A lead zirconate titanate [PZT;Pb(Zr_0.52Ti_0.48)O₃] layer embedded infrared (IR) detector decorated with wavelength-selective plasmonic crystals has been investigated for high-performance non-dispersive infrared (NDIR) spectroscopy. A plasmonic IR detector with an enhanced IR absorption band has been designed based on numerical simulations, fabricated by conventional microfabrication techniques, and characterized with a broadly tunable quantum cascade laser. The enhanced responsivity of the plasmonic IR detector at specific wavelength band has improved the performance of NDIR spectroscopy and pushed the limit of detection (LOD) by an order of magnitude. In this paper, a 13 fold enhancement in the LOD of a methane gas sensing using NDIR spectroscopy is demonstrated with the plasmonic IR detector.

The physical properties of coal reservoirs are the main restrictions to exploration and development of CBM. The study of the physical characteristics of coal reservoirs and their controlling factors is of great significance to the safe and efficient development and utilization of CBM resources in the mining area. The Pingdingshan No. 10 coal mine was chosen for this study because of its better gas production effect at the test wells. The reservoir properties of the main coal seams of the No. 10 coal mine were tested and analyzed to comprehensively evaluate the reservoir properties. The results indicate that (1) The gas content and methane purity of the No. 4 coal seam are significantly higher than the No. 2 seam, and therefore they have better development potential than the No. 2 seam; (2) The average adsorption time of the No. 2 coal seam is less than that of the No. 4 seam, making it easier to reach the peak production capacity of CBM wells in the short term, but is not conducive to long-term stable production of CBM. The Langmuir volume of the No. 2 coal seam samples was significantly greater than for the No. 4 coal seam; however, the No. 4 coal seam contains about three times the amount of gas in the No. 2 seam; (3) All three coal seams have high porosity, which is favorable for large amounts of CBM adsorption and storage. Micropores predominate, transitional pores are less frequent, and a few mesopores occur; macropores are the least common. Samples from the No. 4 seam contained the highest proportion of micropores; (4) Organic pores were common in the all coal samples, with pore diameters not more than 30 µm, mainly concentrated between 50.5 and 1000 nm. Microfractures with aperture less than 70 nm were relatively frequent, mainly in the 50–65 nm range. A large number of the nanoscale microfractures were curved or jagged; (5) Fractures in the No. 2 and No. 4 coal seam samples with widths of 50 nm to 20 µm were more developed, and many were filled with kaolinite, quartz and other minerals; (6) The samples contained mostly layered silicate minerals (kaolinite), with hard granular minerals (quartz) next, and a very small quantity of iron-type minerals such as siderite and pyrite in dendritic form. The results of this study can provide a reference basis for the large-scale development and utilization of subsequent CBM wells.

The Pingbei area is the main accumulation area of oil and gas in the Xihu Sag. The phase characteristics of oil and gas in this area are complex, and the understanding of their genesis is still unclear. In this paper, based upon discussions of crude oil and natural gas geochemical data, integrated with local geological features, we discuss the sources, migration, and phase state characteristics of oil and gas in the Pingbei area of the Xihu Sag. The study results showed that the crude oil and natural gas in the Pingbei area are coal-derived and the oil and gas produced by the humic organic matter during the maturity stage. The oil and gas source correlation showed that crude oil and natural gas have good affinity with the Eocene Pinghu Formation (PF) coal-bearing source rocks. Crude oil has the characteristics of near-source accumulation and short-distance migration while natural gas is supplied from a dual source: the coal-derived hydrocarbon rocks of PH in the deep part of the study area, supplemented by the coal-derived hydrocarbon rocks of PH on the bottom of the slope, and adjacent hydrocarbon-bearing sub sag. The distribution characteristics and geochemical migration indices of hydrocarbon showed that the oil generated from the hydrocarbon source rocks of PH in the deep Pingbei area mainly migrates vertically along the fault connecting the reservoir and the source rocks to the trap, where it accumulates, while the natural gas exhibits deep and large faults that mainly migrate vertically, supplemented by its lateral migration along the composite transport system composed of faults and sandstone layers in the slope zone. The mechanisms of produced, exhausted, and geochromatographic effects (PGE), as well as evaporative fractionation (EF) and phase-controlled migration fractionation (PMF), result in the obvious discrepancy of hydrocarbon’s properties on the vertical profiles.

Background: Mitigating climate change requires fundamentally redesigned energy systems in which renewable energy sources ultimately replace fossil fuels such as natural gas. In this context, the question how and to which extent the gas sector can contribute to an increasingly climate-neutral future EU energy system is heavily debated among scholars, energy industry experts and policy makers. Methods: We take a two-step approach: We begin with a review of studies from energy industry and academia to discuss potential gas sector contributions from a holistic energy system design point of view; this is followed by a comprehensive discussion of technical potentials, micro-economic conditions and societal implications of renewable gas. We then enrich our findings with the results of an empirical focus group process. Results: The gas sector can not only contribute to balancing volatile renewable energy production but also enable the supply of renewable energy to end-users in gaseous form; based on existing infrastructure. This could reduce costs for society, increase public acceptance and ultimately speed up the energy system transformation. There is the theoretical technical potential to substitute major parts of natural gas with renewable gas of biogenic and synthetic nature. This, however, crucially requires a supportive policy framework like the one established for renewable electricity. Conclusion: Given the societal benefits and the competitiveness of renewable gas as compared to renewable alternatives, energy policy makers should incorporate renewable gas and the existing gas infrastructure in the future energy system framework. The objective should be an optimized interplay of various energy vectors and their infrastructure along the entire energy supply chain. This requires a level playing field for different renewable technologies across different policy areas and a form of public support that strikes the balance between facilitating the gradual substitution of natural gas by renewable gas while maintaining public acceptance for this transformation despite higher costs for end-users.: Given the societal benefits and the competitiveness of renewable gas as compared to renewable alternatives, energy policy makers should incorporate renewable gas and the existing gas infrastructure in the future energy system framework. The objective should be an optimized interplay of various energy vectors and their infrastructure along the entire energy supply chain. This requires a level playing field for different renewable technologies across different policy areas and a form of public support that strikes the balance between facilitating the gradual substitution of natural gas by renewable gas while maintaining public acceptance for this transformation despite higher costs for end-users.

Ni-Al alloys have good corrosion-resistant properties making them preferable as a material of choice compared to ordinary metals. A good understanding of the phase diagram and thermodynamic properties of the Ni-Al alloy binary system is essential in determining relevant industrial applications of the system. The Ni-Al phase diagram is being reassessed since those found in the literatures are based on very old experimental studies. The phase diagram and thermodynamic properties of the Ni-Al alloy is determined using the Thermo-Calc 2022b software over a temperature range of 200 K to 2000 K and 1 atm of pressure. A total of nineteen fields (including elemental Al and Ni) comprising of five single solid phases, one liquid phase, and twelve double regions was obtained from the equilibrium calculation. The thermodynamic calculation has six invariant reactions comprising of two eutectic reactions (914.83 ± 0.025 K and 1641.80 ± 0.025 K), three peritectic reactions (1123.55 ± 0.025 K, 1400.72 ± 0.025 K and 1642.65 ± 0.025 K), and one peritectoid reaction (913.96 ± 0.025 K). The solubility of Al in Ni is also determined. The Thermo-Calc temperature – composition of the Ni-Al alloy is compared with the existing experimental studies to identify the physical properties of the different thermodynamic properties of the Ni-Al alloy binary system.

Aim: Aging is companied by deteriorations of insulin resistance (IR) and insulin secretion. However, little is known about the roles of aging on different phases of insulin secretion (ISEC); i.e., the first- and second-phase of insulin secretion (FPIS, SPIS) and glucose effectiveness (GE). Methods: Totally 169 individuals (43 men and 126 women) with the similar fasting plasma glucose (FPG: 90 mg/dL) and BMI (men: 23 kg/m2, women 22 kg/m2) were enrolled. IR, FPIS, SPIS, and GE were estimated using our previously developed equations shown below. Pearson correlation analysis was conducted to assess the correlations between age and four diabetes factors (DFs: IR, FPIS, SPIS and GE). The equations that are used to calculate the DF in the present study were built and published by our group. Results: The age of the participants ranged from 18- to 78-year-old. Men had higher FPIS but lower HDL-C levels than women (2.067±0.159, 1.950±0.186 μU/min and 1.130±0.306, 1.348±0.357 mmol/dl, accordingly). The results of Pearson correlation revealed that age was negatively related to IR and GE in both genders (IR: r = -0.39, p < 0.001 for men, r = -0.24, p < 0.003 for women; GE: r = 0.66, p < 0.001 for men, r = 0.78, p < 0.001 for women). In the meanwhile, FPIS was also only found to be negatively correlated with age in female (r = -0.238, p = 0.003). But there was no different with SPIS and age in both of genders. Conclusions: We have found that in Chinese with normal FPG level (90 mg/dl) and body mass index (men: 23 kg/m2, women: 22: kg/m2), age is negatively related to IR and GE in both genders. At the same time, only FPIS was found to be negatively related to age in women. The tightness of their relationships, from the highest to the lowest are, GE, FPIS and IR accordingly. The importance of GE should be re-evaluated. These results should be interpreted with caution because of the small sample size.

Quantitative differential phase contrast (qDPC) imaging has become an important method of optical measurement and life science research in microscopy because of its high reconstruction resolution and non-invasive, high-contrast and quantitative imaging of biological samples. Despite the continuous development of the principle and algorithm, the frame rate of the existing qDPC algorithm is still much lower than that of camera acquisition, so it is hardly applied to real-time image the fast-moving biological samples. In this paper, based on color-coded multiplexing strategy, a compact real-time quantitative phase imaging system is designed to realize multi-mode imaging. The system employs a programmable LED array to illuminate directly, and the phase reconstruction algorithm is deployed in the graphics processing unit (GPU) of the laptop to accelerate the calculation. The system can achieve high-speed quantitative phase imaging of non-stained biological samples, and the frame rate can reach 60fps. The device has the advantages of compact structure, low cost and portability. Thus, it is suitable for mobile medical applications.

In the author's opinion, many global problems that face humanity - in the fields of education, medicine, management etc can be tackled more effectively if the cyclic nature of self-reproducing systems – including living beings – is taken into account. Summarizing the main physiological findings of the last decades on "adaptation reactions", one can very roughly say that the way of action which is effective in the sense of productive activity of people happens at the same time to be healthy, and it gives the participants of the process the feeling of happiness. The present paper represents a very short overview of the contemporary concepts of the adaptation reactions based on the fundamental understanding of their cyclic nature due to general properties of self-reproducing systems. One interesting feature of self-reproduction cycles is its first "phase of orientation" which was not discussed in detail in the past but plays a key role in the whole cycle.

The release profiles of methotrexate, an anticancer drug, from the monoolein liquid crystalline cubic phases were studied. The cubic phases were used either in the form of a lipidic film deposited onto a glassy carbon electrode surface or in the dispersed form of magnetocubosomes, which are considered a prospective hybrid drug delivery system. Commonly, cubosomes or liposomes are employed, but not in the case of toxic methotrexate, known to block receptors responsible for folate transport into the cells. The release profiles of the drug from the lipidic films were monitored electrochemically and described using the Higuchi model. They were also modified via changes in temperature; the release was faster, although deviating from the model when the temperature was increased. Magnetocubosomes - cubic phase nanoparticles containing hydrophobic magnetic nanoparticles placed in an alternating magnetic field of low frequency and amplitude, stimulated drug release from the suspension, which was monitored spectroscopically. These new biocompatible hybrid materials are very promising, allowing to control the release of the drug at the appropriate sites, but do require further investigations into their in vitro cytotoxicity and in vivo biodistribution.

A Natural gas is increasingly being sought after as a vital source of energy, given that its production is very cheap and does not cause the same environmental harms that other resources, such as coal combustion, do. Understanding and characterizing the behavior of natural gas is essential in hydrocarbon reservoir engineering, natural gas transport, and process. Natural gas compressibility factor, as a critical parameter, defines the compression and expansion characteristics of natural gas under different conditions. In this study, a simple second-order polynomial model based on the group method of data handling (GMDH) is presented to determine the compressibility factor of different natural gases at different conditions, using corresponding state principles. The accuracy of the model evaluated through graphical and statistical analyses. The results show that the model is capable of predicting natural gas compressibility with an average absolute error of only 2.88%, a root means square of 0.03, and a regression coefficient of 0.92. The performance of the developed model compared to widely known, previously published equations of state (EOSs) and correlations, and the precision of the results demonstrates its superiority over all other correlations and EOSs.

The operation of electricity and natural gas transmission networks in the U.S. are increasingly interdependent, due to the growing number of installations of gas fired generators and the penetration of renewable energy sources. This development suggests the need for closer communication and coordination between gas and power transmission system operators in order to improve the efficiency and reliability of the combined energy system. In this paper, we present a co-simulation platform for examining the interdependence between natural gas and electricity transmission networks based on a direct current unit-commitment and economic dispatch model for the power system and a transient hydraulic gas model for the gas system. We analyze the value of day-ahead coordination of power and natural gas network operations and show the importance of considering gas system constraints when analyzing power systems operation with high penetration of gas generators and renewable energy sources. Results show that day-ahead coordination contributes to a reduction in curtailed gas during high stress periods (e.g., large gas offtake ramps) and a reduction in energy consumption of gas compressor stations.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

We study different aspects of an exactly solvable master equation (ME). Its simplicity allows one direct access to the details of its workings, highlighting significant features and peculiarities. The existence of phase transitions is unveiled.

The temperature-dependent energy storage properties of four tungsten bronze phase compounds are studied together with an investigation of their structure and temperature-dependent permittivity response, i.e., Ba6Ti2Nb8O30 (BTN), Ba6Zr2Nb8O30 (BZN), Sr3TiNb4O15 (STN) and Sr3ZrNb4O15 (SZN) ceramics. It was found that BZN has smaller grains and a more porous structure than BTN. SZN shows no clear grain boundaries with the most porous structure among all samples, exhibiting a much lower permittivity response than other samples with no signs of phase transitions from room temperature to 400 °C. Though the energy storage response of those samples is generally quite low, it exhibits rather good temperature stability. It was suggested that by obtaining a denser structure through chemical modification or other methods, those tungsten bronze ceramics with good temperature stability could be promising as energy storage devices when improved energy storage properties are achieved.

The three-phase separator was perforated after four years’ service. The perforation position is at the bottom of the vessel under the baffle plate in an oil transfer station. The cause of perforation was investigated by chemical analysis using a direct-reading spectrometer, microstructure examined by optical microscope(OM), and lab simulated corrosion experiments by electrochemical workstation, and the corrosion products examined with scanning electron microscopy(SEM), energy dispersive spectrometer(EDS) in this paper. The analyses indicated that the coating at the base of the pressure vessel failed and this led to the direct exposure of the carbon steel plate to the corrosive medium. The electrical contact between the carbon steel and the stainless steel, sets up a galvanic cell that accelerated the corrosion of the pressure vessel which eventually led leads to the perforation.

This article presents a decentralized phase-shedding technique for multiphase converters. The usual central digital controller is replaced by identical local controllers forming a daisy-chain structure. Phase-shedding decisions are taken locally based on a local inductor current monitoring and threshold crossing management. This control strategy allows to implement as many phases as desired in a modular manner. In order to handle specific events such as load current inrush or a start-up sequence and to guarantee optimal transient responses, additional functions are included into each local controllers. The inter-cell communication protocol is described, along with necessary design considerations of threshold and timing values. Finally, functional simulations are carried out on a 5-leg 12V/1.2V 60W multiphase converter, which validate the proposed decentralized phase-shedding strategy for a microcontroller power supply implementation.

Based on the principle of Pancharatnam-Berry phase, we propose an approach to construct dual-functional dielectric metasurface doublets. This type of doublet, which is composed of a substrate and two metasurface layers, performs two different functionalities at two different operating wavelengths. The simulated results of the examples show that the designed dual-functional doublet works well as expected. The proposed approach can be used to design dielectric meta-structures with more layers of meta-surface and thereby with more functionalities, and would be of interest for miniaturization and integration.

Analytical solutions for radiation dominated phase of Quasi Steady State Cosmology in Friedmann-Robertson-Walkar models are obtained. We find that matter density is positive in all the cases (k = 0,-1,1). The nature of Hubble parameter (H) in [0,2] is discussed. The deceleration parameter (q) is marginally less than zero indicating accelerating universe. The scale factor (S) is graphically shown with time. The model represents oscillating universe between the above mentioned limits. Because of bounce in QSSC, the maximum density phase is still matter dominated. The models represent singularity free model. We also find that the models have event horizon i.e. no observer beyond the proper distance rH can communicate each other in FRW mdels for radiation dominated phase in the frame work of QSSC. The FRW models are special classes of Bianchi type I, V, IX space-times with zero, negative and positive curvatures respectively. Initially i.e. at  = 0, the model represents steady model. We have tried to show how a good fit can be obtained to the observations in the framework of QSSC during radiation dominated phase.

Hierarchical tungsten oxide assemblies such as spindle-like, flowers with sharp petals, nanowires and regular hexagonal structures are successfully synthesized via a solvothermal reduction method by simply adjusting the reaction conditions. On the basis of the experimental results, it is determined that the reaction time significantly influences the phase transition, microstructure and photocatalytic activity of the prepared samples. The possible mechanisms for the phase transition and morphology evolution process have been systematically proposed. Moreover, the as-prepared products exhibit significant morphology-depended photocatalytic activity. The flower-like W18O49 prepared at 6 h possesses large specific surface area (150.1 m²g^-1), improved separation efficiency of electron-hole pairs and decreased electron-transfer resistance by the photoelectrochemical measurements. As a result, the flower-like W₁₈O₄₉ prepared at 6 h exhibits the highest photocatalytic activity for the degradation of Methyl orange aqueous solution. The radical trap experiments showed that the degradation of MO was driven mainly by the participation of h⁺ and •O²⁻ radicals.

Elastic properties of materials and their changes with temperature are important for their applications in engineering. A study on the influence of phase composition of AISI 4130 alloy on Young's modulus (Ed), shear modulus (Gd), and damping (Q-1) was carried out by Impulse Excitation Technique (IET). The material characterization was carried out using confocal microscopy, XRD, MET, HV, and dilatometry. A stable structure, composed of ferrite (BCC) and pearlite (α-Fe+Fe3C), was obtained by annealing. Metastable structure of martensite (BCT) was obtained by quenching. The Ed, Gd, and Q-1 were measured, varying the temperature from RT to 900 °C. The values of Ed and Gd, at RT, were determined as 201.5 and 79.2 GPa (annealed), and 190.13 and 76.5 GPa (quenched), respectively. In the annealed steel, the values Ed and Gd decrease linearly on heating up to 650 °C, with the thermal expansion. In the quenched steel, weak changes in the dilatometric curve, Ed, Gd, and Q-1, in the range of 350-450 °C, indicated decompositions of the martensitic phase. Sharp decrease in the moduli and high peak of Q-1, was observed for both samples around 650-900 °C, revealing low lattice elastic stability of the phases during transformations α(BCC)+Fe3C↔γ(FCC).

Super duplex stainless steel (SDSS) is used for manufacturing large valves and pipes in offshore plants because of its excellent strength and corrosion resistance. Large valves and pipes are manufactured by forging after casting, and the outside and inside microstructures are different owing to the difference in the cooling rate caused by the thermal conductivity. This microstructural variation causes cracks during solution annealing, which breaks the materials. To study toe corrosion resistance of the SDSS forged material, the microstructure was conducted based on the difference in the cooling rate between the inside and outside of the cast SDSS. To analyze the effects of the secondary phase fraction before solution annealing on the solution and corrosion resistance, the corrosion resistance with and without solution annealing was measured using the potentiodynamic polarization test and critical temperature test after the precipitation of the secondary phase. In the potentiodynamic polarization test, the secondary phase decreased the activation polarization and increased the corrosion rate. The critical pitting temperature exhibited the effect of the secondary phase.

The availability of sufficient amounts of form I of benzocaine has led to the investigation of its phase relationships with the other two existing forms II and III using adiabatic calorimetry, powder X-ray diffraction, and high-pressure differential thermal analysis. The latter two forms were known to have an enantiotropic phase relationship with form III stable at low-temperature and high-pressure, while form II is stable at room temperature. Using adiabatic calorimetry data, it can be concluded, that form I is the stable low-temperature, high-pressure form, which also happens to be stable at room temperature; however, form II, due to its persistence at room temperature, is still the most convenient polymorph to use in formulations. Form III presents a case of overall monotropy and does not possess any stability domain in the pressure-temperature phase diagram. Heat capacity data for benzocaine have been obtained by adiabatic calorimetry from 11 K up to 369 K above its melting point, which can be used to compare to results from in-silico crystal structure prediction.

Lamb waves occur in thin-walled structures in two wave modes, the symmetric and antisymmetric mode. Their oscillation on the structures‘ surfaces is either in phase (symmetric) or shifted by a phase angle of π (antisymmetric). In this work, a method is developed to compare the surfaces‘ oscillation phase relation. It is based on the evaluation of time signals regarding the instantaneous phase angle using the continuous wavelet transformation and as a comparative method the short-time Fourier transformation. For this purpose, numerical simulations utilizing the finite element method provide time signals from the top and bottom surface of different thin-walled structures. They differ with respect to their material settings and laminate configurations. The numerically obtained time signals are evaluated by the developed methods. The occurring oscillation phase differences on the top and bottom surface are studied and both methods are compared. Subsequently, the oscillation phase is evaluated experimentally for the wave propagation in a fiber metal laminate. It is shown that the method based on the continuous wavelet transformation is suitable for the evaluation of oscillation phase relations in time signals. Additionally, it is proven that fiber metal laminates show only two phase relations which indicates the occurrence of Lamb waves.

Phase imaging of biochemical samples has been demonstrated for the first time at the Infrared Microspectroscopy (IRM) beamline of the Australian Synchrotron using the usually discarded Near-IR (NIR) region of the synchrotron-IR beam. The synchrotron-IR beam at the Australian Synchrotron IRM beamline has a unique fork shaped intensity distribution as a result of the gold coated extraction mirror shape, which includes a central slit for rejection of the intense X-ray beam. The resulting beam configuration makes any imaging task challenging. For intensity imaging, the fork shaped beam is usually tightly focused to a point on the sample plane followed by a pixel-by-pixel scanning approach to record the image. In this study, a pinhole was aligned with one of the lobes of the fork shaped beam and the Airy diffraction pattern was used to illuminate biochemical samples. The diffracted light from the samples was captured using a NIR sensitive lensless camera. A rapid phase-retrieval algorithm was applied to the recorded intensity distributions to reconstruct the phase information corresponding to different planes. The preliminary results are promising to develop multimodal imaging capabilities at the IRM beamline of the Australian Synchrotron.

To enhance the mechanical properties (i.e. strength and elongation) of the face-centered cubic (fcc) α-phase in the Au-Cu-Al system, this study focused on the introduction of the martensite phase (doubled B19 (DB19) crystal structure of Au2CuAl) via the manipulation of alloy compositions. Fundamental evaluations, such as microstructure observations, phase identifications, thermal analysis, tensile behavior examinations, and reflectance analysis have been conducted. The presence of fcc annealing twins was both observed in the optical microscope (OM) and the scanning electron microscope (SEM) images. Both the strength and elongation of the alloys were greatly promoted while the DB19 martensite phase was introduced into the alloys. Amongst all the prepared specimens, the 47Au41Cu12Al and the 44Au44Cu12Al alloys performed the optimized mechanical properties. The enhancement of strength and ductility in these 2 alloys was achieved while the stress plateau was observed during the tensile deformation. A plot of the ultimate tensile strength (UTS) against fracture strain was constructed to illustrate the effects of the introduction of the DB19 martensite phase on the mechanical properties of the alloys. Regardless of the manipulation of the alloy compositions and the introduction of the DB19 martensite phase, the reflectance stayed almost identical to pure Au.

Managing sidelobe levels (SLLs) in metasurface-driven beam-steering antennas poses a significant challenge due to intrinsic factors leading to grating lobes. Our proposed method employs an equivalent model to optimize large periodic metasurfaces efficiently. This model predicts complete metasurface performance, accounting for mutual coupling between patches. We introduce an evolutionary optimization algorithm based on the Cross Entropy (CE) method to enhance PGM-based beam-steering antennas and suppress sidelobes. Two strategies were employed: first is to optimize the patch dimensions for a sidelobe-free pattern and the second is to maintain the PGM dimensions while optimizing feed array amplitudes. Both strategies effectively suppressed sidelobes, offering insights into the CE method's applicability and effectiveness for CPU-intensive electromagnetic optimization challenges. The proposed CE method variant retains its simplicity while improving monitoring capabilities, addressing this limitation. Smaller generations yield better improvements per evaluation

The brown pelican (Pelecanus occidentalis) is a species often affected by natural and man-made disasters such as hurricanes and oil spills as well as general human activities; that subsequently receives medical care and rehabilitation. During rehabilitation, blood may be collected for various testing to help with diagnosis, treatment, and monitoring. Reference intervals for this species are limited, dated, and typically from small sample sizes. Seventy one presumed healthy brown pelicans were sampled as a part of their pre-release examination from rehabilitation at the Wildlife Center of Texas after a large volume stranding in December 2014 to January 2015, and various venous analytes were measured to establish updated reference intervals for Brown Pelicans. Fibrinogen was measured via heat precipitation and the Abaxis VSPro equine Fibrinogen cartridge to determine reference intervals, and in an attempt to validate the VSPro for use in avian species. Abaxis VS2 Avian/Reptile Chemistry panel, iSTAT CG4+, and iSTAT Chem8+ results in addition to body condition score, spun PCV, cloacal temperature and fibrinogen were measured. Proposed reference intervals for brown pelicans are presented. Fibrinogen results were not comparable between the gold standard method and the VSPro, indicating that the VSPro is not appropriate for use in brown pelicans.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

Hydrogen from natural gas reforming can be produced efficiently with a high CO2 capture rate. This can be achieved with oxygen-blown autothermal reforming as core technology combined with pressure-swing adsorption for hydrogen purification and refrigeration-based tail gas separation for CO2 capture and recirculation of residual hydrogen, carbon monoxide and methane. The low-temperature tail gas separation section is presented in detail, and to quantify the exergy efficiency of this section, a detailed exergy analysis is conducted. The irreversibilities in 42 different process components are quantified. In order to provide a transparent verification of the consistency of exergy calculations, the total irreversibility rate is calculated by two independent approaches: Through the bottom-up approach, all individual irreversibilities are added to obtain the total irreversibility rate. Through the top-down approach, the total irreversibility rate is calculated solely by the exergy flows crossing the control volume boundaries. The consistency is verified as the comparison of results obtained by the two methods shows a relative deviation of 4·10-7. The exergy efficiency of the CO2 capture process is calculated based on two different definitions. Both methods give a baseline exergy efficiency of 58.38%, which indicates a high degree of exergy utilisation in the process.

Computational Fluid Dynamics (CFD) is revolutionizing the oil and gas industry by offering powerful insights and innovative solutions. This paper explores the cutting-edge applications of CFD in enhancing and innovating within the sector. CFD simulations provide engineers with invaluable insights into fluid behavior, enabling optimized designs and informed decision-making. The software facilitates foresight by predicting system performance, optimizing drilling techniques, and maximizing reservoir management strategies. Moreover, CFD optimizes equipment design, increases operational efficiency, and reduces costs through virtual testing, eliminating the need for costly physical prototypes. The application of CFD aligns with the United Nations Sustainable Development Goals (SDGs), promoting energy efficiency, climate action, responsible production, and sustainable consumption. It addresses flow assurance challenges, enhances safety protocols, and mitigates environmental impacts. CFD is a powerful tool driving innovation, resilience, and sustainability within the oil and gas industry, ensuring a more efficient, safe, and environmentally conscious future. As advancements in CFD methodologies continue, the potential for further enhancements and breakthroughs within the sector becomes even more promising, driving the industry towards a sustainable and prosperous future.

Cellulose-based carbon (CBC) has been widely concerned with its porous structure, high specific surface area, and is liable to adsorb gas molecules and macromolecular pollutants. However, the application of CBC in gas sensing has been little studied. In this paper, ZnO/CBC heterojunction was formed by means of simple co-precipitation and high temperature carbonization. As a new ammonia sensor, the prepared ZnO/CBC sensor can detect ammonia compared with that of the previous pure ZnO ammonia sensor can not at room temperature. It has great gas sensing response, stability and selectivity to ammonia concentration at 200 ppm. This study provides a new idea for the design and synthesis of biomass carbon-metal oxide composites.

The scope of this paper is to use plastic waste through the gasification process for producing electricity with low carbon dioxide emissions. Worldwide, plastic production increased, reaching 367 million tons in 2020, compared with 1.5 million tons in 1950. It is known that plastic incineration generates approximately 400 million tons of CO2 annually, and consequently, new solutions for a more efficient plastics reuse in terms of emissions generated are still expected. One method is to use plastic waste in a gasifier unit and the syngas generated in a gas turbine for electricity production. The co-gasification process (plastic waste with biomass) was analysed in different ratios. Gasification was carried out with air for an equivalent ratio (ER) between 0.10-0.45. The volume concentration of CO2 in syngas ranged from 2-12%, with the highest value obtained when poplar content in the mix was 95%. In this study, the option of pre- and post-combustion integration of the chemical absorption process (CAP) was investigated. Thus, CO2 emissions have decreased by 90% compared with the case without CO2 capture. By integrating the capture process, the global efficiency has reduced with 5.5 – 6.1 percentage points in a post-combustion case, according to the plastic content in the mix.

Detection of partial discharge (PD) activities in high-voltage equipment can be done according to the several mechanisms of signal detection, which are electromagnetic wave signal detection, acoustic signal detection, chemical reactions, electrical signal detection, or optical emission detection. Recently, multiple methods of detection and localization of partial discharge activities occurred in power transformers and gas-insulated switchgear (GIS) have been proposed to monitor the health condition of high-voltage equipment, especially when the awareness regarding preventive maintenance has been emphasized at the industrial level and electrical providers. In aligning the needs of industrial and the improvement of PD detection methods, this manuscript focused on reviewing the current practice methods for the detection and localization of PD signals in high-voltage equipment and comparing their efficacy, in summarizing the future direction of research work-related methods of PD detection. The comparative reviews are discussed in terms of the mechanism of PD signal detection, indication parameters, calibration technique, advantages, and limitations of each method of PD measurement in detail.

Methane is the main cause of sewer explosion accidents, and the available monitoring methods mainly use portable gas sensors for on-site detection. However, these methods cannot grasp the dynamic changes in methane in a sewer in real time or make better predictions of methane explosion accidents. Here, we present a low-power online monitoring system for sewer methane in order to ensure the safety of urban sewers. A low-power ultrasonic gas sensor was used to monitor the methane content in biogas. Due to the impacts of changes in CO2, temperature, and humidity in the sewer on the ultrasonic methane measurement results, a corresponding compensation method was proposed. The effectiveness of the compensation method was verified through experiments, which measured the methane concentration under different influences, and the methane values measured before and after compensation were compared. The power consumption was only 1.28 mW if the system worked in intermittent operation mode, and it could operate for about 1.5 years by selecting a lithium battery with a capacity of 5 A · H. The experimental results showed that the gas detection accuracy could meet the commercial requirements and had a high compensation for the impacts of carbon dioxide, temperature, and humidity.

A set of aromatic copolyimides was obtained by reaction of 4,4′-(hexafluoroisopropylidene) diphthalic anhydride (6FDA), and mixtures of the diamines 1,4-bis(4-amino-2-trifluoromethylphenoxy)-2,5-di-tert-butylbenzene (CF3TBAPB) and 3,5-diamino benzoic acid (DABA). These polymers were characterized and compared with the homopolymer derived from 6FDA and CF3TBAPB. All copolyimides showed high molecular weight values and good mechanical properties. The presence of carboxylic groups in these copolymers allowed their cross-linking by reaction with 1,4-butanediol. The crosslinked polymer films were extensively characterized and it was observed that the degree of crosslinking was low in the copolyimides possessing a small number of carboxyl groups. The degradation temperature of these crosslinked copolyimides was lower than their corresponding non-crosslinked ones. Glass transition temperatures were higher than 260 oC, showing the non-crosslinked copolyimides the highest values. Young moduli of these crosslinked showed values higher than 1.9 GPa, and slightly lower elongation at break when compared with the precursor copolyimides. All copolyimides (precursor, and crosslinked ones) films could be tested as gas separation membranes. It was seen that CO2 permeability values were around 100 barrer, having better selectivity than that of the homopolymer. Moreover, the plasticization resistance of the crosslinked material having a large number of carboxylic groups was excellent.

This investigation was conducted to determine the chemical composition and nutritional value of five plant species commonly used as ruminant feeds namely: Artemisia herba-alba, Acer monspessulanum, Amygdalus lycoides, Amygdalus scoparia, and Atriplex leucoclada. After the collecting samples, the chemical compositions of plants included dry matter (DM), organic matter (OM), crude protein (CP), ether extract (EE), ash (CA), cell wall (NDF), and non-lignin cell wall (ADF) were determined according to standard methods. For degradation testing, the nylon bag technique was applied using three native Sistani fistula calves. Organic matter digestibility (OMD) and metabolisable energy (ME) were determined through the gas production technique. The CP value ranged from 5.30 (Amygdalus scoparia) to 11.72% (Atriplex leucoclada) while NDF value ranged from 52.62 (Amygdalus lycoides) to 69.05% (Amygdalus scoparia). The range of OMD, DOMD, and ME was from 36.67 to 53.27%, 34.67 to 49.11%, and 5.57 to 8.08 (MJ/kg), respectively. The results showed a positive correlation between cell wall composition and dry matter digestibility in plant species. The nutritional value of Amygdalus lycoides, Atriplex leucoclada, Acer monspessulanum, and Artemisia herba-alba was acceptable composition and digestibility.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

Background: Qazvin province has suffered a lot of natural disasters (earthquakes) for a long time. so, the establishment of the first industrial city in Iran, has always been a source of concern. One of these problems is the possibility of chlorine gas leaking from the chlorination system of drinking water and treatment plant the existing ones are on the health of the inhabitants of this region.Material and method: This analytical study was carried out in Novorossiysk district of Alborz in December 2012. Initially, chlorine gas leakage scenarios from these facilities were simulated by ALOHA and WISER software, and then using the Emergency Level System, according to the CCPS Consultative Center's Chemical Process Safety Advice, the Emergency Response Program was presented. Results: ALOHA software, in comparison with WISER software, has more precision to identify and address the consequences of chlorine gas leakage hazards and according to the simulation of this software in the event of a leak from the well and water resources unit at 8240 m from the area and at night 7520 meters will be affected. Due to the speed of delivering results through the WISER software, this software can be used at times when the operating speed is considered (incident time).Conclusion: According to the CCPS model, the emergency conditions were classified at levels 3 and 4, therefore, the relevant crisis management agencies (Qazvin Crisis Management Committee, Alborz City Health Center, Red Crescent and Firefighting Authority) should provide training maneuvers At Alborz city level, and informing people of cities and industrial companies, many efforts have been made to reduce human and environmental damage in case of possible leakage.

The aim of the study was to examine the biogas and methane yield of maize silage, a wastes in agricultural point of view and compare it to the biogas productivity of commonly used mixture of maize silage and mixed fodder with water. The experimental study was carried out into 2 parts. Firstly, the batch experiment was conducted in Mesophilic conditions (35°C), at five different hydraulic retention times (HRT): 6 DAT, 11 DAT 20 DAT 29 DAT and 41 DAT. The results revealed that maize silage was generated the highest biogas yield of 537 mL /241 mL at the HRT of 6days /41 days. Mixed fodder produced the highest biogas yield of 421 mL at the HRT of 6th days and the lowest one was 252 mL at the HRT of 20th days. Finally, the methane, carbon dioxide and hydrogen sulphide of biogas produced from maize silage and mixed fodder were analyzed using a gas chromatography. The results shown that biogas from maize silage precedes the gas less than the mixed fodder. In the field level experiment proved that from mixed fodder produced gas which would be enough for 7 member’s family used 3 months for the purpose of their cooking.

Gas membrane-based separation is considered one of the furthermost effective technology to address energy efficiency and large footprint challenges. Various classes of advanced materials including polymers, zeolites, porous carbons and metal–organic frameworks (MOFs) were attempted as membranes for gas separation. MOFs, among other porous materials, possess uniquely tunable nature, in which the pore size and environment can be controlled by connecting metal ions (or metal ion clusters) with organic linkers with various functionalities. This feature makes them attractive for thin membrane fabrication, as both diffusion and solubility components of permeability can be altered. It is interesting to notice that numerous reports have addressed the synthesis of different MOFs, fabrication of their corresponding thin films and their applications, nonetheless, relatively limited studies addressed their gas separation application as membranes. In this review, we provide a synopsis of the various MOF-based membranes that were fabricated in the last decade. In this review we propose a short introduction touching on the gas separation membrane technology and we shed light on (i) the various techniques developed for the fabrication of MOF as membranes and (ii) challenges and application for MOF thin film membranes in various important gas separation applications.

Accent is on determination of appropriate friction factor of the pipes and on selection of the representative equation for water or natural gas flow which is valuable for existing conditions in the looped network of pipelines. Note that in a municipal gas pipeline, natural gas can be treated as incompressible fluid (liquid) i.e. as water or oil. Even under this circumstance, calculation of water pipelines cannot be literary copied and applied for calculation of gas pipelines. Inappropriate friction factor, equally as e.g. inappropriate usage of water flow equations for calculation of gas networks can lead to inaccurate final results. Few iterative methods for determining the optimal hydraulic solution of water- and gas- looped pipeline networks, such as, Hardy Cross, modified Hardy Cross, node-loop method, node and M.M. Andrijashev method, will be shown. Speed of convergence will be compared and discussed using a simple network with three loops.

Due to failure of the continuum hypothesis for higher Knudsen numbers, rarefied gases and microflows of gases are particularly difficult to model. Macroscopic transport equations compete with particle methods, such as DSMC to find accurate solutions in the rarefied gas regime. Due to growing interest in micro flow applications, such as micro fuel cells, it is important to model and understand evaporation in this flow regime. Here, evaporation boundary conditions for the R13 equations, which are macroscopic transport equations with applicability in the rarefied gas regime, are derived. The new equations utilize Onsager relations, linear relations between thermodynamic fluxes and forces, with constant coefficients, that need to be determined. For this, the boundary conditions are fitted to DSMC data and compared to other R13 boundary conditions from kinetic theory and Navier-Stokes-Fourier (NSF) solutions for two one-dimensional steady-state problems. Overall, the suggested fittings of the new phenomenological boundary conditions show better agreement to DSMC than the alternative kinetic theory evaporation boundary conditions for R13. Furthermore, the new evaporation boundary conditions for R13 are implemented in a code for the numerical solution of complex, two-dimensional geometries and compared to NSF solutions. Different flow patterns between R13 and NSF for higher Knudsen numbers are observed.

The article discusses the validation process of a certain method of balancing gas contained in the pore space of rocks. The validation was based upon juxtaposition of the examination of rocks' porosity and the effects of comminution in terms of assessing the possibility of opening the pore space. The tests were carried out for six dolomite samples taken from different areas of the 'Polkowice-Sieroszowice’ copper mine in Poland. Before the rock material was ground, it was examined using the porosimetric method and subsequently subjected to the SEM analysis. After grinding, the research material was subjected to the granulometric analysis. Prior to the grinding process, the rocks' porosity fell in the range of 0.3-14.8%, while the volume of the open pores was included in the 0.01-0.06 cm3/g range. The research material was also characterized by inhomogeneous distribution of the pore volume. The grinding process was performed using an original device – the GPR analyzer. The ground samples were characterized by similar particle size distribution and mean diameters D_3.2 of about 4.0-4.5 µm. The SEM analysis revealed pores of various size and shape on the surface of the rock cores, while at the same time demonstrating lack of pores following the grinding process. The grain size distribution curves were compared with the cumulative pore volume curves of the cores before grinding. The resulting intersection points of both curves were seen as testifying to the presence of openings in the rock pores and release of the accumulated gas. The opening percentage of the pore space was associated with the coordinates of the curves' intersections. In order to confirm the argument put forward in this paper – i.e. that comminution of a rock to grains of a size comparable with the size of the rock's pores results in the release of gas contained in the pore space – the amount of gas released as a result of the comminution process was studied. The results of gas balancing demonstrated that the pore space of the investigated dolomites was filled with gas in amounts from 3.19 cm3/kg to 45.86 cm3/kg. The obtained results of the rock material comminution to grains comparable – in terms of size – to the size of the pores of investigated rocks, along with asserting the presence of gas in the pore space of the studied dolomites, were regarded as a proof that the method of balancing gas in rocks via rock comminution is correct.

The air in subterranean karst cavities is often depleted in methane (CH₄) relative to the atmosphere. Karst is considered a potential sink for the atmospheric greenhouse gas CH₄ because its subsurface drainage networks and solution-enlarged fractures facilitate atmospheric exchange. Karst landscapes cover about 14% of earth’s continental surface, but observations of CH₄ concentrations in cave air are limited to localized studies in Gibraltar, Spain, Indiana (USA), Vietnam, Australia, and by incomplete isotopic data. To test if karst is acting as a global CH₄ sink, we measured the CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values of cave air from 33 caves in the USA and three caves in New Zealand. We also measured CO₂ concentrations, δ¹³C_CO2, and radon (Rn) concentrations to support CH₄ data interpretation by assessing cave air residence times and mixing processes. Among these caves, 35 exhibited subatmospheric CH₄ concentrations in at least one location compared to their local atmospheric backgrounds. CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values suggest that microbial methanotrophy within caves is the primary CH₄ consumption mechanism. Only 5 locations from 3 caves showed elevated CH₄ concentrations compared to the atmospheric background and could be ascribed to local CH₄ sources from sewage and outgassing swamp water. Several associated δ¹³C_CH4 and δ²H_CH4 values point to carbonate reduction and acetate fermentation as biochemical pathways of limited methanogenesis in karst environments and suggest that these pathways occur in the environment over large spatial scales. Our data show that karst environments function as a global CH₄ sink.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

As novel materials for carbon capture, phase change solvents can separate into two immiscible phases during the CO2 capturing procedure under a certain temperature. The solvent systems can significantly decrease the energy consumption since the solvents can be regenerated by only heating the rich-CO2 phase. In this work, amino acid ionic liquids (AAILs) were synthesized using quaternary ammonium salts and amino acids as raw materials, and the aqueous solutions were prepared as novel liquid-solid phase change solvents. The results showed that the solvents had excellent CO2 absorption capacity, and the AAILs functionalized by glycine and tryptophan exhibited significant phase change properties. The mechanism of phase-change of the solvent were mainly due to the lower solubility of the product after reaction between AAILs and CO2. The solvent with tryptophan as anion could be regenerated by only heating the CO2-riched solid phase, which might significantly decrease energy consumption of regeneration. And the absorbent could be reused with the regenerated absorption ratio up to 79%. The solvent system has great potential in industrial application due to the easy operation process and efficient recycling ability.

Numerical models widely used for hydrocarbon phase behavior and compositional flow simulations are based on assumption of thermodynamic equilibrium. However, it is not uncommon for oil and gas-condensate reservoirs to exhibit essentially non-equilibrium phase behavior, e.g., in the processes of secondary recovery after pressure depletion below saturation pressure, or during gas injection, or for condensate evaporation at low pressures. In many cases the ability to match field data with equilibrium model depends on simulation scale. The only method to account for non-equilibrium phase behavior adopted by the majority of flow simulators is the option of limited rate of gas dissolution (condensate evaporation) in black oil models. For compositional simulations no practical yet thermodynamically consistent method has been presented so far except for some upscaling techniques in gas injection problems. Previously reported academic non-equilibrium formulations have a common drawback of doubling the number of flow equations and unknowns compared to the equilibrium formulation. In the paper a unified thermodynamically-consistent formulation for compositional flow simulations with non-equilibrium phase behavior model is presented. Same formulation and a special scale-up technique can be used for upscaling of an equilibrium or non-equilibrium model to a coarse-scale non-equilibrium model. A number of test cases for real oil and gas-condensate mixtures are given. Model implementation specifics in a flow simulator are discussed and illustrated with test simulations. A non-equilibrium constant volume depletion algorithm is presented to simulate condensate recovery at low pressures in gas-condensate reservoirs. Results of satisfactory model matching to field data are reported and discussed.

India, the world’s most populous country, is the world's third-largest emitter of greenhouse gases (GHGs). Despite employing several energy sources, it still relies heavily on coal, its primary energy source. Given India’s swiftly rising energy demand, this challenges meeting emission reduction targets. India has significantly increased investments in renewables like solar and hydrogen in recent years. While commendable, these initiatives alone cannot meet the country's expanding energy demands. In the short term, India must rely on both domestic and imported fossil fuels, with natural gas being the most environmentally friendly option. In this context, this paper attempts to forecast energy consumption, natural gas production, and consumption in India till 2050 using both univariate and multivariate forecasting methods. For multivariate forecasting, we have assumed two alternative possibilities for GDP growth: the business-as-usual and the high-growth scenarios. Each of our forecasts indicates a notable shortfall in the projected production of natural gas compared to the expected demand, implying our results are robust. Our model predicts that nearly 30-50 percent of India’s natural gas consumption will be met by imports, mainly in the form of LNG. Based on these findings, this paper recommends that Indian government policies emphasize increasing domestic natural gas production, importing LNG, and expanding renewable energy resources.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

Recent inference results of the sound velocity in the cores of neutron stars are summarized. Implications for the equation of state and the phase structure of highly compressed baryonic matter are discussed. In view of the strong constraints imposed by the heaviest known pulsars, the equation of state must be very stiff in order to ensure the stability of these extreme objects. This required stiffness limits the possible appearance of phase transitions in neutron star cores. In view of these empirical findings, much discussed issues such as the quest for a phase transition towards restored chiral symmetry and the active degrees of freedom in cold and dense baryonic matter, are explored.

Outbreaks of the desert locust Schistocerca gregaria affect some of the poorest parts of Africa, causing devastating catastrophes. Key to understanding and dealing with this problematic adaptation to environmental changes is comparing locusts that are gregarious (associated with outbreak states) and solitarious (associated with non-outbreak states) either in nature or after experimental treatments in laboratories. Categorising locusts and detecting changes in their phase status is key to such comparisons. Such comparisons are hitherto based on applying mathematical models that use behavioural parameters and that each laboratory has to build a new for each experiment. All such models used thus far for research on locusts are different from each other. That implies differences in the tools used for the different experiments and by the different laboratories and, thus, potential noise in the scientific results and interpretations too. Standardizing the way how we categorise locusts between laboratories and experiments is needed if we want to reduce noise and errors. It is even a must if we are to make the results and interpretations transferable and comparable between experiments and laboratories that work in such an important research area. Here, we use samples from independent S. gregaria population in order to further test the two models that were suggested earlier as standardizing tools for S. gregaria categorization. The outcomes of both models were largely replicated and reproducible. We report on how successful the two models were at categorizing solitarious, intermediate (transient) and gregarious nymph and adult samples. We highlight shortcomings and make more specific recommendations on the use of these models based on the differences they show as to their precision when categorizing the solitarious and gregarious S. gregaria nymph and adult samples.

The quadratic polynomial differential systems in the plane are the easiest nonlinear differential systems. They have been studied intensively due to their nonlinearity and to their big number of applications. These systems can be classified in ten classes. Here we provide all the topologically different phase portraits in the Poincaré disc of two of these classes.

Online speech enhancement is of great interest, because of its diverse areas of application. The Demucs architecture has been recently shown to achieve a high level of performance, even with small audio segments, while requiring a relatively small amount of computational resources. However, an issue that it bears, as well as most of state-of-the-art speech enhancement techniques, is that of target speech selection: it is assumed that only one speech source is present. However, in real-life scenarios, more than one speech source may be present, in it is uncertain which speech source within the fed mixture should be enhanced. Thus, it is of interest to complement speech enhancement techniques (such as Demucs-based) with a target selection scheme, so as to ensure that only the source of interest is enhanced. In this work, two target selection strategies are explored: 1) an embedding-based strategy, using a codified sample of the target speech, and 2) a location-based strategy, using a beamforming-based pre-filter to select the target that is in front of a 2-microphone array. It is shown that while both strategies improve the performance of the Demucs-based technique when one or more speech interferences are present, they both have their pros and cons. Specifically, while the beamforming-based strategy achieves overall a better performance compared to the embedding-based strategy, it is sensitive against the location variation of the target speech source which the embedding-based strategy does not suffer from.

Enhancement in chemisorption is one of the active research areas in carbon materials. To remedy the thermally degraded chemisorption at high temperatures, we report a comprehensive study of kink structures in free-standing monoatomic carbon nanowires upon heating. Our Monte Carlo simulation considers multi-monoatomic carbon chains laterally interacted by the Van der Waals force. Our study reveals that the carbon nanowires maintain their linearity regardless of chain length at low temperatures, but this is not the case at high temperatures. Disordered kink structure is observed in the short carbon chains, especially above the Peierls transition temperature. The severe kink structure might increase the possibility of attaching negatively charged atoms, thereby contributing to the development of next-generation materials for chemisorption at high temperatures. We have also provided an important inspection that any physical property of the finite-length carbon chain predicted by ab-initio calculation should reconsider the atomic rearrangement due to the thermal instability at high temperatures.

Rapid solidification during metal additive manufacturing (AM) leads to non-equilibrium microsegregation, which can result in the formation of detrimental phases and cracking. Most of the microsegregation models, assume a Scheil-type solidification, where the solidification interface is planar and there exists local equilibrium at the interface along with either zero or infinite solute diffusion in the respective participating phases - solid and liquid. This assumption leads to errors in prediction. One has to account for finite solute diffusion and the curvature at the dendritic tip for more accurate predictions. In this work, we compare different microsegregation models that do and do not consider finite diffusion and dendrite tip kinetics against the experiments. We also propose a method to couple dendrite tip kinetics with the diffusion module (DICTRA®) implemented in Thermo-Calc®. The models which accounted for both finite diffusion and dendrite tip kinetics matched well with the experimental data.

Nickel-base superalloys like VDM 780 may possess a high content of Cr and Co. This influences solution energies of phase-forming elements like Al and Ta (γ′-phase), Nb (γ′′- and δ-phase), and Ti (η-phase). We perform density functional theory studies of a nickel matrix at 0 K with high concentrations of either Co and Cr and calculate the influence of these elements on solution energies. In the case of Co, the solution energy can be predicted well by the nearest-neighbor interaction in the Co-rich matrix. For Cr, the effect is more complicated because Cr has a larger ionic radius and changes the magnetic state of the material. The effect of a Cr-rich matrix on the energy of Co is dominated by magnetic effects, interactions with the other elements by elastic deformation of the lattice.

Within the spectrum of a natural image, the amplitude of modulation decreases with spatial frequency. The speed of such an amplitude decrease, or the amplitude spectrum slope, of an image affects the perceived aesthetic value. Additionally, a human observer would consider a symmetric image more appealing than they do an asymmetric one. We investigated how these two factors jointly affect aesthetic preferences by manipulating both the amplitude spectrum slope and the symmetric level of images to assess their effects on aesthetic preference on a 6-point Likert scale. Our results showed that the preference ratings increased with the symmetry level but had an inverted U-shape relation to amplitude spectrum slope. In addition, a strong interaction existed between symmetry level and amplitude spectrum slope on preference rating, in that symmetry can amplify the amplitude spectrum slope’s effects. Such effects can be described by a quadratic function of the spectrum slope. That is, preference is an inverted U-shape function of spectrum slope whose intercept is determined by the number of symmetry axis. In addition, the interaction between the two factors is manifested as the modulation depth of the quadratic function.

The TanDEM-X mission is acquiring a new dataset to provide a temporally independent DEM, called "TanDEM-X Change DEM". This set of acquisitions taken between 2017 and 2020 has a clear temporal separation to the TanDEM-X global DEM data which were acquired between 2010 and 2015. Therefore, this new DEM aims to enable the characterization of terrain changes. Improvements in the acquisition planning and the data processing were necessary to generate this Change DEM with fewer acquisitions but still very high accuracy. For this, the use of an edited TanDEM-X DEM as a "starting point" for the interferometric processing is mandatory.

Cyclin dependent kinase 1 (CDK1) has been primarily identified as a key cell cycle regulator in both mitosis and meiosis. Recently, an extramitotic function of CDK1 emerged when evidence was found that CDK1 is involved in many cellular events that are essential for cell proliferation and survival. In this review we summarize the involvement of active CDK1 in the initiation and elongation steps of protein synthesis in eukaryotes. During its activation CDK1 influences the initiation of protein synthesis, promotes the activity of specific translational initiation factors and affects the functioning of a subset of elongation factors. Our review provides insights into gene expression regulation during the transcriptionally silent cell cycle/M-phase and describes quantitative and qualitative translational changes based on the extramitotic role of the cell cycle master regulator CDK1, to optimize temporal synthesis of proteins to sustain division-related processes: mitosis and cytokinesis.

The World Health Organisation declared Covid-19 as a pandemic on 11th March 2020. The main approach to tackle Covid-19 worldwide is to screen and provide supportive care to patients. For screening purpose RT-qPCR based test are used as an initial detections assay. The test is expensive, time consuming and not suitable for mass scale screening/ confirmation requirement. A recent advancement is development of Immunoassay procedures (liquid Phase tests or bed side 10-20minute strip test). In order to help and accelerate bringing life to normal after lock down, Pakistan is in dire need to develop and adopt the immunoassay procedures for mass scale screening and confirmation of COVID-19 infection. It is cheap and easy to perform without a lab requirement.

Future, flexible thermal energy conversion systems require new, demand-optimized high-performance materials. The High performance Ferritic (HiperFer) stainless steels, under development at the Institute of Microstructure and Properties of Materials (IEK-2) at Forschungszentrum Jülich GmbH in Germany, provide a balanced combination of fatigue, creep and corrosion resistance at reasonable price. This paper outlines the scientific background of alloy performance development, which resulted in an age-hardening ferritic, stainless steel grade. Furthermore, technological properties are addressed and the potential concerning application is estimated by benchmarking versus conventional state of the art materials.

The phase composition design principle is introduced to obtain balanced properties of ionic conductivity and thermo-tolerant for zirconia solid electrolytes used in solid oxide fuel cells (SOFCs). The zirconia ceramic solid electrolytes are fabricated by two-step free sintering. With increasing Y/Mg ionic ratio from 1.78:1 to 1.88:1, the content of monoclinic phase fluctuates little (±3%). The ionic conductivity, including the total electrical resistance; grain electrical resistance and grain boundary electrical resistance at 1223K, are all gradually declining with the increasing of Y/Mg ionic ratio. Furthermore, the enrichment of Mg ion in grain boundary acts as a disincentive to grain boundary ionic conductivity. In addition, the maximum total equivalent conductivity at 1223K in this study reaches to 0.143 Scm-1 which can compare with that of certain YSZ. It will be beneficial to SOFCs application profited from increasing ionic conductivity of ceramic solid electrolytes.

The entropy of Boltzmann-Gibbs, as proved by Shannon and Khinchin, is based on four axioms, where the fourth one concerns additivity. The group theoretic entropies make use of formal group theory to replace this axiom with a more general composability axiom. As has been pointed out before, generalized entropies crucially depend on the number of allowed number degrees of freedom $N$. The functional form of group entropies is restricted (though not uniquely determined) by assuming extensivity on the equal probability ensemble, which leads to classes of functionals corresponding to sub-exponential, exponential or super-exponential dependence of the phase space volume $W$ on $N$. We review the ensuing entropies, discuss the composability axiom, relate to the Gibbs' paradox discussion and explain why group entropies may be particularly relevant from an information theoretic perspective.

The precipitate phases often play an important influence on the corrosion resistance of 2205 Duplex stainless steel (DSS). In the presented paper, the microstructure and corrosion resistance in the hot-rolled and cold-rolled 2205 DSS aging for different time at 850 °C was investigated by XRD, SEM and potentiodynamic polarization. It has been found that the Chi(χ) phase and Sigm(σ) phase were precipitated in turn after aging treatment of hot-rolled and cold-rolled materials, but the precipitate amount in cold-rolled material is much more than that of hot-rolled samples. The corrosion resistance of the solution-annealed cold-rolled material is similar to the hot-rolled material, but the corrosion resistance of cold-rolled material with precipitate is weaker than that of hot-rolled material after aging treatment. Pitting initiates preferentially in the Cr-depleted region from σ phase in aged hot-rolled 2205, and severe selective corrosion occurs on sigma/ferrite interfaces aged for a long aged lime. However, the initiation of pitting corrosion may take place at the phase boundary, defect and martensite in the aged cold-rolled 2205. The σ phase is further selectively dissolved by electrochemical method to investigate the difference of microstructure and corrosion behavior in hot-rolled and cold-rolled 2205 duplex stainless steel.

Despite the fact that strong routine separation methodologies can give reliable specificity and validity at usual working pharmaceuticals concentrations, they may fail at very low concentration levels. This poses considerable challenges for researchers inves-tigating product purity and therapeutic drug monitoring. Sensitivity enhancement pro-cedures are thus required to maximize the performance of separation techniques. Large volume injection, solid phase extraction/solid phase enrichment (SPE/SPEn), pre-, post-, and in-column derivatization, as well as the use of sensitive detection devices are the simplest strategies for improving sensitivity of the separation-based analytical techniques. Large volume injection of samples with online SPE/SPEn coupled with separation techniques increased sensitivity and improved detection as well as quantification limits without affecting peak shape and system performance. Although the primary purpose of derivatization is to improve sensitivity and selectivity, greener derivatization is growing in popularity and should be considered in analytical chemistry. In general, two strategies are essential for accomplishing greener derivatization goals. The first is the search for and use of ecologically acceptable derivatizing reagents, solvents, and reaction conditions. The second is miniaturization and automation of analytical methods. This review discusses significant advances in separation-based analytical techniques, specifically enrichment approaches and detector signal improvement for pharmaceutical quantification in various matrices at very low concentration levels. As a result of improved analytical systems setup in drug assays, the possibility of high-throughput analyses was also highlighted.

Developing a dependable gas and condensate value chain is vital for the ongoing prosperity of the oil and gas industries. To achieve this, NNPC is enhancing its production facilities by employing process modeling and simulation with the assistance of Symmetry iCON®. As a part of this initiative, a simulation model was created using the Symmetry iCON® pipe plexus solver to simulate the dynamic environment of the gas and condensate pipeline network in the Nigerian Southern region. To validate the model, data from a single month, specifically December 2022, was utilized. Furthermore, the algorithm was utilized to generate projections for the month of January 2023, providing valuable insights into its effectiveness. The study also highlighted the significance of accurately estimating the characteristics and properties of a pseudo component of C6+ in relation to thermodynamics and material properties, which was a particularly insightful finding. he assessment of this property has transitioned from being relatively unimportant to becoming critically important, primarily due to the lack of condensate data monitoring at specific terminals. However, it's worth noting that the model currently has an error margin of 4-6% when predicting the data. As more information becomes available in the future, the model can be easily fine-tuned to better align with the actual conditions, allowing for more accurate predictions.

Oil and Gas companies, both national and international, along with government regulators, share a common goal of efficiently managing their valuable assets. These assets refer to the Reserves of oil and Gas located underground. Typically, production and Reserves Engineers play a crucial role in managing these reserves through the implementation of well testing techniques. Thus far, the gold standard in this field has been to ensure the optimal management and utilization of these resources. In the context of well testing, the separator has traditionally been considered the gold standard. However, despite regulatory mandates for frequency of well testing (Such as the general requirements of every 30days in the Nigeria south East zone sector), There is a lack of specific regulations regarding the expected flow measurement uncertainties. This gap in the regulations leaves room for improvement in establishing guidelines for accurate flow measurements. This paper aim to Review the various test separator employed, examine the implications of the 30days testing interval under real - world conditions, and critically assess the achievable measurements uncertainties in the field. Additionally, it will provide a candid analysis that sheds light on the expected uncertainties associated with flow measurements. The introduction of the multiphase meters in the past two decades hold the potential for significant advancements in Reservoirs management performance. However, the authors suspect that this potential has not been universally realized. This paper aim to address this issue by examining the extent to which the benefits of multiphase meters have been effectively utilized in reservoir management. By doing so, it seeks to shed light on any existing gaps and propose recommendation for maximizing the impact of multiphase metres in the field. In addition to the aforementioned objectives, this paper will also address and explore the following key aspects:Identification and review of both the strength and weaknesses associated with test separators. By thoroughly examining these attributes, we can gain valuable insight into their effectiveness and potential areas for improvement. Exploration of alternative application of test separator and their impact on well testing efficiency. Real -World comparison will be provided to highlight the advantages and challenges associated with these alternative uses, offering a comprehensive understanding of their implications. Evaluation of the contribution that multiphase flows meters (MPFMs) can bring to the testing scenario and overall performance. By assessing the capabilities and potential benefits of MPFMs, we aim to provide a comprehensive picture of their role in enhancing testing procedures. Examination of the flow measurement uncertainties that can be expected from a test separator and their potential impact on reservoirs management performance. By understanding and quantifying these uncertainties, we can gain insight into how they may affect decision -making and optimization strategies in managing our materials assets effectively. Delving into the question of reconciling multiphase flow meter (MPFMs) with test separators. This analysis aims to inject a sense of realism into the world of managing our major material assets by explaining the challenges and opportunities associated with integrating and aligning these two measurement technologies. By addressing these crucial aspects, this paper strives to provide a comprehensive understanding of the complexities involved in managing our material assets, ultimately driving towards more informed decision-making and improved performance.

Methane is a greenhouse gas and identified as a key driver of near-term climate change. Bottom-up approaches estimate annual methane loss from US natural gas production and transport at 6 Tg, but recent studies suggest this may be an underestimate. To investigate this possibility, an equipment-based emissions inventory, using EPA emission factors, was developed to calculate methane emissions from oil and gas operations in the Delaware Basin, USA. Emission factors and activity data were then updated using contemporary and region-specific measurement data. The original inventory estimated emissions at 315 Gg CH4 y-1 (gas production-normalized rate of 0.6% loss), while the updated inventory estimated emissions of 1,500 Gg CH4 y-1 (2.8% loss). The largest changes resulted from large fugitive emissions from oil production (+430 Gg CH4 y-1), updating maintenance activity emissions (+214 Gg CH4 y-1), considering flaring inefficiency (+174 Gg CH4 y-1), and the inclusion of associated gas venting (+136 Gg CH4 y-1). This study suggests that a systematic underestimate probably exists in current bottom-up inventories and identifies sources currently missing or may be incorrect. We also strongly recommend that emission factors should be validated through direct comparison against measurement campaigns that include long-tail distributions typical of oil and gas activities.

Shrubs are a significant component of urban vegetation residing in parks, but they experience various influences of biotic and abiotic agents, among which aphids play an important role. In this work, the effect of aphid colonization on three shrub species in urban environment was examined. Fourteen parameters have been analyzed, describing photosynthetic pigment content and gas exchange to carbon, nitrogen, and hydrogen partition. While no significant effect of colonization was found on photosynthetic pigment parameters, the effect was significant on gas exchange parameters. The strongest effect aphid colonization achieved on nitrogen partition and C/N ratio, parameters that could be suggested in further similar studies. All parameters were classified in two groups according to principal component analysis, suggesting correlation between nitrogen and carbon content, C/N ratio, measured gas exchange parameters and chlorophyll a content. The ratio between net photosynthesis and dark respiration (A/K) was in the second group, suggesting that this parameter provide additional information on the effect of aphid colonization, and deserve special attention in further studies. There were differences in reaction of examined shrub species, where the strongest reaction by gross primary productivity (GPP) achieved Hybiscus syriacus, and by nitrogen partition and C/N ratio Spirea trilobata and Cydonia japonica.

A gas-hydrate method of CO₂ gas storage is one of the modern technology for reducing it emissions into the atmosphere. The breakup of gas bubbles by a shock wave is an actual area of scientific and technological research. However, it is little known that such research began in the late 1950s in the USSR. The article presents the main discoveries related to the destruction of gas bubbles in a liquid under the influence of a shock wave, made more than 60 years ago. Looking back: study the past to understand the present.

Several factors, such as internal algorithm, sensor technology, and obsolescence might skew outcomes when comparing different gas analysers measurements during CPET. Besides aerosol borne infectious disease are a source of contamination during cardiopulmonary exercise tests (CPET). Thus, the main aim of this study was to determine the agreement degree between the Quark RMR and the Jaeger Oxycon Pro, using an antibacterial filter with the latter. Forty-two participants (19-54 years old) performed two non-consecutive maximal graded exercise tests on a cycle-ergometer on two counterbalance and different days using the Oxycon Pro and the Quark RMR in a randomized order. Differences between devices were tested using a generalized linear model adjusted by Bonferroni, and correlation and agreement was assessed using Pearson’s correlation coefficient (R), intraclass coefficient correlation (ICC), Lin’s concordance correlation coefficient (CCC) and Bland-Altman plots. No significant differences were found between devices in any of metabolic or ventilatory parameters for cardiorespiratory fitness assessment (VO_2max: 3131.3±882.1 vs. 3189.8±894.8, p=0.071, VCO_2max: 3436.3±936.0 vs. 3550.3±1043.2, p=0.071, for Quark RMR and Oxycon Pro, respectively). However, Bland-Altman plots showed a trivial tendency towards Oxycon Pro overestimation relative to Quark RMR as air flow volume increases. Both devices showed strong correlation and high level of agreement during maximal and submaximal exercise intensities (Pearson’s R: 0.974 & 0.977; ICC: 0.985 & 0.987; Lin’s CCC: 0.971 & 0.974, for VO₂ and VCO₂, respectively). Therefore, providing consistency to CPET data comparison between both devices, and insight into whether the use of these metabolic carts could be interchangeable or combined when a single device cannot be used for CPET assessment.

The increase in carbon dioxide emissions has a significant impact on human society and the global environment. As the most abundant and cheap C1 resource, the conversion and utilization of carbon dioxide has received extensive attention from researchers. In many methods of carbon dioxide conversion and utilization, the reverse water gas conversion reaction is considered to be one of the most effective ways. In this paper, the research progress of reverse water gas conversion reaction in recent years is introduced.

Soluble noble metal salts are widely used for loading noble metals as nano-catalysts in many applications. In this paper, Pt-SnO2 composite nanoceramics were prepared from SnO2 nanoparticles and H2PtCl6 using two Pt-loading methods separately: For the solution reduction method, the H2PtCl6 solution was added to a suspension of SnO2 and zinc powder to form Pt on SnO2 nanoparticles; and for the impregnation method, Pt was formed from H2PtCl6 in the course of sintering. Although a series of samples prepared using both Pt loading methods showed a strong response to H2 at room temperature, the ones prepared using the solution reduction method exhibited much better room temperature hydrogen sensing characteristics. For two samples of 0.5 wt% Pt and sintered at 825°C, the response value for the sample prepared using the solution reduction method was 5300 to 1% H2-20% O2-N2, which was much larger than that of 150 for the sample prepared using the impregnation method. Samples prepared using the two Pt loading methods have similar microstructures as characterized by XRD, FESEM, EDS, TEM, and HRTEM. However, the residual chlorine content in those using the impregnation method was found to be higher than that using the solution reduction method through analysis. It is proposed that the striking difference in the room temperature hydrogen sensing characteristics among samples prepared using these two different Pt loading methods separately resulted from their different chlorine removal process. This study demonstrates the importance of a proper method in loading noble metals from their soluble salts as nano-catalysts in many applications.

Some of Iran's gas resources are known as sour gas because one of the major by-products of this gas is water. In fact, natural gas is combined with water vapor in underground reservoirs. In some areas, the amount of water vapor in natural gas is so high that it can be used as a source of drinking water. However, it should be noted that water vapor in natural gas may exacerbate corrosion in pipes and industrial equipment, and the combustion of more natural gas produces high temperatures that can lead to the production of nitrogen oxides (NOx), which They are the cause of air pollution. This is while the processed gas has a standard percentage composition in which the amount of water has the lowest position. The removal of moisture from natural gas is due to the need to prevent the reduction of the calorific value of the gas and also to purify the gas in order to achieve the necessary standards for delivering gas to petrochemicals, industries and domestic uses. The main goal of this research is to investigate the influencing parameters on zeolite TiO2 nanocomposite membranes in order to absorb moisture from gas. For this reason, with the construction of a TiZ-V membrane as a standard membrane, the result of the initial evaluation of a suitable membrane for gas dehumidification was made, and this membrane was placed as a standard for measuring the effect of the manufacturing parameters in a way that in each stage of membrane construction It was found that it was different from standard TiZ-V membrane only in terms of one parameter. This type of investigation made it possible to determine the effect of various effective parameters in membrane construction on efficiency. The findings showed that increasing the concentration of SiO2 has the greatest effect on increasing the water flux of the membrane. According to the other findings of this study, the effect of increasing the reaction time of the vapor phase carrier has been to reduce the process of paternity selectivity loss at higher pressures. Although due to the safety limitation of the equipment to measure the efficiency of the membrane at pressures higher than 7 bar, this measurement was not carried out, but charts were presented regarding the state of the water in the water, which were a measure of the superiority of the water in the water in comparison to the gas in the water, which is the higher water in the water It is an indicator of the appropriateness of the membrane's efficiency at its corresponding pressure, so that the examination of the difference between these two graphs shows the possibility of using the membrane at higher pressures

This work presents an LC resonant passive wireless gas sensor with a novel structure designed to mitigate the negative impact of substrate. The LC sensor antenna with the new structure and the reader antenna were designed and optimized utilizing HFSS software to improve the transfer efficiency. The superiority of the designed structure compared with the general ones is highlighted and verified. The change in the substrate capacitance has essentially no interference with the parameters to be measured of the LC sensor. The sensor with the new structure was prepared by combining etching and sputtering methods. The structure of the ZnO nanowires (NWs) was characterized to confirm their high purity and wurtzite crystal structure. The LC gas sensors demonstrated excellent wireless sensing performance including a low detection limit of 0.5 ppm NO2, high response of 1.058 and outstanding stability at 180 °C. The developed new sensor structure not only prevented interference from the substrate during gas sensing testing, but also expanded the choice of sensor substrates, playing a critical role in the development of sensors based on LC resonance principle.

Methane (CH4) emissions from agricultural sources make a significant contribution to the total anthropogenic greenhouse gas emissions that contribute to climate change. According to the International Panel on Climate Change (IPCC) guidelines for calculating greenhouse gas emissions, agriculture is responsible for approximately 10% of total CH4 emissions from anthropogenic sources. CH4 is mainly emitted from livestock farming, especially from cattle production during enteric fermentation and from manure. The article describes the results of multivariate statistical analyzes carried out on data collected in 1961–2020 based on the data for 30 countries with the largest cattle population. The trends of temporal changes in cattle population were evaluated and groups of countries with similar patterns in the study period were distinguished. Variables which are correlated with changes in the number of cattle were indicated. Forecasts of cattle population and CH4 emission related to cattle for the coming years are presented.

A total internal reflection photonic crystal fiber (PCF) based on hexagonal core is proposed for gas sensing in a specific wavelength range. The higher sensitivity and lower confinement loss were realized by the structure of the proposed PCF consists of two layers with circular holes rotated hexagonally around a core region and six slotted air-hole in the cladding based on numerical analysis. The simulation results show that the enhancement of the relative sensitivity has been done by enhancing the diameter of the hexagonal shape air-hole cladding (d1) and the hexagonal arranged holes around the central solid core (d0) in this design. Also, the confinement loss has been reduced by enhancing the ratio of length to width of slotted holes (l/w) and decreasing the cladding air-hole diameters (d1). As the refractive index increases, the wavelength shifts toward the long wavelength. And in a certain temperature range, the transmission characteristics of the device does not change with the temperature. The results are helpful for designing high performance PCF for gas sensing applications.

: We report on a direct correlation between macroscale structural variations and the gas sorption capacities of an ion gel. Here, we chose 1-ethyl-3-methylimidazolium bis(trifluoromethyl sulfonyl)imide ([Emim][TF2N]) and poly(vinylidene fluoride)-co-hexafluoropropylene (PVDF-HFP) as the ionic liquid and host polymer, respectively. The CO2 sorption in the thin films of IL-polymer was measured by the gravimetric method. The results of our experiment show that the trend of CO2 uptake of these mixtures is non-linearly correlated with the content of IL. Here we highlight the variation in the molecular structure of the polymers is the main reason behind the observed trend. The presented data suggest the possibility of using the composition of mixtures containing IL and polymers to realize a synergistic gain for gas sorption in these mixtures.

The previously developed models for fuel droplet heating and evaporation processes, mainly the Discrete Multi Component Model (DMCM), and Multi-Dimensional Quasi-Discrete Model (MDQDM) are investigated for the aerodynamic combustion simulation. The models have been recently improved, and generalised for a broad range of bio-fossil fuel blends so that the application areas are broadened with increased accuracy. The main distinctive features of these models are that they consider the impacts of species thermal conductivities and diffusivities within the droplets to account for the temperature gradient, transient diffusion of species and recirculation. A formulation of fuel surrogates is made, using the recently introduced model, referred to as ‘’Complex Fuel Surrogate Model (CFSM)’’ and analysing their heating, evaporation, and combustion characteristics. The CFSM is aimed to reduce the full composition of fuel to a much smaller number of components based on their mass fractions, and to formulate fuel surrogates. Such approach has provided a proof of concept with the implementation of the developed model into a commercial CFD code ANSYS-Fluent. A case study is made for the CFD modelling of gas-turbine engine using kerosene fuel surrogate. The surrogate is proposed using the CFSM. The model is implemented into ANSYS-Fluent via a user-defined function to provide the first full simulation of the combustion process. Detailed chemical mechanism is also implemented into ANSYS Chemkin for the combustion study.

Docked ships are a source of contamination for the city while they keep their engine working. Plumes emissions from large boats can carry a number of pollutants to the nearby cities causing a detrimental effect on the life quality and health of local citizens and ecosystems. A computational fluid dynamics model of the harbour area of Tromsø has been built in order to model the deposition of CO2 gas emitted by docked vessels within the city. The ground level distribution of the emitted gas has been obtained and the influence of the wind speed and direction, vessel chimney height, ambient temperature and exhaust gas temperature has been studied. The deposition range is found to be the largest when the wind speed is low. At high wind speeds, the deposition of pollutants along the wind direction is enhanced and spots of high pollutant concentration can be created. The simulation model is intended for the detailed study of the contamination in cities near the coast or an industrial pollutant source of any type of gas pollutants and can easily be extended for the study of particulate matter.

In this study, we test the performance of a compact gas chromatograph with photoionization detector (GC-PID) and optimize the configuration to detect ambient (sub-ppb) levels of benzene, toluene, ethylbenzene, and xylene isomers (BTEX). The GC-PID system was designed to serve as a relatively inexpensive (~$10k) and field-deployable air toxic screening tool alternative to conventional benchtop GCs. The instrument uses ambient air as a carrier gas, and consists of a Tenax-GR trap preconcentrator, a gas sample valve, two capillary columns, and a photoionization detector (PID) with a small footprint and low power requirement. The performance of the GC-PID has been evaluated in terms of system linearity and sensitivity in field conditions. The BTEX-GC system demonstrated the capacity to detect BTEX at levels as high as 500 ppb with a linear calibration range of 0-100 ppb. A detection limit lower than 1 ppb was found for all BTEX compounds with a sampling volume of 1 L. No significant drift in the instrument was observed. A time-varying calibration technique was established that requires minimal equipment for field operations and optimizes the sampling procedure for field measurements. With an analysis time of less than 15 minutes, the compact GC-PID is ideal for field deployment of background and polluted atmospheres for near-real time measurements of BTEX. The results highlight the application of the compact and portable GC-PID for community monitoring and screening of air toxics.

This paper presents a methodology for predictive and prescriptive analytics of complex engineering systems. The methodology is based on a combination of physics-based and data-driven modeling using machine learning techniques. Combining these approaches results in a set of reliable, fast, and continuously updating models for prescriptive analytics. The methodology is demonstrated with a case study of a jet-engine power plant preventive maintenance and diagnostics of its flame tube.

Solid porous materials, like zeolites, have been widely used in a variety of fields such as size and shape-selective absorption/separation and catalysis because of their porosity. But there are few liquid materials exhibit permanent porosity. Porous liquids are a novel material that combine the properties of fluidity and permanent porosity. It has potential applications in many fields such as gas separation, storage and transport. Herein, we report a novel Type 1 porous liquid prepared based on Silicalite-1. The pore size of this porous liquid was determined by positron annihilation lifetime spectroscopy (PALS), and the CO2 capacities was determined by the intelligent gravimetric analyser (IGA). The unique properties of this porous liquid can promote its application in many fields such as gas storage and transport.

The aim of this paper is the presentation of an analytical model of insulator flashover and its application for air at atmospheric pressure and pressurized SF6. After a review of the main existing models in air and compressed gases, we develop a relationship of flashover voltage on the basis of an electrical equivalent circuit and the thermal properties of the discharge. The model includes the discharge resistance, the insulator impedance, and the gas interface impedance. The application of this model to a cylindrical resin-epoxy insulators in air medium and SF6 gas with different pressures gives results close to the experimental measurements.

There is great potential for reducing greenhouse gas emissions (GHGE) from public sector meals. This paper aimed to develop a strategy for reducing GHGE in the Swedish school food supply without compromising nutritional adequacy, affordability, and cultural acceptability. Amounts, prices and GHGE-values for all foods and drinks supplied to three schools over one year were gathered. The amounts were optimized by linear programming. Four nutritionally adequate models were developed: Model 1 minimized GHGE while constraining relative deviation (RD) from observed food supply; Model 2 minimized total RD while imposing stepwise GHGE reductions; Model 3 additionally constrained RD for individual foods to an upper and lower limit; and Model 4 further controlled how ratios between food groups could deviate. Models 1 and 2 reduced GHGE by up to 95% but omitted entire food categories or increased the supply of some individual foods by more than 800% and were deemed unfeasible. Model 3 reduced GHGE by up to 60%, excluded no foods, avoided high RDs of individual foods, but resulted in large changes in food group ratios. Model 4 limited changes in food group ratios but resulted in a higher number of foods deviating from the observed supply and limited the potential of reducing GHGE. Cost was reduced in almost all solutions. An omnivorous, nutritionally adequate, and affordable school food supply, with considerably lower GHGE is achievable with moderate changes to the observed food supply. Trade-offs will always have to be made between achieving GHGE reductions and preserving similarity to the current supply.

Innovations and improvements in hydraulic fracturing and horizontal well technologies have contributed to the success of the shale gas industry; however, the industry is also challenged by freshwater use and environmental health issues. Increasing water impact makes precise quantification of water consumption important. The objective in this study was to better understand water sustainability and availability of the projected shale gas from 2018 to 2030 in the Weiyuan play, China. The water footprint framework was used to quantify the potential water use and environmental impacts on different time scales. The results showed that the water use per well ranged from 11351.3 to 60664.73 m3, with a median of 36013.94 m3, totaling ~3.44 Mm3 for 97 wells. Yearly evaluation results showed that the gray water footprint was the main contributor and accounted for 83.82% to 96.76%, which was dependent on different scenarios of treatment percentages. The monthly environmental impact results indicated that the annual streamflow statistics were more likely to prevent water withdrawal. Water quality issues may be alleviated through recycling and retreatment measures that improve current waste water management strategies. Resource regulators should manage their water resources by matching water demand to water availability or replenishment.

In this work, a tailored extreme learning machine (ELM) algorithm to enhance the overall robustness of gas analyzer based on the tunable diode laser absorption spectroscopy (TDLAS) method is presented. The ELM model is tailored through activation function selection, input weight and bias searching, and cross validation method to address the analyzer robustness issues for industrial process analysis field application. The two particular issues are the inaccurate gas concentration measurement caused by the process gas background components variation, and the inaccurate spectra shift calculation caused by spectral interference. By using our algorithm, the concentration error is reduced by one order of magnitude over a much larger stream pressure and component range compared with that obtained by classical least square (CLS) fitting methods based on reference curves. Additionally, it is shown that with our algorithm, the wavelength shift accuracy is improved to less than 1 count over 1000 counts spectra length. In order to test the viability of our algorithm, a trace ethylene (C₂H₄) TDLAS analyzer with coexisting methane was implemented, and its experimental measurements support analyzing robustness enhancement effect.

Here is shown method for the hydraulic solution of a looped gas-pipeline networks. Calculation of presented network is done according to principles of Hardy Cross method. The optimization was carried out by iteration of the pipes diameters, node consumptions are known and flow velocities through pipes have to stand below certain values. Accent is on determination of appropriate friction factor, and on selection of representative equation for natural gas flow under presented conditions in the network. Inappropriate usage of friction factor, equally as inappropriate usage of gas flow equation can lead to inaccurate final results. Here is shown new facts in comparison to previous calculation of gas distribution network in Kragujevac, Serbia which is done in 1994. After the implementation, measurements in situ have performed, and real measured values deviate from calculated. Causes for these errors are investigated, and improved and more accurate procedure is shown.

According to the operation conditions of time unlimited passive containment heat removal system (TUPAC), a separate effect experiment facility was established to investigate the heat transfer performance of steam condensation in presence of non-condensable gas. The effect of wall subcooling temperature, total pressure and mass fraction of the air on heat transfer process was analyzed. The heat transfer model was also developed. The results showed that the heat transfer coefficient decreased with the rising of subcooling temperature, the decreasing of the total pressure and air mass fraction. It was revealed that Dehbi’s correlation predicted the heat transfer coefficient conservatively, especially in the low pressure and low temperature region. The novel correlation was fitted by the data obtained in the following range: 0.20~0.45 MPa in pressure, 20% ~ 80% in mass fraction, 15°C ~ 45°C in temperature. The discrepancy of the correlation and experiment data was with ±20%.

Current education in biology is devoid of mathematics in many countries, probably because many relevant biological processes are explained from a qualitative point of view rather than addressing the quantitative aspects of these phenomena. Here, we employ a case study from the yeast physiology to illustrate the importance of numeracy skills for a deeper understanding of relevant biological problems. Yeast anaerobic growth on sugars is a widespread process as it is the basis for beer, bread, and winemaking and it is much akin to lactic acid fermentation in muscle cells in response to an increased energy demand. To study the physiology of yeasts under controlled conditions and being able to compare the results quantitatively, one ought to perform measurements and calculations involving concentrations of oxygen, biomass, and organic compounds. To set-up an “anaerobic” culture of Saccharomyces cerevisiae in a defined medium, one needs to calculate how much oxygen must enter the cultivation system, to meet the requirements for ergosterol and oleic acid biosyntheses, both of which require oxygen. Using basic physicochemical principles and simple mathematical skills, students will be able to compute the oxygen requirement for yeast growth under such “anaerobic” conditions.

Transport biofuels derived from biogenic material are used for substituting fossil fuels, thereby abating greenhouse gas (GHG) emissions. Numerous competing conversion options exist to produce biofuels, with differing GHG emissions and costs. In this paper analysis and modelling of the long-term development of GHG abatement and relative GHG abatement cost competitiveness between crop-based biofuels in Germany is carried out. Presently dominant conventional biofuels and advanced liquid biofuels were found not to be competitive compared to the substantially higher yielding options available: sugar beet based ethanol for the short to medium term least-cost option and Substitute Natural Gas (SNG) for the medium to long term. The competitiveness of SNG was found to depend highly on the emissions development of the power mix. Silage maize based biomethane was found competitive on a land area basis, but not on an energetic basis. Due to land limitations as well as cost and GHG uncertainty, a stronger focus on the land use of crop-based biofuels should be laid in policy.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

Downwind odor characteristics can be very different depending upon the size of the upwind point-source, interim topography, and wind conditions. At one extreme, the downwind odor plume from a relatively large, confined animal feeding operation (CAFO), located on a flat open plain and under stable, near-straight-line wind conditions can be rather broad, sustained and predictable relative to a fixed receptor site downwind. In contrast, the plume from a small point-source (e.g., a roof vent stack) located on irregular topography and under rapidly shifting wind conditions can be intermittent and fleeting. These transient odor events can be surprisingly intense and offensive, in spite of their fleeting occurrence and perception. This work reports on efforts to optimize an environmental odor sampling strategy, which is optimized for the challenges of (1) sampling of such transient odor 'spikes' and (2) the prioritization of odors/odorants from multiple, closely co-located point-sources, under such transient event conditions. Protocol refinement has emerged by way of 2 environmental odor assessment projects which have been undertaken on behalf of the Missouri Department of Natural Resources. The challenge of transient odor events has been mitigated utilizing rapid, odor cued whole-air grab capture sampling into metalized-FEP gas sampling bags, followed by immediate adsorption transfer onto SPME fibers or sorbent tubes for stabilization during the shipment and storage interval between collection and final analysis. Initial results demonstrated approximately 11 fold increases in target odorant yields for 900 mL sorbent tube transfers from 2-3 second 'burst' odor event bag-captures, as compared to equivalent direct collections at the same downwind receptor location but during perceived (stable) odor 'lull' periods. Results-to-date targeting refinement and field trials of this integrated environmental odor assessment strategy are presented. Preliminary application targeting general odor sampling and point-source differentiation utilizing tracer gases is also presented.

This paper describes a novel concept of producing energy efficient ”Maroon enriched natural gas “ and then Pink hydrogen” from any hydrocarbon base. The key idea is the extraction of hydrogen from water in addition to that from the hydrocarbon in an optimal fashion. This has the benefit of higher water vapor to CO2 exhaust ratio than conventional carbonaceous fuels when generating energy via combustion, a prudent step in achieving Netzero goals in a shorter time, and creating energy independence in most places.. The process of production makes concentrated CO₂ available for use and or sequestration. The process also maximizes use of renewable electricity in hydrogen generation, and maximizes use of existing infrastructure, with a minimum capital cost by energy recycle in the process. The process design applies sound thermodynamic principles which evolved during the nineteenth century, and mimics the geochemical processes going on in some of the natural 'colorless hydrogen'.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

An analysis of the features of measurements and correction of phase distortions in optical waves propagating in the atmosphere at various levels of turbulence was performed. It is shown that with increasing intensity fluctuations, the limiting capabilities of phase correction decrease, and the phase of an optical wave that has passed through a turbulence layer consists of two components: potential and vortex. It was found that even in the region of weak fluctuations there is an overlap of spectral filtering functions for intensity and phase fluctuations. Areas of turbulence inhomogeneities have been identified that will have mutual influence and negatively affect the operation of the phase meter. It is noted that correlation functions, both phase and intensity, are less susceptible to this compared to structural functions. The results of experimental studies of the reconstruction of the wavefront of laser radiation distorted by atmospheric turbulence using a Shack-Hartmann wavefront sensor during vignetting and central screening of the entrance pupil of the optical system are presented. Studies have been carried out on the propagation of laser radiation along a horizontal atmospheric path for various levels of turbulence. The results are analyzed in terms of Zernike polynomials.

Motivated by the increasing need of optimised micro-devices for droplets production in medical and biological applications, this paper introduces an integrated approach for the study of the liquid-liquid droplet creation in flow-focusing micro cross-junctions. The micro-junction considered is characterised by a restriction of the channels cross-sections in the junction, which has the function of focusing the flow in the region of the droplet formation. The problem is studied numerically in OpenFOAM environment and validated by the comparison with experimental results obtained by high-speed camera images and micro-PIV measurements. The analysis of the forces acting on the dispersed phase during the droplet formation and the diameter of the droplets obtained numerically are considered for the development of a model of the droplet breakup under the squeezing regime. On the basis of energy balancing during the breakup, a relation between interfacial tension, the size of the cross-sections in the junction, and the time interval needed for droplet creation is obtained, which yields a novel correlation between the dimensionless length of the droplet and the dimensionless flow rate. This correlation is general and can be used to predict the droplet diameters produced by similar micro-junctions with different aspect ratios and extended to different geometries of flow-focusing micro-junctions.

(1) Background: Myelodysplastic syndromes (MDS) are a group of diseases that affect the morphology and function of neutrophils. Rapid diagnosis of MDS is crucial for the initiation of treatment that can vastly improve disease outcome. (2) methods: In this work, we present a new approach for detecting morphological differences between neutrophils isolated from blood samples of high risk MDS patients and that for patients and blood bank donors (BBDs). First, using fluorescent flow cytometry CD66b positive cells were stained with 2′,7′-dichlorofluorescin diacetate (DCF) and Hoechst. Secondly, we imaged the cells using interferometric phase microscopy (IPM) without utilizing cell staining. (3) Results: flow cytometry results show MDS patients present different dispersion patterns compared to BBDs. BBDs present two distinct subpopulations (one of these are the H cells constituting 16% for neutrophils) whereas MDS patients present only 4% of this subpopulation. IPM results are consistent with this pattern: ~20% of BBDs neutrophils were characterized as H cells and whereas MDS patients present only ~4% of these cells. (5) Conclusion- IPM can be utilized for diagnosis of complex hematological pathologies such as MDS.

New TLC-densitometric method have been developed for the identification and quantification of paracetamol (PA), propyphenazone (PP) and caffeine (C) of Saridon tablets using the NP-TLC technique combined with densitometry. This method allows for the simultaneous determination of PA, PP, and C in the same sample. Among all tested chromatographic conditions, the mixture consisting of chloroform + toluene + ethyl acetate + ethanol + acetic acid (18:18:7.5:5.0:0.3, v/v) and silica gel 60F254 plate proved to be the most effective for the separation of three tested active pharmaceutical ingredients (APIs) and substances related to paracetamol. The fully validation of the proposed NP-TLC method proves that it is specific, precise, accurate, robust and sensitive. The percentage content in relation to the content declared by the manufacturer is for propyphenazone 99.8%, paracetamol 101.6% and caffeine 100.8%, which are in accordance with pharmacopoeial requirements. The results presented indicate the possibility of using the developed method in the routine control of pharmaceutical preparations containing these APIs. The proposed method is economical and more sensitive compared to the previously proposed planar methods for the simultaneously determination of PA, PP and CAPIs. Will be an What is more, the presented method may be anaxcellent excellent economical alternative when HPLC method is unavailable for such determination.