Introduction: Galectin-13 (Gal-13) is predominantly produced by the syncytiotrophoblast, while laeverin is expressed on the outgrowing extravillous trophoblast, and both are thought to be biomarkers of preeclampsia. The aim of this study was to assess the correlation between concentrations of Gal-13 and laeverin measured in maternal serum and amniotic fluid at 16-22 weeks of gestation and the sonographic assessment of the fetoplacental measurements. Materials and methods: Fetal biometric data, and placental volume and perfusion indices were measured in 62 singleton pregnancies. Serum and amniotic levels of Gal-13 and laeverin levels were measured using a sandwich ELISA. Results: Both amniotic fluid and serum Gal-13 levels expressed a negative correlation to the plasma laeverin level in mid-pregnancy. Serum laeverin level correlated positively with the gestational length at delivery (β=0.39, p

Abrasive Water Jet Machining (AWJM) is a non-conventional machining process that, unlike other methods, is deemed superior because of its applicability, versatility, and no heat-affected zones in the target material. The main objective of this paper was to develop a cheap, practical model for a low-pressure water jet cutting machine and provide some empirical test data for cutting delicate materials. Proper design calculations were performed and are included for both the water jet machine and the two-axis numerical control. Finite Element Analysis results validate the structural integrity of beams and columns in AWJM. Computational Fluid Dynamic analysis of the nozzle shows good agreement with the theoretical calculations regarding the pressure and velocity of the water-abrasive mixture exiting the nozzle. Modal analysis in ANSYS was done to mitigate potential failure due to resonance induced by vibrations. Limited testing on various thicknesses of polystyrene foam ranging from 1-5 mm thickness and rubber sheet of 1 mm thickness showed that even low pressure of 25-30 bar was sufficient to produce a kerf without any burr. However, extensive testing to report optimized parameters like nozzle transverse speed, standoff distance, abrasive flow rate, etc for working at low-pressure ranges is still a consideration for future investigation.

The demographic profile of patients transitioning from chronic kidney disease to renal replacement therapy is changing, with a higher prevalence of aging patients with multiple comorbidities such as diabetes mellitus and heart failure. Cardiovascular disease remains the leading cause of mortality in this population, exacerbated by the cardiovascular stress imposed by the HD procedure. The first year after transitioning to hemodialysis is associated with increased risks of hospitalization and mortality, particularly within the first 90–120 days, with greater vulnerability observed among the elderly. This review, based on data from clinics of Fresenius Medical Care Europe, Middle East, and Africa NephroCare, aims to optimize hemodialysis procedures to reduce mortality risk in stable incident and prevalent patients. It addresses critical aspects such as treatment duration, frequency, choice of dialysis membrane, dialysate composition, blood and dialysate flow rates, electrolyte composition, temperature control, target weight management, dialysis adequacy, and additional protocols, with a focus on mitigating prevalent intradialytic complications, particularly intradialytic hypotension prevention.

This manuscript presents a novel approach to estimating the potential within Schrödinger equations, with a particular focus on applications to the Navier-Stokes problem in fluid dynamics. By establishing new theoretical estimates, we delve into the intricate dynamics of fluid flow, aiming to unveil previously obscured aspects of the Navier-Stokes equations. Through a rigorous mathematical framework, we explore how these new potential estimates can provide a fresh perspective on fluid mechanics, contributing to the ongoing quest to solve some of its most persistent challenges.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

The paper presents a new type of hydraulic clutch operating with magnetorheological (MR) fluids and the results achieved from both theoretical analysis and experimental measurement. The hy-draulic clutch system of its own design with MR working fluid and a rotating magnetic field lo-cated is designed. The principle of this clutch is to use a rotating magnetic field created by an al-ternating current electromagnet to set the MR fluid in motion. In the tests of the hydraulic clutch with a rotating magnetic field, MR fluid produced on their own, consisting of solid iron particles of various diameters mixed with a silicone oil, are used as working fluids. The rheological properties of MR fluids are assessed on the basis of tests carried out with a Brookfield DV2T rheometer equipped with a magnetic device for generating the magnetic field of its own design. The char-acteristics of the hydraulic clutch with MR working fluid and the rotating magnetic field are tested on a specially built test stand. As a result of the research, it has been found that the torque transmitted by the clutch is the greater, the higher the rotational speed of the magnetic field and the lower the rotational speed of the beaker in which the working fluid is placed, and that the greatest torque occurs for the working fluid with the highest iron content. Based on the analysis of the structure and characteristics of the clutch in which the magnetic field is used, it has been shown that the design of the developed clutch is similar to that of an induction clutch, and its characteristics correspond to the characteristics of the eddy current clutch. Therefore, the proposed new clutch working with MR fluid and the rotating magnetic field can be applied to stationary power transmission system similarly to an eddy current clutch.

Sweat rate and electrolyte losses have a large inter-individual variability, a personalized approach to hydration can overcome this issue to meet an individual’s needs. This study aimed to investigate the effects of personalized hydration strategy (PHS) on fluid balance and intermittent exercise performance. Twelve participants conducted 11 laboratory visits including a VO2max test and two 5-day trial arms under normothermic (NOR) or hyperthermic (HYP) environmental conditions. Each arm began with 3-day of familiarization exercise following by two random exercise trials with a either PHS or control (CON). Then, participants crossed-over to the second arm for: NOR+PHS, NOR+CON, HYP+PHS, and HYP+CON. The PHS was prescribed according to participants’ fluid and sweat sodium losses. CON drank ad-libitum of commercially-available electrolyte solution. Exercise trials consisted of two phases: 1) 45min constant workload; 2) high-intensity intermittent exercise (HIIT) until exhaustion. PHS had a significantly greater fluid intake compared to CON. HYP+CON produced the lowest sweat sodium concentration. HYP+PHS had a lower thirst perception and a longer HIIT compared to HYP+CON. Thus, PHS reinforces fluid intake and successfully optimizes hydration status, regardless of environmental conditions. PHS may be or is an important factor to preventing negative physiological consequences during high-intensity exercise in the heat.

Even though inhalation dosimetry is determined by three factors (i.e., breathing, aerosols, and the respiratory tract), the first two categories have been more widely studied than the last. Both breathing and aerosols are quantitative variables that can be easily changed, while respiratory airway morphologies are difficult to reconstruct, modify, and quantify. Despite several methods are available for model reconstruction and modification, developing an anatomically accurate airway model and morphing it to various physiological conditions remains labor-intensive and technically challenging. The objective of this study is to explore the feasibility of using an adjoint-CFD model to understand airway shape effects on vapor deposition and control vapor flux into the lung. A mouth-throat model was used, with the shape of the mouth and tongue being automatically varied via adjoint morphing, and the vapor transport being simulated using ANSYS Fluent coupled with a wall absorption model. Two chemicals with varying adsorption rates, Acetaldehyde and Benzene, were considered, which exhibited large differences in dosimetry sensitivity to airway shapes. For both chemicals, large shape deformations were explored to find the maximal possible morphing; both the maximal and intermediate deformations were simulated for morphology parametric studies. Results show that changing the mouth-tongue shape can alter the oral filtration by 3.2% for Acetaldehyde and 0.27% for Benzene under a given inhalation condition. This study demonstrates that the hybrid adjoint-CFD approach can be a practical and efficient method to investigate morphology-associated variability in inhalation dosimetry of vapors and nanomedicines.

Hemodynamic relevance of differently located stenoses of the internal jugular veins remains undetermined. It particularly concerns nozzle-like strictures in the upper parts of these veins and stenotic jugular valves located at the end of this vein. This study was aimed at understanding flow disturbances caused by such stenoses. Computational fluid dynamics software, Flowsquare+, was used. We constructed 3-dimensional models of venous outflow, comprising two alternative routes: tube representing the internal jugular vein and irregular network representing the vertebral veins. At the beginning of the tube representing the internal jugular vein, differently-shaped and sized short strictures, representing nozzle-like strictures were built in. At the end of this tube, differently-shaped membranes, representing the jugular valve, were built in. With the use of computational fluid dynamics modeling, we studied how these two obstacles influenced the outflow. We found that the most relevant outflow disturbances were evoked by nozzle-like strictures in the upper part of the internal jugular vein that were either small, long or asymmetrically positioned. Very tight stenotic valves and septum-like malformed valve were equally hemodynamically relevant. These findings suggest that both upper and lower strictures of the internal jugular vein can be of clinical significance.

Fractional flow reserve (FFR) is well recognized as a gold standard measure for the estimation of functional coronary stenosis. Technological progressions in image processing have empowered the reconstruction of three-dimensional models of the coronary arteries via both non-invasive imaging modalities, such as Coronary Computed Tomography Angiography (CCTA), and invasive coronary angiography or intravascular imaging. The application of computational fluid dynamics (CFD) techniques to coronary 3D anatomical models allows the virtual evaluation of the hemodynamic significance of a coronary lesion with high diagnostic accuracy in comparison to the invasive FFR using pressure wires. These opportunities providing hemodynamic information based on anatomy have given rise to a new era of functional angiography and coronary imaging. However, further validations are needed to overcome several scientific and computational challenges before these methods are applied in everyday clinical practice. This review aims to present all the data on the studies and methodologies that have been presented for the virtual estimation of FFR, and the diagnostic execution of the virtual tools for the hemodynamic assessment of coronary lesions compared to the invasive FFR.

This work is aimed at investigating the capabilities and limits of the mid-fidelity numerical solver DUST for the evaluation of wind turbines aerodynamic performance. In particular, this study was conducted by analysing the benchmarks NREL- 5MW and Phase VI wind turbines, widely investigated in literature by from experimental and numerical activities. The work started by simulating simpler configuration of the NREL- 5MW turbine to progressively integrate complexities such as shaft tilt, cone effects and yawed inflow conditions, offering a detailed portrayal of their collective impact on turbine performance. A particular focus was then given to the evaluation of aerodynamic responses from the tower and nacelle, as well as aerodynamic behavior in yawed inflow condition, crucial for optimizing farm layouts. In the second phase, the work was focused on NREL Phase VI turbine due to the availability of experimental data on this benchmark case. Comparison of DUST simulations results with both experimental data and high-fidelity CFD tools shows the robustness and adaptability of this mid-fidelity solver for this applications, thus opening a new scenario for the use of such mid-fidelity tools for the preliminary design of novel wind turbines configurations or complex environments as wind farms, characterised by robust interactional aerodynamics.

A positive fluid balance may evolve to fluid overload and associate with organ dysfunctions, weaning difficulties, and increased mortality in ICU patients. We explored whether individualized fluid management, assessing fluid-responsiveness via passive leg-raising maneuver (PLR) before spontaneous breathing trial (SBT) associated with less extubation failure in ventilated patients with high fluid balance, admitted to the ICU after liver transplantation (LT). We recruited 15 LT patients in 2023. Postoperative fluid balance was +4476 [3697,5722] mL. PLRs were conducted at ICU admission (T1) and pre-SBT (T2). Cardiac index (CI) changes were recorded before and after SBT (T3). Seven patients were fluid responsive at T1, and 12 at T2. No significant differences occurred in hemodynamic, respiratory, and perfusion parameters between fluid-responsive and fluid-unresponsive patients at any time. Fluid-responsive patients at T1 and T2 increased their CI during SBT from 3.1 [2.8,3.7] to 3.7 [3.4,4.1] mL/min/m2 (p= 0.045). All fluid-responsive patients at T2 were extubated after SBT and consolidated extubation. Two out of three of fluid-unresponsive patients experienced weaning difficulties. We concluded that fluid-responsive patients post-LT may start weaning earlier and achieve successful extubation despite high postoperative fluid balance. This highlights the profound impact of personalized assessment of cardiovascular state on critical surgical patients.

This study explores the significance of active suspension systems for vehicles with lower chassis compared to conventional ones, aiming at the development of future automobiles. Conventional linear MR (Magneto-Rheological) dampers were found inadequate in ensuring sufficient vibration control because the vehicle's chassis becomes lowered in the unmanned vehicles or purposed based vehicles. As an alternative, a rotary type of MR damper is proposed in this work. The proposed damper is designed based on pre-specified design parameters through mathematical modeling and magnetic field analyses. Subsequently, a prototype of the rotary MR damper identical to the design is fabricated, and effectiveness is shown through experimental investigations. In configuring the experiments, a proportional-integral (PI) controller is employed for current control to reduce the response time of the damper. The results presented in this work provides useful guidelines to develop a new type of MR damper applicable to various types of future vehicles’ suspension systems with low distance from the tire to the body floor.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

This study presents an extensive collection of data on the aerodynamic behavior at a low Reynolds number and geometric coefficients for 2900 airfoils obtained through the class shape transformation (CST) method. By employing a verified OpenFOAM-based CFD simulation framework, lift and drag coefficients were determined at a Reynolds number of 10^5. Considering the limited availability of data on low Reynolds number airfoils, this dataset is invaluable for a wide range of applications, including unmanned aerial vehicles (UAVs) and wind turbines. Additionally, the study offers a method for automating CFD simulations that could be applied to obtain aerodynamic coefficients at higher Reynolds numbers. The breadth of this dataset also supports the enhancement and creation of machine learning (ML) models, further advancing research into the aerodynamics of airfoils and lifting surfaces.

In this paper is proposed an analytical technique which can be used to obtain the forced response of a cantilevered tube conveying fluid. Considering the pipe subjected to an arbitrary harmonic force either distributed or concentrated, an analytical solution is found using Green’s function method. The solution obtained of the closed form satisfies the differential equations in a classical sense. The presented method giving the exact solutions is more precise than the classical eigenfunction expansion or Galerkin’s method with no need to the eigenfunctions or eigenvalues.

While the underwater submersible encounters internal solitary wave (ISW), its loadings and motions would be seriously disturbed. To investigate the interaction effect between the suspended submersible and ISW, a three dimensional ISW-submersible interaction numerical model was established based on the Computational Fluid Dynamics (CFD) method. The generation and propagation of ISW was simulated in a two-layer fluid numerical wave tank according to the eKdV theory. The standard operation equation of submersible was introduced to simulate the six degree of freedom (6DoF) motions of submersible combined with the overset dynamic mesh method. The motion simulation method of submersible was effectively validated by comparing with published experimental results on the motion responses of the slender body under the ISW. Based on the constructed numerical model, the dynamic mechanism between the suspended submersible and ISW were studied, and the effects of the initial submerged depths and the ISW amplitudes on the dynamic responses of the submersible were revealed. According to the numerical results, the motions of the submersible have been significantly determined by its initial submerged depths. The submersible located above the ISW interface has a significant motion along the propagation direction of ISW and its motion trajectory resembles a counterclockwise semi ellipse. The motions of the submersible located below the ISW interface follows with the trace of the lower layer fluid which presented as an unclosed clockwise ellipse. The corresponding motions of the submersible would be increased as the increase of the ISW amplitudes.

The emergence of electric vehicles has brought new issues such as the problem of rolling element bearings (REBs) operating at high speeds. Losses due to these components in mechanical transmissions are a key issue and must therefore be taken into account right from the design stage of these systems. Among these losses, the one induced by the motion of rolling elements , known as drag loss, becomes predominant in high-speed REBs. Although an experimental approach is still possible, it is difficult to isolate this loss in order to study it properly. A numerical approach based on CFD is therefore a possible way forward, even if other issues arise. The aim of this article is to study the ability of such an approach to correctly estimate the drag coefficient associated with the motion of rolling elements. The influence of the numerical domain extension, the mesh refinement, the simplification of the ring shape and the presence of the cage, on the values of the drag coefficient is presented. While it seems possible to compromise on the calculation domain and mesh size, it appears that the other parameters must be taken into account as much as possible to obtain realistic results.

Peritoneal fluid is an ovarian exudate from the growing follicle or corpus luteum. Therefore, the free concentrations of estrogens and progesterone are always much higher than in plasma, especially after ovulation. The peritoneum is not vascularised, and peritoneal implants and the superficial portion of deep endometriosis are likely influenced mainly by peritoneal fluid. Follicular phase progesterone concentrations are as high as during the luteal phase in plasma. This explains that most peritoneal implants are rarely proliferative and out of phase with the endometrium. From some 5 mm of depth onwards, endometriosis is rather influenced by plasma hormone concentra-tions, and the deeper parts can be proliferative as the endometrium. Because of these progesterone concentrations, progesterone resistance has to be postulated, permitting endometriosis lesions to initiate and develop. This opens the discussion of whether endometriosis is similar to the basal endometrium. These peritoneal fluid concentrations are important to understand the natural history and medical therapy of endometriosis. Most medical therapies decrease ovarian function and affect peritoneal fluid steroid hormone concentrations. It is suggested that the efficacy of medical therapy for endometriosis-associated pain is a consequence of the decreased estrogen concentrations in the peritoneal cavity and that the local effect of progestins may not be determinant for pain relief. If this is true, a history of endometriosis should not be considered a contraindication for hormone re-placement therapy.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

To establish simulated micro-gravity conditions, biological organisms are placed on a simulated microgravity system, which primarily rotate in two or three dimensions and rely on slow sedimentation with latency to detect gravity. Fluid dynamics arise as a consequence of rotation of the chambers with in which the cells are filled. To minimize the effects of centrifugal forces, it is necessary to position the samples as close to the center of rotation as possible. Strong shear forces and velocities within the vessel can have an adverse impact on cells, making this a critical topic in cell biology. During experimental investigation, this specific phenomenon is not apparent, but numerical modelling readily illustrates and is not widely analyzed in literature's. Furthermore, bulk flask are frequently employed on random positioning machines (RPM), not merely because they demand a substantial quantity of reagents. The flask presented in the study can be easily developed and fitted in conventional cell culture plates containing medium and reagents similar to those used in ground experiments, thus allowing it to remain close to the center of rotation. In the present study, a series of fluid dynamics simulations are performed to examine the impact of shear forces within the microvessel presented under varying conditions using a foreign medium condition, and these results are compared with existing vessels by observing the effects of shear forces and maximum velocity zones.

EV transmissions operate at high speeds, upto 30,000 rpm. High speed operation puts higher demands on bearings, seals, and gears. Bearings in EV transmissions are prone to electrically induced bearing damage and may exhibit signs of pitting and fluting. Surface-initiated rolling contact fatigue is another common problem gaining increased attention lately. Most EV transmissions require a coupling between an oil-lubricated gearbox to an electrical motor that runs with minimal lubrication at very high rpm. High mechanical and thermal stresses the seals are exposed to under starved lubrication conditions have a detrimental impact on their service life. Hence, proper lubrication is critical. In general, EV transmission fluids call for a somewhat different spectrum of properties compared to conventional ATF. Gear tribology simulations open new ways to the design and optimization of lubrication for EV transmissions. Additionally, such simulations can also provide valuable insights into the effects of different oil properties on cooling and lubrication efficiencies, thereby helping in matching the lubricant and hardware characteristics for optimal performance. In the present communication, we demonstrate the effects of different lubricants and surface finishing technologies on the tribology of high-speed gears using tribological tests and advanced thermal elastohydrodynamic (TEHD) simulations. Important roles of lubricity additives and surface finish optimization are highlighted in conjunction with a move towards ultralow viscosity EV transmission fluids.

Wall Shear Stress (WSS) abnormalities in carotid artery blood flow are key hemodynamic factors leading to arterial endothelial damage, atherosclerotic plaque formation, and carotid artery stenosis. Precise simulation of carotid artery blood flow WSS in vitro play an important role in understanding the underlying hemodynamic mechanism of carotid artery stenosis. This study presents a design for a microfluidic cell culture chamber with a variable cross-section and a step structure, leveraging microfluidic technology and principles of fluid dynamics. We propose an optimization strategy for microchannel dimensions based on Computational Fluid Dynamics (CFD) simulations. This strategy aims to replicate the distinct WSS waveform features found at various locations within the carotid bifurcation as observed in vivo. Our simulations indicate that with a step height of 0.09 mm, a width of 4 mm for the initial segment, and 5 mm for the subsequent wider channel, the device can effectively model the characteristics of low oscillatory WSS seen at sites of carotid sinus stenosis. Furthermore, it accurately represents the high-magnitude pulsatile WSS waveforms in the more uniform arterial sections downstream of the carotid sinus. The study also reveals that vortex formation and variations in low oscillatory WSS within the stepped section of the microchannel correlate with the step's height and width, as well as with the dimensions of the wider channel section. An increase in step width leads to a decrease in both the vortex area and the magnitude of negative WSS oscillations. When the step height is less than 0.03 mm, vortex formation is inhibited, challenging the simulation of low oscillatory WSS patterns. The variable cross-section microfluidic channel developed in this study provides a platform for simulating carotid artery WSS waveforms and facilitates research into the interplay between low oscillatory WSS at sites of carotid sinus stenosis and arterial endothelial dysfunction.

We introduce the linear subgroup of volume-preserving diffeomorphism as the underlying symmetry to construct an action within the effective field theory framework and the Schwinger-Keldish formalism. The formulated action is posited to effectively incorporate dissipative effects into the Navier-Stokes equations.

This paper provides the first-time ever analytic modelling for Pointwise Stationary Fluid Flow Approximation(PSFFA) model of the non-stationary

Introduction: The trophoblast derived angiogenic factors are considered to play an important role in the pathophysiology of various complications of pregnancy. The aim of this study was to establish relationship between concentrations of soluble Human Leukocyte Antigen-G (sHLA-G) in maternal serum and amniotic fluid at 16-22 weeks of gestation and the sonographic measurements of the fetal and placental growth. Materials and methods: sHLA-G in serum and amniotic fluid, as well as fetal biometric data and placental volume and perfusion indices were determined in 41 uncomplicated singleton pregnancies. Results: The sHLA-G levels were unchanged both in amniotic fluid and in serum during mid-pregnancy. The sHLA-G level in serum correlated positively with amniotic sHLA-G level (β=0.63, p<0.01). Significant correlation was found between serum sHLA-G level and abdominal measurement (β=0.41, p<0.05) and estimated fetal weight (β=0.41, p<0.05). The amniotic sHLA-G level and placental perfusion (VI: β = -0.34, p<0.01 and VFI: β = -0.44, p<0.01, respectively) were negatively interrelated. A low amniotic sHLA-G level was significantly associated with nuchal translucency (r = -0.102, p<0.05). Conclusions: sHLA-G assayed in amniotic fluid might be a potential indicator for placental function, whereas the sHLA-G level in serum can be a prognostic modality for feto-placental insufficiency.

Nuclear waste is one of the most important environmental problems of nuclear power plants. A novel renewable distillation method has been proposed for an on-site recycling of the spent nuclear fuel and separation of its valuable components from the fissile isotopes, which is especially applicable for reactors using liquid fuels.

We delve into the intricate dynamics governing anisotropic fluids within the cosmological paradigm, elucidating the nuanced influence of conformal anomalies upon the stress-energy tensor. Through the presentation of a sophisticated theoretical framework, we seamlessly intertwine unconventional fluidic properties with profound cosmological considerations, thereby augmenting and refining our comprehension of the primordial universe.

A semi–numerical approach proposed many years ago for describing gravitational collapse in the post–quasi–static approximation , , , , is modified in order to avoid the numerical integration of the basic differential equations the approach is based upon. For doing that we have to impose some restrictions on the fluid distribution. More specifically, we shall assume the vanishing complexity factor condition, which allows for analytical integration of the pertinent differential equations and leads to physically interesting models. Instead, we show that neither the homologous nor the quasi–homologous evolution are acceptable since they lead to geodesic fluids, which are unsuitable for being described in the post–quasi–static approximation. Also, we prove that, within this approximation, adiabatic evolution also leads to geodesic fluids and therefore we shall consider exclusively dissipative systems. Besides the vanishing complexity factor condition, additional information is required for a full description of models. We shall propose different strategies for obtaining such an information, which are based on observables quantities (e.g. luminosity and redshift), and/or heuristic mathematical ansatz. To illustrate the method, we present two models. One model is inspired in the well known Schwarzschild interior solution, and another one is inspired in Tolman VI solution.

This paper investigates the search for an exact analytic solution to a temporal first-order differential equation that represents the number of customers in a non-stationary or time-varying

The objective of this study was to evaluate the pain and inflammatory response in soft tissues using healing and prosthetic abutments of different diameters and lengths. Methods: The study population was rehabilitated with Astra tech EV single implants (Dentsply Sirona, Atlantis, Dentsply Sirona S.A., Barcelona, Spain), 4.2 and 4.8 millimetres in diameter in upper and lower maxilla and loaded with custom abutments digitally designed with the software of the company Dentsply Sirona (Atlantis WebOrder, Dentsply Sirona S.A., Barcelona, Spain), version 4.6.5, with a larger diameter than the healing abutment, to account for biomarkers through ELISA. Results: Rehabilitations in mandible and with healing abutments below 4.29 millimetres and rehabilitators below 2.18 millimetres elicited higher pain and inflammatory responses, and in turn higher interleukin 1β values. Conclusions: Greater inflammation was evident in cases in which healing abutments with reduced diameter were used in relation to the same subsequent rehabilitation with prosthetic abutments of larger diameter.

Prolonged ethanol (EtOH) consumption is associated with male infertility with a decreased spermatogenesis rate as one cause. Defective maturation and development of sperm during their storage in the cauda epididymis and transit in the seminal vesicle can be another cause, possibly occurring before the drastic spermatogenesis disruption. Herein, we demonstrated that the cauda epididymis and seminal vesicle of rats, orally fed with EtOH under a regimen that spermatogenesis was still ongoing, showed histological damage, including lesion and decreased height of the epithelial cells, and increased collagen fibers in the muscle layer, which implicated fibrosis. Lipid peroxidation (shown by malondialdehyde (MDA) levels) was observed, indicating that reactive oxygen species (ROS) was produced along with acetaldehyde during EtOH metabolism by CYP2E1. MDA, acetaldehyde and other lipid peroxidation products could further damage cellular components of the cauda epididymis and seminal vesicle and this was supported by increased apoptosis (shown by TUNEL assay and caspase 9/caspase 3 expression) in these two tissues of EtOH-treated rats. Consequently, functionality of the cauda epididymis and seminal vesicle in EtOH-treated rats was impaired, as demonstrated by decreases in 1H NMR-analyzed metabolites (e.g., carnitine, fructose), which were important for sperm development, metabolism and survival in their lumen.

Recently, a high internal surface of the titanium alloy pipe is required due to the increment of various applications of the pipe such as aerospace. However, the traditional machining process is unable to effectively polish the internal surface of the slender pipe. Thus, a vertical magnetorheological polishing (VMRP) apparatus is carried out in this work to implement high polishing performance on the internal surface of the titanium alloy pipe. The polishing process is realized by the combination of the rotating motion of the pipe and the reciprocating linear motion of the polishing head. Moreover, a series of comparative experiments are conducted to investigate the polishing mechanism of magnetorheological (MR) fluid and enhance the polishing performance. It is shown from the experimental results that proposed VMRP approach exhibits the better polishing performance than the conventional horizontal MR polishing method under same testing conditions. This is because the proposed VMRP method well eliminates the traces of polishing particles owing to the combination of polishing particles with different sizes. In addition, it is identified from the experimental test that the polishing time of the VMRP required to achieve the same polishing effect as the conventional method is shortened under the combination of different rotation speeds. It is identified from the above benefits of the VMRP that the final surface roughness after polishing is below 0.05 μm.

The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.

: AliCPT-1 is the first Cosmic Microwave Background (CMB) experiment in China, dedicated to achieve accurate measurements of B-mode polarization. Situated in Ali of Tibet, China, this telescope is currently undergoing deployment and will operate in two frequency bands centered at 90 and 150 GHz. The Far-Field Flat Mirror（FFF）is a calibration device of AliCPT-1 telescope for far-field beam mapping. The design of FFF is optimized for easy assembly and adjustment. Meteorological station data reveals that the maximum wind speed near FFF is 17.5 m/s, while the maximum wind speed on the windward side is 8 m/s. The wind pressure on FFF was analysed using a maximum wind speed of 17.5m/s as the input condition, based on the fluid-structure coupling method in ANSYS. The results demonstrate that it is safe and reliable when withstanding combined gravity and wind pressure loads. The torque on the mount is within the motor rated torque. The flatness of the FFF reflective surface can be adjusted to an RMS value of 0.05 mm when taken into account the effect of gravity and assembly accuracy. The deformation caused by the maximum wind loads is approximately 0.0587 mm under the protection of wind-proof wall. The combined deformation is 0.077 mm in RMS value combining the two influences, which is less than 1/20 of wavelength. The FFF mirror assembly is stable and precisely for telescope calibration.

Hydrocephalus is caused by an overproduction of cerebrospinal fluid (CSF), a blockage of fluid circulation, or improper reabsorption. CSF accumulation in the brain’s ventricles causes ventriculomegaly and brain cell damage. Hydrocephalus can be caused by brain trauma, hemorrhage, infection, tumors, or genetic mutations. Currently, there is no cure for hydrocephalus. Treatments like shunting and endoscopic third ventriculostomies are used, but unfortunately, these techniques require brain surgery and have high failure rates. To advance the development of hydrocephalus treatments, physiologically relevant pre-clinical models are crucial. This review covers some of the current animal and cell culture methods used to study hydrocephalus. The choroid plexus epithelium (CPe) is thought to be the major producer of CSF in the brain. It is a polarized epithelium that regulates ion and water movement from a fenestrated capillary exudate to the ventricles. Despite decades of research, control of electrolyte movement in the CPe is still not fully understood. This review discusses important transporters on the CPe and how some of these could be potential targets for hydrocephalus treatment.

The recent green manufacturing demands have boosted the development of new biodegradable lubricants to replace petroleum-based lubricants. In this regard, water-based lubricants have been at the forefront of recent research for a wide range of industrial applications, including metalworking fluids (MWFs). In this work, we present an experimental investigation on the performance of novel green MWFs based on aqueous nopal mucilage solutions. For this, fully biodegradable solutions with different mucilage concentrations were evaluated in terms of rheological, tribological, thermal stability and turning (minimum quantity lubrication) performance, and compared to a commercial semisynthetic oil-based MWF (Cimstar 60). Mucilage solutions exhibited viscoelastic shear-thinning behavior, which was enhanced along with mucilage concentration. The solution with the highest mucilage content studied resulted in the lowest wear, friction and temperature in comparison to the other solutions and neat water in extreme pressure four-ball tests, and a similar level of lubricity as compared to the commercial MWF in cutting tests. This performance is associated to the enhanced viscosity and elasticity of the solution, as well as to the contents of lipids with fatty acids in the mucilage. Overall, the present results reveal the relevance of the viscoelastic behavior of the lubricant, elasticity in particular, in lubrication processes, and points to nopal mucilage as an effective green additive to produce innocuous MWFs.

Alzheimer’s disease (AD) is one of the most widespread neurodegenerative diseases affecting people averaging over 65 years. It manifests with severe cognitive damage, loss of memory, impairment in performing activities, ventricular expansion and final dementia. AD is associated with the deposit of amyloid β protein (Aβ) plaques, intracellular neurofibrillary tangles (NFTs), progressive inflammation and impairment of synaptic transmission and of mitochondrial function. Due to the poor diagnostic tools for the early stages of the disease, proteomics biomarkers have gained a paramount role because they can monitor the prodromal variations of the disease-linked molecular changes. Further, proteome biomarkers can help the follow up of AD progression over time and aid in setting personalized medical care, before the catastrophic consequences of dementia occurs. Research has focused on the identification of proteome biomarkers in cerebrospinal fluid (CSF) and plasma, which are discussed in the present review, but also in other matrices, as saliva and urine, revealing the high potentiality of proteomics approach and, at the same time, the difficulty to identify, for the different stages of the disease, sensitive and specific biomarkers clinically available.

Abdominal aortic aneurysm (AAA) is a chronic disease in which the abdominal aorta expands until it ruptures. AAA incidence: 10 million/year (India), deaths: 40%-90% (13th leading cause of death in the USA). Current treatment methods make diagnosis difficult due to the lack of noticeable symptoms and inaccurately planned operations. Rupture Scope is a mathematical model to dramatically reduce AAA deaths and improve treatment efficiency. Using a case-specific replica/simulation of real-time abdominal aortic blood flow for monitoring without frequent imaging scans and a novel derived mathematical linear regression model to predict rupture date and expansion rate with an overall accuracy of 95.64%.

This research paper presents a comprehensive study on the gasification of wheat straw pellets in a 10-kW fixed bed gasifier through a combination of Computational Fluid Dynamics (CFD) simulation and experimental validation. The developed 2D CFD model in ANSYS meshing simulates the gasification process in ANSYS Fluent software. The investigation evaluates key parameters such as equivalence ratio, higher heating value, and temperature distribution within the gasifier to enhance syngas production efficiency. The simulated results exhibit a noteworthy agreement with experimental data obtained from gasification. The impact of the equivalence ratio on gas production and lower heating value (LHV) is systematically explored, revealing that an equivalence ratio of 0.35 is optimal for syngas production. The resulting producer gas composition at this optimum condition includes CO (~27.67%), CH4 (~3.29%), CO2 (~11.09%), H2 (~11.09%), and N2 (~51%). The study further investigates the positive influence of reactor temperature on increasing syngas quantity while considering the uneven shape of the reactor and various thermal reactions affecting temperature, static pressure, velocity, and density. The findings contribute valuable insights to improve the efficiency of fixed-bed gasifiers, offering essential information on performance parameters for sustainable and optimized syngas production.

In this study, nano-diamond (ND) and MoS2 powder are used as additives in a carbonyl iron based magnetorheological fluid (MRF) to improve its tribological performance. MRFs are prepared by dispersing 35 wt.% of CI particles in silicone oil, and adding different proportions (0, 1, 3 or 5 wt.%) of ND and MoS2 additives. Seven kinds of MRFs are made and tested using reciprocating friction and wear tester under different normal loads, and then the friction characteristics are evaluated through analyzing experiment results. The morphology properties of MRFs and contacting surfaces before and after tests are also observed using a scanning electron microscope and analyzed by energy-dispersive X-ray spectroscopy. The results show that the appropriate weight percentage of MoS2 additives may decrease friction coefficient and wear zone. It is also demonstrated from the detailed analyses of worn surfaces that the wear mechanism is influenced not only by additives but also by applied normal load and magnetic field strength.

In view of the inability to directly and accurately obtain the athlete's aerodynamic force during take-off phase through wind tunnel test, the athlete's aerodynamic force and surrounding flow field form under different take-off postures are obtained through numerical simulation research, and the effects of different take-off modes on the aerodynamic characteristics during take-off in ski jumping are discussed. The multi-body system composed of the athlete and skis was selected as the research objects. By using partially averaged Navier-Stokes (PANS) turbulence model and 3D numerical simulation of computational fluid dynamics (CFD), the aerodynamic characteristics of the athlete under different take-off postures were predicted. Take-off modes include knee-push-hip (KPH) mode and hip-drive-knee (HDK) mode, and the hip joint angle of HDK mode is significantly greater than KPH mode. First, the aerodynamic force ratio of the athlete’s torso and legs is obviously large. Although the aerodynamic force of arms themselves is not obvious, they have a great impact on the overall aerodynamic characteristics of the athlete, so the posture of arms cannot be ignored. Then, the total drag and moment of HDK mode are significantly higher than that of KPH mode, and the lift-to-drag ratio of HDK mode is significantly lower than that of KPH mode. At first the total lift of HDK mode is higher than that of KPH mode, but in the last attitude the total lift of HDK mode does not rise but fall, and finally the total lift of HDK mode is lower than KPH mode. The aerodynamic characteristics change dramatically during take-off phase, and the aerodynamic characteristics of the two take-off modes are quite different, and these changes and differences are difficult to be observed in real training and competition site. KPH mode has obvious aerodynamic advantage over HDK mode. During the take-off process, the athlete should increasethe force generated by the knee joint extension and appropriately reduce the speed of hip joint extension, and control the using force order of the lower limb joints, and push hip joint extension by knee joint extension, in order to avoid issues such as the hip joint angle is too large, the hip joint extension angle is too fast, the center of gravity is to back and other problems. Studying the aerodynamic characteristics during the take-off phase provides valuable insights for athletes to achieve favorable flight postures after take-off, offering scientific guidance to improve training strategies and enhance competitive performance.

We consider that the relationship between entropy in statistical mechanics, which is the Boltzmann principle, and the complex velocity potential in complex fluid dynamics. We define the generalized complex entropy which expanded entropy from real space to complex space. We show that the complex entropy can be expressed by the composition of sources, sinks and laminar flows of the complex velocity potential. Therefore, the complex entropy is considered a special case of the complex fluid dynamics,that is, the complex velocity potential. In other words, we show that the complex entropy is expressed by the complex velocity potential. Moreover, we show that a complex number is expressed by the complex entropy. Thus, we show that the complex velocity potential is expressed by the complex entropy. Namely, we will expand entropy to complex space and see that the complex entropy is expressed by the complex velocity potential. Furthermore, we examine the possibility that it is an expansion of Boltzmann's principle and Planck distribution.

Respiratory distress syndrome (RDS) is a major respiratory morbidity associated with prematurity. In this case-control study, we prospectively evaluated whether targeted metabolomic analysis (gas chromatography–mass spectrometry) of the gastric fluid obtained from very preterm neonates (< 32 weeks’ gestation) during the first hour after birth could predict the need for exogenous surfactant for the treatment of RDS. 43 infants with RDS necessitating surfactant (cases) were compared with 30 infants with mild or no RDS (controls) who were not treated with surfactant. Perinatal and neonatal characteristics were recorded. Univariate analysis showed significant differences between the two groups in gastric fluid metabolites (L-glycine and acetyl-L-serine) and clinical parameters (gestational age, 1- and 5-minute Apgar scores, and intubation in the delivery room). Moreover, multivariate analysis revealed intubation in the delivery room as the most potent clinical predictor of surfactant administration [AUC of 0.69 (95% CI 0.57-0.81)]. The combination of metabolomic and clinical data allowed for the construction of a model with good accuracy [AUC 0.76 (95% CI 0.64-0.86)] in predicting surfactant replacement therapy. Further research is required to explore the role of gastric fluid metabolomics in the prediction of RDS and other neonatal outcomes.

Based on acoustic fluid elements, dynamic analysis was performed on liquid sloshing modes and liquid-filled containers considering the fluid-structure interaction (FSI) effect. The liquid sloshing modes in two-dimensional (2D) and three-dimensional (3D) containers were analyzed, and the results were compared with liquid sloshing modes measured in tests and theoretically calculated modes. This thus verifies correctness of the simulation method based on acoustic fluid elements. Cylindrical liquid-filled containers with different water levels were subjected to modal analysis and dynamic and time-historical analysis. Results show that the finite element analysis (FEA) based on acoustic fluid elements can accurately simulate liquid sloshing modes in liquid-filled containers and vibration characteristics of these containers with different liquid levels. The vibration frequency of liquid-filled containers declines obviously with rising liquid level. The liquid level significantly affects distributions of the maximum displacement, maximum acceleration, and maximum von Mises stress on the sidewall of liquid-filled containers. Numerical simulations based on acoustic fluid elements provides an effective and reliable method for dynamic analysis of liquid-filled containers considering the FSI effect.

Machine learning (ML) based on neural network (NN) facilitates data-driven techniques for handling large amounts of data, either obtained through experiments or simulations at multiple spatio-temporal scales, thereby finding the hidden patterns underlying these data and promoting efficient research methods. The main purpose of this paper is to extend the capabilities of a new solver, called realFluidReactingNNFoam, under development at University of Perugia in OpenFOAM with NN algorithm for replacing complex real-fluid thermophysical property evaluations, using the approach of coupling OpenFOAM and Python-trained NN models. Currently, NN models are trained against data generated using the Peng-Robinson equation of state (PR-EoS) assuming mixture frozen temperature. The OpenFOAM solver, where needed, calls the NN models in each grid-cell with appropriate inputs, and the returned results are used and stored in suitable OpenFOAM data structures. Such inference for the thermophysical properties is achieved via the “Neural Network Inference in C made Easy” (NNICE) library, which proved to be very efficient and robust. The overall model is validated considering a liquid-rocket benchmark comprised of liquid-oxygen (LOX) and gaseous-hydrogen (GH2) streams. The model accounts for real-fluid thermodynamics and transport properties, making use of the PR-EoS and the Chung transport models. First, the development of a real-fluid model (RFM) with artificial neural network is described in detail. Then, the numerical results of the transcritical mixing layer (LOX/GH2) benchmark are presented and analyzed in terms of accuracy and computational ef-ficiency. Results of the overall implementation indicate that the combined OpenFOAM and ML approach provides a speed-up factor higher than seven, while preserving the original solver accuracy.

Objective: The stability of the flight phase in ski jumping is crucial for athletes' performance and safety. This study aims to investigate the influence of unfavorable conditions on aerodynamic characteristics and flight stability through computational fluid dynamics (CFD) numerical simulations. Methods: The ski jumper and the skis are considered as a multi-body system. A detailed three-dimensional (3D) model of this multi-body system under a commonly observed posture during flight is established. The partially averaged Navier-Stokes (PANS) turbulence model is employed, and CFD simulations are conducted to predict the aerodynamic characteristics of the multi-body system under lateral environmental wind and asymmetric postures during flight phase. The conditions of asymmetric postures include yaw rotation and roll rotation. Results: (1) Lateral environmental wind generated yaw force, yaw moment, and roll moment, which influenced the lift, drag, and pitch moment of the athlete. These forces and moments were relatively small at lower wind speeds (less than 3 m/s) and became more significant at higher wind speeds (greater than 4.5 m/s). (2) Under the influence of yaw rotation or roll rotation, the multi-body system exhibited noticeable yaw force, yaw moment, and roll moment, all showing a monotonic increasing trend. Moreover, they had a significant impact on the lift, drag, and pitch moment of the multi-body system. Conclusion: (1) The influence of unfavorable conditions is complex, resulting in significant yaw force, yaw moment, and roll moment on the multi-body system. The adverse effects of roll rotation were generally greater than those of yaw rotation. (2) The multi-body system exhibited self-stabilizing tendencies in yaw and roll. This phenomenon can provide a solution to maintain flight stability by employing appropriate yaw or (and) roll rotation angles, effectively compensating for or even eliminating the adverse effects of lateral environmental wind. (3) Understanding the mechanisms of how unfavorable conditions affect the aerodynamic characteristics and stability during flight in ski jumping can provide valuable assistance for real-time prediction and decision-making during competitions, as well as scientific guidance for training athletes stable flight control and techniques and improving their sport performance.

Certain configurations of liquefied natural gas refueling stations exhibit a deficiency in managing boil-off gas. Furthermore, the ill-conceived linkage between the submersible pump and the gas storage tank pipeline leads to impeded natural gas transmission. This study employs Computational Fluid Dynamics (CFD) methodology to scrutinize the hydrodynamic attributes of T-type tee and dovetail tee configurations implemented in the pipeline design connecting the submersible pump and storage tank in an LNG filling station across diverse operational scenarios. The T-type tee induces detachment of the primary flow from the inner wall due to inertial forces, resulting in vortex formation and heightened resistance, accompanied by increased energy dissipation. Conversely, the dovetail tee, with its circular wall transition, mitigates vortex generation, reducing the separation zone and consequently minimizing resistance and energy loss. The maximum static differential pressure between the inlet and outlet of the dovetail tee is diminished by 52.52% when compared to that of the T-type tee. In the most noteworthy scenarios, the local resistance coefficient of the dovetail tee is even less than 1/10 of that of the T-type tee. In practical engineering applications, the incorporation of dovetail tees leads to a 17.58% reduction in the required elevation difference. This results in a more uniform flow field and enhanced stability in both flow rate and pressure. Such improvements contribute to heightened engineering efficiency and environmental sustainability, particularly evident in the design of LNG filling stations.

Covid-19 is an airborne disease, with the vast majority of infections occurring indoors. By comparison, little transmission occurs outdoors. Here, we investigate the airborne transmission pathways that differentiate the indoors from outdoors, and conclude that profound differences exist, which help to explain why SARS-CoV-2 transmission is much more prevalent indoors. Near and far-field transmission pathways are discussed along with factors that affect infection risk, with aerosol concentration, air entrainment, thermal plumes, and occupancy duration all identified as being influential. In particular, we present the fundamental equations that underpin the Wells-Riley model, and show the mathematical relationship between inhaled virus particles and quanta of infection. A simple model is also presented for assessing infection risk in spaces with incomplete air mixing. Transmission risk is assessed in terms of aerosol concentration using simple 1D equations, followed by a description of thermal plume-ceiling interactions. With respect to this, we present new experimental results using Schlieren-visualisation and Computational Fluid Dynamics (CFD) based on the Eulerian-Lagrangian approach. Pathways of airborne infection are discussed, with the key differences identified between indoors and outdoors. In particular, the contribution of thermal and exhalation plumes is evaluated, and the presence of near-field/far-field feedback loop postulated, which is absent outdoors.

Orogenic antimony-gold deposits contribute significantly to the global antimony resource base. China's orogenic antimony-gold deposits are primarily in southern Tibet. Investigations indicate that antimony combines and migrates with sulfur hydroxides in ore-forming fluids. Previous research on fluid inclusions in orogenic antimony-gold ores with sedimentary rock accommodation revealed the presence of organic inclusions, including liquid hydrocarbons, alongside common components such as CO2, H2O, CH4, and NaCl. However, the impact of liquid hydrocarbons on antimony migration and mineralization is still de-batable. To investigate the transportability of antimony by liquid hydrocarbons in orogenic antimony ores, we selected n-dodecanethiol and n-dodecane as the subjects. We measured the solubility and occurrence form of antimony in these compounds at various temperatures and durations. The results indicate that after 5 and 10 days of reaction at 100 °C, the antimony concentrations in the n-dodecanethiol and n-dodecane groups were 67.44±7.62 ppm, 75.15±16.74 ppm, 1.40±1.02 ppm, and 3.02±3.09 ppm, respectively. At 150 °C for 5 and 10 days, the respective concentrations were 50.58±5.39 ppm, 77.26±45.20 ppm, 2.66±3.08 ppm, and 2.41±2.03 ppm. At 200 °C for 5 and 10 days, the corresponding concentrations were 339.76±71.94 ppm, 218.97±25.03 ppm and 6.53±7.17 ppm, 2.27±0.82 ppm (n=3). The measured solubility of antimony in the n-dodecanethiol group increased gradually with rising temperature. The solubility of antimony in the n-dodecane group was low and notably inferior to that observed in the n-dodecanethiol group. X-ray photoelectron spectroscopy (XPS) analysis demonstrated a distinct thiol (R-SH) peak at 163.31 eV and compound peaks of antimony reacting with thiols at 162.06 and 160.87 eV. This suggests that antimony predominantly forms complexes with thiols for migration. Our findings suggest that specific liquid hy-drocarbon components, predominantly thiols, can interact with antimony at metallogenic temperatures and persist in ore-forming fluids, facilitating migration and mineral enrichment. Earlier experimental studies on gold and crude oil have indicated that liquid hydrocarbons also play an essential role in the transportation and enrichment of gold during the formation of gold deposits, thus indicating that liquid hydrocarbons possess the considerable potential to act as an ore-forming fluid during orogenic antimony-gold deposit formation in southern Tibet.

In Active Flow Control (AFC) applications, to activate the boundary layer the use of pulsating flow has notorious energy advantages versus constant blowing/suction jet injections. For a given AFC application, five parameters, jet location and width, inclination angle, frequency of injection and momentum coefficient need to be tuned. Two main devices are nowadays capable of injecting pulsating flow with the sufficient momentum coefficient to delay the boundary layer separation, these are the Zero Net Mass Flow actuators (ZNMFA) and the Fluidic Oscillators (FO). In the present research, a novel FO configuration is analyzed for the first time at relatively high Reynolds numbers, fluid is considered as incompressible. After obtaining the typical linear correlation between the incoming Reynolds number and the outlet flow oscillating frequency, the effect of outlet width and mixing chamber wedge inclination angle dimensional modifications is addressed, modifications of the outlet width are observed to create large variations on the FO performance. The origin of the self-sustained oscillations is also analyzed in the present manuscript and greatly helps in clarifying the forces acting on the jet inside the mixing chamber. In fact we can conclude saying that the current FO configuration is pressure driven although the mass flow forces appear to be a much more relevant than in previous FO configurations studied.

Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

Efficient implementation of clean energy technologies, including pioneering solutions like mobile solar PV systems mounted on trailers (MSPT), is pivotal for addressing energy challenges, especially in regions with constrained power grid access. This endeavour is vital for meeting escalating elec-tricity demands and aligning with the UN Sustainable Development Goal (SDG) aimed at ensuring dependable and sustainable energy provision in developing countries. This paper investigates the aerodynamic behaviour of a designed MSPT using numerical and experimental approaches. Spe-cifically, the study focuses on the effects of wind velocity and tilt angels on the drag and lift forces, as well as drag and lift coefficients on the panel used in the MSPT system. Additionally, the overall wind force acting on the entire MSPT (including 9 large solar PV panels) was examined, considering the combined effects of wind flow and the system's geometry. The simulations were conducted using ANSYS-Fluent software and experimental testing was performed utilizing scaled-down models to validate the accuracy of the simulation. The insights and the knowledge from this study can be utilized to optimize the design, installation, and operation of such systems, ultimately enhancing their performance, reliability, and paving ways for further improvements in mobile solar PV technology.

Computational rhinology is a specialized branch of biomechanics leveraging engineering techniques for mathematical modelling and simulation to complement the medical field of rhinology. Computational rhinology has already contributed significantly to advancing our understanding of the nasal function, including airflow patterns, mucosal cooling, particle deposition, and drug delivery, and is foreseen as a crucial element in e.g. the development of virtual surgery as a clinical, patient-specific decision support tool. The current paper delves into the field of computational rhinology from a nasal airflow perspective, highlighting the use of computational fluid dynamics to enhance diagnostics and treatment of breathing disorders. The paper consists of three distinct parts – an introduction to and review of the field of computational rhinology, a review of published literature on in vitro and in silico studies of nasal airflow, and the presentation and analysis of previously unpublished high fidelity CFD simulation data of in silico rhinomanometry. While the two first parts of the paper summarize the current status and challenges in the application of computational tools in rhinology, the last part addresses the gross disagreement commonly observed when comparing in silico and in vivo rhinomanometry results. It is concluded that this discrepancy cannot readily be explained by CFD model deficiencies caused by poor choice of turbulence model, insufficient spatial or temporal resolution, or neglecting transient effects. Hence, alternative explanations such as nasal cavity compliance or drag effects due to nasal hair should be investigated.

Reservoir computing (RC) systems can efficiently forecast chaotic time series using nonlinear dynamical properties of an artificial neural network of random connections. The versatility of RC systems has motivated further research on both hardware counterparts of traditional RC algorithms and more efficient RC-like schemes. Inspired by the nonlinear processes in a living biological brain and using solitary waves excited on the surface of a flowing liquid film, in this paper we experimentally validate a physical RC system that substitutes the effect of randomness for a nonlinear transformation of input data. Carrying out all operations using a microcontroller with a minimal computational power, we demonstrate that the so-designed RC system serves as a technically simple hardware counterpart to the `next-generation’ improvement of the traditional RC algorithm.

The intensive variables, geochemical, mineralogical and petrogenetic constraints of the Iberian rare metal granites, many of them unknown, are presented. It allows to distinguish two main granitic types with contrasting characteristics: Nb-Ta-rich granites and Nb-Ta-poor granites. The former have lower emplacement temperatures, higher water contents and probably lower emplacement pressures than Nb-Ta-poor granites. Nb-Ta-rich granites also have higher fluoride contents, strong fractionation into twin pairs such as Zr-Hf, Y-Ho and Nb-Ta, and an abundant, probably exsolved, fluid phase, which is not or not as evident in Nb-Ta-poor granites, probably in part because the Nb-Ta-rich granites reach their solidus later (about 550 ºC). The geochemical signature of the Iberian rare metal granites follows the trends of mainly two-mica granites and P-rich cordierite granites, but also of granodiorites and even type I granites, suggesting that the rare metal granites may have different parental magmas. Thermodynamic modeling shows that many of the geochemical characteristics of the RMGs can be explained by a process of extreme differentiation, while others cannot, e.g. Na evolution. In terms of ore deposition, white mica plays a very important role in explaining the variation of the Ta/Nb ratio, although the latter could also be controlled by late Nb-Ta oxides crystallization and even by acidic fluids that remove Nb relative to Ta from earlier Nb-Ta oxides.

This paper provides the numerical investigation of two-dimensional stochastic Navier-Stokes equation driven by additive white noises. The vorticity-stream function method is presented to calculate the incompressible fluid flow. In order to solve the formulation of steam function equation, we propose a Crank-Nicolson Fourier pseudo-spectral method. Numerical results obviously show that the presence of stochastic forcing can have an impact upon the shapes of vortex in fluid flow. To a certain extent, the phenomenon of eddy shedding and the formation of some new vortex in a random medium can be observed, which make it possible for us to conduct optimal control experiments in the development of vortex structures.

Innovations in drug delivery systems are crucial for enhancing therapeutic efficiency. Our research presents a novel approach based on Electro-fluid dynamic atomization (EFDA) to fabricate core-shell monophasic particles (CSMp) from sodium alginate blends of varying molecular weights. This study explores the morphological characteristics of these particles in relation to material properties and process conditions, highlighting their potential in drug delivery applications. A key aspect of our work is the development of a mathematical model that simulates the release kinetics of small molecules, specifically sodium diclofenac. By assessing the diffusion properties of different molecules and gel formulations through transport and rheological models, we have created a predictive tool for evaluating the efficiency of these particles in drug delivery. Our findings underscore two critical independent parameters for optimizing drug release: the external shell thickness and the diffusivity ratios within the dual layers. This allows for precise control over the timing and intensity of the release profile. The study advances our understanding of EFDA in the fabrication of CSMp and offers promising avenues for enhancing drug delivery systems by tailoring release profiles through particle characteristic manipulation.

Acute pancreatitis (AP) is a leading gastrointestinal disease that cause hospitalization. Initial management in the first 72 h after the diagnosis of AP is pivotal, which can influence the clinical outcomes of the disease. Initial management, including fluid resuscitation, pain control, nutritional support, antibiotic use, and endoscopic retrograde cholangiopancreatography (ERCP) in gallstone pancreatitis, plays a fundamental role in AP treatment. Recent updates for fluid resuscitation, including treatment goals, the type, rate, volume, and duration, have triggered a paradigm shift from aggressive hydration with normal saline to goal-directed and non-aggressive hydration with lactated Ringer’s solution. Evidence of the clinical benefit of early enteral feeding is becoming definitive. Routine use of prophylactic antibiotics is generally limited, and the procalcitonin based algorithm of antibiotic use has recently been investigated to distinguish between inflammation and infection in patients with AP. Although urgent ERCP (within 24 h) should be performed for patients with gallstone pancreatitis and cholangitis, urgent ERCP is not indicated in patients without cholangitis. Furthermore, convalescent treatment, including cholecystectomy in gallstone pancreatitis and alcohol intervention in alcoholic pancreatitis, is also important for improving the prognosis and prevent recurrence in patients with AP. This review focuses on recent updates on the initial and convalescent management strategies for AP.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

Subacute sclerosing panencephalitis (SSPE) is a progressive neurological complication that affects the central nervous system. It occurs as a late complication of the measles infection the young children and adolescents who are commonly affected present with personality changes and neurological deficits. The diagnosis can be done via clinical features, electroencephalography, and cerebrospinal fluid analysis. At present, there is no cure for SSPE. The immunisation against measles is the main strategy in preventing this condition. Here, we present a case of a 22-year-old Indian male diagnosed with Subacute sclerosing panencephalitis.

We will apply Pascal’s hydrostatic pressure law to black holes and also to the Hubble sphere. Haug has recently demonstrated how hydrostatic pressure in water can be utilized to determine the Planck length. One can conceptualize the energy in the Hubble sphere as a type of superfluid, and if this is correct, then Blaise Pascal’s hydrostatic pressure formula may also be applicable to such a superfluid, even within the Hubble sphere. By employing the same method on the Hubble sphere and considering it as a Schwarzschild black hole with the critical Friedmann mass, we can estimate the Planck length based on its hypothetical hydrostatic pressure.

In the previous work, the pure fatigue behavior of AM60 magnesium alloy (PF-AM60) was compared with the corrosion fatigue behavior of these specimens (CF-AM60). In this research, in continuation of the previous job, the pure fatigue behaviors of AM60 with polylactic acid (PLA) coating (PF-AM60-PLA) and also, corrosion fatigue behaviors of magnesium alloy with PLA coating (CF-AM60-PLA) were evaluated. Polymer coating was made by fused deposition modeling (FDM) with a 3D printer and attached to standard fatigue test specimens with a glue. Then, they were immersed in the simulated body fluid (SBF) for 27 days. In the end, a high-cycle bending fatigue test was performed on samples. The fracture surface of the samples was also observed using the field emission scanning electron microscopy (FESEM). Due to corrosion, the weight of the specimens redcued by an average of 35%. The corrosion rate decreased in the first 7 days and then increased. PF samples with coating had an average of 49% increase in fatigue lifetime. Regarding the CF samples, despite the use of a 10 times stronger solution, the fatigue lifetime of these samples decreased by only 35%. FESEM results also showed cleavage plates and striations. In addition, the separation of the glue from the coating and Mg was observed. Corrosion products including microcracks and holes were seen on the fracture surface of CF specimens, which caused stress concentration and crack growth. Holes caused by the release of gases were also observed in polymer coatings.

The automotive industry has witnessed a significant push towards increased fuel efficiency and reduced carbon emissions. Among many factors influencing overall vehicle efficiency, aerodynamic drag is a critical consideration, accounting for a substantial portion of fuel consumption. Our investigation focused on the drag coefficients of three prominent 2023 passenger car models – the Toyota Corolla, Hyundai Elantra, and Kia Soul. Using ANSYS Fluent to perform computational fluid dynamics, we demonstrated an inverse correlation between drag force and gas mileage, underlining the significance of aerodynamic design in fuel efficiency. Notably, the Hyundai Elantra emerged as the most aerodynamically efficient of the three vehicles, followed closely by the Toyota Corolla. In contrast, the boxier-designed Kia Soul exhibited significantly higher drag coefficients and drag forces, rendering it the least efficient of the trio. These findings emphasize the importance of environmental factors in car design. Shaping aerodynamic profiles directly impacts fuel efficiency, stability, and overall performance.

This study proposes a customized industrial nozzle for generating impulsive air jets. It is installed on an automatic machine where wine caps are stacked and shot consecutively into a rotating cylinder by an air jet. This process is very noisy; hence, this study aimed to investigate possible geometric variations of the nozzle that can reduce the emitted noise. First, the nozzle was tested in a laboratory to measure the air consumption at different supply pressures. Subsequently, 3D models of the nozzle and its variations were created and used for computational fluid dynamics simulations. Different boundary conditions were set, first to validate the model and compare it with the experimental test results, and then to simulate the real working conditions and determine the geometry that is less noisy while maintaining the velocity peak. Among the various possibilities, shortening the final ducts of the nozzle appears to be the most promising solution. These modified nozzles could be easily added to current machines to provide immediate benefits, and this study represents a promising start for action on other machines where this type of device is present.

Oil and Gas companies, both national and international, along with government regulators, share a common goal of efficiently managing their valuable assets. These assets refer to the Reserves of oil and Gas located underground. Typically, production and Reserves Engineers play a crucial role in managing these reserves through the implementation of well testing techniques. Thus far, the gold standard in this field has been to ensure the optimal management and utilization of these resources. In the context of well testing, the separator has traditionally been considered the gold standard. However, despite regulatory mandates for frequency of well testing (Such as the general requirements of every 30days in the Nigeria south East zone sector), There is a lack of specific regulations regarding the expected flow measurement uncertainties. This gap in the regulations leaves room for improvement in establishing guidelines for accurate flow measurements. This paper aim to Review the various test separator employed, examine the implications of the 30days testing interval under real - world conditions, and critically assess the achievable measurements uncertainties in the field. Additionally, it will provide a candid analysis that sheds light on the expected uncertainties associated with flow measurements. The introduction of the multiphase meters in the past two decades hold the potential for significant advancements in Reservoirs management performance. However, the authors suspect that this potential has not been universally realized. This paper aim to address this issue by examining the extent to which the benefits of multiphase meters have been effectively utilized in reservoir management. By doing so, it seeks to shed light on any existing gaps and propose recommendation for maximizing the impact of multiphase metres in the field. In addition to the aforementioned objectives, this paper will also address and explore the following key aspects:Identification and review of both the strength and weaknesses associated with test separators. By thoroughly examining these attributes, we can gain valuable insight into their effectiveness and potential areas for improvement. Exploration of alternative application of test separator and their impact on well testing efficiency. Real -World comparison will be provided to highlight the advantages and challenges associated with these alternative uses, offering a comprehensive understanding of their implications. Evaluation of the contribution that multiphase flows meters (MPFMs) can bring to the testing scenario and overall performance. By assessing the capabilities and potential benefits of MPFMs, we aim to provide a comprehensive picture of their role in enhancing testing procedures. Examination of the flow measurement uncertainties that can be expected from a test separator and their potential impact on reservoirs management performance. By understanding and quantifying these uncertainties, we can gain insight into how they may affect decision -making and optimization strategies in managing our materials assets effectively. Delving into the question of reconciling multiphase flow meter (MPFMs) with test separators. This analysis aims to inject a sense of realism into the world of managing our major material assets by explaining the challenges and opportunities associated with integrating and aligning these two measurement technologies. By addressing these crucial aspects, this paper strives to provide a comprehensive understanding of the complexities involved in managing our material assets, ultimately driving towards more informed decision-making and improved performance.

The influence of aluminosilicate pozzolanic waste, specifically spent fluid catalytic cracking catalyst (FCCW) and metakaolin waste (MK) from expanded glass industry, on the properties of hardened Portland cement paste were analysed. The study involved replacing part of cement with FCCW and MK and observing their impact on hydration, microstructure, density and compressive strength of hardened cement paste. Various analysis methods were employed, including X-ray diffraction (XRD), thermogravimetric analysis (TG), and scanning electron microscopy (SEM), to understand the changes in the structure of hardened cement paste during hydration. The findings revealed that FCCW tends to accelerate cement hydration process due to its high surface area and pozzolanic activity. Notably, the formation of portlandite crystals was observed on FCCW particle surfaces in a specific direction. These crystals appeared smaller and developed in different directions in compositions containing a composite binder with mixture of FCCW and MK in a ratio 1:1. This could be influenced by pozzolanic reactions activated by fine particles of MK and the formation of calcium silicate hydrates (CSH) and calcium alumino silicate hydrates (CASH) in the presence of portlandite. XRD and TG results indicated that the specimens containing a composite binder exhibited the least amount of portlandite. The compressive strength of these specimens increased compared to control specimens, although the amount of cement was 9% lower.

The present study investigates the role of a simple inerter in supplemental devices for possible implementation in the matured seismic base isolation technique. Firstly, the response of the base-isolated structure with an optimally tuned mass damper-inerter (TMDI) is investigated to see the tuning effects. The time required to tune the TMDI was found to be significantly longer than the duration of a strong-motion earthquake. There was still a reduction in the response of the isolated structure, which is primarily due to the added damping and stiffness (ADAS) of TMDI and not because of the tuning effects. Hence, it is proposed that the corresponding ADAS of the TMDI be directly added to the isolation device. Secondly, the response of the base-isolated structures with the fluid inerter damper (FID) is studied. It was observed that the inerter of the FID does not influence the displacement variance of an isolated structure under broadband earthquake excitation. It implies that the response of the isolated structure with FID is primarily controlled by its counterpart fluid damper (FD). The performance of optimal TMDI, ADAS, FID, and FD to mitigate the seismic response of the flexible multi-story base-isolated structure under real earthquake excitations is also investigated. In terms of suppressing the displacement and acceleration responses of the isolated structure, it has been found that TMDI and ADAS perform similarly. Comparing the response of the isolated structure with FID and FD demonstrated that the inerter in the FID has detrimental effects on the isolated structures, in which the top floor's acceleration and base shear are substantially increased.

The two-stage direct thermal contact (2sDTC) process is a rapid dewatering approach for fluid fine tailings (FFT) that is integrated into an oil sands bitumen extraction plant to reduce tailings pond storage and freshwater usage. In the first stage, combustion gas directly contacts atomized FFT, vaporizing water and yielding dry solids and steam-rich hot gas. The second stage involves pond effluent water directly contacting the steam-rich hot gas, recovering heat and condensing moisture. Case studies confirm the technical feasibility of the integration. Benefits include producing a dry discharge, reducing tailings water discharge and conserving an equivalent to 0.2 barrels of freshwater per barrel of oil produced. Most importantly, these benefits incur no additional energy cost to the plant as the integration eliminates the energy penalty and CO2 emissions associated with FFT dewatering. Further capacity enhancement can be achieved by using centrifuge-concentrated FFT. The study reveals that FFT concentrated to ~50 wt% solids could still maintain its pump-ability and be accommodated by the 2sDTC process, leading to an integration which could dewater more FFT annually and conserve more freshwater ( 0.58 barrels per barrel of oil produced), with the sole energy requirement being the power to drive the centrifuge machinery.

This research provides a computationally efficient numerical tool for predicting 3-D turbulent flows over hydrofoils. It addresses a gap in existing numerical methods by extending the capabilities of the laminar VIScous Vorticity Equation (VISVE) solver to handle 3-D turbulent flow scenarios. The implementation integrates the k − ω SST model into the 3-D VISVE solver using the Finite Volume Method (FVM), extending its capability to handle turbulent flows. The turbulence model is also parallelized to improve computational efficiency. The application of the newly developed model to 3-D hydrofoil cases expands its scope and serves as preparatory work for future rotational propeller applications. Rigorous testing includes a convergence analysis concerning grid numbers and time step sizes, and validation against a Reynolds-Averaged Navier-Stokes (RANS) solver ensures the reliability and accuracy of the enhanced VISVE solver for turbulent flow simulations. The turbulent VISVE solver offers advantages such as reduced computational domain and costs through a vorticity-based approach. Turbulence concentration within boundary layers and free shear flows does not compromise the advantages of the small computational domain. The simplified meshing process, automatically generated by denoting the number of panels on the hydrofoil, makes the solver accessible for researchers and engineers.

Metachrony is defined as coordinated asynchronous movement throughout multiple appendages, such as the cilia of cells and swimmerets of crustaceans. We investigate the process of metachronal propulsion, notably used by species of crustaceans and microscopic cells to move through fluid. A rigid crustacean model with paddles moving in symmetric strokes was created to simulate metachronal movement. Coupled with the surrounding fluid domain, we employ the immersed boundary method to analyze fluid-structure interactions. To explore the effect of nonlinear morphology on the efficiency of metachronal propulsion, we generate and simulate a range of crustacean body shapes, from upward curves to downwards curves. We found that the highest propulsion velocity is achieved when the crustacean model morphology follows a downwards curve, specifically a parabola of leading coefficient k=−0.4. This curved morphology results in 4.5% higher velocity compared to the linear model. As k deviates from −0.4, the propulsion velocity decreases with increasing magnitude, forming a concave downward trend. The impact of body shape on propulsion velocity is shown by how the optimal velocity with k=−0.4 is 71.5% larger than the velocity at k=1. Overall, this study suggests that morphology has a significant impact on metachronal propulsion.

We consider boundary value problems for a nonlinear mass transfer model, which generalizes the classical Boussinesq approximation, under inhomogeneous Dirichlet boundary conditions for the velocity and the substance’s concentration. It is assumed that the leading coefficients of viscosity and diffusion and the buoyancy force in the model equations depend on concentration. We develop mathematical apparatus of studying inhomogeneous boundary value problems under consideration. It is based on using of a weak solution of the boundary value problem and construction of liftings of the inhomogeneous boundary data. They remove the inhomogeneity of the data and reduce original problems to equivalent homogeneous boundary value problems. Based on this apparatus we will prove the theorem of the global existence of a weak solution to boundary value problem under study and establish important properties of the solution. In particular, we will prove the validity of the maximum principle for the substance’s concentration. We will also establish sufficient conditions for the problem data, ensuring the local uniqueness of weak solutions.

Infertility affects millions worldwide, posing a significant global health challenge. The proteomic analysis of follicular fluid provides a comprehensive view of the complex molecular landscape within ovarian follicles, offering valuable information on the factors influencing oocyte development and on the overall reproductive health. The follicular fluid is derived from the plasma and contains various proteins that can have different roles in oocyte health and infertility and this fluid is a critical microenvironment for the developing oocytes as well. Using HPLC/MS method we investigated the protein composition of the follicular fluid and after classification we did relative quantification of the identified proteins in the pregnant (P) and non-pregnant (NP) groups. Based on the protein-protein interaction analysis ALB and ApoA1 was found to be hub proteins and the quantitative comparison of the P and NP groups resulted significantly lower concentration of ApoA1 and HDL-cholesterol in the P group. As both molecules are involved in the cholesterol transport, we also investigated their role in the development of oocytes and in the prediction of fertility.

Sepsis is defined as life-threatening organ dysfunction caused by a dysregulated host response to an infection. Recent in-vitro studies have investigated the effects of CytoSorb hemoadsorption on endothelial function in sepsis showing a reduction in markers of endothelial dysfunction, but to this day there is a lack of clinical studies showing whether this approach could actually positively influence the disturbed vascular barrier function in septic conditions. We analyzed the data on administered fluid volumes and catecholamines to determine the potential benefit of CytoSorb hemoadsorption therapy on endothelial function in a clinical scenario. We performed a retrospective analysis of 124 septic shock patients who had undergone adjunctive treatment with CytoSorb hemadsorption therapy. We collected volume requirements, and calculated the volume balance within different time periods to obtain an assumption on the stability of the vascular barrier. We also calculated catecholamine requirements. With regard to the entire study cohort our findings revealed a significant reduction in fluid balance at 72 hours (T72) compared to both baseline (T0) and the 24-hour mark (T24). Fluid balances from T72 – T0 were significantly lower in hospital survivors compared to non-survivors. Patients who received a second catecholamine had a significantly lower in-hospital mortality. Our findings showed that use of hemoadsorption therapy results in a reduced positive fluid balance paralleled by reductions in vasopressor needs suggesting a positive effect on endothelial integrity. These results, derived from a large cohort of patients, provide valuable insights that may greatly improve our understanding of the multiple effects of hemoadsorption treatment in septic shock patients.

Background and Objectives: Obesity-related elevated body mass index (BMI) across life is associated with chronic low-grade inflammation and increased levels of C-reactive protein (CRP) in blood. CRP is a marker and promoter of inflammation. The objectives of this study were to examine the effect of obesity on the relationship between peripheral and gingival CRP levels and examine the effects of gingival CRP levels on gingival fluid inflammatory cytokines in periodontitis resistant obese individuals. Materials and Methods: Thirty-nine, periodontally healthy subjects were enrolled. Based on BMI scores, 20 subjects were categorized as lean and 19 as obese. A comprehensive periodontal examination was performed. Gingival crevicular fluid (GCF) and blood samples were collected. Both GCF and blood samples were assessed for interleukin-1β (IL-1β), interleukin-6 (IL-6), interleukin-8 (IL-8), tumor necrosis factor-α (TNF-α), interleukin-10 (IL-10), interleukin-17A (IL-17A) and CRP. Results: GCF CRP levels were significantly higher in obese than lean individuals. No statistically significant differences were noted between the two groups in both GCF and blood on any of the inflammatory cytokine levels. IL-17A was not detected in GCF of most subjects in both groups. GCF CRP levels were positively associated with blood CRP levels, the association tended to be stronger in obese individuals. GCF CRP showed no associations with GCF IL-10 in both groups. Although GCF CRP levels positively associated with multiple GCF inflammatory cytokines (e.g., IL-1β, IL-6, IL-8 and TNF-α) in all subjects, the associations tended to be weaker in obese individuals (e.g., IL-1β, IL-6, TNF-α). Furthermore, the levels of GCF inflammatory cytokines IL-6 and TNF-α were depressed in obese individuals. Conclusions: Obesity unfavorably influences the relationship between blood and GCF CRP levels and promotes increased CRP levels in GCF. Collectively, the findings suggest a dysregulated inflammatory cytokine response in the gingival tissues of obese individuals.

Recently, more wind turbine systems are being installed in deep waters far from the coast. Several concepts of floating wind turbine systems (FWTSs) are developed, among which the semisubmersible platform, due to its applicability in different water depths, good hydrodynamic performance, and facility in the installation process, constitutes the most explored technology compared to the others. However, a significant obstacle to the industrialization of this technology is a design of a cost-effective FWTS, which can be achieved by optimizing the geometry, size and weight of the floating platform, along with the mooring system. This is only possible by selecting a method capable of accurately analyzing the FWTS coupled hydro-aero-structural dynamics at each design stage. Accordingly, this paper aims at providing a detailed overview of the most common coupled numerical and physical methods, including their basic assumptions, formulations, limitations, and costs, used for analyzing the dynamics of FWTSs, mainly those supported by a semisubmersible, to assist the choice of the most suitable method at each design phase of FWTSs. Finally, the article discusses possible future research to address challenges in modeling FWTSs dynamics that persist to date.

Small submersible drainage pumps discharge leaking water and rainwater in buildings. In an emergency (e.g., heavy rain or accident), monitoring the flow rate in advance is necessary to enable optimal operation, considering the point where the pump operates abnormally when the water level increases rapidly. In another, pump performance optimization is crucial for energy saving policy. Therefore, it is necessary to meet the challenges of submersible pump systems, including sustainability and pump efficiency. The final goal of this study is to develop an energy-saving, high-efficiency submersible drainage pump capable of responding to emergencies. In particular, this paper targeted the hydraulic performance improvement of a submersible drainage pump model. Before the development of driving mode-related technology capable of emergency response, we first tried to find a way to improve the performance characteristics of the existing submersible drainage pump. Rather than designing a new pump, we disassembled the current pump and reverse engineering. Then, numerical simulation was performed to analyze the flow characteristics and efficiency of the pump. Then, the pump test was carried out to obtain the performance and validated with numerical results. Results revealed that changing the cross-sectional shape of the impeller reduced the flow separation and enhanced velocity and pressure distributions. Also, it reduced the power and increased efficiency. Results also showed that the pump's efficiency increased to 5.56% at a discharge rate of 0.17 m3/min, and overall average efficiency increased to 6.53%. In addition, the submersible pump design method could be suitable for the optimized pump's impeller and casing numerically. This paper can provide insight and information on the design optimization of pumps.

In the research we consider a structure-fluid interaction of oscillating piezodevice and acoustic liquid. Such problem requires finding resonance or anti-resonance frequencies of the solid structure to use them in the latter frequency-response analyses step. After finite element discretization of the issue, we need to solve a generalized eigenvalue problem (GEP). The most efficient numerical method for solving the partial GEP is the shift-and-invert Lanczos method. Each step of this algorithm requires solving a large scale system of linear algebraic equations (SLAEs) with special properties. Various ways of ordering grid nodes lead to coefficient matrices with different structure. Several methods are compared in terms of efficiency. The results of the numerical experiments are presented.

The basis of modern teeth whitening systems is the use of a whitening gel, usually containing hydrogen peroxide or carbamide peroxide. The purpose of our study was to evaluate the effect of chemical and modified office teeth whitening systems on the mineral metabolism of oral fluid and to determine a safer method. The study covered 81 patients aged 22 to 35 years of both sexes with teeth color A2 and darker on the Vita Classic scale. Determination of the concentration of calcium and phosphates in the oral fluid was carried out on a spectrophotometer using ready-made Human kits. Chemical tooth whitening was performed using a gel based on 40% hydrogen peroxide. After the procedure, remineralization therapy with enamel-sealing liquid was performed for 14 days. The obtained results indicate that the most pronounced changes in the content of calcium (+74.4%, p &lt;0.001) and рhosphates (phosphorus) (-23.07%, p &lt;0.001) were observed when using a chemical bleaching system. After the teeth whitening procedure using a modified technique, less pronounced changes in the concentrations of calcium (+29.07, p &lt;0.001) and phosphorus (-14%, p &lt;0.001) were observed. The use of remineralizing agents led to a faster recovery of the initial levels of calcium and phosphates in the oral fluid. Both bleaching systems caused similar changes in the chemical composition of the oral fluid.

This review paper presents a flashback on the evolution of the disease throughout the centuries, describes in summary pathophysiologic mechanisms, discusses briefly the mechanism of action of the diuretics, presents their role in decongesting heart failure patients and unfolds the data behind ultrafiltration in the management of acutely or chronically decompensated heart failure (ADHF), focusing on all the available data and advancements in this field. Acutely decompensated heart failure (ADHF) presents a critical clinical condition characterized by worsening symptoms and signs of heart failure, necessitating prompt intervention to alleviate congestion and improve cardiac function. Diuretics have traditionally been the mainstay for managing fluid overload in ADHF. Mounting evidence suggests that due to numerous causes, such as coexisting renal failure or chronic use of the loop diuretics, an increasing rate of diuretic resistance is noticed and needs to be addressed. There has been a series of trials that combined diuretics of different categories, without the expected results. Emerging evidence suggests that ultrafiltration may offer an alternative or adjunctive approach.

The paper proves the existence of a family of axisymmetric equilibrium figures as solutions of a stationary problem with unknown boundaries for the Navier–Stokes equations corresponding to the slow rotation of a viscous compressible two-layer liquid mass about some axis. It is assumed that the liquids are barotropic, capillary and have different viscosities, the internal fluid being bounded by a closed surface. This interface does not intersect with the external boundary of the cloud. The proof is based on implicit function theorem and carried out in the Hölder spaces.

The phenomenon of decreased serum uric acid (UA) levels in patients with Parkinson’s disease (PD) and its relationship with purine metabolic pathways remain unclear. We compared inosine, hy-poxanthine, xanthine, and UA levels in serum and cerebrospinal fluid (CSF) of PD patients with those of controls, and investigated the effect of changes in the purine metabolic system on UA levels in PD. Overall, 134 samples (serum, 45 PD patients and 30 controls; CSF, 39 PD patients and 20 controls), were analyzed using liquid chromatography-tandem mass spectrometry. A general linear model (GLM) was used to investigate relationships among purine metabolites. Compared to controls, PD patients had significantly lower UA levels in the serum and CSF, and serum and CSF UA levels were significantly correlated. Additionally, in PD, decreased serum hypoxanthine levels were observed with decreased CSF inosine and hypoxanthine levels, suggesting the involvement of the purine recycling system. GLM analysis indicated that the reduced UA levels in PD were mainly due to sources other than the purine metabolic system, such as exercise, nutritional indices, muscle volume, or adipose tissue. Our results highlight the impairment of purine recycling pathways in PD, as evidenced by the decreased serum hypoxanthine and CSF inosine.

Numerical simulations of standard situations in the transition region from gas kinetics to fluid dynamics at small Mach numbers indicate a clear dependence of the simulation results on the underlying kinetic model (here: nonlinear and linearized Boltzmann collision operator vs. BGK relaxation model). We develop an improved mathematical framework (trace theory) to explain these differences. In particular we reveal certain deficiencies for the classical BKG system as well as for the standard Navier Stokes approach.

Abstract There is no research that combines behavioural and fMRI research approaches to investigate the mediating and moderating effects of working memory, verbal IQ, visuospatial and verbal reasoning on students’ performance of maths and science. This paper investigates all these multiple relationships between working memory (WM), verbal IQ, visuospatial and verbal reasoning with performance in maths and science accuracy. The multimethod research consists of a behavioural survey and a fMRI neuroscience investigating the interactive and multiple relationships of all cognitive processing independent variables (IVs) with the dependent variables (DVs) of maths and science performance. Using structural Equation Modelling (SEM) and Warp Partial Least Squares (Warp PLS) analytical approach, the research discusses the findings of both, the behavioural and fMRI data. The adolescent sample (N=34) for the behavioural and fMRI study, was recruited from consenting schools in London, UK, and consisted of equal numbers of girls and boys between 11-15 years old. The hypothesised behavioural SEM model predicted positive relationships between all the independent variables (IV) of visuospatial matrix reasoning (VSMatAR), verbal analogical reasoning (VerbAR), verbal working memory (VWM), visuospatial working memory (VSWM) and verbal IQ, with performance in maths and science accuracy. The findings support all hypotheses except two and identifies verbal IQ, Verbal WM and VerbAR as the three strongest predictors of maths and science accuracy. The neuroscience fMRI data identified four brain regions of interest, namely, the bilateral DLPFC, Parietal, Temporal and pre-supplementary motor area (PSMA) as being most relevant to maths and science outcomes. The hypothesised fMRI SEM, produced mixed results which supported some of the hypothesised relationships between the IVs of verbal AR and VSMatrix AR associations with all four brain regions and in turn the associations with maths and science performance. The paper makes two original contributions, firstly, by testing the hypothesis that Verbal WM mediates the independent variables’ effects on maths and science outcomes. And secondly, by using Warp PLS to test the SEM (behavioural and fMRI) models’ multiple non-linear interactions simultaneously between the IVs with the DVs of maths and science accuracy. The Warp PLS testing of all IVs and DVs produced some interesting new insights regarding the relationships between Verbal analogical reasoning, which are deemed important to assist academics and educational practitioners in improving maths and science performance of adolescent students. The combination of behavioural and neuroscience fMRI data provides more reliable empirical evidence regarding the multiple interactive influences impacting maths and science performance for adolescents.

Electrowetting – induced detachment of droplets from solid surfaces is important for numerous applications in the fields of heat transfer and fluid mechanics. The forced oscillations of droplets on solid surfaces and their ability to detach are studied. In this study the process is efficiently simulated by implementing a powerful methodology developed by our team. Our results agree with experiments, showing that optimal detachment, in terms of actuation energy, is achieved when the application of voltage is synchronized with the spreading time of the droplet. Under these conditions, the droplet oscillates with a period close to that of a mirrored Rayleigh droplet. The relation between the droplet’s oscillation period and its physical properties is examined. During voltage-droplet synchronization, the droplet’s ability to detach depends mostly on its contact angle, its viscosity, and the applied voltage. An energy analysis is also conducted, revealing how energy is supplied to the droplet by electrowetting-induced detachment.

Cambodian spices Amomum kravanh, Citrus hystrix and Piper nigrum 'Kampot' have long history of seasoning of food products. In this study, essential oils (EOs) and supercritical CO2 extracts from all three species have been analyzed using GC-MS with two columns of different polarity, whereas EO and CO2 extract from P. nigrum fruits and CO2 extract from the peel of C. hystrix have been isolated and analyzed for the first time. The results showed that A. kravanh EO contained mostly eucalyptol (78.8/ 72.6 %), while CO2 extract was rich in oleic acid (29.26 %) and tricosane (14.74 %). C. hystrix EO was rich in β-pinene (29.95/29.45 %), followed by D-limonene (24.54/23.24 %) and sabinene (9.94/10.23 %). β-pinene (30.2/28.9 %), D-limonene (23.99/23.74 %) and sabinene (13.36/19.55 %) were also predominant in the CO2 extracts. β-Caryophyllene was the main constituent of both EO and CO2 extract from P. nigrum 'Kampot' with contents ranging from 37.84 to 55.84 %, followed by 3-carene (from 7.18 to 18.72 %). Such findings suggest that supercritical CO2 can potentially be used for extraction of all three Cambodian spices. Nevertheless, further research determining the most efficient extraction parameters will be needed before its application in the spice processing practice.

Intracranial compliance (ICC) plays a pivotal role in understanding the underlying mechanisms of various brain disorders and is of great clinical importance. Therefore, addressing the challenges in practical application of ICC is crucial for neurosurgeons. This study explored the significance of ICC assessment considering the time-dependency of specific brain disorders through two distinct approaches: short and large time elapsed (TE) in measuring volume or intracranial pressure (ICP) changes in the ICC equation (∆Volume/∆ICP). Variations in ICC values were observed across various ICC assessment methods and different TE values. Notably, the compensatory response of the brain exhibited non-monotonic and variable changes in a large TE for certain brain disorders, diverging from patterns observed in short TE assessments. Furthermore, the recovery behavior of the brain changed under different brain disorders when exposed to short and long TE conditions. These findings emphasized the dynamic nature of ICC and provided valuable insights into the correct practical assessment of ICC by selecting the appropriate TE, as well as considering the differences in strain rates and loading durations on the brain in different brain disorders. These insights also shed light on the reasons why, despite its clinical significance, ICC monitoring has not yet become a standard component of clinical care, unlike ICP monitoring.

Our previous studies showed that in patients with brain diseases neurotrophic factors in lacrimal fluid (LF) may change more prominently than in blood serum (BS). Since glial cell line-derived neurotrophic factor (GDNF) is involved in control of neuronal networks in epileptic brain, we aimed to assess GDNF levels in LF and BS as well as BDNF, hypothalamic-pituitary-adrenocortical and inflammation indices in BS of patients with focal epilepsy (PWFE), epilepsy and comorbid depression (PWFE+MDD) compared with major depressive disorder (PWMDD) and healthy controls (HC). GDNF levels in BS were similar in patients and HC and higher in PWFE taking valproates. GDNF levels in LF were significantly lower in all patient groups compared to controls, and independent of drugs used. LF and BS GDNF concentrations positively correlated in HC, but not patient groups. BDNF level was lower in BS of patients compared with HC and higher in PWFE+MDD taking valproates. Logistic regression models demonstrated that GDNF decrease in LF may be an important predictor of focal epilepsy. Probability of focal epilepsy can be evaluated using GDNF in LF and BDNF in BS; MDD - GDNF in LF, cortisol and TNF-α in BS; epilepsy with MDD - GDNF in LF, TNF-α and BDNF in BS.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

Introduction: An increasing body of evidence shows the significant role of the angiogenic factor levels in screening of pregnancy outcome. Purpose: To examine the potential relationship between concentrations of placental protein 13 (PP13) and soluble Human Leukocyte Antigen-G (sHLA-G) in maternal serum and amniotic fluid at 16-23 weeks of gestation and the sonographic features of pregnancy as well as pregnancy outcome. Materials and methods: PP13 and sHLA-G in serum and amniotic fluid, and fetal biometrical data and placental volume and perfusion indices were determined in 71 euploid, singleton pregnancies. Results: The serum sHLA-G level correlated negatively with serum PP13 level (r = -0.186, p&lt;0.001) and positively with sHLA-G level in the amniotic fluid (r = 0.662, p&lt;0.001). Significant correlation was found between serum sHLA-G level and placental volume (r = 0.142, p&lt;0.05) and between amniotic sHLA-G level and placental perfusion (r = -0.450, p&lt;0.001). A low amniotic PP13 level significantly predicted the birth weight (r = -0.102, p&lt;0.05), the duration of pregnancy (r = -0.155, p&lt;0.05), and the fetal abdominal circumference (r=-0.098, p&lt;0.05). Conclusions: PP13 assayed in amniotic fluid might be a potential marker of fetal growth and sHLA-G can be an adjunct modality reflecting placental sonographic parameters.

Magnetorheological (MR) fluids have been known to react to magnetic fields of sufficient magnitudes. While in the presence of the field the material develops a yield stress. The tunable property has made it attractive in e.g. semi-active damper applications in vibration control domain in particular. Within the context of a given application the fluids can be exploited in at least one of the fundamental operating modes of which the so-called gradient pinch mode has been least explored. Contrary to the other operating modes, the MR fluid volume in the flow channel is exposed to a non-uniform magnetic field in such a way that the Venturi-like contraction is developed in a flow channel solely by means of a solidified material in the regions near the walls rather than mechanically driven changes of the channel’s geometry. The pinch mode rheology of the material has made it a potential candidate in developing on a new category of MR valves. By convention, a pinch mode valve features a single flow channel with poles over which non-uniform magnetic field is induced. In this study the authors examine ways of extending the dynamic range of pinch mode valves by employing a number of such arrangements (stages) in series. To accomplish this, the authors developed a prototype of a multi-stage (three-stage) valve, and then compared its performance against that of a single-stage valve across a wide range of hydraulic and magnetic stimuli. To summarize, improvements in the pinch mode valve dynamic range are evident, however, at the same time it is hampered by the presence of serial air gaps in the flow channel.

Objective: To observe the effect of the combination of fluid-increasing decoction, low molecular heparin sodium and aspirin in the treatment of oligohydramnios in pregnancy. Methods: In this study, 114 pregnant women with oligohydramnios during pregnancy admitted to our hospital between May 2019 and March 2022 were selected as objects, and the pregnant women were equally divided into the observation group and the experimental group by random number table method, with 57 cases in each group. The observation group received conventional fluid infusion, low molecular heparin sodium and aspirin, while the experimental group was treated with fluid-increasing decoction on the basis of the observation group. The treatment effect, S/D level, amniotic fluid index, maximum vertical pocket (MVP), coagulation indexes (plasma prothrombin time (PT), plasma activated partial thromboplastin time (APTT), fibrinogen (FIB)), pregnancy outcome and adverse reactions were compared between the two groups. Results: The total effective rate of treatment was obviously better in the experimental group than that in the observation group (P＜0.05); the S/D level after treatment in the experimental group was remarkably lower than that in the observation group (P＜0.05). The amniotic fluid index and MVP were remarkably higher in the experimental group than in the observation group after treatment (P < 0.05). No significant differences in PT, APTT and FIB were found between the two groups before and after treatment (P > 0.05). The rate of oligohydramnios at delivery, cesarean section rate, neonatal weight status and preterm delivery rate were dramatically better in the experimental group than in the observation group (P < 0.05). Post-partum haemorrhage rate, neonatal asphyxia rate, amniotic fluid contamination rate and incidence of adverse events were not significantly different between the two groups of pregnant women (P > 0.05). Conclusion: The combination of fluid-increasing decoction, low molecular heparin sodium and aspirin is clinically effective and safe in the treatment of pregnant women with oligohydramnios during pregnancy. The combination is effective in reducing the S/D ratio of fetal umbilical blood flow, enhancing the amniotic fluid index and MVP in pregnant women with oligohydramnios during pregnancy, whilst not adversely influencing the coagulation function of the mother, thus contributing to a reduction in the risk of adverse pregnancy outcomes.

Autonomous Underwater Vehicles (AUVs) are emerging as pivotal tools in underwater applications such as seafloor exploration and the inspection of pipelines or cables. Traditional land-based avoidance methods prove insufficient when applied to the complex underwater environment, largely due to the unique constraints presented by marine environments and the specific dynamics of AUVs. In this study, we introduce an improved stream function-based obstacle avoidance algorithm specifically tailored for autonomous underwater vehicles. The proposed algorithm is based on a stream function that is derived from the stream function. The stream function is characterized by a radial histogram for the cost function. In addition, constraints related to the maximum path curvature are discussed to optimize the utility of the path. Our exhaustive simulation cases validate the robustness and adaptability of the proposed algorithm, demonstrating its ability to produce feasible and optimized avoidance paths in a variety of scenarios.

One of the operational challenges for the use of bentonite pellets as a sealing material in the abandonment of offshore fields consists in their disposition inside the well. This study aims to analyze the interaction of fluid media, consisting of saline solutions (NaCl, CaCl2 and KCl) and organic compounds (diesel, glycerin and olefin), with bentonite pellets, aiming its application as displacement fluid in offshore oil well abandonment operations. The physical integrity of the bentonite pellets in contact with the fluids was verified through visual inspections and dispersibility tests. Linear swelling tests were also performed to evaluate the potential for swelling of pellets in deionized water after contact with the fluid media. The results indicated that NaCl, CaCl2 and KCl solutions completely compromise the physical integrity of the pellets, while diesel and olefin showed the best responses regarding the structural preservation. Futhermore, the linear swelling tests showed that, even after the contact with diesel and olefin for 1 hour, bentonite pellets have reached a total swelling in water of 78%, after 24 hours. In this way, diesel and olefin proved to be highly promising alternatives to be used as displacement fluids for bentonite pellets in wells to be abandoned in a submarine environment.

In previous papers we have shown how Schrödinger’s equation which includes an electromagnetic field interaction can be deduced from a fluid dynamical Lagrangian of a charged potential flow that interacts with an electromagnetic field. The quantum behaviour was derived from Fisher information terms which were added to the classical Lagrangian. It was thus shown that a quantum mechanical system is driven by information and not only electromagnetic fields. This program was applied also to Pauli’s equations by removing the restriction of potential flow and using the Clebsch formalism. Although the analysis was quite successful there were still terms that did not admit interpretation, some of them can be easily traced to the relativistic Dirac theory. Here we repeat the analysis for a relativistic flow, pointing to a new approach for deriving relativistic quantum mechanics.

Modeling the flow of polymer solutions requires knowledge at various length and time scales. The macroscopic behavior is described by the overall velocity, pressure and stress. The polymeric contribution to the stress requires knowledge of the evolution of polymer chains. In this work, we use a microscopic model, the finitely extensible nonlinear elastic (FENE) model, to capture the polymer behavior. The benefit of microscopic models is they remain faithful to the polymer dynamics without information loss via averaging. The downside is the computational cost needed to solve the thousands to millions of differential equations describing the microstructure. We thus describe a multiscale flow solver that utilizes GPUs for massively parallel, efficient simulations. We compare and contrast the microscopic model with its macroscopic counterpart under various flow conditions. In particular, significant differences are observed under nonlinear flow conditions, where the polymers become highly stretched and oriented.

Overhydration (OH) is a prevalent medical problem occuring in patients with kidney failure, but a specific marker has still not been found. Currently, clinicians employ techniques such as bioimpedance spectroscopy (BIS), ultrasound (US) markers of fluid overload or markers of heart and kidney function such as NT-pro-BNP, GFR or creatinine levels. New serum markers, including but not limited to Ca-125, Galectin-3 (Gal-3), Adrenomedullin (AMD) and Urocortin-2 (UCN-2), are presently under research, displaying promising results. The necessity to ascertain a more precise marker of overhydration is urgent mainly because physical examination is exceptionally imprecise. Signs and symptoms of fluid overload, like edema or gradual increase of body mass, are not always present, notably in patients with chronic kidney disease. This review paper summarizes actual knowledge of a patient's hydration status estimation, focusing specifically on kidney diseases.

Demand for nutmeg essential oil in Indonesia and the world is increasing. Nutmeg essential oil is obtained from young nutmeg seeds extracted by water steam distillation (WSD). The weakness of the extraction process with WSD is the long distillation time (24 hours), wasteful of fuel, wasteful of manpower, produces polluting gases which damage the environment and requires a lot of water as a coolant. The purpose of this study was to compare the WSD and SCFE methods for extracting nutmeg essential oil. The research was conducted by extracting nutmeg essential oil using two methods are WSD and SCFE. The results showed that the chemical composition of the nutmeg essential oil produced by the two methods was almost similar. Nutmeg essential oil produced by both methods shows the same characterization. The yield between the two methods is almost the same, in the range of 10-12% using extraction time 15-60 minutes. The SCFE method has advantages over WSD are a faster extraction time, does not require heating materials and CO2 gas can be reused. In conclusion, SCFE is an alternative method to increase the production of nutmeg oil.

In natural, laboratory and industrial conditions, the density of a fluid or gas, depending on temperature, pressure, concentration of dissolved substances or suspended particles, changes under the influence of a large number of physical factors. We assume that undisturbed liquid is stratified. The analysis is based on a system of fundamental equations for the transfer of energy, momentum and matter in periodic flows of a viscous compressible fluid. The propagation of periodic flows in viscous uniformly stratified fluids is considered. Taking into account the compatibility condition, dispersion relations are constructed for two-dimensional internal, acoustic and surface linear disturbances with a positive definite frequency and complex wave number in a compressible viscous fluid exponentially stratified by density. The temperature conductivity and diffusion effects are neglected. The obtained regularly perturbed solutions to the equations describe weakly damped waves. Singular solutions characterize the thin ligaments that accompany each type of wave. In limiting cases, the constructed solutions transform into known expressions for a viscous homogeneous and ideal fluid or degenerate.

This research, which focuses on wave energy generating technology, suggests a brand-new oscillating float-type wave energy conversion system that is appropriate for the offshore wave environment. To accurately model the device, a three-dimensional viscous numerical pool is created based on STAR-CCM+. The array-type power generation device is numerically simulated using theoretical analysis and numerical simulation, and the wave energy power generation device is arranged as double floats in the front and rear rows, representing triangular array type and rectangular array type, respectively. The triangular array type is a superior layout and can make greater use of marine resources, according to this paper's analysis of the hydrodynamic and power generation impacts of the three array types. The findings are meant to serve as a guide for engineering practice.