In the Netherlands, the assessment of existing prestressed concrete slab-between-girder bridges showed that the thin, transversely prestressed slabs may be critical for static and fatigue punching when evaluated using the recently introduced Eurocodes. On the other hand, compressive membrane action increases the capacity of these slabs and changes the failure mode from bending to punching shear. To improve the assessment of the existing prestressed slab-between-girder bridges in the Netherlands, two 1:2 scale models of an existing bridge, the Van Brienenoord Bridge, were built in the laboratory and tested monotonically as well as under cycles of loading. The result of these experiments is: 1) the static strength of the decks, showing that compressive membrane action significantly enhances the punching capacity, and 2) the Wöhler curve of the decks, showing that compressive membrane action remains under fatigue loading. The experimental results can then be used for the assessment of the most critical existing slab-between-girder bridge. The outcome is that the bridge has sufficient punching capacity for static and fatigue loads, and thus that the existing slab-between-girder bridges in the Netherlands fulfil the code requirements for static and fatigue punching.

DC-connected parallel inverter systems are gaining popularity in industrial applications. However, such parallel systems generate excess current ripple (harmonics) at the DC-link due to harmonic interactions between the inverters in addition to the harmonics from the PWM switching. These DC-link harmonics cause the failure of fragile components such as DC-link capacitors. This paper proposes an interleaving scheme to minimize the current harmonics induced in the DC-link of such a system. The results show that when the carrier waves of the two inverters are phase-shifted by 90° angle, the maximum high-frequency harmonic ripple cancellation occurs, which reduces the overall RMS value of the DC-capacitor current.The outcome of this proposed solution is a cost-effective DC-harmonics mitigating strategy for the industrial designers to practically configuring multi-inverter systems, even when most of the drives are not operating at rated power levels. Experimental and simulation results presented in this paper verify the effectiveness of the proposed carrier-based phase-shifting scheme for two different configurations of common DC connected multi-converter systems.

Pure-compression shells have been the central topic in the form-finding of shells. This paper studies tension-compression mixed type shells by utilizing a NURBS-based isogeometric form-finding approach that analyzes Airy stress functions to expand the possible plan geometry. A complete set of smooth version graphic statics tools is provided to support the analyses. The method is validated using examples with known solutions, and a further example demonstrates the possible forms of shells that the proposed method permits. Additionally, a guideline to configure a proper set of boundary conditions is presented through the lens of asymptotic lines of the stress functions.

In this work, we investigate the behaviour of relativistic quantum oscillator under the effects of Lorentz symmetry violation determined by a tensor $(K_F)_{\mu\nu\alpha\beta}$ out of the Standard Model Extension. We analyze this relativistic system under an inverse radial electric field and a constant magnetic field induced by Lorentz symmetry violation. We see that the presence of Lorentz symmetry breaking terms modified the energy spectrum of the system, and a quantum effect arise due to the dependence of the linear charge density on the quantum numbers of the system

We suggest that momentum should be redened in order to help make physics more consistent and more logical. In this paper, we propose that there is a rest-mass momentum, a kinetic momentum, and a total momentum. This leads directly to a simpler relativistic energy momentum relation. As we point out, it is the Compton wavelength that is the true wavelength for matter; the de Broglie wavelength is mostly a mathematical artifact. This observation also leads us to a new relativistic wave equation and a new and likely better QM. Better in terms of being much more consistent and simpler to understand from a logical perspective.

As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

This paper presents several novel designs of underwater portable radio antennas operating in the 2 MHz, 50 MHz and 2.4 GHz bands and efficient for launching surface electromagnetic waves at the seawater/air interface. The antenna operation is enabled by an impedance matching antenna enclosure, which is filled with de-ionized water. Enhanced coupling to surface electromagnetic waves is based on the field enhancement at the antenna tip. These design features allow us to reduce antenna dimensions and improve the coupling of electromagnetic energy to the surrounding saltwater medium. Since surface wave propagation length far exceeds the skin depth of conventional radio waves at the same frequency, this technique is useful for broadband underwater wireless communication over distances, which far exceed the skin depth in seawater. We conclude that the developed broadband underwater radio communication technique will be useful in networking of unmanned underwater vehicles.

Phenomenon of vacuum fluctuations of virtual particles in high energy physics has been mathematically modeled by a third order differential equation. Aim of present theory is to unravel underlying mathematical equation capable of explaining microscopic phenomenon of vacuum fluctuations. Solution of such a differential equation after applying appropriate boundary conditions gives an acceptable wave function i.e. . Operation of energy and time operator on this wave function proves that these operators do not hold commutative property. Time energy uncertainty principle has been derived by calculating variance of energy and time for the same wave function.

The diffraction-like process displayed by a spatially localized matter wave is here analyzed in a case where the free evolution is frustrated by the presence of hard-wall-type boundaries (beyond the initial localization region). The phenomenon is investigated in the context of a nonrelativistic, spinless particle with mass m confined in a one-dimensional box, combining the spectral decomposition of the initially localized wave function (treated as a coherent superposition of energy eigenfunctions) with a dynamical analysis based on the hydrodynamic or Bohmian formulation of quantum mechanics. Actually, such a decomposition has been used to devise a simple and efficient analytical algorithm that simplifies the computation of velocity fields (flows) and trajectories. As it is shown, the development of space-time patters inside the cavity depends on three key elements: the shape of the initial wave function, the mass of the particle considered, and the relative extension of the initial state with respect to the total length spanned by the cavity. From the spectral decomposition it is possible to identify how each one of these elements contribute to the localized matter wave and its evolution; the Bohmian analysis, on the other hand, reveals aspects connected to the diffraction dynamics and the subsequent appearance of interference traits, particularly recurrences and full revivals of the initial state, which constitute the source of the characteristic symmetries displayed by these patterns. It is also found that, because of the presence of confining boundaries, even in cases of increasingly large box lengths, no Fraunhofer-like diffraction features can be observed, as happens when the same wave evolves in free space. Although the analysis here is applied to matter waves, its methodology and conclusions are also applicable to confined modes of electromagnetic radiation (e.g., light propagating through optical fibers).

A series of Ti₄₀Zr₂₅Cu₉Ni₈Be₁₈)_100-xTM_x (x = 0, 1, 2, 3, 4 at.%, TM = Nb, Y) Bulk amorphous alloys were designed and prepared using the copper mold casting method. The microstructures, glass forming ability and mechanical properties of the alloys were investigated by means of X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential scanning colorimetry (DSC), depth-sensitive nanoindentation and uniaxial compressive test. The Bulk amorphous alloys with different ductility were investigated by measuring their plastic deformation energy (PDE) of the first pop-in events during loading. The relationships between the PDE value, shear band formation and ductility in Bulk amorphous alloys have been investigated. The results show that the PDE value decreases by the Nb addition and promotes the generation of multiple shear bands easily, which increase the fracture strength and plasticity significantly. Substituting Nb with Y has exactly the reverse effect. A useful rule for preparing of Bulk amorphous alloys with high plasticity is herein proposed, whereby the chemical composition of the Bulk amorphous alloys can be tailored to possess a lower PDE value.

Four methods in two different families have been constructed to derive the exact solutions to Benjamin-Bona-Mahony equation in two space dimensions. Simply defined hyperbolic tangent, hyperbolic secant and hyperbolic cosecant ansatzes and the expansion method based on the Sine-Gordon equation in two dimensions are directly substituted into the governing ODE reduced from the two dimensional BBM equation. Classical algebraic method is used to find the relations among the target parameters representing the nonzero coefficients in the predicted solutions and the wave transform parameters. Some complex and real solutions have been constructed in explicit forms.

Most fully developed galaxies have vivid spiral structure, but the formation and evolution of spiral structure is still a mystery that is not fully understood in astrophysics. We find that the currently used equations of galactic dynamics contain some unreasonable components. In this paper, the following three working assumptions are introduced to simplify the galactic structural equations. 1. In the research of large-scale structure, the retarded potential of the gravitational field should be taken into account. The propagating time of the gravitational field from center to border is longer than the revolution periods of the stars near the center of galaxy. Newton's gravitational potential is unreasonable for such case, and the weak field and low velocity approximation of Einstein's field equation should be adopted. 2. The stars in a fully developed galaxy should be zero-pressure and inviscid fluid, and the equation of motion is different from that of ordinary continuum mechanics. Stars move along geodesics. 3. The structure of the galaxy is only related to the total mass density distribution. The equation of state of dark halo is different from that of ordinary luminous interstellar matter, so their trajectories are also very different. Dark halo and ordinary matter in galaxy are automatically separated. The total mass density distribution can be presupposed according to the observation data, and then it can be determined by comparing the solution of the equations with the observed data. These assumptions and treatments are supported by theory and observation. The variables of the equations of simplified galactic dynamics are separated from each other, and the equations are well-posed and can be solved according to a definite procedure. Therefore, this simplified dynamic equation system provides a more reasonable and practical framework for the further study of galactic structure, and can solve many practical problems. Besides, it is closely related to the study of dark energy and dark matter.

Extracorporeal shock wave therapy (ESWT) is a safe and effective treatment option for various pathologies of the musculoskeletal system. Many studies addressed the molecular and cellular mechanisms of action of ESWT. However, no uniform concept could be established in this matter until now. We performed a systematic review of the effects of exposure of musculoskeletal tissue to extracorporeal shock waves (ESWs) reported in the literature. The key results were as follows: (i) compared to the effects of many other forms of therapy, the clinical benefit of ESWT does not appear to be based on a single mechanism; (ii) different tissues respond to the same mechanical stimulus in different ways; (iii) just because a mechanism of action of ESWT was described in a study does not automatically mean that this mechanism was relevant to the observed clinical effect; (iv) focused ESWs and radial ESWs seem to act in a similar way; and (v) even the most sophisticated research into the effects of exposure of musculoskeletal tissue to ESWs cannot substitute clinical research in order to determine the optimum intensity, treatment frequency and localization of ESWT.

Layered two-dimensional (2D) graphene oxide (GO) films are integrated with micro-ring resonators (MRRs) to experimentally demonstrate enhanced nonlinear optics in the form of four-wave mixing (FWM). Both uniformly coated and patterned GO films are integrated on CMOS-compatible doped silica MRRs using a large-area, transfer-free, layer-by-layer GO coating method together with photolithography and lift-off processes, yielding precise control of the film thickness, placement, and coating length. The high Kerr nonlinearity and low loss of the GO films combined with the strong light-matter interaction within the MRRs results in a significant improvement in the FWM efficiency in the hybrid MRRs. Detailed FWM measurements are performed at different pump powers and resonant wavelengths for the uniformly coated MRRs with 1−5 layers of GO as well as the patterned devices with 10−50 layers of GO. The experimental results show good agreement with theory, achieving up to ~7.6-dB enhancement in the FWM conversion efficiency (CE) for an MRR uniformly coated with 1 layer of GO and ~10.3-dB for a patterned device with 50 layers of GO. By fitting the measured CE as a function of pump power for devices with different numbers of GO layers, we also extract the dependence of GO’s third-order nonlinearity on layer number and pump power, revealing interesting physical insights about the evolution of the layered GO films from 2D monolayers to quasi bulk-like behavior. These results confirm the high nonlinear optical performance of integrated photonic resonators incorporated with 2D layered GO films.

This study demonstrates the orientation and the ‘shape factor’ have pronounced effects on the development of the localized pressure fields inside of the helmet. We used anatomically accurate headform to evaluate four modern combat helmets under blast loading conditions in the shock tube. The Advanced Combat Helmet (ACH) is used to capture the effect of the orientation on pressure under the helmet. The three modern combat helmets: ECH, Ops-Core, and Airframe, were tested in frontal orientation to determine the effect of helmet geometry. Using the unhelmeted headform data as a reference, we characterized pressure distribution inside each helmet and identified pressure focal points. The nature of these localized “hot spots” is different than the elevated pressure in the parietal region of the headform under the helmet widely recognized as the under-wash effect also observed in our tests. It is the first experimental study which indicates that the helmet presence increased the pressure experienced by the eyes (as evidenced by the pressure sensors in the H8 and H9 locations), and the forehead (denoted as H1 location). Pressure fingerprinting using an array of sensors combined with the application of principle component analysis (PCA) helped elucidate the subtle differences between helmets.

An evanescent wave is a non-propagating wave with an imaginary wave vector. In this study, we prove that these are solutions of the tachyon-like Klein–Gordon equation, and that in the tunneling of ultrarelativistic spin-1/2 particles they describe superluminal states arising from interactions between a particle and barrier. These states decay as a particle emerges from the opposite side of a potential barrier, conserving the same initial energy but not necessarily the same mass. The obtained theory is applied to the neutrino, to explain flavor oscillations during free flight and determine the conditions that maximize the probability of their occurrence.

This paper focuses on parametric model order reduction (PMOR) of guided ultrasonic wave propagation and its interaction with damage in a fiber metal laminate (FML). Structural health monitoring in FML seeks to detect, localize and characterize the damage with high accuracy and minimal use of sensors. This can be achieved by the inverse problem analysis approach which employs the signal measurement data recorded by the embedded sensors in the structure. The inverse analysis requires to solve the forward simulation of the underlying system several thousand times. These simulations are often exorbitantly expensive and triggered the need for improving their computational efficiency. A PMOR approach hinged on the proper orthogonal decomposition method is presented in this paper. An adaptive parameter sampling technique is established with the aid of a surrogate model to efficiently update the reduced-order basis in a greedy fashion. A numerical experiment is conducted to illustrate the parametric training of the reduced-order model. The results show that the reduced-order solution based on the PMOR approach is accurately complying with that of the high fidelity solution.

A novel effective vibrational mode was discovered in the conventional transducer with an array of orthogonal (square) regular piezoelectric rods in 1-3 piezocomposite, containing the damping backing and front matching layers. The operational resonance in the structure was determined as the Surface Acoustic Wave (SAW) on the backing boundary excited by the adjacent piezo-rods, with its frequency typically near 3 times lower the fundamental half-lambda conventional piezocomposite resonance. Pulse-echo sensitivity and transmitting sound-pressure-level (SPL) in air showed that the signal strength is roughly comparable to the industrial similar air transducers at the frequency range 100…700 kHz, where at these frequencies the lateral and longitudinal piezoelement dimensions in the conventional transducer design are typically close to each other causing interference with unwanted coupling modes. As was determined theoretically and proved in experiments, the backing SAW resonance effect in the transducer performance is inherent just to the regular periodic 1-3 piezocomposite structure, and does occur neither with randomly located/oriented piezo-rods, nor in the homogeneous piezo-plate at least with the same lateral cross-section as the connected to it backing. The purpose of the article is to investigate a newly discovered operational vibrational mode of a SAW type in 1-3 regular piezocomposite, other than piezoelectric resonance. The investigated phenomena can improve the transceiver sensitivity, bandwidth, providing lower drive voltage, and smaller and lighter weight ultrasonic transducers. Based on the piezocomposites with thickness’ 1…1.5 mm (rod resonance near 2…3 MHz), pillar width 0.2…0.8 mm, kerf width 0.1…0.4 mm, the transceivers with an operating frequency from 140 kHz to 650 kHz were designed and fabricated with a conventional backing of a mixture of high-density tungsten powder and epoxy, and a matching layer of a mixture of low-density glass bubbles and epoxy. Experimental evaluation of their acoustical performance showed expected characteristics suitable for practical applications.

Fusion device and its structure may be designed by various means. Two of most popular are; weight basis (described in previous study by author) and energy basis. In present research, later method is explored and described. Energy basis is based on amount of energy released from device upon detonation followed by explosion. Its beneficial in a sense that device size can be kept as independent variable as compared to dependent in former case. Further, it shortens the design procedure. For example, heat transfer pattern in such approach directly helps in quantifying wall thickness which dictates material, fabrication, and manufacturing route. It may also eliminate anisotropy as wall thickness is direct function of amount of heat at which it will rupture and can be much thinner. Device geometry can also be flexibility controlled as it is no longer dependent on pay load bay capacity. This allows more freedom in designing subsystems (compartments, their locations, focusing, switches, and mixers). Such devices can be more compact and simpler. Few such design configurations are proposed.

Comparison between hydraulic and hydrologic computational methods is conducted in this study, regarding prismatic open channels under unsteady subcritical flow conditions. One-dimensional unsteady flow continuity and momentum equations are solved using explicit and implicit finite difference schemes for a symmetrical trapezoidal cross section, where the flow discharge and depth are the dependent variables. The results have been compared to those derived from Muskingum-Cunge hydraulic/hydrologic method as well as the commercial software HEC-RAS. The results from explicit and implicit code compare well to those from commercial software and hydraulic/hydrologic methods for long prismatic channels, thus directing the hydraulic engineer to quick preliminary design of prismatic open channels for unsteady flow with satisfactory accuracy.

In the present work a novel, portable and innovative eNose composed of a surface acoustic wave (SAW) sensor array based ZIF-8, and ZIF-67 nanocrystals (pure and combined with gold nanoparticles) as sensitive layers has been tested as a non-invasive system to detect and differentiate disease markers, such as acetone, ethanol and ammonia, related with early diagnosis of diabetes mellitus through exhaled breath. The sensors have been prepared by spin coating, achieving continuous and homogenous sensitive layers. Low concentrations (5 ppm, 10 ppm and 25ppm) of the marker analytes were measured, obtaining high sensitivities, good reproducibility, short time response and fast signal recovery.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.

Monsoon winds drive upwelling along the eastern coast of India during the south-west (SW) monsoons. These winds also provide alongshore windstress (AWS) resulting in positive cross-shore Ekman transport (ET) from late May to the end of September. While instances of high ET and sea surface temperature (SST) based upwelling index (UI_SST) were observed along different parts of the coast, UI_SST was weaker in the northern section in the earlier part of monsoon. This was even in the presence of maximum AWS and ET during the 10 years analysis period spanning January-2009 to December-2018. Additionally, negative sea surface height anomalies (SSHAs), typically associated with coastal upwelling, were observed only along the southern-most coast. An empirical orthogonal function (EOF) analysis revealed two coherent modes of SSHA variation. The first principal component (PC) showed a SSHA signature coincident spatio-temporally with the first downwelling Kelvin wave, closely associated with the equatorial zonal winds that drive coastal Kelvin waves. The third PC with a coastal SSHA pattern similar to the second upwelling Kelvin wave was associated with offshore ET along the northern part of the Indian east coast. Time series of the two PCs exhibited suppression of coastal upwelling by downwelling Kelvin waves during May-July along the northeastern coast of India. Local AWS driven ET was the primary driver of coastal upwelling with the weakening of the remotely forced Kelvin waves in August. A coherent mode consisting of negative coastal SSHA signature was excited in response to local AWS driven ET during the upwelling period. This study examined the spatio-temporal variability of SW monsoon coastal upwelling along the east coast of India and illustrated the role of equatorial windstress forced first downwelling Kelvin wave in suppressing upwelling in the northern part of the coast during early SW monsoon season.

It is well-known that surface plasmon wave propagates along a straight line, but this common sense was broken by the artificial curved light – plasmon Airy beam. In this paper, we introduce a new class of curved surface plasmon wave - the photonic hook plasmon. It propagates along wavelength scaled curved trajectory with radius less than surface plasmon polariton wavelength, and can exist despite the strong energy dissipation at the metal surface.

Complex colloidal fluids, depending on particulates’ shapes and packing fractions, may have a wide range of shear thinning and thickening behaviors. A particular interesting way to transition between different types of such behavior is by infusing functional complex particles that can be manufactured using modern techicques such as 3D printing. In this paper, we display 2D molecular dynamics simulations of such fluids with infused star-shaped functional particles, with variable leg length and number of legs, as they are infused in a non-interacting, coarse-grained fluid. We vary the packing fraction (ϕ) of the system, and for each different system we apply shear with various strain rate that turns the fluid into a jammed state and rise the apparent viscosity of fluid. We demonstrate the dependence of viscosity with the particles’ packing fraction. We show the role of shape and design dependence of the functional particles towards the transition to a shear thickening fluid .

We apply utilized the extended form of the auxiliary equation method to obtain extensively reliable exact travelling wave solutions of perturbed Gerdjikov–Ivanov equation (GIE) that is widely used as a model in the field theory of quanta and non-linear optics. The method is based on a simple first order second degree ODE. The new form of the approach gives more solutions to the governing equation efficiently.

Spaceborne altimeters are an important data source for obtaining global sea surface wind speeds (U10). Although many altimeter U10 algorithms have been proposed and they perform well, there is still room for improvement. In this study, the data from ten altimeters were collocated with buoys to investigate the error of the altimeter U10 retrievals. The U10 residuals were found to be significantly dependent on many oceanic and atmospheric parameters. Because these oceanic and atmospheric parameters are inter-correlated, an asymptotic strategy was used to isolate the impact of different parameters and establish a neural-network-based correction model of altimeter U10. The results indicated that significant wave heights and mean wave periods are effective in correcting U10 retrievals, probably due to the tilting modulation of long-waves on the sea surface. After the wave correction, the root-mean-square error of the retrieved U10 was reduced from 1.42 m/s to 1.24 m/s and the impacts of thermodynamic parameters, such as sea surface (air) temperate, became negligible. The U10 residuals after correction showed that the atmospheric instability can lead to errors on extrapolated buoy U10. The buoy measurements with large air-sea temperature differences need to be excluded in the Cal/Val of remotely sensed U10.

We examined whether the ambient illuminance during extended wakefulness modulates the homeostatic increase in human deep sleep [i.e. slow wave sleep (SWS) and electroencephalographic (EEG) slow-wave activity (SWA)] in healthy young and older volunteers. Thirty-eight young and older participants underwent 40 hours of extended wakefulness [i.e. sleep deprivation (SD)] once under dim light (DL: 8 lux, 2800K), and once under either white light (WL: 250 lux, 2800K) or blue-enriched white light (BL: 250 lux, 9000K) exposure. Subjective sleepiness was assessed hourly and polysomnography was quantified during the baseline night prior to the 40-h SD and during the subsequent recovery night. Both the young and older participants responded with a higher homeostatic sleep response to 40-h SD after WL and BL than after DL. This was indexed by a significantly faster intra-night accumulation of SWS and a significantly higher response in relative EEG SWA during the recovery night after WL and BL than after DL for both age groups. No significant differences were observed between the WL and BL condition for these two particular SWS and SWA measures. Subjective sleepiness ratings during the 40-h SD were significantly reduced under both WL and BL compared to DL, but were not significantly associated with markers of sleep homeostasis in both age groups. Our data indicate that not only the duration of prior wakefulness, but also the experienced illuminance during wakefulness affects homeostatic sleep regulation in humans. Thus, working extended hours under low illuminance may negatively impact subsequent sleep intensity in humans.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

This paper uncovers that quantum uncertain principle makes the single particle with global property have no certain path, and then wave of quantum particle can simultaneously do pass the double slits. The two subwaves after passing Young’s double slits are entanglement, they may form interference of subwaves. Consequently, we find a kind of quantum probabilistic entanglements with Wheeler's delayed choice. Quantum particles such as photons, electrons, neutrons, protons etc mean that wave of the quantum particle can simultaneously do pass through Young's double slits, rather than individual quantum particle may pass through Young's double slits at the same time. When considering wave property, we cannot consider particle property (Just as in the photoelectric effect, considering the particle nature of the system, people cannot consider wave property, otherwise the photoelectric effect cannot appear). Therefore, this paper discovers that the ability of single photon to hit electrons out in photoelectric effect is complementarily equivalent to the ability of wave of the single photon to simultaneously pass through Young's double slits in wave-particle duality. Objective criteria for distinguishing classical and quantum particles are discovered and objectively give the applicable realm of quantum mechanics for the first time. The crisis of the single particle’s simultaneously passing through Young's double slits, which has been plaguing physicists in the whole world up to now for decades, is solved, in which the studies are classified as classical and quantum particles, the classical particle and quantum particle wave cannot and can pass the Young’s slits, respectively. This paper discovers both the new physics mechanism of passing the double slits of the wave with the amplitude of 4-dimensional momentum representation wave function reflecting particle nature and the principle of self-adaptive emergence of wave-particle duality, and then using the principle, this paper gives both direct explanations to the current experiments and new predictions of new some experiments for wave-particle duality. All the deduced results here are consistent with all relevant physics experiments.

The subject of the research is to Development of laser ablation method for Fabrication of surface acoustic wave sensors on quartz wafer, the target of the GQW – is to design Acoustic wave sensor by using laser ablation method. By using the surface acoustic wave theory to sense by the signal and using this physical phenomenon, We will design the sensor which transduce an input electrical signal into a mechanical wave which unlike an electrical signal, can be easily influenced by physical phenomena. The device then transducers this wave back into an electrical signal on the secondary terminal of the sensor. Changes in amplitude, phase, frequency, or time-delay between the input and output electrical signals can be used to measure the presence of the desired Our work in this part, especially the practical part like temperature, vibration ,etc. we design a combs on the waver of quartz to make like an electrode primary electrode & secondary electrode by putting coats of cuppers & vanadium on the waver and then using the fiber optic laser regime to design this combs to can able transfer the signal by ablation the most important here to use the regime of fiber optic laser then we using this sensor in any electronic circuit How we will select the suitable kind of laser to design, this is the most important part, and what it will be the diameter of that combs of secondary and primary , how much the value of the wave length to select the micro distant combs to avoid any inductance and interference for transferred signal , also take the benefit of using MEMS theory in our project.

During the period January 2014 – October 2018, four strong earthquakes occurred in the Ionian Sea, Greece. A rich aftershock sequence followed each event of them. More analytically, according to the manual solutions of National Observatory of Athens, the first event (K1), occurred on 26 January 2014 in Kefallinia Island with magnitude M_L = 5.8, which was followed by another in the same region (K2) on 3 February 2014 with magnitude M_L = 5.7. The third event occurred on 17 November 2015, M_L = 6.0 in Lefkas Island (L1) and the last on 25 October 2018, M_L = 6.6 in Zande Island (Z1). The first three of these earthquakes caused moderate structural damages mainly in houses and produced particular unrest to the local population. This work presents first the calculation of the source parameters of the strong events as well as for all earthquakes with magnitude M_L > 4.0, using the methodology of the Moment tensor inversion and secondary data from permanent GPS stations were analyzed to confirm the findings from seismological data and to investigate the displacement due to the earthquakes.

In general, a superconductor has zero resistance, although it requires significant refrigeration or high pressures with high manufacturing costs, which prevents it into practical applications. In other words, solving these issues implies main superconducting researches. To solve these problems, this paper describes a new type of superconductivity, which is independent for temperatures and which operates without pressures. The principles of the presented system are as follows:First a voltage source, a current source and a load are connected in series. Then, the voltage of the voltage source is adjusted to balance the voltage of the load. Under this condition, the balance of the two voltages provides a zero voltage between the taps of the current source and the generated current from the voltage source becomes zero because of the internal infinite resistance of the current source. As a result, the electric powers generated by the two sources are zero, and therefore, the load cannot generate Joule heating because of energy conservation. However, the current from the current source (not the voltage source) is not zero; therefore, we can predict that the resistance of the load must be zero. As a theory, we derived a new electric field and transient attractive force, which result in a very short coherence of an electron pair because there is not the Coulomb repulsive force due to the existence of the above transient attractive force. Note that both the forces are derived by the Poisson equation, which implies that they cannot be compatible. Therefore, the pair combination energy from spins becomes extremely strong, which is not destroyed by the normal heat energy. Moreover, every center-of-mass motion of electron pair results in the Bose-Einstein condensation and the macroscopic wave function, which produces the London equation (i.e., the Meissner effect). Moreover, by introducing the equivalent circuit, this paper conducted numerical calculations. As a result, we could derive numerically zero resistance and responses for additional static magnetic fields as a discharged current, which implies the Meissner effect. Note that this paper has prepared Appendix section, which provides a guide to reproduce actual experiments and preliminary experimental results. These results in the Appendix indicate the zero resistances and Meissner effects.

Lamellar eutectic structure of Al_0.7CoCrFeNi high-entropy alloy (HEA) is emerging as a promising candidate for structural applications because of its high strength-ductility combination. The alloy consists of a fine-scale lamellar fcc+B2 microstructure with high flow stresses >1500 MPa under quasi-static conditions. The response to shear loading was not investigated so far. This is the first report on the shear deformation of an eutectic structured HEA and effect of precipitation on shear deformation. The dynamic shear response (DSR) of the eutectic HEA was examined in two microstructural conditions, with and without the presence of L1₂ precipitates. A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local DSR of the alloy. The adiabatic shear bands (ASBs) in two different microstructural conditions were characterized after deformation at dynamic strain rates. The adiabatic shear localization occurs at low strains for the high strength material, and the eutectic microstructure does not delay cracking. The width of ASBs and the extent of plastic deformation around them has been correlated with the rate of straining. Dynamic recrystallization within ASBs and profuse twinning around it was observed. Local mechanical response of individual lamellae before and after shear deformation was examined using nano-indentation.

The investigation of the electromagnetic properties of biological particles in microfluidic platforms may enable wireless monitoring and interaction with functional activity of microorganisms. Of high relevance is the membrane potential as it is one of the most important parameters of living cells. In particular, the complex mechanisms of the cell’s membrane potential are comparable to the dynamics of bacteria membranes, providing a simplified platform for advancing the current techniques and knowledge of general bio-particle dynamics. In this work, we provide a theoretical analysis and experimental results on the microwave detection of bacteria on a microfluidic-based framework for sensing the membrane potential of bacteria. The results enable to further advance the state-of-the-art of electromagnetic bacteria sensing and microfluidic control, and their implication for measuring and interacting with the cell and its membrane potentials, which is of great importance for developing new biotechnological engineered systems and solutions.

The copper deposition on the platinum and palladium nanoelectrode has been studied using cyclic voltammetry. The use of nanoelectrode platinum and palladium are defined in the study of heavy metals. The noble nanoelectrode of metal has a typical silicone processing structure. In comparison to the nanoelectrodes, the geometry of the electrode series is complex and balanced. Nanoelectrodes of platinum are found effective in detecting heavy metal. There was regular analysis of the use of the sensors. The identification constraints down to the ng /L level was accomplished by refined electrode geometry and the stripping procedures. The process was used for the study of water sample determination. Another heavy metal ion attack voltammetric reaction was studied. The SEM picture clearly observed and characterized the nanoparticle electrode by X-ray diffraction and cyclic voltammetry.

This paper presents the development of a new system designed to measure the local temperature field in adiabatic shear band. Transient temperature field are simultaneously recorded by an array of 32 InSb infrared (IR) detectors and a streak camera working in visible-near infrared (VIS-NIR). Observations in IR offer a low temperature detection limit (350°C) but they are highly sensitive to uncertainty in the emissivity. Observations in VIS-NIR allow for measurement only at high temperatures (750°C) but they are less affected by uncertainty on emissivity and present a higher temperature sensitivity. By performing simultaneous measurements, it is possible to obtain data on a large temperature range with an improved accuracy at high temperature. The different sources of errors caused by uncertainty in the emissivity, spatial and temporal resolution of the detectors has been analyzed and an estimation of the total measurement uncertainty of the system is given.

This study reports the first example of major erosion from hurricanes degrading a rocky coastline anywhere around the Gulf of California, although other sources of evidence are well known regarding the effect of inland erosion due to catastrophic rainfall in the Southern Cape Region of the Baja California peninsula and farther north. The uplifted, 12-meter terrace on the eastern shore of Isla del Carmen is the site of an unconsolidated coastal boulder deposit (CBD) consisting of large limestone blocks and boulders eroded from underlying Pliocene strata. The CBD stretches approximately 1.5 km in length, mostly set back 25 m from the lip of the terrace. The largest blocks of upturned limestone near the terrace edge are estimated to weigh between 5.8 and 28 metric tons. Waves impacting the rocky coast that peeled back slabs of horizontally layered limestone at this spot are calculated to have been between 11.5 and 14 m in height. Analysis of sampled boulders from the CBD set back from the terrace edge by 25 m suggest that the average wave height responsible for moving those boulders was on the order of 4.3 m. Additional localities with exposed limestone shores, as well as other more common rock types of igneous origin, have yet to be surveyed for this phenomenon elsewhere around the Gulf of California.

In this work, we investigate the behaviour of a relativistic scalar particle in the background of the Lorentz symmetry violation determined by a tensor (KF)µναβ out of the Standard Model Extension. A linear electric field and a uniform magnetic can be induced by the violation of the Lorentz symmetry breaking effects, and analyze the behaviour of the scalar particle. We see that the analytical solution to the KG-equation can be achieved, and a quantum effect characterized by the dependence of the magnetic field on the quantum numbers is observed

The aim of this study was to analyze whether the respiratory variation in ECG standard lead II R-wave amplitude (ΔRDII) could be used to assess intravascular volume status following inferior vena cava (IVC) clamping. This clamping causes an acute decrease in cardiac output during liver transplantation (LT). We retrospectively compared ΔRDII and related variables before and after IVC clamping in 34 recipients. Receiver operating characteristic (ROC) curve and area under the curve (AUC) analyses were used to derive a cutoff value of ΔRDII for predicting pulse pressure variation (PPV). After IVC clamping, cardiac output significantly decreased while ΔRDII significantly increased (P = 0.002). The cutoff value of ΔRDII for predicting a PPV >13% was 16.9% (AUC: 0.685) with a sensitivity of 57.9% and specificity of 77.6% (95% confidence interval 0.561 – 0.793, P = 0.015). Frequency analysis of ECG also significantly increased in the respiratory frequency band (P = 0.016). Although significant changes in ΔRDII during vena cava clamping were found at norepinephrine doses < 0.1 μg/kg/min (P = 0.014), such changes were not significant at norepinephrine doses > 0.1 μg/kg/minP = 0.093). ΔRDII could be a noninvasive dynamic parameter in LT recipients presenting with hemodynamic fluctuation. Based on our data, we recommended cautious interpretation of ΔRDII may be requisite according to vasopressor administration status.

The present paper deals with the stochastic modeling of bio-colonization for the computation of stochastic hydrodynamic loading on jacket-type offshore structures. It relies on a multidisciplinary study gathering biological and physical research fields that accounts of uncertainties at all the levels. Indeed, bio-colonization of offshore structures is a complex phenomenon with two major but distinct domains (i) marine biology whose processes are modeled with biomathematics methods and (ii) hydrodynamic processes. This paper aims to connect these two domains. It proposes a stochastic model for the marine organism’s growth and then continues with transfers for assessment of drag coefficient and forces probability density functions that accounts for marine growth evolution. A case study relies on the characteristics (growth and shape) of the blue mussel (Mytilus edulis) in northeastern Atlantic.

We study the center of energy (CE) before and after the separation of superposed wave from a moving medium (MM). It is assumed that two out-of-phase mechanical transverse waves propagating from the opposite directions on a medium moving at non-relativistic speeds are superposed and the superposed portion (SP) is separated from the MM at that moment. We consider the CE of the SP before and after the separation from the MM. The location of CE (LCE) of the SP seems to be at the center of it at the moment of superposition. The SP rotates due to the separation from the MM since the velocity of each portion symmetric with respect to the center of the SP is equal in magnitude and opposite in direction. The magnitudes of velocities of the symmetric portions become different as soon as the SP begins to rotate with the separation from the MM. Then the energies of their symmetric portions are not the same, so the LCE of the SP is not at the center of it. As a result, the LCE of it looks different before and after the separation from the MM. We must find a solution to keep the LCE of the SP constant. We propose that two out-of-phase mechanical transverse waves (MTWs) propagating from the opposite directions on a MM originally have hidden difference in relativistic energy and it suddenly appears within the range observable in Newtonian mechanics when the SP starts rotating. This means that the point of view of hidden difference in relativistic energy is necessary to keep the LCE constant.

A simplified nonlinear dispersive system of BBM-type, initially derived by D. Mitsotakis, is employed here in order to model the generation and propagation of surface water waves over variable bottom. The simplification consists in applying the so-called Boussinesq approximation. Using the finite element method and the FreeFem++ software, we solve numerically this system for three different complexities for the bathymetry function: a flat bottom case, a variable bottom in space, and a variable bottom both in space and in time. The last case is illustrated with the Java 2006 tsunami event. This article is designed rather as a tutorial paper even if it contains the description of completely new adaptation techniques.

In the past 100 years, quantum theory has achieved remarkable achievements and formed a relatively mature system, but at the same time there are still some incomplete places. For example: What is the origin of quantum? What is the origin of quantum entanglement? What is the origin of quantum mechanical wave-particle duality? This is still a problem that the existing quantum theory has not solved. Therefore, this paper attempts to seek a classic interpretation of quantum mechanics to make up for the shortcomings of existing quantum theory. In the latest research, this paper finds a classic interpretation of blackbody radiation, which can explain the discontinuity of light energy from the perspective of classical mechanics. Based on this discovery, this paper successfully explains the origin of quantum, quantum entanglement and wave-particle duality, and eliminates the confusion of quantum mechanical probability waves.

This work is located in a growing sector within the field of renewable energies, wave energy converters (WECs). Specifically, it focuses on one of the point absorbers wave (PAWs) of the hybrid platform W2POWER. With the aim of maximising the mechanical power extracted from the waves by these WECs and reduce their mechanical fatigue, the design of five different model predictive controllers (MPCs) with hard and soft constraints has been carried out. As contribution of this paper, two of the MPCs have been designed with the addition of an embedded integrator. In order to validate the MPCs, an exhaustive study on performance and robustness is realized through simulations carried out in which uncertainties in the WEC dynamics are considered. Furthermore, looking for realistic in these simulations, an identification methodology for PAWs is proposed and validated by means of real time series of a scale prototype.

In the present work, a superlattice structure comprising superconducting and insulator layers is studied. Here, if a magnetic field is applied parallel to the layers, the lack of a pinning center leads to a novel transition; in particular, as the applied magnetic field is reduced, the stationary wave surrounding the magnetic flux quantum in the superconducting layer eventually collides with the superconducting–insulating interfaces on both sides because its radius becomes larger than the width of the superconducting layer. At this instant, the stationary wave will collapse, and a transition will occur: the magnetic quanta are collapsed and thus the uniform magnetic field distribution is achieved, which corresponds to the transition from the superconducting state to the normal state over critical current. Considering a one-dimensional model of the structure, a critical current density equation is derived that indicates an increase in the critical current density for increased applied magnetic field. Subsequently, the same calculation was conducted after changing the direction of the magnetic field component, and the combination of these two calculations expresses the anisotropic property of the structure. The phenomenon is also predicted for anisotropic critical current density. This phenomenon is an important discovery that helps manufacture high-temperature superconducting tape as well as large high-temperature superconducting coils.

The entropy models have been recently adopted in many studies to evaluate the distribution of the shear stress in circular channels. However, the uncertainty in their predictions and their reliability remains an open question. We present a novel method to evaluate the uncertainty of four popular entropy models, including Shannon, Shannon-Power Low (PL), Tsallis, and Renyi, in shear stress estimation in circular channels. The Bayesian Monte-Carlo (BMC) uncertainty method is simplified considering a 95% Confidence Bound (CB). We developed a new statistic index called as FREE_opt-based OCB (FOCB) using the statistical indices Forecasting Range of Error Estimation (FREE) and the percentage of observed data in the CB (N_in), which integrates their combined effect. The Shannon and Shannon PL entropies had close values of the FOCB equal to 8.781 and 9.808, respectively, had the highest certainty in the calculation of shear stress values in circular channels followed by traditional uniform flow shear stress and Tsallis models with close values of 14.491 and 14.895, respectively. However, Renyi entropy with much higher values of FOCB equal to 57.726 has less certainty in the estimation of shear stress than other models. Using the presented results in this study, the amount of confidence in entropy methods in the calculation of shear stress to design and implement different types of open channels and their stability is determined.

Dentin bonding is a key in restorative dentistry. Herein, we developed self-etching two-bottle adhesive system containing 10-methacryloyloxidecyl dihydrogen phosphate monomer (MDP) and the physical, mechanical, and biocompatible properties were evaluated. The characteristics of MDP were analyzed using nuclear magnetic resonance (NMR). The water sorption and solubility, the shear-bond strengths to dentin and enamel, and cytotoxicity tests were performed. The newly blended experimental group showed the lowest thickness and water sorption and solubility values. The shear bond strength to enamel and dentin were comparable to control groups (the three other products) all test groups showed 60% of cell viability. In this study, the properties of the newly synthesized adhesive are comparable with the others. The fundamental goal of this study is to get the MDP patent released, as it is intended for domestic production. For this purpose, this dentin adhesive was developed and compared with the commercial product.

The shear failure of surface methane capture borehole (SMCB) is the main cause of shortening life cycle of SMCB but lack of lithological analysis. In order to improve the stability of SMCB and improve efficient drainage period, it is of great significance to investigate the lithology performances for shear failure of SMCB. Based on the direct shear tests and geological method, the results shows that the shear displacement increases as the grain size decreases. Mechanical jump occurs at the lithological boundaries, which is mainly determined by the composition of rock specimens. The cohesion is the mainly possible reason for the step change of shear strength. Lithology with high quartz and low clay may effectively improve shear strength and failure resistance. Boreholes drilled into the weaker siltstone and mudstone sections may potentially experience preferential damage due to the larger shear displacement and shear strength. Protective measures at these sections may improve the stability of the borehole casing. The probing data where it was found that boreholes closure validated the prediction.

The purpose of this paper is to demonstrate the existence of an artificial magnetic monopole and to introduce new electromagnetic equations by altering an electric field and a magnetic field vectors.As a principle device, a cylindrical condenser is prepared, and a superconducting loop is inserted into it. By this conduction, radial electric fields take a role as the centripetal force and both counterclockwise and clockwise motions are induced. As a result, a stationery wave is formed in which the nodes take a part in creating a monopole as follows.First, employing the Lorentz conservations and because node of the stationary wave has no phases, the momentum k and the vector potential A vanish and instead a magnetic potential appears in order to maintain the Lorentz conservation. This magnetic potential has relationship with an electric potential, and thus consequently, a dependent relationship is obtained between an electric field and a magnetic field vectors. Using this conclusive dependent relationship, we can derive new Maxwell equation assembly which are created by altering the electric field and the magnetic field vectors. In this process, we derive a divergent equation of magnetic fields which is not zero, i.e., the existence of a magnetic monopole. Employing these newly derived Maxwell equation, an electromagnetic wave is derived whose speed is the same as one the existing Maxwell equations provide. As a monopole configuration, this paper discusses the energy gap of the vacuum, which is a result of the Dirac equation and describes a monopole as pairs between two Cooper pairs (i.e. four electrons) whose interaction is a photon. As mentioned, because the total momenta and phases are zero, this paper defines the wave function as the Dirac function and demonstrate the condensation, employing the Bloch’s theorem. Moreover, using the macroscopic basic equations, we retrace the creation of the divergent magnetic field in view of macroscopic phenomenon., which provides results in this paper.In Result section in this paper, we succeeded in demonstrating the distribution of the divergent magnetic field of monopole in terms of both microscopic and macroscopic scales. Furthermore, Discussion section describes properties a magnetic monopole should follow.

This study identifies new Alkali Activated Composite Mud Mortar to alternate Cement Mortar used for laying masonry works. This study handles both experimental and numerical analysis of strength and durability for mortar, especially bond strength along mortar and brick joints have studied detail and compared with ANSYS. The bond strength has estimated through the triplet brick prism of shear behavior. The strength and deformation characteristics of masonry constituents obtained from these tests depend on the actual composite conduct of masonry. There is always a good reception for environmentally friendly, low energy, new construction materials, and used in preparing mortar/brick unit combinations all around the world. Also, this study fulfills those requirements. Especially, masonry laid with the mud mortar meets all. Fly Ash, Ground Granulated Blast furnace Slag, and Quarry Dust have utilized the new composites' preparation with 8Molority, 10Molority developed excellent strength. The composite specimens are having compression and bond strength, ranging from 4.84-5.14 and 0.12-0.18N/mm2. The mixed ratio of materials has taken (0.5 parts of Fly Ash, 0.5 parts of Steel Slag, 1.75 parts of Soil, and 0.25 parts of Quarry Dust). The samples tested resistance against acidic, sulfate, and alkalinity indicated PH values less than 7 and 9 simultaneously. Compression strength varied from 10-20% and gained more and fit composite used for mortar in masonry works.

The signal-to-noise ratio (SNR) data is part of the global navigation satellite systems (GNSS) observables. In a marine environment, the oscillation of the SNR data can be used to derive reflector heights. Since the attenuation of the SNR oscillation is related to the roughness of the sea surface, the significant wave height (SWH) of the water surface can be calculated from the analysis of the attenuation. The attenuation depends additionally on the relation between the coherent and the incoherent part of the scattered power. The latter is a function of the correlation length of the surface waves. Because the correlation length changes with respect to the direction of the line of sight relative to the wave direction, the attenuation must show an anisotropic characteristic. In this work, we present a method to derive the wave direction from the anisotropy of the attenuation of the SNR data. The method is investigated based on simulated data as well by the analysis of experimental data from a GNSS station in the North Sea.

Nonionizing millimeter-waves (MMW) are reported to inhibit cell division of lung cancer cells. In this article, we present a mechanism for the effect of inhibited cell division upon 85-105 GHz MMW irradiation. Strains of cell division model organism Saccharomyces cerevisiae cultured under physiological conditions were analyzed for the effects of MMW exposure. Irradiated cells showed a reduced growth rate than that of control (sham) cells. DNA damage repair mutant (rad52) strain cells were also subjected to MMW exposure to identify the involvement of genomic alteration(s) in this process. Irradiated wild type and rad52 mutant strains showed similar colony growth profiles indicating MMW treatment does not alter genomic DNA. Further, MMW interaction with cytological water was explored as a possible mechanism of action. Cells absorbed more power as compared to plain water. MMW irradiation highly absorbed by the cytological water content likely affects proteomic changes, accounting for the observed effects of inhibited cell division. Irradiations using a standard horn antenna were compared to that of a compact waveguide for increased power which led to complete termination of cell division. Our results provide indications of the development of non-invasive nonionizing irradiation procedures to treat tumor metastasis and control microbial infections.

We apply deep convolutional neural networks (CNNs) to estimate wave breaking type from close-range monochrome infrared imagery of the surf zone. Image features are extracted using six popular CNN architectures developed for generic image feature extraction. Logistic regression on these features is then used to classify breaker type. The six CNN-based models are compared without and with augmentation, a process that creates larger training datasets using random image transformations. The simplest model performs optimally, achieving average classification accuracies of 89% and 93%, without and with image augmentation respectively. Without augmentation, average classification accuracies vary substantially with CNN model. With augmentation, sensitivity to model choice is minimized. A class activation analysis reveals the relative importance of image features to a given classification. During its passage, the front face and crest of a spilling breaker are more important than the back face. Whereas for a plunging breaker, the crest and back face of the wave are most important. This suggests that CNN-based models utilize the distinctive `streak' temperature patterns observed on the back face of plunging breakers for classification.

Floating Offshore Wind Turbine (FOWT) is an innovative technology with little industry guidance for its hull design. Various FOWT floaters with different hull shapes claim to support the same turbines. Structural integrity and material expense analyses of different pontoon shapes were conducted, and it was found that some configurations, such as those with every two columns connected by both pontoon and bracing, have advantages over others. However, it is important to note that the choice of pontoon shape should be based on the wave loading conditions the floater will be exposed to. While a T-shaped pontoon provides a cost-effective solution under certain wave loading scenarios, it may not be the best option for all conditions. Specifically, ring pontoon designs with full bracing were found to be necessary for withstanding certain wave loads. Therefore, it is important to consider different Dominant Load Parameters (DLP) and ensure that a FOWT floater can withstand all applicable DLPs. An uneven hexahedral column shape, which combines the best attributes of square and round shapes, is proposed as a better alternative to cylindrical columns. It offers ease of manufacture and reasonably low drag. Bracing is found to be necessary for withstanding the wind turbine’s incurred moment and forces. The conclusion is that platform design should prioritize manufacturing costs and strength over maximizing hydrodynamic performance.

Slope failures pose a substantial threat to mining activity due to their destructive potential and high probability of occurrence on steep slopes close to limit equilibrium conditions, often found both in open pits and in waste and tailing disposal facilities. The development of slope monitoring and modeling programs usually entails the exploitation of in situ and remote sensing data together with the application of numerical modeling, and it plays an important role in the definition of prevention and mitigation measures aimed at minimizing the impact of slope failures in mining areas. Here we present a new methodology combining satellite radar interferometry and 2D finite element modeling for slope stability analysis at a regional scale, applied within slope unit polygons. We studied a former mining area in southeast Spain, and the method proved useful in detecting and characterizing a considerably large number of unstable slopes. Out of 1,959 slope units used for the spatial analysis of the radar interferometry data, 43 were unstable, with varying values of safety factor and landslide size. Out of the 43 active slope units, 21 exhibited line of sight velocities greater than the maximum error obtained through the validation analysis (2.5 cm/year). Eventually, this work discusses the possibility of using the results of the proposed approach to devise a proxy for landslide hazard. The proposed methodology can help to provide non-expert final users with intelligible, clear and easily comparable information to analyze slope instabilities in different settings, not limited to mining areas.

The beating heart is subject to intrinsic mechanical factors, exerted by contraction of the myocardium (stretch and strain) and fluid forces of the enclosed blood (wall shear stress). The earliest contractions of the heart occur already in the 10-somite stage in the tubular as yet unsegmented heart. With development the looping heart becomes asymmetric providing varying diameters and curvatures resulting in unequal flow profiles. These flow profiles exert various wall shear stresses and as a consequence different expression patterns of shear responsive genes. In this paper we investigate the morphological changes of the heart after changes the blood flow by ligation of the right vitelline vein in a model chicken embryo and analyze the extended expression in the endocardial cushions of the shear responsive gene Tgfbeta receptor III. A major phenomenon is the diminished endocardial-mesenchymal transition resulting in hypoplastic (even absence of) atrioventricular and outflow tract endocardial cushions, that might be lethal in early phases. The surviving embryos exhibit several cardiac malformations including ventricular septal defects and malformed semilunar valves related to a malposition of the aortopulmonary septum and the enclosed neural crest cells. We discuss the results in the light of the interactions between several shear stress responsive signaling pathways including Vegf, Notch, Pdgf, Klf2, eNos, Endothelin and Tgfβ/Bmp/Smad.

The interlaminar strength of mechanically interlocked polymer-metal-interfaces is strongly dependent on the surface structure of the metal component. Therefore, this contribution assesses the suitability of the fractal dimension for quantification of the surface structure as well as interlaminar strength prediction of aluminum/polyamide 6 polymer-metal-hybrids. Seven different surface structures, manufactured by blasting, combined blasting and etching, thermal spraying and laser ablation, are investigated. The experiments are carried out on a novel butt-bonded hollow cylinder testing method that allows shear and tensile strength determination with one specific specimen geometry. The fractal dimension of the metal surfaces is derived from cross-sectional images. For comparison, the surface roughness slope is determined and related to the interlaminar strength. Finally, a fracture analysis is conducted. For the investigated material combination, the experimental results indicate that the fractal dimension is an appropriate measure for predicting the interlaminar strength

Recently, most countries suffering from global warming due to the waste gases coming out of the combustion engines used to generate electric power by traditional methods. Therefore, many countries are currently trying to find alternative solutions to this problem by using renewable energies such as solar energy, wind energy, and energy generated from the waves of the ocean and sea to overcome pollution problems. The waves of the seas and oceans have enormous and largely untapped energy, so this work presents an efficient way to use the energy of sea waves to generate electricity. And also, trying to be a way to produce electricity from wave energy in the future. The best suitable places along the shores of Jizan city were inspected to install the buoy system to revenue advantage of the wave supreme height to achieve the height amount of electrical energy. A mathematical model was made to analyze the wave energy and convert it into energy extracted by mechanical force. The mathematical analyzes used the data collected from satellite maps of the numerous severe waves in the Red sea of the Jazan area, and the data published in previous research along that area. It was found that the beach of the Al Shuqaiq area is the greatest for installing the buoy and obtaining the highest electrical energy due to the presence of the highest wave intensity, followed by the beach of the Baysh and Al Morgan area. Also, one of the objectives of this research is to study the design of a device powered by a buoy to use the waves of the Red Sea to generate electric power. The influence of the buoy system design parameters such as the buoy diameter, length of the cylinder, and the length of the connecting rod on the electrical energy generation from wave energy was investigated. The current device is designed with a gearbox to produce continuous power with a single electric generator. A floating mooring device uses the rise and fall of bulges to convert sea wave energy into electrical energy. The device consists of a float, arm, two wheels of different diameters, a gear set, and an electric generator. The effect of the design of several factors on the performance of the device for converting the sea waves energy into electrical energy, including the length of the buoy arm, the wave height by changing the cam diameter, and the conversion ratios between the gear set, to optimize the output power of the wave energy.

Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in different fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behaviour stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behaviour is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the effect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four different simulations using the Mooney-Rivlin, Yeoh, Gent, and Polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviours and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.

Wave overtopping, i.e., excess of water over the crest of a coastal protection infrastructure due to wave run-up, of a smooth slope can be reduced by introducing slope roughness. A stepped revetment ideally constitutes a slope with uniform roughness. Apart from reducing overtopping, a stepped revetment provides safer access to a beach compared to conventional rubble. In recent years, research studies on stepped revetments have provided valuable findings regarding the performance and design optimization of stepped revetments as a typical mean of coastal protection. A stepped revetment can reduce overtopping volumes of breaking waves up to compared to a smooth slope. The effectiveness of the overtopping reduction decreases with increasing Iribarren number. However, up to date a unique approach applicable for a wide range of boundary conditions is still missing. The present paper critically reviews previous findings, gathers and analyzes data from previous studies and proposes a new formula for robust prediction of overtopping of stepped revetments. By means of this approach a critical assessment based on beforehand disclosed parameter ranges between a smooth slope on the one hand and a plain vertical wall on the other are contrasted. By analysis of a new data set compounded from different original studies a novel empirical formulation is derived to predict the roughness reduction coefficient of a stepped revetment for breaking and non-breaking waves. This coefficient is developed and adjusted for a direct incorporation into the present design guidelines. Underlying uncertainties are clearly addressed and quantified. Scale effects are highlighted.

InGaN/GaN samples grown on c-plane sapphire substrate with different In concentrations by metal organic chemical vapor deposition are demonstrated. The subsequent capping GaN layer growth opens a possibility for dislocation reduction due to the lateral strain relaxation in growth geometry. We present the further growth optimization and innovative characterization of InGaN layers overgrown on different structures with varying In concentrations. The photoelectrical and optical properties of the InGaN layers with or without capping GaN layer were investigated by time-resolved picosecond transient grating and temperature dependence photoluminescence. We note a 10-fold increase in carrier lifetime in the InGaN layers when the sample structure changes from PIN to single InGaN layer.

Pandemics caused by viruses have threatened lives of thousands of people. Viral infection is a complex and diverse process, and substantial studies have been complemented in understanding the biochemical and molecular interactions between viruses and hosts. However, the physical microenvironment where infections implement is often less carefully considered, and the role of mechanobiology in viral infection remains elusive. Mechanobiology focuses on sensation, transduction and response to intracellular and extracellular physical factors by tissues, cells and extracellular matrix. The intracellular cytoskeleton and mechanosensors have been proved to be extensively involved in virus life cycle. Furthermore, innovative methods in vivo and in vitro are being utilized to elucidate how extracellular factors including stiffness, forces and topography in regulating viral infection. Our current review covers how physical factors from different sources coordinate virus infection. We further discuss how this knowledge can be harnessed in future research on cross-fields of mechanobiology and virology.

The present article addresses the long-standing problem of the polymer brush bilayers under stationary shear flow at non-linear response regime where the system gets a non-Newtonian fluid. The main idea behind this research would be the fact that the immense lubricity of the polymer brush bilayers originates from a global restructuring that takes place at large shear rates. It is shown here that physical quantities like, stress tensor, viscosity tensor, the friction coefficient and the chain extensions could become dependent on the shear rate at non-Newtonian regime. Apparently, the sub-linear scaling of the physical quantities at large shear rates is solely due to the fact that the chains stretch in the shear direction.

Self-organized criticality (SOC) is a celebrated paradigm from the 90’s for understanding dynamical systems naturally driven to its critical point, where the power-law dynamics taking place make predictions practically impossible, such as in stock prices, earthquakes, pandemics and many other problems in science related to phase transitions. Shortly thereafter, it was realized that traffic flow might be in the SOC category, implying that conventional traffic management strategies seeking to maximize the local flows can become detrimental. This paper shows that the Kinematic Wave model with triangular fundamental diagram, and many other related traffic models, indeed exhibit SOC, thanks in part to the fractal nature of traffic exposed here on the one hand, and our need to get to our destinations as soon as possible, on the other hand. Important implications for congestion management of traffic near the critical region are discussed, such as: (i) Jam sizes obey a power-law distribution with exponent 1/2, implying that both its mean and variance become ill-defined and therefore impossible to estimate. (ii) Traffic in the critical region is chaotic in the sense that predictions becomes extremely sensitive to initial conditions. (iii) However, aggregate measures of performance such as delays and average speeds are not heavy tailed, and can be characterized exactly by different scalings of the Airy distribution, (iv) Traffic state time-space “heat maps” are self-affine fractals where the basic unit is a triangle, in the shape of the fundamental diagram, containing 3 traffic states: voids, capacity and jams. This fractal nature of traffic flow calls for analysis methods currently not used in our field.

Flow field based methods are becoming increasingly popular for the analysis of interfacial shear rheology data. Such methods take properly into account the subphase drag by solving the Navier-Stokes equations for the bulk phases flows, together with the Boussinesq-Scriven boundary condition at the fluid-fluid interface, and the probe equation of motion. Such methods have been successfully implemented at the double wall-ring (DWR), the magnetic rod (MR), and the bicone interfacial shear rheometers. However, a study of the errors introduced directly by the numerical processing is still lacking. Here we report on a study of the errors introduced exclusively by the numerical procedure corresponding to the bicone geometry at an air-water interface. In our study we directly input a preset the value of the complex interfacial viscosity and we numerically obtain the corresponding flow field and the complex amplitude ratio for the probe motion. Then we use the standard iterative procedure to obtain the calculated complex viscosity value. A detailed comparison of the set and calculated complex viscosity values is made upon changing different parameters such as real and imaginary parts of the complex interfacial viscosity and frequency. The observed discrepancies yield a detailed landscape of the numerically introduced errors.

The paper presents a modeling framework to analyze the effect of episodic rainfall supply on groundwater dynamics in the Ionian coastal plain multilayered aquifer. The focus is essentially on the short-term behavior of the shallowest layer, with a specific analysis on episodic rainfall events. In the studied aquifer, groundwater level responds sensitively to rainfall events, highlighting the presence of preferential recharge zones. The hydraulic head peak is a function of groundwater level antecedent to the rainfall event. A kinematic dispersion wave model was used to model infiltration processes via preferential pathways. A one-dimensional and non-linear particle based numerical model was developed. Particles with constant water volume travel according to celerity and hydraulic dispersion to simulate the infiltration rate wave through the vadose zone. The flow rate that reaches the water table represents the input function to determine groundwater level fluctuations along groundwater flow direction and according to the lithological features of the surficial levels of the multilayered aquifer, its storage capacity changes passing from unconfined to confined conditions. The model was validated with high time resolution time series of precipitation and groundwater level coming from Terra Montonata meteo-climatic and groundwater level monitoring station. The developed model represents a basis for evaluating and predicting groundwater discharge of the shallowest layers of the Ionian coastal multilayered aquifer under natural conditions including episodic rainfall.

Inertial focusing conditions of fluorescent polystyrene spherical particles are studied at the pointwise level along their pathlines. This is accomplished by an algorithm that calculates a de-gree of spreading function of the particles' trajectories taking streaklines images as raw data. Different confinement ratios of the particles and flow rates are studied and the results are pre-sented in state diagrams showing the focusing degree of the particles in terms of their position within a curve of an asymmetric serpentine and the applied flow rate. In addition, together with numerical simulation results, we present empirical evidence that the preferred trajectories of inertially focused spheres are contained within Dean vortices' centerlines. We speculate about the existence of a new force, never postulated before, to explain this fact.

Periodic travelling waves are observed in various brain activities including visual, motor, language, sleep, and so on. There are several neural field models describing periodic waves assuming nonlocal interaction and, possibly, inhibition, time delay, or some other properties. In this work we study the influence of asymmetric connectivity functions and of time delay on the emergence of periodic waves and on their properties. Nonlinear wave dynamics is studied, including modulated and aperiodic waves. Multiplicity of waves for the same values of parameters is observed. External stimulation in order to restore wave propagation in a damaged tissue is discussed.

In this paper, a high-performance antenna array system model is presented to analyze moving-object-skin-returns and track them in the presence of stationary objects using frequency modulated continuous wave (FMCW). The main features of the paper are bonding the aspects of antenna array and electromagnetic (EM) wave multi-skin-return modeling and simulation (M&S) with the aspects of algorithm and measurement/tracking system architecture. The M&S aspect models both phase and amplitude of the signal waveform from a transmitter to the signal processing in a receiver. In the algorithm aspect, a novel scheme for FMCW signal processing is introduced by combining time- and frequency-domain methods, including a vector moving target indication filter and a vector direct current canceller in time-domain, and a constant false alarm rate detector and a mono-pulse digital beamforming angle tracker in frequency-domain. In addition, unlike previous designs of using M×N fast Fourier transform (FFT) for an M×N array, only four FFTs are used, which tremendously saves time and space in hardware. With the presented model, the detection of the moving-target-skin-return in stationary objects under a noisy environment is feasible. Therefore, to track long range and high-speed objects, the proposed technique is promising. Using a scenario having 1) a target with 17 dBm2 radar cross section (RCS) at about 40 km range with 5.93 Mach speed and 11.6 dB post processing signal to noise ratio, and 2) a strong stationary clutter with 37 dBm2 RCS located at the proximity of the target, it demonstrates that the root-mean-square errors of range, angle and Doppler measurements are about 26 meters, 0.68 degree and 1100 Hz, respectively.

Irrigation is a useful crop enhancement procedure up to the point where free surface water appears. Thereafter, water can begin to flow into waterways, leaching nutrients and giving rise to environmental damage, as well as being a waste of a precious resource. The current work addresses the problem of measuring free water on the surface of agricultural soils by a real-time acoustic remote sensing method. Directional acoustic transmitter and receiver arrays are used to define a ‘footprint’ on the ground from which changes in reflectance are sensed. These arrays are mounted on a moving irrigator. Chirp signals are used to provide along-path resolution and to ensure robustness against unwanted acoustic background noise from farm machinery and the irrigator. Field measurements have been conducted above a well-defined ‘quadrat’ with controlled and measured water content, and also with the instrument mounted on an operational irrigator. A structured light camera mounted above the footprint is used to validate surface water fraction. It is found that the areal fraction of free water on the soil surface can be reliably estimated from changes in the amplitude of the reflected sound waves. The mechanism giving rise to the observed acoustic reflectivity changes is discussed and a model is developed which agrees with normalized intensity observations with a coefficient of determination R2 between 0.65 and 0.83. The rms error between model predictions and observations is comparable to the rms variation of the measurements, indicating that there is insignificant error due to the choice of model.

Management of demand and capacity for airport operation is important. The effect of capacity setting on slot adjustment, maximum adjustment and flight delay has been extensively investigated and discussed in previous slot adjustment models. But its effect on characteristics of flight waves has not been studied deeply. At present, in order to resolve the problem that Linear Integer Programming (LIP) is limited in slot allocation due to its fast dimension growth and large memory consumption, the general practice is to optimize the slot application according to data-splitting technology. However, the relationship among data splitting method, capacity setting and characteristics of slot wave has not been investigated in detail, which limits the application of LIP in slot allocation. Through the detailed analysis and testing, we found that the waveform and amplitude of slot wave can be controlled and designed by appropriate virtual capacity settings, while the number of capacity constraints and the computing time is reduced by adopting appropriate data feeding method. Our research also provides clues for further research on the construction of the flight waves for airlines operating at specific airports in order to establish direct or indirect connectivity, and increase hit rate by using our approaches.

Among the most important variables in the design of falling film microreactors (FFMRs) is the liquid film thickness as well as the gas/liquid interfacial area, which dictate the mass and heat transfer rates. In a previous work conducted in our lab the characteristics of a free-falling Newtonian liquid film have been studied and appropriate correlations have been proposed. In this work the geometrical characteristics of a non-Newtonian shear thinning liquid, flowing in an inclined open microchannel, have been experimentally investigated and design correlations that can predict with reasonable accuracy the features of a FFMR have been proposed. The test section used was an open μ-channel with square cross section (Wo=1200 μm) made of brass which can be set to various inclination angles. The liquid film characteristics were measured by a non-intrusive technique that is based on the features of a μ-PIV system. Relevant CFD simulations revealed that the volume average dynamic viscosity over the flow domain is practically the same as the corresponding asymptotic viscosity value, which can thus be used in proposed the design equations. Finally, a generalized algorithm for the design of FFMRs, containing non-Newtonian shear thinning liquids, is suggested.

The paper argues that universal approaches to infiltration and drainage in permeable media that pivot around capillarity and that led to dual porosity, non-equilibrium, or preferential flow need to be replaced by a dual process approach. One process has to account for relatively fast infiltration and drainage based on Newton's shear flow, while the other one is responsible for storage and relatively slow redistribution of soil water by focusing on capillarity. Already Schumacher (1864) postulated two separate processes. However, Buckingham's (1907) and Richards' (1931) apparent universal capillary-based approach to flow and storage of water in soils dominated. The paper introduces the basics of Newton's shear flow in permeable media. It presents experimental support for the four presumptions of (i) sharp wetting shock fronts; (ii) that move with constant velocities; (iii) atmospheric pressure prevails behind the wetting shock front; (iv) laminar flow. It further discusses the scale tolerance of the approach, its relationship to Darcy's (1856) law, and its extension to solute transport.

Thin-film lithium niobate has gained significant attention in photonics due to its broad optical transparency, high refractive index, nonlinear coefficient, and substantial electro-optic coefficient. It holds great promise for developing electro-optic modulators with low loss, a compact size, and wide bandwidth. This study focuses on a meticulous investigation utilizing microwave photonics to establish a high-performance electro-optic modulator. Specifically, we analyze the optical mode field distribution and traveling wave electrode structure of lithium niobate thin-film materials. The proposed modulator achieves an impressive half-wave voltage-length product of 1.69 V·cm, a negligible metal loss of 0.01 dB/cm, and a substantial 3dB electro-optic bandwidth of 50 GHz. This research successfully realizes low-loss, high-efficiency LNOI electro-optical modulators, providing a strong foundation for large-scale integrated optoelectronic systems.

Is immediate action at a distance, like gravitational attraction, imaginable using the contrary concept of close up, tactile, events? Tactile events, defined with the term ‘tap-tapping’ as a blind man does, described in a two-way spiritual interaction theory, are implemented in physics to understand gravitation from this respect. The quantum mechanical wave function reduction during measurements receives a new approach. Formulated is a new proof for Einstein’s Equivalence Principle, extending it beyond locality, and a sketch of how tactile interaction could explain dark energy and an accelerated expansion of the universe. Dark energy and dark matter are examples starting from which to discuss properties of matter and space and gravitation as immediate tactile action rather than mediated action such as electromagnetism.

In the first part of this talk we review some prerequisites for and essential arguments involved in the construction of the thermal-ground-state estimate for the deconfining phase in the thermodynamics of SU(2) Quantum Yang-Mills theory and how this structure supports its distinct excitations. The second part applies deconfining SU(2) Yang-Mills thermodynamics to the Cosmic Microwave Background in view of (i) a modified temperature-redshift relation with an interesting link to correlation-length criticality in the 3D Ising model, (ii) the implied minimal changes in the dark sector of the cosmological model, and (iii) best-fit parameter values of this model when confronted with the spectra of the angular two-point functions TT, TE, and EE, excluding the low-$l$ physics. The latter, which is treated in an incomplete way because of the omission of radiative effects, is addressed in passing towards future work.

Electrifying off-grid and isolated islands in the Philippines remains one of the challenges that hinders community development. One of the solutions seen to ensure energy security, expand energy access and promote a low carbon future in this isolated islands is the use of renewable energy sources. This study wishes to determine the nearshore wave energy resource during monsoon seasons in Cuyo Island using a 40-year wave hindcast and 9-year on-site wind speed data to develop high resolution wave energy model using SWAN wave model, and assessed its annual energy production through matching with wave energy devices. Results shows that average significant wave height (Hs), peak period (Tp) and wave power density (Pd) during northeast monsoon are Hs = 1.35 m, Tp = 4.79 s and Pd = 4.05 kW/m respectively, while southwest monsoon which is sheltered by the mainland resulted to a lesser outcome, Hs = 0.52 m, Tp = 3.37 s and Pd = 0.34 kW/m. While the simulated model was observed to overestimate the wave energy resource (Bias = 0.398, RMSE = 0.54 and SI = 1.34), it has a strong relationship with the observed values (average r = 0.9). Its annual energy production is highest at Station 5, with AEPWaveBouy = 43.761 MWh, AEP-Pelamis = 216.786 MWh and AEPWave Dragon = 2462.66 MWh. At present, the minimum requirement for a wave energy development to be feasible is 5 kW/m, which in this case, Cuyo Island falls short, but with the continuous evolution of wave energy converters, applications on milder re-sources will soon materialized.

Computational Fluid Dynamics (CFD) simulations, based on Reynolds Averaged Navier Stokes (RANS) models, are a useful tool for a wide range of coastal and offshore applications, providing a high fidelity representation of the underlying hydrodynamic processes. Generating input waves in the CFD simulation is performed by a numerical wavemaker (NWM), with a variety of different NWM methods existing for this task. While NWMs, based on impulse source methods, have been widely applied for wave generation in depth averaged, shallow water models, they have not seen the same level of adoption in the more general RANS based CFD simulations, due to difficulties in relating the required impulse source function to the resulting free surface elevation for non-shallow water cases. This paper presents an implementation of an impulse source wavemaker, which is able to self-calibrate the impulse source function to produce a desired wave series in deep or shallow water at a specific point in time and space. Example applications are presented, for a numerical wave tank (NWT), based on the opensource CFD software OpenFOAM, for wave packets in deep and shallow water, highlighting the correct calibration of phase and amplitude. Also, the suitability for cases requiring very low reflection from NWT boundaries is demonstrated. Possible issues in the use of the method are discussed and guidance for good application is given.

An analysis of the consistency of the Abraham and Minkowski momenta in the determination of the photon trajectory was carried out considering a new principle of conservation of the photon's mechanical energy, in which the photon conserves translational energy in orbital angular momentum when transiting between two media, introducing the relativistic energy wave (REW). The confrontation between REW and the recent theory of space-time waves (ST) was considered, pondering your differences. Throughout this study it was possible to verify that the Abraham momentum appears a relativistic photon ignition device in the transition between two media, acting as the hidden momentum of the Minkowski’s relativistic momentum. The wavy behavior in the matter is relativistic, and the relativistic trajectory appears with delays and advances, with points of synchronization between source-observer. The classical or relativistic trajectories are determined as a function of the angle of incidence and the relative refractive index, by one of two distinct non-additive torques, the classic by Abraham or the relativistic by Minkowski. It was found that the same analysis conducted under the principle of conservation of the mechanical energy of the photon can be treated by an new Doppler, Relativistic Apparent, that can be confused with other Dopplers in the treatment of redshift from distant sources. It was found that the conservation of energy in Orbital Angular Momentum (OAM), in the interaction with matter, explains that the synchronization instants are found in the inversion of the OAM, where the advances and delays of REW occur under negligible variations of the OAM, however, opposites.

How does the human neurophysiological system self-organize to achieve optimal phase relationships among joints and limbs, such as in the composite rhythms of butterfly and front crawl swimming, drumming, or dancing? We conducted a systematic review of literature relating to CNS control of phase among joint/limbs in continuous rhythmic activities. SCOPUS and Web of Science were searched using keywords ‘Phase AND Rhythm AND Coordination’. This yielded 998 matches from which 23 papers were extracted for inclusion based on screening criteria. The empirical evidence arising from in-vivo, fictive, in-vitro, and modelling of neural control in humans, other species, and robots indicates that the control of movement is facilitated and simplified by innervating muscle synergies by way of spinal central pattern generators (CPGs). These typically behave like oscillators enabling stable repetition across cycles of movements. This approach provides a foundation to guide the design of empirical research in human swimming and other limb independent activities. For example, future research could be conducted to explore whether the two-layer CPG model proposed by Saltiel et al [1] to explain locomotion in cats might also explain the complex relationships among the cyclical motions in human swimming.

This study on the production of a modern natural water electrochemical antimony (II) test include the use of platinum platinum electrode electrodes. Antimony (II) was pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = -680 mV. Compared to the platinum electrode, the platinum nanoelectrode exhibited superior performance and, unexpectedly, received a higher electrochemical response. After 25 min of accumulation, time the best-defined anodic peak was obtained with 0.2 mol L^-1 KNO₃ pH 5.0. Using these parameters, the L^-1 Sb ^{2 +} calibration plot was linear over range 1 = 10⁻⁸ to 5x10⁻⁶ mol. The precision was tested by carrying out eight replicate measurements at a concentration of 2.5x10⁻⁵ mol. L^-1; the variance coefficient was 2.9%. The method was applied to analyte determination in water samples from the river. Other metal ion attack on Sb's (II) voltammetric response has been studied. In the SEM image, the nanoparticle electrode was clearly observed and characterized by X-ray diffraction and cyclic voltammetry

This dataset consists of integral sea state parameters of significant wave height (SWH) and mean wave period (zero-upcrossing mean wave period, MWP) data derived from the advanced synthetic aperture radar (ASAR) onboard the ENVISAT satellite over its full life cycle (2002-2012) covering the global ocean. Both parameters are calibrated and validated against buoy data. A cross-validation between the ASAR SWH and radar altimeter (RA) data is also performed to ensure that the SAR-derived wave height data are of the same quality as the RA data. These data are stored in the standard NetCDF format, which are produced for each ASAR wave mode Level1B data provided by the European Space Agency. This is the first time that a full sea state product in terms of both the SWH and MWP has been derived from spaceborne SAR data over the global ocean for a decadal temporal scale.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

An abdominal aortic aneurysm (AAA) is usually asymptomatic until rupture, which is associated with extremely high mortality. Consequently, early detection of AAAs is of paramount importance in reducing mortality; however, most AAAs are detected by medical imaging incidentally. The aim of this study was to investigate the feasibility of machine learning-based pulse wave (PW) analysis for the early detection of AAAs using a database of in silico PWs. PWs in the large systemic arteries were simulated using one-dimensional blood flow modelling. A database of in silico PWs representative of subjects (aged 55, 65 and 75 years) with different AAA sizes was created by varying the AAA-related parameters with major impacts on PWs – identified by parameter sensitivity analysis – in an existing database of in silico PWs representative of subjects without AAA. Then, a machine learning architecture for early detection of AAAs was proposed, which was trained and tested using the new in silico PW database. The parameter sensitivity analysis revealed that the AAA maximum diameter and stiffness of the large systemic arteries were the dominant AAA-related biophysical properties that significantly influence the PW. The simulated PW indexes extracted from the database showed that the PW was not only influenced by the presence of an AAA but was also significantly affected by multiple cardiovascular parameters that compromised the detection of AAAs by using individual PW indexes. Alternatively, the trained machine learning model performed well in classifying normal and AAA conditions using digital photoplethysmogram PWs from the database. These findings suggest that machine learning-based PW analysis is a promising approach for AAA screening using PW signals acquired by wearable devices.

This article is a followup to an earlier review which outlined some of the interesting features of the soliton/wave-action potential (AP) model, and noted the need to test its key aspects; including the need to test if its presumed lipid phase transition is actually happening during AP firings in excitable cells. The intent here is to point out the sort of tests, and evidence from them, that might be needed if the soliton/wave-AP model is to be accepted broadly by biologists. Here, after an overview of the modern electrophysiological-AP model and of the soliton/wave-AP model, there are three areas considered. First, possible compositional influences on membrane properties relative to the soliton/wave-AP model are presented. Including questions with regard to the soliton/wave-AP model’s assumption that changes in surface potentials influence the transmembrane potential. Second, some recent work from the good folks who advocate for the soliton/wave-AP model concerning the occurrence of lipid phase transitions in neurons or in extracts from nervous tissues are examined. Here it is noted that there is a need to consider whether these lipid phase transitions happen within normal physiological conditions or not. Third, and finally, the advocates for the soliton/wave-AP model have adopted a thermodynamic/theory-based philosophical approach in their studies. It is argued that this philosophical approach is a radical departure from the philosophical approach used under the scientific method. The features of this new approach, and implications its use, are examined.

Density distribution function of classical statistical mechanics is generally generalized as a product of a general complex function and its complex Hermitian conjugate function, and the average of classical statistical mechanics is generalized as the average of the quantum mechanics. Furthermore, this paper derives three ones of the five axiom presumptions of quantum mechanics, e.g., deduces Schrȍdinger equation by two general ways, makes the three axiom presumptions into three theorems of quantum mechanics, not only solves the crisis to hard understand, but also gets new theories and new discoveries, e.g., this paper solves the crisis of the origin of the wave-particle duality, derives operators, eigenvalues and eigenstates, deduces commutation relations for coordinate and momentum as well as the time and energy, and discovers quantum mechanics is just a generalization ( mechanics ) theory of the complex square root of ( real density function of ) classical statistical mechanics. Quantum mechanics being just a generalization theory of the complex square root of classical statistical mechanics is both new physics and revolutionary discovery, which are affecting people’s deep philosophical thinking for modern physics development, solve all the crisises of quantum mechanics, quantum information and so on, and make quantum mechanics have scientific solid bases being checked and both no basic axiom presumption and no all the quantum strange incomprehensible properties, because classical statistical mechanics and the complex square root of classical statistical mechanics have the scientific solid bases being checked. In addition, this paper discovers the reason no taking the time derivative of space coordinates in Schrȍdinger equation. Therefore, this paper gives solution to the crisis of the first quantization origin, and mainly deduces quantum physics no all the quantum current strange incomprehensible properties.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

This paper introduces a model-free, "on-the-fly" learning control strategy for arrays of energy converters with adjustable generator damping. The devices are arranged so that they are affected simultaneously by the energy medium. Each device uses a different control strategy, of which at least one has to be the machine learning approach presented in this paper. During operation all energy converters record the absorbed power and control output; the machine learning device gets the data from the converter with the highest power absorption and so learns the best performing control strategy for each state. Consequently, the overall network has a better overall performance than each individual strategy. This concept is evaluated for wave energy converter (WEC) with numerical simulations and experiments with physical scale models in a wave tank. In the first of two numerical simulations, the learnable WEC works in an array with four WECs applying a constant damping factor. In the second simulation, two learnable WECs were learning with each other. It showed that in the first test the WEC was able to absorb as much as the best constant damping WEC, while in the second run it could absorb even slightly more. During the physical model test, the ANN showed its ability to select the better of two possible damping coefficients based on real world input data.

Satellite altimetry is successfully developing during the past three decades for the sea level, ocean dynamics, coastal oceanography, planetary waves, ocean tides, wind and wave, ice cover, Earth’s gravity field, and climatology research. We propose a new essential add-on of satellite altimetry related to the peculiarities of the orbits of the Topex/Poseidon and Jasons’ satellite missions which were not mentioned before in the scientific publications. Derived subsets of “self-crossover” and “inter-crossover” points in sub-polar latitudes are discussed in detail in the context of water exchange, and wind-wave dynamics, and potential challenges to be solved. The relatively short time lags between measurements at these crossovers provide additional information on anomalies of magnitudes and directions of ocean currents, and characteristics of wind-driven waves. Resulting data snapshots with constant space and time intervals can be regarded as time series of virtual buoys, an analog of continuous buoy measurements of the sea level, wind speed, and wave height. Areas of the World Ocean where these specific crossovers occur are described in the context of water exchange, wind wave studies, and potential challenges to be solved. The value of these special crossovers for studies and monitoring of the sub-polar seas is illustrated by a case study.

Renovation, restoration, remodeling, refurbishment, and retrofitting of build-ings often imply modifying the behavior of the structural system. Modification sometimes includes applying forces (i.e., concentrated loads) to beams that before were subjected to distributed loads only. For a reinforced concrete structure, the new condition causes a beam to bear a concentrated load with the crack pattern that was produced by the distributed loads that acted in the past. If the concentrated load is applied at or near the beam’s midspan, the new shear demand reaches the maximum around the midspan. But around the midspan, the cracks are vertical or quasi-vertical, and no inclined bar is present. So, the actual shear capacity around the midspan not only is low, but also can be substantially lower than the new demand. In order to bring the beam capacity up to the demand, fiber-reinforced-polymer composites can be used. This paper presents a design method to increase the concentrated load-carrying capacity of reinforced concrete beams whose load distribution has to be changed from distributed to concentrated, and an analytical model to pre-dict the concentrated load-carrying capacity of a beam in the strengthened state.

With global warming and accelerated degradation of permafrost, the engineering problems caused by the formation of weak zones between the shallow and permafrost layers of soil–rock mixture (S-RM) slopes in permafrost regions have become increasingly prominent. To explore the influence of rock content on the shear strength of the S-RM freezing–thawing interface, the variation in the shear strength for different rock content is studied herein using direct shear tests. In addition, a 3D laser scanner is used for obtaining the topography of the shear failure surface. Combined with the analysis results of the shear band-particle calculation model, the influence of the rock content on the shear strength of the interface is explored. It was found that the impact threshold of the rock content on the interface strength and failure mode is approximately 30%, when the rock content (R) is &gt; 30% and that the shear strength increases rapidly with increasing rock content. When R ≤ 30%, the actual shear plane is similar to waves; when R &gt; 30%, the shear plane appears as gnawing failure. The shear strength of S-RM freezing–thawing interface mainly comes from the bite force and friction between particles. The main reason for the increase in shear strength with increasing rock content is the increase in bite force between particles, which makes the ratio of bite force to friction force approximately 1:1.

This paper is devoted to investigate charged vector particles tunneling via horizons of a pair of accelerating rotating charged NUT black hole under the influence of quantum gravitational effects. For this purpose, we use the modified Proca equation incorporating generalized uncertainty principle. Using the WKB approximation to the field equation, we obtain a modified tunneling rate and the corresponding corrected Hawking temperature for this black hole. Moreover, we analyze the graphical behavior of corrected Hawking temperature T'_H with respect to the event horizon for the given black hole. By considering quantum gravitational effects on Hawking temperatures, we discuss the stability analysis of this black hole. For a pair of black holes, the temperature T'_H increases with the increase in rotation parameters α and w, correction parameter β, black hole acceleration α and arbitrary parameter k and decreases with the increase in electric e and magnetic charges g.

Casein hydrolysate improves arterial stiffness, as estimated by brachial ankle pulse wave velocity (baPWV), in untreated hypertensive subjects. Facial pigmentation is a useful biomarker for arterial stiffness. This trial evaluated whether casein hydrolysate improves facial pigmentation in association with changes in arterial stiffness. A randomized, double-blind, placebo-controlled trial was conducted in 80 non-hypertensive Japanese participants randomly assigned to receive either active tablets containing casein hydrolysate or placebo for 48 weeks. Facial pigmentation and baPWV were measured at baseline and at the end of the intervention. Other biochemical atherosclerosis-related parameters were also measured, including advanced glycation end products (AGEs). Changes in facial pigmentation showed a significant difference between the groups. Change in baPWV was significantly better in the active than in the placebo group. In contrast, no significant association was seen between changes in facial pigmentation and those in baPWV. Among other atherosclerosis-related factors, changes in advanced glycation products (AGEs) were significantly decreased in the active compared to the placebo group. Further, changes in facial pigmentation were positively correlated with those in AGEs. Changes in AGEs were independently associated with changes in facial pigmentation. Casein hydrolysate improves facial pigmentation in non-hypertensive participants. Casein hydrolysate may have beneficial effects on glycation stress.

This paper derives measurement and identical principles, then makes the two principles into measurement and identical theorems of quantum mechanics, plus the three theorems derived earlier, we deduce the axiom system of current quantum mechanics, the general quantum theory no axiom presumptions not only solves the crisis to understand in current quantum mechanics, but also obtains new discoveries, e.g., discovers the velocities of quantum collapse and entanglement are instantaneously infinitely large. We deduce the general Schrȍdinger equation of any n particles from two aspects, and the wave function not only has particle properties of the complex square root state vector of the classical probability density of any n particles, but also has the plane wave properties of any n particles. Thus, the current crisis of the dispute about the origin of wave- particle duality of any n microscopic particles is solved. We display the classical locality and quantum non-locality for any n particle system, show entanglement origins, and discover not only any n-particle wave function system has the original, superposition and across entanglements, but also the entanglements are of interactions preserving conservation or correlation, three kinds of entanglements directly give lots of entanglement sources. This paper discovers, one of two pillars of modern physics, quantum mechanics of any n particle system is a generalization ( mechanics ) theory of the complex square root ( of real density function ) of classical statistical mechanics, any n particle system’s quantum mechanics of being just a generalization theory of the complex square root of classical statistical mechanics is both a revolutionary discovery and key new physics, which are influencing people’s philosophical thinking for modern physics, solve all the crisises in current quantum theories, quantum information and so on, and make quantum theory have scientific solid foundations checked, no basic axiom presumption and no all quantum strange incomprehensible properties, because classical statistical mechanics and its complex square root have scientific solid foundations checked. Thus, all current studies on various entanglements and their uses to quantum computer, quantum information and so on must be further updated and classified by the new entanglements. This and our early papers derive quantum physics, solve all crisises of basses of quantum mechanics, e.g., wave-particle duality & the first quantization origins, quantum nonlocality, entanglement origins & classifications, wave collapse and so on.Key words: quantum mechanics, operator, basic presumptions, wave-particle duality, principle of measurement, identical principle, superposition principle of states, entanglement origin, quantum communication, wave collapse, classical statistical mechanics, classical mechanics

Recently Cold Bitumen Emulsion (CBE) mixture technologies have been developed to lower the pavement construction temperatures to reduce the environmental costs and control the gas emissions. Due to its poor early mechanical strength, active fillers (i.e. cement) have been used to obtain high early stiffness in order to have the potential for timely construction of the next layer. There is, however, a lack of understanding about the impact of active fillers nature on viscoelastic behaviour and fatigue damage resistance of CBE mastics. This study, therefore, aims to identify the influence of active fillers on the rheological properties and the resulted fatigue behaviour of CBE mastic, supported by chemical analysis for the filler-bitumen emulsion. For this aim, bitumen emulsion was mixed separately with seven fillers/blended fillers to prepare the CBE mastics. Various experiments include continuous pH monitoring tests (chemical reactivity of filler-bitumen emulsion), Strain sweep (SS) tests, Temperature-Frequency Sweep (TFS) tests, Time Sweep (TS) tests, and Linear Amplitude Sweep (LAS) tests were conducted on the CBE binder and the prepared mastics. Results show that the rheological performance and the fatigue damage resistance is not only dependent on the filler inclusions, but it significantly relies on filler type and chemistry. Based on that, the raise in complex shear modulus and the decrease in viscous components were associated with a significant enhancement in fatigue performance for specific filler.

Classical mechanics describes the laws of motion in the macroscopic material world, while quantum mechanics describes the laws of motion in the microscopic material world that classical mechanics cannot explain, and achieves a highly accurate mathematical representation of the laws of microscopic physical motion. But even with such a successful theory, there is confusion about the probability wave. Therefore, this paper attempts to improve the physical definition of the conceptual basis of quantum mechanics, thus solving the confusion of quantum mechanical probability waves, and finally surprisingly discovered another feasible interpretation of the principle of cosmic redshift and the invariance of the speed of light.

The need for miniaturized shear force sensors is expanding, particularly for biomedical applications. Examples include measuring interfacial shear stresses between a human and an external device (e.g., footwear or a prosthesis). However, there are considerable challenges in designing a shear sensor for these applications due to the need for a small package, low power requirements, and resistance to interference from motion artifact and electromagnetic fields. This paper presents the design, fabrication, and characterization sensor that measures two-axis shear force by detecting displacement between a color panel and a red, green, and blue light-sensing photodiode. The sensor response to applied displacements and forces was characterized under benchtop testing conditions. We also present the design of a prototype wireless version of the sensor for integration into footwear. The sensor exhibited strong agreement with gold standard measurements for two axis shear displacements (R2>0.99, RMSE≤5.0 µm) and forces (R2>0.99, RMSE≤0.94 N). This performance, along with the sensor’s scalability, miniaturized form, and low power requirements make it well-suited a variety of biomedical applications.

Illicit drug consumption is posing critical concerns in our society causing health issues, crime-related activities, and the disruption of border trade. The smuggling of illicit drugs urges the development of new tools for rapid on-site identification in cargos. Current methods used by law enforcement officers rely on presumptive color tests and portable spectroscopic techniques. However, these methods sometimes exhibit inaccurate results due to commonly used cutting agents, the colorful nature of the sample or because the drugs are smuggled (hidden or mixed) in common goods. Interestingly, electrochemical sensors can deal with these specific problems. Herein, an electrochemical device is presented that uses affordable screen-printed electrodes for the electrochemical profiling of illicit drugs by square-wave voltammetry (SWV). The identification of the illicit compound is based on the oxidation potential of the analyte. Hence, a library of electrochemical profiles is built upon the analysis of illicit drugs and common cutting agents. This library allows the design of a tailor-made script that enables the identification of each drug through a user-friendly interface (laptop or mobile phone). Importantly, the electrochemical test is compared by analyzing 48 confiscated samples with other portable devices based on Raman and FTIR spectroscopy as well as a laboratory standard method (i.e. gas chromatography – mass spectrometry). Overall, the electrochemical results obtained through the analysis of different samples from confiscated cargos at an end-user site, present a promising alternative to current methods, offering low-cost and rapid testing in the field.