This work studied sorption regularities and assessed thermal stability and resistance to microbial degradation of humic acid as a result of 3 sorption cycles on bentonite clay, kaolinite, and muscovite using TGA/DSC, XRD, hydrophobic chromatography, light and electron microscopy, etc. The experiment revealed that kaolinite sorbed more humic acids (HAs) in terms of unit surface area (1.03 × 10-3 C, g/m2) compared to bentonite (0.35 × 10-3 C, g/m 10-3 g/m2). Sorption at pH 4.5 was accompanied by HA fractionation in amphiphilicity and chemical composition. HA was sorbed mainly due to hydrophobic components on the surface of all sorbents. HA was not intercalated into the interlayer spaces of montmorillonite during sorption. Sorption due to hydrophilic interactions was mostly performed on muscovite and bentonite than on kaolinite. Sorption was followed by a change in the chemical composition of HA and decreased C/N compared to free HA, indicating selective sorption of nitrogen-containing compounds which is most characteristic of muscovite. Only a relatively thermolabile HA fraction was adsorbed on all minerals while its thermal stability increased compared to that before the experiment. Thermal stability and ratio of the Exo2/Exo1 peak areas on the DSC curves of sorbed HA increased with each subsequent sorption cycle. Thermal stability and resistance to microbial oxidation of sorbed HA showed the following relationship: the higher the thermal stability, the less available is sorbed HA for utilization by microorganisms.

Thermal comfort is extremely important in architecture, especially in environments with more people spending longer on studies or intellectual activities. This research describes a case study to investigate university buildings' energy and thermal performance as a part of the ANEEL program. Due to this importance, and the need to save energy in Brazilian public buildings, the ANEEL-the Brazilian Energy Electricity Regulatory Agency, launched 2016 a national program focusing on energy efficiency in public universities around the country. University offices and classrooms require high intellectual effort; thus, environmental comfort is critical for maintaining its users' physical and mental health. This study included a pre-diagnosis of the performance of the envelope, lighting, and air conditioning systems and a survey about the quality of the environments from the users' point of view. The Prescriptive Method of the Brazilian Labeling Program (PBE) for Commercial, Service, and Public Buildings (RTQ-C) assessed the building performance. Statistical analysis was applied to correlate the quality and thermal preference of the users from the PMV/PPD. The results showed a high rate of thermal discomfort in both environments of the studies, even when using air conditioning.

The development of good conductivity p-type β-Ga2O3 is critical to realize its devices and applications. The nitrogen-doped p-type β-Ga2O3 films with enhanced conductivity characteristics were prepared through the thermal oxidation of GaN in the N2O atmosphere. Further measurements were performed on the oxidized films at 1000, 1050, and 1100 °C to have insight into the underlying mechanism of the thermally activated transformation process. The room temperature photoluminescence (PL) spectra demonstrated a moderate ultraviolet emission peak at 246 nm, confirming the generation of gallium oxide with a band gap of ~5.0 eV. The normalized X-ray diffraction (XRD), the high-resolution transmission electron microscopy (HRTEM), and the selected area electron diffraction (SAED) patterns were used to confirm the characteristic of polycrystalline and anisotropic growth. Then, the effects of the oxidation temperature on the amount of incorporated nitrogen were analyzed using secondary ion mass spectrometry (SIMS). Moreover, the ionization energy of the acceptor of films oxidized at 1000, 1050, and 1100 °C was calculated and analyzed using the temperature-dependent Hall test results. The results showed that nitrogen doping was the main contributor to p-type electrical properties. The activation energy of the polycrystalline β-Ga2O3 prepared through thermal oxidation of GaN in the N2O atmosphere was estimated to be 147.175 kJ·mol-1 using the Arrhenius plot, which was considerably lower than that of both dry and wet oxidations of GaN in O2 ambient, thus confirming the efficiency of thermal oxidation of GaN in N2O.

The study of energy sources has been an awareness of the modern world due to constraints on the current energy worldwide supply chain. The complexity of the theme as well as the consciousness of finite sources also the need of saving energy has become a priority. Although many papers have moved in this direction there is no record of papers studying the variables in a house heating system, which represents the highest energy consumption in many cold countries. This paper explores the energy-saving theme by studying the main variables present in houses’ heating systems in the winter season in cold countries like Canada, Russia, Norway, Iceland, Finland, etc. By using a novel combination of numerical thermal simulation by COMSOLTM and statistical analysis by MiniTabTM , it was possible to design an efficient thermal distribution in a house with the variables of the system by determining their significance and interaction qualitatively.

Salmorejo is a homogenate based on tomato, olive oil and breadcrumbs commercialized as a “fresh-like” cold puree in Spain and other European countries. Salmorejo is thermolabile and requires pasteurising upon High Temperature, Short Time (HTST) conditions to inhibit microbes and enzymes. Due to its penetration, dielectric heating by radiofrequency (RF) might improve pasteurisation results of conventional heating (CH) in viscous products. The objective was to validate the pasteurisation temperature (70-100 °C, at 5 ºC intervals) for salmorejo processed by radiofrequency (operating at 27.12 MHz for 9.08 s) or conventional continuous heating. Salmorejo was prone to thermal damage upon HTST conditions. Main heat-induced changes include: orangeness, flavour homogenisation, loss of freshness, thickening, loss of vitamin C and lipid oxidation. A ‘fresh-like’ good quality salmorejo can be obtained using either conventional or radiofrequency pasteurisers. Both CH and RF equivalent treatments allowed a strong reduction of total and sporulated mesophilic microorganisms, and an adequate inhibition of the pectinmethylesterase, peroxidase and, to a lesser extent, polyphenoloxidase, but did not inhibit the polygalacturonase enzyme. Pasteurisation at 80 °C for 9.8 s (RF) or 10.9 s (CH) provided a good equilibrium in levels of microbiological and enzymatic inhibition and thermal damage to the product. Increasing this temperature does not improve enzyme inactivation levels and salmorejo may become overheated.

The disc brake rotors are designed to withstand both, Maximum possible deceleration (emergency braking) and a series of frequent braking cycles. A effective rotor design and superior heat dissipating material provide better performance during the braking mechanism. In this experiment, modified ventilated disk brake rotors are developed with holes and slots and the stress, deformation, heat flux and temperature distribution has been analysed. Designing of the Finite element models of the rotor are created with SolidWorks and simulated using ANSYS. Structural and thermal characteristics are compared with a reference disk brake rotor of the motorcycle (TVS Apache RTR180). It is found that the modified rotors outperform the conventional one in terms of stress generation, temperature distribution and deformation. Furthermore, this Analysis helps us to find out the best suited material for one of the proposed designs. This experiment provides us an insight of the structural and thermal characteristics of the geometrically modified rotor that can be used to upgrade and outperform the current disc brake rotor used in the motorcycle (TVS Apache RTR180).

(1) Background: This article presents a study that aims to provide a precise understanding of the temperature distribution within a Whole-Body Cryostimulation (WBC) chamber, whether it is empty or occupied by one or several individuals.; (2) Methods: The study employs a mixed numerical and experimental approach, utilizing simplified Computational Fluid Dynamics (CFD) simulations and an experimental analysis that employs thermocouples to determine the 3D thermal field in actual conditions.; (3) Results: The results reveal a non-negligible temperature difference between the setpoint and actual temperature in the middle of the cryochamber. Furthermore, it is shown that the presence of individuals inside the chamber results in both an average temperature rise and a more heterogeneous thermal behavior, which appear to be associated with the number of individuals present.; (4) Conclusions: The findings of this study emphasize the need for further research to establish temperature guidelines and standardize measurement methods for effective WBC treatment.

1D spin crossover (SCO) solids which convert between the low-spin (LS) and the high-spin (HS) states are widely studied in the literature due to their diverse thermal and optical characters which allows obtaining many original behaviors, such as large thermal hysteresis, incomplete spin tran-sitions, as multi-step spin transitions with self-organized states. In the present work, we investigate the thermal behaviors of a system of two-elastically coupled 1D mononuclear chains, using the electro-elastic model, by including an elastic frustration in the nearest neighbors (nn) bond length distances of each chain. The chains are made of SCO sites that are coupled elastically through springs with their nn and next-nearest neighbors. The elastic inter-chain coupling includes diagonal springs, while the nn inter-chains distance is fixed to that of the high-spin state. The model is solved using MC simulations, performed on the spin states and the lattice distortions. When we only frustrate the first chain, we found a strong effect on the thermal-dependence of the HS fraction of the second chain, whose, by lowering its transition temperature which is also accompanied with the appearance of a significant residual HS fraction at low temperature. In the second step, we frustrate both chains by imposing different frustration rates and found that, for high frustration values, the thermal dependence of the total HS fraction exhibits three step and even four step spin transitions. The careful examination of the spin state structures in the plateau regions revealed the existence of special antiferro-elastic structure of type LSLS-HSHS-LSLS-HSHS along the first chain, and HSHS-LSLS-HSHS-LSLS along the second, also showing that the two chains seem to be antifer-ro-elastically coupled. This type of organization is interesting, because it anticipates the possible existence of periodic structures made of alternate 1D antiferro-like HS-LS strings coupled in the ferro-like fashion along the interchain direction in the 2D case.

This article provides insight into flow measurement techniques in water injection wells in oil production fields, with a particular focus on the initial phases of operation. Consequently, the method created by Ramey in 1962, originally intended for estimating the temperature of the injection fluid, has been adapted to calculate the flow rate. In this technique, the calculation This procedure is based on the correlation between the thermal flux formed in the well. The discrepancy between the temperatures of the injected liquid and the geothermal temperature of the reservoir is the main source of the systematic errors in Ramey’s technique. To a lesser extent, but still significant, failure to observe the injection time in a fluid variation also results in an error problem that needs the failure to adhere to the scheduled injection time for a fluid alteration also yields a notable error dilemma that needs to be fixed. The reduction of listed systematic errors is the product of the main part of this article.

In this article, we analyze the thermodynamics, thermal fluctuations and quasi-normal modes of a torus-like charge AdS black hole. The parameters of a torus-like charged AdS black hole are its mass, electric charge, and cosmological constant. We used a torus-like charge AdS black hole to evaluate thermodynamics through thermal fluctuations and found that it significantly affected the corrected thermodynamic potentials. Black holes of larger radii are more stable and significant. The effect of thermal fluctuation has been investigated on the other thermodynamic potentials such as the Hemohltz free energy, Gibbs free energy, enthalpy, and specific heat, using the concept of corrected entropy. Finally, we use null geodesics to deal with quasi-normal modes. The null geodesics provide the photon sphere angular velocity and Lyapunov exponent, which are the real and imaginary components of the quasi-normal modes in the eikonal limit. With inceasing charge and photon radius, angular velocity reaches its maximum, similar to Lyapunov's exponent.

An increasing ecological phase-shift from coral dominated reefs to macroalgae dominated reefs as a result of anthropogenic impacts, such as eutrophication, sedimentation, and overfishing, has been observed in many reef systems around the world. Ocean warming is a universal threat to both corals and macroalgae, which may alter the outcome of competition between them. Therefore, in order to explore the effects of indirect and direct exposure to macroalgae on the physiological, biochemical, and genetic expression of corals at elevated temperature, the coral Acroproa hyacinthus and highly invasive green algae Caulerpa taxifolia have been chosen. Physiologically, the results exhibited that distinguish from control and direct contact treatments, the density and chlorophyll a content of zooxanthella decreased by 53.1% and 71.2% respectively, when coral indirect contacted with algae at ambient temperature (27°C). Besides, enzyme activities of superoxide dismutase (SOD) and catalase (CAT) in coral tissue were enhanced by interacting with algae. After an increase of 3°C, the density and chlorophyll a content of zooxanthella reduced by 84.4% and 93.8% respectively, whereas the enzmy activities of SOD and CAT increased by 2.3 and 3.1-fold. However, only the zooxanthellae density and pigment content decreased when C.taxifolia co-culture with A.hyacinthus at 30°C. Molecularly, different from the control group, the differentially expressed genes (DEGs) such as Rab family, ATG family and Casp7 were significantly enriched in endocytosis, autophagy and apoptosis pathways , regardless whether A.hyacinthus was indirect or indirect exposure to C.taxifolia at 27°C. Under thermal stress without algae interaction, the DEGs were significantly enriched in microbial immune signal transduction pathways, such as Toll-like receptor signaling pathway and TNF signaling pathway, while multiple cellular immunity (IFI47, TRAF family) and oxidative stress (CAT, SODC, HSP70) genes were up-regulated. Inversely, compared with corals without interaction with algae at 30°C, the DEGs of corals interacted with C.taxifolia at 30°C, were remarkably enriched in apoptosis, NOD-like receptor signaling pathway, including the transcription factors such as Casp family, TRAF family. In conclusion, the density and chlorophyll a content of zooxanthella remained a fading tendency induced by macroalgae at ambient temperature. The oxidative stress and immune response levels of coral has been elevated at 30°C, but macroalgae alleviated the negative effects triggered by thermal stress.

The mining sector generates a substantial quantity of stone waste and tailings, which constitutes an environmental risk. The most prevalent method for disposing of this industrial waste is dumping, which contributes to soil deterioration and water contamination while acquiring precious land. It can be recycled using a number of processes, such as the promising geopolymerization technique, which transforms waste into value. This study reviews current developments in the manufacturing of mine tailings-based geopolymer composites from industrial waste as a possible sustainable building material. This paper also gives in-depth studies on the characteristics and behaviors of mine tailings composites used in geopolymer manufacturing, including durability, microstructure, thermal and leaching properties. This review also identifies knowledge gaps that must be filled in order to advance mine tailings composites for geopolymers.

We experimentally investigate power-sensitive photo-thermal tuning (PTT) of two-dimensional (2D) graphene oxide (GO) films coated on integrated optical waveguides. We measure the light power thresholds for reversible and permanent GO reduction in silicon nitride (SiN) waveguides integrated with 1 and 2 layers of GO. Raman spectra at different positions of a hybrid waveguide with permanently reduced GO are characterized, verifying the inhomogeneous GO reduction along the direction of light propagation through the waveguide. The differences between the PTT induced by a continuous-wave laser and a pulsed laser are also compared, confirming that the PTT mainly depend on the average input power. These results reveal interesting features for 2D GO films coated on integrated optical waveguides, which are of fundamental importance for the control and engineering of GO’s properties in hybrid integrated photonic devices.

The problem of water drinking supply is very important in the world, especially for developing countries, in particular Algeria. In this work we propose to study a distillation system based on solar energy process using an artificial intelligence approach in order to enhance the performance and the daily production. For this purpose, a conventional solar still and capillary film solar still was used. The operating parameters of the two distilleries are analyzed and the neural network approach was used to predict the performance through the amount of distillate, solar radiation and ambient temperature. The sensitivity between the operating parameters of the solar still for two case have been studied through the artificial neuron network model. The obtained results are promising, analyzed and discussed.

Undisturbed ground temperature (UGT), thermal conductivity (TC) and heat capacity (HC) are essential parameters for the design of borehole heat exchanger (BHE) and borehole thermal energy storage systems. However, field methods to assess the thermal state and properties of the sub-surface are costly and time consuming. Moreover, HC is often not evaluated but arbitrarily selected from literature considering the geological materials intercepted by boreholes. Therefore, this work aims at proposing a field heat tracing method to infer the thermal diffusivity (TD) and HC with assumption of natural transient heat conduction in the subsurface. Empirical equations were developed to reproduce a UGT profile measured along a BHE. Experimental coefficients are found with a non-linear least square solver optimization and used to calculate the damping depth and TD. Subsequently, the TD is used to evaluate HC considering TC obtained from a thermal response test (TRT). Results from this proposed heat tracing method were verified and validated against a set of TRT results and oscillatory TRT analysis using a field dual probe concept to infer HC. The example here described highlights the advantages and novelty of this fast and simple field method relying only on a single UGT profile measured before a TRT.

Electric Vehicles (EVs) are the need of the hour due to growing climate change problems linked with the transportation sector. Battery Thermal Management System (BTMS), which is accountable for certifying safety and performance of lithium-ion batteries (LiB), is the most vital part of an EV. LiB has auspicious gravimetric energy density but the heat generation due to chemical reactions inside a LiB during charging and discharging causes temperature rise which has a direct effect on LiB performance and safety. This study specifically focuses on aircooled BTMS, defines different types of air-cooled BTMS (active and Passive), discusses limitations associated with air-cooled BTMS, and investigates different optimization techniques and parameters to improve performance of air-cooled BTMS. Maintaining temperature within optimum range and uniform temperature distribution between cells of a battery pack are the major design parameters for improving the performance and efficiency of air-cooled BTMS. Various optimization techniques including cell arrangement with a battery pack, air-flow channel optimization, and air inlet/outlet position variations are discussed and each technique is thoroughly reviewed. Finally, it’s noted that passive air-cooled BTMS is not that effective for long-distance vehicles so most researchers shifted their focus toward active air-cooled BTMS. Active air-cooled BTMS requires a lot of power for effective performance. Lastly, the most recent field of air-cooled BTMS technology which is Air-Hybrid BTMS is discussed and declared a very promising solution for overcoming major limitations associated with air-cooled BTMS.

The deep geothermal industrial project at Soultz-sous-Forêts is located in the Upper Rhine Graben, France. As part of the MEET project, this study aims to evaluate the possibility of extracting higher amounts of energy from the existing industrial infrastructure. To achieve this objective, the effect of reinjecting fluid at lower temperature than the current fluid injection temperature of 70 ℃ was modelled and the drop in the production wellhead temperature for 100 years of operation was quantified. Two injection-production rate scenarios were considered and compared for their effect on overall production wellhead temperature. For each scenario, reinjection temperatures of 40 ℃, 50 ℃ and 60 ℃ were chosen and compared with the 70 ℃ injection case. For the lower production rate scenario, the results show that the production wellhead temperature is approximately 1-1.5 ℃ higher than for the higher production rate scenario after 100 years of operation. In conclusion, no significant thermal breakthrough has been observed with the applied flow rates and lowered injection temperatures even after 100 years of operation.

This paper proposes the localisation of room occupants in home environments using Unobtrusive Sensing Solutions (USSs). The ability to localise room occupants in home environments can help in the objective monitoring of sedentary behaviour. While wearable sensors can provide tangible information on health and wellness, they have battery life issues and the inability to perform prolonged monitoring. This work uses heterogeneous USSs in the form of an Infrared Thermopile Array (ITA-64) thermal sensor and a Multi-Chirp Frequency Modulated Continuous Wave Mono-pulse (MC-FMCW-M) Radar sensor to monitor room occupants. Digital filters and background subtraction algorithms were used to process the thermal images gleaned from the ITA-64 thermal sensors. The MC-FMCW-M Radar sensor used multi-chirp and Doppler shift principles to estimate the exact location of the targeted room occupants. The estimated distances from the Radar Sensor were compared with ground truth values. Experimental results demonstrated the ability to identify thermal blobs of occupants present in the room at any particular time. Data analyses indicated no significant difference (p = 0.975) and a very strong positive correlation (r = 0.998) between the ground truth distance values and those obtained from the Radar Sensor.

Lignocellulosic fibers are widely applied as composite reinforcement due to their properties. The thermal degradation behavior determines the maximum temperature in which the fiber can be applied without significant mass loss. It is possible to determine these temperatures using Thermogravimetric Analysis (TG). In particular, when curves are obtained at different heating rates, kinetic parameters can be determined and more detailed characteristics of the material are obtained. However, every curve obtained at a distinct heating rate demands material, cost, and time. Methods to predict thermogravimetric curves can be very useful in the materials science field and in this sense mathematical approaches are powerful tools if well employed. For this reason, in the present study, curaua TG curves were obtained at three different heating rates (5, 10, 20, and 40 °C.min-1) and Vyazovkin kinetic parameters were obtained. After, the experimental curves were fitted using an artificial neural network (ANN) approach followed by a Surface Response Methodology (SRM). Curves at any heating rate between the minimum and maximum experimental heating rates were obtained with high reliability. Finally, Vyazovkin kinetic parameters were tested again with the new curves showing similar kinetic parameters from the experimental ones. In conclusion, due to the capability to learn from the own data, ANN combined with SRM seems to be an excellent alternative to predict TG curves that do not test experimentally, opening the range of applications.

Metal foams are widely studied as possible tools for the enhancement of heat transfer from hot bodies. The basic idea is that a metal foam tends to increase significantly the heat exchange area between the hot solid body and the external cooling fluid. For this reason, this class of porous materials are considered as good candidates for an alternative to finned surfaces, with different pros and cons. Among the pros, we mention the generally wider area of contact between solid and fluid. Among the cons is the difficulty of producing different specimens with the same inner structure, with the consequence that their performance may be significantly variable. This paper will offer a survey of the literature with a focus on the main heat transfer characteristics of the metal foams. Then, a numerical simulation of the heat transfer at the pore scale level for an artificial foam with a spatially periodic structure will be discussed. Finally, these numerical results will be employed to assess the macroscopic modelling of the flow and heat transfer in a metal foam.

The temperature of the indoor environment is important for health and wellbeing especially at the extremes of age. The study aim was to undertsand the relationship between self-reported thermal sensation and extremity skin temperature in care home residents with and without dementia. The Abbreviated Mental Test (AMT) was used to discriminate residents to two categories, those with and those without dementia. After acclimatisation, measurements included: tympanic membrane temperature, thermal sensation rating followed by infrared thermal mapping of non-dominant hand and forearm. Sixty-nine afebrile adults (60-101 years of age) were studied in groups of two to five, in mean ambient temperatures of 21.4^oC-26.6^oC (median 23.6^oC). Significant differences were observed between groups; thermal sensation rating (p=0.02), tympanic temperature (p=0.01), fingertip skin temperature (p=0.01) and temperature gradients; fingertip-wrist p=0.001 and fingertip-distal forearm, p=0.001.

Flexibility of polymers defined by an equation in 2019 is related here to thermal conductivity, using reliable data for both properties found in the literature. The resulting equation is simple, it has the form of a quadratic polynomial. The goodness of the fit represented by R² = 0.975, while R² = 1 represents a perfect fit. Thus, knowledge of one of these properties can be used for calculation of the other one. The present results are a part of a larger program enabling obtaining by calculation pertinent properties of polymers from other properties for which data are available.

The concept of using special electrical circuit design realize a "cold resistors", that is, an active resistor circuitry with lowered effective noise temperature, was first introduced about 80 years ago. Later on, various kinds of artificial resistors were applied in different research areas, such as gravitational wave detection, photo-amplifiers and quartz oscillators. Their proofs of concepts were experimentally proved. Unfortunately, the complete theory was not found even though several attempts had been published, sometimes with errors. In this paper, we describe a correct and complete circuit theoretical model of a cold resistor system. The results are confirmed by computer simulations. A design tools for this circuit is also shown.

The experimental determination of the relative biological effectiveness of thermal neutron factors is fundamental in Boron Neutron Capture Therapy. Present values have been obtained using mixed beams consisting of both neutrons and photons of various energies. A common weighting factor has been used for both thermal and fast neutron doses, although such an approach has been questioned. At the nuclear reactor of the Institut Laue-Langevin a pure low-energy neutron beam has been used to determine thermal neutron relative biological effectiveness factors. Different tumor cell lines, corresponding to glioblastoma, melanoma, and head and neck squamous cell carcinoma, and non-tumor cell lines (lung fibroblast and embryonic kidney) have been irradiated using an experimental arrangement designed to minimise neutron-induced secondary gamma radiation. Additionally, the cells were irradiated with photons at a medical linear accelerator, providing reference data for comparison with that from neutron irradiation. Survival and proliferation were studied after irradiation, yielding the Relative Biological Effectiveness corresponding to the damage of thermal neutrons for the different tissue types.

Pistachio and cashew contain allergenic proteins, which causes them to be removed from the diet of allergic people. Former evidences have demonstrated that food processing (thermal and non-thermal) can produce structural and/or conformational changes in proteins by altering their allergenic capacity. In this study, the influence of Instant Controlled Pressure Drop (DIC) on the pistachio and cashew allergenic capacity has been studied. Western blot was carried out using IgG anti-11S and anti-2S and IgE antibodies from sera of patients sensitized to pistachio and cashew. DIC processing causes changes in the electrophoretic pattern, reducing the number and intensity of protein bands, as the pressure and temperature treatment increment what results in a remarkable decrease of detection of potentially allergenic proteins. The harshest conditions of DIC (7bar, 120s) markedly reduce the immunodetection of allergenic proteins, not only by using IgG (anti 11S and anti 2S) but also when IgE sera from sensitized patients were used for Western blots. Such immunodetection is more affected in pistachio than in cashew nuts, but it not completely removed. Therefore, cashew proteins are possibly more resistant than pistachio proteins. According these findings, Instant Controlled Pressure Drop (DIC) can be considered a suitable technique in order to obtain hypoallergenic tree nuts flour to be used in food industry.

Thermophysical characterization of three paraffin waxes (RT27, RT21 and RT35HC) is carried out in this study using DSC, TGA and transient plane source technics. Then, a numerical study of their melting in a rectangular enclosure is examined. The enthalpy-porosity approach is used to formulate this problem in order to understand the heat transfer mechanism during the melting process. The analysis of the solid-liquid interface shape, the temperature field shows that the conduction is the dominant heat transfer mode in the beginning of the melting process. It is followed by a transition regime and the natural convection becomes the dominant heat transfer mode. The effects of the Rayleigh number and the aspect ratio of the enclosure on the melting phenomenon are studied and it is found that the intensity of the natural convection increases as the Rayleigh number is higher and the aspect ratio is smaller. In the second part of the numerical study, a comparison of the performance of paraffins waxes during the melting process is conducted. Results reveals that from a kinetically RT21 is the most performant but in term of heat storage capacity, it was inferred that RT35HC is the most efficient PCM.

In recent years, it has been found in engineering practice that the service life of cemented carbide shield machine tools used in uneven soft and hard strata is substantially reduced. The study found that thermal stress is the main reason for the failure of cemented carbide shield tunneling tools when shield tunneling is carried out in uneven soft and hard soil. To maintain the hardness of cemented carbide, improving the thermal conductivity of the shield machine tool is of great importance for prolonging its service life and reducing engineering costs. In this paper, graphene and carbon nanotubes were mixed with WC-Co powder and sintered by SPS (Spark Plasma Sintering). The morphology was observed by using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). A Rockwell hardness tester and bending strength tester were used to test hardness, bending strength and thermal conductivity. The results show that adding trace graphene or carbon nanotubes can increase the bending strength of the cemented carbide by approximately 50% while keeping the hardness of the cemented carbide unchanged. The thermal conductivity of the cemented carbide can be increased by 10% with the addition of 0.12% graphene alone.

Abstract: Currently, thermal power is the largest source of power in the world. Although the impacts of climate change on cooling water sufficiency in thermal power plants have been extensively assessed globally and regionally, their economic consequences have seldom been evaluated. In this study, the Asia-Pacific Integrated Model Computable General Equilibrium model (AIM/CGE) was used to evaluate the economic consequences of projected future cooling water insufficiency on a global basis, which was simulated using the H08 global hydrological model. This approach enabled us to investigate how the physical impacts of climate change on thermal power generation influence economic activities in regions and industrial sectors. To account for the uncertainty of climate change projections, five global climate models and two representative concentration pathways (RCPs 2.6 and 8.5) were used. The ensemble-mean results showed that the global gross domestic product (GDP) loss in 2070–2095 due to cooling water insufficiency in the thermal power sector was −0.21% (−0.12%) in RCP8.5 (RCP2.6). Among the five regions, the largest GDP loss of −0.57% (−0.27%) was observed in the Middle East and Africa. Medium-scale losses of −0.18% (−0.12%) and −0.14% (−0.12%) were found in OECD90 (the member countries of the Organization for Economic Co-operation and Development as of 1990) and Eastern Europe and the Former Soviet Union, respectively. The smallest losses of −0.05% (−0.06%) and −0.09% (−0.08%) were found in Latin America and Asia, respectively. The economic impact of cooling water insufficiency was non-negligible and should be considered as one of the threats induced by climate change.

As a photo-catalytic titanium oxide film deposition process, thermal spray is hoped to be utilized practically on the condition that it is relatively easy to deposit anatase rich films. However, because of its high equipment and feedstock powder costs, it is very difficult to introduce thermal spray equipment into small companies. In this study, to develop a low cost thermal spray system, low power atmospheric suspension plasma spray equipment with titanium hydroxide suspension created by hydrolysis of titanium tetra iso butoxide using Ar, N2 as working gases. For avoiding sedimentation of the hydroxide particles in the suspension, mechanical milling of the suspension was conducted to create colloidal suspension before using it as feedstock. Moreover, an Ultrasonic wave container was used to keep the suspension particles moving while the spray process was conducted. After the film deposition, with As for the coating, anatase rich TiO2 film could be obtained. For characterization of the film, microstructure observation by optical microscope and X-ray diffraction was carried out. Consequently, by creation of colloidal suspension, deposition could be conducted without sedimentation of the hydroxide particle in the suspension during operation. Besides, it was proved the film had enough photo-catalytic property to decolor methylene-blue droplet

Na-magadiite exchanged with cetyl-trimethylammonium cations provided organophilic silicate materials that allowed the effective removal of the acidic dye "eosin". The organic cations were intercalated into the interlayer spacing of the layered silicate via an exchange reaction between the organic cations from their bromide salt and the solid Na-magadiite at room temperature. Different techniques were used to characterize the effect of the initial concentration of the surfactant on the structure of the organo-magadiites. The C, H, N analysis indicated that a maximum of organic cations of 1.03 mmol/g was achieved at initial concentrations higher than 0.25 mmol/g and was accompanied by an expansion of the basal spacing of 3.15 nm, with a tilted angle of 64.5° to the silicate layers. The conformation of the organic surfactants was probed using solid-state ¹³C, finding mainly the trans conformation similar to that of the starting cetyl trimethylammonium bromide salt (C16TMABr). Thermal gravimetric analysis was carried out to study the thermal stability of the resulting organo-magadiites. The intercalated surfactants started to decompose at 200 °C, with a mass loss percentage of 8 % to 25 %, depending on the initial loading of the surfactant, and was accompanied by a decrease of the basal spacing from 3.20 nm to 2.51 nm, as deduced from the in situ X-ray diffraction studies. At temperatures below 220 °C, an expansion of the basal spacing from 3.15 to 3.35 nm occurred. These materials were used as a removal agent for the anionic dye "eosin". The maximum amount of the dye removed was related to the organic cation content and to the initial concentration of eosin, with an improvement from 2.5 mg/g to 98 mg/g. This value decreased when the organo-magadiite was preheated at temperatures above 200 °C. The regeneration tests indicated that an 85 % removal efficiency was maintained after 6 cycles of use for the organo-magadiites.

In this paper, an icosahedral non – body centered model to simulate the periodic structure of homogeneous particulate composites, by predicting the particle arrangement, is presented. This model has yielded three different variations which correspond at three different deterministic particle configurations. In addition, the concept of boundary interphase between matrix and inclusions was taken into account. Thus, the influence of particle vicinity was examined in parallel with the interphase concept on the thermomechanical properties of the overall material. Next, by the use of this model the authors derived a closed – form expression to estimate the thermal conductivity of this type of composites. To test the validity of the model, the theoretical values arising from the proposed formula were compared with other theoretical predictions obtained from several accurate formulae found in the literature and an adequate accordance was observed.

Shale gas production is associated with significant usage of fresh water and discharge of wastewater. Consequently, there is a necessity to create the proper management strategies for water resources in shale gas production and to integrate conventional energy sources (e.g., shale gas) with renewables (e.g., solar energy). The objective of this study is to develop a design framework for integrating water and energy systems including multiple energy sources, cogeneration process, and desalination technologies in treating wastewater and providing fresh water for shale gas production. Solar energy is included to provide thermal power directly to a multi-effect distillation plant (MED) exclusively (to be more feasible economically) or indirect supply through a thermal energy storage system. Thus, MED is driven by direct or indirect solar energy, and excess or direct cogeneration process heat. The proposed thermal energy storage along with the fossil fuel boiler will allow for the dual-purpose system to operate at steady-state by managing the dynamic variability of solar energy. Additionally, electric production is considered to supply a reverse osmosis plant (RO) without connecting to the local electric grid. A multi-period mixed integer nonlinear program (MINLP) is developed and applied to discretize operation period to track the diurnal fluctuations of solar energy. The solution of the optimization program determines the optimal mix of solar energy, thermal storage, and fossil fuel to attain the maximum annual profit of the entire system. A case study is solved for water treatment and energy management for Eagle Ford Basin in Texas.

A simple fabrication method in the surface modification of electroosmotic silicon microchannel using thermal dry oxidation is presented. The surface modification is done by coating the silicon surface with a silicon dioxide (SiO₂) layer using thermal oxidation process. The process is aimed not only to improve the surface quality of the channel to be suitable for electroosmotic fluid transport but also to reduce the channel width using a simple technique. Initially, the parallel microchannel array with dimensions of 0.5 mm length and width ranging from 1.8 µm to 2 µm are created using plasma etching on the 2x2 cm <100> silicon substrate. The oxidation of silicon channel in a thermal chamber is then conducted to create the SiO₂ layer. The layer properties and the quality of the surface are analyzed using SEM and surface profiler, respectively. The results show that the maximum oxidation growth rate occurs in the first 4 hours of oxidation time and the rate decreases by time as the oxide layer becomes thicker. It is also found that the surface roughness is reduced with the increase of process temperature and oxide thickness. The scallop effect on the vertical wall due to plasma etching process also improved with the presence of the oxide layer. After the oxidation, the channel width is reduced by ~40%. The demonstrated method is suggested for the fabrication of a uniform channel cross section with high aspect ratio in sub-micro and nanometer scale that will be useful for the electroosmotic flow (EOF) manipulation of the biomedical fluid sample.

In this study, the efficiencies of flat-plate and U-tube solar collectors were investigated experimentally when an Al₂O₃ nanofluid was used as a working fluid and compared to those of solar collectors using water. The energy saving and CO₂ and SO₂ generated were calculated and compared to those of solar collectors using water. In addition, based on the experimental results, an economic analysis of the use of solar collectors in various countries was performed. As the concentration of the Al₂O₃ nanofluid increased, the performance of the solar collector improved. The highest efficiency for the solar collectors was shown at the concentration of 1.0 vol% with the nanoparticle size of 20 nm. The maximum efficiencies of the flat-plate and U-tube solar collectors using 1.0 vol%-Al₂O₃ nanofluid with 20-nm nanoparticles was 74.9% and 72.4%, respectively, when the heat loss parameter was zero. The efficiencies of the flat-plate and U-tube solar collectors using Al₂O₃ nanofluid were 14.8% and 10.7 higher, respectively, than those using water. When 50 EA flat-plate solar collectors were operated for one year using Al₂O₃ nanofluid, the coal use, generated CO₂, and generated SO₂ were 189.99 kg, 556.69 kg, and 2.03 kg less than those of solar collectors using water, respectively. In addition, the largest electricity cost reduction was in Germany.

In this paper, a geometric body-centered model to simulate the periodic structure of unidirectional fibrous composites is presented. To this end, three prescribed configurations are introduced to predict in a deterministic manner the arrangement of internal and neighboring fibers inside the matrix. Thus, three different representative volume elements (RVEs) are established. Furthermore, the concept of the interphase has been taken into account, stating that each individual fiber is encircled by a thin layer of variable thermomechanical properties. Next, these three unit cells are transformed in a unified manner to a coaxial multilayer cylinder model. This advanced model includes the influence of fiber contiguity in parallel with the interphase concept on the thermomechanical properties of the overall material. Then, by the use of this model, the authors propose explicit expressions to evaluate the longitudinal and transverse thermal conductivity of this type of composite. The theoretical predictions were compared with experimental results, as well as with theoretical values yielded by some reliable formulae derived from other workers, and a reasonable agreement was found.

Thermal-expandable microcapsules (TEMs) for water-based coatings were synthesized with co-polymer of Acrylonitrile (AN) - Methyl methacrylate (MMA) - Ethylhexyl acrylate (EHA) - Divinylbenzene (DVB) as shell and toluene-p-sulfonyl hydrazide as core by suspension polymerization method. It was found that the microcapsules with desirable thermal expansion property and good heat stability could be obtained with a shell monomers composition of 70% AN /20% MMA /9% EHA /1% DVB. When 2% styrene-maleic acid copolymer (SMC) as emulsifier and 3% poly (vinyl pyrrolidone) (PVP) as dispersing agent were used, well defined spherical and more uniform microcapsules could be prepared. It was also found that when the shell/core mass ratio was 3:1, an encapsulation efficiency of ca. 94.5% could be achieved. Beyond this ratio, the increase of encapsulation efficiency reached a plateau. The 100 μm thickness film of water-based coating containing 5% microcapsules could be expanded to the thickness of 450 μm after exposed at 150 °C for 2 minutes. TG analysis revealed the mass loss start temperature of coating increased by more than 30 °C when 5% microcapsules were added to water-based coatings, which demonstrated the flame-retardant function of the coatings.

Starting with a hypothetical geostrophic zonal current in an unbounded ocean, the investigation points out the response of this simple system to a thermal forcing, applied to the free surface and consistent with the maintenance of the geostrophic balance. The main result is the formation of a meridional component of the current, according to the Sverdrup relation, such that the full velocity vector rotates clockwise for heating and anticlockwise for cooling to adjust eventually in the initial zonal direction for large depths.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

Arsenic, an element of environmental impact, can be incorporated into jarosite–type compounds and remain stabilised within the structure under a wide range of environmental conditions. In this study, a sample of ammonium–arsenic jarosite was synthesised by precipitation in sulphate medium at controlled pH of 1.2–1.8. The behaviour of arsenic during the thermal and chemical decomposition of jarosite was analysed; the degradation in alkaline medium of jarosite was also studied. According to the results, the synthesised jarosite is composed of joined rhombohedral crystals, forming tightly spherical shaped particles, 37–54 μm size. The ammonium jarosite produced possessed a high arsenic concentration; its calculated stoichiometry being (NH₄)Fe_2.45[(SO₄)_1.80(AsO₄)_0.20][(OH)_4.15(H₂0)_1.85]. It was found that arsenic is stabilised in the jarosite structure; upon heating, it remains in residual solids above 700°C, whilst in alkaline medium an incongruent dissolution takes place, with the arsenic retained in the solid phase along with iron. These solids, when exposed to high temperatures (1200°C), transform into a type of iron oxide known as hematite, so with arsenic it is retained an iron compound forming a stable compound which withstands high temperatures.

High redshift blazars are among the most powerful objects in the Universe. Although they represent a significant fraction of the extragalactic hard X-ray sky, they are not commonly detected in gamma-rays. High redshift (z>2) objects represent <10 per cent of the AGN population observed by Fermi so far, and gamma-ray flaring activity from these sources is even more uncommon. The characterization of the radio-to-gamma-ray properties of high redshift blazars represents a powerful tool for the study of the energetics of such extreme objects and the Extragalactic Background Light. This contribution will present results of multi-band campaigns, from radio to gamma-rays, on PKS 0836+710, PKS 2149-306, and TXS 0536+145. The latter is the highest redshift detection of a flaring gamma-ray blazar so far. At the peaks of their respective flares these sources reached an apparent isotropic gamma-ray luminosity of about 10^50 erg/s, which is comparable with the luminosity observed from the most powerful blazars. The physical properties derived from the multi-wavelength observations of these sources are then compared with those shown by the high redshift population.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Historically, the evaluation and assessment of the clinical response to treatment for canine back pain is subjective and relies on owner and clinician assessment of pain. This study evaluated the use of sequential infrared thermal images as a measure of the response of canine patients with back pain to a prescribed series of photobiomodulation therapy (PBMT) treatments. Qualifying participants had histories of pain and dysfunction associated with spinal osteoarthritis or intervertebral disk disease, or of non-specific uni- or bilateral back pain along the paravertebral epaxial muscles. Each patient was initially thermally imaged prior to PBMT treatment and then received multiple PBMT treatments delivered to the appropriate spinal area on days 1, 2, 3, and 4. Participants were reimaged on day 7. Thermal images provided an objective measure of superficial temperature changes over the area of PBMT treatment of each patient after the PBMT regimen. The temperature correlated with statistically significant changes in Colorado State University Canine Chronic Pain Scale scoring (CPS) and owner assessment using the Canine Brief Pain Inventory (CBPI), which includes a Pain Severity Score (PSS) and Pain Interference Score (PIS). The correlation of objective thermal imaging data with more subjective outcome measures suggests thermal imaging may be a valuable additional tool in monitoring therapy outcome.

In this work, the Pumped Storage Unit (PSU) is proposed to be integrated with wind-thermal generation system owned by a company whose aim is to maximize its profit through optimal self-scheduling of its units by finding the best bidding strategy in day-ahead energy market. The mathematical formulation of the scenario based unit-commitment and coordinated trading problem is formulated as a stochastic mixed integer linear program. The formulation takes into account several uncertain parameters; such as the wind power generation, energy market prices, and imbalances up/down prices. The expected total profit obtained from energy trading with and without coordinating pumped storage system (PSS) with thermal-wind generation system were compared, and a significant improvement in profit resulted from coordination was observed. Furthermore, coordination between PSS and wind-thermal generation improve the conditional value at risk (CVaR) which monitors the biding risk level.

Poly(hydroxyalkanoates) (PHAs) are currently considered competent candidates to replace traditional plastics in several market sectors. However, commercial PHA grades exhibit unsatisfactory smell that can negatively affect the quality of the final product. The cause of this typical rancid odour is attributed to oxidized cell membrane glycolipids, coming from Gram negative production strains, which remain frequently attached to PHAs granules after extraction. The aim of this research is the development of customised PHA nano-biocomposites for industrial applications containing organo-modified nanoclays with high adsorption properties able to capture volatile compounds responsible of the displeasing fragrance in PHAs. To this end, a methodology for the detection and identification of the key volatiles released due to oxidative degradation of PHAs has been established using a headspace solid-phase microextraction technique. We report the development of nine nano-biocomposite materials based on three types of commercial PHA matrices loaded with three species of nanoclays which represent a different polar behaviour. It has been demonstrated that although the reached outcome effect depends on the volatile nature, natural sepiolite (T2) might result in the most versatile candidate for all PHA matrices selected.

Measurement of Globe temperature is essential for investigating thermal comfort in street canyon. Globe thermometer is the most common instrument used to measure globe temperature (GT), however its application in scale models is still uncertain and not thoroughly investigated as of today. Therefore, this study is explicitly conducted to investigate globe thermometer measurements and proposed an improvised customization of the globe thermometer size to enhance reliability in scale models. The experiments were carried out outdoors using a typical street canyon model (scale 1:100) with East-West street orientation. The experiment presented a comparison between a low solar reflective street canyon (albedo of 0.4) and a high solar reflective canyon (albedo of 0.6) in terms of surface temperatures, heat flux and globe temperature. Furthermore, this study also investigated the influence of solar orientation on the globe temperature using both experimental using scale models and microclimatic modelling using ENVI-met. It is observed that although the surface temperatures are lower with high solar reflective canyon compared to that with low solar reflective canyon, GT is higher in high reflective canyon during daytime, which could be due to combined effect of direct radiation and shortwave reflection. However, for hours after the sun set, GT becomes lower (up to 1°C) in the case of high reflective canyon compared to low reflective canyon.

Potassium-oxygen batteries (KOBs) are a promising energy storage technology with high theoretical en-ergy density, low overpotential and long cycle life. Cathode microstructure plays a significant role in the electrochemical performance of KOB. In this article, hierarchical porosity was introduced to commer-cially available carbon paper cathodes by the thermal pretreatment in air at different pretreatment times. This pretreatment modifies the properties, such as, surface area, defects, oxygen functional groups etc. and it has been found to enhance the discharge capacity and it result in reduction of dis-charge overpotentials.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

Utilizing NCEP/NCAR monthly reanalysis data alongside precipitation observations from 1936 monitoring stations across China spanning from 1966 to 2022, this study establishes a location index for the thermal low-pressure center situated over the Qinghai–Tibet Plateau. Temporal variations in the location index and summer (July) precipitation patterns in China were studied. Over the past six decades, thermal low-pressure centers have been predominantly positioned near 90°E and 32.5°N on the plateau, with their distribution extending from east to west rather than from south to north. The longitudinal and latitudinal position indices exhibit contrasting linear trends, with a positive trend observed during the 1970s and early 21st century and a negative trend in subsequent decades. Mutation analysis highlights pronounced weakening mutations occurring in 1981 and 1973, with the longitudinal index transitioning from an inter-annual cycle of approximately 6-8 years, while the latitudinal index displays quasi-cyclic oscillations of 5 and 8 and 12-14 years. Strong negative correlations are evident between the location indices and precipitation along the southeastern edge of the Qinghai–Tibet Plateau and in Southern China, contrasting with the positive correlations observed in the central-eastern plateau, northwest China, North China, and the Huang-Huai region. The influence of southerly airflow predominates over much of China east of the plateau, while northwest China experiences convergence between northerly and southerly airflow. Higher location indices correspond to weaker surface cold air masses and strengthened Western Pacific Subtropical and South Asian Highs south of the Yangtze River Basin, resulting in significantly reduced rainfall in the southern Yangtze River region and increased rainfall in northwest China.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

In Mexico viticulture represents the second source of employment in the agricultural area after the fruit and vegetable sector. In developed countries, remote sensing is widely used for vineyard monitoring, however, this tool is barely used in developing countries of Iberoamerica. In this re-search, our overall objective is to characterize two vineyards in the state of Queretaro (Mexico) using Sentinel-2 and meteorological data, specifically spectral and thermal indices. Results showed that spectral indices obtained from Sentinel-2 bands have characterized adequately the phenolog-ical evolution of the different varieties of the vineyards. The Modified Soil-Adjusted Vegetation Index (MSAVI) was adequately used to discriminate the first stages of vineyards, while the Nor-malized Difference Vegetation Index (NDVI) was useful to monitor vineyards during the rest stages of vineyards. Thermal indices have shown that the best grape varieties were those that can adapt to both cooler and warmer temperatures, have a reasonable ripening period, and can produce wines with balanced acidity and flavors. In conclusion, the combination of meteorological (including thermal indices) and remote sensing data (NDVI and MSAVI) provide information for choosing the suitable grape variety for this region.

In this study, seven mortar mixes were prepared by replacing natural sand by crumb rubber ,CR, (10%, 25%, 50%, 60%, 75% and 100%). The properties of mortars, both in their fresh and hardened states, were studied. Key characterisitcs, including density, water absorption coefficient, porosity, thermal conductivity, heat capacity, shrinkage/swelling, elastic modulus, compressive strength, flexure strength, fracture energy and performance after exposure to heat, were evaluated. The results obtained showed that as the CR fraction increased, density, initial setting time, and workability decreased but mortars with CR fractions ranged between 25% and 50% are lightweight and can be used for repairing as they fulfill satndards. It was observed that strengths and stiffness decreased with higher CR content while shrinkage increased for CR percentage higher than 60%. However, up to 50% of CR content the mortars obey to the standards for repair. Interestingly, incorporating up to 50% waste tires proved to improve comfort and thermal resistance without affecting thermal inertia. A slight increase in the mass loss is observed when mortars are exposed to high temperatures. Mortars containing CR between 25% and 50% can be classified as lightweight and thermally insulating mortars, suitable for repairing concrete structures in accordance with industry standards.

This review delves into the critical role of automation and sensor technologies in optimizing parameters for thermal treatments within electricity power generation. The demand for efficient and sustainable power generation has led to a significant reliance on thermal treatments in power plants. However, ensuring precise control over these treatments remains challenging, necessitating the integration of advanced automation and sensor systems. This paper evaluates the pivotal aspects of automation, emphasizing its capacity to streamline operations, enhance safety, and optimize energy efficiency in thermal treatment processes. Additionally, it highlights the indispensable role of sensors in monitoring and regulating crucial parameters such as temperature, pressure, and flow rates. These sensors enable real-time data acquisition, facilitating immediate adjustments to maintain optimal operating conditions and prevent system failures. It explores the recent technological advancements, including machine learning algorithms and IoT integration, which have revolutionized automation and sensor capabilities in thermal treatment control. Incorporating these innovations has significantly improved the precision and adaptability of control systems, resulting in heightened performance and reduced environmental impact. This review underscores the imperative nature of automation and sensor technologies in thermal treatments for electricity power generation, emphasizing their pivotal role in enhancing operational efficiency, ensuring reliability, and advancing sustainability in power generation processes.

In this study, Cu/Ni and Cu/Al multilayer thin films with individual layer thickness varying from 25 nm to 200 nm were deposited at room temperature and further annealed up to 300 ℃. The mechanical and microstructural properties of the multilayers were characterized by nanoindentation, x-ray diffraction, and scanning electron microscopy. Both systems exhibited an increase in hardness with increasing annealing temperature. However, the Cu/Ni system showed a gradual and moderate (up to 30%) hardness increase from room temperature to 300 ℃, while the Cu/Al system showed a sharp increase (~150%) between 125℃ and 200℃. This distinct strengthening behavior is attributed to solid solution formation in Cu/Ni and diffusion-activated intermetallic formation in Cu/Al.

To improve the adaptability of aerial reflective opto-mechanical structures to low-temperature environments, an optimized thermal control design is proposed. Firstly, the relationship be-tween conventional heating methods and axial/radial temperature differences of mirrors with different shapes is analyzed. Based on heat transfer analyses, it is pointed out that optimized thermal control design is necessary to ensure the temperature uniformity of the fused silica mirror and take into account the temperature level when working in low temperature environ-ments. A thermal control scheme based on temperature negative feedback variable power zone heating is proposed for the characteristics of aerial electro-optics systems. Using the thermal control scheme at low temperatures ensures that the average temperature of the mirror fluctu-ates slowly and slightly around 20℃. At the same time, the temperature differences within a mirror and between the primary mirror and the secondary mirror can be controlled within 5℃. Thereby, satisfactory image quality is obtained.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

Negative thermal quenching (NTQ) denotes that the integral emission spectral intensity of a given phosphor increases continuously with increasing temperature up to a certain elevated temperature. NTQ has been a subject of intensive investigation in recent years and a large number of phosphors were reportedly to have exhibited NTQ. In this paper, a collection of results in the archival literature about NTQ of specific phosphors are discussed from a macroscopic viewpoint in the following three aspects:1) Could NTQ of a given phosphor be reproducible?2) Could the associated data for a given phosphor exhibited NTQ be in line with the law of conservation of energy?3) Could NTQ of a given phosphor be demonstrated in a prototype WLED device? By analyzing typical cases based on common sense, it is hoped to increase the awareness for the issues with the papers reporting NTQ of the specific phosphors based on spectral intensity along with for the importance of keeping stability and consistency of the measurement conditions in temperature-dependent spectral intensity measurement which is a prerequisite for the validity of the measurement results.

The development of Al-Ni alloys with a controlled microstructure has had a great impact on the field of study of aluminum-based alloys. In the present research, the influence of thermal parameters on the grain structures resulting from the directional solidification process of Al-Ni alloys with different alloy content has been studied. It has also been evaluated how different structures and the distribution of second phases influence the corrosion behavior and microhardness of alloys. The columnar-to-equiaxed transition (CET) was observed to occur when the temperature gradient in the melt decreased to values between 1.3 to 2.9 ° C/cm. In addition, a small increase in the microhardness values was observed as a function of the Ni-content. When the Ni-content increase, the resistance to polarization decreases for samples with equiaxed grain structure, throughout the range of compositions studied. Furthermore, the equiaxed grain structure presents higher resistance to polarization values than the columnar grain zone, for alloys with a composition equal to or lower than the eutectic composition.

Jalapeño peppers (Capsicum annuum L.) are an important agricultural product worldwide. Despite its high demand in recent years, there are few studies on its production under adverse conditions caused by environmental phenomena. Crops in protected environments such as aeroponics offer greater control of these phenomena and enable efficient use of resources. However, it is necessary to validate the cultivation technique for which new technologies are being used. One of these is the analysis of images captured in the visible and near and far infrared spectrum which involves using non-invasive techniques in order to characterize the growth of a plant and diagnose if it presents any type of stress. This study presents the characterization of vegetative growth and fruiting of jalapeño pepper plants in an aeroponic system, where the root, leaf development parameters and fruits were measured in four jalapeño pepper crops through images of plants captured in the visible (VIS), near infrared (NIR) and far infrared (IR) spectrums. Four crops of thirty jalapeño pepper plants were sown to obtain a total of one hundred and twenty plants which were characterized in the different phases of growth and fruiting. Each of the four jalapeño pepper crops were monitored for sixty days in an aeroponic system in a greenhouse. The first crop was intended to carry out tests to establish the appropriate fertigation times, the next three crops were grown under favorable conditions. Algorithms were developed in Matlab to obtain, over ten image capture sessions, the morphometric and thermal parameters of the roots (perimeter, area, length and average temperature), plants (perimeter, area, height and average temperature), and fruiting. (yield and number of fruits). The statistical analysis was carried out using the ANOVA and Tukey tests considering a value of p ≤ 0.05. The results obtained indicate that there is no significant difference between the characterizations of the four crops. This statement is also supported by the visual analysis of the growth curves parameters of the four crops. In addition, the temperature inside the aeroponic system was contrasted with the ambient temperature and it was verified that the temperature to which the roots are exposed was in the range of 10°C – 20°C. The thermal analysis determined that a plant that presents water stress and is also exposed to high temperatures has an average leaf temperature of 3.7 to 5 °C above the optimal condition for the plant, while a plant with stress at normal temperatures was 1.3 °C higher than the plant without stress.

The article describes the use of microwave irradiation in the synthesis of bis(cyclo carbonate) compounds (BCC) in bulk (without solvent) from carbon dioxide capture using an epoxidized compound - a commercial epoxy resin, and compares this process to the conventional method. CO2 cycloaddition to epoxides is an ecological and efficient method for the formation of bis(cyclic carbonates). Moreover, the introduction of gas into the reaction mixture was carried out at atmospheric pressure with a controlled flow rate, which is advantageous from an economic point of view. Progressive structural changes and the presence of characteristic chemical groups were monitored using attenuated total reflectance infrared spectroscopy with Fourier transform. The obtained crude products were purified to obtain three fractions, which were subjected to detailed structural analysis using FT-IR and 13CNMR. The formation of the main product with two cyclic carbonates was confirmed. The presence of monomers, dimers and trimers in individual fractions as well as their thermal stability were determined, and the molecular masses in individual fractions were determined using gel permeation chromatography (GPC).

The paper presents research results on biocomposites made from a combination of extruded apple pomace (EAP) and potato starch (SP). The products were manufactured by hot pressing using a hydraulic press with a mold for producing samples. The prepared biocomposites were subjected to strength tests, surface wettability was determined and color analysis was carried out. Thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR) and cross section observed in Scanning electron microscope (SEM) were also performed. The obtained test results showed that the combination of apple pomace (EAP) and starch (SP) enabled the production of compact bicomposite materials. At the same time, it was found that each increase in the share of starch in the mixture for producing biocomposites increased the strength parameters of the obtained materials. With the highest share of starch in the mixture, 40%, and a raw material moisture content of 14%, the material had the best strength parameters and was even characterized by hydrophobic properties. It was also found that materials with a high content of starch are characterized by increased temperature resistance. Analysis of SEM microscopic photos showed well-glued particles of apple pomace, pectin, gelatinized starch and a smooth external structure of the samples. Research and analyzes have shown that apple pomace reinforced only with the addition of starch can be a promising raw material for the production of simple, biodegradable biocomposite materials.

High-performance insulation and airtight building envelopes are the two most important factors to optimize the building energy efficiency and thermal performance. However, thermal performance of building envelopes can be significantly affected by thermal bridging. Thermal bridges can take place at different locations of the building envelope, causing added transmission losses, increasing heat flow, lower inner surface temperatures. Thermal bridges are regarded in all national regulations for new buildings of all states of European Union (EU) but there are no specifications assessing balconies to wall junctions and the impact on the building thermal performance is not well regulated. In this paper, balcony to wall thermal bridge assessment using infrared thermography is highlighted. The originality is that, infrared thermography, has been applied to a real living latest building in the north east of France showing that there is noncompliance in the national regulations as some exigencies are not met. Thermography of thermal break windows and window doors has also revealed air leakage. The goal, is to illustrate that thermal imaging is a means of quality assurance to new building specifications and should include a clause specifying quality assurance procedure for balconies junction in national building regulations for all states if the EU.

For the eutectic molten PbBi alloy, we tested the additive properties of density, sound velocity, compressibility and dynamic viscosity of this alloy in the temperature range 600 – 1200 K. All these values can be represented as a mass-weighted sum of the corresponding values of pure lead and bismuth in the temperature range 600 – 1000 K within the limit of experimental errors. In the temperature range 800 – 900 K, we found that interatomic forces in the eutectic increase with temperature, which is caused by a decrease in the size of accumulations of atoms, clusters, of melt. A decrease in the size of clusters is accompanied by an increase in bonds between atoms within the clusters, which make them more stable.

For a fiber optic gyroscope, thermal deformation of the fiber coil can introduce additional ther-mal-induced phase errors, commonly referred to as thermal errors. Thermal error compensation techniques are effective means of addressing this issue. The principle behind these techniques involves real-time sensing of thermal errors and correcting them within the output signal. Since it is challenging to directly separate thermal errors from the output signal of the fiber optic gyro-scope, it is necessary to predict thermal errors based on temperature. To establish a mathematical model between temperature and thermal errors, this paper measured synchronized data of phase errors and angular velocity for the fiber coil under different temperature conditions and aimed to model it using data-driven methods. Due to the difficulty of conducting tests and the limited number of data samples, an algorithm called TD-model modeling is proposed to address the issue of overfitting, which can reduce the model's generalization ability. First, a theoretical analysis of the phase errors caused by thermal deformation of the fiber coil is performed. Subsequently, the critical parameters, such as the thermal expansion coefficient, are determined, and a theoretical model is established. Finally, the theoretical analysis model is incorporated as a regularization term and combined with the test data to jointly participate in the regression of model coefficients. Through experimental comparative analysis, it is shown that, relative to ordinary regression models, the TD-model effectively mitigates overfitting caused by the limited number of samples, leading to a 58% improvement in predictive accuracy.

Thermal analysis of a hypereutectic Al-Si alloy used for an automotive part was carried out in this research work. Solidification characteristics are recognized from the Temperature-time curve and its corresponding derivatives. This analysis was successfully used in a simulation software program with the aim of improving the resultant simulation accuracy. In this study, different types of molds, with and without cooling systems, were designed and used. The melt present in the furnaces of the factory was used to simulate the casting process. The effect of different cooling rates (1.2ºC/s, 2ºC/s, 2.3ºC/s and 2.9ºC/s) on the solidification parameters have been investigated. Differences in the resultant microstructure between wall and center of the molds have been analyzed and have been related to the T-t curve. Finally, the experimental results clearly indicate that the water-cooling rate of the molds and the melt temperature directly affects the solidification process as well as the final microstructure.

Understanding the thermal cracks of rock caused by high temperature is of great help to the development of underground engineering, such as geothermal mining, underground coal gasification. Although there has been many study on thermal cracking, it is not systematic and in-depth enough. In order to deeply study the thermal crack mechanism of rock, this paper conducted thermal cracking experiments on granite at different temperatures and heating/cooling paths, and qualitative and quantitative analysis was conducted on the crack initiation characteristics, propagation paths, and crack network morphology of rock thermal crack under different test conditions. The thermal crack mechanism was also analyzed from the perspectives of mineral petrology, fracture mechanics, thermodynamics, and other aspects. The research results show that there are two obvious mutation points in the study temperature range for samples with fast cooling paths (SF path: slow heating and fast cooling; FF path: fast heating and fast cooling), around 200-300 ℃ and 600 ℃, respectively, while for samples with slow cooling paths (SS path: slow heating and slow cooling; FS path: fast heating and slow cooling), there is only one mutation point around 600 ℃. The initiation positions of thermal cracking under all temperature paths are relatively similar, with intergranular crack located between particles at the edge of the sample or intercrystalline crack in the middle of feldspar or quartz aggregates. The initiation temperature of SF and FF path specimens is relatively low compared to SS and FS path specimens, and the number and size of cracks is small. The crack network structure formed by the SF path is the most complex, with the largest crack ratio and cumulative crack length; The crack network structure formed by the FF path is relatively complex, with a larger main crack size but relatively fewer secondary cracks; The FS and SS paths do not form a complex network with good connectivity. The process of thermal crack development can be divided into three stages: the development of small cracks, the joint development of main cracks and small cracks, and the connection of cracks into a network structure. The mechanism of thermal crack propagation is that the expansion and thermal conductivity between different crystals are different. The thermal stress caused by temperature gradient and the tension or shear stress caused by the inconsistent deformation of crystals form stress concentration in weak areas such as particles boundary, cleavage, and original cracks. Firstly, it causes some crystals with smaller strength or less rounded shape to crack, and when the combined stress is large, the cracks will gradually expand along the existing fine cracks. This also explains that the most main cracks of the SF and FF path specimens mainly surround some large mineral aggregates or between particles.

Medium-deep Borehole Heat exchanger (MBHE) has been widely paid attention for building heating. In order to avoid the thermal interference of adjacent MBHEs, temperature distribution characteristics of medium-deep rock-soil was investigated in this work. The evolution on maximum rock-soil thermal affected radius (MTAR) in full life cycle was further analyzed. The results showed that the rock-soil thermal affected area (RTAA) continuously expands in both radial and vertical directions during a heating season. Several factors of thermal extraction load, fluid velocity, geothermal gradient and pipe length have main impacts on the RTAA in vertical direction. Rock-soil thermal conductivity affects the RTAA in both radial and vertical directions. In non-heating season, temperature difference of rock-soil in radial direction dominates the temperature recovery in the first year while geothermal flow nearly dominates temperature recovery after 20 years. The thermal affected radius (TAR) in the 30 th year could be determined as an effective MTAR in full life cycle. In order to decrease installed distance of adjacent MBHEs, a new well layout form by deflecting borehole was proposed. The recommended deflection angle is equal to or larger than 4 times TAR angle. This work provides scientific reference for promoting application of multiple MBHE arrays.

Graphene is a two-dimensional nanostructured material with intrinsic properties that show promising performance in various applications, including electronics, renewable energy, medicine, mechanical enforcement and others. This study reports a bottom-up approach for the conversion of cyclohexane into graphene nanoflakes, which were then deposited onto fiberglass using a non-thermal generator. The composite was characterized using transmission electron microscopy, which revealed the formation of stacked few-layer graphene with a partially disordered structure and a d-spacing of 0.358 nm between the layers. X-ray diffraction confirmed the observations from the TEM images. SEM images showed the agglomeration of carbonaceous material onto the fiberglass, which experienced some delamination due to the synthesis method. Raman spectroscopy indicated that the obtained graphene exhibited a predominance of defects in its structure. Additionally, Atomic Force Microscopy (AFM) analyses revealed the formation of graphene layers with varying levels of porosity.

Thermal safety of lithium-ion traction batteries is a highly concerned issue in the field of electric transportation. The large amount of gas emission during the thermal runaway process of batteries has highly safety hazards such as fire and explosion. Quantitative analysis of emission is one of the important challenges for testing and evaluating battery safety. Focus on quantifying the gas emission through large-scale thermal propagation in battery modules and packs, based on the idea of cell result multiplication, this article conducts thermal runaway emission analysis on single cell and modules, and compares the behavior of thermal runaway and gas emission of the cell and module from the aspects of temperature, pressure, gas composition and battery morphology. The feasibility of the cell result multiplication method was verified from the perspective of experimental data.

No system nor standardized analytical procedures at commercial laboratories exist to facilitate and accurately measure potential viable virus contamination in feed ingredients and complete feeds globally. As a result, there is high uncertainty of the extent of swine virus contamination in global feed supply chains. Many knowledge gaps need to be addressed to improve our ability to prevent virus contamination and transmission in swine feed. This review summarizes the current state of knowledge involving: 1) the need for biosecurity protocols to identify production, processing, storage, and transportation conditions that may cause virus contamination of feed ingredients and complete feed, 2) challenges of measuring virus inactivation, 3) virus survival in feed ingredients during transportation and storage, 4) minimum infectious doses, 5) differences between using a Food Safety Objective versus a Performance Objective as potential approaches for risk assessment in swine feed, 6) swine virus inactivation from thermal and irradiation processes, and chemical mitigants in feed ingredients and complete feed, 7) efficacy of virus decontamination strategies in feed mills, 9) benefits of functional ingredients, nutrients, and commercial feed additives in pig diets during a viral health challenge, and 10) considerations for improved risk assessment models of virus contamination in feed supply chains.

This study presents an experimental investigation of the convective drying process of ginger rhizomes (Zingiber officinale). It analyses the effect of moisture content on the thermal properties of dried ginger rhizomes. Drying experiments were conducted under controlled conditions to establish the relationship between moisture content and thermal conductivity. The drying kinetics were examined to provide insights into the drying behaviour of ginger rhizomes and the influence of moisture content on their thermal properties. The results demonstrated a significant impact of initial moisture content and convective drying conditions on the drying process. As drying progressed, the moisture content decreased, leading to a reduction in thermal conductivity. It was observed that drying under convective drying takes 24 hours compared to open sun drying at nine days and solar tunnel drying at eight days. The drying temperature of 60°C was considered optimum. The results show that dried ginger at an absolute moisture content of 6.63% (wb) with a thermal conductivity of 0.0553W/m. K for unblanched ginger, 9.04% (wb) with thermal conductivity of 0.0516W/m. K for blanched ginger, 8.56% (wb) moisture content with a thermal conductivity of 0.0483W/m. K for peeled ginger and 5.98% moisture content with a thermal conductivity of 0.0460W/m. K for unpeeled ginger would be ideal for making powdered ginger rhizomes. These findings have practical implications for the food industry, as they can aid in designing and improving drying processes for ginger rhizomes and similar agricultural products. By understanding the relationship between moisture content and thermal properties, more efficient drying strategies can be developed to minimise energy consumption and maintain the quality of the dried product.

The Macroscopic Mechanical Equilibrium Condition can be shown to be the physical origin of the Equation of State of any material system, then can describe all thermodynamic quasi-equilibrium processes caused by the change of the external temperature and/or mechanical environment. If it cannot be satisfied, the system would be broken.

This paper describes methods for evaluating the thermal properties of textile materials, clothing composites, and clothing using an integrated measurement system that includes a hot plate, a multi-purpose differential conductometer, a thermal manikin, a temperature gradient measurement device, and a device for measuring the physiological parameters of the human body during the exact evaluation of garment thermal comfort. In practice, measurements were taken on four types of materials widely used in the production of conventional and protective clothing. The measurements were carried out using a hot plate and a multi-purpose differential conductometer, determining the thermal resistances of the material in its uncompressed form and a force that was ten times greater than that needed to determine its thickness. Using a hot plate and a multi-purpose differential conductometer, thermal resistances of textile materials were assessed at different levels of material compression. On hot plates, both conduction and convection had an impact on thermal resistance, but in multi-purpose differential conductometer, only conduction did. Moreover, the reduction of thermal resistance was observed while compressing textile materials.

A recently identified broiler myopathy known as wooden breast (WB) is predominantly found in the pectoralis major muscle of fast-growing broiler hybrids and is causing significant losses to the poultry industry. The aim of this study was to investigate the effects of WB syndrome on raw meat texture, purge loss and thermal properties of intramuscular connective tissue of pectoralis major muscle in the early post-mortem period. Results showed that WB muscles at 1d postmortem was associated with significantly increased stiffness and significantly increased purge loss compared to normal muscles (NB). However, at 3d postmortem, these parameters did not differ between the two groups. Insoluble and total collagen content was significantly higher in WB muscles compared to NB muscles, and the extractability of intramuscular connective tissue (IMCT) was also higher and remained stable in the early postmortem period. These were coincided with significantly lower protein content in the sarcoplasmic protein fraction and myofibrillar protein fraction of WB muscles compared to NB muscles (P < 0.05). The IMCT of these two groups showed different thermal properties, as the enthalpy of denaturation (ΔH) was significantly lower in WB muscles compared to NB muscles. The WB syndrome had a great effect on the texture and connective tissue properties of the meat compared to normal muscle, with a tendency for having a lower water holding capacity and higher raw meat hardness

Brassica vegetables has demonstrated many health benefits over the years due to its composition of phenolic, flavonoid, and glucosinolate content. However, these bioactive molecules can be easily depleted during gastronomic operations. Therefore, a sustainable method which improves the phenolic content and antioxidant activity is required at large for the processors and consumers. Thermal processing has demonstrated as a method to improve the phenolic content and antioxidant status of Brassica vegetables. In the current study four different thermal processing methods, including freeze drying, sauteing, steam and air frying, were employed for five different Brassica vegetables, including kale, broccoli sprout, brussels sprout, red cabbage, and green cabbage. Total phenolic content (TPC), total flavonoid content (TFC), and antioxidant activities were assessed using radical scavenging activity (DPPH and ABTS•+), reducing power (FRAP), and chelating ability of the metal ions. Among tested, air frying at 160oC for 10 minutes showed the highest TPC, TFC, and antioxidant activity of the Brassica vegetables, while sautéing showed the lowest. Steam treatment was preferred over the freeze-drying treatment. Within the vegetables tested, both kale and broccoli sprout contained higher antioxidants properties in most processing treatment employed. Results also indicated that there is a strong correlation between TPC, TFC, and the antioxidant activity (p<0.05). This study indicates that air frying could be a choice of sustainable thermal processing method for improving biomolecules for Brassica vegetables.

The results of the study of the influence of the size of cylindrical samples of A5N aluminum on the time and rate of their cooling are presented. According to experimental data, the temperature dependence of the heat transfer coefficient for pure metals is calculated. It revealed that the process of cooling of the aluminium and its alloys has a relaxation behavior. It has found that the main mechanisms of natural air cooling are convection heat transfer and radiation. The characteristic cooling time due to radiation is less than due to convection. The contribution of thermal radiation is noticeable at high temperatures. It was found that the characteristic times of cooling due to radiation and convection increase with increase in volume to area ratio of the sample.

The effects of post-treatment temperature-based methods on 1D single PLA filaments after FFF have been studied. This lets to decouple the variables related to the 3D structure (layer height, raster angle, infill density, and others) from the variables solely related to the material (molecular weight, molecular orientation, crystallinity, and others). PLA 1D filaments have been aged at 20, 39, 42, 51, 65, 75 and 80 ºC in a water-bath-inspired process in which the hydrolytic degradation of the PLA has been minimised for the ageing temperatures of interest. The evolution of the thermal and mechanical properties of the PLA filaments at different temperatures was recorded. Differential scanning calorimetry (DSC) was used to evaluate thermal and physical properties, in which the glass transition, enthalpic relaxation, crystallisation and melting reactions were analysed. Tensile tests were performed to evaluate the tensile strength and elastic modulus. The flow-induced molecular orientation, the degradation, the logistic fitting and the so-called summer effect –stabilisation of properties at higher temperatures– are discussed for assessing the safeness of accelerating ageing.

Biomass burning is an important and changing component of the global and hemispheric carbon cycles. Boreal forest fires in Russia and Canada are significant sources of greenhouse gases carbon dioxide (CO2) and methane (CH4). The influence of carbon monoxide (CO) on the greenhouse effect is practically absent: its main absorption bands of 4.6 and 2.3 μm are far away from the climatically important spectral regions. Meanwhile, CO concentrations in fire plumes are closely related to CO2 and CH4 emissions from fires. On the other hand, satellite measurements of CO are much simpler than those for the aforementioned gases. The Atmospheric Infrared Sounder (AIRS) provides a satellite-based CO data set since October, 2002 up to now. This communication presents estimates of CO emissions from biomass burning north of 30° N using a simple two-box mass-balance model. These results correlate closely with independently estimated CO emissions from the GFED4 bottom-up data base. Both ones reported record high emissions in 2021 throughout two decades, double the annual emissions comparing to the previous years. There have been two years with extremely high emissions (2003 and 2021), but for the rest of data upward trend with a rate of 3.6 ± 2.2 Tg CO yr-2 (4.8 ± 2.7% yr-1), was found. A similar rate of CO emission follows from the GFED4 data.

Biomass burning is an important and changing component of the global and hemispheric carbon cycles. In particular, boreal forest fires in Russia and Canada are important sources of greenhouse gases carbon dioxide (CO2) and methane (CH4). The influence of carbon monoxide (CO) on the climate is insignificant: its main absorption bands of 4.6 and 2.3 μm are far away from the climatically important regions of the spectrum. Meanwhile, CO concentrations in fire plumes are closely related to CO2 and CH4 emissions from fires. On the other hand, satellite measurements of CO are much simpler than those for the aforementioned gases. The Atmospheric Infrared Sounder (AIRS) provides a long satellite-based CO data set. This article presents estimates of CO emissions from biomass burning north of 30° N using a simple two-box model. These results correlate closely with independently estimated CO emissions from the GFED4 bottom-up data base. Both ones reported record high emissions in 2021 throughout two decades, double the annual emissions comparing to the previous a few years. There have been several years with extreme emissions, but for the rest of data upward trend with a rate of 3.7 ± 2.3 Tg CO yr-2 (4.4 ± 2.8% per year), was found.

Heating has been recently used as an alternative application to electrical stimulation to modulate excitability and to induce neuritogenesis and the expression of neuronal markers, but a long-term functional differentiation has not been described so far. Here we present the results obtained by a new approach for scalable thermal stimulation on the behavior of a model of dorsal root ganglion neurons, the F-11 cell line. Initially, we performed experiments of bulk stimulation in incubator for different time intervals and temperatures, and significant differences in neurite elongation and in electrophysiological properties were observed in cultures exposed at 41,5°C for 30 minutes. Thus, we exposed the cultures to the same temperature increase by irradiating, with a near infrared laser, a disc of Prussian Blue nanoparticles and poly-vinyl alcohol, that we stuck on the outer surface of the petri dish. In irradiated cells neurites were significantly longer and the electrophysiological properties (action potential firing frequency and spontaneous activity) were significantly increased compared to the control. These results suggest that a targeted thermal stimulation could be a promising technique to induce differentiation and support the future application of this method as a strategy to modify neuronal behavior in vivo.

In Europe, the recent application of regulations oriented to zero-energy buildings and climate neutrality in 2050 has led to a reduction in energy consumption for heating and cooling in the construction sector. The thermal insulation of the building envelope plays a key role in this process and the requirements about the maximum allowable thermal transmittance are defined by country-specific guidelines. Typically, high insulation values provide low energy consumption for heating, however, they may paradoxically imply the risk of overheating in summer period and thus negatively affect the overall performance of the building. In addition, the embodied energy and related emissions caused by the manufacturing and transportation processes of thermal insulation cannot be further neglected in the evaluation of the best optimal solution. Therefore, this paper aims to evaluate the influence in terms of embodied and operational energy of various walls’ thermal insulation thicknesses on residential buildings in Europe. To this end, the EnergyPlus engine was used for the energy simulation within Ladybug &amp; Honeybee tools, by parametrically conducting multiple iterations; 53 variations of external wall U-value, considering high and low thermal mass scenarios, were simulated for 100 reference cities of the European context, using a representative multifamily building as a reference. The results demonstrate that massive walls generally perform better than lightweight structures and, of course, the best solution in terms of energy varies according to each climate. The optimal values are graphically reported on the map of Europe according to specific climatic features, providing a guidance for new constructions and building retrofit.

In this research, Cellulose Nanofibers (NFC) modified with a eutectic of lauric acid (LA) was prepared as a new form-stable phase change material (NFC-LA). Thermal properties of this composite were investigated by Differential Scanning Calorimetry (DSC). The results revealed that the melting temperature and latent heat of NFC/LA were 21.56 °C and 88.5 J/g, respectively; and the super cooling degree for the NFC-LA composite decreased to 13.99 °C when compared to 20.28 °C of the pure lauric acid. Natural clay was purified and modified with Cetyltrimethyl ammonium bromide (CTAB) to prepare organoclay. Through FTIR spectra, we have confirmed that the clay was successfully modified. The PCM-composite was then added to the organoclay to obtain a new composite denoted NFC-LA-OC. this latter was added to cement and was investigated as a reinforcement material in cement mortars for thermal energy storage application. The prepared material can both solve the leakage problem associated to the phase change material, and reduce or even avoid the use of heating and air conditioning systems, which are energy-intensive systems, and therefore reduce energy consumption.

Over the years, leaked fluids from the aircraft caused severe deterioration of the airfield pavement. The combined effect of hot exhaust from the auxiliary power unit of military aircraft and spilt aviation oils caused rapid pavement spalling. If the disintegrated concreted pieces caused by spalling is sucked into the jet engine, it may cause catastrophic damage to the aircraft engine or physical injury to maintenance crews. This study investigates the effectiveness of incorporating hybrid fibres into ordinary concrete to improve the residual mechanical and thermal properties to prevent spalling damage of pavement. Three fibre reinforced concrete samples made with micro steel fibre and polyvinyl alcohol fibre with a fibre content of zero, 0.3%, 0.5% and 0.7% by volume fraction. These samples were exposed to recurring high temperature and aviation oils. Tests were conducted to measure the effects of repeated exposure on the concrete's mechanical, thermal and chemical characteristics. The results showed that polyvinyl alcohol fibre reinforced concrete suffered a significant loss of thermal properties and residual mechanical strength than the micro steel fibre reinforced concrete. However, hybrid fibre reinforced concrete performed better in retaining higher residual properties, and no spalling of concrete was observed.

The paper is focused on numerical modeling of multi-strand cable lines placed in free air. Modeling is carried out within the framework of the so-called multi-physics approach using commercial software. The paper describes in detail the steps undertaken to develop realistic, reliable numerical models of power engineering cables, taking into account their geometries and heat exchange conditions. The results might be of interest to the designers of multi-strand cable systems.

Black poplar (Populus nigra L.) was thermally modified in nitrogen atmosphere. Treatment in nitrogen atmosphere can improve the dimensional stability of black poplar. The effects of the modification process on poplar wood were evaluated for temperatures: 160 °C, 190 °C, and 220 °C applied for 2 h; and 160 °C and 190 °C for 6 h. The percentual impact of temperature and time of modification on the properties of modified wood was analysed. The study permitted to identify correlations between the chemical composition and selected physical properties of thermally modified poplar wood. The dimensional stability of poplar wood improves after thermal modification in nitrogen. The higher the temperature of modification, the lower the equilibrium moisture content (EMC) of black poplar. At the temperature of 220 °C, EMC was two times lower than the EMC of non-modified black poplar. It is also possible to reduce the dimensional changes of wood two-fold (at the modification temperature of 220 °C), both in radial and tangential directions, independently of the acclimatisation conditions (from 34% to 98% RH). Similar correlations have been found for wood that has been soaked in water. Higher modification temperatures and longer processing times contributed to a lower swelling anisotropy (SA).

(1) Background: The aim of the present study was to evaluate the effect of different types of warm-ups on the strength and skin temperature of Paralympic powerlifting athletes; (2) Methods: The participants were 15 male Paralympic powerlifting athletes. It was analyzed the effects of three different types of warm-up (without warm-up (WW), traditional warm-up (TW), or stretching warm-up (SW)) on static and dynamic strength tests as well as in the skin temperature, which was monitored by thermal imaging; (3) Results: show no differences in the dynamic and static indicators of the force in relation to the different types of warm-up. No significant differences were found in relation to the Peak Torque (p = 0.055, F=4.560, η2p= 0.246 medium effect), and 1-Repetition Maximum (p = 0.139, F=3.191, η2p = 0.186, medium effect) between the different types of warm-up. In the thermographic analysis, there was a significant difference only in the Pectoral muscle clavicular portion between the TW (33.04 ± 0.71ºC) and the WW (32.51 ± 0.74ºC) (p = 0.038). The TW method also presented slightly higher values than the SW and WW in the Pectoral Muscles Sternal portion and in the Deltoid anterior portion, but with p-value &gt; 0.05; (4) Conclusions: that the types of warm-up studied do not seem to interfere with the performance of Paralympic Powerlifting athletes. However, the thermal images showed that traditional warm-up best meets the objectives expected for this preparation phase.

One-dimensional chain of core-shell pairs connected by ideal springs enables design of the metamaterial demonstrating the negative effective density and negative specific thermal capacity. We assume that the molar thermal capacity of the reported metamaterial is governed by the Dulong-Petit law in its high temperature limit. The specific thermal capacity depends of the density of the metamaterial; thus, it is expected to be negative, when the effective density of the chain is negative. The range of the frequencies enabling the effect of the negative thermal capacity is established. Dependence of the effective thermal capacity on the exciting frequency for various core/shell mass ratios is elucidated. The effective thermal capacity becomes negative in the vicinity of the local resonance frequency ω0 in the situation when the frequency ω approaches ω0 from above. The effect of the negative effective thermal capacity is expected in metals in the vicinity of the plasma frequency.

The purpose of this study was to develop a mathematical model for non-contacting face seals to analyze how their performance is affected by thermoelastic phenomena. The model was used to solve thermal conductivity and thermoelasticity problems. The primary goal was to calculate the values of thermal deformations of the sealing rings in a non-contacting face seal with a flexibly mounted rotor (FMR) for a turbomachine. The model assumes conversion of mechanical energy into heat in the fluid film. The heat flux generated in the fluid film is transferred first to the sealing rings and then to the fluid surrounding them. An asymmetric distribution of temperature within the sealing rings leads to the occurrence of thermal stresses and, consequently, a change in the rings geometry. The model is solved analytically. The distributions of temperature fields for the sealing rings in the cross-sections are calculated using the Fourier-Bessel series as a superficial function of two variables (r,z). The thermoelasticity problems described by the Navier equations are solved by applying the Boussinesq harmonic functions and Goodier’s thermoelastic displacement potential function. The proposed method involves solving various theoretical and practical problems of thermoelasticity in FMR-type non-contacting face seals. The calculated thermal deformations of the sealing rings are used to determine the most important seal performance parameters such as the leakage rate and power loss.

A probe of a patient, seeking help in an emergency ward of a French hospital in late December 2019 because of Influenza like symptoms, was retrospectively tested positive to COVID-19. Despite the early appearance of the virus in Europe, the prevalence and virulence appeared to be low for several weeks, before the spread and severity of symptoms increased exponentially, yet with marked spatial and temporal differences. Here, we compare the possible linkages between peaks of fine particulate matter (PM2.5) and the sudden, explosive increase of hospitalizations and mortality rates in the Swiss Canton of Ticino, and the Greater Paris and London regions. We also discuss the influence of Saharan dust intrusions on the COVID-19 outbreak observed in early 2020 on the Canary Islands. We find that high PM2.5 concentrations – possibly favored by air temperature inversions or Saharan dust intrusions – are not only modulating but even more so boosting severe outbreaks of COVID-19. We conclude that the overburdening of the health services and hospitals as well as the high over-mortality observed in various regions of Europe in spring 2020 can be linked to peaks of PM2.5 and likely particular weather situations that have favored the spread and enhanced the virulence of the virus. In the future, we recommend to monitor not only the prevalence of the virus, but also to consider the occurrence of weather situations that can lead to sudden, very explosive COVID-19 outbreaks.

In this study, fibers were extracted from different parts of the okra plant (Abelmoschus esculentus) via water- and dew-retting methods. The fibers were subjected to physical and thermal analyses. The fibers obtained from the upper part of the okra plant show higher breaking strength and lower linear density. Fibers obtained via water-retting exhibited higher breaking strength, elongation at break rates, and lower linear density values. The paper also presents the results of thermogravimetric analysis of the okra fibers. Tests were carried out in oxygen and inert gas atmospheres. The temperature range of the main thermal decomposition stage was in the 275–400°C for range thermo-oxidation and 300–425°C for pyrolysis investigation. Slight differences were found in the thermal resistances of the tested fibers, which was confirmed by an analysis using the alpha s- alpha r methodology. The calculated activation energy values show a large-spread range.

Thermal-based actuators are known for generating large force and displacement strokes at mesoscale (millimeter) regime. In particular, two-phase thermal actuators are found to benefit from the scaling laws of physics at mesoscale to offer large force and displacement strokes; but they have low thermal efficiencies. As an alternative, a combustion-based thermal actuator is proposed and its performance is studied in both open and closed cycle operations. Through a physics-based lumped-parameter model, we investigate the behavior and performance of the actuator using a spring-mass-damper analogy and taking an air standard cycle approach. Three observations are reported: (1) the mesoscale actuator can generate peak forces of up to 400 N and displacement strokes of about 16 cm suitable for practical applications; (2) an increase in heat input to the actuator results in increasing the thermal efficiency of the actuator for both open and closed cycles; and (3) for a specific heat input, both the open and closed cycle operations respond differently \textemdash different stroke lengths, peak pressures, and thermal efficiencies.

The NCO functional group of 3-isocyanatoproply triethoxysilane (IPTS) and the OH functional group of DOPO-BQ were used to conduct an addition reaction. Following completion of the reaction, triglycidyl isocyanurate (TGIC) was introduced to conduct a ring-opening reaction. Subsequently, a sol-gel method was used to take place a hydrolysis- condensation reaction on TGIC-IPTS-DOPO-BQ to form a hyperbranched nitrogen–phosphorous–silicon (HBNPSi) flame retardant. This flame retardant was incorporated into a polyurethane (PU) matrix to prepare a hybrid material. Fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), limiting oxygen index (LOI), UV-VIS spectrophotometry, and Raman analysis were conducted to structure characterization and analyzed transparency, thermal stability, flame retardancy, and residual char to understand the flame retardant mechanism of prepared hybrid materials. After the flame retardant was added, the maximum degradation rate decreased from −36 wt%/min to −17 wt%/min, the integral procedure decomposition temperature (IPDT) increased from 348 ℃ to 488 ℃, and the char yield increased from 0.7 to 8.1 wt%. The aforementioned results verified that thermal stability of PU can be improved after adding HBNPSi. The LOI analysis indicated that the pristine PU was flammable because the LOI of pristine PU was only 19. When the content of added HBNPSi was 40%, the LOI value was 26; thus the PU hybrid became nonflammable.

Polydimethylsiloxane with hydroxy groups was functionalized to form functionalized polydimethylsiloxane, which subsequently underwent an addition reaction with isophorone diisocyanate to form the prepolymer. Next, 3-aminopropyltriethoxysilane (APTS) reacted with 3-glycidoxypropyltrimethoxysilane (GPTS) to produce bridged polysilsesquioxanes, and the sol–gel technology was employed to form hyperbranched polysiloxane nanoparticles with hydroxy groups, which was used as the additive. The hyperbranched polysiloxane and the prepolymer containing NCO functional groups then underwent an addition reaction to produce the hybrid materials. Fourier-transform infrared spectroscopy and 29Si nuclear magnetic resonance were used to characterize the structure of the polyurethane hybrid. Regarding thermal stability, after the hyperbranched polysiloxane nanoparticles was introduced, the integral procedural decomposition temperature increased from 348 ºC for polyurethane matrix to 859 ºC for the hybrid material. The results revealed that the thermal stability of the hybrid material substantially increased by approximately 247%.

In this study, a parameter of volume stability was proposed for the first time to design polymorph zirconia ceramics used for special components. A series of heterogeneous polymorph zirconia ceramics with various amounts of monoclinic (M) phase were fabricated by two-step sintering. Samples with about 27%, 31%, and 51% M phase content were selected to study the properties. The thermal shock durability was found to be associated with thermal expansion behavior and noncritical micro cracks, which both based on M phase initial content. In good agreement with experimental results, the correlation of normalized K versus M phase initial content was established. It could provide a repeatable reference to prepare special zirconia components without loss of density.

Droughts occurring more and more frequently in recent years are usually associated with progressive climate changes. Modern monitoring methods is mainly associated with agricultural use due to the high market demand for services protecting against agricultural losses. In natural wetland ecosystem this problem is neglected which is probably due to fact that this are ecosystems rich in water by definition. Nevertheless this droughts might become a problem of wetlands, whose good condition depends on adequate hydration. Therefore this study focused on determination Crop Water Stress Index (CWSI) for natural heterogeneous wetland habitats. CWSI based on remotely sensed land surface temperature and associated basic meteorological (air temperature and humidity) measurements. CWSI was calculated based on high resolution LST measurements from UAV platform and compare with on ground measurements of soil moisture, CCI, fAPAR and meteorological conditions. Results shows that CWSI properly shows water condition of plants in measured habitats and revels high importance of metrological conditions during data acquisition.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.

This paper investigates how blocks of buildings could fit into load shedding strategies. It focuses in particular on what could be the effects on peak shaving, occupants’ thermal comfort or CO2 emissions reduction and how to quickly quantify them. To achieve this goal, we focused on a new residential district, thermally fed by heat pumps. Four modeling approaches were confronted in order to estimate buildings' responses to load shedding orders. On the one hand, a quick estimation of the peak shaving impact can rely on experimental results if the buildings' envelope and uses of the experimentation match those of the study case. On the other hand, thermal simulation models allow us to assess thermal comfort while considering the building physical response. Finally, a hybrid modeling approach can provide a good compromise between modeling rapidity and accuracy of the impacts estimation. At district scale, it may be necessary to mix modeling approaches, from experimental results to detailed thermal models. Accuracy is not guaranteed for all approaches so that the choice should be made carefully in regards to study needs. However, results are sufficient to compare the effects of load shedding strategies on peak shaving, thermal comfort, and CO2 emissions reductions.

The quasi-two-dimensional organic charge-transfer salt κ-(BEDT-TTF)₂Cu₂(CN)₃ is one of the prime candidates for a quantum spin-liquid due the strong spin frustration of its anisotropic triangular lattice in combination with its proximity to the Mott transition. Despite intensive investigations of the material's low-temperature properties, several important questions remain to be answered. Particularly puzzling are the 6 K anomaly and the enigmatic effects observed in magnetic fields. Here we report on low-temperature measurements of lattice effects which were shown to be particularly strongly pronounced in this material (R. S. Manna et al., Phys. Rev. Lett. 104, 016403 (2010)). A special focus of our study lies on sample-to-sample variations of these effects and their implications on the interpretation of experimental data. By investigating overall nine single crystals from two different batches, we can state that there are considerable differences in the size of the second-order phase transition anomaly around 6 K, varying within a factor of 3. In addition, we find field-induced anomalies giving rise to pronounced features in the sample length for two out of these nine crystals for temperatures T < 9 K. We tentatively assign the latter effects to B-induced magnetic clusters suspected to nucleate around crystal imperfections. These B-induced effects are absent for the crystals where the 6 K anomaly is most strongly pronounced. The large lattice effects observed at 6 K are consistent with proposed pairing instabilities of fermionic excitations breaking the lattice symmetry. The strong sample-to-sample variation in the size of the phase transition anomaly suggests that the conversion of the fermions to bosons at the instability is only partial and to some extent influenced by not yet identified sample-specific parameters.

Theory of the Thermal Response Testing (TRT) is a well-known part of sizing process of the geothermal exchange system. Multiple parameters influence accuracy of effective ground thermal conductivity measurement; like testing time, variable power, climate interferences, groundwater effect etc. To improve accuracy of the TRT we introduced procedure to additionally analyze falloff temperature decline after power test. Method is based on a premise of analogy between TRT and petroleum well testing, since origin of both procedures lies in diffusivity equation with solutions for heat conduction or pressure analysis during radial flow. Applying pressure build-up test interpretation technique to the borehole heat exchanger testing, greater accuracy could be achieved since ground conductivity could be obtained from this period. Analysis was conducted on coaxial exchanger with five different power steps, and with both direct and reverse flow regime. Each test was set with 96hr of a classical TRT, followed by 96hr of temperature decline, making it almost 2000 hours of cumulative borehole testing. Results showed that ground conductivity value could vary as much as 25% depending on test time, seasonal period and power fluctuations while thermal conductivity obtained from a falloff period gives more stable values with only 10% value variation.