A novel five-surface phosphor-in-ceramic (FS-PiC) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiC LEDs. The performance of the FS-PiC LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-ceramic (SS-PiC) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiC LEDs was higher than the SS-PiC LEDs for illumination, CCT, and CIE of 1.1, 7, and 23 times, respectively. Furthermore, the FS-PiC LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiC larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

Phosphors based on magnesium titanate activated with Mn⁴⁺ ions are of great interest because, when excited with blue light, they display a strong red-emitting luminescence. They are characterized by a luminescence decay which is strongly temperature dependent in the range from 0 to 80 °C, making these materials very promising for temperature sensing in the biochemical field. In this work the optical and thermal properties of the luminescence of Mg₂TiO₄ are investigated for different Mn⁴⁺ doping concentrations. The potential of this material for temperature sensing is demonstrated by fabricating a fiber optic temperature microsensor and by comparing its performance against a standard resistance thermometer. The response of the fiber optic sensor is exceptionally fast, enabling monitoring of temperature fluctuation in subsecond time domain.

Electroluminescence (EL) is an innovative technology in the lighting area. The EL device's main structure consists of a phosphor layer sandwiched by two electrodes. In this work, several alternating current EL devices have been developed by applying a set of sequential layers with combinations of in-house prepared inks and commercially available ink as a phosphor layer. A flexible polyester textile substrate was functionalized with inks by spray coating technique, after knife-coated an interfacial layer directly on the surface. A thorough study was carried out on the phosphor layer composition to optimize the EL device performance, more precisely the illuminance intensity and the illuminance homogeneity. The developed phosphor layer was composed of zinc sulphide doped with copper (between 30.0 to 38.1 wt%) and diluted by using a diluent at different ratios (28.0 to 35.5 wt%). The best peak illuminance intensity of 61 lux was obtained when the phosphor ink presented 35.4% ZnS:Cu and was diluted with 33.0% diluent. The aim of this study to determine the best formulation of the phosphor layer, which can be highly promising for further developments of EL devices, taking in account different applications in market.

Spectroscopic methods are used to study the processes of accumulation of electron and hole trapping centers and energy transfer of electronic excitations to impurities in CaSO4-Mn and BaSO4-Mn. It is shown that the transfer of energy from the host to impurities occurs at the moment of charge transfer from the excited anionic complex SO_4^(2-) to the hybrid radiative electronic states at 2.95–3.1 eV formed from the electronic states of the Mn^(+)-SO_4^(-) and SO_4^(3-)-SO_4^(-) trapping centers. It was found that, in sulfates, under irradiation, as a result of charge transfer from excited anionic complexes of the host to the excited states of impurities Tl^(+),Cu^(+),Mn^(2+), hybrid radiative states emerge at 2.95–3.15 eV, occupying the same energy levels as the intrinsic electronic trapping center SO_4^(3-) of the host at 2.95–3.1 eV.

A series of Eu³⁺ doped CaSiO₃/SiO₂ nano-phosphor powder of controlled grain size, crystalline structure, and chemical composition were synthesized using the microemulsion technique. XRD profiles of samples sintered over 600 of suggested phase shift from amorphous powder grain to more ordered polycrystalline powder of triclinic type wollastonite, CaSiO₃, with preferred crystal phase orientation of (112) and tetragonal type cristobalites of SiO₂. The grain size, crystallinity, and chemical composition of the host matrix, activator and sensitizer strongly affected both the absorption and emission bands of these samples. The amplitude of both the orange and red emission bands significantly increased with sintering temperature. The emission band is red-shifted with decreasing grain sizes. These bands displayed good sensitivity to ionic concentration of the Si⁴⁺, Ca²⁺, and Eu³⁺. With increasing Ca²⁺ ion concentration both the intensity of the red photoluminescence (PL) band increased and a concentration quenching observed. Increase in Si⁴⁺ ion concentration led to quenching in PL intensity of both the orange and red bands whereas the amplitude of the blue-band slightly increased. With increasing Eu³⁺ ion concentration the red-band initially increased whereas it started decreasing at higher sample concentration. In the presence of Ca²⁺ ion as a sensitizer, the sample showed a remarkable PL property—including—about 100% photon conversion efficiency and a two-fold increase in excitation and emission photons.

Although CAD/CAM ceramics present a promising alternative to metal-ceramic fixed dental prostheses, little is known about their mid- and long-term clinical performance. This systematic review aims to estimate the survival and success rates and describes the underlying complication characteristics for CAD/CAM tooth-supported fixed dental prostheses (FDPs). We systematically searched MEDLINE and Web of Science to find relevant prospective studies with a follow-up of at least one year. We estimated pooled 1-, 5- and 10-year survival and success rates by combining the collected data in a Poisson regression model. Descriptive statistics were conducted to evaluate the distribution of failures and complications in the included studies. Risk of bias for the included studies was assessed with an adapted checklist for single-arm trials. Pooled estimated 1-, 5-, and 10-year survival rates ranged from 93.80% to 94.66%, 89.67% to 91.1%, and 79.33% to 82.20%, respectively. The corresponding success rates, excluding failures but including any other types of intervention, were 94.53% to 96.77%, 90.89% to 94.62%, and 81.78% to 89.25%. Secondary caries was the most frequent cause of failure, followed by chipping of the veneering. The most common cause of complication, excluding failures but requiring intervention, was chipping of the veneering. Risk of bias was generally acceptable for the included studies, with 7 studies associated with low risk of bias, 8 studies with a moderate risk of bias, and 3 studies with serious risk of bias. The current meta-analysis on CAD/CAM supported FDPs revealed satisfying survival and success rates for up to 10 years of exposure. More prospective studies focusing on long-term performance are needed to strengthen the evidence currently available in the literature.

Electron beam treatment of ZnS:Cu,Br (Cu activator content 0…0.6%wt.) radioluminescent phosphors as well as charge mixture with the electron energy 900 keV and absorbed dose of 600 kGy resulted in a enhancement of brightness up to 80%. The increased brightness is due to increase of content of wurtzite phase relative to sphalerite one with formation of wurtzite/sphalerite nanocomposite structure. Transformation of crystal structure is accompanied with corresponding change in content of active surface centers characteristic for sphalerite and wurtzite phases. A model describing surface centers of ZnS:Cu,Br radioluminescent phosphor is suggested.

Nanotechnology is concerned with the creation of particles and materials at nanoscale levels. Nanocomposite is a combination or matrix, in which different materials combine to develop new properties of the materials ensuring that one of the materials have size in range of 1-100 nm. Nanocomposites are classified according to the types of reinforcement materials and matrix materials used in their construction. Nanocomposites are divided into three types based on the matrix material: ceramic matrix nanocomposites (CMNC), polymer matrix nanocomposites (PMNC), and metal matrix nanocomposites (MMNC) (MMNC). The synthetic methods of nanocomposites are frequently classified in to two classes. These are top-down and bottom up approaches. The type of synthetic technique used is determined by the nanocomposites' intended properties. There are different wet methods for synthesis of metal nanoparticles and nanocomposites among these co-precipitations, sol gel and hydrothermal methods are cost effective as compared to other methods. The synthesized nanocomposites can be characterized using different techniques to get insight into the morphology, particle size, phase, composition, thermal stability, optical, magnetic, electrical and thermal properties. Also, nanocomposites are used in medical, pharmaceutical industry, food packaging, to electronics and energy industry. Thus this review focuses on the main ideas about synthesis, characterization and application of nanocomposites.

Franklinite-Zincochromite-Gahnite solid solutions have been prepared by ceramic or coprecipitation method and its pigmenting capacity as cool ceramic pigments in different glazes (double and single firing frits and porcelain frit) was studied. XRD, UV-Vis-NIR diffuse reflectance, CIEL*a*b* colour analysis, bandgap measurement and the photocatalytic activity over the Orange II azoic dye were carried out for the characterization of samples. Following criteria of high red colouring capacity and high NIR reflectance at minimum Cr amount, Zn(Fe1.8Cr0.2), Zn(Al1.5Cr0.5) and Zn(Al1.3Cr0.5Fe0.2)O4 turn out to be the optimal compositions for an intense reddish cool pigment. All powders show a direct semiconductor behaviour with bandgap around 2 eV, falling in the visible range (620 nm), and according to literature, the associated photocatalytic activity over Orange II with visible light irradiation is moderate in all cases, but the Franklinite-Zincochromite Zn(Fe1.8Cr0.2) stands out.

Hip joint surgeries, including total hip replacement or resurfacing, have increased tremendously in the last decades. Number of patients of all ages, replace their hip, due to severe injuries or trauma problems, so as to have a better life. According to these factors, new material and processes in implants manufacturing are imported to medicine, through research programs, every year. In the scope of one of these programs, that has to do with ceramic coatings on metallic resurfacing implants, a new 3axis Hip simulator was designed and manufactured in the Laboratory of Manufacturing Technology of the National Technical University of Athens. The scope of this paper is to present the main parts, materials and process used to manufacture the simulator as well as the way the simulator is working and how its movement in 3axis is accomplished. Furthermore, the evaluation of the machine and its use to examine resurfacing implants is presented.

The objective was to compare the failure loads of glass ceramic, and polymer crowns against yttria-partially stabilized zirconia (Y-PSZ) crowns with varying yttria concentrations. Monolithic crowns of zirconia (Cercon XT, Katana UTML, BruxZir Anterior), glass ceramic (Celtra press, IPS e.max press, Lisi press), and polymeric materials (Trilor, Juvora, Pekkton) were fabricated and cemented to epoxy abutments. The total number of specimens was 135 for crowns and 135 for discs (15 specimens per material type and design). A universal testing machine was used to perform compressive loading of all crowns to failure with a steel hemisphere along the longitudinal axis of the abutments. Energy dispersive spectroscopy (EDS) was used to identify the concentration (mol% yttria-partially stabilized zirconia) for each zirconia brand. The data were analyzed using a generalized linear model and regression analysis. The results revealed significant differences (P < .05) in mean failure loads for different crown materials: Trilor (6811 ± 960 N) > Juvora (5215 ± 151 N) > Cercon (4260 ± 520 N) = BruxZir (4186 ± 269 N) = e.max (3981 ± 384 N) > Katana (3195 ± 350 N) = Lisi (3173 ± 234 N) = Pekkton (3105 ± 398 N) > Celtra (2696 ± 393 N). EDS showed that the zirconia materials contained yttria at different concentrations (BruxZir = 5Y-PSZ, Cercon = 4Y-PSZ, Katana = 3Y-PSZ). The yttria concentration had a significant effect on the failure load of the Katana (3Y-PSZ) crowns, which revealed lower failure loads than the Cercon (4Y-PSZ) and BruxZir (5Y-PSZ) crowns. New zirconia materials are provided with different yttria concentrations (3Y-, 4Y-, and 5Y-PSZ). Since a higher yttria concentration increases the translucency, clinicians should be aware that 4-5 wt% yttria-partially stabilized zirconia materials provide comparable or higher mechanical properties than e. max glass ceramic for dental application of crowns.

This report aimed to know the performance of local mineral-based composite ceramic. The materials used consist of Indonesian local minerals, which are jarosite and manganite minerals as sources of oxide iron and Mangan. The materials were synthesized using the precipitation method, whereas composite ceramic was fabricated using a screen printing method and fired at 600 oC using a furnace. The results of the characterizations indicate that the sample forms three phases on diffraction peaks. The differences in the resistance values in ambient and ethanol environments indicate that the sample has very different responses. The high porosity of the sample greatly support the gas adsorption process. Thus, the sample has a high level of sensitivity. With the above characteristics, the composite ceramic which was fabricated has the potential to be applied to gas sensors, especially ethanol gas sensors.

In precision agriculture in fertigated crops it is necessary to optimize the use of water and chemicals, and enable efficient application of fertilizers in order to ensure the best yield and avoid risks of soil salinization and contamination. In this study, an intelligent system was developed with the objective of monitoring, in real-time, moisture and solute concentrations in soil cultivated with lisianthus (Eustoma grandiflorum, var. Casablanca) fertigated under a protected environment. During one crop cycle, moisture was monitored in soil solution using TDR100 reflectometer and solute concentrations were monitored with ceramic cup extractors. Plants were fertigated with a solution containing five potassium concentrations (50, 100, 150, 200, and 250 mg dm-3) applied when the soil reached moisture limits of 0.20, 0.15, 0.13, 0.11, and 0.09 cm3 cm-3. Experimental plots were arranged in a randomized block design in a 5 x 5 factorial scheme (moisture limits x potassium concentrations in soil solution), with four replicates. The proposed intelligent system enabled precise monitoring of moisture and electrical conductivity by TDR, and potassium, and other solute concentrations with extractors, being indicated for the management of lisianthus fertigation under greenhouse conditions with greater environmental safety and reduction of water consumption and risk of salinization.

This study provides a novel method to prepare metal-ceramic composites from magnetically selected iron ore using microwave heating. By introducing three different microwave susceptors (Activated Carbon, SiC, and a mixture of Activated Carbon and SiC) during the microwave process, effective control of the ratio of metallic and ceramic phases has been achieved easily. The effects of the three susceptors on the microstructure of the metal-ceramics and the related reaction mechanisms were also investigated in detail. The results show that the metal phase (Fe) and ceramic phase (Fe2SiO4, FeAl2O4) can be maintained, but the metal phase to ceramic phase changed significantly. In particular, the microstructures appeared as well-distributed nanosheet structures with diameters of ~400 nm and thicknesses of ~20 nm when SiC was used as the microwave susceptor.

The aim of this study is to evaluate the optimal conditions of membrane filtration process. Both laboratory test and pilot-scale test were conducted to examine a treated water on blending water. The water sample were prepared by blending a raw water and the effluent water filtered through an organic membrane. The optimal efficiency in the treatment of water quality at the lab-scale test was generated under conditions of flux at 2.0 m³/m²∙day, the blending ratio of 4:1, and the optimal dosage of coagulant at 20 ppm. The pilot-scale test resulted in that the optimal efficiency was obtained under conditions of flux at 2.0 m³/m²∙day and the blending ratio of 6.0:1. However, the different results between lab-scale and pilot-scale tests on the optimal dosage of coagulant implied that it is difficult to achieve the stable condition of process operation at the low level of coagulant. In summary, the results indicated that, in the combination process of organic membrane and ceramic membrane, the recovery efficiency was achieved above the level of 98.4 %. Compared to 92.1 % in a single organic membrane process, the combination process is 6.3 % more efficient than the single one. This combination process of water treatment lead to stable recovery rates by the optimal input of dosage, less pollution load to water, and a stabilized filtration system.

Talking about sustainable development refers mainly to the environmental sphere, but the concept is much broader and also takes into account the social and economic conditions. The concept of sustainability, in this sense, is linked to the compatibility between the development of economic activities, the related social phenomena, and the protection of the environment. Therefore, the ability to balance social, economic and environmental sustainability is the very meaning of the concept of sustainable development. Firms that choose to develop policies and strategies to enhance and pursue sustainable development in the medium to long term have the burden of having to quantitatively document the improvements in production processes with the aim of sustainable development. As a result, one of the biggest challenges for European industry is to introduce sustainability principles into business models leading to competitive advantage. This is particularly important in raw material and energy intensive manufacturing sectors such as the ceramic industry. The present state of knowledge lacks a comprehensive operational tool for industry to support decision-making processes geared towards sustainability. In the ceramic sector, the economic and social dimensions of the product and processes have not yet been given sufficient importance. Moreover, the traditional research on industrial districts lacks an analysis of the relations between firms and the territory with a view to sustainability. Finally, the attention of scholars in the field of economic and social sustainability, has not yet turned to the analysis of the Sassuolo district. Therefore, in this paper we introduce the Life Cycle Sustainability Assessment (LCSA), as a method that can be a suitable tool to fill this gap, because through a mathematical model it is possible to obtain the information useful for decision makers to integrate the principles of sustainability both at the microeconomic level in enterprises, and at the meso-economic level for the definition of economic policies and territorial governance. Environmental and socio-economic analysis was performed from the extraction of raw materials to the packaging of the product on different product categories manufactured by the Italian ceramic industries of the Sassuolo district (northern Italy). For the first time the LCSA model, usually applied to unitary processes, is extended to the economic and industrial activities of the entire district, extending the prospect of investigation from the enterprise and its value chain to the integrated network of district enterprises.

In this work SiC-Ti3AlC2 and TiC-Ti3AlC2 composites produced by additive manufacturing are investigated. The fused granules fabrication (FGF) method as one of the material extrusion additive manufacturing (MEAM) technology is used to obtain composite samples. Composites with different ratios between components and different powder:polymer ratios are investigated. The technological features of the additive formation of composites are investigated, as well as their structure and properties. The optimal sintering temperature to form the best mechanical properties for both composites is 1300 °C. The composites have a regulatable porosity. Ti3AlC2 content, sintering temperature, and polymer content in the feedstock are the main parameters that regulates the porosity of FGF samples.

Due to the high temperature limitation associated with silicon, SiC, Si₃N₄, TiC, TiN, TiB₂, cBN, CNx, SiO₂, Al₂O₃ and novel multicomponent nanocomposites polymer derived ceramics (PDC) based thin films like Si-C-N, Ti-Si-B-C-N and Si-O-CN that are compatible with silicon and have a wider range of operation in ambient conditions are being investigated. Apart from small scale electro-mechanical devices like N/MEMS, sensors, areas like metallurgical protection, water purification, energy storage, bio medical implants and aerospace have been benefited. The cross-sectional study involving the role of oxygen and nitrogen dissolution at different interfacial configurations has been presented.

Hip replacement has significantly improved the quality of life of patients with symptomatic hip osteoarthritis. Metal-on-metal (MoM) bearings have been used with conventional total hip re-placement (THR) for several decades with promising results from early applications. Wear and corrosion of these implants may lead to a release of metal products into surrounding tissue and body fluids. From the 1980s onwards, the search for increasingly better coupling materials with low levels of wear led to the rise of hard-on-hard couplings such as ceramic-on-ceramic (CoC). The latter is currently the coupling with the longest known duration and with a wear rate close to zero. MoM coupling has been for a long time the most significative alternative, but systemic and local complications linked to the release of chromium and cobalt ions, determine the withdrawn from the market. One other alternative proposed over the time has been Ceramic-on-Metal (CoM) bearing. Preliminary results have been described as favourable, but due to the failures of metal on metal it has been withdrawn from the market, without causing significant clinical complications. In this narrative review, we analysed risks and benefits associated with the implantation of hybrid hard-on-hard bearings, such as CoM.

The current paper is focused on the rapidly developing field of nano-/micro three-dimensional production of inorganic materials. The fabrication method includes laserlithography of hybrid organic-inorganic materials with subsequent heat treatment lead-ing to a variety of crystalline phases in 3D structures. In this work, it was examineda series of organometallic polymer precursors with different silicon (Si) and zirconium (Zr) molar ratios, ranging from 9:1 to 5:5, prepared via sol-gel method. All mixtureswere examined for perspective used in 3D laser by manufacturing by fabricating nano-and micro-feature sized structures. Their deformation and surface morphology wereevaluated depending on chemical composition and crystallographic phase. The appear-ance of a crystalline phase was proven using single-crystal X-ray diffraction analysis,which revealed a lower crystallization temperature for microstructures compared tobulk materials. Fabricated 3D objects retain a complex geometry without any distortion after heat treatment up to 1400^oC. Under the proper conditions, a zircon phase (ZrSiO₄ - a highly stable material) can be observed. In addition, the highest newrecord of achieved resolution below 60 nm has been reached. The proposed prepara-tion protocol can be used to manufacture micro/nano-devices with high precision andresistance to high temperature and aggressive environment.

Acoustic emission (AE) has proven to be a very useful technique for determining damage in ceramic matrix composites (CMCs). CMCs rely on various cracking mechanisms which enable non-linear stress-strain behavior with ultimate failure of the composite due to fiber failure. Since these damage mechanisms are all micro-fracture mechanisms, they emit stress waves ideal for AE monitoring. These are typically plate waves since for most specimens or applications one dimension is significantly smaller than the wavelength of the sound waves emitted. By utilizing the information of the sound waveforms captured on multiple channels from individual events, the location and identity of the sources can often be elucidated. The keys to the technique are the use of wide-band frequency sensors, digitization of the waveforms (modal AE), strategic placement of sensors to sort the data and acquire important contents of the waveforms pertinent for identification, and familiarity with the material as to the damage mechanisms occurring at prescribed points of the stress history. The AE information informs the damage progression in a unique way which adds to the understanding of the process of failure for these composites. The AE methodology was applied to composites tested in fatigue at different frequencies where identification of when and where AE occurred coupled with waveform analysis leads to source identification and failure progression.

Ceramic composites have good strength, fracture toughness and hardness characteristics and are widely used in industry, medicine. The properties of ceramic composites can be controlled at the production stage by setting the internal structure. This is made possible by the development of additive manufacturing. However, not all properties are well understood, especially dynamic fracture resistance and fracture toughness. In order to predict the mechanical behavior of ceramic composites in the manufacturing phase with a controlled structure under dynamic loads, it is convenient to use methods of numerical analysis. The aim of this work was to investigate the influence of loading speed and internal structure on dynamic resistance and fracture toughness of ATZ nanocomposites. Within the framework of the study physical and mathematical model that is used in computational mechanics of materials is developed. In the paper is shown the influence of the loading rate on the strain rate in the region of the shock transition for materials based on ZrO2 - Al2O3 system. The research shows nonlinear effects under intense dynamic loads in the shown composite materials are bound up with either the processes of self-organisation of deformation modes at the mesoscopic level or the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

The plastic deformation behavior of 3Y-TZP with weak electric current in oxygen-lean atmosphere was investigated. An electrochemical reduction reaction, induced by the electric current, can significantly promote the plastic deformation of 3Y-TZP at furnace temperature of 1200 °C and a strain rate of 6.67 × 10−4 s−1. Especially, a remarkable variation of the electrical property and grain growth were observed in 3Y-TZP during the deformation. The stress exponent ranging within 2~3 indicated that the deformation was dominated by grain boundary sliding. The applied electric current decreased the apparent activation energy Q of the deformation from 465 kJ mol-1 to 315 kJ mol-1, resulting in a transition of the diffusion mechanism from the lattice diffusion to the grain boundary diffusion. These phenomena were mainly attributed to the enhancement of the cation diffusion caused by the electrochemical reduction reaction, which induced by the electric current in oxygen-lean atmosphere.

This paper presents a physical and mathematical model that has been developed in the framework of the approach used in the computational mechanics of materials. The model is designed to enable the study of the patterns of deformation and fracture of ceramic composites with a transformation-hardened matrix that are obtained by additive technologies at the mesoscopic and macroscopic levels under intense dynamic loading. The influence of the loading rate on the formation of the fracture and energy dissipation fronts for composite materials, based on the Al2O3 20%ZrO2 system, is shown. Nonlinear effects under intense dynamic loading in the considered composites are associated with the processes of self-organization of structural fragments at the mesoscopic level, as well as the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

The aim of this study was to investigate the possibility of a freeform fabrication of porous ceramic parts through selective laser sintering (SLS). SLS was proposed to manufacture ceramic green parts because this additive manufacturing technique can be used to fabricate three-dimensional objects directly without a mold, and the technique has the capability of generating porous ceramics with controlled porosity. However, ceramic printing has yet fully achieved its 3D fabrication capabilities without using polymer binder. Except for the limitation of high melting point, brittleness and low thermal shock resistance from instinct ceramic material properties, the key hurdle lies on very poor absorptivity of oxide ceramics to fiber laser which is widely installed in the commercial SLS equipment. An alternative solution to overcome the poor laser absorptivity via improving material compositions was presented in this study. The positive effect of carbon additive on the absorptivity of silica powder to fiber laser will be discussed. To investigate the capabilities of the SLS process, 3D porous silica structures were successfully prepared and characterized.

The effects of the additives (silicon carbide and titania) and sintering temperatures on the phases developed, physical and mechanical properties of sintered mullite-carbon ceramic composite produced from kaolin and graphite was investigated. The kaolin and graphite of known mineralogical composition were thoroughly blended with 5 and 3 (vol.) % silicon carbide and titania respectively. From the homogeneous mixture of kaolin, graphite and titania, standard samples were prepared via uniaxial compaction. The test samples produced were subjected to firing (sintering) at 1300˚C, 1400˚C and 1500˚C. The sintered samples were characterized for the developed phases using x‐ray diffractometry analysis, microstructural morphology using ultra‐high resolution field emission scanning electron microscope (UHRFEGSEM). Various physical and mechanical properties were determined. It was observed that the addition of SiC/TiO2 additives to the samples made them to possess very low oxidation indices .This also resulted in improvement in the bulk densities and cold crushing strength of the sample when compared with those without additives. It was concluded that the addition of SiC/TiO2 additives improves on the high temperature oxidation resistance of the mullite-carbon ceramic composite sample.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

Present research focus on the effect of different processing routes on physical and mechanical properties of nano Ti(CN) based cermet’s with metallic binders. Tungsten carbide (WC) is added as secondary carbide and Ni-Co are added as metallic binders in nano Ti(CN) based cermet processed via Conventional and Spark Plasma Sintering (SPS). Systematic comparison of composition and sintering conditions for different cermet’s’ systems is done to design the novel composition and sintering conditions. Nano TiCN powder was prepared by 30hr of ball milling. Highest density of >98.5% percent was achieved for SPS processed cermet’s sintered at 1200°C and 1250°C for 3 min. at 60 MPa pressure in comparison to conventionally sintered cermet’s at 1400°C for 1hr with two stage compaction process, uniaxially at 150 MPa and isostatically at 300 MPa pressure respectively. Comparison of XRD analysis of milled powders of different time intervals was done to understand the characteristics of the as received and milled powders. Peak broadening was observed after 5 hr. of ball milling, and it increased till 30hr. Also, peak broadening and refined carbide size was observed in XRD and SEM micrograph of SPS processed cermet. TEM analysis of milled powder showed internal structure having regular periodic arrangement of planes. SEM (BSE) images of all cermets primarily showed three major microstructural phases of core-rim-binder with black, grey and white contrast respectively. In the present sintering conditions high hardness of ~16 GPa and fracture toughness of ~9 MPa m1/2 was obtained for SPS processed cermets sintered at higher temperature.

The ceramic pastes of ca. 31 samples recovered from the Almaraz archaeological site, located in the south bench of Tagus River, were studied in detail using XRF, micro-Raman and GSDR spectroscopies, as well as the XRD technique. The ceramic sherds could be grouped into six categories, Red Slip tableware, Decorated tableware, Yellow Slip tableware, Grey tableware, Common tableware and Handmade pottery. Our studies of the mineralogic composition of the sherds` body indicate that all ceramics were produced locally, using silicious clays in most cases and calcareous clays in a few ones. Micro-Raman and ground state diffuse reflectance absorption spectroscopy provided useful information regarding the materials used to produce the coloured ceramics: hematite and brookite for the red slip and decorated ceramics, jacobsite or carbon black for the black decoration or grey ceramics. For the yellow slip tableware a simple engobe rich in yellow clay was used. XRF spectroscopic studies provided the elemental composition of all samples, and biplots of the Potassium (K) versus Calcium (Ca) contents, normalized to the silicon content of each ceramic paste, clearly show that Pliocene and Miocene local clays sources were used to produce most ceramics. Only one sherd can be considered a Lisbon production.

In this work, we report the electric energy storage properties of (1-x)Bi0.5(Na0.8K0.2)0.5TiO3-xBi0.2Sr0.7TiO3 (BNKT-BST; x = 0.15-0.50) relaxor ferroelectric ceramics enhanced via a domain engineering method. A rhombohedral–tetragonal phase, the formation of highly dynamic PNRs, and a dense microstructure are confirmed from XRD, Raman vibrational spectra, and microscopic investigations. The relative dielectric permittivity (2664 at 1 kHz) and loss factor (0.058) were gradually improved with BST (x=0.45). The incorporation of BST into BNKT can disturb the long-range ferroelectric order, lowering the dielectric maximum temperature Tm and inducing the formation of highly dynamic polar nano-regions. In addition, the Tm shifts toward high temperature with frequency and a diffuse phase transition, indicating relaxor ferroelectric characteristics of BNKT-BST ceramics, which is confirmed by the modified Curie Weiss law (γ=1.83). The rhombohedral–tetragonal phase, fine grain size, and lowered Tm with relaxor properties synergistically contribute to a high recoverable energy density Wrec of 0.81 J/cm3 and a high energy efficiency η of 86.95% at 90 kV/cm for x = 0.45.

The civil construction industry is one of the sectors that most consume natural resources in the world and, consequently, one of that generate more waste. Thinking about constructive techniques that generate less impact on the environment is vital to ensure sustainable development. In this scenario, the Life Cycle Assessment (LCA) has been presented as an internationally recognized approach, that assesses the potential impact of products and services on human health and the environment, throughout its entire life cycle. Aimed to identify construction techniques and vertical closing systems that generate less impact and consumption of natural resources, the impacts generated by the life cycle of the three vertical closing systems most applied in construction sites in Brazil were compared: ceramic brick masonry system (CBr); concrete block masonry system (CBk); and structural blocks masonry system (SBk). The SBk proved to be the least impacting to the “Resource Scarcity”, “Damage to Human Health”, and “Damage to the diversity of Ecosystems” interesting areas. This performance is directly related to the use of cement CPIII type and also by the fact that the SBk consumes less concrete and mortar than the others. Already the "Water Consumption" area, the CBk was the least impacting due to the lower consumption of electricity during its life cycle. The reliability of the results was proven through a sensitivity analysis of the normalization and characterization factors, which consisted of comparing the results obtained by applying two different methodologies. It is believed that the LCA study carried out can assist in the decision-making process regarding the choice of the most sustainable construction method.

Nickel-based superalloys are attractive to many industrial sectors (automotive, military, energy, aerospace etc.). However, their physical properties make them difficult to machining using traditional tools. Therefore, the new materials for the machining of Ni-based alloys are required. Ceramic-based composites could act as a tool to replace the current materials. The incentives for this paper are to provide an overview of existing ceramic composites and draw some conclusions that will help in solving the problem of choosing materials for processing of Ni-based superalloys. Despite the diversity of ceramic composites in this work the focus was on the SiAlON ceramic.

Fouling represents a bottleneck problem for promoting the use of membranes in filtration and separation applications. It becomes even more persistent when it comes to the filtration of fluid emulsions. In this case, a gel-like layer that combines droplets, impurities, salts, and other materials form at the membrane's surface, blocking its pores. It is, therefore, a privilege to combat fouling by minimizing the accumulation of these droplets that work as seeds for other incoming droplets to cluster and coalesce with. In this work, we explore the use of the newly developed and novel periodic feed pressure technique (PFPT) in combating the fouling of ceramic membranes upon the filtration of oily water systems. The PFPT is based on alternating the applied transmembrane pressure (TMP) between the operating one and zero. A PFPT cycle is composed of a filtration half-cycle and a cleaning half-cycle. Permeation occurs when the TMP is set at its working value, while the cleaning occurs when it is zero. Three PFPT patterns were examined over two feeds of oily water systems with oil contents of 100 and 200ppm, respectively. The results show that the PFPT is very effective in minimizing the problem of fouling compared to a non-PFPT normal filtration. Furthermore, the overall drops in permeate flux during the cleaning half cycles are compensated by appreciable enhancement due to the significant elimination of fouling development such that the overall production of filtered water is even increased. Inspection of the internal surface of the membrane post rinsing at the end of the experiment proves that all PFPT cycles maintained the ceramic membranes as clean after a 2-hours operation. This can ensure a prolonged lifespan of the ceramic membrane use and a continuous greater permeate volume production. The advantage of the PFPT is that it can be implemented on existing units with minimal modification, ease of operation, and saving energy.

In the present work, the state of the art of the most common additive manufacturing (AM) technologies used for the manufacturing of complex shape structures of graphene-based ceramic nanocomposites, ceramic and graphene-based parts is explained. A brief overview of the AM processes for ceramic, which are grouped by the type of feedstock used in each technology, is presented. The main technical factors that affect the quality of the final product were reviewed. The AM processes used for 3D printing of graphene-based materials are described in more detail; moreover, some studies in a wide range of applications related to these AM techniques are cited. Furthermore, different feedstock formulations and their corresponding rheological behaviour were explained. Additionally, the most important works about the fabrication of composites using graphene-based ceramic pastes by Direct Ink Writing (DIW) are disclosed in detail and illustrated with representative examples. Various examples of the most relevant approaches for the manufacturing of graphene-based ceramic nanocomposites by DIW are provided.

Nanopowders are continuously under investigation as they open new perspectives in numerous fields. There are two main challenges to stimulate their development: sufficient low-cost high throughput synthesis methods leading to a production with well-defined and reproducible properties, and for ceramics, conservation of their nanostructure after sintering. In this context, this paper presents the synthesis of a pure nanosized powder of ZnO (dv₅₀ ~ 60 nm, easily redispersable) by using a continuous Segmented Flow Tubular Reactor (SFTR), which has previously shown its versatility and its robustness, ensuring a high powder quality and reproducibility over time. A higher scale of production can be achieved based on a “scale-out” concept by replicating the tubular reactors. The sinterability of ZnO nanopowders synthesized by the SFTR was studied, by natural sintering at 900 °C and 1100 °C, and Spark Plasma Sintering (SPS) at 900 °C. The performances of the synthesized nanopowder were compared to a commercial ZnO nanopowder of high quality. The samples obtained from the synthesized nanopowder could not be densified at low temperature by traditional sintering, whereas SPS led to a fully dense material after only 5 minutes at 900 °C, while limiting the grain growth and thus leading to a nanostructured material.

In this study, the hybrid biological ion exchange (BIEX) resin and gravity-driven membrane (GDM) process was employed for the treatment of coloured and turbid river water. The primary objective was to investigate the impact of both physical and chemical cleaning methods on ceramic and polymeric membranes in terms of stabilised flux, flux recovery after physical/chemical cleaning, and permeate quality. To address these objectives, two types of MF and UF membranes were utilised (M1 = polymeric MF, M2 = polymeric UF, M3 = ceramic UF, and M4 = lab-made ceramic MF).Throughout extended operation, the resin functioned initially in the primary ion exchange (IEX) region (NOM displacement with pre-charged chloride) and progressed to a secondary IEX stage (NOM displacement with bicarbonate and sulphate), while membrane flux remained stable. Subsequently, physical cleaning involved air/water backwash with two different flows and pressures, and chemical cleaning utilised NaOH at concentrations of 20 and 40 mM, as well as NaOCl at concentrations of 250 and 500 mg Cl2/L. These processes were carried out to assess flux recovery and identify fouling reversibility. The results indicated an endpoint of 1,728 bed volumes (BV) for the primary IEX region, while the secondary IEX continued up to 6,528 BV. At the end of the operation, DOC and UVA254 removal in the effluent of the BIEX columns were 68% and 81%, respectively, compared to influent water. This was followed by 30% and 57% DOC and UVA254 removal by M4 (ceramic MF). The stabilised flux remained approximately 3.8 – 5.2 LMH both before and after the cleaning process, suggesting that membrane materials do not play a pivotal role. The mean stabilised flux of polymeric membranes increased after cleaning, whereas that of ceramics decreased. Enhanced air–water backwash flow and pressure resulted in increased removal of hydraulic reversible fouling, which was identified as the dominant fouling type. Ceramic membranes exhibited higher removal of reversible hydraulic fouling than polymeric membranes. Chemical cleaning had a low impact on flux recovery; therefore, we recommend solely employing physical cleaning.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

To understand the enhanced protection mechanism of CoCrNiAlY-YSZ-LaMgAl11O19 dou-ble-layer ceramic coating with aluminum plating, a finite element simulation method was used to simulate the distribution of thermal stress in the coating in all directions. The results show that in the air exposure of the un-aluminized coating, high temperature causes a large radial thermal stress on the surface of the LaMgAl11O19 (LMA) layer, and it increases with the increase in temperature, which is the main reason for the initiation of axial cracks. After arc aluminum plating, the aluminum plating layer effectively inhibited the volume shrinkage of the coating through good adhesion to the coating and internal diffusion, the thermal stress of the coating was considerably reduced, and the CoCrNiAlY-YSZ-LMA coating had an effective enhancement and protection effect; however, there was still a certain amount of shear thermal stress inside the LMA layer, the top of the crack, and the bottom of the crack. This thermal stress caused the initi-ation of radial microcracks in the LMA layer, which also becomes a risk point for the failure of the aluminum coating.

In this work, effects of 20 transition element additives on the interfacial adhesion energy and electronic structure of Al (111)/6H-SiC (0001) interfaces have been studied by first principles method. For clean Al (111)/6H–SiC (0001) interfaces, both Si-terminated and C-terminated interfaces have covalent bond characteristics. The C-terminated interface has stronger binding energy, which is mainly due to the stronger covalent bond formed by the larger charge transfer between C and Al. The results show that the introduction of many transition elements, such as 3d transitional group Mn, Fe, Co, Ni, Cu, Zn and 4d transitional group Tc, Ru, Rh, Pd, Ag, can improve the interfacial adhesion energy of the Si-terminated Al (111)/6H-SiC (0001) interface. However, for the C-terminated Al (111)/6H-SiC (0001) interface, only the addition of Co element can improve the interfacial adhesion energy. Bader charge analysis shows that the increase of interfacial binding energy is mainly attributed to more charge transfer.

As the field of nanoscience is rapidly evolving, interest for novel, upgraded nanomaterials with combinatory features is also inevitably increasing. Hybrid composites, offer simple, budget-conscious and environmental-friendly solutions that can cater multiple needs at the same time and be applicable in many nanotechnology-related and interdisciplinary studies. The physicochemical idiocrasies of dendritic polymers have inspired their implementation as sorbents, active ingredient carriers and templates for complex composites. Ceramics are distinguished for their mechanical superiority and absorption potential that render them ideal substrates for separation and catalysis technologies. The integration of dendritic compounds to these inorganic hosts can be achieved through chemical attachment of the organic moiety onto functionalized surfaces, impregnation and absorption inside the pores, conventional sol-gel reactions or via biomimetic mediation of dendritic matrices, inducing the formation of usually spherical hybrid nanoparticles. Alternatively, dendritic polymers can propagate from ceramic scaffolds. All these variants are covered in detail. Optimization techniques as well as established and prospected applications are also presented.

The difficult current environmental situation, caused by construction industry residues containing ceramic materials could be improved by using these materials as recycled aggregates in mortars, with their processing causing a reduction in their use in landfill, contributing to recycling and also minimizing the consumption of virgin materials. Although some research is currently being carried out into recycled mortars, little is known about their stress-strain (σ-ε); therefore this work will provide the experimental results obtained from recycled mortars with recycled ceramic aggregates (with contents of 0, 10, 20, 30, 50 and 100%), such as: the density, the compression strength, as well as the σ-ε curves representative of their behavior. The values obtained from the analysis process of the results are those of: σ (elastic ranges and failure maximum), ε (elastic ranges and failure maximum), and Resilience and Toughness; in order to finally obtain, through numerical analysis, the equations to predict their behavior (related to their recycled content). At the end of the investigation it is established that mortars with recycled ceramic aggregate contents of up to 20% could be assimilated just like mortars with the usual aggregates, and the prediction equations produced could be used in cases of similar applications.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

Li-ion cell designs, component integrity and manufacturing processes all have critical influence on the safety of Li-ion batteries. Any internal defective features that induce a short circuit, can trigger a thermal runaway: a cascade of reactions, leading to a device fire. As consumer device manufacturers push aggressively for increased battery energy, instances of field failure are increasingly reported. Notably Samsung made a press release in 2017 following a total product recall of their Galaxy Note 7 mobile phone, confirming speculation that the events were attributable to the battery and its mode of manufacture. Recent incidences of battery swelling on the new iPhone 8 have been reported in the media, and the techniques and lessons reported herein may have future relevance. Here we look deeper into the key components of one of these cells and confirm evidence of cracking of electrode material in tightly folded areas, combined with a delamination of surface coating on the separator, which itself is an unusually thin monolayer. We report microstructural information about the electrodes, battery welding attributes and thermal mapping of the battery whilst operational. The findings point to the most likely combination of events and highlights the impact of design features, whilst providing structural considerations most likely to have led to the reported incidences relating to this phone.

Background &amp; Aim: Drug sustainability (DS) is a surrogate marker for treatment efficacy. We aimed to compare the DS of two main biologics used to treat moderate-to-severe ulcerative colitis (UC), infliximab (IFX) and vedolizumab (VDZ), in a real-world setting. Methods: We conducted a retrospective cohort study at a tertiary medical center in Israel. We included patients treated between Dec 1st, 2017, and May 1st, 2021, who were followed for up to 300 weeks. DS was defined as corticosteroid, surgical, and hospitalization-free treatment. Results: 217 patients with UC were included. VDZ had a significantly longer median DS of 265.6 weeks compared to IFX's 106.5 weeks (p=0.001) in treatment-naïve patients, even when adjusting for disease severity (HR 0.55 95 CI 0.3-0.98, p=0.042). In treatment-experienced patients, DS was comparable between IFX and VDZ (p=0.593). Conclusion: VDZ showed significantly longer DS in treatment-naïve patients with UC compared to IFX, also when adjusted for disease severity. There was no difference in DS between VDZ and IFX in treatment-experienced patients and patients switching from one drug to another. VDZ may be a suitable first-line treatment for biologic-naïve patients with moderate-to-severe UC.

Background: Cancer has been one of the most critical health problems during the past decades which require serious consideration, especially in developing countries. Methods: 80 parents of the children with different types of cancers were studied via both questionnaire and person-to-person interview after announcing their informed consent. Results: The highest delay in patients' initial referral was due to the following factors: lack of attention or ignoring the first symptoms, delay in referring to the physician, low economic status and even lack of family support for the patient. In addition, visiting several doctors after the initial diagnosis, uncertainty about the first proposed method, and high cost of treatment can be mentioned as the main causes of delays in the start of treatment. Conclusion: Education plays an important role in identifying the signs of cancer. In addition, proper relationship and cooperation between the health system and physicians as well as provision of adequate information to patients could lead to the long-term cooperation of these patients in continuing their treatment.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Current article presents the study of psychological wellbeing of adolescents (n=168, age 15-17) gifted in math, humanities and sports and educated in advanced programs for gifted children. Theoretical framework of this study is eudemonic concept of psychological wellbeing by C. Ryff. Psychological wellbeing is measured with Ryff wellbeing scales in Russian adaptation by L.V. Zhukovskaya and E.G. Troshikhina. The study is aimed at understanding differences in psychological wellbeing of gifted teenagers connected to gender and type of giftedness. The results suggest that general wellbeing score did not differ for adolescents with different types of giftedness or of different genders. Separate components of psychological wellbeing, such as purpose in life and self-acceptance, are influenced by activity connected to the talent. Gender differences are subjected to age-specific trends of personal development in adolescence. Type of giftedness might reinforce these trends.

With Internet of Things (IoT) gaining presence throughout different industries a lot of new technologies have been introduced to support this undertaking. Implications on one such technology, wireless systems allowed for the use of different communication methods to achieve the goal of transferring data reliably, with more cost efficiency and over longer distances. Anywhere from a single house with only a few IoT devices such as a smart light bulb or a smart thermostat connected to the network, all the way to a complex system that can control power grids throughout countries, IoT has been becoming a necessity in everyday lives. This paper presents an overview of the devices, systems and wireless technologies used in different IoT architectures (Healthcare, Vehicular Networks, Mining, Learning, Energy, Smart Cities, Behaviors and Decision Making), their upbringings and challenges to this date and some foreseen in the future.

Transition metal complexes have historically played a pivotal role in creating vibrant pigments utilized across artistic mediums such as ceramics, paintings, and glass mosaics. Despite their extensive historical use, our understanding of the mechanisms governing transition metal complex behavior has predominantly emerged in recent times, leaving numerous aspects of this process ripe for exploration. These complexes exhibit striking color variations under diverse conditions when employed in pigment formulations. This review utilizes a bottom-up scientific approach, spanning from microscopic to macroscopic scales, to unravel the molecular origins of the colors generated by transition metal complexes in pigments and ceramic glazes. Advanced spectroscopy techniques and computational chemistry play pivotal roles in this endeavor, highlighting the significance of understanding and utilizing analytical data effectively, with careful consideration of each technique's specific application. Furthermore, the review investigates the influence of processing conditions on color variations, providing valuable insights for artists and manufacturers aiming to enhance the precision and quality of their creations while mitigating environmental impact.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Traditional potential transformers have problems of large volume, difficulty in insulation, iron core saturation, ferroresonance overvoltage and poor transient response characteristics. The voltage sensor based on the principle of electric field coupling and differential input structure does not need to contact the measured object or ground, and can avoid the above problems. However, it requires a sufficiently high capacitance between the differential electrodes to obtain sufficient accuracy and a high voltage division ratio. The existing method of using mutual capacitance between the differential electrodes will cause many problems and fail to meet the practical needs. To solve the above problems, this paper innovatively uses multi-layer ceramic capacitor to replace the mutual capacitance and designs a new type of voltage sensor. In addition, by using single bypass small resistance grounding method to increase the input impedance of the differential signal processing circuit, error of the sensor is further reduced. The experimental results show that the sensor has excellent accuracy and great transient response characteristics. The ratio error under power frequency is within ±0.5% and the phase error is within 1. The ratio error in the range of 500 Hz∼30 kHz is within ±5% and the phase error is within 5. Moreover, it has the advantages of low cost, miniaturization, flexible shape and easy to adjust the voltage division ratio. These characteristics indicate that the sensor has good voltage measurement and sensor network potential.

The purpose of this study was to evaluate the bioactivity and cell response of a well-characterized Nurse´s A-phase (7CaO•P2O5•2SiO2) ceramic and his effect compared to a control (tissue culture polystyrene-TCPS) on the adhesion, viability, proliferation and osteogenic differentiation of ahMSCs in vitro. Cell proliferation (Alamar Blue Assay), Alizarin Red-S (AR-s) staining, alkaline phosphatase (ALP) activity, osteocalcin (OCN) and collagen I (Col I) were evaluated. Also, field emission scanning electron microscopy (FESEM) images were acquired in order to visualise the cells and the topography of the material. The proliferation of cells growing in a direct contact with the material was slower at early stages of the study because of the new environmental conditions. However, the entire surface was colonized after 28 days of culture in growth medium (GM). Osteoblastic differentiation markers were significantly enhanced in cells growing on Nurse´s A phase ceramic and cultured with osteogenic medium (OM), probably due to the role of silica to stimulate the differentiation of ahMSCs. Moreover, calcium nodules were formed under the influence of ceramic material. Therefore, it is predicted that Nurse´s A-phase ceramic would present high biocompatibility and osteoinductive properties being a good candidate to be used as a biomaterial for bone tissue engineering.

The numerous biological activities of phenothiazine and sulphonamide derivatives, especially their antibacterial qualities, have attracted so much interest. In this study, the synthesis and characterization of phenothiazine-3-sulphonamide derivatives and evaluation their antimicrobial activity against the following pathogenic microorganisms is reported. Two gram-positive bacteria; (Staphylococcus aureus, and Streptococcus pyogenes), two gram-negative bacteria; (Escherichia coli, and Salmonella typhi) as well as one fungus (Aspergillus fumigatus) were used while ciprofloxacin, gentamycin and ketoconazole served as standard drugs. The synthesis of the derivatives was achieved through a base catalyzed the reaction of 4-chloroaniline with 1-naphthylamine to form 1-(naphthalen-1-yl) benzene-1,4-diamine. This intermediate was then treated with sulphur and iodine to yield the phenothiazine derivative while subsequent treatment of the phenothiazine compound with sulphonyl chlorides gave the final products. The synthesized compounds were characterized via proton nuclear magnetic resonance (1HNMR), carbon-13 nuclear magnetic resonance (13C NMR) and Fourier-transform infrared (FTIR) spectroscopic techniques. The minimum inhibitory concentration (MIC) of each compound was then determined using the agar well diffusion method. To predict the binding energies and patterns of the synthesized compounds with target proteins of the above mentioned microorganisms, molecular docking simulations were run using Autodock Vina software (version 4.2). The spectra data of the compounds for FTIR, 1H NMR and 13C NMR (δ) spectral data were consistent with the assigned structures of the synthesized compounds. The binding energies (kcal/mol) for in silico antimicrobial studies were in the range -5.1 to -7.6 kcal/mol. The MIC values were in the range -3.5 to 1.0 mg/L. The results of the in vitro test revealed that the synthesized compounds exhibits promising antimicrobial activity, and showed excellent bactericidal and fungicidal activities. The results obtained showed that the synthesized compounds possess drug-like properties and are good starting materials for drug production.

Background: Redo mitral valve surgery is the standard of care for failed mitral bioprostheses or recurrence of mitral regurgitation after repair. Nonetheless, catheterbased valve-in-valve (ViV) or valve-in-ring (ViR)-procedures increasingly become viable alternatives in high risk subpopula-tions. Despite reported good initial results, only little is known about longer-term outcomes. The present series report long-term outcomes of transcatheter mitral ViV- and ViR-procedures. Methods: All consecutive patients (n=54) undergoing transcatheter mitral ViV- or ViR-procedures for failed bioprostheses or recurring regurgitation after mitral repair were retrospectively en-rolled in the time period between 2011 and 2021. The mean age was 76.5 ± 6.5 years, and 30 (55.6%) of the patients were male. The procedures were done using a commercially available balloon-expandable transcatheter heart valve. Clinical and echocardiographic follow-up data were obtained out of the hospital’s database and analyzed. Follow-up reached up to 9.9 years with a total of 164.3 patient-years. Results: A total 25 patients received a ViV- and 29 patients a ViR-procedure. Both groups were at high surgical risk with an STS-PROM of 5.9 ± 3.7 % in ViV- and 8.7 ± 9.0% in ViR-patients, respectively (p<0.01). The procedures itself were mainly unevent-ful with no intraoperative deaths and a low conversion rate (n=2/54; 3.7%). VARC-2 procedural success was low (ViV 20.0% and ViR 10.3%; p=0.45), which was either driven by high rates of transvalvular pressure gradients “>5mmHg” (ViV 92.0% and ViR 27.6%; p<0.01) or residual regurgitation “>trace” (ViV 28.0% and ViR 82.7%; p<0.01). ICU-stay was prolonged in both groups (ViV 3.8 ± 6.8 days and ViR 4.3 ± 6.3 days; p=0.96) with acceptable hospital stay (ViV 9.9 ± 5.9 days and ViR 13.5 ± 8.0 days; p=0.13). Despite 30-days mortality was acceptable (ViV 4.0% and ViR 6.9%; p=1.00), the mean posthospital survival time was disappointingly low (ViV 3.9 ± 2.6 years and ViR 2.3 ± 2.7 years; p<0.01). Overall survival I the entire group was 33.3%.Cardiac reasons for death were frequent in both groups (ViV 38.5% and ViR 52.2%). Cox-regression analysis identified ViR-procedures as a predictor of mortality (HR 2.36, CI 1.19 - 4.67, p=0.01). Conclusions: Despite acceptable immediate outcomes in this high-risk subpopulation, long-terms results are discouraging. Transvalvular pressure gradients as well as residual regurgitations remained drawbacks in this real-world population. The indication for catheterbased mitral ViV- or ViR-procedures thoughtfully must be made in consideration of conventional redo-surgery or conservative treatment.

In an effort to discover an effective and selective antitumour agent, synthesis and anti-cancer potential of 4-(pyridin-4-yl)-6-(thiophen-2-yl)pyrimidin-2(1H)-one (SK-25), which has been reported earlier by us with significant cytotoxicity towards MiaPaCa-2 malignant cells, with an IC₅₀ value of 1.95 μM and was found to instigate apoptosis. In the present study, the antitumour efficacy of SK-25 was investigated on Ehrlich ascites tumour (solid), Sarcoma 180 (solid) tumour and Ehrlich ascites carcinoma. The compound was found to inhibit tumour development by 94.71% in Ehrlich ascites carcinoma (EAC), 59.06% in Ehrlich tumour (ET, solid) and 45.68% in Sarcoma-180 (solid) at 30 mg/kg dose. Additionally, SK-25 was established to be non-toxic at a maximum tolerated dose of 1000 mg/kg in acute oral toxicity in Swiss-albino mice. Computer-based predictions also show that the compounds could have an interesting DMPK profile. The current study provides insight for further investigation of the antitumour potential of the molecule.

In this paper, we discuss major issues of mathematics teaching and learning in Nepal. The issues coming from theories such as social and radical constructivism suggest that teachers are not trained to use such approach in teaching mathematics, and there is a lack of teaching aids and materials and technological tools. The issues related to social aspects are gender issues, language issues, social justice issues, and issues related to the achievement gap. The cultural issues are related to the diversity of language and ethnicity. The issues related to political aspects are equity and access, economic status, pedagogical choice, and professional organizations and unions. The issues related to technology include the technological skills, use of technology, and affordance. Finally, we suggest that all the stakeholders should pay attention to resolving these issues by improving the curriculum, training teachers, resourcing the classroom with locally made and new technological tools.

Physics behind collimated highly directional nature of lasers, and factors that keep the seven coloured waves that form white light together during their journey from Sun to Earth, in the face of the natural disruptive forces, is not fully understood. Energy levels were measured, in terms of alterations in induced current and voltage, in beams from a red laser, white LED light and the Sunlight before and during their disruption by diffusers (frosted glass for the lasers) and diffractors (diffraction grating for the white light) using a photovoltaic solar cell panel attached to a digital multimeter. Results show that disruption of the beams results in release of extra energy named as ‘Latent Light Binding’ Energy’. It is hypothesized that the ‘binding’ energy keeps laser waves firmly bound together both end-on and side-on enabling laser beams to travel long distances in collimated manner. Likewise, the 7 coloured waves that constitute white light are kept together, probably side-on, in their journey from the Sun to the Earth. The observation that diffraction of sunbeam is associated with increased power generation provides a new lead to improve harnessing of solar energy, where, currently, the focus is mainly on improving efficiency of photovoltaic cell.

Piceatannol is a naturally occurring polyphenolic compound that is widely found in grapes, blueberries, mushrooms, passion fruit and other edible fruits and vegetables. It has a variety of biological activities and pharmacological effects, including anti-inflammatory, antioxidation, antiaging, antiviral, antitumor, anticancer, antiatherosclerosis, antiparasitic, immunoregulatory, and cardiovascular protection effects. The aim of this study was to investigate the antiherpesvirus effects of piceatannol. Pseudorabies virus (PRV) belongs to the family Herpesviridae. PRV has a wide host range and can cause cytopathic effects (CPEs) in PK-15 cells. Therefore, PRV was used as a model to study the antiherpesvirus effect of piceatannol. In this study, we evaluated the antiviral activity of piceatannol against PRV in vitro and in vivo. The results showed that piceatannol could reatrain PRV multiplication in PK-15 cells in a dose-dependent manner. The 50% inhibitory concentration (IC50) was 0.0307 mg/mL, the IC50 was 0.0307 mg/mL, and the selectivity index (SI, CC50/IC50) was 3.68. The addition of piceatannol at different stages of PRV infection inhibited the viral adsorption and intracellular replication phases of PRV. Piceatannol significantly reduced the expression levels of the IE180, EP0, UL29, UL44, US6 and UL27 genes of PRV within 48 h, significantly reduced the expression levels of the PRV gB and gD proteins, and reduced PRV-induced apoptosis. Molecular docking showed that piceatannol had good binding activity with the PRV gB and gD proteins. The results of animal experiments in vitro indicated that piceatannol could delay the onset of disease, improve the survival rate of the mice (14.3%), reduce the viral load in the brain and kidney of the mice, alleviate the pathological changes in the mouse tissues and organs, and increase the levels of TNF-α, IEN-γ and IL-4 in the serum of the mice. These data indicate that piceatannol has good anti-PRV activity in vitro and in vivo, indicating that it could be a novel antiherpesvirus infection agent in the future.

Diabetes mellitus is a global health issue that necessitates the development of novel therapeutic approaches. Today numerous experimental methods have been used and set up to evaluate novel drugs with antidiabetic effects. In addition, several research studies have been done to induce diabetes under in vitro and in vivo conditions, but only a small number of these efforts are currently in a usable stage. This review aims to provide useful guidance for researchers who seek to evaluate the antidiabetic potential of drugs, agents, or new medications using the standard methods published by authorities and academics worldwide organizations and research centers. In this review, we collected 132 relevant articles from prominent databases such as PubMed, ScienceDirect, Scopus and others to summarize in vitro and in vivo experimental validation of antidiabetic treatment from 1943 to present.

Leishmaniasis is a vector-borne parasitic infection caused by the bite of female Phlebotomine sandflies. World Health Organization (WHO) estimates 100,000 cases to be reported annually on a global scale, moreover, 13 million people were infected between 2010 and 2015 worldwide. Treatment of leishmaniasis by conventional synthetic compounds is met by challenges pertaining to adverse effects which call for the discovery of newer anti-leishmanial molecules. This study was performed to evaluate the effect and modes of action of a sesquiterpene alcoholic molecule Farnesol on Leishmania major, the causative agent of Zoonotic Cutaneous leishmaniasis. The cytotoxic effect of Farnesol against L. major promastigotes, amastigotes and macrophages was assessed by MTT test and counting. The IC50 on promastigotes by Farnesol on L. major was evaluated by flow cytometry. In the findings, Promastigotes were reduced at 167 µM/mL & the mean numbers of L. major amastigotes in macrophages were significantly decreased in exposure to Farnesol at 172 µM/ml. In addition, Farnesol demonstrated no cytotoxicity on macrophages as the IC50 value was 945 µM/ml; it induced significant apoptosis dose-dependent on L. major promastigotes. In silico protein-ligand binding analyses indicated the effect of Farnesol in perturbation of the ergosterol synthesis pathway of Leishmania with attributes suggesting inhibition of Lanosterol-α-demethylase, the terminal enzyme of ergosterol synthesis machinery. Findings from flow cytometry reveal the role of farnesol in apoptosis-induced killing in promastigotes. Farnesol was effective at very lower concentrations when compared to Paromomycin. Further studies are crucial to evaluate the therapeutic potentials of Farnesol alone and in combination with other conventional drugs using clinical settings.

In this study, multi-layer ceramic capacitors (MLCCs) detached from lighting sector's waste electrical-electronic equipment (WEEE) are characterised for the presence of rare earth elements (REEs) and precious metals (PMs). Their digestion was carried out with HNO3 & aqua regia on a heating plate and characterised with the use of inductively coupled plasma optical emission spectroscopy (ICP-OES) & scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX). The contents of REEs and PMs are 0.84 wt% and 0.60 wt%, respectively, and create an economic stored value in MLCCs that is essentially defined by PMs of 98.67% and by Pd 78.37%. The content of the main elements is: Nd 0.366 wt%, Y 0.220 wt%, Dy 0.131 wt%, Ag 0.467 wt%, and Pd 0.105 wt%. The results confirm the need of selective removal and separate recycling process of MLCCs from WEEE drivers.

In this paper, we investigate the structural, microstructural, dielectric, and energy storage properties of Nd and Mn co-doped Ba0.7Sr0.3TiO3 [(Ba0.7Sr0.3)1-xNdxTi1-yMnyO3 (BSNTM) ceramics (x = 0, 0.005, and y = 0, 0.0025, 0.005, and 0.01)] via a defect dipole engineering method. The complex defect dipoles (MnTi"-VO∙∙)∙ and (MnTi"-VO∙∙) between acceptor ions and oxygen vacancies capture electrons, enhancing the breakdown electric field and energy storage performances. XRD, Raman spectroscopy, and microscopic investigations of BSNTM ceramics revealed the formation of a tetragonal phase, increased oxygen vacancies, and reduced grain size with Mn dopant, respectively. The BSNTM ceramics with x=0.005 and y=0 exhibit a high dielectric constant of 2058 and a dielectric loss of 0.026 at 1 kHz. These values gradually decreased to 1876 and 0.019 for x=0.005 and y=0.01 due to the Mn2+ ions at Ti4+-site, which facilitates the formation of oxygen vacancies, and prevents the decrease of Ti4+. In addition, the defect dipoles act as a driving force for depolarization to tailor the domain formation energy and domain wall energy, which provides a high difference between the maximum polarization of Pmax and remnant polarization of Pr (ΔP=10.39 µC/cm2). Moreover, the complex defect dipoles with optimum oxygen vacancies in BSNTM ceramics can provide not only a high ΔP but also reduce grain size, which together improve the breakdown strength from 60.4 to 110.6 kV/cm, giving rise to a high energy storage density of 0.41 J/cm3 and high efficiency of 84.6% for x=0.005 and y=0.01. These findings demonstrate that defect dipoles engineering is an effective method to enhance the energy storage performance of dielectrics for capacitor applications.

This article explores the relationship between convex functions defined on integers ($\mathbb{Z}$) and their extension to real numbers ($\mathbb{R}$). We introduce key definitions and investigate the hypothesis that there exists a unique convex curve within this family of functions, leading to a proof by contradiction. Our findings highlight the preservation of convexity as functions transition from integers to real numbers.

Among the alternatives pointed out as able to make livestock a more efficient activity and reduce its environmental impact, the use of feeds with high digestibility and the use of non-conventional fodder species can be highlighted. Tithonia diversifolia (Hemsl.) A. Gray (TD) has already gained attention as a feed for ruminants. Nonetheless, there has been little discussion about the impacts of this plant on the rumen dynamics that lead to better animal performance. The aim of this study was to assess how increasing levels of TD could affect ruminal microbial biomass synthesis, degradability, and in vitro gas production (IVGP) of diets. Four diets were evaluated: a control diet (TD0: 400 g kg-1 soybean meal and corn grain, and 600 g kg-1 Tifton 85 hay (Cynodon spp)) and three increasing levels of TD (TD9: 90, TD27: 270, and TD45: 450 g kg-1 – dry matter basis) as a replacement for dietary roughage. A 96-hour IVGP assay was carried out and five incubation times (2, 4, 10, 24, and 96 hours) were used for degradability determination. Gas produced, methane (CH4), degradability of organic matter (IVDOM), short-chained fatty acid (SCFA) production, partitioning factor (PF), and microbial biomass (MB) were evaluated among treatments. There was no significant effect (P&gt;0.05) between TD inclusion and IVGP at most incubation times; only at 6 hours of incubation did gas production increase linearly with TD inclusion (R2=0.19; P&lt;0.05). TD inclusion had no effects on CH4. IVDOM increased linearly with TD inclusion at 6 and 10 hours, with TD45 being more degradable than the control diet at 6 hours only. There was a positive linear relationship (R2=0.20; P&lt;0.05) between TD inclusion and PF. TD45 had significantly higher PF values than the control. MB also increased linearly (R2=0.30; P&lt;0.05) with TD inclusion, and all diets with TD had significantly more MB than the control diet. The inclusion of TD at the levels used in this work was revealed to have a positive impact on microbial protein synthesis, which could be related to the higher microbial efficiency of increased substrate quality.

Oxalate, a compound produced by many edible plants and as a terminal metabolite in the liver of mammals, is a toxin that has a detrimental role to human health. Humans and other mam-mals do produce the enzymatic machinery to degrade oxalate. However, numerous oxa-late-degrading bacteria reside in the mammalian gut and thus provide an important function for hosts. The current review focuses on the environmental factors that influence the efficacy of pro-biotic oxalate-degrading bacteria, relative to oxalate metabolism. We describe the mechanism of oxalate catabolism and its consumption by obligate and facultative anaerobic oxalate-degrading bacteria, in both in vitro and in vivo environments. We also explore the environmental variables that impact oxalate degradation. Studies on single species degrade oxalate have not shown a strong impact on oxalate metabolism especially in high oxalate conditions such as consumption of foods high in oxalate (such as coffee and chocolate for humans or halogeton in animal feed). Considering effective variables which enhance oxalate degradation could be used in application of effective probiotic as a therapeutic tool in individuals with hyperoxaluria. This study indicates probiotics can be considered a good source of naturally occurring oxalate degrading agent in human colon

The World Anti-Doping Agency has prohibited gene doping in the context of progress in gene therapy. There is a risk that the artificial regulation of genes using plasmids could be applied for gene doping. However, no gold standard method to detect this has been established. Here, we aimed to develop a method to detect multiple transgene fragments as proof of gene doping. First, gene delivery model mice as a mimic of gene doping were created by injecting firefly luciferase plasmid with polyethylenimine (PEI) into the abdominal cavity. The results confirmed successful establishment of the model, with sufficient luminescence upon in vivo imaging. Next, multiple transgene fragments in the model were detected in plasma cell-free (cf)DNA, blood-cell-fraction DNA, and stool DNA using the TaqMan-qPCR assay, with the highest levels in plasma cfDNA. Using just a single drop of whole blood from the model, we also attempted long-term detection. The results showed that multiple transgene fragments were detected until 11 days. These findings indicate that the combination of plasma cfDNA or just one drop of whole blood with TaqMan-qPCR assay is feasible to detect plasmid-PEI-based gene doping. Our findings could accelerate the development of methods for detecting gene doping in humans.

To determine the fracture rate of ceramic crowns and causes of ceramic crown failure, this study used keywords—namely “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown”—to search for articles published in English from 2005 to 2023 in the PubMed electronic database. Rather than using the Boolean logic algorithm between MESH terms and keywords, we accurately calculated the numbers of final clinically tracked cases with crown fractures from the contents of articles. The titles and abstracts of many related articles focused on implant or abutment fracture, while crown fracture was investigated and mentioned only in the main texts of the articles. Our studies included those crowns as well as having more complete data collection. Our search yielded 228, 93, 404, and 358 articles for the keywords “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown,” respectively. We used the Newcastle–Ottawa Scale (NOS) to assess article quality, and our inclusion criteria were randomized controlled trials (RCT) and cohort study articles involving more than 3 years of follow-up and more than 20 cases. After reviewing, 16 high-quality articles were selected for analysis. The 4.4% crown fracture rate recommended on the basis of most clinical results was achieved in only 6 of the 16 articles. In these 6 articles, the researchers concluded the following reasons that may cause the crown fractures: the thickness of the veneer ceramic material; the connector dimensions; pontic span of the fixed prosthesis; the type of cement; the treatment of the ceramic surface before luting. Other articles inferred that the computer-aided design libraries that were insufficient for the creation of appropriate anatomically supported frameworks for prostheses with ceramic veneers; the thermal expansion coefficient and fracture toughness of the framework material did not match those of the veneer ceramic, resulting in an insufficient area supporting the ceramic veneer then leads to premature crown failure after a long period chewing. The future prospective for material developing could focus on solving those problems and have better clinical results.

Cable-supported façades represent a novel approach in the design and technology of double skin façades (DSF). This type of systems not only offer flexibility in terms of exterior finishes, but also regulates the access of solar radiation, thereby transforming the appearance of the building in response to varying daylight conditions. However, the structural performance of these façades under wind, impact and seismic loads remains an active area of research. The study is a groundbreaking work that experimentally evaluates the wind and seismic behaviour of these type of façades. The methodology used for the evaluation of flexible masonry facades includes laboratory tests analysing the individual capacity of the connections and materials of the system under standardized and non-standardized procedures. A full-scale experimental sub-assembly specimen of a representative module of the façade is also subjected to uniformly distributed pressures of wind load tests as well as hard body and soft body impact tests. The setup considered the border conditions, tension loads, and actual materials. Furthermore, the earthquake assessment includes tests of full-scale specimens subjected to these demands. Research findings allowed the refinement and redesign of the system's components granting the validation of the DSF used as a case study.

Bioactive fractions were isolated from the leaves extract of Kalanchoe pinnata and subjected to scrutiny for their prospective anti-obesity properties. An array of in vitro phytochemical, antioxidant, and enzyme inhibition assays were executed, which dis-cerned fractions F1 and F2 as the most effective fractions. These fractions were sub-sequently studied through in vivo experiments, affirming that F2 as the most potent fraction. Further characterization of F2 was conducted via HPTLC MS-MSn tech-niques. The outcomes demonstrated that F2 produced a notable anti-obesity effect in obese mice, reducing their body weight and lipid metrics, and leading to advanta-geous changes in their organs. An analytical examination of F2 revealed the existence of four principal compounds, which were subsequently subjected to in silco molecular docking and dynamic analysis, confirming their aptitude for binding to selected pro-teins. These findings imply that the utilization of Kalanchoe pinnata leaves could pro-vide a promising therapeutic strategy for the treatment of obesity.

Analysing the human body by direct observation can lead to misinterpretation of underlying trends, whereas in vitro organ models facilitate their understanding. Likewise, in vitro organ models serve as valuable tools for assessing the toxicity of compounds. However, none of the existing models had the features we considered critical for toxicity assessment, so we developed an in vitro liver model for toxicity assessment. We used four different types of primary liver cells: Hepatic sinusoidal endothelial cells, hepatic stellate cells, Kupffer cells and hepatocytes. We cultured them in different combinations of composition and volume of cell medium, hepatocyte proportion of total cells, and addition of extracellular matrix. We added rifampicin, ibuprofen and 5-fluorouracil to this model and observed the microanatomy and physiology changes for a week with preclinical and clinical instruments. Among the different model configurations, we selected the feature combination of the in vitro model that had similar biomarker values to those measured by the clinical instruments used in clinical diagnostics. When we exposed the selected model configuration to rifampicin, ibuprofen and 5-fluorouracil, the viability of Kupffer cells and liver sinusoidal endothelial cells was significantly lower than in the untreated samples. In contrast, we observed negligible viability of hepatocytes compared to the untreated samples. We have built an in vitro liver model that resembles the liver microenvironment and we have analysed it with clinical instrumentation to facilitate the data translation. In this sense, we have established that Kupffer and LSEC cells are suitable candidates for the search for clinical diagnostic markers of liver function.

Knowledge about ecological conditions and processes in centers of endemism (CoEs) is still limited with respect to various systematic groups of organisms, ecosystem types, ecological conditions and ecosystem functions. Endemics and CoEs play a prominent role in nature conservation monitoring and management, and in the organization of zoos, aquaria and botanical gardens. We review the meaning of different groups of organisms and indicators for the characterization of endemic-rich regions, the importance of heterogeneity in space, continuity in time, isolation and ex-situ management for the survival of endemic and threatened species. Currently, conversion of land cover and land use change are the most important causes of biodiversity decline and extinction risk of endemic and endangered species concentrated in CoEs. These are followed by climate change, including severe weather, and then natural processes such as volcanism, landslides or tsunamis. For conservation purposes the management of zoos, aquaria, botanical gardens, of regional land use, and social aspects of the diversity of endemics and CoEs have to be taken into account as well. We need better answers to questions about the relationship between ecoregions, CoEs and regional awareness of biodiversity, which is linked with human culture including the management of zoos, aquaria and botanical gardens, aesthetics, wellbeing, health and trade.

Introduction: The combination of Virtual Screening (VS) techniques with in vivo screening in the zebrafish model is currently being used in tandem for drug development in a faster and more efficient way. Areas covered: We review the different virtual screening techniques, the use of zebrafish as a vertebrate model for drug discovery and the synergy that exists between them. Expert opinion: We highlight the advantages of combining virtual and zebrafish larvae screening for drug discovery. On the one hand, VS is a faster and cheaper tool for searching active compounds and possible candidates for therapy than in vivo screening when processing large compound libraries. On the other hand, zebrafish larvae form a vertebrate model which allows in vivo screening of large amounts of the compounds. Importantly physiology and chemical response are mostly conserved between zebrafish and mammals. The availability of the transgenic and mutant zebrafish lines allows an analysis of a specific phenotype upon treatment along with toxicity, off-target effect, side effects, and dosage. Advantages of VS, in vivo whole animal approach screening, and the screening combinations are also reviewed.

Human eye is a specialized organ with complex anatomy and physiology, because it is characterized by different cell types with specific physiological functions. Given the complexity of the eye, ocular tissues are finely organized and orchestrated. In the last few years many in vitro models have been developed, in order to meet the 3Rs principle (Replacement, Reduction and Refinement) for eye toxicity testing. This procedure is highly necessary to ensure that the risks associated with ophthalmic products meet appropriate safety criteria. In vitro preclinical testing is now a well-established practice of significant importance for evaluating the efficacy and safety of cosmetic, pharmaceutical, and nutraceutical products. Along with in vitro testing, also computational procedures, herein described, for evaluating the pharmacological profile of potential ocular drug candidates including their toxicity, are in rapid expansion. In this review the ocular cell types and functionality are described providing an overview about the scientific challenge for the development of three-dimensional in vitro models.

The study aims to elaborate a neural model and algorithm for optimising hardness and porosity of coatings and thus ensure that they have superior cavitation erosion resistance. Al2O3-13wt.%TiO2 ceramic coatings were deposited onto 316L stainless steel by atmospheric plasma spray (ASP). The coatings were prepared with different values of two spray process parameters: the stand-off distance and torch velocity. Microstructure, porosity and microhardness of the coatings were examined. Cavitation erosion tests were conducted in compliance with the ASTM G32 standard. Artificial neural networks (ANN) were employed to elaborate the model, and the multi-objectives genetic algorithm (MOGA) was used to optimise both properties and cavitation erosion resistance of the coatings. Results were analysed with Matlab software by Neural Network Toolbox and Global Optimization Toolbox. The fusion of artificial intelligence methods (ANN+MOGA) is essential for future selection of thermal spray process parameters, especially for the design of ceramic coatings with specified functional properties. Selection of these parameters is a multicriteria decision problem. The proposed method made it possible to find a Pareto front, i.e. trade-offs between several conflicting objectives – maximising the hardness and cavitation erosion resistance of Al2O3-13%TiO2 coatings and, at the same time, minimizing their porosity.

In our study we investigated the additive manufacturing (AM) of ceramic-based Functionally Graded Materials (FGM) by the direct AM technology Thermoplastic 3D-Printing (T3DP). Zirconia components with a varying microstructure were additively manufactured by using thermoplastic suspensions with different contents of pore forming agents (PFA) and were co-sintered defect-free. Different materials were investigated concerning their suitability as PFA for the T3DP process. Different zirconia-based suspensions were prepared and used for AM of single- and multi-material test components. All samples were sintered defect-free and in the end we could realize a brick wall-like component consisting of dense (<1% porosity) and porous (approx. 5% porosity) zirconia areas to combine different properties in one component. The T3DP opens the door to AM of further ceramic-based 4D-components like multi-color or multi-material, especially multi-functional components.

This comprehensive study delves into the implementation and effectiveness of the flipped classroom model in engineering EMI (English as a Medium of Instruction) courses in Taiwan. Situated within the strategic framework of Taiwan's Bilingual Nation 2023 policy, this research aims to enhance the global competitiveness of Taiwan's semiconducting manufacturing engineering sector. The study’s primary focus is on understanding the perceptions and learning outcomes of EFL (English as a Foreign Language) students in engineering courses. Through a methodical approach using descriptive statistics and chi-square tests, the study analyzes data from 33 junior engineering students specializing in mechanical and mechatronic fields. The findings highlight a significant positive influence of the flipped classroom model on various aspects of student learning, including increased engagement, heightened creativity, and enhanced problem-solving skills. Additionally, the study emphasizes the critical role of timely L1 support in facilitating effective learning in EMI settings. These outcomes not only demonstrate the flipped classroom's viability as a sustainable educational approach but also provide crucial insights for educators and policymakers. By aligning cutting-edge teaching methods with the evolving needs of engineering education, this study contributes to the discourse on educational innovation. It ultimately guides the development of future engineering programs that cater to diverse student needs and fosters the cultivation of skilled engineering professionals.

This study was to designed to develop sorafenib-loaded polymeric nanoparticles, surface-modified with pluronic F-127 for the effective treatment of hepatocellular (HCC) and renal cell carcinomas (RCC). Poly lactic coglycolic acid (PLGA) was used to encapsulate different concentrations of sorafenib by a simple modified solvent evaporation method applying pluronic F-127 as a surfactant and coating agent. The preformulation and characterization studies were conducted to evaluate the incompatibilities among sorafenib, PLGA and pluronic F-127, and physicochemical properties of the formulations, respectively. The sizes of the coated and plain PLGA nanoparticles were ~140 ± 14.7 nm and ~ 120 ± 10.1 nm, respectively. It has been confirmed from the in vitro release studies that PLGA sustained the release of sorafenib, avoiding the initial burst release, while the in vivo studies demonstared that surface-modified nanoparticles have greater affinity in the target aorgans than plain PLGA nanoparticles and free drug keeping the dose constant (20 mg/kg body weight). The delivery of sorafenib-loaded polymeric PLGA nanoparticles into the target tissues and their pharmacokinetic parameters have been improved significantly compared to the reported formulations.

The pinning force density FpJc,B=Jc×B (where Jc is the critical current density and B is the applied magnetic field) is one of the main parameters that characterize the resilience of a superconductor to carry a dissipative-free transport current in an applied magnetic field. Kramer (1973 J. Appl. Phys. 44 1360), and Dew-Hughes (1974 Phil. Mag. 30 293) proposed a widely used scaling law for the pinning force density amplitude: FpB=Fp,max×p+qp+qppqq×BBc2p×1-BBc2q, where Fp,max, Bc2, p, and q are free-fitting parameters. Since the late 1970-s till now, several research groups have reported experimental data on the dependence of Fp,max on the average grain size, d, in Nb3Sn-based conductors. Godeke (2006 Supercond. Sci. Techn. 19 R68) proposed that the dependence obeys the law Fp,maxd=A×ln1d+B. However, this scaling law has several problems, for instance, the logarithm is taken from a non-dimensionless variable, and Fp,maxd&lt;0 for large grain sizes, and Fp,maxd→∞ for d→0. Here, we reanalysed the full inventory of publicly available Fp,maxd data for Nb3Sn conductors and found that the dependence can be described by Fp,maxd=Fp,max0×exp-dδ law, where the characteristic length, δ, varies within a remarkably narrow range, that is, δ=175±13 nm, for samples fabricated by different technologies. The interpretation of the result is based on the idea that the in-field supercurrent flows within a thin surface layer (thickness of δ) near the grain boundary surfaces (similar to London’s law, where the self-field supercurrent flows within a thin surface layer with a thickness of the London penetration depth, λ, and the surface is a superconductor-vacuum surface). An alternative interpretation is that δ represents the characteristic length of the exponential decay flux pinning potential from the dominant defects in Nb3Sn superconductors, which are grain boundaries.

The Oxford English Dictionary includes 17 definitions for the word “model” as a noun and other 11 as a verb. Therefore, context is necessary to understand the meaning of the word model. For in-stance, “model railways” refer to replicas of railways and trains at a smaller scale and a “model student” refers to an exemplar individual. In some cases, a specific context, like cancer research, may not be sufficient to provide one specific meaning of a model. Even if the context is narrowed, specifically to the research related to the tumour microenvironment, a “model” can be understood in a wide variety of ways, from an animal model, to a mathematical expression. This paper presents a review of the different “models” of the tumour microenvironment grouped by the different def-initions of the word into four categories: model organisms, in vitro models, mathematical models, and computational models. Then, the frequency of different meanings of the word “model” related to the tumour microenvironment is measured from the number of entries in the MEDLINE database of the United States National Library of Medicine at the National Institutes of Health. The frequency of the main components of the microenvironment and the organ-related cancers modelled are also assessed quantitatively with specific keywords. Whilst animal models, in particular xenografts and mouse models are the most common used “models”, the number of entries have been slowly de-creasing. Mathematical models, prognostic and risk models follow in frequency and these have been growing in use.

In this review we look at the developments in the field of artificial intelligence (A.I) and their current impact as well as future implications in the field of cardiology, we as physicians and cardiologists have tried to put our perspective on the rapidly evolving field, In light of the fact that many of the healthcare workers and professionals across the world still find the concept of A.I quite complicated, elusive and somewhat paradoxical, we have tried to simplify the concept of artificial intelligence and make it easy for everyone to understand from all walks of life. The Databases utilized for our review are PubMed, PubMed Central, Google Scholar. The Keywords used for our Data Search are “Artificial Intelligence”, “A.I Cardiology”, “A.I in Cardiovascular Medicine”, “Machine Learning in Cardiology”. We screened all relevant since inception till March 25th and included 44 relevant articles after careful consideration into our paper. We have discussed the implementation of and scope of artificial intelligence across a broad spectrum of applications including cardiovascular imaging and diagnostics like electrocardiograms, echocardiograms, cardiac CT/MRIs to novel cardiac monitoring devices, CRISPR gene editing in cardiology and implementation of artificial intelligence in the field of Cardiovascular Bioprinting. This is the initial review in a series of reviews regarding A.I in Cardiology.

In this research paper, we address the critical role of data security in the rapidly evolving FinTech sector. We explore the challenges and strategies for establishing robust data security systems, emphasizing the consequences of data breaches and common vulnerabilities. The paper highlights the efficacy of technologies like encryption, blockchain, and cloud security, supported by real-world case studies from leading FinTech companies. Additionally, we examine regulatory frameworks and standards essential for maintaining data security. Concluding with the proposal of an integrated security system model, the paper underscores the synergy between technological innovation, regulatory compliance, and proactive risk management in the FinTech industry

While providing safe water for the rural poor is considered a basic human right, there are numerous issues associated with existing technologies with shortcomings. Performance issues have continued to fail to meet the needs of impoverished families due to issues including high cost, difficulties with performance, and continuing needs for maintenance. These issues have severely interfered the safe water accessibility. Key aspects of the Guelph Water Filter (GWF) system can avoid/minimize many of these issues. The GWF as described herein enables delivery of low cost, long-term performance at 3Log removal of E.coli and can deliver 1 to 3 L of treated water per hour. The GWF is simple to operate, has an ability to provide sufficient water for a family, maintains longevity of performance, is easy to maintain and has protection against breakage during the cleaning process, is repairable at village level, and operates using a sizable reservoir of water to supply raw water, meaning the technology does not need to be refilled frequently. Hence, the capability of the novel GWF technology is shown to bypass many of the troublesome features of alternative low-tech water treatment technologies. The potential for the GWF to function for 2 days continuously avoids the need for young girls to fetch raw water frequently during a day, thereby enabling them to attend school. Hence, the GWF enhances the potential to result in ‘safe water and full schools’, providing the opportunity for girls to receive education and capture socio-economic benefits for the community.

The process of anaerobic digestion used for methane production can be enhanced by incorporating stimulating materials. The effects of these materials are dependent on various factors including the processed substrate, process conditions, and the type and amount of the stimulating material used. As part of the study, three different stimulating materials - iron powder, lime, and milled porous ceramic - were added to the 30-day anaerobic digestion of the brewer's spent grain to improve its performance. Different doses ranging from 0.2 to 2.3 gTS×L-1 were tested, and methane production kinetics were determined using the first-order model. The results showed that the methane yield ranged from 281.4±8.0 to 326.1±9.3 ml×gVS-1, while substrate biodegradation ranged from 56.0±1.6 to 68.1±0.7%. The addition of lime reduced methane yield at almost all doses by -6.7% to -3.3%, while the addition of iron powder increased methane yield from 0.8% to 9.8%. The addition of ceramic powder resulted in a methane yield change ranging from -2.6% to 4.6%. These findings suggest that the use of stimulating materials should be approached with caution, as even slight changes in the amount used can impact methane production.

The Environmental interactions contributed to the processes of settlement and development of the first settlers at southern Peru 15,000 BC. The determination of this process is based on paleoclimatic studies at southern Peru and ethnoarchaeological evidence. The determination of this process is based on paleoclimatic studies of southern Peru and ethnoarchaeological evidence; establishing as a result of this analysis the hypothesis of environmental interaction and territorial occupation of the first hunter-gatherer populations until their consolidation, dominating the geographical space from Tacna. The Disruptive disaster events and their effects on climate during the Peruvian Paleolithic resulted in the origin of local societies that shaped the Tiawanaku societies of the early horizon at Southern Peru and Northern Chile.

This study empirically analyzes the effectiveness of resource optimization utilizing artificial intelligence (AI) within cloud computing environments. It compares systems that have been transitioned from a Monolithic structure to Microservices Architecture (MSA) with those adopting a simple Rehost strategy, to validate the operational efficiency of two systems whose resource efficiency has been enhanced compared to traditional legacy systems. The research is based on systems that determined resource efficiency post-cloud migration using APM tools. It points out the limitations of traditional heuristic operation methods in resource optimization, which lead to issues such as application performance degradation, resource over-allocation, and increased operational costs. This study aims to overcome the conventional resource optimization standards that depended on the average peak usage of CPU and memory infrastructure, by introducing AI-based optimization tools, and applying on-premise standards to cloud and container environments to achieve resource optimization. The paper emphasizes the importance of resource optimization through AI-based automation tools, exploring the possibilities of resolving real-world application performance issues in cloud environments, reducing unnecessary resource usage costs, and cutting down on labor risks and operational expenses. Through this, it presents strategic directions on how AI technology can offer financial and operational advantages in managing cloud resources.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

The effect of the melt cooling rate on the atomic ordering of austenite and, as a consequence, on the martensitic transformation of a nonstoichiometric alloy of the Ni-Mn-In system has been studied. In-situ TEM observations revealed differences in the mechanism of phase transformations of the alloy subjected to different cooling conditions. It is shown that during quenching a high density of antiphase boundaries (APB) is formed and the alloy is in the austenite-martensitic (10M and 14M) state up to a temperature of 120K. In a slowly cooled alloy, a lower APB density is observed, and a two-stage transformation L21/B2 → 10M → 14M occurs in the range of 150–120 K.

Purpose: When it comes to improving citizen service delivery standard and processes, or broadly, management in government (MIG), many reform programs and improvement efforts are ongoing across different ministries, departments, and agencies. This paper is part of a larger empirical research where we are interested to know what those programs and projects are, and how they are doing, and what the gaps are. Design/methodology/approach: Analyzing the publicly available data on the government portal and donors’ website, this article provides an overall idea of current reforms in various places of government. In parallel, field research was conducted through visiting agency offices, observing office environment and mechanisms, and interviewing public managers who are working at district and sub-district level offices of directorates or agencies.Findings: As a trend, state-led development process and the traditional mode of administration have moved to New Public Management based quality and performance approach. All donors have their own strategy framework document like ‘Country Assistance strategy’, ‘Country Operations and Business Plan’, Logical Framework Document, Focus or Priority Streams, etc. Many of the projects are sectoral and agency or ministry specific and have an inherent limitations, due to ‘cadre’ based organizational structural arrangement. So, it is common ‘not to own the projects’, rather ‘using the fund as much as possible anyway within the given project duration’. When the fund ends, implementing units, either government or NGOs, abandon the projects. That is why many projects are actually half done without significant and sustained direction.Originality/value: We can conclude that the typical ‘top-down’ or ‘trickle down’ conception is still dominant in design and implementation of reforms programs and service quality efforts. So, how to reach systemically at the bottom where public managers provide services to citizens, needs even more deliberation.

Policies are adopted and implemented to achieve specific goals. In this regard, the Government of Zambia in 2019 adopted the higher education policy with many objectives which include, the expansion of access to higher education; reduction of gender and other forms of inequity in accessing higher education; the improvement of quality of higher education by increasing funding to higher education institutions, construction, and repair of infrastructure in higher and improvement in the provision of learning materials in higher education institutions (HEIs).This paper, therefore, sought to evaluate the higher education policy of 2019. The four criteria were used namely; effectiveness, equity, policy sustainability, and consistency. Other principles such as political and social acceptability of a policy were not used because the policy is already adopted and being implemented. Further, the principle of efficiency was not used because it would have been problematic to gauge the expenditure against the outcomes.The findings have revealed that the policy to some extent has been effective; some of the objectives such as increased access to higher education and reduction of inequality have been partially achieved. It has been established that the number of students pursuing higher education has been increased to 114,049 in 2020 from 91,969 in 2017. Further, in 2021, 48.5% of scholarships in public universities were awarded to female students while 51.5% were awarded to female students. Further, more students are encouraged to pursue science, technology, engineering, and mathematics (STEM); and more women are pursuing studies in STEM-related fields. However, the policy has not helped to achieve the quality of higher education as funding in public HEIs has not improved. Further, infrastructure remains very poor and inadequate; and access to update and relevant learning materials also remains a challenge in HEIs. However, the policy seems to be duplicated by the recent re-launched Technical Education Vocation Entrepreneurship Training (TEVET) national policy.Given the above findings, it has been recommended that the government among other things improve funding and build infrastructure in public HEIs. There is also a need to harmonise the TEVET national policy with the higher education policy.

Malassezia is a lipid-dependent genus of yeasts known for being an important part of the skin mycobiota. These yeasts have been associated in the development of skin disorders and cataloged as a causal agent of systemic infections under specific conditions, making them opportunistic pathogens. Little is known about the host-microbe interaction of Malassezia spp., and unraveling this implies the implementation of infection models. In this mini review we present different models that have been implemented in the fungal infections study with greater attention in Malassezia spp. infections. These models range from in vitro (cell cultures and ex vivo tissue), to in vivo (murine models, rabbits, guinea pigs, insects, nematodes, and amoebas). We additionally highlight the alternative models that reduce the use of mammals as model organisms, which have been gaining importance in the study of fungal host-microbe interactions. This is due to the fact that these systems have shown to have reliable results, which correlate with those obtained from mammalian models. Example of alternative models are Caenorhabditis elegans, Drosophila melanogaster, Tenebrio molitor, and Galleria mellonella. These are invertebrates that have been implemented in the study of Malassezia spp. infections in order to identify differences in virulence between Malassezia species.

Academic entrepreneurship focuses on commercialization of research. Even though it is practiced worldwide for decades, Bangladesh is a newcomer in this segment. In Bangladesh only 2 Universities have Technology Transfer Offices or TTOs which are established with the sole focus of commercialization of researches of the students and the faculty members of the Universities. This article focuses on worldwide practices of technology transfer and academic entrepreneurial activities and also explores the opportunities and challenges of such entrepreneurs through detail investigation of the existing body of knowledge. Apart from exploring the problems and prospect of academic entrepreneurship in Bangladesh, this article also introduces the concept of Full-Service Knowledge Transfer Office (KTO), which existing literatures do not offer. The authors believe that by establishing such KTOs as a self-sustaining body, it is possible for an academic entrepreneur to stimulate, support and sustain their activities in Bangladesh. The concept of full service KTOs can also become models for other nations, specially the developing ones, to establish and nurture a culture of academic entrepreneurship.

Far-red fluorescent reporter genes can be used for tracking cells non-invasively in vivo using fluorescence imaging. Here, we investigate the effectiveness of the far-red fluorescent protein, E2-Crimson (E2C), for tracking mouse embryonic cells (mESCs) in vivo following subcutaneous administration into mice. Using a knock-in strategy, we introduced E2C into the Rosa26 locus of an E14-Bra-GFP mESC line, and after confirming that the E2C had no obvious effect on the phenotype of the mESCs, we injected them into mice and imaged them over 9 days. The results showed that fluorescence intensity was weak, and cells could only be detected when injected at high densities. Furthermore, intensity peaked on day 4 and then started to decrease, despite the fact that tumour volume continued to increase beyond day 4. Histopathological analysis showed that although E2C fluorescence could barely be detected in vivo at day 9, analysis of frozen sections indicated that all mESCs within the tumours continued to express E2C. We hypothesise that the decrease in fluorescence intensity in vivo was probably due to the fact that the mESC tumours became more vascular with time, thus leading to increased absorbance of E2C fluorescence by haemoglobin. We conclude that the E2C reporter has limited use for tracking cells in vivo, at least when introduced as a single copy into the Rosa26 locus.

Selection of co-belonging fragments from the numerous ceramic findings of an archaeological excavation remains a difficult process of questionable effectiveness, based exclusively on the experience and patience of the conservators. While the screening of the fragments is a central prerequisite and the most important stage of the process of vase reconstruction, established methods based on scientific criteria and guaranteed efficiency for the detection of co-belonging ceramic fragments suggested in the bibliography, do not exist. On the contrary, for methods dealing with the assembly of vases from co-belonging fragments, which is a secondary process that can be done more easily and effectively in an empirical way, there exist numerous studies based on fragment morphology. However, even these are also not implemented because of the time requirements, sheer volume and complexity of the proposed methods, in order for them to be applicable in practice. The proposed methods in this paper are based on thermoremanent magnetization (A/m), which is calculated from the weak magnetic field measurements by a fluxgate-sensor/magnet apparatus forming a three-dimensional orthogonal system. Experimental measurements from fragments of 6 vases show that the magnetization magnitude of co-belonging fragments display similar values, despite the magnetic anisotropy of the ceramic material, since these belong to vases that are made of the same clay and fired under the same conditions. This is the criterion for finding ceramic fragments of the same vase from archaeological excavations. The thermoremanent magnetism directionality of fragments, which is aligned along the geomagnetic field at the same place and time during the vase firing process, as it is configured by their rotational symmetry, defines the position of the fragments on the body of the 6 vases. The shape of the original vase can be reconstructed when only a few non adjacent fragments are available. The proposed measurement apparatus can be used for the construction of a useable portable magnetometer specialized for ceramic surface measurements to achieve the above objectives.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

The purpose of this article is to review a two year long implementation of an electronic health record (EHR) system at the outpatient department of a private hospital in Kathmandu, possibly a first implementation of its kind in Nepal. Procedures: The strategy designed for EHR implementation was based on Professor John P. Kotter's work on successful change management. Main findings: We found that keeping a close watch on the social dynamics affecting adoption decisions among users of the system was crucial for implementing the EHR; this was partly because the project received limited support from an erratically changing hospital leadership and lacked an EHR system suited to the needs of the users. Conclusions: The implementation described in this article is a good lesson on moving from control to drift in information systems implementation, and we hope this work will be useful to health IT professionals working in the space of digital transformation in resource-constrained environments.

The United Nations Sustainable Development Goals call for the eradication of poverty, and China has proposed the Rural Revitalization Strategy based on the achievements of its poverty alleviation efforts in 2020. As a vital component of this strategy, the impact of land transfer on farmers' income growth has become a hot topic in both theoretical and practical sectors. This paper utilizes data from the CFPS database for the years 2010-2018 to construct OLS regression models and a Heckman two-stage model to analyze the effects of land transfers on the incomes of different types and sources among farmers. The empirical results show: First, land transfers do promote income growth among farmers, but the effect is primarily positive for those transferring out land, with negligible impact on those acquiring land. Second, the impact of land transfers varies between different types of income for transferees and transferors. Wage income contributes up to 88.26% to the income growth of transferors, a significantly higher rate than the decrease in business income; however, the increase in business income for transferees does not offset the decline in wage income, leading to no significant change in overall income. Further sensitivity analysis using the Heckman two-stage model confirms the robustness of these findings. The conclusions of this study provide theoretical and empirical evidence to optimize land transfer policies, enhance participation in land transfers, and ultimately achieve the mission of rural revitalization.

Ovariectomy appears to be the best method to control the density of wild ungulate populations. The aim of the present study was to compare two surgical approaches, via the flank and midline, in mouflon’s ovariectomy in field conditions. Twenty female mouflons were enrolled in the study. The animals were divided randomly in two groups, Group F animals were gonadectomized via flank approach, while Group A animals were sterilized via linea alba access. The parameters evaluated were duration of surgery, duration of anaesthesia, recovery time, intra- and post-operative complications, intra-operative nociception and pain in the post-operative period. There were no intra- and post-operative complications. The evaluated parameters showed a very similar trend in both groups. Both techniques are found to be effective and safe in execution.

Recently, the indications for Cochlear Implant (CI) have also been extended to subjects with Single Sided Deafness (SSD) in order to restore binaural hearing. The primary objective of this study was to investigate the advantages of CI following one year of usage in SSD subjects. Secondarily we want to assess the long-term stability of the CI. 57 participants performed a complete audiological assessment (speech audiometry in quiet and in noise and localization test). For each was also evaluated subjective hearing profile (with Speech Spatial and Qualities_SSQ questionnaire) and the impact of tinnitus (with the use of Tinnitus Handicap Inventory_THI questionnaire) After one year of CI usage, we observed a significant improvement in speech-to-noise ratio, in sound localization abilities, in the Speech (p-value 0.001) and Spatial (p-value 0.001) subscales of the SSQ questionnaire and in THI questionnaire (p-value 0.001). The improvements in speech in noise and localization abilities and the reduction of the SSQ and THI questionnaires scores were maintained over time (6th to 60th month follow-up). Only eight participants did not fully utilize the CI. CI in SSD represents an effective method for improving speech recognition in noisy environments, restoring sound localization abilities, reducing tinnitus and improve subjective listening skills.