AgW materials exhibit excellent properties and are widely used as contact materials in low- and medium-voltage switches. In this study, a pre-sintering and infiltration method was employed to pre-sinter W powder with Cu, Ni, and (Cu+Ni) addition in the low temperature range of 950–1050 °C. The low-temperature sintering behaviours of W skeletons with different additives were investigated. Subsequently, AgW70, AgW75, AgW80, and AgW85 materials were prepared through infiltration at 1050 °C. The microstructure morphology and physical properties of high-W contact materials were investigated using a metallographic microscope and scanning electron microscope. The mechanism of low-temperature sintering-infiltration of high-W contact materials was elucidated. The results indicated that pure W and 1% Cu-added W skeletons experience minimal linear shrinkage within the temperature range of 950–1050 °C. The linear shrinkage curves of W skeletons with different additives coincided under the conditions of 950–1000 °C/90 min. At 1050 °C, after sintering for 150 min, the particle boundaries in the W skeleton were fully spheroidised, with a dihedral angle of 120°. At 1050 °C and after 150 min of infiltration, cross-sectional micrographs of the AgW material revealed the presence of irregular Ni layers, where Ni spatially enveloped/encapsulated Ag. With an increase in the W content, the electrical conductivity and relative density of AgW(70–85) materials decreased, whereas the hardness of the materials increased.

The contact materials in high-voltage vacuum interrupter require properties such as high conductivity, high density, and high hardness to minimize arc heat damage. In this study, copper–molybdenum-chromium alloys contact materials are examined for a high voltage contact material. Ball milling process was carried out after analyzing the raw materials of copper, chromium, and molybdenum powders. A green compact was produced using a high press with the mixed powder. Afterwards, composite was produced by sintering method according to temperature and infiltration method according to Cu content in green compact. The composite of sintering method showed a density of 8.55 g/cm3 (relative density 93%) a hardness of 217 HV, and an electrical conductivity of 40.7 IACS% at 1200 °C. The composite of 10 wt.% Cu produced by the Cu infiltration method showed a density of 8.7 g/cm3 (relative density 94%), Hardness of 274HV and electrical conductivity of 39 IACS% at 1300 °C. The measurements of physical properties showed the new possibility of using the Cu–Cr–Mo alloy as a contact material for high-voltage vacuum interrupters.

The application of solvent method in the preparation of polypropylene powders was investigated, including the influence of various technological conditions, such as the raw material melt index of polypropylene, processing temperature, dosage of the solvent and the packing pressure. The experimental data show that using solvent method can effectively produce polypropylene powder, and the optimal technological conditions are: melt index of polypropylene being about 17.8 g/10min, processing temperature being about 166.0 ℃, dosage of the solvent being about 0.067g/ml and the packing pressure being about 0.7MPa.Under this technological conditions, polypropylene powder with excellent sphericity could be prepared, the apparent density of powder can reach 0.40 g/cm3 and the prepared powder displayed a narrow size distribution with the mean size of about 42.7 µm.

The present study analyzed the effect of temperature, pH, retention time, pretreatment and mixing ratio on the anerobic digestion process. The parameters during the anaerobic co digestion of cow manure and food waste were then optimized using the Taguchi experimental design method. ANOVA is carried out to find the significant parameters which influence the biogas production. Experimental tests were carried out at laboratory scale reactors kept at different temperatures (28 °C, 35 °C, and 50 °C). The specific methanogenic Performance (SMP) during anerobic digestion at higher temperatures was characterized with the analysis of acetate, propionate, butyrate, hydrogen, glucose, and formate. The improvement of biogas production with different pre-treatment i.e., ultrasonic, autoclave, and microwave techniques also analysed. The results showed that reactor that maintained at 35 °C showed the highest biogas production. While the reactor that maintained at lower temperature (28 °C) produced the lower volume of biogas. As the retention time increases, the amount of biogas produced increases. Methanogenic activities of microorganisms reduced at higher temperature conditions (65 °C). Biogas production increased by 28.1%, 20.23%, and 13.27 % when the of substrates treated with ultrasonic, autoclave, and microwave, respectively, compared to the untreated substrate. The optimized condition for the highest biogas production during anaerobic co digestion of food waste and cow manure is temperature of 35 °C, pH of 7 and mixing ratio (CM: FW=1.5:0.5). ANOVA showed that temperature is the most important input parameter affecting biogas production, followed by mixing ratio.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

The log data generated during the operation of a software system contains information about the system, and using logs for anomaly detection can detect system failures in a timely manner. Most of the existing log anomaly detection methods are specific to a particular system, have cold start problems, and are sensitive to updates in log format. In this paper, we propose a log anomaly detection method LogBD based on pre-training model and domain adaptation, which uses the pre-training model BERT to learn the semantic information of logs, and can solve the problems caused by multiple meaning words and log statement updates. An anomaly detection method LogBD based on distance to determine anomalies is constructed based on domain adaptation, using TCN networks to extract common features of different system logs and map them to the same hypersphere space. Finally, experiments are conducted on two publicly available datasets to evaluate the method, and the experimental results show that the method can better solve the log instability problem and has some improvement in the cross-system log anomaly detection effect.

The influence of pore size on the toughness of Fe-Mo-Cu-C sintered and carburized components was investigated. The charpy impact value of the component made from Fe-0.4%Mo diffusion-alloyed steel powder mixed with 2%Cu powder and 0.3% graphite powder significantly increased with a decrease in pore size. The highest impact value of 17 J/cm2 was obtained at the average pore size of 12 µm. This value was 25% higher than that of the sintered and carburized component made from conventional Fe- 4%Ni-1.5%Cu-0.5%Mo alloyed steel powder called 4Ni even though the component was made from a Ni-free alloyed steel powder. The mechanism of the improvement of the impact value by pore size refinement and the influence of microstructural difference between the components made from Fe- 0.4%Mo diffusion-alloyed steel powder and 4Ni on toughness is discussed based on optical microstructural observation and crystal orientation analysis data.

Ongoing investigations have highlighted that MIM of Mg shows high potential for mass production of small lightweight components as well as of degradable implants with complex geometry. However, prior research activities have shown that Mg reacts sensitively to atmosphere impurities like oxygen and specific thermal decomposition products of the used backbone polymers. Polyethylene based polymers reveal a negative influence on sintering of Mg while polypropylene based polymers behave uncritically. This work is highlighting that when hydrogen instead of argon atmosphere is used during sintering, the negative influence caused by carbon residuals at the particle boundaries can be prevented. Mg-0.9Ca elongation increased with a slight decrease in UTS revealing a strengthening effect of the carbon residuals at the particle boundaries. For pure Mg UTS could be increased from 7 MPa up to 80 MPa with elongation of 6% showing the positive effect of hydrogen on the sintering of Mg.

The growth of solid particles during liquid phase sintering was modeled by the Cellular Automata method. The binary phase diagram and Fickian approach for the diffusion process were applied to simulate the chemical composition variation in liquid and solid phases during sintering. The Oswald-Ripening effect was considered during the dissolution of the solid phase in the liquid phase. It is used to define the probability of solid-phase dissolution by the liquid phase and develop the model to simulate the alloy with solid solubility. So, the microstructure could be modeled in the liquid phase sintering process.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

The UN Sustainable Development Goal 7 Report 2022 is about ensuring access to clean and affordable energy, which is key to the development of agriculture, business, communications, education, healthcare, and transportation. The lack of access to energy hinders economic and human development. Nevertheless, the current pace of progress is insufficient to achieve Goal 7 by 2030. Huge disparities in access to modern sustainable energy persist. Rising commodity, energy and shipping prices have increased the cost of producing and transporting solar photovoltaics modules, wind turbines and biofuels worldwide, adding uncertainty to a development trajectory that is already far below Goal 7 ambitions. Achieving energy and climate goals will require continued policy support and a massive mobilization of public and private capital for clean and renewable energy such as methane from biomass. An important factor in improving methane yield from biomass waste is pre-treatment of the biomass prior to anaerobic digestion. Size reduction of lignocellulose biomass is important for changing and increasing digestibility thus increasing methane yield. A Hollander beater was used as the mechanical pre-treatment machine throughout this study. Results indicate that methane yield is directly proportional to feedstock/Inoculum (F/I) ratio as higher F/I ratio led to higher methane yield. It was observed at an F/I ratio of 0.5 that 5 minutes pre-treatment time produced highest methane yield, while the lowest methane yield was observed at an F/I ratio of 0.2 with 1 minute of pre-treatment time. Methane yield decreased by 30% from 140 mL gTS-1 at F/I ratio 0.5 with 5 minutes pre-treatment time to 98 mL gTS-1 at F/I 0.2 with 5 minutes pre-treatment time. The optimum methane yield was attained at high F/I ratio allowing sufficient nutrient essential for complete degradation of biomass. Overall, this research shows the Hollander beater is not efficient in optimizing methane yield for cardboard.

The interest in the Spark Plasma Sintering (SPS) technique has continuously increased over the last few years. This article shows the possibility of the development of a SPS device used for material processing and synthesis both in both scientific and industrial applications. This work presents an example of processing Arc-Meleted (half-Heusler, cobalt triantimonide) and SHS-synthesized semiconductors (bismuth telluride) materials with SPS device. The system functionalities expansion is presented, showing the possible way of increasing the information amount obtained about SPS processes and using the SPS apparatus for conducting synthesis of materials and increasing reproducibility and accuracy of process parameters control.

Hemangioblasts give rise to endothelial progenitor cells (EPCs), which also express the cell surface markers CD133 and C-kit. They may differentiate into the outgrowth endothelial cells (OECs) that control neovascularization in the developing embryo. Reduced levels of EPC in circulation have been linked to human cardiovascular disorders, according to numerous studies. Furthermore, preeclampsia and senescence have been linked to levels of EPCs produced from cord blood. Uncertainties surround how preeclampsia affects the way EPCs function. It is reasonable to speculate that preeclampsia may have an impact on the function of fetal EPCs during the in utero period; however, given the present literature's suggestion that maternal vasculopathies, including preeclampsia, damage fetal circulation. Additionally, the differentiation potential and general activity of EPCs may serve as an indicator of the health of the fetal vascular system since they promote neovascularization and repair during pregnancy. Thus, the purpose of this review is to compare, through assessment of their quantity, differentiation potency, angiogenic activity, and senescence, the angiogenic function of fetal EPCs obtained from cord blood for normal and pregnancy problems. This will shed light on the relationship between the angiogenic function of fetal EPCs and pregnancy complications, which could have an effect on the management of long-term health issues like metabolic and cardiovascular disorders in offspring with abnormal vasculature development.

Hypertensive diseases of pregnancy (HDP) represent a global clinical challenge, affecting 5-10% of women and leading to complications for both maternal well-being and fetal development. At the heart of these complications is endothelial dysfunction, with oxidative stress emerging as a pivotal causative factor. The reduction in nitric oxide (NO) bioavailability is a vital indicator of this dysfunction, culminating in blood pressure dysregulation. In the therapeutic context, although antihypertensive medications are commonly used, they come with inherent concerns related to maternal-fetal safety, and a percentage of women do not respond to these therapies. Therefore, alternative strategies that directly address the pathophysiology of HDP are required. This article focuses on the potential of the nitrate-nitrite-NO pathway, abundantly present in dark leafy greens and beetroot, as an alternative approach to treating HDP. The objective of this review is to discuss the prospective antioxidant role of nitrate. We hope our discussion paves the way for using nitrate to improve endothelial dysfunction and control oxidative stress, offering a potential therapy for managing HDP.

The development in the field of ceramics has been increasing over the past several decades. Among all of the dental ceramics, zirconia ceramics show very good mechanical properties and a significant improvement in mechanical function. However, it is properly established that each step of the fabrication process of zirconia ceramics must be controlled to achieve the expected mechanical properties. These steps include the block constructing, sintering process, machining and surface processing. Recent advances have focused on zirconia ceramics in forming and sintering processes, mechanical properties, combining with various materials, and on surface processing. All these items provide conceptions about the formability and machinability of the zirconia. Until now, very excellent studies have been done to specify the evolution of microstructures, phase and mechanical properties of zirconia ceramics during the sintering process. However, more studies are required in this field. This paper aims to demonstrate general views and various studies in the field of zirconia ceramics. The properties, applications and tests performed and the recent developments in the field of zirconia bioceramics are discussed.

A developing energy-saving approach of cold sintering in a pure aqueous medium was applied to the preparation of α-Al2O3 ceramics and performed on spark plasma sintering equipment. The initial γ-Al(OH)3 and γ-AlOOH powders and the cold-sintered ceramics were studied by X-ray diffraction analysis, infrared spectroscopy, thermal analysis, and scanning electron microscopy to reveal the chemical and structural transformations they experienced during the cold sintering. At 450°C and 70 MPa, initial γ-AlOOH transformed into a fragile α-Al2O3 material. Porous α-Al2O3 ceramics with about 60% porosity was obtained after cold sintering of γ-Al(OH)3 in the same conditions combined with subsequent annealing at 1250°C for 3 h. The role of water molecules in the studied processes was considered as the enhancement of structural mobility in the cold-sintered material due to its reversible hydroxylation similar to earlier investigated supercritical water action on the precursors during α-Al2O3 formation. Further improvement of the cold sintering setup and regimens would open prospects in α-Al2O3 ceramics manufacturing by an ecologically benign route.

Commercially pure (c.p.) iron powders with a deliberate high degree of oxidation were consolidated by medium-frequency electrical resistance sintering (MF-ERS). This is a consolidation technique where pressure, and heat coming from a low-voltage and high-intensity electrical current, are simultaneously applied to a powder mass. In this work, the achieved densification rate is interpreted according to a qualitative microscopic model, based on the compacts global porosity and electrical resistance evolution. The effect of current intensity and sintering time on compacts was studied on the basis of micrographs revealing the porosity distribution inside the sintered compact. The microstructural characteristics of compacts consolidated by the traditional cold-press and furnace-sinter powder metallurgy route are compared with results of MF-ERS consolidation. The goodness of MF-ERS versus the problems of conventional sintering when working with oxidized powders is analyzed. The electrical consolidation allows to obtain higher densifications than the traditional route under non-reducing atmospheres.

In the present study, hypereutectic Al-Si alloy compacts and Al-Si/B4C composites were produced by conventional, microwave and spark plasma sintering techniques. The effects of sintering techniques and B4C particle addition on microstructural properties, density, hardness and electrical conductivity were investigated. The microstructures were examined with an optical microscope. Densities were measured using the Archimedes technique. Electrical resistance measurements were made with the four-point probe measurement technique. Elemental Al grains, master alloy grains and primary Si particles were determined in the microstructures of all samples. The addition of 15 wt% B4C caused the porosity rate to increase in the samples. Samples produced with SPS technique gave ≈80% higher hardness values than samples produced with CS and MWS. Compared to the samples produced with CS and MWS, the samples produced with SPS gave higher electrical conductivity values. Electrical conductivities were decreased as the weight percentage of B4C increased in all samples.

This research investigates the effect of pre-soaking treatment on plant-based aggregate using a wet grout binder to formulate a high-strength lightweight concrete (HSLWC). The surface modification utilising a novel grout soaking technique with various water-to-cement (w/c) ratios indicated a new method of approach for the recent development of lightweight plant-based aggregate (LWPA). In this experiment, the fresh and hardened properties of modified LWPA lightweight concrete were assessed by verifying their workability, densities, compressive and split tensile strengths towards the modulus of elasticity. The results showed that pre-soaking plant-based lightweight aggregate (w/c: 0.6, 0.8, 1.0, and 1.2) slightly increased the density of the samples compared to untreated LWPA. The oven-dry density of treated and untreated LWPA is controlled in the range of HSLWC. The outcomes indicated that the workability of the surface- modified LWPA has significant improvement up to 40% in 6 min for (TDS)/0.6 sample compared to the original LWPA. The mechanical properties of the LWPA concrete with surface modification method exhibit substantial increment of compressive strength, split tensile strength, and modulus of elasticity were recorded at 22%, 26%, and 34%, respectively. Significantly, the findings from this scientific method revealed that the pre-soaking treatment method on LWPA has shown to be a highly recommended technique in improving interfacial bonding while performing as one of the most promising solutions to improve the properties of lightweight concrete.

This study investigates the effect of perceived discrimination on the mental health of Afghan refugees, and secondly, tests the distress moderating effects of pre-migration traumatic experiences and post-resettlement adjustment factors. In a cross-sectional design, 259 Afghans completed surveys assessing perceived discrimination and a number of other factors using scales developed through inductive techniques. Multivariate analyses consisted of a series of hierarchical regressions testing the effect of perceived discrimination on distress, followed by a sequential analysis of moderator variables. Perceived discrimination was significantly associated with higher distress, and this relationship was stronger among those with a strong intra-ethnic identity, high civic engagement, and high pre-resettlement traumatic experiences. Discrimination is a significant source of stress for Afghan refugees, which may exacerbate stresses associated with other post-migration stressors. Future research is needed to tailor interventions that can help mitigate the stress associated with discrimination among this highly vulnerable group.

The research results conducted on binderless tungsten carbide (WC) ceramics obtained by Spark Plasma Sintering (SPS) of WC powders with different average particle sizes (0.095, 0.8, 3 μm) are presented. Nonuniform distribution of crystalline phases and microstructure of the WC ceramics was studied using layer-by-layer XRD analysis and SEM. Surface layers of the WC-based ceramics are characterized by nonuniform distribution of W2C crystalline phase and grain sizes, including the appearance of abnormally large grains. Thickness of the nonuniform layer was at least 50 μm. The effect under study is associated with an intense carbon diffusion from graphite foil. On the one hand, this contributed to a decrease in the intensity of W2C phase particle formation, which is transformed into α-WC phase due to the carbon. On the other hand, it caused abnormal grain growth in the layer where the carbon diffused. The obtained value of the carbon diffusion depth exceeds the values known from the literature (up to 1 μm in the case of volume diffusion even at temperature of 2370℃ and exposure time of ~ 60 h). The use of boron nitride (BN) as a protective coating on graphite mold parts did not prevent the formation of nonuniform layer on the ceramic surface.

This paper investigates the density, phase composition, microstructure and mechanical properties (microhardness, fracture toughness) of binderless WC + SiC ceramics obtained by conventional pressureless sintering (CPS) and Spark Plasma Sintering (SPS). α-WC nanopowders obtained by DC arc plasma chemical synthesis and β-SiC powders have been used as raw materials. The content of SiC particles was 1, 3, 5% wt. Excess graphite (0.3, 0.5% wt.) was added to α-WC nanopowders to decrease the volume fraction of W2C particles that negatively affect the mechanical properties of ceramics. WC + 1% wt. SiC + 0.3% wt. C ceramics are shown to have a homogeneous fine-grained microstructure, high relative density, increased microhardness and Palmquist fracture toughness. The CPS and SPS activation energies of WC + SiC nanopowders at an intensive shrinkage stage are determined using the Young-Cutler model. The effect of carbon and SiC particles on the CPS and SPS activation energies of tungsten carbide nanopowders has been analyzed. The CPS activation energies of WC, WC + C and WC + SiC + C nanopowders are shown to be closer to the carbon diffusion activation energy along α-WC grain boundaries. The SPS activation energies of WC and WC + SiC nanopowders turn out to be lower than the carbon grain boundary diffusion activation energy of α-WC.

This study presents a methodology to fabricate Ti6Al4V cylindrical compacts with a highly porous core and dense shell with the purpose to mimic the bone microstructure. Compacts with different core diameters were obtained by conventionally press and sintering. Large pores were created with the aid of pore formers. Sintering kinetics was determined by dilatometry, whereas characterization was performed by X-ray computed tomography. Also, permeability was evaluated on the 3D microstructure and the mechanical strength was evaluated by compression tests. Results indicated that sintering is constraint by the different densification rates of the porous and dense layers. Nonetheless, defectless compacts were obtained due to neck bonding between Ti6Al4V particles. Large pores were located in the designed core with similar pore size distribution. Permeability increased following a power law as a function of the pore volume fraction. Stiffness of bilayer components was driven by the porous core, meanwhile, the strength resulted from the combination of both layers. Bilayer materials obtained showed a permeability and mechanical properties, as well as admissible strain (σy /E) similar to those of human bones.

This study focuses on enhancing controllable fibrin-based hydrogels for tissue engineering, addressing existing weaknesses. By integrating a novel copolymer, we improve the foundation for cell-based angiogenesis with adaptable structural features. Tissue engineering often faces challenges like waste disposal and nutrient supply beyond the 200 µm diffusion limit. Angiogenesis breaks through this limitation, allowing the construction of larger constructs. Our innovative scaffold combination significantly boosts angiogenesis, resulting in longer branches and more capillary network junctions. The copolymer attached to fibrin fibers enables precise adjustment of hydrogel mechanical-dynamic properties for specific applications. Our material proves effective for angiogenesis, even under suppression factors like suramin. In our study, we prepared fibrin-based hydrogels with and without the copolymer PVP12400-co-GMA10mol%. Using a co-culture system of human umbilical vein endothelial cells (HUVEC) and mesenchymal stem cells (MSC), we analyzed angiogenetic behavior on and within the modified hydrogels. Capillary-like structures were reproducibly formed on different surfaces, demonstrating the general feasibility of three-dimensional endothelial cell networks in fibrin-based hydrogels. This highlights the biomaterial's suitability for in vitro pre-vascularization of biohybrid implants.

This study provides a novel method to prepare metal-ceramic composites from magnetically selected iron ore using microwave heating. By introducing three different microwave susceptors (Activated Carbon, SiC, and a mixture of Activated Carbon and SiC) during the microwave process, effective control of the ratio of metallic and ceramic phases has been achieved easily. The effects of the three susceptors on the microstructure of the metal-ceramics and the related reaction mechanisms were also investigated in detail. The results show that the metal phase (Fe) and ceramic phase (Fe2SiO4, FeAl2O4) can be maintained, but the metal phase to ceramic phase changed significantly. In particular, the microstructures appeared as well-distributed nanosheet structures with diameters of ~400 nm and thicknesses of ~20 nm when SiC was used as the microwave susceptor.

The objective of this work is the study the crystal structure and elemental content of braunite-hematite and braunite-psilomelane oxide manganese ores y means of X-ray diffractometry (XRD), Energy Dispersion X-ray (EDX) analysis, and X-Ray fluorescent (XRF) analysis. It was found that heat treatments at 600, 800, and 1000 °C promote the phase transitions of the manganese ores to the formation of thermostable phases hausmannite and bixbyite without change in the metallic composition. The homogeneity of the structure increases with increasing temperature, which is expressed in the decreasing of the Mn content in the EDX spectra after sintering above 800 °C as well as in a decrease of the phase number to only two phases: bixbyite and quartz. Remarkably, the hausmannite phase is obtained in the fraction of 61% after sintering the braunite-hematite ore sample at 1000 °C for 4 h. Since hausmannite is widely used to produce building materials, electrodes, catalysts, and other materials, these results are promising for developing technologies for obtaining new products based on phases of manganese minerals at high temperatures.

Comparison of the influence of conditioning temperature of microspheres made of medical grade poly(L-lactide) (PLLA) and polylactide with 4wt.% of D-lactide content (PLA), on its thermal and structural properties is presented. The microspheres were fabricated by solid-in-oil-in-water method for application in additive manufacturing. The microspheres were annealed below glass transition temperature (Tg), above Tg but below onset of cold crystallization, and at two temperatures selected from the range of cold crystallization corresponding to crystallization of α’ and α form of poly(L-lactide) respectively, i.e., at 40°C, 70°C, 90°C and 120°C, in order to verify the influence of conditioning temperatures on sinterability of microspheres set as sintering window (SW). Based on differential scanning calorimetry measurements SW of microspheres were evaluated with consideration of existence of cold crystallization and reorganization of crystal polymorph. The results indicate that the conditioning temperature influence on availability and range of SW that depending on the D-lactide presence. We postulate the need for an individual approach for polylactide powders in determining the SW as a temperature range free of any thermal events. Moreover, other core powder characteristic, such as residual solvent content, morphology, particle size distribution, powder flowability and thermal conductivity, as a key property for successful laser sintering, are characterized. The microspheres are close to sphere and the size of microspheres are below 100 µm. Residual solvents content decreases with the increase of annealing temperature. The thermal conductivity is 0.073 W/mK and 0.064 W/mK for PLA and PLLA microspheres, respectively, and it depends on the spherical shape of the microspheres. Furthermore, the WAXD studies prove that an increase in the conditioning temperature causes a slight increase in crystallinity degree for PLLA microspheres and clear increase in crystallization for PLA microspheres.

COVID-19 Pandemic management has become the top priority of Government Institutions globally, which is justifiable seeing the high mortality of the disease. In India, Lockdowns by National, State and Local level administrations have greatly reduced the spread of the SARS COV-2 Virus. Some areas with a greater proportion of COVID-19 patients have been declared hotspots with increased restrictions on public activities through law enforcement. But quite often delay in identification of these hotspots leads to community transmission of the Virus thus aggravating the problem. A method to identify the areas which are at risk of becoming the next hotspot for the disease is the need of the hour[1]. In this Research document we will find the probable risk factors and make an appropriate scale to measure the vulnerability of an area, identified by its Postal code. To help with this a Pan India survey by the title of “Survey on General Indian population on the level of preparedness for COVID-19 pandemic” was launched and received around 1250 submissions, with the acquired data we will evaluate the risk factors and make appropriate scale to identify ‘pre-hotspots’.

We aimed to assess the caffeine intake before and during pregnancy, compliance with caffeine recommendations during pregnancy (200 mg/day) and factors associated with higher intakes before and in first trimester of pregnancy. Caffeine consumption was collected in a Spanish cohort of pregnant women through a validated food questionnaire, before and in each trimester of gestation (T1, T2 and T3). 463 pregnant women were recruited and follow-up through pregnancy. Compliance with caffeine intake recommendations during pregnancy and quintiles of mg/day of caffeine before and in T1 of pregnancy were calculated. A multivariate logistic regression, comparing extreme quintiles of consumption (Q1 vs Q5) was used. Mean caffeine intake before pregnancy was 120.05 mg/day (SD 117.85), 42.76 mg/day (SD 63.90) at 12th GW, 42.00 mg/day (SD 59.76) at 24th GW and 39.34 mg/day (SD 50.9) at 32nd GW (p<0.001). 86% of women complied with caffeine recommendations during pregnancy. At pregnancy (T1), being an active smoker was associated with Q5 > 100.1 mg/day, aOR = 22.69; 95% CI 4.67- 110.26. igh diet quality, aOR = 0.30; 95% CI, 0.13- 0.68, and moderate physical activity level, aOR= 0.44; 95% CI, 0.19-1.00, were inversely associated with Q5 > 100.1 mg/day. Pregnant women are mostly adhering to current caffeine intake guidelines. Higher caffeine intake at pregnancy is associated with other unhealthy habits during pregnancy.

Semenov-Tian-Shansky has introduced the modified classical Yang-Baxter equation, which is called the modified $r$-matrix. Relevant studies have been extensive in recent times. This paper is devoted to study cohomology theory of modified Rota-Baxter pre-Lie algebras and its applications. First we introduce the concept and representations of modified Rota-Baxter pre-Lie algebras. We then develop the cohomology of modified Rota-Baxter pre-Lie algebras with coefficients in a suitable representation. As applications, we consider the infinitesimal deformations, abelian extensions and skeletal modified Rota-Baxter pre-Lie 2-algebra in terms of lower degree cohomology groups.

Present research focus on the effect of different processing routes on physical and mechanical properties of nano Ti(CN) based cermet’s with metallic binders. Tungsten carbide (WC) is added as secondary carbide and Ni-Co are added as metallic binders in nano Ti(CN) based cermet processed via Conventional and Spark Plasma Sintering (SPS). Systematic comparison of composition and sintering conditions for different cermet’s’ systems is done to design the novel composition and sintering conditions. Nano TiCN powder was prepared by 30hr of ball milling. Highest density of >98.5% percent was achieved for SPS processed cermet’s sintered at 1200°C and 1250°C for 3 min. at 60 MPa pressure in comparison to conventionally sintered cermet’s at 1400°C for 1hr with two stage compaction process, uniaxially at 150 MPa and isostatically at 300 MPa pressure respectively. Comparison of XRD analysis of milled powders of different time intervals was done to understand the characteristics of the as received and milled powders. Peak broadening was observed after 5 hr. of ball milling, and it increased till 30hr. Also, peak broadening and refined carbide size was observed in XRD and SEM micrograph of SPS processed cermet. TEM analysis of milled powder showed internal structure having regular periodic arrangement of planes. SEM (BSE) images of all cermets primarily showed three major microstructural phases of core-rim-binder with black, grey and white contrast respectively. In the present sintering conditions high hardness of ~16 GPa and fracture toughness of ~9 MPa m1/2 was obtained for SPS processed cermets sintered at higher temperature.

Present study focuses on the synthesis and characterisation of a lightweight ceramic material with electromagnetic interference (EMI) shielding properties, achieved using mullite containing micrometer-sized hollow spheres (cenospheres) and CoFe2O4 nanoparticles. The research explores compositions with varying CoFe2O4 content, ranging from 0 up to 20 wt.%. Сonventional sintering in an air atmosphere is carried out at a temperature between 1100-1300 °C. The addition of ferrite nanoparticles was found to enhance the sintering process of cenospheres, resulting in improved material density and mechanical properties. Furthermore, the study reveals a direct correlation between the concentration of ferrite nanoparticles and the electromagnetic properties of the. By increasing the concentration of ferrite nanoparticles, the electromagnetic shielding effect of the material (saturation magnetization (Ms) and remanent magnetization (Mr)) was observed to strengthen. These findings provide valuable insights into the design and development of lightweight ceramic materials with enhanced electromagnetic shielding capabilities. The synthesized ceramic material holds promise for various applications that require effective electromagnetic shielding, such as in electronics, telecommunications, and aerospace industries.

In order to achieve the target, several activities are being undertaken, including the development of multipurpose reservoir planning for the water supply and sanitation infrastructure, irrigation, and hydropower development for the H project. To undertake this work, the main data given was rainfall data, flow data, catchment area, base population for water supply, and so on. This report presents a specifically preliminary study and design of water supply, irrigation, and hydropower development for the project, which is carried out in accordance with the scope of work given by our professor. The preliminary study and design are therefore to investigate scenarios and alternatives and prepare a document of water supply, irrigation, and hydropower infrastructures for the provision of the assignment. This report, as required in the assignment, contains project background, water sources assessment, selection of suitable hydropower potential, and irrigation sizing, design criteria, descriptions of the proposed scheme, preliminary design of water supply components. The objective of the project is to recommend and design a cost-effective water supply system, irrigation, and hydropower development to supply reliable, sufficient, and safe water from a defined water source to the H project. The specific objectives of the investigation works are: • To assess potential water source alternatives for water supply • Selecting appropriate size for the reservoir which could satisfy all water demand • Assess and select suitable irrigation development and hydropower potential. • Preliminary study and design of all components of the reservoir and appurtenant structures The scope of the project generally focuses on preliminary study and design of water supply, irrigation and hydropower development components from water sources potential and the water balance output.

Epoxy powders offer a low-cost means of manufacturing thick section composite parts, such as those found in wind and tidal turbines. Currently, their processing cycle includes a lengthy drying stage (≥ 15 h) to remove ambient moisture. This prevents void defect formation and, thereby, a reduction in mechanical properties, however, it constitutes up to 60% of the processing time. Little research has been published on the study of this process or its optimisation. Experimental and simulated analyses are used to investigate the effects of hygroscopicity in epoxy powder composites. In particular, focus is given to the drying process, which is used to prevent void defect formation and, thereby, a reduction in mechanical properties. As such, tests are performed to quantify the void content of dried and undried laminates, and to measure its impact on transverse flexural strength. Dynamic vapour sorption analysis is used to study the sorption behaviour of the epoxy powder. Sorption data is fitted to a modified linear driving force model, and then implemented in existing process simulations tools. The drying of a thick epoxy powder composite section is simulated to investigate the influence of powder sintering on the duration required for drying. It is shown that the epoxy powder is slightly hygroscopic (1.36 wt%) and exhibits sorption behaviour that is characteristic of glassy polymers. This results in up to 4.8% voids (by volume) if processed in an undried state, leading to a 43% reduction in transverse flexural strength. Process simulations reveal that a standard drying cycle prematurely sinters the powder; inhibiting moisture release. By maintaining a powder state, simulations show that the drying cycle can be reduced to 5 h.

In view of increasing concerns over non-renewable resource depletion and waste management, this study aimed to apply the Taguchi optimization technique to determine the process conditions for producing bricks by incorporating thin film transition liquid crystal displays (TFT-LCD) waste glass powder with reservoir sediments. An orthogonal array L₁₆(4⁵) was adopted, which consisted of five controllable four-level factors (i.e., cullet content, drying method, preheat time, sintering temperature, and error). Moreover, the analysis of variance method was used to explore the effects of the experimental factors on the density, water absorption, shrinkage ratio, loss of ignition, porosity, and compressive strength of the fired bricks. The microstructures of the fired specimens were investigated by scanning electron microscopy. Then, the large-scale production techniques for fired bricks containing recycled TFT-LCD glass cullet and reservoir sediments was developed in a commercially available tunnel kiln. The test results showed that the structure of fired specimen was loose at a sintering temperature ranged from 900–950 °C. However, the fired specimen showed a significant densification at the sintering temperature of 1050 °C. In addition, Taguchi method is a feasible approach for optimizing process condition of brick using recycled TFT-LCD glass cullet and reservoir sediments and it significantly reduces the number of tests. On the other hand, the characteristics of fired bricks developed in the tunnel kiln were in compliance with Chinese National Standards class Ι building bricks criteria.

Pre-exposure prophylaxis (PrEP) is a highly effective HIV prevention strategy that involves the continuous administration of antiretroviral drugs to HIV-negative individuals wit a substantial risk of contracting an HIV infection. The use of PrEP has shown a reduction in the risk of HIV acquisition through sexual intercourse by up to 99%. Despite its effectiveness, PrEP uptake remains low among populations at high risk of HIV infection. This highlights the need for further research in stratetegies to enhance awareness and uptake of PrEP amongst these specific populations

Metal additive manufacturing (AM) has gained much attentions in recent years due to its advantages including geometric freedom and design complexity, appropriate to a wide range of potential industrial applications. However, conventional metal AM methods have high-cost barriers due to the initial cost of the capital equipment, support and maintenance, etc. This study presents a unique low-cost metal material extrusion (MME) technology. The filaments used have polylactic acid (PLA) as the matrix and metal powders (copper, bronze, stainless steel, high carbon iron, and aluminum) as reinforcements. Using the proposed fabrication technology, test specimens were built by extruding polymer/metal composite filaments, which were then sintered in an open-air furnace to produce solid metallic parts. In this research, the mechanical and thermal properties of the built parts are examined using tensile tests, thermogravimetric-, thermomechanical- and microstructural analysis.

Due to the high specific surface area of titanium aluminide powders, significant and unavoidable surface oxidation takes place during processing. The resulting oxides disrupt the conventional powder metallurgical process route (pressing and sintering) by reducing green strength and sintered properties. Oxide-free particle surfaces offer the potential to significantly increase particle bond strength and enable the processing of difficult-to-press material powders. In this work, the effect of milling titanium aluminide powder in a silane-doped atmosphere on the component properties after pressing and subsequent sintering was investigated. Ball milling was used to break up the oxide layers and create bare metal surfaces on the particles. With the help of silane-doped inert gas, the oxygen partial pressure was greatly reduced during machining. It was investigated whether oxide-free surfaces could be produced and maintained by milling in silane-doped at-mospheres. Furthermore, the resulting material properties after pressing and sintering were an-alyzed using density measurements, hardness tests, EDX-measurements and micrographs. It was concluded, that ball milling in a silane-doped atmosphere produces and maintains oxide-free particle surfaces. These oxide-free surfaces and smaller particle sizes improve the component properties after pressing and sintering.

Silver powder, as the primary component of solar silver paste, significantly influences various aspects of paste performance, including printing, sintering, and conductivity. Silver powders prepared using the liquid-phase reduction method exhibit different microstructures depending on whether the growth process is dominated by aggregation or crystalline growth. This study explores the impact of different silver powder microstructures on packing density and sintering activity. It is observed that polycrystalline aggregated silver powder possesses higher surface energy, lower packing density, and greater sintering activity. Investigation into the influence of different silver powders on the electrical conductivity, adhesion, and structural density of silver paste reveals that polycrystalline aggregated silver powder is more suitable for lower sintering temperature pastes, whereas crystalline growth-type silver powder is better suited for higher sintering temperature pastes, resulting in a denser sintered silver layer. Finally, an analysis of the impact of various silver powders on the aspect ratio and electrical performance of solar cell silver grid lines yields higher aspect ratios (0.40) and photoelectric conversion efficiency (19.26%).

The effects of the additives (silicon carbide and titania) and sintering temperatures on the phases developed, physical and mechanical properties of sintered mullite-carbon ceramic composite produced from kaolin and graphite was investigated. The kaolin and graphite of known mineralogical composition were thoroughly blended with 5 and 3 (vol.) % silicon carbide and titania respectively. From the homogeneous mixture of kaolin, graphite and titania, standard samples were prepared via uniaxial compaction. The test samples produced were subjected to firing (sintering) at 1300˚C, 1400˚C and 1500˚C. The sintered samples were characterized for the developed phases using x‐ray diffractometry analysis, microstructural morphology using ultra‐high resolution field emission scanning electron microscope (UHRFEGSEM). Various physical and mechanical properties were determined. It was observed that the addition of SiC/TiO2 additives to the samples made them to possess very low oxidation indices .This also resulted in improvement in the bulk densities and cold crushing strength of the sample when compared with those without additives. It was concluded that the addition of SiC/TiO2 additives improves on the high temperature oxidation resistance of the mullite-carbon ceramic composite sample.

The article discusses the main technologies for processing titanium-containing raw materials, and the advantages and disadvantages of various technological solutions. The analysis of the literature review showed that the traditional schemes for the production of titanium products are mainly focused on the use of ilmenite concentrates. In connection with the depletion of ilmenite deposits, in the near future there will inevitably be a need to switch to the use of complex ores - titanomagnetites. The obtaining of titanium dioxide from titanomagnetite raw materials with a high content of impurity components requires an individual approach for each specific deposit. It is proposed to consider the possibilities of further improvement of the development of a technological process for low-temperature (1000-1200 oC) processing of titanomagnetite concentrates with the production of pure titanium dioxide.

The current study aimed to evaluate the influence of different sintering temperatures on the properties of copper aluminum oxide (CuAlO₂) pellets synthesized from copper oxide (CuO) and aluminum hydroxide (Al(OH)₃) for application in smart infrastructure systems. The pellets were sintered at 400 K, 1000 K, and 1300 K, in the presence of nitrogen gas flow to reduce the amount of oxygen availability. The CuAlO₂ sintered nanoparticles were chemically analyzed by X-ray diffractometry, and the nanostructure of the materials was studied by scanning electron microscopy. The transmittance of the sintered materials was examined by ultraviolet/visible (UV/Vis) spectrophotometry, and 88% transparency was observed for the pellets sintered at 1300 K. Electrical conductivity was measured at 0.905 mS/cm, indicating a semiconducting behavior.

This longitudinal study examined the development of executive function and calibration accuracy in pre-adolescents. Two hundred sixty two students(127 females) from grades 4 (n = 91), 5 (n = 89) and 6 (n = 82) took measures of executive function and performance calibration in a sport task, three times within a period of 20 months. A latent growth curve modeling analysis showed a significant relation between the rates of change of executive function and calibration. Further, the results showed a dynamic interplay in the development of executive function and calibration. There were significant inter-individual differences in the estimated population means both in executive function and calibration and in the rate of change of executive function, but not in the rate of change for calibration. The age of the participants had a positive effect only on the estimated population mean of executive function.

Nanopowders are continuously under investigation as they open new perspectives in numerous fields. There are two main challenges to stimulate their development: sufficient low-cost high throughput synthesis methods leading to a production with well-defined and reproducible properties, and for ceramics, conservation of their nanostructure after sintering. In this context, this paper presents the synthesis of a pure nanosized powder of ZnO (dv₅₀ ~ 60 nm, easily redispersable) by using a continuous Segmented Flow Tubular Reactor (SFTR), which has previously shown its versatility and its robustness, ensuring a high powder quality and reproducibility over time. A higher scale of production can be achieved based on a “scale-out” concept by replicating the tubular reactors. The sinterability of ZnO nanopowders synthesized by the SFTR was studied, by natural sintering at 900 °C and 1100 °C, and Spark Plasma Sintering (SPS) at 900 °C. The performances of the synthesized nanopowder were compared to a commercial ZnO nanopowder of high quality. The samples obtained from the synthesized nanopowder could not be densified at low temperature by traditional sintering, whereas SPS led to a fully dense material after only 5 minutes at 900 °C, while limiting the grain growth and thus leading to a nanostructured material.

The objectives of this study were to evaluate fixed risk factors associated with PWM and to estimate genetic parameters for PWM. A total of 927 birth records from a mixed population of purebred and crossbred Boer and Spanish goats born between 2016 and 2023 at the International Goat Research Center (IGRC) were used for this study. Four binary traits were studied: D0-3 (death within 3 days after birth), D4-60 (death between 4 and 60 days), D61-90 (death between 61 and 90 days), and D0-90 (death within 90 days). Logistic regression models were used to evaluate the risk factors associated with PWM traits. Bayesian threshold models and Gibbs sampling were used to estimate the genetic parameters. Birth weight, season, litter size, sex, dam age, breed, and heterosis were found to be significantly associated with at least one of the PWM traits. Heritability estimates were 0.263, 0.124, 0.080, and 0.207, for D0-3, D4-60, D61-90, and D0-90, respectively. The genetic correlations between the studied traits ranged from 0.892 (D0-3 and D0-90) to 0.999 (D0-3 and D61-90). These results suggest that PWM in goats is influenced by both non-genetic and genetic factors and can be reduced by management, genetic selection, and crossbreeding approaches.

The present work was aimed at the investigation of effect of High Energy Ball Milling (HEBM) time on the sintering kinetics, structure, and properties of heavy tungsten alloy (HTA) W-7%Ni-3%Fe. The HTA samples were obtained from the nanopowders (20-80 nm) by conventional liquid phase sintering (LPS) in hydrogen and by Spark Plasma Sintering (SPS) in vacuum. The HTA density was shown to depend on the HEBM time non-monotonously that originates from the formation of non-equilibrium solid solutions in the W-Ni-Fe systems during HEBM. The SPS kinetics of the HTA nanopowders was shown to have a two-stage character, the intensity of which depends on the Coble diffusion creep rate and on the intensity of diffusion of the tungsten atoms in the crystal lattice of the -phase. The kinetics of sintering of the initial submicron powders have a single-stage character originating from the intensity of the grain boundary diffusion in the -phase. The dependencies of the hardness and of the yield strength on the grain sizes were found to obey the Hall-Petch relation. The hardness, strength, and dynamic strength in the compression tests of the fine-grained tungsten alloys obtained by SPS and LPS were studied.

Cocoa beans of the CCN-51 clone harvested in the Tumaco region (Nariño, Colombia) were fermented following four different treatments: (1) spontaneously (at room temperature for 120 h) in traditional conditions (Control); (2) traditional processing with a pre-drying (sun-dried for 24 h) treatment (PD); (3) with fermentation (for 120 h) after inoculation of a yeast starter culture (YS); and (4) including both treatments, pre-drying and yeast inoculation (PD+YS). Chemical composition, fatty acids, total polyphenol, methylxanthines (theobromine and caffeine) and lactic acid content of cocoa beans were determined. Chemical and fatty acid composition and theobromine content were not affected by the different fermentation treatment applied. When analysing total polyphenol content, YS and PD+YS treatments significantly increased the content of these compounds at the end of the fermentation process, while PD treatment decreased the caffeine content of cocoa beans. Finally, lactic acid content decreased as a consequence of both inoculation of yeast starter and mainly the pre-drying treatment. In conclusion, solar pre-drying in the open air and the inoculation of a yeast starter treatments could improve the final quality of coca beans.

The laser sintering process and modification of electrophoretic deposition (EPD) YSZ coatings on YSZ air plasma sprayed thermal barrier coatings (TBCs) were investigated. Ni-based superalloy was plasma sprayed using yttria-stabilized zirconia (YSZ) to perform thermal barrier coating with 400 μm thickness. The electrophoretic deposition (EPD) technique was used for depositing nanopowder of YSZ on the surface of YSZ TBCs. In this study, a technology of direct sintering the green EPD layer by laser beam was carried out. The best conditions of deposition YSZ overlay coating using DC current were obtained with applied voltage 40 V, deposition time 5 min, and suspension concentration 10 g/l. Iodine was added to the solutions as the stabilizing agent. To overcome the disadvantages of high sintering temperatures, laser sintering was taken as a new approach. Microstructures for all specimens were studied using Field Emission Scanning Electron Microscopy (FESEM) with EDS analysis. Surface roughness was investigated using AFM analysis and central line average (CLA). The results indicated that the morphology after the direct laser sintering of the EPD layer has a fine and controllable grain size, high hardness, and low roughness. Which is better than the direct laser on plasma-sprayed coatings.

Selective laser sintering (SLS) has drawn attention for the fabrication of three-dimensional oral dosage forms due to the plurality of drug formulations that can be processed. The aim of this work was to employ SLS with a CO2 laser for the manufacturing of carvedilol personalised dos-age forms of various strengths. Carvedilol (CVD) and vinylpyrrolidone-vinyl acetate copolymer (Kollidon VA64) blends of various ratios were sintered to produce CVD tablets of 3.125, 6.25 and 12.5 mg. The tuning of the SLS processing parameter laser intensity, improved printability and impacted the tablet hardness, friability, CVD dissolution rate, and the total amount of drug re-leased. Physicochemical characterization showed the presence of CVD in the amorphous state. X-ray micro-CT analysis demonstrated that the applied CO2 intensity affected the total tablet po-rosity, which was reduced with increased laser intensity. The study demonstrated that SLS is a suitable technology for the development of personalised medicines that meet the required specifications and patient needs.

In order to produce nanostructured Ti0.9Cr0.1C powders, an elemental powder mixture of titanium, chromium, and graphite is milled in this work using a high-energy ball mill for various milling times. Microstructural characteristics such as crystallite size, microstrain, lattice parameter, and dislocation density are determined using X-ray diffraction (XRD). Mechanical alloying successfully produced nanocrystalline (Ti,Cr)C with an average crystallite size of 11 nm. This size of the crystallites is also directly verified using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used to investigate the morphology of the samples. The novelty of this work is advancing the scientific understanding of the effect of milling time on the particle size distribution and crystalline structure, and also understanding the effect of the spark plasma sintering on the different properties of the bulks. Densified cermet samples were produced from the nanocrystalline powders, milled for 5, 10 and 20 hours by SPS process at 1800 degrees for 5 min under a pressure of 80 MPa. Phase changes of the produced cermets were examined according to XRD, SEM/EDX analyses. Significant amounts of Cr and Fe elements were detected, especially in the 20 h milled cermet. The bulk forms of the milled powders for 5 and 20 h had a relative density of 98.43 and 98.51 %, respectively. However, 5 h milled cermet had 93.3 HRA because of the more homogeneous distribution of the (Ti,Cr)C phase, the low iron content and high relative density. According to the 0.0011 mm/year corrosion rate, and 371.68 kΩ*cm2 charge transfer resistance obtained from the potentiodynamic polarization and EIS tests, the 20 h cermet was the specimen with the highest corrosion resistance.

In this study one of the most innovative sintering techniques up to date was evaluated: Electro-Sinter-Forging (ESF). Despite it has been proved to be effective in densifying several different metallic materials and composites, bearing steels such as 100Cr6 have never been processed so far. Pre-alloyed Astaloy CrM powders have been ad-mixed with either graphite or graphene and then processed by ESF to produce a 100Cr6 equivalent composition. Porosity has been evaluated by optical microscopy and compared to that one of 100Cr6 commercial samples. Mechanical properties such as hardness and transverse rupture strength were tested on samples produced by employing different process parameters and then submitted to different treatments (machining, heat treatment). The experimental characterization highlighted that porosity is the factor mostly affecting mechanical resistance of the samples, correlating linearly to the transverse rupture strength. Hardness on the other side does not correlate to the mechanical resistance because process related cracking has a higher effect on the final properties. Promising results were obtained that give room to the sinterability by ESF of materials difficult to sinter by conventional press and sinter techniques.

The development of printing technologies has enabled the realization of electric circuit fabrication on flexible substrate. However, the current technique remains restricted to single-layer patterning. In this paper, we demonstrate a fully solution-processable patterning approach for multi-layer circuits using a combined method of laser sintering and ablation. Selective laser sintering of silver (Ag) nanoparticle-based ink is applied to make conductive patterns on a heat-sensitive substrate and insulating layer. The laser beam path and irradiation fluence are controlled to create circuit patterns for flexible electronics. Microvia drilling using femtosecond laser through the polyvinylphenol-film insulating layer by laser ablation, as well as sequential coating of Ag ink and laser sintering, achieves an interlayer interconnection between multi-layer circuits. The dimension of microvia is determined by a sophisticated adjustment of laser focal position and intensity. Based on these methods, the flexible electronic circuit with chip-size-package light-emitting diodes was successfully fabricated and demonstrated with functional operations.

The Chat Generative Pre-training Transformer (GPT), also known as ChatGPT, is a powerful generative AI model that can simulate human-like dialogues across a variety of domains. However, this popularity has attracted the attention of malicious actors who exploit ChatGPT to launch cyberattacks. This paper examines the tactics that adversaries use to leverage ChatGPT in a variety of cyberattacks. Attackers pose as regular users and manipulate ChatGPT’s vulnerability to malicious interactions, particularly in the context of cyber assault. The paper presents illustrative examples of cyberattacks that are possible with ChatGPT and discusses the realm of ChatGPT-fueled cybersecurity threats. The paper also investigates the extent of user awareness of the relationship between ChatGPT and cyberattacks. A survey of 253 participants was conducted, and their responses were measured on a three-point Likert scale. The results provide a comprehensive understanding of how ChatGPT can be used to improve business processes and identify areas for improvement. Over 80% of the participants agreed that cyber criminals use ChatGPT for malicious purposes. This finding underscores the importance of improving the security of this novel model. Organizations must take steps to protect their computational infrastructure. This analysis also highlights opportunities for streamlining processes, improving service quality, and increasing efficiency. Finally, the paper provides recommendations for using ChatGPT in a secure manner, outlining ways to mitigate potential cyberattacks and strengthen defenses against adversaries.

In this paper, the preparation methods of porous silicon nitride materials with controllable dielectric constant and pore structure were systematically studied. By using microwave sintering technology, porous silicon nitride materials with high closed pore ratio were prepared by adjusting the content of sintering additives and sintering process parameters, and controlling the grain boundary phase and pore structure and size. The effects of sintering conditions on the total porosity, closed porosity, pore structure and dielectric properties of materials were systematically studied.

Introduction Infections caused by multidrug-resistant bacteria (MDR) occur more frequently after pancreaticoduodenectomy (PD) compared to other abdominal surgeries, and infective complications are a leading cause of postoperative morbidity following PD. Pre-operative biliary stent (PBS) placement often leads to biliary contamination, which in turn plays a significant role in postoperative infections. The aim of this study is to evaluate the impact of MDR contamination on short-term postoperative outcomes in patients undergoing PD and to examine the relationship between MDR bacteria, PBS, and bile contamination. Methods This is a retrospective study based on a prospectively maintained database comprising 825 consecutive patients who underwent pancreaticoduodenectomy (PD) between January 2010 and December 2020 at our center. All procedures were conducted with a standardized resection by a dedicated group of surgeons in a specialized pancreatic surgery unit, and the patients were managed according to the same perioperative enhanced recovery protocol. Results MDR bacteria were present in 17.5% of bile cultures, exclusively within the stented group. In our multivariate analysis, the development of a major postoperative complication (MPC) was correlated with the presence of MDR bacteria in the bile (OR 1.66, 95% CI: 1.1-2.52; p = 0.02). MDR bacteria were detected early in the surgical drainage in 144 out of 825 patients (12.1%), with 72.2% having a previous biliary stent placement and 27.8% without stents (p < 0.001). In our multivariate analysis, the development of an MPC was associated with the presence of MDR bacteria in the drainage (OR=1.81, 95% CI: 1.21-2.73, p= 0.0042). Conclusions We demonstrated that MDR contamination worsens the short-term outcomes of patients undergoing PD. Specifically, when MDR bacteria are present in both the bile and drainage, there is a statistically significant increase in the incidence of major postoperative complications (MPC). Our data suggest that the majority of MDR surgical site infections stem from biliary contamination resulting from the placement of a pre-operative biliary stent (PBS).

Objective. To describe patient satisfaction with pre-hospital emergency knowledge and determine if patients and professionals share a common vision on the satisfaction predictors. Methods. A qualitative study conducted in two phases. First, a systematic review following the PRISMA protocol was carried out searching publications between January 2000 and July 2016 in Medline, Scopus, and Cochrane. Second, three focus groups involving professionals (advisers and healthcare providers) and a total of 79 semi-structured interviews involving patients were conducted to obtain information about what dimensions of care were a priority for patients. Results. Thirty-three relevant studies were identified. A majority conducted in Europe using questionnaires. They pointed out a very high level of satisfaction of callers and patients. Delay with the assistance and the ability for resolution of the case are the elements that overlap in fostering satisfaction. The published studies neither reviewed the overall care process nor related the measurement of the real time in responding to an emergency with the satisfaction. The patients and professionals concurred in their assessments about the most relevant elements for patient satisfaction, although safety was not a predictive factor for patients. Response capacity and perceived capacity for resolving the situation were crucial factors for satisfaction. This qualitative approach yielded assistance targets to be improved. Conclusions. Published studies have assessed similar dimensions of satisfaction. Furthermore, despite the fact that few explanations may be given due to the no face to face attention, taking into account the patient’s emotional needs or maintaining contact with the patient until the emergency services arrive are high predictors of the satisfaction.

Inspired by the work of S. D. Odintsov and V. K. Oikonomou, Phys. Rev. D 92, 024016 (2015) [1], the present study reports a reconstruction scheme for f (R) gravity with the scale factor a(t) µ (t _* - t) _c²²describing the pre-bounce ekpyrotic contraction, where t is the big crunch time. The reconstructed f (R) is used to derive expressions for density and pressure contributions and the equation of state parameter resulting from this reconstruction is found to behave like "quintom". It has also been observed that the reconstructed f (R) has satisfied a sufficient condition for a realistic model. In the subsequent phase the reconstructed f (R) is applied to the model of chameleon scalar field and the scalar field f and the potential V(f) are tested for quasi-exponential ex pansion. It has been observed that although the reconstructed f (R) satisfies one of the sufficient conditions for realistic model, the quasi-exponential expansion is not available due to this reconstruction. Finally, the consequences pre-bounce ekpyrotic inflation i n f (R) gravity are compared to the background solution for f (R) matter bounce.

The intricate nature of congenital heart disease requires understanding of complex, patient-specific three-dimensional dynamic anatomy of the heart, from imaging data such as three-dimensional echocardiography for successful outcomes from surgical and interventional procedures. Conventional clinical systems use flat screens and therefore display remains two-dimensional, which undermines the full understanding of the three-dimensional dynamic data. Additionally, control of three-dimensional visualisation with two-dimensional tools is often difficult, so used only by imaging specialists. In this paper we describe a virtual reality system for immersive surgery planning using dynamic three-dimensional echocardiography, which enables fast prototyping for visualisation such as volume rendering, multi-planar reformatting, flow visualisation, and advanced interaction such as three-dimensional cropping, windowing, measurement, haptic feedback, automatic image orientation, and multi-user interactions. The available features were evaluated by imaging and non-imaging clinicians, showing that the virtual reality system can help improve understanding and communication of the three-dimensional echocardiography imaging and potentially benefit congenital heart disease treatment.

Proposed in 1889 by Svante Arrhenius, the Arrhenius equation is an important result in physical chemistry which aims to find the relationship between temperature and reaction rates. It is also an essential equation for analytic chemistry which helps to determine the energy barrier for a given reaction. In this article, we will go through a detailed derivation of the exponential factor in the Arrhenius Equation based on the Boltzmann distribution of particle energy probability. Then, we will attempt to model the pre-exponential factor in accordance with the principles of collision theory for bi-molecular reaction with gaseous reactants. Understanding the basic principles of chemical reaction provides valuable tools to analyze complex reaction mechanisms in the perspective of optimizing existing industrial processes.

The ability to replicate scientific experiments is a cornerstone of the scientific method. Sharing ideas, workflows, data, and protocols facilitates testing the generalizability of results, increases the speed that science progresses, and enhances quality control of published work. Fields of science such as medicine, the social sciences, and the physical sciences have embraced practices designed to increase replicability. Granting agencies, for example, may require data management plans and journals may require data and code availability statements along with the deposition of data and code in publicly available repositories. While many tools commonly used in replicable workflows such as distributed version control systems (e.g. “git”) or scripted programming languages for data cleaning and analysis may have a steep learning curve, their adoption can increase individual efficiency and facilitate collaborations both within entomology and across disciplines. The open science movement is developing within the discipline of entomology, but practitioners of these concepts or those desiring to work more collaboratively across disciplines may be unsure where or how to embrace these initiatives. This article is meant to introduce some of the tools entomologists can incorporate into their workflows to increase the replicability and openness of their work. We describe these tools and others, recommend additional resources for learning more about these tools, and discuss the benefits to both individuals and the scientific community and potential drawbacks associated with implementing a replicable workflow.

This study aimed to evaluate the level of skill in observing teaching competency in pre-service physical education (PE) teachers and provide basic data to cultivate teaching competency. A total of 21 third-year pre-service PE teachers were selected as participants. The study derived descriptive statistics to analyze the participants’ observation skills regarding teaching competency in different class stages using evaluation results of class demonstrations by pre-service teachers. Mann–Whitney U test was conducted to verify the statistical significance of the evaluation between in-service and pre-service teachers. Compared with in-service teachers, pre-service teachers reported high agreement with intuitive teaching behaviors. However, pre-service teachers indicated low agreement with skills that required complex teaching behaviors depending on various situations. Based on theories by Schon (1983), pre-service teachers showed high “knowledge for practice” and low “knowledge in practice.” Thus, pre-service education must balance practical knowledge and theory rather than focus on theory-based education. This study provided directions for pre-service teacher education to enhance the competency of pre-service teachers for leading and analyzing classes.

MicroRNAs (miRNAs) within the exosomes are short non-coding RNAs that are associated with many diseases including cancers and are crucial players in regulating gene expression and regula-tion. Owing to their potential role as emerging biomarkers, efficient isolation, and quantification methods of miRNA from the exosomes in the cell’s supernatant are complicated and challenging. The quantitative PCR method is the gold standard for miRNA identification and estimation. Nucleic acid-based assays are expensive, labour-intensive, and require expertise. In this work, we demon-strated an aptamer-based magnetic separation of the exosomes, and quantification of the miRNA using a fluorescence switching assay. The fluorescence assay relies on the fluorescence of the fluorophore labelled cDNA quenched by carbon nanomaterials coated on magnetic beads (OFF state). When the target miRNA210 is introduced to the system, the cDNA detaches from the quenching surface. As a result, the fluorescence intensity increases (ON state) with increasing miRNA concentration within the dynamic range of 0-100 nM. This method can detect miR210 as low as 5 pM. This method does not exhibit any cross-reactivity with other closely related miRNAs. The method was validated by spiking miRNA with the standard RT-PCR method using SYBR green as a fluorescent probe. This method can be used for the minimally invasive detection of cancer biomarkers in breast cancer patients.

Carbon fiber reinforced polymers (CFRPs) are being used extensively in modern industries that require high strength-to-weight ratio such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymer, this comes on the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent, and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

Currently, one of the biggest issues when developing an ODS alloy is the competition established between the different oxide precursors during the precipitation of oxides which nature depends on their chemical composition. In the presence of various precursors, usually the one with the highest affinity to oxygen leads to the absence of the other oxides. In this work, a new process to equilibrate the local concentration of species and to decrease the competition among them is explained. A unique compound, containing the diverse oxide precursors as one complex oxide, is introduced in a prealloyed 14Cr Steel powder via mechanical alloying. Thus, generating environments enriched in Y, Ti and Zr which, after consolidation, refine the oxides precipitation improving the thermal stability of the alloy. SPS were used as consolidation technique to guarantee shorter sintering times and to maintain the nanostructure obtained. Mechanical properties were tested by tensile tests and Vickers microhardness.

In this paper, the effect of Bi₂O₃ doping on the mechanical properties of PbO ceramic pellets was studied. For this purpose, different ratios of Bi2O3/PbO (i.e., xBi2O3–(1-x)PbO, where x is 0, 1, 3, 5, 7 wt%) were fabricated and sintered at 570, 620, and 670°C. Mechanical properties including density, hardness, flexural strength, and sintering of PbO were studied for the aforementioned compositions. Phase compositions, microstructures, and worn surfaces of the composites were characterized by scanning electron microscopy and X-ray diffraction (XRD). The XRD analysis revealed that a solid solution formed in the composite ceramic. The best suited conditions of temperature and doping of Bi₂O₃ for optimal sintering are 620°C and 3 wt%, respectively. The hardness of the 3 wt% Bi2O3–97 wt% PbO ceramic was 717 MPa, which is about four times higher than the hardness of pure PbO; in addition, the strength of the composites was 43 MPa, which is two times higher than that of pure PbO. The integrity of the composites was verified using the lead–bismuth eutectic alloy flushing experiment. Results of this research paper are important for future studies of oxygen control in the lead–bismuth eutectic alloy of lead-cooled fast reactors.

The aim of this study was to investigate the possibility of a freeform fabrication of porous ceramic parts through selective laser sintering (SLS). SLS was proposed to manufacture ceramic green parts because this additive manufacturing technique can be used to fabricate three-dimensional objects directly without a mold, and the technique has the capability of generating porous ceramics with controlled porosity. However, ceramic printing has yet fully achieved its 3D fabrication capabilities without using polymer binder. Except for the limitation of high melting point, brittleness and low thermal shock resistance from instinct ceramic material properties, the key hurdle lies on very poor absorptivity of oxide ceramics to fiber laser which is widely installed in the commercial SLS equipment. An alternative solution to overcome the poor laser absorptivity via improving material compositions was presented in this study. The positive effect of carbon additive on the absorptivity of silica powder to fiber laser will be discussed. To investigate the capabilities of the SLS process, 3D porous silica structures were successfully prepared and characterized.

Polyamide 11 (PA11) is a plant-based nylon made from castor beans. Powder bed fusion laser sintering (PBF-LS) is an additive manufacturing process used for PA11 which allows the reuse of the unsintered powder. The unsintered powder is mixed with virgin powders at different refresh rates which has been studied extensively for most semi-crystalline polyamides. However, there is lack of information on the effect of using 100% reused PA11 powder and the number of times it is reused on its own during powder bed fusion laser sintering. This paper investigates the effect of reusing PA11 powder in PBF-LS and number of times it is reused on the dimensional accuracy, density, thermal and tensile properties. From 100% virgin powder to 3rd use of the powder, there is a decrease in powder wastage, decrease in crystallinity and tensile strength. These was associated with the polymerisation and cross-linking process of polymer chains, upon exposure to high temperature. This results in a higher molecular weight and hence density. From the 4th use to 10th reuse, the opposite was observed which was associated to an increase in high-viscosity and un-molten particles which resulted in defects in the PBF-LS parts.

Ionic liquids have been recognised as interesting solvents applicable in the efficient lignocellulosic biomass valorisation, especially in the biomass fractionation into individual polymeric components or direct hydrolysis some of biomass fractions. Considering the chemical character of ionic liquids, two different approaches, paved the way for a fractionation of biomass. The first strategy integrated a pre-treatment, hydrolysis and conversion of biomass through the employment of hydrogen-bond acidic 1-ethyl-3-methyimidazolim hydrogen sulfate ionic liquid. The second one relied on the use of a three-step fractionation process with hydrogen-bond basic 1-ethyl-3-methylimidazolium acetate to produce high purity cellulose, hemicellulose and lignin fractions. The proposed approaches were scrutinised for wheat straw and eucalyptus residues. Those different biomasses allowed understanding that enzymatic hydrolysis yields are dependent on the crystallinity of pre-treated biomass. The use of acetate based ionic liquid allowed to change crystalline cellulose I to cellulose II and consequently enhanced glucan to glucose yield to 93.14.1 mol% and 82.91.2 mol% for wheat straw and eucalyptus, respectively. Whereas for hydrogen sulfate ionic liquid, the same enzymatic hydrolysis yields were 61.6  0.2 mol% for wheat straw and only 7.90.3 mol% for eucalyptus residues. These results demonstrate the importance of either ionic liquid character or biomass type on the efficient biomass processing.

A vivid debate is ongoing in the scientific community about statistical malpractice and the related publication bias. No general consensus exists on the consequences and this is reflected in heterogeneous rules defined by scientific journals on the use and reporting of statistical inference. This paper aims at discussing how the debate is perceived by the agricultural economics community and implications for our roles as researchers, contributors to the scientific publication process, and teachers. We start by summarizing the current state of the p-value debate and the replication crisis, and commonly applied statistical practices in our community. This is followed by motivation, design, results and discussion of a survey on statistical knowledge and practice among the researchers in the agricultural economics community in Austria, Germany and Switzerland. We conclude that beyond short-term measures like changing rules of reporting in publications, a cultural change regarding empirical scientific practices is needed that stretches across all our roles in the scientific process. Acceptance of scientific work should largely be based on the theoretical and methodological rigor and where the perceived relevance arises from the questions asked, the methodology employed, and the data used but not from the results generated. Revised and clear journal guidelines, the creation of resources for teaching and research, and public recognition of good practice are suggested measures to move forward.

The purpose of this study was to develop a reflective evaluation tool that can enhance the teaching competency of pre-service physical education teachers. A Delphi survey was conducted to modify the questions based on the evaluation tool for the teaching competency of physical education teachers, and each evaluation standard based on teaching competency was developed. The evaluation tool consisted of 46 questions for class preparation (the creation of the learning environment), the introduction (routine activities, learning goals, and task presentation), development (class strategy, observation and interaction, and the maintenance of the learning environment), and conclusion (routine activities, summary, and closure). It was designed to increase the accuracy of evaluation by developing evaluation criteria for each question. An evaluation tool including quantitative and qualitative methods for use in pre-service physical education teacher education was developed. The significance of this study was the development of an effective evaluation tool that can evaluate the core teaching behaviors in the field of physical education. This evaluation tool should be used as a learning tool that includes planning, operation, evaluation, and seeking improvement measures through reflective activities. If pre-service teacher education institutions apply this evaluation tool in their teacher training programs, it would be a great chance to learn how to develop and sustain teaching abilities and effectiveness.

Global food security for the increasing world population not only requires increased sustainable production of food but a significant reduction in pre- and post-harvest waste. The timing of when a fruit is harvested is critical for reducing waste along the supply chain and increasing fruit quality for consumers. The early in field assessment of fruit ripeness and prediction of the harvest date and yield by non-destructive technologies have the potential to revolutionize farming practices and enable the consumer to eat the tastiest and freshest fruit possible. A variety of non-destructive techniques have been applied to estimate the ripeness or maturity but not all of them are applicable for in situ (field or glasshouse) assessment. This review focuses on the non-destructive methods which are promising, or have already been, applied to the pre-harvest in field measurement including colorimetry, visible imaging, spectroscopy and spectroscopic imaging. Machine learning and regression models used in assessing ripeness are also discussed.

This work presents updated reconstructions of watershed runoff to San Francisco Estuary from tree-ring data to AD 903, coupled with models relating runoff to freshwater flow to the estuary and salinity intrusion. We characterize pre-development freshwater flow and salinity conditions in the estuary over the past millennium and compare this characterization with contemporary conditions to better understand the magnitude and seasonality of changes over this time. This work shows that the instrumented flow record spans the range of runoff patterns over the past millennium (averaged over five, ten, twenty and one hundred years), and thus serves as a reasonable basis for planning-level evaluations of historical hydrologic conditions in the estuary. Over annual timescales we show that, although median freshwater flow to the estuary has not changed significantly, it has been more variable over the past century compared to pre-development flow conditions. We further show that the contemporary period is generally associated with greater spring salinity intrusion and lesser summer-fall salinity intrusion relative to the pre-development period. Thus, salinity intrusion in summer and fall months was a common occurrence under pre-development conditions and has been moderated in the contemporary period due to the operations of upstream reservoirs, which were designed to hold winter and spring runoff for release in summer and fall. This work also confirms a dramatic decadal-scale hydrologic shift in the watershed from very wet to very dry conditions during the late 19th and early 20th centuries; while not unprecedented, these shifts have been seen only a few times in the past millennium. This shift resulted in an increase in salinity intrusion in the first three decades of the 20th century, as documented through early records. Population growth and extensive watershed modification during this period exacerbated this underlying hydrologic shift. Putting this shift in the context of other anthropogenic drivers is important in understanding the historical response of the estuary and in setting salinity targets for estuarine restoration. By characterizing the long-term behavior of San Francisco Estuary, this work supports decision-making in the State of California related to flow and salinity management for restoration of the estuarine ecosystem.

Today, concepts such as Emotional Education and Emotional Intelligence are recognized by many authors and researchers, emphasizing the importance of their development in all people, but especially in schools, specifically in teachers or educators and children. However, we still find many shortcomings within the schools that are needed to continue working. The aim of this study is to investigate the presence of emotional intelligence and empathy in teachers, through a sample of 42 participants. The research was conducted based on two validated and highly reliable assessment tools, called TMMS-24 and TECA. The results of the TMMS-24 indicate that a large percentage of participants have an adequate score of emotional intelligence. The results of the TECA indicate that most of the participants are in the middle, high or extremely high scores in relation to the level of empathy.

BACKGROUND: Pre-marital sex is a sexual interest practiced by people who are yet to get married and has ended up being accepted specifically in western countries. Sex before marriage is sexual behavior engaged in by single people. In the past, having sex before getting married is seen as a moral dilemma that many cultures forbade and that many people regarded to be sin in many religions, although it has gained wider acceptance across the board. OBJECTIVES: This study was carried out to determine the perception, practices, and factors associated with pre-marital sex, courtship, and its influences among Osun State University Undergraduates, Osogbo, Osun State. METHODOLOGY: The study was a descriptive study, and respondents were selected using multi-stage sampling technique. Students of Osun State University, Osogbo main campus form the population of the study and its sample size was calculated using Leslie Kish’s formula. A total of 387 responses were validated from the survey. The instrument for data collection was a self-administered semi-structured questionnaire consisting of four sections. The data obtained were collated, examined for completion, coded, imputed, and analyzed using SPSS v21. RESULTS: The mean age of the respondents was between 19.19±2.17, and the majority were between 18 – 24 years. About 52% of the respondents show a positive perception of premarital sex and courtship. Also, in the practice of courtship majority (88.3%) of the respondents think those that go around together are courting and from the responses obtained and analyzed from the factors leading to pre-marital sex, the findings revealed that peer pressure (90.4%), Internet (86.7%), pornography (83.9%) and drugs (82.9%) are the leading factors which contribute to pre-marital sex among undergraduates. CONCLUSION: The study hereby recommends that Parents should as a matter of responsibility monitor and pays regular visits to their children in the universities and provide them with materials that will make them stay comfortable for them not to fall victim to peer pressure.Pre-marital sex is a practice that should be avoided by undergraduate students, though most students consider courtship as a normal practice, it is still used as a normal factor that leads them to practice pre-marital sex.

Among the plant resources in pre-Columbian Mexico and Central America, the Chia (Salvia hispanica L.) is unique in being the only member of the Lamiaceae cultivated for the mericarps. Recently the crop has gained considerable attention due to its high of content omega-3 polyunsaturated fatty acid, antioxidants, fibre and protein classifying it as a nutraceutical.

Introduction: Exams are a relatively stressful period for all students, especially undergraduate medical students. Exams bring anxiety and stress for the students. Some students experience such high stress that it hinders their academic productivity and reduces their exam performance. The aim of this study is to assess the effects of pre-exam anxiety on the academic performance of medical students. Methods: Two hundred and twenty-five final year medical students completed Westside Test Anxiety (WTA) Scale one month before their exams. Grade Point Average (GPA) of these students was noted when the results were announced. Data was processed and analyzed using SPSS v 22.0Results: The mean anxiety score on WTA scale was 3.46 ± 0.87. All students (100%) who scored ≤ 2.50 GPA were highly-extremely highly anxious. In the 2.51-3.00 GPA group, 46% were highly-extremely highly anxious, 32% were moderately anxious, and 21% had low to normal anxiety. In the 3.01-3.50 GPA group, 30% were highly-extremely highly anxious, 30% were moderately anxious, and 39% had low to normal anxiety. In the 3.51-4.00 GPA group, 29% were highly-extremely highly anxious, 23% were moderately anxious, and 47% had low to normal anxiety. The correlation coefficient between GPA and test anxiety of students was -.314 which shows inverse relationship.Conclusion: Pre-exam anxiety and stress imparts negative effects on the exam performance of final year medical students. Poor academic performance was associated with high to extremely high pre-exam anxiety while high achievers had relatively lower anxiety levels.

A divergent selection experiment on environmental sensitivity was performed in rabbits. The aim of this study was to estimate the correlated response in kits’ weight and its survival, and weight distance from birth to weaning. Weight distance was calculated as the absolute values of the differences between the individual value and the mean value of its litter. Also, relationship between probability of survival at 4 d of age and weight at birth was studied. Environmental sensitivity was measured as litter size variability. A total of 2484 kits from 127 does of the low line (selected for reducing litter size variability) and 1916 kits of 114 does of the high line (selected for increasing litter size variability) of the 12th generation were weighed. Bayesian methodology was used to estimate the correlated response to selection, and LOGISTIC procedure of SAS was used to estimate the relationship between weight and probability of survival. Both lines showed similar individual weight at birth and at weaning, and similar survival at birth and at 4 d of age. Survival at weaning was higher in the low line than in the high line (0.67 and 0.62; P= 0.93). Weight distance was higher at birth but lower at weaning in the low line (47.8 g and 54.1 g; P=0.98). Kit’s weight at birth affected its survival. In conclusion, selection for environmental sensitivity showed correlated response in kits survival and in homogeneity of litter weight at weaning.

Context. During the COVID-19 pandemic, patient care was mainly organised around the hospital. Pre-hospital care has, to our knowledge, never been evaluated. Objective: To evaluate the impact of pre-hospital pathways on hospitalisation during the last part of the pandemic. Design. This was a monocentric retrospective analysis of prospectively collected medical records. Data from patients admitted to our institute between 1 February and 7 March 2022 were analysed. Main Outcome Measure(s): The primary outcomes were defined as the number of hospitalisations, resuscitations, and deaths at the time of interview and in the subsequent 30 days. The main explanatory variables were times from onset of symptoms to care, age, gender, News2 score, comorbidities, and pre-hospital pathways and their duration. Results: Three pre-hospital pathways have been identified: a pathway in which the patient consults a general practitioner for a test (PHP1); a pathway in which the patient consulted for care (PHP2); and no pre-hospital pathway and direct admission to hospital (PHP3). Factors independently associated with outcome (hospitalisation) were being male (OR 95% CI; 2.21 [1.01–4.84], p=0,04), News2 score (OR 95% CI; 2.04 [1.65–2.51], p<0.001), obesity (OR 95% CI; 3.45 [1.48–8.09], p=0.005), D-dimers > 0.5 µg/ml (OR 95% CI; 3.45 [1.47–8.12], p=0.005), prolonged time from symptoms to hospital care (PHP duration) (OR 95% CI; 1.07 [1.01–1.14], p=0.03). All things being equal, patients with a “PHP2” pre-hospital pathway had a higher probability of hospitalisation compared to those with a “PHP3” pre-hospital pathway (OR 95% CI; 4.31 [1.48–12.55], p=0.007). Conclusions. Along with recognised risk factors such as gender, News 2 score, and obesity, the patient’s pre-hospital pathway is an important risk factor associated with hospitalisation.

BACKGROUND AND PURPOSE—Atherosclerotic plaque instability and rupture in patients with asymptomatic carotid artery stenosis (ACAS) is a leading cause of major adverse cardiac events (MACE). This could be mainly evidenced in patients with pre-diabetes. Indeed, the altered glucose homeostasis and insulin resistance could cause over-inflammation of atherosclerotic plaque, favoring its conversion to unstable phenotype with rupture and MACE. Notably, the metformin therapy reducing the metabolic distress and the inflammatory burden, could lead to reduction of MACE in ACAS patients with pre-diabetes. In this setting, microRNAs (miRs) could be used as molecular biomarkers of atherosclerosis progression, plaque rupture and worse prognosis in normoglycemics (NG) vs. pre-diabetics metformin users (PDMU) vs. pre-diabetics non metformin users (PDNMU). However, the aim of our study was to investigate a wide miRNA panel in peripheral blood exosomes from patients with ACAS divided in NG vs. PDMU vs. PDNMU, and to associate the circulating miRNA expression profiles with MACE at 2 years of follow-up after endarterectomy. METHODS—The study included 234 patients with ACAS divided in NG (n 125), PDNMU (n 73) and PDMU (n 36). The miRs’ expression profiles of circulating exosomes were determined at baseline and at 2 years of follow-up by Affymetrix microarrays from plasma samples of the patients from any study cohort. Then we collected and analyzed MACE at 2 years of follow-up in NG vs. PDMU vs. PDNMU. RESULTS—prediabetics vs. NG had over-inflammation (p<0.05) and over expressed miR 24 and miR 27 at baseline. At 2 years of follow-up PDNMU vs. NG, PDMU vs. NG and PDNMU vs. PDMU over-expressed inflammatory markers and miR 24, miR 27, miR 100, miR 126 and miR 133 (p<0.05). Finally, at follow-up end we observed a significant difference about MACE comparing PDNMU vs. NG (n 27 (36.9%) vs. n 8 (6.4%); p<0.05), PDNMU vs. PDMU (n 27 (36.9%) vs. n 6 (16.6%); p <0.05), and PDMU vs. NG (n 6 (16.6%) vs. n 8 (6.4%); p<0.05). Admission glucose values (HR 1.020, CI 95% [1.001-1.038], p 0.029), atheromatous carotid plaque (HR 5.373, CI 95% [1.251-11.079], p 0.024), and miR 24 (HR 3.842, CI 95% [1.768-19.222], p 0.011) predicted MACE at 2 years of follow-up. CONCLUSIONS—Specific circulating miRs could be over-expressed in pre-diabetics and specifically in PDNMU vs. PDMU after endarterectomy. MiR24, hyperglycemia and atheromatous plaque could predict MACE at 2 years of follow-up.

In this paper, the extraction of essential oil (EO) from thyme by consecutive use of ultrasound and microwave treatments is presented. The aim of the study was to apply an ultrasound pre-treatment of thyme leaves to enhance the thymol content and the extraction yield of the EO obtained by microwave-assisted hydro-distillation (MWHD). Compared with the conventional hydro-distillation (CHD), the consecutive use of ultrasound and microwave treatments resulted in a 72% lower extraction time. When the ultrasound pre-treatment (using the ultrasonic processor with an amplitude of 70%) was applied, the EO content was 23% higher compared to the extraction without pre-treatment. The EO samples were analyzed by GC/MS. The results showed that the major component, thymol, varied from 43.54% (by CHD) to 65.94% (by consecutive use of ultrasound and microwave treatments).

This study explores the impact of the ‘pre-intervention effects’ of a community-based interventions. This refers to participatory research processes and parallel publicity in the media on changes in alcohol use and relevant mechanisms (rules and norms about alcohol, accessibility of alcohol in a formal setting) among adolescents before any intervention is implemented. In a quasi-experimental study, adolescent data were collected twice by means of self-report among adolescents living in two municipalities (control and experimental condition). Regression analysis showed pre-intervention main effects on adolescents’ perceived accessibility of alcohol in a formal setting. Moreover, among adolescents aged 15 years and older, the normative decline in strictness of rules and norms was less steep in the experimental condition compared to the control condition. Also, adolescents aged 14 years and younger in the experimental condition reported more weekly drinking compared to their peers in the control condition. No differential effects across gender were found. To conclude, applying a co-creational approach in the development of an intervention, not only contributes to more effective interventions in the end, but involvement of and discussions in the community at the start of intervention planning are contributing to changes in targeted factors. This implies that public discussions about the development of intervention strategies should be considered as an essential feature of co-creation in community-based interventions.

Dietary components are important for the structural and functional development of the brain. Among these, docosahexaenoic acid,22:6n-3 (DHA) is critically required for the structure and development of the growing fetal brain in utero. DHA is the major n-3 long-chain fatty acid in brain gray matter representing about 15% of all fatty acids in the human frontal cortex. DHA affects neurogenesis, neurotransmitter, synaptic plasticity & transmission, and signal transduction in the brain. Studies in animals and humans show that adequate levels of DHA in neural membranes are important for cortical astrocyte maturation and vascular coupling, and helps cortical glucose uptake and metabolism. In addition, specific metabolites of DHA are bioactive molecules that protect tissues from oxidative injury and stress in the brain. A low DHA level in the brain results in behavior changes and is associated with learning problems and memory deficits. In humans, the third trimester-placental supply of maternal DHA to the growing fetus is critically important as the growing brain obligatory requires DHA during this window period. Besides, DHA is also involved in the early placentation process, essential for placental development. This underscores the critical importance of maternal DHA intake for the structural and functional development of the brain. This review describes DHA's multiple roles during gestation, lactation, and the consequences of its lower intake during pregnancy and postnatally on the children's brain development and function.

Red raspberry fruit production is increasing worldwide due to the growing consumer interest in foods with high antioxidant properties. However, raspberries are very perishable fruit with a short shelf life. Chitosan applications have shown promising results in promoting the storage of different berry fruit. This work aimed at analysing the effects of chitosan applied in pre- and/or post-harvest on the quality and antioxidant properties of raspberry fruit during the cold storage and room temperature conditions (i.e., 6 d at 4 °C and 3 d at 20 °C, respectively). Pre-harvest chi-tosan applications reduced fruit weight loss during cold storage and room temperature condi-tions but also reduced fruit decay at room temperature conditions. Furthermore, pre-harvest treatments with chitosan increased the total phenol and anthocyanin contents and promoted the highest total antioxidant activity with respect to other treatments. Of note, after the cold storage, post-harvest chitosan application drastically reduced the development of fungi that cause fruit decay, thus minimizing the potential risk of mycotoxin production. Overall, this study demon-strates that applications of chitosan in pre-harvest are sufficient to ensure the goal of maintaining and/or increasing the quality and antioxidant properties of fruit during cold storage and room temperature conditions.

In this study, the effect of laser processing (LP) on the thermoelectric (TE) properties of bismuth antimony telluride (BST) alloy pellets is investigated. The stoichiometric alloy used is Bi0.4Sb1.6Te3.0, which was prepared by mechanical alloying techniques (MA) and hot pressed (HP) into pellets under optimal pressing and temperature conditions. An innovative approach to HP was also developed to enhance the yield of BST samples per HP process while maintaining the TE profiles of the samples within a variance of less than 1%. The LP process was executed by employing a metal 3D printer, with a thorough analysis of beam parameters. Notably, the laser power (P) was held constant at 25 W, along with a fixed hatching distance (HD) of 50 μm, while the parameter adjusted was the laser's scanning speed (SS), which spanned from [600 - 1800] mm/s in increments of 200 mm/s. Examination via scanning electron microscopy (SEM) revealed two material states: melted and sintered. The melted state formed the surface crust of "canyon" patterns that were held on the surface of the samples, and which both size and quantity were altered with changes in SS. For thermoelectric characterization, two distinct shapes of LP samples were produced: rectangular (for electrical properties) and disk (for thermal properties). The results demonstrated that the electrical properties are profoundly influenced by SS, with the electrical conductivity peak at SS value of 1600 mm/s, while the Seebeck coefficient reaches a minimum at the same value. Consequently, within the temperature range of interest, a notable 12% increase in electrical conductivity and a 9% decrease in the Seebeck coefficient were observed compared to the non-LP material state. Overall, the ZT value experience an 6.9% decline within the same temperature interval.

Additive manufacturing (AM) is an emerged layer-by-layer manufacturing process. However, its broad adoption is still hindered by limited material options, different fabrication defects, and inconsistent part quality. Material extrusion (ME) is one of the most widely used AM technologies, and, hence, is adopted in this research. Low-cost metal ME is a new and AM technology used to fabricate metal composite parts using sintered metal infused filament material. Since the involved materials and process are relatively new, there is a need to investigate the dimensional accuracy of ME fabricated metal parts for real-world applications. Each step of the manufacturing process, from the material extrusion to sintering, might significantly affect the dimensional accuracy. This research provides a comprehensive analysis of dimensional changes of metal samples fabricated by the ME and sintering process, using statistical and machine learning algorithms. Machine learning (ML) methods can be used to assist researchers in sophisticated pre-manufacturing planning and product quality assessment and control. This study compares linear regression to neural networks in assessing and predicting the dimensional changes of ME made components after 3D printing and sintering process. The prediction outcomes using a neural network performed the best with the highest accuracy as compared to regression. The findings of this study can help researchers and engineers to predict the dimensional variations and optimize the printing and sintering process parameters to obtain high quality metal parts fabricated by the low-cost ME process.

The violence against women is a theme that extrapolates health issues, since after a victim seek for a health care, there is the notification of the act [1]. In Brazil, many times, these women are first assisted by mobile urgency services (SAMU/SIATE) and, as far as we have concern, there are no other studies with specific data about these assistance. The present paper aimed to analyze SAMU/SIATE assistance to abused women. Qualitative and retrospective epidemiological study of assistance to assaulted women carried out by SIATE and SAMU Maringá/Norte Novo between 2011 and 2020. Women between 20 and 39 years old, non-pregnant, were the main victims, and 19,52% of them have used some kind of drug. The (ex)partner figured as the perpetrator in 17,35%, but there were no information about this variable in 73,75% of the records. The Qui-square test shows a mortality rate superior to 70% among the severe traumatized victims. This is one of the first studies to analyze this kind of care provided by SAMU/SIATE, and reveals some gaps in its “modus-operandi” that can limitate an extrapolation of the results to bigger spheres. More researches in mobile urgency care services, in other provinces also, are needed to propose strategies to fight against this epidemic.

Lymphatic filariasis (LF), also commonly known as elephantiasis, is a neglected tropical disease (NTD) caused by filarial parasites. The disease is transmitted by a bite from infected mosquitoes. The bites of these infected mosquitoes deposit filarial parasites, Wuchereria or Brugia whose predilection site is the lymphatic system. The damage to the lymph system causes swelling in the legs, arms, and genitalia. A mapping survey conducted between 2003 and 2010 determined LF that LF was endemic in Zambia in 96 out of 116 districts. Elimination of LF is known to be possible by stopping the spread of the infection through large-scale preventive chemotherapy. Therefore, mass drug administration (MDA) with diethylcarbamazine citrate (DEC) (6 mg/kg) and Albendazole (400 mg) for Zambia has been conducted and implemented in all endemic districts with five effective rounds. Post-MDA pre-transmission assessment survey (pre-TAS) was conducted between 2021 and 2022 in 80 districts to determine the LF prevalence rate. We conducted a cross-sectional seroprevalence study involving 600 participants in each Evaluation Unit (EU) or each district. The study sites (sentinel and spot-check sites) were the districts that were the Implementation Unites (IUs) where MDA, preventive chemotherapy against LF was conducted. These included 80 districts from the 9 provinces. A total of 47,235 people from sentinel and spot-check locations were tested. Of these, valid tests were 47,052 of which 27,762 (59%) were females and 19,290 (41%) were males. The survey revealed in the 79/80 endemic district a prevalence of Wb anti-gens of 0.14% and 0.0% prevalence of microfilariae. All the surveyed districts had an optimum prevalence of less than 2 percent, except for Chibombo district. The majority of participants that tested positive for Wb Ag were those that had 2, 3, and 4 rounds of MDA. Surprisingly, individuals that had 1 round of MDA were not found to have circulating antigens of Wb. The study showed that all the surveyed districts except for Chibombo, passed Pre-TAS. This further implies that there is a need to conduct a TAS in these districts in order to decide whether to stop MDA or not. Keywords: Lymphatic Filariasis; pre-TAS; Prevalence; Antigenaemia; Microfilariae; Zambia

Wild germplasm can be classified as the raw material essential for crop improvement. Introgression of wild germplasm is normally used in breeding to increase crop quality or resilience to evolving biotic and abiotic threats. Here, we explore the potential of introgressing Vaccinium elliottii into commercial blueberry germplasm. Vaccinium elliottii is a wild diploid blueberry species endemic to the southeastern United States that possesses highly desirable and economically important traits for blueberry breeding such as: short bloom to ripe period, adaptation to upland sandy soils, disease resistance, firmness, and pleasant flavor. To examine the potential of hybridization, we evaluated populations of interspecific hybrids across multiples stages of breeding (i.e., F1, F2, and backcrosses) in two crop seasons. We used our extensive pedigree data to generate breeding values for pre-breeding blueberry hybrid populations. Hybrid performance was evaluated considering fitness (i.e., plant vigor and plant height) in addition to evaluating six fruit-quality and marketable-related traits (i.e., size, firmness, acidity, soluble solids, weight, and yield). Overall, F2 and backcrosses rapidly achieved market thresholds, presenting values not significantly different from commercial blueberry germplasm. Our results confirmed the potential of exploiting the high genetic variability contained in V. elliotii for interspecific hybridization. Additionally, we developed germplasm resources that can be further evaluated and utilized in the breeding process, advancing selections for fruit quality and environmental adaptation.

Background: The world-wide rate of obesity is increasing continuously, representing a serious medical threat since it is associated with a variety of diseases including type 2 diabetes, cardiovascular disease, and numerous cancers. Sophora japonica is used as a traditional herb for medicinal purposes in eastern Asia. However, the anti-obesity effects of S. japonica fruit have not been explored. Objective: The aim of this study is to investigate the inhibition of adipocyte differentiation and adipogenesis by an ethanol extract of S. japonica fruit (EESF) in 3T3-L1 pre-adipocytes. Methods: MTT assay, Oil Red O staining, and Triglyceride contents were used to investigate lipid accumulation in 3T3-L1 cells to clarify adipocyte differentiation. The expression levels of various molecular signals associated with adipogenesis and lipogenesis were examined by western blot analysis. Results: Our results demonstrate that EESF suppressed the terminal differentiation of 3T3-L1 pre-adipocytes in a dose-dependent manner, as confirmed by a decrease in lipid droplet number and lipid content through Oil Red O staining. EESF significantly reduced the accumulation of cellular triglyceride, which was associated with a significant inhibition of the levels of pro-adipogenic transcription factors, downregulated the expression levels of adipocyte-specific proteins. Furthermore, EESF treatment effectively increased the phosphorylation of AMPK and ACC. Conclusions: These results together indicate that EESF has significant effects on the inhibition of adipogenesis and acts by stimulating the AMPK signaling pathway. Further studies will be needed to identify the active compounds in S. japonica.

Earnings management and financial distress are two critical facets of financial management in corporations that have lately been the focus of thorough research from both scholars and practitioners. The purpose of the research is to evaluate the influence of financial distress on the earnings management of companies listed at the NSE during the pre- and post-COVID eras. Multiple linear regression was applied in this study to examine the causal association between earnings management and financial distress. To assess the effect of financial distress on earnings management, the study analyzed data from 37 listed companies during the pre-COVID and post-COVID periods. The methodology also takes into account control factors like firm size, GDP, and inflation. The pre-COVID research indicates a significant positive correlation between financial strain and earnings management. In contrast, the correlation between financial distress and earnings management is not statistically significant in the post-COVID analysis. However, research shows that firm size has a statistically significant negative influence on managing earnings. The results of this study show that smaller firms are more inclined to engage in earnings management during the post-COVID era than bigger ones.

The pre-chamber technologies can improve the ignition performance of IC engines by more than two orders in magnitude and thereby substantial economic benefits. Compared with the common pre-chamber, a plug-and-play passive scheme is suitable for quick retrofit, which is getting more attention from the automobile industry. Good scavenging is the precondition for improving turbulent jet ignition performance for a passive pre-chamber. Therefore, detailed evaluations of the scavenging process and turbulent jet ignition deserve investigations for new pre-chamber schemes. In this paper, the effects of design parameters on ignition processes of plug-and-play passive pre-chamber were numerically studied, allowing for the lateral angle, orifice diameter, and vertical angle design. Seven pre-chamber schemes were evaluated, and four optimal ones were selected for bench tests. The characteristics of the scavenging process, turbulent jet ignition, and main-chamber combustion were investigated and analyzed. The results show that allowing for the trade-off between ignition energy and scavenging efficiency, the volume ratio of the pre-chamber to clearance is recommended to be 0.2~0.7%, and the corresponding area-volume ratio is 0.003~0.006 mm-1. Compared with the original natural gas engine, the pre-chamber retrofit can save up to 13.2% fuel consumption, which presents a significant improvement in fuel economy.

The introduction of tenofovir-derived prodrugs has revolutionised the prevention and management of HIV, which has coincided with 23% reduction in new HIV incidences globally. To date, there are two formulations of tenofovir-derived nucleoside reverse transcriptase inhibitor (NRTI): tenofovir disoproxil fumarate/emtricitabine (TDF/FTC) and tenofovir alafenamide fumarate/emtricitabine (TAF/FTC). Although these prodrugs have shown favourable safety profile, their effects on cardiovascular health are differ from one another: TDF/FTC exhibits potential lipid-lowering effect, TAF/FTC demonstrates potential lipid-inducing effect, which is a major risk factor for cardiovascular diseases. However, this issue has not been previously elucidated, especially among the marginalised populations [lesbian, gay, bisexual and transgender (LGBT) and men who have sex with men (MSM)] who are likely be the main users of these prodrugs. This is of clinically significance as the cardiovascular health in these populations is often overlooked, in addition to a lack of appropriate cardiovascular risk prediction algorithm. Therefore, this review aims to (1) highlight the cardiovascular risks of tenofovir-derived prodrugs in the marginalized populations, and also to (2) establish the importance of having a cardiovascular risk prediction model that is specific to this particular populations so that their health management could be more comprehensive.

High oxidative stress in cells due to inflammation process or excessive cell proliferation would produce oxidants or free radicals with biomarkers, one of which is malondialdehyde (MDA). Passion fruit seed’s contain high antioxidant and are expected to decrease the level of cholesterol and MDA. The objective is to identify the effect of passion fruit seed’s ethanol extract in Wistar rats that have been fed with atherogenic feed. The method was preclinical trial (post-test control group design) in rats, by administering passion fruit seed’s ethanol extract for 14 days. This study used 26 male rats aged two months, divided into 5 groups. The result showed significant difference in MDA level which was found in group that was given passion fruit seed extract 10mg/kg BW with positive control group that was given standard feed. Passion fruit seed’s extract showed significant difference in level of triglyceride, which was found in negative control group that was given atherogenic feed with group that was given passion fruit seed’s extract 5mg/kg BW (mean±standard deviation: 1.09±0.30 mg/dL vs 0.77±0.25mg/dL; p=0.048). This study showed that passion fruit seed’s ethanol extract had significant lowering effect in level of MDA, total cholesterol, and triglyceride for 14 days.

Neuromonitoring of the efferent nerve impulses transmission in the spinal cord tracts during surgical scoliosis treatment makes it possible to assess whether the functional status is deteriorating, affecting the procedure's safety. Is there any relationship between pre- and intraoperative motor evoked potentials recordings and does idiopathic scoliosis (IS) surgical correction improve directly the spinal efferent transmission? This study aimed to compare the results of surface recorded electromyography (EMG), electroneurography (ENG, M and F-waves), and especially motor evoked potentials (MEP) from tibialis anterior (TA) muscle bilaterally in 353 girls with the right idiopathic scoliosis (types 1A-4C according to Lenke classification). It has not yet been documented whether the results of MEPs recordings induced by transcranial single magnetic stimulus (TMS, pre – and postoperatively) and trains of electrical stimuli (TES; intraoperatively in T0-before surgery, T1 – after pedicle screws implantation, T2 – after scoliosis curvature distraction and derotation following two rods implantation) can be compared for diagnostic verification of improvement of the spinal neural transmission. The study also attempted to determine whether the constant level of optimal anesthesia during the certain surgical steps of scoliosis treatment affects the parameters of MEPs recorded during neuromonitoring procedures. No neurological deficits have been observed postoperatively. Values of amplitudes but not latencies in MEPs recordings evoked with TMS in IS patients compared before and after surgery indicated a slight improvement in the efferent transmission of neural impulses within the fibers of the spinal tracts postoperatively. Results of all neurophysiological studies in IS patients were significantly asymmetrical and recorded worse on the concave side, suggesting greater neurological motor deficits at p=0.04. This asymmetry had been significantly reduced following IS surgery. The surgeries in IS patients brought significant improvement (p=0.04) in parameters of amplitudes of sEMG recordings, however reflecting still the consequences of the neurogenic injury of TA muscle motor units. ENG studies results indicated the symptoms of the axonal type injury in peroneal motor fibers improved only on the concave side at p=0.04 in parallel with the significant improvement of F-waves parameters, which suggests that surgeries might result in the lumbar ventral roots decompression. There were not detected significant differences in amplitudes or latencies of MEPs induced with TMS or TES comparing the parameters recorded preoperatively (one day before surgery) and intraoperatively in T0. The amplitudes of TES evoked MEPs increased gradually at p=0.04 in the subsequent periods (T1 and T2) of observation. The significant reduction of MEPs latency at p=0.05 was observed only at the end of the IS surgery. Studies on the possible connections between the level of anesthesia fluctuations and the required TMS stimulus strength, as well as the MEPs amplitude changes measured in T0-T2 revealed lack of relationships. It is not likely that they could be the factors influencing the efferent transmission in spinal pathways beside the surgical procedures. Considering that MEPs amplitude parameter reflects the number of axons excited from the motor cortex and transmitting the efferent impulses via spinal descending tracts in the white matter, pre- (TMS evoked) and intraoperative (TES evoked) recordings are reliable for evaluating the patient’s neurological status before and during surgical scoliosis correction procedures. The results of this study indicate an agreement between preoperative and early-intraoperative evaluations with these both diagnostic methods. An increase of MEPs amplitude parameters recorded on both sides after scoliosis surgery proves immediate improvement of the total efferent spinal cord transmission. Considering comparative pre- and postoperative sEMG and ENG recordings it can be concluded that surgeries might directly result in the additional lumbar ventral roots decompression. Our results of the tests on the possible variability of the anesthesia level on the parameters of intraoperative recorded MEPs show no clear relationships. We can conclude that MEPs parameters changes are determined by the surgery procedures during neuromonitoring, not the anesthesia conditions if they are kept stable, which influences a decrease in the number of false-positive neuromonitoring warnings. Further studies on a larger population of patients with long-lasting observation postoperatively are required to confirm the presented conclusions on the direct influences of scoliosis surgery on improvement of the motor function in patients with IS.

Artificial intelligence (AI)-based models hold the potential to transform higher education if adopted properly and ethically. A prime example is ChatGPT with earlier studies indicating its widespread adoption in academia and by university students. The current study aimed to identify the factors influencing the attitude towards ChatGPT and its usage among university students in Arab countries. A previous survey instrument termed Technology Acceptance Model Edited to Assess ChatGPT Adoption (TAME-ChatGPT) was administered online using a convenience-based approach among the contacts of the authors. Confirmatory factor analysis (CFA) for the survey constructs was done using root mean square error of approximation (RMSEA), standardized root mean square residual (SRMR), comparative fit index (CFI), and Tucker-Lewis index (TLI). The final study sample comprised a total of 2240 participant divided as follows: Iraq (n=736, 32.9%), Kuwait (n=582, 26.0%), Egypt (n=417, 18.6%), Lebanon (n=263, 11.7%), and Jordan (n=242, 10.8%). A total of 1048 respondents heard of ChatGPT before the study (46.8%), of which 551 used ChatGPT (52.6%). The mean scores of TAME-ChatGPT constructs showed that the ease of ChatGPT use, positive attitude towards technology and social influence, higher perceived usefulness, the influence of behavioral/cognitive factors, low perceived risks and low anxiety were the determinants of positive attitude to ChatGPT and its use. For both the attitude and usage scales of TAME-ChatGPT, CFA collectively yielded satisfactory fit indices as indicated by low RMSEA and SRMR together with high CFI and TLI. Multivariate analysis showed that attitude to ChatGPT use was significantly influenced by country of residence, age, university type, and the latest grade point average of the students. The current study confirmed the validity of TAME-ChatGPT as a survey instrument to assess the possible determinants of ChatGPT use among university students in Arab countries. The study findings highlighted that successful adoption of ChatGPT in higher education could be dependent on perceived ease of use, usefulness, positive attitudes to technology, social influence, behavioral/cognitive factors, lower anxiety, and minimal perceived risks. The utility of ChatGPT in higher education requires policies that should be tailored for various settings, considering the differences observed in attitude towards ChatGPT among participating students in this study.

Polycystic ovary syndrome (PCOS) is a multisystem disorder that presents with a variety of phenotypes involving metabolic, endocrine, reproductive, and psychological symptoms and signs. Women with PCOS are at increased risk of pregnancy complications including implantation failure, miscarriage, gestational diabetes, fetal growth restriction, preterm labour, and preeclampsia (PE). This may be attributed to the presence of specific susceptibility features associated with PCOS before and during pregnancy, such as chronic systemic inflammation, insulin resistance (IR), and hyperandrogenism, all of which have been associated with an increased risk of pregnancy complications. Many of the features of PCOS are reversible following lifestyle interventions such as diet and exercise, and pregnant women following a healthy lifestyle have been found to have a lower risk of complications, including PE. This review summarizes the evidence investigating the risk of PE and the role of nutritional factors in women with PCOS. The findings suggest that the beneficial aspects of lifestyle management of PCOS, as recommended in the evidenced-based international guidelines, extend to improved pregnancy outcomes. Identifying high-risk women with PCOS will allow targeted interventions, early pregnancy screening, and increased surveillance for PE. Women with PCOS should be included in risk assessment algorithms for PE.

Based on the teaching material of "Robotics" course, this paper studied the automatic knowledge graph construction, including knowledge points extraction and knowledge point relation extraction. We proposed a new method of extracting the first-level, second-level, and third-level knowledge points as well as their prerequisite relations of knowledge points in the textbook. For the problem of insufficient knowledge of the pre-trained language model in the specific field, methods such as incremental pre-training and optimization of cost functions are employed to integrate subject knowledge into the pre-trained language model, thus improving its effectiveness. To overcome the problem that the traditional method of relationship extraction can not be applied directly to the extraction of teaching materials, a new scheme for knowledge point relationship extraction based on keyword relationship is proposed. The experimental data from textbooks shows that the F1 score of knowledge point extraction reaches 93%, considerably improved compared to the traditional model. Consequently, the knowledge point entity extraction and relationship extraction methods based on the pre-trained model can effectively extract structured information and facilitate the automatic construction of knowledge graphs.

MicroRNAs (miRNAs) are crucial regulatory RNAs, originated from hairpin precursors. For the past decade, researchers are focusing extensively on miRNA profiles in various plants. However studies on precursor miRNAs (pre-miRNAs) global profiling stay static even in model plants. Here, for the first time in a non-model plant, Abelmoschus esculentus with negligible genome information, we are reporting the global profiling to characterize the miRNAs and their associated pre-miRNAs by applying next generation sequencing approach. Preliminarily we performed sRNA (small RNA) sequencing with five biological replicates of leaf samples to attain 207,285,863 reads and data analysis using miRPlant keyed out 128 known and 845 novel miRNA candidates. With the objective to seize their associated hairpin precursors, we accomplished pre-miRNA sequencing to attain 83,269,844 reads. The paired end reads are merged, adaptor trimmed and the resulting 40-241 nt (nucleotide) sequences were picked out for analysis by using perl scripts from miRGrep tool and in-house built shell script for Minimum Fold Energy Index (MFEI) calculation. Applying stringent criteria of dicer cleavage pattern and perfect stem loop structure revealed precursors for 57 known miRNAs of 15 families and 18 novel miRNAs. Quantitative Real Time (qRT) PCR was performed to determine the expression of selected miRNAs.

Lattice structures have emerged as promising materials for aerospace structures applications due to their high strength-to-weight ratios, customizable properties, and efficient use of materials. These properties make them at-tractive for use in anti-ice systems, where lightweight and heat exchanging are essential. This paper presents an extensive experimental investigation into mechanical compression properties of lattice trusses fabricated from AlSi10Mg powder alloy, a material commonly used in casted aerospace parts. The truss structures were manufactured using additive manufacturing Selective Laser Melting technique and subjected to uniaxial compressive loading to assess their performance. The results demonstrate that AlSi10Mg lattice trusses exhibit remarkable compressive strength with strong correlations depending upon both topology and cells’ parameters setup. The finding described highlights the potential of AlSi10Mg alloy as a promising material for custom truss fabrication, offering customizable cost-effective and lightweight solutions for aerospace market. The paper also emphasizes the role of additive manufacturing in producing complex structures with pointwise tailored mechanical properties.