Micro-Raman spectroscopy was carried out to evaluate the localized residual stresses in commercial Gallium Nitride-based devices, specifically AlGaN/GaN High Electron Mobility Transistors (HEMTs) in a novel packaging design provided by STMicroelectronics S.r.l. The packaging plays a key role in protecting the device core against the external environment, thus minimizing damages caused by mechanical shocks, exposure to light, and contact with chemicals, conjointly achieving an efficient heat dissipation rate. Even though the packaging is a required step for the proper functioning of ready-to-use electronic devices, its application typically may introduce mechanical stress to AlGaN/GaN HEMTs, which can result in various reliability issues. In this paper, we investigate the impact of packaging on residual stress by analyzing the frequency shift of the E2 Raman peak along GaN layers and at the GaN/Si interface. An extensive evaluation was conducted using both a packaged device and a wafer-level device. The correlation between Raman frequency shifts of the E2 mode was accurately quantified, revealing a stress mitigation of approximately 0.1 GPa. This reduction is ascribed to the compressive stress introduced by the packaging, which partially offsets the intrinsic tensile stress of the wafer-level device. The proposed methodology could, in principle, be implemented to improve the development of a packaging.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

1) Background: Capturing patients’ medical histories significantly influences clinical decisions. Errors in this process lead to clinical errors, increase costs and dissatisfaction among physicians and patients. Physicians in developing countries are overloaded with patients and cannot always follow the proper history-taking procedure. The challenges are acknowledged; however, a comprehensive understanding of the status and the remedies remained unexplored. 2) Objective: This paper aims to investigate the workload, history-taking challenges, and the willingness of the physicians to accept digital solutions. 3) Methods: A cross-sectional online survey was conducted on 104 physicians across Bangladesh, featuring 22 questions regarding their professional environment, workload, digitization status of health records, challenges in history-taking, and attitudes toward adopting digital solutions for managing patient histories; 4) Results: 92.67% of the physicians face workloads, 88.46% struggle in medical history-taking, and only 4.81% use digital medical records. About 70% struggle to complete the necessary history-taking steps, emphasizing the urgent need for solutions. An AI-based Smart Health Gantt Chart (SHGC) system has been introduced for their instant feedback. 93.27% of physicians expressed their willingness to use such a system. 5) Conclusions: The proposed SHGC has the potential to enhance healthcare efficiency in developing nations, benefit physicians, and improve patient-centered care.

The collaboration of multimodal transport documents is the foundation for conducting multimodal transport operations. Blockchain technology can effectively address trust issues and information sharing difficulties in current multimodal transport document collaboration. However, in current blockchain-based electronic document research, the bottleneck problem lies in the collaboration of multiparty in multimodal transport under the "one-bill coverage system". We design a blockchain platform architecture for multimodal transport, reshaping collaboration processes for different modes of transport based on the blockchain platform. It proposes a collaboration model for multimodal transport under the "one-bill coverage system" and performs model solving and case analysis. The obtained collaboration strategies are embedded into the platform's application layer. Finally, using Solidity language, it writes smart contracts related to multimodal transport under the "one-bill coverage system " and deploys and executes them on the Remix platform.

Volatile organic compounds (VOCs) released from plants have been correlated with disease-status. Analysis of VOCs using GC-MS is time-consuming, laboratory-based, and requires specialist training. Electronic nose devices (E-nose) provide a portable alternative. Three different E-nose devices were compared to assess how accurately they could detect Mango Twig Tip Dieback and Panama disease in banana. The devices were initially trained on known volatiles, then pure cultures of Pantoea sp., Staphylococcus sp., and Fusarium odoratissimum, and finally, on infected and healthy mango leaves and field-collected, infected banana pseudo-stems. The experiments were repeated three times with six replicates for each host-pathogen pair. The variation between healthy and infected host materials was evaluated by principal component and linear discriminant analysis, cross-validation and chemometric data analysis. GC-MS analysis was conducted contemporaneously and identified an 80% similarity between healthy and infected plant material. The portable C 320 was 100% successful in discriminating known volatiles but had a low capability in differentiating healthy and infected plant substrates. The advanced devices (PEN 3 / MSEM 160) successfully detected healthy and diseased samples with a high variance. The results suggest that E-nose devices are more sensitive and accurate in detecting changes of VOCs between healthy and infected plants compared to headspace GC-MS.

This paper constituted an extension of two previous studies concerning the mathematical development of the grain boundary grooving in polycrystalline thins films in the cases of the evaporation/condensation and diffusion taken separately. The thermal grooving processes are deeply controlled by the various mass transfer mechanisms of evaporation–condensation, surface diffusion, lattice diffusion, and grain boundary diffusion. This study proposed a new original analytical solution to the mathematical problem governing the grain groove profile in the case of simultaneous effects of evaporation-condensation and diffusion in polycrystalline thin films submitted to thermal and mechanical stress, and fatigue effects; by resolving the corresponding fourth-order partial differential equation ∂y∂t=C∂2y∂x2-B∂4y∂x4 obtained from the approximation y'2≪1. The comparison of the new solution to that of diffusion alone proved an important effect of the coupling of evaporation and diffusion on the geometric characteristics of the groove profile. A second analytical solution based on the series development was also proposed. It was proved that change of the boundary conditions of the grain grooving profile largely affected the different geometric characteristics of the groove profile.

Hybride halide perovskite materials gain enormous attention for their semiconducting properties, higher power conversion efficiency and potential applications in a wide range field of studies along with their two key limitations: stability and toxicity. In spite of great progress made on the halide perovskites and many promising research developments, overcoming these limitations is not realized yet. Therefore, coordination engineering of new framework for obtaining alternative new halide perovskite materials and fundamental understanding of the coordination chemistry and electronic interactions forming the structure of these newly engineered halide perovskite materials might be one way in order to overcome the issues related to both stability and toxicity. In this review, the current development of halide perovskite families, both lead halide perovskites and lead free halide perovskites followed by coordination engineering of the new frameworks to engineer new halide perovskite materials will be reviewed comprehensively. Moreover, all the concerns of the fundamental ideas of coordination chemistry and electronic interactions that are keys in forming the halide perovskite structures are discussed in detail and form the main aim of this review. Interestingly, we also discuss recent potential energy applications beyond photovoltaic and this review has completed with an essential and open question: ‘what could happen in the future of halide perovskites?’ in order to excite commercial enterprises and research institutions again as well as to get motivating new predictions on the future continuity of this field.

Due to its large hole mobility, Organic Rubrene (C42H28) has attracted research questions on its applications in electronic devices. In this work, extensive first-principles calculations were made to predict some temperature and doping dependent properties of Organic Semi- conductor Rubrene. We use Density Functional Theory (DFT) to investigate the electronic structure, elastic and transport properties of the Orthorhombic phase of the Rubrene compound. The calcu- lated band structure shows the Orthorhombic phase has a direct bandgap of 1.26 eV. From the Vickers hardness (1.080 GPa), our calculations show that Orthorhombic Rubrene is not a super hard material and can find useful application as a flexible semicon- ductor. The calculated transport Inverse Effective Mass and Elec- tronic Fitness Function show that the Orthorhombic Rubrene Crystal Structure is a p-type thermoelectric material at high temperatures.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

: Considering that Einstein's relation between the diffusion coefficient and the drift mobility of the free randomly moving charge carriers in homogeneous materials including metals is always valid, it is shown that the effective electric force acting on free electrons in metal depends on the ratio between the kinetic free electron energy at the Fermi surface to the classical particle energy 3kT/2. The electrical resistivity of elemental metals dependence on very low temperatures has the quadratic term, which has been explained by electron-electron scattering. In this paper, it is shown that the quadratic term of the electrical resistivity at low temperatures is caused by scattering of the free RM electrons by electronic defects due to linear effective free electron scattering cross-section dependence on temperature, but not by electron-electron scattering.

Sustainable supply chain management (SSCM) represents a critical strategy for the electronics industry to balance economic objectives with environmental and social responsibility across complex global production networks. This multiple case study analysis investigates SSCM integration within leading Korean electronics manufacturers Samsung, LG, and Hyundai. In-depth qualitative data, focus groups, and sustainability report analysis reveals the policies, practices, results and implementation barriers related to incorporating sustainability criteria across procurement, manufacturing, distribution and recycling functions. Findings show sustainability considerations increasingly driven by cost, risk, reputational and regulatory factors, with vertical coordination initiatives helping transfer knowledge to assist suppliers on compliance and emissions reductions. Yet substantial obstacles persist around monitoring, coordination, transparency and technical capabilities, especially amongst lower tiers. The paper discusses how common reporting standards, ethical sourcing certification and partnerships can accelerate electronics supply chain sustainability. By mapping integration achievements and gaps, this study informs managerial best practices and policy reforms toward promoting socially and ecologically responsible models for Korea's vital export industry as it navigates rising stakeholder pressures.

The structural, elastic, and electronic properties of orthorhombic Cd2SiO4 and Hg2GeO4 were examined under varying pressure conditions using first-principles calculations based on densi-ty-functional theory employing the projector augmented wave method. The obtained cell pa-rameters at 0 GPa were found to align well with existing experimental data. We delved into the pressure-dependence of normalized lattice parameters and elastic constants. In Cd2SiO4, all lat-tice constants decreased as pressure increased, whereas in Hg2GeO4, parameters a and b de-creased while parameter c increased under pressure. Employing the Hill average method, we calculated the elastic moduli and Poisson’s ratio up to 10 GPa, noting an increase with pressure. Evaluation of ductility/brittleness under pressure indicated both compounds remained ductile throughout. We also estimated elastic anisotropy and Debye temperature under varying pres-sures. Cd2SiO4 and Hg2GeO4 were identified as indirect band gap insulators, with estimated band gaps of 3.34 eV and 2.09 eV, respectively. Interestingly, Cd2SiO4 exhibited a significant increase in band gap with increasing pressure, whereas the band gap of Hg2GeO4 decreased under pres-sure, revealing distinct structural and electronic responses despite their similar structures.

Thromboprophylaxis of hospitalized patients at risk of venous thromboembolism (VTE) presents challenges owing to patient heterogeneity and lack of adoption of evidence-based methods. Intuitive practices for thromboprophylaxis have resulted in many patients being inappropriately prophylaxed. Multiple interventions for thromboprophylaxis have been tested, including use of multifaceted approaches such as national VTE prevention programs with audits, use of passive alerts (either human or electronic), and more recently use of active clinical decision support (CDS) tools incorporated into electronic health records (EHRs). Multifaceted health-system interventions have shown mixed results in their ability to increase appropriate thromboprophylaxis and reduce VTE, unless mandated through a national VTE prevention program, though the latter approach is potentially costly, effort- and time-dependent. Studies utilizing passive human or electronic alerts have also shown mixed results in increasing appropriate thromboprophylaxis and reducing VTE. The use of active CDS tools holds the greatest promise, especially with further refinement and widespread implementation within various EHRs and clinical workflows. Recent-ly a universal cloud-based and EHR-agnostic CDS VTE tool revealed high adoption and effectiveness in increasing appropriate thromboprophylaxis and reducing major thromboembolism. This narrative review summarizes the literature on system-wide thromboprophylaxis interventions in hospitalized patients, with a focus on CDS tools.

A substantial spike in the need for quality healthcare has resulted from people being more cognizant of health issues. With blockchain, healthcare providers may safely share patient information electronically, which is especially important given the sensitive nature of the data contained inside them. However, flaws in the current blockchain design have surfaced since the dawn of quantum computing systems. The study proposes a novel quantum inspired blockchain system (Qchain) and constructs a unique entangled quantum medical record (EQMR)system with an emphasis on privacy and security. This Qchain relies on entangled states to connect its blocks. Automated production of the chronology indicator reduces storage capacity requirements by connecting entangled BloQ (blocks with quantum properties) with controlled activities. One qubit is used to store the hash value of each block. A lot of information regarding quantum internet is included in the protocol for the entangled quantum medical record (EQMR). EQMR can be accessed in Medical Internet of Things (M-IoT) systems may be kept private and secure, and their where-abouts can be monitored in the event of an emergency. The protocol also uses quantum authentication in place of more conventional methods like encryption and digital signatures. Mathematical research shows that the quantum converged blockchain (QCB) is highly safe against attacks such as the External attack, Intercept-Measure-Repeat attack, and Entanglement-Measure attack. The reliability and auditability evaluations of the entangled BloQ, as well as the quantum circuit design for computing the hash value, are presented. There's also a comparison between the suggested approach and several other quantum blockchain designs.

Chrysanthemum tea, a typical health tea with the same origin as medicine and food, is famous for its unique health benefits and flavor. To clarify the influence of metabolites of different varieties of chrysanthemum tea on the formation of taste and quality differences, nontargeted metabolomics combined with electronic tongue analysis were used to characterize the correlation between metabolites profiles and taste characteristics of different quality chrysanthemum tea. Thirteen metabolites were identified as the key metabolites of the sensory quality difference between Huangju and Jinsi Huangju tea. Kaempferol, luteolin, genistein, and some quinic acid derivatives were correlated with the ‘astringent’ and taste attributes. In contrast, l-(-)-3 phenyllactic acid and L-malic acid were found to be the ‘bitterness’ and ‘umami’ in chrysanthemum tea. KEGG pathway enrichment analysis showed that the flavonoid and flavonol biosynthesis pathway had important effects on the sensory quality of chrysanthemum tea.

Electronic waste (e-waste), characterized by the widespread disposal of electronic devices, shows a growing environmental challenge. In this study, we explore the electrocatalytic potential of gold nanoparticles supported on Vulcan obtained from e-waste for their application as electrocatalysts for the methanol oxidation reaction in alkaline media. Gold nanoparticles are synthesized from gold coatings recovered from Intel Pentium 4 processor pins, highlighting their sustainability as electrocatalyst precursors. Comprehensive characterization, including UV-Vis spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray dif-fraction, is performed to assess the electrocatalyst's structural properties. Electrochemical evalu-ation is carried out in 0.5 M KOH electrolyte employing the rotating disk electrode technique, us-ing cyclic voltammetry for the study of methanol oxidation. Remarkably, the gold nanoparticles show electrocatalytic activity on par with commercially synthesized counterparts, demonstrating the feasibility of this approach for sustainable electrocatalyst production. Thus, this research opens new routes for utilizing e-waste as a source of valuable catalyst materials, addressing en-vironmental and technological challenges in the field of alkaline fuel cells.

Aeromagnetic compensation plays a vital role in geomagnetic navigation and has received considerable attention throughout last few decades. Classical aeromagnetic compensation methods based on the Tolles–Lawson (T-L) model are mainly aimed at permanent, induced, and eddy-current magnetic interferences of aircraft platform, which ignores other stray magnetic field interference on the platform including the interferences caused by on-board electronic (OBE) systems. In order to cooperate with TL model, magnetometers are usually required to be installed on the extension rod outside the cabin, which is widely applied to geophysical magnetic survey. In order to ensure safety and reduce the cost of platform modification in geomagnetic navigation, it’s necessary to place magnetometers inside the cabin. It also further exacerbates the magnetic interferences and improves the difficulty of magnetic compensation. In this paper, a modified aeromagnetic compensation method is proposed, and the in-cabin OBE interferences are respectively modelled to be proportional to the currents and their temporal variations of different electronic devices. To ensure that modified model adapts to strong OBE interference in the cabin, a cut-off frequency determination method based on curvature calculation and a feature selection method based on correlation calculation are proposed. The cut-off frequency determination method helps to select passband filter which suitable for in-cabin OBE interference. The feature selection method can help to effectively select current and voltage inputs for modified model. In addition, principal component analysis (PCA) is adopted to reduce multicollinearity which is intensified by the extension of OBE interferences in coefficient-estimating. Experiments on public dataset are conducted to illustrate the effectiveness of the proposed method, and the best compensation result achieved 1.71nT of root mean square error (RMSE).

This scientific paper presents a comprehensive investigation into transient Fourier analysis in some electrical engineering applications. The article deals with two effective approaches for solving transient analysis whose application is rather novel. The first contribution uses combined the Fourier series analytic Laplace-Carson (L­C) transform methods in the complex domain using complex time vectors, thereby significantly simplifying the calculation of the original function. As the inverse transform goes back into the time domain, it employs the Cauchy-Heaviside (C­H) method. The second contribution uses the Fourier transform (F­Τ)for transient analysis of a power converter electrical circuit with the passive and the active load. The method of complex conjugated amplitudes is used for steady-state analysis. Both contributions represent a new approach to this paper. The starting point is the Fourier series/expansions, computation of the Fourier coefficients, then continuing by solving the steady and transient states of the system and confirming the transient states using the Fourier transform. To validate our findings, the worked-out analytical results are verified by modelling in Matlab/Simulink environment.

The electronic nose (e-nose) is an innovative device that mimics the human olfactory system, allowing for the detection and identification of numerous scents. This abstract gives an in-depth examination of the current status of electronic nose technologies, with an emphasis on sensing mechanisms, applications, and recent breakthroughs. The research delves into the many uses of e-nose, such as food quality control, environmental monitoring, medical diagnostics, and industrial operations. It also covers the problems and potential future applications of electronic nose technology. The literature review highlights the importance of this technology in improving our capacity to evaluate complex scents in several domains.

In this computational study, we investigate the electronic properties of zigzag graphene nano-parallelograms (GNPs), which are parallelogram-shaped graphene nanoribbons of various widths and lengths, using thermally-assisted-occupation density functional theory (TAO-DFT). Our calculations reveal a monotonic decrease in the singlet-triplet energy gap as the GNP length increases. The GNPs possess singlet ground states for all the cases examined. With the increase of GNP length, the vertical ionization potential and fundamental gap decrease monotonically, while the vertical electron affinity increases monotonically. Besides, as the GNP length increases, the symmetrized von Neumann entropy increases monotonically, denoting an increase in the degree of multi-reference character associated with ground-state GNPs. The occupation numbers and real-space representation of active orbitals indicate that there is a transition from the nonradical nature of the shorter GNPs to the increasing polyradical nature of the longer GNPs. In addition, the edge/corner localization of active orbitals is found for the wider and longer GNPs.

The purpose of water treatment through ultraviolet (UV) radiation is to interrupt the development and multiplication of microorganisms by preventing their growth and reproduction.Ultraviolet treatment has become a very affordable solution to produce clean water of optimal quality in regions where access to drinking water is essential. The experimental water treatment unit is powered by a photovoltaic (PV) source. It incorporates a discharge lamp used to generate ultraviolet radiation, which is harnessed to address bacteriological issues related to water quality. This lamp is continuously powered by a photovoltaic (PV) source through an inverter and an electronic ballast. The water treatment system also includes a motor pump designed to draw contaminated water from the input reservoir, a flow control valve to adjust flow rates as needed, and a filter aimed at enhancing the quality of the contaminated water. The water circulates between the input reservoir (contaminated water) and the output reservoir (treated water) through the UV lamp. The relationship between the intensity of the UV lamp and the water flow rate can ensure an adequate water quality.

Polyanilines are a class of conductive polymers that have attracted significant interest in the field of organic electronics due to their unique properties. In this article, the fluorescence spectroscopy and photovoltaic properties of polyaniline-based thin films and copolymers are investigated. The study focuses on understanding the relationship between the composition and structure of polyanilines and their optical and electrical properties. The article discusses the results of experiments on the photoluminescent properties of S1-S9 copolymers in a DMSO solution and of thin-film photoresistors based on polyanilines. The findings reveal that the photovoltaic properties of the thin films depend on the conditions of their fabrication and their surface morphology. The solubility of polyanilines is excellent, making the production of electronic components compatible with modern printing technologies in organic electronics. The work also points out that the photoconductivity of polyanilines can be improved by incorporation of additional molecular groups into the polymer matrix. Overall, this study sheds light on the potential of polyanilines as promising materials for organic electronics and provides insights into how their properties can be optimized for specific applications.

Advances in biomimetic triboelectric nanogenerators (TENGs) have significant implications for electronic skin (e-skin) and human-machine interaction (HMI). Emphasizing the need to mimic complex functionalities of natural systems, particularly human skin, TENGs leverage triboelectricity and electrostatic induction to bridge the gap in traditional electronic devices' responsiveness and adaptability. The exploration begins with an overview of TENGs' operational principles and modes, transitioning into structural and material biomimicry inspired by plant and animal models, proteins, fibers, and hydrogels. Key applications in tactile sensing, motion sensing, and intelligent control within e-skins and HMI systems are highlighted, showcasing TENGs' potential in revolutionizing wearable technologies and robotic systems. This review also addresses the challenges in performance enhancement, scalability, and system integration of TENGs. It points to future research directions, including optimizing energy conversion efficiency, discovering new materials, and employing micro-nanostructuring techniques for enhanced triboelectric charges and energy conversion. The scalability and cost-effectiveness of TENG production, pivotal for mainstream application, are discussed along with the need for versatile integration with various electronic systems. The review underlines the significance of making bioinspired TENGs more accessible and applicable in everyday technology, focusing on compatibility, user comfort, and durability. Conclusively, it underscores the role of bioinspired TENGs in advancing wearable technology and interactive systems, indicating a bright future for these innovations in practical applications.

Abstract Introduction: An important indicator of a hospital's quality of care is the frequency of visits to the emergency department (ED). If a patient returns to the emergency room (ED) shortly after being evaluated or treated, it is generally assumed that their initial evaluation or treatment was inadequate. Objectives: The purpose of this study is to identify the main reasons for patient revisits to the emergency department in Hail. Studies suggest that researchers usually report the reasons for revisiting patients after 72 hours to patients themself. Therefore, alternative hypotheses will attribute the reasons to the system or physician's skill. To test these hypotheses, a methodology was developed. Method: The study analyzed patients discharged from King Khalid Hospital within 72 hours of discharge, involving all adults, regardless of health status or location Results: In February 2019, 17461 ED visits occurred, with 11% returning within 72 hours. In February 2022, 880 of 8749 visits resulted in a 10% return visit, with 30 randomly selected return visits.Conclusion: Increased community awareness post-COVID-19 may explain differences in ED revisit rates between 2022 and 2019, with system errors and patient information re-entry being associated

We offered the circuit of a discrete analog filter (DAF) low frequencies of second-order on switchable capacitors, which differs from the known ones in that three capacitors with one terminal are connected to a common bus, and the frequency of the DAF pole depends not only on the ratio of the capacitances of the frequency-setting capacitors, but also on the ratio of resistances two additional resistors in the feedback. This allows at constant values ​​of the capacitances and a fixed switching frequency of electronic switches, control the pole frequency by changing the resistance ratio of additional resistors. Computer simulation of the developed circuit was performed in the Micro-Cap environment. It has been established that the DAF has a transmission coefficient close to minus one at very low frequencies and a transmission coefficient close to zero at higher frequencies.

Background: Patients with infectious complications related to the presence of cardiac implantable electronic devices (CIED) constitute a heterogeneous group, including local pocket infection (PI) and lead related infectious endocarditis (LRIE). The diagnosis of CIED-related infection is often difficult and requires complex imaging and microbiological tests. The aim of the current study was to evaluate the usefulness of new simple hematological parameters in detecting infectious complications in patients with CIED and assessing their extent. Methods: The retrospective analysis of clinical data of 2909 patients (36.37% with CIED-related infections), undergoing transvenous lead extraction (TLE) procedures in three high-volume centres in the years 2006-2020, was conducted. The sensitivity and specificity of new hematological markers were evaluated: the neutrophil to lymphocyte ratio (NLR), neutrophil to platelet ratio (NPR), and lymphocyte to platelet ratio (LPR) in the diagnosis of infectious complications, assessment of the spread of the infectious process and differentiation of additional structures related to the presence of leads. Results: In patients with CIED infections, compared to the non-infectious group, high inflammatory parameters were confirmed, and the highest specificity of the new markers in detecting the infectious process was demonstrated. (79.47% for NPR and 72.82% for NLR). Analysis of laboratory parameters in infectious and non-infectious patients with the presence of additional lead-related masses showed the highest specificity of NPR (82,78%) in predicting the diagnosis of vegetation. Comparison of laboratory parameters in patients with LRIE and PI showed higher NLR % (4.24 vs 2.56; p<0.001, area under curve (AUC) in a receiver operating characteristic (ROC) curve: 0.67 and 0.78 respectively) and higher NPR (0.03 vs 0.02; p<0.001; AUC: 0,51 and 0,55) in patients with LRIE. The highest sensitivity in the detection of coexistence LRIE with PI has been demonstrated for NLR (87.33%). Conclusions: Novel hematological markers may be helpful in the recognition of the inflammatory process in patients with CIED, differentiation of vegetation and vegetation-like masses, and the extent of infection in patients with PI.

The work carried out first-principles calculations within the framework of density functional theory to study the structural stability of the CsSnI₃ compound and the influence of phase transitions on their electronic and optical properties. Using the GGA and SCAN functionals, the relaxed structures of the CsSnI₃ phases were obtained and their geometric characteristics were assessed. Using the Phonopy code based on VASP, calculations of phonon and thermodynamic properties were performed, and the temperatures of phase transitions of CsSnI₃ were determined. The temperature dependences of the thermodynamic parameters α-, β-, γ- and δ-phases of CsSnI₃ were analyzed. The trends in free energy, entropy, enthalpy, heat of formation energy and heat capacity were justified in terms of the pattern of changes in the total energy of the four phases of CsSnI₃ from VASP calculations. It is shown that at 0 K the non-perovskite structure of the CsSnI₃ compound (δ-CsSnI₃) is the most stable (followed by γ-CsSnI₃), and the tetragonal phase (β) is quite unstable, having the highest energy among the perovskite phases. It was revealed that at temperatures above 450 K the tetragonal phase becomes stable, and when the temperature drops, it transforms into the cubic phase (α-CsSnI₃). The phase transition between the β and γ phase of perovskite occurs in the range of 300-320 K, and at 320 K a black-yellow transformation of CsSnI₃ occurs in which the cubic phase (black perovskite) undergoes a phase transition to a non-perovskite conformation (yellow phase). The presence of temperature phase transitions between two orthorhombic phases of CsSnI₃ at 360 K was discovered, although direct transitions of the α⟷γ and γ⟷δ types have not yet been reported in any experiment, except for γ→δ transitions under the influence of moisture. Based on well-relaxed structures (from the SCAN calculations), the band gap widths for four CsSnI₃ phases were calculated and compared with experimental measurements. Electronic properties and Fermi level shifts as a result of phase transformations of CsSnI₃ were assessed using the HSE06 functional and machine learning prediction. The values of the complex dielectric constant and the refractive index of all phases of the CsSnI₃ were determined.

The aim of the paper is to analyze the experimental results of the influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1000 °C and strain rates range 0.0018 - 0.1 s^-1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analyzed. Due to the dynamic recrystallization phenomenon present during the hot tensile tests, an increase in the flow stress is observed at the beginning of the deformation, after which it decreases until the fracture. By increasing the deformation temperature from 700 °C to 1000 °C, the tensile stress decreases significantly for all strain rates. The increase in the strain rate leads to the increase in the tensile stress. In compression tests by increasing the strain rate, the true strain is slightly increasing, but this depends on the temperature. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analyzed. Analysis by scanning electron microscopy showed the ductile behavior of the material. The degree of damage of the material caused by the presence of cavities increases by increasing the deformation temperature. For all the presented deformation conditions, the presence of the fracture through the ductile fracture mechanism was produced by the localized of necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behavior of 42CrMo4 steel can be improved.

The contemporary landscape of eHealth is characterized by major concerns related to electronic medical records (EMRs). In an EMR, critical patient health information gets its own repository, which is the core of the eHealth system. Notably, the EMR not only retrieves health information generated in ambulatory clinical settings but also includes court-generated records. These overlapping records assume the role of a foundational data source for a comprehensive electronic health record (EHR). This scholarly review sheds light on recent trends in medical records and associated challenges, while at the same time providing insights into Saudi Arabia’s targeted approaches to healthcare delivery. Additionally, the talk expands to include a description of blockchain technology and its underlying conceptual framework. This demonstration positions blockchain technology as a promising approach that requires consideration for future use in the healthcare system.

A systematic and comprehensive review of critical applications of Blockchain Technol-ogy with Differential Privacy integration lies within the privacy and security enhancement. This paper aims to highlight the research issues in the e-health domain (e.g., Electronic Medical Rec-ords) and to review the current research directions in Differential Privacy integration with Blockchain Technology.(1) Background: The current state of the art in the e-health domain is identified as follows: (a) healthcare information poses a high level of security and privacy concerns due to its sensitivity; (b) due to vulnerabilities surrounding the healthcare system, a data breach is common and presents a risk for attacks by an adversary; and (c) the current privacy and security apparatus needs further fortification. (2) Methods: The methodology uses a systematic literature review (SLR) to identify and select relevant research papers and academic journals in DP and BT. (3) Results: The results are categorized into: e-Health Record Privacy, Real-Time Health Data, and Health Survey Data Protection to identify inherent issues with Differential Privacy integra-tion with Blockchain and technical challenges.(4) Conclusion: This review thoroughly surveyed and summarized Differential Privacy mechanisms in EMR privacy, real-time health data, and health survey data protection while highlighting challenges.

Taiwan’s Chi Mei Medical Center has a vision of becoming a sustainable organization. They found they violated the sustainable development goal (SDG) 13 (“Climate Action”) since its workflows consume excessive tangible resources and waste much operation time. To fulfill the vision, the Chi Mei Medical Center first introduced electronic invoicing. Implementing this electronic invoicing included adopting cloud E-invoice data and creating a software robot for auditing them. This study presents this software robot and its contributions. The software robot replaces an internal auditor to log into Taiwan’s E-invoice platform, download cloud E-invoice data, and detect the inconsistency between these cloud and on-premise data. Internal auditors of the Chi Mei Medical Center only needed to confirm the detection results. They welcome this software robot since it significantly reduces their work burdens. They approved more software robots for assisting other workflows. Besides, the Chi Mei Medical Center earned profits after eliminating paper invoices. This elimination helped release less carbon. This study concludes that chasing a sustainable organization is unnecessarily equivalent to the requirement of more costs. A software robot represents the last puzzle for constructing a paperless workflow since it can resolve the resistance of existing workers to a new workflow.

To study and monitor the adverse health consequences from using electronic cigarettes, a user’s puff topography, which are quantification parameters of the user’s vaping habits, plays a central role. In this work, we introduce a topography sensor to measure the mass of total particulate matter generated in every puff and to estimate the nicotine yield. The sensor is compact and low-cost, and is integrated into the electronic cigarette device to promptly and conveniently monitor the user’s daily puff topography. The topography sensor is comprised of a photometric sensor and a pressure sensor. The photometric sensor measures the mass concentration of the aerosol, based on scattering of near-infrared light from airborne particles, while the pressure sensor measures the flow rate. The topography sensor was experimented under various conditions with a wide range of atomizer power, puff duration, and inhalation pressure. The sensor’s accuracy was validated by comparing the sensor’s readings with reference measurements, and the results matched closely with the trends reported by existing studies on electronic cigarettes. An example application of tracking a user’s puff topography was also demonstrated. Our topography sensor holds great promise in mitigating health risks of vaping, and in promoting quality control of electronic cigarette products.

Background: Although electronic health records (EHR) provide useful insights into disease patterns and patient treatment optimisation, their reliance on unstructured data presents a difficulty. Because of their narrative structure, echocardiography reports, which provide extensive pathology information for cardiovascular patients, are particularly challenging to extract and analyse. Although natural language processing (NLP) has been utilised successfully in a variety of medical fields, it is not commonly used in echocardiography analysis. Objectives: To develop an NLP-based approach for extracting and categorizing data from echocardiography reports by accurately converting continuous (e.g. LVOT VTI, AV VTI, and TR Vmax) and discrete (e.g. Regurgitation severity) outcomes in semi-structured narrative format into structured and categorized format, allowing for future research or clinical use. Methods: 135,062 Trans-Thoracic Echocardiogram (TTE) reports were derived from 146967 baseline Echocardiogram reports and split into three cohorts: Training and Validation (n = 1075), Test Dataset (n = 98) and Application Dataset (n = 133,889). The NLP system was developed and iteratively refined using medical expert knowledge. The system was used to curate a moderate-fidelity database from extractions of 133,889 reports. A hold-out validation set of 98 reports was blindly annotated and extracted by two clinicians for comparison with the NLP extraction. Agreement, discrimination, accuracy and calibration of outcome measure extractions were evaluated. Results: Continuous outcomes including LVOT VTI, AV VTI, and TR Vmax exhibited perfect inter-rater reliability using intra-class correlation scores (ICC=1.00, P< 0.05) alongside high R2 values, demonstrating an ideal alignment between the NLP system and clinicians. Good level (ICC =0.75-0.9, P<0.05) of inter-rater reliability were observed for outcomes such as LVOT Diam, Lateral MAPSE, Peak E Velocity, Lateral E' Velocity, PV Vmax, Sinuses of Valsalva, and Ascending Aorta diameters. Furthermore, the accuracy rate for discrete outcome measures was 91.38% in the confusion matrix analysis, indicating effective performance. Conclusions: The NLP-based technique yielded good results when it came to extracting and categorising data from echocardiography reports. The system demonstrated a high degree of agreement and concordance with clinician extractions. This study contributes to the effective use of semi-structured data by providing a useful tool for converting semi-structured text to structured echo report that can be used for data management. Additional validation and implementation in healthcare settings can improve data availability and support research and clinical decision-making.

Two-dimensional (2D) bismuth oxyhalides (BiOX) have attracted much attention as potential optoelectronic materials. Expecting for their application diversity, we herewith systematically investigate the tunable properties of 2D BiOX by using first principles calculations. Their electronic and optical properties can be modulated by changing the number of monolayers, applying strain, and/or varying the halogen composition. The bandgap shrinks monotonically and approaches the bulk value, the optical absorption coefficient increases, and the absorption spectrum redshifts, as the layer number of 2D BiOX increases. Carrier transport property can be improved by applying tensile strain, and the ability of photocatalytic hydrogen evolution can be obtained by applying compressive strain. General strain engineering will be effective in linearly tune the bandgap of BiOX in a wide strain range. Strain together with halogen composition variation can tune the optical absorption spectrum to be on demand in the range from visible to ultraviolet. It suggests that that 2D BiOX materials have potential serving as tunable novel photodetectors, can be used to improve clean energy techniques, and are prospective in the field of flexible optoelectronics.

Changes in the atomic and electronic structure of silicon carbide 3C-SiC (β-SiC), resulting from lead adsorption, have been studied within the density functional theory. The tests were conducted for three representative surfaces with varying degrees of lead coverage. Results indicate that chemisorption occurs, with the strongest binding, found on the hexagonal surface (111) in interaction with three dangling bonds. The adsorption energy rises with increasing coverage, especially as the surface approaches saturation. Analysis of the data was focused on parameters important for corrosion processes such as bond distances, binding energies, Bader charges and charge density difference.

The very slow anodic oxygen evolution reaction (OER) greatly limits the development of large-scale hydrogen production via water electrolysis. By replacing OER with easier urea oxidation reaction (UOR), developing a HER/UOR coupling electrolysis system for hydrogen production can significantly save energy and costs. Al doped cobalt ferrocyanide (Al-Co2Fe(CN)6) nanocube array was in-situ grown on nickel foam (Al-Co2Fe(CN)6/NF). Due to the unique nanocube array structure and regulated electronic structure of Al-Co2Fe(CN)6, the as-prepared Al-Co2Fe(CN)6/NF electrode exhibited outstanding catalytic activities and long-term stability to both UOR and HER. The Al-Co2Fe(CN)6/NF electrode needed potentials of 0.169 V and 1.118 V (vs. reversible hydrogen electrode) to drive 10 mA cm−2 for HER and UOR, respectively, in alkaline condition. Applying the Al-Co2Fe(CN)6/NF to a whole urea electrolysis system, 10 mA cm−2 was achieved at a cell voltage of 1.357 V, which saved 60% electricity energy comparing to that of tranditional water splitting. Density functional theory calculations demonstrated that the boosted UOR activity comes from Co sites with Al doped electronic environments. This promoted and balanced the adsorption/desorption of main intermediates in UOR process. This work indicates that Co based materials as efficient catalysts have great prospects for application in urea electrolysis systems, and are expected to achieve low-cost and energy-saving H2 production.

A full potential all-electron density functional method within generalized gradient approximation is used to investigate the electronic, elastic and transport properties of cubic copper sulphide and copper selenide. The electronic structure suggests metallic behavior with a zero energy band gap for both materials. Elastic property calculations suggest a stiff material with the bulk to shear modulus ratio of 0.35 and 0.44 for Cu2S and Cu2Se respectively. The transport properties were estimated using the Boltzmann transport approach. Seebeck coefficient, electrical conductivity, thermal conductivity, and power factor all suggest a potential p-type conductivity for Cu2S and n-type conductivity for Cu2Se.

The Internet of Things (IoT) was born from the fusion of virtual and physical space and became the initiator of many scientific fields. Economic sustainability is the key to further development and progress. Today, the need for electronic commerce has become an economic priority in the transition period between Industry 4.0 and Industry 5.0. Unlike mass production in Industry 4.0, customized production in Industry 5.0 should reach its true potential in vertically organized management and decision-making systems. The authors focused their research on e-commerce based on the three-level vertical IoT environment and the edge, fog, and cloud computing. The paper presents hands-on machine learning (ML) algorithms to facilitate the transition from a flat to a vertical e-commerce concept. The authors also propose practical ML algorithms for a few e-commerce types: consumer-consumer relationships and consumer-company-consumer relationships. These algorithms are mainly composed of convolution neural networks (CNN), natural language understanding (NLU) and sequential pattern mining (SPM), reinforcement learning (RL for agent training), algorithms for clicking on the item prediction, consumer behavior learning, etc. All presented concepts, algorithms, and models are described in detail.

The idealized rhombohedral unit cell of boron carbide is formed by a 12-atom icosahedron and a 3-atom linear chain. Phase transitions are second order and caused by the exchange of B and C sites or by vacancies in the structure. Nevertheless, the impact of such minimal structural changes on the properties can be significant. As the X-ray scattering cross sections of B and C atoms are very similar, the capability of X-ray fine structure investigation is restricted. Phonon spectroscopy helps closing this gap. Phase transitions known to date have been identified due to significant changes of properties: (1) The phase transition near the chemical composition B8C by clear change of the electronic structure; (2) The endothermic temperature-dependent phase transition at 712 K by the according change of specific heat; (3) The high-pressure phase transition at 33.2 GPa by the drastic change of optical appearance from opacity to transparency. These phase transitions affect IR- and Raman-active phonons and other solid-state properties. The phase transitions at B~8C and 712 K mean that a well-defined distorted structure is converted into another one each. In the high-pressure phase transition, an apparently well-defined distorted structure changes into a highly ordered one. In all these cases, the distribution of polar C atoms in the icosahedra plays a crucial role.

Ants have a very sophisticated olfactory system; their communication is based on the interpretation of chemical trails known as semiochemicals. The escamolera ant (Liometopum apiculatum), has behaviors and physiological responses is induced by semiochemicals, without however, these have not been studied. Using an electronic nose analysis (e-nose) and chromatographic techniques, semiochemicals of L. apiculatum in nests, foraging trails and dissected the gasters were evaluated. Data were analyzed with multivariate statistics and a logistic regression model based on predictors (ant counts) and the semiochemicals identified in pre-season (PRE), season (TEM) and post-season (POS) of larval collecting. From the general pattern of volatiles with a natural separation in POS and a partial distribution between PRE and TEM 32 semiochemicals were identified inside the nests, those who can induce the behavioral responses of trail-following, alarm, aggression, and nestmate recognition. Trail counts indicated that ant traffic was higher in POS and that the presence of certain semiochemicals (response variable) have good fit in the model regression. These findings are intended to provide useful information and support decision-making for the conservation and sustainable use of L. apiculatum in central Mexico.

TmMgB5O10 spontaneous crystals were synthesized via flux-growth technique from a K2Mo3O10-based solvent. The crystal structure of the compound was solved and refined within the space group P21/n. The first principles calculations of the electronic structure reveal that TmMg-pentaborate is an insulator with an indirect energy band gap of approximately 6.37 eV. Differential scanning calorimetry measurements and powder X-ray diffraction studies of heat-treated solids show that TmMgB5O10 is an incongruent melting compound. A characteristic band of Tm3+ cation corresponding to the 3H6 → 1D2 transition is observed in the photoluminescence excitation spectra of TmMg-borate. The as-obtained crystals exhibit intense blue emission with the emission peaks centered at 455, 479, 667 and 753 nm. The most intensive band corresponds to the 1D2 3F4 transition.

In a previous paper, we solved the partial differential equation of Mullins problem in the case of the evaporation-condensation in electronic devices and gave an exact solution relative to the geometric profile of the grain boundary grooving when materials are submitted to thermal and mechanical solicitation and fatigue effect. In this new research, new modelling of the grain groove profile was proposed and new analytical expressions of the groove profile, the derivative and the groove depth were obtained in the case of diffusion in thin polycrystalline films by the resolution of the fourth differential equation formulated by Mullins that supposed 〖y'〗^2≪1. The obtained analytical solution gave more accurate information on the geometric characteristics of the groove that were necessary to study the depth and the width of the groove. These new findings will open a new way to study with more accuracy the problem of the evaporation-condensation combined to the diffusion phenomenon on the material surfaces with the help of the analytical solutions.

The time-resolved CIDNP method can provide information about degenerate exchange reactions (DEE) involving short-lived radicals. In the temperature range from 8 to 65°C, the DEE reactions of the guanosine-5’-monophosphate anion GMP(-H)- with the neutral radical GMP(-H)•, of the N-acetyl tyrosine anion NacTyrO- with a neutral radical NacTyrO• and of the tyrosine anion TyrO- with a neutral radical TyrO• were studied. In all the studied cases, the radicals were formed in the reaction of quenching triplet 2,2’-dipyridyl. The reorganization energies were obtained from Arrhenius plots. The rate constant of the reductive electron-transfer reaction in pair GMP(-H)•/TyrO- was determined at T = 25°C. Rate constants of GMP(-H)• radical reduction reactions with TyrO- and NacTyrO- anions calculated by the Marcus cross relation differ from the experimental ones by two orders of magnitude. The rate constants of several other electron transfer reactions involving GMP(-H)-/•, NacTyrO-/•, and TyrO-/• pairs calculated by cross relation agree well with the experimental values. The rate of nuclear paramagnetic relaxation was found for the 3,5 and β-protons TyrO• and NacTyrO•, the 8-proton GMP(-H)• the 3,4-protons DPH• at each temperature. In all cases, the dependences of the rate of nuclear paramagnetic relaxation on temperature are described by the Arrhenius dependence.

The Covid-19 pandemic has forced the transfer of local government public ser-vices to the virtual world. Remote handling of matters in government offices has be-come the norm rather than the exception. The 2016 EU directive on public sector web-sites and mobile applications and the 2019 European Digital Accessibility Act made it mandatory that these services be provided electronically and accessible to people with disabilities. The purpose of the study conducted by the authors was to determine whether the Covid-19 pandemic resulted in the implementation of European solutions in the Polish legal order and whether this implementation resulted in the actual adap-tation of digital activities of local government units (LGUs) to the needs of people with disabilities. The research was conducted in Q4 2022 in two trial formats: 1. In the form of a survey (about 250 LGUs), which covered compliance with for-mal requirements, the level of readiness of the officials to create digitally accessible documents and content, and organizational readiness of the offices. 2. In the form of an analysis of the source code of the websites of 66 Polish cities with county rights - due to the availability of results of the same sample from 2015. The completed research showed that the LGUs in Poland: 1. met the formal and organizational requirements for digital accessibility, 2. did not make the necessary efforts to prepare employees to create digitally ac-cessible documents and content, 3. the surveyed websites had inferior source code in terms of meeting the WCAG standard in 2022 than in 2015. It seems reasonable to conclude that the Covid-19 pandemic had a formal, rather than real, impact on the digital accessibility of services provided by Polish LGUs.

The analysis of the 2002 Prestige tanker accident showed how public misinformation can worsen marine pollution incidents, rendering their management suboptimal as these evolve, raising thus the issue of appropriately informing and educating coastal and island populations at risk. Two decades later, developments in electronic platforms, Geographic Information Systems (GIS), in Automatic Identification System (AIS) for ship signal transmission, and in social media, provide a set of means for public monitoring of such incidents, creating the possibility to antagonize effec-tively erroneous, or malevolent information which can hinder efficient actions for containing ma-rine pollution risks even without active training of populations concerned. The authors, in the framework of development of the Marine Coastal Observatory and Risk Management project “AEGIS+”, have developed E-S.A.V.E., an online platform which: a) meets the needs of different users as revealed by a survey run across groups of them, b) uses a suitable Geographic Infor-mation Systems (GIS) environment, c) cooperates with public authorities, for the reliable update of automated systems, and d) employs an artificial intelligence (AI) supported tool for social me-dia monitoring; the platform also provides educational and information national and interna-tional resources on marine environmental protection and sustainable maritime logistics.

Ethylene is an ideal CO2 product in an electrocatalytic CO2 reduction reaction (CO2RR), which has high economic value. In this paper, Al–doped octahedral Cu2O (Al–Cu2O) catalyst was synthesized by a simple wet chemical method. The selectivity of CO2RR products was improved by doping Al onto the surface of octahedral Cu2O by regulating the Al content. The Al–Cu2O was used as an efficient electrocatalyst for CO2RR with selective ethylene production. The Al–Cu2O exhibited a high Faradic efficiency (FEC2H4) of 44.9% at -1.23 V (vs. RHE) in CO2 saturated 0.1 M KHCO3 electrolyte. Charge transferring from Al atom to Cu atom take place after Al doping in Cu2O, thereby optimizing the electronic structure, which facilitates CO2RR to ethylene production. The DFT calculation showed that the Al–Cu2O catalyst can effectively reduce the adsorption energy of the *CHCOH intermediate and promote the mass transfer of charges, thus improving the FEC2H4. After Al doping into Cu2O, the center of d orbitals shift positively, which makes the d–band closer to the Fermi level. Furthermore, the density of electronic states increases, which was conducted to the interaction between Cu atoms and intermediates, thus accelerating the electrochemical CO2 reduction process. This work proved that the metal doping strategy can effectively improve the catalytic properties of Cu2O, thus providing a useful way for CO2 cycling and green production of C2H4.

— Printing electronics incorporates several significant technologies, such as semiconductor devices produced by various printing techniques on flexible substrates. With growing interest in printed electronic devices, new technologies have been developed to make novel devices with inexpensive and large-area printing techniques. This review article focuses on the most recent developments in printed photonic devices. Photonics and optoelectronic systems may now be built utilizing materials with specific optical properties and 3D designs achieved through additive printing. Optical and architected materials that can be printed in their entirety are among the most promising future research topics, as are platforms for multi-material processing and printing technologies that can print enormous volumes at high resolution while also maintaining high throughput. Significant advances in innovative printable materials create new opportunities for functional devices to act efficiently, such as wearable sensors, integrated optoelectronics, and consumer electronics. This article provides an overview of printable materials, printing methods, and uses of printed electronic devices.

The process of building microgrids on top of existing passive distribution networks warrants a multi-criteria analysis. Besides the calculation of investment outlays needed for the modernization of distribution networks, such an analysis covers an assessment of the technological and economic effects of building microgrids. The resulting effects depend on the topology and configuration of distribution networks, specific microgrid features, the choice of current type for the entire microgrid or its individual parts, the ways of connecting distributed energy resources (DER), the availability and condition of information and communications technology (ICT) infrastructure, and other factors. Complete input data allow one to design an optimal microgrid configuration, but the main technological and economic effects are determined by the algorithms of operation and the parameters setting of the automatic control system (ACS) and the protection system. Known approaches to designing microgrids focus on addressing basic tasks while minimizing investment required for their implementation. The above is fully justified when constructing new microgrids, but building microgrids on top of existing distribution networks, given the uniqueness of their topology and configuration, does not allow the use of standardized solutions. The development of approaches to the design of microgrids under such constraints, with minimized investment for the modernization of existing distribution networks, is an urgent task. The use of different types of current for microgrid segments determines the choice of particular ACS and protection system, which depends on the availability of information and communications technology infrastructure. This article contributes a review of approaches to designing AC and AC-DC microgrids to maximize their technological and economic effects. We review techniques for analyzing existing distribution networks aimed at choosing the type of current for the entire microgrid or its individual parts, the optimal connection points of microgrids to distribution networks, the mix and capacity of DERs, with such choices informed by the condition of switching devices and information and communications technology infrastructure. The article presents the results of the analysis of approaches to choosing the optimal configuration of microgrids, microgrid ACS and protection system, with an evaluation of the technological and economic effects subject to minimization of investment for the modernization of existing distribution networks.

The exponential growth in the consumption of electronics, in combination with the reduction in their useful life, leads to a significant increase in the volume of electronic material discarded. Printed Circuit Boards (PCBs) are modules composed of ceramic, polymer and metallic materials of high economic value and with a great potential for damage to biotic and anthropic environments when inadequately discarded. The aims of this work was to study the main environmental impacts and the efficiency of mechanical operations in the electronic waste recycling process in optimizing the concentration of metallic copper. For this, the samples obtained were characterized according to their morphology and chemical composition, and subjected to physical and mechanical treatments: dismantling, grinding, separation by granulometry, density and magnetic property. The environment impacts were estimated by the Life Cycle Assessment of the pre-treatment processes, associated with copper extraction operations in WPCBs. According to the results obtained, it is possible to infer that the NM +1mm Concentrated product presents in its metallic composition around 78% of copper, which contributes to the efficiency of the hydrometallurgical extraction processes. It is noteworthy that the Concentrated class represents about 14% of copper (wt) taking into account the amount of 3.789 kg of PCB waste input material. The potential for reinsertion of the dust in the material recovery process is highlighted, given that the chemical composition of this particulate has a significant presence of metals. In general, it was found that due to the higher concentration (wt %) of the sample being allocated in the range of - 0.15mm + 0.05mm, the elements Fe (18.30%), Si (10.73%), Ca (9.21%) and Cu (8.89%) stand out regarding the participation of the elemental composition of this fraction and also regarding the general composition of the sample. Furthermore, the generation of dust during the fragmentation process, can be associated with occupational respiratory diseases when not managed. About the Life Cycle Assessment, in seven of the nine categories evaluated, crushing and screening activities accounted for more than 90% of the recorded impact values. In general, it is estimated that in the pre-treatment phase be generated 15.4 kg CO2 eq.

The study aimed to identify clinical pharmacology patterns of prescribed and taken medications in older cardiovascular patients using electronic health records (EHRs) (n = 704) (2019–2022). Medscape Drug Interaction Checker was used to identify pairwise drug-drug interactions (DDIs). Prevalence rates of DDIs were 73.5% and 68.5% among taken and prescribed drugs, respectively. However, total number of DDIs was significantly higher among prescribed medications compared with the list of taken drugs (p < 0.05). Serious DDIs comprised 16% and 7% of all DDIs among prescribed and taken medications, correspondingly (p < 0.05). Median DDI numbers between prescribed versus taken medications were Me = 2, IQR 0-7 and Me = 3, IQR 0-7 per record, respectively. Prevalence of polypharmacy was significantly higher among prescribed medications compared with taken medications (p < 0.05). Women were taking significantly more drugs and had higher rates of polypharmacy and DDIs (p < 0.05). No sex-related differences were observed in the list of prescribed medications. ICD code U07.1 (COVID-19, virus identified) was associated with the highest median DDI number per record. Further research is warranted to improve EHR structure, patient engagement in reporting adverse drug reactions, and genetic profiling of patients to avoid potentially serious DDIs.

This paper presents a method of fusion of identification (attribute) information provided by two types of sensors: combined primary and secondary (IFF) surveillance radars and ESM (Electronic Support Measures). In the first section, the basic taxonomy of attribute identification is adopted in accordance with the standards of STANAG 1241 ed. 5 and STANAG 1241 ed. 6 (draft). These standards provide the following basic values of the attribute identifications: FRIEND, HOSTILE, NEUTRAL, UNKNOWN and additional values: ASSUMED FRIEND and SUSPECT. The basis of theoretical considerations is Dezert-Smarandache theory (DSmT) of inference. The paper presents and practically uses for combining identification information from different ESM sensors and radars six information fusion rules proposed by DSmT - the Proportional Conflict Redistribution rules (PCR1, PCR2, PCR3, PCR4, PCR5 and PCR6). In the paper, rules of determining attribute information by ESM sensor equipped with the data base of radar emitters are presented. It was proposed that each signal vector sent by the ESM sensor contained an extension specifying a randomized identification declaration (hypothesis) - basic belief assignment (BBA). The paper also presents a model for determining the basic belief assignment for a combined primary and secondary radar. Results of the PCR rules of sensor information combining for different scenarios of radio-electronic situation (deterministic and Monte Carlo) are presented in the final part of the paper. They confirm the legitimacy of the use of Dezert-Smarandache theory into information fusion for primary radars, secondary radars and ESM sensors.

In this article, an efficient die bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and the heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, FE-simulation methods were applied in order to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests in order to qualify the inductive bonding technology. The results presented in this paper demonstrate, that induction heating has high potential for cost effective production in the field of die-attach and can drastically increase the output in power electronics production.

Objective: To quantitatively analyze the production of Doctoral Theses on health issues related to gender in Spain. Method: Quantitative synthesis of the productivity indicators of the Doctoral Theses de-fended in Spanish Universities between 1976 and 2022, obtained from the Spanish TESEO data-base. Descriptive analysis, materialized in tables and graphs, and time series model, based on the Holt-Winters model methodology. Results: 18.75% of the defended Doctoral Theses represents the scientific production of the Universities. Madrid is where the greatest number defend themselves with 37.5%. One in three authors are graduates in medicine. The theme of the Theses is gender violence in 25.0%, the authors are women in 87.5%, 44.0% of women direct theses. The scientific production of directors according to the H Index is very uneven, since one person has an index of 76 and another of 1. The temporal sequence of production is erratic, since in some years no Doctoral Theses are defended, but in 2017 were three. Conclusions: Spanish research in clinical Doctoral Theses on gender is scarce. It would be desirable to develop doctoral programs that promote the generation of theses in health that have gender differences in health care as their central point.

A number of sustainable and environmental issues are caused by consumer's behavior. Consumers' consumption pattern plays an increasingly important role in environmental conservation and adopting to a more sustainable community. This study used planned behavior theory and structural equation model to quantifies individual purchasing behavior of electronic vehicles based on perceived health risk cased by air pollution in Kunming, China. The findings showed that (1)for residents in Kunming, the perceived air pollution risk, the willingness to purchase new energy vehicles, and actual purchase behavior are low; (2) perception of health risks has a significant positive impact on purchase willingness, behavioral attitude and subjective norms play a significant positive mediating role between perception of health risks and purchase willingness, and perception of behavioral control plays a significant negative role, purchase willingness has significant positive impact on purchase behavior, the direct effect of perceived behavioral control on purchase behavior is insignificant; (3) for highly educated groups, risk controllability has a significant impact on the perception of health risk, subjective norms and behavioral attitude have significant impacts on purchase willingness, while for low-income gourp, risk controllability has significant impacts on the perception of health risk.

In recent years, two-dimensional (2D) materials have attracted significant attention due to their distinctive properties, including exceptional mechanical flexibility and tunable electronic properties. Via the first-principles calculation, we investigate the effect of strain on the electronic properties of monolayer SnP2S6 and GeP2S6. We find that monolayer SnP2S6 is an indirect band gap semiconductor, while monolayer GeP2S6 is a direct band gap semiconductor. Notably, under uniform biaxial strains, SnP2S6 undergoes an indirect-to-direct band gap transition at 4.0% biaxial compressive strains, while GeP2S6 exhibits a direct-to-indirect transition at 2.0% biaxial tensile strain. The changes of the conduction band edge can be attributed to the high-symmetry point Γ being more sensitive to strain than K. Thus, the relocation of the conduction-band and valence-band edges in monolayer SnP2S6 and GeP2S6 induces a direct-to-indirect and indirect-to-direct band-gap transition respectively. Consequently, the strain is an effective band engineering scheme which is crucial for the design and development of next-generation nanoelectronic and optoelectronic devices.

Companion animals are increasingly being recognized as important contributors to the spreading of antimicrobial resistant bacteria. The present work aimed to measure the antimicrobial drug prescribing in dogs and cats in the Campania region, Italy by analyzing the Veterinary Electronic Prescriptions (VEPs) between 2019 and 2020. The medical records associated with antimicrobial drug prescription were collected considering the drug delivery (systemic or local) and the rationale for the treatment chosen. In the period under investigation, 166879 drugs were prescribed of which 129116 (73.37 %) were antimicrobial. A total of 83965 (65.03 %) antibiotics were prescribed to dogs, 40477 (31.35 %) to cats, and 4674 (3.62 %) to other companion animals. In dogs the 90.48 % of VEPs prescribed for systemic treatment included an antimicrobial Critically Important or Highly Important or Important for human medicine (WHO, 2018). The most widely commonly prescribed class were fluoroquinolones. The main prescribed antimicrobials were the metronidazole-spiramycin (29.71%), amoxicillin-clavulanic (19.58%), enrofloxacin and cephalexin in dogs (16.52 %) and enrofloxacin (22.64%) and amoxicillin-clavulanic acid (21.37 %) in cats. Based on the results the wide use of broad-spectrum or second-line antibiotics is emerged together with the use of the critically important antimicrobials for human medicine.

This study evaluated the effectiveness of an electronic system for managing drug-sensitive pulmonary tuberculosis patients in the Kyrgyz Republic. This was a cohort study using programmatic data. The study included patients registered on the paper-based system in 2019 and the electronic system between June 2021 and May 2022. Data was taken from 302 individuals from the electronic system for completeness and concordance in comparison with the paper-based system. The study showed that for most variables the completeness and concordance was 85.3%-93.0% and was lowest for non-mandatory fields such as medication side effects (26.8% vs 13.6%). No significant difference was observed in time taken from symptom onset to diagnosis and treatment initiation between the two systems. However, the electronic system had a significantly higher percentage of patients who initiated treatment on the same day of diagnosis (80.3% vs. 57.1%). The proportion with successful outcomes was similar in both groups, but the electronic system had a significantly lower proportion of patients with outcomes that were not evaluated or recorded (4.8% vs. 14.3%, p &lt; 0.001). The study highlights the potential advantages of implementing an electronic TB register system for improving records. We advocate for similar studies in other regions in Kyrgyz Republic.

In this article, we delve into the intricate behavior of electronic mechanisms underlying NMR magnetic shieldings, σ, in molecules containing heavy atoms such as cadmium, platinum, and mercury. Specifically, we explore PtXn^{−2} (X = F, Cl, Br, I; n = 4, 6) and XCl2 Te2 Y2 H6 (X = Cd, Hg; Y = N, P) molecular systems. It is known that the leading electronic mechanisms responsible for the relativistic effects on σ are well characterized by the linear response with elimination of small components model (LRESC). In this study, we present results obtained from the innovative LRESC-Loc model, which offers the same outcomes as the LRESC model but employs localized molecular orbitals (LMOs) instead of canonical MOs. These LMOs provide a chemist’s representation of atomic core, lone pairs, and bonds. The whole set of electronic mechanisms responsible of the relativistic effects can be expressed in terms of both non-ligand-dependent and ligand-dependent contributions. We elucidate the electronic origins of trends and behaviors exhibited by these di- verse mechanisms in the aforementioned molecular systems. In PtX4^{−2} molecules, the predominant relativistic mechanism is the well-established one-body spin-orbit (σ^SO(1) ) mechanism, while the paramagnetic mass-velocity (σ^Mv ) and Darwin (σ^Dw ) contributing mechanisms also demand con- sideration. However, in PtX6−2 molecules, the σ Mv+ Dw contribution surpasses that of the SO(1) mechanism, thus influencing the overall ligand-dependent contributions. As for complexes con- taining Cd and Hg, the ligand-dependent contributions exhibit similar magnitudes when nitrogen is substituted with phosphorus. The only discrepancy arises from the σ^SO(1) contribution, which changes sign between the two molecules due to the contribution of bond orbitals between the metal and tellurium atoms.

(1) Objectives. Patients with heart failure (HF) who experience hospitalizations for worsening HF (HFH) are at high risk of subsequent events. We aimed to evaluate the impact of an outpatient care management program that includes a clinician-to-clinician e-consultation using an integrated electronic medical record in a healthcare area with a widely dispersed population on delay time in care, hospital admissions, and mortality in a high-risk group of patients with HF and previous episodes of HFH. (2) Methods. We selected 6,444 HF patients who visited the cardiology service at least once between 2010 and 2021. Of these, 4,851 were attended in e-consult, and 2,008 in one-time in-person consultations. In 2,230 HF patients, there was documentation of a previous episode of HFH. Using an interrupted time series regression model, we analysed the impact of incorporating e-consult into the health care model in the group of patients with HFH and evaluated the elapsed time to cardiology care, heart failure (HF), cardiovascular (CV), and all-cause hospital admissions and mortality, calculating the incidence relative risk (iRR). (3) Results. In the group of patients with previous HF hospitalizations, the introduction of e-consult substantially decreased waiting times to cardiology care. The time elapsed to care after e-consult implementation was significantly reduced compared with the previous in-person period (8.6 [8.7] vs 55.4 [79.9] days, p&lt;0.001). In that group of patients, after e-consult implantation, hospital admissions for HF were reduced (iRR [CI95%]: 0,837 [0,840-0,833]), 0,900 [0,862-0,949] for CV and 0,699 [0,678-0,726] for all-cause hospitalizations. There was also lower mortality (iRR [CI95%]: 0.715 [0.657-0.798] due to HF, 0,737 [0.764-0.706] for CV and 0,687 [0.652-0,718] for all-cause). The improved outcomes after e-consultation implementation were significantly higher in the group of patients with previous HFH and were independent of the patient’s clinical characteristics managed during the in-person or e-consultation periods. (4) Conclusions. In HF patients with previous HFH, an outpatient care program that includes an e-consult significantly reduced waiting times to cardiology care and was safe, with a lower rate of hospital admissions and mortality in the first year.

Physics of high-Tc superconducting cuprates is obscured by the effect of strong electronic correlations. One way to overcome the problem is to seek for an exact solution at least within the small cluster and expand it to the whole crystal. Such an approach is in the heart of the cluster perturbation theory (CPT). Here we develop CPT for the dynamic charge and spin susceptibilities (spin-CPT), within which the correlation effects are explicitly taken into account by the exact diagonalization. We apply spin-CPT to the effective two-band Hubbard model for the cuprates obtained from the three-band Emery model and calculate one- and two-particle correlation functions, namely, spectral function and spin and charge susceptibilities. Doping dependence of the spin susceptibility was studied within spin-CPT and CPT-RPA that is the CPT generalization of the random phase approximation (RPA). Both methods produce the low energy response at four incommensurate wave vectors in qualitative agreement to the results of the inelastic neutron scattering on overdoped cuprates.

Semantic interoperability facilitates exchange and access of health data that is being documented in EHRs with various semantic features. In the EU, the regulation proposal of European health data space requires development of semantic interoperability. To achieve a fully integrated EHDS ecosystem leveraging the value of health data, stakeholders need to overcome challenges of implementing common standards and other semantic interoperability features. We aimed to research what scientific evidence is available on developing semantic interoperability. Our research questions focused specifically on key features and approaches for semantic interoperability and on possible benefits of these choices. For that purpose, we performed a systematic literature review by defining our study framework based on previous research. Our results consisted of 10 studies where data models, ontologies, terminologies, classifications, and standards were applied for building interoperability. Through increased access to interoperable patient information, a better quality and outcomes in care can be achieved. Better communication based on easily accessible data is facilitated between health professionals and between clinicians and the patients. When heading towards semantic harmonization as outlined in the EHDS proposal, more experiences and analyses are needed to assess how applicable the chosen solutions are for semantic interoperability of European health care data.

Innovation development in healthcare has paved the path towards the improvement in system efficiency, patient care and cost-effective healthcare services, increasing the overall efficiency of the healthcare system in a significant manner. Electronic medical record system has fostered interoperability and collaboration in healthcare departments by enabling different systems to exchange and use patient data. This trend has been accelerated dominantly by the pandemic, leading to increased use of telemedicine, referring specifically to the use of electronic communication to provide healthcare services remotely. Moreover, an increased prevalence towards the use of artificial intelligence and machine learning in healthcare has contributed effectively towards the rigorous and informed analysis of large amounts of data as well as to identify patterns or trends that may be useful for improving care delivery or identifying potential issues. A unified electronic medical record System that will generate competitive opportunities and success prospects with reference to enhanced interoperability in US healthcare departments, can contribute towards the improvement in the quality and efficiency of care by making it easier for healthcare providers to access and share patient information as well as reducing the risk of errors in effective patient care.

The extracellular matrix (ECM) is earning an increasingly relevant role in many disease states and the process of aging. Analyzing these disease states is possible with GWAS and PheWAS methodology, and through our analysis, we aimed to explore the relationships between polymorphisms in the compendium of ECM genes (i.e., matrisome genes) in various disease states. A significant contribution on the part of the ECM polymorphisms is evident in many varying types of diseases, particularly those in the core matrisome genes. Our results confirm previous links to connective tissue disorders, but also unearth new and underexplored relationships with neurological, psychiatric, and age-related disease states. Upon analysis of drug indications for gene-disease relationships, we identified numerous targets that may be repurposed for age-related pathology. The identification of ECM polymorphisms and their contribution to disease plays an integral role in future therapeutic developments, drug repurposing, precision medicine, and personalized care.

The aim of study was to investigate epidemiology aspects of magnetic resonance imaging (MRI) during COVID-19 pandemic. The study comprised depersonalized residents of Tomsk and Tomsk Region (n = 1714). Invitations to take online survey were sent to 50,000 residents by target SMS with response rate of 1.2% (n = 727, Cohort 1). Cohort 2 comprised retrospective patients (n = 987) who underwent contrast-enhanced cardiac MRI (CMR) in 2019-2022. Referrals, clinical characteristics, diagnosis, gender, age, past COVID-19, MRI study protocols, and MRI data were analyzed. 29% of respondents in cohort 1 received MRI examination within past two years; 26% of respondents considered MRI the most informative imaging modality for detecting COVID-19 pneumonia; 12% of respondents reported MRI unavailable. Proportion of CMR among MRI studies increased during COVID-19 pandemic, and maximum incidence of cardiac diseases detected by MRI was in 2021. Incidence of myocardial fibrosis increased from ~67% in 2019 to ~84% in 2022. The rate of outpatient MRI studies significantly increased in 2020, but returned to pre-pandemic level in 2021. COVID-19 pandemic increased the need for MRI and CMR. Patients with history of COVID-19 had persistent and newly occurring symptoms of myocardial damage suggesting chronic cardiac involvement requiring continuous follow-up.

COVID-19 pandemic-related pressures on primary care may have driven inappropriate continuation of antibiotic prescriptions. Yet prescribing modality (repeat/non-repeat) has not previously been investigated in a pandemic context. Using the OpenSAFELY-TPP analytics platform, we analysed repeat/non-repeat prescribing frequency in monthly patient cohorts between Jan 2020–2022. In-depth analysis was conducted on Jan 2020 (“pre-pandemic”) and Jan 2021 (“pandemic”) cohorts. Per-patient prescribing and clinical conditions were determined by searching primary care record data using clinical code lists. Repeat prescribing was defined as >=3 prescriptions in a 6 month lookback period. Associations between demographics (e.g. age, sex, geography) and repeat/non-repeat prescribing were explored using unadjusted risk ratios. Antibiotic prescribing declined from May 2020; non-repeat prescribing declined more strongly than repeat prescribing (maximum declines -26% vs -11%, respectively). In the pandemic cohort, older patients were at higher risk of prescribing (especially repeat prescribing). The most common clinical conditions for repeat prescribing were COPD comorbidity and urinary tract infection. Comorbidities were more common among repeat vs non-repeat prescribed patients. In the pandemic cohort, vs pre-pandemic, repeat and non-repeat prescribing for comorbidities generally declined less compared with shorter-term conditions (infections, including COPD exacerbation/lower respiratory tract infection). Our findings inform ongoing development of stewardship interventions in England..

Lithium-ion batteries (LIBs) have become the preferred battery system for portable electronic devices and transportation equipment because of their high specific energy, good cycling performance, low self-discharge and no memory effect. However, too low ambient temperature will seriously affect the performance of LIBs, almost cannot discharge at -40~-60 ℃. There are many factors affecting the low temperature performance of LIBs, among which the electrode material is an important factor. Thus it is urgent to develop electrode materials or modify existing materials with excellent low temperature LIBs performance. Carbon-based anode is a kind of LIBs candidate. In recent years, it has been found that the diffusion coefficient of lithium ion in graphite anode decreases more obviously at low temperature, which is one of the important bottlenecks limiting its low temperature performance. However, the structure of amorphous carbon materials is complex, amorphous carbon materials have good ionic diffusion properties, and its grain size, specific surface area, layer spacing, structural defects, surface functional groups and doping elements may have a greater impact on the low temperature performance of the material. In this work, the low temperature performance of LIBs is obtained by modifying the carbon-based material from the perspective of electronic modulation and structural engineering.

With the continuous growth of electric and electronic appliances’ usage, the waste produced with obsolete material (e-waste) has an increasing environmental impact. Also, the production of such appliances bears to increased consumption of natural resources and produces a multitude of toxic and hazardous substances, which typically are not properly treated. One of the approaches that may be adopted to reduce such problems relies on the circularization of the current linear model, commonly adopted in the EEE value chain. This includes recovering eol products and reintroducing its parts, components, or raw materials into the value chain (e.g. semiconductors, circuit boards, raw metals, etc.), thus contributing to a more sustainable value chain. In this article, we present a state-of-art review that focuses on approaches and solutions for the EEE value chain traceability, and analyses the technologies that may be beneficial for promoting and implementing the CE model in this value chain.

Technological innovations and the expansion of Internet access have produced significant changes in the configurations of organizations and, consequently, in the relationships between employees and employers. This new scenario generates the need for greater monitoring in the workplace in order to control inappropriate behavior or situations that may generate misfortunes. Two important problems faced are the dissemination of hate through networks and data leakage that can have social, psychological, and financial impacts. Thus, monitoring tools can be incorporated to assist in surveillance, and thus ensure the achievement of organizational objectives. This paper presents a workplace computer monitoring solution that integrates Spyware techniques, and text sentiment classification, along with a distributed microservices architecture, which aims to collect a range of information and generate alerts to managers regarding hate speech and vulnerabilities. Preliminary tests have been conducted to evaluate the performance of Spyware integrated with prediction models.

Objective: Determine the feasibility of utilizing longitudinal electronic dental record (EDR) data to track change over time in patient periodontal disease (PD) and to generate three patient cohorts: 1) patients whose disease did not change over time, 2) patients whose PD progressed, and 3) patients whose disease improved over time using informatics approaches. Methods: We conducted a retrospective study of 28,908 patients who received a comprehensive oral evaluation between January 1, 2009, and December 31, 2014, at the Indiana University School of Dentistry (IUSD) clinics. We developed and tested three automated computer applications to: 1) diagnose periodontitis cases from periodontal charting, 2) retrieve clinician-documented diagnoses from clinical notes, and 3) track disease change over time. We also evaluated the density of longi-tudinal EDR data for the following follow-up times: 1) none, 2) up to 5 years, 3) >5 and <=10 years, and 4) >10 and <=15 years Results: Thirty-four percent (n=9,954) of the study cohort had up to five years of follow-up visits with an average of 2.78 visits with periodontal charting information. An average of three patient visits per year that contained periodontal charts (63,552) were utilized to obtain a diagnosis, which is considered excellent. For clinician-documented diagnoses from clinical notes, 42% of patients (n=5,562) had at least two PD diagnoses to determine their disease change. In this cohort with cli-nician-documented diagnoses, 72% percent of patients (n=3,919) did not have a disease status change between their first and last visits, 669 (13%) patients' disease status progressed, and 589 (11%) patients’ disease improved. Conclusions: This study demonstrated the feasibility of utilizing longitudinal EDR data to track disease changes over 15 years during the observation study period. We found excellent longitudinal data when diagnoses generated from periodontal charting were considered (three visits per pa-tient). This information can be now utilized for studying the clinical course of periodontitis.

Generalized relativistic pseudopotentials (GRPP) of atomic cores implying the use of different potentials for atomic electronic shells with different principal quantum numbers give rise to accurate and reliable relativistic electronic structure models of atoms, molecules, clusters, and solids. These models readily incorporate the effects of Breit electron-electron interactions and one-loop quantum electrodynamics effects. Here we report the computational procedure for evaluating one-electron integrals of GRPP over contracted Gaussian functions. This procedure was implemented in a library of routines named LIBGRPP, which can be integrated into existing quantum chemistry software, thus enabling the application of various methods to solve the many-electron problem with GRPPs. Pilot applications to electronic transitions in the ThO and UO2 molecules using the new library and intermediate-Hamiltonian Fock space relativistic coupled cluster method are presented. The results clearly demonstrate that rather economical tiny-core GRPP models can exceed in accuracy relativistic all-electron models defined by Dirac-Coulomb and Dirac-Coulomb-Gaunt Hamiltonians.

Background. Cardiorespiratory fitness (CRF) is a predictor of chronic disease that is impractical to routinely measure in primary care settings. We used a new estimated cardiorespiratory fitness (eCRF) algorithm that uses information routinely documented in electronic health care records to predict abnormal blood glucose incidence. Methods: Participants were adults (17.8% female) 20-81 years old at baseline from the Aerobics Center Longitudinal Study between 1979 and 2006. eCRF was based on sex, age, body mass index, resting heart rate, resting blood pressure, and smoking status. CRF was measured by maximal treadmill testing. Cox proportional hazards regression models were established using eCRF and CRF as independent variables predicting the abnormal blood glucose incidence while adjusting for covariates. Results: Of 8,602 participants at risk at baseline, 3,580 (41.6%) developed abnormal blood glucose during an average of 4.9 years follow-up. The average eCRF of 12.03 ± 1.75 METs was equivalent to the CRF of 12.15 ± 2.40 METs within the 10% equivalence limit. In fully adjusted models, the estimated risks were the same (HRs = 0.96), eCRF (95% CIs = 0.93−0.99), and CRF (95% CI of 0.94−0.98). Each 1-MET increase was associated with a 4% reduced risk. Conclusion: Higher eCRF is associated with a lower risk of abnormal glucose. eCRF can be a vital sign used for research and prevention.

People with HIV (PWH) experience higher rates of cardiovascular events (CVEs) compared with the general population. A substantial body of evidence supports that select biomarkers of inflammation (soluble CD14 [sCD14], soluble CD163 [sCD163], highly sensitive C-reactive protein [hs-CRP], interleukin-6 [IL-6]), and coagulation (D-dimer) are elevated in PWH and related to increased rates of CVEs. Our previous work showed that smoking compared with nonsmoking was associated with significantly elevated sCD14, a biomarker of monocyte activation. We aimed to explore the effect of electronic cigarette (EC) provision on inflammatory biomarkers in PWH who smoked daily and then switched to an EC. Nineteen PWH were enrolled in a pilot study in which an EC and e-liquid were provided weekly or 8 weeks. Blood specimens for inflammatory biomarker analysis were obtained at baseline (BL) and at week 8. Biomarker levels were high at BL and did not differ significantly at week 8. There were small nonsignificant reductions in sCD163 and CRP levels. Non-significant increases in IL-6, D-dimer and sCD14 levels were also noted. Use of ECs for 8 weeks does not appear to significantly increase or decrease inflammatory biomarker levels in SWH. Further research with larger samples and a control group is needed.

Social network analysis (SNA) is an effective method for characterizing networks from various specific perspectives. Global trade contracted sharply in 2020 owing to the COVID-19 pandemic, and growth is expected to be lower than the pre-pandemic trends. This study takes countries worldwide as the primary unit of analysis and uses different procedures of social network analysis (SNA), including network density, centrality, and core-periphery structure, and applies them to the field of trade in electronic integrated circuit products (ICPT). In addition to static and descriptive analysis, this study also uses of tools such as Ucinet 6.732 for visual analysis, visual analysis, and more convenient and precise display of the network structure of ICPT. The important countries play a central role in determining the overall structural features. The core-periphery structure in the network from both spatial and temporal perspectives, data on electronic integrated circuit products for the period 2015-2021 were used in SNA. This study found that the ICPT network became denser from 2015 to 2021 but declined and picked up in 2018 and 2020. Moreover, the core-peripheral structure exists in the ICPT network. The main core network countries are Taiwan, Hong Kong, Singapore, mainland China, Malaysia, Japan, the Philippines, Thailand, Vietnam, and other Asian countries, including the United States and Germany.

(1) Background: Rational use of medicines (RUM) and their assessment is important to ensure optimal use of resources and patient care in hospitals. These assessments are essential to identifying practice gaps for quality improvement. (2) Methods: Assessment of adherence to WHO/ International Network for Rational Use of Drugs core prescribing indicators among out-patients in 2021 was conducted at the University Hospital of the Kwame Nkrumah University of Science and Technology in the Ashanti region of Ghana. We reviewed electronic medical records (EMR) of 110,280 patient encounters in the year which resulted in 336,087 medicines prescribed. (3) Results: The average number of medicines prescribed per encounter was 3 with generics being prescribed in 76% of prescriptions. Injections were prescribed in 7% of encounters while 90% of medicines were from Ghana’s Essential Medicines List 2017. (4) Conclusions: With the exception of patient encounters with injections, all prescribing indicators assessed in this study did not meet WHO optimum levels providing targets for quality improvement in RUM. Implementing prescribing guides and policies, regular audits and feedback as well as continuous professional development training may help to improve prescribing practices in the hospital.

People with diabetic foot frequently exhibit poor gait and balance. However, there is no review to inform digital biomarkers of poor gait and balance related to diabetic foot, measurable by wearables outside traditional gait laboratories. Such information could assist in designing remote patient monitoring platform to track changes in gait and balance dysfunction among people with diabetic foot for timely referral and intervention. Accordingly, we conducted a web-based review using PubMed. Our search was limited to human subjects and English-written papers published in peer-reviewed journals. We identified 20 papers in this review. We found preliminary evidence of digital biomarkers of gait and balance dysfunction in people with diabetic foot, measured by wearables, such as slow gait speed, large gait variability, unstable gait initiation, and large body sway. However, due to heterogeneities in included papers in terms of study design, movement tasks, and small sample size, more studies are recommended to confirm this preliminary evidence. Additionally, based on our review, we recommend establishing appropriate strategies to successfully implement wearable-based assessment into clinical practice for diabetic foot care.

Background: Monitoring of antibiotic prescription practices in hospitals is essential to assess and facilitate appropriate use. This is relevant to halt the progression of antimicrobial resistance. Methods: Assessment of antibiotic prescribing patterns and completeness of antibiotic prescriptions among out-patients in 2021 was conducted at the University Hospital of Kwame Nkrumah University of Science and Technology in the Ashanti region of Ghana. We reviewed electronic medical records (EMR) of 49,660 patients who had 110,280 encounters in the year. Results: The patient encounters yielded 350,149 prescriptions. Every month, 33-36% of patient encounters resulted in antibiotic prescription, higher than the World Health Organization’s (WHO) recommended optimum of 27%. Almost half of the antibiotics prescribed belonged to WHO’s Watch group. Amoxicillin-clavulanic acid (50%), azithromycin (29%), ciprofloxacin (28%), metronidazole (21%), and cefuroxime (20%) were the most prescribed antibiotics. Antibiotic prescribing parameters (indication, name of drug, duration, dose, route and frequency) were documented in almost all prescriptions. Conclusions: Extending antimicrobial stewardship to the out-patient settings by developing standard treatment guidelines, an out-patient specific drug formulary and antibiograms can promote rational antibiotic use at the hospital. The EMR system of the hospital is a valuable tool for monitoring prescriptions that can be leveraged for future audits.

The present work reports on the calculated electronic and magnetic structure of the binary Co-Ga system at high Co content. β-CoGa adopts a simple cubic CsCl type structure. Well-ordered CoGa does not exhibit collective magnetism but is a paramagnetic, metallic compound. Neither Co nor Ga deficiency induces magnetic order, however, ferromagnetism is observed for Co-Ga anti-site disorder. The magnetic moment per cell increases up to about 1.2 μB in the completely disordered body centered cubic structure. With increasing Co content, Co1+xGa1−x maintains the CsCl type structure and becomes ferromagnetic. Most important, a discontinuity of the magnetic order with composition is observed at about 10% excess Co, where a change from a low magnetic moment state to a high moment state is observed. This is accompanied by a change in the electronic structure and transport properties. The discontinuity is forced by the increasing exchange splitting related to the localized moment of the additional Co atoms that replace Ga. Subsequently, the magnetic moment increases continuously up to 2.5 μB for x=0.6. For x≳0.6, the structure changes to face centered cubic with random site occupation and the magnetic moment further increases. Above the magnetic discontinuity, the Curie temperature increases linearly with the Co content from the onset of ferromagnetism, until it reaches its maximum in pure Co.

Chirality depends on particular symmetries. For crystal structures it describes the absence of mirror planes and inversion centers, and in addition to translations, only rotations are allowed as symmetry elements. However, chiral space groups have additional restrictions on the allowed screw rotations as a symmetry element, because they always appear in enantiomorphous pairs. This study classifies and distinguishes the chiral structures and space groups. The chirality is quantified using Hausdorff distances and continuous chirality measures and selected crystal structures are reported. The chirality is discussed for bulk solids and their surfaces. Moreover, the band structure, and thus, the density of states, is found to be affected by the same crystal parameters as the chirality. However, it is independent of handedness. The Berry curvature, as a topological measure of the electronic structure, depends on the handedness, but is not a proof for the chirality because it responds on the inversion of a structure. For molecules, optical circular dichroism is one of the most important measures for the chirality. Thus, it is proposed in this study that the circular dichroism in the angular distribution of photoelectrons in high symmetry configurations can be used to distinguish the handedness of chiral solids and their surfaces.

The new need to move to an online mode of administration has necessitated the adoption of Software-as-a-Service (SaaS) and Platform-as-a-Service (PaaS). The conventional paper-based administrative memorandum is relatively costly, requires manpower, insecure and non-confidential, prone to unauthorized access and has a relatively slow cycle time; among others. An electronic memo (e-memo) can save cost, offer high speed of processing, reliability and security. The aim of this work was to conceptualize, design and develop a novel semantic web-based memo platform that allows for handling memos within an organization. The tools used include HTML, CSS, PHP, JavaScript, jQuery and AJAX, MySQL. The developed system was tested in three stages. Testing was done in the Department of Computer Science of the institution of case study, then in the Faculty of Science and finally in the entire Lagos State University. Agile development method was used in the development process. The designed system was hosted on a cloud-server and a total of 43 test cases were considered and an average of four minutes was recorded for a complete memo cycle. eMemo allows users to generate, sign, treat and memo electronically. It is such a useful tool that will enhance information processing in a faster, standardized and more secure manner.

This article discusses the use of a hand held electronic nose to obtain information on the presence of some aromatic defects in natural cork stoppers, such as haloanisoles, alkylmethoxypyrazines and ketones. The proposed prototype has been developed as an instrumentation system with up to eight commercial gas sensors. Machine learning algorithms such as k-nearest neighbors and artificial neural networks has been used. The use of this system tries to improve the current aromatic defect detection process in the cork stopper industry, which is done by gas chromatography or human test panels.

As one of the most appealing edible mushrooms, the quality of Flammulina velutipes can be affected by the cultivation substrate, which has an impact on the mushroom umami taste and nutrients. In our study, the effect of mushroom root fermentation broth (MRFB) based substrate on umami taste and nutrients of F. velutipes were evaluated; four proportions of MRFB was conducted (CK 0%, E1 6.7%, E2 13.4%, E3 20.1%). Results indicated that MRFB was an effective nutrient supplement for mushroom cultivation substrate. E2 and E3 showed higher crude fiber, crude fat, soluble protein, and soluble sugar. Compared to CK, the content of monosodium glutamate-like (MSG-like) amino acids, essential amino acids, total amino acids and total 5'-nucleotides in E2 and E3 were higher. The equivalent umami concentration (EUC) values in E1, E2 and E3 were 1.70, 2.43 and 1.56 times of CK, respectively. Higher umami, saltness and sweetness taste values were found in E2. Thereby, it signified that better umami and richer nutrients were achieved by using substrate with proper volume of MRFB, especially, E2 with 13.4% of MRFB. Overall, better mushroom quality could be derived from the application of MRFB in cultivation. MRFB was a favorable nutrient supplement for Flammulina velutipes cultivation substrate.

The one-to-one structural correspondence between any conjugated hydrocarbon CnHm and the borane BnHm+n is extended here, with the B3LYP/cc-pVDZ model, to pure conjugated carbon systems with the example of buckminsterfullerene C60 with the corresponding icosahedral isoelectronic system closo-borane B60H60, and the fluorine substituted systems B60F30H30 and B60F60 , all with icosahedral Ih symmetry. All systems correspond to energy minima in the potential energy hypersurface, except for B60(F30)in(H30)out . Selected electronic structure methods are used to characterize all systems: molecular electrostatic potentials (MEP), atomic charges, bond orders, and topological properties of the electron density within quantum theory of atoms-in-molecules (QTAIM) and electron-localization function (ELF) theory. In the particular case of B60H60 we use the recently developed Hückeloid model to characterize this system. The stability of the energy minimum icosahedral structure B60F60 could have an origin in F···F attractive interactions of the inner fluorine atoms of the cage.

Tobacco Free Nicotine (TFN) Electronic Nicotine Delivery Systems (ENDS) are yet to be classified as tobacco products; consequently, there is ambiguity over whether Food and Drug Administration (FDA) regulatory authority can be extended to include TFN e-cigarettes. In recent years, a more significant number of e-cigarette companies have been manufacturing TFN-containing e-cigarettes and e-liquids to circumvent FDA regulations. While studies have shown that aerosols generated from tobacco-derived nicotine-containing e-cigarettes contain significant Reactive Oxygen Species (ROS) levels, no comparison studies have been conducted using TFN e-cigarettes. This study uses a single puff aerosol generator to aerosolize TFN and tobacco-derived nicotine-containing vape-products and subsequently involves semi-quantifying ROS generated by these vape products in H2O2 equivalents. We found that the differences between ROS levels generated from TFN and tobacco-derived nicotine-containing vape products vary by flavor. TFN tobacco flavors and fruit flavors are more toxic in terms of ROS generation than menthol/ice and drink/beverage flavored products using TFN. The type of salt nicotine used in vape products, TFN or tobacco-derived nicotine, impacts the level of ROS generated from flavored vape products. Thus, a better understanding of the type of salt nicotine used in e-cigarettes (tobacco-derived or synthetic), has modulating effect on lung oxidative stress.

In this paper, we have shown the electronic circuit equivalence of a mechanical system consists of two oscillators coupled with each other. The mechanical design has the effects of the magnetic, resistance forces and the spring constant of the system is periodically varying. We have shown that the system’s state variables, such as the displacements and the velocities, under the effects of different forces, lead to some nonlinear behaviors, like a transition from the fixed point attractor to the chaotic attractor through the periodic and quasi-periodic attractors. We have constructed the equivalent electronic circuit of this mechanical system and have verified the numerically obtained behaviors using the electronic circuit.

For better export marketing strategies (EMS), companies mobilize their internal resources, which are managerial commitment, firm experience, and product uniqueness. However, Small businesses with constrained resources cannot be well explained with this view. So, more research on how small business come up with EMS have been called for. To explain how resource-restricted firms which rely heavely on entrepreneur, this study adopted the concept of dynamic managerial capabilities (DMCs) and resource versatility to better explain small business exports. We analyzed small businesses in Mongolia with qualitative research methods, including interviews with entrepreneurs and support organizations, site visits, and group discussions. We suggest international dynamic marketing capabilities (IDMCs), which are entrepreneurial orientation, networking capability, and versatile dynamic capability for small business. Theoretical and managerial implications are discussed.

The interfacial mechanics and electrical properties of the SiC reinforced copper matrix composites were studied via the first principles method. The work of adhesion (Wad) and the interfacial energies were calculated to evaluate the stabilities of the SiC/Cu interfacial models. The carbon terminated (CT)-SiC/Cu interfaces were predicted more stable than those of the silicon terminated (ST)-SiC/Cu from the results of the Wad and interfacial energies. The interfacial electron properties of SiC/Cu were studied via the charge density distribution, charge density difference, electron localized functions and partial density of the state. The covalent C-Cu bonds were formed based on the results of the electron properties, which further explained the fact that the interfaces of the CT-SiC/Cu are stable than those of the ST-SiC/Cu. The interfacial mechanics of the SiC/Cu were investigated via the interfacial fracture toughness and ultimate tensile stress, and the results indicate that both CT- and ST-SiC/Cu interfaces are hard to fracture. The ultimate tensile stress of the CT-SiC/Cu is nearly 23GPa, which is smaller than those of the ST-SiC/Cu of 25 GPa. The strains corresponding to their ultimate tensile stresses of the CT- and ST-SiC/Cu are about 0.28 and 0.26, respectively. The higher strains of CT-SiC/Cu indicate their stronger plastic properties on the interfaces of the composites.

Thermal simulations are an important part in the design of electronic systems, especially as systems with high power density become common. In simulation-based design approaches, a considerable amount of time is spent by repeated simulations. In this work, we present a proof-of-concept study of the application of convolutional neural networks to accelerate those thermal simulations. The goal is not to replace standard simulation tools but to provide a method to quickly select promising samples for more detailed investigations. Based on a training set of randomly generated circuits with corresponding Finite Element solutions, the full 3D steady-state temperature field is estimated using a fully convolutional neural network. A custom network architecture is proposed which captures the long-range correlations present in heat conduction problems. We test the network on a separate dataset and find that the mean relative error is around 2 % and the typical evaluation time is 35 ms per sample ( 2 ms for evaluation, 33 ms for data transfer). The benefit of this neural-network-based approach is that, once training is completed, the network can be applied to any system within the design space spanned by the randomised training dataset (which includes different components, material properties, different positioning of components on a PCB, etc.).

The conformational dependence of the matrix element for spin-orbit coupling and of the electronic coupling for charge separation are determined for an electron donor-acceptor system containing a pyrene acceptor and a dimethylaniline donor. Different kinetic and energetic aspects that play a role in the spin-orbit charge transfer intersystem crossing (SOCT-ISC) mechanism are discussed. This includes parameters related to initial charge separation and the charge recombination pathways using the (Semi-Classical) Marcus Theory for electron transfer. The spin-orbit coupling, which plays a significant role in charge recombination to the triplet state can be probed by (TD-)DFT, using the latter as a tool to understand and predict the SOCT-ISC mechanism. The matrix elements for spin-orbit coupling for acetone and 4-thio-thymine are used for benchmarking. (Time Dependent-) Density Functional Theory (DFT and TD-DFT) calculations are applied using the quantum chemical program Amsterdam Density Functional (ADF).

The copper end paste used in multilayer ceramic capacitors sintered in nitrogen atmosphere will lead to carbon residue of organic vehicle, which will lead to the reduction of electrode conduc-tivity and high scrap rate. With an attempt to leave no residue in the sintering, the compatibility of solvents and thickeners should be improved because it has an important influence on the hi-erarchical volatilization and carbon residue of organic vehicles. In this work, the volatility of different solvents was compared and several solvents were mixed in a definite proportion to prepare an organic vehicle with polyacrylate resins. The hierarchical volatility and solubility parameters of mixed solvents were adjusted effectively by changing proportions of different components, the thermogravimetric curves of resins and organic vehicles were measured by thermogravimetric analyzer, the effect of solubility parameter on the dissolvability of resins in the solvent and the residual of organic vehicles were studied. Results showed that the hierar-chical volatilization of solvents can be obtained by mixing different solvents; the intrinsic vis-cosity of the organic vehicle is higher and the thermal decomposition residue of polyacrylate resins is lower when the solubility parameters of mixed solvents and polyacrylate resins are closer. The low residual sintering of organic vehicles can be achieved by using the mixed solvent with hierarchical volatility and approximate solubility parameters as resins.

A reliable Electronic Voting Machine (EVM) is proposed and implemented in this study, which is integrated with a biometric fingerprint scanner to ensure a secure election process. This biometric EVM includes features such as an interactive user interface, hack-free design and master lock. The EVM system has the capability of registering user data and storing them in a database through proper authentication. Moreover, the system proposed lowers the requirement for human resources. This paper provides a detailed description of the systematic development of the hardware and software used. The software part includes algorithm development and implementation. A thorough and in-depth understanding of the data and the communication protocols along with the pathways used for storage of data in the devices is provided. Additionally, the cost of the system is 62.82% less than the officially existing EVM machines of India. Furthermore, this study seeks to demonstrate the benefits of such an approach from a technological and a social standpoint.

The structural, elastic, anisotropic elastic, electronic, vibrational and properties of the Perovskite type Hydrides RbXH3 (X = Be, Ca, Mg) were performed via Vienna Ab – initio Simulation Pac-kage (VASP) based on Density Functional Theory (DFT). Our results have exhibited a well-agreement with previous calculations and experiments for each compound. In order to de-termine physical properties of RbXH3 has been used the Generalized Gradient Approximation (GGA) with Perdew-Burke-Ernzerhof (PBE) functional at this study. Present compounds were found to be mechanically stable as well as their gravimetric hydrogen storage capacities has been investigated. The Perovskite type Hydrides RbBeH3 and RbMgH3 has an indirect bandgap of 0.274 eV and 2.209 eV while RbCaH3 has a direct bandgap of 3.274 eV respectively and therefo-re these compounds has shown a semiconductor behaviour at equilibrium. Besides directional dependence of anisotropic properties was visualized by representing them with maximum - mi-nimum points..

International migrants comprised 14% of the UK population in 2020, but migrant health in the UK has rarely been studied at a population level using primary care electronic health records (EHRs). Given the difficulty of determining migration status using EHRs, this study developed a migration phenotype and assessed its validity. We developed a phenotyping algorithm using codes for country of birth, visa status, non-English main/first language and non-UK origin. It was applied to a Clinical Practice Research Datalink (CPRD) GOLD database of 16,071,111 primary care patients between 1997 and 2018. We compared the completeness and representativeness of the identified migrant population to Office for National Statistics (ONS) country of birth and 2011 census data by year, age, sex, geographic region of birth and ethnicity. Between 1997-2018, 403,768 migrants (2.51% of the CPRD GOLD population) were identified using the phenotype. 178,749 (1.11%) of these migrants were identified by codes indicating foreign country of birth or visa status, 216,731 (1.35%) a non-English main/first language, and 8,288 (0.05%) non-UK origin. The cohort was similarly distributed compared to ONS migration statistics in terms of sex and region of birth. Recording of migration improved from identifying approximately one-tenth of the expected proportion of migrants according to the ONS in 2004 to a quarter in 2018. Younger migrants were better represented than those aged 50 and over. The migration phenotype identified a large number of migrants and can be used to undertake large-scale migration health research in CPRD GOLD to inform healthcare policy, practice and action. While the cohort was representative of the UK migrant population in terms of sex and region of birth, migration status was under-recorded in earlier years and older ages, and future studies for these groups should therefore be interpreted with caution.

We report morpho-structural properties and charge conduction mechanisms of a foamy “graphene sponge”, having a density as low as ≈ 0.07 kg/m3 and a carbon to oxygen ratio C:O ≃ 13:1. The spongy texture analysed by scanning electron microscopy is made of irregularly-shaped millimetres-sized small flakes, containing small crystallites with a typical size of ≃ 16.3 nm. A defect density as high as ≃ 2.6×1011 cm−2 has been estimated by the Raman intensity of D and G peaks, dominating the spectrum from room temperature down to ≃ 153 K. Despite the high C:O ratio, the graphene sponge exhibits an insulating electrical behavior, with a raise of the resistance value at ≃ 6 K up to 5 orders of magnitude with respect to the room temperature value. A variable range hopping (VRH) conduction, with a strong 2D character, dominates the charge carriers transport, from 300 K down to 20 K. At T&lt; 20 K, graphene sponge resistance tends to saturate, suggesting a temperature-independent quantum tunnelling. The 2D-VRH conduction originates from structural disorder and is consistent with hopping of charge carriers between sp2 defects in the plane, where sp3 clusters related to oxygen functional groups act as potential barriers.

A conventional electrical grid mostly depends on the electrical power generated from fossil fuels. However, the pollutants from fossil fuels are the key factors for adverse climate change. Most of the developed countries of the world have already recognized the fact that the energy mix requires to be diversified by incorporating renewable energy. This is especially relevant for many of the member countries of the Organization of Islamic Cooperation (OIC), consisting of 57 countries, whose abundance of fossil fuel reserve indicates that much of their electric power is still generated from fossil fuels. In order to integrate renewable energy sources into the hybrid energy mix, an existing conventional grid needs to undergo drastic changes. Alongside this, the population boom in the OIC member countries has caused higher demand for a steady supply of electricity that the conventional grids have long been struggling to cope with. With a view to solving this multifaceted problem, incorporation of the smart power management schemes is indispensable using a smart electrical grid, where information and communications technology is integrated into its major building blocks. This allows advanced applications of a grid, such as the formation of micro-grids, demand-side management, energy storage, high-tech power electronic converters, etc. As the smart grids are being adopted by many developed countries, it is high time for the OIC member countries to pay due attention to this development, if they have not already done so. This paper explains, with special focus on the OIC member countries, the various smart power management technologies, their operations and applications, and the benefits and challenges. Then it goes on to carry out the Strength-Weakness-Opportunity-Threat with Analytical-Heuristic-Procedure (SWOT-AHP) analysis to evaluate its feasibility of incorporation and the underlying strategies appropriate for its implementation. Furthermore, a Hybrid Multi-Criteria-Decision-Making (MCDM) analysis is performed to evaluate the sequence of the emphasis that should be given on each of the technologies from those available for the smart power management initiative. Finally, the study reinforces the stance by drawing parallels from the UN Sustainable Development Goals (SDG) and highlights the importance of the smart grid in line with the global vision of SDG. This paper aims at assisting the decision-makers in implementing smart power management schemes in the OIC member countries, in particular, and other countries of the world, in general.

Medical records contain many terms which are difficult to process. Our aim in this study is to allow the visual exploration of the information in medical databases where the texts presents a large number of syntactic variations and abbreviations, through an interface which facilitates content identification, navigation and information retrieval. We propose the use of multi-term tag clouds as content representation tools and as assistants for the browsing and querying tasks. The tag cloud generation is achieved through a novelty mathematical method that allows related terms to remain grouped together within the tags To evaluate this proposal, we have used a database with 24,481 records. 23 expert users in the medical field were tasked to complete a survey to evaluate the generated tag clouds properties and we obtained a precision of 0.990, a recall of 0.870 and a F1score of 0.904 in the evaluation of the tag cloud as an information retrieval tool. The main contribution of this approach is that we automatically generate a visual interface over the text capable of capturing the semantics of the information and facilitating access to medical records.

The absolute absorption cross section of the ethyl peroxy radical, C2H5O2, in the Ã←X ̃ electronic transition with the peak wavelength at 7596 cm-1, has been determined by the method of dual wavelengths time resolved continuous wave cavity ring down spectroscopy. C2H5O2 radicals were generated from pulsed 351 nm photolysis of C2H6/Cl2 mixture in presence of O2 and detected on one of the CRDS paths. Two methods have been applied for the determination of the C2H5O2 absorption cross section: (i) based on Cl-atoms being converted alternatively to either C2H5O2 by adding C2H6 or to hydro peroxy radicals, HO2, by adding CH3OH to the mixture, whereby HO2 was reliably quantified on the second CRDS path in the 21 vibrational overtone at 6638.2 cm-1 (ii) based on the reaction of C2H5O2 with HO2, measured under either excess HO2 or under excess C2H5O2 concentration. Both methods lead to the same peak absorption cross section of C2H5O2,7596 cm-1 = (1.0±0.2) × 10-20 cm2. The rate constant for the cross reaction between of C2H5O2 and HO2 has been measured to be (6.5±1.6) × 10-12 cm3 molecule-1 s-1.

The Lamiaceae belong to the species-richest families of flowering plants and harbor many species used as herbs or for medicinal applications, such as Basils or Mints. Evolution of this group has been driven by chemical speciation, mainly of Volatile Organic Compounds (VOCs). The commercial use of these plants is characterized by a large extent of adulteration and surrogation. To authenticate and discern the species, is, thus, relevant for consumer safety, but usually requires cumbersome analytics, such as Gas Chromatography, often to be coupled with Mass Spectroscopy. We demon-strate here that quartz-crystal microbalance (QCM)-based electronic noses provide a very cost-efficient alternative, allowing for a fast, automated discrimination of scents emitted from leaves of different plants. To explore the range of this strategy, we used leaf material from four genera of Lamiaceae along with Lemongrass as similarly scented, but non-related outgroup. In order to unambiguously differentiate the scents from the different plants, the output of the 6 different SURMOF/QCM sensors was analyzed using machine learning (ML) methods, together with a thorough statistical analysis. The exposure and purging datasets (4 cycles) obtained from a QCM-based, low-cost homemade portable e-Nose were analyzed with Linear Discriminant Analysis (LDA) classification model. Prediction accuracies with repeating test measurements reached values of up to 90%. We show that it is not only possible to discern and identify plants on the genus level, but even to discriminate closely related sister clades within a genus (Basil), demonstrating that e-Noses are a powerful technology to safeguard consumer safety against the challenges of globalized trade.

In this ‘New Normal' post-COVID-19 modern world, people's health is becoming increasingly important to track. An advanced technology that uses sensory instruments to track and record critical parameters and communicates with others is the need of the time. It's difficult to keep track of all of the medical parameters and post-operative data of people with non-communicable diseases like diabetes and heart disease on a continuous basis. The system discussed here to be designed for patients who are confined to their homes, particularly when going out and being exposed to the outer world is prohibited. This paper proposed a groundbreaking health management system based on the Internet of Things (IoT) for accessing patient medical parameters in both local and remote areas. When a person's wellbeing becomes urgent, this initiative seeks to send an emergency alert to family members or loved ones. A cloud server records data from the patient's temperature sensor and pulse sensor; the data is analyzed using support vector machine algorithms to identify irregular conditions, and an emergency message is sent to the rest of the family via a mobile application, as well as a warning message to the nearest hospital.

Electronic Health Record (EHR) is being used in most healthcare institutions to preserve and share health records instead of a paper-based method. Data records must be exchanged amongst various parties and users' privileges to manage access to their records should also be provided. In addition to the basic standards of secrecy, confidentiality and integrity of information, these facts further demonstrate the need for interoperability and consumer control to access their personal data. Electronic Health Record (EHR) system faces issues of protection of data, trust and management issues. In recent Covid-19 pandemic, various applications, tools and websites were launched that stores records. Also, many personal records related to health need to be shared among different parties for early detection, contact tracing, monitoring and the future prediction that requires accurate and reliable data. Simultaneously, the citizens will be hesitant in providing their personal details due to privacy concerns and social stigma. Blockchain technology has arisen as a powerful technology that can offer the immutability, confidentiality and user access properties of stored information and provided distributed storage. This paper analyses the blockchain suitability in EHR and its further applications in efficient Covid-19 pandemic management.

This review article is focused on the analysis of the state of the art of sensors for guided 9 ultrasonic waves for the detection and localization of impacts, therefore of interest for the structural 10 health monitoring (SHM). The recent developments in sensor technologies are then reported and 11 discussed through the many references in recent scientific literature. The physical phenomena re-12 lated to impact event and the main physical quantities are then introduced to discuss their im-13 portance in the development of the hardware and software components for SHM systems. An im-14 portant aspect of the article is the description of the different ultrasonic sensor technologies cur-15 rently present in the literature and what advantages and disadvantages they could bring, in relation 16 to the various phenomena investigated. In this context, the analysis of the front-end electronics is 17 deepened, the type of data transmission both in terms of wired and wireless technology and in terms 18 of online and offline signal processing. The integration aspects of sensors for the creation of net-19 works with autonomous nodes with the possibility of powering through energy harvesting devices 20 and the embedded processing capacity is also studied. Finally, the emerging sector of processing 21 techniques using deep learning and artificial intelligence concludes the review by indicating the 22 potential for the detection and autonomous characterization of the impacts.