We have experimentally analyzed multi-azimuth degradation mechanisms that govern failures of commercially-available high-power (1 Watt) phosphor-coated white (hppc-W) light-emitting diodes (LEDs) covered with peanut-shaped lens under three current-stress aging (CSA) conditions. Comprehensive analyses focus on photometric, chromatic, electrical, thermal, and packaging characteristics. At the packaging level, (a) the decrease of the phosphor-conversion efficiency, (b) the yellow-browning of the optical lens, and (c) the darkening of the silver-coated reflective layer deposited with extraneous chemical elements (e.g., C, O, Si, Mg, and Cu, respectively) contribute collectively to the integral degradation of the optical power. By contrast, Ohmic contacts, thermal properties, and angles of maximum intensity remain unchanged after 3840 h aging in three cases. Particularly at the chip level, the formation of point defects increases the number of non-radiative recombination centers, and thus decreases the optical power during aging stages. Nevertheless, in view of the change of the ideality factor, the dopant activation and the annealing effect facilitate the increase of the optical power in two specific aging stages (192 h∼384 h and 768 h∼1536 h), respectively. This work offers a systematic guidance for the development of reliable LED-based light sources in general-lighting areas.

Outdoor lighting is becoming increasingly widespread, and residents are suffering from serious light pollution as a result. Residents’ awareness of their rights to protection has gradually increased. However, due to the sometimes-inaccessible nature of residential vertical light incidence intensity data and the high cost of obtaining specific measurements, there is no appropriate hierarchic compensation for residents suffering from different degrees of light pollution. It is therefore important to measure light pollution levels and their damage at the neighborhood scale to provide residents with basic materials for proper protection and to create more politically suitable solutions. This article presents a light pollution assessment method that is easy to perform, is low-cost, and has a short data-processing cycle. This method can be used to monitor residential zone light pollution in other cities. We chose three open areas to test the spatial variation pattern of light intensity. The results are in accordance with spatial interpolation patterns and can be fit, with high precision, using the IDW method. This approach can also be used in 3 dimensions to quantitatively evaluate the distribution of light intensity distribution. We use a mixed-use zone in Beijing known as The Place as our case study area. The vertical illumination at the windows of residential buildings ranges from 2 lux to 23 lux; the illumination in some areas is far higher than the value recommended by CIE. Such severe light pollution can seriously interfere with people's daily lives and has a serious influence on their rest and health. The results of this survey will serve as an important database to assess whether the planning of night-time lighting is scientific and whether it provides residents with a basis for the protection of their rights.

Crystallization of glass through conventional thermal annealing in a furnace is a well-understood process. However, crystallization by femtosecond (fs) laser brings another dimension to this process. The pulsed nature of the irradiation necessitates a reevaluation of parameters for optimal crystallization and to understand the particularities in the case of using fs laser. This includes adjusting the laser pulse energy, the repetition rate, and the writing speed to either initiate nucleation or achieve substantial crystal growth. Therefore, a key challenge to this work is to establish reliable calculations for understanding the relation of the size of the crystallized region with respect to an ongoing transition (e.g., solid-to-solid, liquid-to-solid), and accounting for the aforementioned laser parameters. In this context and based on previous work, we simulate a temperature distribution (in space and time) to model the thermal treatment at any point in the glass. By setting the condition that the temperatures are between the glass transition and melting temperature, we can deduce the crystallized region size to be compared with experimental observations. For that purpose, the knowledge of the beam width at the focal point and of the absorbed beam energy fraction are critical inputs that were extracted from experiments found in the literature. After that, management of the crystallization process and the width of the crystallization line can be achieved according to pulse energy e.g. crystallite size, and also the effect of the scanning speed can be understood. Among the main conclusions to highlight, we disclose the laser conditions that determine the extent of the crystallized area and deduce that it is never interesting to increase the pulse energy too much but rather the repetition rate for uniform crystallized line.

Mechanical ventilation (MV), used in patients with acute lung injury (ALI), induces diaphragmatic myofiber atrophy and contractile inactivity, termed ventilator-induced diaphragm dysfunction. Phosphoinositide 3-kinase- (PI3K-) is crucial in modulating fibrogenesis during the reparative phase of ALI; however, the mechanisms regulating the interactions among MV, myofiber fibrosis, and PI3K- remain unclear. We hypothesized MV with or without bleomycin treatment would increase diaphragm muscle fibrosis through the PI3K- pathway. Five days after receiving a single bolus of 0.075 units bleomycin intratracheally, C57BL/6 mice were exposed to 6 or 10 mL/kg MV for 8 h after receiving 5 mg/kg of AS605240 intraperitoneally. In wild-type mice, bleomycin exposure followed by MV 10 mL/kg prompted significant increases in disruptions of diaphragmatic myofibrillar organization, transforming growth factor-1, oxidative loads, Masson’s trichrome staining, extracellular collagen levels, positive staining of -smooth muscle actin, PI3K- expression, and myonuclear apoptosis (P < 0.05). Decreased diaphragm contractility and peroxisome proliferator activated receptor- coactivator-1 levels were also observed (P < 0.05). MV-augmented bleomycin-induced diaphragm fibrosis and myonuclear apoptosis were attenuated in PI3K-γ-deficient mice and through AS605240-induced inhibition of PI3K- activity (P < 0.05). MV-augmented diaphragm fibrosis after bleomycin-induced ALI is partially mediated through PI3K-γ. Therapy targeting PI3K-γ may ameliorate MV-associated diaphragm fibrosis.

Luminescent carbon dots (CDs) were locally synthesized in the core of CYTOP fibers using IR femtosecond laser direct writing (FLDW), a one-step simple method serving as a post-treatment of the genuine fiber. This approach enables the creation of several types of modifications such as ellipsoid voids. The CDs and photoluminescence (PL) distribute at the periphery of the voids. The PL spectral properties were studied through Excitation Emission Matrix in the visible range and excitation/emission spectrum in UV/visible range. Our finding reveals the presence of at least 3 distinct luminescent species, facilitating a broad excitation range extending from UV to green, and light emission spanning from blue to red. The average laser power and dose influence the quantity and ratio of these luminescent CD species. Additionally, we measured the spatially resolved lifetime of the luminescence during and after the irradiation. We found longer lifetimes at the periphery of the laser-induced modified regions and shorter ones closer to the center, with a dominant lifetime ~ 2ns. Notably, unlike many other luminophores, these laser-induced CDs are insensitive to oxygen, enhancing their potential for display or data storage applications.

In this study, we define screening maps for Italy that classify sites based on their potential for triggering landslides. To this end, we analyze seismic hazard maps and hazard disaggregation results on a national scale considering four spectral periods (0.01s, 0.2s, 0.5s, and 1.0s) and three return periods (475, 975, and 2475 years). First, joint distributions of magnitude (M) and distance (R) from hazard disaggregation are analyzed by means of an innovative approach based on image processing techniques to find all modal scenarios contributing to the hazard. In order to obtain the M-R scenarios controlling the triggering of earthquake-induced landslides at any computation node, mean and modal M-R pairs are compared to empirical curves defining the M-R bounds associated with landslide triggering. Three types of landslides are considered (i.e., disrupted slides and falls, coherent slides, and lateral spreads and flows). As a result, screening maps for all of Italy showing the potential for triggering landslides based on the level of seismic hazard are obtained. The maps and the related data are freely accessible at the following web address: https://distav.unige.it/rsni/slideq.php.

Introduction: Substance-induced psychotic disorder (SIPD) is a mental health condition linked to the use of a psychotropic substance whose pathogenesis has not been totally clarified. The present retrospective observational study has the objective to identify differences in clinical features and peripheral biomarkers in SIPD patients according to the main substance of abuse.Methods: A total sample of 218 patients was divided in 3 groups according to the type of consumed substance: alcohol, cannabis and psychostimulants. The 3 groups were compared for continuous variables by one-way analyses of variance (ANOVAs) and for qualitative variables by χ² tests. After removing alcohol-induced psychotic disorder group, the same analyses were repeated. Statistically significant variables from these latter analyses were included in a binary logistic regression model to confirm their reliability as predictors for cannabis- or psychostimulants-induced psychotic disorders. Results: Psychotic cannabis abusers were younger (p<0.01) and had an earlier age at onset (p<0.01). On the contrary, alcohol consumers resulted to have a longer duration of illness (p<0.01), more previous hospitalizations (p=0.04), more frequent medical comorbidity (p<0.01), higher mean Modified Sad Person Scale scores (p<0.01). Finally, psychostimulant abusers had more frequently a lifetime history of poly-substance use disorders (p<0.01). Binary logistic regression revealed that higher mean Brief Psychiatric Rating Scale scores (p<0.01) higher sodium (p=0.012) and haemoglobin(p=0.040) plasma levels were predictors of cannabis misuse in SIPD patients.Conclusions: Different clinical factors and biochemical parameters con be associated to SIPD according to the main substance of abuse, thus requiring a specific management by clinicians.

Modern engineering faces challenges in ensuring technical standards for service, durability, and sustainability. Political, administrative, and budgetary factors, coupled with climate change, pose tasks to structural integrity, affecting industries and economies. Marine infrastructures represent a strategic asset of the country as it handles a large part of the economic exchanges. This article analyzes five essential factors that play a fundamental role in the performance analysis of coastal structures: Chloride-induced corrosion, degradation models, maintenance strategies, monitoring, and climate change. Starting with reinforcement corrosion, considered as the main cause of distress, particularly in coastal zones for the long-term behavior of structures. Additional pressure from the influences of climate change is becoming evident and extreme, leading to reduction in capacity. To guarantee the lifespan, degradation models contribute by estimating the long-term performance of the asset as a strategic piece to the development of effective maintenance solutions. Additionally, quantifying the condition of the structure from monitoring data, plays a crucial part that provides information on the current situation of the structure. Finally, this review summarizes the challenges associated with the maintenance of aging marine structures considering aspects such as corrosion, monitoring, and the future challenges this area will face due to climate change.

2,4-dichlorophenoxyacetic acid (2,4-D) is a globally used herbicide and is frequently found in water samples. This fact has prompted studies on its effects in non-target organisms, revealing significant alterations on liver structure and function. In this review, we evaluated the literature on the hepatotoxicity of 2,4-D, focusing on morphological damages, biomarkers of toxicity and affected liver functions. Searches were conducted on PubMed, Web of Science and Scopus and 83 articles were selected after curation. Among the studies, 72% used in vivo models and 30% used in vitro models. Additionally, 48% used the active ingredient, and 35% used commercial formu-lations in exposure experiments. The most affected biomarkers were related to a decrease in an-tioxidant capacity, including alterations in the activities of catalase and superoxide dismutase, and in the levels of malondialdehyde. Changes in energy metabolism, lipids, liver function, and xenobiotic metabolism were also identified. Furthermore, we found studies about the effects of 2,4-D in mixtures with other pesticides, as well as hepatoprotection trials. The reviewed data in-dicate that the reduction in antioxidant capacity and oxidative stress play an important role in 2,4-D-induced hepatotoxicity. However, the mechanism of action of the herbicide is still not ful-ly understood and further research in this area is needed.

Photodynamic therapy (PDT) has garnered significant attention in the fields of cancer treatment and drug-resistant bacteria eradication due to its non-invasive nature and spatiotemporal controllability. Iridium complexes have captivated researchers owing to their tunable structure, exceptional optical properties, and substantial Stokes displacement. However, most of these complexes suffer from aggregation-induced quenching, leading to diminished luminous efficiency. In contrast to conventional photosensitizers, photosensitizers exhibiting aggregation-induced luminescence (AIE) properties retain the ability to generate a large number of reactive oxygen species when aggregated. To overcome these limitations, we designed and synthesized a novel iridium complex named Ir-TPA in this study. It incorporates quinoline triphenylamine cyclomethylated ligands that confer AIE characteristics for Ir-TPA. We systematically investigated the photophysical properties, AIE behavior, spectral features, and reactive oxygen generation capacity of Ir-TPA. The results demonstrate that Ir-TPA exhibits excellent optical properties with pronounced AIE phenomenon and robust capability for producing singlet oxygen species. This work not only introduces a new class of metal iridium complex photosensitizer with AIE attributes but also holds promise for achieving remarkable photodynamic therapeutic effects in future cellular experiments and biological studies.

Transit-oriented development (TOD), such as metro depot and over-track building complexes, has expanded rapidly in China. Over-track building construction has the advantage of comprehensive utilization of land resources, ease of commuting to work, and provide funds for subway construction. However, there still has a pending problem, disturbance of railway vibration, for TOD. Excessive noise and vibration seriously affect people’s life. To address this challenge, field measurements are used to obtain the vibration source characteristics and vibration propagation of the ground and the superstructure in this study. And the typical metro depot with over-track building in Wuhan was selected. The effects of vibration on the surrounding ground and adjacent buildings caused by the operation of trains have been measured, and the propagation law of train-induced ground vibration acceleration in the time and frequency domains has been analyzed. The distribution and propagation laws of vibration noise, structural noise and secondary structure noise in sensitive areas such as the throat area, depot area, test section and access section of the over-track buildings and their impact laws on the over-track buildings are obtained. And the effectiveness of the vibration and noise reduction methods used were evaluated. Results show that within 43 m from the train running track, the train running induced vertical vibration acceleration level in the high-rise building peak size of 58.8 dB, the average value of 55.62 dB; vibration frequency components are mainly 40-60 Hz. The findings might provide useful insight for designing vibration mitigation systems in new metro depots with over-track buildings.

Target pests of genetically engineered crops producing both defensive allelochemicals and Bacillus thuringiensis (Bt) toxins often sequentially or simultaneously uptake allelochemicals, Bt toxins, and/or insecticides. How the three types of toxins interact to kill pests remains underexplored. Here we investigated the interactions of Bt toxin Vip3A, plant allelochemical flavone, and insecticide emamectin benzoate in Spodoptera frugiperda. Simultaneous administration of flavone LC25 + Vip3A LC25, emamectin benzoate LC25 + Vip3A LC25, and flavone LC15 + emamectin benzoate LC15 + Vip3A LC15 but not flavone LC25 + emamectin LC25 yielded a mortality significantly higher than their expected additive mortality (EAM). One-day preexposure to one toxin at LC5 followed by 6-day exposure to the same toxin at LC5 plus another toxin at LC50 showed that the mortality of flavone LC5 + Vip3A LC50, emamectin benzoate LC5 + Vip3A LC50, and Vip3A LC5 + emamectin benzoate LC50, were significantly higher than their EAM, while that of flavone LC5 + emamectin benzoate LC50 was significantly lower than their EAM. No significant difference existed among the mortalities of Vip3A LC5 + flavone LC50, emamectin benzoate LC5 + flavone LC50, and their EAMs. The results suggest that the interactions of the three toxins are largely synergistic (inductive) or additive, depending on their combinations and doses.

This paper deals with the quantitative analysis of measured fracture-induced electromagnetic radiation (FEMR) in the vicinity of the Dead Sea Transform using the Angel-M1 instrument, which enables the recording of FEMR signals in a 3D manner. Results show both the possibility of estimating the sizes of micro-fractures that are the sources of the radiation, and of assessing the direction of their location to the measuring device and the range of magnitude Mw of the impending "events" (EQ's) associated with the present FEMR measurements. Moreover, the relation between the measured FEMR activity (the number of FEMR hits per unit time) and the FEMR event magnitudes shows consistency with the Gutenberg-Richter relationship for the region. Such measurements could therefore constitute a preliminary 'field reinforcement' towards an EMR valid method for a real earthquake forecast, which would provide much earlier warnings than the seismic ones. Obviously, the present observed FEMR measurements can only be used as an assessment of the stress concentration and micro-fracturing in the region since they relate to the very initial nucleation phase of a "virtual" (extremely low Richter scale value) earthquake, but they do provide the necessary feasibility test for a prediction method since all lab-measured FEMR features were confirmed also in the field.

Cotton (Gossypium spp.) is a major source of natural fiber and an important cash crop. The cotton growth habit and architecture determine its productivity and influence management strategies for commercial production. The GATA transcription factors (TFs) control various developmental processes in plants, such as flower, bract and embryo development, and petal differentiation. As stable transformation is still a bottleneck in many plant species, TRV-VIGS was used to manipulate gene expression in different plants, including Gossypium hirsutum L. In this study, we undertook the TRV-based VIGS to functionally characterize two candidate genes, Gohir.D05G103700 and Gohir.D12G153600, identified through the expression QTL analysis for five floral induction and meristem identity genes using the upland cotton mini-core collection. Virus-induced silencing of the Gohir.D05G103700 gene resulted in up to a 1.4-fold reduction in the transcript level in two inoculated plants, G3 and G4, and Gohir.D12G153600 gene resulted in up to a 2.3-fold reduction in transcript level in a single inoculated plant P05 relative to the mock-treated plant. The TRV2-Gohir.D05G103700 inoculated plants precisely G3 and G4 also exhibited loss of the supernumerary (fourth) floral bract in the squares, whereas the TRV2-Gohir.D12G153600 inoculated plants did not show any observable phenotypic change relative to the mock-treated plants.  Altogether, this study suggested that TRV-VIGS can be used to characterize genes in cotton relatively rapidly and the cotton Gohir.D05G103700 gene is a positive regulator of the indeterminate growth habit in cotton, which could be manipulated to obtain a cotton plant with architecture best suited for the cultivation area.

Heavy metal contamination is listed among the most alarming threats to the environment and human health. The detrimental effects of heavy metals in the natural environment span from a reduction of biodiversity to toxic effects on marine life - through microplastic born heavy metals -, to impairment of microbial activity in the soil, and to detrimental effects on animal reproduction. A host of different chemical and biological technologies have been proposed to alleviate environmental contamination by heavy metals. Relatively less attention has been paid to the microbial precipitation of heavy metals, as a side mechanism of the most general process of microbially induced calcite precipitation (MICP). This process is currently receiving a great deal of interest from both a theoretical and practical standpoint, because of its possible practical applications in concrete healing and soil consolidation, and its importance in the more general framework of microbial induced mineral precipitation. In this study, we analyse the ability of the marine bacteria Vibrio harveyi in co-precipitating CaCO3 minerals, together with Cd, Cr, Pb, and Zn added in form of nitrates, from solutions containing CaCl2. The precipitated carbonatic minerals were a function of the different heavy metals present in the solution. The process of co-precipitation appears to be rather effective and fast, as the concentrations of the 4 heavy metals were reduced in 2 days by 97.2%, on average, in the solutions.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article's main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

Direct cardiac reprogramming of fibroblasts into induced cardiomyocytes (iCMs) is a promising approach but remains a challenging technology of regenerative medicine for damaged myocardium. Efforts have been focused on improving the efficiency by understanding fundamental mechanisms. One of the major challenges is that the plasticity of cultured fibroblast varies batch to batch with unknown mechanisms. Here, we noticed that a portion of in vitro cultured fibroblasts have been activated to differentiate into myofibroblasts, marked by the expression of αSMA, even in the primary cell culture of tissues. Both forskolin, which activates adenylyl cyclase and increases cAMP concentration, and TGFbeta inhibitor SB431542 can efficiently suppress myofibroblast differentiation of cultured fibroblasts. However, SB431542 improved but forskolin blocked iCM reprogramming of fibroblasts that were infected with retroviruses of Gata4, Mef2c and Tbx5 (GMT). Moreover, inhibitors of cAMP downstream signaling pathways, PKA or CREB-CBP, significantly improved the efficiency of iCM reprogramming. Consistently, inhibition of p38/MAPK, another upstream regulator of CREB-CBP, also improved reprogramming efficiency. We then investigated if inhibition of these signaling pathways in primary cultured fibroblast could improve their plasticity for reprogramming, and found that preconditioning of cultured fibroblasts with CREB-CBP inhibitor significantly improved the cellular plasticity of fibroblasts to be reprogrammed, yielding ~2-fold amount of reprogrammed iCMs compared to that of untreated control cells. In conclusion, suppression of cAMP/PKA/CREB signaling axis improves fibroblast plasticity for direct cardiac reprogramming.

Regenerative medicine aims to repair damaged or missing cells, tissues or organs for the treatment of various diseases, poorly managed with conventional drugs and medical procedures. To date there are different approaches to obtain these results. Multimodal regenerative methods include transplant of healthy organs, tissues, or cells, body stimulation to activate a self healing response in damaged tissues, as well as the combined use of cells and bio-degradable scaffold to obtain functional tissues. Certainly, stem cells and derived products are promising tools in regenerative medicine due to their ability to induce de novo tissue formation and/or promote tissue and organ repair and regeneration. Currently, several studies have shown that the beneficial stem cell effects in damaged tissue restore are not depending on their engraftment and differentiation on the injury site, but rather to their paracrine activity. It is now well known that paracrine action of stem cells is due to their ability to release Extracellular Vesicles (EVs). EVs play a fundamental role in cell-to cell communication and are directly involved in tissue regeneration. In the present review, we tried to summarize the molecular mechanisms trough which EVs carry out their therapeutic action and their possible application for the treatment of several diseases.

In this paper, we consider the temporal development of the optical density of the H$_\alpha$ spectral line in a hydrogen laser induced plasma. This is achieved by using the so-called duplication method in which the spectral line is re-imaged onto itself and the ratio of the spectral line with it duplication is taken to its measurement without the duplication. We asses the temporal development of the self-absorption of the H$_\alpha$ line by tracking the decay of duplication ratio from its ideal value of 2. We show that when 20% loss is considered along the duplication optical path length, the ratio is 1.8 and decays to a value of 1.25 indicating an optically thin plasma grows in optical density to an optical depth of 1.16 by 400 ns in the plasma decay for plasma initiation conditions using Nd:YAG laser radiation at 120 mJ per pulse in a 1.11$\times10^{5}$ Pa hydrogen/nitrogen gas mixture environment. We also go on to correct the H$_\alpha$ line profiles for the self-absorption impact using two methods. We show that a method in which the optical depth is directly calculated from the duplication ratio is equivalent to standard methods of self-absorption correction when only relative corrections to spectral emissions are needed.

Pomegranate peel is a natural source of phenolics, claimed to possess healing properties, among which antioxidant and antidiabetic. In line with this evidence, the ethyl acetate PGE extract, obtained by Soxhlet from the peel of Dente di cavallo DC2 variety and characterized by a 4% amount of ellagic acid, has been studied for its hypoglycemic, antiglycation and antioxidative cytoprotective properties, in order to support a possible further nutraceutical interest. The α-amylase and α-glucosidase enzyme inhibition, interference with advanced glycation end-products (AGE) formation and metal chelating abilities were evaluated as hypoglycemic mechanisms. Also, considering that oxidative stress is associated with hyperglycemia complications, PGE antioxidant cytoprotective properties under hyperglycemic conditions were assayed. Phenolic profile was characterized by integrated chromatographic and spectrophotometric methods. Under our experimental conditions, PGE strongly inhibited the tested enzymes, especially α-glucosidase, and exerted chelating and antiglycation properties. Also, it reduced both ROS and GSH levels under hyperglycemic conditions, thus suggesting its ability to support cell functions by counteracting intracellular oxidative stress. Along with ellagic acid, rutin was the major identified flavonoid (about 4 %) of PGE. Present results suggest PGE to be a possible remedy for hyperglycemia management and encourage further studies to exploit its promising properties.

In intermediary metabolism, enzymes are mainly for the specific provision of one small molecule from another, B from A, for its further use. But there are also decades of work relating to another evolved purpose, which is to prevent untoward effects of odd compounds of various origins, and of ordinary intermediates, whose improper concentrations may be avoided by hydrolases and other activities of metabolic correction.

Background: In hepatocytes and alcohol-metabolizing cultured cells, Golgi undergoes ethanol (EtOH)-induced disorganization. Periniclear and organized Golgi is important in liver homeostasis, but how the Golgi remains intact is unknown. Work from our laboratories showed that EtOH-altered cellular function could be reversed after alcohol removal; we wanted to determine whether this recovery would apply to Golgi. Methods: We used alcohol-metabolizing HepG2 (VA-13) cells (cultured with or without EtOH for 72 h) and rat hepatocytes (control and EtOH-fed (Lieber-DeCarli diet). For recovery, EtOH was removed and replenished with control medium (48 hours for VA-13 cells) or control diet (10 days for rats). Results: EtOH-induced Golgi disassembly was associated with de-dimerization of the largest Golgi matrix protein giantin, along with impaired transport of selected hepatic proteins. After recovery from EtOH, Golgi regained their compact structure, and alterations in giantin and protein transport were restored. In VA-13 cells, when we knocked down giantin, Rab6a GTPase or non-muscle Myosin IIB, minimal changes were observed in control conditions, but post-EtOH recovery was impaired. Conclusions: These data provide a link between Golgi organization and plasma membrane protein expression and identify several proteins whose expression is important to maintain Golgi structure during the recovery phase after EtOH administration.

This work examines atomic and molecular signatures in laser-induced plasma in standard ambient temperature and pressure environments, including background contributions to the spectra that depend on the laser pulse-width. Investigations include solids, gases, and nano-particles. Abel inversions of measured line-of-sight data reveal insight into the radial plasma distribution. For nominal 6 nanosecond laser pulses and for pulse-energies in the range of 100 to 800 milli-Joules, expansion dynamics and turbulence due to shock phenomena are elucidated to address local equilibrium details that are frequently assumed in spatially averaged emission spectroscopy. Chemical equilibrium computations reveal temperature dependence of selected plasma species. Specific interests include atomic hydrogen (H) and cyanide (CN). The atomic H spectra, collected following optical breakdown in ultra-high-pure hydrogen and 9:1 mixtures of ultra-pure hydrogen and nitrogen gases, indicate spherical shell structures and isentropic expansion of the plasma kernel over and above the usual shockwave. The recombination radiation of CN emanates within the first 100 nanoseconds for laser-induced breakdown in a 1:1 CO₂:N₂ gas mixture when using nanosecond laser pulses to create the micro-plasma. The micro-plasma is generated using 1064 nm, 150 mJ, 6 ns Q-switched Nd:YAG laser radiation. Measurements of the optical emission spectra utilize a 0.64 m Czerny-Turner type spectrometer and an intensified charge-coupled device.

Background and objectives: Contrast-induced nephropathy (CIN), is an acute renal damage due to contrast agents. This study is conducted to determine the potential diagnostic value of hypoxia-inducible factor 2-alpha (HIF2-α) and to evaluate the renal protective effects of N-acetyl cysteine (NAC) and sildenafil in a rat CIN model. Material/Methods: This randomized, controlled, interventional animal study was conducted on Wistar rats. Totally, rats (n = 36) were randomly assigned to four groups: control (n = 9), CIN group (n = 9), CIN+NAC group (n = 9), and sildenafil (n = 9). The rat model was used to form iohexol-originated CIN. During the modelling, prophylactic treatment was performed at 24th and 48th hours. After 48 hours of the modelling; blood, urine, tissue samples were obtained for biochemical analyses. HIF-2-α levels were measured in renal tissue, serum and urine samples. Renal sections were performed in order for histopathologic and immunohistochemical evaluations. Results: In the CIN model, HIF-2α levels and other biochemical parameters were significantly increased (p < 0.01). Both sildenafil and NAC, efficiently decreased the renal damage due to contrast agents (p < 0.05). Similarly, after treatment with sildenafil and NAC, HIF-2α levels were significantly decreased (p < 0.05). Conclusions: The current study constructs an experimental base for the use of HIF-2α for clinical prevention and treatment of CIN. Several mechanisms may be postulated for the changes in HIF-2α levels. Besides, the increased HIF-2α levels with CIN and decreased HIF-2α levels after treatment may be used for the treatment and follow-up of patients with CIN.

Peripheral and autonomic neuropathy are common disease manifestations in systemic amyloidosis. Neurofilament light chain (NfL), a neuron-specific biomarker, is released into the blood and cerebrospinal fluid after neuronal damage. This systematic review provides an overview on the value of NfL in early detection of neuropathy, central nervous system involvement, monitoring of neuropathy progression, and treatment effect in systemic amyloidosis. A literature search in PubMed, Embase and Web of Science was performed on 14-02-2024 for studies investigating NfL levels in patients with systemic amyloidosis and transthyretin gene variant (TTRv) carriers. Only studies containing original data were included. Included were twelve full-text articles and six abstracts describing 1604 participants: 298 controls and 1306 TTRv carriers or patients with or without polyneuropathy. Patients with polyneuropathy demonstrated higher NfL levels compared to healthy controls and asymptomatic carriers. Disease onset was marked by rising NfL levels. Following initiation of transthyretin gene-silencer treatment, NfL levels decreased and remained stable over an extended period. NfL is not an outcome biomarker, but an early and sensitive disease process biomarker for neuropathy in systemic amyloidosis. Therefore, NfL has potential to be used for early detection of neuropathy, monitoring treatment effect, and monitoring disease progression in patients with systemic amyloidosis.

Heart failure (HF) is a life-threatening disorder and is treated by drug therapies and surgical interventions such as heart transplantation and left ventricular assist device (LVAD). However, these treatments can lack effectiveness in the long term and are associated with issues such as donor shortage in heart transplantation, and infection, stroke, or gastrointestinal bleeding in LVADs. Therefore, alternative therapeutic strategies are still needed. In this respect, stem cell therapy has been introduced for the treatment of HF and numerous preclinical and clinical studies using various types of stem cells, such as embryonic stem cells (ESCs) and induced pluripotent stem cells (iPSCs) have been shown to improve cardiac function and attenuate left ventricular remodeling. IPSCs, which have a capacity of unlimited proliferation and differentiation to cardiomyocytes, are a promising cell source for myocardial regeneration therapy. This review discusses the current status of cardiac regenerative therapy using iPSCs.

Pluripotent stem cells (PSCs) can differentiate into three germ layers and diverse autolo-gous cell lines. Being among the most commonly used large domesticated hoofed animals and serving as a vital source of food and bioreactors, cattle are among the many species in which PSCs have been developed. Bovine PSCs (bPSCs) are the "seed cells" of regenerative science and have immense potential to advance species propagation, genetic engineering, and disease treatment. Moreover, they can aid in screening new drugs for efficacy and toxicity, model human diseases, and establish a sustainable agricultural system that can cater to the needs of the growing global population. Establishing stable bPSCs in vitro has been a critical scientific challenge, and researchers have made numerous attempts to address this issue. This review primarily delves into the current research progress of bPSCs, the challenges faced, and their potential applications.

During geomagnetic storms, which are a result of solar wind interaction with the Earth’s magnetosphere, geomagnetically induced currents (GICs) begin to flow in the long-distance high-voltage power grids on the Earth’s surface. It causes a number of negative phenomena that affect the normal operation of the entire electric power system. To investigate the nature of the phenomenon and its possible effects on transformers, a GIC monitoring system was created in 2011, the devices of which were installed at five substations of the Kola-Karelian power transit in northwestern Russia. Over 12 years of operating the system a large amount of data has been accumulated, which cannot be analyzed manually within a reasonable amount of time. To analyze the constantly growing volume of recorded data effectively, a method for automatic classification of GIC in autotransformer neutral was proposed. The method is based on a continuous wavelet transform of the neutral current data combined with a convolutional neural network (CNN) to classify the obtained scalogram images. As the result of comparing four CNNs with different architectures, a model that showed excellent GIC classification performance on the validation set (100.00% accuracy and loss of 0.0115) was chosen.

Inflammatory bowel disease (IBD), including ulcerative colitis and Crohn's disease, is a complex gastrointestinal disorder with a multifactorial etiology, including environmental triggers, autoimmune mechanisms, and genetic predisposition. Despite advancements in therapeutic strategies for IBD, its associated mortality rate continues to rise, which is often attributed to unforeseen side effects of conventional treatments. In this context, we explored the potential of Ecklonia cava extract (ECE) derived from an edible marine alga known for its anti-inflammatory and antioxidant properties in mitigating IBD. This study investigated the effectiveness of ECE as a preventive agent in a murine model of dextran sulfate sodium (DSS)-induced colitis. Our findings revealed that pretreatment with ECE significantly ameliorated colitis severity as evidenced by increased colon length, reduced spleen weight, and histological improvements demonstrated by immunohistochemical analysis. Furthermore, ECE significantly attenuated the upregulation of inflammatory cytokines and mediators and the infiltration of immune cells known to be prominent features of colitis in mice. Notably, ECE restored dysbiosis of intestinal microflora and aided in the recovery of damaged intestinal mucosa. Mechanistically, ECE exhibited protective effects against pathogenic colitis by inhibiting the NLRP3/NF-κB pathway known to be pivotal regulators in the inflammatory signaling cascade. These compelling results suggest that ECE holds promise as a potential candidate for IBD prevention. It might be developed into a functional food for promoting gastrointestinal health. This research sheds light on the preventive potential of natural compounds like ECE in the management of IBD, offering a safer and more effective approach to combating this challenging disease.

Vibrations of plate structures placed in a supersonic flow is considered. The undisturbed fluid flow is parallel to the plate. Two specific problems are treated: in the first one the plate is in the form of an infinite strip and the flow is in the direction of its finite length. Rigid walls extend from the sides of the plate indefinitely. In the second problem, the plate is a finite rectangle and the flow is parallel to one of its sides. The first problem is a limiting case of the second problem. The flow is modeled by piston theory which assumes that the fluid pressure on the plate is proportional to local slope. This approximation is widely used at high speeds, and reduces the interaction between the fluid flow and the vibrations of the plate to an additional term in the vibration equation. The resulting problem can be solved by assumed mode methods. In this study, the solution is also carried out by using the collocation method. The main result is the flutter velocity of the free fluid flow under which the plate vibrations become unstable. Finally, simple expressions are proposed between the various non-dimensional parameters that allows quick estimation of flutter velocity.

The present paper describes a study case of the failure investigation of Duplex stainless steel (UNS S31803) on the tube and tube sheet section of a shell and tube heat exchanger BEM TEMA type with seawater as the cooling medium. Although UNS S31803 offers high strength, high resistance to chloride-induced SCC, and high resistance to pitting attack in chloride environments, in this study case, the heat exchanger experienced some material degradation; 26 tubes were leaked and plugged on both sides, and scales plugged 76 tubes. The examination in this study case revealed the formation of biofilm inside the tubes, XRD examination revealed that the film contained aragonite (CaCO3), and by using microstructural examination on the inner surface of the tube, the austenite grains were preferentially attacked by crevice corrosion. In this case, the failure was caused by crevice corrosion, and crevice corrosion was enhanced by microbiological-induced corrosion (MIC). Recommendations to avoid similar failures are also suggested in this paper.

In recent years, laser engraving has received widespread attention as a convenient, efficient, and programmable method, which has enabled the obtaining of high-quality porous graphene from various precursors. Laser engraving is often used to fabricate the dielectric layer with micro-structure for capacitive pressure sensors, however, the usual choice of electrodes remains poorly flexible metal electrodes, which greatly limits the overall flexibility of the sensors. In this work, we propose a flexible capacitive pressure sensor made entirely of thermoplastic polyurethane (TPU) and laser-induced graphene (LIG) derived from wood. The capacitive pressure sensor consisted of a flexible LIG/TPU electrode (LTE), a LIG/TPU electrode with micro hole array, and dielectric layer of TPU with micro-cone array molded from laser-engraved hole array on wood, which provided high sensitivity (0.11 kPa-1), ultra-wide pressure detection range (100Pa to 1.4MPa), fast response (~300 ms) and good stability (&gt;4000 cycles, at 0-35 kPa). We believe that our research makes a significant contribution to the literature because the easily available materials derived from wood and overall consistent flexibility meet the requirements of flexible electronic devices.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

The fall armyworm (FAW), Spodoptera frugiperda, has become one of the most important pests on corn in China since it invaded in 2019. Although FAW has not been reported to cause widespread damage to rice plants in China, it has been sporadically found feeding in the field. If FAW infests rice in China, the fitness of other insect pests on rice may be influenced. However, how FAW and other insect pests on rice interact remains unknown. In this study, we found that the infestation of FAW larvae on rice plants prolonged the developmental duration of the brown planthopper (BPH, Nilaparvata lugens (Stål)) eggs, and plants damaged by gravid BPH females did not induce defenses that influenced the growth of FAW larvae. Moreover, co-infestation by FAW larvae on rice plants did not influence the attractiveness of volatiles emitted from BPH-infested plants to Anagrus nilaparvatae, an egg parasitoid of rice planthoppers. FAW larvae were able to prey on BPH eggs laid on rice plants and grew faster compared to those larvae that lacked available eggs. Studies revealed that the delay in development of BPH eggs on FAW-infested plants was probably related to the increase in levels of jasmonoyl-isoleucine, abscisic acid and the defensive compounds in the rice leaf sheaths on which BPH eggs were laid. These findings indicate that if FAW invades rice plants in China, the population density of BPH may be decreased by intraguild predation and induced plant defenses, whereas the population density of FAW may be increased.

The current study aimed to investigate the antitumor effects and potent mechanism of cytokine-induced killer (CIK) cells combined with irreversible electroporation (IRE) via an in vitro function assay in an in vivo Panc02 cell–bearing mouse model. We established an in vitro culture assay for CIK cells and determined the proportions of different peripheral lymphocytes. The antitumor effect of the combination of IRE and CIK cells in a Panc02 pancreatic-cancer (PC) subcutaneous-xenograft model was investigated; tumor size and mouse survival rates were recorded. We used flow cytometry (FCM) to analyze the proportion of intratumoral lymphocytes, the expression of chemokine receptors, and the proliferative activity of CIK cells. The proportion of cells that were positive for clusters of differentiation 3 and 8 (CD3+CD8+) and the proportion of CD3+CD56+ cells were both significantly increased after 21 days of in vitro culture. Combined IRE/CIK cell treatment significantly inhibited tumor growth and increased the survival rate of Panc02 cell–bearing mice. Furthermore, infiltration of lymphocytes into tumor tissue was significantly increased by this combination therapy compared with the untreated group or monotherapy group. In addition, IRE significantly enhanced the expression of chemokine receptors elicited by, and the proliferative activity of, CIK cells. In conclusion, IRE combined with CIK cells showed superior antitumor efficacy in a PC subcutaneous-xenograft model, which we attributed to the promotion of lymphocytic infiltration, as well as to upregulation of chemokine receptor expression and of regulators of CIK cell proliferation.

Background: Despite the existence of a wide variety of anti-inflammatory drugs, the vast majority are classified as steroidal or non-steroidal. Both classes with many side effects that limit usage. Thus, the search for new molecules with anti-inflammatory potential is still important. Methods: Five phenylbenzohydrazides were synthetized and evaluated in pre-clinical models of acute inflammation in vivo and in vitro. Results: Substances significantly reduced cell migration induced by carrageenan. It was also observed an intense inhibition in protein extravasation and cytokines (IL-6, IL-1β, and TNF-α) production as well as nitric oxide reduction. INL-11 demonstrated to be the most potent since the reduction was significant even when compared with dexamethasone. In vitro INLs also reduced cytokines and NO production and iNOS activity. INL-11 was the most effective in reducing cell migration in vitro. Conclusions: our data suggest that these substances are suitable for further development to new series of compounds that could lead to new hits and future drug prototypes for anti-inflammatory conditions.

Although lithium-ion batteries have extensively been used in various applications because of their high energy capacity, fracture and failure, the by-products of large strains and stresses caused by fast charging and discharging need yet to be addressed. The size effects on the mechanical behavior of the nano-sized structures are significant; however, the classical elasticity theory may not consider such effects. On the other hand, surface stress theory, as a robust and potential theory, is suitable in considering size effects in nano-scale structures. Therefore, in this paper, in order to involve the surface stress effects on the fracture behavior of Li-ion batteries, the following steps are taken. Firstly, a phase-field model is used to determine the evolution of the concentration profile. Subsequently, the stress distribution is obtained by using the surface stress theory combined with chemical equations for a planar electrode. Afterward, by using the weight function method for an edge crack in the plate, the stress intensity factor is derived for all time steps and possible crack lengths during the process. It is found that with increasing phase boundary thickness parameter or decreasing phase-separation phenomenon, the surface mechanics parameters become more influential. Furthermore, in the presence of positive surface stress, the diffusion-induced stress distribution decreases, which in turn reduces the stress intensity factor. In addition, in this paper, the two states of surface stress are compared either for elastic or total strain. Concerning stresses and concentrations, the results indicate a big difference at the beginning of the deintercalation process showing, in particular, 2% for stresses, but the differences diminish gradually.

Arboviruses of medical and veterinary significance have been identified on all 7 continents with every human and animal population at risk for exposure. Like arboviruses, chronic neurodegenerative diseases like Alzheimer’s and Parkinson’s disease are found wherever there are humans. Viral parkinsonism has been documented for a variety of human pathogens though there are few studies that evaluate the effects of viral infection on degenerative neurological diseases. Significant differences in baseline gene and protein expression have been determined between Human Induced Pluripotent Stem Cell lines derived from a non-Parkinson’s disease individual and from an individual with reported Parkinson’s disease. While the organoids generated from each cell line were physically indistinguishable, significant differences were observed in gene and protein expression for neurotransmission and immunity. It was hypothesized that these inherent differences would impact cerebral organoid responses to viral infection. In this preliminary observational study, cerebral organoids from a non-Parkinson’s and Parkinson’s patient were infected with Chikungunya virus and observed for 2 weeks. Parkinson’s organoids lost mass and exhibited a dysfunctional antiviral response. Neurotransmission data from both non-Parkinson’s and Parkinson’s organoids had dysregulation of IL-1, IL-10, IL-6. These cytokines are associated with mood and could be contributing to persistent depression seen in patients following CHIKV infection. Both organoid types had increased expression of CCR5 and CXCL10 which are linked to demyelination, highlighting a potential mechanism for virus-associated parkinsonism. The dysfunctional antiviral response of Parkinson’s organoids highlights the need for more research in neurotropic infections in a neurologically compromised host.

The development of 3D cerebral brain organoids which accurately resemble aspects of the human brain permits a more accurate characterization of physiological processes and neurological diseases. Cerebral organoids can be grown from stem cell lines with various genetic backgrounds allowing multiple neurodegenerative diseases to be modeled. While dysfunction in neurotransmission of patients with neurodegenerative diseases is expected, the impact of chronic neurodegeneration on the response to viral infection of the CNS is poorly understood. For instance, several mosquito-borne viruses like Dengue virus and West Nile Virus cause post-viral parkinsonism. How CNS infection might impact a host with inherent CNS dysfunction such as Parkinson’s Disease in poorly understood. This preliminary, observational study aimed to understand dysfunction in intrinsic and innate expression of a patient with a neurodegenerative disease and a non-affected individual in relation to potential viral infection in the CNS. Cerebral organoids were generated from human induced pluripotent stem cells with a normal genetic background or with idiopathic Parkinson’s Disease. After differentiation and maturation, organoid size, gene expression and immunofluorescence were evaluated to assess neurotransmission and innate immunity. While there was no significant difference in size of the organoids with a normal or Parkinson’s genetic background, gene expression studies identified multiple differences in innate immunity and neurotransmission. Immunofluorescence also identified differences in protein expression related to neurotransmission and innate immunity. Of note, organoids derived from a Parkinson’s patient exhibited endogenous up-regulation of dopamine and muscarinic acetylcholine receptors, GABA, glycine, and glutamate targets, and the majority of cytokines. This expression pattern suggests a chronic state of neuroexcitation and neuroinflammation in this population of organoids.

Introduction: Valproic acid (VPA) is an antiepileptic drug extensively used for treating partial and generalised seizures, acute mania and as prophylaxis for bipolar disorder. Drug-induced liver injury (DILI) persists as a significant issue related to fatal outcomes by VPA. The aim of this study was to increase our knowledge about this condition and to better identify patients affected. Methods: We conducted an observational retrospective case-control study that identified cases of DILI by VPA from the Pharmacovigilance Programme from our Laboratory Signals at La Paz University Hospital from January 2007 to December 2019. From the Therapeutic VPA Monitoring Programme, two control groups were assigned, VPA-tolerant patients and the other with patients who developed mild VPA-related hepatitis but who did not meet the DILI criteria, matched for date, age and sex. Results: A total of 60 patients were included in the study: 15 cases of DILI, 30 VPA-tolerant controls and 15 controls with mild hepatitis. Mean age for the cases was 45.7 years, 4(26.7%) were women and 5(33.34%) were children under 18 years, of them 3(20%) were fatal. Polytherapy with other antiepileptic drugs (p=0.047) and alcohol consumption (p<0.001) were associated with a greater risk of developing DILI by VPA. A diagnosis of epileptic seizure was more frequently related to DILI when compared with the VPA-tolerant controls (p<0.001). The cases developed hepatocellular hepatitis (p<0.001), while the mild hepatitis controls had a higher rate of cholestatic hepatitis (p<0.001). The laboratory lactate dehydrogenase values were statistically higher (even at baseline) in patients with DILI than in both control groups (p= 0.033 and p=0.039). Conclusions: VPA hepatotoxicity remains a considerable problem. This study offers interesting findings for characterising VPA-induced liver injury and at-risk patients.

It is important to distinguish between natural earthquakes and those induced by CO2 injection at carbon capture and storage sites. For example, the 2004 Mw 6.8 Chuetsu earthquake occurred close to the Nagaoka CO2 storage site during gas injection, but we could not quantify whether the earthquake was due to CO2 injection or not. Here we simulated changes of pore pressure during CO2 injection at the Nagaoka site and compared them with estimated natural seasonal fluctuations of pore pressure due to rainfall and snowmelt as well as estimated pore pressure increases related to remote earthquakes. We clearly distinguished changes of pore pressure due to CO2 injection from those due to rainfall and snowmelt. The simulated local increase in pore pressure at seismogenic fault area was much less than the seasonal fluctuations related to precipitation and increases caused by remote earthquakes, and the lateral extent of pore pressure increase was insufficient to influence seismogenic faults. We also demonstrated that pore pressure changes due to distant earthquakes are capable of triggering slip on seismogenic faults. The approach we developed could be used to distinguish natural from injection-induced earthquakes and will be useful for that purpose at other CO2 sequestration sites.

We report on space-selective crystallization of congruent and polar Sr2TiSi2O8 crystals in a stoichiometric SrO-TiO2-SiO2 glass induced by (1030 nm, 300 fs) femtosecond laser irradiation. This allows us to compare with non-congruent laser induced crystallization of polar LiNbO3, in non stoichiometric Li2O-Nb2O5-SiO2 glass and gain information on the mechanism of nanocrystals orientation with the laser polarization that we pointed out previously. Using scanning electron microscopy (SEM), Second-harmonic generation (SHG) and electron backscattered diffraction (EBSD), we studied the laser induced crystallization according to the laser processing parameters (pulse energy, pulse repetition rate, scanning speed). We found 1) a domain where the laser track is filled with crystals not perfectly textured (low energy), 2) a domain where an amorphous volume remain surrounded by a crystallized shell (high energy). This arises from Sr out-diffusion and may gives rise to crystallization of both SrTiO3 and Sr2TiSi2O8 phases at low speed. In the one-phase domain (at higher speed), it is found the possibility to elaborate a tube with a perfect fresnoite texture. Significant difference in size and morphology whereas crystallization threshold remains similar are discussed based on glases thermal propeties. Contrarily to Li2O-Nb2O5-SiO2 (LNS) glass, no domain of oriented nanocrystallization controlled by the laser polarization has been found in SrO-TiO2-SiO2 (STS) glass, which is attributed to the larger crystallization speed in STS glass. No nanogratings have also been found that is likely due to the congruency of the glass.

Inertial focusing conditions of fluorescent polystyrene spherical particles are studied at the pointwise level along their pathlines. This is accomplished by an algorithm that calculates a de-gree of spreading function of the particles' trajectories taking streaklines images as raw data. Different confinement ratios of the particles and flow rates are studied and the results are pre-sented in state diagrams showing the focusing degree of the particles in terms of their position within a curve of an asymmetric serpentine and the applied flow rate. In addition, together with numerical simulation results, we present empirical evidence that the preferred trajectories of inertially focused spheres are contained within Dean vortices' centerlines. We speculate about the existence of a new force, never postulated before, to explain this fact.

Polyvinyl alcohol-engineering cementitious composites (PVA-ECC) has been widely applied in bridge deck repairing or widening, the common practice for doing this is that a portion of a bridge is left open to traffic while the closed portion is constructed, which expose the early age PVA-ECC to the vehicle-induced vibrations. However, whether vehicle-induced vibrations affect the tensile performance of early age PVA-ECC remains unknow. The purpose of this study was to conduct laboratory test programs on how much vehicle-induced vibrations during early ages affected the tensile performance of PVA-ECC. A self-improved device was used to simulate the vehicle-induced vibrations, and after vibrating with the designed variables, both a uniaxial tensile test and a grey correlation analysis were performed. The results indicated that: the effects of vehicle-induced vibrations on the tensile performance of early age PVA-ECC were significant, and they generally tended to be negative in this investigation. In particular, for all of the vibrated PVA-ECC specimens, the most negative age when vibrated occurred during the period between the initial set and the final set. We concluded that although vehicle-induced vibrations during the setting periods had no substantial effects on the inherent strain-hardening characteristics of PVA-ECC, the effects should not be ignored.

Q-switched laser radiation at wavelengths of 355 nm, 532 nm, and 1064 nm from a Nd: YAG laser was used to generate plasma in laboratory air at the target surface made of compressed nano-silver particles of size 95 ± 10 nm. The emitted resonance spectra from the neutral silver at wavelengths of 327.9 nm and 338.2 nm indicate existence of self-reversal in addition to plasma self-absorption. Both lines were identified in emission spectra at different laser irradiation wavelengths with characteristic dips at the un-shifted central wavelengths. These dips are usually associated with self-reversal. Under similar conditions, plasmas at the corresponding bulk silver target were generated. The recorded emission spectra were compared to those obtained from the nano-material target. The comparisons confirm existence of self-reversal of resonance lines that emerge from plasmas produced at nano-material targets. This work suggests a method for recovery of the spectral line shapes and discusses practical examples. In addition, subsidiary calibration efforts that utilize the Balmer series Hα-line reveal that other Ag I lines at 827.35 nm and 768.7 nm are optically thin under variety of experimental conditions and are well-suited as reference lines for measurement of the laser plasma electron density.

In this research, the computational fluid dynamic (CFD) approach that has been used in wind power generation field was applied for the solution of the problems of local strong wind areas in railway fields, and the mechanism of wind generation was discussed. At the same time, the affectivity of the application of computational fluid dynamic approach to railway field was discussed. The problem of local wind that occurs on the railway line in winter was taken up in this research. A computational simulation for the prediction of wind conditions by LES was implemented and it was clarified that the local strong wind area is mainly caused by separated flows originating from the small‐scale terrain positioned at its upstream (at approximately 180.0 m above sea level). Meanwhile, the effects of the size of calculation area and spatial grid resolution on the result of calculation and the effect of atmospheric stability were also discussed. It was clarified that when the air flow characteristic of the separated flow originating from the small‐scale terrain (at altitude of approximately 180.0 m) targeted in this research is reproduced at high accuracy by computational simulation of wind conditions, approximately 10.0 m of spatial resolution of computational grid in horizontal direction is required. As a result of the computational simulation of wind conditions of stably stratified flow (Fr = 1.0), lee waves were excited at the downstream of the terrain over time. As a result, the reverse‐flow region lying behind the terrain that had been observed at a neutral time was inhibited. Consequently, local strong wind area was generated at the downstream of the terrain and the strong wind area passing through the observation mast was observed. By investigating the speed increasing rate of local strong wind area induced at the time of stable stratification, it was found that the wind was approximately 1.2 times stronger than what was generated at a neutral time.

Electrically conductive polymer composites are in high demand for modern technologies, however, the intrinsic brittleness of conducting conjugated polymers and the moderate electrical conductivity of engineering polymer/carbon composites have highly constrained their applications. In this work, super high electrical conductive polymer composites were produced by a novel hot embossing design. The polydimethylsiloxane (PDMS) composites containing short carbon fiber (SCF) exhibited an electrical percolation threshold at 0.45 wt%, and reached a saturated electrical conductivity of 49 S/m at 8 wt% of SCF. When reduced the sample thickness from 1.0 mm to 0.1 mm by the hot embossing process, a compression-induced percolation threshold occurred at 0.3 wt%, while the electrical conductivity was further enhanced to 378 S/m at 8 wt% SCF. Furthermore, the additional of a second nanofiller of 1 wt%, such as carbon nanotube or conducting carbon black further increased the electrical conductivity of the PDMS/SCF (8 wt%) composites to 909 S/m and 657 S/m, respectively. The synergy of the densified conducting filler network by the mechanical compression and the hierarchical micro-/nanoscale filler approach has realize super high electrical conductive yet mechanical flexible polymer composites for modern flexible electronics applications.

This work communicates results from optical emission spectroscopy following laser-induced optical breakdown at or near nanomaterial. Selected atomic lines of silver are evaluated for consistent determination of electron density. Comparisons are presented with Balmer series hydrogen results. Of particular interest are measurements free of self-absorption effects. For several silver lines, asymmetries are observed in the recorded line profiles. Electron densities of interest range from 0.5 to 3 × 10¹⁷ cm^-3, for 5 nanosecond Q-switched Nd:YAG radiation at wavelengths of 1064, 532, and 355 nm, and for selected silver emission lines including 328.0, 338.2, 768.7, and 827.3 nm, and the hydrogen alpha Balmer series line at 656.3 nm. Line asymmetries are presented for the 328.0 nm Ag I line that is measured following generation of the plasma due to multiple photon absorption. This work explores electron density variations for different irradiance levels, and reports spectral line asymmetry of resonance lines for different laser fluence levels.

Direct reprogramming of fibroblasts into induced cardiomyocytes (iCMs) holds a great promise for regenerative medicine and has been studied in several major directions. However, cell-cycle regulation, a fundamental biological process, has not been investigated during iCM-reprogramming. Here, our time-lapse imaging on iCMs, reprogrammed by Gata4, Mef2c, and Tbx5 (GMT) monocistronic retroviruses, revealed that iCM-reprogramming was majorly initiated at late-G1- or S-phase and nearly half of GMT-reprogrammed iCMs divided soon after reprogramming. iCMs exited cell cycle along the process of reprogramming with decreased percentage of EdU⁺/αMHC-GFP⁺ cells. S-phase synchronization post-GMT-infection could enhance cell-cycle exit of reprogrammed iCMs and yield more GFP^high iCMs, which achieved an advanced reprogramming with more expression of cardiac genes than GFP^low cells; however, S-phase synchronization didn’t enhance the polycistronic-MGT reprogramming, in which cell-cycle exit had been accelerated. In conclusion, post-infection synchronization of S-phase facilitated the early progression of GMT-reprogramming through a mechanism of enhanced cell-cycle exit.

The SBA-15 loaded with methylene blue was successfully prepared by sample adsorption of methylene blue in SBA-15 and is characterized by an XRD, SEM, FTIR, and BET. The photocatalytic activity for methyl orange (MO) degradation was investigated under visible light irradiation under LEDs. Experimental results demonstrate that the SBA-15-MB exhibited higher photocatalytic activity than SBA-15 under visible light irradiation. The degradation efficiency of MO (50 ppm) by SBA-15-MB could reach 80% within 180 min under 25W LED visible light. The photocatalytic activity of SBA-15 could be attributed to the excitation of methylene blue by visible light, the transfer of electrons from methylene blue to SBA-15, and the production of radicals at the surface of SBA-15.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

In recent years, researches on combining wavelet decomposition and convolutional neural network (CNN) together to classify hyperspectral images (HSI) have emerged, and some effective classification models have been proposed and achieved good classification results. However, there are two problems for most of the proposed models. One is the heavy training parameters and the other is that there is no distinction between the classification effectiveness of low frequency and high frequency features after wavelet decomposition. In this paper, a new light-weighted HSI classification model (LLFWCNN) is proposed, which performs multi-layer wavelet decomposition for HSI after dimensionality reduction, and only arranges the low frequency features in a specific stack mode, then classifies them through a well-designed convolutional neural network. Compared with other classification models, the number of parameters is only 2.5% of that of other models. And only the low frequency features after wavelet decomposition are used, while the high frequency features are abandoned. The results showed that compared with the state-of-the-art classification models, LLFWCNN could obtain the same or even better classification results with fewer network parameters and proved that the low frequency features after wavelet decomposition provide LLFWCNN with more favorable information for HSI classification as well.

Monolayer graphene absorbs 2.3 percent of the incident visible light. This “small” absorption has been used to emphasize the visual transparency of graphene, but it in fact means that multilayer graphene absorbs a sizable fraction of incident light, which causes non-negligible fluorescence. In this paper, we formulate the light emission properties of multilayer graphene composed of tens to hundreds of layers using a transfer matrix method and confirm the method’s validity experimentally. We could quantitatively explain the measured contrasts of multilayer graphene on SiO2/Si substrates and found sizable corrections, which cannot be classified as incoherent light emissions, to the reflectance of visible light. The new component originates from coherent emission caused by absorption at each graphene layer. Multilayer graphene thus functions as a partial coherent light source of various wavelengths, and it may have surface-emitting laser applications.

The agricultural sector faces challenges due to climate change and the growing global population. Alkaline stress could adversely impact plant growth and crop production. This stressor diminishes water quality essential for crop cultivation, consequently impairing plant growth and overall productivity. Gamma-aminobutyric acid (GABA), a non-protein amino acid, may exhibit multifaceted roles in plant responses to adverse environmental conditions. Optimization of crop production in controlled environmental agriculture under artificial light attracted much attention. In the present study, we investigated the effects of different light spectra and GABA concentrations on Lollo Rosso lettuce plants under alkaline stress. Seedlings were placed under different light spectra [red (R), blue (B), white (W), 3R:1B, and 2R:1B:1far-red (FR)] and treated by GABA (0 and 50 µmol). Alkaline conditions were instituted by applying NaHCO3 at a concentration of 40 mM. The experiment incorporated a control treatment without NaHCO3. In general, R light exposure caused the highest growth performance of lettuce plants. GABA augmented biomass production in control and alkaline-treated plants across all light spectra. Additionally, it increased the concentrations of photosynthetic and protective pigments under alkaline conditions. GABA also improved the photosynthetic performance under all light spectra. Non-photochemical quenching and pigmentation were enhanced by exposure to B light, especially in plants treated with GABA. Alkaline stress induced an increase in soluble carbohydrate content in the lettuce leaves. These findings highlight the support of GABA application in facilitating coping plants to alkaline stress.

The rapid and accurate detection of parasites is crucial for timely curative intervention in parasitosis and for epidemiological surveillance. To meet the needs of clinical diagnosis, it is imperative to develop a diagnostic tool based on nucleic acid that combines the sensitivity and specificity of established nucleic acid amplifica-tion tests with the speed, cost-effectiveness, and convenience of isothermal amplification methods. A new nu-cleic acid detection method, utilizing the clustered regularly interspaced short palindromic repeats (CRISPR)-associated (Cas) nuclease, holds promise for point-of-care testing. Specifically, the CRISPR-Cas12a system has demonstrated numerous advantages for detecting parasites, with hopeful outcomes for identify-ing malaria, toxoplasmosis, and other parasitic ailments. This review provides an overview of how CRISPR-Cas12a can be utilized for parasite detection, evaluates its advantages and disadvantages, and sug-gests ways to improve the efficiency and sensitivity of CRISPR-Cas12a-based assays.

Breast cancer is a global health concern, necessitating continuous advancements in diagnostic medical imaging technologies for early detection and improvement of treatment. This paper presents an overview of the past, present and future of breast cancer imaging using light and some results from the current studies. The paper specifically presents the role of Diffuse Optical Tomography (DOT) in breast cancer imaging. Conventional methods, such as X-ray mammography, face limitations. Diffuse Optical Tomography, a non-invasive light-based imaging modality can provide quantitative descriptive and architectural information about breast tissue. The paper discusses the key challenges and recent developments in breast cancer imaging using DOT to overcome some key challenges. This paper aims to contribute to the understanding of the evolving technological landscape in breast cancer imaging using light for improving early detection and patient outcomes.

The LED light source is an important light source for indoor visible light communication. It has the characteristics of a large divergence angle and a high transmission rate. Therefore, using LED as the light source for visible light full-duplex communication can not only satisfy the lighting requirements but also transmit information at high speed. To analyze the factors that affect the optical power of the indoor single-light source visible light communication uplink receiving end, an indoor visible light communication model was established, and mathematical calculation formulas were derived based on the model establishment, and the maximum movable range formula of the retroreflective end under specific conditions was derived; The reliability of the formula was verified with the help of Zemax simulation software. Theoretical analysis and experimental results show that increasing the movement range of the retroreflective end can be achieved by increasing the lens diameter, reducing the focal length, and increasing the link distance.

Legumes are a diverse and important group of plants that play a vital role in agriculture, food security, and environmental sustainability. Rhizobia are symbiotic bacteria that form nitrogen-fixing nodules on legume roots, providing the plant with a valuable source of nitrogen. Phenolic acids are a group of secondary metabolites produced by plants that have a wide range of biological functions, including defense against pests and diseases, tolerance to abiotic stresses, and nutrient uptake. In the context of climate change and the imperative for sustainable agriculture, this study delves into the dynamic responses of legume species to varying light intensities and their intricate interactions with soil microorganisms. We investigated the impact of light intensity and rhizobial inoculation on the biomass, nitrate reductase, acid phosphatase, and production of phenolic acids in the roots of four legume species, Trifolium repens, Vicia sativa, Ornithopus compressus, and Coronilla juncea. Plants were grown under three light intensity regimes (low, medium, and high) and inoculated with either rhizobia or a non-inoculated control. The results highlights that shaded-light-adapted species, T. repens and V. sativa, increased root exudate production when exposed to high light intensity. This response aligns with their mining strategy, effectively allocating resources to optimize nutrient acquisition under varying conditions. In contrast, species hailing from well- illuminated environments, O. compressus and C. juncea, displayed distinct strategies by significantly increasing biomass under high irradiance, capitalizing on the available light and nutrients. The mining strategy of legumes emerged as a central theme, influencing biomass production, nitrogen dynamics, and enzymatic activities. The strong correlations between biomass and total nitrogen accumulation underscore the role of the mining strategy in efficient nutrient acquisition. Inoculated plants, which rely more on biological nitrogen fixation (BNF), exhibited lower δ15N values, indicative of a successful mining strategy to acquire and utilize atmospheric nitrogen. Enzymatic activities and phenolic acids exhibited significant interspecies variations, reflecting the adaptability of legumes to different light conditions. The findings of this study could be used to develop new strategies for improving legume stress tolerance, nutrient uptake capacity, and rhizosphere health.

Super-resolution technology is important not only in bio-related fields but also in nanotechnology, particularly in the semiconductor industry, where fine patterning is required and super-resolution is essential. However, observing microstructures beyond the diffraction limit proposed by Abbe and Rayleigh is considered impossible because of diffraction in traditional optical microscopy ob-servation techniques. However, in recent years, it has been possible to observe microstructures beyond the Rayleigh criterion by analysing the phase distribution of light. This study investigated the physical reasons why phase analysis makes this new analysis technique possible using simula-tions. The results confirmed that the phase component of the zero-order diffracted light reflected from the microstructure and able to pass through the lens system contained the phase information related to the shape of the measured object. Analysis of this information demonstrates the possi-bility of realising super-resolution based on speckle interferometry.

3D printing technology has brought about a paradigm shift in the delivery of clinical care in medicine and dentistry. There are several different 3D printing technologies, which, along with different printable materials with unique biomechanical properties, allows for a wide range of applications for 3D printing in dentistry. The clinical use of 3D printing has created versatile applications which streamline our digital workflow. Technological advancements have also paved the way for the integration of new dental materials in dentistry. This paper provides an overview of the mechanisms of 3D printing, the dental materials relevant to each mechanism and the possible applications of these materials within different areas of dentistry. Understanding the existing spectrum of 3D printing applications in dentistry will serve to further expand its use in the dental field.

Four strains of green microalgae (Scenedesmus acutus, Scenedesmus vacuolatus, Chlorella sorokiniana and Chlamydomonas reinhardtii) were compared for growth and pigment composition under photoautotrophic or heterotrophic conditions. Batch growth experiments were performed in multicultivators with online monitoring of optical density. For photoautotrophic growth, light-limited (CO2-sufficient) growth was analysed under different light intensities during exponential and deceleration growth phases. The specific growth rate, mesured during exponential phase, and the maximal biomass productivity, measured during deceleration phase, were not related to each other when different light intensities and different species were considered. This indicates species-dependent photoacclimation effects during cultivation time, which was confirmed by light-dependent changes in pigment contents and compositions when exponential and deceleration phases were compared. Except for C. reinhardtii, that does not grow on glucose, heterotrophic growth was promoted to similar extents by acetate or by glucose, however these two substrates led to different pigment compositions. Weak light increased pigment contents during heterotrophy in the four species, but was efficient in promoting growth only in S. acutus. C. sorokiniana and S. vacuolatus exhibited the best potential for heterotrophic biomass productivities both on glucose and acetate, with carotenoid (lutein) content being the highest in the former.

: This work introduces the instrument design of the medium energy proton detector (MEPD, detection range: 30keV-5MeV) mounted on the Chinese Fengyun-4B (FY-4B) satellite. Compared with the similar detector on the Fengyun-3E (FY-3E) satellite, the instrument has undergone significant changes due to the different orbital radiation environment and solar lighting conditions. Based on the calculation of radiation model AP8, the geometry factor is reduced to 0.002 cm2sr, while the MEPD on FY-3E satellite is 0.005 cm2sr. Another difference is that sensors in some directions is exposed to direct sunlight for 80 minutes every day on this orbit, depending on the attitude angle of the satellite, which is much worse than that on FY-3E satellite. According to the calculation results of permeability of photons through different materials, a 100 nm thickness nickel film is added in front of sensors in order to eliminate light pollution completely. The experiment on the solar simulator shows that the measure is effective and the detector has no error counts when the solar irradiance coefficient is 1.0. In addition, Geant4 software is applied to simulate particle transportation process under complete machine condition so that to check the contamination of electrons on sensors among all directions after magnetic deflection. Data obtained in orbit shows that the instrument works properly, and the data is in good agreement with the AP8 model. The observations of the MEPD on board the FY-4B satellite can provide important support for the safety of the spacecraft and the theoretical research related to space weather.

Nanoparticles are of great importance for various scientific and technological applications, drug discovery, ecology, molecular biology, etc. Size is a basic characteristic of any particle, and dynamic light scattering is beyond competition when measuring particle size in dispersions ranging from nanometers to micrometers. Unfortunately, this method has a serious problem in processing and interpreting experimental data. Instrument noise and polydispersity of the sample lead to the situation when one initial autocorrelation function corresponds to several different particle size distributions. Sometimes these different solutions of the inverse task can be found by changing parameters in the software. Sometimes the scientist cannot be suspicious of possible other solutions, having one result from the program. In this article I demonstrate the problem on model and experimental data using three known programs: CONTIN, the Malvern Zetasizer and DynaLS. I also present my own free program Autocor, which allows to test our own hypotheses about the modality and shape of the particle size distribution by optimizing the parameters of our own models with a small number of degrees of freedom.

Simultaneous biofortification of vegetable crops with selenium and iodine is necessary in areas where there is a lack of these two elements. The main reason for lack of selenium and iodine in humans is inadequate intake of these two elements from vegetable crops. Biofortification through various agricultural methods including artificial lighting is a pragmatic way of increasing the concentration of these elements in plants. This research was conducted as a three-factor factorial experiment arranged as completely randomized pots replicated thrice in the greenhouse during year 2022. Three levels of sodium selenate fertilizer (S1: 0, S2: 2, S3: 4 mg/l), three levels of potassium iodate (I1: 0, I2: 2, I3: 4 mg/L) and two additional blue light radiation levels (L1: radiation and L2: no blue light radiation) were applied and data was measured at two growth stages namely 40 and 80-days. The results showed that the highest (11.44 g) and the lowest (9.55 g) shoot dry weight values at the 40-day-stage were observed in the supplementary blue light and sunlight (control), respectively. Moreover,, under complementary blue light conditions, the highest and the lowest (5.85 and 3.38 mg/g leaf fresh weight) of leaf chlorophyll value at the 40-day-stage were recorded at sodium selenate 4 and 0 mg/l, respectively. The highest and the lowest (5.24 and 4.76 mg/g) fresh weight of leaf anthocyanin at the 40-day-growth stage were related to supplementary blue light and sunlight treatment (control), respectively. Under the supplementary blue light and 0 mg/l of selenium , the highest and the lowest value of shoot trigonelline (102.56 and 72.14 mg/100 g fresh weight) were obtained at 4 and 2 mg/L of iodine, respectively. Furthermore, in the same treatment, the highest and the lowest of seed trigonelline amounts (0.99 and 0.74 mg/g dry weight) corresponded with 4 and 0 mg/l of iodine, respectively.

Electroactive microorganisms have received a lot of interest in the field of environmental engineering and biotechnology because of their extracellular electron transfer (EET) capability of energy recovery and environmental remediation. However, the low efficiency of EET remains a barrier to its practical implementation. This review presents an introduction to EET, followed by addressing strategies for enhancing EET through different approaches including enhancing EET by mediator materials, external electricity, photo, and magnetism as well as integrated strategies, that is, the combination of multiple means to promote extracellular electron transport and improve the performance of microbial electrochemical systems. Finally, the challenges, perspectives, and new directions for EET enhancement will be discussed.

With the advent of deep learning, significant progress has been made in low-light image enhancement methods. However, deep learning requires enormous paired training data, which is challenging to capture in real-world scenarios.To address this limitation, this paper presents a novel unsupervised low-light image enhancement method, which first introduces the frequency domain features of images in low-light image enhancement tasks. Our work is inspired by imagining a digital image as a spatially varying metaphoric “field of light”, then subjecting the influence of physical processes such as diffraction and coherent detection back onto the original image space via a frequency-domain to spatial-domain transformation (inverse Fourier transform). However, the mathematical model created by this physical process still requires complex manual tuning of the parameters for different scene conditions to achieve the best adjustment. Therefore, we proposed a dual-branch convolution network to estimate pixel-wise and high-order spatial interactions for dynamic range adjustment of the frequency feature of the given low-light image. Guided by the frequency feature from the “field of light” and parameter estimation networks, our method enables dynamic enhancement of low-light images. Extensive experiments have shown that our method performs well compared to state-of-the-art unsupervised, and its performance approximates the level of the state-of-the-art supervised methods qualitatively and quantitatively. At the same time, the light network structure design allows the proposed method to have an extremely fast inference speed(nearly 150 FPS on an NVIDIA 3090 Ti GPU for an image of size 600×400×3 ). Furthermore, the potential benefits of our method to object detection in the dark are discussed.

This paper presents the light scattering matrices of atmospheric aggregated hexagonal ice particles appearing in cirrus clouds. In this work aggregates consist of the same particles with different spatial orientation and number of these particles. Two types of particle shape were studied: (1) hexagonal column; (2) hexagonal plate. For both shapes we study compact and non-compact cases of arrangement of particles in aggregates. As a result, four sets of aggregates were made: (1) compact columns; (2) non-compact columns; (3) compact plates; (4) non-compact plates. Each set consists of eight aggregates with different number of particles from 2 to 9. For practical reason the bullet-rosette and the aggregate of hexagonal columns with different sizes was also calculated. The light scattering matrices were calculated for the case of arbitrary spatial orientation within the geometrical optics approximation for sets of compact and non-compact aggregates and within the physical optics approximation for two additional aggregates. It was found that light scattering matrix elements for aggregates are depend on arrangement of particles they are consisted.

Background and Objectives: Light therapy (LT) is used as an adjunctive treatment for sleep problems. This study evaluates the impact of LT on sleep quality and sleep-related parameters in patients with sleep disorders. Materials and Methods: We performed a pilot randomized, open-label clinical trial. Fourteen patients aged 20–60 years with sleep disorders for more than three months were randomized into the control and LT groups (1:1 ratio). The LT group was instructed to use a device that provides bright LT (6000 K, 380 lux, wavelength 480 nm) for at least 25 minutes before 09:00 am for two weeks. A self-reported questionnaire was used to evaluate circadian preference, mood, and sleep-related parameters. We analyzed serum cortisol levels and clock genes expression. Results: The Epworth Sleepiness Scale (ESS), insomnia severity index, and Pittsburgh Sleep Quality index were significantly improved within the LT group only after the two-week period. When comparing the two groups, only the change in ESS significant was significant (mean difference; control: -0.14 vs LT: -1.43, p=0.021) after adjusting for baseline characteristics. There were no significant differences in serum cortisol or clock genes expression. Conclusions: LT can improve daytime sleepiness in patients with sleep disorders; however, further well-designed studies are warranted to confirm its efficacy.

Introduction: Successful R0 resection is crucial for the survival of patients with primary liver cancer (PLC) or liver metastases. Up to date, surgical resection lacks a sensitive, real-time intraoperative imaging modality to determine R0 resection. Real-time intraoperative visualization with near-infrared light fluorescence (NIRF) using indocyanine green (ICG) may have the potential to meet this demand. This study evaluates the value of ICG visualization in PLC and liver metastases surgery regarding R0 resection rates. Materials and Methods Patients with PLC or liver metastases were included in this prospective cohort study. ICG 10mg was administered intravenously 24 hours before surgery. Real-time intraoperative NIRF visualization was made with the SpectrumTM Fluorescence Imaging Camera System. First, all liver segments were inspected with the fluorescence imaging system and intraoperative ultrasound for identification of the known tumor as well as additional lesions, compared to preoperative MRI. PLC, liver metastases, and additional lesions were then resected according to oncological principles. Of all resected specimens the resection margins were analyzed with the fluorescence imaging system for ICG positive spots right after resection. Histology of additional detected lesions as well as ICG fluorescence compared to histological resection margins were assessed. Results Of the 66 included patients median age was 65.5 years (IQR 58.7 - 73.9), 27 (40.9%) were female and 18 (27.3%) were operated laparoscopically. Additional ICG positive lesions were detected in 23 (35.4%) patients of which nine (29%) were malignant. In patients with no fluorescent signal at the resection margin, R0 rate was 93.9%, R1 rate was 6.1%, and R2 rate was 0% compared to a ICG positive resection margin with a R0 rate of 64.3%, R1 rate of 21.4%, and R2 rate of 14.3% (p=0.005). One and two year overall survival were 95.2% and 88.4%, respectively. Conclusion The here presented study provides significant evidence that ICG NIRF guidance helps to identify R0 resection intraoperatively. This offers a true potential to verify radical resection and improve patients´ outcome. Furthermore, implementation of NIRF guided imaging in liver tumor surgery allows to detect a considerable amount of additional malignant lesions.

Ultra-short laser pulses (1030 nm/230 fs) were used to laser ablate surface of crystalline sapphire. Laser ablated patterns were annealed at high temperature 1500∘C. Surface reconstruction took place removing ablation debris field at the edges of ablated pits in oxygen flow. Partial reconstruction of ripples was also observed.

Bright morning light (BML) entrains the body clock, modulates circadian rhythm, and improves sleep-wake disturbances. However, its impact on the autonomic nervous system (ANS) at night remains unclear. Hence, we investigated the effects of BML exposure on activities of the parasympathetic nervous system (PSNS) and sympathetic nervous system (SNS) at night. This non-randomized controlled pilot study included participants ≥60 years, diagnosed with a type of dementia or cognitive disorder. We excluded participants with pacemakers. The treatment group received 2500 lx BML, whereas the control group received approximately 200 lx of general lighting. We measured the heart rate variability to quantify ANS activity. The treatment group displayed significantly increased high-frequency (HF) power (Roy's largest root=2.44; P<.01) and insignificantly decreased normalized low-frequency (LF%) power. The corresponding low-frequency/high-frequency ratio (LF/HF), insignificant decrease, and cognitive function were correlated with PSNS activity (Roy's largest root=3.92; P<.01), which is effective for moderate dementia. BML exposure reduced SNS activity and enhanced PSNS activity at night, which consequently affected cognitive function. Furthermore, the light washout intervention markedly increased SNS activity at night. BML therapy may be a useful clinical tool for alleviating the deterioration of cognitive function.

Ultra-short 230 fs laser pulses of 515 nm wavelength were tightly focused into 700 nm focal spots and utilised in opening ~ 0.4 − 1 μm holes in alumina Al2O3 etch masks with 20-50 nm thickness. Such dielectric masks simplify fabrication of photonic crystal (PhC) light trapping patterns for the above-Lambertian performance of high efficiency solar cells. Conditions of laser ablation of transparent etch masks and effects sub-surface Si modifications were revealed by plasma etch- ing, numerical modeling, and minority carrier lifetime measurements. Mask-less patterning of Si is proposed using fs-laser direct writing for dry plasma etch of Si.

This paper describes the use of an open source instrument called LANcube v2 to build a lighting device inventory. The LANcube v2 is and instrument having 5 color sensitive sensors, each on a face of a cube. The instrument can be mounted on a car roof in order to create a map of the artificial light at night while roaming the streets and roads. Based on the temporal variations of the detected signal on various cube’s faces, we developed a method of finding the position in 3D of each lighting device. The lamp spectral types can be determined thanks to the color balance of the raw Red (R) Green (G) Blue (B) and Clear (C) color bands. If one assumes a typical angular photometry of a lighting device with respect to its location, it is possible to estimate its luminous flux. Such information allows us to build a lighting devices inventory of a territory. One advantage of that new method is that it can provide information about the private lighting devices that are always excluded from public lighting inventories. We will compare the inventory extracted with that new methodology with an in situ lamp inventory made for two villages in Canada. This will allow us to emphasize the strengths and limitations of the method by comparing to the ground truth.

Stray light is a critical aspect for high performance optical instruments. When stray light control by design is insufficient to reach the performance requirement, correction by post-processing must be considered. This situation is encountered for example in the case of the Earth observation in-strument 3MI, whose stray light properties are complex due to the presence of many ghosts dis-tributed on the detector array. We implement an iterative correction method and discuss its con-vergence properties. Spatial and field binning can be employed to reduce the computation time but at the cost of a decreased performance. Interpolation of the stray light properties is required to achieve high performance correction. For that, two methods are proposed and tested. The first interpolate the stray light in the field domain while the second applies a scaling operation based on a local symmetry assumption. Ultimately, the scaling method is selected and a stray light reduction by a factor of 58 is obtained at 2σ (129 at 1σ) for an extended scene illumination.

Light-addressable potentiometric sensor (LAPS) is an electrochemical sensor based on the field-effect principle of semiconductor. It is able to sense the change of Nernst potential on the sensor surface, and the measuring area can be controlled by the illumination. Due to the unique light-addressable ability of LAPS, the chemical imaging system constructed with LAPS can realize the two-dimensional image distribution detection of chemical/biomass. In this paper, the advantages of LAPS as sensing unit of microelectrochemical analysis system are summarized. Then, the greatest development of LAPS analysis system is explained and discussed. Especially, this paper focused on the research of ion diffusion, enzymatic reaction, microbial metabolism and droplet microfluidics by using LAPS analysis system. Finally, the development trends and prospects of LAPS analysis system are illustrated.

In the present paper, the so-called Einstein’s causality is scrutinized and proven to be an illusion, a sort of mathematical fallacy. Causality as a well-established universal principle was and is absolutely valid for subluminal, luminal and superluminal signals under any natural and/or artificial circumstances. It is also shown that conceptually special relativity theory (SRT) is inapplicable to superluminality of physical phenomena since SRThas the light speed in vacuum as an upper limiting speed in its own proper domain of applications, and also because SRT is crucially based on the concept of inertial reference frames (IRFs) which are related to each other by Lorentz transformations, that is why the relative velocity of any two IRFs must be smaller than light speed.

The aerosol optical depth is an important indicator of aerosol particle properties and associated radiative impacts. AOD determination is therefore very important to achieve relevant climate modeling. Most remote sensing techniques to retrieve aerosol optical depth are applicable to daytime given the high level of light available. The night represents half of the time but in such conditions only a few remote sensing techniques are available. Among these techniques, the most reliable are moon photometers and star photometers. In this paper, we attempt to fill gaps in the aerosol detection performed with the aforementioned techniques using night sky brightness measurements during moonless nights with the novel CoSQM: a portable, low cost and open-source multispectral photometer. In this paper, we present an innovative method for estimating the aerosol optical depth by using an empirical relationship between the zenith night sky brightness measured at night with the CoSQM and the aerosol optical depth retrieved at daytime from the AErosol Robotic NETwork. Such a method is especially suited to light-polluted regions with light pollution sources located within a few kilometers of the observation site. A coherent day-to-night aerosol optical depth and Ångström Exponent evolution in a set of 354 days and nights from August 2019 to February 2021 was verified at the location of Santa Cruz de Tenerife on the island of Tenerife, Spain. The preliminary uncertainty of this technique was evaluated using the variance under stable day-to-night conditions, set at 0.02 for aerosol optical depth and 0.75 for Ångström Exponent. These results indicate the set of CoSQM and the proposed methodology appear to be a promising tool to add new information on the aerosol optical properties at night, which could be of key importance to improve climate predictions.

Vision is our primary sense as the human eye is the gateway for more than 65% of information reaching the human brain. Today’s increased exposure to different wavelengths and intensities of light from Light Emitting Diodes (LEDs) sources could induce retinal degeneration and accompanying neuronal cell death. Damage induced by chronic phototoxic reactions occurring in the retina accumulates over years and it has been suggested to be responsible for the etiology of many debilitating ocular conditions. In this work, we examined how LED stimulation affects vision by monitoring changes in the expression of death and survival factors as well as microglial activation in LED-induced damage (LID) of the retinal tissue. We found an LED exposure-induced increase in the mRNA levels of major apoptosis-related markers -BAX, Bcl-2, and Caspase-3 and an accompanying wide-spread microglial and Caspase-3 activation. Everyday LED light exposure was accounted for all the described changes in the retinal tissue of mice in this study, indicating that overuse of non-filtered direct LED light can have detrimental effects on the human retina as well.

Improper illumination of cultural heritage buildings and monuments can be a source of enormous light pollution that can have a major impact on the overall environment of the illuminated area. Such lighting can be the result of carelessness or a wrong/badly designed lighting system. This paper presents one of the methodologies that can significantly reduce light pollution, especially the spilt light out of the façade. The methodology is based on using luminaires with specially made shutters with the appropriate silhouette of the object. The shutter is planned with the help of an object photo and sizes measured at the location. The methodology was tested during the renovation of the lighting system of different churches in Slovenia and is described in the example of the Church of St. Thomas near Ptuj, Slovenia. The results showed that the methodology is effective and can significantly reduce light pollution that occurs when such buildings are incorrectly lit.

A typical white-light light-emitting diode (LED) can achieve a sunlight-like spectral profile in the visible spectrum by means of using an optical filter, with an inverted transmission profile to the white LED, fabricated using a deposition coating process. The unfiltered white LED generates white light by mixing light emitted by a blue LED (450 nm) with emission from the yellow phosphorescence excited by the blue light and differs significantly from the characteristics of the full-spectrum natural light. In this study, the spectral characteristics of the filtered LED light can be improved to reach a general color rendering index value (Ra) of 95.6 at the D65.

The ternary Bi2MoO6-reduced graphene oxide (rGO)-TiO2 catalyst were synthesized using a simple hydrothermal method. The improvement of the photocatalytic decomposition efficiency of Bi2MoO6-rGO-TiO2 composite is 92.3% than the pure and binary photocatalyst. The effects of operational parameters like catalyst ratio, the different catalyst, different ratio rGO and different pH, have been analyzed. As prepared ternary photocatalyst is low Photoluminescence and high photocurrent density responsible, it exhibited that photon-induced electron and hole-recombination were suppressed and also charged separation is effective. The present study shows the rGO is an excellent electron transfer performance and enhanced the photocatalytic reaction stability.

The anodic polarization response of magnesium alloy AZ31 was characterized during exposure to aerated 0.1M NaCl solutions with millimolar additions of NaVO₃, Na₃PO₄, Na₂HPO₄, NaF and various pairings to assess their ability to inhibit corrosion kinetics and retard localized corrosion. Each of the candidate inhibitors reduced the corrosion rate of the alloy to some degree. A Na₃PO₄ - NaVO₃ pair produced a powerful inhibiting response decreasing the corrosion rate to about 10^-7 A/cm², which was two orders of magnitude lower than the uninhibited control case. A Bliss Independence assessment indicated that this inhibitor pair acted synergistically. A Na₂HPO₄ - NaVO₃ pair reduced the corrosion rate to 10^-6 A/cm² but was not assessed to be acting synergistically. The NaVO₃ - NaF pair did not reduce the corrosion rate significantly compared to the control case and was an antagonistic pairing. SEM imaging showed film formation due to exposure, which appears to be the origins of the observed inhibition. The resistance to localized corrosion was assessed as the difference in the breakdown potential and the corrosion potential with larger values indicating a lower probability of localized corrosion during free corrosion exposures. Effects of the inhibitors on this characteristic were mixed, but each of the inhibitor pairs yielded potential differences in excess of 100mV. A conceptual conversion coating process based on a mixture of vanadate and phosphate compounds were demonstrated. A fluoride-bearing formulation produced coatings whose total impedance was increased by a factor or 2 compared to an uncoated control. A fluoride-free formulation produced coatings whose corrosion resistance was increased by more than a factor of 3.

Background: Alzheimer’s disease (AD), the most threatening neurodegenerative diseases, is characterized by the loss of memory and language function, an unbalanced perception of space and other cognitive and physical manifestations. Pathology of the AD is characterized by neuronal loss, and the extensive distribution of senile plaques and neurofibrillary tangles (NFTs). The role of environment and the diet in the AD is being studied actively, and nutrition is certainly one of the main factors playing a prominent role in the prevention of neurodegenerative diseases. In this context, the relationship between dementia and wine use/abuse has received increased research interest in recent times, with varying and often conflicting results. Scope and approach: This review aims to critically summarize the most recent studies conducted to clarify the relationship between wine drinking and AD, as well as whether effects are influenced by quantity and/or frequency of drinking. Key findings and Conclusion: Overall, based on the interpretation of various studies, it can be concluded that there is no indication that light to moderate alcohol drinking is detrimental to cognition and dementia, and it is not possible to define whether alcohol could be used as a means to reduce risk of developing AD.

Much remains to be understood for delayed ultraweak photon emission (UPE) from organism in association with oxidative burst following external perturbation, a phenomenon that has been experimented for over three decades. Delayed UPE often decays hyperbolically; yet, it is not uncommon to have delayed UPE that reveals first-order kinetic patterns characterized by single-exponential, double exponential, or multi-exponential changes. Some delayed UPEs also presented transient patterns that are characteristic of second-order responses. A soliton-based photon-storage model has addressed the hyperbolic decaying pattern of delayed UPE; however, there are questions outstanding regarding modeling other non-hyperbolic kinetics as well as the large range of temporal scales of delayed UPE that can vary from 8.5 microseconds to many hours. This work proposes an alternative, phenomenological model-framework for interpreting the various kinetic patterns of delayed UPE following stress. The delayed UPE is considered to be governed by two sequential phases: a stress-transfer phase that transforms the external stress to photo-genesis for emitting photons, and a photon-diffusion phase that transmits the photons emitted by the photo-genesis to the surface of organism for being detected as delayed UPE. Time-resolved photon diffusion analysis reveals that any delayed UPE in organism with a delay time >100ns cannot be addressed by the inherent temporal spread that realistic tissue scattering will cause. A slow stress-transfer phase is thus required to explain the delay time-scales of delayed UPE at a minimum of 8.5 µs as reported experimentally. The stress-transfer phase is hypothesized to carry the following types of responses: single or multiple 1st-order low-pass, single 2nd-order low-pass with various damping factors, and single 2nd-order band-pass with various damping factors. A single 1st–order low-pass response with a time-varying kinetic rate is also analyzed. The responses of these modeled pathways to bolus and step inputs demonstrate that a kinetic pattern other than the exact single-exponential one may have multiple causes.

Three-dimensional (3D) imaging has attracted more and more interests because of its widespread applications, especially in information and life science. These techniques can be broadly divided into two types: ray-based and wavefront-based 3D imaging. Issues such as imaging quality and system complexity of these techniques limit the applications significantly, and therefore many investigations have focused on 3D imaging from depth measurements. This paper presents an overview of 3D imaging from depth measurements, and provides a summary of the connection between these the ray-based and wavefront-based 3D imaging techniques.

Nanoparticles -- regularly patterned or randomly dispersed -- are a key ingredient for emerging technologies in photonics. Of particular interest are scattering and field enhancement effects of metal nanoparticles for energy harvesting and converting systems. An often neglected aspect in the modeling of nanoparticles are light interaction effects beyond classical electrodynamics stemming from electron dynamics in confined and accelerated systems. We give a detailed account on free electron phenomena in metal nanoparticles and discuss analytic expressions, stemming from microscopic and semi-classical theories. These can improve standard computational schemes to produce more reliable results on the optical properties of metal nanoparticles. We combine these solutions into a single framework and study their joint impact on isolated Au, Ag, and Al nanoparticles as well as dimer structures.

Policing duties may inherently be dangerous due to stab, blunt trauma and ballistic threats. The addition of individual light armour vests (ILAVs) has been suggested as a means to protect officers. However, the addition of the extra load of the ILAV may affect officer ability to conduct occupational tasks. The purpose of this study was to determine if wearing any of 3 different ILAVs (ILAV A, ILAV B, & ILAV C) affected occupational task performance when compared to that in normal station wear. A prospective, within-subjects repeated measures design was employed, using a counterbalanced randomization in which each ILAV was worn for an entire day while officers completed a variety of occupationally relevant tasks. These tasks included a victim drag, car exit and 5 meter sprint, step down and marksmanship task. Results showed that performance in each task did not vary between any of the ILAV or normal station wear conditions. There was less variability in the marksmanship task with ILAV B, however. The results suggest that none of the ILAVs used in this study were heavy enough to significantly affect task performance in the assessed tasks when compared to wearing normal station wear.

Wildlands are increasingly lost to human development. Conservation scientists repeatedly call for protecting the remaining wildlands and expanding the land area protected in reserves. Despite these calls, conservation reserves can be eliminated through legislation that demotes their conservation status. For example, legislation introduced to the Congress of the United States recently would demote 29 Wilderness Study Areas (WSAs) from the protections afforded by their existing status. The legislation suggests that the 29 areas are not suitable for a promotion and future inclusion in the National Wilderness Preservation System based on decades-old local evaluations. Local evaluations, notwithstanding, it may be important to consider the value of lands from a national perspective. Without a national perspective, local evaluations alone may overlook the national significance of lands. With this in mind, I used five qualities of wildland value (wildness, light pollution, noise pollution, intactness of mammals, and intactness mammal carnivores of conservation concern) to compare the 29 WSAs to all national parks and wilderness areas located within the contiguous United States. The pool of 29 WSAs were similar to the pool of national parks and wilderness with respect to the five qualities assessed, and some of the WSAs were characterized by higher values than most of national parks and wilderness areas. This analysis demonstrates the national significance of the WSAs targeted for conservation status demotion. Such an approach could be used in future land management legislation and planning to ensure that a national perspective on conservation value is brought to bear on decisions facing federally-managed lands.

Due to the demands of personal travels and entertainments, light airplanes and small business aircrafts are developing rapidly. Light airplane structure is simple; however, it lacks crashworthiness design, especially the considerations on the impact of energy absorption. Therefore, in an event of accident, significant damage to passengers will be usually incurred. Airplanes made of composite materials structurally have high specific strength and good aerodynamic configuration. These materials have become the primary choice for new airplane development. This study mainly explores the topology optimization analysis of the light aircraft’s cockpit made of carbon fiber reinforced composites. This paper compares the compression amounts in the original models of composite material and aluminum alloy fuselages with the models after optimization during the crash-landing, in order to investigate the safety of fuselages made of different materials after structural optimization under the dynamic crashing. This study found that the energy absorbed by the aluminum alloy fuselage during crash-landing is still higher than that by the carbon fiber reinforced composites fuselage. On the other hand, the aluminum alloy fuselage after topology optimization could have an energy absorption capability enhanced by 40%, as compared to the that of the original model of aluminum alloy fuselage.

For esophageal cancer patients treated with neoadjuvant chemoradiotherapy (nCRT), restaging using F-18-fluorodeoxyglucose (18F-FDG) positron emission tomography computed tomography (PET-CT) following nCRT can detect interval metastases, including liver metastases, in almost 10% of patients. However, in clinical practice, focal FDG liver uptake, unrelated to liver metastases, is observed after chemoradiotherapy. This radiation-induced liver injury (RILI) can potentially lead to overstaging. Liver radiation damage is also a concern during distal esophageal cancer radiotherapy due to proximity to the left liver lobe, typically included in the radiation field. Post-CRT, if FDG activity appears in the left or caudate liver lobes, thorough investigation is needed to confirm or rule out distant metastases. The increased FDG uptake in liver lobes post-CRT often presents a diagnostic dilemma. Distinguishing between radiation-induced liver disease and metastasis is vital for appropriate patient management, necessitating a combination of imaging techniques and an understanding of the factors influencing radiation response. Diagnosis involves identifying new foci of hepatic FDG avidity on PET/CT scans. Geographic regions of hypoattenuation on CT and well-demarcated regions with specific enhancement patterns on contrast-enhanced CT scan and MRI are characteristic of radiation-induced liver disease (RILD). Lack of mass effect on all three modalities (CT, MRI, PET) indicates RILD. Resolution of abnormalities on subsequent examinations also helps in diagnosing RILD. Moreover, it can also help to rule out occult metastases, thereby excluding those patients from further surgery who will not benefit from esophagectomy with curative intent.

Over recent years, nanocarriers have played an ever-increasing role in clinical and biomedical applications owing to their unique physicochemical properties and surface functionalities. Lately, much effort has been directed towards the development of smart, stimuli-responsive nanocarriers that are capable of releasing their cargos in response to specific stimulus. These intelligent-responsive nanocarriers can be further surface-functionalized so as to achieve active tumor targeting in a sequential manner, which can be simply modulated by the stimuli. By applying this methodological approach, these intelligent-responsive nanocarriers can be directed to different target-specific organs, tissues or cells, and exhibit on-demand controlled drug release that may enhance therapeutic effectiveness and reduce systemic toxicity. Light, an external stimulus, is one of the most promising triggers for use in nanomedicine to stimulate on-demand drug release from nanocarriers. Light-triggered drug release can be achieved by light irradiation at different wavelengths, either in UV, visible or even NIR region, depending on the photophysical properties of the photo-responsive molecule embedded in the nanocarrier system, the structural characteristics and material composition of the nanocarrier system. In this review, we highlighted the emerging functional role of light in nanocarriers, with emphasis on light-responsive liposomes and dual-targeted stimuli-responsive liposomes. Moreover, we provided the up-to-date phototriggered targeting strategies and mechanisms of light-triggered drug release from liposomes and NIR-responsive nanocarriers. Lastly, we addressed the current challenges, advances, and future perspectives for the deployment of light-responsive liposomes in targeted drug delivery and therapy.

Spectrally weighed irradiance on the corneal plane is often used to determine the visual and non-visual potency of light. Spectral irradiance or illuminance is measured with a diffuser in the so-called 2π geometry (i.e., a hemispheric measurement). Due to anatomical conditions, the human binocular field of view (FOV) does not correspond to a hemisphere but is occluded upwards and downwards. FOV-restricted measurements are scarce, however, and thus the error when using hemispheric measurements is yet to be determined. For our study, we designed and 3D printed FOV occlusions as attachments to spectral measurement devices. Measurements with and without the occlusion were taken in different lighting situations in the laboratory (light from different directions) and in real-world conditions (light typically from above). Our measurements show a reduction of visual and melanopic values due to the FOV occlusion ranging from negligible to over 60% for realistic scenarios. Further, the reduction was comparable for visual and melanopic parameters, as the distribution of light in the FOV was generally spectrally homogeneous. In the case of an exemplary and artificial laboratory situation, however, the melanopic daylight (D65) efficacy ratio changed by more than a factor of 2 only due to the FOV occlusion. Finally, head orientation showed a marked impact on all quantities. Our results reveal the potential for considerable error when just evaluating and comparing vertical, hemispheric measurements in experiments and non-visual lighting design projects. We thus encourage the (additional) use of a FOV occlusion for eye-level measurements in typical viewing directions and provide open-source 3D-print files.

Earthquake-triggered landslides are one of the most significant hazards worldwide. These landslides, involving small or large volumes, can develop in debris flow or avalanche with high mobility and long-runout distance. The motion processes of this kind of landslide also quite complicated. This study reproduced the motion processes of two landslides using the LS-RAPID program. The Aso Bridge landslide occurred on April 16, 2016, with rapid and long-runout distance characteristics. The Kataragai landslide occurred on April 9, 2018, travelling with flow-like behavior. Through field investigations and laboratory experiments, features and mechanical parameters of these two landslides were obtained. In the LS-RAPID program, the pre-failure models and motion processes of these two landslides were established and reproduced. Results indicated that sliding speed and travelling morphology at different intervals were considered as two indicators to describe their motion process. However, while sliding speed of these two landslides have significant differences with sliding speeds of actual landslides, the final morphologies after failure were consistent with those observed in the field investigation.

Familial Mediterranean fever (FMF) is a systemic autoinflammatory disorder caused by inherited mutations in the MEFV (Mediterranean FeVer) gene located on chromosome 16 (16p13.3) and coding pyrin protein. Despite the existing data on MEFV mutations, the exact mechanism of their effect on the development of pathological processes leading to autoinflammation observed in FMF, remains unclear. Induced pluripotent stem cells (iPSCs) are considered an important tool for studying the molecular genetic mechanisms of various diseases due to their ability to differentiate into any cell type, including macrophages, which contribute to the development of FMF. In this study, we developed iPSCs of an Armenian patient with FMF having M694V, p.(Met694Val) (c.2080A&gt;G, rs61752717) pathogenic mutation in exon 10 of the MEFV gene. As a result of direct differentiation, macrophages expressing CD14 and CD45 surface markers were obtained. In addition, we found that the morphology of patient macrophages derived from iPSCs with MEFV mutation was significantly different from that of differentiated from iPSCs of a healthy donor carrying wild-type MEFV gene.

The exceptional performance of graphene has driven the advancement of its preparation technique and application. Laser-induced graphene (LIG), as a novel graphene preparation technique, has been applied in various fields. Graphene periodic structures created by LIG technique exhibit superhydrophobic characteristics and can be used for deicing and anti-icing applications, which are significantly influenced by the laser parameters. The laser surface treatment process was simulated by a finite element software analysis (COMSOL Multiphysics) to optimize the scanning parameter range, and the linear array surface structure were subsequently fabricated by the LIG technique. The generation of graphene was confirmed by Raman spectroscopy, and energy-dispersive X-ray spectroscopy. The periodic linear array structure were observed by Scanning electron microscopy (SEM) and confocal laser imaging (CLSM). In addition, CLSM testings, contact angle measurements, and delayed icing experiments were systematically performed to investigate the effect of scanning speed on surface hydrophobicity. The results show that the high quality and uniform graphene can be achieved using the laser scanning speed of 125 mm/s. The periodic linear array structures can obviously increase the contact angle and suppress delayed icing. Furthermore, these structures have the enhanced ability of the electric heating deicing, which can reach 100°C and 240°C within 15 s and within 60 s under the DC voltage power supply ranging from 3 to 7 V, respectively. These results indicate that the LIG technique can be developed to provide an efficient, economical, and convenient approach for preparing graphene and the hydrophobic surface array structure based on LIG has considerable potential for deicing and anti-icing applications.

The availability of multi-rotor UAVs with lifting capacities of several kilograms, allows for a new paradigm in atmospheric measurement techniques, i.e. the integration of research-grade sonic anemometers for airborne turbulence measurements. With their ability to hover and move very slowly, this approach yields an unrevealed flexibility compared to mast-based sonic anemometers, for a wide range of boundary layer investigations that require an accurate characterization of the turbulent flow. For an optimized sensor placement, potential disturbances by the propeller-induced flow (PIF), as well as the potential impact of the sensor weight and angular momentum on the flight performance in the case of a boom-mounted sensor, have to be considered.

Plant cells are omnipotent and breeding of new varieties can be achieved by protoplast fusion. Such fusions can be achieved by treatment with poly(ethylene glycol) or by applying an electric field. Microfluidic devices allow for controlled conditions and targeted manipulation of small batches of cells down to single cell analysis. To provide controlled conditions for protoplast fusions and achieve high reproducibility, we developed and characterized a microfluidic device to reliably trap few of Arabidopsis thaliana protoplasts and induced a cell fusion by controlled addition of poly(ethylene glycol) (PEG, with a molecular weight of 6000). Experiments were conducted to determine the survival rate of isolated protoplasts in our microfluidic system. Afterwards, PEG induced fusion was studied. Our results indicate that the following fusion parameters had significant impact on the fusion efficiency and duration: PEG concentration, osmolarity of solution, and flow velocity. PEG concentration below 10% led to only partial fusion. Osmolarity of the PEG fusion solution was found to strongly impact the fusion process; complete fusion of two source cells sufficiently took part in slightly hyper osmotic solutions, whereas iso-osmotic solutions led to only partial fusion at 20% PEG concentration. We observed accelerated fusion for higher fluid velocities. Up to this study, it was common sense that fusion is one directional, i.e. once two cells were fused into one cell they stay fused. Here, we present for the first time reversible fusion of protoplasts. Our microfluidic device paves the way to a deeper understanding on the kinetics and processes of cell fusion.

RNA, as an important substance for regulating biological growth and development, has significant implications for visualization research. However, many spontaneously fluorescent substances in plants greatly interfere with the effectiveness of plant bioimaging. Aggregetion- induced emission luminogens (AIEgens), due to their luminescent properties, tunable molecular size, high fluorescence intensity, good photostability, and low cell toxicity, have been widely applied in the animal and medical fields. We have found that AIEgens have great potential as RNA fluorescent probes for efficient imaging in plants. In this review, we first introduce several common RNA labeling forms and point out their pros and cons. We briefly describe the development of AIEgens and the AIE mechanism, and then present various practical applications of AIEgens, including detailed examples of their use as biological markers. To further promote the application of AIE in the field of RNA, we suggest the use of AIEgens to modify target RNA via techniques such as click chemistry or CRISPR/Cas, to achieve RNA visualization in plants. highly possible to modify target RNA with AIEgens in vivo for RNA visualization.

Laser-induced periodic surface structures (LIPSS) have gained significant attention due to their ability to modify the surface morphology of materials at the micro-nanoscale and show great promise for surface functionalization application. In this study, we specifically investigate the formation of LIPSS in silicon substrates and explore their impact on Surface-Enhanced Raman Spectroscopy (SERS) applications. This study reveals a stepwise progression of LIPSS formation in silicon, involving three distinct stages of LIPSS: 1) integrated Low-Spatial-Frequency LIPSS (LSFL) and High-Spatial-Frequency LIPSS (HSFL), 2) principally LSFL and 3) LSFL at the edge of the irradiated spot, elucidating the complex interplay between laser fluence, pulse number, and resulting surface morphology. Furthermore, from an application standpoint, these high-quality multi-scale periodic patterns lead to the next step of texturing the entire silicon surface with homogeneous LIPSS for SERS application. The potential of LIPSS-fabricated silicon substrates for enhancing SERS performance is investigated using thiophenol as a test molecule. The results indicate that the Au-coated combination of LSFL and HSFL substrate showcased the highest enhancement factor (EF) of 1.38 × 10^6. This pronounced enhancement is attributed to the synergistic effects of Localized Surface Plasmon Resonance (LSPR) and Surface Plasmon Polaritons (SPPs), intricately linked to HSFL and LSFL characteristics. These findings contribute to understanding LIPSS formation in silicon and their applications in surface functionalization and SERS, paving the way for sensing platforms.

The theory of electron spin has been proposed for a century, but the study of quantum effects in biological molecules is still in its infancy. Chirality-induced spin selectivity (CISS) is a very modern theory that can explain many biochemical phenomena. In this paper, we propose a new theoretical model based on CISS theory and quantum chemistry theory, which can well explain the theoretical explanation of the chiral selectivity of chiral proteins. Moreover, this theory can predict the spin state of corresponding chiral molecules. Taking L-DOPA and AADC enzyme as examples, this theoretical model solves the theoretical explanation of AADC enzyme's chiral catalysis selectivity problem and successfully predicts the spin state of L-DOPA and D-DOPA's valence electrons.