Zinc protection of galvanized steel is initially dissolved in alkaline solutions. However, passive layer is formed over time which protects the steel from corrosion. The behavior of galvanized steel exposed to strong alkaline solutions (pH values of 12.7) with a fixed concentration of sulfate ion of 0.04M is studied. Electrochemical measurement techniques such as corrosion potential, linear polarization resistance and electrochemical impedance spectroscopy are used. Synergistic effect of sulfate ion is also studied together with other anions such as chloride Cl- or bicarbonate ion HCO3- and with other cations such as calcium Ca2+, ammonium NH4+ and magnesium Mg2+. Presence of sulfate ions can depassivate the steel, leading to corrosion density of 0.3 µA/cm2 at the end of the test. The presence of other ions in the solution increases this effect. The increase in corrosion density caused by cations and anions responds to the following order (greater to lesser influence): NH4+>Ca2+>Mg2+ and HCO3- >Cl- >SO42-.

Regression models are mostly used in all fields of sciences for modelling the relationship between a dependent variable and independent variable(s). The least square method is often used to estimate the parameters in a linear model because it is the best linear unbiased estimator. These estimates can only be reliable if the assumption of normality is satisfied. In some cases the dependent variable might be bimodal and shows a non-linear relationship with the independent variable(s). In this case, a non-linear model should be used. In non-linear model, the standard errors are often obtained by linearizing the nonlinear function around the parameter, assuming central limit theorem. After the linearization, the least square parameter estimates are obtained. It should be noted that the error of the non-linear model is different from that of the transformed linear model. Thus, there is a need to transform back to the original non-linear model. In this note, a novel non-linear function was developed into a non-linear regression model, called Normal-Power model. The least square method was used to estimate the parameter of the transformed model. Its usefulness in regression model was demonstrated using real data of Nigeria Economy-Tourism model.

In surveying engineering tasks, close-range photogrammetry belongs to leading technology considering different aspects like the achievable accuracy, availability of hardware and software, accessibility to measured objects, or the economy. Hence, constant studies on photogrammetric data processing are desirable. Especially in industrial applications, the control points for close-range photogrammetry are usually measured using total stations. In the case of small objects, more precise positions of control points can be obtained by deploying and adjusting a three-dimensional linear network set up on the object. The article analyzes the accuracy of the proposed method, based on the measurement of the linear network using a tape with a precision of ±1 mm. The experiment shows that the adjusted positions of the network control points can be determined with high, one-millimeter accuracy. The photogrammetric 3D model derived referring to such control points and stereo-images captured with a non-metric camera is also characterized by the highest possible precision, which qualifies the presented method to accurate measurements used in surveying engineering. The authors prove that the distance between two randomly optional points derived from the 3D model of a dimensioned object is equal to the actual distance measured directly on it with one-millimeter accuracy.

Solving Linear equations with large number of variable contains many computations to be performed either iteratively or recursively. Thus it consumes more time when implemented in a sequential manner. There are many ways to solve the linear equations such as Gaussian elimination, Cholesky factorization, LU factorization, QR factorization. But even these methods when implemented on a sequential platform yield slower results as compared to a parallel platform where the time consumption is reduced considerably due to concurrent execution of instructions. The above mentioned linear equation solving methods can be implemented on the parallel platform using the direct approaches such as pipelining or 1D and 2D Partitioning approach. Vedic mathematics is a very ancient approach for solving mathematical problems. These Vedic mathematical approaches are well known for quicker and faster computation of mathematical problems. Vedic Mathematics provides a very different outlook towards the approach of solving linear Equation on parallel platform. It could be considered as a better approach for reducing space consumption and minimizing the number of algebraic operations involved in solving linear equation. In future Vedic Mathematics might serve as a viable solution for solving linear equation on parallel platform.

Recently, most countries suffering from global warming due to the waste gases coming out of the combustion engines used to generate electric power by traditional methods. Therefore, many countries are currently trying to find alternative solutions to this problem by using renewable energies such as solar energy, wind energy, and energy generated from the waves of the ocean and sea to overcome pollution problems. The waves of the seas and oceans have enormous and largely untapped energy, so this work presents an efficient way to use the energy of sea waves to generate electricity. And also, trying to be a way to produce electricity from wave energy in the future. The best suitable places along the shores of Jizan city were inspected to install the buoy system to revenue advantage of the wave supreme height to achieve the height amount of electrical energy. A mathematical model was made to analyze the wave energy and convert it into energy extracted by mechanical force. The mathematical analyzes used the data collected from satellite maps of the numerous severe waves in the Red sea of the Jazan area, and the data published in previous research along that area. It was found that the beach of the Al Shuqaiq area is the greatest for installing the buoy and obtaining the highest electrical energy due to the presence of the highest wave intensity, followed by the beach of the Baysh and Al Morgan area. Also, one of the objectives of this research is to study the design of a device powered by a buoy to use the waves of the Red Sea to generate electric power. The influence of the buoy system design parameters such as the buoy diameter, length of the cylinder, and the length of the connecting rod on the electrical energy generation from wave energy was investigated. The current device is designed with a gearbox to produce continuous power with a single electric generator. A floating mooring device uses the rise and fall of bulges to convert sea wave energy into electrical energy. The device consists of a float, arm, two wheels of different diameters, a gear set, and an electric generator. The effect of the design of several factors on the performance of the device for converting the sea waves energy into electrical energy, including the length of the buoy arm, the wave height by changing the cam diameter, and the conversion ratios between the gear set, to optimize the output power of the wave energy.

Temperature dependent entropic force acting between the straight direct current I and the linear system (string with length of L) of N elementary non-interacting magnets/spins μ is reported. The system of elementary magnets is supposed to be in the thermal equilibrium with the infinite thermal bath T. The entropic force at large distance from the current is given by Fmagnen=Nμ02μ2I24π2kBTr3 , where r is the distance between the edge of the string and the current I, and kB is the Boltzmann constant; (r≫L is adopted). The entropic magnetic force is the repulsion force. The entropic magnetic force scales as Fmagnen~1T , which is unusual for entropic forces. The effect of “entropic pressure” is predicted for the situation when the source of the magnetic field is embedded into the continuous media, comprising elementary magnets/spins.

Autonomous navigation of spacecraft necessitates innovative technologies, methods, and algorithms, particularly when orbiting in proximity of other space objects. Optimization methods are useful for autonomous spacecraft navigation, guidance, and control, but their performance is hampered by noisy multi-sensor technologies and poorly modeled system equations, and real-time on-board utilization is generally computationally burdensome. Some proposed methods use noisy sensor data to learn the optimal guidance and control solutions real-time (online), where non-iterative instantiations are preferred to reduce computational burdens. This study aims to highlight efficacy and limitations of several common methods for optimizing guidance and control while proposing a few more, where all methods are applied to the full, nonlinear, coupled equations of motion including cross-products of motion from the transport theorem. Five disparate types of optimum guidance and control algorithms are presented and compared to a classical benchmark. Comparative analysis is based on tracking errors (both states and rates), fuel usage, and computational burden. Real-time optimalization with singular switching plus nonlinear transport theorem decoupling proves superior by matching open-loop solutions to the constrained optimization problem (in terms of state and rate errors and fuel usage), while robustness is validated in the utilization of mixed, noisy state and rate sensors and uniformly varying mass and mass moments of inertia. State tracking errors are reduced one-hundred ten percent. Rate tracking errors are reduced one-hundred thirteen percent. Control utilization (e.g., fuel) is reduced eighty four percent, while computational burden in reduced ten percent simultaneously.

Training supervised machine learning models requires labeled examples. A judicious choice of examples is helpful when there is a significant cost associated with assigning labels. This article improves upon a promising extant method – Batch-mode Expected Model Change Maximization (B-EMCM) method – for selecting examples to be labeled for regression problems. Specifically, it develops and evaluates alternate strategies for adaptively selecting batch size in B-EMCM. By determining the cumulative error that occurs from the estimation of the stochastic gradient descent, a stop criteria for each iteration of the batch can be specified to ensure that selected candidates are the most beneficial to model learning. This new methodology is compared to B-EMCM via mean absolute error and root mean square error over ten iterations benchmarked against machine learning data sets. Using multiple data sets and metrics across all methods, one variation of AB-EMCM, the max bound of the accumulated error (AB-EMCM Max), showed the best results for an adaptive batch approach. It achieved better root mean squared error (RMSE) and mean absolute error (MAE) than the other adaptive and non-adaptive batch methods while reaching the result in nearly the same number of iterations as the non-adaptive batch methods.

Damage detection based on modal parameter changes becomes popular in the last decades. Nowadays are available robust and reliable mathematical relations to predict the natural frequency changes if damage parameters are known. Using these relations, it is possible to create databases containing a large variety of damage scenarios. Damage can be thus assessed by applying an inverse method. The problem is the complexity of the database, especially for structures with more cracks. In this paper, we propose two machine learning methods, namely the random forest (RF) and the artificial neural network (ANN) as search tools. The databases we developed contain damage scenarios for a prismatic cantilever beam with one crack and ideal and non-ideal boundary conditions. The crack assessment is made in two steps. First, a coarse damage location is found from the networks trained for scenarios comprising the whole beam. Afterward, the assessment is made involving a particular network trained for the segment of the beam on which the crack is previously found. Using the two machine learning methods, we succeed to estimate the crack location and severity with high accuracy for both simulation and laboratory experiments. Regarding the location of the crack, which is the main goal of the practitioners, the errors are less than 0.6%. Based on these achievements, we concluded that the damage assessment we propose, in conjunction with the machine learning methods, is robust and reliable.

This paper will discuss the application of statistic modeling to interpret a health system crisis in Sri Lanka due to COVID- 19.A strong focus on the preventive approach and the contact tracing with the utilization of available resources in a rational manner describes Sri Lanka’s response towards COVID- 19 prevention and mitigation. The early contact tracing, preemptive quarantining, isolation, and treatment were implemented as a concerted effort. This approach, proven efficient during the early phase of the pandemic, was sustainable when there was a rapid increase in the COVID- 19 patients since July 2021, exceeding the health system capacity.The country’s COVID- 19 situation during the period from 01st of August 2021 to 31st of October 2021 was taken into consideration. Variables used for analysis were; total number of cases, recovered cases, comorbid and O₂ dependent patients, ICU patients, and deaths. The regression model was applied to analyze the data by using the EViews 12 (x64) software application.The correlation coefficients of all the independent variables under consideration implies that they have a strong positive relationship with the number of deaths occurred during the said period. According to the computed multiple linear regression model, the number of positive cases and O₂ dependents have a positive relationship with the dependent variable. Further, the Durbin- Watson stat value of the model and multicollinearity test reflect that it is free from serial correlation thereby the model is fit. From the perspective of epidemiological control, these findings highlight the importance of keeping the number of cases within the limits of health system capacity.

This paper investigates the meaning of a specific intonation contour found in the Northern Australian language Iwaidja called Linear Lengthening Intonation (LLI). Using an experimental field work approach, we analysed approximately 4,000 utterances. We demonstrate that the semantics of LLI is broadly event-quantificational as well as temporally scalar. LLI imposes aspectual selectional restrictions on the verbs it combines with (they must be durative, i.e. cannot describe ‘punctual’, atomic events), and requires the event description effected by said verbs to exceed a contextually-determined relative scalar meaning (e.g., a ‘typical duration’ à la (Tatevosov 2008)). Iwaidja differs from other Northern Australian languages with similar intonation patterns (see e.g. (Bishop 2002: 2002; Simard 2013)), in that it does not seem to have any argument NP-related incremental or event scalar meaning. This suggests that LLI is a decidedly grammatical, language-specific device; not a purely iconic kind of expression (even though it also possibly has an iconic dimension).

This work presents a control scheme to control the grid-connected single-phase photovoltaic (PV) system. The considered system has four 250W solar panels, a non-inverting buck-boost DC-DC converter, and DC-AC inverter with LCL filter. The control system aims to track and operate at the maximum power point (MPP) of PV panels, regulate the voltage of DC link, and supply the grid with a unity power factor. To well achieve these goals, the proposed control system consists of three parts, that are MPP tracking controller module with a fuzzy-based modified incremental conductance (INC) algorithm, a DC-link voltage regulator with a hybrid fuzzy proportional-integral (PI) controller, and a Current Controller module using the linear quadratic regulator (LQR) for grid-connected power. Based on fuzzy control and LQR, this work introduces a full control solution for grid-connected single-phase PV systems. The key novelty of this research is to analyze and prove that the newly proposed method is more successful in numerous aspects by comparing and evaluating the previous and present control methods. The designed control system settles quickly, which is critical for output stability. In addition, as compared to backstepping approach used in our past study, the LQR technique is more resistant to sudden changes and disturbances. Furthermore, backstepping method produces the larger overshoot, which has a detrimental impact on efficiency. Simulation findings under various weather conditions were compared to theoretical ones to indicate that the system can deal with variations in weather parameters.

Kinetic parameters of SO2 adsorption on unburned carbons from lignite fly ash and activated carbons based on hard coal dust were determined. The model studies were performed using the linear and non-linear regression method for the following models: pseudo first and second-order, intraparticle diffusion, and chemisorption on a heterogeneous surface. The quality of the fitting of a given model to empirical data was assessed based on: R2, R, Δq, SSE, ARE, χ2, HYBRID, MPSD, EABS, and SNE. It was clearly shown that it is the linear regression that more accurately reflects the behaviour of the adsorption system, which is consistent with the first-order kinetic reaction – for activated carbons (SO2+Ar) or chemisorption on a heterogeneous surface – for unburned carbons (SO2+Ar and SO2+Ar+H2O(g)+O2) and activated carbons (SO2+Ar+H2O(g)+O2). Importantly, usually, each of the approaches (linear/non-linear) indicated a different mechanism of the studied phenomenon. A certain universality of the χ2 and HYBRID functions has been proved, the minimization of which repeatedly led to the lowest SNE values for the indicated models. Fitting data by any of the non-linear equations based on the R or R2 functions only, cannot be treated as evidence/prerequisite of the existence of a given adsorption mechanism.

H-adaptivity is an effective tool to introduce local mesh refinement in FEM-based numerical simulation of crack propagation. The implementation of h-adaptivity could benefit the numerical simulation of fatigue or accidental load scenarios involving large structures such as ship hulls. In engineering applications, the element deletion method is frequently used to represent cracks. However, the element deletion method has some drawbacks such as strong mesh dependency and loss of mass or energy. In order to mitigate this problem, the element splitting method could be applied. In this study, a numerical method called ‘h-adaptive element splitting’ (h-AES) is introduced. The h-AES method is applied in FEM programs by combining h-adaptivity with the element splitting method. Two examples using the h-AES method to simulate cracks in large structures under linear-elastic fracture mechanics scenario are presented. The numerical results are verified against analytical solutions. Based on the examples, the h-AES method is proven to be able to introduce mesh refinement in large-scale numerical models that consist of structured coarse meshes. By employing the mesh refinement introduced in this paper, very small cracks are well represented in large structures.

The fifth Generation (5G) mobile networks use millimeter Waves (mmWaves) to offer giga bit data rates. However, unlike microwaves, mmWave links are prone to user and topographic dynamics. They easily get blocked and end up forming irregular cell patterns for 5G. This in turn cause too early, too late, or wrong handoffs (HOs). To mitigate HO challenges, sustain connectivity and avert unnecessary HO, we propose a HO scheme based on Jump Markov Linear System (JMLS) and Deep Reinforcement Learning (DRL). JMLS is widely known to account for abrupt changes in system dynamics. DRL likewise emerges as an artificial intelligence technique for learning highly dimensional and time-varying behaviors. We combine the two techniques to account for time-varying, abrupt, and irregular changes in mmWave link behaviour by predicting likely deterioration patterns of target links. The prediction is optimized by meta training techniques that also reduces training sample size. Thus, the JMLS-DRL platform formulates intelligent and versatile HO policies for 5G. Results show our proposed prediction scheme about target link behavior post HO to be highly reliable. The scheme also averts unnecessary HOs thus ably supports longer dew time.

Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in a linear stage type test equipment. For this purpose, the causes of position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, the methods of adding balancing weights to the platform unit and adjusting the stiffness of LM Guides are proposed. This reduces the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.

Background: In the functional data analysis (FDA), the hybrid or mixed data are scalar and functional datasets. The semi-functional partial linear regression model (SFPLR) is one of the first semiparametric models for the scalar response with hybrid covariates. Various extensions of this model are explored and summarized. Methods: Two first research articles, including “semi-functional partial linear regression model”, and “Partial functional linear regression” have more than 300 citations in Google Scholar. Finally, only 106 articles remained according to the inclusion and exclusion criteria such as 1) including the published articles in the ISI journals and excluding 2) non-English and 3) preprints, slides, and conference papers. We use the PRISMA standard for systematic review. Results: The articles are categorized into the following main topics: estimation procedures, confidence regions, time series, and panel data, Bayesian, spatial, robust, testing, quantile regression, varying Coefficient Models, Variable Selection, Single-index model, Measurement error, Multiple Functions, Missing values, Rank Method and Others. There are different applications and datasets such as the Tecator dataset, air quality, electricity consumption, and Neuroimaging, among others. Conclusions: SFPLR is one of the most famous regression modeling methods for hybrid data that has a lot of extensions among other models.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

This paper reviews the low-resilience problem in many cities, poor designs of cities to cope with disasters, and the need for tolerance of urban constructions. It explores answers concerning the question of how shall we build cities resiliently? The method of this applied research is a multiphase process that considers all physical and socioeconomic elements of a city. It introduces six indicator groups of urban management (M), economy (E), built environments (U), Infrastructures (I), natural environments (N), and health protection (H). The groups include 55 indicators as variables in the mathematical calculations in this paper. This paper builds a mathematical model to maximize the profitability of resilient buildings by optimizing investments in the required projects. The projects will upgrade the firmness and tolerance of cities against nature-based and human-made dangers and risks. There is a linear programming in 55 variables to select optimal solutions from fifty-five factorial alternatives. Then, the programming will develop into non-linear programming. The unique innovation of this paper is its linear programming interpretation by non-linear to give optimal solutions for the problem. Applying the Lagrange function in the Kuhn-Tucker conditions proves the accuracy of the hypothesis that post-COVID urbanization requires maximum resilience. Only in this way, the urban economies will be free of risks. Outcomes in this paper will assist in the pre-planning, design, and building of built environments everywhere resilient and sustainable.

This addendum contains clarifications and a sharpening of some of the results on the VIT transform framework developed in [1]. The focus is on the right-coefficient and left- coefficient forms of the transform, the extraction of a first-order term from a left polynomial fraction, and the application to linear time-varying systems.

Epidermal growth factor receptor (EGFR) is a receptor tyrosine kinase that instigates several signaling cascades, including the NF-kB signaling pathway, to induce cell differentiation and proliferation. Overexpression and mutations of EGFR are found in up to 30% of solid tumors and correlate with a poor prognosis. Although it is known that EGFR-mediated NF-kB activation is involved in tumor development, the signaling axis is not well elucidated. Here, we found that PKP2 and the LUBAC complex were required for EGFR-mediated NF-kB activation. Upon EGF stimulation, EGFR recruited PKP2 to the plasma membrane, and PKP2 bridged HOIP, the catalytic E3 ubiquitin ligase in the LUBAC, to the EGFR complex. The recruitment activated the LUBAC complex and the linear ubiquitination of NEMO, leading to IkB phosphorylation and subsequent NF-kB activation. Furthermore, EGF-induced linear ubiquitination was critical for tumor cell proliferation and tumor development. Knockout of HOIP impaired EGF-induced NF-kB activity and reduced cell proliferation. HOIP knockout also abrogated the growth of A431 epidermal xenograft tumors in nude mice by more than 70%. More importantly, the HOIP inhibitor, HOIPIN-8, inhibited EGFR-mediated NF-kB activation and cell proliferation of A431, MCF-7, and MDA-MB-231 cancer cells. Overall, our study reveals a novel linear ubiquitination signaling axis of EGFR, and perturbation of HOIP E3 ubiquitin ligase activity is potential targeted cancer therapy.

The Oldroyd–B model for a linear viscoelastic fluid is employed to investigate the buoyant flow in a vertical porous layer with permeable boundaries kept at different uniform temperatures. Seepage flow in the viscoelastic fluid saturated porous layer is modelled through an extended version of Darcy’s law taking into account the Oldroyd–B rheology. The basic stationary flow is parallel to the vertical axis and describes a single–cell vertical pattern where the cell has an infinite vertical height. A linear stability analysis of such a basic flow is carried out to determine the onset conditions for a multicellular pattern. The neutral stability curves and the values of the critical Rayleigh number are evaluated numerically for different retardation time and relaxation time characteristics of the fluid.

In this paper, we consider with a class of system of differential equations whose argument transforms are involution. In this an initial value problem for a differential equation with involution is reduced to an initial value problem for a higher order ordinary differential equation. Than either two initial conditions are necessary for a solution, the equation is then reduced to a boundary value problem for a higher order ODE.

We present a method to turn results of model-based optimisations into resilient and comprehensible control strategies. Our approach is to define priority lists for all available technologies in a district energy system. Using linear discriminant analysis and the results of the optimisations, these are then assigned to discrete time steps using a set of possible steering parameters. In contrast to the model-based optimisations, the deduced control strategies do not need perfect foresight but solely rely on data about the present. Our result indicate that the results of the control strategies obtained using the proposed method are comparable to the results of the linear optimisations, in our case in terms of emissions and prices.

Assuming a two component, positive and negative mass, superfluid/supersolid for space (the Winterberg model), we model the Higgs field as a condensate made up of a positive and a negative mass, planckion pair. The connection is shown to be consistent (compatible) with the underlying field equations for each field, and the continuity equation is satisfied for both species of planckions, as well as for the Higgs field. An inherent length scale for space (the vacuum) emerges, which we estimate from previous work to be of the order of,

This paper reports applying Minimax principle and impulsive differential inequality to derive the existence of multiple stationary solutions and the global stability of a positive stationary solution for a delayed feedback Gilpin-Ayala competition model with impulsive disturbance. The conclusion obtained in this paper reduces the conservatism of the algorithm compared with the known literature, for the impulsive disturbance is not limited to impulsive control.

Supplier selection (SC) continues to be a crucial component in manufacturing procurement. Using the PLCC advantages generates revenue and lowers costs more than might be anticipated. Supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. Past literature on this topic is limited. We try to close this gap in knowledge. In this study, we attempt to apply two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we are comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology Company; this cloud makes company decision–makers focus on low PLCC and select a better supplier in sustainable supply chains development.

One of the key challenges of stock trading is the stock prices follow a random walk process, which is a special case of a stochastic process, and are highly sensitive to new information. A random walk process is difficult to predict in the short-term. Many linear process models that are being used to predict financial time series are structural models that provide an important decision boundary, albeit not adequately considering the correlation or causal effect of market sentiment on stock prices. This research seeks to increase the predictive capability of linear process models using the SPDR S\&P 500 ETF (SPY) and the CBOE Volatility (VIX) Index as a proxy for market sentiment. Three econometric models are considered to forecast SPY prices: (i) Auto-Regressive Integrated Moving Average (ARIMA), (ii) Generalized Auto Regressive Conditional Heteroskedasticity (GARCH), and (iii) Vector Autoregression (VAR). These models are integrated into two technical indicators, Bollinger Bands and Moving Average Convergence Divergence (MACD), focusing on forecast performance. The profitability of various algorithmic trading strategies is compared based on a combination of these two indicators. This research finds that linear process models that incorporate the VIX Index do not improve the performance of algorithmic trading strategies.

Supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology company; this cloud makes company decision–makers focus on low PLCC and select a better supplier in sustainable supply chains goal.

Laser reduced graphene oxide (LRGO) on a PET substrate was prepared in one-step to obtain the LRGO grid electrode for sensitive carbaryl determination. The grid form results in a grid distribution of different electrochemically active zones affecting the electroactive substance diffusion towards to the electrode surface and increasing the electrochemical sensitivity for carbaryl determination. Carbaryl is electrochemically irreversibly oxidized by the secondary amine moiety of the molecule with the loss of one proton and one electron in the pH range from 5 to 7 by LSV on the LRGO grid electrode with a scan rate of 300 mV/s. Some interference of the juice matrix molecules did not significantly affect the LSV oxidation current of carbaryl on the LRGO grid electrode after adsorptive accumulation without applied potential. The LRGO grid electrode can be used for LSV determination of carbaryl in fruit juices in the concentration range from 0.25 to 128 mg/L with LOD of 0.1 mg/L by. The fabrication of the LRGO grid electrode opens up possibilities for further inexpensive monitoring of carbaryl in other fruit juices and fruits.

Using the PLCC advantages generates revenue and lowers costs more than might be anticipated. It ensures better decisions by using a more perfect and practical assessment of revenues and costs. Although the supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology company; this cloud make company decision–makers focus on low PLCC and select better supplier.

Today’s purchasing companies demand an advanced buyer equal of enactment from their supplier while the two parties maintain a respectful connection. Although the supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology comapny; this cloud make company decision–makers focus on low PLCC and select better supplier.

We define degree of dependence of two events A and B in a probability space by using Boltzmann-Shannon entropy function of an appropriate probability distribution produced by these events and depending on one parameter (the probability of intersection of A and B) varying within a closed interval I. The entropy function attains its global maximum when the events A and B are independent. The important particular case of discrete uniform probability space motivates this definition in the following way. The entropy function has a minimum at the left endpoint of I exactly when one of the events and the complement of the other are connected with the relation of inclusion (maximal negative dependence). It has a minimum at the right endpoint of I exactly when one of these events is included in the other (maximal positive dependence). Moreover, the deviation of the entropy from its maximum is equal to average information that carries one of the binary trials defined by A and B with respect to the other. As a consequence, the degree of dependence of A and B can be expressed in terms of information theory and is invariant with respect to the choice of unit of information. Using this formalism, we describe completely the screening tests and their reliability, measure efficacy of a vaccination, the impact of some events from the financial markets to other events, etc. A link is available for downloading an Excel program which calculates the degree of dependence of two events in a sample space with equally likely outcomes.

Frequency estimation of a single sinusoid in colored noise has received a considerable amount of attention in the research community. Taking into account the recent emergence and advances in compressive covariance sensing (CCS), the aim of this work is to combine the two disciplines by studying the effects of compressed measurements of a single sinusoid in moving-average (MA) colored noise on its frequency estimation accuracy. CCS techniques can recover the second-order statistics of the original uncompressed signal from the compressed measurements, thereby enabling correlation-based frequency estimation of single tones in colored noise using higher-order lags. Acceptable accuracy is achieved for moderate compression ratios and for a sufficiently large number of available compressed signal samples. It is expected that the proposed method would be advantageous in applications involving resource-limited systems such as wireless sensor networks.

This paper answers the need to plan a cost-minimizing charging schedule for electric buses and proposes a three-stage procedure, which is oriented around the participation of electric buses aggregator in a day-ahead energy auction. First, optimization models are provided to determine charging availability expressed as minimum and maximum hourly energy requirements taking into account detailed, minutely characteristics and constraints of the charging equipment and the buses. Next, the auction model is formulated by considering aggregated bids submitted by the electric buses aggregator once the charging availability is determined. Hence, the day-ahead prices reflect the optimal schedules of auction participants, and the bus aggregator is safe against peak-hour charging. Finally, hourly auction-based schedules are disaggregated into optimal minutely charging schedules. Mixed-integer linear programming models are formulated for aggregation-disaggregation stages investigated in this paper, while the variables and constraints introduced into the auction model are linear. The proposed methodology has been verified on a recently published case study of a real-world bus service operated on The Ohio State University campus. We show that the auction-based charging of all 22 buses outperforms as-soon-as-possible schedules by 7% to even 28% of daily cost savings. Using the aggregated bids, buses can flexibly shift charges between high- and low-price periods while preserving constraints of the charging equipment and timetables.

Damage in concrete structures initiates as the growth of diffuse microcracks that is followed by damage localisation and eventually leads to structural failure. Weak changes such as diffuse microcracking processes are failure precursors. Identification and characterisation of these failure precursors at an early stage of concrete degradation and application of suitable precautionary measures will considerably reduce the costs of repair and maintenance. To this end, a reduced order multiscale model for simulating microcracking-induced damage in concrete at the mesoscale levelis proposed. The model simulates the propagation of microcracks in concrete using a two-scale computational methodology. First, a realistic concrete specimen that explicitly resolves the coarse aggregates in a mortar matrix was generated at the mesoscale. Microcrack growth in the mortar matrix is modelled using a synthesis of continuum micromechanics and fracture mechanics. Model order reduction of the two-scale model is achieved using clustering technique. Model predictions are calibrated and validated using uniaxial compression tests performed in the laboratory.

The Lamiaceae belong to the species-richest families of flowering plants and harbor many species used as herbs or for medicinal applications, such as Basils or Mints. Evolution of this group has been driven by chemical speciation, mainly of Volatile Organic Compounds (VOCs). The commercial use of these plants is characterized by a large extent of adulteration and surrogation. To authenticate and discern the species, is, thus, relevant for consumer safety, but usually requires cumbersome analytics, such as Gas Chromatography, often to be coupled with Mass Spectroscopy. We demon-strate here that quartz-crystal microbalance (QCM)-based electronic noses provide a very cost-efficient alternative, allowing for a fast, automated discrimination of scents emitted from leaves of different plants. To explore the range of this strategy, we used leaf material from four genera of Lamiaceae along with Lemongrass as similarly scented, but non-related outgroup. In order to unambiguously differentiate the scents from the different plants, the output of the 6 different SURMOF/QCM sensors was analyzed using machine learning (ML) methods, together with a thorough statistical analysis. The exposure and purging datasets (4 cycles) obtained from a QCM-based, low-cost homemade portable e-Nose were analyzed with Linear Discriminant Analysis (LDA) classification model. Prediction accuracies with repeating test measurements reached values of up to 90%. We show that it is not only possible to discern and identify plants on the genus level, but even to discriminate closely related sister clades within a genus (Basil), demonstrating that e-Noses are a powerful technology to safeguard consumer safety against the challenges of globalized trade.

In this article, the usual factorials and binomial coefficients have been generalized and extended to the negative integers. Basing on this generalization and extension, a new kind of polynomials has been proposed, which led directly to the non-classical hypergeometric orthogonal polynomials and the non-classical second-order hypergeometric linear DEs. The resulting polynomials can be used in non-relativistic and relativistic QM, particularly, in the case of the Schrödinger equation, and Dirac equations for an electron in a Coulomb potential field.

In spite of numerous predictions, the natural herd immunity for covid-19 visru had not been approahed anywhere in the world. Thus, the traditional mathematical models of disease spread demonstrated their inability to describe adequately the covid-19 pandemic. In author's works, the novel model of the disease spread was developed. This model reflects the basic features of the covid-19 pandemic: a) the social clustering character of virus spread, b) . Social clustering is mathematically modelled with ultrametric spaces having the treelike geometry encoding hierarchy of the regulation constraints. The virus spread is described by ultrametric diffusion or random walk on the hierarchic energy landscape. In contrast to the standard models which are characterized by the exponential decrease of the probability to become infected - at the stage of approaching of the herd immunity, the ultrametric model is characterized by the power law. Moreover, the model gives the possibility to quantify the influence of restriction measures up to the lockdown. Our main result is that the play with restrictions, including lockdowns, is counterproductive and leads to the essential slowdown of approaching the herd immunity or even makes this impossible.

The relativistic quantum motion of a scalar particle under the effects of violation of the Lorentz symmetry in the presence of a linear confining potential is investigated. We see that the solution of the bound state to the modified Klein-Gordon equation can be obtained and a quantum effect characterized by the dependence of the magnetic field on the quantum numbers of the system is observed

In this work, linear confinement of a relativistic scalar particle under the effects of Lorentz symmetry violation is investigated. We introduce a scalar potential by modifying the mass via transformation M → M + S(r) in the wave equation, and analyze the effects on the eigenvalues and the wave function. We see that the solution of the bound state to the wave equation can be achieved, and the energy eigenvalues and the wave function modified by the Lorentz symmetry breaking parameters as well as potential

The 32CA reactions of a series of pairs of bent three-atom-components (B-TACs) and linear TACs (L-TACs) towards electrophilic dicyanoethylene (DCE) have been studied within the Molecular Electron Density Theory in order to understand their different reactivity. ELF analysis indicates that while pseudodiradical B-TACs change their electronic structure to pseudoradical or carbenoid L-TACs upon dehydrogenation, zwitterionic B-TACs experience no remarkable change. Analysis of the CDFT indices indicates that five of the nine studied TACs have a strong nucleophilic character, thus participating in polar reactions towards electrophilic ethylenes. The activation energies of the 32CA reactions of the nine TACs towards electrophilic DCE range from 0.6 to 22.0 kcal·mol-1, which are by between 2.0 and 10.1 kcal·mol-1 lower than those involved in the non-polar 32CA reactions with ethylene. In general, B-TACs are more reactive than their L-TAC counterparts. A change of the regioselectivity is found in these polar 32CA reactions; in general, while B-TACs are meta regioselective, L-TACs are ortho regioselective. Analysis of the geometrical parameters indicates that at all TSs, the formation of the single bond involving the most electrophilic C4 carbon of DCE is more advanced than that involving the C5 one. A change of the asynchronicity in the reactions involving B-TACs and L-TACs is also found.

The present paper introduces a new class of Stancu-Kantorovich operators constructed in the King sense. For this class of operators we establish some convergence results, error estimations theorems and graphical properties of approximation for the cases considered, namely, operators that preserve the test functions $e_{0}(x)=1$ and $e_{1}(x)=x$, $% e_{0}(x)=1$ and $e_{2}(x)=x^{2},$ as well as $e_{1}(x)=x$ and $e_{2}(x)=x^{2} $. The new class of operators introduced in this paper is a genuine generalization of the class introduced by Indrea et al. (see Indrea A., Indrea A., Pop O. A New Class of Kantorovich-Type Operators, Constructive Mathematical Analysis).

Ocean surface waves have been utilized as fundamental information in various fields of oceanic research. In this paper, we suggest a simulation and modelling technique for generating an ocean surface wave using an inverse Fast Fourier Transform (iFFT), and we subsequently verify the wave’s accuracy. The conventional method, linear superposition, requires recursive calculation because of the double summation and the time variable; to circumvent this issue, the new algorithm is presented. The Joint North Sea Wave Project (JONSWAP) spectrum is utilized for the ocean surface wave simulation example, and the parameters are the significant wave height (HS) and the zero-crossing wave period (TZ). A coordinate transform for the wavenumber domain was used to apply the inverse FFT algorithm. To verify the accuracy of the simulation result, the relative error between the input condition and the analysis result was calculated. The result for TZ is below 4% relative error, and the maximum relative error for HS is 7%. To avoid the Nyquist frequency for wave-field analysis and simulation, the minimum grid size was calculated by twice applying the maximum wavenumber.

Studies have shown that in many practical applications, data interpolation by splines leads to better approximation and higher computational efficiency as compared to data interpolation by a single polynomial. Data interpolation by splines can be significantly improved if knots are allowed to be free rather than at a priori fixed locations such as data points. In practical applications, the smallest possible curvature is often desired. Therefore, optimal splines are determined by minimizing a derivative of continuously differentiable functions comprising the spline of the required order. The problem of obtaining an optimal spline is tantamount to minimizing derivatives of a nonlinear differentiable function over a Banach space on a compact set. While the problem of data interpolation by quadratic splines has been accomplished analytically, interpolation by splines of higher orders or in higher dimensions is challenging. In this paper, to overcome difficulties associated with the complexity of the interpolation problem, the interval over which data points are defined, is discretized and continuous derivatives are substituted by their discrete counterparts. It is shown that as the mesh of the discretization approaches zero, a resulting near-optimal spline approaches an optimal spline. Splines with the desired accuracy can be obtained by choosing an appropriate mesh of the discretization. By using cubic splines as an example, numerical results demonstrate that the linear programming (LP) formulation, resulting from the discretization of the interpolation problem, can be solved by linear solvers with high computational efficiency and resulting splines provide a good approximation to the optimal splines.

This article presents answers to the questions on superresolution and structured illumination microscopy as raised in the editorial of a recent publication [K. Prakash et al. arXiv, 2102.13649, 2021]. The answers are based on my personal views on superresolution in light microscopy, supported by reasoning. Discussed are the definition of superresolution, Abbe’s resolution limit and the classification of superresolution methods into non-linear-, prior-knowledge- and near-field-based superresolution. A further focus is put on capabilities and technical aspects of present and future structured illumination microscopy (SIM) methods.

This review describes the subjective experience of visual aura in migraine, outlines theoretical models of this phenomenon, and explores how these may be linked to neurochemical, electrophysiological and psychophysical differences in sensory processing that have been reported in migraine with aura. Reaction-diffusion models have been used to model the hallucinations thought to arise from cortical spreading depolarisation and depression in migraine aura. One aim of this review is to make the underlying principles of these models accessible to a general readership. Cortical spreading depolarisation and depression in these models depends on the balance of the diffusion rate between excitation and inhibition, and the occurrence of a large spike in activity to initiate spontaneous pattern formation. We review experimental evidence, including recordings of brain activity made during the aura and attack phase, self-reported triggers of migraine, and psychophysical studies of visual processing in migraine with aura, and how these might relate to mechanisms of excitability that make some people susceptible to aura. Increased cortical excitability, increased neural noise, and fluctuations in oscillatory activity across the migraine cycle are all factors likely to contribute to the occurrence of migraine aura. There remain many outstanding questions relating to the current limitations of both models and experimental evidence. Nevertheless, reaction-diffusion models, by providing an integrative theoretical framework, support the generation of testable experimental hypotheses to guide future research.

An image consisting of (m, n) pixels can be seen as a matrix of m × n size. Based on the formula of angles between two subspaces, a pair of angles can be defined between two matrices, by utilizing column spaces and row spaces of the two matrices. The singular values of each matrix can be used to calculate distances. Thus, a distance representation is obtained, and a pair of angles between 2 matrices of the same size.

Given a quasi-definite linear functional u in the linear space of polynomials with complex coefficients let us consider the corresponding sequence of monic orthogonal polynomials (SMOP in short) (Pn)n≥0. For the Christoffel transformation u˜=(x−c)u with SMOP (P˜n)n≥0, we are interested to study the relation between u˜ and u(1)˜, where u(1) is the linear functional for the associated orthogonal polynomials of the first kind (Pn(1))n≥0 and u(1)˜=(x−c)u(1) is its Christoffel transformation. This problem is also studied for the Geronimus transformations.

One of the non-linear phenomena that affect high bandwidth and long reach communication systems is the non-linear phenomenon called four-wave mixing (FWM). Unfortunately, the simulation of such systems aiming to obtain their design parameter limitations require more time as the number of channels increases. In this paper, we propose a new high-performance computational model to obtain optimal design parameters in a multi san Dense Wavelength Division Multiplexing (DWDM) system, limited by FWM and the intrinsic Amplified Spontaneous Emission (ASE) noise of optical amplifiers employed in each segment. The simulation in this work provides a complete optical design characterization and compares the efficiency and speed improvement of the proposed parallelization model versus a previous sequential model. Additionally, an analysis of the computational complexity of parallel model is presented, where two parallel implementations are used. First, Open Multi−Processing (OpenMP), based on the use of a central, multi-core processing unit is used and secondly the Compute Unified Device Arquitecture (CUDA), which is based on the use of graphics processing unit. Results show that parallelism improves to up to 40 times the performance of the simulation when nested parallelization with CUDA is used, over de sequential method and up to 6 times compared with the implementation with OpenMP using 12 processors. Within our parallel implementation, it is possible to simulate with an increased number of channels, that was unpractical in the sequential simulation.

The overrun of transient power quality index caused by the large-capacity electric arc furnace (EAF) has become a prominent problem affecting the safe and stable operation of the power system. (1) In this paper, the relationship between arc furnace volt-age and current is derived based on the different stages of arc combustion, and the random variation of chaotic phenomenon of the arc voltage are simulated. Established an EAF model suitable for the study of transient power quality problems. (2) Take 50t AC EAF as an example to analyze the reactive power impact and the influence on the point of common coupling (PCC) voltage caused by the three-phase short circuit of the electrode. The results show that the experimental results are consistent with the theoretical analysis, verifying the correctness and effectiveness of the model. (3) When the three-phase short-circuit occurs, the reactive power impact is nearly 6 times that of normal operation, the short-circuit current is 2.66 times that of normal operation, and the effective value of the PCC voltage has dropped by 40.37%, which provides a theoretical basis for real-time compensation of impulsive reactive power and improvement of the transient power quality of the EAF.

Abstract Unlike accelerated motion or curvalinear motion,a nonlinear motion state(non-inertial system) can be described by differential equations or the other algebric equations in axiom 2, the accelerated motion in axiom 3 can be considered to be described by using the equation of the linear and curvilinear process of the continuum extending to infinitely distance.Further, this linear and curvilinear process of the continuum is a quantitative continuum in essence as a unity of infinitely quantities and infinitely dimensions at infinite distance (infinity) relative to all orientations in which we exist. These indicates that an accelerated motion accumulates continuously started from a finite quantities, leaping to transit from finite to infinite quantities by an infinitely great accelerating force.

Refinery planning optimization is a challenging problem as regards handling the nonconvex bilinearity mainly due to pooling operations in processes such as crude oil distillation and product blending. This work investigates the performance of several representative piecewise-linear (or piecewise-affine) relaxation schemes (referred to as McCormick, bm, nf5, nf6t, and de (which is a new approach proposed based on eigenvector decomposition) that mainly give rise to mixed-integer optimization programs to convexify a bilinear term using predetermined univariate partitioning for instances of uniform and non-uniform partition sizes. Computational results show that applying these schemes give improved relaxation tightness than only applying convex and concave envelopes as estimators. Uniform partition sizes typically perform better in terms of relaxation solution quality and convergence behavior. It is also seen that there is a limit on the number of partitions that contributes to relaxation tightness, which does not necessarily correspond to a larger number of partitions, while a direct relation between relaxation size and tightness does not always hold for non-uniform partition sizes.

In this study, we investigate the performance of the saddlepoint approximation of the probability mass function and the cumulative distribution function for the weighted sum of independent Poisson random variables. The goal is to approximate the hazard rate function for this complicated model. The better performance of this method is shown by numerical simulations and comparison with a performance of other approximation methods.

Cold chain logistics of Agricultural Products demand forecasting can provide the scientific basis for the country to formulate logistics strategy, which further promotes the development of social economy and the improvement of living standards in China. In this paper, a new mathematical combined model is proposed to Agricultural Products Demand. Shandong, one of a China’s province, serves as the main producer and distributor of agricultural products. Based on the index system created from multiple related factors influencing cold chain logistics demand of agricultural products in Shandong, this paper employs principal component analysis to reduce the dimension of various indexes and predicts principal components with time series. Thereafter, multiple linear regression model and neural network model were constructed to forecast the cold chain logistics demand of agricultural products in Shandong, and their combined forecast models were compared. What's more, the paper provides insight for reference and decision-making concerning the development of cold chain logistics industry of agricultural products in Shandong province.

Searching, recognizing and retrieving a video of interest from a large collection of a video data is an instantaneous requirement. This requirement has been recognized as an active area of research in computer vision, machine learning and pattern recognition. Flower video recognition and retrieval is vital in the field of floriculture and horticulture. In this paper we propose a model for the retrieval of videos of flowers. Initially, videos are represented with keyframes and flowers in keyframes are segmented from their background. Then, the model is analysed by features extracted from flower regions of the keyframe. A Linear Discriminant Analysis (LDA) is adapted for the extraction of discriminating features. Multiclass Support Vector Machine (MSVM) classifier is applied to identify the class of the query video. Experiments have been conducted on relatively large dataset of our own, consisting of 7788 videos of 30 different species of flowers captured from three different devices. Generally, retrieval of flower videos is addressed by the use of a query video consisting of a flower of a single species. In this work we made an attempt to develop a system consisting of retrieval of similar videos for a query video consisting of flowers of different species.

Remote sensing is one of the modern methods that have significantly developed over the last two decades and nowadays provides a new means for forest monitoring. High spatial and temporal resolutions are demanded for accurate and timely monitoring of forests. In this study multi-spectral Unmanned Aerial Vehicle (UAV) images were used to estimate canopy parameters (definition of crown extent, top and height as well as photosynthetic pigment contents). The UAV images in Green, Red, Red-Edge and NIR bands were acquired by Parrot Sequoia camera over selected sites in two small catchments (Czech Republic) covered dominantly by Norway spruce monocultures. Individual tree extents, together with tree tops and heights, were derived from the Canopy Height Model (CHM). In addition, the following were tested i) to what extent can the linear relationship be established between selected vegetation indexes (NDVI and NDVIred edge) derived for individual trees and the corresponding ground truth (e.g., biochemically assessed needle photosynthetic pigment contents), and ii) whether needle age selection as a ground truth and crown light conditions affect the validity of linear models. The results of the conducted statistical analysis show that the two vegetation indexes (NDVI and NDVIred edge) tested here have a potential to assess photosynthetic pigments in Norway spruce forests at a semi-quantitative level, however the needle-age selection as a ground truth was revealed to be a very important factor. The only usable results were obtained for linear models when using the 2nd year needle pigment contents as a ground truth. On the other hand, the illumination conditions of the crown proved to have very little effect on the model’s validity. No study was found to directly compare these results conducted on coniferous forest stands. This shows that there is a further need for studies dealing with a quantitative estimation of the biochemical variables of nature coniferous forests when employing spectral data acquired by the UAV platform at a very high spatial resolution.

The airport ground handling services (AGHS) equipment supplier selection problem involves a safety guarantee on the part of the AGHS company that carries out the daily work. AGHS company can prevent aircraft damage and delays in airlines schedules, and ensure reliable and high-quality ground handling service. In our research, we developed an AGHS equipment supplier selection model based on the analytic hierarchy process and an AHP weighted fuzzy linear programming approach, and we solved the AGHS equipment supplier’s selection problem. The main objective of this article is to create an AHP and AHP-FLP decision model in order to help the AGHS company authorities select the best AGHS equipment supplier. The practical application in AGHS equipment supplier selection decisions can be interpreted as demonstrating that the proposed model provides knowledge and practical value for the AGHS industry.

Mints emit diverse scents that exert specific biological functions and are relevance for applications. The current work strives to develop electronic noses that can electronically discriminate the scents emitted by different species of Mint as alternative to conventional profiling by gas chromatography. Here, 12 different sensing materials including 4 different metal oxide nanoparticle dispersions (AZO, ZnO, SnO2, ITO), one Metal-Organic Frame as Cu(BPDC), and 7 different polymer films including PVA, PEDOT: PSS, PFO, SB, SW, SG, PB were used for functionalizing of QCM sensors. The purpose was to discriminate six economically relevant Mint species (Mentha x piperita, Mentha spicata, Mentha spicata ssp. crispa, Mentha longifolia, Agastache rugosa, and Nepeta cataria). The adsorption and desorption datasets obtained from each modified QCM sensor were processed by three different classification models including Principal Component Analy-sis (PCA), Linear Discriminant Analysis (LDA), and k-Nearest Neighbor Analysis (k-NN). This allowed discriminating the different Mints with classification accuracies of 97.2% (PCA), 100% (LDA), and 99.9% (k-NN), respectively. Prediction accuracies with a repeating test measurement reached up to 90.6% for LDA, and 85.6% for k-NN. These data demonstrate that this electronic nose can discriminate different Mint scents in a reliable and efficient manner.

The Internet-of-Things (IoT) triggers new types of cyber risks. Therefore, the integration of new IoT devices and services requires a self-assessment of IoT cyber security posture. By security posture this article refers to the cybersecurity strength of an organisation to predict, prevent and respond to cyberthreats. At present, there is a gap in the state-of-the-art, because there are no self-assessment methods for quantifying IoT cyber risk posture. To address this gap, an empirical analysis is performed of 12 cyber risk assessment approaches. The results and the main findings from the analysis is presented as the current and a target risk state for IoT systems, followed by conclusions and recommendations on a transformation roadmap, describing how IoT systems can achieve the target state with a new goal-oriented dependency model. By target state, we refer to the cyber security target that matches the generic security requirements of an organisation. The research paper studies and adapts four alternatives for IoT risk assessment and identifies the goal-oriented dependency modelling as a dominant approach among the risk assessment models studied. The new goal-oriented dependency model in this article enables the assessment of uncontrollable risk states in complex IoT systems and can be used for a quantitative self-assessment of IoT cyber risk posture.

An adaptive control technique has been implemented for DSTATCOM for power quality enhancement in three phase four wires(3P4W) distribution system. The reference source currents are extracted from active components of load current for each phase by using this technique. It has also been used for load balancing, harmonic suppression, power factor improvement and reactive power compensation in distribution system. The adaptive control technique has been tested at varying load in steady state and dynamic conditions. This technique is developed using MATLAB/Simulink and source side harmonics are mitigated under different load conditions which are acceptable in accordance with IEEE standard.

Mitochondrial disorders, although heterogeneous, are traditionally described as conditions characterized by encephalomyopathy, hypotonia and progressive postnatal organ failure. Here we provide a systematic review of Linear Skin Defects with Multiple Congenital Anomalies (LSDMCA), a rare unconventional mitochondrial disorder which presents as a developmental disease; its main clinical features include microphthalmia with different degrees of severity, linear skin lesions, and central nervous system malformations. The molecular basis of this disorder has been elusive for several years. Mutations were eventually identified in three X-linked genes, i.e., HCCS, COX7B, and NDUFB11, which are all endowed with defined roles in the mitochondrial respiratory chain. A peculiar feature of this condition is its inheritance pattern: X-linked dominant male-lethal. Only female or XX male individuals can be observed, implying that nullisomy for these transcripts is incompatible with normal embryonic development in mammals. All three genes undergo X-inactivation that, according to our hypothesis, may contribute to the extreme variable expressivity observed in this condition. We propose that mitochondrial dysfunction should be considered as an underlying cause in developmental disorders. Moreover, LSDMCA should be taken into consideration by clinicians when dealing with patients with microphthalmia with or without associated skin phenotypes.

The motion of a circular elastic plate floating on the surface is investigated in the time–domain. The solution is found from the single frequency solutions and the method to solve for the circular plate is given using the eigenfunction matching method. Simple plane incident waves with a Gaussian profile in wavenumber space are considered and a more complex focused wave group is considered. Results are given for a range of plate and incident wave parameters are investigated. Code is provided to show how to simulate the complex motion.

In order to overcome this problem our group designed a novel machine learning technique, multivariate linear method (MLM) which can capture convergent data from voxel-based morphometry, functional resting state and task-related neuroimaging and the relevant clinical measures. In this paper we report results from convergent cross-validation of biological signatures of disease in a sample of patients with schizophrenia as compared to depression. Our model provides evidence that the combination of the neuroimaging and clinical data in MLM analysis can inform the differential diagnosis in terms of incremental validity to reach 90 % accuracy of the prediction.

We present a cost- and time-efficient method for the controlled preparation of single phase La(IO3)3 nanoparticles via a simple soft-chemical route which takes a matter of hours, thereby providing an alternative to the common hydrothermal method which takes days. Nanoparticles of pure α-La(IO3)3 and pure δ-La(IO3)3 were synthesised via the new method depending on the source of iodate ions, thereby demonstrating the versatility of the synthesis route. The crystal structure, nanoparticle size-dispersal and chemical composition were characterised via angle- and energy-dispersive powder X-ray diffraction, scanning electron microscopy and Fourier-transform infrared spectroscopy.

In this paper, we address the problem of stabilization of switched linear systems. The idea is to look for a state feedback control law using evolutionary algorithms (EA) in order to assure the stability of the switched linear systems under control constraints. In some cases when states are not available and only outputs are measurable, the previous method is applied to design an output feedback controller which stabilizes the system. Both stabilizing controllers are developed using deferential evolution and genetic algorithm. Two numerical examples illustrate our proposed theory and point out the effectiveness of our proposed approaches.

In this paper we analyze and propose new method and algorithm of selecting the optimal labor time as a function of skills following our main references Mirrlees (1971), Saez (2001) and Stancheva (2014). The optimal labor time is a situation when the utility function of individual reaches a maximum. One of the main differences with Saez (2001) is our algorithm for creation the skill distribution

In recent years, there have been frequent reports on the adverse effects of synthetic cannabinoid (SC) abuse. SCs cause psychoactive effects, similar to those caused by marijuana, by binding and activating cannabinoid receptor 1 (CB1R) in the central nervous system. The aim of this study was to establish a reliable quantitative structure-activity relationship (QSAR) model to correlate the structures and physicochemical properties of various SCs with their CB1R-binding affinities. We prepared 15 SCs and their derivatives (tetrahydrocannabinol [THC], naphthoylindoles, and cyclohexylphenols) and determined their binding affinity to CB1R, which is known as a dependence-related target. We calculated the molecular descriptors for dataset compounds using an R/CDK (R package integrated with CDK, version 3.5.0) toolkit to build QSAR regression models. These models were established and statistical evaluations were performed using the mlr and plsr packages in R software. The most reliable QSAR model was obtained from the partial least squares regression method via external validation. This model can be applied in vivo to predict the addictive properties of illicit new SCs. Using a limited number of dataset compounds and our own experimental activity data, we built a QSAR model for SCs with good predictability. This QSAR modeling approach provides a novel strategy for establishing an efficient tool to predict the abuse potential of various SCs and to control their illicit use.

Complex diseases such as cancer are caused by changes in the Gene Regulatory Networks. Systems that model the complex dynamics of these networks along with adapting to real gene expression data are closer to reality and can help understand the creation and treatment of cancer. In this paper, for the first time, modelling of gene regulatory networks is performed using delayed nonlinear variable order fractional systems in the state space by a new tool called GENAVOS. This tool uses gene expression time series data to identify and optimize system parameters. This software has several tools for analyzing system dynamics. The results show that the nonlinear variable order fractional systems have very good flexibility in adapting to real data. We found that regulatory networks in cancer cells actually have a larger delay parameter than in normal cells. It is also possible to create chaos, periodic and quasi-periodic oscillations by changing the delay, degradation and synthesis rates. Our findings indicate a profound effect of time-varying order on these networks, which may be related to a type of cellular memory due to epigenetic and environmental factors. We showed that by changing the delay parameter and the variable order function for a normal cell system, its behavior changes and becomes quite similar to the behavior of a cancer cell. This work also confirms the effective role of the miR-17-92 cluster in the cancer cell cycle. GENAVOS is available at https://github.com/hanif-y/GENAVOS with its user guide and MATLAB codes.

In this paper, we present an extended version of the Hadi-Vencheh model for multiple criteria ABC inventory classification. The proposed model is a nonlinear weighted product model (WPM) which determines a common set of weights for all the items. Our proposed nonlinear WPM incorporates multiple criteria with different measure units, without converting the performance of each inventory item in terms of each criterion into a normalized attribute value, thereby providing an improvement over the model proposed by Hadi-Vencheh. Our study mainly includes various criteria for ABC classification, and demonstrates an efficient algorithm for solving nonlinear programming problems in which the feasible solution set does not have to be convex. The algorithm presented in this study improves the solution efficiency of the Canonical Coordinates Method (CCM) algorithm substantially when applied to large scale, nonlinear programming problems. The modified algorithm was tested to compare our proposed model results to the results derived using the Hadi-Vencheh model and demonstrate the algorithm's efficacy. The practical implications of the study are to develop an efficient nonlinear optimization solver by optimizing the quality of existing solutions, thus improving time and space efficiency.

In this work, fluorinated graphene nanoscrolls (FGN) were synthesized via facile chemical methods under simple and mild conditions. Interestingly, the formation of the featured FGN was significantly solvent sensitive. Experimental results indicated that in the presence of aprotic solvent, for example, N,N dimethylformamide (DMF), the reaction system inclined to form the interesting FGN nanostructures. The structure and morphology of the prepared FGN were detailed characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) etc. The obtained FGN was used as a cathode material for primary lithium ion batteries with superior discharge specific capacity (eg. 979.3 mAhg-1), stable discharge platform and high energy density (eg. 2287.9 Wh kg-1), which fosters it a high density, low cost and durable candidate for cathode material for lithium ion batteries..

To investigate the effect of Polyvinylpyrrolidone (PVP) addition and consequently porosity, two different sets of membranes are manufactured, since PVP is a widely used poring agent which has an impact on the mechanical properties of the membrane material. The first set (PAN 1) includes PAN and the necessary solvent while the second set (PAN 2) is made of PAN and PVP. These membranes are put through several characterisation processes including tensile testing. The obtained data are used to model the static behaviour of the membranes with different geometries, but similar loading and boundary conditions that represent their operating conditions. This modelling process is undertaken by using finite element method. The main idea is to investigate how geometry affects the load-carrying capacity of the membranes. Alongside membrane modelling, their materials are modelled with representative elements with hexagonal and rectangular pore arrays (RE) to understand the impact of porosity on the mechanical properties. Exploring the results, the best geometry is found as the elliptic membrane with the aspect ratio 4 and the better RE as the hexagonal array which can predict the elastic properties with an approximate error of 12%.

The Thermodynamic Formalism provides a rigorous mathematical framework to study quantitative and qualitative aspects of dynamical systems. At its core there is a variational principle and corresponding, in its simplest form, to the Maximum Entropy principle, used as a statistical inference procedure to represent, by specific probability measures (Gibbs measures), the collective behaviour of complex systems. This framework has found applications in different domains of scienThe Thermodynamic Formalism provides a rigorous mathematical framework to study quantitative and qualitative aspects of dynamical systems. At its core there is a variational principle and corresponding, in its simplest form, to the Maximum Entropy principle, used as a statistical inference procedure to represent, by specific probability measures (Gibbs measures), the collective behaviour of complex systems. This framework has found applications in different domains of science, in particular, has been fruitful and influential in neurosciences. In this article, we review how the Thermodynamic Formalism can be exploited in the field of theoretical neuroscience, as a conceptual and operational tool, to link the dynamics of interacting neurons and the statistics of action potentials from either experimental data or mathematical models. We comment on perspectives and open problems in theoretical neuroscience that could be addressed within this formalism.ce, in particular, has been fruitful and influential in neurosciences. In this article, we review how the Thermodynamic Formalism can be exploited in the field of theoretical neuroscience, as a conceptual and operational tool, to link the dynamics of interacting neurons and the statistics of action potentials from either experimental data or mathematical models. We comment on perspectives and open problems in theoretical neuroscience that could be addressed within this formalism.

Indian cities are increasingly becoming susceptible to PM10 induced health effects which have become a matter of concern for the policymakers of the country. Air pollution is engulfing the comparatively smaller cities as the rapid pace of urbanization, and economic development seems not to lose steam ever. A review of air pollution of 28 cities of India, which includes tier-I, II, and III cities of India, found to have grossly violated both WHO and NAAQS standards in respect of acceptable daily average PM10 concentrations by a wide margin. Predicting the city level PM10 concentrations in advance and accordingly initiate prior actions is an acceptable solution to save the city dwellers from PM10 induced health hazards. Predictive ability of three models, linear MLR, nonlinear MLP (ANN), and nonlinear CART, for one day ahead PM10 concentration forecasting of tier-II Guwahati city, were tested with 2016-2018 daily average observed climate data, PM10, and gaseous pollutants. The results show that the non-linear algorithm MLP with feedforward backpropagation network topologies of ANN class, giving the best prediction value when compared with linear MLR and nonlinear CART model. ANN (MLP) approach, therefore, may be useful to effectively derive a predictive understanding of one day ahead PM10 concentration level and thus provide a tool to the policymakers for improving decision-making associated with air pollution and public health.

In this work, we treat a prediction problem via the conditional hazard function of a scalar response variable Y given a functional random variable X by using the local linear technique. The main purpose of this paper is to investigate the asymptotic normality of the nonparametric estimator of the conditional hazard function, under some general conditions. A simulation study, conducted to assess finite sample behavior, demonstrates the superiority of our method than the standard kernel method

This paper is a slightly modified, abridged version of a previous work ``Parametric Gevrey asymptotics in two complex time variables through truncated Laplace transforms'' motivated by our contribution in the conference ``Formal and Analytic Solutions of Diff. (differential, partial differential, difference, q-difference, q-difference-differential) Equations on the Internet'' (FASnet20). It aims to clarify and give further detail at some crucial points concerning the asymptotic behavior of the solutions of the problems studied in that work.

Soil quality assessment based on crop yields and identification of key indicators of it can be used for better management of agricultural production. In the current research, the weighted additive soil quality index (SQIw), factor analysis (FA) and multiple linear regression (MLR) method are used to assess the soil quality of rainfed winter wheat fields with two soil orders on 53.20 km2 of agricultural land in western Iran. A total of 18 soil quality indicators were determined for 100 soil samples (0-20 cm depth) from two soil orders (Inceptisols and Entisols). The soil properties measured were: pH, soil texture, organic carbon (OC), cation exchange capacity (CEC), electrical conductivity (EC), soil microbial respiration (SMR), carbonate calcium equivalent (CCE), soil porosity (SP), bulk density (BD), exchangeable sodium percentage (ESP), mean weight diameter (MWD), available potassium (AK), total nitrogen (TN), available phosphorus (AP), available Fe (AFe), available Zn (AZn), available Mn (AMn), and available Cu (ACu). Mean wheat grain yield for the two years for all of the 100 sampling sites was also gathered. The SQIw was calculated using two weighting methods (FA and MLR) and maps were created using a digital soil mapping framework. The soil indicators taken in the minimum data set (MDS) were AK, clay, CEC, AP, SMR, and sand. The correlation between the MLR weighting technique (SQI-M) and the rainfed wheat yield (r=0.62) was slightly larger than that the correlation of yield with the FA weighted technique (SQI-F) (r=0.58). Results showed that the means of both SQI-M and SQI-F and rainfed wheat yield for Inceptisols were higher than for Entisols although these differences were not statistically significant. Both SQI-M and SQI-F showed that areas with Entisols had lower proportions of good soil quality grades (Grade I and II), and higher proportions of poor soil quality grades (Grade IV and V) compared to Inceptisols. Based on these results, soil type must be considered for soil quality assessment in future studies to maintain and enhance soil quality and sustainable production. The overall soil quality of the study region was of poor and moderate grades. To improve soil quality, it is therefore recommended that effective practices such as the implementation of scientific integrated nutrient management involving the combined use of organic and inorganic fertilizers in rainfed wheat fields be promoted.

Astroviruses (AstVs) are occurs globally and are common causes of gastroenteritis in human and animals. The genetic diversity and epidemiology of AstVs in Africa is not well known, hence, we aimed to genetically characterize astroviruses in asymptomatic smallholder piglets in East Africa. Twenty-four samples randomly selected from 446 piglets (<6 months old), initially collected for rotavirus study, was sequenced for metagenomic analysis. Thirteen (13/24) samples had contigs with high identity to genus Mamastrovirus. Analysis of 7 strains with complete (or near complete) genome revealed variable nucleotide and amino acid sequence identities with known PoAstV strains. The U083 and K321 strains had nucleotide sequence similarities ranging from 66.4 to 75.4 % to the known PoAstV2 strains, nucleotide sequence similarity of U460 strain with known PoAstV3 ranged 57.0 to 65.1 % to the, while K062, K366, K451, and K456 strains showed nucleotide sequence similarities of 63.5 to 80 % to the known PoAstV4 strains. The low sequence identities (<90 %) indicate that novel genotypes of PoAstVs are circulating in the study area. Multiple recombination events were detected in our PoAstV4 strains, indicating that the genetic diversity observed in these strains may be due to recombination. Importantly, we identified potential candidate epitopes with conserved peptides in our PoAstV strains that could aid in the design of immune diagnosis tools and subunit vaccines. Our data provide new intuitions into the genetic structure of porcine astroviruses in East African.

This study investigates the trend in monthly and annual rainfall, minimum and maximum temperature (T_min and T_max) using the Mann–Kendall (MK) test and Sen’s slope (SS) method and evaluates the significance of their variability for maize, sorghum and millet yields in northern Togo employing multiple regression analysis. The historical data of Kara, Niamtougou, Mango and Dapaong weather stations from 1977 to 2012 were used. Four non-parametric methods—Alexandersson’s Standard Normal Homogeneity Test (SNHT), Buishand’s Range Test (BRT), Pettitt’s Test (PT) and Von Neumann’s Ratio Test (VNRT)—were applied to detect homogeneity in the data. For the data which were serially correlated, a modified version of the MK test (pre-whitening) was utilised. Results showed an increasing trend in the annual rainfall in all four locations. However, this trend was only significant at Dapaong (p < 0.1). There was an increasing trend in T_max at Kara, Mango and Niamtougou, unlike Dapaong where T_max revealed a significant decreasing trend (p < 0.01). Similarly, there was an increasing trend in T_min at Kara, Mango and Dapaong, unlike Niamtougou where T_min showed a non-significant decreasing trend (p > 0.05). Rainfall in Dapaong was found to have increased (7.79 mm/year) more than the other locations such as Kara (2.20 mm/year), Niamtougou (4.57 mm/year) and Mango (0.67 mm). T_max increased by 0.13, 0.13 and 0.32 °C per decade at Kara, Niamtougou and Mango, respectively, and decreased by 0.20 per decade in Dapaong. Likewise, T_min increased by 0.07, 0.20 and 0.02 °C per decade at Kara, Mango and Dapaong, respectively, and decreased by 0.01 °C per decade at Niamtougou. Results of multiple regression analysis revealed nonlinear yield responses to changes in rainfall and temperature. Rainfall and temperature variability affects rainfed cereal crops production, but the effects vary across crops. The temperature has a positive effect on maize yield in Kara, Niamtougou and Mango but a negative effect on sorghum in Niamtougou and millet in Dapaong, while rainfall has a negative effect on maize yield in Niamtougou and Dapaong and millet yield in Mango. In all locations, rainfall and temperature variability has a significant effect on the cereal crop yields. There is, therefore, a need to adopt some adaptation strategies for sustainable agricultural production in northern Togo.

Conditional heteroskedastic financial time series are commonly modelled by (G)ARCH processes. ARCH(1) and GARCH were recently established in C[0,1] and L^2[0,1]. This article provides sufficient conditions for the existence of strictly stationary solutions, weak dependence and finite moments of (G)ARCH processes for any order in C[0,1] and L^p[0,1]. It deduces explicit asymptotic upper bounds of estimation errors for the shift term, the complete (G)ARCH operators and the projections of ARCH operators on finite-dimensional subspaces. The operator estimaton is based on Yule-Walker equations, and estimating the GARCH operators also involves a result estimating operators in invertible linear processes being valid beyond the scope of (G)ARCH. Moreover, our results regarding (G)ARCH can be transferred to functional AR(MA).

We use a system biology approach to translate the interaction of Bacillus Calmette-Gurin (BCG) + interleukin 2 (IL-2) for the treatment of bladder cancer into a mathematical model. The model is presented as a system of differential equations with the following variables: number of tumor cells, bacterial cells, immune cells, and cytokines involved in the tumor-immune response. This work investigates the delay effect induced by the proliferation of tumor antigen-specific effector cells after the immune system destroys BCG-infected urothelium cells following BCG and IL-2 immunotherapy in the treatment of bladder cancer. For the proposed model, three equilibrium states are found analytically. The stability of all equilibria is analyzed using the method of Lyapunov functionals construction and the method of linear matrix inequalities (LMIs).

Genomic selection (GS) can accelerate variety improvement when training set (TS) size, and its relationship with the breeding set (BS) are optimized for prediction accuracies (PA) of genomic prediction (GP) models. Sixteen GP algorithms were run on phenotypic best linear unbiased predictors (BLUPs) and estimators (BLUEs) of resistance to both fall armyworm (FAW) and maize weevil (MW) in a tropical maize panel. For MW resistance, 37% of the panel was the TS, and BS was the remainder whilst for FAW, random-based training sets (RBTS) and pedigree-based training sets (PBTS) were designed. PAs achieved with BLUPs varied from 0.66 to 0.82 for MW resistance traits, and, for FAW resistance, 0.694 to 0.714 for RBTS of 37%, and 0.843 to 0.844 for RBTS of 85%, and, these were at least two-fold those from BLUEs. For PBTS, FAW resistance PAs were generally higher than those for RBTS, except for one dataset. GP models generally showed similar PAs across individual traits whilst the TS designation was determinant since a positive correlation (R=0.92***) between TS size and PAs was observed for RBTS and, for the PBTS, it was negative (R=0.44**). This study pioneers the use of GS for maize resistance to insect pests in sub-Saharan Africa.

In this manuscript, we present a high-fidelity physics-based truth model of a Single Machine Infinite Bus (SMIB) system. We also present reduced-order control-oriented nonlinear and linear models of a synchronous generator-turbine system connected to a power grid. The reduced-order control-oriented models are next used to design various control strategies such as: proportional-integral-derivative (PID), linear-quadratic regulator (LQR), pole placement-based state feedback, observer-based output feedback, loop transfer recovery (LTR)-based linear-quadratic-Gaussian (LQG), and nonlinear feedback-linearizing control for the SMIB system. The controllers developed are then validated on the high-fidelity physics-based truth model of the SMIB system. Finally, a comparison is made of the performance of the controllers at different operating points of the SMIB system.

This paper is a slightly modified, abridged version of a previous work "Parametric Gevrey asymptotics in two complex time variables through truncated Laplace transforms'' motivated by our contribution in the conference "Formal and Analytic Solutions of Diff. (differential, partial differential, difference, q-difference, q-difference-differential) Equations on the Internet'' (FASnet20). It aims to clarify and give further detail at some crucial points concerning the asymptotic behavior of the solutions of the problems studied in that work.

Introduced in 2009, Bitcoin has demonstrated a huge potential as the world’s first digital currency and has been widely used as a financial investment. Our research aims to uncover the relationship between Bitcoin prices and people’s sentiments about Bitcoin on social media. Among various social media platforms, micro-blogging is one of the most popular. Millions of people use micro-blogging platforms to exchange ideas, broadcast views, and to provide opinions on different topics related to politics, culture, science, and technology. This makes them a potentially rich source of data for sentiment analysis. Therefore we chose one of the busiest micro-blogging platforms, Twitter, to perform sentiment analysis on Bitcoin. We used ELMo embedding model to convert Bitcoin-related tweets into a vector form and SVM classifier to divide the tweets into three sentiment categories - positive, negative, and neutral. We then used the sentiment data to find its relation with Bitcoin price fluctuation using the linear mixed model.

Introducing children to sustainable and healthy school meals can promote a long-term dietary shift to lower climate impact and improve population health. The aim of the OPTIMAT study was to optimize meals for minimum deviation from the current food supply while reducing greenhouse gases and ensuring nutritional adequacy without increasing cost. Optimized menus were tested in four primary schools in Sweden and effects on daily food consumption and waste evaluated. Pupils received their usual menu plan for three weeks and then the isocaloric optimized menu plan for another three weeks. Nutritional recommendations for a school lunch and a maximum of 500 grams of CO2eq/meal were applied as constraints during linear programming. Pulses, Cereals, Meat and Eggs increased, while Fats and Oils, Dairy, Sauces and Seasonings decreased. The amount of ruminant meat was reduced in favor of other meat products. The new menu was 28% lower in greenhouse gas emissions and slightly less costly than the original. No significant changes in mean food consumption or plate waste were found in interrupted time series analysis between the two periods. This pragmatic approach for combining linear optimization with meal planning could accelerate sustainable development of the meal sector in Sweden and abroad.

Near-fault ground motions can cause severe damage to civil structures, including bridges. Safety assessment of these structures for near fault ground motion is usually performed through Non-Linear Dynamic Analyses, while faster methods are often used. IMPAb (Incremental Modal Pushover Analysis for Bridges) permits to investigate the seismic response of a bridge by considering the effects of higher modes, which are often relevant for bridges. In this work, IMPAb is applied to a bridge case study considering near-fault pulse-like ground motion records. The records were analyzed and selected from the European Strong Motion Database and the pulse parameters were evaluated. In the paper results from standard pushover procedures and IMPAb are compared with nonlinear Response-History Analysis (NRHA), considering also the vertical component of the motion, as benchmark solutions and incremental dynamic analysis (IDA). Results from the case study demonstrate that the vertical seismic action has a minor influence on the structural response of the bridge. Therefore IMPAb, which can be applied considering vertical motion, remains very effective conserving the original formulation of the procedure, and can be considered a well performing procedure also for near-fault events.

Electrode is a key component in a microbial electrolysis cell (MEC) and it needs significant improvement for practical implementation of MEC. For effective development of electrode technology, accurate and reproducible analytical methods are very important. Linear sweep voltammetry (LSV) is an essential analytical method for evaluating electrode performance; however, it has not been firmly established yet in the MEC field. In this study, biological brush (BB), abiotic brush (AB), Pt wire (PtW), stainless steel wire (SSW) and mesh (SSM)) were tested to explore the most suitable counter electrode in different medium conditions. Coefficient of variation (CV) for Imax of LSV were comparatively analyzed. In BB-anode LSV, SSW (0.48%) and SSM (2.17%) showed higher reproducibility as a counter electrode. In SSM-cathode LSV, BB (1.76%) and PtW (2.01%) produced more reproducible results. In the Ni-AC-SSM-cathode LSV, PtW (3.54%) and BB (8.81%) produced more reproducible result. It shows electrode used in the operation is an appropriate counter electrode in the acetate-added condition. However, in the absence of acetate, PtW (1.24%) and BB (1.71%) produced more reproducible results in SSM cathode and PtW (0.61%) and SSW (1.21%) did in the Ni-AC-SSM-cathode, showing PtW is an appropriate counter electrode. These results also shows that PtW is an appropriate counter electrode in cathode LSV.

In this paper, a 3 DOF gyrscope position control have been designed and controlled using optimal control theory. An input torque has been given to the first axis and the angular position of the second axis have been analyzed while the third axis are kept free from rotation. The system mathematical model is controllable and observable. Linear Quadratic Integral (LQI) and Linear Quadratic State Feedback Regulator (LQRY) controllers have been used to improve the performance of the system. Comparison of the system with the proposed controllers for tracking a desired step and random angular position have been done using Matlab/Simulink Toolbox and a promising results has been analyzed.

We present a new mathematical model of disease spread reflecting specialties of covid-19 epidemic by elevating the role social clustering of population. The model can be used to explain slower approaching herd immunity in Sweden, than it was predicted by a variety of other mathematical models; see graphs Fig. \ref{GROWTH2}. The hierarchic structure of social clusters is mathematically modeled with ultrametric spaces having treelike geometry. To simplify mathematics, we consider homogeneous trees with $p$-branches leaving each vertex. Such trees are endowed with algebraic structure, the $p$-adic number fields. We apply theory of the $p$-adic diffusion equation to describe coronavirus' spread in hierarchically clustered population. This equation has applications to statistical physics and microbiology for modeling {\it dynamics on energy landscapes.} To move from one social cluster (valley) to another, the virus (its carrier) should cross a social barrier between them. The magnitude of a barrier depends on the number of social hierarchy's levels composing this barrier. As the most appropriate for the recent situation in Sweden, we consider {\it linearly increasing barriers.} This structure matches with mild regulations in Sweden. The virus spreads rather easily inside a social cluster (say working collective), but jumps to other clusters are constrained by social barriers. This behavior matches with the covid-19 epidemic, with its cluster spreading structure. Our model differs crucially from the standard mathematical models of spread of disease, such as the SIR-model. We present socio-medical specialties of the covid-19 epidemic supporting our purely diffusional model.

A vast majority of the countries is under the economic and health crises due to the current epidemic of coronavirus disease 2019 (COVID-19). The present study analyzes the COVID-19 using time series, which is an essential gizmo for knowing the enlargement of infection and its changing behavior, especially the trending model. We have considered an autoregressive model with a non-linear time trend component that approximately converted into the linear trend using the spline function. The spline function split the COVID-19 series into different piecewise segments between respective knots and fitted the linear time trend. First, we obtain the number of knots with its locations in the COVID-19 series and then the estimation of the best-fitted model parameters are determined under Bayesian setup. The results advocate that the proposed model/methodology is a useful procedure to convert the non-linear time trend into a linear pattern of newly coronavirus case for various countries in the pandemic situation of COVID-19.

This paper reviews the unilateral and bilateral, one- and two-dimensional Laplace transforms. The unilateral and bilateral Laplace transforms are compared in the one-dimensional case, leading to the formulation of the initial-condition theorem. This problem is solved with all generality in the one- and two-dimensional cases with the bilateral Laplace transform. General two-dimensional linear systems are introduced and the corresponding transfer function defined.

We present a model of infection dynamics that might explain slower approaching the herd immunity during the covid-19 epidemy in Sweden than it was predicted by a variety of other models; see graphs Fig. \ref{GROWTH2}. The new model takes into account the hierarchic structure of social clusters in the human society. We apply the well developed theory of random walk on the energy landscapes represented mathematically with ultrametric spaces. This theory was created for applications to spin glasses and protein dynamics. To move from one social cluster (valley) to another, the virus should cross a social barrier between them. The magnitude of a barrier depends on the number of social hierarchy's levels composing this barrier. As the most appropriate for the recent situation in Sweden, we consider linearly increasing (with respect to hierarchy's levels) barriers. This structure of barriers matches with a rather soft regulations imposed in Sweden in March 2020. In this model, the infection spreads rather easily inside a social cluster (say working collective), but jumps to other clusters are constrained by social barriers. This model's feature matches with the real situation during the covid-19 epidemy, with its cluster spreading structure. Clusters need not be determined solely geographically, they are based on a number of hierarchically ordered social coordinates. The model differs crucially from the standard models of spread of disease, such as the SIR-model. Our model describes such a specialty of spread of covid-19 virus as the presence of ``super-infectors'' who by performing a kind of random walk on a hierarchic landscape of social clusters spreads infection. In future, this model will be completed by adding the SIR-type counterpart. But, the latter is not a specialty of covid-19 spreading.

The main goal of this article is to demonstrate the impact of environmental data on the spreading of Covid-19. In this research, data has been collected from 70 cities/provinces that are affected by Covid-19. Here, environmental data refers to temperatures, humidity and population density in each of these cities/provinces. This data has been analyzed using statistical models such as Poisson, Quasi-Poisson and negative Binomial. It is found that a negative Binomial regression model is the best fit for our data. Our results reveal that average high temperature is the vital factor to slow down the spread of Covid-19. In addition, higher population density found to be an important factor for the quick spreading of Covid-19 where it is quite impossible to maintain the social distance and the virus can spread easily.

This paper presents the application of optimal control problem in modeling of stirred tank heater temperature control. The analysis of the open loop system shows that the system is not efficient without a controller. Linear Quadratic Gaussian (LQG) and Linear Quadratic Integral (LQI) controllers are used to increase the performance of the system. Comparison of the closed loop system with the proposed controllers have been done with Matlab/Simulink Toolbox and a promising results have been analyzed.

To obtain an accurate and reproducible experimental results in microbial fuel cell (MFC), it is important to know ‘anode maturation biofilm’ to produce a stable and maximum performance. For this purpose, four single chamber MFCs were tested in this study. The linear sweep voltammetry (LSV) polarization tests illustrated that maximum power densities of three MFCs became stable after 9 weeks. Although there were variations afterwards, such variations were negligible. Average maximum power densities from the 9th to the 17th week were 2,990 mW/m2 (MFC-4), 2,983 mW/m2 (MFC-2), 2,368 mW/m2 (MFC-3) and 837 mW/m2 (MFC-1). Polarization resistance shows that MFC-1 had much larger anode resistance (36.6-85.4 Ω) than the other MFCs (1.7-11.6 Ω). Anodic cyclic voltammetry (CV) shows that current production increased over time and MFC-1 had much smaller current production (24.4 mA) than the other MFCs (31.0-34.9 mA) at 17th week. The increased current production indicates anode biofilm became more mature over time, but overall cell performance did not increased accordingly. Possibly due to the bad inoculation, MFC-1 showed the lowest performance. However, its performance was restored to the initial performance and anode resistance was reduced by 47% at 17th week. This study shows that the optimum anode maturation time is 9 weeks and that bioanode performance is a key factor for MFC performance. This study also shows than LSV polarization and CV tests are accurate and non-destructive measurement methods for diagnosing anode performance.

In this paper, modelling design and analysis of a triple inverted pendulum have been done using Matlab/Script toolbox. Since a triple inverted pendulum is highly nonlinear, strongly unstable without using feedback control system. In this paper an optimal control method means a linear quadratic regulator and pole placement controllers are used to stabilize the triple inverted pendulum upside. The impulse response simulation of the open loop system shows us that the pendulum is unstable. The comparison of the closed loop impulse response simulation of the pendulum with LQR and pole placement controllers results that both controllers have stabilized the system but the pendulum with LQR controllers have a high overshoot with long settling time than the pendulum with pole placement controller. Finally the comparison results prove that the pendulum with pole placement controller improve the stability of the system.

In this paper, an electromechanical mass lifter system is designed, analyzed and compare using optimal and robust control theories. LQR and μ -synthesis controllers are used to improve the lift displacement by comparison method for tracking the desired step and sinusoidal wave signals input. Finally, the comparison simulation result prove the effectiveness of the electromechanical mass lifter system with μ -synthesis controller for improving the rise time, percentage overshoot, settling time and peak value of tracking the desired step displacement signal and improving the peak value for tracking the desired sinusoidal displacement signal with a good performance.

From the linear Nash-Green fluctuations of background metric, we present the perturbation equations in an embedded four space-time. In the context of a five-dimensional bulk, we show that the perturbations are only propagated by the gravitational tensorial field equation. In a Newtonian conformal gauge, we study the matter density evolution in sub-horizon regime and on how such scale may be affected by the extrinsic curvature. We use the "extended Gold 2018'' growth dataset with 25 datapoints and the best fit Planck2018/LambdaCDM parameters. Hence, we determine the evolution equation for the density growth delta(a) as a result from the embedded equations of the background geometry. By using solar constraints, we analyse the evolution of the effective Newtonian constant G_eff and showing that applying Taylor expansion to G_eff (a) under the constraint of time-derivative of G_eff(0)=G at a= 1 in matter domination era, we get an agreement with Big Bang Nucleosynthesis (BBN) and also an alleviation of the 3-sigma tension to 1-sigma contour between (sigma8-Omega_m) of the observations from Cosmic Microwave Background (CMB) and Large Scale Structure (LSS) probes.

Although phylogenetic analysis shows coronaviruses (CoV) share similar genome sequences, CoVs encode different number of proteins (5 to 14), which has implication on viral pathogenicity and infection. Here, we aimed to identify (in-silico) the similarities between different members of coronavirus family. The analysis included 50 coronavirus proteomes, including SARS-CoV-2 (COVID-19), to find the variation of the number of protein functional motifs and domain in each coronavirus. For this role, we used the experimentally validated domain (motif) that known to be crucial for viral infection. Although human CoVs are classified within one genus, we found variations among them. SARS-CoV-1, SARS-CoV-2 and MERS-CoV encode different type of domains, which has implications on the molecular interactions triggered by each virus within human cells. Secondly, we used functional motifs to reconstruct the potential molecular pathways or interactions triggered by SARS-CoV-2 proteins within human cell.