To support the integration of renewable energy sources and preserve grid stability, this study examines several approaches for controlling the temperature of Battery Energy Storage Systems (BESS) in modern energy settings. Specifically, the usage of BESS in Virtual Power Plants (VPPs) is the focus of this study. The effectiveness, safety features, dependability, affordability, and suitability for VPP applications of these systems are examined. Among the various hybrid cooling alternatives, two particularly promising combinations emerge. Firstly, the integration of heat pipes and phase change materials leverages their ability to conduct heat efficiently away from heat sources with minimal temperature differences, making them excellent for rapid heat transfer. Secondly, an approach employing heat pipes and liquid passive cooling a combination that capitalizes on the efficient heat transfer capabilities of heat pipes and the consistent cooling offered by liquid passive systems. The study underscores the importance of improving BESS performance and sustainability within VPPs by providing useful recommendations for choosing the best thermal management system depending on climate conditions and geographic location.

Deep eutectic solvents have emerged as a greener alternative and have attracted so much interest in the last two decades. This paper present alternative synthesis method to classical heating-stirring. The ultrasound method is one of the most promising syntheses DESs in terms of yield and energy. So, ultrasound synthesis method was studied to obtain hydrophobic (Aliquat 336: L-Menthol 3:7; Li-docaine: decanoic acid 1:2) and hydrophilic DESs based on Choline chloride and urea, ethylene glycol and oxalic acid. The physical characterization of DESs by comparison of FTIR spectra no show difference between DESs obtained by heating-stirring and ultrasound synthesis methods. The RMN spectra of the DESs obtained by heating-stirring revealed the DESs formation. Density and viscosity properties of DESs were evaluated. The density values are similar for both synthesis methods. However, lower viscosity values are obtained to the hydrophilic DESs prepared by ul-trasound methods.

Based on the goals of "high reliability, high frequency, rapid launch, and low cost" for space launch site, and drawing inspiration from the design principles of SpaceX's Starship launch test facility, an integrated dual-sided deflector system for convective cooling and thermal protection is presented. The interaction process between the gas jet and liquid water jet and its effect on the flow field environment are thoroughly studied using numerical calculation methods. Furthermore, Regarding the phase-change heat transfer issue in a compressible gas-liquid two-phase flow and the varying distribution of different bubble shapes and sizes at the gas-liquid interface, a modified Lee model is derived. The rationality and accuracy of the phase-change mass-transfer coefficient values can be improved by adjusting the equivalent diameter and shape factor of the bubbles. The research results demonstrate that compared to the classical Lee model, the modified Lee model can achieve a higher numerical accuracy in predicting the heat and mass transfer processes in gas-liquid two-phase flows. Through comparative analysis with traditional dual-sided deflector and conventional cooling system, the integrated dual-sided deflector system for convective cooling and thermal protection exhibits significant performance advantages in gas flow regulation, flow field environment improvement and erosion protection in the near-ground region of the launch site. Particularly, regarding the thermal environment of the dual-sided deflector, it not only achieves effective flow deflection, but also mitigates the degree of erosion caused by the gas jet on the deflector. This conclusion can provide theoretical references for the thermal protection design of commercial launch vehicle system at space launch site.

Addressing the issue of low bonding strength in Ti/Mg laminated composites due to interfacial oxidation, this study employs a differential temperature rolling method using longitudinal induction heating to fabricate Ti/Mg composite plates. The entire process is conducted under an argon gas protective atmosphere, which prevents interfacial oxidation while achieving uniform deformation. The effects of reduction on the mechanical properties and microstructure of the composite plates are thoroughly investigated. Results indicate that as the reduction increases, the bonding strength gradually increases, mainly attributed to the increased mechanical interlocking area and a broader element diffusion layer. This corresponds to a transition from brittle to ductile fracture at the microscopic tensile-shear fracture surface. When the reduction reaches 47.5%, the Ti/Mg interfacial strength reaches 63 MPa, which is approximately a 20% improvement compared to the bonded strength with previous oxidation at the interface. Notably, at a low reduction of 17.5%, the bonding strength is significantly enhanced by about 1 time. Additionally, it is found that a strong bonded interface at high reduction is beneficial in hindering the propagation of interfacial cracks during tensile testing, enhancing the ability of the Ti/Mg composite plates to resist interfacial delamination.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

This paper analyses the viability of different solutions to passively augment the axial stiffness of a horizontal axis radial levitation passive magnetic bearing (PMB) with topology previously studied. The zero-field cooling (ZFC) of high-temperature superconductor (HTS) bulks promotes higher magnetic impulsion and levitation forces and lower electromagnetic losses than with the field-cooling (FC), but on the other hand, the guiding stability is much lower than with FC. Because of stability reasons, FC was adopted in most superconducting maglev systems. The trend of this research group has been to develop an HTS ZFC horizontal axis radial levitation PMB presenting notable levitation forces with reduced electromagnetic losses, defined by a topology that creates guiding stability. Previous work has shown that even optimizing the bearing geometry to maximize magnetic guidance forces, could not be enough to guarantee the axial stiffness required for many applications. First, the extent to which guidance forces are augmented by increasing the number of HTS bulks in the stator is evaluated. Then, the axial stiffness augmentation by passively adding two limiting permanent magnet (PM) rings is evaluated. Results show that the axial stiffness is highly augmented by adding limiting PM rings with no significant additional investment. This change enables using the studied ZFC superconducting PMB in high-precision axial stability applications, such as precision gyroscopes, horizontal axis propellers and turbines.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

The amorphous Fe77Cu1Si13B9 ribbons were treated with pulsed laser interference heating (PLIH). It was confirmed here that the use of the laser heating process allowed for obtaining two-dimensional crystallised micro-areas, periodically distributed (at a distance of 17µm) on the surface of the amorphous ribbons. The correlation between structural changes (SEM, TEM, HRTEM) and the distribution of magnetic field lines of heated amorphous Fe77Cu1Si13B9 (FeCuSiB) ribbons is presented. Particular attention is paid to structure changes in micro-areas where, by controlling the laser interference heating process, partial crystallisation of amorphous alloys and the formation of clusters or single nanocrystallites (α-Fe(Si)) embedded in an amorphous matrix are given. The addition of copper to the FeSiB alloy promoted inhibition of grain growth. Electron holography of micro-areas confirmed shifts of the magnetic field lines in the areas of nanocrystallites, the presence of which in the structure caused magnetisation of the surrounding amorphous matrix.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Nepal, primarily an agricultural country, heavily relies on agricultural residue and fuelwood for daily energy requirements. In 2022, total energy consumption was 640 PJ, with traditional sources accounting for 64.17%, and fuelwood comprising 58.53% of total fuel consumption. The estimated potential supply of agricultural residue is 26 million tonnes, yielding about 442 million GJ of energy in 2021. Biomass trading often emphasizes volume or weight, necessitating a rapid and non-destructive assessment of energy properties for mutual benefit, aiding in the identification, management, and utilization of biomass sources. In this study, 200 biomass samples were collected in two batches (126 and 74 samples) from various locations in Nepal. Using Partial Least Squares Regression (PLSR), a model was developed correlating higher heating value (HHV) from a bomb calorimeter and spectral data from Fourier Transform near-infrared spectroscopy (FT-NIRS) (3595 – 12,489 cm-1) sensor. PLSR models incorporated raw spectra, eight preprocessing techniques, the multi-preprocessing five-range method, and a genetic algorithm. Outliers in the first batch were identified, and the first batch divided into an 80% calibration set and a 20% validation set, while the second batch was designated as an unknown sample set. The optimum PLSR model, utilizing first derivative preprocessing, improved accuracy by 6.77%, with coefficients of determination in the calibration set, validation set, and unknown set as 0.9694, 0.9578, and 0.8089, respectively. Root mean square errors were 132.4790 J/g, 189.4800 J/g, and 360.8845 J/g for the calibration set (RMSEC), validation set (RMSEP), and unknown set (RMSEUN), respectively. The prediction to deviation ratio (RPD) for the validation set and unknown set was 4.9 and 2.4, respectively. The cross validation model of combined sample data of every sets showed the R2CV of 0.95 and RPDCV of 4.6 indicating the model could serve as a reliable and swift non-destructive alternative for evaluating biomass HHV using NIRS and ready for updating for industrial use. However, incorporating a larger number of representative samples is crucial to enhance accuracy and develop a more comprehensive global model for predicting biomass HHV.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

The number of XLPE cables being used near or beyond their designed lifespan is increasing. The importance of timely cable replacement is increasing. Therefore, research is actively being conducted using VLF Tan δ diagnostic technology to assess the insulation condition of cables. There is a lack of studies measuring and analyzing VLF Tan δ of service aged XLPE cables. Additionally, there is a lack of research considering the operating environment. Therefore, research is needed to diagnose and analyze the insulation condition of the same serviced aged cable when it is operated in a different environment. This paper evaluates and analyzes the insulation condition of cables installed in the BFP, cooling tower, and deaerator booster pump of a combined heat and power plant. Each cable was analyzed by measuring VLF Tan δ, dielectric breakdown test of the cable, and tensile strength, elongation at break, crystallinity, and dielectric strength of XLPE specimens. Additionally, the correlation between VLF Tan δ and other characteristics was also analyzed. It was found that degradation progressed in the order of BFP, cooling tower, and deaerator booster pump. Therefore, it was confirmed that even for the same cable, deterioration varies depending on the installation location.

The main consequence of radiation damage on a Silicon-Photomultiplier (SiPM) is a significant increase in the dark current. If the SiPM is not adequately cooled, the power dissipation causes it to heat up, which in turn affects its performance based on the temperature. In order to investigate this heating effect, experiments were carried out using a KETEK SiPM glued on an Al2O3 substrate, as well as HPK SiPMs that were either glued onto an Al2O3 substrate or a flexible PCB. The assemblies were connected either directly to a temperature-controlled chuck on a probe station or through layers of materials with well-defined thermal resistance. A DC-mode LED was used to illuminate the SiPM, and the resulting SiPM current was measured to determine the steady-state temperature. This temperature depended on the power dissipated in the multiplication region of the SiPM and the thermal resistance. This information can be utilized to adjust the SiPMs working point, taking into account the effects of self-heating. Similarly, this approach can be applied to packaged SiPMs that have an unknown thermal contact to a heat sink.

An electrothermal analysis for barium titanate based ceramics is presented combining the Heywang–Jonker model for the electric resistivity with a heat dissipation mechanism based on natural convection and radiation in a one dimensional model on the device level with voltage as the control parameter. Both PTC and NTC effects are accounted for through the double Schottky barriers at the grain boundaries of the material. The problem formulated in this way admits uniform and non–uniform multiple steady state solutions that do not depend on the external circuit. The numerical bifurcation analysis reveals that the PTC effect gives rise to several multiplicites above the Curie point, whereas the NTC effect is responsible for the thermal runaway (temperature blowup). The thermal runaway phenomenon as a potential thermal shock could be among the possible reasons for the observed thermomechanical failures (delamination fracture). The theoretical results for the NTC regime and the thermal runaway are in agreement with experimental flash sintering results obtained for 3% and 8% yttria stabilized zirconia.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

In this paper, the experimental results of the thermal sub-system of a reliable and cost-effective polygeneration solar system are presented. This polygeneration system produces heating, cooling and electricity from solar energy, which are used in an existing test-building. Heat is generated in four evacuated tube solar collectors (ETC). The heat may be used for space cooling, through a variable geometry ejector (VGE) heat pump. In order to reduce the mismatches between generation and consumption, two thermal storage tanks were added. The performance of a new thermal storage, with 400 l, able to storage both sensible and latent heat, was tested. Heating performances of the test-building were assessed. Ejector cycle tests were also performed.

The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.

With the increasing demand for energy worldwide, researchers from different fields have been striving to improve the sustainability and proper utilization of energy resources. Passive radiative cooling, as a natural energy transport method, can achieve cooling without additional external energy input. This review provides a comprehensive examination of passive radiative cooling, including its fundamental theories and latest development. A particular emphasis is placed on the diverse range of fields where passive radiative cooling has been applied, notably including but not limited to construction and architecture. The current state of applications, potential challenges that may arise with wider adaption and promising research directions for each field are thoroughly discussed. This review underscores the universal applicability and feasibility of passive radiative cooling and contributes to its future development by identifying promising areas for further exploration.

Film cooling technology is of great significance to enhance the performance of aero-engines and extend service life. With the increasing requirements for film cooling efficiency, researchers and engineers have carried out a lot of work on the precision and digital measurement of cooling holes. Based on the above, this paper outlines the importance and principles of film cooling technology, reviews the evolution of cooling holes. Also, this paper details the traditional measurement methods of the cooling hole used in current engineering scenarios with their limitations and categorizes digital measurement methods into five main types, including probing measurement technology, optical measurement technology, infrared imaging technology, computer tomography(CT) scanning technology, and composite measurement technology. The five types of methods and integrated automated measurement platforms are also analyzed. Finally, through a generalize and analysis of cooling hole measurement methods, this paper points out technical challenges and future trends, providing a reference and guidance for forward researches.

The exceptional performance of graphene has driven the advancement of its preparation technique and application. Laser-induced graphene (LIG), as a novel graphene preparation technique, has been applied in various fields. Graphene periodic structures created by LIG technique exhibit superhydrophobic characteristics and can be used for deicing and anti-icing applications, which are significantly influenced by the laser parameters. The laser surface treatment process was simulated by a finite element software analysis (COMSOL Multiphysics) to optimize the scanning parameter range, and the linear array surface structure were subsequently fabricated by the LIG technique. The generation of graphene was confirmed by Raman spectroscopy, and energy-dispersive X-ray spectroscopy. The periodic linear array structure were observed by Scanning electron microscopy (SEM) and confocal laser imaging (CLSM). In addition, CLSM testings, contact angle measurements, and delayed icing experiments were systematically performed to investigate the effect of scanning speed on surface hydrophobicity. The results show that the high quality and uniform graphene can be achieved using the laser scanning speed of 125 mm/s. The periodic linear array structures can obviously increase the contact angle and suppress delayed icing. Furthermore, these structures have the enhanced ability of the electric heating deicing, which can reach 100°C and 240°C within 15 s and within 60 s under the DC voltage power supply ranging from 3 to 7 V, respectively. These results indicate that the LIG technique can be developed to provide an efficient, economical, and convenient approach for preparing graphene and the hydrophobic surface array structure based on LIG has considerable potential for deicing and anti-icing applications.

The spring-in phenomenon of the composite parts can affect the assembly process. This study aims to predict the spring-in phenomenon of carbon fiber reinforced plastic (CFRP) part. Here, we predict the spring-in of the CFRP part using a coupled analysis of the forming and cooling processes during the stamping process. First, a simulation of the entire forming process, such as the transfer of the composite laminate, gravity analysis, and forming was performed to obtain the temperature distribution of the CFRP part. Subsequently, a finite-element (FE) simulation of the cooling process was conducted to predict the spring-in phenomenon of the shaped CFRP part using the temperature data obtained in the forming simulation. Finally, a CFRP part was manufactured and compared with the results of the FE simulation.

The rapid development of electric vehicles, unmanned aerial vehicles, and wearable electronic devices has led to a high interest in research related to the synthesis of graphene with a high specific surface area for energy applications. However, the problem of graphene synthesis scalability, as well as the lengthy duration and high energy intensity of the activation processes of carbon materials, are significant disadvantages. In this study, a reactor was developed for the green, simple, and scalable electrochemical synthesis of graphene oxide with a low oxygen content of 14.1 %. The resulting material was activated using a fast joule heating method. The processing of mildly oxidized graphene with a high–energy short electrical pulse (32 ms) made it possible to obtain a graphene–based porous carbon material with a specific surface area of up to 1984.5 m2/g. The low energy intensity, simplicity, and use of environmentally friendly chemicals render the proposed method scalable.

Cooling fans are one of the critical components of air-forced (AF) dry-type transformers for regulating internal temperatures. Therefore, effective malfunction detection is crucial to maintain the transformer temperature within an acceptable range and prevent overheating. Regular maintenance occurs periodically and issues with cooling fans may arise between maintenance periods, leading to prolonged operation under malfunctioning conditions and potential failures. In addition, utilities typically have online information about whether a fan works or not without providing information about cooling fan malfunctioning circumstances. To address these challenges, this study proposes learning-based online monitoring techniques to detect malfunctions in AF transformer cooling fans. Random forests (RFs) and convolutional neural networks (CNNs) are developed to classify the audio signals from cooling fans into normal and malfunctioning classes. Unlike RFs, which require separate feature extraction, CNNs are trained based on spectrogram images derived from audio signals. Thus, various time-frequency techniques are utilized for feature extraction in RFs. Besides, multiple data augmentation techniques are employed to enhance the dataset size and diversity. Algorithmic performance is optimized through hyperparameter tuning and classifier threshold adjustment. Simulations reveal that CNNs outperform RFs, whereas the latter provides superior interpretability of acoustic features compared to the former.

This work presents a heat transfer and boiling model that computes the evolution of the temperature field in a representative steel workpiece quenched from 850 or 930°C by immersion in water flowing at average velocities of 0.2 or 0.6 m/s, respectively. Under these conditions, all three boiling regimes were present during cooling: stable vapor film, nucleate boiling, and single-phase convection. The model was based on the numerical solution of the heat conduction equation coupled to the solution of the energy and momentum equations for water. The mixture phase approach was adopted using the Lee model to compute the rates of water evaporation-condensation. Heat flux at the wall was calculated for all regimes using a single semi-mechanistic model. Therefore, evolution of boiling regimes at every position on the wall surface was automatically determined. Predictions were validated using laboratory results, namely: a) Videorecording the upward motion of the wetting front along the workpiece wall surface, and b) cooling curves obtained with embedded thermocouples in the steel probe. Wall heat flux calculations were used to determine the importance of the simultaneous presence of all three boiling regimes on the heat flux distribution. It was found that this simultaneous presence leads to high heat flux variations that should be avoided in production lines.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

The global energy landscape is undergoing a transformative shift, and the potential of LNG as a major energy source is a topic of intense debate. In order to meet the growing demand for sustainable energy supply, it is crucial to maximize the efficiency and environmental friendliness of the LNG supply chain. This research aims to leverage computational modeling and optimization techniques to enhance the production units involved in LNG production. By harnessing the power of advanced algorithms and simulations, we can identify and implement innovative strategies that minimize energy consumption, reduce greenhouse gas emissions, and enhance the overall sustainability of LNG. Through this study, we seek to uncover novel approaches to address the challenges faced by the LNG industry, including improving operational efficiency, optimizing liquefaction processes, and enhancing the utilization of natural resources. By integrating cutting-edge computational tools and considering environmental factors, we aspire to pave the way for a more sustainable and environmentally friendly future powered by LNG. By exploring the immense potential of computational modeling and optimization, we strive to contribute to the ongoing efforts in advancing energy sustainability and shaping the future of LNG as a crucial global energy source."In this paper, our focus is on simulating and optimizing the process of converting natural gas to LNG. Our goal is to achieve the minimum energy consumption per ton of LNG produced. Through our research, we have identified that utilizing a three-stage exchanger is the most effective approach for minimizing energy consumption in an LNG industrial production unit. Moreover, we have discovered that the outlet pressure from the compressor and the type of refrigerant in the cooling system play significant roles in determining the rate of energy conservation. By carefully considering these factors and optimizing their settings, we can further enhance the overall energy efficiency of the LNG production process. Our research aims to provide valuable insights and guidance to industry professionals and decision-makers in the LNG sector. By implementing the findings of this study, we can contribute to the sustainable development and utilization of LNG as a cleaner and more environmentally energy source. Friendly It's great to see the optimized parameters for the refrigerants and pressure settings in the liquefaction and subcooling cycles. With the mass fraction of 0.89 for methane and 0.14 for ethane in the liquefaction cycle, and 0.59 for methane and 0.3 for nitrogen in the composition for achieving energy efficiency in the LNG production subcooling cycle, The optimized outlet pressure of 650 kPa for the compressors in the liquefaction cycle and 1800 kPa for the subcooling cycle furtherr ccontribute to minimizing energy consumption. Based on your findings, the amount of consumed energy at 14.81 kW per ton of produced LNG highlights the success of the optimization efforts. Reducing the energy consumption per ton of LNG produced is a significant accomplishment towards achieving energy sustainability and environmental friendliness in the LNG industry. These results demonstrate the importance of computational modeling and optimization in identifying the best parameters for eenhancing energy efficiency in LNG production. By implementing these optimized settings, we can work towards a more sustainable future with reduced energy consumption and lower environmental impact

The microstructure evolution of SCM435 cold heading steel at different cooling rates was investigated by means of scanning electron microscopy, TEM, XRD, and electron backscatter diffraction. The results show that the cooling rate has a significant effect on the microstructure of the experimental steel. With an acceleration of the cooling, the microstructure of the steel gradually changed from ferrite and pearlite to ferrite, pearlite, and granular bainite; finally, the pearlite disappeared, and the microstructure changed to acicular ferrite, bainite, and martensite. With an increase in the cooling rate, the morphology of the carbide underwent an evolution from sheet carbide to short-rod carbide, granular carbide, and ultimately thin-strip carbide. With the acceleration of cooling, the proportion of large-angle grain boundaries gradually decreased, and the area of small-angle grain boundaries gradually increased. When the cooling rate was 0.1℃/s, the proportion of large-angle grain boundaries was as high as 52.8%, and the dislocation density was only 1.91 × 1012 cm−2. When the cooling rate was 2.0℃/s, the proportion of large-angle grain boundaries was only 27.1%, and dislocation density increased to 5.38 × 1012 cm−2. With the increase in the cooling rate, the depth of the decarbonization layer and the thickness of the scale oxide gradually decreased, the proportion of FeO phase in the scale phase gradually decreased, and the proportion of Fe3O4 phase and Fe2O3 phase gradually increased. The tensile strength increased monotonously with the increase in cooling rate, whereas the elongation and shrinkage first decreased, then increased, and then decreased. When the cooling rate was 1.0 m/s, the short rod and granular bainite in the material structure endowed the SCM435 steel with excellent strength and toughness matching, and the tensile strength and elongation of the steel reached 895 MPa and 24%, respectively.

Commercial buildings situated in hot and humid tropical climates rely significantly on cooling systems to maintain optimal occupant comfort. A well-accurate day-ahead load profile prediction plays a pivotal role in planning the energy requirements of cooling systems. Despite the pressing need for effective day-ahead cooling load predictions, current methodologies have not fully harnessed the potential of advanced deep-learning techniques. This research paper aims to address this gap by investigating the application of innovative deep learning models in day-ahead hourly cooling load prediction for commercial buildings situated in tropical climates. A range of deep learning techniques, including Deep Neural Network, Convolutional Neural Networks, Recurrent Neural Networks, and Long Short-Term Memory networks are employed to enhance prediction accuracy. Furthermore, these individual deep learning techniques are synergistically integrated to create hybrid models, such as CNN-LSTM and Sequence-to-Sequence models. An extensive comparative analysis is conducted to identify the most effective hybrid model. Sequence-to-sequence model provided better performance compared to the other single and hybrid models. Experiments are conducted to choose the time horizons from the past that can serve as input to the models. Further, the influence of various categories of input parameters on prediction performance has been assessed. Historical cooling load, calendar features and outdoor weather parameters are found in decreasing order of influence on prediction accuracy. This research focuses on buildings located in Singapore and presents a comprehensive case study to validate the proposed models and methodologies.

Domestic heating systems in the UK and across northern Europe are responsible for a substantial fraction of their countries’ carbon footprints. In the UK the vast majority of home space heating is via natural gas boilers with ’wet’ hydronic radiator systems. Most of those use TRVs (Thermostatic Radiator Valves) to avoid overheating, improve comfort and save energy. To meet Net Zero targets 20 million such UK gas systems may be retrofitted with heat pumps. Heat pump system designers and installers are cautious about retaining TRVs in such retrofitted systems in part because of worries that TRV temperature setbacks that lower heat demand may actually raise heat pump electricity demand in a "bad setback effect", thus wasting energy. This paper presents a new view of heat pump control and provides the first exploration of this issue, modelling one such industry claim, and finds that though real it should not apply to typical UK retrofits with weather compensation. The energy efficiency benefits of TRVs for older and partly-occupied homes, and to keep bedrooms cooler, remain valid. Comfort-seeking householders and installers should know that setting ’stiff’ temperature regulation may invoke the bad setback effect and cost dearly in energy and carbon footprint.

This article couples human metabolic factors and heating environmental factors, and uses a 57 node human thermal physiological model to study the heating effect of radiators. It provides a way to objectively calculate and directly quantify the effect of heating equipment on human thermal physiological parameters. As the inlet speed increases, the surface temperature of the human body first increases and then decreases. At a speed of 3m/s, it basically reaches a high value. Continuing to increase the wind speed, as the indoor convection intensity further increases, the surface temperature of the human body will decrease, leading to a decrease in thermal comfort. Compared with floor radiation heating under similar indoor temperature conditions, forced convection radiator heating has similar skin temperatures in various parts of the human body after the indoor design temperature exceeds 20 ℃, and the overall thermal comfort of the two technical solutions is equivalent. Research has shown that the turbulence wind speed of convective radiators should not be too small, with a wind speed range of 2.5m/s to 3m/s. The heating effect of using horizontal air outlet from the lower part of the radiator is better than that of vertical air outlet from the upper part. Convection type radiator heating is more suitable for buildings with rooms that are not too high due to the large indoor temperature gradient.

Traditional methods of non-metallic materials joining for industrial uses are limited to lasers, or induction or conduction heating. The precision and efficiency for large-scale applications are difficult to be achieved at the same time. Here in this paper, we report a precise microwave welding method induced by localized surface plasmon of metallic macro-gaps under microwave excitation. The proposed method utilizes energy from well-developed commercial microwaver, and benefits from the precision of localized surface plasmon, an oscillating electron cloud excited by electromagnetic waves, which is currently under hot investigation only at micro- or nano-scales. The method is applied to the welding of polymers to solve the problems of complex processing equipment and high processing energy consumption in the traditional welding process, so as to cope with the growing energy and environmental crisis. Finite element numerical simulations are used to study the distribution characteristics of electric fields and temperature fields. The results show that the process is a high quality, efficient, low consumption and environmentally friendly green process compared to traditional polymer welding methods.

Cirrus thinning, as one kind of geoengineering approach, not only cools our planet but also enhances the amount of sunlight reaching Earth's surface (brightening effect). This study delves into the brightening effect induced by cirrus thinning with a flexible seeding method. The thinning of only cirrus clouds results in a considerable globally averaged cooling effect (−2.46 W m−2), along with a notable globally averaged brightening effect (2.19 W m−2). Cirrus thinning also results in substantial reductions in the cloud radiative effects of the lower mixed-phase and liquid clouds. While these reductions counteract the cooling effect from cirrus clouds, they enhance the brightening effect from cirrus clouds. Consequently, the brightening effect caused by cirrus seeding (4.69 W m−2) is considerably more potent than its cooling effect (−1.21 W m−2). Furthermore, due to the more pronounced changes from the mixed-phase and liquid clouds at low- and mid-latitudes, the cooling effect is primarily concentrated at high latitudes. In contrast, the brightening effect is significantly stronger over most low- and mid-latitude regions. Overall, cirrus thinning could lead to a notable brightening effect, which can be leveraged to offset the dimming effect (the opposite of brightening effect) of other geoengineering approaches.

The development of biofortified and stress tolerant common bean lines contribute to counteract micronutrient malnutrition in the current condition of climate variability. Our objective was to evaluate the adaptive responses of biofortified common bean (Phaseolus vulgaris L.) lines under acidic soils and high temperature stress conditions in the Amazon region of Colombia. Adaptive responses were evaluated based on phenological, physiological and agronomic differences under combined stress conditions. A total of 247 common bean lines from the Mesoamerican gene pool were evaluated under field conditions at Florencia, Caquetá, Colombia. The common bean lines evaluated included 146 from F4 families with high iron (Fe) content and 99 common bean lines from F5 families that were obtained from simple crosses, double crosses and backcrosses among different bean lines. Lines with tolerance to combined stress conditions of acidic soil and high temperature were found with grain yields greater than 1,400 kg ha-1 from the F5 (lines: 859, 805, 865, 657) and F4 (lines: 2853, 2796) families. This improved agronomic response is likely due to the greater partitioning of photosynthates from canopy biomass (CB) toward pod formation (pod partitioning index, PPI) and grain filling (pod harvest index, PHI; harvest index, HI), which translated into higher grain yields (GY). GY was correlated with CB (r = 0.36), PPI (r = 0.6), PHI (r = 0.68), and HI (r = 0.8, P<0.001). The physiological responses that contributed toward superior agronomic performance of biofortified common bean lines include greater allocation of energy to the photosynthetic machinery (ΦII) and its dissipation in the form of heat (ΦNPQ) as the leaf temperature differential (LTD) increased under combined stress conditions. Six biofortified common bean lines (F5 lines: 859, 805, 865, 657; F4 lines: 2853, 2796) were identified with multiple stress resistance traits and these lines can serve as parents for further genetic improvement of common bean for multiple stress tolerance in the Amazon region of Colombia.

This paper proposes a simulation technique for investigating the battery thermal management system based direct refrigerant cooling (BTMS-DRC). It employs finite element method for a combined-conduction-convection heat transfer to predict the module temperature and to prove the temperature uniformity. The refrigerant side cooling is based on the two-phase flow evaporation which is represented by the convection heat transfer (flow evaporation) under a certain refrigerant saturation temperature. The battery heat generation is modeled as the constant heat flux. The main module is modeled as the conduction heat transfer. The real BTMS-DRC is constructed for experimentation with the test bench which is based on the dual-evaporators vapour compression refrigeration system. The simulated result is validated with the experimental results to ensure the correction of the modelling. The simulation also investigates the impact of the heat generation, convection heat transfer coefficient, refrigerant saturation temperature, and thermal conductivity on the module temperature and temperature uniformity. It is found that the simulated results agree well with the experimental results. The errors are around 2.9 - 7.2% throughout the specified working conditions. Overall, the proposed technique can be used as a design tool for further developing the BTMS-DRC.

The present state of the natural environment is significantly influenced by the construction sector. Due to the large amounts of consumed natural resources and materials as well as the high volume of emitted pollutants, the building industry is considered to have a key influence in achieving a global sustainable development. A considerable part of the ecological impact of the built environment is influenced by the energy consumed for creating appropriate indoor conditions as well as by the greenhouse gases that are emitted during the operation stage of a building’s life cycle. Therefore, the energy performances of existing buildings must be significantly improved in the near future. This paper analyzes the influence of the thermal insulation thickness of walls on the linear thermal transmittances and the heating demand of an existing building. The resulted values show that while increasing the insulation of the walls leads to a serious heat demand reduction, a deep renovation of the building cannot be achieved solely by using this solution.

The effects of the coolant pulsation and the film cooling with the plasma aerodynamic actuation (PAA) could be herein explored via large eddy simulations. The electrohydrodynamic force derived from the PAA was solved through the phenomenological plasma model. The Strouhal number of the sinusoidal coolant pulsation and the averaged pulsation blowing ratio were 0.25 and 1.0, respectively. Comprehensive analyses were carried out on the time-averaged flow fields, and the results revealed that the pulsed cooling jet might cause a deeper penetration into the crossflow, and this phenomenon could be remarkably mitigated by the downward force of the PAA. Furthermore, because of the coolant pulsation, the counter rotating vortex pair (CRVP) expanded to lifted off the wall less well, and the PAA lessened the negative lift-off impact and entrapment from the CRVP. Then, the spatial-temporal development of the coherent structures was figured out by the alterations of the centerline temperature, reflecting formation of the intermittent coherent structures rather than hairpin vortices due to the coolant pulsation, and their size and upcast behaviors were reduced by the PAA. Consequently, there was a basic suppression of the turbulent mixing of the cooling fluid with the crossflow. Finally, the three-dimensional streamlines confirmed that the coherent structure dynamic behaviors were significantly regulated by the PAA for alleviating the adverse influences of the coolant pulsation. In summary, through controlling how the dominating coherent structures evolve throughout time and space, the PAA can effectively increase the pulsed film cooling efficiency.

: Clay covers a substantial portion of the Earth. Such soil covers Iraq’s central and southern regions, where the depth of the clay may reach 150 m. All enhancement techniques and methods for transporting large loads cease to function or become prohibitively expensive in such soils. In this case, thermal treatment is the most effective method. In this study, a novel heating system was created and produced utilizing gas as the heat source via boreholes that simulate reality. The borehole heating cases were planted inside soft clay soil to enhance the soil. Different parameters were investigated, including the spacing between boreholes (3, 4, and 5 times the outer diameter of the borehole), the heating depth (1, 1.5, 2, and 2.5 times the width of the model footing), the duration of heating (2, 4, 6, 8, and 10 hrs), and the pattern (square, circular, triangular). The results showed the strength and behavior of the soil treated with heated boreholes at varying spacings, depths, patterns, and heating periods. The best results were found for a spacing, depth, and heating time of three times the outer diameter of the borehole, two times the width of the footing model, and eight hours, respectively. The effect of the heated borehole casing pattern was small when the heated borehole casing was used. The experiments conducted on heated soil showed that the undrained shear strength (Cu) increased from 14 to 360 kPa and then dropped to 140 kPa (as an average with depth). In contrast, the average angle of internal friction (Ø) rose from 0 to 52 degrees and decreased to 16 degrees (as an average with depth) from the center of the heating model to the furthest point affected by heating. In addition, the EDS pattern showed that components like silicon, aluminum, and iron dropped at 300 °C and rose at 400 °C in the treated soils. At 200 °C, the calcium content rose, and then dropped dramatically at 400 °C. The carbon percentage increased at 300 °C and decreased at 400 °C. The elements’ proportions showed little change or remained stable at temperatures between 400 °C and 600 °C.

This research aims to delve into the intricacies of combustion processes, specifically focusing on heating oil and a blend of heating oil with TPO (Tire Pirolysis Oil) in a self-developed evaporative combustion chamber featuring steam injection. The primary objective is to scrutinize the impact of steam injection on the combustion dynamics. Conducting a series of tests, the investigation involved the meticulous manipulation of stoichiometric ratios while introducing ambient air through gravity fuel flow. Subsequent iterations of these tests incorporated the introduction of steam into the ambient air stream. The examination encompassed the combustion of both heating oil and the TPO blend within the combustion chamber. The evaluation criteria comprised an in-depth analysis of flame characteristics, temperature distribution within the combustion chamber, and the quantification of emissions such as particulate matter (PM), nitrogen oxides (NOx), carbon dioxide (CO2), carbon monoxide (CO), and water vapor (H2O). Throughout the experimentation phase, commercially available diesel fuel served as the primary fuel source. To facilitate the tests, the combustion chamber under scrutiny was seamlessly integrated into an AVL engine test bench system. Essential parameters, including fuel consumption, were meticulously gauged using an AVL 735 fuel flow meter, while fuel temperature was monitored using the AVL 745 fuel temperature conditioning system. The intake air, a crucial element in the combustion process, was quantified with precision using an AVL Flowsonix sensor. Emission measurements were conducted meticulously using state-of-the-art equipment, with gaseous emissions analyzed using an AVL FTIR AMA i60 exhaust gas analyzer. Simultaneously, soot emissions were quantified through employment of an AVL Micro Soot sensor. This comprehensive approach not only delves into the fundamental aspects of combustion but also extends its reach to the exploration of innovative techniques, such as steam injection, to enhance combustion efficiency and reduce emissions. The integration of advanced measurement tools ensures a robust and thorough analysis of the combustion process and its environmental implications.

Finnish government's carbon neutrality goal by 2035 requires integration of renewable energy sources into the power grid. Considering the stochasticity of these resources, additional sources of flexibility are necessary to balance supply and demand in the power grid. District heating network (DHN) operators in Finland plan to shut down fossil-fuel-based combined heat and power plants and electrify heating systems by deploying heat pumps (HPs) and electric boilers. Techno-economic analysis and optimal operation of DHN-connected HPs and electric boilers in providing ancillary balancing services considering the 15-minute granularity in the balancing markets in Finland were investigated. The objective was to maximize the potential revenue for DHN operators gained from the day-ahead electricity market and frequency containment reserve (FCR) balancing markets. Three inter-connected DHNs in the Helsinki metropolitan area were optimized considering the reference year 2019 and each operator's decarbonization strategies for 2025. HPs could gain the highest profit from FCR-D up-regulation market, while the electric boiler may gain considerable profits from FCR-D down-regulation market. Compared to other balancing markets studied, the FCR-N market had a limited profit margin. Sensitivity analysis indicated that spot electricity prices and CO2 emission allowance prices have a significant impact on the profit from balancing markets.

A hydrothermal technique with microwave heating (200 °C, 2 hours, 2 magnetrons, 2.45 GHz) was modified to obtain UV-C luminescent LaPO4: Pr3+ colloidal nanorods for the potential use in X-ray cancer theranostics. For further possible biofunctionalization, a compound of tartaric acid formed under basic conditions was used as a coating and stabilizing agent to provide colloidal properties to the surface of nanoparticles in basic to neutral aqueous media, which was confirmed by zeta potential measurements. In addition, the colloidal properties and clustering processes of synthesized LaPO4:Pr3+ nanorods in aqueous solutions with different pH values were studied in real time using a highly sensitive laser ultramicroscope operating according to the “light-sheet” scheme. A comparative analysis of the transmission electron microscopy, X-ray powder diffraction and high-energy spectroscopy showed the different effects of synthesis parameters on the morphological, crystalline and luminescent properties of the obtained nanorods. Through optimization of the synthesis parameters, stable aqueous solutions of m-LaPO4:Pr3+ nanorods with sizes less than 30 nm and an intensity of UV-C luminescence equal to 5-10% of the unmodified nanofibers were obtained.

Due to an urgent need for reducing the fast progressing climate changes, a rapid, standardized and replicable solution for the infrastructure restructuring of heat demand coverage of buildings at district and city level must be developed. As more and more communities in Europe, especially in Germany, are obligated to have plans for coverage of heat demand, city planners, energy agencies seek a tool, which will help them to design the first drafts of heating network routes, which can supply whole districts and cities with renewable energy. ArcGIS Pro Tools like Least-Cost-Path-Analysis (LCPA) and Closest Facility (CF) allow to find the shortest and “cheapest” way between the heat source and heat consumers in the analyzed areas. Starting from the community level, through the district, county, voivodeship and whole country levels, the replication of the methods for generating district heating (DH) network infrastructure can be achieved. The proposed LCPA and CF based methods help to design the most suitable and efficient DH networks in the analyzed areas. As only few open-source data input, like street networks and building footprints are needed, the methods can be implemented in all communities of the country of Poland. In this paper one example of one community of Wroclaw county, called Siechnice and surroundings is presented.

Ultra high molecular weight polyethylene (UHMWPE) is a thermoplastic high-performance polymer in high demand for biomedicine, ship and machine building, anthropomorphic robots and smart prostheses. Highly oriented UHMWPE fibers possess record specific strength and may also be used for the fabrication of self-reinforced PE-PE composites (SRPEC). The temperature evolution study of the small-angle X-ray scattering (SAXS) signature of the supramolecular structure of UHMWPE can help reveal their important role in the mechanism of the shape memory effect in SRPEC. The laboratory SAXS–WAXS beamline XEUSS 3.0 was used for in situ studies of the nanostructure parameters in unidirectional SRPEC. Namely, the radius of gyration and the dimensionality factor were extracted from 2D SAXS patterns using several fitting algorithms. Significant changes of these parameters occurred in temperature ranges that correspond to the initiation of the shape memory effect and melting. The relationship between the material anisotropy and 2D SAXS patterns are discussed in the context of the supramolecular structure evolution.

The physical and mechanical properties of rocks will change significantly after being subjected to high temperatures, which poses safety hazards to underground projects such as coal underground gasification. In order to investigate the effect of temperature on the macroscopic and microscopic properties of rocks, this paper has taken sandstone as the research object and conducted uniaxial compression tests on sandstone specimens at different temperatures (20-1000 ℃) and different heating rates (5-30 ℃/min) at 1200 ℃. At the same time, the acoustic emission (AE) test system was used to observe the acoustic emission characteristics of the rock damage process, and the microstructural changes after high temperature were analyzed with the help of a scanning electron microscope (SEM). The test results show that the effect of temperature on sandstone is mainly divided into three stages: Ⅰ (20-500 ℃) stage is the strengthening zone, the evaporation of water and the contraction of primary fissures, sandstone densification is enhanced. Specifically, the compressive strength and elastic modulus increase, the macroscopic damage mode is dominated by shear damage, and the fracture micro-morphology is mainly brittle fracture. Stage II (500-600°C) is the transition zone, 500°C is the threshold temperature for compressive strength and modulus of elasticity, and the damage mode changes from shear to cleavage damage, and the sandstone undergoes brittle-ductile transition in this temperature interval. Stage III is the physicochemical deterioration stage. The changes in physical and chemical properties make the sandstone compressive strength and modulus of elasticity continue to decline, the macroscopic damage mode is mainly dominated by cleavage damage, and the fracture microscopic morphology is more toughness fracture. The effect of different heating rates on the mechanical properties of sandstone was further studied, and it was found that the mechanical properties of the rock were more deteriorated under higher heating rates.

Artificial intelligence algorithms have gained widespread adoption in the field of air conditioning load prediction. However, their prediction accuracy is substantially influenced by the quality of training samples. Training samples that lack relevance to the predicted moments can introduce interference into the neural network's learning process, potentially leading to a state of local convergence during its iterative process. This, in turn, diminishes the robustness and generalization capabilities of the prediction model. To enhance the prediction accuracy of air conditioning load prediction models based on artificial intelligence algorithms, this study presents an artificial intelligence algorithm prediction model based on the method of sample similarity sample screening. Initially, the comprehensive similarity coefficient between samples is computed using the gray correlation analysis method, enriched with enhancements in information entropy. Subsequently, a subset of closely related samples is extracted from the original dataset and employed as the training dataset for the artificial intelligence prediction model. Finally, the trained artificial intelligence algorithm prediction model is deployed for air conditioning load prediction. The results illustrate that the method of screening training samples based on sample similarity effectively improves the prediction accuracy of BP neural network (BPNN) and extreme learning machine (ELM) prediction models. However, it is important to note that this approach may not be suitable for genetic algorithm BPNN (GABPNN) and support vector regression (SVR) models.

The transition of the energy system to renewable sources means the cheap energy storage in fossil fuels must be replaced by other options. A large part of the demand for useful energy is heat and cold, often produced from electric energy by a resistance heater, compression heat pump or cooler. The question is then to store the initial electric energy by electric energy storage (EES) or the useful energy by thermal energy storage (TES). In a desktop study both options were compared, by the choice made in existing applications, and also generally analyzing current technology data. For the latter, cost, round-trip efficiencies, life cycles and life time of EES, specifically for batteries, and of TES, specifically for hot and cold water, ice and other PCM were collected. Applications studied are heating and cooling in buildings and in industry. Application-typical conversion efficiencies were also collected and taken into account. The results show that in many existing installations TES, incl. by PCM, is already preferred, and that TES is advantageous in most investigated applications economically, in addition to technical advantages. Thus, TES has a large potential in the transition of the energy system to stabilize the electricity grid by demand side management.

To study the heat and mass transfer characteristics of an evaporative cooler for cooling high-temperature working fluids such as supercritical carbon dioxide, an experimental device of the evaporative cooler was built, and a corresponding test system was constructed. Then, the experimental study was carried out based on the orthogonal test method, and the law and extent of the influence of water flow in the tube, spray water flow rate, inlet water temperature in the tube, and air flow rate on heat dissipation, cooling efficiency, and heat and mass transfer coefficients have been obtained. The correlation equations of the heat and mass transfer coefficients were obtained by fitting the orthogonal experimental data, and the validity of the correlation equations was confirmed by the verification experiment.

Thermal analysis of a hypereutectic Al-Si alloy used for an automotive part was carried out in this research work. Solidification characteristics are recognized from the Temperature-time curve and its corresponding derivatives. This analysis was successfully used in a simulation software program with the aim of improving the resultant simulation accuracy. In this study, different types of molds, with and without cooling systems, were designed and used. The melt present in the furnaces of the factory was used to simulate the casting process. The effect of different cooling rates (1.2ºC/s, 2ºC/s, 2.3ºC/s and 2.9ºC/s) on the solidification parameters have been investigated. Differences in the resultant microstructure between wall and center of the molds have been analyzed and have been related to the T-t curve. Finally, the experimental results clearly indicate that the water-cooling rate of the molds and the melt temperature directly affects the solidification process as well as the final microstructure.

The German government's ambitious goal of achieving CO2-neutrality by 2045 has prompted a focus on improving building insulation as a vital step toward energy efficiency. However, in this process, existing radiators and boilers are often left unchanged, leading to inefficiencies due to oversized heating systems. This paper presents various approaches to reduce the required radiator inlet temperature, drawing on data from 100 multifamily buildings. The approaches include heat reserve reduction, heat power shifting, uniform radiator usage, and heat requirement analysis. These approaches collectively aim to lower flow temperatures and decrease peak heat loads, reducing energy consumption, and minimizing waste in compliance with the user comfort temperature. The findings reveal that the application of these methods can lead to substantial temperature reductions, with an average decrease of 20.82 K and 7.28 K for the highest necessary flow temperature in the provided example. Furthermore, peak load reductions of 21.07% and 13.65% were achieved, demonstrating the potential to enhance energy efficiency. While each approach can be applied individually, their synergistic implementation can highly increase the efficiency of water to x heat pumps, due to the lower required flow temperatures.

A Gem-quality rubies and sapphires are often commercially heat treated at about 800°C or higher temperatures to enhance their colour and clarity, and hence quality. For this study, selected corundum samples containing diaspore- and goethite inclusions were heated step-by-step to a maximum of 1000 °C with the aim to monitor the dehydration and phase transformation of these oxyhydroxides to corundum and hematite during heating. Based on our experiments and in agreement with literature, the dehydration of diaspore in corundum occurs between 525 to 550 °C, whereas goethite transforms to hematite already between 300 and 325 °C. As both, diaspore and goethite are common inclusions in rubies, sapphires, and other corundum varieties, these dehydration reactions and phase transformations can be considered important criteria to separate unheated stones from heated ones, specifically in cases in which other methods (e.g. microscopy, FTIR) are unsuccessful.

: In the automotive industry, high-strength plates have been increasingly used to reduce the vehicle body weight due to stringent regulations on fuel economy and safety. Such plates achieve tensile strengths as high as 1.5 GPa owing to the hot-stamping process. However, these plates suffer from scale generation and surface decarburization because of the surface oxidation of the material. Recently, studies on materials subjected to high-frequency induction heating have reported strength improvement owing to the coil shape and cooling method. This study presents the surface temperature changes, mechanical properties, and microstructures of boron steels subjected to longitudinal heating, which uses eddy currents generated from high-frequency induction heating. The surface temperature data were analyzed under different high-frequency induction heating powers (15, 18, 21, 24, 27, and 30 kW) and distances from the specimen (6, 9, and 15 mm). The mechanical properties and microstructures were also analyzed in different high-frequency induction heating coil directions. The correlations between the high-frequency induction heating power and the distance from the specimen with the maximum tensile strength were determined.

Since the controllers of the variable speed seawater pump and the 3-way valve of a ship central cooling system receive the feedback signal from the same output, the two controllers may interfere and operate inefficiently under certain conditions. Therefore, studying an efficient control tuning method for the central cooling water system is necessary. The central cooling water system was modeled in this study using MATLAB Simulink, utilizing actual operation data, and unknown parameters are estimated to fine-tune. The model is then verified using another operating data set. Additionally, transfer functions are developed for freshwater output temperature against 3-way valve openness input and seawater pump motor electric power frequency input. Then, the two PI controllers are tuned through the Internal Model Control guide, supposing the two systems are decoupled. Moreover, the modified IMC tuning method is suggested for the seawater pump system, which has larger time constants because of a heat exchanger. This method simplifies combining the two PI controller tuning, enhancing the seawater pump's overall efficiency and 3-way valve operation. This study determined that the proposed tuning methods through the IMC guide confirmed the efficiency of controlling the seawater pump speed and 3-way valve with reasonable control of freshwater outlet temperature.

The Casimir–Lifshitz friction force and the heating rates of two metal plates with a narrow vacuum gap between them during nonrelativistic motion of one of them are calculated analytically and numerically within the framework of fluctuation electrodynamics. Changes in material properties are taken into account using the Bloch-Grüneisen and modified Bloch-Grüneisen (with finite residual resistance) resistivity models within the Drude approximation. It is shown that identical plates with the same initial temperature have the same heating rate, determined by the power of the friction force, and the possibility of measuring the friction force from the heating kinetics of nonmagnetic metal plates with temperatures of 1–10 K is substantiated.

This paper utilizes a life cycle assessment to evaluate the energy resources and environmental impacts of three heating systems. In the first step, life cycle assessments (LCAs) are prepared for the renewable, conventional, and combined systems. The system boundary of the LCA method is "cradle to gate," which means it includes the entire life cycle of a product or process. This includes energy supply, transport, energy generation, and operational energy use. The system scenarios were compared based on ecological and energy loads in the second step. Primary energy, resources, emissions, and environmental potentials are calculated for the system scenarios using the life cycle assessment methods CML 2016 and ReCiPe 2016. Finally, models for environmental reliability and complex decision-support tools have been developed. This work addresses two main questions: how to characterize the environmental and energy impacts of the systems under study, and what is the optimal scenario for the system? The research results show that the gas boiler system has a greater environmental impact. The most significant differences between the systems relate to the degrada-tion of abiotic fossil fuels when using a gas boiler and the process of acidification when using an electric heat pump. The results can be used to develop sustainable heating systems with reduced environmental impacts and enhanced energy efficiency.

Neutral beam injection (NBI) is used for thermonuclear plasma heating, non-inductive current drive, rotation, operation scenario control, and for plasma diagnostics in nuclear fusion devices. NBI is the main source of fast particles in plasma which transmit energy to thermal plasma during their slow-down. Steady-state tokamak operation is only possible when the sub-thermal particles energy is absorbed and effectively confined in plasma volume. While NBI purposes and applications vary through different fusion systems, the engineering tasks performed during research and development (R&D) stage of neutral beamline design have much in common. The NBI studies, especially addressing long pulse and high-power operation typically include a beam transmission analysis and power loads distribution at the structural components of the beamline. Thermo-structural analysis is applied next to heat removal circuits design. ‘Beam Transmission’ (BTR) code is a dedicated tool, developed by a physicist and used by NBI physicists and engineers. BTR was created and 1^st applied during R&D phase of the world’s largest tokamak ITER. BTR code is intended for public usage and routinely applied for detailed simulations of neutral beam propagation through complex beamlines. BTR is flexible and intuitive in input, user-friendly and fully interactive. Thanks to visualization and high performance BTR looks and feels like a real NB flight simulator. Despite BTR ‘mature’ age, the code is still in evolution. Support is available to all new BTR users.

Understanding the thermal cracks of rock caused by high temperature is of great help to the development of underground engineering, such as geothermal mining, underground coal gasification. Although there has been many study on thermal cracking, it is not systematic and in-depth enough. In order to deeply study the thermal crack mechanism of rock, this paper conducted thermal cracking experiments on granite at different temperatures and heating/cooling paths, and qualitative and quantitative analysis was conducted on the crack initiation characteristics, propagation paths, and crack network morphology of rock thermal crack under different test conditions. The thermal crack mechanism was also analyzed from the perspectives of mineral petrology, fracture mechanics, thermodynamics, and other aspects. The research results show that there are two obvious mutation points in the study temperature range for samples with fast cooling paths (SF path: slow heating and fast cooling; FF path: fast heating and fast cooling), around 200-300 ℃ and 600 ℃, respectively, while for samples with slow cooling paths (SS path: slow heating and slow cooling; FS path: fast heating and slow cooling), there is only one mutation point around 600 ℃. The initiation positions of thermal cracking under all temperature paths are relatively similar, with intergranular crack located between particles at the edge of the sample or intercrystalline crack in the middle of feldspar or quartz aggregates. The initiation temperature of SF and FF path specimens is relatively low compared to SS and FS path specimens, and the number and size of cracks is small. The crack network structure formed by the SF path is the most complex, with the largest crack ratio and cumulative crack length; The crack network structure formed by the FF path is relatively complex, with a larger main crack size but relatively fewer secondary cracks; The FS and SS paths do not form a complex network with good connectivity. The process of thermal crack development can be divided into three stages: the development of small cracks, the joint development of main cracks and small cracks, and the connection of cracks into a network structure. The mechanism of thermal crack propagation is that the expansion and thermal conductivity between different crystals are different. The thermal stress caused by temperature gradient and the tension or shear stress caused by the inconsistent deformation of crystals form stress concentration in weak areas such as particles boundary, cleavage, and original cracks. Firstly, it causes some crystals with smaller strength or less rounded shape to crack, and when the combined stress is large, the cracks will gradually expand along the existing fine cracks. This also explains that the most main cracks of the SF and FF path specimens mainly surround some large mineral aggregates or between particles.

Medium-deep Borehole Heat exchanger (MBHE) has been widely paid attention for building heating. In order to avoid the thermal interference of adjacent MBHEs, temperature distribution characteristics of medium-deep rock-soil was investigated in this work. The evolution on maximum rock-soil thermal affected radius (MTAR) in full life cycle was further analyzed. The results showed that the rock-soil thermal affected area (RTAA) continuously expands in both radial and vertical directions during a heating season. Several factors of thermal extraction load, fluid velocity, geothermal gradient and pipe length have main impacts on the RTAA in vertical direction. Rock-soil thermal conductivity affects the RTAA in both radial and vertical directions. In non-heating season, temperature difference of rock-soil in radial direction dominates the temperature recovery in the first year while geothermal flow nearly dominates temperature recovery after 20 years. The thermal affected radius (TAR) in the 30 th year could be determined as an effective MTAR in full life cycle. In order to decrease installed distance of adjacent MBHEs, a new well layout form by deflecting borehole was proposed. The recommended deflection angle is equal to or larger than 4 times TAR angle. This work provides scientific reference for promoting application of multiple MBHE arrays.

Heat using behavior has a large impact on in heating energy in heat metering system, and therefore a better understanding can assist in behavior guidance to reduce energy. To understand the current situation of indoor thermal environment and heat using behavior for heat metering households in northern China, including adjusting heating end valves and operating windows, 30 households were measured and surveyed. The factors influencing heat using behavior, including outdoor and indoor environmental parameters and time of the day, were analyzed. The results are :1) Thermal neutral temperature for heat metering households is relatively high, up to 24.5℃; 2) The heat using behavior of households is lack of rationality: low proportion of active households; high indoor temperature setting; more frequency of window opening. Improving indoor comfort is the main reason for households to adjust the heating end valve, and only 7.15% of households have considered the economic benefits brought by adjusting the valve. " Thermostat control valve does not work" is the main reason for households without adjustment; 3) Time of the day and indoor temperature affect active households’ willingness to adjusting heating end valve. Time of the day, indoor temperature and outdoor temperature have impacts on opening window during heating period.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

In this paper the application of the solid-state cooling based on barocaloric effect in the cold food supply chain is investigated. Barocaloric solid-state technology is applied to the final chain links of the cold food supply chain, regarding the steps of retail and domestic conservation. In this context a barocaloric cooler with regard to food needing to be kept at 5°C (273 K), in order to operate with a promising cooling technology that result energy efficient and environmentally friendly. The categories of food interested in the investigation are meets and fresh food products like soft cheese, yogurt, milk. The energy performances of the barocaloric system have been carried out and compared with a commercial vapor compression refrigerator of a similar size, both operating with R600a under the same working conditions. Basing on the following consideration one can conclude that barocaloric cooling is a favourable technology to be employed in the last link chains of the cold food supply chain if the system operates in ABR cycle at frequencies between 1.25 and 1.50 Hz with a regenerator made of acetoxy silicone rubber as solid-state refrigerant and 50%EG-50%water mixture as heat transfer fluid flowing at the optimal velocity of 0.15 m s-1 that guarantees an appropriate trade-off between the temperature span, the cooling power and the coefficient of performances. Under these conditions the barocaloric system overperforms the domestic vapor compression cooler operating with R600a.

Commercially available paraffin wax LTP ST, manufactured in Poland by POLWAX, was used as a phase change material (PCM) for passive cooling of a LED panel containing 28 high power light emitting diodes (LEDs). Paraffin wax LTP ST of density = 930 kgm-3 at room temperature (RT) was chosen over other POLWAX waxes (LUXOLINA, LUXOLINA-ST, LTP 56-20) because of its melting point range (44.5 – 55.4)℃, relatively high latent heat of fusion H = 218.8 Jg-1, high specific heat Cp = 2.11 Jg-1K-1 and thermal conductivity k=0.233 Wm-1K-1 at 0 ℃ [1]. The thermophysical properties were studied in samples of pure LTP ST paraffin and doped with multi-walled carbon nanotubes (1.99, 3.49, 5.35, 10.49 wt%, MWCNT) or silver nanowires (0.26, 0.32, 1.06, 2.10, 7.35 wt%, SNW). Analysis of the thermal effects of doped samples showed a relative increase in the degree of subcooling, averaging 100% for MWCNT and 46% for SNW , a relative 15÷25% decrease in enthalpy of melting for MWCNT and 14÷16% for SNW. A 44% increase in thermal conductivity was found for the sample containing 5.35 wt% MWCNTs and a 91% increase for 1.06 wt% SNW. The results of cooling efficiency tests for 3 types of developed heat sinks made of AW-2017A aluminum alloy are presented, i.e.: (a) - full system without PCM filling, (b) - system with PCM chamber without intracellular ribs, (c) system with PCM chamber with intracellular fins.

This paper Numerically investigates the effectiveness of the turbine rotating blade nozzle position on the vortex and film composite cooling performance. The coolant injecting nozzles arranged near the pressure surface side (PS-side-in) .vs. arranged near the suction surface side (SS-side-in) are compared at the rotating speed range of 0-4000rpm with fluid and thermal conjugate approach. Results show that the nozzle position presents different influences under low and higher rotating speed. In terms of the mainstream flow, rotation makes the stagnation line move from the PS-side pressure surface side to the SS-side suc-tion surface side, which changes the coolant film attachment on the blade leading edge surface. The nozzle position however indicates limited influence on the coolant film flow. In terms of the internal channel vortex flow, the coolant injecting from the nozzles forms a high-velocity region near the target wall which brings about enhancing convective heat transfer. The direction of the near wall vortex flow is opposite and align to the Coriolis force direction in both the PS-side-in and SS-side-in, respectively. Therefore, the Coriolis force augments to the heat transfer of the internal vortex cooling in SS-side-in while weakens the internal heat transfer in PS-side-in. Such effects become more intense with higher rotational speed. The blade surface area-averaged dimensionless temperature that inversely proportional to the actual temperature is 7.8% higher in SS-side-in as compared to that in PS-side-in. The SS-side-in suggests more superior composite cooling perfor-mance under the relatively higher rotating speed.

Solar heating technology is a promising solution to promote China to achieve the “3060 double carbon” target as soon as possible. And seasonal thermal storage (STS) can effectively solve the mismatch problem of solar heating systems between the supply and demand of thermal energy. Due to the instability of solar radiation resources and heat demand, it is necessary to analyze the dynamic response characteristics of the system. Yet, related studies are still scarce. In this study, a solar heating system with a solar tower receiver and STS was introduced in north China. The dynamic performance of the system is analyzed with a dynamic simulated method in a typical day or typical operation modes, and the switch mechanism between multiple operation modes is also revealed. The impact of different heating strategies on system performance was analyzed. Results showed that the solar fraction of the system reached 89.4% in the third year, which was 3.6% higher than the first year. The quality-quantity heating operation strategies can be effective ways to improve the discharge efficiency of STS and the system performance without any heat pump. The electricity consumption of the pump on the heating side could be significantly reduced by 44.6% compared with the quality control.

Based on the prosed criterion of the type of heating, a classification of the sources of pulsed electron beams was carried out, for better understanding both the nature of the thermal processes occurring under irradiation and for predicting their suitability for certain applications. The melting thresholds of materials were calculated over the wide ranges of accelerating voltages and pulse durations. On the basis of calculations, a refractoriness series of metals for surface-volume pulsed heating was proposed.

In this paper, the experimental study of heating in 2 h lunch mode of air-conditioned bed system is carried out. The results show that the power consumption of heat conduction heating is only 0.34 kW·h, and the average heat dissipation is 81.3 W, while the power consumption of convection heating is 1.43 kW·h, with an average heat dissipation of 748.7 W. Regardless of power consumption or heat dissipation, convection heating is significantly higher than heat conduction heating, resulting in the room air temperature of the former increased from 12.3 °C to 17.3 °C, while the latter only increased from 14.4 °C to 15.2 °C. The study found that the water temperature of heat conduction heating can meet the thermal comfort needs of the human body in the range of 38~40 °C, while convection heating requires a higher temperature range, In contrast, the grade of hot water required for heat conduction heating is lower. Through the experiment, it is also found that the temperature of convection heating rises fast, but it is easy to appear dry feeling after a long time, while heat conductive heating has a slow temperature rise. there is a cool feeling within 20 min after the heating starts, and then the thermal comfort is better. The air conditioning system in this paper is used for the heating experiment in the winter lunch break mode, compared with convection heating, the overall thermal comfort of heat conduction heating is better and more energy efficient. it is suggested to adopt heat conduction heating mode in the winter heating of this system.

Efficient natural convection-cooled heat sinks are vital to the future of electronics cooling due to their low energy demand in the absence of an external pumping agency in comparison to other cooling methods. The present study is aimed to identify the most effective fin design for enhancing heat transfer in natural convection applications. Initially, a baseline case with rectangular fins was considered in the present study and it was optimized with respect to fin spacing. This optimized baseline case is then validated against the semi-empirical correlation proposed by Elen-baas (1942) [2]. Upon good agreement, the validated model is used for comparative analysis of different heat sink configurations with rectangular, trapezoidal, curved, and angled fins. The optimised fin spacing obtained for the baseline case is also used for the other heat sink configura-tions and then the fin designs are further optimized for better performance. However, for the an-gled fin case, the optimized configuration proposed by Zhang et al. (2020) [3] is adopted in the present study. This study is carried out with Ansys Fluent for a Rayleigh number of 2.4 × 10^6. The proposed novel curved fin design with a shroud defined as Case C4 showed a 4.1% decrease in the system’s thermal resistance with an increase in the heat transfer coefficient of 4.4% when compared to the optimized baseline fin case. The obtained results are further non-dimensionalized with proposed scaling in terms of the baseline case for the two novel heat sink cases (trapezoidal, curved).

The study of energy sources has been an awareness of the modern world due to constraints on the current energy worldwide supply chain. The complexity of the theme as well as the consciousness of finite sources also the need of saving energy has become a priority. Although many papers have moved in this direction there is no record of papers studying the variables in a house heating system, which represents the highest energy consumption in many cold countries. This paper explores the energy-saving theme by studying the main variables present in houses’ heating systems in the winter season in cold countries like Canada, Russia, Norway, Iceland, Finland, etc. By using a novel combination of numerical thermal simulation by COMSOLTM and statistical analysis by MiniTabTM , it was possible to design an efficient thermal distribution in a house with the variables of the system by determining their significance and interaction qualitatively.

Salmorejo is a homogenate based on tomato, olive oil and breadcrumbs commercialized as a “fresh-like” cold puree in Spain and other European countries. Salmorejo is thermolabile and requires pasteurising upon High Temperature, Short Time (HTST) conditions to inhibit microbes and enzymes. Due to its penetration, dielectric heating by radiofrequency (RF) might improve pasteurisation results of conventional heating (CH) in viscous products. The objective was to validate the pasteurisation temperature (70-100 °C, at 5 ºC intervals) for salmorejo processed by radiofrequency (operating at 27.12 MHz for 9.08 s) or conventional continuous heating. Salmorejo was prone to thermal damage upon HTST conditions. Main heat-induced changes include: orangeness, flavour homogenisation, loss of freshness, thickening, loss of vitamin C and lipid oxidation. A ‘fresh-like’ good quality salmorejo can be obtained using either conventional or radiofrequency pasteurisers. Both CH and RF equivalent treatments allowed a strong reduction of total and sporulated mesophilic microorganisms, and an adequate inhibition of the pectinmethylesterase, peroxidase and, to a lesser extent, polyphenoloxidase, but did not inhibit the polygalacturonase enzyme. Pasteurisation at 80 °C for 9.8 s (RF) or 10.9 s (CH) provided a good equilibrium in levels of microbiological and enzymatic inhibition and thermal damage to the product. Increasing this temperature does not improve enzyme inactivation levels and salmorejo may become overheated.

In the present study a numerical bifurcation analysis of a thermistor problem is carried out, considering a realistic heat dissipation mechanism due to conduction, nonlinear temperature dependent natural convection and radiation. The electric conductivity is modeled as a strongly nonlinear and smooth function of the temperature between two limiting values, based on measurements. The problem formulated in this way admits multiple steady state solutions that do not depend on the external circuit. The analysis reveals that the conduction-convection parameter and the type of the boundary conditions have a profound effect on the solution structure and the temperature profiles. Depending on the boundary conditions the complex multiplicity pattern appears either as a series of nested cusp points or as enclosed branches emanating from pitchfork bifurcation points.

High in reliability, multi in function, strong in tracking and detecting, active phased array antennas have been widely applied in radar system. Heat dissipation is a major technological barrier preventing the realization of next-generation high-performance phased array antennas. As a result of the advancement of miniaturization and the in-tegration of microelectronics technology, the study and development of embedded di-rect cooling or heat dissipation has significantly enhanced the heat dissipation effect. In this paper, a novel swept-back fishnet embedded microchannel topology (SBFEMCT) is designed, and various microchannel models with different fishnet runner mesh den-sity ratios and different fishnet runner layers are established to characterize the chip Tmax, runner Pmax, and Tmax and analyze the thermal effect of SBFEMCT under these two operating conditions. The Pmax is reduced to 72.37% and 57.12% of the original at mesh density ratios of 0.5, 0.25, and 0.125, respectively. The maximum temperature reduction figures are average with little change in maximum velocity and a small increase in maximum pressure drop for the number of fishing mesh runner layers of 0-4. This paper provides a study of the latest embedded thermal dissipation from the dimension of a single chip to provide a certain degree of new ideas and ref-erences for solving the thermal technology bottleneck of next-generation high-performance phased array antennas.

A new longitudinal flow heat dissipation theory for cylindrical batteries is proposed in order to increase the energy density and uniform temperature performance of cylindrical lithium-ion battery packs while also shrinking their size by roughly 10%. First, a genetic algorithm is used to identify the single cell's thermal properties. Based on this, modeling and simulation are used to examine the thermal properties of the longitudinal flow-cooled battery pack. It is found that the best coolant flow scheme has one inlet and one outlet from the end face, taking into account the cooling effect of the battery pack and engineering viability. Lastly, Thermal Dummy Cells (TDC) is used to conduct a validation test of the liquid cooling strategy. Additionally, the simulation and test results demonstrated that the liquid cooling solution can keep the battery pack's maximum temperature rise under the static conditions of a continuous, high-current discharge at a rate of 3C to 20 °C and under the dynamic conditions of the New European Driving Cycle (NEDC) to 2 °C. In applications where the space requirements for the battery pack are quite severe, the longitudinal flow cooling method has some advantages.

In this article, an efficient die bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and the heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, FE-simulation methods were applied in order to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests in order to qualify the inductive bonding technology. The results presented in this paper demonstrate, that induction heating has high potential for cost effective production in the field of die-attach and can drastically increase the output in power electronics production.

Solar energy is a renewable and sustainable source of energy, and it has been used in addition of specified technologies, such as solar cooling. The demand for cooling continues to increase in line with environmental changes and a greater desire for human comfort. This study primarily aimed to analyze the performance of an evaporative cooling system powered by solar energy and assess the economic and environmental impact of this system. In this system, hot, dry incoming air is used to evaporate water, thus transforming part of its sensitive heat into latent heat without any variation in enthalpy or total heat. The outputted air then has a lower temperature and a greater humidity, thus providing a more comfortable, healthier environment for its users. To achieve this study’s objectives, numerical code was developed and implemented in MATLAB. The obtained results reveal that the efficiency of the evaporative cooler exceeds 90%, with maximum efficiency being reached at a high wet-bulb depression, while minimum efficiency was observed when the dry air has a high relative humidity and a low dry-bulb temperature.

Living walls (LWs) are a climate change adaptation strategy for cities, as they have a cooling effect. Previous studies of the cooling effect of LWs were carried out in different climatic zones. These studies differed in their experimental design, or simulated data via models. Plants’ cooling capacity is explained by shading and transpiration, and depends on physical plant parameters, environmental factors, and system-related influences. A three-year-long trial was carried out between 2017 and 2019 at an experimental garden in Geisenheim, Germany. We chose a textile-based LW system with high water demand and plants from a wet/fresh habitat. We assumed that this would achieve high evaporative cooling. The experimental setup included four experimental walls which were exposed to the north, south, east, and west, respectively. The plant choice was divided into three plant mix variants (Cascade, Ground cover, and Meadow) and a Control with no vegetation. We measured the temperature with sensors and a thermal imaging (IR) camera in different setups. The main results were that the measured vegetation temperature (TV) depends on air temperature (TA), measurement position, plant mix variant, and plant species. We could detect the cooling effect only at a small distance from the LW (microclimatic). Our methodological approaches should be continued in further studies.

In this study, the partial least squares regression (PLSR) models were developed using no pre-processing, traditional preprocessing, multi-preprocessing 5 range, multi-preprocessing 3 range, genetic algorithm (GA), and successive projection algorithm (SPA) to assess the higher heating value (HHV) and ultimate analysis of grounded biomass for energy usage employing near-infrared (NIR) spectroscopy. A novel approach was utilized based on the assumption that using multiple pretreatment methods across different sections in the entire NIR wavenumber range would enhance the performance of the model. The performance of the model obtained from 200 biomass samples for HHV and 120 samples for ultimate analysis was compared, and the best model was selected based on the coefficient of determination of validation set, root mean square error of prediction, and the ratio of prediction to deviation values. Based on model performance results, the proposed HHV model from GA-PLSR, and the N and O models from the mul-ti-preprocessing PLSR 5 range method could be used for most applications, including research, whereas the C and H models from GA-PLSR performance is fair and applicable only for rough screening. The overall findings highlight that the multi-preprocessing 5-range method, which was attempted as a novel approach in this study to develop the PLSR model, demonstrated better accuracy for HHV, C, N, and O, improving by 4.1839%, 8.1842%, 3.7587%, and 35.9404%, respec-tively. Therefore, it can be considered a reliable and non-destructive alternative method for rap-idly assessing biomass properties for energy usage and can also be used effectively in biomass trading. However, due to the smaller number of samples used in the model development, more samples are needed to update the model for a robust application.

Clinching is a manufacturing method of mechanical joining two or more materials without the use of heat or additional components. This process relies on high plastic deformation to create a secure bond. Clinching technology is widely used for joining various grades and thickness of materials. Especially in the automotive industry, clinching is an alternative to spot resistance welding. However, the load-bearing capacity of clinched joints is comparatively lower when compared to resistance spot welded joints. This research aimed to enhance the load-carrying capacity of clinched joints. Experimental tests were conducted on clinched joints with locally modified microstructures to optimize their placement within the joint. The microstructure distribution in the clinched joint region was analysed using light and scanning electron microscopy, as well as microhardness measurements. Two material grades, micro-alloyed steels HX420LAD+Z and dual-phase ferritic-martensitic steels HCT600X+Z, were tested. Each grade underwent five groups of ten samples, subject to identical experimental conditions of local heating by resistance spot welding (RSW) and clinching. The application of RSW to the clinched joint area resulted in increase of load-bearing capacity for both joined types of materials.

The microstructure and hardness along the thickness direction of a water quenched, high-strength thick plate with a thickness of 40 mm were investigated with three specimens from the thick plate: surface, 1/4t, and 1/2t (center) thickness, and the phase transformation behavior of the thick plate according to the cooling rate was analyzed through dilatometric experiments. Finally, the cooling rate for each thickness of the thick plate was estimated by comparing the microstructure and hardness of the thick plate along the thickness with those of the dilatometric specimens. Martensite microstructure was observed on the surface of the water quenched thick plate due to the fast cooling rate. On the other hand, an inhomogeneous microstructure was transformed inside the thick plate due to the relatively slow cooling rate and central segregation of Mn. A small fraction of bainite was shown at 1/4t thickness. A banded microstructure with martensite and bainite resulting from Mn segregation was developed at 1/2t; that is, the full martensite microstructure was transformed in the Mn-enriched area even at a slow cooling rate due to high hardenability, but a bainite microstructure was formed in the Mn-depleted area owing to relatively low hardenability. A portion of martensite with fine cementite at the surface and 1/4t was identified as auto-tempered martensite with a Bagaryatskii orientation relationship between the ferrite matrix and cementite. The microstructure and hardness as well as dilatation were investigated at various cooling rates through a dilatometric experiment, and a continuous cooling transformation (CCT) diagram was finally presented for the thick plate. Comparing the microstructure and hardness at the surface, 1/4t, and 1/2t of the thick plate with those of dilatometric specimens cooled at various cooling rates, it was estimated that the surface of the thick plate was cooled at more than 20 oC/s, whereas the 1/4t region was cooled at approximately 5 ~ 10 oC/s during water quenching.

Phase change materials (PCMs) have emerged as promising solutions for latent heat thermal energy storage (LHTES) systems, offering considerable potential for storing energy derived from renewable sources across various engineering applications. The present study focused on optimization of solar cooling system by integrating LHTES with different PCM tank configuration. TRNSYS simulation software was selected for the study and collected experimental data from laboratory system prototype was used for system validation. The results indicate that the use of PCM led to a noteworthy decrease of 6.2% in auxiliary energy consumption. Furthermore, the duration during which the heat carrier temperature flow exceeded 90°C from the storage tank to the auxiliary heater was extended by 27.8% when PCM was utilized, compared to its absence. The use of PCM in LHTES is more effective under variable weather conditions. On the day when changes in weather conditions were observed, around 98% of the cooling load was provided by produced sun energy. The results of the research can be used to optimize the solar cooling system, which will help reduce the environmental impact of cooling systems running on non-renewable fuels.

For the agricultural sector to develop sustainably in the future, progress toward more environmentally friendly technologies and methods is crucial. It is necessary to increase output while reducing the demand for energy, agrochemicals, and water resources. Although greenhouses can be utilized successfully for this purpose, significant technical advancements are required, especially when it comes to heating, to lower the use of fossil fuels and boost energy efficiency. Infrared waves and microwaves, for instance, can warm plants without having to heat the entire greenhouse volume, which takes a significant amount of energy to compensate for heat loss to the outdoor environment. In this paper, through a thorough examination of the state of the art, a general overview of novel greenhouse heating systems based on radiation is reported. First, infrared heating of greenhouses is analyzed, then the strengths and weaknesses of microwave and dielectric heating are discussed, and finally the use of microwaves for soil sterilization is examined. All outcomes suggest these irradiation-based technologies can contribute significantly to an agriculture that is energetically sustainable.

Liability to prevent consequences of an unhealthy situation due to accumulating toxic and hazardous emissions caused by open dumping of municipal solid waste with increasing urbanization has necessitated a renewed thinking on waste disposal. Grate fired incineration systems were adopted by urban managements in past and present but with criticisms due to formation of air borne emissions. Improved combustion methods like fluidized bed are now propagated because of current requirements like efficient energy recovery potential, stricter emission norms, adaptability with urban growth, adaptability to co-firing with other waste like biomass, edible oil wastes or industrial effluent and integration with conventional energy generation. Such a comprehensive and futuristic approach is more sustainable for the community. Multi-criteria decision-making tool is used to identify the best technology option among grate combustion and fluidized bed combustion for disposing and energy recovery from waste. Ten different collection and disposal options involving two combustion methods, namely, grate combustion and fluidized bed method are considered. Utilization of the energy is done for three end uses, namely, power generation, water distillation and district cooling. Two different regions in Saudi Arabia are considered for this study under two types of scenario, namely with recycling and without recycling. The different options are prioritized based on their overall ranking using five major performance factors.

Ground-based high-power lasers enable to, in principle, deorbit any kind of space debris object from the low Earth orbit (LEO) by remotely inducing laser-ablative momentum. However, the assessment of efficiency and operational safety depends on many factors like atmospheric constraints or the risk of debris disintegration during irradiation. We analyze laser momentum for a great variety of target geometries and sizes, and – for the first time in a large-scale simulation – include thermal constraints for laser irradiation configuration. Using a coherently coupled 100 kJ laser system at 1030 nm wavelength, 5 ns pulse duration in an optimized pointing elevation angle range, the pulse frequency should amount to less than 10 Hz to prevent fragment meltdown. For mechanically intact payloads or rocket bodies, repetition rates should be even lower. Small debris fragments sized between 10 and 40 cm can be de-orbited by around 100 to 400 station passes with head-on irradiation while objects exceeding 2 m typically require far more than 1000 irradiations for deorbit. Hence, laser-based debris removal cannot be considered a prime space sustainability measure tackling the top-risk large debris, yet it can provide for remediation of a multitude of small-sized debris using small networks of globally distributed laser sites.

Currently, the district heating (DH) in Poland is facing many challenges. The business model used hitherto was very simple—in most cities, heating plants produced heat, and centralized heating systems supplied the "product" at a price approved annually by the president of the Energy Regulatory Office (URE). However, recent years have brought significant changes on the market. EU regulations force the elimination of old coal-fired plants that were still built in the Polish People's Republic (PRL), moreover, high prices of CO2 emission allowances aggravate the financial situation of companies. In addition, in the heating sector, the trend observed in the power sector is becoming increasingly visible—limiting the role of large sources in favor of energy generated locally, closer to the customer. One of the biggest challenges is achieving the targets set by the EU for the share of renewable energy sources (RES) in the heating sector. The war in Ukraine and problems with the supply of coal and gas are an additional impulse to turn to RES. Thus, the development of sustainable and innovative solutions for energy production and supply at the level of urban networks is currently one of the main technical challenges. The purpose of the paper is to present the current situation and perspectives of development of district heating systems in Poland with a view to the status of district heating in the world, and some deeper insight into European conditions. The review presents energy sources with particular emphasis on renewable energy sources (RES) and their cogeneration for heat production. The examples of existing heating network solutions using renewable energy sources, based on the selected published case studies, are also discussed.

This study investigates the efficiency of a biogas-powered cooling system through the utilization of energy and exergy calculations. Biogas, which can be generated and stored in small-scale plants as needed, serves as a viable fuel source for absorption cooling systems. The present research focuses on the biogas consumption of a triple-effect absorption cooling system, specifically designed to supply a fixed cooling load of 100 kW under varying operational conditions. The study highlights the COP (Coefficient of Performance) and ECOP (Exergetic Coefficient of Performance) values of the system, along with the exergy destruction rates of its individual components, at the optimal temperatures of operation. Furthermore, to determine the necessary biogas consumption, the study explores the establishment of dedicated farms for various animal species, ensuring an adequate number of animals for biogas production. The findings reveal a COP of 1.78 and an ECOP of 35.4% at the optimized operating temperatures. The minimum mass flow rate of biogas is determined to be 0.0034 kg/s, facilitating the operation of the boiler with a methane content of 65%. The study concludes that a total of 290 head of cattle is required to generate the annual biogas consumption necessary for the cooling system. Also, number of the cattle is enough to establish 284 biogas plants in Bursa province in Türkiye.

A variety of factors ranging from ethnicity and occupants’ lifestyles to local climatic characteristics of any studied location and people’s age factors can affect thermal comfort assessment globally. Due to the detrimental impact of climate change, the building industry has started to implement energy efficiency schemes while considering the thermal comfort of vulnerable population both for the society and any sphere of economy. Although, considering human-based approaches have been neglected by other scholars in thermal comfort studies. This paper reviews energy effectiveness of state-of-the-art passive systems in providing neutral adaptive thermal comfort for elderly people, through exploring passive design strategies in four distinct climates namely, Canada, India, Abu Dhabi and the South-eastern Mediterranean basin. The aim of the study is to analyze the available data provided by the ASHRAE Global Thermal Comfort Database II version record 2.1. The main objective of the study is to develop an effective methodological framework for the on-going development of adaptive thermal comfort theory. To this extend, this study presents a comprehensive review on the assessment of energy effectiveness of passive design systems. To accomplish this, the impact of climate change factor in passive design systems was investigated. The meta-analysis method was adopted to determine the input variables for the statistical analysis. Cramer’s V and Fisher’s Exact tests were used to assess occupants’ thermal sensation votes (TSVs). The findings revealed that there are discrepancies detected between the in-situ field experiments and the data recorded in the ASHRAE Global Thermal Comfort Database II. According to the Köppen-Geiger climate classification, it was found from the study that the slightly high temperature fluctuations were identified in India where the weather is dry and savanna climate. The study findings contribute to the development of adaptive thermal comfort theory by reviewing the existing methodologies globally. Furthermore, a critical review on the significance of occupants’ age differences should be conducted in the identification of neutral adaptive thermal comfort.

To achieve the required mechanical properties in the heat treatment of steel, it is necessary to have an adequate cooling rate and to achieve the desired final temperature of the product. This should be achieved with one cooling unit for different product sizes. In order to provide high variability of the cooling system, different types of nozzles are used in modern cooling systems. Designers often use simplified, inaccurate correlations to predict the heat transfer coefficient, resulting in oversizing of the designed cooling or failure to provide the required cooling regime. This typically results in longer commissioning times and higher manufacturing costs of the new cooling system. Accurate information about the required cooling regime and the heat transfer coefficient of the designed cooling is critical. This paper presents a design approach based on laboratory measurements. Firstly, the way to find or validate the required cooling regime is presented. The paper then focuses on nozzle selection and presents laboratory measurements that provide accurate heat transfer coefficients as a function of position and surface temperature for different cooling configurations. Numerical simulations using the measured heat transfer coefficients allow the optimum design to be found for different product sizes.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.

This study utilized electron back scattered diffraction (EBSD) and X-ray diffraction (XRD) to investigate the impact of inter-annealing temperature and heating rate of final annealing on the microstructure of high-voltage anode aluminum foils. The findings indicate that the formation of cube texture in the final products is significantly influenced by the inter-annealing temperature, as low inter-annealing temperatures retain a considerable amount of deformation stored energy, providing a strong driving force for nucleation. The cube texture is observed to deviate from the ideal position at lower inter-annealing temperatures. Additionally, an increase in heating rate during final annealing leads to a gradual decrease in the fraction and grain size of recrystallization. This is attributed to the fact that a higher heating rate (below the critical heating rate) reduces the time available for grain boundary migration, thereby slowing the recrystallization process.

The manuscript presents a unified methodology for the engineering design of resonant inverters used for power sources to power various technologies based on induction heating. The methodology is compiled using the generalized consideration of electromagnetic processes in a series RLC circuit and the quasi-boundary method for the analysis of resonant inverters with and without reverse diodes operating in soft and hard commutation modes. On this basis, the transmission functions of the inverters are derived, and the matching between the parameters of the inverter and the load through complicated output circuits is also considered. The basic ratios for determining the circuit elements and their current and voltage loading are presented. The methodologies are verified using several computational examples, simulations and measurements from induction heating devices. The simplified design approach presented is useful for its application in power electronics training and also in the design of various devices using the principle of induction heating. Another important result is the achievement of formalization and algorithmization of the design process, which is a consequence of the application of a unified approach both in the analysis and in the design of a whole class of power electronic devices.

Abstract— In this paper, degradation effects such as the self-heating effect and the DIBL effect in 2D-MoS2-based MOSFETs are investigated through simulations. These are transistors with Al2O3 and HfO2 as the gate oxide and SiO2 and HfO2 as the back oxide (BOX). The self-heating effect (SHE) is simulated using the thermodynamic transport model. The dependence of the DIBL effect (Drain Induced Barrier Lowering) and the lattice temperature in the center of the channel on the gate length for transistors with different gate oxide and BOX materials is considered. Transistors are considered where the channel is fully and partially (just below the gate) covered by gate oxide. It is shown that the transistors with Al2O3 as gate oxide and SiO2 as BOX materials have higher immunity to DIBL effect and transistors with HfO2 as gate oxide and HfO2 as BOX materials have higher immunity to SHE.

Zeolitic imidazolate frameworks (ZIFs) have potential for various gas and ion separations due to their well-defined pore structure and relatively easy fabrication process compared to other metal-organic frameworks. As a result, many reports have focused on preparing polycrystalline and continuous ZIF layers on porous supports. In this study, we investigated how humidity and chamber temperature influence the structure of a ZIF-8 layer prepared by the hydrothermal method. We controlled the chamber temperature (ranging from 50 °C to 70 °C) and relative humidity (ranging from 20 % to 100 %) using a thermos-hygrostat chamber. We found that as the chamber temperature increased, ZIF-8 preferentially grew into particles rather than forming a continuous polycrystalline layer. By measuring the temperature of the reacting solution based on chamber humidity, we discovered that the heating rate of the reacting solution varied with humidity, even at the same chamber temperature. At higher humidity, thermal energy transfer was accelerated as water vapor delivered more energy to the reacting solution. Therefore, a continuous ZIF-8 layer could be formed more easily at low humidity ranges (ranging from 20 % to 40 %), while micron ZIF-8 particles were synthesized at a high heating rate. Our findings suggest that controlling the heating rate of the reacting solution is critical to preparing a continuous ZIF-8 layer, particularly for future scale-up of ZIF-8 membranes.

Engine Overheating is a condition where the engine temperature has increased above the working temperature. This analysis aims to analyze the damage, determine the factors causing the damage, identify corrective steps and prevent engine overheating. The inspection procedure is carried out by checking the cooling system's components, cylinder head, and cylinder block. Further analysis using a fishbone diagram to analyze the causes of engine overheating troubleshooting. Damage analysis results Engine overheating occurs because the thermostat is damaged, namely, the thermostat valve which cannot open when the temperature reaches the standard temperature (71oC), and also due to damage to the cylinder gasket which causes bubbles due to compression leaks and mixing of radiator coolant and oil. Repair steps are taken in the form of replacing damaged components with new ones. Preventive measures are taken by not using the unit on an over-running basis, checking coolant levels, carrying out daily checks properly and correctly, and carrying out preventive maintenance regularly.

The results of the study of the influence of the size of cylindrical samples of A5N aluminum on the time and rate of their cooling are presented. According to experimental data, the temperature dependence of the heat transfer coefficient for pure metals is calculated. It revealed that the process of cooling of the aluminium and its alloys has a relaxation behavior. It has found that the main mechanisms of natural air cooling are convection heat transfer and radiation. The characteristic cooling time due to radiation is less than due to convection. The contribution of thermal radiation is noticeable at high temperatures. It was found that the characteristic times of cooling due to radiation and convection increase with increase in volume to area ratio of the sample.

Emissions from wood burning for heating in secondary homes or cabins is an important aspect for the development of high-resolution emission inventories in specific areas. Norway is used as case study as the national wood consumption for heating in cabins is around 20% of the total. Our study shows first a method to estimate emissions from cabins based on traffic data to derive cabin occupancy, which combined with heating need allows for the spatial and temporal distribution of emissions. The combination of residential (RWC) and cabin wood combustion (CWC) emissions shows large spatial and temporal differences, and a temporally “cabin population” can in areas be orders of magnitude larger than the registered population. While RWC emissions have been steadily reduced, CWC have kept relatively constant or even increased, which results on an increase in the cabin share to total heating emissions up to 25-35%. When comparing with regional emissions inventories, our study shows that the gradient between rural and urban areas is not well represented in regional emissions inventories, which resembles a population-based distribution and does not allocate emissions in cabin municipalities. At last, our study shows that CWC emissions may become an increasing environmental concern as higher densification trends in mountain areas are observed.

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

This paper focuses on the comparative analysis of lithium-ion batteries (LIB) thermal management with aim to maintain working temperature in the range 15 ℃ – 35 ℃. This is to prevent thermal runaway and high temperature gradients. The proposed approach is to employ the biodiesel, situated inside the diesel/LIB powered hybrid electric vehicle, to supply as fuel and coolant. A 3S2P LIB module is simulated using Ansys-Fluent CFD software tool. The system without a coolant shows that LIB has exceeded the optimum maximum temperature, which leads to shortened life-cycle and poor performance. Four fatty acid methyl ester biodiesels are used as coolants, namely palm, karanja, jatropha, and mahua oils. When compared with conventional methods of cooling, using air and 3M Novec liquid, the palm biodiesel coolant proves to be the best option to maintain LIB temperature within the optimum working range. With the use of palm biodiesel, the system is estimated to lightweight the BTMS by 43%, compared to the case when 3M Novec is used to maintain the same temperature range.

Briquetting of biomass is an ideal technique for improvising both its volumetric and net energy density; besides, serving as an effective means for reducing pollution. In general, numerous biomass and organic by-products are discarded as wastes, citing their non-edibility, composition of chemical compounds present in their raw form, in addition to their zero usage value. Yet, these biomass wastes hold significant heating values, which promote them into promising solid biofuels, either in their existing or pre-treated form. Accordingly, this review article discusses about the various biomasses used as raw feedstock for briquetting, besides summarising the works carried out in relevance to their respective briquettes. In addition, proximate and lignocellulosic composition of these biomasses, and their pre-treatment techniques followed to prepare them for briquetting, have also been discussed. This study suggested that the heating value of biomasses ranged between 10-20 MJ/kg, whilst, their briquettes reported between 15 and 25 MJ/kg; thereby citing their potential as viable replacement for existing fossil coals. Besides, factors affecting different thermal and physicochemical properties of these briquettes have also been studied and concluded that these properties play a crucial role in deciding the overall quality of the briquettes. Ultimately, this study proposed that any biomass with good calorific value and lignin content can be processed into briquettes with good strength and durability; however, the choice of biomass will also be accounted for by its availability, geographical distribution, and handleability.

To verify the authors’ mathematical model for water jet cooling of steel sheet, the previously performed experimental studies of temperature of the test plate in the roller quenching machine (RQM) were used. The calculated data of steel temperature evolution along the RQM length were compared with the readings of thermocouples inserted in the center of the test plate and at its surfaces. The core of the model is the dependence of the temperatures of film, transition and nucleate boiling regimes on the thickness of the oxide scale layer on the cooled surface. It was found that the model correctly takes into account the oxide scale on the sheet surface, flow rates and combinations of the RQM banks used, water temperature and other factors. For all experiments the calculated metal temperature corresponds well to the measured one. In the experiments with interrupted cooling, the calculated temperature plots repeat the characteristic changes in the experimental curves. The main uncertainty in the modeling of cooling in a wide temperature range can be contributed by the random nature of changes in the oxide scale thickness during water cooling. In this regard, the estimated thickness of the oxide scale layer should be considered as the main parameter for adapting the sheet temperature control process. The obtained data confirm the possibility of effective application of the model in the ACS of industrial TMCP (Thermo-Mechanical Controlled Process) systems.

This paper proposes and demonstrates, in full scale, a novel type of energy geostructure (“the Climate Road”) that combines a ground source heat pump (GSHP) with a sustainable urban drainage system (SUDS) by utilizing the gravel roadbed simultaneously as energy source and rainwater retarding basin. The Climate Road measures 50m x 8m x 1m (length, width, depth) and has 800 m of geothermal piping embedded in the roadbed, serving as the heat collector for a GSHP that supplies a nearby kindergarten with domestic hot water and space heating. Model analysis of operational data from 2018-2021 indicates sustainable annual heat production levels around 0.6 MWh per meter road, with a COP of 2.9-3.1. The continued infiltration of rainwater to the roadbed increases the amount of extractable heat by an estimated 17% compared to the case of zero infiltration. Using the developed model for scenario analysis we find that draining rainwater from three single family houses and storing 30% of the annual heating consumption in the roadbed, increases the predicted extractable energy by 56% compared to zero infiltration with no seasonal energy storage. The Climate Road is capable of supplying three single family houses with heating, cooling and rainwater management year-round.

Nowadays, energy saving is considered a key issue worldwide, as it brings a variety of benefits: reducing greenhouse gas emissions, reducing demand for energy imports, and lowering costs on a household and economy-wide level. Researchers and building designers are looking to optimize building efficiency by means of new energy technologies. Changes in existing buildings can also be made to reduce energy consumption and costs. These may include the usage of new heat transfer fluids based on nanofluids. In this work, an extended experimental campaign (from February 2020 to March 2021) has been carried out on an educational building in the Campus of University of Salento, Lecce – Italy, in order to evaluate the increase in performance of the HVAC system, due to the usage of a nanofluid. The results show that, under optimal operating conditions, plant performance improves more than 10%, with average daily peaks of about 15%.