At room temperature, the indentation morphologies of crystalline copper with different grain size including nanocrystalline (NC), ultrafine-grained (UFG) and coarse-grained (CG) copper were studied by nanoindentation at the strain rate of 0.04/s without holding time at indentation depth of 2000 nm. As the grain size increasing, the height of the pile-up around the residual indentation increases and then has a slightly decrease in the CG Cu, While the area of the pile-up increases constantly. Our analysis has revealed that the dislocation motion and GB activities in the NC Cu, some cross- and multiple-slips dislocation insides the larger grain in the UFG Cu, and forest dislocations from the intragranular Frank-Read sources in the CG Cu, would directly induce these distinct pile-up effect.

Nanopeening treatment was applied to the AISI 420 steel to decrease its sensitivity to the tribocorrosion damage. Microstructural investigation highlighted that the Nanopeening treatment led to a high plastic deformation and nanostructured surface layer with 110 µm depth. . In order to study the combined effect of corrosion and mechanical wear, tribocorrosion tests were performed on non–treated and nanopeened samples in boric acid and lithium hydroxide solution, considering both continuous and intermittent sliding. It was found that the AISI 420 steel is sensitive the synergism between mechanical friction and electrochemical corrosion with a domination of abrasive wear. Adhesive wear was also detected in the wear track. Indeed, the mechanical wear was pronounced under intermittent sliding because of hard wear debris generation from the repassivated layer during rotating time. The Nanopeening treatment led to enhance mechanical performance and corrosion properties. Such improvement could be explained by the high plastic deformation resulting in the nano-structuration of grains and increasing hardness of AISI 420 steel.

This review focuses on developments that quantify grain quality with a range of spectral sensors in an on-farm setting. If the application of sensor technologies were expanded and adopted on-farm, growers could identify the impact and manage the harvesting operation to meet a range of quality targets and provide an economic advantage to the farming enterprise.

The bimodal grain-size distribution 0.9KNbO₃-0.1BaTiO₃ ceramics, with a typical perovskite structure in tetragonal phase at room temperature, were successfully prepared by an induced abnormal grain growth (IAGG) method at a relatively low sintering temperature. In this bimodal grain-sized distribution structure, the extra-large grains (about 10‒50 μm) were evolved from the micron-sized filler powders and the fine grains (about 0.05‒0.35 μm) were derived from the sol precursor matrix. The 0.9KNbO₃-0.1BaTiO₃ ceramics exhibit relaxor-like behavior with the diffused phase transition near room temperature, and confirmed by the existence of the polar nanodomain regions (PNRs) using the HRTEM images. The large room-temperature electrocaloric (EC) effect was found, characterized by an adiabatic temperature drop of 1.5 K, an isothermal entropy change of 2.48 J kg^-1 K^-1, and high EC strengths of ïDT/DEï = 1.50×10^-6 KmV^-1 and DS/DE = 2.48×10^-6 Jmkg^-1K^-1V^-1directly measured under E = 1.0 MV/m. These excellent ECEs demonstrate that this simple IAGG method is highly appreciated for synthesizing high-performance EC materials for efficient cooling devices.

Overexpression of a constitutively active truncated form of OsCDPK1 (OEtr) in rice produced smaller seeds, but a double-stranded RNA gene-silenced form of OsCDPK1 (Ri) yielded large seeds, suggesting that OsCDPK1 plays a functional role in rice seed development. In the study presented here, we propose a model in which OsCDPK1 plays key roles in negatively controlling the grain size, amylose content, and endosperm appearance, and also affects the physicochemical properties of the starch. The dehulled transgenic OEtr grains were smaller than the dehulled wild-type grains, and the OEtr endosperm was opaque and had a low amylose content and numerous small loosely packed polyhedral starch granules. However, the OEtr grain sizes and endosperm appearances were not affected by the temperature being either optimal (25 °C ) or low (22 °C) or high (31 °C) during the grain-filling phase. In contrast, the transgenic Ri grains were larger, had higher amylose contents, and had more transparent endosperms filled with tightly packed polyhedral starch granules. This demonstrates that OsCDPK1 plays a novel functional role in starch biosynthesis during seed development and affects the transparent appearance of the endosperm. These results improve our understanding of the molecular mechanisms through which the grain filling process occurs in rice.

The quantitative and qualitative assessment of gold grains from samples of glacial till is a well-established method for exploring gold deposits hidden under glaciated cover. This method, widely used by the industry and which produced numerous successes in locating gold deposits in glaciated terrain, is still based on artisanal gravity separation techniques and visual identification. However, being artisanal, it is limited by inconsistent recoveries and the difficulty to visually identify the predominantly occurring small gold grains. These limitations hinder its capability to deceipher subtle or complex signal. To improve detection limits through recovery of small gold grains, a new approach has recently been introduced in the industry (commercially referred as “ARTGold” procedure) using an optimized miniature sluice box coupled with an automated scanning electron microscopy routine. The capabilities of this improved method are highlighted by comparing till surveys conducted around the Borden gold deposit (Ontario, Canada) using the conventional and improved methods at both local and regional scales. Relative to the conventional approach, the improved method recovered almost one order of magnitude more gold grains from samples (regional and down-ice mineralization), dominantly in small size fractions. Increasing the counts in low-abundance regional samples enables better discrimination between background signals and significant dispersions. The method offers an alternative to improve characterization of gold dispersal in glaciated terrain and the related gold deposit footprints.

ABSTRACT: Waterlogging is a common abiotic stress in global maize production. Maize flowering stage (from tasseling to silking) is more fragile to environmental stresses among different growth stages. The effects of waterlogging at flowering stage on the grain yield and starch quality of waxy maize were studied using Suyunuo5 (SYN5) and Yunuo7 (YN7). The grain yield and starch concentration of both hybrids were reduced by waterlogging. The size of starch granules and proportion of small-molecule amylopectin increased in SYN5 and decreased in YN7 when plants suffered waterlogging at flowering, in contrast to the change trend of relative crystallinity. The pasting viscosities and gelatinization temperatures were reduced, whereas the gelatinization enthalpy was unaffected by waterlogging in both hybrids. Our study indicated that waterlogging at flowering reduced the grain yield, restricted starch deposition, and deteriorated the pasting property of waxy maize. Between the two hybrids, YN7 and high pasting viscosities and low retrogradation percentage than SYN5, indicated its advantages on produce starch for viscous and less retrograde food. Results provide information for utilization of waxy maize grain in food production.

Landslides are serious geological hazards that become a disaster worldwide, causing a large number of casualties and economic losses every year. There are many factors affecting landslide susceptibility, such as rainfall, soil and slope. Each of them has an important role in the process of slope losing stability. In this paper, the effects of rainfall intensity, rainfall pattern, slope gradient and soil type on landslide susceptibility are studied. In the process of rainfall-induced landslide, the relevant physical quantities of soil changes continuously. Their values and processes are closely related to the time of landslide occurrence. Hence, the variation of soil volumetric water content, matrix suction, pore water pressure and total stress throughout the rainfall are measured. As the results, soil type, slope gradient and rainfall intensity have a large influence on landslide susceptibility. The occurrence of landslides has a prerequisite that the slope is greater than or equal to 15°. The rainfall intensity needs to be not less than 80 mm/h. The difference of rainfall pattern also affects the landslide susceptibility. The rainfall pattern with rainfall intensity peak at the later stage is more likely to induce landslide. Coarser soils with gravels are prone to landslides when other conditions are the same. Steeper slopes, stronger rainfall, and coarser soils can all increase the amount of sediment yield.

This study aims to explore the differences between loess and landslide deposits, focusing on as-pects such as particle distribution, consolidation characteristics, and dynamic shear modulus. Through a series of experiments, the research reveals the similarities and differences between these two entities, yielding several key findings. Firstly, the process of landsliding disrupts the original structure of the loess, resulting in a reduction in porosity and a densification of the soil. This alteration in structural properties leads to significant disparities in physical attributes be-tween landslide deposits and undisturbed loess. Additionally, the movement and sorting of par-ticles during landslides cause variations in particle size distribution across different sections of the landslide deposits. Secondly, the landslide process not only alters the soil's structure but also changes the particle sizes within the loess. Particle wear and sieving result in the transformation of larger particles into smaller ones, leading to a more uniform particle size distribution. This shift in structure and particle size directly impacts the consolidation characteristics of landslide deposits, resulting in a substantial reduction in compression coefficient. Despite undergoing consolidation for decades, the middle and lower sections of landslide deposits still exhibit un-der-consolidation. Although the differences in the maximum dynamic shear modulus between loess and landslide deposits at varying depths are relatively minor, differences in porosity and consolidation characteristics lead to faster decay rates of the dynamic shear modulus for the lat-ter. The study also highlights a reduction in the water sensitivity of the maximum dynamic shear modulus within landslide deposits. Based on experimental results, a predictive model is pro-posed, utilizing A and m values to estimate the maximum dynamic shear modulus of both loess and landslide deposits. In conclusion, this research uncovers the impact of landslide processes on the structure and properties of loess, providing insightful understanding into the disparities between these two entities.

The paper presents the first retrievals of clean snow properties using spaceborne hyperspectral The Environmental Mapping and Analysis Program (EnMAP) observations. The location close to the Dome C in Antarctica has been selected. At this location the atmospheric effects except molecular light scattering and absorption are weak and the simplified atmospheric correction scheme can be applied. The ice grain size, snow specific surface area and snow spectral and broadband albedos have been retrieved using single view EnMAP measurements. In addition, we propose the technique to retrieve trace gas concentrations (e.g., water vapor, ozone) from EnMAP observations over the snow surfaces. Close correspondence of satellite and ground measured parameters has been found.

Raindrop size distribution (RSD) is an index for reflecting precipitation characteristics. Analyzing the differences of RSD plays an important role in understanding the precipitation microphysical processes and improving quantitative precipitation prediction of radar. In this paper, the RSD data of Dafang (57708) station, Majang (57828) station, and Luodian (57916) station (with an altitude of 1722.7m, 985.0m, and 441.5m, respectively) in Guizhou are analyzed according to the precipitation microphysical characteristics. First,Particles with particle size less than 1mm contributes the highest value to the density of particle number , and decrease with the descending altitude. Second, the GAMMA distribution fit shows a better fit compare to M-P distribution fit, and GAMMA distribution fit increases with the ascending altitude. Third, the mass-weighted average diameter is not sensitive enough to the change of precipitation intensity with correlation coefficients of 54.84%, but there is a obvious relationship between the average volume diameter and the precipitation intensity with correlation coefficients of 69.15%. Then, the precipitation prediction model is established using LSTM neural network after fusing the representative microphysical characteristics of RSD with radar and rain gauge data. The precipitation prediction model is applied to the Dafang (57708) site to predict precipitation for time range of 0-180 minutes, and it is found that for the prediction of convective cloud and stratiform cloud precipitation, the 60-minute prediction results are the most consistent with the actual precipitation, where the correlation coefficients are 92.87% and 92.57%, respectively. Conclusively, the results demonstrate that combining with the RSD base data could improve the reliability of precipitation forecasting.

The information entropy for Smoluchowski coagulation equation is proposed based on statistical mechanics. And the normalized particle size distribution is a lognormal function at equilibrium from the principle of maximum entropy and moment constraint. The geometric mean volume and standard deviation in the distribution function are determined as simple constant. The results reveal that the assumption that algebraic mean volume be unit in self-preserving hypothesis is reasonable in some sense. Based on the present definition of information entropy, the Cercignani’s conjecture holds naturally for Smoluchowski coagulation equation. Together with the proof that the conjecture is also true for Boltzmann equation, Cercignani’s conjecture will holds for any two-body collision systems, which will benefit the understanding of Brownian motion and molecule kinematic theory, such as the stability of the dissipative system, and the mathematical theory of convergence to thermodynamic equilibrium.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

The interactions of metal ions with fulvic acids resulted in changes in the particle size and charge. Particle size distribution was trimodal for fulvic acids, bimodal for fulvic complexes with calcium and magnesium, and copper-fulvic complexes had only one size fraction. The compensation of negative charge of carboxylic and phenolic functional groups by positive charged metal ions resulted in the increase in zeta potential which was getting closer to zero in the case of copper-fulvic complexes. However, all metal humic complexes behaved as colloidally unstable which resulted in visually observable sedimentation. Calorimetric measurements provided positive values of changes in enthalpy which indicated endothermic processes. In contrast quantum chemical calculations as well as experiments with model compounds provided negative values indicated exothermic processes. Changes in Gibbs energy were determined as negative and changes in entropy as positive which meant spontaneous processes.

In this paper, the effects on the rheological properties, particle size distribution, and fluorescence properties of red wine were investigated under microwave irradiation, and the mechanism of the effects of microwave irradiation on the sensory properties of red wine was discussed. The results showed that the effect of microwave on the rheological properties in red wine could be fitted by the Power-law model and Carson model, through the analysis of the rheological constants, yield stress, and viscosity coefficient of wine, it was found that microwave treatment could improve leg phenomenon and thickening effect by the change of rheological properties; the particle size distribution in wine indicated that microwave irradiation did change the particle size distribution through friction effect and oxidative polymerization, resulting in the wine’s visual effect and mouthfeel; the wine quality could be improved by enhancing the fluorescence intensity under different microwave conditions, which meant that microwave technology could speed up the formation of fluorescent substances, such as the polymerization of flavan-3-ols. In conclusion, microwave treatment could modify the sensory characteristics of wine, and further provide the theoretical basis for the application of microwave in winemaking.

There has been controversy around the mechanical properties of Mg-alloys such as AZ91D and the large variation of these have been seen. The current paper addresses this controversy through specially fabricated samples combined with tensile testing and advanced metallography, including 3D reconstruction of the phases. The results show that despite a more brittle nature of the fracture, the equiaxed microstructure displays a better elongation as compared to a dendritic microstructure. The main conclusion is that this is primarily caused by the nature, or tortuosity, of the Mg17Al12-network in the material.

When developing bone implants Young's modulus is one of the primary characteristics of the material that should be considered. The study focuses on the possibility of regulating the modulus of the alloy Ti-50.8 at % Ni by varying its initial structure as well as aging-induced microstructure in a wide range. Microstructure observations were performed using TEM and SEM observations. The calorimetric studies of martensitic transformations were carried out using "Mettler Toledo 822e". Tensile tests were performed in a test temperature range of ‒196≤T≤+100°C using an «IN-STRON 5966». The grain/subgrain size of B2-austenite strongly affects the modulus magnitude. This effect is ambiguous for a material with a grain size of 0.13–3 µm and depends on the test temperature. The effectiveness of aging on the modulus reduction depends on the initial structure: it is most pronounced in an alloy with a relatively coarse grain size of 9 µm and brings a decrease by 3.8 times at a temperature of 37°C. Bone-like elastic modulus (10–30 GPa) at a human body temperature of 37°C is realized in an aged fine-grained NiTi alloy. An ultrafine-grained sub-structure exhibits he same values of Young's modulus in the temperature range from -100°С to 25°С.

The Sentinel Application Platform (SNAP) architecture facilitates Earth Observation data processing (http://step.esa.int/main/toolboxes/snap/). In this work we present results from a new Snow Processor for SNAP. We also describe physical principles behind the developed snow property retrieval technique based on the analysis of Ocean and Land Colour Instrument (OLCI) onboard Sentinel-3A/B measurements over clean and polluted snow fields. Using OLCI spectral reflectance measurements in the range 400-1020nm, we derive important snow properties such as spectral and broadband albedo, snow specific surface area, snow extent and grain size on the spatial grid of 300m. The algorithm also incorporates cloud screening and atmospheric correction procedures over snow surfaces. We present validation results using ground measurements from Antarctica, the Greenland ice sheet and the French Alps. We find the spectral albedo retrieved with accuracy of better than 3% on average, making our retrievals sufficient for a variety of applications. Broadband albedo is retrieved with the average accuracy of about 5% over snow. Therefore, the uncertainties of satellite retrievals are close to experimental errors of ground measurements. The retrieved surface grain size shows good agreement with ground observations. Snow specific surface area observations are also consistent with our OLCI retrievals. We present snow albedo and grain size mapping over the inland ice sheet of Greenland for areas including dry snow, melted/melting snow and impurity rich bare ice. The algorithm can be applied to OLCI Sentinel-3 measurements providing an opportunity for creation of long – term snow property records essential for climate monitoring and data assimilation studies - especially in the Arctic region, where we face rapid environmental changes including reduction of snow/ice extent and, therefore, planetary albedo.

Precipitation processes are technologies commonly used in hydrometallurgical plants to recover metals or to treat wastewaters. Moreover, solid-liquid separation technologies, such as thickening or filtering, are relevant unit operations, included in the precipitation technologies. These methods are strongly dependent on the characteristics of the solid precipitates formed during the specific precipitation reaction. One of these characteristics is the particle size distribution (PSD) of the solid precipitates which are fed into a solid-liquid separation process. Therefore, PSD determination is a typical practice for the characterization of the slurries generated in a precipitation plant. Furthermore, the precipitates generated in these processes have a colloidal or aggregation behavior, depending on the operational conditions. Nevertheless, the conventional methods used to estimate PSD (e.g., laser diffraction and/or ciclosizer) have not been designed to measure particles that tend to aggregate or disaggregate, since they include external forces (e.g., centrifugal, agitation, pumping and sonication). These forces affect the true size of the aggregates formed in a unit operation, thereby losing representativity in terms of aggregates particle size. This study presents an alternative method of measuring the size distribution of particles with aggregation behavior, particularly, by using non-invasive microscopy and image processing and analysis. The samples used have been obtained from an experimental precipitation process by applying sulfidization to treat the cyanide-copper complexes contained in a cyanidation solution. This method has been validated with statistical tools and compared with a conventional analysis based on laser diffraction. Our results show significant differences between the methods analyzed, demonstrating that image processing and analysis by microscopy is an excellent and non-invasive alternative to obtaining size distribution of aggregates in precipitation processes.

In order to investigate the size distributions and seasonal variations of carbonaceous aerosols (OC and EC), the carbonaceous species were collected and then analyzed by using a 9-stage Anderson-type aerosol sampler and DRI Model 2001A Thermal/Optical Carbon Analyzer on the typical industrial city Nanjing in Yangtze River Delta, China in the summer, autumn and winter of 2013 and spring of 2014. OC, EC, SOC and POC exhibited obvious seasonal variations, with the highest level in winter (39.1±14.0, 5.7±2.1, 23.6±11.7 and 14.1±5.7 μg•m^-3) and the lowest level in summer (20.6±6.7, 3.3±2.0, 12.2±3.8 and 8.4±4.1 μg•m^-3), and were mainly centralized in PM_1.1 in four seasons. The concentrations of OC in PM_1.1 varied in the order of winter > autumn > spring > summer, while EC ranked in the order of autumn > winter > summer > spring. In the PM_1.1-2.1 and PM_2.1-10, the concentrations of OC and EC decreased in the sequence of winter > spring > autumn > summer. The size spectra of OC, EC and SOC had bimodal distributions in four seasons, except for EC with four peaks in summer. The size spectra of POC varied greatly with seasons, exhibiting bimodal distribution in winter, trimodal distribution in spring and summer, and four peaks in autumn. The OC/EC ratios were 7.0, 6.3, 7.6 and 6.9 in spring, summer, autumn and winter, respectively, which demonstrated the abundance of secondary organic aerosols in Nanjing. The sources of carbonaceous aerosol varied significantly with seasons, and were dominated by vehicle exhaust, coal and biomass burning in PM_2.1, and dominant by dust, coal and biomass burning in PM_2.1-10.

The present study was conducted the status of sea bass from Kokko and Kyuntone of The Gulf of Motttama Wetland (GoMW) area in Thanatpin Township in Bago Region Myanmar from September 2019 to August 2020. Fifty specimens were monthly collected, measured and weighed. Invoices of sea bass were collected for the depot and fish sellers by monthly. In Kokko, mean value of standard length and body weight were highest in March (32.70±1.58, 660.7±112.23). The mean value of standard length was peak in January (31.39±7.16) but peak of body weight was in March (963.24±280.86) in Kyuntone villages. The lowest mean value of standard length and body weight were found in June at both study areas. According to the invoice data revealed that monthly catch weight of sea bass is most abundance in October (829.92) kg in Kokko, (339.12) kg in Kyuntone. Based on price of relations to size group, small size C < 300g (41%) was mostly abundance in Kokko and in Kyuntone small size C < 300g (35%) was second abundance. Specimens were not landed in April and May. In June, young specimens were very rarely seen in both study sites. The important roles of wetland fishes, the economic valuation of GOMW in Myanmar and samples of fishing gear and value chain of sea bass in Myanmar was expressed in this study.

Background: Globally, hot cooked refined rice is consumed in large quantities and is a major contributor to dietary glycaemic load. This study aimed to compare the glycaemic potency of hot and cold stored parboiled rice to widely available medium grain white rice. Method: Twenty-eight healthy volunteers participated in a three treatment experiment where postprandial blood glucose was measured over 120 minutes after consumption of 140g of rice. Three rice samples were freshly cooked medium-grain white rice, freshly cooked parboiled rice, and parboiled rice stored overnight at 4 ºC. All rice was served warm at 65 ºC. Chewing time was recorded. Results: The 24-hours cold-stored and reheated parboiled rice resulted in a 42% and 12% lower blood glucose concentration trajectory than freshly cooked medium-grain white rice and freshly cooked parboiled rice. Chewing time for 10g cold stored parboiled rice was 6 seconds (25%) longer and was considered more palatable, visually appealing and better tasting than freshly cooked medium grain (all P<0.05). Conclusions:. For regular consumers of rice reheating cooked rice after cold storage would lower the dietary glycaemic load and long term may reduce risk for type 2 and gestational diabetes. More trials are needed to identify the significance.

The study delves into the critical examination of the Size of Loss distribution patterns in the context of auto insurance during pre- and post-pandemics, emphasizing their profound influence on insurance pricing and regulatory frameworks. Through a comprehensive analysis of the historical Size of Loss data, insurers and regulators gain essential insights into the probabilities and magnitudes of insurance claims, informing the determination of precise insurance premiums and the management of case reserving. This approach aids in fostering fair competition, ensuring equitable premium rates, and preventing discriminatory pricing practices, thereby promoting a balanced insurance landscape. The research further investigates the transformative impact of the COVID-19 pandemic on these Size of Loss patterns, given the substantial shifts in driving behaviors and risk landscapes. Also, the research contributes to the literature by addressing the need for more studies focusing on the implications of the COVID-19 pandemic on pre- and post-pandemic auto insurance loss patterns, thus offering a holistic perspective encompassing both insurance pricing and regulatory dimensions.

A study was carried out in a Waste Sorting Plant (WSP) located in France and treating dry recyclable household waste (DRHW) as well as dry recyclable commercial and industrial waste (DRCIW). The aim was to investigate the exposure to bioaerosol and dust. The aim of the study was to assess the extent to which the measurement of concentration, species composition and particle size distribution can contribute to a better assessment of the biological risks associated with exposure. Both stationary and personal bioaerosol and dust samples were collect in the (WSP). The results confirm that waste and waste sorting activities are sources of airborne fungi. Indeed, ambient concentrations ranged from 7.3×103 to 8.5×105 CFU/m3 for culturable moulds and up to up to 4 mg/m3 for dust. Personal exposure to inhalable dust was found up to 3 mg/m3 for dust and ranged from 8.6×103 to 1.5×106 CFU/m3 for fungi. Airborne fungal communities were found to be dominated by the Penicillium genera in both bioaerosols and settled dust samples, followed by the Aspergillus, Cladosporium, Wallemia, Mucor, and Rhizopus genera. Fungi were carried by particles of aerodynamic diameters mainly between around 2.0 and 10.0 µm. The findings dealing with size distribution and biodiversity of bioaerosols suggest that employees are exposed to complex bioaerosols during their work and helps to make a finer diagnosis of the risks involved, which is often difficult in the absence of any OEL for bioaerosols in general.

Variable and sometimes contrasting effects of using artificial rhizobium inocula to increase grain legume performance have been reported. The objectives of this systematic review and meta-analysis were therefore to (i) estimate the overall effect of rhizobium inocula on grain yield and protein content and (ii) identify potential confounding factors that explain the observed variation. A web of Science database literature search was carried out in 2016. Data from all field experiments, greenhouse and pot experiments that compared grain yields and protein contents in Rhizobium/Bradyrhizobium-inoculated with non-inoculated control crops were extracted and analyzed using previously described unweighted and weighted meta-analysis protocols. GRADE assessments of the strength of evidence of results from the weighted meta-analyses were carried which included an assessment of the risk of publication bias. Results: For unweighted meta-analyses we identified eligible data in 236 and 36 studies for grain yield and protein content respectively. For weighted meta-analyses we identified eligible data in 92 and 8 studies for grain yield and protein content respectively. Rhizobium inoculation was found to (i) significantly increase grain yield in both the unweighted (mean percent difference: 41%, 95%CI 36,46, p&lt;0.0001) and weighted meta-analysis (Standardized mean difference: 1.56, 95%CI 1.26,1.87, p&lt;0.0001) and (ii) significantly increase protein content in the unweighted meta-analysis (mean percent difference: 11%, 95%CI 5,18, p&lt;0.0001), but not the weighed meta-analyses which only detected a trend (0.1&gt;p&gt;0.05) towards higher protein content in inoculated grain legume crops. Multi-level model-based weighted meta-analyses suggest that the (i) type of experiment, (ii) type of fertilizer used in experiments, (iii) grain legume type/species and (iv) the country in which experiments were carried out, were confounding factors. The main limitation of the evidence is that a large number of publications did not report measures of variation and could therefore not be included in the more scientifically sound weighted meta-analyses. However based on the large evidence-base available for grain yield it can be concluded that overall Bradyrhizobium/Rhizobium seed inoculation results can increase grain yield by ~40% compared with non-inoculated grain legume crops.

The paper investigates the possible use of a low strength domestic sand (D) (up to today useless – not considered as proppant source) of small particle sizes, instead to that of high strength imported commercial sand (C), as a prospective micro-proppant for low permeability reservoirs in Poland. There is need to develop national unconventional gas resources like tight gas, shale gas and coalbed methane. An important energy source of value and readily available in Poland is coal. The basins of this resource are large and bears low permeability coalbed methane reservoirs which needs to be developed to contribute to the energy security, economy and environmental needs of the country. These reservoirs need technological assistance such as hydraulic fracturing which makes use of proppants for development. Most of the commonly used proppants over the years for fracturing have been large grain size commercial proppants of high strength material content bought abroad. Investigated finer proppants are known to have the ability to penetrate narrow fracture networks to ensure effective high reservoir volume and conductivity for production. Results from presented laboratory research shows the D - proppant, which is cheaper and readily available, has the 3K class with low settling rates as a potential micro-proppant for effective transportation, enhancement of conductivity and production rate in the narrow fractures of low permeability reservoirs. Future using of domestic proppant will decrease stimulation cost and will have positive impact on the environment due to omitting long distance transportation from abroad.

We present new results in positron annihilation lifetime spectroscopy (PALS), thermo-optical dilatometry and microscopy, which are indicating a strong correlation between grain-boundaries and mass transport during the sintering process of carbonyl iron powder. In this particular system we were able to show that the change in particle shape and size with increasing temperature yields an anisotropy in shrinkage, which manifests itself in a higher shrinkage perpendicular to the compaction axis. In the intermediate stage of sintering, where the major mass transport occurs, the average distance between two grain boundaries could be determined to (3,73 ± 0,18) μm at T = 744°C. This is in good agreement with previous calculations of positron pathways in defect free particles. Furthermore, due to sintering temperatures far above the annealing temperature of dislocations in iron, the existence of dislocations in the bulk of the particles is very unlikely. These claims are reflected by the collected positron data, which exhibit a clear grain boundary signal of ∼ 250ps while no vacancy or dislocation signal (typically ∼ 160 ps) is evident in the intermediate stage of sintering.

In an increasingly resource-constrained era, the utilization approach of waste and by-products from grain processing, is attractive widely, considering both nutritive value and economic aspects and move towards more sustainable food systems. Following the fundamentals of a circular economy, the need of the hour lies in its effective utilization as a grain waste and by-products conversion into value-added products in food industry. The aim of this study is twofold: 1. Understanding the progress of grain waste and by-products to valorization in human nutrition, using bibliometrics; different literature databases namely Google Scholar, Web of Science and Elsevier Scopus have been evaluated for their merits and values; 2. Exploration of knowledge-based strategies, by reviewing the literature concerning the possible use of grain waste and by-products for food processing industry, reducing burden on virgin raw materials. The review allowed to unlock the latest-advances of upcycling side streams and waste from grain processing industry.

X-band dual-polarization phased array radar (XPAR-D) possesses high temporal-spatial resolutions and plays a significant role in detecting meso- and micro-scale convective systems. However, the precipitation attenuation it endures necessitates an effective correction method. This study selected radar data from XPAR-D at the peak of Maofeng Mountain in Guangzhou during May 16-17, 2020 from three precipitation stages after quality control. Attenuation coefficients are calculated for different precipitation types through scattering simulations of raindrop size distribution (RSD) data. Drawing upon this, an attenuation correction algorithm (MZH-KDP method) is proposed for radar reflectivity factor (ZH) according to different raindrop types, and is compared to the ZH-KDP method currently in use. The results indicate that the attenuation amount of XPAR-D echoes depends on the attenuation path and echo intensity. When the attenuation path is shorter and the echo intensity is weaker, the amount of attenuation and correction is smaller. Difficulties arise when there are noticeable deviations in such a situation, which are challenging to solve via attenuation correction methods. Longer attenuation paths and stronger echoes highlight the advantages of the MZH-KDP method, while the ZH-KDP method tends to overcorrect the bias. The MZH-KDP method outperforms the ZH-KDP method for different precipitation types. The superior correction capability of the MZH-KDP method provides a significant advantage in improving the performance of XPAR-D for the detection of extreme weather.

Genetic enhancement of grain production and quality is a priority in wheat breeding projects. In this study, we assessed two key agronomic traits - grain protein content (GPC) and thousand kernel weight (TKW) - across 179 Bulgarian contemporary and historic varieties, and landraces in three growing seasons. Significant phenotypic variation existed for both traits among genotypes and seasons, and no discernible difference was evident between the old and modern accessions. To understand the genetic basis of the traits, we conducted a genome-wide association study with MLM using phenotypic data from the crop seasons, best linear unbiased estimators, genotypic data from the 25K Infinium iSelect array, and a Bonferroni-adjusted p-value. As a result, 776 significant quantitative trait nucleotides (QTNs) organized into quantitative trait loci were discovered, including 25 loci associated with GPC, and 35 loci linked to TKW. Additionally, 14 environmentally stable QTNs were identified for TKW. Certain loci on chromosomes 2A, 3A, and 6B favorably in-fluenced GPC, while the locus on chromosome 6D impacted TKW positively. These loci may reflect novel associations to the two traits. Annotations for proteins involved in the remobilization of carbon and nitrogen from vegetative tissues to developing grain during senescence, as well as in the following buildup of resources required for seed germination, have been found for selected pu-tative candidate genes. These include genes coding for 11S globulin seed storage protein, glutamine synthetase, metalloendopeptidase, components of the ubiquitin/proteasome system, sucrose transporter, alpha-amylase, NAC and bZIP transcription factors. Our findings highlight promising genomic regions for targeted breeding programs aimed at improving grain yield and protein content.

The leading role of Italy in the cultivation of durum wheat stimulated intense breeding activities in the country from the beginning of the 20th century, much earlier than any other country involved in durum wheat production. Older, genetically more heterogeneous landraces became replaced with new highly productive, superior quality varieties, and this led an inevitable reduction in overall genetic diversity among new cultivars, which makes the genetic variability of the old cultivars preserved particularly valuable and important. The aim of this paper was to assist future breeding programmes by providing a detailed description of the history of durum wheat breeding in Italy and of the changes in yield, quality and related traits that subsequently occurred, starting from the most diffuse landraces present between 1900 and 1920 up until the present day. The parallel evolution of breeding techniques, breeding goals and agricultural systems in this period is also described, and some future breeding goals suggested. In the current context of climate change and of rapidly mutating pathogen populations, preserving the yield level with the continuous introduction of new cultivars by exploiting the reservoir of largely unused genetic variation stored in old cultivars and landraces could be as important as increasing grain yield and quality.

: Our study aim to test the influence of RGB reflectance and chlorophyll content on grain fill and grain yield of 15 durum wheat cultivars sown under semi-arid conditions. the evolution of chlorophyll content during three stages showed a stability during the heading stage, the chlorophyll content begins at this degradation during grain filling. Boutaleb genotype which was the best yielding genotype was characterized by low values ​​of RGB reflectance and high values ​​of majority of grain filling parameters and thousand kernels weight. Grain filling follows a sigmoid curve. Chlorophyll content was positively correlated with reflectance under the green band and negatively with both Red and Blue bands. A positive correlation was recorded between thousand kernel weight and grain yield, maximum grain dry weight and grain filling duration. The duration of the grain filling was positively influenced by the maximum dry weight of the grain and negatively by the grain filling ratio, the grain filling ratio was positively affected by reflectance at blue band. The principal component analysis separated the cultivars considered into 3 principal components, the absorption/reflectance component, the profitability component and the component of grain filling rate to which the local landrace Boutaleb belongs in terms of grain yield.

The thorough description of the peculiarities of additively manufactured structures represents a current challenge for aspiring freeform fabrication methods, such as the selective laser melting (SLM). All of which have an immense advantage in the fast fabrication (no special tooling or moulds required), the geometrical flexibility in the design of components, and their efficiency when only low quantities are required. However, designs demand the precise knowledge of the material properties, which in case of additively manufactured structures are anisotropic and, under certain circumstances, in addition of an inhomogeneous nature. Furthermore, these characteristics are highly dependent on the fabrication settings. Within this study, the anisotropic tensile properties of selective laser melted stainless steel (1.4404, 316L) are investigated: The Young’s modulus ranged from 148 GPa to 227 GPa, the ultimate tensile strength from 512 MPa to 699 MPa and the breaking elongation ranged, respectively, from 12% to 43%. The results were compared to related studies, in order to classify the influence of the fabrication settings. Furthermore, the influence of the chosen raw material was addressed by comparing deviations on the directional dependencies reasoned by differing microstructural developments during manufacture. Stainless steel was found to possess its maximum strength at a 45° layer versus loading offset, which is precisely where AlSi10Mg was previously reported to be at its weakest.

CONTEXT: The sustained White corn (Zea mays L.) yield relies on supply of Nitrogen (N), which is an important element in improving soil fertility. OBJECTIVE: The research aim to determine the effect of Nitrogen on white corn yield and grain mass. METHOD: The experimental design was a 4 × 4 factorial arranged in randomized complete block design with 2 replications each. The effect of nitrogen was determined in terms of the flow within the soil, initial component, addition, uptake, loss and use of nitrogen by the White corn plants. Nitrogen was applied as Granular Urea using zero broadcast method. The grain yield was determined hand-harvesting and shelling. RESULTS AND CONCLUSIONS: There were no statistically significant differences between the mean samples from the two replicates (blocks 1 & 2) across the two seasons for corn sugar concentration, corn yield estimates and grain yields. In 2021, the mean yield estimate was 12,552 Kg ha-1, while that of 2022 averaged 12687 Kg ha-1. Similarly, the grain yield achieved in 2022 was 844.1kg more than the average grain yield in 2021. The white corn yield estimate and grain yield increased linearly with an increase in nitrogen application level, with the highest yields achieved when nitrogen fertilizer was applied at 150kg N/ha. This demonstrates that nitrogen has a positive influence on the yield quantity of white corn. SIGNIFICANCE: The White maize model may be used to improve the formulation of decisions and enhance the precision of estimates for yield and N fate within the soil-plant-atmosphere continuum. Further, the findings of this study can significantly enhance agricultural productivity while keeping an eye on the environment.

Recent studies on seafloor mapping have presented different modelling methods for the automatic classification of seafloor sediments. However, most of these studies have applied these models to seafloor data with appropriate number of ground-truth samples, which raises the question whether these methods are applicable to studies with smaller numbers of ground-truth data. In this study, we aim to address this issue by conducting sediment class-specific predictions using ensemble modelling to map areas with limited or without ground-truth data and combined with hydro-acoustic datasets. The resulting class-specific maps were then assembled into one map, where the most probable class was assigned to the appropriate location. Our approach was able to predict sediment classes without bias to the class with more ground-truth data and produced reliable seafloor sediment distributions maps that can be used for seafloor monitoring. Sediment shifts of a heterogenous seafloor in the Sylt Outer Reef, German North Sea were also assessed to understand the sediment dynamics in the area. The analyses of sediment shifts showed that the western area of the Sylt Outer Reef is highly active, and the results of the analyses assisted in providing recommendations on future seafloor monitoring activities.

The microstructure evolution and grain refinement kinetics of a solution treated Cu – 0.1Cr – 0.06Zr alloy during equal channel angular pressing (ECAP) at a temperature of 673 K via route B_C were investigated. The microstructure change during plastic deformation was accompanied by the microband formation and an increase in the misorienations of strain-induced subboundaries. The refinement of initial coarse grains was considered as a result of continuous dynamic recrystallization. The dynamic recrystallization kinetics was discussed in terms of grain/subgrain boundary triple junction evolution. The strain dependence of the triple junctions of high-angle boundaries can be expressed by a modified Johnson-Mehl-Avrami-Kolmogorov relationship with a strain exponent of about 1.49. Severe plastic deformation by ECAP led to substantial strengthening of the Cu-0.1Cr-0.06Zr alloy. The yield strength increased from 60 MPa in the initial state to 445 MPa after the total strain of 12.

Background: Previous in vitro and in vivo studies have demonstrated that storage of cooked rice at 4 °C for 24 h and reheating to 65 °C significantly reduced starch digestibility and postprandial glycaemic responses. Moreover, the effect was greater for parboiled rice compared to other rice varieties commonly consumed in New Zealand. This study aimed to evaluate consumer preferences of related sensory attributes and consumer acceptability of several rice varieties freshly cooked or reheated. Method: Sixty-four consumers volunteered and recorded on Visual Analoge Scales their preference and acceptability of freshly prepared or cold-stored and reheated medium grain white, medium grain brown and parboiled rice. Results: All six rice samples were accepted by participants (average 54%). Reheated parboiled rice and reheated medium grain brown rice were both accepted by participants as a preferred staple meal compared to other rice samples. Among all rice samples, the sweetness and the flavour of freshly cooked warm medium-grain white rice were less preferred (scored 42.1% and 45.0% respectively) compared with other samples (P = 0.05). Participants who prepared and consumed brown rice at home regularly (more than 10 times per month), preferred the reheated brown rice (73.8% (67.4, 80.2)) and reheated parboiled rice (74.3% (67.9, 80.7)) (P < 0.001). Conclusions: It is suggested that reheated parboiled rice, with the lowest starch digestibility and glycaemic impact (both in vitro glucose release and in vivo glucose response) could be accepted as a healthier alternative for the daily staple meal.

Abstract: The objective of these studies was to determine the dependence of the distribution of the microwave field into a grain layer and the efficiency of energy transfer from the magnetron into the grain layer, via a waveguide, on the moisture content. The subject of the research was a semicircular waveguide with slot radiators that supply a microwave field to the grain surrounding the waveguide. The change in the directional diagram of the microwave field in the longitudinal direction of the waveguide was studied using CST Microwave Studio 2019 software. It was found that the change in the moisture content of the processed grain leads to a significant change in both the radiation and total efficiency values of the waveguide. For instance, the radiation efficiency of the waveguide decreases by 15.1% (from 68.729 dB to 58.294 dB) when the moisture content of the processed grain increases from 14% to 26%. The total radiation efficiency also decreases (from 11.27 dB to 21.7 dB). In this case, not only the value of the radiation efficiency but also the shape of its dependence on the magnetron radiation frequency change. Data were obtained on the change in the Q-factor for resonators in which grain layers are processed, depending on the variation in grain moisture content.

This work describes and interprets the presence of heavy minerals in the western Portuguese continental margin using a set of 78 bottom samples collected from 3 distinct areas of this margin: Porto, Aveiro and Nazaré canyon head areas. The main transparent heavy mineral suite (minerals with frequencies >10%), is composed by amphiboles (hornblende), mica (biotite), andalusite, tourmaline and garnet. A secondary suite (minerals with frequencies between 1 and 10%), is composed by pyroxene (enstatite, diopside and augite), staurolite, zircon and apatite. With very low frequency representing less than 1% we found rutile, olivine, kyanite, monazite, epidote, sphene, anatase, sillimanite and brookite. The main primary sources (igneous and metamorphic rocks) explain the presence of these minerals. However, the application of the principal component analysis, with a previous application of the centered log ratio transformation of the heavy mineral data, also stresses for the importance of the grain sorting as a process in controlling the heavy mineral occurrence. The importance of this process is mostly sustained by the distribution pattern of mica and of the most flattened amphibole grains in a way that these particles tend to have a hydraulic affinity to finer grained sediments.

In a changing climate, extreme weather events such as heat waves will be more frequent and could affect grain weight and the quality of crops such as wheat, one of the most significant crops in terms of global food security. In this work, we characterized the response of Triticum turgidum spp. durum wheat to a short-term heat-stress (HS) treatment at transcriptomic and physiological levels during early grain filling in glasshouse experiments. We found a significant reduction in grain weight and size from HS treatment. Grain quality was also affected, showing a decrease in starch content in addition to increments in grain protein levels. Moreover, an RNA-seq analysis of durum wheat grains allowed us to identify 1590 differentially expressed genes related to photosynthesis, response to heat, and carbohydrate metabolic process. A gene regulatory network analysis of HS-responsive genes uncovered novel transcription factors (TFs) controlling the expression of genes involved in abiotic stress response and grain quality, such as a member of the DOF family predicted to regulate glycogen and starch biosynthetic processes in response to HS in grains. In summary, our results provide new insights into the extensive transcriptome reprogramming that occurs during short-term HS in durum wheat grains.

The manipulation of participant allocation in randomized controlled trials to achieve equal groups sizes may introduce allocation bias potentially leading to larger treatment effect estimates. This study aimed to estimate the proportion of nursing trials that have precisely equal group sizes and examine if there was an association with trial outcome. Data were extracted from a sample of 148 randomized controlled trials published in nursing science journals in 2017. One hundred trials (68%) had precisely equal group sizes. Respectively, a positive outcome was reported in 70% and 58% of trials with equal/unequal groups. Trials from Asia were more likely to have equal group sizes than those from the rest of the world. Most trials reported a sample size calculation (n=105, 71%). In a third of trials (n=36, 34%), the number of participants recruited precisely matched the requirement of the sample size calculation; this was significantly more common in studies with equal group sizes. The high number of nursing trials with equal groups may suggest nurses con-ducting clinical trials are manipulating participant allocation to ensure equal group size increasing the risk of bias.

Introduction: The purposes of this study were to seek for overall ratio (OR) and anterior ratio (AR) patients data in normal occlusion and Angle’s malocclusion studies, and to assess if such results support Bolton’s standards as general references. Methods: Pubmed, Medline, CENTRAL and Scholar databases were searched up to February 2018 (CRD42018088438). Gray literature was explored through OpenGray. Non-randomized clinical studies, published in English and assessing Bolton’s OR and AR in normal occlusion and Angle’s malocclusion groups (Class I, Class II, Class II division 1, Class 2 division 2, Class III) patients were included. OR and AR means and standard deviations (SD) were collected. Potential covariates (study design, publication year, country where the study was conducted, number of cases, gender, mesiodistal measurement method, and calibration method) were also extracted. The National Health Heart Lung, and Blood Institute’s Quality Assessment Tool for Observational Cohort and Cross-Sectional Studies was used to assess each included studies quality. Pairwise Random-Effects and Multilevel Bayesian Network Meta-Analyses were used to synthesize available data. Results: Fifty-two observational studies were included (8872 participants; male/females 2674/3272; 16 studies lacked gender information). For normal occlusion, global pooled estimates for OR and AR means were 91.74% (95% CI: 91.37-92.10) and 78.24% (95% CI: 77.85-78.63), respectively. We could identify on Angle’s Class III patients meaningful OR and AR mean deviations from normal occlusion (0.89, 95% credible interval [CrI], 0.66-1.12, and 0.66, 95% CrI, 0.38-0.94, respectively), while on Class I patients we found a meaningful mean deviation from normal occlusion only for OR (0.25, 95% CrI, 0.03-0.47). Concerning gender impact, male patients presented higher OR (0.30, 95% CI 0.00-0.59) and AR (0.41, 95% CI 0.00-0.83) mean values than females in Class I. Conclusions: The results show that global pooled OR and AR mean values for normal occlusion patients are slightly above Bolton’s original values. Class I, for OR mean values, and Class III, for both OR and AR, are proportionally larger than normal occlusion patients. Gender had almost no impact on teeth mesiodistal proportion.

Grain legumes are fair sources of protein, amino acids and energy, and can be used as a replacement for soybean meal in poultry feed formulations as the soybean meal becomes short in supply and costly. However, a concern associated with the use of grain legumes in poultry feeding is the presence of antinutritional factors. Effective processing and utilisation of these grain legumes in poultry feeding are well documented. The current review focuses on four selected grain legumes (lupins [Lupinus albus and Lupinus angustifolius], field peas [Phaseolus vulgaris], faba beans [Vicia faba] and chickpeas [Cicer arietinum]) and their nutrient content, the presence of antinutritional factors, processing methods and feeding value, including updated data based on recent research findings.

Portugal’s EPAC silo network, initially planned in the 1930s but constructed and utilized primarily in the 1970s, consisted of 31 silos with a total capacity of 841,100 t. The network’s usage declined, however, due to market liberalization and Portugal’s accession to the European Economic Community in 1985. This study focuses on adapting a methodology to inventory and analyse the 31 silos in the EPAC network considering their general features, construction, technological facilities, and socioeconomic aspects. The silos are situated in 30 cities and towns, predominantly in the country’s key grain-growing regions, particularly the Alentejo region. While there are variations in design and construction, most EPAC silos contain two or three rows of circular reinforced-concrete cells and use the spaces between cells for storage. Their capacities range from 6,000 to 35,000 t. Some are inland grain reception and storage silos, while others are larger-capacity port silos designed to unload grain rapidly onto ships using mechanical or pneumatic unloaders. These structures are a significant part of Portugal’s agro-industrial heritage and have in some cases been repurposed as museums or event venues. Compared to other agro-industrial buildings, silos pose unique conversion challenges due to their height and design complexities. Examples of successful reuse in countries like Spain and Italy may provide insights for potential silo projects in Portugal. However, analysis suggests that such proposals and similar initiatives may be viable only in the more highly populated towns.

In rye, there is a considerable variety of grain color which is determined by the diversity of compounds localized in different parts of the grain (caryopsis) - pericarp, testa, and aleurone. The localization of anthocyanins and proanthocyanidins was analyzed in 26 rye samples with identified anthocyanin genes, along with the analysis of CIE color coordinates. The Grain Scan program [1] was used to analyze images of individual grains. The localization of anthocyanins and proanthocyanidins was studied on longitudinal and cross sections of grains using light microscopy and MALDI-imaging. The violet-grained samples contain anthocyanins in the pericarp, and the green-grained samples contain anthocyanins in the aleurone layer. The green, violet and yellow-grained rye, with the exception of two anthocyaninless mutants vi3 and vi6, shows the presence of proanthocyanidins in the brown-colored testa. Four main color groups of the rye grains (yellow, green, brown, violet) could be differentiated using the color coordinate h° (hue angle). Interspecies and intraspecies variability for the localization of colored flavonoids in cereal grains is discussed.

Concretizing the mechanisms of Bergmann rule, we found saw-tooth pattern in body size variation in ground beetle Pterostichus oblongopunctatus. We sampled beetles in 2010 – 2018 at the forest undisturbed plots on the broad territory in Russia. Investigating regions covered territory, extending to 3 degrees latitude and 19 degrees longitude. We measured six traits in every of 3294 caught individual. ANOVA showed that latitude, and sex affected significantly body size of the species studied. Mean values of each trait changed significantly from one studied region to another in females and males as well. Sexual size dimorphism in species was female-biased. We performed models in R to estimate the steepness of body size variation in both sexes. In overwhelming majority of cases that parameter was equal in both sexes. So the hypothesis, that male′s variation is steeper in latitude gradient was not confirmed.

This paper presents a new approach of eddy current methods for determining the size of the co-axial hole in the metallic circular disk. In recent decades, for the air-cored sensor probe, the impedance change due to the presence of an infinite metal plate can be calculated by the Dodd-Deeds model. However, in practical measurements, the sample cannot match with the condition required - ‘infinite’, thus the Dodd-Deeds model could not be applied to the disk with finite size and certainly not a co-axial hole in the center. In this paper, a dual-constraint analytical method is proposed. That is, the upper and lower limits of the integration are substituted with specific values instead of the original 0 and . Besides, it is found that, once the outer radius of the disk is fixed (i.e. the lower limit of integration is fixed), the upper limit reduces linearly as the size of the coaxial hole increases. Both the FEM simulation and experiments have been carried out to validate this method. The radius of the hole can be estimated based on the dual-constraint integration feature.

Thin Slab Casting and Directing Rolling (TSCDR) has become a major process for flat- rolled production. However, the elimination of slab reheating and limited number of thermomechanical deformation passes leave fewer opportunities for austenite grain refinement resulting in some large grains persist in the final microstructure. In order to achieve excellent Ductile to Brittle Transaction (DBTT) and Drop Weight Tear Test (DWTT) properties in thicker gauge high strength low alloy products, it is necessary to control austenite grain coarsening prior to the onset of thermomechanical processing. This contribution proposes a suite of methods to refine the austenite grain from both theoretical and practical perspective including: increasing cooling rate during casting, liquid core reduction, increasing austenite nucleation sites during the delta ferrite to austenite phase transformation, controlling holding furnace temperature and time to avoid austenite coarsening, and producing new alloy with two phase pinning to arrest grain coarsening. These methodologies can not only refine austenite grain size in the slab center, but also improve the slab homogeneity.

The grain filling rate (GFR) plays a crucial role in determining grain yield. However, the regulatory and molecular mechanism of grain filling rate (GFR) in foxtail millet remains unclear. In this study, we found the GFR of 'Changnong No.47' (CN47) was significantly higher at 14 days after flowering (DAF) and 21 DAF in comparison to 'Changsheng 13' (CS13). Furthermore, CN47 also exhibited higher thousand grain weight and yield than CS13. Therefore, we conducted transcriptomics and metabolomics to analyze the biological processes and functional genes associated with GFR during two stages of grain filling in both cultivars. A total of 765 differentially expressed genes (DEGs) and 246 differentially accumulated metabolites (DAMs) were identified at the 14 DAF stage, while at the 21 DAF stage, a total of 908 DEGs and 268 DAMs were identified. The integrated analysis of co-mapped DAMs and DEGs revealed enriched pathways, including flavonoid biosynthesis, plant hormone signal transduction, tyrosine metabolism, ATP-binding cassette (ABC) transporters, beta-alanine metabolism, as well as stilbenoid, diarylheptanoid and gingerol biosynthesis. In order to elucidate their potential functions in the context of GFR, we developed a gene-metabolite regulatory network for these metabolic pathways. Notably we found some genes associated with ABC transporters and plant hormone signal transduction pathway were implicated in auxin transport and signal transduction, highlighting the crucial role of auxin during grain filling. The results provide initial insights into the regulatory and molecular mechanisms underlying GFR in foxtail millet, as well as offer valuable genetic resources for further elucidation of GFR in future studies. The findings have established a theoretical basis for improving the efficiency of yield breeding in foxtail millet.

Conservation tillage and deep side-fertilization both hold the potential to reduce nitrogen leaching and improve grain yield and nitrogen use efficiency in fragrant rice cultivation practices. However, the combined impact of different tillage practices with deep side-fertilization on nitrogen leaching remains uncertain. Therefore, this study conducted on-site experiments for four rice growing seasons in both early and late seasons in 2018 and 2019, using the fragrant rice varieties "Meixiangzhan 2"(MX) and "Xiangyaxiangzhan"(XY). The four experimental treatments included:conventional tillage with regular fertilization (T1), conventional tillage with simultaneous deep fertilization (T2), reduced tillage with simultaneous deep fertilization (T3) , and no-tillage with simultaneous deep fertilization (T4). Our results indicate that the T4 treatment exhibited higher nitrogen leaching rates and potential nitrogen losses throughout the entire rice growth cycle, with a 4.51% increase in total nitrogen leaching and a 1.86% increase in potential nitrogen leaching compared to T1. In contrast, the T2 treatment demonstrated the lowest nitrogen leaching rate, resulting in a 6.01% reduction in total nitrogen leaching and a 9.57% decrease in potential nitrogen leaching compared to T1, demonstrating the most optimal performance. For MX, the T1 treatment resulted in lower daily grain outputs compared to the other treatments, with disparities ranging from 5.35% to 9.94%. Similarly, for the XY, the T1 treatment yielded significantly lower daily grain outputs compared to the other treatments, with discrepancies ranging from 6.26% to 10.81% during the late season of 2019. Overall, this study shows that conventional tillage with deep fertilization effectively reduces nitrogen leaching and boosts fragrant rice yields. Minimizing nitrogen leaching enhances nitrogen utilization efficiency. These insights highlight the significance of strategic fertilization and cultivation for environmental conservation and agricultural sustainability.

Durum wheat is an economically and nutritionally important cereal. The increase in durum wheat yield is mostly associated with improving grain traits. The grain size and shape-related traits are directly related to wheat yield. In addition, grain size influences the seed germination rate and seedling vigour, which play key roles in stand establishment and yield. Thus, it is important to investigate grain traits both agro-morphologically and genetically. In this study, a panel of durum wheat, consisted of 146 genotypes, was evaluated for grain traits agro-morphologically, and a genome-wide association study (GWAS) was conducted to dissect the genomic regions associated with these traits. As a result of GWAS, a total of 41 marker-trait associations (MTAs) were identified on different chromosomes of durum wheat. Of these MTAs, only 11 were stable across environments. A BLAST search for flanking sequences of every stable MTAs in the Svevo genome identified 18 putative candidate genes directly associated with seed traits of different plants, particularly wheat seeds. In conclusion, the annotation results and literature information provide strong evidence that identified stable MTAs and their candidate genes may have important functions in the formation of wheat grain traits. After the validation of these MTAs with different fine-mapping and functional characterization studies, these loci may provide valuable information for geneticists and breeders to improve wheat yield.

Grain shape and chalkiness are important appearance quality traits of rice, which also affect the yield and milling quality. In this study, 190 F2 families derived from the cross between Hua 5178S and Hua 611 were sequenced to construct a genetic linkage map. Combined with F2 and F2:3 generations grain shape and chalkiness phenotype, a total of 15 QTL were detected. There are 8 grain shape QTL distributed on chromosomes 2, 5, 6, 8, and 10; 7 chalkiness QTL distributed on chromosomes 2, 3, and 6. A QTL cluster affecting multiple chalkiness traits was found on chromosome 6, qWBR6.1, qWCR6 and qCR6 were selected for genetic effect verification. It was found that qWBR6.1, qWCR6 and qCR6 explained 13% and 24%, and 29% of the phenotypic variations respectively, and qWCR6 and qCR6 were co-mapped. This study laid a foundation for further cloning of rice appearance quality genes.

Solute decoration at grain boundaries (GB) leads to a number of phenomenon such as changes in interface structure, mobility, cohesion etc. Recent experimental investigations on interfacial segregation in steels are based on microstructural characterisation using two correlative methodologies, namely, Transmission Electron Microscopy-Atom Probe Tomography (APT) and Electron Backscatter Diffraction-APT. Considering the growing interest in this avenue, the present review is aimed at addressing the common adsorption isotherms used for quantifying interfacial segregation and providing an overview of the present state of experimental research in the area of GB segregation in steels. The areas where an understanding of GB segregation may be utilised have also been highlighted with a focus on the experimental challenges associated with understanding GB segregation in steels.

Abstract: Molybdenum (Mo) thin films were sputtered from two kinds of Mo targets with different microstructures under the same sputtering process, and the effect of microstructure of Mo target on morphology, deposition rate and resistance of sputtered film were studied and discussed. The results show that morphological differences between Mo thin films sputtered by Mo targets with different microstructures are very small. The more uniform and finer the grain structures of Mo target, the better the uniformity on thickness and resistance of Mo sputtered film. Moreover, during sputtering process, when Mo target’s grain size is finer and the surface area of grain boundary is higher, the thickness reduction of the target is more homogeneous and the sputtering film has faster deposition velocity. The difference in microstructure of the Mo target has not obvious influence on the grain orientation of sputtering film.

Tanzania with 945 million hectares of land area and annual rainfall of 300 mm on 67% of its territorial land is considered as a semi-dry region in the world. Rice production in Tanzania needs to be increased to feed a growing population, whereas water for irrigation is getting scarce. One way to decrease water consumption in paddy fields is to change the irrigation regime for rice production and to replace continuous flooding with alternate wetting and drying. In order to investigate the effect of different regimes of irrigation and nitrogen fertilizer on yield and water productivity of hybrid rice, two greenhouse pot experiments comprising soils from upland and lowland production ecologies were conducted at Sokoine University of Agriculture, Tanzania during crop seasons of 2019. The experiment was arranged in split plots based on randomized completely block design with 3 replications. Water regimes were the main factor comparing continuous flooding (CF) and alternate wetting and drying (AWD) with nitrogen fertilizer levels as the sub-factor including absolute control , 0, 60, 90, 120 and 150 kg/ha. Alternate wetting and drying (AWD) improved water productivity in both upland and lowland production ecologies compared to CF. AWD increased yield under lowland production by 13.3% while in upland there was 18.5% decrease in yield. The average water use varied from 31.5 to 84 L pot-1 under upland trials, while in lowland trials it was 36 to 82.3 L. Higher yield and lower water application led to an increase in WP varying from 1.2 to 1.8 kg cm-3 under upland trials, and 0.6 to 1.5 kg cm-3 under lowland trials. The variation in water productivity among treatments was mainly due to the differences in the yield, water and nitrogen levels used in the production process. Both sets of trials recorded water saving up to 34.3% and 17.3% under lowland and upland trials, respectively. Under upland trials, the yield varied from 39.9 to 124.1 g pot-1 and in lowland trials yield ranged from 20.6 to 118.2 g pot-1 representing paddy rice. The measurements showed that less water can be used to produce more crops under alternative rice growing practices. The results are important for water-scarce areas, providing useful information to policy makers, farmers, agricultural departments, and water management boards in devising future climate-smart adaptation and mitigation strategies.

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

The implementation of graphene-based electronics requires fabrication processes able to cover large device areas since exfoliation method is not compatible with industrial applications. Chemical vapor deposition of large-area graphene represents a suitable solution having the important drawback of producing polycrystalline graphene with formation of grain boundaries, which are responsible for limitation of the device performance. With these motivations, we formulate a theoretical model of graphene grain boundary by generalizing the graphene Dirac Hamiltonian model. The model only includes the long-wavelength regime of the particle transport, which provides the main contribution to the device conductance. Using symmetry-based arguments deduced from the current conservation law, we derive unconventional boundary conditions characterizing the grain boundary physics and analyze their implications on the transport properties of the system. Angle resolved quantities, such as the transmission probability, are studied within the scattering matrix approach. The conditions for the existence of preferential transmission directions are studied in relation with the grain boundary properties. The proposed theory provides a phenomenological model to study grain boundary physics within the scattering approach and represents per se an important enrichment of the scattering theory of graphene. Moreover, the outcomes of the theory can contribute in understanding and limiting detrimental effects of graphene grain boundaries also providing a benchmark for more elaborated techniques.

Bread wheat (Triticum aestivum L.) is staple of Pakistani people. However, its yield at farmer field is low as compared with its genetic potential. Integration of various crop and soil management strategies might be an option to enhance wheat productivity at farmer field. This 2-year experiment was conducted to check the influence of combine application of natural plant water extracts and biochar on the productvity of wheat during the winter season of 2015-16. The experiment consisted of seven treatment viz. (1) control (2) application of biochar (0.18 kg pot-1) alone, (3) application of sorghum water extract (SWE) alone, (4) application of moringa water extract (MWE) alone, (5) application of biochar + SWE, (6) application of biochar + MWE, (7) application of biochar + SWE+MWE. The results revealed that application of both crop water extracts in combination with biochar improved the growth and grain yield of wheat. Use of MWE in combination with biochar enhanced the grain weight, grain number and grain yield of wheat by 44, 14, and 24%, respectively than the control treatment. In crux, use of MWE in combination with biochar might be a viable option to improve the productivity of bread wheat.

Cadmium accumulation in rice grain poses a serious threat to people’s health. Understanding the genetic basis on grain cadmium accumulation facilitates efforts to reduce it. Here, we show that OsCd1 is involved in Cd uptake and contributes to grain accumulation in rice. Natural variation in OsCd1 with a missense mutation Val449Asp is responsible for the divergence of rice grain cadmium accumulation between japonica and indica. Notably, near-isogenic line tests confirmed that the indica variety carrying the OsCd1^V449 allele could reduce the grain cadmium accumulation. The favorable allele OsCd1^V449 may be an important genetic resource to reduce grain cadmium accumulation for indica.

Scientists, politicians, and practitioners are debating the current structure of pig farms in Lithuania, as medium and small farms have almost disappeared over the past decade. The debated problem is whether the revitalization of medium and small pig farms would sustainably contribute to self-sufficiency in pork? Therefore, this research aims to determine which farms in terms of size could be the most perspective. In order to achieve this aim the multi-criteria evaluation method TOPSIS was used. The economic, production and environmental indicators of Lithuanian pig farms and pig farming sector in Lithuania and selected EU countries: Latvia, Estonia, Poland, Germany, and Denmark were analyzed in this research. The multi-criteria evaluation led to the conclusion that Danish pig farms were the best managed. Germany occupied the second place. The industrial large farms were found as dominated in those countries. Large pig farms (approximately two thousand sows) appeared most perspective in Lithuania: they took the first place in the years examined (2016–2021). The criterion estimate of their assessed indicators was much higher than of the medium (100 sows) and small (20 sows) farms. The main reasons: significantly higher labour productivity, lower cost, lower price, and better production indicators.

(1) Background: Stunting remains a challenge in Indonesia, where 30.8% of under-five children are stunted and may never reach full potential height and cognitive function. We aimed to investigate the risk factors of stunting in Nangapanda subdistrict, East Nusa Tenggara; (2) Methods: The design was cross-sectional study located in rural area as part of PINTERMIDI UI project. We collected quantitative data on social determinants, weight, height, hemoglobin, ferritin, serum zinc, CRP, worm infection, history of deworming, co-morbidity, food security, and nutrient intake; (3) Results: A total of 196 under-five children included and 74% households were food insecure. The prevalence of stunting was 29.9% in this population (31.8% worm infection, 30.3% iron deficiency, and 28.1% zinc deficiency). Multivariate analysis showed household with 5-8 members (AOR 3.076; 95% CI 1.132 – 8.356) and unsafe drinking water (AOR 1.702; 95% CI 0.825 – 3.512) were significant independent risk factors of stunting after adjusted by child’s gender, father’s occupation, caregiver’s education, monthly expenses, sanitary facilities, and food security status; (4) Conclusions: The number of household members is the only independent risk factor of stunting among children age 24-59 months in rural area of Eastern Indonesia. Development of nutrition sensitive intervention and promotion of family planning are needed in order to increase adequate child’s care and feeding practices in rural area of Eastern Indonesia.

Shark unprovoked attacks consist of fatal and non-fatal cases. Numerous cases have been reported involving shark species from Carcharhinus melanopterus with length of 145.5 cm to half-ton Carcharodon carcharias. Currently there are more (P < 0.05) unprovoked non-fatal cases with the average is 28.46 cases/shark species (95%CI: 3.86-53.1) than unprovoked fatal cases, which the average is 5.12 cases /shark species (95%CI: -0.075-10.3). Hence this paper seeks to select the best shark size model that correlates with the unprovoked fatal and non-fatal cases. The studied sharks consist of 24 shark species with the average length is 268.18 cm (95%CI: 230-306 cm) and the average weight is 225.42 kg (95%CI: 128-323 kg). Based on the model and as described by low values of AIC and the highest values of R² and adjusted R² , shark weight followed by combinations of shark weight and length produced unprovoked fatal and non-fatal cases best models. The model for explaining unprovoked fatal cases is the shark weight with high numbers of cases observed in large size shark (weight⁓fatal cases, AIC = 165.359, R² = 0.72, Adj. R = 0.71). While for non-fatal cases, the best model is also the shark weight (weight⁓non fatal cases, AIC = 246.93, R² = 0.63, Adj. R = 0.59).

In December 2012, DOAJ’s parent company, IS4OA, announced they would introduce new criteria for inclusion in DOAJ [1] and that DOAJ would collect vastly more information from journals as part of the accreditation process – and that journals already included, would need to reapply in order to be kept in the registry. My hypothesis was that the journals removed from DOAJ on May 9th 2016 would chiefly be journals from small publishers (mostly single journal publishers) and that DOAJ journal metadata information would reveal that they were journals with a lower level of publishing competence than those that would remain in the DOAJ. Among indicators of publishing competence could be the use of APCs, permanent article identifiers, journal licenses, article level metadata deposited with DOAJ, archiving policy/solutions and/or having a policy in SHERPA/RoMEO. The analysis shows my concerns to be correct.

The aim of this document is to provide practical guidance on the choice of target difference used in the sample size calculation of a randomised controlled trial (RCT). Guidance is provided with a definitive trial, one that seeks to provide a useful answer, in mind and not those of a more exploratory nature. The term “target difference” is taken throughout to refer to the difference that is used in the sample size calculation (the one that the study formally “targets”). Please see the glossary for definitions and clarification with regards other relevant concepts. In order to address the specification of the target difference, it is appropriate, and to some degree necessary, to touch on related statistical aspects of conducting a sample size calculation. Generally the discussion of other aspects and more technical details is kept to a minimum, with more technical aspects covered in the appendices and referencing of relevant sources provided for further reading.The main body of this guidance assumes a standard RCT design is used; formally, this can be described as a two-arm parallel-group superiority trial. Most RCTs test for superiority of the interventions, that is, whether or not one of the interventions is superior to the other (See Box 1 for a formal definition of superiority, and of the two most common alternative approaches). Some common alternative trial designs are considered in Appendix 3. Additionally, it is assumed in the main body of the text that the conventional (Neyman-Pearson) approach to the sample size calculation of an RCT is being used. Other approaches (Bayesian, precision and value of information) are briefly considered in Appendix 2 with reference to the specification of the target difference.

A Brewer Spent Grain (BSG), the most abundant by-product of the brewing process, is mainly used in animal feed and biogas production. The aim of the present work is BSG valorization by yeast fermentation to produce carotenoids. R. mucilaginosa CBS316 was cultured on BSG syrups, supplemented or not with YE and PEP (s-Fsa and Fsa). The biomass and carotenoid production were optimized in flasks and then scaled-up in bioreactor. In flask tests, the maximum biomass concentration was 5.3 and 6.2 g/L for Fsa and s-Fsa cultures, respectively. The maximum carotenoid production was 833 μg/L in Fsa and 1159 μg/L in s-FSA. Considering that the highest specific productivity value (P 7.16 μg/g*h) was obtained with Fsa syrup, this medium was selected for the process scale-up. In bioreactor tests, the maximum concentrations of biomass (4.29 g/L) and carotenoid (396 ug/L) was reached at 72 hours of fer-mentation, 24 h later than in flask. The total carotenoid produced was 524 and 150 ug in bioreactor and flask cultures, respectively. The carotenoids production by R. mucilaginosa was obtained both in Fsa and s-Fsa syrups. The results confirm the possibility to use the syrup as it is, Fsa, thus limiting the process costs.

The use of nitrogen (N) fertilizers can have detrimental effects on the environment due to nitrate leaching. This study aims to examine the impact of N fertilizer source and application timing on wheat yield and nitrate leaching in various soil textures. A randomized complete block design (RCBD) was employed to conduct the experiment. The treatments consisted of two N fertilizer sources: ammonium nitrate (AN) and urea (NN), applied at three different times throughout the year, with a control treatment. The three application timings were total application before sowing (T₁), total application in spring (T₂), and half the amount before sowing and the other half in spring (T₃). The experiment was conducted in three different soil textures (sandy loam, silty clay loam, and silty clay), with three replications over three growing seasons: 2018-19 (Y₁), 2019-20 (Y₂), and 2020-21 (Y₃). The results indicated significant effects of different soil textures on grain yield. Specifically, the silty clay loam soil differed significantly from the sandy loam and silty clay soils in terms of grain yield. The interaction effects between the N fertilizer source and application timing were also found to be significant for all soil textures (p<0.01). In sandy loam and silty clay soils, the grain yield increased when using the T₃ application timing compared to the silty clay loam soil. Notably, the silty clay loam soil with the T₂ application timing exhibited the highest grain yield, with a yield of 6863.6 kg ha^-1. Furthermore, the study revealed that N fertilizers and their application timing significantly influenced the protein content in the silty clay and sandy loam soils. The protein percentages were 10.76 and 10.93 for the silty clay and sandy loam soils, respectively, following the T₂ treatment. Additionally, ammonium nitrate (AN) demonstrated a noticeable effect on the percentage of grain protein compared to urea (NN). In conclusion, the application timing of N fertilizers had an impact on grain yield and protein content in different soil textures. Moreover, nitrate concentration increased throughout the experiment, with the highest soil nitrate concentration observed in both fertilizer treatments, particularly in the sandy loam soil.

High-quality rice (Oryza sativa L.) is increasingly widely planted in China with the improvement of people's living standards and the achievement of rice breeding efforts in recent years. However, the agronomic and physiological performances of high-quality indica rice (HQIR) under different nitrogen(N) application conditions in southern China are little known. Two-year consecutive field experiments were conducted with two HQIR and two ordinary-quality indica rice (OQIR) varieties under moderate and high N application rates, with yield and yield components, biomass, N up-take, and their related traits investigated. We found that grain yields of HQIR were slightly de-creased, but grain yields of OQIR were significantly increased by 6.60%-8.88% under high N rate compared with moderate N rate in both years. Thereby, OQIR produced 8.34%-11.87% and 22.00%-22.50% higher grain yield than HQIR under moderate and high N rates, respectively. The different responses of grain yield to N application rates were mainly due to decreased grain set-ting rate in HQIR and increased spikelets m-2 in OQIR under high N rate. Furthermore, high N rate significantly reduced pre-anthesis AE and improved grain-leaf area ratio, while did not in-crease post-anthesis DM compared with moderate N rate in HQIR, which might result in carbon metabolic deterioration and imbalance of source-sink relationship and subsequently lower supply of carbohydrate to panicle. Our results suggest that a moderate N rate (165 kg N ha-1) is beneficial for HQIR varieties to balance the maximum grain yield and high quality in southern China

Threshing device is the core component of grain combine harvester, and its working performance determines the working quality and production efficiency of the harvester to a great extent. The straw guide plate plays an important role in the threshing device to dredge the threshing matter and control the threshing time of the combine harvester matter in the threshing chamber. In the past, the guiding structure of threshing device could not optimize the working performance of the machine by adjusting the spiral angle, that is, most cereal combine harvester may not be fed smoothly or even clogged when operating under different crop types, yield differences and operating environments, a kind of threshing device with adjustable guide straw board was studied. In this study, the movement model of the straw on the straw guide plate was analyzed, and it was found that the spiral angle “α”of the straw guide was 0<α<58°.Three-factor and three-level response surface method was used to carry out field experiment on drum speed, working speed and guide grass plate spiral angle, and the experimental data were analyzed by quadratic polynomial regression.The results show that the drum speed, working speed and the spiral angle of the guide grass plate have significant effects on the loss rate (PLR) , impurity content (PIR) and breakage rate (PBR) , the drum speed and working speed have an interactive effect on the impurity ratio (PIR) , and the working speed and the helical angle of the guide grass plate have an interactive effect on the loss ratio (PLR) and breakage ratio (PBR) , there is an interaction between the rotary speed of the roller and the helical angle of the guide grass plate on the crushing rate (PBR) .Further optimization analysis showed that the predicted value was PLR = 1.18% , PIR = 0.72% , PBR = 0.53% , the experimental verification value was PLR = 1.26% , PIR = 0.73% , PBR = 0.61% . The absolute error between the experimental value and the predicted value was very small, however, the optimized field test verified value decreased by 8.31% , 50.04% and 60.30% respectively, which indicated that the optimized harvester had better operation quality, in particular, PIR, PBR and other two indicators have a greater increase in the effect.

The research was undertaken to study the way deformation behaves in ultrafine-grained (UFG) conducting Al-Zr alloys doped with Sc, Hf, and Yb. All in all, 8 alloys were studied with zirconium partially replaced by Sc, Hf, and/or Yb. Doping elements (X = Zr, Sc, Hf, Yb) in the alloys total 0.4 wt.%. The choice of doping elements is conditioned by possible precipitation of Al3X particles with L12 structure while annealing these alloys. Such particles provide higher thermal stability of a nonequilibrium UFG microstructure. Initial coarse-grained samples were obtained by induction casting. The UFG microstructure in the alloys was formed by Equal Channel Angular Pressing (ECAP) at 225°C. Superplasticity tests were carried out at temperatures ranging from 300 to 500 °C and strain rates varying between 3.310-4 and 3.310-1 s-1. The highest values of elongation to failure are observed in Sc-doped alloys. A UFG Al-0.2%Zr-0.1%Sc-0.1%Hf alloy has maximum ductility: at 450 °C and a strain rate of 3.310-3 s-1, relative elongation to failure reaches 765%. At the onset of superplasticity, stress–strain curves are characterized by a stage of homogeneous strain and a long stage of localized plastic flow. The dependence of homogeneous strain (eq) on test temperature in UFG Sc-doped alloys is increasing uniformly, which is not the case for other UFG alloys with eq(T) dependence peaking at 350-400 оС. Strain rate sensitivity coefficient of flow stress m is small and does not exceed 0.26-0.3 at 400-500 °C. In UFG alloys containing no scandium, m coefficient is observed to go down to 0.12-0.18 at 500 оС. It has been suggested that lower m values are driven by intensive grain growth and pore formation in large Al3X particles, which develop specifically at the ingot crystallization stage.

In the Global North, there is an increasing interest in pulses both for their beneficial effects in cropping systems and for human health. However, despite these advantages, the acreage dedi-cated to pulses has been declining and their diversity reduced, particularly in European temperate regions, due to several social and economic factors. This decline has stimulated a political debate in the EU on the development of plant proteins. By contrast, in the Global South, a large panel of minor pulses is still cropped in regional patterns of production and consumption. The aim of this paper is to investigate the for cultivation of potential minor pulses in European temperate regions as a complement to common pulses. Our assumption is that some of these crops could adapt to different pedo-climatic conditions, given their physiological adaptation capacity, and that these pulses might be of interest for the development of innovative local food chains in an EU policy context targeting protein autonomy. The research is based on a systematic review of 269 papers retrieved in the Scopus database (1974–2019), which allowed us to identify 41 pulses as candidate species with a protein content higher than 20% that are already consumed as food. For each spe-cies, the main agronomic (e.g. temperature or water requirements) and nutritional characteristics (e.g. proteins or antinutritional contents) were identified in their growing regions. Following their agronomic characteristics, the candidate crops were confronted with variability in the annual growing conditions for spring crops in European temperate areas to determine the earliest poten-tial sowing and latest harvest dates. Subsequently, the potential sum of temperatures was calcu-lated with the Agri4cast database to establish the potential climatic suitability. For the first time, 21 minor pulses were selected to be grown in these temperate areas and appear worthy of inves-tigation in terms of yield potential, nutritional characteristics or best management practices.

Plant height is significantly correlated with grain traits, which is a component of wheat yield. The purpose of this study is to investigate the main QTLs that control plant height and grain-related traits in multiple environments. In this study, we constructed a high-density genetic linkage map using the Wheat50K SNP Array to map quantitative trait loci (QTLs) for these traits in 198 recombinant inbred lines (RILs). The two ends of the chromosome were identified as re-combination-rich areas in all chromosomes except chromosome 1B. The middle area of the chro-mosomes was identified as the recombination-barren area. Both the genetic map and the physical map showed a significant correlation when p=0.001, with a correlation coefficient between 0.63 and 0.99. However, there was almost no recombination between 1RS and 1BS. In terms of plant height, 1RS contributed to the reduction of plant height by 3.43cm. In terms of grain length, 1RS contributed to the elongation of grain by 0.11mm. A total of 43 QTLs were identified, including 8 QTLs for Plant height(PH), 11 QTLs thousand grain weight(TGW), 15 QTLs for grain length(GL),and 9 QTLs for grain width(GW), which explained 1.36%–33.08% of the phenotypic variation. Seven were environment-stable QTLs, including two loci Qph.nwafu-4B and Qph.nwafu-4D that determined plant height. The explanation rates of phenotypic variation were 7.39%-12.26% and 20.11%-27.08%, respectively. One QTL, Qtgw.nwafu-4B, which influenced TGW, showed an explanation rate of 3.43%-6.85% for phenotypic variation, two co-segregating KASP markers were developed, the physical locations corresponding to KASP_AX-109316968 and KASP_AX-109519968 were 25.888344 MB and 25.847691 MB. Another QTL, Qgw.nwafu-4D, which determined grain width, had an explanation rate of 3.43%-6.85%. Three loci that affected the grain length were Qgl.nwafu-5A, Qgl.nwafu-5D.2 and Qgl.nwafu-6B, illustrating the explana-tion rates of phenotypic variation as 6.72%-9.59%, 5.62%-7.75%, and 6.68%-10.73%, respectively. Two QTL clusters were identified on chromosomes 4B and 4D.

The study was carried out to determine the influence of organic and inorganic fertilizers on maize yield and soil fertility; to determine economically optimum organic and inorganic fertilizer combinations for maize production. The study was performed in a randomized complete block design consisting of 10 treatments and 3 replications. The treatments were: Control, 100% of R-NP (138 N and 92 P), 100% of vermicompost,100% of conventional compost, 25% R-NP +75% of vermicompost, 50% of R-NP + 50% of vermicompost, 75% of R-NP+25% of from vermicompost, 25% of R-NP +75% of conventional compost, 50% of R-NP+50% of conventional-compost, 75% of R-NP +25% of conventional-compost. All rates of vermicompost and conventional compost were applied based on N equivalence. Results indicate that applications of inorganic fertilizers with a combination of organic source fertilizers were increases maize yield and yield components and improves the nutrient status of the soil. The highest maize grain yield (7494.3 kg ha-1) and above-ground biomass yield (18718.0 kg ha-1) were obtained from the applications of 50% recommended NP fertilizer plus 50% vermicompost which is based on the recommended N equivalent respectively. Similarly, we found that a combination of both inorganic and organic fertilizers application also is the best strategy to improve major soil nutrients, maintain soil fertility. The economic analysis revealed that the highest net benefit of (108,872.0 ETB ha-1) was obtained from the application of 50% recommended NP fertilizer plus 50% vermicompost based on the recommended N equivalence. Yet, the lowest yield and net benefit value were attained from the control or unfertilized plot. Therefore, this study suggests that an appropriate proportion of organic fertilizer with inorganic fertilizer not only for higher yield maize production with an assurance of potential economic returns to the small hold farmers but also improve and maintain the soil fertility and should be adopted with similar soil type and agro-ecologies.

Bread wheat (Triticum aestivum L.) is one of the most important cereal crops for food security. Of all the stresses that curtail wheat productivity, drought has the most detrimental effects. Especially terminal drought stress i.e. at the time of flowering imposes a big challenge to sustain grain production. In the current study, 339 pre-breeding lines derived from three-way crosses of exotics x elite lines were evaluated in the irrigated and drought stress environments at Obregon, Mexico for the year 2016 and 2018. Drought significantly reduced yield (Y), spike length (SL), number of grains per spikes (NGS) and thousand kernel weight (TKW) by 46.4, 19.2, 23.5 and 25.9%, respectively in comparison to irrigated conditions. Kernel abortion (KA), highly correlated with Y, increased significantly (11.6%) under drought stress environment. Population structure analysis in this panel revealed three sub-populations and a genome wide linkage disequilibrium (LD) decay was at 2.5 cM. Single marker and haplotypes-based genome wide association study (GWAS) revealed significant associations on three chromosomes; 4A (HB10.7), 2D (HB6.10) and 3B (HB8.12) with Y, SL and TKW, respectively. Likewise, associations on chromosomes 6B (HB17.1) and 3A (HB7.11) were identified for NGS and on 3A (HB7.12) for KA. Five traits i.e. normalized difference vegetation index (NDVI), canopy temperature depression (CTD) days to heading (DTH), NGS, KA were associated at chromosome 3A both under irrigated and drought conditions however, different haplotypes were estimated. Twenty-six SNPs were part of 10 haplotype blocks associated with Y, SL, TKW, NGS and KA. In silico analysis of the associated SNPs/haplotypes showed hits with candidate genes known to confer abiotic stress resistance in model species and crops. Potential candidate genes include those coding for sulfite exporter TauE/SafE family in Arabidopsis thaliana, TBC domain containing protein in Oryza sativa subsp. Japonica and heat shock proteins in Aegilops tauschii subsp. tauschii were revealed. The SNPs linked to the promising genes identified in the study can be used for marker-assisted selection.

Hot rolling tests of a low-alloy steel were conducted at a rolling temperature of 850 ℃ under different lubrication conditions, including benchmarks (dry condition and water) and water-based nanolubricants containing different concentrations of nano-TiO₂ from 1.0 to 8.0 wt%. The effects of nanolubricants on rolling force, surface roughness, thickness of oxide scale and microstructure were systematically investigated through varying nano-TiO₂ concentrations. The results show that the application of nanolubricants can decrease the rolling force, surface roughness and oxide scale thickness of rolled steels, and refine ferrite grains. In particular, the nanolubricant containing an optimal concentration (4.0 wt%) of nano-TiO₂ demonstrates the best lubrication performance, owing to the synergistic effect of lubricating film, rolling, polishing and mending generated by nano-TiO₂.

Sunn pest is one of the most crucial noxious species in agriculture. As the sunn pest penetrates and makes damage to the grains, they can no longer be utilized to make bakery goods like bread, pasta, and other baked foods since they become unusable. Therefore, analysis and detection of damaged wheat grains are necessary for production to continue. We recommend that the dataset could be used for analysis and segmentation of the wheat grains, detection of the sunn pest damage condition, and classification of the 6 species of which the dataset consists. As mentioned, in our dataset, there are 6 different species of wheat, including Bezostaja, Müfitbey, Nacibey, Sönmez-2001, Tosunbey, and Ekiz, which are the species that were made in Türkiye. Our dataset differs from the others due to its various species and the condition, whether it is healthy or sunn pest damaged or broken wheat grain, and because the dataset is a multiclass one, it can be used for the classification of the varieties. On the other hand, when the sunn pest damage condition is taken into account, the dataset is suitable for the detection of the sunn pest damage. In addition to that, the dataset includes grains that touch each other which makes it more applicable to problems that arise in real-life. The dataset consists of 83 sunn pest damaged and 87 healthy wheat images. In addition, there are 170 images that contain 3565 wheat grains. As can be observed, the dataset contains a variety of wheat species with sunn pest affected which displays that the promised dataset is suitable for numerous machine learning problems such as classification, segmentation, and detection.

Inbreeding depression is expected to be more pronounced in fitness-related traits, such as pig litter size. Recent studies have suggested that the genetic determinism of inbreeding depression may be heterogeneous across the genome. Therefore, the objective of this study is to conduct a genomic scan across the pig autosomal genome to detect the genomic regions that control inbreeding depression for litter size in two varieties of Iberian pigs (Entrepelado and Retinto). The datasets consist of 2,069 (338 sows) and 2,028 (327 sows) records for litter size (Total Number Born and Number Born Alive) for the Entrepelado and Retinto varieties. All sows were genotyped using the Geneseek GGP PorcineHD 70 K. We employed the Unfavorable Haplotype Finder software to extract runs of homozygosity (ROHs) and conducted a mixed model analysis to identify highly significant differences between homozygous and heterozygous sows for each specific ROH. A total of 8 genomic regions located on SSC2, SSC5, SSC7, SSC8, and SSC13, were significantly associated with inbreeding depression, housing some relevant genes such as FSHR, LHCGR, CORIN, AQP6, and CEP120.

Polyaniline or PANI is a conductive polymer (CPs) with flexibility in turning into conducting properties. The drawback is mainly in terms of limited mechanical properties improvement which attracted the interest in fabrication of PANI with other polymeric materials. PANI-PVL composites film was synthesized and fabricated in this work with chronological steps according to the objectives aligned in two different phases. The first phase determines the optimum parameters to synthesize nanosized PANI. The ideal initial molar ratio, r was 1, stirring speed of 600 rpm, purified by filtration, synthesis temperature of 25 oC, washed by dopant acid, acetone and distilled water. The usage of non-ionic surfactant, Triton X-100 (TX100) with 0.1 % concentration favours the formation of smaller particle size of PANI and good dispersibility compared to the usage of anionic sodium dodecyl sulphate (SDS). The synthesis of PANI in nanosized dimension has the potential to be applied for antimicrobial applications such as gloves and antimicrobial coating of frequent contact points in the near future.

Abstract: Ovulation failure was associated with a reduction in pre-mating concentrations of oestradiol-17β and prolactin (PRL). The present study aimed to evaluate whether pre-mating PRL levels have a role on the reproductive efficiency of doe rabbits. A total of 78 multiparous California does (2nd parity) were divided, according to plasma pre-mating PRL, into five categories, >20-25, >25-30, >30-35, >35-40, and >40-45 ng/ml. Does in all categories were naturally mated and kindled, then their reproductive measurements and progesterone (P4) levels were determined. Results show that pre-mating PRL averaged 23.60±0.78, 28.00±0.83, 33.46±0.43, 38.17±0.49 and 41.98±0.68 ng/ml in five categories (p < 0.05), respectively, representing the highest distribution (38.5%) in the 3rd-category. Live body weight of doe rabbits, at mating, pregnancy, and parturition increased (p < 0.05) with increasing pre-mating PRL level. The number of services, litter size, and pregnancy rate increased (p < 0.05) by increasing PRL levels. Reproductive traits and P4 level at mid-pregnancy of does, and average weight of kits at birth increased (p < 0.05) by increasing PRL levels. The pre-mating PRL profile is important for the identification of reproductive performance in doe rabbits.

Meganthropus palaeojavanicus was known very tall with body height of 8 feet and this made M. palaeojavanicus as the tallest hominid ever existed. This species was living in closed tropical woodland and hilly landscape as the fossil remains were found in a remote forest in Sangiran, central Java. Owing large body size, it may influence the foraging ecology of M. palaeojavanicus to cope with the terrain. In here, this study aimed to model the M. palaeojavanicus foraging ecology along terrain gradients. The model indicates that within 5 km home range radius, the most suitable foraging areas were in north east since these areas have more flat landscapes with slopes of <7.5%. While less suitable areas in north west and south west areas were characterized by hilly landscapes with rugged terrain and steep slopes with slopes of >62.8%.

The purpose of this paper is to analyze how Green Business Models (BMs) established by small and medium enterprises (SMEs) can incorporate product and process decarbonization in their components (value proposition, creation and capture) and to what extent this incorporation is affected by SME size. We use a database comprising 1,161 observations of SMEs, 466 in 2014 and 695 in 2016. The results show that SMEs’ value propositions give an intermediate valuation to both legally required and voluntary reduction of environmental impact, irrespective of SME size and the year analyzed. Regarding value creation, SMEs adopt practically no environmental practices, and there are significant differences according to size, with more difficulties than advantages stemming from small size. The study also shows that such environmental practices are not effective in reducing carbon. This diagnosis indicates that SMEs need help from the administration if they are to play a key role in the process of transformation toward a low-carbon economy. Legislative actions involving harsher environmental protection measures might help shape value propositions that place greater importance on reducing environmental impact, whereas training actions on available environmental techniques, promotion of research on how to adapt such techniques to SMEs and the development of specific practices for SMEs might enhance environmental value creation and capture in their BMs.

A picture is a powerful and convenient medium for inducing the illusion that one perceives a real three-dimensional scene. The relative invariance of picture perception across viewing positions has aroused the interest of painters, photographers and visual scientists. Many studies have been devoted to perceptual invariance when pictures are viewed from oblique directions. Invariance across viewing distances has received less attention. This study presents a computational analysis of pictures of perspective scenes taken from different distances between camera and physical objects. Distances and directions of pictorial objects were computed as function of viewing distance to the picture and compared with distances and directions of the physical objects as function of camera position. The computations show that pictorial distance and direction are determined by angular size of the depicted objects. Pictorial distance and direction are independent of camera position, focal length of the lens, and picture size. Ratios of pictorial distances, directions and sizes are constant as function of viewing distance. The constant ratios are proposed as the reason for invariance of picture perception over a range of viewing distances. Reanalysis of distance judgments obtained from the literature shows that perspective space, previously proposed as the model for visual space, is also a good model for pictorial space. The geometry of pictorial space contradicts some conceptions about picture perception.

This research program investigated the effects of layer thickness (50 and 100 microns) on the microstructure and mechanical properties of electron beam powder bed fusion (EBPBF) additive manufacturing of Inconel 625 alloy. The as-built 50 and 100 micron layer thickness components were also heat treated at temperatures above 1100 oC, which produced a recrystallized grain structure containing annealing twins in the 50 micron layer thickness components, and a duplex grain structure consisting of islands of very small equiaxed grains dispersed in a recrystallized, large-grain structure containing annealing twins. The heat treated component microstructures and mechanical properties were compared with the as-built components in both the build direction (vertical) and perpendicular (horizontal) to the build direction. Vickers microindentation hardness (HV) values for the vertical and horizontal geometries averaged 227 and 220 for the as-built 50 and 100 micron layer components, and 185 and 282 for the corresponding heat treated components. The yield stress values were 387 MPa and 365 MPa for the as-built layer horizontal and vertical 50 micron layer geometries, and 330 MPa and 340 MPa for the as-built 100 micron layer components. For the heat treated 50 micron components, the yield stress values were 340 and 321 MPa for the horizontal and vertical geometries, and 581 and 489 MPa for the 100 micron layer components, respectively. The elongation for the 100 micron layer as-built horizontal components was 28% in contrast to 65% for the corresponding 100 micron heat treated layer components, an increase of 132% for the duplex grain structure. However, the coarse grains containing annealing twins and the equiaxed small grain islands in the duplex structure for the heat treated components contained continuous carbides in the grain boundaries, and this may indicate sensitization and a reduction in corrosion resistance. These findings point to the potential mechanical property advantage for heat treatment of Inconel 625 alloy 100 micron layer thickness components fabricated by EBPBF.

: The crystallization conditions from the solution play an important role in determining the mor-phology, phase composition, and photovoltaic properties of perovskite films. Post-processing of the obtained films can have a crucial role in increasing the grain size of perovskite and enhancing its crystallinity. It has been shown that the formation of crystal nuclei can be utilized to accelerate crystallization. In this case, crystallization occurs through the growth of seed crystals created in the solution, enabling the formation of relatively large crystals. For the deposition of CH3NH3PbI3 hybrid halide perovskite films from a solution of the perovskite in dimethylformamide the spin coating technique was employed. Pre-crystallization was achieved by annealing the films at a temperature of 100 or 110 °C. The dissolution process involved adding a drop of dimethylformamide onto the substrate surface and allowing it to partially dissolve the perovskite film. Subsequently, residual solvent was removed through spin coating. The mor-phological analysis of the perovskite film surface after recrystallization at temperatures ranging from 80 to 130 °C was performed. The infrared transmission spectra of the obtained perovskite films were investigated, and their light absorption characteristics were studied through transmission spectra. The perovskite structure in the obtained films was confirmed by the peaks observed in the X-ray diffraction patterns.

Abstract: The search for alternative protein sources to soy-bean meal (SBM) in animal feeding is a strategic objective to reduce production costs and contribute to a sustainable animal produc-tion. Spirulina, due to the high protein content, has emerged as a potential cost-effective, sus-tainable, viable and high nutritional value food resource for many animal species. Insect larvae (Tenebrio molitor and Hermetia illucens) are also considered potential alternatives to SBM, given their high edible percentage of almost 100%, as well as a protein value higher than that of vegetable proteins. Rapeseed meal and grain legumes, such as faba beans, peas, lupins and chickpea can also be used as locally producible protein ingredients. This study reviews the nutritional value of these potential alternatives to SBM in pig diets, effects on animal perfor-mance, digestion, immune system, physicochemical and sensorial characteristics of meat, in-cluding processed meat products of pork. Limits on their use in pig feeding are also reviewed to indicate gaps to be filled in future research on the supplementation level of these potential al-ternative protein sources into pig diets.

The crystallization conditions from the solution play an important role in determining the mor-phology, phase composition, and photovoltaic properties of perovskite films. Post-processing of the obtained films can have a crucial role in increasing the grain size of perovskite and enhancing its crystallinity. It has been shown that the formation of crystal nuclei can be utilized to accelerate crystallization. In this case, crystallization occurs through the growth of seed crystals created in the solution, enabling the formation of relatively large crystals. For the deposition of CH3NH3PbI3 hybrid halide perovskite films from a solution of the perovskite in dimethylformamide the spin coating echnique was employed. Pre-crystallization was achieved by heating films at a temperature of 100 or 110 °C. The dissolution process involved adding a drop of dimethylformamide onto the substrate surface and allowing it to partially dis-solve the perovskite for 30-40 seconds. Subsequently, residual solvent was removed through spin coating. The recrystallization process was carried out by heating films at the temperature range of 80 to 130 °C. The morphological analysis of the perovskite film surfaces after recrystallization at tem-peratures ranging from 80 to 130 °C was performed. The infrared transmission spectra of the obtained perovskite films were investigated, and their light absorption characteristics were studied through transmission spectra. The perovskite structure in the obtained films was con-firmed by the peaks observed in the X-ray diffraction patterns.

Global warming causes an alarming increase in temperature which negatively affects growth, physiology, and yield of rice. To gain some insights into the impacts of booting HT (at 42°C, 3 h for 7 days), we investigated its effect in three rice genotypes, namely, N22, KDML105 and IR64. Booting HT caused an extended phenology and lower photosynthesis and plant growth rate but an increase in chalkiness. Although, prolonged phenology from dough to physiological maturity led to longer duration of grain filling, the negative effects of its was significantly lower yield components, yield and harvest index in all rice. Among cultivars, N22 presented adapted ability to maintain leaf gas exchange and compensated vegetative part by an increase in tiller numbers resulting in less affected growth rate. It prolonged phenology that caused extended grain filling. Consequence, N22 was the lowest reduction in number of seed panicle^–1, number of filled seeds hill^–1, yield, HI as well as the lowest percentage chalkiness. KDML105 adapted to booting HT by maintaining leaf gas exchange, increasing specific leaf area and prolonging phenology. The longest extended phenology together with the maintenance of high photosynthesis during dough grain were associated with moderate yield reduction and chalkiness. However, IR64 showed dramatic reductions in photosynthesis, growth rate, and yield but highest percentage grain chalkiness. Therefore, in response to booting HT, N22, KDML105 and IR64 could be indicated as being heat tolerant, moderately heat sensitive, and heat sensitive, respectively. This can be applied for crop modelling and rice heat tolerance in breeding program.

Grain yield prediction affects policy making in various aspects such as agricultural production planning, food security assurance, and adjustment of foreign trade. Accurately predicting grain yield is of great significance in ensuring global food security. This paper is based on the MODIS remote sensing image data products from 2010 to 2020, and adds band information such as vegetation index and temperature to form composite remote sensing data as a data set. Aiming at the lack of models for large-scale forecasting and the need for human intervention in traditional models, this paper proposes a grain production estimation model based on deep learning. First, image cropping and yield mapping techniques are used to process the data to generate training samples. Then the channel and spatial attention mechanism (Convolutional Block Attention Module, CBAM) is added for extracting spatial information in different remote sensing bands to improve the efficiency of the model. Long Short-Term Memory (LSTM) neural networks is also added to obtain feature information in the time dimension. Finally, a national-scale grain yield prediction model is constructed. The proposed model was tested on data from 2018 to 2020 showing an average R2 of 0.940 and an average RMSE of 80,020 tons, indicating that it can predict Chinese grain yield better. The model proposed in this paper extracts grain yield information directly from the composite remote sensing data, and solves the problem of small-scale research and imprecise yield prediction in an end-to-end manner.

The grain-to-grain stress vertically in sediments is given by the overburden less the pore fluid pressure, σ, divided by the fraction of the horizontal area which is the supporting matrix , (1 − φ), where φ is the porosity. It is proposed that the fractional reduction of this ratio, Λ, with time is given by the product of φ 4m/3 , (1 − φ) 4n/3 , and one or more Arrhenius functions A exp(−E/RT ) with m and n close to 1. This proposal is tested for shale sections in six wells from around the world for which porosity-depth data are available. Good agreement is obtained above 30-40 C and porosities less than 0.5. Single activation energies for each well are obtained in the range 15-33 kJ/mole, close to pressure solution of quartz, 24 kJ/mol. Values of m and n are in the range 1 to 0.8, indicating nearly fractal pore-matrix spaces and water-wet interfaces. Results are independent of over- or under-pressure of pore water. This model explains shale compaction quantitatively. Given porosity-depth data and accurate activation energy, E, one can infer paleo-geothermal-gradient and from that organic maturity, thus avoiding unnecessary drilling.

The aim of the present study was to assess the efficacy of All Cosmos Industries (ACI) bio-organic and bio-chemical fertilizers and ACI N-Fixer (N-Bio Booster) on the paddy yields based on the field trial plots at Langkat, Medan, Indonesia. This application of ACI bio-organic fertilizer (NPK 5/5/5) and ACI bio-chemical (NPK 15/15/15) fertilizer and ACI N-Fixer tests were conducted at the paddy farm at Langkat from May-October 2018. This study employed a factorial randomized complete block design which consisted of two factors, namely: Factor I with four types of fertilizers while Factor II consisted of two paddy varieties (Inpari 30 and Inpari 32). Overall, the filled grains in the ACI treatments are significantly (P< 0.05) higher than those in the control treatments that used Normal Chemical Compound NPK. Overall, total weight per meter² (368-617g) in ACI treatments are also significantly (P< 0.05) higher than those (319-371g) in the control treatments. At harvesting time at 105 days after transplanting, significantly higher (P< 0.05) colony counts (13-15 x 10⁶ CFU/mL) (for ACI treatments), than those (8 x 10⁶ CFU/mL) in the controls positively indicated higher total yields of paddy grains per hectare. It was found that the application of ACI bio-organic and bio-chemical fertilizers and ACI N-Fixer can improve paddy yields of the two rice varieties, between 16.4-38.2% (up to 5.75 MT/ha), in the field trial plots at Langkat. These commercial fertilizers play an imperative role in refining the soil fertility and thereby can increase the yield of rice production. Therefore, it is highly recommended that ACI bio-organic and ACI bio-chemical fertilizers and ACI N-Fixer (N-Bio Booster) can be employed to increase the paddy yield in this region.

The mechanical hill wet-seeded rice machine is benefits to establish uniform seedling, and ditches were established by using this machine. However, little knowledge is known on the effect of the establishment of ditches on growth, lodging and yield, and their relationship with root traits. In this study, two field experiments were conducted during 2012 and 2013 with using two super rice varieties (i.e. hybrid rice ‘Peizataifeng’ and inbred rice ‘Yuxiangyouzhan’) grown under three ditches establishment treatments (i.e. T1: both water ditches and seed ditches were established by the machine, T2: seed ditches were established by the machine, T3: neither water nor seed ditches were established by the machine). The lodging index and lodging resistance traits, the grain yield and above-ground dry weight and the root traits were measured. The results showed that the lodging index was significantly affected by the treatments with ditches. The strongest lodging resistance was detected in mechanical hill wet-seeded rice with ditches treatment in both 2012 and 2013. The lodging resistance was strongly related to the breaking resistance, the root volume and root superficial area at the heading stage and maturity stage and the total root length at the heading stage. No significant difference was investigated in grain yield or dry weight of mechanical hill wet-seeded rice. Yuxiangyouzhan showed higher grain yield, dry weight and better lodging resistance but unfavorable root growth attributes than Peizataifeng. Therefore, the mechanical hill wet-seeded rice with ditches treatment increased rice lodging resistance is related to root traits.

This paper presents the results of investigations of the effects of hot deformation parameters in compression investigation on the austenite grain size in HSLA steel (0.16% C, 0.037% Nb, 0.004% Ti, 0.0098% N). The axisymmetric compression investigations were performed on cylindrical investigation specimens of d=1.2 using the Gleeble 3800 simulator. The strain rate=1s^-1÷15.9s^-1 and strain degree ε=1.2. Before deformation, the research specimens were austenitized at TA = 1100 ÷ 1250 °C. Metallographic observations of the primary austenite grains were conducted with an optical microscope, while the structure of dynamically recrystallized austenite, inherited by martensite, was examined by EBSD technique using a scanning electron microscope. Based on the analysis of investigation results, it was found that the size of dynamically recrystallized austenite grains in HSLA steel were clearly affected by hot compression parameters. In contrast, no significant impact of austenitising temperature on their size was found.

Conservation agriculture (CA) could be very effective for agricultural sustainability under Mediterranean environments, where farmers rely on short rotation based on durum wheat. In this work we investigated the effect of different combination of tillage treatments and crop sequence (conventional tillage and wheat monocropping, CT-WW; conventional tillage, and wheat following faba-bean, CT-WF; zero tillage and wheat monocropping, ZT-WW; zero tillage and wheat following faba-bean, ZT-WF) on yield, grain quality traits as well as on diseases incidence and severity in durum wheat (var. Saragolla). The results of a two-years of data of a long-term experiment (7-year experiment; split-plot design) are discussed. The CA approach (ZT+WF), which induced always the highest grain yields (6.1 t ha-1 and 3.3 t ha-1 in 2016 and 2017) thanks to an increased number of spikes m-2 (296 vs 269 and 303 vs 287 spikes m-2 in 2016 and 2017, respectively) as well as to a more pronounced ear length, demonstrated significant positive influences in terms of grain quality. It promoted grain protein accumulation (12.1% for ZT+WF versus 11.4% for ZT+WW and 12.4% for ZT+WF versus 10.6% for ZT+WW in 2016 and 2017), improved gluten quality (in terms of SDS sedimentation test) and colour of the grain. The abundance of crop residues determined a higher incidence and severity of Zymoseptoria tritici leaf symptoms under CA system; nevertheless the late appearance of infection was the main reason of not affecting yield and quality traits. The presence of faba-bean (WF) in the rotation significantly reduced leaf symptoms of Z. tritici.

Sample size using prevalence has been one of the most important medical research methodologies and has been used in original articles more often than any other statistical tool available. The simple formula consists of variables interdependent and it is as important to understand how they influence each other as it is to learn to use the formula to calculate the sample size. With the choice of different amounts of precision and levels of confidence available to a medical researcher, it should be of paramount importance to understand what a slight change in choosing the parameter would mean at the end of the research. Understanding of different Z values, Levels of precision, and ranging Prevalence is required to understand the effect on the sample size and subsequently on the research. Topological representation using parameter ranges can be used to demonstrate this relationship.

This study aimed to investigate the interactions between corn particle size (PS) and conditioning temperature (CT) on the performance, carcass traits, intestinal morphology, and immune responses in broilers fed a corn-soybean meal-based diet. A total of 360, one-day-old male broiler chicks (Ross 308) were randomly allocated into six dietary treatments in a 2×3 factorial arrangement, consisting of two corn PS (finely ground with geometric mean diameter (GMD) of 357 µm (PSF) vs. coarsely ground corn with GMD of 737 µm (PSC), and three CT [unconditioned (CTU), conditioned at 75◦C (CT75) and 90◦C (CT90)]. Birds accommodated in 30 pens with five replicates and 12 chicks per each. There was no interaction between corn PS and CT on growth performance and immune response of broilers at any growth phases. However, during the starter (0-10d) period, the average daily weight gain (ADWG) and feed conversion ratio (FCR) of PSF-fed birds were significantly improved compared to those fed PSC (P<0.05). During the starter (0-10d) and grower (11-24d) periods, increasing the conditioning temperature of corn increased the ADWG, while in the starter phase only the CT75 caused a lower FCR (P<0.05). Broilers fed PSF corn showed lowest FCR during the finisher (25-42d) period compared to those fed PSC (P<0.05). Conditioning corn at 75ºC reduced FCR during the finisher (25-42d) period compared to the birds fed CTU and CT90 corn (P<0.05). In whole experimental periods (1-42d), PSF and CT75 treatment increased the ADWG compared to the PSC and CTU (P<0.05). The CT75 treatment improved primary total anti-sheep red blood cell (SRBCs) titer (IgT) and IgM and secondary IgT and IgG responses compared to the other experimental groups (CTU and CT90) (P<0.05). No significant PS × CT interaction was found on Newcastle disease (ND) antibody titer of broiler chickens (P>0.05). Feeding CT75 corn reduced duodenum and jejunum relative length compared to the birds fed diets containing CTU corn. Significant PS×CT interactions (P<0.05) were observed for villus height, villus height to crypt depth, crypt depth, muscle thickness, and absorption surface area of jejunum. The highest carcass yield observed in PSF-CT75-group (P<0.05). In conclusion, the use of finely ground corn (PSF) conditioned at 75℃ (CT75) was beneficial to growth performance, development of the digestive tract, jejunum histomorphometry and the immune responses of broilers.

Remanufacturing is a way for product recovery initiative and maintaining sufficient production flow to satisfy customer demand through circular economy. Recently, manufacturers have been progressively incorporating remanufacturing processes, making their supply chain vulnerable to disruptions. Among the disruptions that usually occur is the shortage in spare parts supply, which causes unexpected delay in production and possible loss of sales. In the face of potential disruption, it is essential for remanufacturing facilities to manage their supply chains in an optimum manner as to decrease the adverse impact of disruptions to their business. In this study, a two-stage production-inventory system is analysed by developing a cost-minimisation model focusing on the recovery schedule after a disruption occurrence in sourcing spare parts for a remanufacturer’s production cycle. The developed model was solved using the branch and bound algorithm. Through numerical experiments, the results indicate that the optimal recovery schedule and the number of recovery cycles are significantly dependant on disruption time, lost sales and backorder costs. Moreover, a sensitivity analysis shows that the lost sales option seems to be more effective than the backorder option in optimising the system’s overall cost. The proposed model could assist managers in deciding the optimal production strategy while providing interesting managerial insights into vital spare parts recovery issues when disruption strikes.

The orchid market is a dynamic horticultural business in which novelty and beauty command high prices. The development of miniature to large and showy flowers, in addition to fragrance, is mainly of interest. Overall organ size might be modified by doubling the chromosome number, which can be accomplished by careful study of meiotic chromosome disjunction in hybrids or species. Meiosis is the process in which diploid (2n) pollen mother cells recombine their DNA sequences and then undergo two rounds of division to give rise to four haploid (n) cells called sporads. Thus, by interfering in chromosome segregation, one can induce the development of diploid recombinant sporads called dyads. These dyads may be used for breeding polyploid progenies with enhanced fertility and large flower size. This review gives an overview of developments in orchid breeding placed in the large context of ploidy breeding in higher plants to facilitate innovation

The feral mink population in Denmark consists of two groups of animals; mink born in the wild and mink that have recently escaped from farms. The aims of this study are; 1) to estimate the reproduction and mortality of wild-born and captive-born mink and 2) to estimate the age of mink based on the width of pulp cavity (% of tooth width) in the canine teeth. During 2018, 247 wild caught mink were sent for necropsy at the Danish National Veterinary Institute. Of these mink, 112 were determined as captive-born and 96 were determined wild-born. The mean litter size ± SE of wild-born females was 7.6 ± 0.9 (range: 5-11 kits) and for captive-born females 5.9 ± 0.9 (range: 1-10 kits). The best fitting regression line for mink age (in months) based on pulp width was y=0.42x2-11.52x+104.7, R² = 0.77, p&lt; 0.0001. Individuals with a pulp cavity width &lt;35% was found to be younger than one year. The turnover of mink caught in nature was estimated to 66% and the yearly mortality to 69%, therefore the population is slightly declining. In conclusion, a feral reproducing mink population in Denmark persists, besides the continues influx of captive-born mink escaped from farms.

The angular diameter is the angle subtended by a generic object – an apple or a star – to the eye of an observer, and it describes how large the object appears from a given viewpoint. The angular diameter represents a powerful tool for distance calculations starting from a directly measurable information and it finds application in several contexts varying from cosmography to architecture. In this article, the author proposes a novel equation to calculate the apparent diameter of whatever object. This equation defines the relationship between the object’s apparent diameter with respect to the travelled distance starting from the initial distance R₀ at which the observed object is located. Based on the preliminary tests conducted, the model seems to faithfully portray this relation with respect to measured values, also at the astronomical scale, thus considering the Earth-Moon distance, where, the absolute error detected is about 0.56%. Tests highlight also a dependency between the results accuracy and the measurement conditions suggesting a high level of sensibility linked to the initial magnification effect produced by the retina or the artificial lens employed.

Plastics are naturally hydrophobic materials so, in order to employ flotation for the separation of plastic mixtures, the use of appropriate wetting agents is mandatory. In this work, the effect of pretreatment with alkaline solutions of sodium hydroxide on the floatability of four plastics (PET, PS, PMMA and PVC) was studied. The influence of NaOH concentration, treatment time and temperature of the alkaline solution, and influence of particle size was analyzed. Results showed that alkaline treatment had a strong effect on PET floatability, some effect on floatability of PMMA and PVC and no effect on floatability of PS. Plastics floatability decreased with the increase of NaOH concentration, temperature and treatment time of the alkaline solution. Based on flotation behavior of simple plastics, flotation separation after alkaline treatment of bi-component mixtures of PET with PS and PVC was achieved efficiently. The best separation was obtained for PET/PS mixture, a floated with a grade of 98% in PS and a sunk with a grade of 100% in PET. PET/PMMA mixture led to the worst separation. For PET/PMMA and PET/PVC mixtures, flotation separation improved with the decrease of the particles size.

Aim: aim of this study is to evaluate the clinical and radiographic healing after repairing mechanical furcal perforations that occurred in primary molars by using MTA (Mineral Trioxide Aggregate) and search in some factors that may affect the prognosis of the treatment. Materials & Methods: we had 34 primary molars in 32 children aged 5–10 years, were treated by using MTA material after the occurrence of furcal perforation during pulpotomy procedure. Cases had been followed clinically and radiographically within 12 months. Statistical analyses were performed at p-value = 0.05. Results: All teeth were asymptomatic at the first week. Overall success rate was 79.3%. There was no significant statistically differences between overall-success rates according to the perforation size and continues bleeding in the furcation area (p-value > 0.05). Conclusions: Iatrogenic furcal perforations that may occur during pulpotomy in primary molars can be treated successfully by using MTA, and small sized-perforations may have more favorable prognosis than the large ones. Iatrogenic furcal perforations that may occur during pulpotomy in primary molars can be treated successfully by using MTA, and small sized- perforations may have more favorable prognosis than the large ones.