Flotation of small particles is one of the global challenges facing the mineral raw materials processing industry. Large amounts of non-ferrous and rare metals are lost in the flotation tailings in the form of mineral particles below 15 µm in size as a result of the low effectiveness of their capture by coarse bubbles generated in conventional flotation machines. The method of combined microflotation, which is being developed in recent years, uses not only coarse but also microbubbles (MB) produced in the stand-alone generator of air-in-water microdispersion, which serves as the flotation carriers. Depending on the dose of MB, the effect of their application may be both positive, but also negative. The theoretical analysis of various mechanisms of particle transfer onto the surface of coarse bubbles and further into the froth layer allowed to obtain the formula for the optimal MB dose f=2dddpρp, where dd is MB size; dp and ρp respectively are the size and the density of particles. Experiments performed on the copper ore flotation tailings at the Atalaya Mining (Spain) and Chaarat Kapan (Armenia) concentrators showed that, besides the optimal MB dose in the range of 1-3 ml/g, there is another optimal MB dose in the range of 10-20 ml/g, where the copper recovery increases by several percent compared to the reference test (f= 0). In the area between the optimal MB doses, the deep minimum in copper recovery is observed, which value is by several percent lower compared to the value in the reference test.

Scale inhibitors are deployed as preventive and rejuvenation operation in oil and gas industry when production operations are under threat or menace of scale blockage. The application of scale inhibitors is carried out through a method known as squeezing. In general, the squeeze process is governed by inhibitor-rock interaction which is described by adsorption/desorption isotherm. Most reservoirs produce loose sand grains or fine sand which float and flow within the pore spaces along with the squeezed scale inhibitors. Hypothetical reports have shown that not all scale inhibitors pumped into the formation adsorb onto the formation rock. A number of factors (irreversible adsorption, pH changes, competing ions, concentration and temperature) have been considered to affect the adsorption and return profile of these scale inhibitors. This review work examines the performances of most common scale inhibitors used in the oil and gas production activities, theoretical application in reservoirs and how loose fine sand grains affect the adsorption and desorption characteristics of squeezed scale inhibitors. Additionally, presented were overviews of previous reports on fine sand production and migration of fine sands through formation pores in reservoirs.

The fluid seepage in local-saturated zone of subgrade promotes the migration of fine particles in the filler, resulting in the change of pore structure and morphology of the filler and the deformation of solid skeleton, which affects the fluid seepage characteristics. Repeatedly, the muddy interlayer, mud pumping and other diseases are finally formed. Based on the theory of two-phase seepage, the theory of porous media seepage, and the principle of effective stress in porous media, a two-phase fluid-solid coupling mathematical model in local-saturated zone of subgrade considering the effect of fine particles migration is established. The mathematical model is numerically calculated with the software COMSOL Multiphysics○R, the two-phase seepage characteristics and the deformation characteristics of the solid skeleton in local-saturated zone of the subgrade are studied. The research results show that due to the continuous erosion and migration of fine particles in local-saturated zone of the subgrade, the volume fraction of fine particles first increases then decreases and finally becomes stable with the increase of time. And the volume fraction of fine particles for the upper part of the subgrade is larger than that for the lower part of the subgrade. The porosity, the velocity of fluid, the velocity of fine particles, and the permeability show a trend of increasing first and then stabilizing with time; the pore water pressure has no significant changes with time. The vertical displacement increase first and then decrease slightly with the increase of time, and finally tend to be stable. For a filler with a larger initial volume fraction of fine particles, the maximum value of the volume fraction of fine particles caused by fluid seepage is larger, and the time required to reach the maximum value is shorter. It can be concluded that in actual engineering, the volume fraction of fine particles in the subgrade filler should be minimized on the premise that the filler gradation meets the requirements of the specification.

An effective method for coating textile fabrics with porous materials is proposed, and the removal rates of nitrogen oxides (NOx), sulfur oxides (SOx), and fine dust particles in the coated textile fabrics are evaluated. The textile fabrics made of polyester are used to effectively reduce fine dust particles through static electricity. Zeolite and coconut shell activated carbon are used as porous material to reduce SOx and NOx, respectively. The effects of the epoxy content and dilution solution types on the SOx removal rate of textile fabrics coated with zeolite are evaluated to determine the optimum coating conditions. In addition, the effects of external environmental conditions, such as washing and freeze thawing, on the SOx and NOx removal rates of the textile fabrics coated with porous materials using the optimum coating conditions are examined. The test results show that the SOx removal rate of textile fabrics coated with zeolite decreases with the increase in the epoxy content. The decrease is 2.9 times larger for textile fabrics coated using deionized water than those coated using isopropyl alcohol. After one wash, the SOx removal rate decreases dramatically. However, the decrease is reduced by 16% when the epoxy content ratio is increased by 0.5%. The effects of washing and freeze thawing on the SOx and NOx removal rates of textile fabrics coated using the deionized water diluted with the epoxy content ratio of 2% are minimal. Consequently, to maintain stable SOx and NOx removal rates under external environmental conditions such as washing and freeze thawing, 98% deionized water dilution and 2% epoxy content ratio are required for the optimum coating of textile fabrics with zeolite and coconut shell activated carbon.

In this paper any superalgebra is generalized to a new form, namely ultra algebra. We study some algebraic structure results for ultra algebras and we have defined some maps on ultra algebras to know ultra derivation and Jordan ultra derivation. Moreover on certain assumptions we have proved that Jordan ultra derivation is an ultra derivation.

Estimating the infection risks in indoor environments comprises the assessment of the behavior of virus-laden aerosols, i.e. spreading, mixing, removal by air purifiers etc. A promising experimental approach is based on using non-hazardous surrogate aerosols of similar size, e.g. salt particles, to mimic the virus aerosol behavior. This manuscript addresses the issue how a successful transfer of such experiments can be accomplished. Corresponding experiments in two very different environments, a large community hall and a seminar room, with optional use of air purifiers in various constellations were conducted. While high particle concentrations are advantageous in terms of avoiding influence of background aerosol concentrations, it is shown that appropriate consideration of aggregation and settling are vital to theoretically describe the experimentally determined course of particle concentrations. A corresponding model equation for a well-mixed situation is derived and the required parameters are thoroughly determined in separate experiments independently. It is demonstrated that clean air delivery rates (CADR) of air purifiers determined with this approach may differ substantially from common approaches not explicitly taking into account aggregation.

Fine-tuning is an important technique in transfer learning that has achieved significant success in tasks that lack training data. However, as it is difficult to extract effective features for single-source domain fine-tuning when the data distribution difference between the source and the target domain is large, we propose a transfer learning framework based on multi-source domain called adaptive multi-source domain collaborative fine-tuning to address this issue. This approach utilizes multiple source domain models for collaborative fine-tuning, thereby improving the model's feature extraction capability in the target task. Specifically, this approach employs an adaptive multi-source domain layer selection strategy to customize appropriate layer fine-tuning schemes for the target task among multiple source domain models. The objective is to extract more efficient features. Furthermore, a novel multi-source domain collaborative loss function is designed to facilitate the precise extraction of target data features by each source domain model. Simultaneously, it works towards minimizing the output difference among various source domain models, thereby enhancing the adaptability of the source domain model to the target data. In order to validate the effectiveness of the proposed the adaptive multi-source domain collaborative fine-tuning framework, it is analyzed and compared with the most widely used fine-tuning methods by applying them to seven publicly available visual categorization datasets commonly employed in transfer learning. Experimental results demonstrate that, in comparison with the existing fine-tuning approaches, our method not only enhances the accuracy of feature extraction in the model but also provides precise layer fine-tuning schemes for the target task, resulting in state-of-the-art performance.

Digital-based differential amplifiers (DDA) are particularly suitable to low voltage digital integrated circuit technologies. This paper presents an exhaustive analysis of the digital-based analog amplifiers to take advantage of today's high-performance digital technologies and of computer-aided design (CAD) commonly employed to design integrated circuits. The operating principle and the main mathematical relations of the digital-based differential amplifiers are discussed along with an exhaustive explanation of its operating regions and of the corresponding power consumption. Finally, a detailed description of the design procedure of in UMC 180nm standard CMOS technology is shown.

UHPC is a type of cement-based composite used in new construction and/or rehabilitation of existing buildings to extend service life. It is a novel composite material that can serve as an alternative to concrete construction in hostile climates. Following decades of study and production, a diverse variety of commercial UHPC compositions are now available globally to meet the rising number of applicants and demand for high-quality building materials. Although UHPC offers major benefits over normal concrete, its utilization is restricted due to restrictive design rules and exorbitant costs. As a result, a thorough examination of the durability properties of UHPC is required to give important information for material testing requirements and processes, as well as to broaden its practical uses. This report is aimed at increasing basic understanding of UHPC and supporting more UHPC research and applications.

Our existence depends on a variety of constants which appear to be extremely fine-tuned to allow for the existence of life as we know it. These include the number of spatial dimensions, the strengths of the forces, the masses of the particles, the composition of the Universe and others. On the occasion of the 300^th anniversary of the death of G.W. Leibniz we discuss the question of whether we live in the "Best of all possible Worlds". The hypothesis of a multiverse could explain the mysterious fine tuning of so many fundamental quantities. Anthropic arguments are critically reviewed.

The purpose of this study was to conduct a meta-analysis that shows the influence of fiber on ultimate compressive strength and tensile strength of ultra-high performance concrete. The internet scholarly search engines and ScienceDirect article references were used to illustrate the papers concerning the experimental investigations of mechanical properties of ultra-high strength concrete with and without fiber with clearly, completely and comparative raw data. The normal concrete test results were dismissed from this search. Seven trials were identified based on the adopted inclusion and exclusion criteria above. The meta-analysis based on standardized mean difference was carried out on the basis of a fixed-effects model for the major outcomes of the ultimate compressive and tensile properties of ultra-high performance concrete. A total of 888 test specimens were enrolled in these seven trials. The combined analysis yielded a sign of a significant improvement in ultimate compressive strength and tensile strength of ultra-high strength concrete with fiber addition of 2% by concrete volume. The summary effect size of ultimate compressive strength was 2.34 while a more improvement in term of tensile strength with effect size of 2.64. By addition fiber of 2% provides a significant benefit in mechanical properties of ultra-high performance concrete.

More people around the world now have obesity than suffer from starvation thanks to our modern food system. Agriculture was transformed over the 20^th century by a variety of technological advancements that relied heavily on fossil fuels. In the United States of America, government policies and economic incentives led to surplus production of cheap inputs to processed food industries that produced a wide variety of heavily marketed, convenient, rewarding, timesaving, and relatively inexpensive ultra-processed foods. The energy available in the United States food supply increased much more than population needs, albeit with large inequities in food distribution and nutrition security. While most of the rise in per capita food availability during the late 20^th and early 21^st centuries in the United States resulted in increased food waste, a variety of mechanisms have been proposed by which changes in the increasingly ultra-processed food environment resulted in excess energy intake disproportionately in people genetically susceptible to obesity. As populations continue to grow, substantial investments in coordinated nutrition and agricultural research are needed to transform our current food system to one that relies less on fossil fuels, preserves biodiversity, ensures environmental health, and provides equitable access to affordable, safe, and nutritious food that reduces the prevalence of chronic diseases like obesity.

The purpose of this project was to demonstrate the potential of converting an existing internal combustion engine for hydrogen operation at relatively low cost and to optimize the combustion process for ultra-low NOx emissions. The conversion has been carried out on a 450cc naturally aspirated single cylinder engine. The first baseline measurements and setup have shown lower NOx emissions than the baseline gasoline engine (without catalytic converter) for similar power output and engine efficiency. Further optimization of the combustion process allowed to achieve Euro VI and (latest European Commission proposal) Euro VII heavy-duty NOx limits without exhaust gas aftertreatment system (EATS) in steady state conditions. The concept is very promising and the knowledge gained should allow for further optimization to achieve near zero NOx emissions at high engine efficiency and power output with supercharging. It should also allow an efficient conversion of other engine types for different applications. In particular, a project with the aim to convert a heavy duty 6 cylinder engine intended for public transport buses has started. It follows a feasibility study which has shown the competitiveness of the hydrogen engine for this application.

Many applications in the context of Industry 4.0 require precise localization. However, indoor localization remains an open problem, especially in complex environments such as industrial environments. In recent years, we have seen the emergence of Ultra WideBand (UWB) localization systems. The aim of this article is to evaluate the performance of a UWB system to estimate the position of a person moving in an indoor environment. To do so, we implemented an experimental protocol to evaluate the accuracy of the UWB system both statically and dynamically. The UWB system is compared to a ground truth obtained by a motion capture system with a millimetric accuracy.

In this paper, we leverage state of the art models on Imagenet data-sets. We use the pre-trained model and learned weighs to extract the feature from the Dog breeds identification data-set. Afterwards, we applied fine-tuning and dataaugmentation to increase the performance of our test accuracy in classification of dog breeds datasets. The performance of the proposed approaches are compared with the state of the art models of Image-Net datasets such as ResNet-50, DenseNet-121, DenseNet-169 and GoogleNet. we achieved 89.66% , 85.37% 84.01% and 82.08% test accuracy respectively which shows the superior performance of proposed method to the previous works on Stanford dog breeds datasets.

(1) Background: Ultra-endurance exercise involves a high physical impact, resulting in muscle damage, inflammatory response and production of free radicals that alter the body's oxidative state. Supplementation with antioxidants, such as beetroot, may improve recovery in ultra-endurance runners. The aim of this study was to determine whether there is a correlation between the beetroot intake and the recovery of serum oxidative status, inflammatory response and muscle damage parameters after an ultra-endurance race. (2) Methods: An observational and longitudinal study was conducted by means of surveys and blood samples collected from 32 runners during the IX Penyagolosa Trails CSP® race and the two following days. The variables C-reactive protein (CRP), lactate dehydrogenase (LDH), creatine kinase (CK), the activity of the antioxidant enzymes glutathione peroxidase (GPx) and glutathione reductase (GR), as well as the oxidative damage markers malondialdehyde (MDA), carbonyl groups (CG) and loss of muscle strength using the Squat Jump test (SJ) were analyzed to discriminate whether beetroot consumption can modulate the recovery of ultra-trail runners. (3) Results: Significant differences were observed between runners who ingested beetroot and those who did not, in terms of oxidative status, specifically in serum GPx activity at 24 and 48 hours, muscle damage variables CK and LDH and in SJ test at the finish line. Therefore, the intake of supplements containing beetroot positively influences the recovery of serum oxidative status and muscle damage after ultra-endurance running.

This article explores the implementation of high accuracy GPS denied Ad-Hoc localization. There is little research on Ad-Hock UWB-enabled localization systems with mobile and stationary nodes. This work aims to demonstrate the localization of bicycle-modeled robots in a non-static environment through a mesh network of mobile, stationary robots and ultra-wideband sensors. The non-static environment adds a layer of complexity when actors can enter and exit the node’s field of view. The method starts with an initial localization step where each unmanned ground vehicle (UGV) uses the surrounding, available anchors to derive an initial local or, if possible, global position estimate. The initial localization uses a simplified implementation of the iterative multi-iteration Ad-Hoc Localization System (AHLos). This estimate was refined using an unscented Kalman filter (UKF) following a constant turn rate and velocity magnitude model (CTRV). The UKF fuses the robot’s odometry and the range measurements from the Decawave ultra-wideband receivers stationed on the network nodes. Through this position estimation stage, the robot broadcasts to its neighbors its estimated position to help the others further improve their localization estimates and localize themselves. This wave-like cycle of nodes helping to localize each other allows the network to act as a mobile Ad-Hoc localization network.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

Unhealthy diet is an important health problem in the region of the Americas, and Uruguay does not escape this reality. Nutritional problems in Uruguayan school-age children are overweight and obesity. Caloric intake is excessive for 60% of children and 28% of calories come from ultra-processed products (UPP) [CODICEN 2021] [MIDES 2020) (Köncke, Toledo, 2021). In 2018, an evaluation of food intake was conducted in a representative sample of public schools in the city of Montevideo. Food and preparations were categorized according to the NOVA system, later they were analyzed according to the Pan American Health Oganization nutrient profile model (PAHO NPM). Only 0.52% of children consumed exclusively natural foods, unprocessed, minimally processed or culinary ingredients. Twenty-five percent of children consumed ≥ 4 products categorized with excessive content of free sugars, total fat or saturated fat according to the PAHO NPM; in the case of excessive sodium this was 40%. In general, children who included products with excessive free sugars, sodium or saturated fat in their diet exceeded the limits established by PAHO and as a result their diet is of poorer nutritional quality compared to children who did not consume such products.

We report a very frugal microscope building method from easily realizable parts. We show a highly portable field ready compound type microscope with bright field, dark field and projection microscopy capabilities. It has good resolution and magnification for multiple aspects of education and diagnosis. We demonstrate that such a system can be built from simple lenses in laser pointers and camera modules with no specific 3d printed parts or costly lenses. We show all the parts of the system like stage, coarse and fine focussing system, microscope body, even slides can be built from commonly available materials like soda bottle and DVD disks. We list alternate, safer and easily available staining methods and chemicals. The microscope is developed with a target that it can be self-developed even in rural areas of the world with only resources at one’s disposal with very little education. This features a stable focussing and panning system for comfortable viewing through eyes and also easy imaging with a smartphone. We show its utility for microorganism analysis and potential for clinical diagnosis.

The analysis of particulate matter (PM) in dilute solutions is an important target for environmental, geochemical and biochemical researches. Here we show how the microdrop technology may allow to control, through the evaporation of small droplets, the deposition of insoluble materials dispersed in a solution on a well-defined area with a specific spatial pattern. Using this technology the superficial density of the deposited solute can be accurately controlled. In particular, it becomes possible to deposit an extremely reduced amount of insoluble material -in the order of few μg- on a confined area, thus allowing a relatively high superficial density to be reached within a limited time. In this work we quantitatively compare the microdrop technique for the preparation of particulate matter samples with the classical filtering technique. After having been optimized, the microdrop technique allows to obtain a more homogeneous deposition and limit sample consumption of a factor ~25. This method is potentially suitable for many novel applications in different scientific fields.

Registration of the flow pattern fine structure and the matter distribution of a free falling liquid drop in a target fluid at rest in the impact mode of coalescence, when the kinetic energy of the drop exceeds its available potential surface energy (APSE), was carried out by photo and video recording. The main attention was paid to the study of the flow structure at the initial stage of the cavity formation. To carry out color registration, the flow pattern was illuminated by several matrix LED and fiber optic sources of constant light. The planning of experiments and interpretation of the results were based on the properties of the complete solutions of the fundamental equations of fluid mechanics system, including the transfer and conversion of energy processes. Complete solutions of the system of equations describe large-scale flow components that are waves or vortices as well as thin jets (ligaments, filaments, fibers, trickles). In experiments, the jets are accelerated by the converted available potential surface energy (APSE) when the free surfaces of merging fluids were eliminated. The experiments were performed with the coalescence of water, solutions of alizarin ink, potassium permanganate, copper sulphate or iron sulphate drops in deep water. In all cases, at the initial contact, the drop begins to lose its continuity and breaks up into a thin veil and jets, the velocity of which exceeds the drop contact velocity. Small droplets, the size of which grows with time, are thrown into the air from spikes at the jet tops. On the surface of the liquid, the fine jets leave colored traces that form linear and reticular structures. Part of the jets penetrating through the bottom and wall of the cavity forms an intermediate covering layer. The forming layer jets are separated by interfaces of the target fluid. The processes of molecular diffusion equalize the density differences and form an intermediate layer with sharp boundaries in the target fluid. All noted structural features of the flow are also visualized when a fresh water drop isothermally spreads in the same tap water. The fast-changing and finely structured diffuse boundary of merging fluids, which at the initial stage has a complex and irregular shape, is gradually smoothed out by molecular diffusion processes. The similar flow patterns were observed in all performed experiments, however the geometric features of the flow depend on the individual thermodynamic and kinetic parameters of the contacting fluids.

These years have witnessed growing research on applying rheology in grinding and flotation treatment of finely disseminated ores. The slurry rheology has long been identified as the comprehensive effect of inter-particle interactions, including their aggregation (coagulation and flocculation) and dispersion states in slurry, which are more impactive under the fine-particle effect. In this regard, rheology has the potential to play a significant role in interpreting the flowing and deforming phenomenon of inter-particle aggregates, particle-bubble aggregates, and flotation froth. Though much attention has been paid to the rheological effect in industrial suspension, this has not been the case for mineral grinding and flotation for fine particles. The influential mechanism of rheology on the sub-processes of mineral processing has not been systemically concluded and revealed thoroughly, without which the underpinning mechanism for enhancing the processing efficiency has been difficult to discover. This paper reviews the current application and importance of rheology in the fine mineral processing, and the potential research direction in the field is proposed.

The identification and quantitative determination of wool and fine animal fibers are of great interest in the textile field because of significant price differences between them and common adulterations in raw and processed textiles. Since animal fibers have remarkable similarities in their chemical and physical characteristics, specific identification methods have been studied and proposed following advances in analytical technologies. The identification methods of wool and fine animal fibers are reviewed in this paper and the results of relevant studies are listed and summarized, starting from classical microscopy methods which are still used today not only in Small to Medium Enterprises but also in large industries, research studies and quality control laboratories. Particular attention has been paid to image analysis, Nir spectroscopy and proteomics which constitute the most promising technologies of quality control in the manufacturing and trading of luxury textiles and can find application in forensic science and archeology.

Objective: We aimed to clarify the differences in the association between re-admission for heart failure (HF) and left atrial (LA) overload indices by sex in heart failure and a preserved ejection fraction (HFpEF). Methods: We analysed 898 HFpEF patients hospitalized for acute decompensated HF. Blood tests and transthoracic echocardiography were performed before discharge. The primary endpoint was re-admission for HF during the first year. Results: The ratio of diastolic elastance to arterial elastance (p=0.014), a relative index of LA pressure overload, in men and LA volume index (LAVI, p=0.020) in women were significant for re-admission for HF during the first year in the multivariable Fine-Gray analysis. Stroke volume (SV)/LA volume (LAV), another index for LAV overload, was not a significant prognostic factor of re-admission for HF during this time. Conclusion: LA overload was an important prognostic factor for HF re-readmission during the first year after enrolment in patients with HFpEF, but the indices relating to LA overload differed by sex.

We investigated preschool-aged children’s understanding of early fractional tasks and how that performance correlates with fine motor skills and use of gestures while counting. Participants were 33 preschoolers aged 4 to 5 in two Southeastern public elementary schools. Children were tested individually in an interview-like setting. Mathematics tasks were presented in a paper and pencil format and the Grooved Pegboard test assessed fine motor skills. Finally, utilization of gestures was evaluated by taking a behavioral rating of the child’s hand morphology, accuracy of gestures, and synchrony of gestures and spoken word while performing a counting task. Results indicate performance on fractional reasoning tasks significantly predicts both fine motor ability and accuracy of gestures.

Our understanding and theoretical interpretation of observations in astrophysics and cosmology depends on our knowledge of the fundamental constants and their possible dependence on time and space. Atomic spectroscopy and radio astronomy give important information on the validity and stability of the fundamental constants. The possible dependence of the fine structure constant alpha on time and spatial direction is an active topic of research.Period doubling is a universal property of nonlinear dynamical systems, and the doubling is exact in principle. The value of the elementary charge squared can be calculated by the period doubling process from the Planck charge and thereby the value of alpha.If ‘old’ and ‘new’ electrons are identical, then the Planck charge, i.e. a set of natural constants, has remained constant over time. In this article we show that the value of alpha calculated from the Planck charge is 0.007 % smaller than the current accepted value of alpha.

Due to metal leaching and poor catalyst stability, the chemical industry’s fine chemical and pharmaceutical sectors have been historically reluctant to use supported transition metal catalysts to manufacture fine chemicals and active pharmaceutical ingredients. With the advent of new generation supported metal catalysts and flow chemistry, we argue in this study, this situation is poised to quickly change. Alongside heterogenized metal nanoparticles, both single-site molecular and single-atom catalyst will become ubiquitous. This study offers a critical outlook taking into account both technical and economic aspects.

Ultraviolet (UV) light with a wavelength of 254 nm has proven to be effective at inactivating microorganisms, and thus has been increasingly employed as a method of disinfection for indoor environments. Solar UV wavelengths (300 to 400 nm) are known to initiate the formation of secondary organic aerosol (SOA) particles from photo-oxidation of volatile organic compounds in the atmosphere, but germicidal wavelengths have not been extensively studied for indoor environments. In this work, toluene was exposed to 254 nm UV light in a laboratory photoreactor, with varying conditions of the air, the duration of UV exposure, and the duration of post-UV time. The number of particles formed in the fine particulate matter (PM2.5) size range was measured, and significant levels of particle formation were observed for UV exposure periods of as short as 5 minutes. The particle formation ranged from 2.4x10⁶ particles/m³ for 5 minutes of UV exposure, to 1449.8x10⁶ particles/m³ for 15 minutes of UV exposure. Particle formation was found to increase with increasing concentrations of gas phase toluene, and at relative humidity of approximately 20% and higher. Variations in the initial number of particles present did not appear to have a significant effect on the particle formation, suggesting that nucleation was not a controlling factor. However, tests in a commercial environment showed no significant detectable PM2.5 formation, indicating that SOA formation during the intermittent use of germicidal UV may not significantly affect indoor air quality.

This paper reviews several techniques, including analytical theories and real frequency techniques, to design ultra-wideband impedance matching networks for low-power applications. The comparison of solutions obtained using the simplified real frequency technique to the published solution using Chebyshev filter theory is demonstrated.

Background: The level of food processing has gained interest for a potential determinant of human health. The aim of this study was to assess the relation between level of food processing and prostate cancer severity. Methods: A sample of 120 consecutive patients were examined for their dietary habits assessed through validated food frequency questionnaires, their dietary intake of food groups categorized according to the NOVA classification, and the severity of prostate cancer according to the European Association of Urology (EAU) guidelines groups risk. Uni- and multivariate logistic regression analyses were performed to test the association between the variables of interest. Results: Individuals reporting higher consumption of unprocessed/minimally processed foods were less likely to have worse prostate cancer severity than lower consumers in the energy-adjusted model [odds ratio (OR) = 0.38, 95% confidence interval (CI): 1.17-0.84, P = 0.017 and OR = 0.33, 95% CI: 0.12-0.91, P = 0.032 for medium/high vs. low grade and high vs. medium/low grade prostate cancers, respectively); however, after adjusted for potential confounding factors, the association was no more significant (Table 4). A borderline association was also found between higher consumption of UPF and worse prostate cancer severity in the energy-adjusted model (OR = 2.11, 95% CI: 0.998-4.44; P = 0.051), but again the association was no more significant after adjusting for the other covariates. Conclusions: The level of food processing seems not to be independently associated with prostate cancer severity, while potentially related to other factors that need further investigation.

As solar energy is a low-cost and clean energy source, there has been a great deal of interest in how to harvest it. To absorb solar energy efficiently, we have designed a broadband metamaterial absorber based on the principle of Fabry–Pérot (FP) cavity and surface plasmon resonances (SPRs). We propose a broadband perfect absorber consisting of a four-layer structure of silica-tungsten-silica-titanium (SiO2-W-SiO2-Ti) for the incident light wavelength range of 300–2500 nm. The structure achieves perfect absorption of incident light in the wavelength range of 351.8–2465.0 nm (absorption >90%), with an average absorption of 96.3%. The advantage of our proposed structure is that it combines the characteristics of both high and broadband absorption and has a high overall absorption efficiency for solar radiation. It is also independent of polarization and insensitive to incident angle. We investigated how absorption was affected by different structures, materials, geometrical parameters, and refractive indices for different dielectric materials, and we explored the reasons for high absorption. This structure is refractory and ultra-thin, and it offers a good trade-off between bandwidth and absorption. It therefore has premium application prospects and value.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

Fabrics treated to repel water, superhydrophobic, and water and oil, superamphiphobic, have numerous industrial and consumer-level benefits. These coatings are typically non-permanent. This is largely due to chemical or physical changes of the coating to prolonged exposure to relatively harsh environments. To develop more durable fabric treatments for specific applications, it is necessary to measure the extent to which the treated fabrics retain their low-wettability after being subjected to controlled aggressive environmental conditions. In this study, plain weave fabrics made from polyester filaments and coated with silicone nanofilaments in-solution were exposed to aerodynamic icing conditions. The coated fabrics showed superhydrophobic behavior, or superamphiphobic for those that were fluorinated. The wettability of the fabrics was progressively evaluated by contact angle and roll-off-angle measurements. The fabrics were able to maintain their low-wettability characteristics after exposure to water droplet clouds at airspeeds up to 120 m/s, despite damage to the silicone nanofilaments, visible through scanning electron microscopy.

An ultra-low anti-reflection optical coating on both surfaces of a plastic cover slip was studied for use in confocal image measurement. The optical reflectance at a wavelength of 632.8 nm was less than 0.1% when the coated sample was placed in a liquid having a refractive index of 1.34 close to the aqueous solution of the biomaterial. The high- and low-index coating films, Substance-2 (PrTiO3) and silicon dioxide (SiO2), were measured by an ellipsometer to determine their optical refraction indices and extinction coefficients. Theoretically, when the two layer thicknesses are designed using the optical admittance diagram of the cover slip to approach the equivalent index of 1.34, a reflectance of 1.6×10-5% in the liquid could be obtained. Experimentally, the reflectance of the sample deposited on the two faces of the cover slip was 4.223±0.145% as measured in the air; and 0.050±0.002% as measured by a He-Ne laser in the liquid.

Low-cost monitors have made possible for the first time measurements of long-term (months to years) potential indoor exposures to fine particles. Indoor and outdoor measurements made over nearly 5 years (2017-2021) by the largest network of low-cost monitors in the United States (PurpleAir) are compared to the prevalence of adult smokers in 1650 Zip codes within the three West Coast states of California, Oregon, and Washington. The results show that mean indoor exposures above the 75th percentile of adult smoking prevalence are more than 50% higher than those below the 25th percentile. Mean outdoor concentrations are also elevated, but by a smaller amount (20%). Both comparisons are significant at the p<0.001 level. The elevation of the PM2.5 concentrations with increasing smoking prevalence is evidence of environmental disparities in income, education, and other socioeconomic indices..

Vibro-fluidized dry coal beneficiation involves the unavoidable mixing of -1 mm coal dust into the fluidized bed, which compromises the stability and homogeneity of the bed density and reduces the effectiveness of fine-grained coal separation. In order to understand the features of coal powder separation and mixing (-1 mm) in a vibrating fluidized bed, as well as to achieve a uniform and stable bed density, a wide-grained dense medium consisting of -1 mm coal dust and 0.3-0.15 mm magnetite powder was homogeneously mixed in this work. The degree of density separation in the entire bed was examined, as well as the local mixing properties of the Wide-grained Dense Medium. It was discovered that when low vibrational energy was introduced at the same gas velocity, particle separation was enhanced in comparison to the usual fluidized bed. Little bubbles were found to ensnare fine coal dust and migrate upward, increasing density separation. The introduction of high vibrational energy leads to particle disorder within the bed and an increase in the level of particle mixing. The beneficial effects of vibration on the bed are diminished when the gas velocity is gradually increased under specified vibration circumstances. This causes big bubbles to develop more frequently, which increases particle mixing. Among them, the 1-0.5 mm fine-grained coal exhibits the best mixing state; it is less impacted by variations in air velocity and vibration levels, whereas the -0.5 mm coal dust is more affected by each of these variables. Furthermore, a wide range of air velocity regulation without a significant segregation state change was discovered to be achievable by the particle system under vibration circumstances of f=25Hz A=1mm and f=25Hz A=2mm.

In this paper we will provide a new equation that explains why there are three generations or families of leptons and quarks, respectively. We will also explain why all those particles have the known mass ratios amongst their three respective generations and flavors. We will also tackle the problem of Yukawa couplings being arbitrary parameters in the Standard Model Higgs mechanism, which is a long standing problem do to their formulaic dependence on the Higgs Vacuum Expectation Value (VEV). We will attempt to solve this problem and provide a strong argument through an equation for Yukawa couplings of all leptons and quarks via a new methodology that depends on the running of the fine-structure constant on the Q scale, quantum numbers and the Weinberg angle (also on the Q scale). We will also make predictions for all three left-chiral neutrino mass eigenstates and we will provide upper limits for the three right-chiral neutrino mass eigenstates

The research was undertaken to study the way deformation behaves in ultrafine-grained (UFG) conducting Al-Zr alloys doped with Sc, Hf, and Yb. All in all, 8 alloys were studied with zirconium partially replaced by Sc, Hf, and/or Yb. Doping elements (X = Zr, Sc, Hf, Yb) in the alloys total 0.4 wt.%. The choice of doping elements is conditioned by possible precipitation of Al3X particles with L12 structure while annealing these alloys. Such particles provide higher thermal stability of a nonequilibrium UFG microstructure. Initial coarse-grained samples were obtained by induction casting. The UFG microstructure in the alloys was formed by Equal Channel Angular Pressing (ECAP) at 225°C. Superplasticity tests were carried out at temperatures ranging from 300 to 500 °C and strain rates varying between 3.310-4 and 3.310-1 s-1. The highest values of elongation to failure are observed in Sc-doped alloys. A UFG Al-0.2%Zr-0.1%Sc-0.1%Hf alloy has maximum ductility: at 450 °C and a strain rate of 3.310-3 s-1, relative elongation to failure reaches 765%. At the onset of superplasticity, stress–strain curves are characterized by a stage of homogeneous strain and a long stage of localized plastic flow. The dependence of homogeneous strain (eq) on test temperature in UFG Sc-doped alloys is increasing uniformly, which is not the case for other UFG alloys with eq(T) dependence peaking at 350-400 оС. Strain rate sensitivity coefficient of flow stress m is small and does not exceed 0.26-0.3 at 400-500 °C. In UFG alloys containing no scandium, m coefficient is observed to go down to 0.12-0.18 at 500 оС. It has been suggested that lower m values are driven by intensive grain growth and pore formation in large Al3X particles, which develop specifically at the ingot crystallization stage.

There has been considerable research on reconstructing 3D shapes from single-view images; however, preserving the detailed information of the input image remains difficult. In this paper, we propose the application of a gradient map to train a network, aimed at improving the visual quality of fine-grained details such as the thin and tiny components of generated shapes. Each gradient map was created from the original voxel data, and each value represented the amount of information per volume. Here, the gradient map was defined by several methods that mathematically quantify and represent the detailed structure of an object. By applying this map to the loss function in training, we could induce the network to intensively train partial details, such as thin and narrow parts. We demonstrated that the detailed information was well-recovered when a weight that is proportional to the gradient value was applied to the loss. Furthermore, it is expected that our method will contribute to the development of 3D technologies related to the construction of virtual space for simulation and new customer experience.

Text summarization remains a challenging task in the Natural Language Processing field despite the plethora of applications in enterprises and daily life. One of the common use cases is the summarization of web pages which has the potential to provide an overview of web pages to devices with limited features. In fact, despite the increasing penetration rate of mobile devices in rural areas, the bulk of those devices offer limited features in addition to the fact that these areas are covered with limited connectivity such as the GSM network. Summarizing web pages into SMS becomes, therefore, an important task to provide information to limited devices. This work introduces WATS-SMS, a T5-based French Wikipedia Abstractive Text Summarizer for SMS. It is built through a transfer learning approach. The T5 English pre-trained model is used to generate a French text summarization model by retraining the model on 25,000 Wikipedia pages then compared with different approaches in the literature. The objective is twofold: (1) to check the assumption made in the literature that abstractive models provide better results compared to extractive ones; and (2) to evaluate the performance of our model compared to other existing abstractive models. A score based on ROUGE metrics gave us a value of 52% for articles with length up to 500 characters against 34.2% for transformer-ED and 12.7% for seq-2seq-attention; and a value of 77% for articles with larger size against 37% for transformers-DMCA. Moreover, an architecture including a software SMS-gateway has been developed to allow owners of mobile devices with limited features to send requests and to receive summaries through the GSM network.

Is the extensive decline of insects partially due to an insect-specific feature of their functional organization that is disadvantageous for living in an industrialized environment? The unique way in which gases are supplied in insect tissues is such a special trait. It exposes cells directly to the gas phase, via tracheae that end in micro-tubes, the tracheoles, which have diameters in the same range as particles of ultra-fine dust transported by air of industrialized countries. Number and volume of these particles – calculated to be inhaled by honeybees, e.g., – are indicative to locally impede O2-uptake and CO2-release and thus to restrain physiological activities.

The problem of Yukawa couplings being arbitrary parameters in the Standard Model Higgs mechanism is a long standing one due to their formulaic dependence on the Higgs Vacuum Expectation Value. We will attempt to solve this problem and provide a strong argument that the Yukawa couplings of charged leptons and down type quarks are not arbitrary parameters in the SM. A new methodology for predicting the Yukawa couplings will be presented by using Compton wavelengths, the Rydberg Constant and g-factors of charged leptons instead of relying on the Higgs VEV. We will then proceed to rewrite this new method in terms of an empirical formula that depends on the running of the fine-structure constant on the Q scale, charge and lepton quantum numbers and g-factors to predict the values of the Yukawa couplings for all three generations of charged leptons and d-type quarks. We will also touch on the subject of neutrinos both as Majorana and Dirac fermions respectively and make a prediction for the lightest possible Majorana neutrino and the differences between Dirac neutrinos and anti-neutrinos. We conclude that the Yukawa couplings are not arbitrary parameters in the SM and that this new formula provides very accurate results.

This article uses a contemporary and revelatory case study to explore the relationship between three conversations in the innovation literature: design thinking, creativity in strategy and, the emerging area of art-thinking. Businesses are increasingly operating in a VUCA environment where they need to design better experiences for their customers and better outcomes for their firm and the Arts are no exception. Innovation, or more correctly growth through innovation, is a top priority for business and although there is no single, unifying blueprint for success at innovation, design thinking is the process that is receiving most attention and getting most traction. Design thinking teaches businesses to think with the creativity and intuition of a designer; to show a deep understanding of; and have empathy with the user. But design thinking has limitations. By placing the consumer at the very heart of the innovation process, design thinking can often lead to more incremental than radical ideas. Now there is a new perspective emerging, art-thinking, in which the objective is not to design a journey from current scenario; A to improved position: B. Art thinking requires the creation of B and spends more time in the open ended, problem space, staking out possibilities and looking for uncontested space. In Dublin, we examine a case of the oldest, largest and most prestigious fine art gallery and studio where most of the country’s best-known and successful visual artists both make, exhibit and sell their art. Graphic Studio Dublin is primarily a printmaking studio, established by artists over 60 years ago. It has facilities for woodblock, lino-print, silkscreen, intaglio and carborundum etching spread over four floors of a centrally located studio where the artists have access 24/7. But two years ago it found itself on the brink of collapse having borrowed heavily to invest in new facilities during the period of Ireland’s economic collapse. Its loans were sold to a vulture-fund who were about to foreclose in a move that would have seen a generation of Irish Artists displaced. A new board of directors was empaneled and they introduced some art thinking principles to bring the organisation back from the brink. They used an art-thinking mindset and design thinking tools to restore the fortunes of this venerable, artist-led institution and it worked.

Engineering properties of bedrock materials at Badlands National Park were used to develop models for Park managers to assess slope erosion and stability for fossil resource protection. Six fully instrumented sites were used to document slope conditions. Bedrock consisted of Oligocene White River Group rocks. Bulk erosion rates correlated to grain size with silty-sandy materials producing higher mass erosion rates as a function of the silt-to-clay ratio and plastic index. Data indicated that as grain size decreased, plastic index increased leading to a decrease in erodibility. These parameters were used to construct a grain-size proxy, ψ, that was substituted for grain size, D, in Bagnold’s entrainment equation and provided significant improvement in calculation of critical entrainment velocities for fine-grained materials. Hydraulic analyses of slope and pediment surface processes indicated surface roughness was a controlling factor and materials washed from rough steep slopes were effectively transported across smooth low-angle pediments with slope-to-pediment angle ratios of nearly 6:1. Slope stability modeling of ten slopes produced high factors of safety for all slopes, even under saturated conditions and was attributable to clay cohesion. All results were used to construct models that predicted years until net slope erosion equaled 2.5 cm (1 inch). Using these results, Park managers were advised to visit erosion-prone sites on a 1 to 6 year schedule, based on site geology and slope aspect, to adequately protect critical fossil resources from destruction.

The two-stage direct thermal contact (2sDTC) process is a rapid dewatering approach for fluid fine tailings (FFT) that is integrated into an oil sands bitumen extraction plant to reduce tailings pond storage and freshwater usage. In the first stage, combustion gas directly contacts atomized FFT, vaporizing water and yielding dry solids and steam-rich hot gas. The second stage involves pond effluent water directly contacting the steam-rich hot gas, recovering heat and condensing moisture. Case studies confirm the technical feasibility of the integration. Benefits include producing a dry discharge, reducing tailings water discharge and conserving an equivalent to 0.2 barrels of freshwater per barrel of oil produced. Most importantly, these benefits incur no additional energy cost to the plant as the integration eliminates the energy penalty and CO2 emissions associated with FFT dewatering. Further capacity enhancement can be achieved by using centrifuge-concentrated FFT. The study reveals that FFT concentrated to ~50 wt% solids could still maintain its pump-ability and be accommodated by the 2sDTC process, leading to an integration which could dewater more FFT annually and conserve more freshwater ( 0.58 barrels per barrel of oil produced), with the sole energy requirement being the power to drive the centrifuge machinery.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

Hydrogen fuel is gaining particular attention in internal combustion engines. In addition to zero-carbon emissions, major advantages relate to its combustion characteristics, which allow significant increase in thermal efficiency under ultra-lean operation and with very low NOx levels. The ignition system is one of the main technology enablers, as it determines the capability to control ultra-lean operations, avoid backfire phenomena, or reduce the risks of abnormal combustions. The latter results from the hydrogen low ignition energy and it is associated with factors like high-temperature residuals, hot spots, and irregular spark plug discharge. ACIS gen 2-Barrier Discharge Igniter excels in accelerating the initial flame growth speed by the generation of non-equilibrium low-temperature plasma, strong ignition promoter for the combined action of kinetic and thermal effects. Moreover, its volumetric discharge facilitates combustion initiation on a wide region, in contrast to the localized ignition of traditional spark systems. In this work we present for the first time, to the best of our knowledge, experimental results showing the performance of a hydrogen engine with a low-temperature plasma discharge. Tests were conducted on a single-cylinder research engine, achieving ultra-lean conditions with cycle-to-cycle variability results below 2.5%. The analysis indicates that the H2 - BDI combined solution is capable of accelerating the evolution of the flame front compared to traditional spark plugs, leading to a significant reduction in the cycle-to-cycle variability. A meticulous adjustment of the BDI control parameters further enhances igniter performance and contributes to a deeper understanding of the innovative approach proposed in this study.

in this article, an ultra-wideband traveling wave antenna with antipodal topology is proposed. The proposed design is realized on an economical substrate with minimum thickness. The proposed design offers an ultra-wide bandwidth of 26 to 40 GHz, translating to 42%. The dimensions of the antenna are 20mm x10mm x 0.5mm indicating an electrically compact structure. The proposed antenna offers high front to back ratio of at least 10dB across the bandwidth of operation. The forward gain of the antenna varies from 4 to 7dBi in the afore-mentioned band. The pattern integrity is maintained throughout the band. The antenna is fabricated using the commercial photolithography process. A mutli-step topology of the antennas is also proposed for wide angular coverage. The coverage is greater than 150º with mutual coupling less than 25dB. These performance metrics is achieved with a very small footprint. Simulated and experimental results are presented in this paper.

In this work, we present a transceiver front-end in SiGe BiCMOS technology that can provide an ultra-wide bandwidth of 100 GHz at millimeter-wave frequencies. The front-end employs a novel configuration for low-loss distribution of broadband generated pulses as well as coherent spatial combining of received pulses. This leads to the realization of a fully integrated ultra-high-resolution imaging chip for biomedical applications. We realized an ultra-wide imaging bandwidth of 100 GHz by the integration of two adjacent, disjointed frequency sub-bands of 10–50 GHz and 50–110 GHz respectively. The transceiver front-end is capable of both transmit (TX) and receive (RX) operations. This is a key building-block for a scalable system in which a unit cell is repeated in the X and Y directions resulting in less power and area consumption. The imaging elements were designed and fabricated in Global Foundry 130-nm SiGe 8XP BiCMOS process technology.

With the proportional reduction of MOSFET size, the leakage-to-barrier reduction (DIBL) effect leads to a more significant increase in the tunneling current on the gate, and the appearance of the gate tunneling current also seriously affects the static characteristics of the device. In this paper, a new theoretical model of the relationship between the direct tunneling current and the thickness of the oxide layer under the DIBL effect is proposed for the MOSFET device with ultra-thin oxide layer. On this basis, the characteristics of the MOSFET device are studied in detail by using HSPICE, and their working conditions are quantitatively analyzed. The characteristic variation trend of small-size devices under the influence of gate tunneling current is predicted. The simulation results using BSIM4 model are consistent with the theoretical model. The theory and data in this paper will provide useful reference for large scale integrated circuit design.

The modern diet, which consists of food produced with high level of industrial processing, is associated with an increased risk of the development of lifestyle diseases. Current nutritional science is, however, focused on chemical composition of food, and not on the type and degree of processing used during the food production. Here, we take a fresh perspective on the relationship between the extent and type of food processing, and evaluate its impact on consumer health. We argue that the preference for consumption of minimally processed foods, and restriction of ultra-processed foods should be an essential part of a healthy lifestyle, disease prevention, and even treatment. We also present a simple, user-friendly consumer guide, which is intended to be used as a practical, ready-to-go identifier of ultra-processed foods.

Continuous in-home monitoring of older adults living alone aims to improve their quality of life and independence, by detecting early signs of illness and functional decline or emergency conditions. To meet requirements for technology acceptance by seniors (unobtrusiveness, non-intrusiveness, privacy-preservation), this study presents and discusses a new smart sensor system for the detection of abnormalities during daily activities, based on ultra-wideband radar providing rich, not privacy-sensitive, information useful for sensing both cardiorespiratory and body movements, regardless of ambient lighting conditions and physical obstructions (through-wall sensing). The radar sensing is a very promising technology, enabling the measurement of vital signs and body movements at a distance, and thus meeting both requirements of unobtrusiveness and accuracy. In particular, impulse-radio ultra-wideband radar has attracted considerable attention in recent years thanks to many properties that make it useful for assisted living purposes. The proposed sensing system, evaluated in meaningful assisted living scenarios by involving 30 participants, exhibited the ability to detect vital signs, to discriminate among dangerous situations and activities of daily living, and to accommodate individual physical characteristics and habits. The reported results show that vital signs can be detected also while carrying out daily activities or after a fall event (post-fall phase), with accuracy varying according to the level of movements, reaching up to 95% and 91% in detecting respiration and heart rates, respectively. Similarly, good results were achieved in fall detection by using the micro-motion signature and unsupervised learning, with sensitivity and specificity greater than 97% and 90%, respectively.

A novel method based on a hybrid incremental modeling approach has been designed and applied to imbalance detection in ultra-high precision rotating machines. The model is obtained by a two-step iterative process that combines an overall model (least-squares fitting) with a local model (fuzzy k-nearest-neighbour) to take advantage of their complementary capacities. Three normalization strategies of evaluating the effect on accuracy are analyzed. A comparative study demonstrates that the hybrid incremental model provides better error-based performance indices for detecting imbalance than a nonlinear regression model and an adaptive neural-fuzzy inference system model. The suitability of Mahanolobis normalization for hybrid incremental modeling is also demonstrated in this case study. The proposed strategy for imbalance detection is simple, fast, and non-intrusive, reducing the deterioration in the performance of ultra-high precision rotating machines due to vibrations.

The aim of this study was to examine the oxidation of human serum albumin (HSA) caused by oxidative stress after an exhaustive exercise such as ultra-marathon race. Thus, blood samples from 12 adult runners who underwent a 103 km mountain ultra-marathon race were collected pre- and 24, 48 and 72 h post race. HSA was partially purified using affinity chromatography and then was subjected to Western blot analysis for disulfide dimers determination, indicating oxidation. The results were correlated with those from a previous study in which the same samples were analyzed using different oxidative stress markers and a good correlation with protein carbonyls (PC) at all time points was observed. Moreover there was a significant correlation with static oxidation-reduction potential (sORP) at 24 h, and a negative correlation with capacity oxidation-reduction potential (cORP) at 24 and 48 h. In addition, an individual analysis of albumin dimers exhibited great inter-individual differences. This inter-individual variability in the oxidation of HSA may suggest different interventions (e.g. through diet) in order to confront the effects on athletes’ organism after a strenuous exercise. In conclusion, this study supported the importance of the assessment of albumin dimers as a predictive marker for exercise-induced oxidative stress.

In this study, the distribution patterns of southern horse mackerel are examined using commercial fine-scale resolution data. Using landings by size category and VMS data from the Portuguese commercial bottom trawl fishery, which consistently targets horse mackerel, this study provides a comprehensive analysis of horse mackerel age distributions spanning a decade (2010-2020). Importantly, the study addresses potential biases in commercial effort data and establishes the usefulness of commercial bottom-trawl gear as a suitable method for sampling and evaluate southern horse mackerel stock dynamics. Ordered regression models were applied to allow for the modelling of the distribution of multiple age categories and investigate spatio-temporal migrations off the Portuguese coast. Southern horse mackerel shows a widespread age distribution range and stable abundance with indications of seasonal and spatial patterns in the distribution of specific age groups. The insights derived from this research contribute valuable knowledge for understanding the dynamics and distribution patterns of fish populations.

Fine-grained image classification remains an ongoing challenge in the computer vision field, which is particularly intended to identify objects within sub-categories. It is a difficult task since there is a minimal and substantial intra-class variance. The current methods address the issue by first locating selective regions with Region Proposal Networks (RPN), object localization, or part localization, followed by implementing a CNN Network or SVM classifier to those selective regions. This approach, however, makes the process simple by implementing a single-stage end-to-end feature encoding with a localization method, which leads to improved feature representations of individual tokens/regions by integrating the transformer encoder blocks into the Yolov5 backbone structure. These Transformer Encoder Blocks, with their self-attention mechanism, effectively captured the global dependencies and enabled the model to learn relationships between distant regions. This improved the model ability to understand context and captured long-range spatial relationships in the image. We also replaced the Yolov5 detection heads with three transformer heads at the output for object recognition using the discriminative and informative features maps from transformer encoder blocks. We established the potential of the single stage detector for the fine-grained image recognition task, by achieving state of the art 93.4% accuracy, as well as outperforming the existing Yolov5 model. The effectiveness of our approach is assessed using the Stanford car dataset, which includes 16,185 images of 196 different classes of vehicles with significantly identical visual appearances.

Currently available nationwide prediction models for fine particulate matter (PM_2.5) lack prediction confidence intervals and usually do not describe cross validated model performance at different spatiotemporal resolutions and extents. We used 41 different spatiotemporal predictors, including data on land use, meteorology, aerosol optical density, emissions, wildfires, population, traffic, and spatiotemporal indicators to train a machine learning model to predict daily averages of PM_2.5 concentrations at 0.75 sq km resolution across the contiguous United States from 2000 through 2020. We utilized a generalized random forest model that allowed us to generate asymptotically-valid prediction confidence intervals and took advantage of its usefulness as an ensemble learner to quickly and cheaply characterize leave-one-location-out CV model performance for different temporal resolutions and geographic regions. Using a variable importance metric, we selected 8 predictors that were able to accurately predict daily PM_2.5, with an overall leave-one-location-out cross validated median absolute error of 1.20 ug/m³, an R² of 0.84, and confidence interval coverage fraction of 95%. When considering aggregated temporal windows, the model achieved leave-one-location-out cross validated median absolute errors of 0.99, 0.76, 0.63, and 0.60 ug/m³ for weekly, monthly, annual, and all-time exposure assessments, respectively. We further describe the model’s cross validated performance at different geographic regions in the United States, finding that it performs worse in the Western half of the country where there are less monitors. The code and data used to create this model are publicly available and we have developed software packages to be used for exposure assessment. This accurate exposure assessment model will be useful for epidemiologists seeking to study the health effects of PM across the continental United States, while possibly considering exposure estimation accuracy and uncertainty specific to the the spatiotemporal resolution and extent of their study design and population.

Background: Particulate matter and urban air pollution affect the human body and can lead to death. Epidemiological studies should consider the exposure to pollutants and the diverse responses of individuals depending on their sensitivity to the pollutants. Methods: In this study, air pollution measurements were obtained hourly at measuring stations operated by the national and local governments to increase the reliability of the measured values. A β-ray absorption method was used to analyze the measurements of fine dust and determine the particulate matter content. Results: The air pollution data were log-converted to enable the comparison of data from different time periods. The comparison was made, focusing on the period of Seoul's fine dust policy. As a result, the cancer incidence rate also decreased after the policy. The data on individual characteristics were obtained from a survey of Seoul citizens conducted from 2015 to 2016 and using indicators such as the quality of life and social trust of Seoul citizens. Concludions: The survey on the living environment and residence indicated that 80% of the heads of households were men. Women had a greater dissatisfaction than men with the residential, economic, and social environments. The survey questions on well-being were related to the internal and external environment such as air pollution, noise, and fine dust.

Learning dental procedures is a complex task involving the development of fine motor skills. The reported use of theories and/ or evidence for designing learning activities to develop the fine motor skills needed for dental practice is limited. The aim of this review is to explore the available body of knowledge related to learning fine motor skills in dentistry. Evidence from studies investigating motor skill learning highlights the negative impact of self-focus and self-regulation on learning outcomes, particularly during the early stages of learning. The development of activities and schedules that enable novices to demonstrate characteristics similar to experts, without the reported long period of ‘deliberate practice’, is clearly of value. Outcomes of learning implicitly are important in dentistry because working under stressful conditions is common, either during undergraduate study or in practice. It is suggested that learning implicitly in the simulation stage can reduce disrupted performance when transitioning to clinical settings. Therefore, further investigation of effective methods for learning dental fine motor skills is indicated, using approaches that result in robust performance, even under stressful conditions.

Background: Lung cancer is one of the leading causes of morbidity and mortality worldwide with 25% of deaths due to lung cancer occurring in Europe. This study therefore sought to assess the burden of lung cancer by country and to evaluate the magnitude of fine Particulate Matter (PM2.5) and cigarette smoking by country in Europe. Methods: An ecological study nested on the World Health Organization air pollution database 2016 was conducted. We sampled 30 European Countries, with a total of 1625 mean annual samples of Particulate Matter (PM2.5) collected from 1625 designated sites (n = 1625). We further used the ‘World Health Disease Rankings’ database to extract Lung Cancer Morbidity and Mortality Rate by country. We used SAS version 9.4 to indicate the distribution of PM2.5 and Lung Cancer Mortality Rate. Results: Lung cancer Relative Risk (RR) was 1.0 in all never- smokers. RR for Ex-smokers for Adeno carcinoma was 3.5 in males and 1.1 in females, small cell carcinoma was 16.2 in males and 3.8 in females. RR for current smokers for Adeno carcinoma was 8.0 in males and 4.1 in females, small cell carcinoma was 57.9 in males and 18.2 in females. Mean annual PM2.5 by country ranged from 6.01 to 37.28µg/m3 whereas lung cancer mortality rate by country ranged from 19.67 to 54.26 deaths per 100,000 population. Conclusion: Cigarette smoking and exposure to both second hand smoke and high concentration of PM2.5 resulted into increased burden of lung cancer in Europe. Countries should re-strategize to reduce the burden of lung cancer in Europe.

Previous studies have reported certain sex differences in motor performance precision. The aim of the present study was to analyse sex differences in fine motor precision performance for both hands in different tests conditions. 220 Spanish participants (ages: 12-95) performed fine motor tasks - tracing over the provided models – lines of 40 mm for both hands, two sensory conditions (PV – proprioceptive-visual; P – proprioceptive only) and three movement types (F – frontal, T – transversal and S - Sagittal). Differences in line length (the task focused on precision) were observed through MANOVA analysis for all test conditions, both sexes and different age groups. Sex differences in precision were observed in F and T movement types (statistically significance level and higher Cohens’ d was observed in condition with vision). No any statistically significant differences were observed in both hands and sensory conditions in sagittal type. Sex differences in fine motor precision were more frequently observed in the PV sensory condition in the frontal movement type and less in the sagittal one.

The straightness error of guideway is one of the key indicators of ultra-precision machine, which plays an important role in the machining accuracy of work-piece. In order to measure straightness error of long distance ultra-precision guideway accurately, a splicing measurement for straightness error of guideway using high-precision flat mirror and displacement sensor was proposed in this paper, and the data splicing processing algorithm based on coordinate transformation was studied. Then comparative experiments on splicing measurement and direct measurement of straightness error were carried out on a hydrostatic guideway grinder. The maximum difference between the two measurements was about 0.3μm, which was far less than the straightness error of 5.8μm. The experiment demonstrated the correctness of the proposed splicing measurement method and data processing algorithm. To suppress the influence of straightness error on machining accuracy, a straightness error compensation algorithm based on error rotation transformation and vertical axis position correction was proposed, and the grinding experiment of a plane optics with size of 1400mm×500mm was carried out, whose flatness error after grinding was about 2.98μm. The straightness error of the grinding machine had been well suppressed.

Liquid biopsy is a rapidly emerging field which involves the minimal/non-invasive assessment of signature somatic mutations through analysis of circulating tumor DNA (ctDNA) shed by tumor cells in bodily fluids. The broad, unmet need for liquid biopsy lung cancer detection is the lack of multiplex platform that can detect a mutation panel of lung cancer genes using minimum amount of sample, especially for ultra-short ctDNA (usctDNA). Here we developed a non-PCR and non-NGS-based single droplet based multiplexing microsensor technology “Electric Field-Induced Released and Measurement (EFIRM) Liquid Biopsy” (m-eLB) for lung can-cer-associated usctDNA. The m-eLB provides multiplexable assessment of usctDNA within a single droplet of biofluid in only one well of micro-electrodes, as each electrode coated with dif-ferent probes for the ctDNA. In this m-eLB prototype, it demonstrates accuracy for 3 tyrosine ki-nase inhibitor related EGFR target sequences in synthetic nucleotides. The accuracy for the multi-plexing assay has an AUC of 0.98 for L858R, Ex19del, AUC of 0.94 for Ex19 deletion and AUC of 0.93 for T790M. By combining the 3 EGFR assay together, the AUC was 0.97 for the multiplexing assay.

Excessive intake of fat and fatty acids is associated with major health hazards such as obesity or chronic diseases. The aim of this study was to provide the first data on total fat, saturated fatty acids (SFA) and trans fatty acids (TFA) intakes and their major food sources in Tunisian children. A total of 1200 children, aged 3 to 9 years old (yo), were randomly selected from primary schools and kindergarten under a cross-sectional design. The 24-hour recall method and food frequency questionnaire were used to assess dietary intake. The energy percentages of total fat, SFA and TFA in Tunisian children were respectively 29.6, 11.4 and 0.15. No sex differences were found. The WHO recommendations for total fat, SFA and TFA were adopted by 58 %, 39 % and 89 % of the study population, respectively. The leading food groups of fat and fatty acids were ultra-processed foods, breakfast cereals and dairy products. The meat, fish, eggs and fish alternatives were the fifth main contributors to the total fat and SFA intakes in Tunisian children. The implementation of a relevant strategy for fat reduction, especially from ultra-processed foods, considered as low nutrient energy-dense products, is needed to promote health among children and prevent diet-related chronic diseases.

The liquid droplet cooling technique for fast scanning chip calorimetry (FSC) is introduced, increasing the cooling rate for large samples on a given sensor. Reaching higher cooling rates and using a gas as the cooling medium, the common standard for ultra-fast temperature control in cooling, requires reducing the lateral dimensions of the sample and sensor. The maximum cooling rate is limited by the heat capacity of the sample and the heat exchange between the gas and the sample. The enhanced cooling performance of the new liquid droplet cooling technique is demonstrated for both metals and polymers, on examples of solidification of large samples of indium, high-density polyethylene (HDPE), and poly (butylene 2,6-naphthalate) (PBN). It was found that the maximum cooling rate can be increased up to 5 MK/s in room temperature environment, that is, by 2 orders of magnitude, compared to standard gas cooling. Furthermore, modifying the droplet size and using coolants at different temperatures provide options to adjust the cooling rate in the temperature ranges of interest.

Body acceleration due the heartbeat-induced reaction forces can be measured as smartphone accelerometer (m-ACC) signals. Our aim was to test the feasibility of using m-ACC to detect changes induced by stress by ultra-short heart rate variability (USV) indices (SDNN and RMSSD). Sixteen healthy volunteers were recruited; m-ACC was recorded while in supine position, during spontaneous breathing (REST) and during one minute of mental stress (MS) induced by arithmetic serial subtraction task, simultaneous with conventional ECG. Beat occurrences were extracted from both ECG and m-ACC and used to compute USV indices using 60, 30 and 10s durations, both for REST and MS. A feasibility of 93.8% in the beat-to-beat m-ACC heart rate series extraction was reached. In both ECG and m-ACC series, compared to REST, in MS the mean beat duration was reduced by 15% and RMSSD decreased by 38%. These results show that short term recordings (up to 10 sec) of cardiac activity using smartphone’s accelerometers are able to capture the decrease in parasympathetic tone, in agreement with the induced stimulus.

The Pierre Auger Observatory is the world's largest operating detection system for the observation of ultra high energy cosmic rays (UHECRs). The detector allows detailed measurements of their energy spectrum, mass composition and arrival directions of primary cosmic rays in the energy range above $10^{17}$ eV. The data collected at the Observatory over the last decade show the suppression of the cosmic ray flux at energies above $4\times10^{19}$ eV. However, it is still unclear if this suppression is caused by the propagation of cosmic rays or rather by energy limitation of their sources. The other puzzle is the origin of UHECRs. Some clues can be drawn from studying the distribution of their arrival directions. The recently observed dipole anisotropy has an orientation which indicates an extragalactic origin of UHECRs. The Auger surface detector array is also sensitive to showers due to ultra high energy neutrinos of all flavours and photons, and recent neutrino and photon limits provided by the Observatory can constrain models of the cosmogenic neutrino production and exotic scenarios of the UHECRs origin, such as the decays of super heavy particles. In this paper the recent results on measurements of the energy spectrum, mass composition and arrival directions of cosmic rays, and future prospects are presented.

As a part of the proposed article, the authors presented comprehensive data analysis for movement data that comes from a positioning system based on ultra-wide band (UWB) technology. For purpose of this article, a test was carried out during which the car equipped with cruise control overcame the given path at a speed from 10 km/h to 60 km/h. The obtained motion models (information about position) have been filtered through a series of filters - from fundamentals filters with a variable window (median, moving average, Savitzky-Golay filter), through more complex ones like the Wiener or Kalman filter. As a result, the authors proposed a form of data analysis and filtration depending on the speed of the moving object. In addition, the maximum accuracy that can be obtained for a given traffic model was also determined. The whole research proves that it is possible to use a system based on UWB technology in positioning objects for urban applications - smart city, in industry 4.0 applications as well as for positioning autonomous vehicles in urban applications, such as well as on highways to maintain cohesion of convoys vehicles.

When an earthquake or a large fire has occurred, it is difficult to secure communication networks for rescue in the building due to the destruction of commercial communication networks. Although analog radio systems such as VHF (very high frequency) and UHF (ultra-high frequency) are used for rescue operation in general, communication failure occurs in closed spaces, causing difficulties in smooth rescue operations. When the communication infrastructures have been destroyed in a building in the disaster, an emergency wireless telecommunication environment should be constructed to secure a safer disaster response environment. In this study, along with comparison of the performances of diverse communication frequencies, UWB (Ultra-Wide Band) wireless telecommunication networks were evaluated under five building indoor environment conditions including open spaces. UWB communication modules were fabricated to satisfy the IEEE (The Institute of Electrical and Electronics Engineers) 802.15.4a standard performance to measure distances in which communications are possible according to the indoor environment for each of six channels with different UWB communication frequencies. The results indicated that the distances in which communications are possible for each the six channels were average 15.5 m, maximum 20 m in open spaces; average 17.33 m, maximum 20 m in corridors; average 15.3 m, maximum 20 m in indoor office environments with office fixtures; average 4.33 m, maximum 6 m in vertical spaces of stairs; and average 6.5 m, maximum 17 m in closed horizontal spaces with a fire door. In this case, the communication performance and distance performance were shown to be the most excellent at a frequency (Centre Frequency) of 6489.6 and a band of 5980.3 – 6998.9 MHz, which is UWB 7ch. In conclusion, it is judged that if UWB communication modules are installed in the disaster area at intervals of 20 m and multi-channels are used, communication environments can be constructed even in closed spaces

In small-scale hydropower scheme, the most important component is electro-mechanical equipment. Since cost contribution of this component is high because hydrokinetic projects require negligible civil works. Turbine and alternator contribute major fraction of the hydrokinetic projects. Thus, there is a requirement to estimates the electromechanical equipment cost for the hydrokinetic hydropower scheme. The present paper investigates design parameters of the hydrokinetic turbines and intends to develop cost correlation which depends on most critical parameters of hydropower sites such as velocity and power capacity. In this present work, three zero head turbines are considered including straight blade Darrieus, two Stage Savonius, and Gorlov Helical. The size and cost of major components have been calculated based on material, manufacturing, research and design, and assembly costs. Based on cost and site parameters, cost correlation has been developed. The obtained cost has been validated with available zero head turbines in the market and installed projects. A techno-economic analysis has been carried out to select economical hydrokinetic turbine for river and canal application.

CD4 count recovery is the main goal for an HIV patient who initiated ART. Some patients respond positively to ART and attain CD4 count recovery, some patients might fail to recover their CD4 count due to non-adherence, treatment resistance, and virological failure, leading to HIV-related complications and death. The purpose of this study is to find the determinants of death in patients who failed to recover their CD4 count after initiating antiretroviral therapy. The data used in this study was obtained from KwaZulu-Natal, South Africa, where 2528 HIV-infected patients with a baseline CD4 count of 200 cells/ were initiated on ART. We used a Fine-Gray sub-distribution hazard and cumulative incidence function to estimate potential confounding factors of death, where CD4 count recovery was a competing event for failure due to death. Patients who were not suffering from tuberculosis were 1.33 times at risk of dying before attaining CD4 count recovery [aSHR 1.33; 95% CI (0.96-1.85] compared to those who had no tuberculosis. Rural patients had a higher risk of not recovering and leading to death [aSHR 1.97; 95%CI (1.57-2.47)] than those from urban areas. The patient’s tuberculosis status, viral load, regimen, baseline CD4 count, and location were significant contributors to death before CD4 count recovery. Intervention programs targeting HIV testing in rural areas for early ART initiation and promoting treatment adherence are recommended.

Self-compacting concrete (SCC) is a high-quality construction solution combining high fluidity, passing and filling ability with improved mechanical properties and durability. In the present study, the effect of incorporating alternative waste materials, such as two by-products of the ce-ment industry, namely cement kiln dust (CKD) and by-pass dust (BPD), into SCC as partial re-placement for traditional filler material was investigated. The produced compositions were compared with reference mixtures containing only marble powder (MP) as a filler. A series of tests including specific test methods for wet SCC, compressive, flexural and tensile splitting strength tests as well as drying shrinkage determination were conducted to evaluate the quality of the produced SCC in terms of fresh and hardened SCC properties. The use of alternative fine filler materials resulted in a high-performance sustainable SCC of low cement content. Specifi-cally, incorporating CKD into the SCC enhanced its rheological behavior and improved slightly its mechanical properties, while the use of BPD led to SCC mixtures of adequate rheological characteristics but with highly upgraded mechanical and physical properties

Drought poses a significant constraint on rice production, and in this study, we have discovered a novel drought-sensitive mutant, designated as dsm3, arising from the progenies of indica rice variety Zhonghui8015 treated with EMS. Under drought stress conditions, dsm3 exhibited characteristic withered leaf tips, accompanied by increased levels of MDA and H2O2, reduced Pn, and decreased activity of POD and SOD. Genetic analysis revealed that the withered leaf tip phenotype was governed by a single recessive gene, designated as Osdsm3.To begin with, Osdsm3 was initially mapped to the short arm of chromosome 1 through a cross involving dsm3 and 02428. Subsequently, utilizing a population of 2591 F2 individuals, we narrowed down the location of Osdsm3 to a 78Kb interval, encompassing 13 open reading frames (ORFs). Sequencing analysis unveiled a mutation (1275G→A) in the exon of the candidate gene (LOC_Os01g10680), leading to premature translation termination. Moreover, a quantitative RT-PCR assay demonstrated high expression of OsDSM3 in the panicle and sheath, with a significant upregulation of drought stress-related genes under drought conditions. Phylogenetic analyses indicated that Osdsm3 shares evolutionary homology with UNE1, an intracellular transport protein found in Arabidopsis thaliana. Subcellular studies further confirmed that OsDSM3 resides in the cytoplasm. In conclusion, the forthcoming cloning of Osdsm3 holds promise for delving deeper into the molecular mechanisms governing rice drought resistance.

Air pollution is a leading cause of death in the United States, and is associated with adverse health outcomes, including increased vulnerability to coronavirus disease 2019 (COVID-19). The AirBeam2 was used to measure particulate matter with a diameter of 2.5 micrometers or smaller (PM2.5), to investigate differences between indoor and ambient levels at seven private homes in New York during and after the COVID-19 lockdown. Measurements taken in 2020 winter, spring and fall and in fall 2022 showed that 90% of the time, indoor PM2.5 levels exceeded outdoor levels both during and after the COVID-19 lockdown, p = 0.03, and exceeded safety levels. Higher indoor PM2.5 levels attributed to little or no ventilation from cooking and smoke in the kitchen and basements, were significantly greater in fall than in winter. Higher ambient PM2.5 levels were attributed to vehicular traffic at a street-facing sampling site. PM2.5 sources identified in this study may help in devising control strategies to improve indoor air quality (IAQ), and consequently alleviate respiratory health effects. These findings may be used as a basis for in-house modifications including natural ventilation and use of air purifiers to reduce exposures, mitigate future risks, and prevent potential harm to vulnerable residents.

The cast grains of the 7055 aluminum alloy were refined by adding Sm + Er, and the proper heat treatment procedure was utilized to further precipitate the rare earth phase in order to increase the alloy's strength and toughness. The grain size, microstructure and phase were characterized by optical microscopes (OM), Scanning electron microscopy - energy spectrum (SEM-EDS), XRD diffractometer (XRD). The macroscopic hardness, yield strength and tensile strength of alloy materials were measured by hardness meter and universal electronic tensile machine. The results shown that the as-cast sample and the heat treatment sample all exist Al10Cu7Sm2 and Al8Cu4Er rare earth phase; But after heat treatment, the volume percentage of the rare earth phase dramatically increased and the dispersion was more unified. When 0.3wt.%Sm and 0.1wt.%Er were added, the grain size could be refined to 53μm. With the increase of the total content of rare earth elements, the refining effect first increased and then decreased. Under 410 oC solid solution for 2h + 150oC aging for 12h, the macroscopic hardness, yield strength, tensile strength and elongation of 0.3wt.%Sm + 0.1wt.%Er+7055 as-cast sample were 155.8HV, 620.5Mpa, 658.1Mpa, and 11.90%, respectively.

Imaginary dimensions in physics require an imaginary set of base Planck units and some negative parameter $c_n$ corresponding to the speed of light in vacuum $c$. The second, negative fine-structure constant $\alpha_2^{-1} \approx -140.178$ present in Fresnel coefficients for the normal incidence of electromagnetic radiation on monolayer graphene leads to the imaginary Planck units. Furthermore, it sets $c_n \approx -3.06 \times 10^8~\text{[m/s]}$. It follows that electric charges are the same in real and imaginary dimensions. Neutron stars and white dwarfs, objects emitting perfect black-body radiation, need energy exceeding their mass-energy equivalence ratios. Complex energies are defined in terms of real and imaginary Planck units. Their imaginary parts, inaccessible for direct observation, store the excess of these energies. It follows that black holes are fundamentally uncharged, charged micro neutron stars and white dwarfs with masses lower than $5.7275 \times 10^{-10}~[\text{kg}]$ are unphysical, and the radii of white dwarfs' cores are limited to $R_{\text{WD}} < 6.7933~G M_{\text{WD}}/c^2$. It is conjectured that the maximum atomic number $Z=238$. A black-body object is in the equilibrium of complex energies of masses, charges, and wavelengths if its radius $R_\text{eq} \approx 2.7665~G M_{\text{BBO}}/c^2$, which corrects the value of the photon sphere radius $R_{\text{ps}}=3G M/c^2$, taking into account the value(s) of the fine-structure constant(s), which is otherwise neglected in general relativity.

Herein is introduced a simple scalar field model derived from classical based kinetic energy, gravitational potential energy, and Special Relativity’s rest mass energy. By applying a classical orbit over the scalar field, relativistic effects are predicted. The scalar field is then applied to a classical model of the Hydrogen atom resulting in a relativistic effect equal to the binding energy of the Hydrogen atom. In addition, the model derives the fine structure constant due to the gravitational effect. The relativistic effects are then discretized in increments equal to the model’s gravitational induced constant. The discretization produces the Hydrogen atom spectral emissions and an angular moment equal to Planck’s reduced constant. The model is not presented as a replacement for current theory, rather it is for inspection and illustration of how a simplistic model may offer a fundamental bridge between the more complex, time proven theories of General Relativity and Quantum Mechanics.

A geometric Planck-scale model of quantum electrodynamics is tested against observations. Based on Dirac’s proposal to describe spin 1/2 particles as tethered objects, elementary fermions are conjectured to be fluctuating rational tangles with unobservable tethers. As Battey-Pratt and Racey showed, when such tangles propagate, they obey the free Dirac equation. Classifying rational tangles yields the observed spectrum of elementary fermions. Classifying deformations of tangle cores yields exactly three types of gauge interactions. They exchange three types of elementary gauge bosons and have the symmetry groups U(1), broken SU(2) and SU(3). The possible rational tangles for fermions, Higgs and gauge bosons allow only the observed Feynman diagrams. The complete Lagrangian of the standard model arises, including the Lagrangian of quantum electrodynamics. Over 50 tests of the tangle model are deduced. They include details on the perturbation expansion of the g-factor and the existence of limit values for electric and magnetic fields. Measurements agree with most tests, though this could change in the future. Some tests are genuine predictions that still need to be checked. In particular, the geometry of the process occurring at QED interaction vertices suggests an ab-initio estimate for the fine structure constant. In addition, the average geometric shapes of the elementary particle tangles suggest ab-initio lower and upper limits for the mass values of the electron and the other leptons.

We have recently proposed a pre-quantum, pre-space-time theory as a matrix-valued Lagrangian dynamics on an octonionic space-time. This pre-theory offers the prospect of unifying the internal symmetries of the standard model with gravity. It can also predict the values of free parameters of the standard model, because these parameters arising in the Lagrangian are related to the algebra of the octonions which define the underlying non-commutative space-time on which the dynamical degrees of freedom evolve. These free parameters are related to the algebra $J_3(\mathbb O)$ [exceptional Jordan algebra] which in turn is related to the three fermion generations. The exceptional Jordan algebra [also known as the Albert algebra] is the finite dimensional algebra of 3x3 Hermitean matrices with octonionic entries. Its automorphism group is the exceptional Lie group $F_4$. These matrices admit a cubic characteristic equation whose eigenvalues are real and depend on the invariant trace, determinant, and an inner product made from the Jordan matrix. Also, there is some evidence in the literature that the groups $F_4$ and $E_6$ could play a role in the unification of the standard model symmetries, including the Lorentz symmetry. The octonion algebra is known to correctly yield the electric charge values (0, 1/3, 2/3, 1) for standard model fermions, via the eigenvalues of a $U(1)$ number operator, identified with $U(1)_{em}$. In the present article, we use the same octonionic representation of the fermions to compute the eigenvalues of the characteristic equation of the Albert algebra, and compare the resulting eigenvalues with the known mass ratios for quarks and leptons. We find that the ratios of the eigenvalues correctly reproduce the [square root of the] known mass ratios for quarks and charged leptons. We also propose a diagrammatic representation of the standard model bosons, Higgs and three fermion generations, in terms of the octonions, exhibiting an $F_4$ and $E_6$ symmetry. In conjunction with the trace dynamics Lagrangian, the Jordan eigenvalues also provide a first principles theoretical derivation of the low energy value of the fine structure constant, yielding the value $1/137.04006$. The Karolyhazy correction to this value gives an exact match with the measured value of the constant, after assuming a specific value for the electro-weak symmetry breaking energy scale.

Stable isotope concentrations in the soil, rain and ground water have been used to trace the water extraction zones of plants in different environments. The need to identify the plant water use by plants in afforestation programs to control desertification increases the importance of sap water partitioning of plants in sand dune areas. However, the introduction of new plant covers exerts pressure on the water resources and can affect the local soil water conditions. In this study, we analyzed the isotope concentrations in rain, soil, sap, and ground water after the summer of 2010. Two experimental plots established in the Hailiutu catchment (Shaanxi province, northwest China) were selected to gather the water samples between September and October 2010. One plot is dominated by Salix bushes (Salix psammophila C. Wang \& Chang Y. Yang) and the other by the tree species Willow (Salix matsudana Koidz.). The total precipitation at the experimental site was 401 mm/yr during 2010, while 88.7 mm was collected in total for the period September to October. Willow trees transpired 12.82 kg/d being almost three times larger than Salix shrubs (4.57 kg/d). Despite the transpiration rates of both plant species and the few rain events in the region, the soil water beneath the plant covers is not depleted. Stable isotope signature of soil water beneath both covers shows the fractionation front in Salix at 20 cm depth and at Willow at 40 cm depth. However, soil water signature is closer to the groundwater than the collected rain water.

The generation of high-quality wideband frequency sweeps presents a significant challenge, particularly in modern telecommunication, radar, and measurement systems where miniaturization is paramount. While phase-locked loops (PLLs) have become the dominant technique for signal generation, their application in broadband sweeps necessitates fractional-N operation. This, in turn, degrades phase noise and introduces unwanted spurs. This paper proposes a novel approach for broadband signal generation. By cascading two PLLs and utilizing a coaxial resonator, we achieve a high-performance oscillator that operates without the excessive fractional spurs, maintaining their level below -80 dBc across the entire frequency band. The prototype demonstrates non-degraded phase noise performance, reaching -102 dBc/Hz at 100 kHz offset and -121 dBc/Hz at 1 MHz offset for signal at 10 GHz. Despite significant frequency jumps, our design achieves lock times below 41 µs. These results, supported by theoretical analysis, validate the proposed method's effectiveness in generating low-noise broadband frequency sweeps, ideal for local oscillator applications.

In the autonomous navigation of mobile robots, precise positioning is crucial. In forest environments with weak satellite signals or in sites disturbed by complex environments, satellite positioning accuracy has difficulty in meeting the requirements of autonomous navigation positioning accuracy for robots. This article proposes a binocular vision SLAM/UWB tightly coupled localization method. The core of this algorithm is based on an Extended Kalman Filter (EKF), which utilizes the displacement increment output by binocular vision ORB-SLAM and the positioning coordinates calculated via UWB positioning as measurement information to achieve data fusion. The research utilized the constructed experimental platform to collect images and UWB ranging data in outdoor environments and experimentally validated the combined positioning method. The experimental results show that this algorithm outperforms the use of the individual UWB or visual SLAM localization methods in terms of positioning accuracy. Compared with traditional single positioning algorithms, this algorithm exhibits better practicality and stability, and can effectively suppress the impact of UWB non line of sight errors. The average error under normal line of sight conditions is 0.058 m, the root mean square error (RMSE) is 0.080, and the average error under non-line-of-sight conditions is 0.081 m, with an RMSE of 0.084. There is no significant jump or drift. Through the tightly coupled processing of binocular vision SLAM and UWB positioning, more reliable and accurate mobile robot positioning can be achieved, providing a useful reference for the autonomous navigation of mobile robots in complex environments.

Breakage and damage of fiber optic cable fibers seriously affect the normal operation of fiber optic networks and it is important to quickly and accurately determine the type and location of faults when they occur. The advantages of wavelet transform in singular signal detection and signal filtering are used to analyze Optical Time Domain Reflectometer (OTDR) curve signal and the fault detection method of fiber communication link with no relay and large span in high altitude area is given, which realizes the accurate detection and location of optical fiber communication link fault events under strong noise. The theoretical analysis is basically consistent with the experimental data. The accuracy of optical fiber fault location has been greatly improved in performance. The method has been directly applied to the field detection of ultra-long optical fiber links in high altitude areas, which has certain significance for the future real-time monitoring of optical fiber cables.

DEXTER (Detection of EXplosives and firearms to counter TERrorism) is a project funded by NATO’s Science for Peace and Security (SPS) program with the goal of developing an integrated system capable of remotely and accurately detecting explosives and firearms in public places without impeding the flow of pedestrians. The active microwave component of the DEXTER project is referred to as MIC (Microwave Imaging Curtain), supported by the French SGDSN (General Secretariat of Defense and National Security), and utilizes a radar system capable of generating 3D images in real time to address non-checkpoint detection of explosives and fire-arms. The project, led by the ONERA (France), is based on a radar imaging system developed by the Fraunhofer FHR institute, using a MIMO architecture with an Ultra Wide-Band waveform. Although high-resolution 3D microwave imaging is already being used in expensive body scanners to detect firearms concealed under clothing, MIC's innovative approach lies in utilizing a high-resolution 3D imaging device that can detect larger dangerous objects carried by moving individuals at a longer range, in addition to providing discrete detection in pedestrian flow. Automatic detection and classification of these dangerous objects is carried out on 3D radar im-ages using a deep-learning network. This paper will outline the project's objectives and constraints, as well as the design, architecture, and performance of the final system. Additionally, it will present real-time imaging results ob-tained during a live demonstration in a relevant environment.

Fleets of drones have attracted a lot of attention from the research community in recent years. One of the biggest challenges in deploying such systems is localization. While GNSS localization systems can only be effective in open outdoor environments, new solutions based on radio sensors (e.g., ultra-wideband) are increasingly being used for localization in various situations and environments. However, self-localization without prior knowledge of anchor positions remains an open problem which, for example, makes it impossible to track a moving target. In this article, we provide a comparison of different variants of gradient descent-based algorithms, with a new improved variant, for solving the localization problem using relative distance measurements and multilateration. It is applied to self-localization of anchors and tracking targets using ultra-wideband distance sensors. A realistic simulation of drone tracking and anchors’ localization is performed to demonstrate the robustness and accuracy of the proposed approach.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Under the big unified framework of quantum gravitational field and quantum repulsive field, the earlier in this series of work has comprehensively expanded the general relativity and loop quantum ring gravitation theory, set up the quantum repulsive field equation corresponding to the quantum gravitational field equation, and then established the quantum hedge-unified field equation describing the interaction of quantum gravitational field and quantum repulsive field; On this basis, the quantum repulsive universe equation corresponding to the quantum gravitational universe equation has be established, thus a set of new equations describing the expansive universe model under the condition of fully considering the hedge effect of quantum gravitational field and quantum repulsion field, which can be called the expansive universe equation of quantum hedge-unified field theory, has be established. Now, let's go deep into the arche-unified physics behind the creation of the universe. Although all kinds of inflationary universe models can solve cosmological problems to a certain extent, there is no natural and reasonable analysis and explanation for all cosmological and physical consequences. For example, it is impossible to predict a large tensor-scale ratio and a relatively large spectral index run at the same time. At present, string theory, membrane theory, loop quantum gravity theory, super-gravitational holography principle and M theory, which are the theoretical basis of cosmology, are basically established by simplification in the case of breaking away from the extreme background conditions of the universe. While cosmology, which is deficient in nature, cannot provide strong support for particle physics to further advance to a wider field and a deeper level. Due to the lack of new ideas, the construction of existing theoretical models is difficult. Therefore, the existing research can only be further promoted by new astronomical observation. Unlike existing studies, we concentrate on the emergence of the big rip-rebound clusters of quantum chaotic-reticulate distribution between the outwards-push of the universe as a whole (related to pseudo-vacuum energy, Higgs field, dark energy, etc.) and the inwards-pull of the universe in local scale (related to dark matter, quantum gravity and initial gravity separated from high-dimensional supergravity, and the initial strong force separated from the grand unified force subsequently). On the one hand, we find a great impetus to make the inflation of the universe into firstly-imposed suppression, then-imposed acceleration and finally-imposed deceleration, which really explains why the universe expands at a critical rate and has the same temperature in different regions, on the other hand, we find a fundamental unit of matter and its emerging clusters evolving in the big bang, inflation and expansion of the universe accompanied by the great rip-rebound clusters of quantum chaos-reticulate distribution, which can be reduced to an arche-pulsator of neither punctiform particle nor linear string. From these two aspects, it can been seen that the evolution of the early universe is much more complicated than people originally thought. The complexity of the super inflation of the universe is mainly reflected in the big rip-rebound cluster emerging behind the gravitational disturbance (the pressure and tensor disturbance related to dark matter), the repulsive disturbance (the pressure and scalar disturbance related to dark energy), the cosmological disturbance (related to the interaction between high-dimensional supergravity and high-dimensional superrepulsion). This is a system of nonlinear stochastic differential dynamics, or a quantum statistical physical process of nonlinear nonequilibrium state. In the new research paradigms established in this series, the arche-conjugation between the high-dimensional supergravity and the high-dimensional superrepulsion, as well as between the quantum gravity and the quantum repulsion, is higher than the supersymmetry, and then becomes the core concept of the new theory. In this series, cluster-inflating configuration, spin network space and cosmic paradigm vectors are proposed, so the model of the super-inflated universe with quantum chaos-reticulate distribution emerged under the great impetus. The new model reveals that the unified inflation of the universe as a whole and the local inflation of the universe emerge together in the great impetus of the big rip-rebound cluster of quantum chaos-reticulate distribution. As a spin network model variable, the spatiotemporal mode variable is a vector composed of a series of variables, which variables include: dimension, curvature, range, expansion speed, dynamics, quantization, chaotic-reticulate distribution (inhomogeneity, concentration, fluctuation), synergy, and so on. Between particle physics and cosmology, this series of papers proposes the cosmic quantum evolution mode, the physical-sphere distributing configuration and the interaction situation variables, organizes the concepts, variables and models of these three levels, and establishes a systematic super-synergy paradigm. In this paradigm, the general Langevan equation and the general Fokker-Planck equation are established. For the quantum cosmic-sphere, a series of trend parameters are introduced to establish the dynamics of quantum gravitational mode and its master equation, and then to establish the operator distribution function and its motion equation of the action mode. For the Tachyon of upheaval in the rip-rebound-inflating of the universe, the hypothesis on the bifurcate-chaos wave of quantum is given, the quantum theory of the early photons in upheaval is set up, and the analysis on the particles of the ultrahigh energy cosmic ray from the γ ray burst is made. Finally, using Wigner-Ville distribution as a nonlinear time-frequency distribution, we establish the ultra-synergistic field equation of quantum-classic unifying action-sphere.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

Ultra-weak photon emissions (UPEs) including those from human have been experimented for decades. The photo-genic origin of UPE has also been attributed to the oxidative stress or free radical production that is unique to metabolically active states of biological organisms. However, there are considerable gaps in quantitative understanding of UPE. In this work, I propose an analytical framework of hypothesis for the initial objective of modeling a few superficial presentations of UPE of human, including the systematic dependency on age, the diurnal variation, and the geometric asymmetry associated with serious asymmetrical pathological conditions. The hypothesis which is currently limited to human assumes a new form of energy state, termed vivo-nergy, which resides only in metabolically active organisms that are also under neuronal control. The hypothesis projects a decrease of the vivo-nergy in human during growth beyond puberty, with the rate of decrease dictated by a critical time-scale---the age of the first opposite-sex sexual intercourse (FOSSI). The hypothesis also proposes a modification of the vivo-nergy by the phases of systematic or homeostatic physiology. The hypothesis further postulates that the deviation of the physiology-modified vivo-nergy from the pre-puberty level is deteriorated by acquired organ-specific pathological conditions. Any reduction of vivo-nergy from the pre-puberty level is hypothesized to proportionally cause oxidative stress that functions as the physical source of UPE. The resulted steady-state diffusion of the photon emitted from a photo-genic source of UPE in a human geometry simplified as a homogeneous spherical domain is modeled by photon diffusion principles incorporating an extrapolated zero-boundary condition. The age and systematic physiology combined determines the intensity of the centered physiological photo-genic source. The acquired (single) pathology sets both the intensity and the off-center position of the (single) pathological photo-genic source. When the age-related, physiology-commanded, and pathology-controlled modifications of the photo-genetic sources are implemented in the photon diffusion model, the photon fluence rate at the surface of the simplified human-representing spherical domain reveals the dependency on age, the temporal variation corresponding to systematic physiology, and the geometric asymmetry associated with significant asymmetric pathological condition as reported previously for UPE. The hypothesis, as it provides analytical conveniences for quantitative estimation of UPE patterns, may be useful to further model-based interpretation of the spatial-temporal characteristics of UPE.

The VLSI industry is facing parasitic effects that trouble development in the nanoscale domain. However, instead of replacing the traditional MOSFET design, it would be more advantageous to apply different doping profiles and discerning which deal with specific parasitic effects the best. With a review of Gaussian doping, Uniform doping, and Delta doping profiles and analysis of the FET technology characteristics that use these doping profiles, a comparison can be made among them for integrated circuit design engineers. These doping profiles are compared based on how well they perform against non-ideal and ideal environments. Also, both digital and analog performance are measured to ensure the uniqueness of each doping profile that is present. After getting a list of benefits from each doping profile, it is derived to determine which doping profile works best against a host of parasitic effects and what type of application do these doping profiles have

The high prevalence of thyroid nodules and increased availability of neck ultrasound have led to an increased incidence of diagnostic thyroid fine needle aspirations, with approximately 20% yielding indeterminate results. The recent availability of molecular tests has helped guide the clinical management of these cases. This paper aims to review and compare three main commercially available molecular cytology platforms in the U.S. – Afirma GSC, Thyroseq GC, and ThyGeNEXT+ThyraMIR. Sequential improvements of the Afirma GSC and Thyroseq GC tests have led to higher positive and negative predictive values, sensitivity, and specificity. Comparative studies revealed similar diagnostic performance between these tests, with considerations for factors such as cost and processing time. Thyroseq GC provides detailed genomic information and specific management recommendations. ThyGeNEXT+ThyraMIR, though less studied, presents promising results, particularly in miRNA analysis for weak driver mutations. Challenges in interpreting results include variations in reporting and the evolving nature of testing platforms. Questions persist regarding cost-effectiveness and the utility of ultrasound characteristics in selecting candidates for molecular testing. While molecular testing has primarily served diagnostic purposes, advancements in understanding genetic alterations now offer therapeutic implications. FDA-approved options target specific genetic alterations, signaling a promising future for tailored treatments.

The characteristics of response to stressful situations depend on a complex of factors such as personality traits, emotional regulation, health state, features of the nervous system, motor functions and proprioception. In cases of disruption of the brain's dopamine system due to disease or chemotherapy, hormone discharge due to stress, changes in emotions and proprioception may occur. The aim of our study was to find the relationship of stress resilence in verbal test and individual differences performed in proprioceptive test in onco-patients, sportsmen and group of control; as well as to observe the differences between these groups in the verbal stress resistance and individual differences proprioceptive tests. The results showed that onco-patients were less resistant as per verbal stress resistance outcomes for a major part of variables compared to other groups. The sportsmen were superior in verbal Risk and Control dimensions compared to other groups; but less in Positive Affectiveness. The proprioceptive test perfomance revealed the only statistically significant difference in performance in the dimension related to Mood, showing more Pessimism in the sportsmen group, but more Optimism in the oncopatients at temperamental (or intrisinc) level. The obtained results can be used by psychologists, therapists, coach and healthcare when needed to attend the specific needs of public, being pateints or sportsmen, etc.

Accurate and efficient medicinal plant image classification is of utmost importance as these plants produce a wide variety of bioactive compounds that offer therapeutic benefits. With a long history of medicinal plant usage, different parts of plants, such as flowers, leaves, and roots, have been recognized for their medicinal properties and are used for plant identification. However, leaf images are extensively used due to their convenient accessibility and are a major source of information. In recent years, transfer learning and fine-tuning, which use pre-trained deep convolutional networks to extract pertinent features, has emerged as an extremely effective approach for image identification problems. This study is leveraging the power of three component deep convolutional neural networks, namely VGG16, VGG19 and DenseNet201, to derive features from the input images of the medicinal plant dataset, containing leaf images of 30 classes. The models were compared and ensembled to make four hybrid models to enhance the predictive performance by utilizing the averaging and weighted averaging strategies. Quantitative experiments were carried out to evaluate the models on the Mendeley medicinal leaf dataset. The resultant ensemble of VGG19+DensNet201 with fine-tuning showcases enhanced capability in identifying medicinal plant images with an improvement of 7.43% and 5.8% compared with VGG19 and VGG16. Furthermore, VGG19+DensNet201 can outperform its standalone counterparts by achieving an accuracy of 99.12% on the test set. A thorough assessment with metrics such as accuracy, recall, precision, and f1-score firmly establishes the effectiveness of the ensemble strategy.

Deep neural network (DNN) watermarking is a potential approach for protecting the intellectual property rights of DNN models. Similar to classical watermarking techniques for multimedia content, the requirements for DNN watermarking include capacity, robustness, and transparency, and other factors. Studies have focused on robustness against retraining and fine-tuning. However, less important neurons in the DNN model may be pruned. Moreover, although the encoding approach in renders DNN watermarking robust against pruning attacks, the watermark is assumed to be embedded only into the fully connected layer in the fine-tuning model. In this study, we extended the method such that the model can be applied to any convolution layer of the DNN model and designed a watermark detector based on a statistical analysis of the extracted weight parameters to evaluate whether the model is watermarked. Using a nonfungible token mitigates the overwriting of the watermark and enables checking when the DNN model with the watermark was created.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

This paper presents a study of an automated system for identifying planktic foraminifera at the species level. The system uses a combination of deep learning methods, specifically Convolutional Neural Networks (CNNs), to analyze digital images of foraminifera taken at different illumination angles. The dataset is composed of 1437 groups of sixteen grayscale images, one group for each foraminifer, that are then converted to RGB images with various processing methods. These RGB images are fed into a set of CNNs, organized in an Ensemble Learning (EL) environment. The ensemble is built by training different networks using different approaches for creating the RGB images. The study finds that an ensemble of CNN models trained on different RGB images improves the system's performance compared to other state-of-the-art approaches. The proposed system was also found to outperform human experts in classification accuracy.

Glacier dynamics play an important role in the mass balance of many glaciers, ice caps and ice sheets. In this study we exploit Radarsat-2 (RS-2) Wide Fine (WF) data to determine the surface speed of Svalbard glaciers in the winters of 2012/2013 and 2013/2014 using Synthetic Aperture RADAR (SAR) offset and speckle tracking. The RS-2 WF mode combines the advantages of the large spatial coverage of the Wide mode (150 x 150 km) and the high pixel resolution (9m) of the Fine mode and thus has a major potential for glacier velocity monitoring from space through offset and speckle tracking. Faster flowing glaciers (1.95 m d^-1 - 2.55 m d^-1) which are studied in detail are Nathorstbreen, Kronebreen, Kongsbreen and Monacobreen. Using our Radarsat-2 WF dataset, we compare the performance of two SAR tracking algorithms, namely the GAMMA Remote Sensing Software and a custom written MATLAB script (GRAY method) that has primarily been used in the Canadian Arctic. Both algorithms provide comparable results, especially for the faster flowing glaciers and the termini of slower tidewater glaciers. A comparison of the WF data to RS-2 Ultrafine and Wide mode data reveals the superiority of RS-2 WF data over the Wide mode data.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

Carbon nanomaterial is widely used in structural health monitoring due to the advantage of sensitivity and good mechanical properties. This study presents a novel approach employing carbon nanocomposite materials (CNM) to characterize deformation and damage evolution in physical modelling. As the primary measurement method, the CNM is used to investigate the deformation characteristics of a 200-400 m thick sandstone bed at a 1 km deep longwall mine. The sandstone unit is identified as an ultra-thick key stratum (UTKS), with its thicknesses varying across different mining panels of the UTKS. The results of CNM monitoring show that the UTKS remains stable even after a consecutive excavation of 900 m in width. This stability impedes the upward propagation of overlying strata failure, leading to minimal surface subsidence. The study demonstrates the huge potential of CNM in the mining area, which can be useful for investigating material damage in physical modelling studies. The findings suggest that the cumulative extraction width in individual mining areas of the mine should be controlled to avoid a sudden collapse of the UTKS, and that special attention should be paid to where the UTKS's thickness changes substantially. The substantial variation in UTKS thickness significantly impacts the pattern of overburden subsidence.