This paper investigates the influence of sample size and layer height on the elastic modulus of samples 3D printed by fused filament fabrication (FFF). Cubic samples of different sizes from either a stiff thermoplastic polymer (polycarbonate (PC)) or a soft polymer (thermoplastic polyurethane (TPU)) were printed at three different layer heights: 0.1 mm, 0.2 mm, and 0.4 mm. The samples were imaged using micro-computed tomography to visualize porosity and tested under compression. The results indicate that the elastic modulus of TPU varied with sample size, demonstrating size effects due to high porosity. In contrast, PC samples had a low void volume fraction and did not demonstrate statistically significant size effects on the elastic modulus. The variations in elastic modulus due to layer height were statistically significant for both materials. The highest elastic modulus was observed at 0.2 mm layer height for both materials across different sample sizes, which can be attributed to low void volume fractions. The study develops process-structure-property relations for PC and TPU samples manufactured by FFF. It provides new insights into the design guidelines for FFF based on the size effects. The results indicate that variations in mechanical properties due to size effects must be considered during the design stage for TPU to accurately predict the material’s behavior. Additionally, the locations of the printed parts that are subjected to higher loads should be printed closer to the heated print bed due to the lower void volume fraction observed in the section of the samples printed adjacent to the heated print bed.

This study explores the multifaceted influence of litter size, maternal care, exercise, and aging on rats' neurobehavioral plasticity and dentate gyrus microglia dynamics. Body weight evolution revealed a progressive increase until maturity, followed by a decline during aging, with larger litters exhibiting lower weights initially. Notably, exercised rats from smaller litters displayed higher body weights during mature and aged stages. Dentate gyrus volumes showed no significant differences among groups, except for aged sedentary rats from smaller litters, which exhibited a reduction. Maternal care varied significantly based on litter size, with large litter dams showing lower frequencies of caregiving behaviors. Behavioral assays highlighted the detrimental impact of a sedentary lifestyle and reduced maternal care/large litters on spatial memory, mitigated by exercise in aged rats from smaller litters. Microglial dynamics in the layers of dentate gyrus revealed age-related changes modulated by litter size and exercise. Exercise interventions mitigated microgliosis associated with aging, particularly in aged rats. These findings underscore the complex interplay between early-life experiences, exercise, microglial dynamics, and neurobehavioral outcomes during aging.

Although researchers have proposed various indentation size effect (ISE) models, these models often involve different form and number of parameters that can make our wonder which is the best in existed ISE models. Three types of ISE test data, namely, normal ISE, reverse ISE and transition of normal to reverse ISE, are used to evaluate the sixteen ISE models. The comparatively study indicates that H-J, N-G-Fs, N-G-H, N-G-A and N-G-Qs models can accurately predict the normal ISE. The reason for this is that the friction stress that is not related to dislocation activities or the indentation size effect of plastic zone has been introduced into these models. Therefore, these two factors should be considered in future ISE models. The sixteen ISE models are originally proposed to describe the normal ISE of different materials. However, to our surprise, some of these models are able to capture the reverse ISE and the transition of normal to reverse ISE of different materials. The determination coefficients (DC) of the sixteen ISE models are also determined for different materials. For reverse ISE, the highest DC value for NiCSi, TC4 and PED Ni are given by the EXP, N-G-Fs and N-G-A models, respectively. For the transition of normal to reverse ISE, the N-G-YC, N-G-Fs, and N-G-H models produce the maximum DC for ZrO2, Cu and Y2O3-ZrO2, respectively. Moreover, the mean DC of the N-G-Fs model is the maximum among the sixteen ISE models, followed by the N-G-H model, but they cannot accurately predict the reverse ISE. Therefore, the N-G-Fs and N-G-H models should be further modified to accurately predict the reverse ISE.

Sample size using prevalence has been one of the most important medical research methodologies and has been used in original articles more often than any other statistical tool available. The simple formula consists of variables interdependent and it is as important to understand how they influence each other as it is to learn to use the formula to calculate the sample size. With the choice of different amounts of precision and levels of confidence available to a medical researcher, it should be of paramount importance to understand what a slight change in choosing the parameter would mean at the end of the research. Understanding of different Z values, Levels of precision, and ranging Prevalence is required to understand the effect on the sample size and subsequently on the research. Topological representation using parameter ranges can be used to demonstrate this relationship.

Estimating parameters for multiple datasets can be time consuming, especially when the number of datasets is large. One solution is to sample from multiple datasets simultaneously using Bayesian methods such as adaptive multiple importance sampling (AMIS). Here we use the AMIS approach to fit a von Misses distribution to multiple datasets for wind trajectories derived from a Lagrangian Particle Dispersion Model driven from a 3D meteorological data. The primary objective is to characterise the uncertainties in wind trajectories in a form that can be used as inputs for predictive models of wind-dispersed insect pests and pathogens of agricultural crops for use in evaluating risk and in planning mitigation actions. Our results show that AMIS can significantly improve the efficiency of parameter inference for multiple datasets.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Recently perovskite solar cells have been paying attention of researchers. This comes from their high efficiency and stability. In this work, the change of some Optical and Electrical Properties of BaxFe(1-x)TiO4 thin films due to the change of the nanocrystal spacing and size were studied. A simple theoretical model based on the string theory was utilized to explain some of these empirical relations. The empirical results obtained indicated that an increase in the efficiency of the nano solar cell requires the energy gap to be narrow. Decreasing the nanocrystal size and spacing caused the energy gap to become narrower. The energy gap decreases also upon increasing the absorption coefficient and decreasing the transmission. This also requires increasing the conductivity and the magnetic permeability. The increase of the nanocrystal spacing decreases the absorption coefficient, electrical conductivity, and magnetic permeability, while it causes the transmission to increase. All these changes are explained using a simple string model beside Newton's laws. The capability of the string theory to explain this Nano quantum behavior comes from the fact that the string theory, like quantum theory, recognizes both the particle and the wave nature of the Nano system.

Keywords: liquid alloys, microstratification, dispersed particles, spontaneous dispersion, criteria for true (entropic) spontaneous dispersion, mechanisms of quasi-spontaneous dispersion, methods and results for assessing size of dispersed particles.

As companies increasingly undergo digital transformation, the role of talent management pro-cesses becomes pivotal in enhancing overall organizational performance. The research addresses the significance of talent management in corporate digital transformation, examining whether variations in the digitalization of these processes can be attributed to company size. A qualitative approach was employed, utilizing a questionnaire, collecting responses from 202 organizations across diverse sectors. Findings reveal disparities in digitalization throughout the talent man-agement process, with pronounced presence in the attracting, selecting, and rewarding phases, but diminishing in deployment and development, further declining in planning. A positive cor-relation between company size and adoption of specific digital platforms was observed. Larger enterprises exhibit greater utilization of digital platforms in talent deployment and development. Moreover, corporate communication tools are consistently utilized in the rewarding phase, irre-spective of company size. These findings offer practical insights for organizations to optimize their digitalization strategies based on their scale, thereby contributing to more effective and tailored digitalization endeavors. The uniqueness of this research lies in its exploration of the in-fluence of company size on the digitalization of talent management processes and its potential to explain variations across different stages of these processes.

Parkinson’s disease (PD) is the second-most common neurodegenerative disorder worldwide and is diagnosed based upon motor impairments. Non-motor symptoms are well-recognized in PD, and peripheral neuropathy is a frequent but poorly appreciated non-motor sign. Study of how the central and peripheral sensory systems are affected can contribute to the development of targeted therapies and deepen the understanding of the pathophysiology of PD. Although the cause of sporadic PD is unknown, chronic exposure to the pesticide rotenone in humans increases the risk of development of PD. Here, we aimed to investigate whether peripheral neuropathy is present in a traditional model of PD. Mice receiving intrastriatal rotenone showed greatly reduced dopamine terminals in the striatum and reduction in tyrosine hydroxylase-positive neurons in the Substantia nigra pars compacta and developed progressive motor impairments in hindlimb stepping and rotarod but no change in spontaneous activity. Interestingly, repeated testing using gold-standard protocols showed no change in gut motility, a well-known non-motor symptom of PD. Importantly, we did not observe any change in heat, cold, or touch sensitivity, again based upon repeated testing with well-validated protocols that were statistically well-powered. Therefore, this traditional model fails to replicate PD, and our data again reiterate the importance of the periphery to the disorder that is PD.

This study employs Principal Component Analysis to examine cranial measurements obtained from both extant and fossil specimens spanning 38 species and comprising over 300 individuals within the subfamily Cervinae. Our findings elucidate craniometric distinctions among cervids characterized by varying body sizes and certain evolutionary adaptations. While our results generally corroborate previous assertions regarding the limited craniometric variability among plesiometacarpal deer, they also unveil specific cranial adaptations within certain genera and species. The Principal Component Analysis of craniometric data revealed that giant and large-sized deer display significantly broader ecomorphological diversity in cranial shape compared to small-sized deer. Secondly, small-sized deer exhibit greater uniformity in their cranial shape, appearing densely clustered on the factorial map. Thus, we conclude that body size imposes ecological constraints, limiting the available niches due to eco-physiological factors. The study demonstrates that endemic insular deer do not evolve consistent craniometric features attributable to insular isolation, while the cranial proportions of medium-to-small sized deer delineate a ubiquitous morphological archetype characteristic of numerous cervid taxa spanning diverse phylogenetic lineages and sharing comparable body sizes. This group of "Dama-like" deer, characterized by similar body size, metabolic rates, ecological needs, and cranial morphometry, is referred to here as the fundamental eco-physiological type, typical of warm regions within the Palearctic and Oriental biogeographic realms..

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

In this paper, comprehensive analysis of combined effect of major influencing parameters on heat transfer in the single U-tube BHE (sBHE) and double U-tube BHE (dBHE) with two independent circuits was performed by using validated numerical heat transfer model. Geometrical parameters, such as shank spacing (with maximum, average and minimum values) and borehole diameter (large, medium and small borehole sizes) and borehole depth (shallow, average and deep borehole depths) as well as thermal conductivity of soil and grout which ranges from minimum to high value were considered. The combined impact of these parameters was included under four major cases: 1) combined effect of borehole depth, borehole size and shank spacing; 2) combined effect of borehole depth, and soil and grout thermal conductivity; 3) combined effect of soil and grout thermal conductivity and borehole size; and 4) combined effect of soil thermal conductivity, borehole size and shank spacing. Each of these major cases has nine different design options of both sBHE and dBHE. Series of results of heat transfer per unit borehole depth were generated for all the considered various cases. With the given parameters, the BHE case that provides highest heat transfer among the various cases of sBHE and dBHE were obtained.

The forest regeneration phase in Sweden commonly involves mechanical soil preparation followed by planting of Scots pine or Norway spruce seedlings. The prepared soil offers planting positions with different properties, including decreased damage by pine weevil (Hylobius abietis L.). Nitrogen fertilization can be applied at the time of planting to aid establishment of the seedlings. In this study we compared the effect of organic nitrogen-fertilization for different planting positions, and seedling sizes on early survival and growth of Scots pine and Norway spruce seedlings. The main planting positions were capped mound, hinge, and mineral soil. Seedlings planted close to organic material were categorized as “low quality positions”, since proximity to organic material increase pine weevil attraction. Higher mortality rates related to pine weevil damage were recorded for seedlings planted in the low-quality positions, regardless of seedling size or N-fertilization. Pine weevil attack rates increased with increasing seedling size. Growth was in general lowest in mineral soil positions. The effect of organic N-fertilization on growth was positive for spruce regardless of planting positions and seedling size, while depending on planting position and seedling size for pine, indicating that effects of organic N-fertilization depend on seedling species, -size and planting position.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

A study was carried out in a Waste Sorting Plant (WSP) located in France and treating dry recyclable household waste (DRHW) as well as dry recyclable commercial and industrial waste (DRCIW). The aim was to investigate the exposure to bioaerosol and dust. The aim of the study was to assess the extent to which the measurement of concentration, species composition and particle size distribution can contribute to a better assessment of the biological risks associated with exposure. Both stationary and personal bioaerosol and dust samples were collect in the (WSP). The results confirm that waste and waste sorting activities are sources of airborne fungi. Indeed, ambient concentrations ranged from 7.3×103 to 8.5×105 CFU/m3 for culturable moulds and up to up to 4 mg/m3 for dust. Personal exposure to inhalable dust was found up to 3 mg/m3 for dust and ranged from 8.6×103 to 1.5×106 CFU/m3 for fungi. Airborne fungal communities were found to be dominated by the Penicillium genera in both bioaerosols and settled dust samples, followed by the Aspergillus, Cladosporium, Wallemia, Mucor, and Rhizopus genera. Fungi were carried by particles of aerodynamic diameters mainly between around 2.0 and 10.0 µm. The findings dealing with size distribution and biodiversity of bioaerosols suggest that employees are exposed to complex bioaerosols during their work and helps to make a finer diagnosis of the risks involved, which is often difficult in the absence of any OEL for bioaerosols in general.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

To assess the impact of a deep learning (DL) denoising reconstruction algorithm applied to identical patient scans acquired with two different voxel dimensions, representing distinct spatial resolutions. This IRB approved prospective study was conducted at a tertiary pediatric center in compliance with the Health Insurance Portability and Accountability Act. We used a General Electric Signa Premier unit (GE Medical Systems, Milwaukee, WI) to acquire two DTI sequences of the left knee on each child at 3T: an in-plane 2.0 x 2.0 mm2 with section thickness of 3.0 mm and a 2 mm3 isovolumetric voxel, neither had an inter-section gap. We used a multi-band DTI acquisi-tion with fat-suppressed single-shot spin-echo echo-planar sequence (20 non-collinear directions; b-values of 0 and 600 sec/mm2). The MR vendor-provided a commercially available DL model applied with 75% noise reduction settings to same subject DTI sequences at different spatial res-olutions. We compared DTI tract metrics from both DL-reconstructed scans and non-denoised scans for femur and tibia, at each spatial resolution. Differences were evaluated using Wilcox-on-signed ranked test and Bland-Altman plots. When comparing DL versus non-denoised diffu-sion metrics in femur and tibia using the 2 mm x 2mm x 3 mm voxel dimension there were no significant differences between tract count (p = 0.1, p =0.14) tract volume (p = 0.14, p = 0.29), or tibial tract length (p=0.16); femur tract length exhibited a significant difference (p

Sustainable continuous cover forestry is defined and analyzed in several ways. The differential equation representing growth of the basal areas of individual trees, motivated by fundamental biological production theory by Lohmander (2017a), is analyzed and extended in different directions. From the solution of the differential equation, the basal area and the tree diameter are obtained as explicit functions of time. The diameter is a strictly increasing function of time. In the absence of competitors, the diameter increment is shown to be a strictly decreasing function of time. Hence, the diameter increment can also be interpreted as a strictly decreasing function of the diameter. Alternative forms of adjustment of the differential equation, with consideration of competition, are defined. If the competition is strong, with large trees in the vicinity of a particular tree, then the basal area increment, and the diameter increment, are reduced. The growth of a large tree is less sensitive than the growth of a small tree, to competition from other trees. Under strong competition, the basal area increment, and the diameter increment, are strictly concave functions of the size of the tree. The unique maximum of the diameter increment occurs at a higher diameter, if the competition increases. In dynamic equilibrium, the tree size frequency distribution is stationary. If natural tree mortality can be avoided via the harvest strategy, the tree size frequency distribution is a function of the size and competition dependent growth function, and the harvest strategy. Empirical tree size frequency data are used to simultaneously estimate parameters of a size and competition dependent growth function and the applied harvest strategy, via nonlinear optimization. The properties of the estimated growth function are consistent with the corresponding properties of the production theoretically motivated hypothetical function, and the properties of the estimated harvest strategy confirm the corresponding hypotheses. The R2 of the nonlinear regression exceeds 0.97. With access to an empirically estimated equilibrium tree size distribution, it is possible to: 1. Estimate size frequency relevant parameters of tree size and competition dependent growth functions for individual trees. 2. Estimate the applied harvest strategy. 3. Explain and reproduce the empirically estimated tree size equilibrium distribution.

The mushroom industry generates large amounts of stems, a co-product with valuable sensory and health characteristics. This work aimed to study the influence of particle size (L — >0.510 mm; LI — 0.510-0.315 mm; SI—0.315-0.180 mm; S — <0.180 mm) and species in the characterization and antioxidant activity of flours from stems of Agaricus bisporus (ABSF) and Pleurotus ostreatus (POSF). ABSF was rich in protein (14 g/100 g), calcium (428.23-700.77 mg/100 g), and sorbitol (22.57-26.60 g/100 g), while POSF in β-glucans (36.62-40.34 g/100 g) and linoleic acid (20.57-39.86 g/100 g of lipid). Both species were flush in amino acids with umami flavor. The highest hydration properties and oil holding capacity were exhibited in the S size of both species. ABSF showed elevated values for emulsifying activity than POSF. ABSF-S recorded the heightened antioxidant capacity in vitro, in consonance with the total phenolic compounds (0.91 mg/g). However, this antioxidant assays in POSF presented a positive correlation with β-glucans content. According to these results, there could be several food applications for these co-products, such as emulsifier stabilizer, sweetener or fortifier in the development of functional food.

This work is concerned with studying the change of some Optical and Electrical Properties of Ba_xFe_(1-x)TiO₄ thin films due to the change of the nano crystal size. Simple theoretical explanation based on the string theory was developed. The empirical results obtained indicated that the absorption coefficient, electrical conductivity, and the magnetic permeability increase upon decreasing the nano crystal size. However, the transmission coefficient, and the refractive index increase upon increasing the nano crystal size. All these changes are explained using a simple string model with the aid of Newton's laws. The capability of the string theory to explain this nano quantum behavior comes from the fact that the string theory recognize both the particle and the wave nature of the nano system. This is similar of course to the quantum approach which is based mainly on the dual wave particle nature of atomic systems and entities.

Single-particle inductively coupled plasma mass spectrometry (spICP-MS) has been used for particle size measurement of diverse types of individual nanoparticles and micrometer-sized carbon-based particles, such as microplastics. However, its applicability to the measurement of micrometer-sized non-carbon-based particles such as silica (SiO2) is unclear. In this study, the applicability of spICP-MS to particle size measurement of non-porous/mesoporous SiO2 micro-spheres with a nominal diameter of 5.0 µm or smaller was investigated. Particle sizes of these microspheres were measured using both spICP-MS based on a conventional calibration approach using an ion standard solution and scanning electron microscopy (SEM) as a reference technique and the results were compared. The particle size distributions obtained using both techniques were in agreement within analytical uncertainty. The applicability of this technique to the detection of metal-containing protein-binding mesoporous SiO2 microspheres was also investigated. Bound iron (Fe)-containing proteins (i.e., lactoferrin and transferrin) of mesoporous SiO2 microspheres were detected using Fe as a presence marker for the proteins. Thus, spICP-MS is applicable to the particle size measurement of large-sized and non-porous/mesoporous SiO2 microspheres; it has considerable potential for element-based detection and qualification of bound proteins of mes-oporous SiO2 microspheres in a variety of applications.

In the present paper, we efficiently solve the two-body problem for extreme cases such as those with high eccentricities. The use of numerical methods, with the usual variables, cannot maintain the perihelion passage accurately. In previous articles, we have verified that this problem is treated more adequately through temporal reparametrizations related to the mean anomaly through the partition function. The biparametric family of anomalies, with an appropriate partition function, allows a systematic study of these transformations. In the present work, we consider the elliptical orbit as a meridian section of the ellipsoid of revolution, and the partition function depends on two variables raised to specific parameters. One of the variables is the mean radius of the ellipsoid at the secondary, and the other is the distance to the primary. One parameter regulates the concentration of points in the apoapsis region, and the other produces a symmetrical displacement between the polar and equatorial regions. The three most used geodesy latitude variables are also studied, resulting in one not belonging to the biparametric family. However, it is in the one introduced now, which implies an extension of the biparametric method. The results obtained by the method presented here now allow a causal interpretation of the operation of numerous reparametrizations used in the study of orbital motion.

Background: Nowadays, the prevalence of digital device usage has shifted the demands for multifocal intraocular lenses. To accurately capture outcomes, clinical practice must evaluate digital reading performance. We aimed to assess the digital reading performance using a digital device in patients with diffractive multifocal intraocular lenses. Methods: Patients with bilateral diffractive multifocal intraocular lens implantation were included in the study. Monocular and binocular uncorrected and corrected visual acuity was measured using the LogMAR chart and the MNREAD application. Binocular uncorrected defocus curves were obtained using the LogMAR chart at 4m. The reading acuity was measured using the MNREAD application with positive and negative display polarities. The mean digital critical print size (CPS) was recorded using the MNREAD application at 40cm. Results: Our study reported uncorrected distance, intermediate, and near visual acuity were -0.084 ± 0.079, -0.014 ± 0.078, and 0.040 ± 0.081, respectively. The mean reading acuity at three months postoperatively with positive display polarity at 60cm and 40cm was -0.115 ± 0.102 and -0.008 ± 0.083, respectively. The mean digital CPS at three months postoperatively was 0.238 ± 0.100 logMAR. Conclusions: Incorporating digital reading performance measurements provides additional advantages in assessing the effectiveness of bilateral diffractive multifocal intraocular lens implantation.

Biochar is a carbon-rich material that recently received attention due to its increasing agronomical potential. The agricultural utilization of biochar relates to its potential to act in the soil as a soil conditioner, nevertheless, the complex information on the direct dependence of biochar physical properties (texture, particle size) and corresponding leaching and availability of organic molecules (e.g. the polycyclic and heterocyclic organic compounds) and inorganic mineral salts (based on micro– and macroelements) are still not consistent. These aspects were addressed in our study. A multi-elemental analysis (ICP-OES) was used to access the information on the aqueous-extractable and total contents of inorganic macro- and macroelements in used commercial biochar samples (purchased from Sonnenerde GmbH, Novoterrra Sonnenerde GmbH, Biouhel.cz, s.r.o.). Potassium (K) was identified as the major macroelement, responsible for alkaline pH and the conductivity of biochar extract. Our results indicate an indirect relation between the size fraction of biochar and the content of extractable K, sodium (Na), and calcium (Ca) and a direct relation with the contents of phosphorus (P) and magnesium (Mg). As the total determined amounts of inorganic elements were significantly higher compared to aqueous-extractable amounts, we believe it could indicate the potential for repeated release to the surrounding soil. These findings were also confirmed by the analysis of biochar samples obtained after the cultivation (duration of 2 years) in selected representative soil samples from the Czech Republic (Cambisol, Fluvisol, Regosol, Chernozem). Moreover, gas chromatography (GC) coupled with mass spectroscopy (MS) was further used to reveal the concentrations of available polycyclic aromatic and heterocyclic compounds in biochar samples. The detected concentration of these types of organic compounds were far below the certified limits. We believe our in-depth analysis could provide the necessary insight into the description of biochar mineral content, its connection to biochar texture, corresponding physicochemical properties and potential availability to leach nutrients to the soil. These findings could help in further assessment of the potential applications of biochar in modern agriculture as a soil conditioner.

The study delves into the critical examination of the Size of Loss distribution patterns in the context of auto insurance during pre- and post-pandemics, emphasizing their profound influence on insurance pricing and regulatory frameworks. Through a comprehensive analysis of the historical Size of Loss data, insurers and regulators gain essential insights into the probabilities and magnitudes of insurance claims, informing the determination of precise insurance premiums and the management of case reserving. This approach aids in fostering fair competition, ensuring equitable premium rates, and preventing discriminatory pricing practices, thereby promoting a balanced insurance landscape. The research further investigates the transformative impact of the COVID-19 pandemic on these Size of Loss patterns, given the substantial shifts in driving behaviors and risk landscapes. Also, the research contributes to the literature by addressing the need for more studies focusing on the implications of the COVID-19 pandemic on pre- and post-pandemic auto insurance loss patterns, thus offering a holistic perspective encompassing both insurance pricing and regulatory dimensions.

This study aimed to investigate the interactions between corn particle size (PS) and conditioning temperature (CT) on the performance, carcass traits, intestinal morphology, and immune responses in broilers fed a corn-soybean meal-based diet. A total of 360, one-day-old male broiler chicks (Ross 308) were randomly allocated into six dietary treatments in a 2×3 factorial arrangement, consisting of two corn PS (finely ground with geometric mean diameter (GMD) of 357 µm (PSF) vs. coarsely ground corn with GMD of 737 µm (PSC), and three CT [unconditioned (CTU), conditioned at 75◦C (CT75) and 90◦C (CT90)]. Birds accommodated in 30 pens with five replicates and 12 chicks per each. There was no interaction between corn PS and CT on growth performance and immune response of broilers at any growth phases. However, during the starter (0-10d) period, the average daily weight gain (ADWG) and feed conversion ratio (FCR) of PSF-fed birds were significantly improved compared to those fed PSC (P<0.05). During the starter (0-10d) and grower (11-24d) periods, increasing the conditioning temperature of corn increased the ADWG, while in the starter phase only the CT75 caused a lower FCR (P<0.05). Broilers fed PSF corn showed lowest FCR during the finisher (25-42d) period compared to those fed PSC (P<0.05). Conditioning corn at 75ºC reduced FCR during the finisher (25-42d) period compared to the birds fed CTU and CT90 corn (P<0.05). In whole experimental periods (1-42d), PSF and CT75 treatment increased the ADWG compared to the PSC and CTU (P<0.05). The CT75 treatment improved primary total anti-sheep red blood cell (SRBCs) titer (IgT) and IgM and secondary IgT and IgG responses compared to the other experimental groups (CTU and CT90) (P<0.05). No significant PS × CT interaction was found on Newcastle disease (ND) antibody titer of broiler chickens (P>0.05). Feeding CT75 corn reduced duodenum and jejunum relative length compared to the birds fed diets containing CTU corn. Significant PS×CT interactions (P<0.05) were observed for villus height, villus height to crypt depth, crypt depth, muscle thickness, and absorption surface area of jejunum. The highest carcass yield observed in PSF-CT75-group (P<0.05). In conclusion, the use of finely ground corn (PSF) conditioned at 75℃ (CT75) was beneficial to growth performance, development of the digestive tract, jejunum histomorphometry and the immune responses of broilers.

The Internet of Things (IoT) is a technological paradigm that has gained significant momentum that last decade and, among others, enables the development of intelligent and interoperable device networks. In this respect, it has triggered the creation and evolution of VANETs (Vehicular Ad Hoc Networks), which are initially implemented in order to guarantee the safety of the drivers and the avoidance of traffic accidents. The drawback is that this fast evolution flags serious concerns as far as the privacy of users is concerned, while the population of attackers or entities that try to eavesdrop and intercept information has significantly increased. This imposes a serious risk for drivers moving across a Smart City. The research presented in this paper aims to evaluate privacy protection mechanisms in VANET environments, based on their efficiency and security level ensured, considering the fact that VANETs provide limited resources to users/drivers. Moreover, the usage of the elliptic curve cryptography in reduced resources environments is discussed. Finally, this paper compares the performance of three cryptographic algorithms, i.e., Elliptic Curve Cryptography (ECC), Hyperelliptic Curve Cryptography genus 2 (HECC-2) and HECC genus 3 (HECC-3), employed for an efficient authentication and safe message transmission mechanism in VANETs, targeting to extract conclusions related to the implementation of each cryptographic scheme in this specific application area.

Phytoplankton guilds are commonly characterised by dominance effects, while the main contribution to biological diversity is given by rare species. Here, we analysed the influence of rare species on taxonomic and functional diversity, described by taxa richness and composition, cell size and size abundance relationships in phytoplankton guilds. We explore these relationships at global and regional scales by analysing phytoplankton guilds from five biogeographical regions: Northern Atlantic Ocean (Scotland), South-Western Atlantic Ocean (Brazil), South-Western Pacific Ocean (Australia), Indo-Pacific Ocean (Maldives) and Mediterranean Sea (Greece and Turkey). We have comparatively analysed the phytoplankton taxonomic diversity of the whole dataset and with the datasets obtained by progressively subtracting taxa occurring in the last 1%, 5%, 10% and 25% of both numerical abundance and overall biomass. Globally 306 taxa were identified across five ecoregions with only 27 taxa accounting for the 75% of overall numerical abundance and biomass; almost the 50% of taxa were lost on every step. The removal of 1% most rare taxa significantly affected the phytoplankton size-abundance relationships and body-size structure, strongly impacting on small taxa. The progressive removal of additional rare taxa did not further affect phytoplankton size-abundance relationships and size structure.

One of the most widely available and extensively produced varieties of industrial hemp, which generates a substantial amount of consumer-increasing waste in the form of hemp cellulose. In this study, recycling with a compressed and high-speed method that combines crushing and alkali treatment effectively converts leftover hemp fiber into ultrafine powder. SEM (Scanning Electron Microscopy), AFM (Atomic Force Microscope), FTIR (Fourier-transform Infrared Spectroscopy), and XRD (X-ray Diffraction) examined the original morphology of hemp fiber treated with alkali, fiber heated to 200 ℃, and crushed powder. Particle size, crystallinity, fiber surface, and strength increased and decreased. It became apparent that fiber strength decreased and fiber roughness significantly increased after alkali treatment. Fiber increased significantly, and crystallinity decreased after crushing. It was simple and effective for converting the leftover hemp fiber into micron-sized powder. In about 3 to 5 minutes, approximately 1 kg of dry ultrafine powder with a particle size of 10.44 μm was produced. This production method will significantly enhance future industrial applications of waste hemp fiber.

Chromosome segregation in female germ cells and early embryonic blastomeres is known to be highly prone to errors. The resulting aneuploidy is therefore the most frequent reason for termination of early development and embryo loss in mammals. And when compatible with embryonic and foetal development, aneuploidy leads into severe developmental disorders. The main surveillance mechanism, essential for protection of cells against aneuploidy, is the Spindle Assembly Checkpoint (SAC). And although all eukaryotic cells are perhaps able to mount SAC response, it is not clear, whether this pathway is active in all cell types, including blastomeres of early embryos. In this review, we will summarize and discuss the published literature with regards to mechanisms controlling chromosome segregation in early embryos. Our conclusion is that early embryos show limited capabilities to react to chromosome segregation defects, which might, at least partially, explain the widespread problem of aneuploidy during early development.

This study empirically analyzes how R&D expenditures affect firm value using a regression model for listed firms in Shandong Province, China. The dependent variable is measured by To-bin Q, which measures firm value, and the experimental variable among the independent varia-bles is R&D expenditure. In addition, financial leverage and firm size, which have been found to have a significant impact on firm value in previous studies, were selected as control variables. The study sample consisted of 554 data points analyzed over a nine-year period from 2010 to 2018. Without controlling for variables that affect firm value, the correlation analysis shows that R&D expenditures of listed firms in Shandong Province, China have a significant positive impact on firm value at the 1% level. For a more precise analysis, we ran a multivariate regression analysis controlling for other variables that affect firm value and found that R&D expenditure has a significant positive impact on firm value at the 1% level. These findings suggest that man-agers of listed companies in Shandong Province, China, need to actively engage in R&D activi-ties to increase firm value. Companies in Shandong Province, China, are currently experiencing very strong growth, and this study, which shows that R&D is the key to increasing the value of these companies, can help companies in Shandong formulate their business strategies.

The article presents a technology for producing nitrogen-containing nanoporous biocarbon with high degree of elemental composition homogeneity, confirmed by electron spectroscopy. The research explores the relationship among the electronic characteristics of supramolecular nanoporous carbon, its porous structure, and the capacitance at its interface with the electrolyte. The obtained biocarbon is characterized by micro and mesopores, as evidenced by the results of studies by the method of nitrogen adsorption/desorption. The specific area of the available porous surface was found to be 1247 m2/g. Comparing this result with the data of small-angle X-ray scattering, we conclude that micropores are open while mesopores remain closed. This material was found to have a saturation magnetization σs of 1.4 A∙m2∙kg-1 and a coercive force Hc of 10 kA/m. The impedance studies of electrochemical cells of supercapacitors made of the experimental biocarbon were carried out. Equivalent electrical circuits of the studied electrochemical processes were constructed and characterized.

To follow the growth and development of each tree (N = 1200) Pinus sylvestris L., var. Negorelskaya starting from the seed and continuing at the juvenile (or even generative) stage is the goal of an ambitious project to create a plant passport if possible. Five datasets of replenished empirical (tab-ular and file) and systematic data reflect the early results of a unique ongoing experiment conducted with families moved along a climatic gradient from the collection area (1731 degree days, 722 mm) to the experimental area (2326 degree days; 786 mm). Datasets of morphometric, VIS-spectrometric, and germination seed data, combined with the first results of biometric data (including the Dickson quality index) of seedlings produced from these seeds, will allow scientists in the future to conduct correlation and other statistical analysis, or train a neural network to determine the presence of connections between a seed and a plant. These data contribute to the early non-destructive diag-nosis and grading of seeds according to VIS-spectrometric properties. This dataset structure can complement the FLR-Library. In the future, by tracing seedlings in their early growth (for example, over three growing seasons at the site being restored), it will be possible to determine the degree of intensification of FRM production depending on the initial properties of the seed.

‘Inner mitochondrial membrane peptidase 2 like’ (IMMP2L) is a nuclear encoded mitochondrial peptidase that has been conserved through evolutionary history as has its target enzyme ‘mitochondrial glycerol phosphate dehydrogenase 2’ (GPD2). IMMP2L is known to cleave the mitochondrial transit peptide from GPD2 and another nuclear encoded mitochondrial respiratory related protein cytochrome C1 (CYC1). However, it is not known whether IMMP2L peptidase activates or alters the activity or respiratory related functions of GPD2 or CYC1. Previous investigations found compelling evidence of behavioural change in the Immp2lKD-/- KO mouse and in this study EchoMRI analysis found that many organs of the Immp2lKD-/- KO mouse were smaller and that the KO mouse had significantly less lean mass and overall body weight compared with wildtype littermates (p&lt;0.05). Moreover, all of the organs analysed from the Immp2lKD-/- KO had lower relative levels of mitochondrial reactive oxygen species (mitoROS). The kidneys of the Immp2lKD-/- KO mouse displayed the greatest decrease in mitoROS levels that were over 50% less compared with wildtype litter mates. Mitochondrial respiration was also lower in the kidney of the Immp2lKD-/- KO mouse compared with other tissues when using succinate as the respiratory substrate, whereas respiration was similar to wildtype when glutamate was used as substrate. When glycerol-3-phosphate (G3P) was used as the substrate for Gpd2 we observed ~20% and ~7% respective decreases in respiration in female and male Immp2lKD-/- KO mice over time. Together these findings suggest that the respiratory related functions of mGpd2 and Cyc1 have been compromised to different degrees in different tissues in the Immp2lKD-/- KO mouse. Structural analyses using AlphaFold2-Multimer further predicted that the interaction between Cyc1 and mitochondrial encoded cytochrome b (Cyb) in Complex III had been altered as had the homodimeric structure of the mGpd2 enzyme within the inner mitochondrial membrane of the Immp2lKD-/- KO mouse. mGpd2 functions as an integral component of the glycerol phosphate shuttle (GPS) which positively regulates both mitochondrial respiration and glycolysis. Interestingly, we found that nonmitochondrial respiration (NMR) was also dramatically lowered in the Immp2lKD-/- KO mouse. Primary mouse embryonic fibroblast (MEF) cell lines derived from the Immp2lKD-/- KO mouse displayed a ~27% decrease in total respiration comprised of a ~50% decrease in NMR and a ~12% decrease in total mitochondrial respiration where the latter was consistent with the decreases in substrate specific mitochondrial respiration reported here. This study is the first to report the role of Immp2l in enhancing Gpd2 structure and function, mitochondrial respiration, nonmitochondrial respiration, organ size and homeostasis.

Aedes aegypti is the main vector of various arboviruses including dengue, yellow fever, Zika and chikungunya virus. This mosquito species originated in Africa but has a wide range of distribution, colonising various ecological zones. The transmission dynamics of arboviruses depends on environmental factors, but also on mosquito life history traits including development time, fecundity, and longevity. The objective of the current study was to assess the Aedes aegypti immature development time, adult longevity, fecundity and body variation from different sampling localities. Aedes aegypti mosquitoes were collected as eggs from different geographical zones and cohorts of mosquitoes were reared in standardized laboratory conditions to assess the life history traits parameters. Emerged adults were discriminated into morphotypes according to the density of white scales on the first abdominal tergite. The means of fecundity, longevity, development time and body size were assessed, and linear models were fitted to the traits parameters to assess the effects of other covariables. Average Aedes aegypti development time was estimated to 7.35 days; 7.40 days; 6.98 days and 7.40 days respectively for Dori, 1200 logements, Bobo-Dioulasso and Toudweogo. The fecundity did not vary across study sites and was not associated with the body size. The longevity varied according to the study sites with the mosquitoes from Bobo-Dioulasso having the longest longevity while the shortest longevity was found at Dori. Fed mosquitoes had longer longevity compared to unfed ones. Morphological identification showed that Aedes aegypti aegypti-like mosquitoes were more predominant than Aedes aegypti formosus-like mosquitoes in all the study sites, suggesting the predominance of Aedes aegypti in the urban environment. Our data suggest that the geographical origin of Aedes aegypti mosquitoes in Burkina Faso has a little effect on its life history traits.

River bed materials serve multiple environmental functions as a habitat for aquatic invertebrates and fishes. At the same time, the particle size of the bed material reflects the tractive force of the flow regime in a flood and provides useful information for flood control. The traditional river bed particle size surveys, such as sieving, require time and labor to investigate river bed materials. The authors proposed a method to classify aerial images taken by unmanned aerial vehicle (UAV) using convolutional neural networks (CNN), our previous study showed that terrestrial riverbed material could be classified with high accuracy. In this study, we attempted to classify riverbed materials distributed in shallow waters where the bottom can be seen from UAVs. After training the CNN to classify the images with the same grain size as being in the same class even if the surface flow types taken overlapping the riverbed material were different, the total accuracy reached 90.3%. Moreover, the proposed method was applied to the wide-ranging area to determine the distribution of the particle size. In parallel, the microtopography was surveyed using Lidar-UAV, and the relationship between the microtopography and particle size distribution was discussed. In the steep section, coarse particles were distributed and formed a rapid. Fine particles were deposited on the upstream side of those rapids, where the slope had become gentler due to the damming. There was good agreement between the microtopographical trends and the grain size distribution.

There has been controversy around the mechanical properties of Mg-alloys such as AZ91D and the large variation of these have been seen. The current paper addresses this controversy through specially fabricated samples combined with tensile testing and advanced metallography, including 3D reconstruction of the phases. The results show that despite a more brittle nature of the fracture, the equiaxed microstructure displays a better elongation as compared to a dendritic microstructure. The main conclusion is that this is primarily caused by the nature, or tortuosity, of the Mg17Al12-network in the material.

Inland capture fisheries play a critical role in supporting food security and livelihoods in West Africa. Therefore, it is important to evaluate genetic health of exploited fish populations. The African bonytongue, Heterotis niloticus, supports important commercial and subsistence fisheries in West Africa. Sharp declines of stocks have been reported, however. Herein, we estimate contemporary effective population sizes (Ne) of four Heterotis populations in Nigeria, three in Benin, and five in Cameroon using the Linkage Disequilibrium method with correction for age structure. Ne estimates were used to assess genetic short-term (i.e., inbreeding depression) and long-term (i.e., loss of evolutionary potential) risks. Analyses failed to obtain Ne point estimates for two populations. For the remaining ten populations, corrected Ne point estimates fell well below 500, the minimum recommended for populations to retain evolutionary potential; with eight populations below 100 (range 2.8–83.5), the minimum recommended to avoid inbreeding depression, one borderline (100–125), and one above this threshold (312–392). The lower 95% confidence interval bound of Ne for eleven populations was very small (0.7–14.6), and for the remaining population it was 44.2. Accordingly, all populations examined can be considered potentially at risk of inbreeding depression.

This feature study attempts on setting a granules involving mesoscopic matter-aggregation context as a problem of passing locally by the matter-aggregating system from classical stochastic (mesoscopic limit) to a quantum description (nanoscale quantum-size effect limit). A d-dimensional entropy-production aggregation of the granules-involving matter is considered in terms of a (sub)diffusive realization. It turns out that when taking a full d-dimensional pathway of the aggregation toward the nanoscale, one is capable of disclosing a Heisenberg type (diffusional) relation, setting up an upper uncertainty bound for the (sub)diffusive very slow granules-including environment that matches the quantum limit of h/2pm (m– average mass of a granule; h – the Planck’s constant) for the diffusion coefficient of the aggregation, likely first proposed by Fürth in 1933, and qualitatively foreseen by Schrödinger some years before, both in the context of a diffusing particle cluster. The classical-quantum passage uncovered here, also termed insightfully the quantum-size effect (as borrowed from the quantum dots’ parlance), works properly for the three-dimensional (d=3) case, making use of a substantial physical fact that the (nano)granules interact readily via their surfaces with the also granular surroundings in which they are immersed. This natural observation is embodied in the basic averaging construction of the diffusion coefficient of the aggregation of interest. Certain, possibly biomedical, applications of the model can also be viewed by prospective inspection of tiny inhomogeneities in nanofibrillar and/or lamellar matter for which certain numerical realizations are plausible to prepare based on thorough nanoscale experiments.

ABSTRACT: Waterlogging is a common abiotic stress in global maize production. Maize flowering stage (from tasseling to silking) is more fragile to environmental stresses among different growth stages. The effects of waterlogging at flowering stage on the grain yield and starch quality of waxy maize were studied using Suyunuo5 (SYN5) and Yunuo7 (YN7). The grain yield and starch concentration of both hybrids were reduced by waterlogging. The size of starch granules and proportion of small-molecule amylopectin increased in SYN5 and decreased in YN7 when plants suffered waterlogging at flowering, in contrast to the change trend of relative crystallinity. The pasting viscosities and gelatinization temperatures were reduced, whereas the gelatinization enthalpy was unaffected by waterlogging in both hybrids. Our study indicated that waterlogging at flowering reduced the grain yield, restricted starch deposition, and deteriorated the pasting property of waxy maize. Between the two hybrids, YN7 and high pasting viscosities and low retrogradation percentage than SYN5, indicated its advantages on produce starch for viscous and less retrograde food. Results provide information for utilization of waxy maize grain in food production.

In order to study the collapse failure of shaft wall of high depth inclined ore-pass under ore impact wear behavior, 25 ore-passes in a deep mine in Yunnan, China were investigated. Considering the ore-pass structural characteristics and the impact wear effect of ore on shaft wall, the shaft wall damage model of high depth inclined ore-pass is constructed based on the contact mechanics theory. Furthermore, No. 1#, 2#, 3# and 9# ore-passes of the mine are taken as examples for analysis, and the three results of theoretical analysis, numerical simulation and engineering case are used for comparison and verification. The shaft wall damage degree is predicted, and the damage mechanism between total shaft wall damage volume Qtol and ore-pass depth H, ore-pass dip angle θ, inclined angle of chute α, shaft diameter D and ore block size P is quantitatively investigated. The results show that the rationality of the proposed model is verified by numerical analysis and field engineering situations. Moreover, the deeper ore-pass depth H, the more shaft wall damage volume Qtol with the increase of collision frequency. Qtol increases exponentially with P and increases gradually with D. With the increase of θ or α, Qtol increases generally first and then decreases. Therefore, Qtol can be effectively reduced by selecting the appropriate structure parameters of ore-pass and adopting the technology of drilling straight ore-pass. This work provides technical support for long period safe operation of high depth inclined ore-pass.

This paper presents a comprehensive study based on multiphase seepage and wellbore multiphase flow theories. It establishes a gas intrusion rate calculation model that considers various factors including formation pore permeability, bottomhole pressure difference, drilling fluid rheology, and surface tension. Experiments were conducted to investigate the gas intrusion mechanism under shut-in conditions, and the experimental results were employed to validate the reliability of the proposed gas intrusion rate calculation method. Furthermore, the research explores the transportation rates of single bubbles and bubble clusters in drilling fluid under shut-in conditions. Meanwhile, empirical expressions were derived for the drag coefficient for single bubbles and bubble clusters in the wellbore. These expressions can be used to calculate gas transportation rates for various equivalent radii of single bubbles and bubble clusters. Additionally, a method was developed for calculating the rising velocity of bubble clusters in water based on experimental results. The study reveals that the average bubble size in the bubble cluster is significantly smaller than the size of the single bubble generated from the orifice. When the viscosity of the drilling fluid is low, the bubble cluster transportation velocity exhibits a positive correlation with the average bubble diameter. When the average bubble diameter exceeds 1 mm, the bubble velocity no longer varies with the change in the bubble cluster diameter. The initial bubble size of intrusive gas, the transportation speed of intrusive gas in the wellbore, the gas intrusion rate, and variations of the wellbore pressure after gas intrusion were analyzed. The research results provide theoretical support for wellbore pressure prediction and pressure control under shutdown conditions.

Complex-structured polymeric microparticles hold significant promise as advance in next-generation medicine mostly due to demand from developing targeted drug delivery. However, the conventional methods for producing these microparticles of defined size, shape and sophisticated composition often face challenges in scalability, reliance on specialized components such as micro-patterned templates, or have limited control over particle size distribution and cargo release kinetics. In this study, we introduce a novel and reliably scalable approach for manufacturing microparticles of defined structures and sizes with variable parameters. The concept behind this method involves the deposition of a specific number of polymer layers on a substrate with low surface energy. Each layer can serve as either the carrier for cargo or a programmable shell-former with predefined permeability. Subsequently, this layered structure is precisely cut into desired-sized blanks using a laser. The manufacturing process is completed by applying of heat to the substrate what results on sealing the edges of the blanks. The combination of the high surface tension of the molten polymer and the low surface energy of the substrate enables the formation of discrete particles, each possessing semi-spherical or other designed geometries determined by their internal composition. Such anisotropic microparticles are envisaged versatile applications.

In this paper, the effects on the rheological properties, particle size distribution, and fluorescence properties of red wine were investigated under microwave irradiation, and the mechanism of the effects of microwave irradiation on the sensory properties of red wine was discussed. The results showed that the effect of microwave on the rheological properties in red wine could be fitted by the Power-law model and Carson model, through the analysis of the rheological constants, yield stress, and viscosity coefficient of wine, it was found that microwave treatment could improve leg phenomenon and thickening effect by the change of rheological properties; the particle size distribution in wine indicated that microwave irradiation did change the particle size distribution through friction effect and oxidative polymerization, resulting in the wine’s visual effect and mouthfeel; the wine quality could be improved by enhancing the fluorescence intensity under different microwave conditions, which meant that microwave technology could speed up the formation of fluorescent substances, such as the polymerization of flavan-3-ols. In conclusion, microwave treatment could modify the sensory characteristics of wine, and further provide the theoretical basis for the application of microwave in winemaking.

Abstract: A biomaterial is proposed for closing extensive bone defects in the maxillofacial region. The composition of the biomaterial includes high-molecular chitosan, chondroitin sulfate, hyaluronate, heparin, alginate and inorganic nanostructured hydroxyapatite. The purpose of the study is to demonstrate morphological and histological early signs of reconstruction of a bone cavity of critical size. The studies were carried out on 84 white female rats weighing 200-250 g. The study group consisted of 84 subjects in total, 40 in the experimental group and 44 in the control group. In all animals, three-walled bone defects measuring 0.5 x 04 x 05 cm were applied subperiosteally in the region of the angle of the lower jaw and filled in experimental group using lyophilized gel mass of chitosan-alginate-hydroxyapatite (CH-SA-HA). In control animals, the bone cavities were filled with an auto-blood clot after bone trepanation and bleeding. The observation periods are 3.5.7 days, 2.3.4.6.8 and 10 weeks. The control of bone regeneration was carried out using multiple morphological and histological analyses. Results showed that following implantation the chitosan construct actively replaced early-stage defects with the formation of a full-fledged new bone tissue as compared to the control group. Already, by the 7th day morphological analysis showed that formation of spongy bone tissue could be seen. After 2 weeks there was a pronounced increase in bone volume (P<0.01), and at 6 weeks after surgical intervention the closure of the defect was 70-80%, after 8 weeks - 100% without violation of bone morphology with a high degree of mineralization. Thus, the use of modified chitosan after filling eliminates bone defects of a critical size in the maxillofacial region, reveals early signs of bone regeneration, and serves as a promising material in reconstructive dentistry.

Severe COVID-19 alters the biochemical and morphological characteristics of blood cells in a wide variety of ways. To date, however, the vast majority of research has been devoted to the study of leukocytes, while erythrocyte morphological changes have received significantly less attention. The purpose of this research was to identify erythrocyte types that were unique to COVID-19, compare the number of different poikilocyte types, and measure erythrocyte sizes to provide data on size dispersion. Red blood cells obtained from 6 control donors (800-2200 cells for each donor) and 5 COVID-19 patients (800-1900 cells for each patient) were examined using low voltage scanning electron microscopy. We did not discover any forms of poikilocytes that would be unique to COVID-19. Among COVID-19 patients, we observed an increase in the number of acanthocytes (p=0.01) and a decrease in the number of spherocytes (p=0.03). In addition, our research demonstrates that COVID-19 causes an increase in the median (p=0.004) and interquartile range (p=0.009) when assessing erythrocyte size.

Scientists, politicians, and practitioners are debating the current structure of pig farms in Lithuania, as medium and small farms have almost disappeared over the past decade. The debated problem is whether the revitalization of medium and small pig farms would sustainably contribute to self-sufficiency in pork? Therefore, this research aims to determine which farms in terms of size could be the most perspective. In order to achieve this aim the multi-criteria evaluation method TOPSIS was used. The economic, production and environmental indicators of Lithuanian pig farms and pig farming sector in Lithuania and selected EU countries: Latvia, Estonia, Poland, Germany, and Denmark were analyzed in this research. The multi-criteria evaluation led to the conclusion that Danish pig farms were the best managed. Germany occupied the second place. The industrial large farms were found as dominated in those countries. Large pig farms (approximately two thousand sows) appeared most perspective in Lithuania: they took the first place in the years examined (2016–2021). The criterion estimate of their assessed indicators was much higher than of the medium (100 sows) and small (20 sows) farms. The main reasons: significantly higher labour productivity, lower cost, lower price, and better production indicators.

Network neuroscience delves into comprehending the intricate arrangement and interactions within the neural networks of the brain. By merging insights from both neuroscience and network theory, it investigates the brain's structure and function through the lens of interconnected nodes (symbolizing brain regions) and edges (symbolizing the connections among these regions) forming a dynamic network. Graph metrics play a pivotal role in neuroscience by providing quantifiable insights into the intricate connectivity patterns within the brain's neural networks. Frequently, nodes are extracted from functional or structural atlases, which can lead to diverse shapes and sizes. Nevertheless, our understanding of how these differing node characteristics and definitions impact the computed graph metrics in neuroimaging data remains limited. This study adopts a data-driven methodology to delineate functional nodes, subsequently examining the influence of their sizes on resultant graph metrics. By employing the Neuromark framework, an entirely automated independent component analysis (ICA) is applied to resting state fMRI data. Through this, functional network connectivity (FNC) matrices are computed—capturing Pearson correlations between component-time courses—while employing a proportional threshold to streamline node connections based on these correlations. Subsequently, various global and local graph metrics are computed, offering insights into network characteristics. Global metrics provide an overarching summary of the network structure, while local measures delve into structural intricacies at the individual component level. Node sizes are computed based on voxel counts surpassing a designated threshold. Next, we calculated the Pearson correlation between the obtained node sizes and the graph metrics, which we term 'node-metric coupling' (NMC). Our findings revealed consistent and noteworthy correlations between the values of graph metrics and the dimensions of brain nodes. To delve deeper into the implications of this correlation, we examined the node-metric coupling within a dataset comprising Alzheimer's disease, mild cognitive impairment, and control subjects. The disparities observed in node-metric coupling among these groups underscore the necessity of accounting for this factor during analysis. The two principal outcomes of this study are as follows: Firstly, the substantial interplay between varying node sizes within a given atlas and the resultant graph metrics; and secondly, the potential utility of node-metric coupling as a viable biomarker for brain disorders. These discoveries hold significant ramifications. While comparing studies employing diverse atlases is already a challenge, our work highlights an additional, critical source of variability: accounting for node sizes. Consequently, the association between intra-atlas node size and graph metric should be thoughtfully acknowledged in future neuroimaging investigations.

Inbreeding depression is expected to be more pronounced in fitness-related traits, such as pig litter size. Recent studies have suggested that the genetic determinism of inbreeding depression may be heterogeneous across the genome. Therefore, the objective of this study is to conduct a genomic scan across the pig autosomal genome to detect the genomic regions that control inbreeding depression for litter size in two varieties of Iberian pigs (Entrepelado and Retinto). The datasets consist of 2,069 (338 sows) and 2,028 (327 sows) records for litter size (Total Number Born and Number Born Alive) for the Entrepelado and Retinto varieties. All sows were genotyped using the Geneseek GGP PorcineHD 70 K. We employed the Unfavorable Haplotype Finder software to extract runs of homozygosity (ROHs) and conducted a mixed model analysis to identify highly significant differences between homozygous and heterozygous sows for each specific ROH. A total of 8 genomic regions located on SSC2, SSC5, SSC7, SSC8, and SSC13, were significantly associated with inbreeding depression, housing some relevant genes such as FSHR, LHCGR, CORIN, AQP6, and CEP120.

Morphological study of lakes defines the sensitivity of their watershed. Moreover, it plays important role in safeguarding the lake’s ecosystem services through proper planning and utilization of the lakes’ resources. In the last few decades, the morphology of lakes in Ethiopian and Kenyan Rift (EKR) valley are experiencing contradicting morphological changes. Being in the same system, some are shrinking and others are expanding beyond their natural boundaries. The objective of this review is to shed light on the trends in spatio-temporal water level fluctuation and their contributing factors for lakes to the academia and decision makers. Peer reviewed article journals, conference proceedings, thesis, and book chapters collected from online sources and supplied by authors on request formed a database of 346 documents where 226 are critically assessed. The review indicated that lakes in Ethiopian rift are shrinking and expanding, while Kenyan lakes are expanding. The en-dorheic lakes suffered the most fluctuations due to anthropogenic factors at the expense of loss of forest and woodlands in their watershed. While the lakes’ water quality related to the morphological changes are given less attention, the predicted 12 m drop of Lake Turkana due to projects in the Omo catchment did not materialize.

The interactions of metal ions with fulvic acids resulted in changes in the particle size and charge. Particle size distribution was trimodal for fulvic acids, bimodal for fulvic complexes with calcium and magnesium, and copper-fulvic complexes had only one size fraction. The compensation of negative charge of carboxylic and phenolic functional groups by positive charged metal ions resulted in the increase in zeta potential which was getting closer to zero in the case of copper-fulvic complexes. However, all metal humic complexes behaved as colloidally unstable which resulted in visually observable sedimentation. Calorimetric measurements provided positive values of changes in enthalpy which indicated endothermic processes. In contrast quantum chemical calculations as well as experiments with model compounds provided negative values indicated exothermic processes. Changes in Gibbs energy were determined as negative and changes in entropy as positive which meant spontaneous processes.

The production of anatase titanium dioxide particles plays a crucial role in the sulfate process used for manufacturing white pigment. A key factor in improving the quality of white pigments is enhancing the thermal mixing process within the precipitation tank. This improvement ensures the uniform dispersion of seed particles instead of their agglomeration, leading to the formation of particles with uniform sizes. The objective of this study was to enhance three-phase CFD simulations involving the mixing process of H₂SO₄ solution, steam as a gas phase, and solid seed particles. By analyzing the trajectories of the seed particles using CFD, the optimal injection position for the seed particles within the mixing process was determined. Subsequently, lab scale test and real field test were conducted based on the insights gained from the CFD simulations. The particle size distribution of two different types of seed inlets was analyzed and compared using Transmission Electron Microscopy (TEM). The findings of this study demonstrate that the developed multi-phase CFD simulation can be effectively utilized to enhance the precipitation process for the production of anatase titanium dioxide particles.

Crossbreeding in dairy cattle with exotic breeds continues to be an appealing practice to the dairy farmers of Bangladesh. However, there is limited knowledge regarding the impact of crossbreeding on both the physical attributes and milk quality traits of crossbred cattle in Bangladesh. Therefore, the primary objective of this study was to evaluate the impact of crossbreeding Bangladeshi local cattle with the exotic Holstein breed on their body characteristics and milk quality. To achieve the goal, data pertaining to body traits and milk samples were gathered from a total of 981 cows from 19 dairy farms located in the northwestern region of Bangladesh. A trained evaluator measured body condition score (BCS), udder score, locomotion score, and body conformation traits. Milk yield information was acquired from official records, while milk composition details were determined through milk analysis. The average measurements for body traits were as follows: wither height (WH) at 138 cm, body length (BL) at 155 cm, and heart girth (HG) at 203 cm. Notably, crossbred cows (Holstein x Local cattle) exhibited greater values for WH, BL, HG, BCS, and udder score than their Bangladeshi local counterparts. Furthermore, the average daily milk yield of sampled cows was recorded at 8.7 kg, with fat and protein contents of 3.78% and 3.67%, respectively. It is worth noting that crossbred cows produced a higher volume of milk compared to Bangladeshi local cattle. However, milk from crossbred cows displayed lower fat and protein content, although their somatic cell score (SCS) remained similar. Additionally, milk from crossbred cows exhibited a longer coagulation time when compared to that of Bangladeshi local cattle. A more comprehensive assessment of the crossbreeding scheme, particularly in comparison to Holstein, would necessitate further research, including an examination of its impact on cheese yield traits, health, fertility, and longevity.

In this work, we report on the first attempt using size-controlled ZnO nanoparticles (NPs) to analyze role of thioacetamide (TAA) in forming ZnS nanostructures from ZnO. The size-controlled B(blue)_, G(green)_, Y(yellow)_ZnO QDs, and NC (nanocrystalline)_ZnO NPs were synthesized by sol-gel process as well as hydrothermal method, respectively and then reacted with an ethanolic TAA solution as sulfur source. After reacting with TAA, the formation of ZnS QDs was observed over time. The chemical reactions were identified using X-ray diffraction (XRD), Transmission Electron Microscope (TEM), UV-vis spectroscopy, and Photoluminescence (PL). All results indicate that ZnS formation is due to direct crystal growth and/or chemical conversion of ZnO to ZnS. Our results enable a broader understanding of the synthetic mechanisms involved in the use of TAA as a sulfur source in forming ZnS nanostructures from ZnO.

This study aims to explore the differences between loess and landslide deposits, focusing on as-pects such as particle distribution, consolidation characteristics, and dynamic shear modulus. Through a series of experiments, the research reveals the similarities and differences between these two entities, yielding several key findings. Firstly, the process of landsliding disrupts the original structure of the loess, resulting in a reduction in porosity and a densification of the soil. This alteration in structural properties leads to significant disparities in physical attributes be-tween landslide deposits and undisturbed loess. Additionally, the movement and sorting of par-ticles during landslides cause variations in particle size distribution across different sections of the landslide deposits. Secondly, the landslide process not only alters the soil's structure but also changes the particle sizes within the loess. Particle wear and sieving result in the transformation of larger particles into smaller ones, leading to a more uniform particle size distribution. This shift in structure and particle size directly impacts the consolidation characteristics of landslide deposits, resulting in a substantial reduction in compression coefficient. Despite undergoing consolidation for decades, the middle and lower sections of landslide deposits still exhibit un-der-consolidation. Although the differences in the maximum dynamic shear modulus between loess and landslide deposits at varying depths are relatively minor, differences in porosity and consolidation characteristics lead to faster decay rates of the dynamic shear modulus for the lat-ter. The study also highlights a reduction in the water sensitivity of the maximum dynamic shear modulus within landslide deposits. Based on experimental results, a predictive model is pro-posed, utilizing A and m values to estimate the maximum dynamic shear modulus of both loess and landslide deposits. In conclusion, this research uncovers the impact of landslide processes on the structure and properties of loess, providing insightful understanding into the disparities between these two entities.

Earnings management and financial distress are two critical facets of financial management in corporations that have lately been the focus of thorough research from both scholars and practitioners. The purpose of the research is to evaluate the influence of financial distress on the earnings management of companies listed at the NSE during the pre- and post-COVID eras. Multiple linear regression was applied in this study to examine the causal association between earnings management and financial distress. To assess the effect of financial distress on earnings management, the study analyzed data from 37 listed companies during the pre-COVID and post-COVID periods. The methodology also takes into account control factors like firm size, GDP, and inflation. The pre-COVID research indicates a significant positive correlation between financial strain and earnings management. In contrast, the correlation between financial distress and earnings management is not statistically significant in the post-COVID analysis. However, research shows that firm size has a statistically significant negative influence on managing earnings. The results of this study show that smaller firms are more inclined to engage in earnings management during the post-COVID era than bigger ones.

Background: Accurate estimation of dietary intake is challenging. But whilst some progress has been made in high-income countries, low- and middle-income countries (LMICs) remain behind, contributing to critical nutritional data gaps. This study aimed to validate an objective, passive image-based dietary intake assessment method against weighed food records in London, UK for onward deployment to LMICs. Methods: Wearable camera devices were used to capture food intake of eating occasions in 18 adults and 17 children of Ghanaian and Kenyan origin living in London. Participants were provided pre-weighed meals of Ghanaian and Kenyan cuisine and camera devices to automatically capture images of the eating occasions. Food images were assessed for portion size, energy, and nutrient intake, and relative validity of the method compared to the weighed food records. Results: Pearson and Intra-class correlation coefficient of estimates of intakes of food, energy and 19 nutrients ranged from 0.60 to 0.95 and 0.67 to 0.90, respectively. Bland-Altman analysis showed good agreement between the image-based method and weighed food record. Under-estimation of dietary intake by the image-based method ranged from 4 to 23%. Conclusions: Passive food image capture and analysis provides an objective assessment of dietary intake comparable to weighed food records.

Debris flows have generated major disasters worldwide due to their great destructive capacity, which is associated with their high energy levels and short response times. To achieve an adequate risk management of these events, it is necessary to define as accurately as possible the different hazard levels to which the territory is exposed. This article develops a new methodology to estimate this hazard based on the hydrodynamic characteristics of the flow and the granulometry of the sediments that can be mobilized by the flow. The hydrodynamic characteristics of the flow are determined through a mathematical modeling that considers the rheology of non-Newtonian flows and the different volumes of sediments that could be transported during events corresponding to different return periods. The proposed methodology was implemented in the Jamundí River basin (Colombia). The results obtained indicate that in the upper part of this basin there is a low hazard level, while in the lower part of the basin approximately 15% of the affected territory has a medium hazard level and the remaining 85% has a low hazard level. The methodology developed is simple to implement but technically rigorous since it considers all relevant aspects in the generation of debris flows.

Raindrop size distribution (RSD) is an index for reflecting precipitation characteristics. Analyzing the differences of RSD plays an important role in understanding the precipitation microphysical processes and improving quantitative precipitation prediction of radar. In this paper, the RSD data of Dafang (57708) station, Majang (57828) station, and Luodian (57916) station (with an altitude of 1722.7m, 985.0m, and 441.5m, respectively) in Guizhou are analyzed according to the precipitation microphysical characteristics. First,Particles with particle size less than 1mm contributes the highest value to the density of particle number , and decrease with the descending altitude. Second, the GAMMA distribution fit shows a better fit compare to M-P distribution fit, and GAMMA distribution fit increases with the ascending altitude. Third, the mass-weighted average diameter is not sensitive enough to the change of precipitation intensity with correlation coefficients of 54.84%, but there is a obvious relationship between the average volume diameter and the precipitation intensity with correlation coefficients of 69.15%. Then, the precipitation prediction model is established using LSTM neural network after fusing the representative microphysical characteristics of RSD with radar and rain gauge data. The precipitation prediction model is applied to the Dafang (57708) site to predict precipitation for time range of 0-180 minutes, and it is found that for the prediction of convective cloud and stratiform cloud precipitation, the 60-minute prediction results are the most consistent with the actual precipitation, where the correlation coefficients are 92.87% and 92.57%, respectively. Conclusively, the results demonstrate that combining with the RSD base data could improve the reliability of precipitation forecasting.

Nanoparticles are of great importance for various scientific and technological applications, drug discovery, ecology, molecular biology, etc. Size is a basic characteristic of any particle, and dynamic light scattering is beyond competition when measuring particle size in dispersions ranging from nanometers to micrometers. Unfortunately, this method has a serious problem in processing and interpreting experimental data. Instrument noise and polydispersity of the sample lead to the situation when one initial autocorrelation function corresponds to several different particle size distributions. Sometimes these different solutions of the inverse task can be found by changing parameters in the software. Sometimes the scientist cannot be suspicious of possible other solutions, having one result from the program. In this article I demonstrate the problem on model and experimental data using three known programs: CONTIN, the Malvern Zetasizer and DynaLS. I also present my own free program Autocor, which allows to test our own hypotheses about the modality and shape of the particle size distribution by optimizing the parameters of our own models with a small number of degrees of freedom.

It is known that complexes based on natural polysaccharides are able to eliminate bone defects. Prolonged hyperglycemia means low bone regeneration and a chronic inflammatory response. The purpose of the study was to increase the efficiency of early bone formation in a cavity of critical size in diabetes mellitus in the experiment. The polyelectrolyte complex contains high molecular ascorbate of chitosan, chondroitin sulfate, sodium hyaluronate, heparin, adgelon serum growth factor, sodium alginate and amorphous nanohydroxyapatite (CH-SA-HA). Studies were conducted on 5 groups of white female Wistar rats: group 1 - regeneration of a bone defect in healthy animals under a blood clot; group 2 - regeneration of a bone defect under a blood clot in animals with diabetes mellitus; group 3 - bone regeneration in animals with diabetes mellitus after filling the bone cavity with a collagen sponge; group 4 - filling of a bone defect with a CH-SA-HA construct in healthy animals; Group 5 - filling of a bone defect CH-SA-HA in animals with diabetes mellitus. Implantation of the CH-SA-HA construct into bone cavities in type I diabetic rats can accelerate the rate of bone tissue repair. The inclusion of modifying polysaccharides and apatite agents in the construction may be a prospect for further improvement of the properties of implants.

Soybean are vulnerable to drought and temperature increases potentially induced by climate change. The purpose of this study was to determine if the use of cover crops (CC) can influence the gas exchange potential of glyphosate tolerant soybean when the vapor pressure deficit (Vpd) increases. This two years study was conducted in an open experimental field comprising Direct Seeding plots without CC (DS) or with CC (DSCC). Stomatal conductance (Gs) was measured five times on the same identified leaves following GBH application. These leaves were then collected in order to observe the stomata (size, density and stomatal index) with a scanning electron microscope and to perform measurements on foliar traits (venation density, width of midrib). The Vpd was calculated concomitantly to Gs measurements at the leaf surface. The results suggest that the use of CC promotes phenotypic change in soybean leaves (more elaborate venation and a higher stomatal density), which in turn may enhance their tolerance to drier conditions. In 2019, Gs could be up to 29% higher in DSCC plots compared to DS ones along with similar Vpd values. This study shows that the benefits of using CC can be observed through the morphological development strategies of the crop plants and their higher tolerance to drought.

Why do the eyes remain comparatively large whereas the cornea is reduced in most troglobiont mysids? Are there any important organ size-dependent functions served by non-visual eye rudiments? This issue was approached by measuring eye structures in five troglobiont species of Mysida and two Stygiomysida compared with 14 troglophile and 49 trogloxene Mysida species. The Organ of Bellonci (OB) was found in all Mysida and as first records also in Stygiomysida. The length of OBs increased with individual body length and eye length in four examined species: from postnauplioid larvae to adult stage in a troglophile and a trogloxene mysid species examined; and from juveniles to adults in a troglobiont mysid and a troglobiont stygiomysid. At the interspecific level, eye length was on average 26% shorter at a given body length while the OB was 40% longer at a given body length and 54% longer at a given eye length, respectively, in adult troglobionts compared with trogloxene mysids. The OB is clearly proliferating while the cornea is reduced in troglobionts. This points to sensory functions (possibly together with other functions). The sensory pore organ was found in all 15 Mysida species whose eyes were mounted on slides, and a first record of this organ was also found in Stygiomysida.

Polyaniline or PANI is a conductive polymer (CPs) with flexibility in turning into conducting properties. The drawback is mainly in terms of limited mechanical properties improvement which attracted the interest in fabrication of PANI with other polymeric materials. PANI-PVL composites film was synthesized and fabricated in this work with chronological steps according to the objectives aligned in two different phases. The first phase determines the optimum parameters to synthesize nanosized PANI. The ideal initial molar ratio, r was 1, stirring speed of 600 rpm, purified by filtration, synthesis temperature of 25 oC, washed by dopant acid, acetone and distilled water. The usage of non-ionic surfactant, Triton X-100 (TX100) with 0.1 % concentration favours the formation of smaller particle size of PANI and good dispersibility compared to the usage of anionic sodium dodecyl sulphate (SDS). The synthesis of PANI in nanosized dimension has the potential to be applied for antimicrobial applications such as gloves and antimicrobial coating of frequent contact points in the near future.

When developing bone implants Young's modulus is one of the primary characteristics of the material that should be considered. The study focuses on the possibility of regulating the modulus of the alloy Ti-50.8 at % Ni by varying its initial structure as well as aging-induced microstructure in a wide range. Microstructure observations were performed using TEM and SEM observations. The calorimetric studies of martensitic transformations were carried out using "Mettler Toledo 822e". Tensile tests were performed in a test temperature range of ‒196≤T≤+100°C using an «IN-STRON 5966». The grain/subgrain size of B2-austenite strongly affects the modulus magnitude. This effect is ambiguous for a material with a grain size of 0.13–3 µm and depends on the test temperature. The effectiveness of aging on the modulus reduction depends on the initial structure: it is most pronounced in an alloy with a relatively coarse grain size of 9 µm and brings a decrease by 3.8 times at a temperature of 37°C. Bone-like elastic modulus (10–30 GPa) at a human body temperature of 37°C is realized in an aged fine-grained NiTi alloy. An ultrafine-grained sub-structure exhibits he same values of Young's modulus in the temperature range from -100°С to 25°С.

Repetitive elements are a major component of DNA sequences due to their ability to propagate through the genome. Characterization of Metazoan repetitive profiles is picking up, however, current pipelines are failing to identify a significant proportion of divergent repeats in non-model organisms. The order Decapoda, for which repeat content analyses are largely lacking, is characterized by extremely variable genome sizes that suggest an important presence of repetitive elements. Here we developed a new standardized pipeline to annotate repetitive elements in non-model organisms, which we applied on 20 Decapoda and 6 other crustacean genomes. With our new tool we identify 10% more repetitive elements than standard pipelines. Repetitive elements were more abundant in Decapoda species than in other crustaceans, with an incredibly large number of highly repeated satDNA families. Moreover, we demonstrated a high correlation between assembly size and transposable elements and a different repeat dynamics between Dendrobranchiata and Reptantia. The patterns of repetitive elements largely reflect the phylogenetic relationships of Decapoda and the distinct evolutionary trajectories within Crustacea. In summary, our results highlight the impact of repetitive elements on genome evolution in Decapoda and the value of our novel annotation pipeline, which will provide a baseline for future comparative analyses.

The mobile payment has been emerging as an alternative to cash and credit cards and is rapidly evolving around the world. This study integrated the general model of innovation diffusion theory (IDT) with the technology acceptance model (TAM) to examine the impact of near-field-communication (NFC) mobile payment environment on the restaurant operating performance (ROP). This paper used convenience sampling to distribute questionnaires to restaurant owners and managers in order to investigate the impact of NFC mobile payment environment on ROP. A total of 279 valid questionnaires were collected. The empirical results show that sales growth, cost saving, flexibility, accessibility and trust &amp; safety had significantly positive impacts on ROP. After considering the restaurant size as a moderator for analysis, there are only two constructs- accessibility and trust &amp; safety had significant impacts on ROP. This empirical finding could provide restaurateurs with a reference to improve ROP by increasing the mobile payment environment.

Loess is a special soil with high water sensitivity, which covers a large area in northwest China. Cracks are prone to generate in loess under the arid and semi-arid climate, which will provide the preferential channel for water and reduce the mechanical properties of soils. It is of great significance to understand the evolution characteristics and mechanisms of the cracks in loess areas. At present, the researches on cracks in soils are mainly concentrated in the characteristics of different cracking patterns. However, the spacing cracks are mostly discussed in materials like rock and concrete, rather than soils. The cracking characteristics and mechanisms of spacing cracks in loess is still inadequate. In this research, the drying tests of loess are carried out with different sizes of specimens. The parameters of spacing cracks and local strain distributions of the loess samples are obtained via PCAS and DIC methods during desiccation, respectively. The cracking modes, space cracking laws like insertion and saturation of spacing cracks are revealed. Finally, the size effect on the characteristics of spacing cracks is verified with a discrete element software MatDEM.

The major goal of this work is to present a novel fractional temperature-dependent boundary element model (BEM) for solving thermoelastic wave propagation problems in smart nanomaterials. The computing performance of the suggested methodology was demonstrated by using stable communication avoiding S-step – generalized minimal residual method (SCAS-GMRES) to solve discretized linear BEM systems. The benefits of SCAS-GMRES are investigated and compared to those of other iterative techniques. The numerical results are graphed to demonstrate the influence of fractional, piezoelectric, and length scale characteristics on total force-stresses. These findings also demonstrate that the BEM methodology is practical, feasible, effective, and has superiority over domain methods. The results of the present paper help to develop the industrial uses of smart nanomaterials.

This paper aims at trying to answer the question of whether a low cost drone equipped with a regular camera can serve as a simple device to estimate the size of objects. Ad-ditionally, it assesses if the accuracy of measurement is good enough for using a drone for measurements, relying solely on GPS position and camera. A review of the literature pertaining to ground object measurements was conducted. The availability of such in-struments was evaluated in terms of purchase and rental costs, the number of instru-ments on the market, and the time to obtain them. The most common measurement methods were considered and their unit costs were reviewed. The cost of professional surveying and measuring equipment was compared to the possibility of using low-cost, non-commercial drones to measure objects and surfaces. The quality of the images ob-tained was compared with high-resolution satellite systems. Is an ordinary drone with a standard camera suitable for length measurement without professional measuring equipment? Should the results be considered only in the category of size estimation?

Tree growth is under the combined influence of abiotic and biotic factors. Trees with different sizes may respond differently to these factors, implying that tree heterogeneity in tree size may also modulate the overall growth trend. To test this hypothesis, we focused on the radial growth trends of natural subalpine forests on the Tibetan Plateau. We first extended the iterative growth model (IGM) to the tree-ring scale (IGMR) to test the applicability of the generalized metabolic growth theory to tree growth. As predicted by the IGMR, the radial growth of trees at the aggregate scale is constrained by a unimodal pattern. Using the IGMR, we reconstructed the historical best growth trajectory (HBGT) of trees within the same community based on the tree with the largest radius and/or longest age in the community. From the average difference between the HBGT and the current radial growth rate of trees with different sizes, we constructed an indicator that can measure the overall variation in tree radial growth. Based on this indicator, we found a negative effect of tree size heterogeneity on the overall variability of tree growth across elevations. Further analysis also revealed that the radial growth rate of trees on the Tibetan Plateau has increased significantly compared to the past, where growing season average temperature and annual minimum temperature were negatively and positively correlated with tree growth below and above the treeline, respectively. Our study not only confirmed that the overall variability of tree growth depends on tree size heterogeneity but also proposed an indicator that reveals net changes in tree radial growth rate relative to the past. These theoretical advances facilitate the understanding of changes in the extent of subalpine forests.

The binding affinity of trastuzumab and pertuzumab to HER2 has been studied using both experimental and in-silico methods. The experiments were conducted using the antibodies in their complete IgG form, as used in clinical therapy, and the extracellular domain of the HER2 protein in solution. This approach provides a precise, reproducible, and reliable view of the interaction between them in physiological conditions. Dynamic light scattering and size exclusion chromatography coupled with tetra detection were utilized to characterize the protein complexes, measure their concentrations, and calculate the equilibrium free binding energy, ΔGbind. In addition, PRODIGY, a QSAR-like model with excellent predictive ability, was employed to obtain in-silico ΔGbind estimations. The results obtained indicate that pertuzumab exhibits a slightly higher binding affinity to HER2 than trastuzumab. The difference in binding affinity was explained based on the contribution of the different interfacial contact (IC) descriptors to the ΔGbind value estimated by the PRODIGY model. Furthermore, experiments revealed that the pertuzumab IgG antibody binds preferentially to two HER2 proteins, one per Fab fragment, while trastuzumab mainly forms a monovalent complex. This finding was interpreted based on a geometrical model that identified steric crowding in the trastuzumab-HER2 complex as compared to the pertuzumab-HER2 complex.

The size of seeds is particularly important for agricultural development, as it is a key trait that determines yield. It is controlled by the coordinated development of the integument, endosperm, and embryo. Large seeds are one of the important ways to improve the ultimate “sink strength” of crops, providing more nutrients for early plant growth and showing certain tolerance to abiotic stresses. There are several pathways for regulating plant seed size, including the HAIKU (IKU) pathway, ubiquitin-proteasome pathway, G (Guanosine triphosphate) protein regulatory pathway, mitogen-activated protein kinase (MAPK) pathway, transcriptional regulators pathway, phytohormone regulatory pathways including auxin, brassinosteroid (BR), gibberellin (GA), jasmonic acid (JA), cytokinin (CK), Abscisic acid (ABA), and MicroRNAs (miRNAs) regulatory pathway. This article summarized the seed size regulatory network and prospected ways to improve yield. We expect to provide valuable reference to researcher in the related field.

Blast charge initiation procedures have a significant impact on both mining safety and production rates. In this study, the inventory benefit of an electric initiation system was investigated to assess its influence on both fragmentation and blast-induced damages. The Wipfrag software's was used to examine the size distribution and productivity of 12 small-scale blasts initiated by both non-electric and electric detonators. All blast rounds was initiated with plain type of electric and NONEL detonators. The average burden, spacing, stemming length, and charge weight were, respectively, 0.85 m, 1.10 m, 0.66m, and 1.1kg. The results showed that the mesh through which 80% of the blast fragments will pass for the electric blast is smaller than the mesh through which the material products from the NONEL blast will pass. The results also demonstrate that the generated blast-induced ground vibration (PPV) from all blast rounds for electric blast varies from 0.4–1.2 mm/s and 80–105dB, while that for non-electric blast ranges from 0.05–0.2mm/s and 72–95dB. As a result, the electric blast initiation technique was found to produce good fragmentation, with a higher percentage of optimum fragment sizes on spec than non-electrically initiated blasts.

This study examines the effects of particle size and heat pipe angle on the thermal effectiveness of a cylindrical screen mesh heat pipe using silver nanoparticles as the test substance. The experiment investigates three different particle sizes (30nm, 50nm, and 80nm) and four different heat pipe angles (0°, 45°, 60°, and 90°) on the heat transmission characteristics of the heat pipe. The results show that the thermal conductivity of the heat pipe increased with an increase in heat pipe angle for all particle sizes, with the highest thermal conductivity attained at a 90° heat pipe angle. Furthermore, the thermal resistance of the heat pipe decreased as the particle size decreased for all heat pipe angles. The thermal conductivity measurements of the particle sizes - 30, 50, and 80 nm - were 250 W/mK, 200 W/mK, and 150 W/mK, respectively. The heat transfer coefficient values for particle sizes 30nm, 50nm, and 80nm were 5500 W/m2K, 4500 W/m2K, and 3500 W/m2K, respectively. The study also found that the heat transfer coefficient increased with increased heat pipe angle for all particle sizes, with the highest heat transfer coefficient obtained at a 90° heat pipe angle.

Background and Aims: Metabolic Syndrome (MetS), a global problem, predisposes to an increased risk for Type 2 diabetes and premature cardiovascular disease. While MetS is associated with central obesity, there is scanty data on adipocyte hypertrophy, increased fat cell size (FCS), in MetS. The aim of this study was to investigate FCS status in gluteal adipose tissue biopsy of patients with nascent MetS without the confounding of diabetes, cardiovascular disease, smoking or lipid therapy . Methods and Results: Fasting blood and subcutaneous gluteal adipose tissue (SAT) biopsy were obtained in MetS (n=20) and controls (n=19). Cardio metabolic features, FFA levels, hsCRP and HOMA-IR were significantly increased in patients with MetS. Waist-circumference adjusted-FCS was significantly increased in patients with MetS and increased with increasing severity of MetS. Furthermore, there were significant correlations between FCS with glucose, HDL-C and the ratio of TG: HDL-C. There were significant correlations between FCS and FFA, endotoxin and monocyte TLR4 abundance. Also, FCS correlated with readouts of NLRP3 Inflammasome activity. Most importantly, FCS correlated with markers of fibrosis and angiogenesis. Conclusions: In conclusion, in patients with nascent MetS, we demonstrate WC-adjusted increase in FCS from gluteal AT that correlated with cellular inflammation, fibrosis and angiogenesis. While these preliminary observations were in gluteal fat, future studies are warranted to confirm these findings in visceral and other fat depots.

The COVID-19 pandemic had a wide-ranging impact, resulting in a global recession due to weakened purchasing power. This circumstance necessitates business organizations adapting to developments and being more conscious of the risk of financial statement fraud. The intention of this research is to investigate the way corporate governance affected financial statement fraud during the COVID-19 pandemic. To acquire empirical data for examining corporate governance variables on financial statement fraud, the research was examined using quantitative methods. The study takes advantage of secondary data acquired from annual reports of companies under special monitoring listed on the Indonesia Stock Exchange of 2020-2021. The logistic regression method was used to evaluate 134 data sets, and financial statement fraud was measured using the Z-Score and F-Score models. The results indicate that using the Z-score, only the board size has a negative effect on financial statement fraud during the COVID- 19 pandemic. Meanwhile, using the F-Score, the corporate governance variables studied are not proven to have an influence on financial statement fraud during the COVID 19 pandemic.

This study describes a comparative in vitro study of the toxicity behavior of zinc oxide (ZnO) nanoparticles and micro-sized particles. The study aimed to understand the impact of particle size on ZnO toxicity by characterizing the particles in different media, including cell culture media, human plasma, and protein solutions (bovine serum albumin and fibrinogen). The study used various techniques such as atomic force microscopy (AFM), transmission electron microscopy (TEM), and dynamic light scattering (DLS) to characterize the particles and their interactions with proteins. Hemolytic activity, coagulation time, and cell viability assays were used to assess ZnO toxicity. The results highlight the complex interactions between ZnO NPs and biological systems, including their aggregation behavior, hemolytic activity, protein corona formation, coagulation effects, and cytotoxicity. Moreover, the study indicates that ZnO nanoparticles are not more toxic than micro-sized particles, and the 50 nm particles resulted in general the least toxic. Furthermore, the study found that at low concentrations, no acute toxicity was observed. Overall, this study provides important insights into the toxicity behavior of ZnO particles and highlights that no direct relationship between nanometer size and toxicity can be directly attributed.

Our previous studies showed pure blue (B) spectra from LEDs can promote shade avoidance responses (SARs). However, it is unknown whether SARs vary among different peak wavelengths (λpeak) of B or how they compare with other photomorphologically-important wavebands, such as ultraviolet-A and far-red. To answer these questions, mustard (Brassica juncea, ‘Ruby Streaks’) and arugula (Brassica eruca, ‘Rocket’) seedlings, grown to the cotyledon unfolding stage under the following narrowband spectrum treatments: UVA (λpeak = 385 nm), B1 (λpeak = 404 nm), B2 (λpeak = 440 nm), B3 (λpeak = 455 nm), and FR (λpeak = 730 nm). Both red (R, λpeak = 660 nm) and dark (D) were used as control treatments. The spectrum treatments were provided at 50 μmol m−2 s−1 on a continuous basis. There were no differences among the B treatments except for reduced mustard fresh weight (FWt) in B3. Compared with R, the B treatments promoted hypocotyl elongation, reduced cotyledon size, and increased petiole length in arugula and B1 increased petiole length in mustard. Compared with the B treatments, UVA inhibited hypocotyl and petiole elongation, similar to or greater than R in both species. Compared with the other LED treatments, seedlings grown under FR generally had the lowest hypocotyl and petiole elongation and the smallest cotyledons. Compared to the LED treatments, D substantially promoted hypocotyl elongation and reduced cotyledon size, except compared to FR in arugula. Among the spectrum treatments, the three B treatments had the greatest SAR promotion effects in both species. Despite having the lowest phytochrome activity, FR inhibited SARs normally associated with high FR environments. Legacy parameters used to estimate SAR-promoting effects of spectrum treatments may not be appropriate for characterizing narrowband spectra from LEDs – new approaches must be developed.

In current study, the production of microparticles from fifteen commercial sugarcane pulp (SCP) lunch-boxes into different types of food under different conditions was investigated, where we used DI water, 4% HAc, and 95% EtOH to simulate aqueous, acidic, and fatty foods. Results showed that compared with DI water and 95% EtOH, 4% HAc caused the degradation of sugarcane fibers, resulting in the highest number of microparticles released, which was significantly greater than the specified limit value. It was estimated that consumers might intake a total number of 36,400 ~ 231,700 items per meal per lunch-box, of which the proportion of microparticles with particle size between 100 ~ 500 μm was the largest, with a number of 12,376 ~ 130,795 items. Moreover, of all SCP lunch-box except S-11, Al and Fe are the main metals, ranging between 35.16 ~ 1244.04 and 44.71 ~ 398.52 mg/kg, respectively, followed by Pb, Ti, and Sr. Interestingly, unlike other lunch-boxes, the content of Pb in S-11 was the highest, with a number of 136 mg/kg. This study provides important information that the safeness including both the production of microparticles and the metallic elements should be considered for SCP lunch-boxes when in contact with food.

Micro-nano-plastics (MNPs) are an important constituent of atmospheric aerosol. However, there is still no standard procedure for their sampling and size fractionation, which is an obstacle to the aggregation and critical analysis of results obtained by different research groups. This review focuses on the sampling and fractionation methodologies used for MNPs. Moreover, a straightforward optimized methodology for the sampling and fractionation is proposed.

X-band dual-polarization phased array radar (XPAR-D) possesses high temporal-spatial resolutions and plays a significant role in detecting meso- and micro-scale convective systems. However, the precipitation attenuation it endures necessitates an effective correction method. This study selected radar data from XPAR-D at the peak of Maofeng Mountain in Guangzhou during May 16-17, 2020 from three precipitation stages after quality control. Attenuation coefficients are calculated for different precipitation types through scattering simulations of raindrop size distribution (RSD) data. Drawing upon this, an attenuation correction algorithm (MZH-KDP method) is proposed for radar reflectivity factor (ZH) according to different raindrop types, and is compared to the ZH-KDP method currently in use. The results indicate that the attenuation amount of XPAR-D echoes depends on the attenuation path and echo intensity. When the attenuation path is shorter and the echo intensity is weaker, the amount of attenuation and correction is smaller. Difficulties arise when there are noticeable deviations in such a situation, which are challenging to solve via attenuation correction methods. Longer attenuation paths and stronger echoes highlight the advantages of the MZH-KDP method, while the ZH-KDP method tends to overcorrect the bias. The MZH-KDP method outperforms the ZH-KDP method for different precipitation types. The superior correction capability of the MZH-KDP method provides a significant advantage in improving the performance of XPAR-D for the detection of extreme weather.

The paper presents the first retrievals of clean snow properties using spaceborne hyperspectral The Environmental Mapping and Analysis Program (EnMAP) observations. The location close to the Dome C in Antarctica has been selected. At this location the atmospheric effects except molecular light scattering and absorption are weak and the simplified atmospheric correction scheme can be applied. The ice grain size, snow specific surface area and snow spectral and broadband albedos have been retrieved using single view EnMAP measurements. In addition, we propose the technique to retrieve trace gas concentrations (e.g., water vapor, ozone) from EnMAP observations over the snow surfaces. Close correspondence of satellite and ground measured parameters has been found.

Comminution is a very important and result-determining step in mineral processing. This is because further downstream processes in the beneficiation chain depend entirely on it. Comminution includes the blasting, crushing, and grinding of ore to liberate valuable mineral particles. It consumes most of the energy used in mineral processing plants with grinding using up to 50% of the provided energy. Tumbling mills are an old technology that is still commonly used for grinding. One of the most used tumbling mills is the ball mill. This paper reviews different types of grinding media that have been developed and improved over the years and their properties. Also reviewed are the effects of grinding media on various aspects such as energy consumption, mill efficiency, minerals liberation and grinding rate. A comparison of the grinding media is given together with the knowledge gaps that still need to be bridged to improve the quality and performance of grinding media used in ball mills. Despite various research conducted on ball mills, the grinding process is still a very energy inefficient process. This creates a great opportunity for further research to improve the process because just a slight improvement in the process efficiency significantly reduces the production costs and provides a lot of environmental benefits.

The history of agricultural terraces dates back to agricultural society; and throughout history, they have enabled agricultural activities to be carried out on lands with irregular relief. They have also served as an essential element of rural landscapes due to their architectural features, building materials, and techniques, as well as the landscapes they create. Furthermore, terraces also contribute to soil conservation by preventing erosion, adding organic matter to the soil, and harvesting rainwater. The significance of agricultural terraces in the cultural landscape has triggered the need to define and classify them. In this regard, agricultural terraces across many different locations have found their place on the List of Globally Important Agricultural Heritage Sites (GIAHS) and UNESCO cultural heritage lists. In the present study, the agricultural terraces of the Erikli neighborhood of the Uzundere district were mapped through surveys, drone shots, and orthophotos, and analyzed based on the size and density indices previously used in the classification of Alpine terraces. The study is important in terms of demonstrating the use of drone technology in mapping agricultural terraces. The results of the study revealed that 51.6% of the agricultural terraces in the study area had very steep slopes and 22195 meters of total stone wall length, the average density index was 523.29 m/ha, and 76.4% of the terraces were meso and macro in character. Moreover the study shows that the terraces in the region are more susceptible to deterioration.

GaN-based micro-size light-emitting diodes (µLEDs) have a number of appealing and distinctive benefits for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, less self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is the serious barrier for applications of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as well as the optimization techniques for improving the EQE of µLEDs.

Features of nanosecond discharge development in a non-uniform electric field are studied experimentally. High spatial resolution imaging showed that thin luminous tracks of great length with a cross-section of a few microns are observed against the background of discharge glow in air and argon. It has been established that the detected tracks are adjacent to brightly luminous white spots on the electrodes or to the vicinity of these spots, and are associated with the flight of small particles. It is shown that the traces have various shapes and change from pulse to pulse. The particle tracks may look like curvy or straight lines. In some photos, they can change the direction of movement to the opposite. The particle trace was found to abruptly cut off and a bright flash is visible at the trail break point. The color of the tracks differs from that of the spark leaders, while the bands of the second positive nitrogen system dominate in the gap spectra during the existence of a diffuse discharge. Areas of blue light are evident near the electrodes, as well. Development of glow in the gap during its breakdown is revealed using an ICCD camera. Physical reasons for the observed phenomena are discussed.

Remanufacturing is a way for product recovery initiative and maintaining sufficient production flow to satisfy customer demand through circular economy. Recently, manufacturers have been progressively incorporating remanufacturing processes, making their supply chain vulnerable to disruptions. Among the disruptions that usually occur is the shortage in spare parts supply, which causes unexpected delay in production and possible loss of sales. In the face of potential disruption, it is essential for remanufacturing facilities to manage their supply chains in an optimum manner as to decrease the adverse impact of disruptions to their business. In this study, a two-stage production-inventory system is analysed by developing a cost-minimisation model focusing on the recovery schedule after a disruption occurrence in sourcing spare parts for a remanufacturer’s production cycle. The developed model was solved using the branch and bound algorithm. Through numerical experiments, the results indicate that the optimal recovery schedule and the number of recovery cycles are significantly dependant on disruption time, lost sales and backorder costs. Moreover, a sensitivity analysis shows that the lost sales option seems to be more effective than the backorder option in optimising the system’s overall cost. The proposed model could assist managers in deciding the optimal production strategy while providing interesting managerial insights into vital spare parts recovery issues when disruption strikes.

Traditional camera sensors rely on human eyes for observation. However, the human eye 1 is prone to fatigue when observing targets of different sizes for a long time in complex scenes, and 2 human cognition is limited, which often leads to judgment errors and greatly reduces the efficiency. 3 Target recognition technology is an important technology to judge the target category in camera 4 sensor. In order to solve this problem, a small size target detection algorithm for special scenarios was 5 proposed by this paper. Its advantage is that this algorithm not only has higher precision for small 6 size target detection, but also can ensure that the detection accuracy of each size is not lower than the 7 existing algorithm. In this paper, a new down-sampling method was proposed, which could better 8 preserve the context feature information. The feature fusion network was improved to effectively 9 combine shallow information and deep information. A new network structure was proposed to 10 effectively improve the detection accuracy of the model. In terms of accuracy, it is better than: YOLOX, 11 YOLOXR, YOLOv3, scaled YOLOv5, YOLOv7-Tiny and YOLOv8.Three authoritative public data sets 12 were used in this experiment: a) On Visdron data sets (small size targets), DC-YOLOv8 is 2.5% more 13 accurate than YOLOv8. b) On Tinyperson data sets (minimal size targets), DC-YOLOv8 is 1% more 14 accurate than YOLOv8. c) On PASCAL VOC2007 data sets (Normal size target), DC-YOLOv8 is 0.5% 15 more accurate than YOLOv8.

The effect of biotic (e.g., growth characteristics) and a-biotic (e.g., crown closure) factors on cone production, fertility variation and gene diversity was evaluated in two consecutive years in 130 year old natural populations of Taurus cedar also called cedar of Lebanon (Cedrus libani A. Rich.). The a-biotic factors viz., altitude, temperature, aspect and rainfall varied; while some of them can be managed by cultural operations like management of crown and stand density. Impact of crown closure on cone production, fertility variation and related parameters were observed in Taurus cedar’s natural populations sampled from southern Turkey. Maximum cone production of 29 and 40/tree was recorded with full crown closure in two consecutive years by large differences among individuals within crown closure class. For instance, cone productions were between 10 and 67 in full crown closure of first year. The sibling coefficient, which is a measure of the fertility variation in a stand, was the highest (1.16) for full crown closure in the first (meaning 86% fertile trees) and the second year (1.55, 65%), while it was the lowest for medium crown closure (1.09, 92%) in both years. Gene diversity decreased from a degraded patch (0.987) to that with full crown closure (0.984). Results of variance analysis showed significant (p≤0.05) difference between crown closure classes for cone production within second year, and between years. Significant positive (p0.05) correlations were noted between years for cone production (r=0.22), and between cone production and crown closure in first and second years (r=0.29). However, growth characteristics had no effective on cone productions in individual crown closure classes, while there were significant (p0.05) correlations between diameter at breast height and cone production for both years (r= 0.15 and 0.17) in pooled populations.

This review focuses on developments that quantify grain quality with a range of spectral sensors in an on-farm setting. If the application of sensor technologies were expanded and adopted on-farm, growers could identify the impact and manage the harvesting operation to meet a range of quality targets and provide an economic advantage to the farming enterprise.

The interference-fit size has a significant effect on CFRP/Al-alloy laminates riveted lap joints, the requirements for the interference-fit size are different because of the strengthening of heterogeneous materials. However, in the process of the riveted CFRP/Al-alloy, the heterogeneous laminates lead to poor structural strength because of the different requirements of interference-fit size. Therefore, the different assembly types of riveting mold are designed to acquire a novel interference-fit size, and the tensile test is adopted to evaluate the tensile property. In addition, the fracture failure of CFRP/Al-alloy laminates riveted lap joint is observed by the ultra-depth of field microscope. Finally, the best assembly type is the trapezoid riveting mold combined with an arc riveting die, and the sidewall intersection angle of the trapezoid riveting mold is 66° which could achieve a suitable interference-fit size and a better mechanical performance.

Coffee is regarded as the highly consumed beverage throughout the world and has established a key spot in the world economy as an important commodity for trading. In general, they are produced by brewing their roasted and ground beans, which release aromatic coffee; as well as produce an equivalent amount of spent coffee grounds (SCG). Previously, they were discarded as wastes or used as natural pest repellent or garden fertilizer; however, in recent times, are valorized into biofuels owing to their high calorific value. In fact, SCG briquettes have gained wide attention for supplying energy renewably, especially to the rising energy demand; and also have been identified as an effective measure to reduce their pollution. With this in mind, this present chapter focuses on reviewing the availability and chemistry involved in these SCG wastes, pre-treatments and preparations required for their briquetting, compacting techniques followed, and fuel characteristics of their briquettes, from various available works of literature. Here, their availability showcases the amount of SCG wastes generated with respect to time and consumption, wherein understanding their chemistry helps in deciding the pre-treatments necessary for their briquetting. Meanwhile, preparation techniques briefs about the necessary pre-treatments undertaken before compaction by different researchers; and the fuel characteristics define the physicochemical and mechanical properties of their briquettes, developed using various compaction methods. Besides, combustion behaviors of these briquettes are explained in terms of their burning characteristics and emission levels, as reported in literatures; which help in deciding their suitability as a replacement for existing fossil coal. Eventually, all the reported data were in accordance with their permissible standards and suggested these SCG as a highly renewable solid biofuel.

Swimming pools are examples of water-intensive facilities, where solutions for reducing economic and environmental costs are increasingly frequently searched. One of the solutions is the recovery of water from wastewater, including from washings obtained through the process of rinsing filter bed. The study objective was the qualitative and quantitative assessment of post-coagulation sludges, the main pollutant found in the washings. During the analyses, assessment of the sedimentation capabilities of the sludges was performed (gravitationally), particle size distribution was assessed (particle size distribution analyzer) and assessment of phytotoxicity with the use of plant indicators in short-term tests was performed (Lemna minor, Lepidium sativum, Sinapis alba, Raphanus sativus). The samples were collected from two independent circulations, which differed in terms of capacity and type of coagulant used. The tested post-coagulation sludges were characterized by high content of total suspended solids: in samples from Circulation 1 from 251 to 128 mg/l, in Circulation 2 from 489 to 228 mg/l. However, the sedimentation processes enabled significant separation of sludges. The hydrolyzed coagulant contributed to the improvement of sedimentation capabilities of sludges. Despite the fact that in many samples low sludge concentrations favored stimulation of plant growth, the post-coagulation sludges can constitute a hazard to plant growth, particularly in the long-term perspective.

The results of the study of the influence of the size of cylindrical samples of A5N aluminum on the time and rate of their cooling are presented. According to experimental data, the temperature dependence of the heat transfer coefficient for pure metals is calculated. It revealed that the process of cooling of the aluminium and its alloys has a relaxation behavior. It has found that the main mechanisms of natural air cooling are convection heat transfer and radiation. The characteristic cooling time due to radiation is less than due to convection. The contribution of thermal radiation is noticeable at high temperatures. It was found that the characteristic times of cooling due to radiation and convection increase with increase in volume to area ratio of the sample.

Nanopeening treatment was applied to the AISI 420 steel to decrease its sensitivity to the tribocorrosion damage. Microstructural investigation highlighted that the Nanopeening treatment led to a high plastic deformation and nanostructured surface layer with 110 µm depth. . In order to study the combined effect of corrosion and mechanical wear, tribocorrosion tests were performed on non–treated and nanopeened samples in boric acid and lithium hydroxide solution, considering both continuous and intermittent sliding. It was found that the AISI 420 steel is sensitive the synergism between mechanical friction and electrochemical corrosion with a domination of abrasive wear. Adhesive wear was also detected in the wear track. Indeed, the mechanical wear was pronounced under intermittent sliding because of hard wear debris generation from the repassivated layer during rotating time. The Nanopeening treatment led to enhance mechanical performance and corrosion properties. Such improvement could be explained by the high plastic deformation resulting in the nano-structuration of grains and increasing hardness of AISI 420 steel.

In the multicenter, non-randomized, exploratory C-reactive protein (CRP) Apheresis in Myocardial Infarction (CAMI-1) study, CRP apheresis after ST-Elevation Myocardial Infarction (STEMI) significantly decreased blood CRP concentrations in humans. Cardiac damage was assessed by Cardiac Magnetic Resonance (CMR1) 3-9 d after onset of STEMI symptoms and quantified by myocardial infarct size (IS; %), left ventricular ejection fraction (LVEF; %), circumferential strain (CS) and longitudinal strain (LS) Compared with the control group (n=34), cardiac damage was significantly lower in the apheresis group (n=32). These findings suggested improved wound healing due to CRP apheresis already within few days after the STEMI event. In the current supplementary data analysis of CAMI-1, we have tested by a follow-up CMR (CMR2) after an average of 88 (65-177) d whether the effect of CRP apheresis is clinically maintained. After this time period wound healing in STEMI is considered complete. Whereas patients with low CRP production and a CRP gradient cut off of &lt;0.6 mg/L/h in the hours after STEMI (9 of 32 patients in the CRP apheresis group) did not significantly benefit from CRP apheresis in CMR2, patients with high CRP production and a CRP gradient cut off of &gt;0.6 mg/L/h (23 of 32 patients in the CRP apheresis group) showed significant treatment benefit. In the latter patients, CMR2 revealed a lower IS (-5.4%; p=0.05), a better LVEF (+6.4%; p=0.03), and an improved CS (-6.1%; p=0.005). No significant improvement, however, was observed for LS (-2.9%; p=0.1). These data suggest a sustained positive effect of CRP apheresis on the heart physiology in STEMI patients with high CRP production well beyond the period of its application. The data demonstrate the sustainability of the CRP removal from plasma which is associated with less scar tissue.