conducted using a novel method, based on Huygens’ Principle, aiming at a direct estimation of equivalent bioelectric sources over the heart surface in real time. The main scope of this work was to establish a new, fast approach for the solution of the inverse electrocardiography problem. The study was based on recorded electrocardiograms (ECGs). Based on the Huygens’ principle, measurements obtained from a patient’s thorax surface were interpolated over the surface of the employed volume conductor model and considered as a secondary Huygens’ sources. These sources, being non-zero only over the surface under study, were employed to determine the weighting factors of the eigen-functions expansion describing the generated voltage distribution over the whole volume conductor volume. With the availability of the potential distribution stemming from measurements, the electromagnetics reciprocity theorem is applied once again to yield the equivalent sources over the pericardium. The methodology is self validated, since the surface potentials calculated from these equivalent sources are in very good agreement with ECG measurements. The ultimate aim of this effort is to create a tool providing the equivalent epicardial voltage or current sources in real time, i.e. during the ECG measurements with multiple electrodes.

We compared the performance of matrix-assisted laser desorption/ionization followed by a time of flight (MALDI-TOF) mass spectrometry and genomic DNA extraction followed by sequencing, assembly, and alignment for phylogenetic assessment (Genomics method). We collected the samples from four contaminated rivers in the Dominican Republic and analyzed MALDI-TOF efficacy and accuracy for identifying bacteria in the samples. We evaluated the results for both methods (MALDI-TOF and Genomics) and reported a similarity percentage between each method's results. The MALDI-TOF method had a 72.41\% of coincidence with the Genomics method. This could have been sequence contamination found in the Genomics method. When it was later filtered, the result's coincidence rate went up to 90\%.

Feature selection is a crucial step in machine learning, aiming to identify the most relevant features in high-dimensional data, in order to reduce the computational complexity of model development and improve its generalization performance. Ensemble feature ranking methods combine the results of several feature selection techniques to identify a subset of the most relevant features for a given task. In many cases, they produce a more comprehensive ranking of features than the individual methods used in them. This paper presents a novel approach to ensemble feature ranking, which uses a weighted average of the individual ranking scores calculated by the individual methods. The optimal weights are determined using a Taguchi-type design of experiments. The proposed methodology significantly improves classification performance on the CSE-CIC-IDS2018 dataset, particularly for attack types where traditional average-based feature ranking score combinations resulted in low classification metrics.

Hemorrhagic shock is the primary cause of death in patients with severe trauma, and the development of rapid and efficient hemostatic methods is of great significance in promoting the life-saving of trauma patients. In this study, polycaprolactone (PCL) nanofiber membrane was prepared by electrospinning technology. The PCL-PDA loading system was developed by modifying the surface of polydopamine (PDA) inspired by mussel adhesion protein, and the efficient and stable loading of thrombin (TB) was realized on the premise of ensuring the bioactivity of TB. The new thrombin loading system overcomes the disadvantages of harsh storage conditions, poor strength, easy to fall off, and can use thrombin to start rapid coagulation cascade reaction, which has the characteristics of fast hemostasis, good biocompatibility, high safety and wide range of hemostasis. The physicochemical properties and biocompatibility of PCL-PDA-TB membrane were verified by scanning electron microscopy, cell proliferation test, cell adhesion test and extract cytotoxicity test. Red blood cell adhesion, platelet adhesion, dynamic coagulation time and animal models all verified the coagulation effect of PCL-PD-TB membrane. Therefore, PCL-PDA-TB membrane has great potential in wound hemostasis.

Porous materials can be characterized by well-trained neural networks. In this study, fibrous paper-type gas diffusion layers were trained with artificial data created by a stochastic geometry model. The features of the data were calculated by means of transport simulations using the Lattice–Boltzmann method based on stochastic micro-structures. A convolutional neural network was developed that can predict the permeability and tortuosity of the material, through-plane and in-plane. The characteristics of real data, both uncompressed and compressed, were predicted. The data was represented by reconstructed images of different sizes and image resolutions. Image artifacts are also a source of potential errors in the prediction. The Kozeny–Carman trend was used to evaluate the prediction of permeability and tortuosity of compressed real data. Using this method, it was possible to decide if the predictions on compressed data were appropriate.

A novel phase-field method based numerical approach to modeling the compaction process of sedi- ments is presented. Water-logged rock or soil sediments are deposited on the water basins over time and the increasing volume of the sediment compacts under its own weight and external pressure. Coupled evolution of mass conservation, Darcy flow, and the viscoelastic constitutive response, in conjunction with the evolution of porosity and permeability, make this problem highly non-linear and involve moving boundaries. We adopt a phase-field approach to represent the moving sediment interface, and the underlying multiphasic model permits for studying compaction in dynamically evolving sediments. This approach does not necessitate a change of domain sizes as is the case of existing traditional models of sedimentation but rather treats sedimentation growth as a problem of interface motion. We first model a classical compaction problem in 1D to compare with existing results in the literature, and then extend the framework to 2D to model the compaction process taking place under the influence of gravity. The model is then extensively applied to understand the effect of the sediment initial state and the sediment material properties on the compaction process and its spatiotemporal evolution. Lastly, a strong validation of our phase-field treatment results against predictions from traditional methods of solving open boundary sediment compaction problems, and a good agreement between the conventional understanding and the numerical predictions of porosity dependence on the fluid pore pressure for various cases of geological interest, are used to demonstrate the applicability and scalability of this novel numerical framework to model more advanced sediment compaction problems and geometries.

In the context of the new crown epidemic, remote physical training will already be in order under the guidance of the Ministry of Education. There is a global focus on current lifestyle behaviors and the future health and well-being of youth. Youth physical activity, aerobic activity and muscle fitness levels are declining.[1] Research on the effects of youth physical training and group attitudes is still in its infancy. This study conducted in-depth interviews with online physical training students, parents, teachers involved in the construction of online physical training, and sports practitioners through interview methods, documentation, and mathematical statistics. The results of the interviews were qualitatively coded using NVivo to summarize the attitudes of different subjects toward physical fitness training and the influencing factors, (1) students were basically satisfied with the teaching effect of online physical fitness training (2) parents thought the teaching effect of online physical fitness training was average (3) physical education teachers thought the effect of online physical fitness training was average (4) physical education practitioners thought the effect of online teaching was poor.

A field experiment was conducted at farmer field of Sundarbazar, Lamjung during rainy season of 2020 with an objective to determine the dynamics of weed with respect different planting methods and varieties. The experiment was laid out in split plot design with three replications where five Varieties (KabreKodo 1, KabreKodo 2, Dalle 1, Okhale 1 and local) were used as the main plot factor and three planting methods (Direct sowing;10*10cm, Conventional transplanting;10*10 cm with 15 days old seedlings and System of Crop Intensification;25*25 cm with 30 days old seedlings) as sub plot factor. Result showed that among 5 genotypes of weeds based on Importance value index, Cyperusrotundus was the most dominant during the initial stage but after the first weeding, Aegeratumhaustinianum dominated the field. Weed biomass and density was recorded highest in directly sown field than that in transplanted field. Among the transplanted crop, weed infestation was seen higher in SCI than in conventionally transplanted finger millet due to wider spacing. But after the first hand weeding, due to profuse root growth and tillering in SCI, weeds were suppressed and thus weed biomass was observed higher in CT. After one hand weeding, SCI showed higher weed control index, crop resistance index and planting method efficiency index in terms of yield. Weed infestation was observed higher in Dalle 1 among varieties.

The novelty of this study consists in: i) synthesis and characterization of electrode materials recycled from a spent car battery and doped with MnO2 and CuO by the analysis of X-ray diffraction (XRD), Infrared (IR) and Electron Paramagnetic Resonance (EPR) data and ii) the investigation of electrochemical properties of prepared materials in view of new applications as electrode materials for battery. Electron Paramagnetic Resonance (EPR) data indicate that the intensity of the resonance line corresponding to the Cu+2 ion was modified with the increase of the dopant content. The analysis of X-ray Absorption Spectroscopy (XAS) data indicates that by increasing the dopant content there is a process of ordering the oxygen atoms around the lead similar to the PbO2 theoretical model. The electrochemical performances of the recycled and manganese-copper-doped materials are optimized for applications as new anodic electrode for the car battery.

Prospective end-users rated aptness, creativity, and innovativeness of biomimetic examples that featured different relationships to create combinations (e.g., used for) between nature and technology. Against common theorizing, similarity was not the most profound for creativity but rather appearance, being part_of, and property_of were. Creativity explained most of the variance in the level of innovation with aptness of the design in a strong supporting role. The focus of conceptualization shifted from ‘creation as new things coming from new ideas’ to ‘innovation as new ideas leading to new things.’ Results are interpreted in the Chinese context of utility. Both in education and industry, the use of 5*5 research grids with rating scales may work as a design method to develop and select functional variants during early design.

Trade of agricultural products has gained importance with the development of global trade. Cherries has a crucial place in Turkish agricultural exports. Fresh cherries are in the scope of this study. The aim of this study is to examine Turkey’s position and competitiveness in cherry trade. Trade Intensity Analysis Method which represents the course of trade flow among countries is used in the study. The study indicates that European countries which are Turkey’s tradition trade partner has a biggest trade share with Turkey and that share did not much change in years. By the way, Asia market especially China, became a game changer in cherry trade and Turkey should prepare itself for this situation.

Accurately monitoring insecticide resistance in target mosquito populations is important to combating malaria and other vector-borne diseases, and robust methods are key. The “WHO susceptibility bioassay” has been used for +60 years: mosquitoes of known physiological status are exposed to a discriminating concentration of insecticide. Several changes to the test procedures have been made historically which may seem minor but could impact bioassay results. The published test procedures and literature for this method were reviewed for methodological details. Areas where there was room for interpretation in the test procedures or where the test procedures were not being followed were assessed experimentally for impact on bioassay results: covering or uncovering of the tube end during exposure, number of mosquitoes per test unit, and mosquito age. Many publications do not cite the most recent test procedures, methodological details are reported which contradict the test procedures referenced or methodological details are not fully reported. As a result, the precise methodology is unclear. Experimental testing showed that using fewer than the recommended 15-30 mosquitoes per test unit significantly reduced mortality, covering the exposure tube had no effect, and using mosquitoes older than 2-5 days old increased mortality, particularly in the resistant strain. Recommendations are made for better reporting of experimental parameters.

Various efforts have been made to detect minimum value of glucose in any medium like water or body buffer solutions with high-sensitivity, accurate, and low-cost sensors in order to enhance life style. Therefore, the present study was done to investigate reliability of two-dimensional plasmonic structure by circular dichroism (CD) and ellipsometry tools in different concentrations of glucose. Our results confirmed a dependency of the CD signal on glucose concentrations and also a very good sensitivity based on the phase difference between each polarization in ellipsometry parameters with the help of an achiral plasmonic structure.

Air polution level measurement sometime needs tricky instrumentation, costly, and use chemical reagent that could bad impact to environment, it also time consuming for analysis. In other hand, air polution level measurement, include nitrogen dioxide (NO2) needs accuracy, rapid and environment friendly for its analysis and measurement. Differential Optical Absorption Spectroscopy (DOAS) develop as spectrum measurements both UV and visible, transmitted by specific canal using absorption Lambert Beer’s Law principal. On this basic method, NO2 measurement needs light source with 330 – 500 nm wavelength, it is possible to use cheap blue-LED for this measurement. This research intends to calibrate prototype instrumentation for measuring NO2 by DOAS based using Blue-LED (375 nm) passed in continual gas container. NO2 emission simulated in laboratory scale by reacting copper (Cu) with nitric acid (HNO3) result NO2 gas formation. Blue-LED spectrum analysed by compact CCD Spectrometer for its absorbance spectrum, then calibrated with NO2 measurement using USEPA Method 7B standard that is commonly used in testing laboratory as standard method for NO2 measurement. It has good corelation between spectrum absorbance in CCD Spectrometer to USEPA Method 7B with more than 95% linierity. As rapidity of this measurement and shown good accuracy, more development for this method could carry fast, accurate, cheap, also environmentally friendly method for NO2 measurement.

So called Higuchi’s method of fractal dimension estimation is widely used and the term Higuchi’s fractal dimension even occurs in many publications. This paper deals with this method from mathematical point of view. Terms distance and dimension and its basic properties are explained and Higuchi’s dimension according the original source is defined. Definition of Higuchi’s dimension was comparated with mathematical definition of the distance and dimension. It is showed, that the definition of the Higuchi’s dimension does not satisfy axioms of distance and dimension. So called Higuchi’s method and Higuchi’s dimension are mathematically incorrect. Therefore, all results achieved by this method are scientifically unreliable.

Surrogate model based optimization method is widely-used to accelerate the design and optimization process~\cite{marler2004survey}. The input of regression model used in the surrogate model are numbers, which requires users to parametrize the geometries. In this paper, a new parameterization-free surrogate model is introduced and its corresponding uncertainty quantification and sensitivity analysis method are discussed. The input of new surrogate model methods is surface mesh of simulation domain. \Gls{gnns} is used to extract geometric information, and \Gls{cnns} is used to predict contours. This framework bypasses parameterization,as a consequence, uncertainties introduced by manual parameterization is reduced. However, such changes compared with conventional surrogate model methods impose great challenge on uncertainties quantification and sensitivity analysis. Uncertainties quantification in this paper means the error bar of prediction results, which is calculated by Gaussian Process Regression method in current surrogate method. In this paper, a new quantification method achieved by Kullback-Leibler divergence (KLD) is introduced. And the sensitivity analysis is conducted by Automatic Differentiation, which gives a Jacobian matrix of inputs. The method and analysis mentioned above are demonstrated by a low-pressure steam turbine rotator and its exhaust system.

In this paper, we use three different experimental methods (particle method, grid method and hybrid method) to model and simulate the smoke from the perspective of fluid dynamics. Through the comparison of different methods, we conclude: The particle method can avoid the numerical dissipation problem caused by grid calculation, but it also brings problems such as the distortion of the trajectory of the example. The grid method is accurate in calculation, but it is prone to numerical dissipation and loss of details. Finally, we choose the hybrid method to store the vorticity in the form of particles in vortex particles, avoiding the numerical dissipation problem caused by the use of grids, and including rich turbulence, which perfectly shows the simulation effect of smoke.

Babies born prematurely are at risk of experiencing visual disturbances, hearing loss, disabilities, the risk of infection and even death. Care for premature babies requires serious attention for both health workers and parents. The role of parents is very important both during hospitalization and at home. Therefore, in order to improve the abilities of parents, it is necessary to make educational efforts with the right method.ObjectivesThis literature review aims to provide an overview of educational methods that nurses can use to improve the ability of parents to care for or care for the development of premature babies. The method used is to search for literature that fits the established theme using 5 data based, namely Scopus, ProQuest, Science Direct, Elsevier Clinicaly for Nursing and Web of Science. The strategy used in finding literature that fits the theme and is used in this literature review uses the PICOS framework. Then conducted a review with the PRISMA method. The literature selection results obtained 572 publications, after going through the selection obtained 11 literatures that match the theme, with 11 educational methods. These methods can be grouped into ideas, namely increasing parental involvement during treatment, using technology, stress management and continuous monitoring. The ability of parents to care for premature babies is needed in order to minimize complications in infants, reduce morbidity, avoid disabilities, increase growth and development of premature babies optimally and reduce parental stress levels, increase parental confidence and good parents' self-efficacy. Choosing the right educational method can improve the ability of parents to properly care for and provide developmental care for premature babies.

Multi-criteria decision-making (MCDM) methods and techniques have been applied to many real-world problems in different fields of engineering science and technology. The evaluation based on distance from average solution (EDAS) method is a new and efficient MCDM method. The aim of this study is to propose a modification to address two exceptional cases in which the EDAS method fails to solve an MCDM problem.

Biodiesel has caught the attention of many researchers because it has great potential to be sustainable fossil fuel substitute. Biodiesel has non-toxic and renewable nature and has been proven to emit less amount of environmentally harmful emissions such as hydrocarbons (HC), and carbon monoxide (CO), as well as smoke particles during combustion. Problems related to global warming caused by greenhouse gas (GHG) emissions could also be solved by utilizing biodiesel as a daily energy source. However, the expensive cost of biodiesel production, mainly because of the cost of natural feedstock, holds the potential of biodiesel commercialization. The selection of natural sources of biodiesel should be made with observations from economic, agricultural, and technical perspectives to obtain one feasible biodiesel with superior characteristics. This review paper presents a detailed overview of various natural sources, their physicochemical properties, as well as the performance, emission, and combustion characteristics of biodiesel when used in a diesel engine. The recent progress in studies about natural feedstocks and manufacturing methods used in biodiesel production were evaluated in detail. Finally, the findings of the present work reveal that transesterification is currently the most superior and commonly used biodiesel production method compared to other methods available.

BACKGROUND: To present a new method of urethral pressures examination, and to evaluate diagnostic capabilities of three dimensional profilometry , as an alternative to classical urethral profile (UPP) .Using four channel catheters and dedicated software global urethral pressures image is obtained. The method eliminates the main limitation of classical urethral profilometry where the catheter orientation determines the pressures picture limited to only one point in the uretral circumference while we observed even 50% differences in pressure measures depending on the point of measurement. METHODS: This is a preliminary study containing method presentation and analisys of the use in varied clinical cases of either healthy patients and patients with LUTS. The article includes technique and equipment decription, full evaluation of selected cases, including three dimensional urethral pressures distribution graphics. RESULTS AND CONCLUSIONS:Three dimensional profilometry compared to classical technique is comparable regarding the time, cost, technical difficulty and patient discomfort. At the same time we obtain much more data on the urethral pressures and its distribution.The results are easy for interpretation due to 3D movable graphics created automatically through the dedicated software.

The identification of the most rockfall-prone areas is the first step of the risk assessment procedure. In the case of land and urban planning, hazard and risk analyses involve large portions of territory and thus preliminary methods are preferred to define specific zones where more detailed computations are needed. To reach this goal, we developed the QGIS-based plugin QPROTO, able to quantitatively compute rockfall time-independent hazard over a three-dimensional topography on the basis of the Cone Method. This is obtained by combining kinetic energy, passing frequency and detachment propensity of each rockfall source. QPROTO requires the definition of few angles (i.e., the energy angle ϕ_p and the lateral angle α) that should take into account all the phenomena occurring during the complex block movement along the slope. The outputs of the plugin are a series of raster maps reporting the invasion zones and the quantification of both the susceptibility and the hazard. In this paper, we propose a method to relate these angles to some characteristics of the block (volume and shape) and the slope (inclination, forest density), to provide QPROTO users with a tool for estimating the input parameters. The results are validated on a series of case studies belonging to the North Western Italian Alps.

Rubbish in a forest environment is a great threat to this ecosystem, but this threat may also apply to the lost benefits for visitors to the forest. Previous studies proved that forest areas have a positive effect on obtaining psychological relaxation in the people visiting them. However, it was not known whether this restorative experience could be disturbed in any way by the presence of an open dump in the forest. To check how the presence of a landfill affects the visitors, an experiment was planned in which the respondents observed a forest area with a landfill and a forest landscape without a landfill for 15 minutes (control). The respondents then assessed the landscape using the semantic differential method and the Perceived Restorativeness Scale (PRS). An analysis of these observations showed that the presence of a landfill in the forest significantly changed the appreciation of the landscape by the respondents, the values of positive experiences decreased, and the negative experiences increased. Restorativeness was also reduced. Based on the results, it can be concluded that the presence of garbage in the forest may interrupt the restorative experience of its visitors.

In 2007, the excavation of the M-30 ring road located in Madrid and the creation of a green corridor either side of the Manzanares river brought significant change to the metropolitan area. The corridor and linear park which it provided were designed to contribute to the regeneration of the fluvial ecosystem, establish links among residents on each side of the river and promote cultural and leisure activities. This paper provides a sustainability analysis of the excavation of the M-30 (involving the socio-economic and environmental impact) 14 years after its construction. In order to show such an impact, an analysis of the area both prior to the project and after completion, as well as a hypothetical solution that uses improved materials, has been performed. This entails use of the multi-criteria decision-making model named MIVES (initials in Spanish, modelo integrado de valor para una evaluación sostenible). The MIVES method is based on the application of value functions of sustainability indicators selected by socio-economic and environmental criteria, chosen by experts. Results from analysis showed that the excavation of the M-30 considerably improved the sustainability of the area (sustainable index 3.43 and 6.26 both before and after the excavation works). However, use of improved materials in contrast with the application of conventional materials slightly improved the sustainability of the work (Sustainability Index 6.26 and 6.74, respectively, of the conventional materials).

Aim: Despite the endemic nature of contagious ecthyma in Nigeria, there is limited report on the molecular characterization of the isolates responsible for disease outbreaks. The aim of this study was to molecularly characterize ORFV isolated from clinical infections in goats in Sokoto metropolis. Materials and Methods: Seronegative embryonated chicken eggs were used to isolate ORFV via the chorio allantoic membrane (CAM) route according to the established protocol. Viral DNA was extracted from infected CAM and the full coding region of B2L gene was amplified by PCR and subsequently sequenced by Sanger’s method. The nucleotide sequence results were blasted for identification and phylogenetically analyzed using MEGA and Bioedit softwares. Results and Discussion: The results showed that B2L gene sequences of the ORFV UDUS/01/19/More strain showed slight variability (96- 98.7%) with the reference sequences. Our isolate clustered within the same clade with Korean strain signifying a close genetic relationship. Unique amino acid substitutions were noted in our isolate when compared with other references. This is arguably the first genetic characterisation of B2L gene of ORFV circulating in Nigeria. Conclusion: Our study has provided in sight into the genetic diversity of ORFV in the study area. This is crucial for the design of effective vaccines against the disease which are currently lacking in the country.

The market of ready-to-eat salads is experiencing a noticeable growth in Europe. Since they are intended to be consumed without additional treatments, these ready-to-eat products are associated with a high microbiological risk. The aim of this work was to evaluate the microbiological quality and safety of ready-to-eat salads sold in widespread supermarket chains in Lazio, Italy, at the packaging date, during shelf-life and during home-refrigeration. The study also aimed to determine the differences between low, medium, and high cost products. Salmonella spp., L. monocytogenes were chosen as safety indicators as specified by European regulations while total aerobic mesophilic bacteria and Escherichia coli were chosen as quality indicators as suggested by national guidelines. Analyses were performed following the ISO standards and in parallel, for the evaluation of total aerobic mesophilic bacteria, with an alternative colorimetric system, the Micro Biological Survey method, in order to propose a simple, affordable and accurate alternative for testing the microbiological quality of products, especially suitable for small and medium enterprises and on-site analyses. The study revealed high, unsatisfactory, total bacterial loads in all analyzed samples at the packaging date and expiring date and a very high prevalence of Salmonella spp. (67%) regardless of the selected varieties and cost-categories; L. monocytogenes was instead not recovered aligning with the results obtained in other studies.

This code provides computational facilities to simulate current versus time during the charging of Li-ion cells at desire constant voltage by considering multiscale physical phenomena. This code only considers a powder of active materials (at microscale or nanoscale) and a small part of electrolyte around it as a half cell. Then it is extended to a complete cell by applying correct boundary conditions. This code is very useful by modifying code parameters to understand the effect of the complex shape of active materials powder (surface area and powder size), kind of electrolyte, and the applied voltages on the charging response of Li-ion cell. As a summary, a microscale approach to the design of Li-ion cells has been provided via this code.

The market of ready-to-eat salads is experiencing a noticeable growth in Europe. The commercial success of these products is linked to the growing demand for fresh, healthy and nutritionally valuable products that can be consumed without preparation time and are perceived as safe and very high-quality products. Since they are intended to be consumed without additional treatments, these ready-to-eat products are associated with a high microbiological risk. The aim of this work was to evaluate the microbiological quality and safety of ready-to-eat salads sold in widespread supermarket chains in Lazio, Italy, at the packaging date, during shelf-life and during home-refrigeration. The study also aimed to determine the differences between low, medium and high cost products. Salmonella spp., L. monocytogenes were chosen as safety indicators as specified by European regulations while total aerobic mesophilic bacteria and Escherichia coli were chosen as quality indicators as suggested by national guidelines. Analyses were performed following the ISO standards and in parallel, for the evaluation of total aerobic mesophilic bacteria, with an alternative colorimetric system, the MBS method, in order to propose a simple, affordable and accurate alternative for testing the microbiological quality of products, especially suitable for small and medium enterprises and on-site analyses.

A common reactor type in the chemical and process industry is the fixed-bed reactor. Accurate modeling can be achieved with particle-resolved Computational Fluid Dynamic (CFD) simulations. However, the underlying bed morphology plays a paramount role. Synthetic bed-generation methods are much more flexible and faster than image-based approaches. In this study, we look critically at the two different bed generation methods: Discrete Element Method (DEM) (in the commercial software STAR-CCM+) and the rigid-body model (in the open-source software Blender). The two approaches are compared in terms of synthetically generated beds with experimental data of overall and radial porosity, particle orientation, as well as radial velocities. Both models show accurate agreement for the porosity. However, only Blender shows similar particle orientation than the experimental results. The main drawback of the DEM is the long calculation time and the shape approximation with composite particles.

Optical micro-angiography (OMAG) is a new method of detecting flow rate and widely used for in vivo imaging. Although OMAG can distinguish between flowing and stationary parts, it cannot obtain accurate flow rate information. This study proposed a range formula for OMAG and the ultrahigh-sensitivity OMAG (UHS-OMAG) method to quantify the measurement range of an entire system. The parameters of the angle between beam scanning and flow directions, the angular velocity of the galvanometer, and the offset of incident light were introduced, and a formula for calculating the range was derived. Experiments were conducted to measure fine and ultra-fine flow rates by using OMAG and UHS-OMAG methods. The minimum measured flow rate was approximately 30 μm/s, and the maximum measured flow rate was approximately 8 mm/s. Experimental results are in good agreement with the preset results.

Water is essential for living organisms. The increase in world population, global climate change and rapid growth in industrialization and urbanization have brought with them water issues around the world in recent years. Not only should existing water resources be used reasonably and efficiently but alternative water resources should also be explored and secured. Rainwater harvesting, which is one of the alternative water resources, can provide economic and environmental solutions. For rainwater harvesting, the size of reservoirs in which rainwater captured from roof catchments is stored should be determined. Determining the optimum tank capacity depending on precipitation and consumption rates allows us to make maximum use of rainwater tanks. The aim of this study is to determine the optimum tank capacity for the storage of rainwater captured from roof catchments in order to meet the water demand for agricultural production. Precipitation data were collected from the city of Isparta and its districts. Rainwater tank capacity was determined using the Rippl, residual mass curve, minimum flow and particle swarm optimization methods. Storage capacities varying according to roof areas and consumption rates are shown in a graph. Results show that particle swarm optimization is the best method.

Gold nanoparticles (AuNPs) are currently under intense investigation for biomedical and biotechnology applications, thanks to their ease in preparation, stability, biocompatibility, multiple surface functionalities and size-dependent optical properties. The most commonly used method for AuNPs synthesis in aqueous solution is the reduction of tetrachloroauric acid (HAuCl₄) with trisodium citrate. We observed variations in the pH and concentration of the gold colloidal suspension synthesized under standard conditions, verifying a reduction in the reaction yield by around 46% from pH 5.3 (2.4 nM) to pH 4.7 (1.29 nM). Citrate-capped AuNPs were characterized by UV-visible spectroscopy, TEM, EDS and zeta-potential measurements, revealing a linear correlation between pH and the concentration of the generated AuNPs. This result can be attributed to the adverse effect of protons both on citrate oxidation and on citrate adsorption onto the gold surface, which is required to form the stabilization layer. Overall, this study provides insight into the effect of the pH over the synthesis performance of the method, which would be of particular interest from the point of view of large-scale manufacturing processes.

The morphology and the activity of a submarine caldera, Avyssos, at the northern part of Nisyros volcano in the South Aegean Sea (Greece), has been studied by means of remotely operated underwater vehicle dives. The recorded time series of temperature and conductivity over the submarine volcano have been analyzed in terms of the Generalized Moments Method. The findings of the mathematical analysis shed light on the volcanic activity, but also on the morphology (shape) of the submarine volcano. The conductivity time series indicates the volcano is at rest in agreement with other types of observations. On the other hand, temperature fluctuations, which in general describe a multifractal process, show that the submarine caldera operates as an open system that interacts with its surroundings. This type of analysis can be used as an indicator for the state of activity and the morphological structure (closed or open system) of a submarine volcano.

Layered superconductors are attractive because some of them show high critical temperatures. While their crystal structures are similar, those compounds are composed of many elements. Compounds with many elements tend to be incongruent melting compounds, thus, their single crystals cannot be grown via the melt-solidification process. Hence, these single crystals have to be grown below the decomposition temperature, and then the flux method, a very powerful tool for the growth of these single crystals with incongruent melting compounds, is used. This review shows the flux method for single-crystal growth technique by self-flux, chloride-based flux, and HPHT (high-pressure and high-temperature) flux method for many-layered superconductors: high-T_c cuprate, Fe-based and BiS₂-based compounds.

Propionibacterium acnes and Staphylococcus epidermidis are the major skin bacteria that cause the formation of acne. The present study was conducted to investigate antibacterial activity of ethanolic extract of cinnamon bark, honey and their combination against acne bacteria. The antibacterial activity of extract of cinnamon bark and honey were investigated against P. acnes and S. epidermidis using disc diffusion method. Minimum Inhibitory Concentration (MIC) and minimal bactericidal concentration (MBC) were performed using Clinical and Laboratory Standard Institute (CLSI) methods. The interaction combination between extract of cinnamon bark and honey was determined by using a checkerboards method. The results showed that he MIC of extract of cinnamon bark and honey against P. acne were 256 µg/mL and 50% v/v, respectively, while against S. epidermidis were 1024 µg/mL and 50% v/v, respectively. The MBC of extract of cinnamon against P. acnes and S. epidermidis were more than 2048 µg/mL, whereas the MBC for honey against P. acnes and S. epidermidis were 100%. The combination of cinnamon bark extract and honey against against P. acnes and S. epidermidis, showed additive activity with the FICI value 0.625. Therefore, the combination of extract of cinnamon bark and honey has potential activity against acne causing bacteria.

This paper addresses the analysis for the nonlinear vibration response of a rectangular tube with a flexible end and non-rigid acoustic boundaries. This is a further work of the linear structural acoustic problem in a well-known acoustic book. In fact, the acoustic boundaries of an enclosed space sometimes are non-rigid and the structural vibration responses are nonlinear. These two points are the focuses of this paper. The multi-level residue harmonic balance method is applied to this nonlinear structural acoustic problem. The results obtained from the multi-level residue harmonic balance method and numerical method are generally in good agreement. The effects of excitation magnitude, tube length, and phase shift parameter etc. are examined.

A specific HPLC method has been developed and validated for the determination of vanillyl butyl ether in cosmetic products. The extraction procedure with an isopropanol water 1:1 mixture is described. The method uses a RP-C-18 column with isocratic elution and a UV detector. The mobile phase consists of a mixture of acetonitrile and buffer (Na2HPO4 20mM in water) (30:70 v/v) with a variable flow rate. The method was validated with respect to accuracy, precision (repeatability and reproducibility), specificity and linearity. The procedure described here is simple, selective and reliable for routine quality control analysis and stability tests of commercially available cosmetic products.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

In this paper, we focus on the impact of financial liberalization on stability of emerging stock market. We identify crises in a group of Latin American (Argentina, Brazil and Chile) and Asian countries (Philippines, Korea, Taiwan and Thailand) during 1975–2005. This paper aims to apply the methodology of CMAX method. Our results indicate that liberalization triggers more unstable stock market in the short run and generate several crises. Still, liberalization seems to generate more stable financial markets in the long run. Financial liberalization does not increase the frequency of crises in emerging countries and at long-term, crises are less several.

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

This paper presents a) the novel hybrid learning method to train the type-1 non-singleton interval type-3 (IT3) fuzzy logic systems (IT3 NSFLS-1) and b) the novel method named enhanced Wagner-Hagras (EWH) IT3 NSFLS-1 fuzzy systems which includes the level alpha 0 output to calculate the output y alpha using the average of the outputs y alpha k instead of their weighted average. The development of the proposed methodology uses the orthogonal least square (OLS) method to train the consequent parameters and the back propagation (BP) method to train the antecedent parameters. This proposal dynamically changes the parameters of only the level alpha 0 minimizing some criterion function as new information becomes available to each level alpha k. The antecedent sets are type-2 fuzzy sets, the consequent sets are fuzzy centroids, the inputs are type-1 non-singleton fuzzy numbers with uncertain standard deviations, and the secondary membership functions are modeled as two Gaussians with uncertain standard deviation and the same mean. Based on the firing set of the level alpha 0, the proposed methodology calculates each firing set of each level alpha k to dynamically construct and update the EWH IT3 NSFLS-1 (OLS-BP) system. The algorithm was tested in a hot strip mill facility to predict the transfer bar surface temperature showing its superior capability to obtain the industrial pyrometer’s knowledge uncertainty for tuning and its better performance when compared with IT2 SFLS, IT2 NSFLS-1, GT2 SFLS, GT2 NSFLS-1, IT3 SFLS, and IT3 NSFLS-1 trained with the BP-BP algorithm.

This article analyzes 6 probability distributions from the Generalized Pareto family, with 3, 4 and 5 parameters, with main purpose to identify other distributions from this family with applicability in flood frequency analysis compared to the distribution already used in the literature from this family such as Generalized Pareto Type II and Wakeby. This analysis is part of a larger and more complex research carried out in the Faculty of Hydrotechnics regarding the elaboration of a norm for flood frequency analysis using the linear moments method. In Romania, the standard method of parameter estimation is the method of ordinary moments, thus the transition from this method to the method of linear moments is desired. All the necessary elements for the distributions use are presented like, the probability density functions, the complementary cumulative distribution functions, the quantile functions, the exact and approximate relations for estimating parameters, for both methods of parameters estimation. All these elements are necessary for a proper transition between the two methods, especially since the use of the method of ordinary moments is done by choosing the skewness of the observed data depending on the origin of the maximum flows. A flood frequency analysis case study, using annual maximum and annual exceedance series, was carried out for the Prigor river, to numerically present the analyzed distributions. The performance of this distributions is evaluated using relative mean error, relative absolute error and linear moments diagram.

The emission of sulphur dioxide (SO2) from mining activities presents a substantial risk to public health, especially in populations located near mine industrial regions. This study investigated the potential correlation between exposure to sulphur dioxide (SO2) and its effects on respiratory health in Kankoyo Township, Zambia. A variety of methodologies were employed in this study, encompassing community participation, expert interviews, spatial analysis, and a retrospective examination of health and SO2 data for Kankoyo spanning 15 years. The results of our research indicated a worrisome correlation between the community and the presence of SO2, which has had a significant impact on their lives. The expert interviews also emphasized the effects of SO2, with respiratory cases accounting for approximately 75% of the reported cases. Additionally, the clinic officer observed that asthma cases have decreased following the implementation of a monitoring station in the community. Furthermore, overall emissions of SO2 have decreased since the upgrade of the smelter operation. A probable association was identified in the retrospective analysis between exposure to SO2 and the occurrence of asthma, respiratory non-pneumonia, and pneumonia infections. The findings of the retrospective research revealed a substantial association between SO2 concentrations and the susceptibility of individuals aged 5 years and older to asthma, respiratory non-pneumonia, and pneumonia infections. The results of the spatial study indicated that Kankoyo exhibited a significant level of SO2 pollution, above the established limitations set by the Zambian Environmental Management Agency (ZEMA) by an alarming margin of 1713%. In response to the challenges identified, this study proposed several measures. These measures encompassed the implementation of a requirement for regulators such as ZEMA and local communities to have access to real-time pollution data from mines, to enhance transparency. Additionally, the deployment of affordable air quality sensors, the resolution of medication shortages, the establishment of specialized respiratory health clinics, the initiation of IT-driven public awareness campaigns, and the expansion of research to investigate additional pollutants and confounding factors were also recommended.

Food insecurity is an economic and social condition involving limited or uncertain access to food. The problem of food insecurity in communities is influenced by economic conditions, food deserts, and barriers to accessing healthy food. Individuals experiencing food insecurity often endure concurrent problems of financial instability, hunger, and poor mental and physical health. Public and non-profit services in the U.S., such as the federally supported Supplemental Nutrition Assistance Program (SNAP) and community food banks, provide food-related assistance to individuals who are at a high risk of experiencing food insecurity. Unfortunately, many individuals who qualify for these services still experience food insecurity due to barriers preventing them from accessing food. Effective approaches for removing barriers that prevent individuals from accessing food are needed to mitigate the increased risk of chronic disease among vulnerable populations. This study tested a novel food insecurity intervention called FINDING-Food, which stands for Frequent Informational Nudges Directing Individuals to Needed Goods. Informational nudges in the intervention promoted food security through the elimination of information barriers to accessing food. The intervention used in this mixed-methods feasibility study consisted of informational nudges in the form of weekly text messages that were sent to food pantry clients experiencing food insecurity. The study aims were to test the efficacy and acceptability of the intervention by examining whether the informational nudges could enhance food pantry utilization, increase SNAP registration, and promote food security. Quantitative study results showed a lower prevalence of food insecurity in the intervention group than the control group at the end of the study. Qualitative findings revealed how the intervention group found the text messages to be helpful and informative. These study findings can enhance future food insecurity interventions aiming to eliminate barriers that prevent individuals who are food insecure from accessing healthy food.

There is a huge interest in developing novel hollow fiber (HF) membranes able to modulate neural differentiation to produce in vitro blood-brain barrier (BBB) models for biomedical and pharmaceutical research, due to the low cell-inductive properties of the polymer HFs used in current BBB models. In this work, poly(ε-caprolactone) (PCL) and composite PCL/graphene (PCL/G) HF membranes were prepared by phase inversion and were characterized in terms of mechanical, electrical, morphological, chemical, and mass transport properties. The presence of graphene in PCL/G membranes enlarged the pore size and the water flux and presented significantly higher electrical conductivity than PCL HFs. Biocompatibility assay showed that PCL/G HFs significantly increased C6 cells adhesion and differentiation towards astrocytes, may be attributed to their higher electrical conductivity in comparison to PCL HFs. On the other hand, PCL/G membranes produced a cytotoxic effect on the endothelial cell line HUVEC presumably related with a higher production of intracellular reactive oxygen species induced by the nanomaterial in this particular cell line. These results prove the potential of PCL HF membranes to grow endothelial cells and PCL/G HF membranes to differentiate astrocytes, the two characteristic cell types that could develop in vitro BBB models in future 3D co-culture systems.

In the present work we study the existence of solutions for hybrid nonlinear fractional integrodifferential equations. We developed an algorithm by using the operator theoretical techniques in order to obtain the approximate solutions. The main results depend on the Dhage iteration method that were incorporated with the modern hybrid fixed point theorems. The approximate solutions were obtained by using Lipschitz conditions and weaker form of mixed partial continuity. Further, we provide some examples to explain the hypotheses and the related results.

In this work, an algorithm for the scheduling of household appliances to reduce the energy cost and the peak-power consumption is proposed. The system architecture of a home energy management system (HEMS) is presented to operate the appliances. The dynamics of thermal and non-thermal appliances is represented into state-space model to formulate the scheduling task into a mixed-integer-linear-programming (MILP) optimization problem. Model predictive control (MPC) strategy is used to operate the appliances in real-time. The HEMS schedules the appliances in a dynamic manner without any a priori knowledge of the load-consumption pattern. At the same time, HEMS responds to the real-time electricity market and the external environmental conditions (solar radiation, ambient temperature etc). Simulation results exhibit the benefits of proposed HEMS by showing the reduction of up to 47% in electricity cost and up to 48% in peak power consumption.

A graphene-containing LDH was prepared by re-hydration of the oxides produced by the calcination of an organic LDH. While the memory effect is a widely recognized effect on oxides produced by inorganic LDHs, it is unprecedented from the calcination/re-hydration of organic ones. Different temperatures (400, 600 and 1100 °C) were tested, on the basis of thermogravimetric data. Water instead of a carbonate solution was used for the re-hydration, with CO₂ available from water itself and/or air to induce a slower process with an easier and better intercalation of the carbonaceous species within the layers. The samples were characterized by X-ray Powder Diffraction (XRPD), IR and Raman spectroscopy and scanning electron microscopy (SEM). XRPD indicate the presence of carbonate LDH mixed with a layered phase with a larger d-spacing. IR confirmed that the prevailing anion is carbonate, coming from the water used for the re-hydration and/or air. Raman data indicated the presence of low-ordered graphenic species moieties and SEM the absence of separated graphene of graphitic sheets, suggesting an intimate mixing of the carbonaceous phase with reconstructed LDH. Organic LDHs gave better memory effect after calcination at 400 °C. Conversely, the graphenic species are observed after rehydration of the sample calcined at 600 °C with a reduced memory effect, demonstrating the interference of the carbonaceous phase with LDH reconstruction and the bonding with LDH layers to form a graphene-LDH nanocomposite.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

The purpose of the research is to investigate the unique solvability of a nonlocal boundary value problem for a loaded equation of parabolic-hyperbolic type in a special domain. Methods: Using representations of a general regular solution, the existence and uniqueness of the problem posed is proved. Results: A new method for proving the unique solvability of nonlocal boundary value problems for one loaded equation of mixed type in a special domain has been formed and developed. Conclusions: The obtained results make it possible to solve some problems of genetics, immunology, transonic gas dynamics and thermal physics, which are associated with displacement.

Municipal Solid Waste Management (MSWM) struggles with significant policy and operational challenges, particularly concerning recyclables collection routes and fleet composition. Within the European Union, phasing out traditional fuel-based vocational vehicles, like garbage trucks, in favor of zero-emission alternatives is mandatory to achieve sustainable development objectives. Integrating electric solid waste collection vehicles into municipal fleets presents challenges due to differences in range, capacity, and noise levels. The emission is even more crucial in the systems where recyclables are collected separately, which requires a greater number of trips to be performed. This study addresses MSWM’s strategic aspect by minimizing the total cost of replacing waste collection vehicles while meeting emission constraints. The Fleet Transition Problem (FTP) was formulated and solved using a MARKAL-based approach. The objective of the FTP and a mixed integer linear program used to solve it is minimizing the overall cost of fleet modernization throughout a multi-phase planning horizon so that the sustainable transition of the fleet can be assured. Computational experiments affirmed the model’s effectiveness in strategizing fleet transition. This research outlines a multi-period model for transitioning to a zero-emission fleet and demonstrates the FTP’s potential for strategic decision-making. Notably, the study observes a consistent reduction in permissible emissions across the planning horizon.

This cross-country four-year longitudinal study investigated the development of processing speed throughout primary school education. The analyses were conducted on data collected from 441 schoolchildren in Grades 1, 2, 3 and 4 (aged 6.42 to 11.85 years) in the Kyrgyzstan and Russia. Mixed effects growth modeling was applied to estimate average and individual growth trajectories for processing speed at two cross-country samples. Latent class growth modeling was conducted to identify different types of growth trajectories for processing speed and to compare the distribution of the types within the analyzed samples. According to the results, processing speed significantly increases across primary school years. The trajectory is characterized by nonlinear changes with more intensive growth between Grades 1 and 2, which later slows down until Grade 4. There were no significant cross-country differences in the initial score of processing speed or developmental changes in processing speed across primary school years. The development of processing speed is described by a model with three quadratic growth types but minimally differs. It is concluded that in both samples, the development of processing speed may be characterized by homogeneity, with the most intensive growth from Grade 1 to Grade 2 and subsequent linear improvement until Grade 4.

Interdisciplinary research into the underlying neural processes of music therapy (MT) and subjective experiences of patients and therapists are largely lacking. The aim of the current study was to assess the feasibility of newly developed procedures (including EEG/ECG hyperscanning, synchronous audio-video monitoring, and qualitative interviews) to study the personal experiences and neuronal dynamics of moments of interest during MT with stroke survivors. The feasibility of our mobile set-up and procedures as well as their clinical implementation in a rehabilitation centre and an acute hospital ward were tested with four phase C patients. Protocols and interviews were used for the documentation and analysis of the feasibility. Recruiting patients for MT sessions was feasible, although data collection on three consecutive weeks was not always possible due to organisational constraints, especially in the hospital with acute ward routines. Research procedures were successfully implemented, and according to interviews, none of the patients reported any burden, tiredness or increased stress due to the research procedures, which lasted approx. 3 hours (ranging from 135min to 209min) for each patient. Implementing the research procedures in a rehabilitation unit with stroke patients was feasible and only small adaptations were made for further research.

Genomic selection (GS) can accelerate variety improvement when training set (TS) size, and its relationship with the breeding set (BS) are optimized for prediction accuracies (PA) of genomic prediction (GP) models. Sixteen GP algorithms were run on phenotypic best linear unbiased predictors (BLUPs) and estimators (BLUEs) of resistance to both fall armyworm (FAW) and maize weevil (MW) in a tropical maize panel. For MW resistance, 37% of the panel was the TS, and BS was the remainder whilst for FAW, random-based training sets (RBTS) and pedigree-based training sets (PBTS) were designed. PAs achieved with BLUPs varied from 0.66 to 0.82 for MW resistance traits, and, for FAW resistance, 0.694 to 0.714 for RBTS of 37%, and 0.843 to 0.844 for RBTS of 85%, and, these were at least two-fold those from BLUEs. For PBTS, FAW resistance PAs were generally higher than those for RBTS, except for one dataset. GP models generally showed similar PAs across individual traits whilst the TS designation was determinant since a positive correlation (R=0.92***) between TS size and PAs was observed for RBTS and, for the PBTS, it was negative (R=0.44**). This study pioneers the use of GS for maize resistance to insect pests in sub-Saharan Africa.

Graphene foam prepared by chemical vapor deposition method is a promising thermal interfacial material. However, the thermal properties of graphene foam highly depend on the experimental fabrication conditions during the chemical vapor deposition process. Aiming to reveal how to prepare the appropriate graphene foam for the various thermal management scenarios, the influence of experimental conditions on thermal properties of graphene foam is investigated. Furthermore, the contribution of thermal conductivity and thermal radiation to the effective thermal coefficient of graphene foam is carried out for comparison. Research results show that, the porosity and the cross-section shape of struts of growth template are two critical factors to affect the thermal transport of graphene foam, especially with the increase of temperature. In addition, the deposition time of graphene determines the wall thickness and affects the thermal conductivity directly. The thermal radiation contributes more than thermal conductivity when the temperature climbs continuously. Comparatively, the effective thermal coefficient of graphene foam composite with high porosity and circular shape struts is much superior to others at high temperature. The research findings can provide important guidance for the graphene foam fabrication and its applications in the field of thermal management.

A numerical method has been presented to simulate hypervelocity impacts into metal targets. The target is a rectangular prism and positioned at various inclined angles relative to the impact direc-tion, while four different projectile such as square prism, triangular prism, truncated cone and ogival shape are chosen. With this numerical model we aim to evaluate the risk of orbital debris impacting space structures in the design of shield systems for protection against hypervelocity impacts in space. To explore the geometric influences on hypervelocity impact, various projec-tile/target configurations are simulated using the Material Point Method. The Johnson–Cook plas-ticity model with a failure criterion is employed alongside Mie-Grüneisen's equation of state. Our analysis results reveal that the structure of debris cloud formations, scattering behavior of the ejected particle from both front and rear faces and penetration depth measures are significantly influenced by the projectile shape and impact angles.

Environmental chemicals, including PFAS (per- and polyfluoroalkyl substances), pesticides, industrial chemicals, and consumer products, commonly exist as mixtures. These substances are frequently exposed or co-exposed in varying concentrations, leading to potentially hazardous health effects such as cancer in humans. Thus, understanding the dose-dependent toxicity of chemical mixtures is important for assessing health risks. In this context, comprehensive methods for assessing the toxicity and identifying the mechanisms of harmful chemical mixtures are currently lacking. Here, the dose-dependent toxicity assessments of chemical mixtures are performed in three methodologically distinct phases. In the first phase, we evaluated our machine learning method (AI-HNN) and pathophysiology method (CPTM) for predicting toxicity. In the second phase, we integrated AI-HNN and CPTM to establish a comprehensive new approach method (NAM) framework called AI-CPTM, targeted at refining prediction accuracy and providing a comprehensive understanding of toxicity mechanisms. The third phase involved experimental validations of the AI-CPTM predictions. Initially, we developed binary, multiclass classification, and regression models to predict binary, categorical toxicity, and toxic potencies, using nearly a thousand experimental mixtures. This empirical dataset was expanded with virtual mixtures compensating the lack of experimental data and broadening the scope of the dataset. For comparison, we also developed additional machine learning models based on RF, Bagging, AdaBoost, SVR, GB, KR, DT, KN, and Consensus methods. The models achieved overall accuracies of over 80% with AUC values exceeding 90%. The regression models achieved an R2 >0.88. In the second phase, we innovatively integrated HNN-derived toxicity predictions with Z-scores from CPTM, resulting method called AI-CPTM. In the final phase, we demonstrated the superior performance of AI-CPTM through rigorous literature and statistical performance validations. Additionally, the predictive capability of AI-CPTM, including for PFAS mixtures and their interaction effects, was demonstrated by experimental validations using dose-response zebrafish embryo toxicity assays. Overall, the AI-CPTM approach significantly improves upon the limitations of standalone models and has shown extensive enrichments in the identification of toxic chemicals and mixtures. Further experimental studies involving human cell models, patient-derived xenografts, and investigations into the toxicity of multiple mixtures are currently underway.

The use of tuning forks to measure fluid density and viscosity is widely employed in fields such as food, medicine, textiles, automobiles, petrochemicals, and deep drilling. The explicit analytical model based on Euler-Bernoulli cantilever beam theory for the relationship between tuning fork resonance characteristics and the density and viscosity of fluid is only applicable to the situation where the fluid viscous effect is very small. In this paper, the finite element method is used to simulate the influence of large variations in fluid density and viscosity on the resonance characteristic parameters (resonant frequency and quality factor) of the tuning fork. The numerical simulation results are compared with the analytical analysis results and experimental measurement results. Then, the sensitivity of tuning fork resonance characteristic parameters to fluid density and viscosity is studied. The results show that compared with the analytical results, the numerical simulation results have a higher degree of agreement with the experimental measurement results. The relative difference in resonant frequency is less than 2%, and the relative difference in quality factor is less than 4%. This indicates that the finite element method includes the influence of fluid viscosity on tuning fork resonance parameters, which is more in line with the actual conditions than the analytical model. Simulating and analyzing the sensitivity of the tuning fork to fluid density and viscosity by the finite element method, it is possible to consider the situation where fluid density and viscosity vary over a large range. Compared with experimental measurements, this method has higher efficiency and can significantly save time and economic costs. This study can overcome the limitation of existing explicit analytical models, which are only applicable when the viscous effects of the fluid are very small. It enables a more accurate simulation of the coupling vibration between tuning forks and fluids, thereby providing theoretical references for further optimizing tuning fork structural parameters to enhance the accuracy of measuring fluid characteristic parameters.

The pathogenicity of grapevine geminivirus A (GGVA), a recently identified DNA virus, to grapevine plants remains largely unclear. Here, we report a new GGVA isolate (named GGVAQN) obtained from grapevine ‘Queen Nina’ plants with severe disease symptoms; the infectious clone of GGVAQN (pXT-GGVAQN) was also constructed. Infection assays indicated that Nicotiana benthamiana plants inoculated with GGVAQN display upward leaf curling and chlorotic mottling symptoms. Direct injection of Agrobacterium tumefaciens cells carrying pXT-GGVAQN into roots of in vitro-grown ‘Red Globe’ grape plantlets by syringe led to systemic infection with GGVAQN, and the plants exhibited chlorotic mottling symptoms on their upper leaves, and downward curling, interveinal yellowing, and leaf-margin necrosis symptoms on their lower leaves. Our results provide insights into the pathogenicity of GGVA, and a simple and efficient inoculation method to deliver infectious viral clones to woody perennial plants.

Formidable and often seemingly insurmountable conceptual, technical, and methodological challenges hamper the measurement of oxidative stress in humans. For instance, fraught and flawed methods, such as the thiobarbituric acid reactive substances assay kits for lipid peroxidation, rate-limit progress. To advance translational redox research, we present ten comprehensive “cheat codes” for measuring oxidative stress in humans. The cheat codes include analytical approaches to assess reactive oxygen species, antioxidants, biomarkers of oxidative damage and redox regulation. They provide essential conceptual, technical, and methodological information inclusive of curated “do” and “don’t” guidelines. Given the biochemical complexity of oxidative stress, we present a research question-grounded decision tree guide for selecting the most appropriate cheat code (s) to implement in a prospective human experiment. Worked examples demonstrate the benefits of the decision tree-based cheat code selection tool. The ten cheat codes define an invaluable resource for measuring oxidative stress in humans.

This work is aimed at investigating the capabilities and limits of the mid-fidelity numerical solver DUST for the evaluation of wind turbines aerodynamic performance. In particular, this study was conducted by analysing the benchmarks NREL- 5MW and Phase VI wind turbines, widely investigated in literature by from experimental and numerical activities. The work started by simulating simpler configuration of the NREL- 5MW turbine to progressively integrate complexities such as shaft tilt, cone effects and yawed inflow conditions, offering a detailed portrayal of their collective impact on turbine performance. A particular focus was then given to the evaluation of aerodynamic responses from the tower and nacelle, as well as aerodynamic behavior in yawed inflow condition, crucial for optimizing farm layouts. In the second phase, the work was focused on NREL Phase VI turbine due to the availability of experimental data on this benchmark case. Comparison of DUST simulations results with both experimental data and high-fidelity CFD tools shows the robustness and adaptability of this mid-fidelity solver for this applications, thus opening a new scenario for the use of such mid-fidelity tools for the preliminary design of novel wind turbines configurations or complex environments as wind farms, characterised by robust interactional aerodynamics.

An influenza A virus (H3N2) with an envelope with the same structure as COVID-19 was used for antiviral testing of material surfaces, in comparison with some results of feline calicivirus. The evaluation method used was the film adhesion method, in which the virus solution is placed on the material and adhered to it using a film. The evaluation method was based on the film adhesion method, in which the virus solution is placed on the material and adhered with a film, and the plaque method, in which the cell virus is allowed to infect the material and form plaques, but the appropriate virus concentration must be adjusted to observe the plaques. When not under that restriction, the plaques are often incomplete; this is observed. For this reason, this study applied an area measurement method that can reflect viral activity even when plaques are not obtained. This study revealed that different types of metallic materials have different antiviral properties. Specifically, the antiviral activity of iron, carbon steel, and nickel was relatively high, while that of stainless steel and titanium was relatively low. The order of antiviral activity was as follows: Fe, SS400, Ni, SUS316L, SUS304, and Ti.

This paper introduces the exponential time differencing (ETD) technique as a numerical method to solve efficiently American vulnerable options pricing. We address several challenges, including removing cross-derivative terms through appropriate transformations, treating early-exercise opportunities using the penalty method, and substituting fixed boundary conditions with corresponding one-sided finite differences. The proposed method is shown to be both accurate and efficient through numerical experiments, which also compare the results with existing methods and analyse the numerical stability and convergence rate.

In this work, we conducted a numerical study on the cavitation flow around a circular cylinder through the implementation of a porous coating. The primary objective addressed the effectiveness of utilizing a porous surface to control cavitation. We analyzed the cavitation dynamics around the cylinder and the hydrodynamic performance at different permeability levels of the porous surfaces. The flow was governed by the density based homogeneous mixture model and the volume penalization method was used to deal with the porous layer. A high-order accurate numerical method was adopted for the simulation of the cavitating flow through solving the preconditioned multiphase equations. The results revealed that the application of porous layer led to effective suppression of the cavitation vortex shedding. In addition, a reduction of the shedding frequency was obtained which accompanied by thinner and elongated vortices in the wake region of the cylinder. With the proper porous layer, the inception of the cavitation on the cylinder was suppressed and the amplitude of pressure pulsations due to the cavitation shedding mechanism was mitigated.

In this communication, we present a new simulated in situ lab/on-deck incubator, light spectrum replicator (LSR), and method to simulate the measured in situ HOCR light spectrum curves in incubation chambers. Carbon flux studies require detailed knowledge of primary and secondary production, including an understanding of temporal and spatial scales of variation. Interpretation of the processes involved during measurements continues to be difficult [1] since the incubation of the samples does not permit the study of rapid variations in carbon assimilation. Further, the significance of Dissolved Organic Matter of DOM in primary production is gaining attention as many autotrophic species are known for using organic substrates for growth, even in the dark [2–4] and since a significant portion of DOM can be accounted for from active release of intracellular metabolites by microbial consortia [5]. On the other hand, the major uncertainties in bacterial production measurements lie with the conversion factors used to calculate bacterial production (BP). For a given thymidine incorporation rate, estimates of BP can range by a factor of more than 20 [6,7]. Even though various new analytical tools have emerged [8], understanding of complex patterns of interactions within the microbial loop remains an open question.

Abstract: Circuit breakers are affected by multiple lightning strikes after the breaker has been tripped and can break down again, which will reduce the life of the circuit breaker and threaten the stable operation of the power system. Aiming at this problem, the paper obtained the temperature diffusion process of the inrush current process of circuit breaker opening and breaking through the schlieren technique, and combined with the existing image recognition technology to obtain the temperature characteristics of the airflow in the air gap of the contact, and the characteristics of the airflow flow. The results of the study show that the circuit breaker breakdown process generates a shock wave with a velocity approximately equal to the speed of sound under the same conditions. The maximum velocity of the airflow boundary diffusion is about 1/4 of the speed of sound under the same condition, and it decays very fast, reducing to the airflow drift velocity within 10ms after breakdown. The maximum temperature of the thermals is concentrated between 6000 and 8000 K and the temperature change is approximately inversely proportional to the square of time. The research provides the basis for the design of circuit breaker contact structure, opening speed optimization method, interrupter chamber and insulation design optimization.

Due to their contribution to human health, the production of healthy snacks has garnered the attention of both the scientific community and the food industry. This study was conducted to determine the suitability of frying and baking processing methods for producing green banana chips using two varieties: Barraganete and Dominico. The aim was to identify a treatment geared towards producing healthy snacks. Initially, the physicochemical properties of the raw materials were analyzed, revealing significant differences in starch, fat, fiber, and protein content. Subsequently, the bananas were processed into baked and fried chips. Multivariate statistical techniques such as ANCOVA, MANOVA, and post-hoc tests were applied to examine the influence of initial characteristics and detect variations attributable to the cooking method. The main findings showed that the initial protein level had a significant covariate effect on the final content in the chips. The Dominico variety generally proved more suitable for making baked chips, retaining higher percentages of protein, starch, fiber, and lower fat content than Barraganete. Baked chips showed significantly lower sodium and fat values than fried ones when differentiated by processing method. The "Dominico + Baked" treatment emerged as the superior alternative, with favourable levels of protein, starch, and low sodium and fat, positioning it as the most suitable for producing a healthy snack.

In this paper, we propose to explore a nonlinear fractional mathematical model of HFMD- Hand Foot Mouth Disease with vaccinated compartment. Firstly, we prove the non negativity and boundedness for the fractional order dynamical model. The system’s existence and uniqueness are studied using the formulation of the Caputo derivative operator. The fixed-point approach was used to get results indicating the presence of at least one solution. In numerical simulation, we obtained the approximate solution by using fractional Euler method.

Cirrus thinning, as one kind of geoengineering approach, not only cools our planet but also enhances the amount of sunlight reaching Earth's surface (brightening effect). This study delves into the brightening effect induced by cirrus thinning with a flexible seeding method. The thinning of only cirrus clouds results in a considerable globally averaged cooling effect (−2.46 W m−2), along with a notable globally averaged brightening effect (2.19 W m−2). Cirrus thinning also results in substantial reductions in the cloud radiative effects of the lower mixed-phase and liquid clouds. While these reductions counteract the cooling effect from cirrus clouds, they enhance the brightening effect from cirrus clouds. Consequently, the brightening effect caused by cirrus seeding (4.69 W m−2) is considerably more potent than its cooling effect (−1.21 W m−2). Furthermore, due to the more pronounced changes from the mixed-phase and liquid clouds at low- and mid-latitudes, the cooling effect is primarily concentrated at high latitudes. In contrast, the brightening effect is significantly stronger over most low- and mid-latitude regions. Overall, cirrus thinning could lead to a notable brightening effect, which can be leveraged to offset the dimming effect (the opposite of brightening effect) of other geoengineering approaches.

Underground storage of natural gas has the characteristics of clean and low-carbon, and has the ability to provide sustainable and stable supply. It is a very high-quality green energy that can increase the storage efficiency of gas storage through fracturing, achieving the sustainable development goal of "Carbon Peaking and Carbon Neutrality". The accurate evaluation of the fracability of a reservoir is an important prerequisite for reservoir fracturing design and post fracturing productivity evaluation. At present, research on fracability is mainly based on qualitative characterization or quantitative evaluation based on rock mechanics and fracturing construction parameters, which cannot fully reflect the rock composition and structure of each stage. Firstly, based on logging data, this paper analyzes the evolution laws of strain energy such as elastic properties, pre-peak dissipation energy, and post-peak fracture energy during the transition of rock materials from plastic deformation to brittle fracture in an energy perspective, and determines the key energy that affects the brittle characteristics of rocks. Secondly, a brittleness index evaluation approach has been established that can comprehensively reflect the mechanical properties of rocks during pre-peak deformation and post-peak damage stages. In addition, this article focuses on the impact of reservoir stratigraphic environment by combining the influence of geo-stresses with the rock brittleness index, and proposes a new method for evaluating reservoir fracability. Finally, this paper conducts a study on the fracability evaluation of three wells in a gas storage facility in eastern China. The results indicate that low modulus and fracability coefficient are beneficial for fracturing, thereby improving the gas production and peak shaving ability of gas storage.

Summary— Introduction: HIV (human immunodeficiency virus) is a virus that attacks and destroys one type of white blood cell, in particular, the CD4 lymphocytes, which are responsible for the body's immune response. This weakens the immune system to such an extent that it can no longer fight other viruses, bacteria, protozoa, fungi, and tumors. Methods: We investigated the potential biological role of the natural compound Polydatin (or piceid) using SwissDock, a web service to predict the molecular interactions that can occur between a target protein and a small molecule. Discussion: For the first time, we have investigated the role of polydatin against HIV-1 protease and HIV-2 protease through a computational approach by comparing their estimated ΔG values (kcal/mol) and the nature of the interactions between the residues in the catalytic center of the HIV proteases.Conclusion: From these simulations, Polydatin has excellent physical properties and an excellent estimated ΔG value (kcal/mol) of about -9.9 kcal/mol against HIV-2 protease and ΔG value (kcal/mol) of about -9.5 kcal/mol against HIV-1 protease. In addition, Polydatin was able to bind to two key amino acids of the catalytic triad sequence common to asparagine proteases (Asp25 and Gly27)

In this study, the autofrettage method, which is used to increase the durability of cylindrical parts, was applied to a barrel made of steel material according to the AISI 4340 standard. Assuming that the barrel works continuously under the pressure of 400 MPa, optimum autofrettage was performed. The stresses occurring on the barrel before and after autofretage were calculated. Additionally, analytical equivalent stress values (Von-Mises) formed on the part's wall were compared with numerical analysis results obtained with a commercial finite element program ANSYS®, and their compatibility was examined. As a result of the calculations and analysis performed, it was observed that autofretage has positive effect on increasing the pressure carrying capacity of the barrel. After autofrettage the cylindrical part, it was determined that the Von-Mises stress values formed in the part wall changed and these stresses took the lowest value at a point (elastic-plastic interface). It has been evaluated that this point gives the optimal autofretage pressure value for a certain operating pressure. After the autofrettage application, it was determined that the Von-Mises Stress value in the barrel wall decreased by 25.27 % and the pressure carrying capacity of the barrel increased without any design or dimensional change. It has been seen that the analytical and numerical analysis results are consistent with each other, and it is expected that this study will guide and contribute to the studies to be conducted on increasing the strength or lightening the weight of the parts.

Compton cameras detect scattered gamma rays and estimate the distribution of gamma-ray sources. Nonetheless, crafting a camera tailored to a specific application presents formidable challenges, often necessitating the implementation of diverse image reconstruction techniques. Delving into the factors influencing these cameras can pave the way for design optimization and performance enhancement. This study introduces an inventive detector design for Compton imaging systems, building upon the achievements of prior designs. The proposed system contains eight scatterer detectors and a semiconductor absorber detector, spaced at 1 mm and 30 mm intervals, respectively. The source-to-first-scatterer-detector distance is 5 mm, with scatterer and absorber detector plates measuring 70× 70× 2.125 mm³ and 70× 70× 10 mm³, respectively. Geant4 simulation toolkit models the Compton imaging system, and an analytical method reconstructs Compton camera images. Unlike more straightforward techniques, the analytical method directly reconstructs Compton camera images by solving the equation relating to the reflected image data. This approach is implemented in the C++ programming language. The study's findings reveal that the analytical method discerns optimal conditions and parameters that significantly influence efficiency, yielding a full width at half maximum (FWHM) of 3.7 mm with an angular uncertainty of approximately 2.7 degrees at an energy level of 0.662 MeV. Compared to another experimental design employing the analytical image reconstruction approach, the FWHM value decreased by 0.7 mm. This study presents an innovative detector design and an analytical reconstruction method for Compton imaging systems, showcasing improved efficiency and accuracy.

Quantum computing is an emerging field that have given a significant impact on optimization. Among the diverse quantum algorithm, the quantum gradient descent has become a prominent technique for solving unconstrained optimization problems. In this paper, we propose a quantum-spectral Polak-Ribi{\'e}re-Polyak (PRP) conjugate gradient approach. The technique is considered as a generalization of the spectral PRP method which employs a $q$-gradient that approximate the classical gradient with quadratically better dependence on the quantum variable $q$. Additionally, the proposed method reduces to the classical variant as quantum variable $q$ gets closer to $1$. The quantum search direction always satisfies the sufficient descent condition and does not depend on any line search. This approach is globally convergent with the standard Wolfe line search without any convexity assumption. Numerical experiments are conducted and compared with the existing approach to demonstrate the improvement of the proposed strategy.

In order to examine the impact of geometric configuration of the human vocal tract on the redistribution of acoustic energy in the frequency spectrum, it is necessary to assemble computation models, which facilitate simple modification of the model’s geometric characteristics. This article describes how the human vocal tract model was constructed using so-called super-elements using the improved reduced system method. The mentioned procedure allows using such a model for demanding optimization calculations, for which the model is modified on the super-element level. Furthermore, the article presents an alternative approach, in which an isoparametric element of a higher degree polynomial was derived. Both approaches were compared and used to find the geometric configuration of the human vocal tract amplifying acoustic energy values on the frequency spectrum to around 3kHz.

The vibration response of soil is a key property in the field of agricultural soil tillage. Vibration components of tillage machinery are generally used to reduce tillage resistance and improve work efficiency, the pressure variation under low-frequency vibration will affect the fragmentation and dispersion of farmland soil. However, the gradient of pressure variation, frequency domain response, and effective transmission range are unclear. A new method based on DEM (Discrete Element Method) is presented to study the vibration response and pressure transmission under low-frequency vibration. Bench test results showed that peak pressure positively correlates with the vibration frequency and attenuates rapidly at the vibration distance of 100 to 250 mm. The results data were also selected to determine the simulation model parameters. Amplitude, vibration frequency, and soil depth were used as test factors in single-factor simulation tests, and their effects on the peak pressure, frequency domain response, and effective transmission distance were analyzed. The results showed a positive relationship between the peak pressure and the test factors. The peak pressure increases with a maximum gradient of 19.02 kPa/mm at a vibration distance of 50 mm. The amplitude, vibration frequency, and soil depth positively correlate with the dominant frequency amplitude. The main frequency is independent of amplitude and soil depth. At the vibration distance of 250 mm, the dominant frequency is approximately twice the vibration frequency at 7–11 Hz and approximately equal to the vibration frequency at 13–15 Hz. Multiple exponential functions were used to fit the peak pressure attenuation function, obtaining an effective transmission distance range of 347.15 to 550.37 mm for the 5kPa cut-off pressure. For a soil depth of 300 mm, the vertical shear wave diffusion angle is greater than the horizontal shear wave diffusion angle. The study clarifies the vibration response of soil under low-frequency vibration, which helps to design vibration type soil-engaging components of tillage machinery and match vibration parameters for energy saving and resistance reduction in soil tillage.

The diverse physical appearances and wide density range of polymer bead foams offer immense potential across various applications and future advancements. The multi-scale and multi-level structural features of bead foams involve many fundamental scientific topics. This review presents a comprehensive overview of recent progress in bead foams preparation and molding techniques. Initially, a comparative analysis is conducted among bead foam characteristics of distinct polymers, based on their unique properties. Subsequently, a summary and comparison of molding processes employed for fabricating bead foam parts are provided. Beyond traditional methods like steam-chest molding (SCM) and adhesive-assisted molding (AAM), emerging techniques like in-mold foaming and molding (IMFM) and microwave selective sintering (MSS) are highlighted. Lastly, the bonding mechanisms behind the diverse molding methods are discussed.

In an era characterized by the ever-shifting landscapes of the digital realm, this paper intricately examines the interplay between digital culture, cultural dynamics, and beliefs in academia. Utilizing insights from cutting-edge language models, the study uncovers nuanced cultural expressions among Arts and Sciences students navigating the digital domain. Employing qualitative methods including interviews, observations, in-depth literature reviews, and thematic analysis, findings highlight digital interactions' transformative impact on cultural narratives and the potential of digital ethnography as a lens for understanding intricate cultural phenomena. This research enriches digital ethnography and cultural dynamics, offering fresh perspectives on the symbiotic relationship between digital culture and traditional beliefs, underscored by data from a maximum purposeful sampling of thirty (30) participants. Overall, this exploration emphasizes digital culture's dynamic role in shaping and reflecting cultural convictions, contributing to the understanding of cultural dynamics and evolving digital ethnography in the academic landscape.

Abstract: The chemical mechanical polishing (CMP) has been widely used for surface modification of critical materials and components and provided global planarization of topography with a low post-planarization slope high quality and efficiency. The colloidal silica slurries play an important role in the finishing processes of optical components. Monodisperse mesoporous silica nanospheres were synthesized with different surfactant by Stöber method. Their architectural features and texture parameters were characterized by XRD, FTIR, N2 adsorption–desorption isotherms, SEM, XPS, and TGA techniques. The spherical SiO2 products presented with the controllable 50-150 nm particle size and distribution. The AFM micrographs reveal that flat and smooth surfaces without distinct scratches residual particles are achieved by using the as-obtained composite particles as abrasives[The particle size of SiO2 slurry plays a critical role in the chemical-mechanical polishing process.

Tomato brown rugose fruit virus (ToBRFV) is a causal agent of severe emergent diseases in Solanaceae hosts with agronomic relevance, such as tomato and pepper. Herein, we analyzed the seed transmission rate and efficacy of different seed disinfection treatments and performed a comparison of molecular biology techniques seeking rapid and sensitive detection in seed lots. We evaluated several total RNA extraction and RT-PCR protocols using a distinct combination of PCR primers to test for the presence of the ToBRFV Mexican strain in tobacco host. Our results showed that the percentage of seed and seedlings transmission was less than 1% and that a 3% sodium hypochlorite solution was effective as a seed disinfection treatment. Finally, the most sensitive molecular method identified for virus detection consisted of a CTAB-Trizol RNA extraction followed by nested PCR using primers reported by Dovas et al. (2004). Additionally, we tested potential natural hosts in selected Cucurbitaceae and Solanaceae species. Our results showed that the ToBRFV Mexican strain is capable of experimentally infecting eggplant (Solanum melongena), tomatillo (Physalis ixocarpa), and tobacco (Nicotiana rustica).

Shape of supracondylar fracture of the humeral of pediatric patients is analysed with Procrustes method. XR–images of fractures are considered both in anterio-posterior (AP) view (66 images) and in a lateral (L) view (24 images). Applying Procrustes method for both views mean images are constructed and compared. Variability of shapes is quantified with a shape principal component analysis. Non-parametric tests (permutational and bootstrap) do not indicate statistical difference between Procrustes mean shapes in anterio-posterior and lateral projections. It is shown, however, that AP and L shapes of humeral fractures differ in their variability quantified by shape principal components.

The Homotopy Analysis Method (HAM) is a useful method to derive analytical approximate solutions of black holes in modified gravity theories. In this paper, we study the Einstein-Weyl gravity coupled with Maxwell field, and obtain analytical approximation solutions for charged black holes by using the HAM. It is found that the analytical approximate solutions are sufficiently accurate in the entire spacetime outside the black hole's event horizon, and also consistent with numerical ones for charged black holes in the Einstein-Maxwell-Weyl gravity.

Rivaroxaban and aspirin are commonly used antithrombotic agents that are used in combination for the prevention of coronary artery disease (CAD) and atherothrombotic events in adult patients after an acute coronary syndrome (ACS) with elevated cardiac biomarkers, or with coronary artery disease (CAD) or symptomatic peripheral artery disease (PAD) in high-risk patients. The recommended dosage is 2.5 mg Rivaroxaban twice daily with 75–100 mg aspirin daily. This study aimed to develop a fixed-dose combination tablet of rivaroxaban (2.5 mg) and aspirin (50 mg) to decrease the patient's pill burden and enhance medication adherence. The product formula was developed based on compatibility studies among the active ingredients and the active ingredients' compatibility studies. The formula and the manufacturing procedure were chosen based on the risk assessment for each active substance, wet granulation with both actives intragranular was found to have faster dissolution than direct mix formulae. Furthermore, a validated reverse-phase HPLC stability indicator method was developed to detect APIs and their possible degradants in the formula.

Voids in face-centered cubic (fcc) metals are commonly assumed to form by the aggregation of vacancies; however, the mechanisms of vacancy clustering and diffusion are not fully understood. In this study, we use computational modeling to provide a detailed insight into the structures and formation energies of primary vacancy clusters, mechanisms and barriers for their migration in bulk copper, and how these properties are affected at simple grain boundaries. The calculations were carried out using Embedded Atom Method (EAM) potentials and Density Functional Theory (DFT) and employed the Site-Occupation Disorder code (SOD), the Activation Relaxation Technique nouveau (ARTn) and the Knowledge Led Master Code (KLMC). We investigate stable structures and migration paths and barriers for clusters of up to six vacancies. Migration of vacancy clusters occurs via hops of individual constituent vacancies with di-vacancies having a significantly smaller migration barrier than mono-vacancies and other clusters. This barrier is further reduced when di-vacancies interact with grain boundaries. This interaction leads to the formation of self-interstitial atoms and introduces significant changes into the boundary structure. Tetra-, penta-, and hexa-vacancy clusters exhibit increasingly complex migration paths and higher barriers than smaller clusters. Finally, the direct comparison with the DFT results shows that EAM can accurately describe the vacancy-induced relaxation effects in the Cu bulk and in grain boundaries. Significant discrepancies between the two methods were found in structures with a higher number of low-coordinated atoms, such as penta-vacancies and di-vacancy absortion by grain boundary. These results will be useful for modeling the mechanisms of diffusion of complex defect structures and provide further insights into the structural evolution of metal films under thermal and mechanical stress.