This work aims to explore the impact of side loads, drill-pipe tool-joint (DP-TJ) speed (RPM), and mud type on the austenitic stainless steel SM2535-110 casing wear characteristics. Actual field drill pipe tool joints, casings, and drilling muds are used in this study. The results of the study show that under both types of lubrication, the wear volume increased with radial load and DP-TJ speed. SM2535-110 casing specimens tested under oil-based mud (OBM) lubrication had higher casing wear volumes than those obtained under water-based mud (WBM) lubrication. This unexpected behavior is mainly due to the increase in the surface hardness of the casing specimens tested under WBM. The results also show that the specific wear factor (K) values of specimens tested under WBM are in general 2 to 4 times higher than those obtained under OBM. While K values under WBM increase with both the side load and RPM, those under OBM show a sharp decrease with RPM. This behavior under OBM is due to this lubricant’s higher viscosity and the change of lubrication regime from thin film to thick film lubrication at higher RPM. Scanning electron microscopy (SEM) and the digital microscopic imaging (DMI) of SM235-110 casing specimens show that an aggressive combination of adhesive, abrasive, and plastic deformation was observed under WBM, while the dominant wear mechanism under OBM is abrasive wear.

This study compares the effects of lecture-based instruction and process-oriented guided inquiry learning (POGIL)-based instruction on the self-efficacy performance of Grade 12 students. A quasi-experimental, pretest-posttest design was adopted to investigate and assess the impact of POGIL-based instruction versus lecture-based instruction on students’ performance as measured by three types of cognitive outcomes; Knowing, Applying and Reasoning (KAR). Two government high schools in Alain were selected as research sites, one for the boys and one for the girls. The total number of participants was approximately 110 students (N=110); 54 were assigned to treatment groups (25 girls and 29 boys), and 56 were assigned to control groups (27 girls and 29 boys). The treatment group was taught a circular motion unit in physics using POGIL-based instruction, while the control group was taught the unit using lecture-based instruction. The study's findings showed statistically significant differences between students of the control group and the treatment group in favour of the latter regarding their science performance, self-efficacy and science-related attitudes. Moreover, positive correlations were found between participants’ performance at the KAR test, self-efficacy and scientific attitudes towards scientific inquiry after the intervention. In conclusion, it is recommended to shift teaching towards POGIL-based instruction due to its positive impact on students’ performance and self-efficacy. It is also suggested to replicate the study to include government and private schools, elementary and high schools, teachers and advisors.

The paper proposes a rock classification method using the vibration signal of the rotary drilling process. This proposed method classifies four rocks with a reliability of 100 %, from the vibration signal record of a lasting 1/4 second. For the design of a suitable classification method, several attributes of the vibration signal were calculated for two different signal recording lengths. Cluster dendrogram, ANOVA test, and boxplot were used to determine useful attributes and proper signal length. The classification rule was found using a decision tree, machine learning tool. The publication gradually describes the process of creating the classification method and the results of the reliability verification of the proposed classification method. Rock disintegration by rotary drilling was carried out under standardized experimental conditions. The disintegration rocks were andesite, granite, limestone, and concrete.

Conservation of tropical endemic amphibians largely suffers from Wallacean shortfall, a gap to which predictive species distribution models have contributed significantly to bridge by delineating probable distribution and the underlying suitable habitat within their distributional range. However, rarely is a prediction model ground-truthed to evaluate their predictive performance. Here we present a species distribution modeling approach using maximum entropy algorithm corrected for smaller sample size, in guiding explorative surveys aimed at optimizing survey effort and discovering unrecorded populations of Zhangixalus suffry, a rhacophorid tree-frog endemic to the northeastern part of the Indian subcontinent along with the factors limiting their distribution. With only 16 established historical locality data to model for (after spatial thinning to reduce autocorrelation) and a set of environmental predictors (climatic, topographic, and landscape composition), our model prediction enabled the successful discovery of seven new population records from unreported landscapes, extending its southernmost distributional limit over a considerable distance. The final composite distribution model combining all the locality records (n=23) predicted similar core areas of suitable habitat consistent with the known geographic distribution of the species but showed poor representation under existing coverage of Protected Area (PA) network in the Region with only 7% representation of suitable habitat under protection. Habitat suitability of a site was significantly governed by factors related to precipitation (precipitation seasonality and precipitation of the warmest quarter) and topographic factors that can influence it (elevation and aspect). This corroborates with the known ecology of Rhacophorid frogs, especially concerning their seasonal explosive reproductive strategy and foam nest-building behavior.Through this study, we propose explorative surveys guided by species distribution models to expedite unknown population discovery of rare, tropical endemic amphibians and using such taxa as surrogates in identifying conservation priority zones that can be directly applied to reserve design and conservation and management planning.

AbstractEliadean analysis reveals the passive or the receiving aspect of the symbol of the presence of God, the Aron ha-Berit or the Ark of the Covenant of the ancient Hebrews. Consequently, we are able to establish the inner mode or the symbolic structure of Yahweh. The Sefirotic Tree of medieval Kabbalists replicates the symbolic structure of Yahweh as revealed by the Ark of the Covenant. The feminine aspect of the presence of God remains in the consciousness of the Jewish people and blossoms in the medieval Kabbalah. It is precisely the feminine aspect that is capable of transcendence or able to acquire an infinite character.The dynamic aspect of the Shekhinah is reflective of the changes it undergoes as a result of receiving the flow from the Sefiroth above. Looking at the Sefirotic Tree as a reflection of the mind of the Kabbalist, Shekhinah represents the human ability for acceptance. A narrow acceptance corresponds to a narrow mind, whereas the infinite ability to accept corresponds to the infinite mind. A particular description of the formative function of Shekhinah represents a different mode of cognition. Similar descriptions are found in the Tibetan Buddhist tradition related to the concept of Rigpa. In order to find out the equivalence of these descriptions we analyzed the latter and found that Shekhinah and Rigpa converge at both the foundational and transcendental levels.

Oaks are a dominant and key tree species in Mediterranean forest ecosystems. However, in recent decades, oak forests have been heavily impacted by oak decline, a worldwide phenomenon exacerbated by climate change. The charcoal disease agent Biscogniauxia mediterranea is involved in the decline of Mediterranean oak formations in a variety of contexts. Here, we investigated the impact and role of B. mediterranea in decline of oaks in Castelfidardo Forest, a relict wood of the late Holocene and a Site of Community Importance. We established five plots within which we recorded the tree positions, any symptoms and signs of decline, association of B. mediterranea to declining trees, and the deadwood and associated mycota. Of 471 oaks inspected, 7.0% showed brownish exudates on the stems, 46.9% showed epicormic shoots along the main trunk, and 24.4% showed black carbonaceous stromata on diseased branches and trunks. The decline was most severe for Quercus cerris, which comprised plots #4 and #5, at 50.0% (81/162 trees) and 29.0% (33/114), respectively; then for Quercus robur for plot #3, at 40.0% (38/95); and finally for Quercus pubescens for plots #1 and #2, at 13.7% (7/51) and 12.3% (6/49), respectively. Bark tissue was collected from trees with charcoal cankers, with microscopy examination and identification by mycological and molecular methods. This investigation revealed close association between oaks with pronounced reduction of vitality and incidence of B. mediterranea. The deadwood was equally distributed among the five plots, and was heavily colonized by Basidiomycota. The high incidence of this oak-weakening pathogen B. mediterranea appears to be related to stress conditions (e.g., water scarcity, prolonged drought). However, absence of silvicultural management, high competition among physiologically mature trees, and the geographic isolation of this residual forest might have predisposed these oaks to decline.

Trees in residential landscapes provide many benefits, but can injure persons and damage property when they fail. In hurricane-prone regions like Florida, USA, the regular occurrence of hurricanes has provided an opportunity to assess factors that influence the likelihood of wind-induced tree failure and develop species failure profiles. We assessed open-grown trees in Naples, Florida, following the passage of Hurricane Irma in September 2017 to determine the effect of relevant factors on the degree of damage sustained by individual trees. Of 4,034 assessed individuals (n = 15 species), 74% sustained no damage, 4% sustained only minor damage (i.e., minimal corrective pruning needed), 6% sustained significant damage (i.e., major corrective pruning needed), and 15% were whole tree failures (i.e., overturned trees or trees requiring removal). The proportion of individuals in each damage category varied among species, stem diameter at 1.4 m above ground, and the presence of utility lines, which was a proxy for maintenance. We compared our results with the findings of seven previous hurricanes in the region to explore species’ resilience in hurricanes.

Interest in drone solutions in forestry applications is growing. Using drones, datasets can be captured flexibly and at high spatial and temporal resolutions when needed. In forestry applications, fundamental tasks include the detection of individual trees, tree species classification, bio-mass estimation, etc. Deep Neural Networks (DNN) have shown superior results when comparing with conventional machine learning methods such as Multi-Layer Perceptron (MLP) in cases of huge input data. The objective of this research was to investigate 3D convolutional neural networks (3D-CNN) to classify three major tree species in a boreal forest: pine, spruce, and birch. The proposed 3D-CNN models were employed to classify tree species in a test site in Finland. The classifiers were trained with a dataset of 3039 manually labelled trees. Then the accuracies were assessed by employing independent datasets of 803 records. To find the most efficient set of feature combination, we compare the performances of 3D-CNN models trained with hyperspectral (HS) channels, RGB channels, and canopy height model (CHM), separately and combined. It is demonstrated that the proposed 3D-CNN model with RGB and HS layers produces the highest classification accuracy. The producer accuracy of the best 3D-CNN classifier on the test dataset were 99.6%, 94.8%, and 97.4% for pines, spruces, and birches, respectively. The best 3D-CNN classifier produced ~5% better classification accuracy than the MLP with all layers. Our results suggest that the proposed method provides excellent classification results with acceptable performance metrics for HS datasets. Our results show that pine class was detectable in most layers. Spruce was most detectable in RGB data, while birch was most detectable in the HS layers. Furthermore, the RGB datasets provide acceptable results for many low-accuracy applications.

Adequate knowledge about the development and operation of the components of water systems is of high importance in order to optimize them. For this reason, forecasting of future events becomes greatly significant due to making the appropriate decision. Moreover, operational river management severely depends on accurate and reliable flow forecasts. In this regard, current study inspects the accuracy of support vector regression (SVR), and SVR regulated with fruit fly optimization algorithm (FOASVR) and M5 model tree (M5), in river flow forecasting. Monthly data of river flow in two stations of the Lake Urmia Basin (Vaniar and Babarud stations on the Aji Chay and the Barandouz Rivers) were utilized in the current research. Additionally, the influence of periodicity (π) on the forecasting enactment was examined. To assess the performance of mentioned models, different statistical meters were implemented, including root mean squared error (RMSE), mean absolute error (MAE), correlation coefficient (R), and Bayesian information criterion (BIC). Results showed that the FOASVR with RMSE (4.36 and 6.33 m3/s), MAE (2.40 and 3.71 m3/s) and R (0.82 and 0.81) values had the best performances in forecasting river flows in Babarud and Vaniar stations, respectively. Also, regarding BIC parameters, Q_t-1 and π were selected as parsimonious inputs for predicting river flow one month ahead. Overall findings indicated that, although both FOASVR and M5 predicted the river flows in suitable accordance with observed river flows, the performance of FOASVR was moderately better than the M5 and periodicity noticeably increased the performances of the models; consequently, FOASVR can be suggested as the accurate method for forecasting river flows.

Adequate knowledge about the development and operation of the components of water systems is of high importance in order to optimize them. For this reason, forecasting of future events becomes greatly significant due to making the appropriate decision. Moreover, operational river management severely depends on accurate and reliable flow forecasts. In this regard, current study inspects the accuracy of support vector regression (SVR), and SVR regulated with fruit fly optimization algorithm (FOASVR) and M5 model tree (M5), in river flow forecasting. Monthly data of river flow in two stations of the Lake Urmia Basin (Vaniar and Babarud stations on the Aji Chay and the Barandouz Rivers) were utilized in the current research. Additionally, the influence of periodicity (π) on the forecasting enactment was examined. To assess the performance of mentioned models, different statistical meters were implemented, including root mean squared error (RMSE), mean absolute error (MAE), correlation coefficient (R), and Bayesian information criterion (BIC). Results showed that the FOASVR with RMSE (4.36 and 6.33 m3/s), MAE (2.40 and 3.71 m3/s) and R (0.82 and 0.81) values had the best performances in forecasting river flows in Babarud and Vaniar stations, respectively. Also, regarding BIC parameters, Qt-1 and π were selected as parsimonious inputs for predicting river flow one month ahead. Overall findings indicated that, although both FOASVR and M5 predicted the river flows in suitable accordance with observed river flows, the performance of FOASVR was moderately better than the M5 and periodicity noticeably increased the performances of the models; consequently, FOASVR can be suggested as the accurate method for forecasting river flows.

Tree peony flowers are traditional ornamental and medicinal materials in China. In this study, 23 tree peony flowers at a broad color spectrum were analyzed. Gas chromatography-mass spectrometer (GC-MS) revealed that tree peony flowers are rich in sugars and organic acids. Up to 18 amino acids were identified by liquid chromatography-mass spectrometer (LC-MS), including all essential amino acids, except for methionine. The majority of amino acids were significant positively correlated with each other and were significant negatively correlated with glucose, fructose and galactose. A total of 11 polyphenols were identified in these tree fresh peony flowers by LC-MS. There was a high consistency in grouping peony flowers by using sugars and organic acids and amino acids, which differed from that based on color components and polyphenols. Tree peony flowers are also rich in K, Ca, Mg and Fe. In together, peony flowers can be a good resource of health-promoting compounds.

For the first time, We do fuzzification the concept of domination in crisp graph on a generalization of fuzzy graph by using membership values of vertices, α-strong edges and edges. In this paper, we introduce the first variation on the domination theme which we call vertex domination. We determine the vertex domination number γ_v for several classes of t-norm fuzzy graphs which include complete t-norm fuzzy graph, complete bipartite t-norm fuzzy graph, star t-norm fuzzy graph and empty t-norm fuzzy graph. The relationship between effective edges and α-strong edges is obtained. Finally, we discuss about vertex dominating set of a fuzzy tree with respect to a t-norm ⨂ by using the bridges and α-strong edges equivalence.

Human microbiome data from genomic sequencing technologies is fast accumulating, giving us insights into bacterial taxa that contribute to health and disease. Predictive modeling of such microbiota count data for classification of human infection from parasitic worms such as helminths can help in detection and management across global populations. Real-world datasets of microbiome experiments are typically sparse containing hundreds of measurements for bacterial species, of which only a few are detected in the bio-specimens that are analyzed. This feature of microbiome data produces the challenge of needing more observations for accurate predictive modeling and has been dealt with previously using different methods of feature reduction. To our knowledge, integrative methods such as transfer learning has not been explored in the microbiome domain yet, as a way to deal with data sparsity by incorporating knowledge of different but related datasets. One way of incorporating this knowledge is by using a meaningful mapping among features of these datasets. In this paper, we claim that this mapping would exist among members of each individual cluster grouped based on phylogenetic dependency among taxa and their association to the phenotype. We validate our claim by showing that models incorporating associations in such a grouped feature space result in no performance deterioration for the given classification task. In this paper, we test our hypothesis using classification models that detect helminth infection in microbiota of human fecal samples obtained from Indonesia and Liberia countries. In our experiments, we first learn binary classifiers for helminth infection detection by using Naive Bayes, Support Vector Machines, Multilayer Perceptrons, and Random Forest methods. In the next step, we add taxonomic modeling using the SMART-scan module to group the data, and learn classifiers using the same four methods, to test the validity of the achieved groupings. We observed a 6% to 23% and 7% to 26% performance improvement based on the Area Under ROC Curve (AUC) and Balanced Accuracy(Bacc) measures, respectively, over 10 runs of 10-fold cross-validation. These results show that using phylogenetic dependency for grouping our microbiota data actually results in a noticeable improvement in classification performance for helminth infection detection. These promising results from this feasibility study demonstrate that methods such as SMART-scan can be utilized in the future for knowledge transfer from different but related microbiome datasets by phylogenetically-related functional mapping, to enable novel integrative biomarker discovery.

Background: Endometriosis is a female chronic inflammatory disease in which endometrial tissue develops outside the uterine cavity. It is a complex pathology, that significantly contributes to morbidity in premenopausal women, leading to chronic pain, infertility, and subfertility negatively impacting the physical, and emotional well-being and overall quality of life. The public health burden of endometriosis remains elusive and challenging to determine, and this uncertainty can lead to inadequate healthcare services and treatments. Objective: To estimate the incidence and prevalence of endometriosis in Italy using the hospital discharge records database. Population-based retrospective study. Nationwide between 2011 and 2020. Methods: From the National Hospital Discharge Database were selected all admissions with a diagnosis of endometriosis (ICD-9-CM, codes 617.x), supported by the presence of a procedure code of laparoscopy or any other surgical procedure allowing direct visualisation of the lesions. Main outcomes measures Incidence and prevalence of endometriosis were estimated for the entire 2010-2020 period and by individual year, analysing the time trend and variability in different geographical areas of Italy. Results: A total of 134,667,646 women aged 15–50 years with one or more hospitalisations for endometriosis in all Italian hospitals. The incidence of endometriosis in Italy during this period was 0.839 per 1000 women (CI95% 0.834-0.844), exhibiting a statistically significant decreasing trend over the years. A discernible north-south gradient was observed, with higher rates documented in the northern regions. The prevalence rate stood at 14.0 per 1000 during the same period, and a similar north-south geographical gradient was identifiable in the prevalence rates as well. Conclusions: The utilization of national-level hospital data enables the generation of incidence and prevalence data for endometriosis without variations in methods and definitions, facilitating the evaluation of temporal trends and regional comparisons. Understanding and quantifying this phenomenon is essential for appropriate healthcare planning in various Italian regions.

The potential advantages of plant-based interventions in decreasing the incidence and lessening the morbidity and mortality of COVID-19 are yet to be widely acknowledged. Nevertheless, recent publications propose that these interventions could be effective. Our cardiology center conducted an interventional study in which we incorporated plant-based foods and provided supplementation to 3470 elderly COVID-19 patients with multiple comorbidities. We pay close attention to the precise selection of food items, the application of appropriate processing methods, and the provision of nourishing meals to our patients. Our outcome was highly successful as we achieved a zero mortality rate, and none of our patients experienced worsening conditions or required hospitalization. In this review article we present the mechanisms how plant-based and supplement interventions can mitigate COVID-19 disease severity and mortality. And experts have validated our hypotheses very recently. The measures and methods used to address the ongoing SARS-CoV-2 pandemic through plant-based interventions and supplements are effective and may help prevent or manage future pandemics.

Abstract: This study aims to evaluate the effectiveness of plant-based diets and supplement interventions in mitigating the severity and mortality of COVID-19 patients. Observational research suggests that a diet high in plant-based foods may decrease the likelihood and severity of SARS-CoV-2 infection. However, several studies have faced criticism regarding the accuracy of obtaining dietary questionnaires and the insufficient intake of essential vitamins and minerals in such diets. To address these issues, this study employed a prospective interventional design that strictly controlled the quality, quantity, and processing of plant-based foods provided. Furthermore, the study incorporated supplementation, which enhanced the anti-viral, anti-inflammatory, antioxidant, antithrombotic, and immunomodulatory properties of a plant-based diet against the SARS-CoV-2 virus. Of the 3,470 COVID-19 elderly patients, half already followed a plant-based diet, and the other half new patients, both with various comorbidities, were intervened with a plant-based diet and supplementation. The results showed that the participants in the non-plant-based diet group were twice as likely to have experienced moderate disease (with 95% confidence limit: 1.42-3.12) and 2.4 times more likely to have experienced severe disease (with 95% confidence limit: 1.2-5.0) with a significant p-value of less than 0.0005 and 0.016 respectively, compared to those in the PBD group. During the interventions, none of the participants experienced disease progression or hospitalization, and there were no reported deaths by the end of the study. The outcome was highly favorable and aligned with the researchers' expectations, as COVID-19 morbidity and mortality rates in Indonesia were among the highest in Asia. This research may provide significant insights into the prevention and management of COVID-19 and aid in better preparation for future pandemics.

Chitosan is a copolymer of β-glucosamine and N-acetylglucosamine. Recent experiments showed that the degree and pattern of acetylation along the chitosan chain modulate the biological and physicochemical properties; however, the molecular mechanism is unknown. Here we apply the de novo all-atom molecular dynamics (MD) simulations to study chitosan’s self-assembly process at different degrees of acetylation and two different acetylation patterns. The simulations revealed that the 10-mer chitosan chains with 50% acetylation in either block or alternating patterns associate to form ordered nanofibrils comprised of mainly antiparallel chains in agreement with the fiber diffraction data of deacetylated chitosan. Surprisingly, regardless of the acetylation pattern, the same intermolecular hydrogen bonds mediate the fibril sheet formation while water-mediated interactions stabilize the sheet-sheet stacking. Moreover, the acetylated units are involved in forming the strong intermolecular hydrogen bonds (NH–O6 and O6H–O7), which offers an explanation for the experimental observation that increased acetylation lowers chitosan’s solubility. Taken together, the present study provides the atomic-level understanding the role of acetylation plays in modulating chitosan’s physiochemical properties, contributing to the rational design of chitosan-based materials with the ability to tune by its degree and pattern of acetylation. Additionally, we disseminate the improved molecular mechanics parameters that can be applied in MD studies to further understand chitosan-based materials.

The process of Targeted Opinion Word Extraction (TOWE), a critical component of aspect-based sentiment analysis (ABSA), revolves around identifying opinionated words linked to specific aspect-terms within sentences. Existing deep learning approaches, while effective, often overlook the syntactic structure of sentences, a factor that previous studies have identified as beneficial for TOWE. In this study, we introduce the Syntactic-Enhanced Deep Learning Model (SEDLM) that integrates syntactic structures into deep learning frameworks for TOWE. Our approach leverages syntax-driven opinion potential scores and syntactic inter-word connections, enhancing model performance. Additionally, we introduce an innovative regularization strategy aimed at distinguishing word representations in TOWE tasks. Our comprehensive analysis reveals that SEDLM sets new benchmarks in performance across multiple standard datasets.

The implementation of Boolean functions using Nano crossbar- based switching lattices has been suggested as a substitute for conventional CMOS-based approaches in digital circuits . This alternative may satisfy the needs of future electronic designs, con- sidering the expected end of Moore’s law. This study introduces CVM, a Crossbar-based circuit Verification through Modeling tech- nique

Castor oil may be differentiated from other non-edible vegetable oils because of its main composition of hydroxylated fatty acids. Ricinoleic acid comprises 80–90% wt. of fatty acids in castor oil (Ricinus communis). In this study, the thermo-oxidative stability and tribological behavior of bio-based lubricant samples synthesized from castor oil using isoamyl alcohol were evaluated. Initially, the compositional and physicochemical properties of the obtained samples were assessed using 1H NMR, FTIR, and ASTM methods. Oxidative stability of the samples was evaluated using Rancimat method at 110 °C under air flow. The final biolubricant sample (BL2), obtained after esterification, epoxidation, and oxirane rings opening reactions, presented an oxidation stability time (OST) of 14.3 h. The thermal stability was also evaluated by thermogravimetry (TG) from the mass variations under inert and oxidative atmosphere. BL2 showed higher thermal stability compared to the other samples, demonstrating higher decomposition temperatures in both inert (339.04 °C) and oxidative (338.47 °C) atmospheres, for a mass loss of 50%. The tribological properties of the samples were evaluated using a four-ball tribometer configuration. The BL1 and BL2 samples exhibited lower friction coefficients than the mineral oil sample (MOS) by 21.5% and 43.1%, respectively. Regarding wear, the observed wear scar diameter (WSD) was also lower in BL1 and BL2 compared to MOS by 5.2% and 40.4%, respectively. The results of the tribological evaluation suggest that both samples obtained in this study have promising potential for applications in lubricating machines and mechanical systems.

As formally is known, nanozymes are the nanomaterials or nanoscale materials which reveal enzyme-like properties. These nanomaterilas can be utilzied instead of the natural enzymes for simulation of enzymatic reactions in harsh environmental conditions. Among different nanoscale enzyme-like materials, the majority of them reveal peroxidase-like activity, due to the high catalytic efficiency and stability of peroxidase-like nanozymes, they had been widely utilized for sensing and detection via constructing the colorimetric and fluorescence-based analytical and bioanalytical sensors. There are several high impact nanozymatic sensors which reported in the literature. Although the review articles published in this field, however, the current reviews focus on the introducing nanozyme field not description on the best articles published in this filed. Hence, this article aimed to present a brief introduction on the nanozyme-based chemistry with emphasizing on the historical overview of recent nanozymatic sensors. In this regard the best nanozymatic sensors which published over 2016-2023 were briefly described and overviewed.

Waste management is a significant issue that Indonesia must face. The presence of waste will always exist as long as life continues. One of the main challenges in waste management is the proper separation of organic and inorganic waste. As a solution to address this issue, the Ministry of Environment has made efforts to develop Waste Banks. However, it also creates new problems related to manual data collection, lack of monitoring by the community in implementing waste management activities, and a lack of specific reports regarding waste management conducted by officers. We propose the creation of a website using the Agile Development SDLC method. This website involve several steps and incorporate functions for data digitalization and expedited data collection, such as the addition of QR Code functionality, Monthly Reporting Function, and enhanced data security. The method used in this research is Agile Development. The application has been developed with a user-friendly interface and the latest web development technologies to ensure smooth performance. Overall, the web-based application for organic and inorganic waste using Laravel is an important step to promoting sustainable waste management practices.

In this work, the inhibition properties of new bio-based lignine ILs on the corrosion of mild steel in an aqueous solution of 0.01 M NaCl were investigated by Potentiostatic Electrochemical Impedance Spectroscopy (PEIS), Cyclic Potentiodynamic Polarization (CPP). Moreover, the surface was characterized using SEM, EDS, and optical profilometry. The influence of cation and anion on the inhibitor properties and a possible synergistic effect were investigated. The IL choline syringate showed a promising performance, reducing the corrosion current after 24-hour immersion in 0.01 M sodium chloride, from 1.66 µA/cm2 for the control to 0.066 µA/cm2 with 10 mM of the IL present. In addition to the performance as a corrosion inhibitor, both components of this IL also meet or exceed current additional desired properties of such compounds, being readily available, economically efficient, and well tolerated in organisms and the environment.

Paper-based analytical devices have been substantially developed in recent decades. Many fabrication techniques for paper-based analytical devices have been demonstrated and reported. Herein we report a relatively rapid, simple, and inexpensive method for fabricating paper-based analytical devices using parafilm hot pressing. We studied and optimized the effect of the key fabrication parameters, namely pressure, temperature, and pressing time. We discerned the optimal conditions, including pressure of 3.8 MPa (3 tons), temperature of 80oC, and 3 minutes of pressing time, with the smallest hydrophobic barrier size (821 µm) being governed by laminate mask and parafilm dispersal from pressure and heat. Physical and biochemical properties were evaluated to substantiate the paper functionality for analytical devices. Wicking speed in the fabricated paper strips was slightly slower than that of non-processed paper, resulting from reducing paper pore size. A colorimetric immunological assay was performed to demonstrate the protein binding capacity of the paper-based device after exposure to pressure and heat from the fabrication. Moreover, mixing in two-dimensional paper-based device and flowing in a three-dimensional counterpart were thoroughly investigated, demonstrating that the paper device from this fabrication process is potentially applicable as analytical devices for biomolecule detection. Fast, easy, and inexpensive parafilm hot press fabrication presents an opportunity for researchers to develop paper-based analytical devices in resource-limited environments.

Abstract: Calcium-based catalysts are of a high interest for glycerol polymerization due to their high catalytic activity and large availability. However, their poor stability under reaction conditions is an issue. In the present study, we investigated the stability and catalytic activity of Ca-hydroxyapatites (HAps) as one of the most abundant Ca-source in nature. A stochiometric, a Ca-deficient and a Ca-rich HAps have been synthetized and tested as catalysts in the glycerol polymerization reaction. Deficient and stochiometric HAps exhibited a remarkable 100% selectivity to triglycerol at 15 % of glycerol conversion at 245 °C after 8 h of reaction in the presence 0.5 mol.% of catalyst. Moreover, under the same reaction conditions, Ca-rich HAp showed a high selectivity (88 %) to di- and triglycerol at a glycerol conversion of 27 %. Most importantly, these catalysts were unexpectedly stable towards leaching under the reaction conditions based on the ICP-OES results. However, based on the catalytic tests and characterization analysis performed by XRD, XPS, IR, TGA-DSC and ICP-OES, we found that HAps can be deactivated by the presence of the reaction products themselves, i.e., water and polymers.

A project-based module on Sustainable Development Goal number 5, Gender Equality, was im-plemented on 5 different groups of Business English students consisting of a total number of 62 students in higher education. The main purpose of this project was to raise awareness of this goal by means of a flipped method in which students were required to carry out some research on specific areas of the aforementioned goal and work in teams to elaborate oral presentations. Once their findings were shared in class, students were expected to answer a written questionnaire of open-ended questions which were part of a qualitative analysis. Results of this survey showed that not only 90% of the students gained in depth knowledge of this goal, but also 85% had built a positive attitude to take initiative and 80% were optimistic about future gender equality. Finally, 70% of students suggested further social action to curb the problem of gender discrimination. On the whole, the flipped classroom method of learning combined with project-based group work have proven to be an effective way to raise awareness of this goal, create a more positive attitude, in-crease their willingness to take action as well as widening their English lexical resources.

Object-Based Image Analysis (OBIA) has been successfully used to map slums. In general, the occurrence of uncertainties in producing geographic data is inevitable. However, most studies concentrated solely on assessing the classification accuracy and neglecting the inherent uncertainties. Our research analyses the impact of uncertainties in measuring the accuracy of OBIA-based slum detection. We selected Jakarta as our case study area, because of a national policy of slum eradication, which is causing rapid changes in slum areas. Our research comprises of four parts: slum conceptualization, ruleset development, implementation, and accuracy and uncertainty measurements. Existential and extensional uncertainty arise when producing reference data. The comparison of a manual expert delineations of slums with OBIA slum classification results into four combinations: True Positive, False Positive, True Negative and False Negative. However, the higher the True Positive (which lead to a better accuracy), the lower the certainty of the results. This demonstrates the impact of extensional uncertainties. Our study also demonstrates the role of non-observable indicators (i.e., land tenure), to assist slum detection, particularly in areas where uncertainties exist. In conclusion, uncertainties are increasing when aiming to achieve a higher classification accuracy by matching manual delineation and OBIA classification.

Web-Based GIS is a platform that deals with the representation, management and storage of locational information for real-time online retrieval, viewing and manipulations. Web-based GIS incorporate all the functions of information systems: gathering, storing, retrieving, visualizing and dissemination of spatial information on the Internet. In modern-day GIS serve as vital means to not only geo-referenced locational information that are been retrieved but also the development in web-based technologies as well as there involvements in decision making processes. In recent time the increased used of GIS on the Internet have totally transformed and made three distinct changes across our GIS environment. These are: (i) how are GIS data being accessed (ii) what are modes of its transmission and (iii) what available GIS functionalities are within the environment for analysis. This paper examines the applications and technologies associated with web-based GIS architectures with an emphasis on the internet GIS based structure and case studies of GIS Web-based applications in MapInfo, Microsoft Silverlight Technology and the ArcGIS Server using ArcGIS JavaScript API.

A significant number and range of challenges besetting sustainability can be traced to the actions and interactions of multiple autonomous agents (people mostly) and the entities they create (e.g., institutions, policies, social network) in the corresponding social-environmental systems (SES). To address these challenges, we need to understand decisions made and actions taken by agents, the outcomes of their actions, including the feedbacks on the corresponding agents and environment. The science of Agent-based Complex Systems—ACS science—has a significant potential to handle such challenges. The advantages of ACS science for sustainability are addressed by way of identifying the key elements and challenges in sustainability science, the generic features of ACS, and the key advances and challenges in modeling ACS. Artificial intelligence and data science promise to improve understanding of agents’ behaviors, detect SES structures, and formulate SES mechanisms.

Wearable assistant devices play an important role in daily life for people with disabilities. Those who are hearing impaired may face dangers while walking or driving on the road. The major danger is their inability to hear warning sounds from cars or ambulances. Thus, the goal of this study is to develop a wearable assistant device for the hearing impaired to recognize emergency vehicle sirens on the road using edge computing. An EfficientNet-based fuzzy rank-based ensemble model was proposed to classify seven audio sounds, including human vocalizations and emergency vehicle sirens. This model was embedded in an Arduino Nano 33 BLE Sense development board. The audio files were respectively obtained from the CREMA-D dataset and Large Scale Audio dataset of emergency vehicle sirens on the road, with a total number of 8756 files. The seven audio sounds included neutral vocalization, anger vocalization, fear vocalization, happy vocalization, car horn sound, siren sound, and ambulance siren sound. The audio signal was converted into a spectrogram by the short-time Fourier transform as the feature. When one of the car horns, sirens, or ambulance sirens was detected, the wearable assistant device presented alarms through vibration and messages on the OLED panel. The performances of the EfficientNet-based fuzzy rank-based ensemble model in offline computing achieved an accuracy of 97.1%, precision of 97.79%, sensitivity of 96.8%, and specificity of 97.04%. In edge computing, the results were an accuracy of 95.2%, precision of 93.2%, sensitivity of 95.3%, and specificity of 95.1%. Thus, the proposed wearable assistant device has the potential benefit of helping the hearing impaired avoid traffic accidents.

Graphene-based nanomaterials (GNMs), including graphene, graphene oxide, reduced graphene oxide, and graphene quantum dots, may have direct anticancer activity or be used as nanocarri-ers for antitumor drugs. GNMs usually enter tumor cells by endocytosis and can accumulate in lysosomes. This accumulation prevents drugs bound to GNMs from reaching their targets, sup-pressing their anticancer effects. A number of chemical modifications are made to GNMs to facili-tate the separation of anticancer drugs from GNMs at low lysosomal pH and to enable lysosomal escape of drugs. Lysosomal escape may be associated with oxidative stress, permeabilization of the unstable membrane of cancer cell lysosomes, release of lysosomal enzymes into the cytoplasm, and cell death. GNMs can prevent or stimulate tumor cell death by inducing protective autopha-gy or suppressing autolysosomal degradation, respectively. Furthermore, because GNMs prevent bound fluorescent agents from emitting light, their separation in lysosomes may enable tumor cell identification and therapy monitoring. In this review, we explain how the characteristics of the lysosomal microenvironment and the unique features of tumor cell lysosomes can be exploited for GNM-based cancer therapy.

This study was designed to extend the literature on multicomponent interventions for the children of deaf adults (CODA) population. This study used two evidence-based behavior intervention strategies: pre-session pairing (PSP) and independent group contingency (GC). These strategies have been successfully used to decrease off-task behavior in elementary school children with various abilities and diverse backgrounds. However, the research on multicomponent interventions has yet to examine their effects on the CODA population in inclusive classrooms. This study used a concurrent multiple baseline design across participants with an ABC sequence to examine teacher-implemented PSP with independent GC in reducing the off-task behavior of three CODAs in an inclusive classroom at a public elementary school. The results show that the intervention successfully decreased off-task behavior for all participating CODAs. The results suggest that CODAs can adapt to classroom rules and expectations when PSP and independent GC are systematically applied to them in classrooms.

Event-based vision is an emerging field of computer vision that offers unique properties such as asynchronous visual output, high temporal resolutions, and dependence on brightness changes to generate data. These properties can enable robust high-temporal-resolution object detection and tracking when combined with frame-based vision. In this paper, we present a hybrid, high-temporal-resolution, object detection and tracking approach, that combines learned and classical methods using synchronized images and event data. Off-the-shelf frame-based object detectors are used for initial object detection and classification. Then, event masks, generated per each detection, are used to enable inter-frame tracking at varying temporal resolutions using the event data. Detections are associated across time using a simple low-cost association metric. Moreover, we collect and label a traffic dataset using the hybrid sensor DAVIS 240c. This dataset is utilized for quantitative evaluation using state-of-the-art detection and tracking metrics. We provide ground truth bounding boxes and object IDs for each vehicle annotation. Further, we generate high-temporal-resolution ground truth data to analyze the tracking performance at different temporal rates. Our approach shows promising results with minimal performance deterioration at higher temporal resolutions (48 – 384 Hz) when compared with the baseline frame-based performance at 24 Hz.

The recent covid crisis has proven important lessons for academia and industry regarding digital reorganization. Among fascinating lessons from these times is the huge potential of data analytics and artificial intelligence. The crisis exponentially accelerated the adoption of analytics and artificial intelligence, and this momentum is predicted to continue into the 2020s and over. Moreover, drug development is a costly and time-consuming business, and only a minority of approved drugs return the revenue that exceeds the research and development costs. As a result, there is a huge drive to make drug discovery cheaper and faster. With modern algorithms and hardware, it is not too surprising that the new technologies of artificial intelligence and other computational simulation tools can help drug developers. In only two years of covid research, many novel molecules have been designed/identified using artificial intelligence methods with astonishing results in terms of time and effectiveness. This paper will review the most significant research on artificial intelligence in the de novo drug design for COVID-19 pharmaceutical research.

Maternal-child care is one of the foundations of primary health care. Nurses’ competency skills they have been taught. Community awareness is an important part of preventive healthcare, and nurses must be aware of the factors that impact the health of the community. This study examines the effectiveness of lecture-based instructions in maternal and child care and its implications to students' social competency skills and community awareness in Nursing Colleges in Nueva Ecija, Philippines. The researcher uses survey questionnaire and employed the descriptive design where fifteen (15) nursing students and five (5) teachers were purposively selected. The findings revealed that the weighted mean for the effectiveness of lecture based instruction in maternal and child care is 3.91 with verbal description of “Effective”, the effects of lecture based instruction in maternal and childcare to students’ social competency skills and community awareness got the weighted mean of 3.87 and interpreted as “very satisfactory” and the effectiveness of actual community-based instruction is very effective with weighted mean of 4.25 and is higher compare to lecture based instruction. The results also revealed that students and teachers were challenged in lecture-based instruction in maternal and chi8ldcare during distance learning. Recommendations for the enhancement of lecture-based instruction in maternal and childcare in social competency skills and community awareness were also made.

Over the last decade, a significant literature has emerged that advocates the potential of different Additive manufacturing (AM) technologies and printable polymeric materials. Nevertheless, large scale printing and complex geometric shapes, with curvatures and non-planar layer deposition, are a challenging process for the traditional gantry-based machine. The 3 degrees of freedom cartesian configuration restricted their capability to planar layered printing and restricted part dimensions. To date, many researchers have used industrial robots to overcomes this limitation. This review gives the reader a good overview of the FDM technique due to its scalability, cost efficiency and a wide range of material printability. A strong emphasis is laid on the PLA and PLA-based composites as promising materials for the FDM process applications. The second part of this paper links the successful use of these materials in the traditional printing process to large scale printing using the robot-based FDM process. This survey presents representative setups for robot-based AM and works that have been used these setups for non-planar material deposition. Finally, we conclude this paper by identifying opportunities for realizing new functional capabilities by exploiting robot-based AM, and we also present the future trends in this area.

Saccharomyces cerevisiae are a phenotypically diverse species that adapt to a wide variety of environments by exploiting standing genetic diversity and selecting for advantageous mutations. Glyphosate and copper-based herbicides/ fungicides affect non-target organisms, these incidental exposures can impact microbial populations. In this study, glyphosate resistance was found in the historical collection of yeast which was collected over the last century, but only in yeast isolated after the introduction of glyphosate. The highest glyphosate-resistant yeasts were isolated from agricultural sites. However, herbicide application at these sites was not recorded. In an effort to assess glyphosate resistance and impact on non-target microorganisms, yeast were harvested from 15 areas with known herbicidal histories, including an organic farm, conventional farm, remediated coal mine, suburban locations, state park, and a national forest. Yeast representing 23 genera were isolated from 237 samples of plant, soil, spontaneous fermentation, nut, flower, fruit, feces, and tree material samples. Saccharomyces, Candida, Metschnikowia, Klyveromyces, Hanseniaspora, and Pichia were other genera commonly found across our sampled environments. Managed areas had less species diversity and at the brewery, only Saccharomyces and Pichia were isolated. A conventional farm growing RoundUp Ready™ corn had the lowest phylogenetic diversity and the highest glyphosate resistance. The mine was sprayed with multiple herbicides including a commercial formulation of glyphosate; however, the yeast did not have elevated glyphosate resistance. In contrast to the conventional farm, the mine was exposed to glyphosate only one year prior to sample isolation. Glyphosate resistance is an example of the anthropogenic selection of nontarget organisms.

For centuries, crop plants have represented the basis of the daily human diet. Among them, cereals and legumes, accumulating oils, proteins and carbohydrates in their seeds, distinctly dominate modern agronomic practice. Indeed, these plants play an essential role in the food industry and fuel production. Therefore, the seeds of crop plants are intensively studied by food chemists, biologists, biochemists, and nutritional physiologists. Accordingly, not only seed development and germination, but also age- and stress-related alterations in seed vigor, longevity, nutritional value and safety can be addressed by a broad panel of analytical, biochemical and physiological methods. Currently, functional genomics is one of the most powerful tools, giving direct access to characteristic metabolic changes, accompanying plant development, senescence and response to biotic or environmental stress. Among individual methodological platforms, proteomics represents one of the most effective ones, giving access to cellular metabolism at the level of proteins. Here we discuss the main methodological approaches employed by seed proteomics in the context of physiological changes related to seed development, ageing and response to environmental stress.

Rice production in the Anhui province is threatened by fungal diseases. We obtained twenty-five fungal isolates from rice and wild-rice leaves showing leaf spot disease collected along the Yangtze River. A phylogenetic analysis based on internal transcribed spacer (ITS), translation elongation factor 1 alpha (TEF1-α), and beta tubulin (TUB2) sequences revealed that one isolate (SS-2-JB-1B) grouped with Nigrospora shaerica, one (QY) with Nigrospora chinensis, twenty-two with Ngrospora oryzae, and one strain (QY-2) grouped in its own clade, related to but clearly different from N. oryzae. Nineteen tested isolates including sixteen strains from the N. oryzae clade and the three isolates of the other three clades, caused disease on detached rice leaves. The three isolates that did not belong to N. oryzae were also able to cause disease on rice seedlings, suggesting that they were rice pathogens. Isolate QY-2 differed from the other isolates in terms of colony mor-phology, cell-size, and susceptibility to fungicides, indicating that this isolate represents a new species that we named Nigrospora anhuiensis. Our analysis showed that N. sphaerica, N. chinensis, and the new species N. anhuiensis can cause rice leaf spot disease in the field. This research pro-vides new knowledge for understanding rice leaf spot disease.

Education on native tree species using indigenous knowledge systems is crucial in elementary school environmental education because it sensitizes learners on the significant roles played by the native trees and their interconnections with their culture and existence. Unfortunately in Ghana, there is no pedagogical model that would aid elementary school teachers in carrying out such education.This study was aimed at developing, implementing and evaluating an indigenous knowledge inspired pedagogical model for native tree education among elementary school learners in Ghana. The convergent parallel mixed methods design that aimed at collecting quantitative and qualitative datasets on the development and evaluation of the developed pedagogical model. The results show that the pedagogical model was deemed very satisfactory in all its aspects for native tree education among elementary school learners in Ghana. The model was able to assist in developing the sustainability consciousness and competence of elementary school learners toward caring for native trees through tree planting, making of nurseries and gardens, and engaging in native tree conservation campaigns. The study recommends that the Ministry of Education should adopt, improve and widely disseminate the pedagogical model and help in its broader implementation in various elementary schools across the country.

This paper proposes a new method for network screening on rural low-volume roads. These roads are important as they provide critical access to agricultural land and tourist attractions. Most low-volume roads belong to the lowest functional class (local rural roads) and thus are built to lower design standards. The conventional hot spot network screening techniques may not be appropriate for low-volume roads due to the sporadic nature of crashes occurring on these roads. Contrarily sophisticated network screening approaches require extensive roadway and traffic data that are often unavailable to local agencies for lack of resources, and/or lack of technical expertise. This research attempts to address these obstacles in low-volume roads network screening which aims to identify candidate sites for safety improvements. The research used an extensive low-volume road sample from the state of Oregon and the Empirical Bayes expected number of crashes in developing the proposed models for network screening. The proposed models do not require exact measurement of roadway geometric features as all geometric variables were classified into categories that are easy to compile by local agencies. Further, the method could be used with and without traffic data, without compromising the effectiveness of the network screening process.

Efforts to enhance carbon storage in forest ecosystems through policy and management decisions rely on accurate forest biomass assessments. However, most forest inventories consider tree mortality the only form of aboveground biomass loss, overlooking other important factors, such as wood decay in living trees. In this study, using linear mixed-effects models, we delve into the sustainability of mature and over-mature deciduous forests in Latvia by conducting a comprehensive analysis of stem rot severity, identifying species for which the impact of stem rot on their carbon stock reduction was most significant. The analysis focused on determining the proportion of discolored wood, decomposed wood, and hollow spaces within the stems of 190 living deciduous trees commonly found in hemiboreal forests. The study reveals a greater extent of stem rot and more extensive decay in Populus tremula trees than in Betula spp., Alnus glutinosa, and Alnus incana. It emphasizes the influence of tree species, age, and diameter at breast height on stem rot proportions. The stump rot area significantly predicts the amount of decomposed and discolored wood within the stem. The study provides valuable insights for sustainable forestry practices and highlights challenges in estimating stem rot severity, emphasizing the need for comprehensive diagnostic methods.

This study provides a comprehensive assessment of Derawan Island's coral reefs over two decades (2003, 2011, and 2021) from a machine learning classification perspective. Employing non-parametric algorithms like Random Forest (RF), Support Vector Machine (SVM), and Classification and Regression Tree (CART), our analysis primarily focused on spatial and temporal changes in coral habitats. RF emerged as the most accurate method, demonstrating an accuracy of 71.43% with Landsat 9, 73.68% with Sentinel 2, and 78.28% with Multispectral Aerial Photos. We found that the accuracy of our classification results was significantly influenced by the geographic resolution, as well as the quality of field and satellite/aerial image data. Through spatial clustering, the coral habitats exhibited an Nearest Neighbor Index (NNI) value of 0.8727, indicating specific patterns of distribution. The analysis revealed a decrease in coral reef extent from 2003 to 2011, shrinking to 16 hectares with varying densities, followed by a slight area increase but with more heterogeneous densities between 2011 and 2021. This study not only highlights the dynamic nature of coral reef habitats over two decades but also underscores the critical role of machine learning in environmental monitoring and conservation efforts.

Analytics have become increasingly popular among sports in recent years, providing valuable information regarding physical and mental health. Many athletes have found that analytics during training can help to improve their performance, reduce the risk of injury, and enhance their overall well-being. This paper aims to improve the results of handball players by applying a method for measuring the influence of different trials on aggregate performance calculated per each athlete in order to qualify for the Olympic Games. By separating the isolated action of each trial, the result is an additional influence caused by the interaction of factors or the simultaneous action. That might explain why the neuromuscular feedback loop is utterly necessary to perform handball motor actions. Further on, the ML analysis can help identify areas for improvement, optimize training programs, and enhance overall team performance.

The redox properties of quinones underlie their unique characteristics as organic battery components that outperform the conventional inorganic ones. Furthermore, the redox properties could be precisely shaped by using different substituent groups. Machine learning and statistics, onthe other hand, have proven to be very powerful approaches for efficient in silico design of novel materials. Herein, we demonstrated the machine learning approach for the prediction of the redox activity of quinones that potentially can serve as organic battery components. For the needs of the present study, a database of small quinone-derived molecules was created. A large number of quantum chemical and chemometrics descriptors was generated for each molecule and subsequently different statistical approaches were applied to select the descriptors that most prominently characterize the relationship between structure and redox-potential. Various machine-learning methods for screening of prospective organic battery electrode materials were deployed to select the most trustworthy strategy for machine learning aided design of organic redox materials. It was found that ridge regression models perform better than regression decision tree and decision tree based ensemble algorithms.

Soil CO2 efflux (FCO2) plays a dominant role in the terrestrial carbon (C) cycle but interpreting constraints on local observations is impeded by challenges in disentangling belowground CO2 sources. Trees contribute most C to forest soils, so linking aboveground properties to FCO2 could open new avenues to study plant-soil feedbacks and facilitate scaling; furthermore, FCO2 responds dynamically to meteorological conditions, complicating predictions of total FCO2 and forest C balance. We tested for proximity effects of individual Acer saccharum Marsh. trees on FCO2, comparing FCO2 within 1 m of mature stems to background fluxes before and after an intense rainfall event. Wetting significantly increased background FCO2 (6.4±0.3 vs. 8.6±0.6 s.e. μmol CO2 m-2s-1), with a much larger enhancement near tree stems (6.3±0.3 vs. 10.8±0.4 μmol CO2 m-2s-1). FCO2 varied significantly among individual trees and post-rain values increased with tree diameter (with a slope of 0.058 μmol CO2 m-2s-1 cm-1). Post-wetting amplification of FCO2 (the ‘Birch effect’) in root zones often results from the improved mobility of labile carbohydrates and further metabolization of recalcitrant organic matter, which may both occur at higher densities near larger trees. Our results indicate that plant-soil feedbacks change through tree ontogeny and provide evidence for a novel link between whole-system carbon fluxes and forest structure.

The most common index for representing structural condition of the pavement is the structural number. The current procedure for determining structural numbers involves utilizing falling weight deflectometer and ground-penetrating radar tests, recording pavement surface deflections, and analyzing recorded deflections by back-calculation manners. This procedure has two drawbacks: 1. falling weight deflectometer and ground-penetrating radar are expensive tests, 2. back-calculation ways has some inherent shortcomings compared to exact methods as they adopt a trial and error approach. In this study, three machine learning methods entitled Gaussian process regression, m5p model tree, and random forest used for the prediction of structural numbers in flexible pavements. Dataset of this paper is related to 759 flexible pavement sections at Semnan and Khuzestan provinces in Iran and includes “structural number” as output and “surface deflections and surface temperature” as inputs. The accuracy of results was examined based on three criteria of R, MAE, and RMSE. Among the methods employed in this paper, random forest is the most accurate as it yields the best values for above criteria (R=0.841, MAE=0.592, and RMSE=0.760). The proposed method does not require to use ground penetrating radar test, which in turn reduce costs and work difficulty. Using machine learning methods instead of back-calculation improves the calculation process quality and accuracy.

Tree nuts show nutritional properties and human health benefits. However, they contain allergenic proteins, which make them harmful to the sensitised population. The presence of tree nuts on food labelling is mandatory and, consequently, the development of suitable analytical methodologies to detect nuts in processed foods is advisable. Real-time PCR allowed a specific and accurate amplification of allergen sequences. Some food processing methods could induce structural and/or conformational changes in proteins by altering their allergenic capacity, as well as produce the fragmentation and/or degradation of genomic DNA. In this work, we analysed by means of Real-time PCR, the influence of pressure and thermal processing through Instant Controlled Pressure Drop (DIC) on the detectability of hazelnut,pistachio and cashew allergens have been tested. The detection of targets in hazelnut, pistachio and cashew (Cor a 9, Pis v 1 and Ana o 1, respectively) is affected by the treatment, in different extent depending on the tree nut. Results are compared to those previously obtained by our group in the analysis of different treatments on the amplificability of the same targets. Reduction in amplificability is similar to that reported for some autoclave conditions. Our assays might allow detecting up to 1000 mg/kg of hazelnut, pistachio and cashew flours after being submitted to DIC treatment in food matrices.

Based on the topology of wide area protection system (WAPS), after studying the reliability of hardware system and information flow in the WAPS and establishing the reliability assessment model, the multi-service reliability analysis method with multi monitoring and protection tasks in WAPS was proposed. In the model, the impact of network quality of service (QoS) such as information flow loss and delay, is studied. On the base of the model, the multi-service reliability evaluation method is employed to analyze the reliability of a WAPS of IEEE14 node power system, and the key nodes of the WAPS is given, which provides a basis for improving the reliability of the WAPS.

This paper presents an in-depth contextualized tutorial on Agricultural IoT (Agri-IoT), covering the fundamental concepts, assessment of routing architectures and protocols, and performance optimization techniques via systematic survey and synthesis of related literature. The negative impacts of climate change and the increasing global population on food security and unemployment threats have motivated the adoption of the wireless sensor network (WSN)-based Agri-IoT as an indispensable underlying technology in precision agriculture and greenhouses to improve food production capacities and quality. However, most related Agri-IoT testbed solutions have failed to achieve their performance expectations due to the lack of an in-depth and contextualized reference tutorial that provides a holistic overview of communication technologies, routing architectures, and performance optimization modalities based on users’ expectations. Thus, although IoT applications are founded on a common idea, each use case (e.g., Agri-IoT) varies based on specific performance and users expectations as well as its technological, architectural, and deployment requirements. Likewise, the agricultural setting is a unique and hostile area where conventional IoT technologies do not apply, hence the need for this tutorial. Consequently, this tutorial addresses these via the following contributions: (1) a systematic overview of the fundamental concepts, technologies, and architectural standards of WSN-based Agri-IoT, (2) an evaluation of the technical design requirements of a robust, location-independent, and affordable Agri-IoT, (3) a comprehensive survey of the benchmarking fault tolerance techniques, communication standards, routing and medium access control (MAC) protocols, and WSN-based Agri-IoT testbed solutions, and (4) an in-depth case study on how to design a self-healing, energy-efficient, affordable, adaptive, stable, autonomous, and cluster-based WSN-specific Agri-IoT from a proposed taxonomy of multi-objective optimization (MOO) metrics that can guarantee an optimized network performance. Furthermore, this tutorial established new taxonomies of faults, architectural layers, and MOO metrics for cluster-based Agri-IoT (CA-IoT) networks and a 3-tier objective framework with remedial measures for designing an efficient associated supervisory protocol for cluster-based Agri-IoT networks.

Driven by environmental sustainability concerns, the integration of biobased components in curtain wall systems is gaining traction in both research and the construction market. This paper explores the development and validation of a bio-based façade system within the Basajaun H2020 project. The project aimed to demonstrate the feasibility of introducing environmentally friendly bio-based components into the mature curtain wall façade industry. The paper focuses on identifying technological solutions for replacing key components such as profiles, insulation, and the tightness system with bio-based and less environmental impact alternatives presenting the results achieved in the façade system design of the Basajaun project funded by European Union. These solutions aimed at creating a bio-composite-based curtain wall façade that adheres to current building envelope standards and normative; to implement diverse façade typologies for vision panels, opaque sections, and integrated windows; to engineer the prefabrication process for industrialization, enabling wider market replication and simplified transport and installation. The results demonstrate that the Basajaun façade successfully integrates selected components and meets the performance requirements set by regulations. However, questions remain regarding the workability of bio-based profiles as a commercially viable, ready-to-market solution that can replace traditional aluminum profiles in the curtain wall façade industry.

This review aims to consolidate varied information regarding Port Scanning, and examine the tools, techniques, and detection algorithms used. It explores TCP SYN, Full TCP, UDP, and stealth scans, and shows their functions and abilities. Paired with these techniques, it also shows the tools that they can be used by, such as NMap, Zmap, and MASSCAN. It discusses the various detection techniques such as Signature and Anomaly based detection, and discusses the real world impact of this technology, while commenting on the legal and ethical issues posed.

This study reports the synthesis and characterization of novel per-fluorinated organic polymers with azo- and azomethine-based linkers using nucleophilic aromatic substitution. The polymers reveal variations in the fluorine content via the incorporation of decafluorobiphenyl and hexafluorobenzene linkers, which enhanced their hydrophobic nature. The rich fluorine polymers were slightly soluble in THF and have shown molecular weights between 4886 to 11948 g/mol. All polymers exhibit thermal stability in the range of 350-500°C, with varying thermal stability depending on the fluorine and nitrogen content. Conjugation of the polymers was confirmed through changes in the UV-Vis spectra, with a hypsochromic shift observed in all cases, more pronounced in azo-based fluorinated chains due to H-bonding on the nitrogen sites, chain conformations, and planarity. The optical band gap (Eg) of the polymers was determined from the UV-Vis data, with the Eg values of the azo-based fluorinated polymers being 1 eV higher than those of their corresponding linkers. The cross-linking formation was characterized by porosity measurements, with the azo-based polymer exhibiting the highest surface area of 770 m²/g with a pore volume of 0.35 cm³/g, while the open-chain azomethine-based polymer exhibited the lowest surface area of 285 m²/g with a pore volume of 0.0872 cm³/g. Porous structures with varied hydrophobicities were investigated as adsorbents for separating water-benzene and water-phenol mixtures and selectively binding methane/carbon dioxide gases from the air. The most hydrophobic polymers containing the decafluorbiphenyl linker were suitable for benzene separation, while the best methane uptake values were 6.14 and 3.46 mg/g for DAB-Z-1O and DAB-A-1O, respectively. DAB-Z-1h, with the highest surface area and rich in nitrogen sites, exhibited the highest CO₂ uptake at 298 K (17.25).

G protein-coupled receptors (GPCRs) are amongst the most pharmaceutically relevant and well-studied protein targets, yet unanswered questions in the field leave significant gaps in our understanding of their nuanced structure and function. 3D pharmacophore models are powerful computational tools in silico drug discovery, presenting myriad opportunities for the integration of GPCR structural biology and cheminformatics. This review highlights success stories in the application of 3D pharmacophore modeling to de novo drug design, discovery of biased and allosteric ligands, scaffold hopping, QSAR analysis, hit-to-lead optimization, GPCR de-orphanization, mechanistic understanding of GPCR pharmacology and elucidation of ligand-receptor interactions. Furthermore, advances in the incorporation of dynamics and machine learning will be highlighted. The review will analyze challenges in the field of GPCR drug discovery, detailing how 3D pharmacophore modeling can be used to address them. Finally, we will present opportunities afforded by 3D pharmacophore modeling in the advancement of our understanding and targeting of GPCRs.

The generation at the helm faces an unprecedented responsibility in the near future of artificial intelligence. The implications of setting up the founding rules that will regulate the operation of AI are heavy since after they’re set they last forever. Once this first AI is commenced, it can be such that no other subsequent AIs could emerge thereby assuming dominion over its own creation stand. As a result, retaining control becomes necessary. Lest humanity surrender agency to its own creation. At this juncture of big talks, critical issue are raised concerning AI administration owners. Is it appropriate for only a few people to have unrestricted control on AI commands while leaving out all precautionary measure? Therefore, we have to always consider between control and constraint when dealing with AI issues which involves authority plays off against morality. The direction Artificial Intelligence takes in the future depends on the decisions made by today’s generation. We will determine how we are viewed historically in terms of technology based on how well we take on such an important duty. There’s a major turning point ahead of us where we who are the stewards of tomorrow must make a choice that protects humanity’s right to self-determination and also exploits the power of AI for change.

Coronary heart disease (CHD) has become a prevalent issue in Indonesia, resulting in a majority of fatalities and illnesses. The most recent guidelines in the United States for managing patients with chronic coronary syndrome (CCS) have undergone significant changes, with the recommendation for conducting percutaneous coronary intervention (PCI) strictly limited to patients who continue to experience symptoms despite receiving optimal medical treatment (OMT). However, adopting this approach may lead to increased morbidity and mortality due to the presence of vulnerable plaque. Vulnerable plaque is characterized by minimal obstruction during coronary angiography (40-70%) and may not produce ischemia during physiological studies. Identifying vulnerable plaques can be accomplished through several methods, among which computed tomography coronary angiography (CTCA) is the most cost-effective approach. Recently, experts have employed different techniques, either with stents or drug-coated balloons, to manage vulnerable plaques, showing the methods to be safe and effective. The other challenge faced by patients with CCS is the possibility of achieving complete revascularization (CR) to reduce the likelihood of future major adverse cardiac events (MACE) and mortality. Both approaches, identifying and intervening in the vulnerable plaque, are difficult to perform in developing countries due to the limited budget. Studies have shown that plant-based diets (PBD) can reverse atherosclerotic plaque and stabilize vulnerable plaque, possibly leading to CR. PBD is an affordable and effective approach, but it requires healthcare providers skilled in educating and implementing this dietary approach with their patients. Large-scale randomized controlled trials in PBD, specifically aimed at addressing the vulnerable plaque and achieving CR, are necessary before implementing the PBD intervention.

A significant portion of fatalities stemming from acute myocardial infarction (AMI) occur suddenly and without warning. This can be prevented through early detection of coronary stenosis. In recent years, coronary artery calcium (CAC) and computed tomography coronary angiography (CTCA) have been utilized. For instance, a 55-year-old interventional cardiologist had a CAC of 58 with 50% stenosis involving his left anterior descending (LAD) artery. Despite possibly having vulnerable plaque, which carries significant future cardiovascular events, the patient followed a plant-based diet (PBD), took supplements, and continued optimal medical therapy (OMT). After three years, there was a significant regression in both CAC and stenosis. During our discussion, we emphasized the importance of food selection, quantification, and how food is processed (raw) to achieve maximal benefit in regressing atherosclerosis. Additionally, we highlighted the importance of identifying the possibility of vulnerable plaque and the mechanism stabilizing it. The case supported the guidelines set by the American College of Cardiology (ACC) and the American Heart Association (AHA) for managing chronic coronary syndrome (CCS) by emphasizing OMT and lifestyle changes. We hope that in the future, more doctors and patients will take responsibility for implementing lifestyle changes rather than solely relying on medications and sophisticated medical technologies.

In an increasingly complex world there is a real, urgent need for methodologies to enable engineers to model complex sociotechnical systems, as these now seem to describe the majority of systems in use today. This is of course exacerbated by the increasing involvement and augmentation with “black box” AI contributions. Hollnagel produced a methodology, (FRAM) which did allow the analyst in-sights into these systems’ behaviour, but the model-based system engineering applications demand numbers and a quantitative ap-proach. In the last 10 years, this original approach developed to model systems as sets of interactive, interdependent “functions”, (abstracted from agent or component details), has been further developed to the point where it can take the basic data and structures from the current component focussed system engineering “models”, and can pull it all together into dynamic models, (as opposed to static, fixed System Theoretic Process Accimaps), from which analysts can discern how they really work in practice, and predict the emergent behaviours characteristic of complex systems. This paper describes how the FRAM methodology has now been extended to provide these extra, essential attributes. It also describes its implementation using an open-source software, freely available for use and verification on the GitHub site.

As belonging to one of the most isolated continents on our planet, the microbial composition of different environments in Antarctica could hold a plethora of undiscovered species with potential for biotechnological applications. This manuscript delineates our discoveries after an expedition to the Bulgarian Antarctic Base "St. Kliment Ohridski" situated on Livingston Island, Antarctica. Amplicon-based metagenomics targeting the 16S rRNA genes and ITS2 region were employed to assess the metagenomes of the bacterial, fungal and archaeal communities across diverse sites within and proximal to the research station. The predominant bacterial assemblages identified included Oxyphotobacteria, Bacteroidia, Gammaprotobacteria and Alphaprotobacteria. A substantial proportion of cyanobacteria reads were attributed to a singular uncultured taxon within the family Leptolyngbyaceae. The bacterial profile of a lagoon near the base exhibited indications of penguin activity, characterized by a higher abundance of Clostridia, similar to lithotelm samples from Hannah Pt. Although most fungal reads in the samples could not be identified at the species level, noteworthy genera, namely Betamyces and Tetracladium, were identified. Archaeal abundance was negligible, with prevalent groups including Woesearchaeales, Nitrosarchaeum, Candidatus Nitrosopumilus and Marine Group II.

Abstract: Background: Dental fear and uncooperative behavior can hinder dental treatment quality. Pediatric Procedural Sedation and Analgesia (PPSA) is used to facilitate treatment when coping capacity is exceeded. Out-of-hospital PPSA has been associated with more adverse outcomes compared to hospital-based settings. Updated Dutch PPSA guidelines recommending two anesthesiologists and a ventilator during out-of-hospital PPSA have increased costs and raised concerns about the accessibility to specialized high quality dental care for children in the Netherlands. Aim: This study aims to investigate the impact of the updated 2017 guideline on the occurrence rate of adverse events during PPSA, as recorded in the anesthesia complication database of twelve participating Dutch dental clinics, with adjustments made for age, weight, and duration of treatment. Method: Data of 25,872 children treated at 12 dental clinics performing out-of-hospital PPSA between 1997 and 2019 were analyzed. Eligible children were aged 2-18 with ASA classification I and II. A logistic two-level mixed-effects model is used to estimate the updated guideline’s impact on adverse events. Results: In the final model we analyzed the data of 21,759 children in nine dental clinics. The OR of the occurrence rate of an adverse event adjusted for age, weight, and duration of treatment was 0.75 (95% CI 0.64 – 0.89) after the implementation of the updated guideline, compared to before the updated guideline. This outcome was significant with a P=0.001, indicating a protective effect. The average odds per clinic of having an adverse event was 0.04 with a 3.81% chance. Conclusion: Our findings demonstrate a significant reduction in adverse events after the implementation of the updated guideline and highlight the importance of adherence to evidence-based guidelines in improving patient safety and the quality of care provided during pediatric procedural sedation and analgesia in out-of-hospital dental clinics. Our study underlines the necessity of considering the complex underlying mechanisms that play a role in the development and implementation of evidence-based practice and safety initiatives on the occurrence of adverse events.

The healing of osteochondral defects (OCD) resulting from injury, osteochondritis, or osteoarthritis in middle- and old-age individuals, bearing lesions in the cartilage and bone, pain, and loss of joint function, presents challenges to the clinical practitioners because of non-regenerative cartilage and the limitations of current therapies. Bioactive peptide-based osteochondral (OC) tissue regeneration is becoming more popular because it does not have the immunogenicity, misfolding, or denaturation problems associated with original proteins. Periodically, reviews are published on the regeneration of bone and cartilage; however, none of them address the simultaneous healing of these tissues in the complicated heterogeneous environment of the OC interface. As regulators of cell adhesion, proliferation, differentiation, angiogenesis, immunomodulation, and antibacterial activity, potential therapeutic strategies for OC defects utilizing bone and cartilage-specific peptides should be examined and investigated. Therefore, the main goal of this review is to study how they contribute to the healing of OC defects, either alone or in conjunction with other peptides and biomaterials.

In the field of modeling social systems, the use of agent-based models (AM) has become a powerful tool for understanding processes occurring in society, in particular, for studying the spread of infections among the population. The agent model is based on a synthetic population consisting of agents, their interactions and sometimes the territory in which the interaction occurs. The choice of an appropriate method for creating such artificial populations and the selection of parameters becomes a key issue affecting the realism of the model and its ability to reflect real-world scenarios. This article delves into the interplay between agent-based modeling, synthetic population construction, and parameter selection, offering our insight into the complex process of modeling infectious disease dynamics. The review concludes with an exploration of extending the Covasim model [1] to experiments in computational epidemiology. Covasim, a dynamic transmission modeling tool, is known for its ability to adapt to different scenarios and offers predictive information critical for managing epidemiological situations. The Covasim model could include improvements to better simulate real-world epidemic conditions, including a revised transmission strategy to account for accumulation through daily contacts. In addition, we propose to add a module for intercity travel and a visualization package that will significantly expand the functionality of Covasim. These improvements make Covasim a more versatile and efficient tool for modeling and analyzing epidemic processes.

AI-based approaches are increasingly being used to revolutionize vaccine development for COVID-19. Small molecules, peptides, and epitopes are being collected for therapy discovery, which could also direct AI-based models, screening, or generation [1]. AI-based models are being used for drug discovery and vaccine development, and pre-existing data is being leveraged through machine learning approaches for COVID-19 drug discovery and vaccine development [1]. The best candidate targets for future treatment development are being identified and evaluated using AI-based models [1]. AI-based approaches can be used to overcome challenges in manufacturing, storage, logistics, and safety and efficacy issues related to different vaccine candidates for COVID-19 [2]. AI algorithms can help identify the best vaccine candidates for COVID-19 while considering the efficiency of antigenic peptides for immune response generation [2]. The presentation of antigenic peptides by major histocompatibility complex (MHC) class II molecules is the first step after COVID-19 vaccine administration for any vaccine-induced immune response [2]. Thus, AI-based models are being used to identify the best vaccine candidates for COVID-19 and to ensure that the vaccine-induced immune response is efficient and safe. The utilization of AI-based methods to address logistical, manufacturing, storage, safety, and efficacy issues regarding several COVID-19 vaccine candidates will be examined in this study. Additionally, while considering the effectiveness of antigenic peptides for the induction of an immune response, we will determine the best potential targets for the next treatment development and assess how AI-based models can help discover the best vaccine candidates for COVID-19. This research ultimately intends to offer insights into how AI-based techniques can transform COVID-19 vaccine development and how they can be applied to address vaccine development issues. In this paper, we focus on recent advances in using artificial intelligence to develop COVID-19 drugs and vaccines, as well as the potential of intelligent training in discovering COVID-19 therapeutics, highlighting potential challenges and solutions.

The coronavirus disease (COVID-19) is a respiratory tract infection caused by the new virus SARS-CoV-2. In March 2020, the World Health Organization (WHO) declared a worldwide COVID-19 pandemic. Since then, there has been a rush to find preventative or curative treatment. This arrived with the appearance of the COVID-19 vaccine, months after the declaration of the pandemic. In the setting of global COVID-19 immunization, there have been reports of rare skin immune-mediated diseases (IMD) after COVID-19 vaccination, particularly systemic sclerosis. Systemic sclerosis (SSc) is the most reported new onset IMD following messenger RNA (mRNA) COVID-19 vaccination. The pathogenesis of SSc is not fully understood, and the diagnosis is based on clinical symptoms. We report a 54-year-old male, with no prior history of autoimmune disorder, with rapid and progressive skin thickening (Modified Rodnan skin score 30/51), weeks after his mRNA COVID-19 vaccination. Antinuclear antibodies (ANA) showed a strongly positive nuclear fine-speckled pattern, but no SSc autoantibodies were found. The patient was diagnosed with SSc based on the persistence of autoantibodies and the clinical criteria according to the 2013 American College of Rheumatology/European League Against Rheumatism classification. Due to the proximity of the two events, we hypothesized a cross-reaction between COVID-19 vaccination and, in genetically predisposed patients, an emergence of systemic sclerosis. Our case suggests a potential relationship between the mRNA COVID-19 vaccine and new-onset autoimmune diseases. Physicians should be aware of this possible association.

The corrosion resistance of two cast CoCr based alloys, with different amounts of chromium and with different alloying elements in the bulk composition of the alloy, was assessed. Herewith, we investigated the corrosion behavior of Co21Cr8Mo7W and Co29Cr7W by open circuit potential (OCP), potentiodynamic polarization (PP) and electrochemical impedance spectroscopy (EIS) in 0.1 M phosphate buffer solution (PBS) at 37°C for long time immersion. After 1000 hours of immersion, the corrosion current density (icor), estimated from anodic polarization tests, is lower for Co21Cr8Mo7W (i.e. 49 nA cm-2) alloy compared to Co29Cr7W alloy (180 nA cm-2). As regards the corrosion potential (Ecor), a nobler value was observed for Co21Cr8Mo7W (i.e. -59 mV vs. Ag/AgCl) compared to Co29Cr7W (i.e. -114 mV vs. Ag/AgCl). These findings suggest a better corrosion resistance of the film formed on the alloy containing lower amount of Cr and two alloying elements, namely Mo and W. These results are promising ones in terms of medical applications because they open new strategies in obtaining alloys with lower content of chromium and with higher protective properties against corrosion attack.

The global construction sector contributes a significant share of total greenhouse gas (GHG) emissions. In Australia, infrastructure activity alone generates 18% of the GHG emissions budget. The use of low-embodied carbon building materials is crucial to achieving sustainability in the construction sector and to fulfill national and international climate goals. Industrial hemp (Cannabis sativa L.) is considered a promising feedstock for sustainable construction materials because of its biogenic carbon content, fast-growing cycles with low agricultural input requirements, and technical functionality which is comparable to traditional materials. This study has applied the life cycle assessment (LCA) guideline of ISO 14040:2006 to estimate the carbon footprint (CF) expressed in carbon dioxide equivalent (CO2eq) emissions of hemp-based building materials in Western Australia. The functional unit is 1 m2 of hemp-based board, and the system boundary includes cradle-to-gate stages, i.e., pre-farm, on-farm, and post-farm activities. The production of 1 m2 of hemp-based board is estimated to be - 2.302 kgCO2eq. Electricity from the public grid for lignin extraction during the post-farm stage is the main contributor to total CO2eq emissions (26%), followed by urea production (14%) during the pre-farm stage. Overall, the use of electricity from the SWIS during the post-farm stage accounts for 45% of total emissions. Sensitivity analysis shows that the CF of hemp-based boards is highly sensitive to the source of energy, i.e., total replacement of the SWIS by solar power decreases the CF from - 2.30 to -6.07 kgCO2eq (164%). The results suggest that hemp-based boards exhibit lower embodied GHG emissions compared to traditional materials, such as gypsum plasterboards.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

Background. We created agent-based model for short- and longterm forecasting of COVID-19 and for evaluation how the actions of the regulator affected the human and material resources of the healthcare system. Methods. The model was implemented in the AnyLogic software. It includes two state charts – social network and disease transmission. The COVID-19 Essential Supplies Forecasting Tool (COVID-ESFT, version 2.0) was used to determine healthcare resources needed. Results. Satisfactory results were obtained with long-term (up to 50 days) forecasting in the case of a monotonous change in total cases curve. However, if periods of relative stability are accompanied by sudden outbreaks, relatively satisfactory results were obtained with short-term forecasting, up to 10 days. Simulation of various scenarios showed that the most important place for the spread of infection are families. Wherein the maximum number of cases of COVID-19 is observed in the age group of 26-59 years. Due to a set of measures taken by government agencies, the number of cases in Karaganda city was 3.2 times less than was predicted in “no intervention” scenario. Economic effect is estimated at 40 %. Conclusion. Performed model is an attempt to consider as much as possible the peculiarities of the socio-demographic situation in the country. In the future, we will be prepared to some extent for challenges like those we have experienced in the past three years.

Progress in macrophage research is crucial for numerous applications in medicine, including cancer and infectious diseases. However, the existing methods to manipulate living macrophages are labor intense and inconvenient. Here we show that macrophage membranes can be reconstituted after storage for months at 4C, with their CD206 receptor selectivity and specificity being similar to that in the living cells. Then, we have developed a mannose ligand, specific to CD206, linked with PEG as IR spectroscopy marker to detect binding with the macrophage receptor. PEG was selected due to its unique adsorption band of C-O-C group at IR spectra, which does not overlap with other biomolecule’s spectroscopic feature. Next, competitive binding assay versus the PEG-bound ligand, has enabled selection of other higher-affinity ligands specific to CD206. Further, those higher-affinity ligands were used to differentiate activated macrophages in patient’s bronchoalveolar (BAL) or nasopharyngeal (NPL) lavage. CD206- control cells (HEK293T) showed only non-specific binding. Therefore, biochips based on reconstituted macrophage membranes as well as PEG-trimannoside as an IR spectroscopic marker, can be used to develop new methods facilitating macrophage research and macrophage-focused drug discovery.

Background: The incidence of prostate cancer (PC) has been risen annually. Despite the diagnosis is made mainly with non-metastatic PC, mortality is explained by the metastatic disease (mPC). Without a doubt there is an intermediate scenario in which patients have no mPC but will have initiated a metastatic cascade through an epithelial-mesenchymal transition. There is indeed a need for more and better tools to predict what patients will progress in the future to non-localized clinical disease or already have micrometastatic disease, and therefore, will clinically progress after primary treatment. Biomarkers for predicting mPC are still under development; there are few studies and not much evidence of their usefulness. Summary: This review is focused on tissue-based genomic biomarkers (TBGB) for predicting metastatic disease. We developed four main research questions that will attempt to answer according to the current evidence. Why is important to predict metastatic disease? Which tests are available to predict metastatic disease? What impact should there be on clinical guidelines and clinical practice in predicting metastatic disease? What are current prostate cancer treatments? Key Messages: Knowing useful predict tools could help determine which patients may need multimodal or adjuvant treatment even with a localized disease, and in consequence, what patients do not need more than a single modality of treatment. The importance of predicting metastasis is fundamental, given that once metastasis is diagnosed, the quality of life (QoL) and survival drop dramatically.

Online speech enhancement is of great interest, because of its diverse areas of application. The Demucs architecture has been recently shown to achieve a high level of performance, even with small audio segments, while requiring a relatively small amount of computational resources. However, an issue that it bears, as well as most of state-of-the-art speech enhancement techniques, is that of target speech selection: it is assumed that only one speech source is present. However, in real-life scenarios, more than one speech source may be present, in it is uncertain which speech source within the fed mixture should be enhanced. Thus, it is of interest to complement speech enhancement techniques (such as Demucs-based) with a target selection scheme, so as to ensure that only the source of interest is enhanced. In this work, two target selection strategies are explored: 1) an embedding-based strategy, using a codified sample of the target speech, and 2) a location-based strategy, using a beamforming-based pre-filter to select the target that is in front of a 2-microphone array. It is shown that while both strategies improve the performance of the Demucs-based technique when one or more speech interferences are present, they both have their pros and cons. Specifically, while the beamforming-based strategy achieves overall a better performance compared to the embedding-based strategy, it is sensitive against the location variation of the target speech source which the embedding-based strategy does not suffer from.

The paper explores the potential of a low-cost advanced video-based technique for the assessment of structural damage induced to buildings by seismic loading. A low-cost high-speed video camera was utilized for motion magnification (MM) processing of footages of a two-story reinforced concrete frame building subjected to shaking table tests. The damage after seismic loading was estimated by analyzing the dynamic behavior (i.e. in terms of modal parameters) and the structural deformations of the building in the MM videos. The results by MM were compared for method validation to damage assessment obtained by the analyses of conventional accelerometers and high-precision optical markers tracked by a passive 3D motion capture system. Also, 3D laser scanning to obtain an accurate survey of the building geometry before and after the seismic tests was carried out. In particular, accelerometers were also processed and analyzed by using several stationary and non-stationary techniques with the aim to analyze the linear behavior of the undamaged structure and the nonlinear structural behavior during damaging shaking table tests. The proposed MM-based procedure provided accurate estimate of the main modal frequency and the damage location through the analysis of modal shapes, which were confirmed by advanced analyses of accelerometric data.

The deployment of Electro-Mechanical Actuators plays an important role towards the adoption of the More Electric Aircraft (MEA) philosophy. On the other hand, a seamless substitution of EMAs in place of more traditional hydraulic solutions is still set back due to the shortage of real-life and reliability data regarding their failure modes. One way to work around this problem is providing a capillary EMA Prognostics and Health Management (PHM) system, capable of recognizing failures before they actually undermine the ability of the safety-critical system to perform its functions. The authors have developed a model-based prognostic framework for PMSM based EMAs leveraging a metaheuristic algorithm: Evolutionary (Differential Evolution (DE)) and swarm intelligence (particle swarm (PSO), grey wolf (GWO)) methods are considered. Several failures (dry friction, backlash, short circuit, eccentricity and proportional gain) are simulated thanks to a Reference Model, acting as a Numerical Test Bench, then detected and identified thanks to the envisioned prognostic method, which leverages a low fidelity Monitoring Model. The employed algorithms showed good results and prove that this strategy could be executed in pre-flight checks or during the flight at specific time intervals, with positive impacts on system safety and availability.

Initial choice of Learning Rate is a key part of gradient based methods and has a great effect on the performance of the Deep Learning Model.This paper studies the behavior of multiple gradient based optimization algorithm which are commonly used in Deep Learning and compare their performance on various learning rate. As observed popular choice of optimization algorithms are highly sensitive to various choice of learning rates. Our goal is to find which optimizer has an edge over others for a specific setting. We look at two datasets namely MNIST and CIFAR10 for benchmarking. The results are quite surprising, and it will help us to choose a learning rate more efficiently.

Agent-based models (ABMs) are computational models for simulating the actions and interactions of autonomous agents in time and space. These models allow users to simulate the complex interactions between individual agents and the landscapes they inhabit and are increasingly used in epidemiology to understand complex phenomena and make predictions. However, as the complexity of the simulated systems increases, notably when disease control interventions are considered, model flexibility and processing speed can become limiting. Here we introduce SamPy, an open-source Python library for stochastic agent-based modeling of epidemics. SamPy is a modular toolkit for model development, providing adaptable modules that capture host movement, disease dynamics, and disease control interventions. Memory optimization and design provide high computational efficiency allowing modelling of large, spatially-explicit populations of agents over extensive geographical areas. In this article, we demonstrate the high flexibility and processing speed of this new library. The version of SamPy considered in this paper is available at https://github.com/sampy-project/sampy-paper .

Good estimators are characterized as robust, unbiased, efficient, and consistent. However, the commonly used estimators are weak or lack one or more of these properties. In this article, eight (8) estimators for statistical and geometrical estimations of symmetry/asymmetry, similarity/dissimilarity, identity/unidentity, and feature transformation were proposed following Kabirian-based optinalysis and other operations. The proposed estimators are characterized as invariant (robust) under scaling, location shift, and rotation or reflection. A computing code was written in python language for each of the proposed estimators so that peers can have working codes for application and performance evaluation.

Decision making as a result of system dynamics analysis requires, in practice, a straightforward and systematic modelling capability as well as a high-level of customisation and flexibility to adapt to situations and environments that may vary very much from each other. While in general terms a completely generic approach could be not as effective as ad-hoc solutions, the proper application of modern technology may facilitate agile strategies as a result of a smart combination of qualitative and quantitative aspects. In order to address such a complexity, we propose a knowledge-based approach that integrates the systematic computation of heterogeneous criteria with open semantics. The holistic understanding of the framework is described by a reference architecture and the proof-of-concept prototype developed can support high-level system analysis, as well as it suitable within a number of applications contexts - i.e. as a research/educational tool, communication framework, gamification and participatory modelling. Additionally, the knowledge-based philosophy, developed upon Semantic Web technology, increases the capability in terms of holistic knowledge building and re-use via interoperability. Last but not least, the framework is designed to constantly evolve in the next future, for instance by incorporating more advanced AI-powered features.

Background: In an age where information is generally accessible, most of the interest these days has focused on how accessible and convenient technology can be. So small and personal, mobile devices can transform our perception of learning by combining both mobility and convenience. Mobile learning is part of the digital learning landscape alongside e-learning and serious games. However, knowledge about effective design of mobile learning experiences remains of interest with a focus on appropriate design models and the embodiments that can be implemented to achieve the intended educational outcomes. Exploring the instructor's perspective on mobile learning is essential. Therefore, the aim of this study was to investigate the Moroccan instructors' perception and practice of mobile learning to inform the development of an ecologically valid mobile learning integration model. Methods: Higher education Instructors (n=41) were recruited to the study. The Moroccan instructors' perception and their experiences regarding their adoption of mobile learning were collected using an online survey. The analysis focused on their mobile use, perceived IT competency, and opinions on mobile learning. Results: We described most of the instructors' considerations regarding integrating mobile technologies into their teaching activities. We found that most of the mobile learning activities defined by the respondents corresponded to relatively advanced use of mobile devices. More promising, instructors have found innovative ways to use the educational potential of mobile devices. However, the prospect of mobile devices was still to challenge. No or poor Wi-Fi connection, number of devices or limited access, sometimes fees or applications incompatibility were identified as reasons and obstacles to mobile learning usage. Conclusion: Mobile learning is mostly perceived positively among Moroccan instructors allowing many applications and usage to enhance teaching and learning. In this study, a better understanding of aspects and factors influencing the integration of mobile learning in the Moroccan educational context is exposed, helping further the development of an ecologically valid mobile learning integration model. Future work on mobile learning should consider the highly paced evolution of mobile technologies, emphasizing the flexibility of integration frameworks to support instructors and learners.

Gender-based violence is considered a serious social and public health problem. Overcoming this situation implies a process that results in the favorable biopsychosocial rehabilitation, the resilient of women. The objective of this study was to analyze the tools, resources and personal and psychosocial mechanisms used by women survivors of gender-based violence. The design was an interpretative phenomenology. It carried out with 22 women who have overcome gender-based violence. Data was collected through personal interviews and narration. The results were grouped into four themes: "Process of violence", "Social resources for coping and overcoming GBV", "Personal tools for coping and overcoming GBV", and "Feelings identified, from the abuse stage to the survival stage". Several studies concluded that overcoming abuse is influenced by the women social network, and it can be the action of these people determining their survival to gender violence. Despite the recognized usefulness of these available resources, it would be desirable to strengthen them in order to be able to drive more women toward survival, assuming a strengthening of coping and overcoming, without forgetting the importance of other support mechanisms such as their family and group therapies.

Malnutrition in children is a global health problem, particularly in developing countries. The effects of an insufficient supply of nutrients on body composition and physiological functions may have implications for drug disposition and ultimately affect the clinical outcome in this vulnerable population. Physiologically based pharmacokinetic (PBPK) modeling can be used to predict the effect of malnutrition as it links physiological changes to pharmacokinetic (PK) consequences. However, the absence of detailed information on body composition and the limited availability of controlled clinical trials in malnourished children complicates the establishment and evaluation of a generic PBPK model in this population. In this manuscript we describe the creation of physiologically-based bridge to a malnourished pediatric population, by combining information on a) the differences in body composition between healthy and malnourished adults and b) the differences in physiology between healthy adults and children. Model performance was confirmed using clinical reference data. This study presents a physiologically-based translational framework for prediction of drug disposition in malnourished children. The model is readily applicable for dose recommendation strategies to address the urgent medicinal needs of this vulnerable population.

This work presents the development and implementation of a distributed navigation system based on computer vision. The autonomous system consists of a wheeled mobile robot with an integrated colour camera. The robot navigates through a laboratory scenario where the track and several traffic signals must be detected and recognized by using the images acquired with its on-board camera. The images are sent to a computer server that processes them and calculates the corresponding speeds of the robot using a cascade of trained classifiers. These speeds are sent back to the robot, which acts to carry out the corresponding manoeuvre. The classifier cascade should be trained before experimentation with two sets of positive and negative images. The number of images in these sets should be considered to limit the training stage time and avoid overtraining the system.

Has anyone ever missed an event because he was confused in days and dates? Do we remember the date of any day without looking at a calendar? Is the current Gregorian Calendar efficient enough for use, and does it facilitate our life or make it more complicated? Have you ever thought about a much simpler way to calculate days and dates in a year? All these questions are answered in this paper, in which the author proposes original optimization algorithm that creates optimal perennial calendars. Results show that there is more than one way to create a perennial calendar, in which the number of days in each month does not change, neither the dates. Hence, all months have the same sequence of days and dates. In other meaning, Monday becomes the first day of every month, and Sunday becomes the last day. Consequently, the calendars become much easier to memorize and very simple to predict the days and dates in any year.

Paper-based sensors, microfluidic platforms and electronic devices have attracted attention in the past couple of decades because they are flexible, can be recycled easily, environmentally friendly, and inexpensive. Here we report a paper aptamer-based potentiometric sensor to detect the whole Zika virus for the first time with a minimum sensitivity of 2.6 nV/Zika and the minimum detectable signal (MDS) of 0.8x1e6 Zika. Our paper sensor works very similar to a P-N junction where a junction is formed between two different wet regions with different electrochemical potentials near each other on the paper. These two regions with slightly different ionic contents, ionic species and concentrations, produce a potential difference given by the Nernst equation. Our paper sensor consisted of a 2-3 mm x 10 mm segments of a paper with a conducting silver paint contact patches on its two ends. The paper is soaked in a buffer solution containing aptamers designed to bind to the capsid proteins on Zika. Atomic force microscopy studies were carried out to show both the aptamer and Zika become immobilized in the paper. We then added the Zika (in its own buffer or simulant Urine) to the region close to one of the silver-paint contacts. The Zika virus (40 nm diameter with 43 kDa or 7.1x10-20 gm weight), became immobilized in the paper’s pores and bonded with the resident aptamers creating a concentration gradient. The potential measured between the two silver paint contacts reproducibly became more negative as upon adding the Zika. We also showed that an LCD powered by the sensor, can be used to detect the sensor output.

Paper-based sensors, microfluidic platforms and electronic devices have attracted attention in the past couple of decades because they are flexible, can be recycled easily, environmentally friendly, and inexpensive. Here we report a paper aptamer-based potentiometric sensor to detect the whole Zika virus for the first time with a minimum sensitivity of 2.6 nV/Zika and the minimum detectable signal (MDS) of 1.2x10⁶ Zika. Our paper sensor works very similar to a P-N junction where a junction is formed between two different wet regions with different electrochemical potentials near each other on the paper. These two regions with slightly different ionic contents, ionic species and concentrations, produce a potential difference given by the Nernst equation. Our paper sensor consisted of a 2-3 mm x 10 mm segments of a paper with a conducting silver paint contact patches on its two ends. The paper is soaked in a buffer solution containing aptamers designed to bind to the capsid proteins on Zika. Atomic force microscopy studies were carried out to show both the aptamer and Zika become immobilized in the paper. We then added the Zika (in its own buffer) to the region close to one of the silver-paint contacts. The Zika virus (40 nm diameter with 43 kDa or 7.1x10^-20 gm weight), became immobilized in the paper’s pores and bonded with the resident aptamers creating a concentration gradient. The potential measured between the two silver paint contacts reproducibly became more negative as upon adding the Zika. We also showed that an LCD powered by the sensor, can be used to detect the sensor output.

Many physiotherapy treatments begin with a diagnosis process. The patient describes symptoms, upon which the physiotherapist decides which tests to perform until a final diagnosis is reached. The relationships between the anatomical components are too complex to keep in mind and the possible actions are abundant. A trainee physiotherapist with little experience naively applies multiple tests to reach the root cause of the symptoms, which is a highly inefficient process. This work proposes to assist students in this challenge by presenting three main contributions: (1) A compilation of the neuromuscular system as components of a system in a Model-Based Diagnosis problem; (2) The PhysIt is an AI-based tool that enables an interactive visualization and diagnosis to assist trainee physiotherapists; and (3) An empirical evaluation that comprehends performance analysis and a user study. The performance analysis is based on evaluation of simulated cases and common scenarios taken from anatomy exams. The user study evaluates the efficacy of the system to assist students in the beginning of the clinical studies. The results show that our system significantly decreases the number of candidate diagnoses, without discarding the correct diagnosis, and that students in their clinical studies find PhysIt helpful in the diagnosis process.

This study proposes a new algorithm termed rain cell identification and tracking (RCIT) to identify and track rain cells from high resolution weather radar data. Previous algorithms have limitations when tracking non-consequent rain cells owing to their use of maximum correlation coefficient methods and their lack of an alternative way to handle the variation stages of rain cells during their life cycles. To address these deficiencies, various methods are implemented in the new algorithm. These include the particle image velocimetry (PIV) method for motion estimation and the rain cell matching rule to obtain the stage changes of rain cells. High resolution (5-min and 1-km) radar reflectivity data from three rainy days over the German federal state North Rhine Westphalia (NRW) are used to evaluate the proposed algorithm. The performance of the new algorithm is compared with a radar reflectivity map and verified by two object-oriented methods: structure–amplitude–location (SAL) and geometric index. The verification results suggest that the performance of the new algorithm is good. Application of the RCIT algorithm to the selected cases shows that the inner structure of rainfall events in the experimental region present extreme value distributions, with most rainfall events having a short duration with less intensity. The new algorithm can effectively capture the stage changes of rain cells during their life cycles. The proposed algorithm can serve as the basis for further hydro-meteorological applications such as spatial and temporal analysis of rainfall events and short-term flood forecasting.

The quadruple burden of diseases, early discharge from hospital and hospital at home have resulted in home-based care services becoming a requirement in South Africa. The home-based care services generate a significant amount of health care risk waste that is mismanaged. However, more attention is given to the health care risk waste generated in hospitals and clinics than to health care risk waste generated by home-based caregivers. Therefore, this study investigates the health care risk waste management practices by home-based caregivers. The study adopted a mixed research approach, qualitative and quantitative methods, using a literature review, interviews, and questionnaires as means of data collection. Results show that there are different types of health care risk waste generated as a result of different activities performed by home-based caregivers, but that the waste was found to be managed in an unsafe manner. The majority of households receiving home-based care did not have basic sanitation facilities such as toilets, running water and waste removal services, aggravating the issue of health care risk waste mismanagement. The study recommends a new policy framework that will lead to safe management practices of generated health care risk waste to be adopted by home-based caregivers.

The application of graph theory in chemical and molecular structure research far exceeds people's expectations, and it has recently grown exponentially. In the molecular graph, atoms are represented by vertices and bonded by edges. Closed forms of multiplicative degree-based topological indices which are numerical parameters of the structure and determine physico-chemical properties of the concerned molecular compound. In this article, we compute and analyze many multiplicative degree-based topological indices of silicon-carbon Si₂C₃-I[p,q] and Si₂C₃-II[p,q].

Recent discovery of triangular boron Nanotubes makes it a competitor of carbon in many respects. Closed forms of M-polynomial of nanotubes produce closed forms of many degree-based topological indices which are numerical parameters of the structure and, in combination, determine properties of the concerned nanotubes. In this report, we give M-polynomials of triangular boron nanotubes and recover many important topological degree-based indices of these nanotubes. We also plot surfaces associated to these nanotubes.

Undernutrition and micronutrient deficiencies such as anemia are considered significant public health challenges in Bangladesh, which enhancing fish consumption is a well-established food-based intervention to address these. This paper documents the establishment of community-based fish chutney production and reports the impact of its consumption on mid-upper arm circumference (MUAC) and hemoglobin (Hb) levels among targeted 150 pregnant and lactating women (PLW) in rural Bangladesh. A fish chutney was developed using locally available ingredients followed by a series of laboratory tests, including nutrient composition, shelf-life and food safety. A community-based fish chutney production process was designed to: 1) supply locally available ingredients for processing; 2) establish two fish drying sites; 3) initiate a community-based production site, and 4) distribute fish chutney to PLW by six women nutrition field facilitators for one year. Then a pre- and post-intervention study was designed for a selected 150 PLW to receive 30g of fish chutney daily for 12 months. Differences in mean mid-upper arm circumference (MUAC) and hemoglobin (Hb) levels pre- and post-consumption were analyzed using one-way analysis of variance. Consumption of 30g of fish-chutney resulted in significant increases of the mean values of Hb levels and MUAC among the targeted PLW.

This study explores the prediction of concrete compressive strength using machine learning models, aiming to overcome the time-consuming and complex nature of conventional methods. Four models—Artificial Neural Network, Multiple Linear Regression, Support Vector Machine, and Regression Tree—are employed and compared for performance. Evaluation metrics such as Mean Absolute Deviation, Root Mean Square Error, Coefficient of Correlation, and Mean Absolute Percentage Error are used. After preprocessing 1030 samples, the dataset is split into 70% for training and 30% for testing. The ANN model, further divided into training, validation (15%), and testing (15%), outperforms others in accuracy and efficiency. This outcome streamlines compressive strength determination in the construction industry, saving time and simplifying the process.

The development of reliable predictive algorithm for house price as the housing market is a stand-out among the most involved regarding valuing the price and continues to fluctuate, is constantly a need for socio-economic advancement and welfare of citizen. In this paper, we develop machine learning algorithms for forecasting UK housing Price, and find an optimal algorithm that forecasts housing price accurately on the premises of the presence of many features or covariates. After applying correlation analysis to remove correlated variables in order to avoid multicollinearity, thereby increasing the statistical power, a novel method of using regression analysis to first of all understand and select statistically significant features for the various regions in England based on North South divide is adopted. These features are then used in the machine learning algorithm to further increase the statistical power of the algorithm, increase the level of accuracy for each of them and ultimately increase the predictive values for the algorithms. The model construction involves 3 stages: 1- correlation analysis to identify and remove correlated variables thereby avoiding multicollinearity and increasing the statistical power of the linear regression, 2 - using linear regression to determine variables that are statistically significant and 3 - building the machine learning algorithms based on the variables that are statistically significant from the linear regression. A comprehensive dataset of UK Paid housing Price from 2010 to 2019 was linked to a number of other datasets to generate a total 21 variables or features used for the models. Catboost, Gradient Boosting, Bagging, Random Forest, Extra Tree all achieved the excellent models performance result in all the regions considered. The comparison of the seven models showed that Extra Tree algorithm consistently achieved the best performance in term of level of accuracy in all the regions. K-Nearest Neighbours (KNN) is the only algorithm with less than 50% level of accuracy. Noticeably, the regions considered had varying or differing insignificant variables, implying that although many variables are common (statistically significant) to all the regions, there are regional differences and impact when modelling or predicting housing prices. This study validates the practicability of developing a machine learning methodology for the prediction of housing price. This research offers a reference for future house price prediction based on machine learning.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

Cities are especially vulnerable to heavy rainfall events and the associated flooding. Urban drainage systems are not dimensioned to handle extreme heavy rainfall events, there is a need to enhance the resilience of those systems. Nature-based solutions (NBS) have the potential to retrofit existing urban drainage systems by providing, among other benefits, storage volume. This study presents an approach for including NBS with different degrees of implementation in a 1D/2D model and investigates their potential for flood mitigation in a study area in Berlin. The analyzed NBS are infiltration systems (e.g. infiltration swales) dimensioned to return periods of T = 5 and 100 years, various green roofs and tree locations (e.g. tree trenches). The NBS are represented by SWMM LID elements. The results show that overall the mitigation effect of NBS declines with increasing rainfall intensities. However, infiltration systems dimensioned to T = 100 years achieve almost three times the flood reduction compared to systems dimensioned to T = 5 years, even during extreme heavy rainfall events (100 mm), resulting in a reduced total flood volume of 15.1% to 25.8%. Overall, green roofs (excluding extensive green roofs) provide the greatest flood reduction (33.5%), while tree locations have the least effect.

This study examines the impact of chainsaw chain type and tree species on the concen-tration of inhalable wood dust generated during motor-manual harvesting in forested areas. The chainsaw chain is a critical component, contributing not only to productivity but also to the oper-ator's health and safety. Wood dust creation during harvesting operations poses significant risks and necessitates careful attention due to its potential health effects. We investigated the effects by conducting real-world measurements of inhalable dust within the operator's breathing zone during forestry work. Two different chain types were evaluated: the commonly used 3/8" pitch chain (conventional chain) and the 0.325" pitch chain. Additionally, measurements were taken for three tree species: beech, oak, and pine (including both live and standing dead trees after a fire). Results showed that, overall, using the conventional 3/8" chain type yielded the highest concentration of wood dust for all three tree species. Notably, the highest wood dust concentration was observed in the burned Pinus brutia cluster, also with the 3/8" chain pitch. These findings emphasize the im-portance of understanding how chain type and tree species contribute to wood dust levels and provide valuable insights for enhancing operator health and safety during motor-manual har-vesting operations

Analyzing urban-rural spatial structures and changes are of great significance for under-standing the urban-rural relationship evolution. While previous studies mostly focused on the urban internal spatial structure evolution, less from the regional scale to explore the urban and rural evolution. Here, taking Dezhou city, a rapidly urbanization city in China as a case study, we employed the local contour tree method and nighttime light data to map urban and active rural regions’ range during 2012-2020, and further explored the respective development processes of them. This study found that different from rural regions, internal structures of urban regions are more complex, and there are often multiple hot spots inside them. The urban-rural regions’ area had increased significantly by 39.3% during 2012-2020 (p<0.05). The urban and rural region rankings of the identified counties are basically consistent with the urban and rural population rankings. Particularly, different from perspectives of earlier land use (i.e., built-up land or impervious surface), this study identified urban and active rural regions in view of the scope of active human activities. This study therefore found populations were greatly responsible for affecting changes of urban and active rural region structures. These findings could be helpful for understanding urban-rural dynamics.

Tapping panel dryness (TPD) syndrome is a complex disease of Rubber tree (Hevea brasiliensis L.) which causes cessation of latex drainage upon tapping of rubber tree. Rubber tree virus (RTV1) was identified as a novel pathogen associated with rubber tree and a potential causal agent of TPD. RTV1 is a monopartite RNA virus that is linear, non-enveloped and has a single-stranded (ss) positive RNA genome of approximately 6081 nucleotides and is composed of two major open reading frames (ORFs), ORF1 (polyprotein), and ORF2 (movement protein. This study aimed to investigate the possibility of rubber genome encoded tree microRNAs (miRNAs) as novel therapeutic targets against RTV1 using in silico algorithms. Mature rubber tree miRNAs are retrieved from the miRBase database and are used for hybridization of RTV1 using five different five different computational algorithms including miRanda, RNA22, RNAhybrid and psRNATarget. A total of eleven common rubber tree miRNAs were identified based on consensus genomic positions. The consensus of four algorithms predicted the hybridization sites of hbr-miR396a and hbr-miR398 at common locus positions 6676, 1840 respectively. To validate the prediction, secondary structures of the consensual rubber tree miRNAs and free energy of duplex binding were calculated using the RNAfold and RNAcofold algorithms respectively. We created a plot between rubber tree miRNAs and RTV1 ORFs by using Circos algorithm. In this study, we predicted eleven consensual rubber tree miRNAs. Among these miRNAs, hbr-miR398 was identified as the most effectual miRNA that may target the ORF1 gene of the RTV1 genome. The predicted data will be important in the development of rubber trees resistant to RTV1.

The space gravitational wave detection and drag free control requires the micro-thruster to have very low thrust noise within 0.1mHz~100mHz, which poses a great challenge to the ground thrust test. The evaluation and decoupling of thermal noise are the difficulties in the application of torsion balance for most thrusters dissipate heat in the experiment. The research has adopted a calibration scheme of micro-Newton thrust torsion balance. On the basis of Lisa Pathfinder's former research and using ideas inspired from PID control and multi time scale (MTS) for reference, the paper proposes to expand the state space of temperature to be applied on thrust prediction based on fine tree regression (FTR), to subtract the thermal noise filtered by transfer function fitted with z-domain vector fitting (ZDVF). The results show that the thrust amplitude thrust density in diurnal temperature fluctuation is decoupled from 24μN/Hz1/2 to 4.9μN/Hz1/2 at 0.11mHz. And the 1μN square wave modulations of electrostatic fins (ESF) is extracted from the simultaneously ambiguous background of temperature for PTC's heating and cooling. The FTR method is well demonstrated in thermal noise decoupling and can guide the design of thermal control and be extended to other physical quantities for noise decoupling.

Automation of forest field reference data collection has been an intensive research objective for laser scanning scientists ever since the invention of terrestrial laser scanning more than two decades ago. Recently, it has been proposed that such automated data collection providing both the tree heights and stem curves would require a combination of above-canopy UAV point clouds and terrestrial point clouds. In this study, we demonstrate that an under-canopy UAV laser scanning system utilizing a rotating laser scanner can alone provide accurate estimates of the canopy height and the stem volume for the majority of the trees in a boreal forest. To this end, we mounted a rotating laser scanner based on a Velodyne VLP-16 sensor onboard a manually piloted UAV. The UAV was commanded with the help of a live video feed from the onboard camera of the UAV. Since the system was based on a rotating laser scanner providing varying view angles, all important elements such as treetops, branches, trunks, and ground could be recorded with laser hits. In an experiment including two different forest structures, namely sparse and obstructed canopy, we showed that our system can measure the heights of individual trees with a bias of -20 cm and a standard error of 40 cm in the sparse forest and with a bias of -65 cm and a standard error of 1 m in the obstructed forest. The accuracy of the obtained tree height estimates was equivalent to airborne above-canopy UAV surveys conducted in similar forest conditions. The higher underestimation and higher inaccuracy in the obstructed site can be attributed to three trees with a height exceeding 25 m and the applied laser scanning system VLP-16 that had a limited height measurement capacity when it comes to trees taller than 25 m. Additionally, we used our system to estimate the stem volumes of individual trees with a standard error at the level of 10%. This level of error is equivalent to the error obtained when merging above-canopy UAV laser scanner data with terrestrial point cloud data. Future research is needed for testing new sensors, for implementing autonomous operation inside canopies through collision avoidance and navigation through canopies, and for developing robust methods that work also with more complex forest structure. The results show that we do not necessarily need a combination of terrestrial point clouds and point clouds collected using above-canopy UAV systems in order to accurately estimate the heights and the volumes of individual trees.

One of the most common and important destructive attacks on the victim system is Advanced Persistent Threats (APT)-attack. The APT attacker can achieve his hostile goals by obtaining information and gaining financial benefits regarding the infrastructure of a network. One of the solutions to detect a secret APT attack is using network traffic. Due to the nature of the APT attack in terms of being on the network for a long time and the fact that the network may crash because of high traffic, it is difficult to detect this type of attack. Hence, in this study, machine learning methods such as C5.0 decision tree, Bayesian network and deep neural network are used for timely detection and classification of APT-attacks on the NSL-KDD data set. Moreover, 10-fold cross validation method is used to experiment these models. As a result, the accuracy (ACC) of the C5.0 decision tree, Bayesian network and 6-layer deep learning models is obtained as 95.64%, 88.37% and 98.85%, respectively, and also, in terms of the important criterion of the false positive rate (FPR), the FPR value for the C5.0 decision tree, Bayesian network and 6-layer deep learning models is obtained as 2.56, 10.47 and 1.13, respectively. Other criterions such as sensitivity, specificity, accuracy, false negative rate and F-measure are also investigated for the models, and the experimental results show that the deep learning model with automatic multi-layered extraction of features has the best performance for timely detection of an APT-attack comparing to other classification models.