Considering the dynamic stall effects in engineering calculations is essential for correcting the aerodynamic loads acting on wind turbines, both during power production and stand-still cases, and impacts significantly the turbine aeroelastic stability. The employed dynamic stall model needs to be accurate and robust for a wide range of airfoils and range of angle of attack. The present studies are intended to demonstrate the performance of a recently implemented "IAG dynamic stall" model in a wind turbine design tool Bladed. The model is transformed from the indicial type of formulation into a state-space representation. The new model is validated against measurement data and other dynamic stall models in Bladed for various flow conditions and airfoils. It is demonstrated that the new model is able to reproduce the measured dynamic polar accurately without airfoil specific parameter calibration and has a superior performance compared to other models in Bladed.

The increasing variability in power plant load, in response to a wildly uncertain electricity market and the need to to mitigate CO₂ emissions, lead power plant operators to explore advanced options for efficiency optimization. Model-based, system-scale dynamic simulation and optimization are useful tools in this effort, and the subject of the work presented here. In prior work, a dynamic model validated against steady-state data from a 605 MW subcritical power plant was presented. This power plant model is used as a test-bed for dynamic simulations, in which the coal load is regulated to satisfy a varying power demand. Plant-level control regulates plant load to match an anticipated trajectory of the power demand. The efficiency of the power plant operating at varying load is optimized through a supervisory control architecture that performs set point optimization on the regulatory controllers. Dynamic optimization problems are formulated to search for optimal time-varying input trajectories that satisfy operability and safety constraints during the transition between plant states. An improvement in time-averaged efficiency of up to 1.8% points is shown feasible with corresponding savings in coal consumption of 184.8 tons/day and carbon footprint decrease of 0.035 kg/kWh.

Simultaneous Localization and Mapping (SLAM) is considered as a challenge in environments with many moving objects. This paper proposes a novel LiDAR Inertial Odometry framework, ID-LIO, for dynamic scenes that builds on LIO-SAM. To detect the pointclouds on the moving objects, a dynamic point detection method is integrated, which is based on pseudo occupancy along the spatial dimension. Then, we present a dynamic points propagation and removal algorithm based on indexed points to remove more dynamic points in the local map along the temporal dimension and update the status of the point features in keyframes. In the LiDAR odometry module, a delay removal strategy is proposed for history keyframes and the sliding window-based optimization includes the LIDAR measurement with dynamic weights to reduce error from dynamic points in keyframes. We perform the experiments both on the public low dynamic and highly dynamic data set. The results show that the proposed method greatly increases the localization accuracy in high dynamic environments. And the ATE(Absolute Trajectory Error) average RMSE((Root Mean Square Error) of our ID-LIO can be improved by 67% and 85% in the UrbanLoco-CAMarketStreet dataset and UrbanNav-HK-Medium-Urban-1 dataset respectively when compared with LIO-SAM.

Modern computational biology makes widespread use of mathematical models of biological systems, in particular systems of ordinary differential equations, as well as models of dynamic systems described in other formalisms, such as agent-based models. Parameters are numerical values of quantities reflecting certain properties of a modeled system and affecting model solu-tions. At the same time, depending on parameter values, different dynamic regimes - stationary, oscillatory, established as a result of transient modes of various types - can be implemented in the system. Predicting changes in the solution dynamics type depending on changes of model parameters is an important scientific task. Nevertheless, this problem does not have an analytical solution for all formalisms in a general case. The routinely used method of performing a series of computa-tional experiments, i.e. solving a series of direct problems with various sets of parameters fol-lowed by expert analysis of solution plots is labor-intensive with a large number of parameters and a decreasing step of the parametric grid. In this regard, the development of methods allow-ing to obtain and analyze information on a set of computational experiments in an aggregate form is relevant. This work is devoted to developing a method for visualization and classification of various dy-namic regimes of a model using a composition of the dynamic time warping (DTW-algorithm) and principal coordinates analysis (PCoA) methods. This method allows to obtain a qualitative visualisation of the results of the set of solutions of a mathematical model and to carry out the correspondence between the values of the model parameters and the type of dynamic regimes of its solutions. This method has been tested on the Lotka-Volterra model and artificial sets of var-ious dynamics

The colossal depths of the deep neural network sometimes suffer from ineffective backpropagation of the gradients through all its depths. Whereas, The strong performance of shallower multilayer neural structures prove their ability to increase the gradient signals in the early stages of training which easily gets backpropagated for global loss corrections. Shallow neural structures are always a good starting point for encouraging the sturdy feature characteristics of the input. In this research, a shallow, deep neural structure called PrimeNet is proposed. PrimeNet is aimed to dynamically identify and encourage the quality visual indicators from the input to be used by the subsequent deep network layers and increase the gradient signals in the lower stages of the training pipeline. In addition to this, the layerwise training is performed with the help of locally generated errors which means the gradient is not backpropagated to previous layers, and the hidden layer weights are updated during the forward pass, making this structure a backpropagation free variant. PrimeNet has obtained state-of-the-art results on various image datasets, attaining the dual objective of (1) compact dynamic deep neural structure, which (2) eliminates the problem of backwards-locking. The PrimeNet unit is proposed as an alternative to traditional convolution and dense blocks for faster and memory-efficient training, outperforming previously reported results aimed at adaptive methods for parallel and multilayer deep neural systems.

This study presents a dynamic model of a passenger vehicle and analyzes its dynamic characteristics and responses. A dynamic vehicle model with seven degrees of freedom was established to analyze the behavior of a driving vehicle. The vehicle model had three degrees of freedom for the motion of the sprung mass and four degrees of freedom for the unsprung masses. For this model, the equations of motion were derived using Lagrange’s equation. To verify the model, the suspension deformations computed using the model were compared with the deformations measured through three actual vehicle driving tests which are the slalom, double lane change, and step steer tests. Furthermore, we investigated the effects of suspension stiffness, suspension damping, and anti-roll bar torsional stiffness on the dynamic characteristics and responses of the vehicle model. The developed dynamic vehicle model may help vehicle designers predict the dynamic responses of a vehicle through simulation without performing a driving test.

Ensuring safe and continuous autonomous navigation in long-term mobile robot applications is still challenging. To ensure a reliable representation of the current environment without the need for periodic re-mapping, updating the map is recommended. However, in case of incorrect estimation of robot pose, updating the map can lead to errors that prevent the robot localisation and jeopardize map accuracy. In this paper, we propose a safe LIDAR-based occupancy grid map updating algorithm for dynamic environments taking into account the uncertainties in the estimation of the robot’s pose. The proposed approach allows robust long-term operations as it can recover the robot’s pose, even when it gets lost, to continue the map update process providing a coherent map. Moreover, the approach is robust also to temporary changes in the map due to the presence of dynamic obstacles such as humans and other robots. Results highlighting map quality, localisation performance, and pose recovery, both in simulation and experiments, are reported.

In this paper, the research progress on dynamic behaviors of RC structural members is reviewed from experimental, theoretical and numerical perspectives. Firstly, the basic overview, measurement methods, main conclusions and current limitations of available dynamic loading tests are presented. Then the theoretical studies on the dynamic constitutive models of RC materials, the dynamic increase factor (DIF) model for concrete and reinforcing steel and the proposed modified models of dynamic behavior parameter at the structural member level are summarized. Finally, the available modelling approach and the method for incorporating the dynamic effect in numerical simulation of RC structures are reviewed. Moreover, a brief introduction is made to the dynamic hysteretic model established on the experimental data, which provides an alternative approach to consider the dynamic effect beside the commonly used DIF method. This paper provides valuable reference for experimental studies and numerical simulations on the dynamic behaviors of RC structures, and also puts forward some issues that need to be solved in the future research works..

Based on functional magnetic resonance imaging and multilayer dynamic network model, the quantified temporal stability of brain network has shown potentials in predicting altered brain functions. The present review focuses on summarizing current knowledge on the commonly-used measures of brain network’s temporal stability and the clinical research progress on them. There are a variety of widely used measures of temporal stability such as the variance/standard deviation of dynamic functional connectivity strengths, the temporal variability, the flexibility (switching rate), and the temporal clustering coefficient, while there is no consensus to date that which measure is the best. The temporal stability of human brain networks may be associated with several factors such as sex, age, cognitive functions, head motion, and data preprocessing/analyzing strategies, which should be considered in the clinical studies. Multiple common psychiatric diseases such as schizophrenia, major depressive disorder, and bipolar disorder have been found to be related to altered temporal stability, especially during the resting state; generally, both excessively decreased and increased temporal stabilities were thought to reflect disease-related brain dysfunctions. However, the measures of temporal stability are still far from applications in clinical diagnoses for neuropsychiatric diseases partly because of the divergent results, and further studies are warranted.

First, a brief overview is provided on humanoid robots, and also models for the dynamic behavior are discussed. As base for these models these two methods Denavit-Hartenberg and Newton-Euler are used. Main aim of this work is to investigate the stability of a biped robot developed from IHRT. There is currently the low base of robot - consisting of feet, legs, hips and upper part of robots body. This structure currently has ten degrees of freedom.

Unsupported sleepers or void zones in ballasted tracks are one of the most recent and frequent track failures. The void failures have the property of intensive development that, without timely maintenance measures, can cause the appearance of cost-expensive local instabilities like subgrade damages. The reason of the intensive void development lies in the mechanics of the sleeper and ballast bed interaction. The particularity of the interaction is a dynamic impact that occur due to void closure. Additionally, void zones cause inhomogeneous ballast pressure distribution between the void zone and fully supported neighbour zones. The present paper is devoted studying the mechanism of the sleeper-ballast dynamic impact in the void zone. The results of experimental in-situ measurements of rail deflections showed the significant impact accelerations in the zone even for light-weight slow vehicles. A simple 3-beam numerical model of track and rolling stock interaction has shown the similar to the experimental measurements dynamic interaction. Moreover, the model shows that the sleeper accelerations are more than 3 times higher than the corresponding wheel accelerations and the impact point appear before the wheel enters the impact point. The analysis of ballast loadings shows the specific impact behaviour in combination with the quasistatic part that is different for void and neighbour zones, which are characterised with high ballast pre-stressed conditions. The analysis of void sizes influence demonstrate that the impact loadings, wheel and sleeper maximal accelerations appear at certain void depth after which the values decrease. The ballast quasistatic loading analysis indicates more than twice increase of the ballast loading in neighbour zones for long voids and almost full quasistatic unloading for short length voids. However, the used imitation model cannot explain the nature of the dynamic impact. The mechanism of the void impact is clearly explained by the analytic solution using a simple clamped beam. A simplified analytical expression of the void impact velocity shows that it is linearly related to the wheel speed and loading. The comparison to the numerically simulated impact velocities shows a good agreement and the existence of the void depth with the maximal impact. An estimation of the long-term influences for the cases of normal sleeper loading, high ballast pre-stress and quasistatic loading in the neighbour zones and high impact inside the void are performed.

We have developed a self-consistent model for predicting velocity of 1/2[111] screw dislocation in binary iron--carbon alloys gliding by a high-temperature Peierls mechanism. The methodology of modelling includes: (i) Kinetic Monte-Carlo (kMC) simulation of carbon segregation in dislocation core and determination the total carbon occupancy of the core binding sites; (ii) Determination of kink-pair formation enthalpy of a screw dislocation in iron---carbon alloy; (iii) KMC simulation of carbon drag and determination of maximal dislocation velocity at which the atmosphere of carbon atoms can follow a moving screw dislocation; (iv) Self consistent calculation of average velocity of screw dislocation in binary iron--carbon alloys gliding by a high-temperature kink-pair mechanism under constant strain rate. We conduct a quantitative analysis of the conditions of stress and temperature at which screw dislocation glide in iron--carbon alloy is accomplished by a high-temperature kink-pair mechanism. We estimate the dislocation's velocity at which screw dislocation brakes away from the carbon cloud and thermally-activated smooth dislocation propagation is interrupted by sporadic bursts controlled by athermal dislocation activity.

Rainfall runoff modeling has been a subject of interest for decades due to a need to understand a catchment system for management, for example regarding extreme event occurrences such as flooding. Tropical catchments are particularly prone to the hazards of extreme precipitation and the internal drivers of change in the system, such as deforestation and land use change. A model framework of dynamic TOPMODEL, DECIPHeR v1 - considering the flexibility, modularity and portability - and Generalized Likelihood Uncertainty Estimation (GLUE) method are both used in this study. They reveal model performance for the streamflow simulation in a tropical catchment, i.e. the Kelantan River in Malaysia, that is prone to flooding and experiences high rates of land use change. 32 years' continuous simulation at a daily time scale simulation along with uncertainty analysis resulted in a Nash Sutcliffe Efficiency (NSE) score of 0.42 from the highest ranked parameter set, while 25.35% of the measurement falls within the uncertainty boundary based on a behavioral threshold NSE 0.3. The performance and behavior of the model in the continuous simulation suggests a limited ability of the model to represent the system, particularly along the low flow regime. In contrast, the simulation of eight peak flow events achieves moderate to good fit, with the four peak flow events simulation returning an NSE > 0.5. Nonetheless, the parameter scatterplot from both the continuous simulation and analyses of peak flow events indicate unidentifiability of all model parameters. This may be attributable to the catchment modelling scale. The results demand further investigation regarding the heterogeneity of parameters and calibration at multiple scales.

Since the outbreak of 2019 novel coronavirus (2019-nCoV) at the hardest-hit city of Wuhan, the fast-moving spread has killed over three hundred people and infected more than ten thousands in China¹. There are more than one hundred cases outside of China, affecting a dozen of countries globally². The genome sequence of 2019-nCoV has been reported and fast diagnostic kits, effective treatment as well as preventive vaccines are rapidly being developed³. Initial fast-growing confirmed cases triggered lock-down of Wuhan as well as nearby cities in Hubei Province. Mathematical models have been proposed by scientists around the world to project the numbers of infected cases in the coming days ^4,5. However, major factors such as transportation and cultural customs have not been weighed enough. Our model is not set out for precise prediction of the number of infected cases, rather, it is meant for a glance of the dynamics under a public epidemic emergency situation and of different contributing factors. We hope that our model and simulation would provide more insights and perspective information to public health authorities around the globe for better informed prevention and containment solution.

Molecular dynamics simulations were carried out to investigate the atomic structure of a model Cu64Zr36 bulk metallic glass (BMG). It is found that the amount of icosahedral content of the system is significantly increased in a well relaxed structure. While we considered four connection types of vertex-, edge-, face-, and volume-sharing, the huge cluster in the relaxed samples mainly involve volume-type connection and exhibits a remarkable athermal plasticity that great stiffness and great yield strength compared to the as-quenched samples. In addition, the bond-angle distribution of annealed sample shows sharp peaks at specific bond angles which is an evidence of crystallized Laves-phase formed by icosahedral atoms, however the peaks are to be broaden after loading, which indicates decreasing amount of icosahedral content and their shape distortion. These results suggest that icosahedral content in a bulk metallic glasses plays a key role to determine the mechanical properties such as rigidity and maximum stress carrying capacity.

The study of values at European and global level has gained momentum along with the theory of values launched by Schwartz. Values are dormant, hidden, unobservable and impossible to measure directly. They exist somewhere within the human being, manifested by different attitudes, depending on their degree of generality. The paradigm of basic human values implies shared universal values that are encountered in cultures all over the world. The theory of values designed by Schwartz has refined the pool of 19 basic individual values representing principles in individuals and group, further describing the dynamic relationships among them. This study presents practical evidence of the dynamics between individual values, the dynamics theorized by Schwartz in 2012. Following the development of an online questionnaire made up of 46 items with online responses options on a Lickert scale from 1 to 6, where 1 represents less important and 6 represent very important, 220 young people from Western Romania voluntarily responded. By testing the hypothesis assuming the dynamic relationship between the two values through multiple regression analysis, the results demonstrate that in Model 1, which involves a linear relationship, health explains 42% of the variance in security with a F =161,215 significant at p <.01. In Model 2, which involves a curvilinear relationship, health explains 50% of the variance in security version with a F = 35,336 significant at p <.01. The incremental prediction optimization of 8% added by including the squared security accounts for the curve in the regression line, indicating the existence of a curvilinear relationship between security and health. The dynamic relationship demonstrates that upper limit and lower limit aspects of security, significantly influence the health value in a negative way. Normal levels of security trigger a high level of prioritization of health value. The implications of this type of relationship are discussed in explaining the value phenomenon at individual level. The study shows limits due to the selected sample, focusing exclusively on young people with higher education from the Western region of Romania. This sample was the target group of "The National Identity of Romanian Youth" project which designed this research.

A Smart Home is characterized by the presence of a huge number of small, low power devices, along with more classical devices. According to the Internet of Things (IoT) paradigm, all of them are expected to be always connected to the Internet in order to provide enhanced services. In this scenario, an attacker can undermine both the network security and the user’s security/privacy. Traditional security measures are not sufficient, because they are too difficult to setup and are either too weak to effectively protect the user or too limiting for the new services effectiveness. The paper suggests to dynamically adapt the security level of the smart home network according to the user perceived risk level what we have called network sentiment analysis. The security level is not fixed, established by a central system (usually by the Internet Service Provider) but can be changed with the users cooperation. The security of the smart home network is improved by a distributed firewalling and Intrusion Detection Systems both to the smart home side as to the Internet Service Provider side. These two parts must cooperate and integrate their actions for reacting dynamically to new and ongoing threats. Moreover, the level of network sentiment detected can be propagate to nearby home networks (e.g. the smart home networks of the apartments inside a building) to increase/decrease their level of security, thus creating a true in-line Intrusion Prevention System (IPS). The paper also presents a test bed for Smart Home to detect and counteract to different attacks against the IoT devices,,Wi-Fi and Ethernet connections .

This paper studies a model of dynamic compensation and capital structure with managerial traits. We show that Optimistic manager perceives equity as more undervalued than debt, while, confident manager perceives debt as more undervalued than equity. Managerial risk aversion mitigates manager’s bias. The risk aversion of the optimistic manager has a convex effect on the optimal coupon. There exists the level of risk aversion eliminating the bias on the leverage. The managerial optimist has an ambiguous effect on the owner’s bankruptcy level. The risk aversion has a convex effect on the owner’s bankruptcy level. The optimistic/confident manager underestimates the credit spread. The risk aversion has convex effect on the credit spread. In contrast to rational manager, the optimistic/confident manger has higher level of effort. The risk aversion has a negative effect on the effort.

Piezoelectric cantilever harvesters have a large power output at their natural frequency, but in some applications the frequency of ambient vibrations is different from the harvester’s frequency and/or ambient vibrations are periodic with some harmonic components. To cope with these operating conditions harvesters with integrated trimming devices (ITDs) are proposed. Some prototypes are developed with the aid of an analytical model and tested with an impulsive method. Results show that a small trimming device can lower the main resonance frequency of a piezoelectric harvester of the same extent as a larger tip mass and moreover generates at high frequency a second resonance peak. A multi-physics numerical FE model is developed for predicting the generated power and for performing stress-strain analysis of harvesters with ITDs. The numerical model is validated on the basis of experimental results. Several configurations of ITDs are conceived and studied. Numerical results show that harvesters with ITDs are able to generate relevant power at two frequencies owing to the particular shape of the modes of vibration. The stress in the harvesters with ITDs is smaller than the stress in the harvester with a tip mass trimmed to the same frequency.

For better export marketing strategies (EMS), companies mobilize their internal resources, which are managerial commitment, firm experience, and product uniqueness. However, Small businesses with constrained resources cannot be well explained with this view. So, more research on how small business come up with EMS have been called for. To explain how resource-restricted firms which rely heavely on entrepreneur, this study adopted the concept of dynamic managerial capabilities (DMCs) and resource versatility to better explain small business exports. We analyzed small businesses in Mongolia with qualitative research methods, including interviews with entrepreneurs and support organizations, site visits, and group discussions. We suggest international dynamic marketing capabilities (IDMCs), which are entrepreneurial orientation, networking capability, and versatile dynamic capability for small business. Theoretical and managerial implications are discussed.

Digital twins are the foundation of autonomous off-road vehicles. Dynamic reduction methods are one of several ways to develop digital twins for off-road vehicles. The article commences with a comprehensive overview of the most widely used dynamic reduction methods and then introduces performance metrics for assessing their efficacies in the context of digital twins. The paper additionally includes a detailed mathematical derivation of the state-space representation for reduced-order finite element models. The state-space representation of the reduced finite element models facilitates their export to problem-solving environments for dynamic analysis. The state-space models are eventually solved utilizing the built-in libraries of numerical solvers in textual and graphical programming platforms. In addition, the article identifies the set of solvers that best suit the simulation of virtual models for off-road vehicles. This article also includes an evaluation of the simulation results of digital models with modes ranging from 0 to 30 Hz. In addition, the article demonstrates the lower bound of the frequency range necessary and sufficient to be retained in off-road vehicle virtual models. Finally, the paper presents the simulation outcomes for digital models of commercial off-road vehicles with custom-built control, electrical, and control systems.

5G heterogeneous network overlaid by millimeter-wave (mmWave) access employs mmWave meshed backhauling as a promising cost-efficient backhaul architecture. Due to the nature of mobile traffic distribution in practice which is both time-variant and spatially non-uniform, dynamic construction of mmWave meshed backhaul is prerequisite to support the varying traffic distribution. Focusing on such scenario of outdoor dynamic crowd (ODC), this paper proposes a novel method to control mmWave meshed backhaul for efficient operation of mmWave overlay 5G HetNet through Software-Defined Network (SDN) technology. Our algorithm is featured by two functionalities, i.e., backhauling route multiplexing for overloaded mmWave small cell base stations (SC-BSs) and mmWave SC-BSs’ ON/OFF status switching for underloaded spot. In this paper, the effectiveness of the proposed meshed network is confirmed by both numerical analyses and experimental results. Simulations are conducted over a practical user distribution modeled from measured data in realistic environments. Numerical results show that the proposed algorithm can cope with the locally intensive traffic and reduce energy consumption. Furthermore, a WiGig (Wireless Gigabit Alliance certified) device based testbed is developed for Proof-of-Concept (PoC) and preliminary measurement results confirm the proposed dynamic formation of the meshed network’s efficiency.

Japanese encephalitis virus (JEV) causes acute viral encephalitis in humans and reproductive disorders in pigs. JEV emerged during the 1870s in Japan and since that time, JEV has been transmitted exclusively throughout Asia, according to known reporting and sequencing records. A recent JEV outbreak occurred in Australia which affected commercial piggeries across different temperate southern Australian states and caused confirmed infections in humans. A total of 47 human cases and seven deaths were reported. The recent evolving situation of JEV needs to be reported due to its continuous circulation in endemic regions and spread to non-endemics areas. Here, we reconstructed the phylogeny and population dynamics of JEV using recent JEV isolates for the future perception of disease spread. Phylogenetic analysis shows the most recent common ancestor occurred about 3120 years ago (YA) (95% Highest posterior density [HPD], 2680 to 3715). Our results of the Bayesian skyline plot (BSP) demonstrates that JEV demography lacks fluctuations for the last two decades, but it shows that JEV genetic diversity has increased during the last ten years. This indicates the potential JEV replication in the reservoir host, which is helping it to maintain its genetic diversity, and to continue its dispersal into non-endemic areas. The continuous spread in Asia and recent detection from Australia further support these findings. Therefore, an enhanced surveillance system is needed along with precautionary measures such as regular vaccination and mosquito control to avoid future JEV outbreaks.

Cable-Driven Parallel Robots (CDPRs) are a special kind of parallel manipulator which use cables to control the position and orientation of the mobile platform or end-effector. The usage of cables instead of rigid links offer some advantages over their conventional rigid counterparts. As cables can only pull, but not push, the number of cables (n) required to command the end-effector is always n+1. This configuration is known as fully-constrained and it is the most extended configuration for CDPRs. Although CDPRs have many advantages, such as their ability to cover large working areas, one of their main problems is that their working area (workspace) is limited in comparison to its frame area (planar case), or frame volume (spatial case), due to the minimum and maximum allowed tensions. Depending of these tensions values the workspace can be notoriously decreased. In order to tackle this problem, lots of works focus on solving kinematics or dynamics problems for cable sagging, i.e., they take into account sagging when modelling the robot kinematic and include these poses inside the usable robot workspace. Taking into account phenomenons like this increases the mathematical complexity of the problem, and much more complex techniques are required. On the other hand, the lack of workspace problem can be tackled by adding active or passive elements to the robot design. In this sense, this paper proposes two mechanical modifications: to add passive carriages to the robot frame and to use a single cable loop to command the end-effector position and orientation. This work presents the kinematic, static and dynamic models of the novel design and shows the gain of workspace for a planar case while taking into account different parameters of the robot.

Decision making is a complex process involving various parts of the brain which are active during different times. It is challenging to measure externally the exact instance when any given region becomes active during the decision-making process. Here we try to extract and visualize the dynamic functional brain activation information from the observed fMRI data. We propose the use of a regularized deconvolution model to simultaneously map various activation regions within the brain and track how different activation regions changes with time. Thus, providing both spatial and temporal brain activation information. The activation information can then be further analyzed as per need and requirements. The proposed technique was validated using simulated data and then applied to a simple decision-making task for identification of various brain regions involved in different stages of decision making. The visualization aspect of the algorithm allows us to actually see the flow of activation (and deactivation) in form of a motion picture. The dynamic estimate may aid in understanding the causality of activation between various brain regions in a better way.

Large water bodies such as the Laurentian Great Lakes have significant influences on local and regional climate through their unique physical features. Due to the coarse spatial resolution of general circulation models (GCMs), the Great Lakes are geometrically ignored in most GCMs. Thus, the dynamical downscaling technique serves as a necessary and feasible solution to bridge the gap. The Weather Research and Forecasting model (WRF) with an updated lake scheme is employed to downscale from a GCM, GFDL-CM3. The WRF-Lake’s performance is evaluated against observations, the GCM, as well as 23 other GCMs. Results show that the coupled air-lake model, with a fine spatial resolution and realistic lake bathymetries, reproduced a more reasonable spatiotemporal climatology than GCMs, as well as the lake-induced characteristics that were missed in GCMs. With lakes present, the seasonal variability of air temperature was reduced in WRF-Lake relative to GFDL-CM3, especially in summer. A reduced air temperature trend, about 4.5 °C/100 year in the 21st century, was projected in WRF-Lake. The seasonal evolutions of lake surface temperature and lake ice coverage were well captured by the lake model. The lake surface temperature was projected to be warming by 3.5-4 °C and the lake ice diminishing by 58.9% - 86%. Those results brought by the WRF-Lake model suggest that a fine resolution of the topography and the incorporation of the lake-atmosphere interactions are crucial to improve the understanding of the climate and climate change in the Great Lakes region.

The sustainability of ecotourism is the backbone of tourism development of a country. Ecotourism can contribute to both conservation and development in which involves dynamic relationship between tourism, biodiversity and communities, facilitate by great management. The purpose of this study is to analyze the dimensions of the socio-economic and environmental impacts of ecotourism in communities surrounding the Tasik Kenyir in Terengganu, Malaysia. This study provides a framework for the development and evaluation of ecotourism. The framework will determine if the relationships between indicators are positively correlated which will result in positive contribution to the other by using System Dynamic. Socio-cultural and economic data will be collected through interviews and group discussions in selected communities in Tasik Kenyir. Data on wildlife will be extracted from secondary data from Kenyir Research Institute, Universiti Malaysia Terengganu. The data analysis will explore the socio-cultural and economic differences between and within different communities due to ecotourism development, the contribution of ecotourism to conservation activities, local support for conservation and ecotourism as well as the influence of tourist activities on the distribution of wildlife species in Tasik Kenyir. This study aims to contribute toward understanding the natural resource community-ecotourism inter-relationship and help to bridge the knowledge gap that hinders biodiversity conservation initiatives. The findings will be used as a base for further development of ecotourism and will recommend alternative management options where necessary for the study area.

In this paper is shown the dynamic modeling and design of a passivity based controller for the RV-3SB robot. Firstly, the dynamic modeling of the of the Mitsubishi Rv-3SB robot is done by the Euler-Lagrange formulation in order to obtain a decoupled dynamic model considering the actuators orientation besides the position of this analyzed robot. It is important to remark that the dynamic model of the RV-3SB robot is done based in the kinematic model obtention in which is developed by the implementation of screw theory. Then the passivity based controller is obtained by separating the end effector variables and the actuator variables by making an appropriate coordinate transformation. The passivity based controller is obtained by selecting an appropriate storage function and by the Lyapunov theory the passivity based control law is obtained in order to drive the error variaable, which is the difference between the measured end effector position variable and the end effector desired position variable. The passivity based controller makes that the error variable reach the origin in finite time taking into consideration the dissipation properties of the proposed controller in order to stabilizes the desired end effector position. A numerical simulation experiement is performed in order to validate the theoretical results obtained in this research study. It is verified by numerical experimentation that the proposed control strategy is efficient and effective in order to drive the error variable to the origin in comparison with other modified techniques found in the literature. Finally, the appropriate discussion and conclusion of this research study are provided.

The study considers building a dynamic model of profit maximization for the car-sharing system and its verification on the example of implementing such a system in Astana (Republic of Kazakhstan). The region, bounded by the administrative boundaries of Astana, was divided into subregions by covering the region with regular hexagons placed side by side. A dataset was built with information on 1168 trips to Astana from January to March 2023. The Kepler visualization service constructed maps of the beginning and end of trips in the region and a map of trips binding to the hexagonal grid cells. Each cell of the grid corresponds to a specific sub-region, for which the quantitative parameters necessary for solving the profit maximization problem in the car-sharing system are calculated. Stations with cars will be placed in the cells of the grid, which will be available to car-sharing service customers. Based on the collected data, a dynamic (four periods per day) and static profit maximization model in the car-sharing system was built. Modeling was carried out based on the built models in the example of Astana. It was established that using a dynamic model of profit maximization in the car-sharing system increases the profit by 3.7%.

The heterogeneous structure implies that a few nodes may be crucial in maintaining network structural and functional properties. Identifying these crucial nodes correctly and quickly is a primary issue as contemporarily may face the mushrooming of large-scale datasets. Besides, the ‘weight issue’ is always ignored in this field which edge weight may play a positive/negative role in contributing to the node importance in different weighted networks. This paper provides a novel algorithm, Weighted Expectation Algorithm (WEA), which aims to ensure accuracy and speed of computation by taking advantage of dynamic programming to better handle the task of large-scale networks. Additionally, the weight issue that edge weights may contribute differently is addressed by a simply quantitative definition. Two standard experiments show WEA can maintain the network structure in connectivity well (by the lowest average robustness 0.192) and identify the node importance better in the spreading function test of spreading dynamics (by the highest average Kendall’s tau-b 0.678). In addition, the time complexities of different algo-rithms are evaluated, and their time-consuming are tested, proving that WEA consumes a rela-tively short time.

A proxy war, between a coalition of countries, BLUE and a country, RED, is considered. RED wants to increase the size of the RED territory. BLUE wants to involve more regions in trade and other types of cooperation. GREEN is a small and independent nation that wants to become a member of BLUE. RED attacks GREEN and tries to invade. BLUE decides to give optimal arms support to GREEN. This support can help GREEN in the war against RED and simultaneously reduce the military power of RED, which is valuable to BLUE, also outside this proxy war, since RED may confront BLUE also in other regions. The optimal control problem of dynamic arms support, from the BLUE perspective, is defined in general form. The objective function is a weighted sum of the present value of the free GREEN territory and the present value to BLUE of the net loss of military resources in the RED army. The net loss of RED at a particular point in time is a function of the location of the front line and the size of the mobile GREEN forces behind the RED line. First, it is assumed that the expected net loss is proportional to the force ratio behind the red front line. It is proved that the net loss function is a strictly concave quadratic function of x, the location of the front line. It is also proved that the unique maximum of the net loss function occurs at the same front location, also if the net loss function is proportional to the strength ratio behind the RED lines, raised to any strictly positive exponent. From the BLUE perspective, there is an optimal position of the front. This position is a function of the weights in the objective function and all other parameters. Optimal control theory is used to determine the optimal dynamic BLUE strategy, conditional on a RED strategy, which is observed by BLUE military intelligence. The optimal arms support strategy for BLUE is to initially send a large volume of arms support to GREEN, to rapidly move the front to the optimal position. Then, the support should be almost constant during most of the war, keeping the war front location stationary. In the final part of the conflict, when RED will have almost no military resources left and tries to retire from the GREEN territory, BLUE should strongly increase the arms support and make sure that GREEN rapidly can regain the complete territory and end the war

Fuel consumption, subsequent emissions and safe operation of class 8 vehicles are of prime importance in recent days. It is imperative that the vehicle operates in its true optimal operating region given a variety of constraints such as road grade, load, gear shifts, Battery State of charge (for hybrid vehicles), etc. In this paper a research study is conducted to evaluate the fuel economy and subsequent emission benefits when applying predictive control to a mild hybrid line haul truck. The problem is solved using a combination of dynamic programming with back tracking and model predictive control. The specific fuel saving features that are studied in this work are dynamic cruise control, gear shifts, vehicle coasting and torque management. These features are evaluated predictively as compared to a reactive behavior. The predictive behavior of these features are a function of road grade. The result and analysis shows significant improvement in fuel savings along with NOx benefits. Out of the control features dynamic cruise (predictive) control and dynamic coasting showed the most benefits while predictive gear shifts and torque management (by power splitting between battery and engine) for this architecture did not show fuel benefits but provided other benefits in terms of powertrain efficiency.

This article is a theoretical contribution to mental model research, which currently has different threads. Whereas some researchers focus on the perceived causal structure, others also include decision policies and decisions. We focus on the link between recognized causal structure (“mental models of dynamic systems”) and policies, proposing Johnson-Laird’s theory of mental models as the link. The resulting framework hypothesizes two types of systematic mental model errors: (1) misrepresentation of the system’s structure and (2) failure to deploy relevant mental models of possibilities. Examination of three experiments through this lens reveals errors of both types. Therefore, we propose that the cognitive theory of mental models opens a path to better understand how people construct their decision policies and develop interventions to reduce such mental model errors. The article closes by raising several questions for empirical studies of the reasoning process leading from mental models of dynamic systems to decision policies.

Oncogenic protein E6 from Human Papilloma Virus 16 (HPV-16) mediates the degradation of Membrane-associated guanylate kinase with inverted domain structure-1 (MAGI-1), throughout the interaction of its protein binding motif (PBM) with the Discs-large homologous regions 1 (PDZ1) domain of MAG1-1. Generic variation in the E6 gene that translates to changes in the protein’s amino acidic sequence modifies the interaction of E6 with the cellular protein MAGI-1. MAGI-1 is a scaffolding protein found at tight junctions of epithelial cells, where it interacts with a variety of proteins regulating signaling pathways. MAGI-1 is a multidomain protein containing two WW (rsp-domain-9), one guanylate kinase-like, and six PDZ domains. PDZ domains played an important role in the function of MAGI-1 and served as targets for several viral proteins including the HPV-16 E6. The aim of this work was to evaluate, with an in silico approach, employing molecular dynamics simulation and protein-protein docking, the interaction of the intragenic variants E-G350 (L83V), E-C188/G350 (E29Q/L83V), E-A176/G350 (D25N/L83V), E6-AAa (Q14H/H78Y/83V) y E6-AAc (Q14H/I27RH78Y/L83V) and E6-reference of HPV-16 with MAGI-1. We found that variants E-G350, E-C188/G350, E-A176/G350, AAa and AAc increase their affinity to our two models of MAGI-1 compared to E6-reference.

Objectives: To investigate the value of early lactate dynamic monitoring index in predicting prognosis of patients with sepsis and septic shock. Methods: We performed our test on 50 patients. Out of 50 patients, 28 are male, and 22 are female. Prospectively studied pediatric patients with septic shock were performed. Vital signs, Lactate clearance, were obtained at presentation 6 h, 12 h, 24 h over the first 48 h of hospitalization. The therapy received, outcome parameters of mortality and duration of hospitalization were recorded. Results: The statistical data and comparative analysis showed that an average of 16.88 days after admission, 5 patients have died, 17 patients are poorly prognosis leaves the hospital, and the remaining 28 are recovered and discharged. The primary outcome variable of mean 16 days hospitalization mortality rate was 10%. Poor prognosis 34% and fully recovery 56 % were observed. In this retrospective cohort study, a lactate level of more than 2.5mmol/L was the best threshold to predict 28-day mortality among severe sepsis and septic shock patients. In our research, we found mean LC 6 h 3.08mmol/L, and after 48 h mean it is 1.79mmol/L. Significant LC 6 h found, which is 8.08mmol/L in the death group patient where 48 h mmol/L shows significant high. Poor prognosis also presents a clinical increase of lactate level high in the LC 6 h analysis, which is 3.32mmol/L. Recovered patients showed a significant improvement after administering treatment depending on the patient organ involvement and good decrease of lactate reports achieved, which is 1.20mmol/L, where admission reports show it was 1.91mmol/L in LC 6 h. Mean Heart rate 94/51mmhg, pulse 119, temperature 39℃, respiratory rate 32.26, and urine output 456 ml recorded during our study. Death patient shows a remarkable detonation of those reports but has a significant clinical report with the recovered patients. Conclusion: The early lactate dynamic monitoring index has a high value in predicting sepsis and septic shock patients' prognosis, thus worth popularizing.

It is challenging to apply heat flow through a thermal bridge, which requires the analysis of 2D or 3D heat transfer to building energy simulation(BES). Research on the dynamic analysis of thermal bridges has been underway for many years, but their utilization remains low in BESs. This paper proposes a thermal bridge modeling and a dynamic analysis method that can be easily applied to BESs. The main idea begins with an analogy of the steady-state analysis of thermal bridges. As with steady-state analysis, the proposed method first divides the thermal bridge into a clear wall, where the heat flow is uniform, and the sections that are not the clear wall (the thermal bridge part). For the clear wall part, the method used in existing BESs is applied and analyzed. The thermal bridge part (TB part) is modeled with the linear time-invariant system (LTI system) and the system identification process is performed to find the transfer function. Then, the heat flow is obtained via a linear combination of the two parts. This method is validated by comparing the step, sinusoidal and annual outdoor temperature response of the finite differential method(FDM) simulation. When the thermal bridge was modeled as a third-order model, the root mean square error(RMSE) of annual heat flow with the FDM solution of heat flow through the entire wall was about 0.1W.

In this paper, drug treatment and vaccination are compared healthy and economically. In this comparison, in addition to comparing economic costs, it has paid attention to patients' recovery. To reach the goal, the prevalence of Covid-19 virus in New York is modeled by using the SEIR dynamic model. The SEIR dynamic model is used to model the period of epidemic diseases. Then, three disease control scenarios are evaluated economically. Treatment and vaccination are two important issues in controlling epidemic diseases. To control the disease, each of these two methods has economic costs and benefits. The main purpose of this paper is to compare the two methods of vaccination and treatment economically. Although the results of the study show that vaccination can be effective in preventing the epidemic of the disease than treatment, but due to the high cost and genetic mutation of the virus, vaccination is not the optimal method for both health and the economy in the long term.

China is not only short of fresh water resources per capita, but also faces a serious problem of water pollution in recent years, with 190 million people suffering from excessive levels of harmful substances in their drinking water. Such as arsenic poisoning and fluorosis and other endemic water diseases high incidence. As a series of water pollution prevention plan of action by the Chinese government announced that, this paper uses the modified Undesirable Dynamic Network model empirical analysis of China's 31 provincial administrative region economic growth, wastewater treatment, and water disease control efficiency between 2013 and 2017. The results show that the efficiency of water pollution disease in all four regions of China and the total efficiency in the three regions of east, west and central China all show a decreasing trend, and the efficiency scores and rankings of all provinces and cities within the region fluctuate greatly. The eastern region with the most developed economy has the best overall performance, with higher efficiency in Water consumption and Water disease control. However, the efficiency of wastewater treatment in northeast China is stable and better. Given the high level of economic development in China and the results of the above mentioned efficiency in water pollution and water diseases, improving the efficiency and quality of wastewater treatment in China is regarded as an important factor in achieving the strategic goal of green growth.

This paper puts forward an alteration for Tensor Calculus utliized in a coordinate system which is under a dynamic distortion drawing inspiration from similar fields such as the Calculus of Moving Surfaces (CMS). The paper establishes transformation laws for Tensors within these regions and establishes Operators such as the Tensorial Field Derivative which enforce a Tensorial Transformation on Tensors defined within a Dynamically Moving coordinate system. This variation of Tensor Calculus can be utilized to observe how disciplines such as QFT and Continuum Mechanics would change to accomodate for a distorting coordinate system and can be utliized to develop new theoretical models which account for this temporal distortion particularly within Biological Settings.

This paper presents performed Ansys numerical simulation on WindFloat structures. It contributes to the methodology of calculation based on CFD instruments to study the movements of the waves on semi-submersible stationary structures and highlights the importance of using RAO functions. RAO numerical approach developed can be applied to design semisubmersible WindFloat structures in order to fulfill essential requirements regarding operational safety and design. Numerical methodology was designed in accordance marine loads and the I.T.T.C. recommendations. The numerical RAO results for regular wave movements include many elements for the semi-submergible structure. Close results to open sea operation can be achieved by constant improvement in numerical simulation methodologies. The work opens the way for further hydrodynamic development on irregular waves for realistic hydrodynamic and structural response of the actual semi-submersibles at sea. The results demonstrate the accuracy of RAO function approach for specific WindFloat in Jonswap spectrum.

Here, we present a series of novel block copolymers (BCP) from bio-derived monomers, poly(lactic acid)-block-poly(2,5-furandimethylene succinate) (PLA-b-PFS), in which the furan groups from PFS block can be crosslinked with bis(maleimido) triethylene glycol (M2) through a Diels-Alder reaction. This dynamic crosslinking reaction leads to a network structure for enhancing the mechanical properties compared to their linear BCP analogous. Decreasing the crosslinking density leads to a decrease of glass transition temperature of BCPs and a transition from glassy to rubbery-like behavior at room temperature. This allows a wide tunablity of both elastic moduli and yields of the materials. For the lowest crosslinking density. the material exhibits an over 50% self-healing efficiency at room temperature after five days, attributed to the low Tg (15.2 C) from the introduction of PFS block, allowing sufficient chain mobility for structure re-organization. Moreover, with the appropriate selection of crosslinking density (PLA-b-PFS/M2 (6/1)), it also shows an excellent shape memory property with a high recovery rate of 96.3% and a fixity rate of 97.3%. The permanent shape can be rewriteable due to the reversibility of Diels-Alder reaction. With these advanced functionalities and ease in large-scale fabrication, the PLA-b-PFS/M2 shows great promises for self-healing coatings or films with shape memory properties in a wide variety of applications such as packaging materials

The excessive vibration caused by crowds walking across footbridges has attracted great public concerns in the past few decades. This paper presents, from considering the dynamic characteristics of the bipedal crowd model, a new stability limit criterion based on the bipedal excitation model. The stability limit can be used to estimate the upper boundary of crowd size. In addition, the dynamic stable performances of a structure, under a certain walking crowd size, can be predicted by the stability criterion. This proposed mechanism provides an alternative comprehension how crowd excite the excessive sway motion with a large-span structure.

Websites and applications use personalisation services to profile their users, collect their patterns and activities and eventually use this data to provide tailored suggestions. User preferences and social interactions are therefore aggregated and analysed. Every time a user publishes a new post or creates a link with another entity, either another user, or some on-line resource, new information is added to the user profile. Exposing private data does not only reveal information about single users' preferences, increasing their privacy risk, but can expose more about their network that single actors intended. This mechanism is self-evident on \emph{social networks} where users receive suggestions based on their friends' activity. We propose an information theoretic approach to measure the differential update of the anonymity risk for time-varying user profiles. This expresses how privacy is affected when new content is posted and how much third party services get to know about the users when a new activity is shared. We use real Facebook data to show how our model can be applied on a real world scenario.

As we all know, many more dynamic objects appear almost continuously in real world, which are immensely able to impair the performance of the majority of vision-based SLAM systems that are based on the static-world assumption. In order to improve the robustness and accuracy of visual SLAM in the high dynamic environment, a real-time and robust stereo SLAM system for dynamic scenes was proposed. To weaken influences of dynamic content, the moving object detection method was put forward in our visual odometry, then the semantic segmentation network was combined into our stereo SLAM to extract pixel-level contours of dynamic objects. Then influences of dynamic objects were extremely weaken and the performance of our system was increased markedly in dynamic, complex and crowed city spaces. Experiment with both on KITTI Odometry dataset and in a real-life scene, the results show that our method can dramatically decrease the tracking error or drift, improve the robustness and stability of our stereo SLAM in high dynamic outdoor scenarios.

In recent years, the production of renewable energy represents one of the main challenges of modern and future society. The new cultivation method called Agrivoltaic (hereafter AV), combines and associates agricultural production and renewable energy (photovoltaic) production in a collaborative synergy from which both benefit. In this study, the dry matter and essential oils yield of six medicinal species (Salvia officinalis L., Origanum vulgare L., Rosmarinus officinalis L., Lavendula angustifolia L., Thymus citriodorus L. and Mentha spicata L.) grown underneath a dynamic AV system in comparison to those in full sun (T), were evaluated. In particular, below the dynamic AV system, due to the rotation of the panels, two plot areas on the ground were distinguished: one always covered by the panels (UP), and another one covered alternatively (BP). During the aromatic crop cycles, the solar radiation, infrared leaf temperature and air temperatures in UP, BP and T plot, were measured. In addition, at harvest time, weed survey was carried out. The results showed that, in general, the solar radiation and infrared leaf temperature were lower in UP plot than in either the BP and T plots, while the air temperatures were similar in all compared plots. Also the weed cover percentage was lower in the UP plot than other ones. The essential oils yield in the sage, thyme, mint and rosemary plants were higher in both UP and BP plots than for T plot. Thus, shading and/or less weed infestation may have been the main factors favorably influencing the performance of medicinal crops under a dynamic AV system.

Dynamic Realistic Failure Process Analysis (DRFPA) is a numerical software based on FEM it is firstly validated by comparing with the experimental test. Such validation is carried out under two consistent concrete specimens under uniaxial compression. After validation, DRFPA is used to study the influence of two parallel pre-existing crack inclination angles on the fracture of concrete under dynamic loads. The evolution of wing cracks and secondary cracks is investigated by observing the initiation, coalescence, and propagation of them. Meanwhile, the relationship between failure mode and inclination angles is discussed via analyzing the acoustic emission events. Finally, it is concluded the relationship between inclination angles of pre-cracks and performance/stability of concrete structure.

Human behaviour was tipped as the mainstay in the control of further SARS-CoV-2 (COVID-19) spread especially after the lifting of restrictions by many countries. Countries in which restrictions were lifted soon after the first wave, had subsequent waves of the COVID-19 infections and it remains to be seen whether there will be more waves. In this paper, we formulate a deterministic model for COVID-19 incorporating dynamic non-pharmaceutical interventions, dubbed social dynamics. The model steady states are determined and their stability analysed. Numerical simulations are carried out to determine the pack of various parameters that influence the social dynamics. In South Africa, the first wave was the only wave in which the only interventions rested solely on human behavior. The model is thus fitted to COVID-19 data on the first wave in South Africa. The results presented in this paper have implications on the trajectory of the pandemic in the presence of changing social processes.

One of the central criteria for free will is “Could I have done otherwise?” But because of a temporal asymmetry in human choice, the question makes no sense. The question is backward-looking, while human choices are forward-looking. At the time when any choice is actually made, there is as of yet no action to do otherwise. Expectation is the only thing to contradict (do other than). So the ability to do something not expected by the ultimate expecter, Laplace’s demon, is a better criterion for free will. If human action is fundamentally unpredictable, then we have free will. Scientists have studied a form of fundamental unpredictability, known as undecidability. The features that make a system capable of undecidable dynamics have been identified: program-data duality; potential to access an infinite computational medium; and the ability to implement negation. Humans have all three of these features, so we very likely are fundamentally unpredictable, so we have free will.

The fault diagnosis of the gearbox is primarily based on the analysis of the harmonic response. However, the generation mechanism of the harmonic response of the gear pair is still not distinctly explained in a healthy gearbox. Therefore, this paper is dedicated to establishing a dynamic model of the gearbox for this issue. In this model, the contact force of the bearing and the meshing stiffness of the gear pair are determined by the Hertz theory and the potential energy method, then the shaft motion is used as the connection to establish the coupling relationship between the gear pair and the bearing. After this dynamic model is confirmed by experiments and existing models, the coupling relationship inside the gearbox and the harmonic response of the gear pair are studied using this model. The result demonstrates that a closed control loop is formed due to the vibration transmission between the gear pair, the bearing and the shaft, and there is a strong coupled vibration between the gear pair and the bearing in the gearbox. Due to the generation of the center distance error, misalignment angle and disorganized meshing process of the gear pair, the meshing stiffness is altered, which excites the harmonic response of the gear pair. When the speed of the gearbox is increased, although the vibration amplitude of the gearbox is increased, the system predominantly vibrates at the fundamental frequency, and the harmonic of the gear pair is also shifted to the low frequency band.

Emergence of multi drug resistant (MDR) and extensively drug resistant (XDR) Mycobacterium tuberculosis poses a serious threat to TB control as the available treatment options are less effective in these cases. Therefore, new strategies are required for identification of new drugs and drug targets. The M. tuberculosis dihydrodipicolinate synthase is a putative drug target with no potent inhibitor. Here in this study, we have used a comprehensive computational approach to identify small molecule inhibitors and validated them in vitro. As similar structures tend to have similar functions, therefore 3 approaches, namely, (a) known inhibitor-based approach, (b) substrate analogues, (c) product analogues were used for compound screening from various chemical libraries. The fourth approach we have taken is fragment library screening.In vitro studies revealed that β-hydroxypyruvic acid tartronic acid are inhibitors of Mtb-rDapA with maximum inhibition 48% and 51% at 500µM concentrations respectively. We have also observed that β-hydroxypyruvic acid is a time dependent inhibitor of Mtb-rDapA. Further, thermal shift assays showed that β-hydroxypyruvic acid interacts with Mtb-rDapA and the thermal stability of Mtb-rDapA shifted by 3˚C. Among the product analogues of Mtb-DapA, dipicolinic acid showed to bind to Mtb-rDapB shifting thermal stability of Mtb-rDapB by 0.5˚C in binding. Additionally, we have designed a new approach by combining substrate and product analogues to achieve better inhibitions. In vitro assays validated that this combination approach increased maximum inhibition up to 100%. We envision that these compounds would serve as potent leads for tuberculosis drug discovery.

This paper presents a robust method based on graph topology to find the topologically correct and consistent subset of inter-robot relative pose measurements for multi-robot map fusion. However, the absence of good prior gives a severe challenge to distinguish the inliers and outliers, and wrong loop closures can seriously corrupt the fused global map. Existing works mainly rely on the consistency of spatial dimension to select inter-robot measurements, which does not always hold. In this paper, we propose a fast inter-robot loop closure selection method that integrates the consistency and topology relationship of measurements, which both conform to the continuity characteristics of similar scenes and spatiotemporal consistency. The traditional high-dimensional consistency matrix is decomposed into the sub-matrix blocks corresponding to the overlapping trajectory area. Building on this logic, a clustering method involving topology correctness of inter-robot loop closures is introduced to split the entire measurement set into multiple clusters. We define the weight function to find the maximum cardinality subset with topologically correct and consistent, then convert the weight function to a maximum clique problem in the graph and solve it. We evaluate the performance of our method in a simulation and in a real-world experiment. Compared to state-of-the-art methods, the results show that our method can achieve competitive performance in accuracy while reducing computation time by 75%.

The optoelectronic properties of free standing monolayer (ML) hexagonal boron nitride (h-BN) is investigated for potential solar energy conversion applications using the Density Functional Theory (DFT) full potential linearized augmented plane wave (FP-LAPW) method. In addition, the bulk optical properties have also been calculated for the sake of comparison. The dielectric functions, optical conductivities and the optical constants are evaluated using the relaxed structures from electronic total energy pseudopotential calculations. The results reinforce previous research on h-BN DUV optoelectronics and demonstrate the suitability of its use as a component in deep ultraviolet (DUV) and energy conversion devices.

Purpose: While resultant maximal voluntary contraction (MVC) is commonly used to assess muscular performance, the simultaneous activation of antagonist muscles could dramatically underestimate the strength of the agonist muscles. While quantification of antagonist torque has been performed in plantar- (PF) and dorsi-flexion (DF) joint in isometric conditions, it has yet to be determined in anisometric (concentric and eccentric) conditions. Methods: The experiment was performed in 9 participants through 2 sessions (reliability). The MVCs in DF and PF were measured in isometric, concentric and eccentric conditions (10°.s^-1). Electromyographic (EMG) activities from the soleus, gastrocnemius medialis and lateralis, and tibialis anterior muscles were simultaneously recorded. The EMG biofeedback method was used to quantify antagonist torque, where participants were asked to maintain a level of EMG activity, corresponding to antagonist EMG activity and related to the muscle contraction type, according to a visual EMG bio-feedback displayed on a screen. Results: Resultant torque significantly underestimated agonist torque in DF MVC (30-65%) and to a lesser extent in PF MVC (3%). Triceps surae antagonist torque was significantly modified with muscle contraction type, showing higher antagonist torque in isometric (29 Nm) than eccentric (23 Nm, p < 0.001) and concentric (14 Nm, p < 0.001) conditions and resulting in modification of the DF MVC torque-velocity shape. The difference between DF eccentric and concentric MVC was attenuated when considered agonist torque (12%) rather than resultant torque (45%). Conclusion: Estimation of the antagonist torque in isometric or anisometric condition brings new insights to assessment of muscular performance and could result in costly misinterpretation in strength training and/or rehabilitation programs.

Based on the recorded watershed characteristics, the future conditions on the basin system can be predicted using a different method. In this study, dynamic land-use change and its impacts on the streamflow for the Dabus watershed were predicted using ANN-CA based method. The model performance for accurate prediction of the future land-use change on the Dabus River watershed has been checked by validation of the simulated value with the actual value, hence the overall kappa value (k) = 0.83 for the simulated 2016-LULC validated with actual 2016-LULC. Then, 2026-LULC was predicted based on the 2004 and 2009-LULC. The streamflow for the case of 2004 and 2009-LULC has been simulated using the SWAT model. The value of NSE = 0.87 and 0.90 was attained during validation of simulated streamflow for 2004 and 2009-LULC data cases, respectively. The agreement of simulated value of streamflow with the observed data is indicated as R2 = 0.91 and 0.96 for 2004-LULC and 2009-LULC. The effects of the dynamic land-use change on streamflow for the predicted land use(2026-LULC) catchment were evaluated by T-test analysis. Hence, T-stat =0.04 and -0.002 in the case of simulated streamflow used 2004-LULC and 2009-LULC, respectively compared with simulated value using 2026-LULC.

This review describes the subjective experience of visual aura in migraine, outlines theoretical models of this phenomenon, and explores how these may be linked to neurochemical, electrophysiological and psychophysical differences in sensory processing that have been reported in migraine with aura. Reaction-diffusion models have been used to model the hallucinations thought to arise from cortical spreading depolarisation and depression in migraine aura. One aim of this review is to make the underlying principles of these models accessible to a general readership. Cortical spreading depolarisation and depression in these models depends on the balance of the diffusion rate between excitation and inhibition, and the occurrence of a large spike in activity to initiate spontaneous pattern formation. We review experimental evidence, including recordings of brain activity made during the aura and attack phase, self-reported triggers of migraine, and psychophysical studies of visual processing in migraine with aura, and how these might relate to mechanisms of excitability that make some people susceptible to aura. Increased cortical excitability, increased neural noise, and fluctuations in oscillatory activity across the migraine cycle are all factors likely to contribute to the occurrence of migraine aura. There remain many outstanding questions relating to the current limitations of both models and experimental evidence. Nevertheless, reaction-diffusion models, by providing an integrative theoretical framework, support the generation of testable experimental hypotheses to guide future research.

This work investigates the influence of strain rate on the stress/strain behaviour of Scalmalloy. This material is an aluminium-scandium-magnesium alloy, specifically developed for additive manufacturing. The bulk yield stress of the material processed by Selective Laser Melting is approximately 340 MPa which can be increased by heat-treating to approximately 530 MPa. These numbers, combined with the low mass density of 2.7 g/cm3, make Scalmalloy an interesting candidate for lightweight crash-absorbing structures. As this application is inherently dynamic, it is of interest to study the loading rate sensitivity, which is difficult to predict: Al-Sc alloys exhibit classic strain rate sensitivity with an increased yield stress at elevated strain rates. However, Al-Mg alloys are known to show the contrary effect, they exhibit less strength as strain rate is increased. To answer the question how these effects combine, we study the dynamic behaviour at four different strain rates ranging from 10−3 /s to 1000 /s using servo-hydraulic and Split-Hopkinson testing methods. The resulting data is analysed in terms of strain rate sensitivity of tensile strength and failure strain. A constitutive model based on a simplified Johnson-Cook approach is employed to simulate the tensile tests and provides good agreement with the experimental observations.

This investigation explores a novel path-planning and optimization strategy for multiple cooperative robotic agents, applied in a fully observable and dynamically changing obstacle field. Current dynamic path planning strategies employ static algorithms operating over incremental time-steps. We propose a cooperative multi-agent (CMA) based algorithm, based on natural flocking of animals, using vector operations. It is preferred over more common graph search algorithms like A* as it can be easily applied for dynamic environments. CMA algorithm executes obstacle avoidance using static potential fields around obstacles, that scale based on relative motion. Optimization strategies including interpolation and Bezier curves are applied to the algorithm. To validate effectiveness, CMA algorithm is compared with A* using static obstacles due to lack of equivalent algorithms for dynamic environments. CMA performed comparably to A* with difference ranging from -0.2% to 1.3%. CMA algorithm is applied experimentally to achieve comparable performance, with an error range of -0.5% to 5.2%. These errors are attributed to the limitations of the Kinect V1 sensor used for obstacle detection. The algorithm was finally implemented in a 3D simulated space, indicating that it is possible to apply with drones. This algorithm shows promise for application in warehouse and inventory automation, especially when the workspace is observable.

Environmental decentralization (ED), or the allocation of environmental protection affairs and responsibilities among various administrative authorities, affects the effectiveness of environmental regulation in promoting green total factor productivity (GTFP). Based on panel data of 30 Chinese provinces from 2001 to 2015, this paper employs dynamic panel models to test the effects of environmental regulations (environmental protection investment, ENV; pollutant discharge fees, PDF) on GTFP, with or without being influenced by ED. Without the impact of ED, GTFP is significantly inhibited by ENV while significantly promoted by PDF. Considering the impact of ED, with the strengthening of ED, the negative effects of ENV on GTFP is significant; contrarily, the positive effects of PDF on GTFP is significant; improving provincial ED adds negative effects of ENV, while reduces the positive effects of PDF; increasing prefectural ED reduces negative effects of ENV; expanding county-level ED adds the positive effects of PDF. Therefore, to boost GTFP growth, prefectural environmental protection authorities should have more autonomy in ENV, while the county-level should have more autonomy in PDF.

Neuromuscular disorders cause progressive muscular weakness, which limits upper extremity mobility and performance during activities of daily life. A dynamic arm support can improve mobility and quality of life. However, their use is often discontinued over time for unclear reasons. This study aimed to evaluate whether users of dynamic arm supports demonstrate and perceive quantifiable mobility benefits over a period of two months. Nine users of dynamic arm supports were included in this observational study. They had different neuromuscular disorders and collectively used four different arm supports. They were observed for three consecutive weeks during which they were equipped with a multi-sensor network of accelerometers to assess the actual use of the arm support and they were asked to provide self-reports on the perceived benefits of the devices. Benefits were experienced mainly during anti-gravity activities and the measured use did not change over time. The self-reports provided contextual information in domains such as participation to social life, in addition to the sensor system. However self-reports overestimated the actual use by up to three-fold compared to the accelerometer measures. A combination of objective and subjective methods is recommended for meaningful and quantifiable mobility benefits during activities of daily life.

Biofuels and biochemicals play significant roles in the transition towards a fossil-free society. However, large-scale biorefineries are not yet cost-competitive with their fossil-fuel counterparts, and it is important to identify biorefinery concepts with high economic performance. For evaluating early-stage biorefinery concepts, one needs to consider not only the technical performance and process costs but also the economic performance of the full supply chain and the impacts on feedstock and product markets. This article presents and demonstrates a conceptual interdisciplinary framework that can constitute the basis for evaluations of the full supply-chain performance of biorefinery concepts. This framework considers the competition for biomass across sectors, assumes exogenous end-use product demand, and incorporates various geographical and technical constraints. The framework is demonstrated empirically through a case study of a sawmill-integrated biorefinery producing liquefied biomethane from forestry and forest industry residues. The case study results illustrate that acknowledging biomass market effects in the supply chain evaluation implies changes in both biomass prices and the allocation of biomass across sectors. The proposed framework should facilitate the identification of biorefinery concepts with a high economic performance which are robust to feedstock price changes caused by the increase in biomass demand.

Many classic visual monocular SLAM systems have been developed over the past decades, however, most of them will fail when dynamic scenarios dominate. DM-SLAM is proposed for handling dynamic objects in environments based on ORB-SLAM. The article mainly concentrates on two aspects. Firstly, DLRSAC is proposed to extract static features from the dynamic scene based on awareness of nature difference between motion and static, which is integrated into initialization of DM-SLAM. Secondly, we design candidate map points selection mechanism based on neighborhood mutual exclusion to balance the accuracy of tracking camera pose and system robustness in motion scenes. Finally, we conduct experiments in the public dataset and compare DM-SLAM with ORB-SLAM. The experiments verify the superiority of the DM-SLAM.

As a special class of “green” elastomers, thermoplastic vulcanizates (TPVs) have been widely used in industries due to the combination of the excellent resilience of conventional elastomers and the easy recyclability of thermoplastics. Here, the morphology evolution of TPVs based on polyamide 6/ethylene-propylene-diene rubber (PA6/EPDM) blends was investigated by varying the content of the curing agent, phenolic resin (PF). With the incorporation of 6 wt% PF, the gel content of the EPDM phase reaches a high value of 49.6wt% and a typical sea-island structure is formed with EPDM domain in a micro-nano size. The dynamic rheology behaviors of TPVs showed that with the curing degree of EPDM phase increasing, a denser network of EPDM particles is formed in PA6 matrix. Also, a lower crystal degree and crystal peak temperature are observed, indicating that the presence of a growth restriction of PA6 crystal plate induced by a thinner plastic layer between the adjacent EPDM particles. However, the crystal form of PA6 is not changed with the increasing curing degree of the EPDM phase. This study provides an effective strategy to realize a new kind of TPVs, which can be easily introduced into industrial applications.

Mini-bioreactor systems enabling automatized operation of numerous parallel cultivations have been used to accelerate and optimize bioprocess development. As implementation of fed-batch conditions, multiple options of process control and sample analysis are possible, these systems represent valuable screening tools for large-scale production. However, the dynamic behavior of cultivations has not yet been considered regarding data evaluation and decision making during high-throughput screening in mini-bioreactors. In this study, the characterization of Saccharomyces cerevisiae AH22 secreting recombinant endopolygalacturonase is performed in 48 parallel fed-batch cultivations regarding 16 experimental conditions. Automated parallel process control, frequent sampling and analysis were implemented. Data-driven multivariate methods were developed to allow for fast, automated decision making as well as online predictive data analysis regarding endopolygalacturonase production. Using dynamic process information, a cultivation with abnormal behavior could be detected by principal component analysis as well as two clusters of similarly behaving cultivations, later classified according to the feeding rate. By decision tree analysis, cultivation conditions leading to an optimal recombinant product formation could be identified automatically. The developed method is easily adaptable and suitable for automatized process development reducing the experimental times and costs.

Comparison between hydraulic and hydrologic computational methods is conducted in this study, regarding prismatic open channels under unsteady subcritical flow conditions. One-dimensional unsteady flow continuity and momentum equations are solved using explicit and implicit finite difference schemes for a symmetrical trapezoidal cross section, where the flow discharge and depth are the dependent variables. The results have been compared to those derived from Muskingum-Cunge hydraulic/hydrologic method as well as the commercial software HEC-RAS. The results from explicit and implicit code compare well to those from commercial software and hydraulic/hydrologic methods for long prismatic channels, thus directing the hydraulic engineer to quick preliminary design of prismatic open channels for unsteady flow with satisfactory accuracy.

Stress relaxation tests in cantilever bending were performed on the C7025 and C7035 alloys at 298K and 393K，respectively. The effect of stress-relief treatments on stress relaxation properties was investigated. The structural changes associated with the stress relaxation process were examined using transmission electron microscope. The stress relaxation curve fits well to empirical formula σ*=[Kˊln(t+α₀)+C]^-n for stress relaxation. The curves can be split into two stages. The stress relax quickly in the first stage, slows down in the second stage, and tends to be a certain limit value after a long time. The curve and microstructure reveals that the C7035 alloy has a lower rate of stress relaxation and a higher anti-stress relaxation capacity than the C7025. The first reason is that the movement of vacancies required by spinodal decomposition is inhibited, and the quantity of cobalt -containing vacancies decreases dramatically in the C7035 alloy. The other reason is that the precipitated phases became uniformly diffused in the C7035 alloy. The precipitate phase uniformly distributes in the grain boundaries and the matrix, during the relaxed condition, and thus the dislocations moving is blocked by the precipitates.

The effects of psychological pressure on perceiving the height of a jump bar just before starting a high jump run was investigated. University students (N = 14) training for a high jump event performed 15 trials (3 practice, 6 pressure, and 6 non-pressure) in counterbalanced order in their daily practice environment. The height of the bar was judged as significantly higher on pressure trials compared to non-pressure trials. A regression analysis indicated that participants who reported increased subjective perceived pressure tended to judge the bar to be higher. There was no significant difference between pressure and non-pressure trials for the performance index, defined as the success rate. This study provides the first evidence that environmental perceptions prior to executing a motor task under pressure may make performance of the task appear to be more difficult.

Based on the fractional order of nonlinear system for love model with a periodic function as an external force, analyzed the characteristics of the chaotic dynamic in this study. The relationship between the chaotic dynamic of the fractional-love model with the external force and the fractional-order system was analyzed when the parameters are fixed. Further, we also studied the relationship between the chaotic systemic dynamic and the parameters when the fractional-order system is fixed. The results show that when the parameters are fixed, the fractional-order system exhibited segmented chaotic states for the different fractional orders of the system. When fixed the fractional-order system, the system exhibited the periodic and chaotic states as parameter changes.

Dynamic laser speckle is applied as a reliable sensor of activity in all sort of material. Traditional applications are based on a time rate that is usually higher than 10 frames-per-second (FPS). Even in drying processes, where there is a high activity in the first moments after the painting and a slow activity after some minutes or hours, the process is based on the acquisition of images in a time rate that is the same in both moments of high and low activity. In this work, we present an alternative approach to follow the drying of paint and the other processes related to restauration of paintings that takes long-term to reduce the activity. We illuminated, using three different wavelength lasers, an accelerator (Cyclododecane) and a varnish used in restauration of paintings and monitor them at long-term drying using an alternative fps, comparing the results to the traditional method. The work also presents a way to do the monitoring using a portable equipment. The results present the feasibility to use the portable device and show the improvement in the sensitivity of the dynamic laser speckle to sense long-term process regarding the drying of Cyclododecane and Varnish used in restauration.

Visual inertial SLAM algorithms enable robots to autonomously explore and navigate in unknown scenes. However, most of the current SLAM systems highly rely on static environment assumptions, which fails in the exsitence of motional objects in the real environment. To improve the robustness and localization accuracy of SLAM systems in dynamic scenes, this paper proposes a visual-inertial SLAM framework that fuses semantic and geometric information, called DA-VINS. First, this paper presents a dynamic object classification method based on feature’s current motion state, which obtains temporary static features in the environment. Secondly, a features dynamics check module based on IMU prior and adjacent frame’s geometry constraint is designed to calculate dynamic factors. It also verifies the classification results of temporary static features. Finally, a dynamic adaptive bundle adjustment module based on the features’ dynamic factors is designed to adjust the weights of features in nonlinear optimization. We evaluated our method in public and our dataset. The results show that D-VINS is one of the most real-time, accurate, and robust systems in dynamic scenes.

Three-point shooting plays an important role in determining the outcome of the basketball games, and could be relevant for player selection. However, there has been little research into the relationship between basketball players' physical capacities, metabolic capacities and three-point shooting accuracy, particularly among female players. The aim of this study was to examine the relationship between physical capacities, metabolic capacities and dynamic three-point shooting accuracy in female professional basketball players. Twelve female professional basketball players from the Women’s Chinese Basketball Association (WCBA) league (age: 19.04±1.31 years, height: 181.33±4.90cm, playing experience: 7.83±1.7 years) were recruited for this study. Pearson correlations and multiple linear regression analysis were run to assess the relationship between physical capacities, metabolic capacities and dynamic three-point shooting. Results showed that coordination, balance, core strength and relative average power were positively correlated with the three-point shooting accuracy (r>0.58, P<0.05), while no other variables showed significant correlations. The current study suggests that coaching staff should consider coordination, balance, core strength and anaerobic capacities when selecting players as well as in their training periodization if three-point shooting accuracy is considered relevant.

Physical rehabilitation aims to help people recover their mobility and strength after an injury or illness. One way to evaluate progress in rehabilitation is through isokinetic prototype tests that describe the dynamic characteristics of an isokinetic leg extension device for rehabilitation and control action. These tests use an isokinetic system to assess muscle strength and performance in a patient during isometric or isokinetic contraction. An experimental prototype allows the performance of the device to be evaluated in a controlled environment prior to use by the patient. In order to achieve physical recovery from musculoskeletal injuries in the lower limbs and achieve the reintegration of the affected subject into society as an independent and autonomous individual in their daily activities, a control model is presented that introduces a medical isokinetic rehabilitation protocol, where the element that allows carrying out such protocol consists of a magnetic particle brake whose control action is strongly influenced by the dynamics of the system when in contact with the end user, specifically the patient's legs in the stretch from the knee to the ankle. The results of these tests are valuable for health professionals seeking to measure their patient’s progress during the rehabilitation process and determine when it is safe and appropriate to advance in their treatment.

Positive invariant set is an important concept of dynamic systems. The purpose of this paper is to study the sufficient and necessary conditions that the set of ellipsoids and the Lorenz cone are positive invariant sets of discrete time systems. By means of nonlinear programming and induced norm, the problem of positive invariance is formulated as an optimization problem, and the equivalent dual form optimization is also presented using the dual optimization method. Our results provide more alternative methods for determining the positive invariance of quadratic form convex sets from the point of view of optimization and dual optimization. The effectiveness of this method is demonstrated by numerical examples.

The modeling of tilting-pad journal and thrust bearings presents a level of complexity beyond that of bearings of fixed-arc geometry, particularly with regard to dynamic influences. With tilting-pad bearings, the theory surrounding the fluid film must be complemented with representative modeling of the pad dynamics. What has been recognized in recent decades has been the significance of the pad support, in particular the flexibility of the pivot region of the pad. The typical model for including the stiffness of the pivot has been based on Hertzian contact theory. Some researchers have been noting that the Hertzian theory does not permit sufficient flexibility in the pivot region. It is suggested that the contact mechanics at the pivot would be better represented as a pairing of rough surfaces. The modeling used here is based on a statistical asperity micro-contact theory for rough-surface line contact that has been extended to include contact stiffness. This model has been applied to the determination of the effective dynamic properties of tilting-pad bearings. The results show that pivot stiffness can be as low as one-third the stiffness determined by Hertzian theory. Comparison to published experimental results confirms the significance of the rough-surface modeling, particularly for the line contacts associated with rocker-back tilting pads.

The dynamic and surface manipulation of the M13 bacteriophage meeting application demands enable a pathway to design efficient applications with high selectivity and responsivity rate. Herein, we report the role of the M13 bacteriophage thin film layer deposited on an optical nanostructure involving gold nanoparticles/SiO2/Si and its influence on optical and geometrical properties. The thickness of the M13 phage layer was either controlled by varying the concentration or humidity exposure levels, and optical studies were conducted. We designed a standard and dynamic model based upon three-dimensional finite-difference time-domain (3D FDTD) simulations distinguishing the necessity of each model under variable conditions. As seen from the experiments, the origin of respective peak wavelength positions is addressed in detail with the help of simulations. The importance of the dynamic model was noted when humidity-based experiments were conducted. Inexpensive, multi-wavelength optical characteristics from a single structure, reproducibility, and reversible properties are significant advantages of involving M13 bacteriophage. We believe this work will provide fundamental insight into understanding and interpreting the geometrical and optical properties of the nanostructures involving M13 bacteriophage.

In many countries, governments have implemented non-pharmaceutical techniques to limit COVID-19 transmission. Restricting human mobility is one of the most common interventions, including lockdown, travel restrictions, working from home, etc. However, due to the strong transmission ability of the virus variants, further rounds of interventions, including a strict lockdown, are not considered as effective as expected. The paper aims to understand how the lockdown policy and pandemics changed human mobility in the real scenario. Here we focus on understanding the mobility changes caused by compliance with restrictions and risk perceptions, using the mobility index from the Google report during three strict lockdown periods in Leeds, the largest city in the county of West Yorkshire, England from March 2020 to March 2021. The research proposed the time-varying z-scores and Principal Component Analysis (PCA) to simulate how local people dynamically process and perceive health risk based on multi-dimensional daily COVID-19 reports first. Further modelling highlights exponentially increasing policy non-compliance through the duration of lockdown, probably attributable to factors such as mental anxiety and economic pressures. Finally, the proposed nonlinear regression model examines the mobility changes caused by the population's dynamic risk perceptions and lockdown duration. The case study at Leeds fits data well and shows that the third lockdown policy took effect much slower than the first. At the same time, the negative impact of the epidemic on population mobility decayed 40% in the third lockdown period in contrast with the first lockdown. The risk perception estimation methods could reflect that the local population became increasingly accustomed to the COVID-19 situation, and local people rationally evaluated the risks of COVID in the third lockdown period. The results prove that simulated risk perceptions and policy decay could explain urban mobility behaviour during the mobility well during lockdown periods, which could be a reference for future decision-making processes.

Understanding and evaluating urban investment environment is essential for effectively improving the efficiency of resource allocation between cities and promoting overall development of the regional economy. This paper takes 15 node cities on maritime Silk Road covered by the “Belt and Road” as the research object, establishes a dynamic evaluation index system for investment environment, and uses projection pursuit cluster to analyze and evaluate the investment environment of the cities. It is found that the investment environment potential of a city is directly related to the level of social development, economic development, and the degree of opening to the outside world. It is recommended that node cities should seize the important opportunity of the construction of the Maritime Silk Road, introduce world-wide human, financial and material resources to promote regional resources allocation and flow, and continuously improve and upgrade the investment environment quality.

Based on the two-node Euler-Bernoulli beam, the tower system is discretized by finite element method, and the cubic Hermite polynomial is taken as the shape function of the beam element, and the structural characteristic matrix of the tower system is calculated, and the wind turbine-nacelle-tower multi-degree of freedom is established Finite element numerical model. The aerodynamic load calculation formula for any nacelle attitude angle is deduced. The influence of the vibration feedback of the flexible tower on the aerodynamic load of the wind turbine is studied. The results show that when the rigidity of the tower is large, the impact of tower vibration feedback on the aeroelastic load of the wind turbine is small. For a tower system with greater flexibility, the time-varying feedback of wind-induced vibration will cause greater aeroelastic load changes, especially the overturning moment of the tower top, which will cause a greater impact on the dynamic behavior of the tower in the downwind and crosswind directions. As the flexibility of the tower system increases, the interaction between tower vibration and aerodynamic load is gradually increasing. Taking the impact of the flexible tower on the aeroelastic load of the wind turbine into account, on the one hand, helps to predict the wind more accurately. The aerodynamic load of the wind turbine improves the efficiency of wind energy utilization. On the other hand, it can more accurately analyze the dynamic behavior of the flexible structure of the wind turbine, which is extremely beneficial to the structural optimization design of the wind turbine.

This article addresses the generic dynamic decision problem of how to achieve sustained market growth by increasing two interdependent organizational resources needed (1) to increase and (2) to sustain demand. The speed and costs of increasing each resource are different. Failure to account for this difference has been reported to lead to policies that drive a quick increase of demand followed by decline. Three generic policies derived from the literature have been implemented in a system dynamics model. Simulation shows that all three policies can generate sustained exponential growth but differ in performance. These results suggest that even policies which risk generating overshoot and collapse can avoid it. This poses two questions for further research: (1) what is the reasoning of human decision-makers when choosing between these policies and (2) how can the important but easily overlooked features of such decision situations be made sufficiently salient to be accounted for?

Trajectory Optimization (TO) is the sequence of processes that are considered in order to produce the best path that mends the overall performance or reduces the consumption of the resources where the restriction system remains maintained. In this survey, an inclusive review of the latest advancements in modeling and optimization of trajectory generation in robotic applications will be discussed broadly. In recent times, numerous studies have employed optimal control techniques involving direct and indirect methods in order to convert the authentic Trajectory Optimization problem into a constrained parameter optimization problem. Moreover, a huge variety of optimization algorithms such as Genetic Algorithms (GA), Simulated Annealing (SA), Sequential Quadratic Programming (SQP), and Particle Swarm Optimization (PSO) are used aiming to find the optimal solutions for trajectory planning. It is observable that, minimizing the jerk, energy consumption, and execution time among the most widely used design objectives, on the other hand, the robot’s joints configurations and the motor torques are the most used design variables. This paper aims to review the fundamental techniques and their coincident robotic applications in the field of trajectory optimization aiming to afford some steering for related researchers.

With the increasingly stringent airworthiness standards, the noise generated during the rotorcraft flight is gradually attracting people’s attention. It widely operated helicopters at low altitudes because of their maneuverability. The way to reduce the noise caused by the complex airflow of the helicopter rotor system has progressively become a hot topic for researchers. Using a hybrid acoustic analysis method, this paper investigates the improvement of the noise and thrust of the helicopter’s tail rotor through the tail rotor structural parameters. For the basic model, the turbulence simulation is performed using an incompressible detached eddy simulation (DES) method, and the Lighthill acoustic analog equation is calculated using the finite element method (FEM). We verified the accuracy of the method through wind tunnel tests. We chose a series of structural parameters for sound simulation and fluid simulation calculations. The results indicate that the modified tail rotor noise reduced by 16.5 dBA and the total thrust increased by 19.9% from the prototype model. This work can enhance the duct tail rotor design to improve aerodynamic and aeroacoustic performance.

Offshore vessels (OVs) often requires precise station-keeping and some vessels, for example, vessel involves in geotechnical drilling generally use Spread Mooring (SM) or Dynamic Positioning (DP) systems. Most of these vessels are equipped with both systems to cover all ranges of water depths. However, determining which systems to use for a particular operational scenario depends on many factors and requires significant balancing in terms of cost-benefit. Therefore, this research aims to develop a platform that will determine the cost factors for both the SM and DP station keeping systems. Operational information and cost data are collected for several field operations, and Artificial Neural Networks (ANN) is trained using those data samples. After that, the trained ANN is used to predict the components of cost for any given environmental situation, fieldwork duration and water depth. Later, the total cost is investigated against water depth for both DP and SM systems to determine the most cost-effective option. The results are validated using two operational scenarios for a specific geotechnical vessel. This decision-making algorithm can be further developed by adding up more operational data for various vessels and can be applied in the development of sustainable decision-making business models for OVs operators.

In this study, a dynamic mixture copula is used to estimate the marginal expected shortfall in the South African insurance sector. While other studies assumed nonlinear dependence to be static over time, our model capture time-varying nonlinear dependence between institutions and the market. In order to capture time-varying nonlinear dependence, the generalized autoregressive score (GAS) is used to model the dynamic copula parameters. Furthermore, our study implements a ranking that expresses to what degree individual insurers are systemically important in South Africa. We use daily stock return of five South African insurers listed in the Johannesburg Stock Exchange (JSE) from November 13, 2007 to June 15, 2020. We find that Sanlam and Discovery contribute the most to systemic risk, while Santam is found to be the least contributor to the overall systemic risk in the South African insurance sector. Our findings would be of paramount importance for the South African regulators as they would be informed that not only banks are systemically important, but some insurers also are systemically important financial institutions. Hence, stricter regulation of these institutions in the form of higher capital and loss absorbency requirements could be required based on the individual business activities undertaken by the company.

The technique of superposition of motions in the space of Lagrange variables is described, which allows us to obtain the equations of combined motion by replacing the Lagrange variables of superimposed (external) motion with Euler variables of nested (internal) motion. The components of velocity and acceleration in the combined motion obtained as a result of differentiating the equations of motion in time coincide with the results of vector addition of the velocities and accelerations of the particles involved in the superimposed motions at each moment of time. Examples of motion and superposition descriptions for absolutely solid and deformable bodies with equations for the main kinematic characteristics of motion, including for robot manipulators with three independent drives, pressing with torsion, bending with tension, and cross– helical rolling, are given. For example, given the fragment of calculation of forces in the kinematic pairs shown the advantages of the description of motion in Lagrangian form for the dynamic analysis of lever mechanisms, allows to determine the required external exposure when performing the energy conservation law at any time in any part of the mechanism.

Human civilizations are under enormous threats due to the outbreak of novel coronavirus (COVID-19) originated from Wuhan, China. The asymptomatic carriers are the potential spreads of this novel virus. Since, guaranteed antiviral treatments have not been available in the market so far, it is really challenging to fight against this contagious disease. To save the living mankind, it is urgent to know more about how the virus transmits itself from one to another quite rapidly and how we can predict future infections. Scientists and Researchers are working hard in investigating to understand its high infection rate and transmission process. One possible way to know is to use our existing COVID-19 infection data and prepare a useful model to predict the future trend. Mathematical modelling is very useful to understand the basic principle of COVID-19 transmission and provide necessary guidelines for future prediction. Here, we have reviewed 9 distinct commonly used models based on Mathematical implementations for COVID-19 transmission and dig into the deep head to head comparison of each model. Finally, we have discussed interesting key behaviour of each model, relevant upcoming important issues, challenges and future directions.

Dynamic visualizations have been developed to exchange information that transforms over time across a broad range of professional and academic contexts. However, these visual tools may impose substantial demands on the learner’s cognitive resources that are very limited in current knowledge. Cognitive load theory has been used to improve learning from dynamic visualizations by providing certain design techniques to manage learner cognitive load without adding any oral/written explanations. This systematic review examined a series of experimental studies assessing the roles of these design techniques in learning tactical scenes of play through dynamic visualizations. Electronic databases PubMed and Google Scholar were used to search relevant articles. Eleven studies were eventually included for the systematic review based on the eligibility criteria. The present review revealed that adapting design techniques to the level of learners’ expertise, type of depicted knowledge, and level of content complexity is a crucial part of effective learning.

The sudden pervasive of severe acute respiratory syndrome Covid-19 has been leading the universe into a prominent crisis. It has influenced each zone, for example, industrial area, horticultural zone, Public transportation, economic zone, and so on. So as to see how Covid-19 affected the globe, we conducted an investigation characterizing the effects of the pandemic over the world using Machine Learning (ML) method. Prediction is a typical data science exercise that helps the administration with function planning, objective setting, and anomaly detection. We propose an additive regression model with interpretable parameters that can be naturally balanced by experts with domain intuition about the time series. We focus on global data beginning from 22^nd January 2020, till 26^th April 2020 and performed dynamic map visualization of Covid-19 expansion globally by date wise and predicting the spread of virus on all countries and continents. The major advantages of this work include accurate analysis of country-wise as well as province/state-wise confirmed cases, recovered cases, deaths, prediction of pandemic viral attack and how far it is expanding globally.

This paper presents a physical and mathematical model that has been developed in the framework of the approach used in the computational mechanics of materials. The model is designed to enable the study of the patterns of deformation and fracture of ceramic composites with a transformation-hardened matrix that are obtained by additive technologies at the mesoscopic and macroscopic levels under intense dynamic loading. The influence of the loading rate on the formation of the fracture and energy dissipation fronts for composite materials, based on the Al2O3 20%ZrO2 system, is shown. Nonlinear effects under intense dynamic loading in the considered composites are associated with the processes of self-organization of structural fragments at the mesoscopic level, as well as the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

Static (SLS) and dynamic (DLS) light scattering techniques are assessed for their capacity to detect colloidal particles with diameters between d = 0.1 and 0.8 µm at very low concentrations in seawater. The detection limit of the apparatus was determined using model monodisperse spherical polystyrene latex particles with diameters 0.2 µm and 0.5 µm. It is shown that the concentration and size of colloids can be determined down to about 10^-6 g/L. Seawater obtained from different locations in western Europe was characterized using light scattering. It was found that seawater filtered through 0.45 µm pore size membrane filters was within the experimental error the same as that of ultrapure Milli-Q water containing the same amount of sea salt and no colloids could be detected with DLS. When the seawater was filtered through 0.8 µm pore size filters, colloidal particles were detected. The measurements show that the concentration of colloids in the seawater samples is not higher than 10^-6 g/L and that they have an average diameter of about 0.6 µm. We stress that these particles are not necessarily nanoplastics.

A regularization approach to model selection, within a generalized HJM framework, is introduced which learns the closest arbitrage-free model to a prespecified factor model. This optimization problem is represented as the limit of a one-parameter family of computationally tractable penalized model selection tasks. General theoretical results are derived and then specialized to affine term-structure models where new types of arbitrage-free machine learning models for the forward-rate curve are estimated numerically and compared to classical short-rate and the dynamic Nelson-Siegel factor models.

In this age of Facebook, Instagram, and Twitter, there is rapidly growing interest in understanding network-enabled opinion dynamics in large groups of autonomous agents. The phenomena of opinion polarization, the spread of propaganda and fake news, and the manipulation of sentiment is of interest to large numbers of organizations and people. Whether it is the more nefarious players such as foreign governments that are attempting to sway elections or it is more open and above board, such as researchers who want to make large groups of people aware of helpful innovations, what is at stake is often significant. In this paper, we review opinion dynamics including the extensions of many classical models as well as some new models that deepen understanding. For example, we look at models that track the evolution of an individual’s power, that include noise, and that feature sequentially dependent topics, to name a few. While the first papers studying opinion dynamics appeared over 60 years ago, there is still a great deal of room for innovation and exploration. We believe that the political climate and the extraordinary (even unprecedented) events in the sphere of politics in the last few years will inspire new interest and new ideas. It is our aim to help those interested researchers understand what has already been explored in a significant portion of the field of opinion dynamics. We believe that in doing this, it will become clear that there is still much to be done.

The Oil reservoirs with low permeability account for a large proportion in the world, they surpass half of the total number of the oil reservoirs in China, it is important to exploit this kind of reservoir effectively. The exploitive results of these reservoir using normal water flooding methods are very poor because of the thine pores, bad connections and so on. However, these problems can be well solved by applying gas injection techniques. In this paper, the effects on the recovery effects exerted by the injection parameters such as the oxygen content in the injected air, the injection speed etc. were studied by several experiments using independently designed equipments aiming at one low permeable sandstone reservoir in China. Several conclusions were made from the experiment results: the best recovery effects can be achieved by injecting the oxygen reduced air with 8% of oxygen at the speed of 0.3ml/min (7.41×10-4PV/min) using the methods of injecting the air slugs and the foaming agent slugs alternately; the best oxidation time of the oil was 168 hours and the final oil recovery could be enhanced by 26.5% in this method. It was also showed by the experiments that the larger the permeability ratio is, the larger the recovery factor will be increased. At last, several equations about relationships between the EOR and the air injection parameters were revealed according to the results of the experiments which may offer some references to the LTO process mechanisms study in the similar oil reservoir.

Ubiquitin-specific protease 14 (USP14) is a member of the Deubiquitinating enzymes (DUBs) involved in disrupting the regulation of the ubiquitin-proteasome system, responsible for the degradation of impaired and misfolded proteins which is an essential mechanism in eukaryotic cells. The involvement of USP14 in cancer progression and neurodegenerative disorders has been reported. Thereof USP14 is a prime therapeutic target; hence, designing efficacious inhibitors of USP14 is central in curbing these conditions. Herein, we relied on structural bioinformatics methods incorporating molecular docking, Molecular Mechanics Generalized Born Surface Area (MM-GBSA), Molecular dynamics simulation (MD simulation) and ADME to identify potential allosteric USP14 inhibitors. A library of over 733 compounds from the PubChem repository with >90% match to the IU1 chemical structure was screened in a multi-step framework to attain prospective drug-like inhibitors. Two potential lead compounds (CID 43013232 and CID 112370349) were shown to record better binding affinity compared to IU1, but with subtle difference to IU1-47, a 10-fold potent compound when compared to IU1. The stability of the lead molecules complexed with USP14 was studied via MD simulations. The molecules were found to be stable within the binding site throughout the 50ns simulation time. Moreover, the protein-ligand interactions across the simulation run time suggest Phe331, Tyr476, and Gln197 as crucial residues for USP14 inhibition. Furthermore, in silico pharmacological evaluation revealed the lead compounds as pharmacological sound molecules. Overall, the methods deployed in this study revealed two novel candidates that may show selective inhibitory activity against USP14, which could be exploited to produce potent and harmless USP14 inhibitors.

This paper examines the dynamic dependence structure of crude oil and East Asian stock markets at multiple frequencies using wavelet and copulas. We also investigate risk management implications and diversification benefits of oil-stock portfolios by calculating and comparing risk and tail risk hedging performance. Our results provide strong evidence of time-varying dependence and asymmetric tail dependence between crude oil and East Asian stock markets at different frequencies. The level and fluctuation of their dependencies increase as time scale increases. Furthermore, we find the time-varying hedging benefits differ at investment horizons and reduced over the long run.

Injuries to the ligaments of the knee are extremely common among athletes who participate in high-risk sports, or any sport that requires frequent cutting motions, jumping, or contact. In order to determine the best way to heal these injuries, it is important to understand not just the pathology of the injury, but also the biomechanical factors that are affected, including stability and steadiness. While many studies have been done to examine the stability of healthy knees, there is little to no existing literature on stability of knees afflicted by injury. In order to surpass this obstacle, static steadiness and dynamic stability data was collected using the Lockhart Monitor phone application and Xsens accelerometers, respectively, both before and after completion of a course of physical therapy in a patient with a grade 2 medial collateral ligament (MCL) tear. These results were then used to determine the degree to which the prescribed physical therapy protocol was effective in healing the MCL, which can be useful for tweaking the individual protocol for future conservative treatment and management of the injury.

This paper presents the results of investigations of the effects of hot deformation parameters in compression investigation on the austenite grain size in HSLA steel (0.16% C, 0.037% Nb, 0.004% Ti, 0.0098% N). The axisymmetric compression investigations were performed on cylindrical investigation specimens of d=1.2 using the Gleeble 3800 simulator. The strain rate=1s^-1÷15.9s^-1 and strain degree ε=1.2. Before deformation, the research specimens were austenitized at TA = 1100 ÷ 1250 °C. Metallographic observations of the primary austenite grains were conducted with an optical microscope, while the structure of dynamically recrystallized austenite, inherited by martensite, was examined by EBSD technique using a scanning electron microscope. Based on the analysis of investigation results, it was found that the size of dynamically recrystallized austenite grains in HSLA steel were clearly affected by hot compression parameters. In contrast, no significant impact of austenitising temperature on their size was found.

In this paper, the physical station of space network was extended in time dimension by combining the train diagram information and station technical operation standard time. At the same time, the topology of railway space-time network which considered the secondary operation process of train was constructed and an improved A* algorithm based on car flow routing was proposed to generate feasible path sets. On this basis, a dynamic car flow organization optimization model was built to simulate the railway car flow organization process under abnormal conditions, and the results of solving the model could be used to obtain the real-time quantity of cars at each station.This paper can identify the dynamic bottleneck by comparing the real-time quantity of cars with the maximum quantity of cars at the station. Finally, the feasibility of this method was analyzed and verified by a case.

Opportunistic routing has emerged as one of the prominent solutions for efficient data delivery in ad hoc networks especially in highly dynamic scenarios. Opportunistic routing uses the broadcasting nature of the wireless medium to increase the number of potential forwarding nodes in the network, thereby improving the delivery rate. But most of the proposed opportunistic routing protocols suffer from increased duplicate data forwarding at the intermediate nodes in the network which leads to increase in traffic and reduced efficiency. We propose a novel method which uses acknowledgements for controlling the data forwarding by intermediate nodes and thereby eliminating most of the duplicate forwarding in the network. Simulation results show that our proposed method is much more efficient that all the major existing opportunistic protocols.

The aim of this expository article is to present recent developments in the centuries-old discussion on the interrelations between several types of domination in graphs. However, the novelty even more prominent in the newly discovered simplified presentations of several older results. Domination can be seen as arising from real-world application and extracting classical results as first described by this article.The main part of this article, concerning a new domination and older one, is presented in a narrative that answers two classical questions: (i) To what extend must closing set be dominating? (ii) How strong is the assumption of domination of a closing set? In a addition, we give an overview of the results concerning domination. The problem asks how small can a subset of vertices be and contain no edges or, more generally how can small a subset of vertices be and contain other ones. Our work was as elegant as it was unexpected being a departure from the tried and true methods of this theory that had dominated the field for one fifth a century. This expository article covers all previous definitions. The inability of previous definitions in solving even one case of real-world problems due to the lack of simultaneous attentions to the worthy both of vertices and edges causing us to make the new one. The concept of domination in a variety of graphs models such as crisp, weighted and fuzzy, has been in a spotlight. We turn our attention to sets of vertices in a fuzzy graph that are so close to all vertices, in a variety of ways, and study minimum such sets and their cardinality. A natural way to introduce and motivate our subject is to view it as a real-world problem. In its most elementary form, we consider the problem of reducing waste of time in transport planning. Our goal here is to first describe the previous definitions and the results, and then to provide an overview of the flows ideas in their articles. The final outcome of this article is twofold: (i) Solving the problem of reducing waste of time in transport planning at static state; (ii) Solving and having a gentle discussions on problem of reducing waste of time in transport planning at dynamic state. Finally, we discuss the results concerning holding domination that are independent of fuzzy graphs. We close with a list of currently open problems related to this subject. Most of our exposition assumes only familiarity with basic linear algebra, polynomials, fuzzy graph theory and graph theory.

Abstract: The Inconel 625 is a nickel-based alloy has been widely used in the high-temperature application. The Inconel 625 exhibits unstable plastic flow at elevated temperature characterized by serrated yielding, known as Portevin-Le Chatelier effect. The aim of this work is to evaluate the mechanical properties at high temperatures of the Inconel 625. The tensile tests were performed in the temperature range of room temperature until 1000 °C and strain rate of 2x10^-4 to 2x10^-3 s^-1. The creep tests were performed in the temperature range of 600-700 °C, in the stress range of 500-600 MPa in a constant load mode. The surface fracture was observed by optical and scanning electron microscopy. Serrated stress-strain behavior was observed in the curves obtained at 200 to 700 °C, which was associated with the dynamic strain aging effect. The yield strength and the elongation values show an anomalous behavior as a function of the test temperature. An intergranular cracking was observed specimen tensile tested at 500 °C that can be attributed to the decohesion of the carbides along the grain boundaries. The fracture surface of the specimen tensile tested at 700 °C showed the predominance of transgranular cracking with tear dimples with a parabolic shape.

This paper utilizes dynamic panel threshold technology to conduct a nonlinear test on the direct effect between environmental regulation and economic fluctuations and the effect of industrial structure upgrading by taking 35 industrial sectors in China from 2003 to 2016 . The research has found that there is an inverted "U" relationship between environmental regulation and economic fluctuations, with the enhancement of environmental regulations, the economic fluctuation increases first and then decreases. The cross-terms of environmental regulation and industrial structure rationalization or industrial structure upgrading are significantly negative, which indicates that the enhancement of environmental regulation is conducive to promoting industrial structure upgrading and reducing the economic fluctuations. While the rationalization factors of industrial structure and advanced industrial structure are significantly negative, indicating that both forms of industrial structure upgrading are conducive to reducing the economic fluctuations. Environmental regulation has technical innovation thresholds for industrial structure upgrading and economic fluctuations, but there are no human capital or FDI thresholds. In the rationalization model of industrial structure, there is a nonlinear "U" relationship between environmental regulation and economic fluctuations when the proportion of scientific research expenditure is more than 1.35%. With the enhancement of environmental regulation, the economic fluctuation reduces first and then increases, and the corresponding inflection point value is 2.398% of the environmental regulation level. At the same time, the environmental regulation can indirectly reduce economic fluctuations by pushing down the industrial structure upgrades. In the advanced model of industrial structure, there is a “U” relationship between environmental regulation and economic fluctuation when the proportion of scientific research expenditure is greater than 1.26%. With continuous enhancement of environmental regulation, the economic fluctuation reduces first and then increases. The corresponding inflection point value is 1.78% of the environmental regulation level, and environmental regulation can indirectly reduce economic fluctuations by promoting the industrial structure at the same time.