This study determines the equivalent stress intensity factor (SIF) model that best fits the experimental behavior of low-carbon steel under mixed mode (I and II). The study assessed Tanaka, Richard, and Pook's equivalent SIF models. The theoretical values used for comparison correspond to experimental results in a modified C(T) geometry by machining a hole ahead of the crack tip subjected to fatigue loads with a load ratio of R = 0.1. The comparison involved the SIF for six experimental points and the values computed through the numerical simulation. The Paris, Klesnil, and modified Forman-Newman crack growth models were used with each equivalent SIF to analyze the prediction in the estimated number of cycles. The Klesnil model showed the closest prediction since the error between the calculated and experimentally recorded number of cycles is the lowest. However, the material behavior reflects a reduced crack propagation rate attributed to plasticity in the crack tip. Results suggest that Asaro equivalent SIF conservatively estimates the element lifespan with increasing errors from 2.3% at the start of growth to 27 % at the end of the calculation.

The COVID-19 pandemic halted progress in global vaccine coverage and disrupted routine childhood vaccination practices worldwide. While there is ample evidence of vaccination declines experienced during the pandemic, it is less clear how low-income countries were affected. We executed a systematic review to synthesize the current literature on impacts to routine childhood vaccinations in low-income countries from January 1, 2020 to February 8, 2023. We collected data using an extraction form on Covidence and assessed the quality of studies included in the review using the Risk of Bias in Non-Randomized Studies of Interventions (ROBINS-I) tool. Effect estimates for changes in vaccination during the pandemic were reported and summarized. Factors that influenced changes were grouped into descriptive themes. Thirteen studies, encompassing 18 low-income countries and evaluating 15 vaccines at varying doses, were included in the final review. We found that routine childhood vaccinations during the COVID-19 pandemic varied considerably by vaccine type, location, and phase of the pandemic. Nine different themes were identified as factors that influenced changes in vaccination. Documenting past experiences and lessons learned is crucial for informing preparedness efforts in anticipation of future public health emergencies. Failure to effectively address these things in the next public health emergency could result in a recurrence of declining routine childhood vaccinations.

Global warming may increase the potential evapotranspiration (Etp), thereby affecting the amount of clean water resources available in a region. In this study, the systematic biases in temperature outputs of 24 global climate models (GCMs) under 3 emission scenarios are corrected by using 8 bias correction methods. The trend of Etp in Yangzi River Delta in the 21st century is projected by using 4 Etp calculation formulas. The uncertainty of the projections is estimated and decomposed by using multi-way analysis of variance. The influence of uncertainty on the projected change signal is quantified by using the signal-to-noise ratio. The results show that, relative to the reference period (1971~2000), the annual mean daily Etp in Yangzi River Delta will increase by 0.14~0.17mm/d during the period 2021~2050 and by 0.21~0.41mm/d during the period 2061~2090, respectively. During 2021~2050, the uncertainty of Etp increase projections is dominantly contributed by the main effects of GCM (63%) and Etp calculation formula (24%). During 2061~2090, it is mainly contributed by the main effect of GCM (36%), followed by the main effects of emission scenario (34%) and Etp calculation formula (18%). The increase projections of Etp are generally reliable and robust during the two projection periods.

This paper offers a theoretical and experimental examination of the concurrent production of electricity and heat using photovoltaic thermal (PV/T) technology. The efficiency performance of the PV/T system is meticulously analyzed using MATLAB/Simulink software environments. Notably, the proposed PV/T system shows reliable performance, and its validity is confirmed through experimental validation on a test stand with a single PV/T panel positioned at a 45-degree angle to the horizontal and a 0-degree azimuth angle.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

Abstract: Efforts for carbon emission reduction have been identified as a major climate change mitigation target in the Paris Agreement. The 26th Conference of Parties to the United Nations Framework Convention on Climate Change highlighted the worldwide effort for cleaner and greener mining, urging the mineral industry to embrace greener operational emissions reduction technologies and strategies. Ghana pledged at the Paris Conference to reduce CO2 emissions by 15% and increase renewable energy share to 10% of the national energy mix. Here the fundamental question is how Ghana’s mining industry can contribute to CO2 emission reduction efforts. This paper investigates barriers to low-carbon emission policy implementation among mining companies in Ghana. The questionnaire survey was conducted among Ghana’s four large-scale gold mining companies. As the sample number of available companies is limited, we used a descriptive analysis to assess the responses. The results show that the companies expressed widely different ways to respond to the issues of cost, a government policy/regulations for carbon emission reduction, and the adoption/acquisition of low-carbon technologies. Those companies that are relatively less prepared for this endeavor emphasized the uncertainties of securing sufficient energy in case of using low-carbon technologies. They also expressed a need for more trained workers to handle low-carbon technologies. All companies agreed with a expected high cost of adopting low-carbon options. There was a communication gap with the relevant government ministry about low-carbon mining options where the government should be able to facilitate the involvement of othe low technology providers, such as solar PV installation.

Ralstonia solanacearum is the pathogen responsible for Ralstonia solanacearum, which is soil-borne, infests plant conduits to cause disease.They are not easy to control and are harmful.Therefore the development of a controlled-release agent responsive to the pathogen's soil temperature and moisture conditions could aid in its control. Corn kernel powder is used as a carrier for Tetramycin biopesticide, with various compounds tested for bonding.They were then made by extrusion moulding.Temperature and wetness responsive components, including Pentaerythritol Tetrastearate, Pentaerythritol Tetraoleate, Polyethylene Glycol Stearate, and Polyethylene Glycol Monooleate,are compounded and coated onto Tetramycin cores to form an intermediate shell layer. Finally, Ethyl cellulose(EC)and Hydroxypropyl methyl cellulose(HPMC) are dissolved and sprayed onto the outermost layer to complete the pellet's shell layer.After the evaluation of texture performance test,DSC analysis,TG test,temperature and humidity response performance test, as well as pellet cross-section SEM observation, field effectiveness test, etc., the preferred formulations were screened.The results showed that the preferred Core formulation:Corn kernel powder:Tetramycin aqueous:Xanthan gum mass ratio=13.5:23:2; Intermediate Shell layer:PETS: PETO: PEG400MO mass ratio=10:30:10; and Outer Shell layer: Ethyl cellulose (EC):Hydroxypropyl methyl cellulose (HPMC) mass ratio=5:1.Under soil conditions of high incidence of Ralstonia solanacearum, i.e., sustained warmth (30-35℃) and high humidity (30% moisture content), the formulated pills showed a release rate of 95.18% to 96.24% over a period of 35 days. Moreover, they showed a stepwise cyclic release process under alternating warm and humid-dry and cold conditions.In field tests on tobacco, a relative preventive efficacy of 54.74% was achieved 106 days post-transplanting. Soil bacterial community structure analysis revealed a significant decrease (2.28-2.84 times) in the abundance of Solanaceae Raelia under Tetramycin pellet treatment compared to the control. Additionally, fungal community structure showed highter consistency initially across various soil depths, with diversity differences between soil layers reestablished later (106 days), while the predominant categories of bacteria and fungi remained unchanged.In this study, we successfully developed a nucleoshell-type slow-controlled release pill embedded with Tetramycin. This pill effectively responded to temperature and humidity changes, resulting in high efficacy in disease prevention.This development holds significant promise for effectively improving drug utilization and easing application challenges, offering broad prospects for Ralstonia solanacearum prevention and control in agriculture.

The origin of neurodegenerative diseases is linked to the abnormal folding of disease-associated proteins. The traditional amyloid hypothesis has been a focal point of research, but recent findings suggest a more complex picture. This review explores the role of physiological conformation of aggregation-prone domain (also known as prion-like low complexity domain) and multiple co-misfolded proteins in neurodegenerative diseases. We highlight the importance of targeting multi-heterotypic misfolded proteins for effective treatments and emphasize the irreversible neurodegeneration stemming from the loss of physiological folding in prion-like disease-causing proteins underscores the criticality of refolding. Additionally, we introduce the concept of ReproFold Therapeutics, a novel approach aimed at restoring the cellular prion-like folding of disease-causing proteins to rebuild normal cross-β interactomes and mitigate neurodegeneration. Baicalein, a potential drug candidate for this approach, shows promise in vitro and in animal models. Moreover, prion-like low complexity domains implicated in neurodegeneration are also associated with other disorders such as diabetes, cancers, and mental illnesses. Understanding the core pathology of neurodegenerative diseases and the broader implications of prion-like LC domains could revolutionize healthcare approaches and policies worldwide.

In recent years the number of available chemical pesticides has been significantly reduced and there have been an urgent need for discovery of alternative to chemical pesticides products, as among others the natural zeolites (zeolitic rocks). We determined the mineralogical and chemical composition of a specific and continuous layers of zeolitic rock sample (ZeotP) from Petrota, Ev-ros, Greece and evaluated its oviposition deterrent effect for the olive fruit fly Bactrocera oleae (Diptera: Terphritidae). The tested natural zeolite contained 70 wt. % Clinoptilolite, 18 wt. % Amorphous material, 7 wt. % Feldspars, 4 wt. % Cristobalite and 1 wt. % Quartz. We tested the oviposition deterrent effect of ZeotP mixed or not with an emulsifier adjuvant NU-FILM-P® in water and applied on the surface of olive fruits. The ZeotP oviposition deterrent effect for the ol-ive fly was very high under a series of tested temperatures (17°C, 20°C, 25°C and 30°C) and RHs (23%, 33%, 55%, 75%, 94%). In addition, the ZeotP residual deterrent effect after equable water spraying was high and similar to the respective effect of a pyrethroid insecticide (Decis®). Our results may contribute to an effective control of the olive fruit fly using an alternative to chemical pesticides natural zeolite (zeolitic rocks) product.

Recent satellite measurements of glacier mass balance show mountain glaciers all over the world had generally negative mass balances in the first decades of the 21st century. Mean summer temperatures all over the world rose from 1961-90 to 1991-2020, implying increasingly negative mass balances. We study archived annual balances for 38 Northern Hemisphere glaciers to assess changes within in the 19612020 period. We use a modified doublemass curve to visualize mass balance changes occurring around 1990. Mean balances 196190 were already small negative for many of the studied glaciers and became even more negative in 19912020 for glaciers in the Alps, at high latitudes and in western North America. The largest mass balance changes are for some glaciers in the Alps. We are unable to explain the lack of change in mean balance for one glacier in High Mountain Asia. We find complex changes for eight glaciers in Scandinavia, even including one glacier with positive balance. We explain these changes by visualizing deviations of winter and summer balances from their respective 1961-90 mean values. High winter balances in the 1990s for Scandinavia partly obscured the emerging trend of increasingly negative summer balances, which we expect to continue in the future.

This paper explores the Wilsonian renormalization group of probe-D-branes, focusing on the Dirac-Born-Infeld (DBI) action. The analysis involves deriving the constant of motion and formulating the Wilsonian renormalization group equation. The study extends to the infrared regime, considering both zero and non-zero temperatures. Additionally, thermodynamic aspects related to the functional form of the grand potential are discussed. The investigation provides insights into the renormalization of probe-D-branes and their thermodynamic properties.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

In the process of use and manufacture, carbon fiber foam sandwich structures were often damaged by low-energy impact, resulting in performance degradation. Therefore, it was necessary to study the damage caused by low-speed impact of composite sandwich structures. In this paper, based on Hashin failure criterion, an equivalent finite element model of carbon fiber foam sandwich panel under low velocity impact was established. The model was used to simulate the damage of foam sandwich panel with [±45°/±45°/ (core) /±45°/±45°] ply structure under the impact energy of 10.58J, 21.17J, 31.75J and 42.34J. The simulation results of impact damage depth were compared with the experimental results. The error was less than 10%, which proved the rationality of the impact equivalent model. The model was used to predict and analyze the damage of foam sandwich panels with [±45°/ (core) /±45°], [±45°/ (0°, 90°) / (core) /±45°] and [±45°/ (0°, 90°) (core) / (0°, 90°) /±45°] ply structures under 21.17J impact energy. By comparing and analyzing the damage situation, impact force response time and impact velocity response time, the low energy impact resistance was analyzed. The results showed that increasing the number of ply structure of [±45°] can reduce the impact damage degree and improve the bearing capacity of sandwich panels.

In a context of increasingly necessary energy transition, precise modelling of profiles for low-voltage (LV) network consumers is crucial to enhance hosting capacity. Typically, load curves for these consumers are estimated through measurement campaigns conducted by Distribution System Operators (DSO) for a representative subset of customers or through the aggregation of load curves from household appliances within a residence. With the instrumentation of smart meters becoming more common, a new approach to modelling profiles for residential customers is proposed to make the most of the measurements from these meters. The disaggregation model estimates the load profile of customers on a low-voltage network by disaggregating the load curve measured at the secondary substation level. By utilizing only the maximum power measured by Linky smart meters, along with the load curve of the secondary substation, this model can estimate the daily profile of customers. For 48 secondary substations in our dataset, the model obtained an average symmetric mean average percentage error (SMAPE) error of 4.91% in reconstructing the load curve of the secondary substation from the curves disaggregated by the model. This methodology can allow the estimation of the daily consumption behaviors of the low-voltage customers. In this way, we can safely envision solutions that enhance the grid hosting capacity.

The low-temperature environment significantly inhibits the growth and metabolism of denitrifying bacteria, leading to an excessive concentration of ammonia nitrogen and total nitrogen in sewage treatment plants during the cold season. In this study, an efficient denitrifying strain of heterotrophic nitrification–aerobic denitrification(HN-AD) bacteria named HS2 was isolated and screened from industrial sewage of a chemical factory in Inner Mongolia at 8°C. The strain was confirmed to be Achromobacter spiritinus, a colorless rod-shaped bacterium. When cultured with sodium succinate as the carbon source, a carbon-to-nitrogen ratio of 20-30, a shaking rate of 150-180 r/min, and the initial pH of 6-10, the Strain HS2 exhibited excellent nitrogen removal at 8°C. Through the results of whole-genome sequencing, gene amplification, and gas product detection, the Strain HS2 was determined to possess key enzyme genes in both nitrification and denitrification pathways, suggesting a HN-AD pathway of NH4+-N→NH2OH→NO2--N→NO→N2O→N2. At 8°C, the Strain HS2 could completely remove ammonia nitrogen from industrial sewage with an initial concentration of 127.23 mg/L. Microbial species diversity analysis of the final sewage confirmed Achromobacter sp. as the dominant genus, this indicated that the low-temperature denitrifying strain HS2 plays an important role in nitrogen removal of actual low-temperature sewage.

Background. Implementing mammogram screening means that clinicians are seeing many breast cancers that will never develop metastases. The purpose of this study was to identify subgroups of breast cancer patients who did not present events related to long-term breast cancer mortality, taking into account diagnosis at breast screening, absence of palpability and axillary involvement, and genomic analysis with PAM50. Patients and Methods. To identify them, a retrospective observational study was carried out selecting patients without palpable tumour, without axillary involvement, and a genomic analysis was performed with PAM50. Results. The probability of distant metastasis-free interval (DMFI) of 337 patients was 0.92 (95% CI, 0.90-0.93) at 20 years and 0.96 (95% CI, 0.92-1.00) in 95 patients (28%) with available PAM50 tests. In 22 (23.15%) luminal A tumours and in 9 (9.47%) luminal B tumours smaller than 1 cm and in HER2 and basal type tumours there were no metastatic events (20-year DMFI of 1.00). Conclusion. Patients with nonpalpable breast cancer found at screening with negative nodes are at very low risk. It is possible to identify subgroups without metastatic events by determining the intrinsic subtype and tumour size less than 1 cm. De-escalation of treatment should be considered.

We propose a new methodology for long-time biopotential recording based on MEMS multisensor integrated platform featuring a commercial electrostatic charge transfer sensor. That family of sensors was originally intended for presence tracking in automotive, so the existing setup has been engineered for the acquisition of electrocardiogram, electroencephalogram, electrooculogram and electromyography, designing a dedicated front-end and writing a proper firmware for the specific application. Systematic tests on controls and nocturnal acquisitions from patients in domestic environment will be discussed in detail. The excellent results candidate this technology to provide a low power, unexplored solution to biopotentials acquisition. The technology breakthrough is in that it enables adding this type of functionality to existing MEMS boards at near-zero additional power consumption. For these reasons, they open to additional possibilities for wearable sensing and strengthen the role of MEMS technology in medical wearable applications for long time synchronous acquisition of a wide range of signals.

In recent years, researches on combining wavelet decomposition and convolutional neural network (CNN) together to classify hyperspectral images (HSI) have emerged, and some effective classification models have been proposed and achieved good classification results. However, there are two problems for most of the proposed models. One is the heavy training parameters and the other is that there is no distinction between the classification effectiveness of low frequency and high frequency features after wavelet decomposition. In this paper, a new light-weighted HSI classification model (LLFWCNN) is proposed, which performs multi-layer wavelet decomposition for HSI after dimensionality reduction, and only arranges the low frequency features in a specific stack mode, then classifies them through a well-designed convolutional neural network. Compared with other classification models, the number of parameters is only 2.5% of that of other models. And only the low frequency features after wavelet decomposition are used, while the high frequency features are abandoned. The results showed that compared with the state-of-the-art classification models, LLFWCNN could obtain the same or even better classification results with fewer network parameters and proved that the low frequency features after wavelet decomposition provide LLFWCNN with more favorable information for HSI classification as well.

UV-digital printing belongs to the commonly used method for custom large-area substrate decoration. Despite low surface energy and adhesion, transparent polymer materials, such as polymethylmethacrylate (PMMA) and polycarbonate (PC), represent an ideal substrate for such purposes. The diffuse coplanar surface barrier discharge (DCSBD) in a novel compact configuration was used for substrate activation to improve ink adhesion to the polymer surface. This industrially applicable version of DCSBD was prepared, tested, and successfully implemented for the UV-digital printing process. Furthermore, wettability and surface free energy measurement, X-ray photoelectron spectroscopy, atomic force and scanning electron microscopy evaluated the surface chemistry and morphology changes. The changes in adhesion of the surface and of ink were analyzed by a peel-force and a crosscut test, respectively. A short plasma treatment (1-5 s) enhanced the substrate's properties of PMMA and PC while providing the pre-treatment suitable for further in-line UV-digital printing. Furthermore, we did not observe damage or significant change of roughness affecting the substrate's initial transparency.

In this paper, we use a machine learning method, known as Nonnegative Matrix Factorization, to extract from a given image some new information obtained from a number of color space representations. Such kind of information, termed ``metacolor'', can be considered as a particular color space representation of the image, which can be used to obtain a binary segmentation of the investigated image by distinguishing foreground and background pixels. Some numerical experiments prove that the proposed method shows improved results when compared with common simpler thresholding algorithms.

Saprotrophic fungi are key in global carbon cycling, capable of decomposing lignocellulose in wood. This study, for the first time, explores the influence of oxygen (O2) and temperature on methane (CH4) production by two fungi, Laetiporus sulphureus and Pleurotus sapidus. We examined CH4 formation under varying O2 levels (0 to 98%) and temperatures (17, 27, and 40 °C) when the fungi grew on pine wood, beech wood, and grass under sterile conditions. Our findings reveal a strong dependency of fungal CH4 production on O2 mixing ratios. Methane formation was highest when O2 levels exceeded 5%, whilst no CH4 formation was observed after complete O2 consumption by the fungi. Reintroducing O2 immediately resumed fungal CH4 production. When CH4 formation was normalized to O2 consumption (CH4_norm) a different pattern between species was observed. L. sulphureus showed higher CH4_norm rates with higher O2 levels, whereas P. sapidus showed elevated rates between 0-5% O2. Temperature also significantly influenced CH4 and CH4_norm rates, with the highest production at 27 °C, and comparatively lower rates at 17 and 40 °C. These results demonstrate that O2 levels and temperature are critical in controlling fungal CH4 emissions, a consideration necessary for future CH4 source predictions.

The lung microbiota is a complex community of microorganisms that colonize the respiratory tract of individuals from or even before birth. Although the lungs were traditionally believed to be sterile, recent research has shown that there is a diversity of bacterial species in the respiratory system. Knowledge about the lung microbiota in the newborn and its relationship with bacterial infections is of vital importance to understand the pathogenesis of respiratory diseases in neona-tal patients undergoing mechanical ventilation. In this article, the current evidence on the compo-sition of the lung microbiota in the newborn will be reviewed, as well as its role in the develop-ment of bacterial infections in mechanically ventilated neonates. Although advances in many as-pects of the neonatal intensive care unit care have significantly improved the survival of preterm infants, the diagnosis and treatment of ventilator-associated pneumonia has not progressed in recent decades. Avoiding dysbiosis caused by inappropriate use of antibiotics around birth, as well as avoiding intubation of patients or promoting early removal of endotracheal tubes are among the most important preventive measures for ventilator-associated pneumonia. The use of probiotics and prebiotics to prevent infectious, allergic or metabolic complications in the short or long term constitutes a very important field of research in perinatal medicine.

This paper is an extended version of a previously reported conference paper regarding low power design for NAND Flash. As the number of bits per NAND Flash die increases with cost scaling, IO datapath speed increases to minimize the page access time with scaled CMOS in IOs. The power supply for IO buffers, namely VDDQ, has decreased from 3V to 1.2V, accordingly. In this paper, how a reduction in VDDQ can contribute to power reduction in BL path is discussed and validated. Conventionally, BL voltage of about 0.5V has been supplied from a supply voltage source (VDD) of 3V. BL path power can be reduced by a factor of VDDQ to VDD when BL voltage is supplied from VDDQ. To maintain a sense margin at sense amplifiers, the supply source for BLs is switched from VDDQ to VDD before sensing. As a result, power reduction and equivalent sense margin can be realized at the same time. The overhead of implementing this operation is an increase in BL access time of about 2% for switching the power supply from VDDQ to VDD and an increase in die size of about 0.01% for adding the switching circuit, both of which are not significant in comparison with a significant power reduction in BL path power of NAND die of about 60%. The BL path was designed in 180nm CMOS to validate the design. When the cost for powering SSD becomes quite significant especially for data center, an additional lower voltage supply such as 0.8V dedicated to BL charging for read and program verify operations may be the best option for the future.

Due to the ongoing climate change plants face multiple stress factors (mainly the abiotic ones) simultaneously, which means that the reduced yields of critical crops (including wheat, rice, or barley) can be expected. Therefore, our understanding of the light and temperature sensing mechanisms and related signaling is of primary importance. Herein we present a review focused on the direct sensing (ensured via photoreceptors) of light, which is the main abiotic factor driving the development, phenology, and especially resistance against oxidative stress via the increased accumulation of protective metabolites of crops. Thus, in the following text, special attention is paid to the description of the plant photoreceptors, their mode of action, ranges of perception, and related signaling pathways leading to the activation of target transcription factors. These finally lead to alterations in the expression of target genes related to photoprotection. Due to the focus of our research, genes related to the production of phenolic compounds (PheCs) were selected as a representative group of target genes having a UV-screening, and antioxidative function meaning that their activation and activity of resulting proteins can significantly contribute to the increased tolerance of plants against stress cues.

High temperature (HT) geothermal wells can provide green power 24h a day 7 days a week. Harsh environmental and operational conditions, long-term durability requirements of such wells require special cementitious composites for well construction. This paper reports a comprehensive assessment of geothermal cement composites in cyclic pressure function laboratory tests, field exposures in an HT geothermal well (300-350oC) as well as a numerical model to complement the experimental results. Performances of calcium-aluminate-cement (CAC)-based composites and calcium free cement were compared against reference Ordinary Portland Cement (OPC)/silica blend. The stability and degradation of the tested materials was characterized by crystalline composition, thermo-gravimetric, and elemental analyses, morphological studies, water-fillable porosity, and mechanical properties measurements. All CAC-based formulations outperformed the reference blend both in the function and exposure tests. The reference OPC/silica lost its mechanical properties during the 9-month well exposure through extensive HT carbonation, while properties of the CAC-based blends improved over that period. The Modified Cam-Clay (MCC) plasticity parameters of several HT cement formulations were extracted from triaxial and Brazilian tests and verified against the experimental results of function cyclic tests. These parameters can be used in well integrity models to predict field-scale behavior of the cement sheath under geothermal well conditions.

Amidst escalating environmental concerns, short natural fiber thermoplastic (SNFT) biocomposites have emerged as sustainable materials for the eco-friendly production of mechanical components. However, their limited durability has prompted research into the experimental evaluation of the deterioration of the mechanical characteristics of SNFT biocomposites, particularly under the influence of ultraviolet rays. However, conducting tests to evaluate the mechanical properties can be time-consuming and expensive. In this study, an artificial neural network (ANN) model was employed to predict the mechanical properties (tensile strength) and the impact performance (resistance and absorbed energy) of polypropylene reinforced with 30 wt.% short flax or wood pine fibers (referred to as PP30-F or PP30-P, respectively). Eight parameters were collected from experimental studies. The ANN input parameters comprised nondestructive test results, including mass, hardness, roughness, and natural frequencies, while the output parameters were the tensile strength, the maximum impact load and absorbed energy. The model was developed using the ANN toolbox in MATLAB. The linear coefficient of correlation and mean squared error were selected as the metrics for evaluating the performance function and accuracy of the ANN model. They calculate the relationship and the average squared difference between the predicted and actual values. The data analysis conducted by the models demonstrated exceptional predictive capability, achieving an accuracy rate exceeding 96%, which was deemed satisfactory. For both the PP30-F and PP30-P biocomposites, the ANN predictions deviated from the experimental data by 3, 5, and 6% about the impact load, absorbed energy, and tensile strength, respectively.

A facile and environmentally benign method for a single-phase barium titanate synthesis in water vapor medium was studied to reveal the mechanism of phase transformation of the initial simple oxides mixture and estimate the capability of the product to be used as a raw material for low-frequency dielectric ceramics. The composition and structure of the reaction mixture treated in vapor at 130…150 °C as well as 230 °C for various time were investigated by means of XRD, SEM, HRTEM, EDX, and FTIR methods. The kinetics of the occurring phase transformation was described by Johnson-Mehl-Avrami-Erofeev equation. The reaction between the initial oxides was considered as a topochemical process with an apparent activation energy of 74…80 kJ mol^-1. A crucial role in this process belonged to the water vapor medium, which facilitated the generation of the reaction zone and its spreading inward the solid particles. The synthesized tetragonal barium titanate powder (mean particle size of 135 ± 24 nm) was sintered by a conventional technique at 1250 °C to obtain ceramics with grains of about 2 μm. Capacitance measurements performed a dielectric constant and loss tangent of ceramics, which reached 3879 and 6.7 10^-3, respectively, at 1 kHz and room temperature.

Structural health monitoring (SHM) is critical for ensuring the safety of infrastructures like bridges. This article presents a digital twin solution for SHM of railway bridges using low-cost wireless accelerometers and Machine Learning (ML). The system architecture combines edge on-premises computing and cloud analytics to enable efficient real-time monitoring and complete storage of relevant time-history datasets. After train crossings, accelerometers stream raw vibration data, which is processed in the frequency domain and analyzed via machine learning to detect anomalies indicating potential structural issues. The digital twin approach is demonstrated on an in-service railway bridge, where vibration data was collected over two years under normal operating conditions. By learning allowable ranges for vibration patterns, the digital twin model identifies abnormal spectral peaks, suggesting changes in structural integrity. The long-term pilot proves that this affordable SHM system can provide automated and real-time warning of bridge damage and also supports the use of in-house designed sensors of lower-cost and edge computing capabilities than those used in the demonstration. The successful on-premises-cloud hybrid implementation provides a cost effective and scalable model for expanding monitoring to thousands of railway bridges, democratizing SHM to improve safety by avoiding catastrophic failures.

The orexin/hypocretin neuropeptide family has emerged as a focal point of neuroscientific research following the discovery that this family plays a crucial role in a variety of physiological and behavioral processes. These neuropeptides serve as powerful neuromodulators, intricately shaping autonomic, endocrine, and behavioral responses across species. Notably, they serve as master regulators of vigilance and stress responses; however, their role in complex processes such as food intake, metabolism, and thermoregulation warrant further investigation. This narrative review provides a journey through the evolution of our understanding of the orexin system, from its initial discovery to the promising progress made in developing orexin derivatives. It goes beyond conventional boundaries, striving to synthesize the multifaceted activities of orexins. Special emphasis is placed on domains such as stress response, fear, anxiety, and learning, in which the authors contributed to the literature with original publications. This article demonstrates the orchestrating role of the orexins in several intricate and integrative physiological processes. It also overviews the advancement of orexin pharmacology, which has already yielded some promising successes, particularly in the treatment of sleep disorders. This interdisciplinary approach to studying neuropeptides unveils their significance as vital connectors between transient functional changes and lasting structural adaptations. Ultimately, it advances our understanding of the intricate physiological and behavioral contributions of the orexin/hypocretin neuropeptide family.

Low-cost monitors have made possible for the first time measurements of long-term (months to years) potential indoor exposures to fine particles. Indoor and outdoor measurements made over nearly 5 years (2017-2021) by the largest network of low-cost monitors in the United States (PurpleAir) are compared to the prevalence of adult smokers in 1650 Zip codes within the three West Coast states of California, Oregon, and Washington. The results show that mean indoor exposures above the 75th percentile of adult smoking prevalence are more than 50% higher than those below the 25th percentile. Mean outdoor concentrations are also elevated, but by a smaller amount (20%). Both comparisons are significant at the p<0.001 level. The elevation of the PM2.5 concentrations with increasing smoking prevalence is evidence of environmental disparities in income, education, and other socioeconomic indices..

In this experiment, the fermented pineapple residue (FPR) was replaced with 0% (CON), 25% (T25) and 50% (T50) in the diet based on silage royal grass roxb for 30 days in the fattened fatten bulls to evaluate the effect of FPR on growth performance, serum indicators and rumen characteristics.Thirty Simmental calves were selected and divided into three groups according to a completely random design.The temperature and humidity of the cowshed shall be measured every day.Rectal temperature and blood of cattle were measured, and blood and immune markers were measured.The results showed that the rectal temperature decreased significantly when adding 25% fermented pineapple residue (P<0.05), and the rectal temperature decreased significantly when adding 50% fermented pineapple residue (P<0.01).The content of T4 and TC in serum of cattle in T50 group was significantly lower than that in the control group (P<0.01), and the content of T3 was significantly higher than that in the control group (P<0.05), and the content of CR was significantly lower than that in the control group (P<0.01). Fermented pineapple residue can indeed improve the oxidative (heat) stress resistance of finishing cattle. In the correlation experiment, bacterial genera such as Succinniclassicum, Melainabacteria, Lachnospiraceae, and Fibrobacteres all showed significant or extremely significant correlations with heat stress-related indicators.

The aim of this work is to provide a full description of how air temperature and solar radiation induce changes in the land cover over an Antarctic site. We use shortwave broadband albedo (albedo integrated in the range 300-3000 nm) from a spaceborne sensor and from field surveys to calculate the monthly relative abundance of landscape units. Field albedo data were collected using a portable albedometer over seven landscape units: clean fresh snow; clean old snow; rugged landscape composed of dirty snow with disperse pyroclasts and rocky outcrops; dirty snow; stripes of bare soil and snow; shallow snow with small bare soil patches; bare soil. MODIS MCD43A3 daily albedo product was downloaded using the Google Earth Engine API from the 2000-2001 season to the 2020-2021 season. Each landscape unit was characterized by an albedo normal distribution. The monthly relative abundance of the landscape units were calculated by fitting a linear combination of the normal distributions to the histogram of the MODIS monthly mean albedo. The monthly relative abundance of the landscape unit consisting of rugged landscape composed of dirty snow, with dispersed clasts and small rocky outcrops exhibits a high linear positive correlation with the monthly mean albedo (R2=0.87) and a high linear negative correlation with the monthly mean air temperature (R2= 0.69). The increase of the solar radiation energy flux from September to December coincides with the decrease of the relative abundance of the landscape unit composed of dirty snow with dispersed clasts and small rocky outcrops. We propose a mechanism to describe the evolution of the landscape: uncovered pyroclasts act as melting centres favouring the melting of surrounding snow. Ash does not play a decisive role in the melting of the snow. The results also explain the observed decreasing of the thaw depth of the permafrost on the island in the period 2006-2014, resulting from an increase in the snow cover over the whole island.

Recent advancements have revolutionized interplanetary spacecraft missions by combining low-thrust propulsion systems with planetary Gravity-Assist (GA) maneuvers. This study investigates/improved a novel dual-step efficient-robust homotopy algorithm, grounded in indirect optimal control principles, to analyze fuel-optimal bang-bang control problems. The methodology integrates efficient techniques, including the homotopic method, compatible normalization, and improved switching function detection, aimed at enhancing optimal convergence in solving low-thrust gravity-assist spacecraft missions. To illustrate practical application, an Earth-to-Jupiter interplanetary scenario utilizing Mars-GA is examined. Results demonstrate the algorithm's superior efficacy in achieving fuel efficiency, robust convergence, and remarkable accuracy compared to existing solutions.

Herpes simplex virus type 1 (HSV-1) is a lifelong pathogen characterized by asymptomatic latent infection in the trigeminal ganglia (TG) with periodic outbreaks of cold sores caused by virus reactivation in the TG and subsequent replication in the oral mucosa. While antiviral therapies can provide relief from cold sores, they are unable to eliminate HSV-1. We provide experimental results that highlight non-thermal plasma (NTP) as a new alternative therapy for HSV-1 infection that would resolve cold sores faster and reduce the establishment of latent infection in the TG. Additionally, this study is the first to explore the use of NTP as a therapy that can both treat and prevent human viral infections. We investigated the antiviral effect of NTP using an in vitro model for HSV-1 cold sores, involving the application of NTP from two separate devices to cell-free HSV-1, HSV-1-infected cells, and uninfected cells. We found NTP reduced the infectivity of cell-free HSV-1, reduced viral replication in HSV-1-infected cells, and diminished the susceptibility of uninfected cells to HSV-1 infection. This triad of antiviral mechanisms of action suggest the potential of NTP as a therapeutic agent effective against HSV-1 infection.

Clinical work conducted over the last seventeen years at the EEG Institute in Los Angeles and by other neurofeedback providers around the world has demonstrated the utility of extending frequency-based neurofeedback deep into the infra-low frequency (ILF) region, using the method of endogenous neuromodulation described herein. The method is characterized by the absence of any overt reinforcements, which makes it possible to extend the clinical reach to extremely low frequencies. As the training frequency is lowered, the signal becomes more difficult to discriminate, and ultimately it can only be discerned by the brain itself, in the process of endogenous neuromodulation. The method emulates how the brain does skill learning in general: It must observe itself performing the skill, with feedback on its performance. While the immediate target of ILF neurofeedback is enhanced self-regulatory competence--with symptomatic relief and functional recovery the secondary consequences, progressive lowering of the target frequencies has led to improved outcomes in application to challenging dysfunctions such as episodic suicidality, migraine, seizures, and bipolar mood swings. The work has also yielded insights into how the frequency domain is organized. The training proceeds best at frequencies that are specific to each individual, and these are referred to as optimal response frequencies (ORFs). These frequencies differ for various placements but stand in two fixed relationships to one another, one that holds over the EEG spectral range, and another that holds over the entire ILF range. Training in the ILF region engages the dynamics of the glial-neuronal networks, which govern tonic, resting state regulation. The collective clinical experience with ILF neuromodulation within a large practitioner network supports the case for making protocol-based, individualized ‘homeodynamic’ regulation a therapeutic priority, particularly for our most impacted clinical populations: addiction, trauma formations, traumatic brain injury, and the dementias. The case is made for further outcome studies and foundational research.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

Background and objectives: Musculoskeletal (MSK) pain significantly impacts physical activity and quality of life in the elderly, potentially influencing mortality. This study explored the relationship between MSK pain, physical activity, muscle mass, and mortality among older adults. Material and Methods: We studied 1000 participants of the Korean Longitudinal Study on Health and Aging (KLoSHA), a prospective, population-based cohort study of people aged 65 years or older. Survival status was tracked over a 5-year period. Correlations between Low back pain (LBP), knee pain, regular exercise, appendicular skeletal muscle mass (ASM), and other variables were analyzed. Logistic regression analyzes were used to identify independent risk factors for mortality. Results: Of the total participants, 829 (82.9%) survived after a 5-year period. Survivors tended to be younger, had a higher BMI, and were more active in regular exercise. In contrast, non-survivors exhibited a higher prevalence of both LBP and knee pain, along with increased instances of multiple MSK pain. Lower ASM correlated moderately with LBP and knee pain, whereas higher ASM was associated with regular exercise Lower ASM was moderately associated with LBP and knee pain, while higher ASM correlated with engagement in regular exercise. There was a moderate correlation between LBP and knee pain, both of which were associated with a lack of regular exercise. Age, sex, ASM, and regular exercise were significant predictors, even though MSK pain itself did not directly predict all-cause mortality. Conclusions: This study demonstrated the independent association between ASM, regular exercise, and mortality. Although MSK pain did not directly correlate with all-cause mortality, the non-survivor group had higher levels of both single and multiple MSK pain. Recognizing the interplay of MSK pain, physical activity, and muscle mass for older adults, the research underscores the need for holistic strategies to enhance health outcomes in older individuals with MSK pain.

Through long-term Rayleigh lidar observations during 2010-2022, atmospheric gravity wave (AGW) activities in the middle atmosphere (30–65 km) are statistically investigated at Haikou (110.3°E, 19.9°N) in China. In total, 827 quasi-monochromatic AGW events are identified from the lidar dataset, and the vertical wavelength, observed wave period, and vertical propagation direction of dominant waves are extracted for each AGW event by analyzing the power spectra of wave-induced temperature perturbations. It is revealed that 81.7% of all AGW events were associated with upward-propagating waves, and the proportion of upward-propagating AGWs reached a maximum in autumn and a minimum in winter. The most common vertical wavelengths and wave periods were 6–11 km and 4–10 hours, respectively. In particular, 68 AGW events associated with simultaneous upward and downward propagating waves were observed by lidar, corresponding to 8.2% of the events. The occurrence of such special AGW phenomena is qualitatively discussed, and multiple formation mechanisms may exist. Comparisons are made with previously reported lidar observation results, and the statistical features of AGW activity in the low-latitude middle atmosphere may vary over a relatively wide range depending on the location and altitude. However, a majority of AGWs propagate upward in the middle atmosphere.

This study aimed to investigate the interactions between corn particle size (PS) and conditioning temperature (CT) on the performance, carcass traits, intestinal morphology, and immune responses in broilers fed a corn-soybean meal-based diet. A total of 360, one-day-old male broiler chicks (Ross 308) were randomly allocated into six dietary treatments in a 2×3 factorial arrangement, consisting of two corn PS (finely ground with geometric mean diameter (GMD) of 357 µm (PSF) vs. coarsely ground corn with GMD of 737 µm (PSC), and three CT [unconditioned (CTU), conditioned at 75◦C (CT75) and 90◦C (CT90)]. Birds accommodated in 30 pens with five replicates and 12 chicks per each. There was no interaction between corn PS and CT on growth performance and immune response of broilers at any growth phases. However, during the starter (0-10d) period, the average daily weight gain (ADWG) and feed conversion ratio (FCR) of PSF-fed birds were significantly improved compared to those fed PSC (P<0.05). During the starter (0-10d) and grower (11-24d) periods, increasing the conditioning temperature of corn increased the ADWG, while in the starter phase only the CT75 caused a lower FCR (P<0.05). Broilers fed PSF corn showed lowest FCR during the finisher (25-42d) period compared to those fed PSC (P<0.05). Conditioning corn at 75ºC reduced FCR during the finisher (25-42d) period compared to the birds fed CTU and CT90 corn (P<0.05). In whole experimental periods (1-42d), PSF and CT75 treatment increased the ADWG compared to the PSC and CTU (P<0.05). The CT75 treatment improved primary total anti-sheep red blood cell (SRBCs) titer (IgT) and IgM and secondary IgT and IgG responses compared to the other experimental groups (CTU and CT90) (P<0.05). No significant PS × CT interaction was found on Newcastle disease (ND) antibody titer of broiler chickens (P>0.05). Feeding CT75 corn reduced duodenum and jejunum relative length compared to the birds fed diets containing CTU corn. Significant PS×CT interactions (P<0.05) were observed for villus height, villus height to crypt depth, crypt depth, muscle thickness, and absorption surface area of jejunum. The highest carcass yield observed in PSF-CT75-group (P<0.05). In conclusion, the use of finely ground corn (PSF) conditioned at 75℃ (CT75) was beneficial to growth performance, development of the digestive tract, jejunum histomorphometry and the immune responses of broilers.

In this study, alfalfa silage with different packing densities (500 kg/m3, 600 kg/m3 and 700 kg/m3) were set up under outdoor high temperature and indoor normal temperature. The chemical composition, fermentation quality and microbial community of alfalfa silage were analyzed. The results showed that DM and WAC content decreased with the increase of density. When the density is 600kg/m3, CP content reaches the maximum and ADF content is the lowest. Temperature has a certain effect on alfalfa silage. The content of Lactobacillus plantarum fermented at high temperature is lower than that fermented at normal temperature. At the same time, the content of Lactobacillus plantarum decreased with the increase of packing density. However, the content of Lactobacillus plantarum was the lowest when the packing density was 600 kg/m3 at high temperature. In summary, this study explained the effects of different temperature and density on alfalfa fermentation quality and microbial community, and clarified that the density should be reasonably controlled within 600 kg/m3 during alfalfa silage, providing theoretical support for production practice.

Understanding the evolution patterns in patients diagnosed with acute myeloid leukemia (AML) after therapy is relevant due to the dismal outcome still present in refractory or relapsed AML patients. We performed a retrospective, single-center study to evaluate the mutation profile in paired samples obtained at the time of diagnosis and at the onset of progressive or refractory disease in patients diagnosed with AML through a commercial next-generation sequencing (NGS) panel. In total, 62 patients were analyzed. Of these, 28 patients received ICT, and 34 patients underwent low-intensity treatments. In LIT patients, there were emergent mutations at progressive disease in a 64% (22/34) of the patients. Emergent mutations in the RAS-MAPK signaling pathway were observed in 35.9% (12/34) , corresponding to 54.5% of all patients with emergent mutations (12/22). These were found in 12/22 patients that received venetoclax in combination with hypomethylating agents. Six presented mutations in genes related to the RAS-MAPK pathway. Emerging mutations are frequently observed at progressive AML disease after therapy. In patients treated with LIT, mutations in RAS-MAPK signaling pathway might have a key role on the secondary clinical resistance, not only if they are present at diagnosis, becoming a potential target for the development of new drugs.

Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

The study focuses on a novel porous TiNi-based material for ophthalmic orbital implants which was produced by self-propagating high-temperature synthesis (SHS) and, after proper surface modification, possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

A problem of efficacy of crystal growth methods for crystallization from solution or melt has been investigated. Axial vibrational control (AVC) technique was considered as a perspective method to manage both heat-mass transfer and chemical component composition of the melts in the case of crystallization of complex chemical compounds. Numerical modeling and the search for generalized dependencies made it possible to predict the AVC parameters that provide optimal heat and mass transfer modes for creating flat liquid-solid interfaces, as well as the component composition of dissociated melts of various chemical compounds – Ge, NaNO3, CdTe.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

We use the Stefan-Boltzmann law to derive and investigate what we will call the black hole CMB temperature luminosity. Interestingly, the CMB luminosity is always the same for every black hole at a luminosity distance equal to the Schwarzschild radius, which is fully valid in black hole cosmology, a topic that is actively discussed to this day. The CMB black hole luminosity is always the same , regardless of the mass of the black hole. This is in contrast to the Bekenstein-Hawking luminosity, which is linked to the Hawking temperature, that is mass dependent.

Structural health monitoring (SHM) has become paramount for developing cheaper and more reliable maintenance policies. The advantages coming from adopting such process have turned out to be particularly evident when dealing with plated structures. In this context, state-of-the-art methods are based on exciting and acquiring ultrasonic guided waves through a permanently installed sensor network. A baseline is registered when the structure is healthy, and newly acquired signals are compared to it to detect, localize and quantify damage. To this purpose, the performance of traditional methods based on tomographic algorithms has been overcome by machine learning approaches, which allow processing a larger amount of data without losing diagnostic information. However, to date, no diagnostic method can deal with varying environmental and operational conditions. This works aims to develop a framework for mitigating the impact of temperature variations on ultrasonic guided wave-based SHM through generative artificial intelligence. A variational autoencoder and singular value decomposition were combined to learn the influence of temperature on guided waves. After training, the generative part of the algorithm was used to reconstruct signals at new unseen temperatures. Moreover, a refined version of the algorithm called forced variational autoencoder was introduced to further improve the reconstruction capabilities. The accuracy of the proposed framework was demonstrated against real measurements on a composite plate.

Spodoptera frugiperda (Lepidoptera: Noctuidae) commonly known as fall armyworm was first detected in Uganda in 2016 and has spread to all the maize-growing districts. Different methods have been deployed to control this pest. However, there is a limited understanding of the role of the environment and farmers' practices on the incidence and damage by S. frugiperda in Uganda. This study, therefore, assessed the abundance of S. frugiperda and leaf damage levels in three different districts and explored the association between agronomic practices, crop phenology and weather parameters on S. frugiperda damage and abundance in smallholder farmers’ maize fields using a longitudinal monitoring survey in 69 farmers’ fields of Kole, Kiryandongo and Nakaseke for three seasons. Leaf damage and incidence of damaged plants differed significantly between locations and seasons. Leaf damage and abundance of larvae varied significantly in the different growth stages. Conservation tillage resulted in reduced leaf damage. No significant relationship was observed between pesticide or fertilizer use with S. frugiperda leaf damage. There were non-significant negative relationships between leaf damage and rainfall. Timely and vigilant scouting, proper timing of control measures, minimum tillage practices, and crop diversity should be included in an IPM strategy for S. frugiperda.

Temperature-responsive separation membranes can significantly change their permeability and separation properties in response to changes in their surrounding temperature, improving efficiency and reducing membrane costs. This study focuses on the modification of commercial polyvinylidene fluoride (PVDF) membranes with amphiphilic temperature-responsive copolymer and inorganic nanoparticles. We prepared an amphiphilic temperature-responsive copolymer which the hydrophilic poly(N-isopropyl acrylamide) (PNIPAAm) was side-linked to a hydrophobic polyvinylidene fluoride (PVDF) skeleton. Subsequently, PVDF-g-NIPAAm polymer and graphene oxide (GO) blended with PVDF to prepare temperature-responsive separation membranes. The results showed that temperature-responsive polymers with different NIPAAm grafting ratios were successfully prepared by adjusting the material ratio of PVDF to NIPAAm. PVDF-g-NIPAAm was blended with PVDF with different grafting ratios to obtain separate membranes with different temperature responses. GO and PVDF-g-NIPAAm formed a relatively stable hydrogen bond network, which improved the internal structure and mechanical properties of the membrane without affecting the temperature response, thus extending the service life of the membrane.

The pursuit of more efficient transport has led engineers to develop a wide variety of 1 aircraft configurations with the aim of reducing fuel consumption and emissions. However, these 2 innovative designs introduce significant aeroelastic couplings that can potentially lead to structural 3 failure. Consequently, aeroelastic analysis and optimization has become an integral part of modern 4 aircraft design. In addition, aeroelastic testing of scale models is a critical phase in aircraft devel- 5 opment, requiring accurate prediction of aeroelastic behaviour during scale model construction to 6 reduce costs and mitigate risks associated with full-scale flight testing. Achieving a high degree of 7 similarity between the stiffness, mass distribution and flow field characteristics of scaled models 8 and their full-scale counterparts is of paramount importance. However, achieving similarity is 9 not always straightforward due to the variety of configurations of modern lightweight aircraft, as 10 identical geometry cannot always be directly scaled down. This configuration diversity has a direct 11 impact on the aeroelastic response, necessitating the use of computational aeroelasticity tools and 12 optimization algorithms. This paper presents the development of an aeroelastic scaling framework 13 using multidisciplinary optimization. Specifically, a parametric Finite Element Model (FEM) of the 14 wing is created, incorporating parameterisation of both thickness and geometry, primarily using 15 shell elements. Aerodynamic loads are calculated using the Doublet Lattice Method (DLM) em- 16 ploying twist and camber correction factors, and aeroelastic coupling is established using infinite 17 plate splines. The aeroelastic model is then integrated within an Ant Colony optimization (ACO) 18 algorithm to achieve static and dynamic similarity between the scaled model and the reference wing. 19 A notable contribution of this work is the incorporation of internal geometry parameterisation into 20 the framework, increasing its versatility and effectiveness.

To address friction and wear challenges in dry contacts, manufacturers often employ self-lubricating materials. Graphite and its derivatives stand out as particularly suitable due to their exceptional tribological properties. However, under intense friction conditions, graphite can experience a decline in lubricating efficiency due to severe abrasive wear. This abrasive damage results in elevated activated carbon surfaces with increased surface energy, fostering greater adhesion between sliding surfaces. The low friction coefficient of graphite is not an inherent property but rather a consequence of water vapor adsorption by the material. Beyond 150°C, desorption of the vapor occurs, leading to a transition in the friction coefficient from µ=0.1 to µ=0.6. To address this issue, impregnation solutions for self-lubricating materials have been developed, with various compositions tailored to specific objectives. Common types include molybdenum disulfide, soft metals, or polymers. In this predominantly experimental study, the impact of polymer impregnation on the evolution of friction force and wear rate in graphite material bearings subjected to a dry fretting contact under severe thermal stresses at 270°C was investigated. Additionally, the mechanical stresses in the bearings throughout different phases of our tests were analyzed using a numerical model.

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

Milled MgH2, NaAlH4, MgH2–10NaAlH4, MgH2–30NaAlH4, MgH2–50NaAlH4, and MgH2–2Ni-10NaAlH4 samples were prepared by milling in hydrogen atmosphere (reactive mechanical milling, RMM). Decomposition temperatures of milled MgH2, NaAlH4, MgH2–10NaAlH4, and MgH2–30NaAlH4 were examined in a Sieverts-type hydrogen-absorption and release apparatus, in which the hydrogen pressures were kept constant during hydrogen absorption or release. As the content of NaAlH4 in the sample increased, the temperature at the highest peak in the ratio of increase in Hr to increase in T, dHr/dT, versus T curve decreased. The higher content of NaAlH4 is believed to have made effects of reactive mechanical milling stronger. Effects of the NaAlH4 content on the temperatures of intermediate reactions were studied for MgH2 – NaAlH4 composites. Phase formation in the cycled MgH2–50NaAlH4 were investigated. The hydrogen-storage properties of MgH2–30NaAlH4 were compared with those of Mg-based alloys in which oxide, halides, or fluoride was added.

The results of numerical experiments with the chemistry-climate model of the Institute of Numerical Mathematics of the Russian Academy of Sciences - Russian State Hydro-Meteorological University (INM-RSHU CCM) in comparison with the MERRA2 reanalysis data are presented. To assess the impact of sea surface temperature (SST) on stratospheric processes and the ozone layer, numerical experiments were carried out for scenarios corresponding to the El Niño and La Niña Southern Oscillation phases. It is shown that the El Niño phase contributes to the enhancement of heat and mass transfer to the polar stratosphere, which strengthen the Brewer-Dobson circulation and the flux of wave activity that affect the zonal wind. As a result, during El Niño, the probability of sudden stratospheric warming increases and the stratospheric polar vortex (SPV) weakens, re-sulting in an increase in total polar stratospheric ozone. The La Niña phase, on the contrary, is accompanied by a weakening of heat and mass transfer from the troposphere to the stratosphere, as a result of which the stratospheric polar vortex strengthens and the total column ozone decreases. It is shown that the effect associated with the Southern Oscillation is more pronounced in the Northern Hemisphere than in the Southern Hemisphere. Numerical experiments were also carried out for scenarios in which the sea surface temperature was set corresponding to the early 1980s, and the results were compared with calculations in which the SST was set corresponding to the late 2010s. This allowed us to assess the influence of the multiyear trend in the SST increase on stra-tospheric processes and the ozone layer. It was shown that the SST increase is most pronounced in the Arctic, which corresponds to the phenomenon of "Arctic amplification", and therefore, the heat and mass transfer to the stratosphere increases in the Northern Hemisphere, which contributes to some weakening of the SPV and increase of the total column ozone. But, compared to the Southern Oscillation, the influence of the SST trend on the SPV and total column ozone is much weaker and is observed mainly in the Northern Hemisphere.

Climate change is one of the most concerning global issues and has the potential to influence every aspect of human life. Like different components of society, it can impose significant adverse impacts on pavement infrastructure. Although several research efforts have focused on studying the effects of climate change on natural and built systems, its impact on pavement performance has not been studied extensively. Due to the weather effect the lifetime of pavement is getting lower on the other hand maintenance cost is getting higher and higher. The data has been collected from LTTP website and as a site The State of Texas has been considered. The primary objective of this project is to quantify the effect of temperature as well as precipitation changes on pavement response and performance prediction using the ARIMA model and develop a logistic regression model to analyze the forecast data.

A novel low-power MOS-only voltage reference is presented. The Enz-Krummenacher-Vittoz (EKV) model is adopted to provide a new perspective on the operating principle. The normalized charge density, introduced as a new variable, serves as an indicator when trimming the output temperature coefficient. The proposed voltage reference consists of a specific current generator and a 5-bit trimmable load. Thanks to the well-match between the current source stage and the output stage, the non-linear temperature dependence of carrier mobility is automatically canceled out. The circuit is designed in 55 nm COMS technology. The operating temperature ranges from -40 ∘C to 120 ∘C. The average temperature coefficient of the output voltage can be reduced to 21.7 ppm/∘C by trimming. The power consumption is only 23.2 nW with a supply voltage of 0.8 V. The line sensitivity and the power supply rejection ratio at 100 Hz are 0.011 %/V and -89 dB respectively.

To improve the adaptability of aerial reflective opto-mechanical structures to low-temperature environments, an optimized thermal control design is proposed. Firstly, the relationship be-tween conventional heating methods and axial/radial temperature differences of mirrors with different shapes is analyzed. Based on heat transfer analyses, it is pointed out that optimized thermal control design is necessary to ensure the temperature uniformity of the fused silica mirror and take into account the temperature level when working in low temperature environ-ments. A thermal control scheme based on temperature negative feedback variable power zone heating is proposed for the characteristics of aerial electro-optics systems. Using the thermal control scheme at low temperatures ensures that the average temperature of the mirror fluctu-ates slowly and slightly around 20℃. At the same time, the temperature differences within a mirror and between the primary mirror and the secondary mirror can be controlled within 5℃. Thereby, satisfactory image quality is obtained.

Nutrition and calorie intake are associated with subtle changes of thyroid function tests in subjects with intact Hypothalamic-Pituitary-Thyroid axis. Iodine deficiency and extreme fluctuations in calorie intake, such as those occurring during periods of starvation or overfeeding could lead to alterations of thyroid hormones. The dietary macronutrient composition could also influence the thyroid function. Recently, Low-Glycemic Load (LGL) diets are very popular and effective in the treatment and/or prevention of several medical conditions, including diabetes, obesity, cardiovascular disease, and epilepsy. In this review, we report the available data from the literature regarding the association between LGL diets and thyroid function or dysfunction. Unfortunately, there are only a few studies in this field, with inconsistent findings.

In recent years, green and healthy foods have attracted much attention. Plant-based foods have become a new trend to replace animal-derived foods. In this study, we used walnut and purple rice as the primary raw materials to produce yogurt. The process included boiling, mixing, grinding, inoculation, fermentation, and sterilization. We then analyzed the similarities and differences between the resulting walnut purple rice yogurt and unfermented walnut purple rice milk, as well as dairy-based yogurt, in terms of physical chemistry, flavor, and sensory characteristics. We also examined the similarities and differences between fermented walnut purple rice milk and conventional warm yogurt. The study results revealed that walnut purple rice yogurt exhibited greater viscosity than walnut purple rice milk and conventional dairy-based yogurt. Additionally, the former displayed enhanced stability and recovery ability. Notably, distinguishable differences were observed between the three types of yogurts in terms of the presence of unknown volatiles and the umami signal as indicated by electronic nose/tongue and GC-IMS analyses. The umami flavour of walnut purple rice yogurt surpasses that of traditional dairy-based yogurt, whilst its salty taste is lower than that of walnut purple rice milk. Despite possessing a weaker aroma than dairy-based yogurt, it is more potent than walnut purple rice milk. Additionally, its relative abundance of olefins, ketones, and alcohols enhances its unique flavour profile, surpassing both other options. Based on sensory analysis, it can be deduced that walnut purple rice yogurt has the highest overall acceptance rate.

This paper proposes a new method for network screening on rural low-volume roads. These roads are important as they provide critical access to agricultural land and tourist attractions. Most low-volume roads belong to the lowest functional class (local rural roads) and thus are built to lower design standards. The conventional hot spot network screening techniques may not be appropriate for low-volume roads due to the sporadic nature of crashes occurring on these roads. Contrarily sophisticated network screening approaches require extensive roadway and traffic data that are often unavailable to local agencies for lack of resources, and/or lack of technical expertise. This research attempts to address these obstacles in low-volume roads network screening which aims to identify candidate sites for safety improvements. The research used an extensive low-volume road sample from the state of Oregon and the Empirical Bayes expected number of crashes in developing the proposed models for network screening. The proposed models do not require exact measurement of roadway geometric features as all geometric variables were classified into categories that are easy to compile by local agencies. Further, the method could be used with and without traffic data, without compromising the effectiveness of the network screening process.

High-grade gliomas are extremely fatal tumors, marked by severe hypoxia and therapeutic resistance. Autophagy is a cellular degradative process that can be activated by hypoxia, ultimately resulting in tumor advancement and chemo-resistance. Our study aimed to examine the link between autophagy markers expression in low (LGG) and high-grade gliomas (HGG). In 39 glioma cases, we assessed protein expression of autophagy markers LC3B, p62, and DRAM by immunohistochemistry (IHC) and mRNA expression of autophagy genes; PI3K, AKT, m-TOR, PTEN, ULK1, ULK2, UVRAG, Beclin 1 and VPS34 using RT-qPCR. Livak’s method was used to analyze the relative changes in gene expression and multi-variate Anova test and Spearman's correlation tests were performed for statistical significance. LC3B, p62, and DRAM expression were positive in 64.1%, 51.3%, and 28.2% of glioma cases respectively. The expression of LC3B and p62 was notably higher in HGG compared to LGG. VPS34 exhibited a significant differential expression and increased fold change and demonstrated strong positive correlations with Beclin1 (rs=0.768), UVRAG (rs=0.802), and ULK2 (rs=0.786) in HGG compared to LGG, thus highlighting the potential link between autophagy and glioma progression. We Provide preliminary data for functional analysis of autophagy using cell culture model and to identify potential targets for therapeutic interventions

This research investigates the fatigue crack propagation on the lower surface of rocket deflector troughs of offshore rocket launch platforms. Initially, a numerical model of the offshore rocket launch platform is established using ABAQUS based on the Extended Finite Element Method (XFEM). Subsequently, two variable parameters—namely, the initial crack length and initial tilt angle—are introduced. This research systematically analyzes the impact of these parameters on fatigue crack propagation patterns in both the maximum stress and maximum deformation regions of the deflector channels under the combined conditions of high temperature and impact. Finally, the research indicates that the propagation length of surface cracks in the deflector trough exhibits a trend of initial increase followed by a subsequent decrease with the increase in the preset inclination angle. Notably, the stable propagation rate of the crack in the region of maximum deformation surpasses that observed in the region of maximum stress. Through meticulous comparative analysis, it is evident that temperature loading significantly fosters the initiation and propagation of cracks, particularly in the upper region of the deflector channel's lower surface.

Recent advances in nanomaterials have been heavily influenced by low-dimensional nanocarbon allotropes. In particular, carbyne has attracted attention for its potential as a true one-dimensional carbon chain with sp1 hybridization. To maximize the capabilities of this material, we employ a focused data-driven inverse design approach based on the carbon nanomaterials genome concept. This involves using deep learning neural network models to identify key descriptors tied to desired properties, enabling property prediction and reverse engineering of nanocarbons. Our iterative approach entails: (i) gathering growth/property data on nanostructures; (ii) identifying informative numerical/categorical predictors; (iii) developing deep learning models mapping descriptors to properties; (iv) refining models with new insights; (v) determining required descriptors/conditions for target properties via inverse mapping; (vi) validating models by synthesizing predicted nanostructures; and (vii) enhancing models with validation data. This allows uncovering hidden growth-property connections, precisely tuning nanocarbons for desired attributes. We introduce new methodologies including exciting synergistic effects, synchronizing atomic vibrations, active screen plasma, energy-driven transformations, surface acoustic micro/nano-manipulation, doping and directed self-assembly to expose relationships and integrate insights into the inverse design flow. This research promises to accelerate discovery of next-generation low-dimensional nanocarbons with exceptional properties and applications.

: Low-temperature growth of diamond films by chemical vapor deposition (CVD) method is not so widely reported and especially its initial periods of nucleation and growth phenomenon are of particular interest to the researchers. Four sets of substrates were selected for growing diamond films by linear antenna microwave plasma enhanced CVD (LA-MPCVD). Among them, silicon and sapphire substrates were pre-treated with detonation nanodiamond (DND) seeds before diamond growth for enhancement of its nucleation. On the other hand, carbon nanotube (CNT) films on Si substrates were also used as another template for LA-MPCVD diamond growth. In order to enhance the diamond nucleation during CVD growth, some of the CNT films were again pre-treated by electrophoretic deposition (EPD) of diamond nanoparticles. All these substrates were then put inside the LA-MPCVD chamber for growing diamond films under variable processing conditions. Microwave input powers (1100 – 2800 W), input power modes (pulse or continuous), antenna to stage distances (5 - 6.5 cm), process gas recipes (with or without CO2), methane gas percentages (3 - 5%), deposition times (11 – 120 minutes) were altered to investigate their effect on the growth of diamond film on the pre-treated substrates. The substrate temperatures were found to vary from as low as 170oC to a maximum of 307oC during the alteration of the different processing parameters. Contrary to the conventional MPCVD, it was observed that during the first hour of LA-MPCVD diamond growth, DND seeds or the nucleating structures, do not coalesce together to make a continuous film. Deposition time was the most critical factor in fully covering the substrate surfaces with diamond film, since the substrate temperature could not become stable during the first hour of LA-MPCVD. CNT was found to be oxidised rapidly under LA-MPCVD plasma conditions; therefore, a CO2-free process gas recipe was used to reduce CNT burning. Moreover, EPD-coated CNT was found to be less oxidised by the LACVD plasma during diamond growth.

This work deals with a novel porous TiNi-based material for ophthalmic orbital implants that was produced by high-temperature synthesis (SHS) and possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

Chromium-nickel austenitic stainless steels are widely used due to their high corrosion resistance, good weldability and deformability. To some extent, their application is limited by their mechanical characteristics. As a result of their austenitic structure, increasing the static and dynamic strength of the components can be achieved by surface cold work. Due to the tendency of these steels to undergo intercrystalline corrosion, another approach to improve their mechanical characteristics is the use of low-temperature thermo-chemical diffusion processes. This article proposes a new combined process based on sequentially applied diamond burnishing (DB) and low-temperature gas nitriding (LTGN) to optimally improve the fatigue strength of 304 steel. The essence of the proposed approach is to combine the advantages of the two processes (DB and LTGN) to create a zone of residual compressive stresses in the surface and subsurface layers–the enormous surface residual stresses (axial and hoop) introduced by LTGN, with the significant depth of the compressive zone characteristic of static surface cold working processes. DB (both smoothing and single-pass hardening), in combination with LTGN, achieves a fatigue limit of 600 MPa, an improvement of 36.4% compared to untreated specimens. Individually, smoothing DB, single-pass DB and LTGN achieve 540 MPa, 580 MPa and 580 MPa, respectively. It was found that as the degree of plastic deformation of the surface layer introduced by DB increases, the content of the S-phase in the nitrogen-rich layer formed by LTGN decreases, with resultant increased content of -phase, and a new (also hard) phase: stabilized nitrogen-bearing martensite.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

In the present study, the effect of melatonin and sodium nitroprusside treatments on the improvement of high temperature tolerance in California Wonder green bell pepper plant was studied. For this purpose, a factorial experiment was conducted in a form of a completely randomized design in three replications at Zabol University's Faculty of Agriculture. In this research, green bell pepper plants of Wonder cultivar were exposed to different temperature treatments (25°C, 35°C and 40°C) for 24 hours after being sprayed (foliar application) with 0μM, 50μM and 100μM concentrations of melatonin and sodium nitroprusside. Results showed that Shoot dry weight without fruit (DWPWF) at 40°C in compared to 25°C, 21.54% decreased. Also, foliar application with 100μM melatonin in compared to control (0uM) caused a 13.26% an increased in dry weight of shoots without fruit (DWPWF). Also, leaf chlorophyll at 40°C temperature in compared to 25°C temperature 32.82% decreased and foliar application with 100μM melatonin and 100μM sodium nitroprusside improved leaf chlorophyll value in compared to other foliar application treatments. Foliar application with 50uM and 100uM sodium nitroperoxide at 40°C temperature caused decreased of 15.16% and 20.99% of leaf hydrogen peroxide in compared to 0uM foliar application treatment, respectively. Also, under 40°C temperature, foliar application with melatonin and sodium nitroprusside (50μM and 100μM) in compared to 0μM foliar application activity of leaf superoxide dismutase enzyme increased. Also, leaf nitrogen under with 50 μM and 100μM melatonin in compared to 0μM foliar application 9.61% and 23.72% increased. Leaf potassium in 40°C temperature, foliar application with 50uM melatonin, 100uM melatonin, 50uM sodium nitroprusside and 100μM sodium nitroprusside 55.20, 72, 25.60 and 70.40% in compared to 0uM foliar application increased respectively. leaf iron in foliar application with 100μM sodium nitroprusside in compared to 0μM foliar application 17.96% increased.

To date, radiation adaptation response has been reported as a low-dose related phenomenon and has been associated with radiation hormesis. Well-known cancers are caused by non-radiation active reactants, in addition to radiation. A model of suppression for radiation-specific cancers was previously reported, but the model did not target radiation-nonspecific cancers. In this paper, we describe kinetic models of radiation-induced suppressors for general radiation non-specific cancers, estimating the dose that induces the maximum hormesis effect while satisfying the condition that the risk is approximately proportional to dose above 100 mSv. It was found that the radiation hormesis effect is maximal at about 20 mSv when the rate constant for generation is the same as the rate constant for decomposition. When the two rate constants are different, the dose at which the radiation hormesis effect is maximized depends on both rate constants, but the dose increases as the two rate constants approach each other, reaching a maximum of about 20 mSv. This conclusion may lead to the discovery of unknown cancer suppressors at low doses and the development of cancer suppression methods in the future.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

The identified Urban Heat Island (UHI) phenomenon, coupled with diminished vegetation and anthropogenic heat release, poses a significant environmental challenge for major urban centers. Particularly worrisome is the UHI effect in hot and temperate climates such as the Mediterranean region during the summer season. This exacerbates discomfort and heightens the risks of diseases linked to high temperatures. Additionally, it contributes to environmental consequences, including elevated electricity consumption due to increased demand for cooling [1]. The utilization of Remotely Sensed imagery for estimating Land Surface Temperature has become more prevalent in various applications associated with evaluating urban micro-climates and the Urban Heat Island (UHI) phenomenon. This study presents an algorithm for the automatic mapping of Land Surface Temperature (LST) from Landsat-8 data using a vegetation index-based technique in the Google Earth Engine (GEE) platform. The primary aim is to discern patterns and trends in LST over a 5-year period, from 2017 to 2021. The application was tested in the urban area of Thessaloniki, Northern Greece, which is particularly representative of the Mediterranean urban environment. Computation of Normalized Difference Indices (NDVI, NDBI, NDWI) for the study area was also performed within the GEE platform and correlation analysis was implemented to evaluate the impact of the urban landscape on the distribution of LST.

The transportation sector stands out as California's primary contributor to greenhouse gas emissions, necessitating urgent action from government agencies to promote the adoption of low-carbon transportation (LCT) within the heavy-duty vehicles (HDV) and off-road equipment (ORE) sectors. This study conducts content analysis to delve into the impact of behavioral factors, specifically awareness and impression, on LCT adoption within these sectors. The analysis results are honed using a generative artificial intelligence (AI) tool. Positive associations emerge between the potential for LCT adoption and awareness, as well as factors linked to LCT (government incentives, environmental considerations). Notably, the study reveals that financial barriers and incentives hold greater significance for small-fleet organizations compared to their large-fleet counterparts. These findings offer actionable insights for government agencies to formulate targeted strategies, including mandates and incentives, tailored to the unique needs of organizations within the HDV and ORE sectors.

We will demonstrate how the CMB temperature simply can be predicted from what we will call geometric mean Planck gravitational potential energy in the universe. This falls nicely in line with the recent discovery that the CMB temperature also is a geometric mean of the minimum and maxium temerature in the Hubble sphere, and also that the CMB tem- perature can be derived from the Stefan-Boltzman law. Since the Coulomb force for Planck charges are identical to the Newton force for two Planck mass particles this also seems to give a potential connection between electrostatic force and the CMB temperature.

Dengue is one of the most important arboviruses worldwide, with currently approximately 2.5 billion people at risk of becoming infected, mainly in tropical countries. The present study evaluated the influence of climatic variables on the incidence of dengue fever in an endemic urban area. A time series study of cases was carried out with all confirmed cases of dengue fever in the municipality of Belo Horizonte from 2001 to 2021. The climatic explanatory variables were obtained from the National Institute of Meteorology. The analysis was performed using a generalized linear regression model with three scenarios: a no-lag model, 1-month lag model (1 month earlier) and 2-month lag model (2 months earlier). In the no-lag model, the maximum temperature was associated with an increase in the monthly incidence of dengue (IRR: 1.5). In the 1- and 2-month lag models, the monthly average temperature was associated with an increase in incidence (IRR: 1.9 in both). Our results suggest that temperature contributed to the increase in the incidence of dengue, and an increase of 1 °C could increase the incidence of the disease by approximately 90%. Thus, temperature monitoring can direct efforts towards prevention and control of the disease.

forging a resilient path towards a low carbon future, this research delves deep into the intricate dynamics of the petroleum and petrochemical industries. By uncovering the challenges posed by transitioning to a low carbon economy, this study emphasizes their transformative potential as catalysts for growth. Through an in-depth analysis of the oil and natural gas sector, it not only sheds light on the carbon footprint of Nigeria's petroleum and petrochemical industries but also identifies the opportunities for sustainable transformation within these sectors. Ultimately, this research aims to pave the way for a greener future by unraveling the complexities and intricacies of building a low carbon economy."By incorporating the unique attributes of the petroleum and petrochemical industries and considering the evolving domestic and global context, this research investigates the challenges and prospects associated with the shift towards a low-carbon economy. It delves deep into the complexities of the sector, taking into consideration the distinct characteristics of petroleum and petrochemical production. Through a comprehensive analysis, this study aims to uncover the potential barriers and opportunities that arise from the pursuit of a sustainable and low-carbon future within the petroleum and petrochemical industries. In addition, this research thoroughly examines the current global and local conditions, shedding light on the opportunities for growth and transformation within the petroleum and petrochemical sectors. By presenting insightful perspectives and recommendations, the study aims to provide valuable guidance for fostering the development of a low-carbon economy within these industries. Ultimately, the research seeks to drive positive change by offering actionable insights and strategies to propel the transition towards a sustainable future.

Fresh-cut apple is commonly known as minimally processed agriculture products because of their convenience and ease of consumption. However, during storage, the quality of the apple rapidly changes after the cutting process due to enzymatic and non-enzymatic processes. This study aimed to monitor the quality changes of fresh-cut apples at various temperatures and different types of products in the application of a cold chain system during distribution and storage. The results showed that the total viable count in fresh-cut apples initially differed between apple only and mixed products (apple, orange, and tomato) during storage (p &lt; 0.05). Moreover, there are no significant differences (p &gt; 0.05) in physicochemicals except firmness, titratable acidity, and pH, which are highly correlated to microbial growth (total viable count and total coliform number). Furthermore, the optimal temperature for extending the shelf-life of fresh-cut apples was at 4°C.

Non-alcoholic beer (NAB) or low alcoholic beer (LAB) are taking over the market with a growing sale. Sus-tainable recycling and valorization of exhausted brewer’s spent grains (BSG) coming from craft beer is a relevant issue in brewing process. In this work, recycled BSG and BSG+GJ (supplemented with 10% grape juice) were used as wort-substrate to inoculate already selected non-conventional yeasts to produce NABLAB craft beer. Results showed that wort composed by only recycled BSG produced appreciate NAB beers (ethanol from 0.12% to 0.54 % v/v) while the addition of 10% of grape juice made LAB beers (ethanol from 0.82 to 1.66 % v/v). As expected, volatile compounds production was highest with the addition of grape juice. Lachancea thermotolerans confirmed the lactic acid production and, as Saccharomyces cerevisiae, is characterized by (in both worts) ethyl butyrate and isoamyl acetate, while Torulaspora delbrueckii produced relevant amounts of exanol, phenylethyl acetate and β-phenyl ethanol (wort added with grape juice). Wickeramhomyces anomalus and Pichia kluyvery showed consistent volatile production but only in wort with grape juice addition where a fermentation activity was exhibited. The overall results indicated that reused BSGs, non-conventional yeasts and grape juice is a suitable strategy for specialty NABLAB beer.

Global climate change has induced a rise in sea surface temperature (SST), although this increase is not uniform across the world. Significant variations exist between coastal and offshore waters, particularly in regions affected by upwelling processes. This study focuses on the Canary Current Upwelling System (CCUS), stretching from Northwest Iberia to Northwest Africa. High-resolution remotely sensed SST data (0.05°) from the ODYSSEA Level 4 Sea Surface Temperature Reprocessed dataset were validated with in-situ measurements and employed to establish a regional climatological baseline for 1982 – 2012. Subsequent years were compared to this baseline to construct SST anomaly maps, revealing SST changes since 2012. The study area was further divided into sub-regions for comparative analysis. Results indicate that SST consistently increased at a higher rate offshore compared to the adjacent nearshore regions. A reference dataset spanning 1951 – 1981 was used to gauge SST variability between the two baselines. SST exhibited a 0.59°C increase from 1951 – 1981 to 1982 – 2012, with a slowing of SST trends beyond the 1982 – 2012 baseline. This research offers valuable insights into the climatological dynamics of the CCUS. These findings enhance our understanding of this critical coastal system's climatology, laying the groundwork for future investigations into evolving climate patterns in coastal regions.

Computed tomography (CT) is a widely employed imaging modality with diverse clinical applications in pediatric and adult populations, offering numerous advantages. Despite several alternatives to imaging modalities with ionising radiation, CT scans have demonstrated persistent global popularity, contributing to a substantial amount of effective radiation doses for patients. This exposure results in hazards, including stochastic effects that amplify the radiation-induced cancer risk proportionally to the radiation dose received. CT-related radiation comprises a substantial portion of cumulative effective doses within diagnostic radiology, specifically impacting younger patient cohorts undergoing repeated investigations for chronic diseases over time. Scientific literature over recent decades has explored various methods to mitigate radiation doses during medical imaging. One notable strategy involves implementing low-dose and ultralow-dose CT protocols, maintaining diagnostic efficacy in acute and non-acute medical and surgical conditions. Utilising innovative image reconstruction algorithms, such as iterative reconstruction and emerging deep-learning algorithms based on artificial intelligence, plays a pivotal role in achieving an approximately 80% reduction in patient radiation compared to standard doses. This review article discusses the significance of low-dose protocols across a spectrum of acute and chronic medical conditions affecting different body systems.

A typical solid-state quantum sensor can be developed based on negatively charged nitrogen-vacancy (NV-) centers in diamond. The electron spin state of NV- can be controlled and read at room temperature. Through optical detection magnetic resonance (ODMR) technology, temperature measurement inside living cells can be achieved at the nanoscale. The key to ODMR technology is to apply microwave resonance to manipulate the electron spin state of NV-. Therefore, the microwave field characteristics formed near the NV- have a crucial impact on the sensitivity of ODMR measurement. This article mainly focuses on the temperature situation in cellular applications, and simulates the influence of structural parameters of double open loop resonant (DOLR) microwave antennas and broadband large-area (BLA) microwave antennas on the microwave field’s resonance frequency, quality factor Q, magnetic field strength, uniformity, etc. The parameters are optimized to have sufficient bandwidth, high signal-to-noise ratio, low power loss, and high magnetic field strength in the temperature range of 36 ℃ to 42.5 ℃. Finally, the ODMR spectra are used for effect comparison, and the signal-to-noise ratio and Q values of the ODMR spectra are compared when using different antennas. We have provided an optimization method for the design of microwave antennas and it is concluded that the DOLR microwave antenna is more suitable for living cell temperature measurement in our study.

This article couples human metabolic factors and heating environmental factors, and uses a 57 node human thermal physiological model to study the heating effect of radiators. It provides a way to objectively calculate and directly quantify the effect of heating equipment on human thermal physiological parameters. As the inlet speed increases, the surface temperature of the human body first increases and then decreases. At a speed of 3m/s, it basically reaches a high value. Continuing to increase the wind speed, as the indoor convection intensity further increases, the surface temperature of the human body will decrease, leading to a decrease in thermal comfort. Compared with floor radiation heating under similar indoor temperature conditions, forced convection radiator heating has similar skin temperatures in various parts of the human body after the indoor design temperature exceeds 20 ℃, and the overall thermal comfort of the two technical solutions is equivalent. Research has shown that the turbulence wind speed of convective radiators should not be too small, with a wind speed range of 2.5m/s to 3m/s. The heating effect of using horizontal air outlet from the lower part of the radiator is better than that of vertical air outlet from the upper part. Convection type radiator heating is more suitable for buildings with rooms that are not too high due to the large indoor temperature gradient.

Human epidermal growth factor receptor 2 (HER2) belongs to the ErbB family, a group of four transmembrane glycoproteins with tyrosine kinase activity, all structurally related to the epidermal growth factor receptor (EGFR). These tyrosine kinases are involved in the transmission of cellular signals controlling normal cell growth and differentiation. If this transmission goes awry, it can lead to dysregulated growth of the cell. HER2 specifically can be implicated in the pathogenesis of at least eight malignancies. HER2 positivity quickly became a well characterized indicator of aggressiveness and poor prognosis, with high rates of disease progression and mortality. After realizing the implication of HER2, it first became investigated as a target for treatment in breast cancer, and later expanded to areas of research in other cancers types. To this day, the most therapeutic advancements of anti-HER2 therapy have been in breast cancer, however, there have been strong advancements made in the incorporation of anti HER2 therapy in other cancer types as well. This comprehensive review dissects HER2 to its core incorporating the most up to date information. The topics touched upon are discussed in detail and up to 200 published sources from the most highly recognized journals have been integrated. The importance of knowing about HER2 is exemplified by the groundbreaking advancements that have been made, and the change in treatment plans it has brought to the oncological world in the last twenty years. Since, its ground breaking discovery there has been significant breakthroughs in knowledge regarding the actual receptor, the receptors biology, its mechanism of action, advancements in tests to detect HER2 and significant strides on how to best incorporate targeted treatment. Due to the success of this field thus far, the review concludes by discussing the future of novel anti-HER2 therapy currently in development that everyone should be aware of.

We discuss how the interaction of electrons with an overdamped optical phonon can give rise to a strange-metal behavior over extended temperature and frequency ranges. Although the mode has a finite frequency, an increasing damping shifts spectral weight to progressively lower energies so that, despite the ultimate Fermi liquid character of the system at the lowest temperatures and frequencies, the transport and optical properties of the electron system mimic a marginal Fermi liquid behavior. Within this shrinking Fermi liquid scenario, we extensively investigate the electron self-energy in all frequency and temperature ranges, emphasizing similarities and differences with respect to the marginal Fermi liquid scenario.

To investigate the structural behavior of simply supported concrete beams with steel and polypropylene fiber under low velocity impact loading. In all twenty-four beams (150X200X1800 mm) with simply supported boundary condition were modeled and analyzed using ABAQUS software. Steel and polypropylene fibers of aspect ratio of 60 and 231 respectively are used. The total volumes of fibers are maintained at 1% by volume of specimen. A 100 kg hammer with tip diameter 16 mm (hemispherical contact area = 201 mm2) with four different velocities (3.13 m/s, 4.42 m/s, 5.43 m/s and 6.11 m/s) were used in the analysis. It is observed that with the addition of hybrid fibers the deflection in beams was reduced. The beams with 1% PP and 0% steel fiber shows the maximum deflection values due to low modulus of elasticity. Beams with 0.9% steel and 0.1% polypropylene fibers was less affected in terms of deflection as compared to all other beams, it is due to presence of high tensile strength fibers.

C-peptide is used as a measure of endogenous insulin production. Given that insulin and C-peptide are produced in equal amounts, C-peptide is typically used to differentiate between external and endogenously produced insulin in insulin-treated type 1 diabetes mellitus (T1DM). In a clinical setting, a decline in C-peptide is regarded as a loss of beta cell function. However, physiological conditions may also be associated with low C-peptide levels. The authors of this paper use a low-carbohydrate diet, the so-called paleolithic ketogenic diet (PKD), in the treatment of various conditions and observed that C-peptide is typically low on this diet. In order to characterize C-peptide levels on this diet, we designed a study to retrospectively assess C-peptide levels in 100 non-T1DM subjects. We found that 55% of the subjects had a C-peptide level below the standard reference range. C-peptide levels correlated with glucose levels. A significant correlation was found between C-peptide and age, with younger subjects having lower C-peptide levels. Males also showed lower C-peptide levels than females. Given the increasing number of patients using low-carbohydrate diets worldwide, physicians should be aware of laboratory correlates of low-carbohydrate diets, including low C-peptide levels, most importantly to prevent incorrect T1DM diagnosis.

In the present study, the effect of melatonin and sodium nitroprusside treatments on the improvement of high temperature tolerance in California Wonder green bell pepper plant was studied. For this purpose, a factorial experiment was conducted in form of a completely randomized design in three replications at Zabol University's Faculty of Agriculture. In this research, green bell pepper plants of Wonder cultivar were exposed to different temperature treatments (25°C, 35°C and 40°C) for 24 hours after being sprayed (foliar application) with 0μM, 50μM and 100μM concentrations of melatonin and Sodium nitroprusside. Results showed that Instantaneous leaf water consumption efficiency in 40°C temperature treatment with 50μM and 100μM melatonin increased. Also in 40°C temperature with 100µM melatonin, fruit dry weight in compared to control (0uM) 13.15% increased. Also, melatonin and sodium nitroprusside treatments in compared to control treatment improved fruit characteristics and reduced Appearance Characteristics of Fruit Marketability (ACFM) number. Under 40°C temperature treatment in compared to control temperature (25°C), fruit total soluble solids (TSS) 18.50% decreased also under 100μM melatonin treatment, fruit TSS 20.69% was increased compared to control treatment (0μM). Also fruit fructose at 40°C temperature in compared to 25°C temperature treatment 5.52% reduced. Fruit calcium at 35°C and 40°C temperature in compared to control temperature 6.96% and 15.65% decreased respectively. At temperature 35°C under foliar application of 100uM sodium nitroprusside, fruit copper in compared to control 28.93% increased.

Smart farm is a technology that greatly helps improve the productivity and quality of crops and is being actively introduced into indoor environments such as green houses. However, it has not yet been distributed to field-grown crops. The main reason is that, unlike indoor environments, it is very difficult to collect sensor data for monitoring the growth environment of crops in open fields where weather conditions change significantly and power supply is difficult. Additionally, because various sensors are used, the data formats of the devices are different, making it difficult to process. This paper presents a field crop growth environment monitoring and big data analysis system. The proposed system first solves power supply and data communication problems using solar power generation and LPWA technology. Additionally, based on the oneM2M architecture, data from various sensors is transmitted to the server using standardized technology. The transmitted data is stored and managed on the server as big data, and can be used to predict the production and quality of field-grown crops and take appropriate measures. The proposed system is expected to create an environment optimized for the growth of field crops and help prevent and manage diseases.

Studies at the juncture of development economics and public health host considerable responsibility in addressing inequality and related mental health distress. Mental health care in economically marginalized populations requires depicting the linkages between socioeconomic status and psychological distress. In the present work, a sequential mixed-methods design was used to study 190 people in such communities in India. Gender-dependent psychological distress was found according to Kessler Psychological Distress Scale (K-10) with moderate distress in women (M= 26.30, SD= 9.15) and mild distress in men (M= 21.04, SD= 8.35). Regression analysis indicated that gender significantly predicted psychological distress, followed by age, marital status, and education of the head of the family. The Interpretative Phenomenological Analysis of semi-structured interviews to six women who scored the highest on the distress scale unveiled three master themes: (1) Manifestation of Psychological Distress, (2) Contextual Challenges, and (3) Sources of Strength and Resilience. Overall, participants reported lack of resources, community violence, gender discrimination, and widespread substance use as major contributors to the ongoing distress. These findings can pave the way for future studies to expand beyond independent economic indicators and curate clinical interventions for culturally competent mental health care.

This paper presents the design and measurement of an IEEE 802.11ad standard compatible RF transceiver for 60GHz wireless communication system. In addition to the traditional half-duplex (HD) mode, this work supports full-duplex (FD) operation to deliver better channel utilization and faster response time for the system. The isolation between the transmitter and receiver from the architecture design to system integration for FD operation has been fully considered. A digital self-interference cancellation (DSIC) is implemented in MATLAB to verify the FD performance. The super-heterodyne architecture with an intermediate frequency (IF) of 12GHz is designed to suppress the image frequencies without using extra filters. A flexible phase-locked loop (PLL) synthesizer provides a local oscillator (LO) frequency with a 2kHz resolution. Other than the time division duplex (TDD) mode used in the conventional 60GHz system, a wide bandwidth baseband digital variable gain amplifier (DVGA) with a 3dB bandwidth of more than 4GHz also supports frequency division duplex (FDD) operation. The transceiver chip is fabricated in Tower Jazz 0.18µm SiGe BiCMOS process. With on-board antenna, the transceiver covers all four channels in 802.11ad standard with MCS-12 (7.04Gbps under 1.76GSym/s and 16-QAM) under 1.5m. In the proposed system design, the RF frontend based self-interference (SI) suppression from the local transmitter to receiver LNA is around 54dB. To achieve a practical FD application, the SI is further suppressed with the help of digital SI compensation. The measured power consumption for transmitter and receiver configuration is 194mW and 231mW, respectively, in HD mode and 398mW for FDD or FD operation mode.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

Surface processes such as coatings, corrosion, photocatalysis, and tribology are greatly diversified by acid-base interaction at the surface overlayer. This study focuses on the action of metallic copper surface as an electron donor/acceptor related to inactivation of viruses; it was found that regarding Cu2O or Cu materials electrostatic interaction plays a major role in virus inactivation. We applied TPPE method to clarify the mechanism of electron transfer (ET) occurring at light irradiated copper surfaces. The TPPE characteristics was strongly influenced by the environments, which correspond to the temperature and environment dependence of the total count of emitted electrons in the incident light wavelength scan (PE total count, NT), the photothreshold, and further the activation energy (E) analyzed from Arrhenius plot of NT values obtained in the temperature-increase and subsequent temperature-decrease processes. In this study we reexamined the dependence of the TPPE data from two types of Cu metal surfaces: Sample A, which was mechanically abraded in alcohols, water, and air, and Sample C, which was only ultrasonically cleaned in these liquids. The NT for both Samples slowly increased with increasing temperature, reached a maximum (NTmax) at 250C (maximum temperature, Tmax), and after that decreased. For Sample A the NTmax value decreased in the order H2O > CH3OH > C2H5OH > (CH3)2CHOH > C3H7OH, although the last alcohol gave Tmax = 100C, while with Sample C the NTmax value decreased in the order: C3H7OH > (CH3)2CHOH > C2H5OH > CH3OH > H2O. Interestingly, both orders of the liquids were completely opposite: this means that Cu surface can possess two-way character. The NT intensity was found to be strongly associated with the change of the hydroxyl group (Cu-OH) to the oxide oxygen (O2) in the O1s spectra in the XPS measurement. The difference between the above orders was explained by the acid-base interaction mode of the Cu-OH group with the adsorbed molecule on the surfaces. The H2O adsorbed on Sample A produces the electric dipole Cu-OH+---:OH2 (--- hydrogen bond), while the C3H7OH and (CH3)2CHOH adsorbed on Sample C produce ROH+---:O(H)-Cu (R = alkyl groups). Gutmann’s acceptor number (AN) representing the basicity of the liquid molecules was found to be related to the TPPE characteristics: (CH3)2CHOH (33.5), C2H5OH (37.1), CH3OH (41.3), H2O (54.8) (the AN of C3H7OH could not be confirmed). With Sample A the values of NTmaxa and EaUp1 both increased with increasing AN (Up1 means the 1st temperature-increase process). On the other hand, with Sample C the values of NTmaxc and EcUp1 both decreased with increasing AN. These findings suggest that Sample A acts as an acid, while Sample C functions as a base. However, in the case of both types of Samples A and C the NTmax values were found to increase with increasing EUp1. It was explained that the EUp1 values depending on the liquids originate from the difference in the energy level of the hydroxyl group radical at the surface denoted. This is able to attract electrons in the neighborhood of the Fermi level of the base metal by tunnelling. After that due to Auger emission electrons are released, leading to the ET in the overlayer. These electrons are considered to have a strong ability of reducibility.

Phenylketonuria is an inherited metabolic disorder that leads to neurobehavioral dysfunction. The main treatment is a low-phenylalanine diet and/or the cofactor tetrahydrobiopterin. Regular outpatient follow-up care and measurement of the phenylalanine level in the blood are required. We aimed to analyze the economic burden of phenylketonuria on families and the state. The pa-tients with phenylketonuria were divided into three groups according to their treatment: a low-phenylalanine diet group (n= 50), a tetrahydrobiopterin group (n= 44) and a group taking tetra-hydrobiopterin together with the diet (n= 25). A comparative cost analysis was carried out. The annual economic burden to the state was calculated to average €18801±15345 and was lowest in the diet group, then in the tetrahydrobiopterin group and highest in the tetrahydrobiopterin+diet group (p < 0.001). Out-of-pocket costs amounted to €1531±1173 per year, and indirect losses aver-aged €2125±1930 per year for all families. The economic loss was significantly lower in the fami-lies taking tetrahydrobiopterin than in the other groups (p=0.001). The combined use of medical nutrition and BH4 treatments has been shown to increase the economic harm to the state. Reim-bursing low-protein products and increasing the rate of patients eligible for financial allowances may reduce the economic harm to families.

The regions with the best economy have a greater capacity to develop low-income or social impact housing, thus contributing to the reduction of poverty, and therefore, to the fulfillment of the Sustainable Development Goals. This is observed in fewer people living in extreme poverty and with fewer unmet basic needs. The present article analyzes the correlation between development by the main economic sectors in the different regions (departments) of Colombia, and the offer of low-income housing. The valid relationship found is between the economic condition of the regions (GDP) and non-social housing (more expensive commercial value) (Spearman´s Rho: 0.9). That means that there is an imbalance between regional economic capacity and the low-income housing offer because their economic potential allows them to have less of a demanding population, that is, living in poverty. This correlation is higher with activities that are mostly developed in an urban environment, such as manufacturing, construction, real estate, and finance and insurance. On the contrary, the correlation is lower with industries such as mining and agriculture, which mostly operate in rural areas. The analysis for low-income housing and economic sectors GDP yields low correlations, but are especially dismissible for more rural industries, such as mining and agriculture. The analysis shows the change of trend in the correlations for the year 2021, the beginning of the post-pandemic economic recovery.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

This study leverages the relationships between the Great Plains low-level jet (GP-LLJ) and the circumglobal teleconnection (CGT) to enhance the 30-day rainfall forecast skill in the Northern Great Plains (NGP). The assessment of 30-day simulated precipitation using the Climate Forecast System (CFS) is contrasted with the North American Regional Reanalysis, searching for sources of precipitation predictability associated with extended wet and drought events. We analyze the 30-day sources of precipitation predictability using (1) the characterization of dominant statistical modes of variability of 900-mb winds associated with the GP-LLJ, (2) the large-scale atmospheric patterns based on 200-mb geopotential height (HGT), and (3) the use of GP-LLJ and CGT conditional probability distributions using a continuous correlation threshold approach to identify when and where the forecast of NGP precipitation occurs. Two factors contributing to the predictability of precipitation in the NGP are documented. We found that multi-scale geospatial interactions occur at the daily and sub-seasonal time windows. The CFS reforecast suggests that the ability to forecast sub-seasonal precipitation increases in response to the enhanced simulation of the GP-LLJ and CGT. Finally, the multi-dimensional analysis of covariance reveals that high-precipitation forecasting skill is associated with a better prognostic of GP-LLJ and CGT.

In recent decades, there have been significant problems worldwide related to global warming and the intensification of extreme temperature and rainfall events. This research evaluated daily temperature and rainfall indices trends to identify whether warming signals have occurred in South Australia over the past fifty years. Extreme cold, hot, and rainfall events were calculated using climatic data from 37 weather stations. A Mann-Kendall test was used for trend analysis with Sen's estimator. As a result, we determined that for the 1970-2021 period, the maximum and minimum temperatures increased by 1.1 and 0.7 °C, respectively, while precipitation had a negative trend (-52.2 mm/period). Since statistical significance was found in analysing extreme cold and hot events, we find that warming signals have several impacts on South Australia. In the case of rainfall events, we identified a heterogeneous pattern characterised by a reduction in the annual amount, and an increase in extreme rainfall events. The findings enable us to conclude that the area shows signs of global warming that could affect the intensity and magnitude of droughts. This information is essential for continuing with current management strategies to adapt and mitigate the effects of global warming in South Australia.

The various methods used to choose the profile shift coefficients, primarily the so-called equalizations, were based on assumed advantages without physical evidence proving them. In this paper a new calculation method is presented for determining profile shift coefficient. The procedure gives the pair of values ​​of the profile shift coefficients, in which case, under the given load, the resulting bending stress will be of the lowest possible value.

Coral reefs are one of the most productive yet vulnerable ecosystems on Earth. An important step in understanding the functioning of coral communities is studying the environmental impact on the state of reefs. The present study aimed to assess the impacts of the water temperature, precipitation, wave action and population density on the seasonal bleaching, partial and complete mortality of shallow-water branching corals of Pocillopora verrucosa species complex. The present study was conducted at the Dam Bay research station (Nha Trang Bay) from 26 April 2020 to 2 April 2021. Throughout the study the percentage of bleached coral colonies varied from 1 to 41.5% with two peaks, in autumn (October) and spring (April). Rates of the development of partial mortality varied from 0 to 10%, with a pronounced peak in December. At the end of the experiment, the percentage of coral colonies suffering from partial mortality reached 47%. Only 4,5% of experimental colonies died by the end of the study. Analysis revealed that water temperature and partial mortality are the drivers of bleaching, while wave action, temperature and bleaching are the factors with a significant impact on partial mortality. In the present study, the main cause of coral death was the development of algal fouling at the sites of colony lesions, which gradually spread over the entire surface of the colony. We showed also that the impact of individual stress on mortality prevailed over the impact of seasonal bleaching and partial mortality events.