Computational simulations of three-dimensional flow around a NACA 0018 wing with an aspect ratio of AR=5 are carried out using the Unsteady Reynolds-Averaged Navier-Stokes (URANS) equations with the Shear-Stress Transport turbulence model closure. Simulations were performed to capture the aerodynamic stall hysteresis using a developed Pseudo-Transient Continuation (PTC) method based on a dual time step approach in the CFD code OpenFOAM. The flow was characterized by an incompressible Mach number of M=0.12 and a moderate Reynolds number Re=0.67×10^6. The results obtained indicate the presence of a noticeable aerodynamic hysteresis in the static dependencies of the force and moment coefficients, as well as the manifestation of bi-stable flow separation patterns, accompanied by the development of asymmetry in the stall zone. The URANS simulation results are in good agreement with the experimental data obtained for the NACA 0018 finite aspect ratio wing from the low-speed wind tunnel under the same test conditions. A new phenomenological bifurcation model of aerodynamic stall hysteresis under static and dynamic conditions is formulated, which is proven to be able to closely match the experimental data.

The dual-station Interferometric Synthetic Aperture Radar (InSAR) system can overcome the physical limitations imposed by the baseline of single-station dual-antenna InSAR. It provides greater flexibility and can enhance elevation measurement accuracy through a well-designed baseline configuration.Unmanned aerial vehicles (UAV) equipped with dual-station InSAR, with relatively low cost and high flexibility, are useful for mapping and land resource exploration. However, due to challenges including spatiotemporal synchronization and motion errors, there are limited reports on UAV-borne dual-station InSAR. This paper proposes a comprehensive method for processing data from small UAV-borne dual-station InSAR by integrating two-way synchronization chain signals. The proposed method includes compensation for time and phase synchronization errors, trajectory refinement with synchronized chain and Position and Orientation System (POS) data, high-precision dual-station InSAR imaging and interferometric processing. Height inversion results based on the proposed method is also provided, demonstrating the effectiveness of the proposed method and improving interferometric accuracy at calibration points from 0.66 meters to 0.42 meters.

The dual leucine zipper kinase (DLK) alias mitogen-activated protein 3 kinase 12 (MAP3K12) has gained much attention in recent years. DLK belongs to the mixed lineage kinases, characterized by homology to serine/threonine and tyrosine kinase but exerts serine/threonine kinase activity. DLK has been implicated in many diseases including several neurodegenerative diseases, glaucoma, and diabetes mellitus. As a MAP3K, it is generally assumed that DLK becomes phosphorylated and activated by upstream signals and phosphorylates and activates itself, the downstream serine/threonine MAP2K, and ultimately MAPK. In addition, other mechanisms such as protein-protein interactions, proteasomal degradation, dephosphorylation by various phosphatases, palmitoylation, and subcellular localization have been shown to be involved in the regulation of DLK activity or its fine-tuning. In the present review, the diverse mechanisms regulating DLK activity will be summarized to provide a better insight into DLK action and possibly new targets to modulate DLK function.

Pesticides are chemical products are used to protect crops to prevent or eliminate undesirable organisms. Pesticides can contaminate continental waters, air, soil and food products. The presence of pesticide residues must therefore be monitored in water and food using sensitive, reliable and broad-spectrum analytical methods, as there is a huge variety of pesticides. Biosensors are one of the screening methods with great potential for detecting residues below the maximum residue limits. The different sensing principles of enzymatic biosensors for pesticide analysis will be described. This review highlights the great potential of colorimetric, enzymatic biosensors for detecting pesticide residues in water and food. Moreover the development of dual colorimetric and fluorimetric sensors during the past years is presented. These methods are most often based on the enzyme acetylcholinesterase, whose activity is inhibited by pesticides. The different approaches used in the development of these biosensors will be detailed, based on different chemical substrates, fluorophores and nanomaterials. The advantages and disadvantages of each approach will be discussed. Finally, the development prospects for improving these biosensors will be presented.

Measuring pulmonary nodules accurately can help with early diagnosis of lung cancer, which can improve a patient’s chances of survival. Many methods for segmenting nodules have been developed, but they all rely on input from radiologists in the form of a 3D volume of interest (VOI) or use a constant region of interest (ROI) and only consider the presence of nodule within the given VOI. These approaches limit the networks’ ability to detect nodules outside the given VOI and can also include unnecessary structures in the VOI, leading to potentially inaccurate segmentation. In this work, we propose a novel approach for 3D lung nodule segmentation by using 2D region of interest (ROI) inputted from radiologist or computer-aided detection (CADe) system. Particularly, we design a dual-encoder-based hard attention network (DEHA-Net) which incorporates the full slice of thoracic computed tomography scan along with the ROI mask to produce an accurate segmentation mask of lung nodule in the given slice. The proposed architecture exploits the adaptive region of interest (A-ROI) algorithm to automatically investigates the penetration of lung nodule into surrounding slices while eliminating the need to drawing separate ROIs in each slice. Further, the framework performs the multi-view analysis, i.e., in sagittal and coronal views, to improve the segmentation performance. The proposed scheme has been rigorously evaluated on the lung image database consortium and image database resource initiative (LIDC/IDRI) dataset and an extensive analysis of results have been performed. The quantitative analysis shows that the proposed method not only improves the existing state-of-the-art in term of dice score but also, significantly robust against the different types, shape and dimensions of lung nodules.

In this paper a microstrip Wilkinson power divider with a 90^° phase delay at one output port is proposed to obtain circular polarization to feed a dual port RFID antenna. The 90^° phase delay was obtained by embedding an extra quarter wavelength at one port of the Wilkinson power divider. The feeding circuit is then mounted on the ground plane of the microstrip antenna feeding the radiating patch directly through the ground plane and dielectric layer thus reducing any fringing effect and resulting a mechanically compact unit. The proposed feeding method offers better expectation of antenna performance with minimal attenuation and coupling losses. The design process generalizes geometric pa- rameters of the Wilkinson power divider for variable port distances. The paper considers both UK and US RFID center frequencies, 870 MHz and 915 MHz respectively. Numeri- cally computed values for geometric design parameters for both frequencies are tabled as future design tools for port distances varying from 18 mm up to 34 mm at 870 MHz and 17 mm up to 32 mm at 915 MHz. Simulation results indicate a return loss (S11) of -20 dB and -26 dB at 870 MHz and 915 MHz operational frequencies respectively at 270^° angled quarter wavelength.

The kinetics and modeling of dual-wavelength controlled photopolymerization confinement (PC) are presented and measured data are analyzed by analytic formulas and numerical data. The UV-light initiated inhibition effect is strongly monomer-dependent and different monomers have different C=C bond rate constants and conversion efficacy. Without the UV-light, for a given blue-light intensity, higher initiator concentration (C₁₀) and rate constant (k’) lead to higher conversion, as also predicted by analytic formulas, in which the total conversion rate (R_T) is an increasing function of k’R, which is proportional to k[gB₁C₁]^0.5. However, the coupling factor b₁ plays a different role that higher b₁ leads to higher conversion only in the transient regime; whereas higher b₁ leads lower steady-state conversion. For a fixed initiator concentration C₁₀, higher inhibitor concentration (C₂₀) leads to lower conversion due to stronger inhibition effect. However, same conversion reduction was found for the same H-factor of H₀ = [b₁C₁₀ - b₂C₂₀]. Conversion of blue-only are much higher than that of UV-only and UV-blue combined, in which high C₂₀ results a strong reduction of blue-only-conversion, such that the UV-light serves as the turn-off (trigger) mechanism for the purpose of spatial confirmation within the overlap area of UV and blue light. For example, UV-light controlled methacrylate conversion of a glycidyl dimethacrylate resin formulated with a tertiary amine co-initiator, and butyl nitrite, subject to a continuous exposure of a blue light, but an on-off exposure of a UV-light. Finally, we developed a theoretical new finding for the criterion of a good material/candidate governed by a double ratio of light-intensity and concentration, [I₂₀C₂₀.]/[I₁₀C₁₀].

Lung cancer remains the leading cancer killer worldwide. Early diagnosis can effectively increase the patient cure rate but existing diagnostic methods limit early lung cancer diagnosis. Therefore, development of a simple but efficient lung cancer screening method is important to improvement of both the diagnosis rate and the survival rate of lung cancer patients. In this study, ten photosensitive materials with high sensitivity and high specificity were screened accurately to construct a microarray sensor that can rapidly identify six types of lung cancer biomarkers in exhaled breath. Results from hierarchical cluster analysis (HCA), principal component analysis (PCA) and difference maps showed that the classification of the analytes agreed with structure similarity laws. The detection results from parallel experiments and structurally similar analytes, in turn, cluster into a group; the fingerprints of the different analytes have specific response regions. The well-screened sensor chip fabrication workload and cost were both reduced by approximately two thirds, while the microfluidic device sensitivity and stability increased by approximately 1.3 times their corresponding values before optimization. The dual-channel device also offers real-time contrast detection and synchronous parallel detection functions and has potential application prospects for use in extensive screening of high-risk populations for lung cancer.

Rare earth elements (REEs) are a type of new material resources, which have attracted significant attention in recent years. REEs have emerged as essential metals in modern-day technology due to their unique functions. Long-term large-scale mining and utilization of rare earths have caused serious environmental pollution and constitutes a global health issue, which raised concerns about human health safety. However, the toxicity profile of suspended particulate matter of REEs in the environment interacts with the human body in remain largely unknown. Studies have shown that REEs can enter the human body through a variety of pathways, leading to a variety of organ and system dysfunctions through changes in genetics, epigenetics, and signaling pathways. Through an extensive literature search and critical analysis, we provide a comprehensive overview of the available evidence, identify knowledge gaps, and make recommendations for future research directions.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

Time and space are fundamental concepts for characterizing and understanding our world. Despite of continuous curiosity and extensive studies, the nature of time and space remains elusive, and the underlying quantum structure is unclear. Here we propose a molecular model based on energy space decomposition to incorporate time and space synthetically in a unified framework. In the proposed model, the multipole expansion of action mapped to energy modules in scalar, vector, and matrix forms, results in the generators of time, space, and a material framework, cloud. And the invariance of time, space and cloud transformation corresponds to the conservation of energy, momentum, and mass, respectively. The classification of energy modules reveals a periodicity of energy elements, which constructs a hierarchical world in a molecular framework with dynamics represented by energy transformations. Here the role of time and space could switch from each other, and motion is attributed to the coupling of particle with intermediate bosons, corresponding to energy transformations among different energy modules. The application on Bohr model demonstrates that this picture provides a consistent classical interpretation to the foundation of quantum mechanics, and suggests an atomic model for gravitation.

Saline-alkaline aquaculture has become important breakthrough to expand available space for aquaculture in China. However, the biochemical composition and quality of Eriocheir sinensis reared in carbonate alkalinity water are still unclear. Therefore, this study investigated the edible yield, coloration, nutritional and flavor quality of Eriocheir sinensis. Significantly lower gona-dosomatic index (GSI) and meat yield (MY) were detected in intensive pond (IP) than those in semi intensive reed wetland (SIWR) (P< 0.05). Six color parameters differed between IP and SIRW in the hepatopancreas (P< 0.05). The contents of crude protein and fat in the female hepatopan-creas of IP were significantly higher than those in SIRW(P< 0.05). The higher concentrations of ∑MUFA, ∑EFA, h/H in the female edible tissues were checked in IP than those in SIRW, with significant difference including ∑MUFA in the hepatopancreas and ovary, ∑EFA in the muscle, and h/H in the ovary (P<0.05). Better total free amino acid (∑FAA) contents of muscle were de-tected in SIRW than that in IP. Significantly increasing tendency was detected in K, Ca, Mg, Fe, Zn of ovary from SIRW to IP (P< 0.05). Overall, the Eriocheir sinensis reared in carbonate alkalinity water is an important source of nutrient.

Lightweight component design is effectively achievable through the sandwich structures, many past research studies in the aerospace and racing sectors (since 1920s) has proven it. To extend their application into automotive and other transport industries, the manufacturing cycle times must be reduced. This can be achieved by thermoplastic sandwich materials of continuous fibre-reinforced thermoplastic (CFRTP) cover layers and thermoplastic honeycomb cores. To widespread the application of flat thermoplastic-based sandwich panels into complex parts, a novel forming technology was developed by the Fraunhofer Institute of Microstructure of Materials and Systems (IMWS). For an increase in reproducibility of the sandwich component production and a decrease in manufacturing defects, numerical modelling methods and experimental validation are needed. The finite element (FE) modelling of this thermoforming process is a thermo-mechanical assignment with all three: material, geometry, and boundary non-linearities. In the scope of this work, the material behavior of different sandwich components (cover layers, honeycomb core, interface) under thermo-mechanical loads is characterized in detail, and a complex numerical model is developed to describe the thermoforming process of thermoplastic-based sandwich laminate. The critical forming condition like wrinkling that occurs due to friction in a sandwich or poor intra-ply shear in cross-ply studied, validated, and optimized. A thermoplastic sandwich made of polypropylene (PP) honeycomb core and polypropylene glass fibre (PP/GF) cross-ply as cover layers was used for this study, and numerical modelling was executed in LS-DYNA software.

There are two basic methods for radial external load distribution calculation on rolling elements in a rolling element bearing: the discrete method and the integral method. Solving the discrete equilibrium quasi-static equation using the Newton-Raphson scheme, more accurate results are derived than those based on the integral method, with small theoretical and computational efforts. The Sjövall’s radial integral factors, as well as some approximations proposed in the literature, for line- and point-contacts, are revisited. Numerical approximations for the Sjövall's radial integrals are proposed. The approximations’ errors with respect to the Sjövall’s radial integral’s numerical integration are shown. The numerical results of the displacement between inner and outer rigid rings, maximum hertzian contact deflection and the most loaded element load are shown for some ball and roller bearings, for radial external load ranging from 0 to 10,000 N, and for positive, negative and zero radial clearance, solving the discrete equilibrium quasi-static equation using the Newton-Raphson method. A total of 16 figures is shown in this work, many of which are made up of sub-figures. A total of 58 figures and sub-figures is shown.

The insufficient toughness of concrete can lead to the occurrence of crack expansion, ultimately resulting in a decline in the physical and mechanical properties such as bearing capacity and deformation characteristics of structural components. In severe cases, this may lead to brittle failure, where the entire structure and system fail suddenly without significant deformation after being stressed. Additionally, during the process of shear and bending failure of reinforced concrete beams, the cracks generated on the side of the beam are mostly I-II composite cracks. Considering the material nonlinearity and geometric irregularity of reinforced concrete, it is of great significance to study the dynamic evolution law of crack expansion in reinforced concrete members. Based on experimental data, this paper aims to utilize the nonlinear finite element simulation software Abaqus to conduct finite element simulations of crack expansion in simple supported reinforced concrete beams. By accurately controlling the constitutive curves of concrete and reinforcement materials, the design of seismic performance of structural members can be enhanced, thereby making essential contributions to the preliminary analysis of actual crack control engineering. The nonlinear finite element results indicate that the joint cracks of the frame with the floor slab primarily manifest as flexural cracks, with the concrete damage degree of the floor slab being higher than that of the beam. This finding underscores the importance of considering the behavior of concrete and reinforcement materials in designing for seismic performance and crack control in actual engineering applications.

In this study, the autofrettage method, which is used to increase the durability of cylindrical parts, was applied to a barrel made of steel material according to the AISI 4340 standard. Assuming that the barrel works continuously under the pressure of 400 MPa, optimum autofrettage was performed. The stresses occurring on the barrel before and after autofretage were calculated. Additionally, analytical equivalent stress values (Von-Mises) formed on the part's wall were compared with numerical analysis results obtained with a commercial finite element program ANSYS®, and their compatibility was examined. As a result of the calculations and analysis performed, it was observed that autofretage has positive effect on increasing the pressure carrying capacity of the barrel. After autofrettage the cylindrical part, it was determined that the Von-Mises stress values formed in the part wall changed and these stresses took the lowest value at a point (elastic-plastic interface). It has been evaluated that this point gives the optimal autofretage pressure value for a certain operating pressure. After the autofrettage application, it was determined that the Von-Mises Stress value in the barrel wall decreased by 25.27 % and the pressure carrying capacity of the barrel increased without any design or dimensional change. It has been seen that the analytical and numerical analysis results are consistent with each other, and it is expected that this study will guide and contribute to the studies to be conducted on increasing the strength or lightening the weight of the parts.

In recent years, with the increase in maritime trade, the necessity of increasing the capacities of the ports has emerged. However, while it is planned to increase the capacities of the ports, it is important that the port continues to operate at the same time. In this respect, the old port structures should not be damaged during the capacity increase. In this study, the strengthening of a port in Guinea is discussed as a case study. In the study, the existing quay wall was evaluated, and geotechnical and structural alternatives of the new structure to be built for capacity increase were evaluated. A combined system was designed as a pile foundation and a reinforced foundation with plastic piles so as not to damage the existing quay wall. The pile capacities obtained as a result of the analyses were verified by loading tests.

The vibration response of soil is a key property in the field of agricultural soil tillage. Vibration components of tillage machinery are generally used to reduce tillage resistance and improve work efficiency, the pressure variation under low-frequency vibration will affect the fragmentation and dispersion of farmland soil. However, the gradient of pressure variation, frequency domain response, and effective transmission range are unclear. A new method based on DEM (Discrete Element Method) is presented to study the vibration response and pressure transmission under low-frequency vibration. Bench test results showed that peak pressure positively correlates with the vibration frequency and attenuates rapidly at the vibration distance of 100 to 250 mm. The results data were also selected to determine the simulation model parameters. Amplitude, vibration frequency, and soil depth were used as test factors in single-factor simulation tests, and their effects on the peak pressure, frequency domain response, and effective transmission distance were analyzed. The results showed a positive relationship between the peak pressure and the test factors. The peak pressure increases with a maximum gradient of 19.02 kPa/mm at a vibration distance of 50 mm. The amplitude, vibration frequency, and soil depth positively correlate with the dominant frequency amplitude. The main frequency is independent of amplitude and soil depth. At the vibration distance of 250 mm, the dominant frequency is approximately twice the vibration frequency at 7–11 Hz and approximately equal to the vibration frequency at 13–15 Hz. Multiple exponential functions were used to fit the peak pressure attenuation function, obtaining an effective transmission distance range of 347.15 to 550.37 mm for the 5kPa cut-off pressure. For a soil depth of 300 mm, the vertical shear wave diffusion angle is greater than the horizontal shear wave diffusion angle. The study clarifies the vibration response of soil under low-frequency vibration, which helps to design vibration type soil-engaging components of tillage machinery and match vibration parameters for energy saving and resistance reduction in soil tillage.

For deep-penetrating geochemistry, there is a frontier issue as to how to explore ore-bearing information deep in covered areas, while it is, too, important to investigate the geochemical migration of ore-forming elements for the development of exploration geochemistry. In this study, a 380-day migration column experiment was conducted with surface soil and pure Cu powder collected from the Yujiashan study area in Wuhan City, Hubei Province taken as the object of research to simulate the migration process of ore-forming elements under natural conditions. The results showed obvious vertical migration of the ore-forming elements and conversion of mobile metal forms in the process; further, according to 6 groups of simulation experiments that took 45 days to conduct on migration column samples and the surface oil and Cu powder collected from the Pulang mining area in Yunnan Province, the vertical migration of the ore-forming element was still visible, and the exogenous substance (pure Cu powder) could enhance the anomaly without changing the basic migration mechanism. This indicates that Cu might migrate in a stable manner in soil cover in the Pulang mining area, and its migration was mostly driven by the transformation of Fe-Mn oxide bound state and organic bound state; finally, a multifractal analysis was conducted, revealing that the ore-forming elements presented a nonlinear and complex structure during their upward migration, which caused anomalies in the covered area, and multiple parameters exerted a certain indicative effect on different source intensities and properties of soil. In this study, laboratory simulations were performed to summarize the active-state evolution pattern and migration mechanism of ore-forming elements with a view to providing technical support and theoretical guidance for geochemical prospecting in the covered region.

This paper presents a finite element analysis of the bi-directional orthogonal model, which incorporates individual crack strain separation and tracking. The objective of the research is to expand the current shear friction model to manage bi-directional cracking at any angle, allowing for a more universal model that can be applied to intricate structures and non-proportional loading cases. The proposed model was initially developed as a total strain-based model, with the assumption that crack strains are equivalent to total strains, but was subsequently recalculated to improve accuracy by separating crack strains from total strains. Furthermore, a separate crack strain formulation was created to account for strains in the concrete's uncracked portions and locked-in crack strains. The article then discusses the testing of various convergence methods and loading programs to achieve high convergence. Comparative analyses of the generalized shear friction model with other models for crack orientation and loading cases similar to those of a reinforced concrete membrane are also presented. The MATLAB program successfully applied the bi-directional cracking model for one finite element under a uniform cyclical strain state, using a secant stiffness formulation.

Crystallization often occurs in the laser welding of amorphous alloys, reducing the amorphous alloys’ properties. So, it is necessary to simulate the temperature field curve of the welding area by computer and then determine the power and laser moving speed of laser welding. In this paper, the temperature field curve of Zr41.2Ti13.8Cu12.5Ni10Be22.5(Vit1) amorphous alloy in laser welding is obtained by finite element analysis. The continuous heating curve (CHT) of Vit1 is fitted by the Vogel-Fulcher-Tammann (VFT) equation and the Kissinger equation. If the temperature field curve intersects with the CHT curve, crystallization occurs. The experiment results show that the VFT equation can be used to predict the crystallization of Vit1 better in laser welding. The tem-perature and welding time are increased by using low welding speed. Therefore, the temperature of the weld zone cannot fall in time, resulting intersection of the temperature field curve and the CHT curve. So, crystallization can be avoided if the welding speed is controlled within a rea-sonable range, and the highest temperature is kept under the CHT curve.

Wearable thermoelectric generators (w-TEGs) convert thermal energy into electrical energy to realize self-powering of intelligent electronic devices, thus reducing the burden of battery replacement and charging, and improving the usage time and efficiency of electronic devices. Through finite element simulation, this study successfully designed high-performance thermoelectric generator and made it into wearable thermoelectric module by adopting “rigid device - flexible connection” method. It was found that higher convective heat transfer coefficient on cold-end leads to larger effective temperature difference and better power generation performance of device in typical wearable scenario. Meanwhile, at same convective heat transfer coefficient on the cold-end, longer TE leg length leads to larger temperature difference established at both ends of device, larger device output power and open-circuit voltage. However, when the convective heat transfer coefficient increases to a certain level, optimization effect of increasing TE leg length on device power generation performance will gradually diminish. For devices with fixed temperature difference between two ends, longer TE leg length leads to higher resistance of TEG, resulting in lower device output power but slight increase in open-circuit voltage. Finally, sixteen 16×4×2 mm2 TEGs (L=1.38 mm, W=0.6 mm) and two modules were fabricated and tested. At hot end temperature Th=33 ℃ and cold end temperature Tc=30 ℃, the actual maximum output power Pout of TEG is about 0.2 mW, and the actual maximum output power Pout of TEG module is about 1.602 mW, which is highly consistent with the simulated value. This work brings great convenience to research and development of wearable thermoelectric modules and provides new, environmentally friendly and efficient power solution for wearable devices.

The link of fracture analysis of large ships is an essential part of the structural safety of ships. However, the finite element analysis of large structure according to the traditional method not only has high requirements on the computer, but also the influence of the mesh encryption at special locations makes further requirements on the accuracy of the ship. In this paper, based on the extended finite element method (XFEM) and the multi-point constraint method (MPC), the dynamic crack expansion process of the rectangular plate containing cracks under the multi-scale model is comparatively studied by using ABAQUS simulation software Finally, the applicability of the method is verified by applying the multi-scale model of ship nodes. The results show that the computational effort of the multi-scale model is significantly reduced with the same accuracy and allowable error, which proves the accuracy and efficiency of the method.

Condition monitoring is today a crucial and unavoidable practice related to the use of widespread mechanical components as rolling element bearings. Despite the diffusion of new data-driven techniques to analyze vibrational signals and detect the state of health of the system, mathematical tools, deriving more or less directly from the Fourier transform and defined either on the time or the frequency domain or on a combination of them (i.e. signal-based techniques), remain still essential and irreplaceable in the light of the deep and detailed information they provide. In this paper the diagnostic efficacy of an ample spectrum of these methods is investigated, applying them to study faults occurrence in the first bearing dataset released by NASA IMS Center. Thanks to their analytical definition, which is formulated taking into consideration to some extent the mathematical nature of the signal, faults signatures can be clearly identified and their temporal development can be fully traced, confirming their ability as powerful means to constantly monitor the state of a system even in real-time applications.

This paper presents the experimental and numerical studies of the vertical stress distribution beneath the centerline of circular footings resting on the sand. Vertical stress values due to circular load in medium-dense sand were measured using soil stress transducers. Reduced-scale laboratory model tests were carried out in a square-shaped test box and vertical stresses were measured at the centerline of the circular footing at different depths of the sand. In order to determine the effect of footing width on vertical stress distribution, laboratory experiments were performed on circular footings of different diameters. In addition, a series of finite element analyses was carried out on the test model to validate the findings of the experimental study. In the numerical analysis, the sand was modeled as a non-linear elastoplastic material. The analyses were performed using the finite element method with two-dimensional axisymmetric and three-dimensional conditions. The results obtained from laboratory model tests and numerical analysis were compared with the vertical stress values obtained from the theoretical solution in the literature. Vertical stress distribution in horizontal planes at any depth from the footing base shows the same characteristic form in all methods. However, some differences were observed between experimental, numerical, and theoretical results and discussed.

In engineering, connections between components are often weak areas. Unreasonable connection methods can easily reduce the strength of components, resulting in unpredictable failure modes. In nature, numerous connection methods for biological structures with excellent mechanical properties have evolved. Studying the connection methods of organisms in nature can inspire new ideas for bionic connection methods. When the diabolical ironclad beetle is under pressure, the elytra are not easy to separate, which ensures the stability of the beetle's external structure, thus making the beetle extremely resistant to pressure. The reason for this is the interlocking and toughening effect of the unique jigsaw connection between the elytra. Therefore, in this paper a theoretical analysis model is established and used to analyze the mechanical behavior of the diabolical ironclad beetle's jigsaw connection during the drawing process and determine the influence of factors such as quantity, angle, and geometric characteristics on the mechanical properties of the jigsaw connection. The results of the theoretical analysis are then compared with the results of experiments and ABAQUS finite element simulation.

This article presents a case study on the structural assessment of a reinforced concrete (RC) foundation exposed to low temperatures. The foundation supports a 19,500 m³-capacity tank with low-temperature (-89°C) ethane. Icing and bubbling were observed on the tank’s surface soon after it started operations. Condensation was also observed at the bottom of the 0.8 m-depth RC slab, which raised concerns about the structural condition of the concrete. This study provides details of the field and analytical investigations conducted to assess the structural condition of the foundation. Heat transfer finite element (FE) analyses were performed to examine the concrete sections subjected to low temperatures. It was found that the ethane leakage produced a low temperature on the top side of the concrete foundation of +9.7°C. Overall, the temperatures calculated by the FE analyses were in good agreement with actual field measurements, within a ±5% accuracy. The simplified heat transfer equation for porous media used in this study was sufficiently accurate to model the effects of the ethane leakage in the concrete foundation, provided the ambient temperature at the site is taken into account in the analysis. The results also confirm that reinforcing bars can be neglected in the thermal analysis of massive concrete slabs. The results from the field measurements and FE analyses confirmed that the structural integrity of the RC foundation was never compromised. The approaches, methods and techniques discussed in this article are deemed suitable to solve the practical and scientific challenges involved in the structural assessment and repairs of large special structures. Accordingly, they can serve as useful reference and guidance for engineers and practitioners working in the field of forensic engineering.

The Gol'denveizer problem of a torus was studied analytically by Audoly and Pomeau (2002), and the accuracy of the Audoly and Pomeau linear law was confirmed numerically by Sun (2021). However, the law does not include the major radius R of the torus. To find the influence of the major radius, we used finite element numerical simulation to simulate different cases, and we propose a modified Audoly and Pomeau linear law for vertical deformation, which includes R. A linear law of horizontal deformation is presented as well. Our studies show that the Audoly and Pomeau linear law has high accuracy. With modified vertical and horizontal deformation, a displacement-compatible relation between them is formulated.

Orofacial injuries are common occurrences during contact sports activities; however, there is an absence of data regarding the performance of hybrid occlusal splint mouthguards, especially during compressive loading. To evaluate the total deformation and stress concentration, a skull model was selected and duplicated to receive two different designs of mouthguard devices: one model received a conventional custom-made mouthguard (MG) with 4-mm thickness and the other received a novel hybrid occlusal splint-mouthguard (HMG) with the same thickness. Both models were subdivided into finite elements. The frictionless contacts were used, and a nonlinear analysis was performed simulating the compressive loading in occlusion. The results were presented in von-Mises stress maps (MPa) and Total Deformation (mm). A higher stress concentration in teeth was observed for the model with the conventional MG, while the HMG design displayed a promising mechanical response with lower stress magnitude. The HMG de-sign displayed a higher magnitude of stress on its occlusal portion than the MG design. The hybrid mouthguard (HMG) reduced (1) jaw displacement during chewing and (2) the generated stresses in maxil-lary and mandibular teeth.

In this note we generalize the regularity concept for semigroups in two ways simultaneously: to higher regularity and to higher arity. We show that the one-relational and multi-relational formulations of higher regularity do not coincide, and each element has several inverses. The higher idempotents are introduced, and their commutation leads to unique inverses in the multi-relational formulation, and then further to the higher inverse semigroups. For polyadic semigroups we introduce several types of higher regularity which satisfy the arity invariance principle as introduced: the expressions should not depend of the numerical arity values, which allows us to provide natural and correct binary limits. In the first definition no idempotents can be defined, analogously to the binary semigroups, and therefore the uniqueness of inverses can be governed by shifts. In the second definition called sandwich higher regularity, we are able to introduce the higher polyadic idempotents, but their commutation does not provide uniqueness of inverses, because of the middle terms in the higher polyadic regularity conditions.

Energy efficiency and leakage magnetic field (LMF) are two important issues in electric vehicle inductive chargers. In this work, the maximum achievable coil efficiency and the corresponding LMF strength are formulated as functions of hardware parameters, and figure of merits (FOM) are proposed for assessing the efficiency and LMF performance of the coil assembly pair. The impacts of the coil assemblies’ geometric parameters on both FOMs are examined with the aid of finite element analysis (FEA), and measures to improve the FOMs are extracted from FEA results. A coil assembly pair is manually optimized within given dimensional limits. Compared with the initial design, the optimized one achieves higher efficiency and lower LMF strength while consuming less copper. The performance improvement is verified by FEA results and experimental data measured on an 85 kHz electric vehicle inductive charger prototype. The key measures for coil assembly optimization are summarized.

The effect of the different dental implants positioning region on the stress performance of the implant-supported prosthesis is not yet clear. This study evaluated the dental treatment with six dental implants in three different models and three different occlusal loading conditions, in terms of the biomechanical response of implants, prosthetic screw and maxilla, using three-dimensional finite element analysis. The finite element models were modelled containing external hexagon implants, as well as a Cobalt-Chromium superstructure. Three types of loads were applied: in the area of ​​the central incisors, first premolar and in the second molars. For the finite element simulations, the von-Mises stress peaks in the implant and in the surrounding cortical bone were analyzed. All recorded results reported higher values ​​for the implant-supported prosthesis in group C compared to the groups A and B. The highest stress values, ​​regardless the evaluated model, was in the prosthesis in group C and in screws, the smallest were in group A.

In the process of metal cutting, the anti-wear performance of the tool determines the life of the tool and affects the surface quality of the workpiece. The finite element simulation method can directly show the tool wear state and morphology, but due to the limitations of the simulation time and complex boundary conditions, it has not been commonly used in tool life prediction. Based on this, a tool wear model was established on the platform of a finite element simulation software for the cutting process of titanium alloy TC4 by end milling. The key technique is to embed different types of tool wear models into the finite element model in combination with the consequent development technology. The effectiveness of the tool wear model is validated by comparing the experimental results with the simulation results. At the same time, in order to quickly predict the tool life, an empirical prediction formula of tool wear was established, and the change course of tool wear under time change was obtained.

Since large power transformers are custom-made, and their design process is a labor-intensive task, their design process is split into different parts. In tendering, the price calculation is based on the preliminary design of the transformer. Due to the complexity of this task, it belongs to the most general branch of discrete, non-linear mathematical optimization problems. Most of the published algorithms are using a copper filling factor based winding model to calculate the main dimensions of the transformer during this first, preliminary design step. Therefore, these cost optimization methods are not considering the detailed winding layout and the conductor dimensions. However, the knowledge of the exact conductor dimensions is essential to calculate the thermal behaviour of the windings and make a more accurate stray loss calculation. The paper presents a novel, evolutionary algorithm-based transformer optimization method which can determine the optimal conductor shape for the windings during this examined preliminary design stage. The accuracy of the presented FEM method was tested on an existing transformer design. Then the results of the proposed optimization method have been compared with a validated transformer design optimization algorithm.

This study presents the development of a number of finite element (FE) models of the pelvis using different continuum and structural modelling approaches. Four FE models were developed using different modelling approaches: continuum isotropic, continuum orthotropic, hybrid isotropic and hybrid orthotropic. The models were subjected to an iterative adaptation process based on the Mechanostat principle. Each model was adapted to a number of common daily living activities (walking, stair ascent, stair descent, sit-to-stand and stand-to-sit) by applying onto it joint and muscle loads derived using a musculoskeletal modelling framework. The resulting models, along with a structural model previously developed by the authors, were compared visually in terms of bone architecture, and their response to a single load case was compared to a continuum FE model derived from CT imaging data. The main findings of this study were that the continuum orthotropic model was the closest to the CT derived model in terms of load response albeit having less total bone volume, suggesting that the role of material directionality in influencing the maximum orthotropic Young's modulus should be included in continuum bone adaptation models. In addition, the hybrid models, where trabecular and cortical bone were distinguished, had similar outcomes, suggesting that the approach to modelling trabecular bone is less influential when the cortex is modelled separately.

Both drag and lift forces impact an inclined plane when it is dragged through a granular bed. In this paper, the following results have been obtained: the drag and lift forces grow with the velocity of motion; when the immersion depth is constant, the inclination angle has no effect on drag force, however, the lift force increases linearly with this inclination angle; the ratio of drag and lift forces is exactly equal to the tangent value of the inclined angle. In order to describe this physical process macroscopically, a continuum wedge model based on the Coulomb model is established to predict drag and lift forces. Particularly，the dynamic friction angle in the assumed shear band is predicted as a function of both inclined angle and moving velocity.

Interface between matrix/coating or coating/coating in fact represents a very complicate thin interfacial layer. So interface model is necessary to avoid the difficulty on considering such a complicate thin layer in analysis. Classic interface model and cohesive model have been widely used in stress analysis of coating materials, though they cannot represent the effect of very thin interfacial layer accurately. A complete interface model has been deduced from the equivalent constitutive of interfacial layer in this paper. It is found that both classic interface model and cohesive model sometimes cannot give correct analysis results, while the complete interface model can always give a correct result. Moreover, the stress parallel to interface within the interfacial layer can also be analyzed by the new model. Besides, this model can also be used to describe the equivalent properties of interfacial layer, thereby, can provide a quantitative characterizing method for interfacial layer itself.

Concrete-filled steel columns have been extensively used in the world due to having all suitable characteristics of concrete and steel, more ductility, increasing concrete confinement using steel wall, large energy-absorption capacity and appropriate fire behavior. In present paper, concrete-filled steel square columns have been simulated under the influence of blast load using ABAQUS software. These responses will be compared for scaled distances based on the distance to source and weight of explosive material. As result, it can be seen that although concrete deformation has been restricted using steel tube, but inner layer of concrete has been seriously damaged and column displacement will be decreased by increasing scaled distance. We also concluded that concrete-filled steel columns have high ductility and blast resistance.

Osteoporosis is considered a serious public health problem, particularly affecting the postmenopausal period. In 2018, in the Republic of Kazakhstan the total and primary incidence was 10 and 3.7 cases per 100,000 adults, respectively. The objective is to study osteoporosis prevalence and indicate main factors affecting low bone mineral density by screening adult population of Abay region, Kazakhstan. The target group were 641 respondents aged between 18 and 65 years old, Kazakh population living in Abay region since birth. All participants filled out questionnaire and had a bone mineral density measurement by dual energy X-ray absorptiometry (DXA) between July 15, 2023 and February 29, 2024. Logistic regression analysis was conducted to assess the association between low bone mineral density and key demographic characteristics, aforementioned lifestyle factors and nutrition habits. We identified the prevalence of low bone density and osteoporosis at the level of 34.1% with the highest prevalence in the older population group (50+ years) - 48.3%. Regression analysis revealed a number of indicators associated with the likelihood of bone sparing. However, only 4 of these showed significance in the final multivariate model (R2=22.4%). These included age (AOR 1.05), body mass index (AOR 0.92), fracture history (AOR 1.64), consumption of nuts and dried fruits were associated with lower prevalence of osteoporosis (AOR 0.48). Our study was the first in Kazakhstan that investigates the association of key demographic, behavior and anamnestic factors with low mineral density.

Ralstonia solanacearum is the pathogen responsible for Ralstonia solanacearum, which is soil-borne, infests plant conduits to cause disease.They are not easy to control and are harmful.Therefore the development of a controlled-release agent responsive to the pathogen's soil temperature and moisture conditions could aid in its control. Corn kernel powder is used as a carrier for Tetramycin biopesticide, with various compounds tested for bonding.They were then made by extrusion moulding.Temperature and wetness responsive components, including Pentaerythritol Tetrastearate, Pentaerythritol Tetraoleate, Polyethylene Glycol Stearate, and Polyethylene Glycol Monooleate,are compounded and coated onto Tetramycin cores to form an intermediate shell layer. Finally, Ethyl cellulose(EC)and Hydroxypropyl methyl cellulose(HPMC) are dissolved and sprayed onto the outermost layer to complete the pellet's shell layer.After the evaluation of texture performance test,DSC analysis,TG test,temperature and humidity response performance test, as well as pellet cross-section SEM observation, field effectiveness test, etc., the preferred formulations were screened.The results showed that the preferred Core formulation:Corn kernel powder:Tetramycin aqueous:Xanthan gum mass ratio=13.5:23:2; Intermediate Shell layer:PETS: PETO: PEG400MO mass ratio=10:30:10; and Outer Shell layer: Ethyl cellulose (EC):Hydroxypropyl methyl cellulose (HPMC) mass ratio=5:1.Under soil conditions of high incidence of Ralstonia solanacearum, i.e., sustained warmth (30-35℃) and high humidity (30% moisture content), the formulated pills showed a release rate of 95.18% to 96.24% over a period of 35 days. Moreover, they showed a stepwise cyclic release process under alternating warm and humid-dry and cold conditions.In field tests on tobacco, a relative preventive efficacy of 54.74% was achieved 106 days post-transplanting. Soil bacterial community structure analysis revealed a significant decrease (2.28-2.84 times) in the abundance of Solanaceae Raelia under Tetramycin pellet treatment compared to the control. Additionally, fungal community structure showed highter consistency initially across various soil depths, with diversity differences between soil layers reestablished later (106 days), while the predominant categories of bacteria and fungi remained unchanged.In this study, we successfully developed a nucleoshell-type slow-controlled release pill embedded with Tetramycin. This pill effectively responded to temperature and humidity changes, resulting in high efficacy in disease prevention.This development holds significant promise for effectively improving drug utilization and easing application challenges, offering broad prospects for Ralstonia solanacearum prevention and control in agriculture.

Chest X-ray (CXR) is the first tool globally employed to detect cardiopulmonary pathologies. These acquisitions are highly affected by scattered photons due to the large field-of-view required. Scatter in CXRs introduces background in the images, which reduces their contrast. We developed three deep learning-based models to estimate and correct the scatter contribution to CXRs. We used a Monte Carlo (MC) ray-tracing model to simulate CXRs from human models obtained from CT scans using different configurations (depending on the availability of dual-energy acquisitions). The simulated CXRs contained the separated contribution of direct and scattered X-rays in the detector. These simulated datasets were then used as the reference for the supervised training of several NN. Three NN models (single and dual energy) were trained with the MultiResUNet architecture. The performance of the NN models was evaluated on CXRs obtained with the MC code from chest CTs of patients affected by COVID-19. The results showed that the NN models were able to estimate and correct the scatter contribution to CXRs with an error &lt;5%, being robust to variations in the simulation setup and improving the contrast in soft tissue. The single-energy model was tested with real CXRs, providing robust estimations of the scatter-corrected CXRs.

Legume-rhizobial symbiosis leads to to the formation of root nodules, where rhizobia reside and develop into bacteroids to reduce nitrogen into ammonium for plant growth, which leaves an opening question as how plant immunity is attenuated in nodules in the presence of large number of foreign bacteria. In Medicago truncatula, mutation in NAD1 (Nodules with Activated Defense 1) only produces necrotic nodules with overactivated immunity, indicating NAD1 is an indispensable component required for suppressing immunity in nodules. In this study, a dual RNA-seq transcriptomic technology was performed to extensively analyze gene expressions in nad1-1 mutant nodules. We indenifited 89 DEGs in symbiotic nitrogen fixation and 89 DEGs in immunity in Medicago truncatula at 10 dpi. Simultaneously, we indenifited 27 DEGs in fix and nif genes in Sinorhizobium meliloti. Then we identified 56 DEGs related to stress, including ROS, NO, and NCR, most of which were upregulated in Sinorhizobium meliloti. Our analyses of nitrogen fixation-defective plant nad1-1 mutants with overactivated defense indicate that host use plant immunity to control massive bacterial colonization during early and late symbiotic stages. Our findings provide insight into the function of NAD1 in improvement or inhibition of plant immune response to maintain symbiosis during rhizobial endosymbiosis.

To compare the quality of low-energy VMIs obtained with three DECT platforms according to phantom diameter. Three sections of the Mercury Phantom 4.0 were scanned on two generations of split-filter CTs (SFCT-1st and SFCT-2nd) and on one Dual-source CT (DSCT). Noise power spectrum (NPS), task-based transfer function (TTF) and detectability index (d’) were assessed on VMIs from 40 to 70keV. Highest noise magnitude values were found with SFCT-1st and noise magnitude was higher with DSCT than with SFCT-2nd for 26-cm (10.2±1.3%) and 31-cm (7.0±2.5%), and the opposite for 36-cm (-4.2±2.5%). The highest average NPS spatial frequencies and TTF values at 50% (f50) values were found with DSCT. For all energy levels, f50 values were higher with SFCT-2nd than SFCT-1st for 26-cm (3.2±0.4%) and the opposite for 31-cm (-6.9±0.5%) and 36-cm (-5.6±0.7%). The lowest d’ values were found with SFCT-1st. For all energy levels, d’ values were lower with SFCT-2nd than with DSCT for 26-cm (-6.2±0.7%), similar for 31-cm (-0.3±1.9%) and higher for 36-cm (5.4±2.7%). In conclusion, compared to SFCT-1st, SFCT-2nd exhibited lower noise magnitude and higher detectability values. Compared with DSCT, SFCT-2nd had lower noise magnitude and higher detectability for the 26-cm but the opposite was true for the 36-cm.

Relay protection service is the most crucial service carried by the electric power communication network, which is directly linked to the safe operation of the power grid. In the route planning of power services, a route planning architecture for the power communication network is constructed in this paper, considering the operation and maintenance requirements, such as relay protection service overload (RPSO) and dual route. To minimize network risk variance, the problem of single-service route allocation is formulated by taking the factors into account such as service delay, link bandwidth utilization, and RPSO constraints. Based on $k$ shortest paths algorithm, a route planning scheme for the power services is proposed, which considers RPSO and risk balance, and a strategy for implementing multi-service route planning of the communication network is studied. The simulation results show that the proposed route planning strategy can effectively avoid relay protection service overload, reduce network risk variance, and balance network risk.

Cross-field innovation in faba bean breeding has added significant value to the traditional faba bean planting industry by allowing for the selection of faba bean varieties with a dual purpose as ornaments and food. In order to improve the selection efficiency, we determined 17 phenotypes related to ‘dual purpose’ faba beans and evaluated 37 new breeding lines, which were bred for 10 years by our team, and two traditional faba bean varieties by means of an Analytic Hierarchy Process. The lines and varieties were evaluated and sorted into five grades, from which two breeding lines with excellent comprehensive phenotypes and dual ornamental and food functions were selected. The new line GS5 passed the identification of Crop Identification Committee of Chongqing Seed Industry Association on November 25, 2021 and was renamed "Doumei 1 hao" with the identification number of " 202111". The results confirmed that the comprehensive evaluation system constructed in this study can be used for the effective selection of dual-purpose faba bean lines, providing an empirical approach for strategic decision-making by breeders.

Type 2 diabetes mellitus (T2DM) accounts for one-sixth of deaths, globally, whereas cancer is the second leading cause of death in the U.S. T2DM is a known risk factor for many cancers. This review examines the link of Reactive oxygen Species (ROS)-altered metabolic and signaling pathways in T2DM to cancer. These reprogrammed metabolic and signaling pathways are activated that contribute to diabetic complications, impact redox balance (Oxidative Stress), and have differential roles in early and late stages of cancer. If the respiratory chain is highly reduced (as under hyperglycemic conditions) or if reduced cofactors accumulate, ROS are greatly elevated. ROS may cause mutations in mitochondrial DNA (mtDNA) that result in further ROS elevation. Amplification of ROS results in activation of PKC, an overarching signaling pathway that activates MAPK with subsequent regulation of several factors that result in pathophysiological manifestations of T2DM and cancer. Upregulation of PKC leads to deregulation of NF-kß that regulates the PKB/P13/Akt pathway that orchestrates cell survival, growth, proliferation, and glucose metabolism manifested in cancer. It also affects Insulin Receptor Substrate (IRS-1), decreasing insulin stimulated glucose transport and glucose uptake, disrupting subsequent cell signaling pathways contributing to the development of T2DM. Dyslipidemia is a hallmark of T2DM and cancer. ROS-induced lipid peroxidation leads to systemic inflammation, producing inflammatory prostaglandins, cytokines and chemokines that result in tumor proliferation, rapid tumor growth, and modulation of immunity. The dual role of ROS in early and late stages of cancer make antioxidant therapy precarious and may be responsible for controversial results. A system that delivers an antioxidant directly to mitochondria may be useful in inhibiting formation of ROS early during the pre-diabetic stage whereas antioxidant therapy must be halted in later stages to retard metastasis.

Starch is widely applied in various industrial sectors, including the food industry. Starch is used as a thickener, stabilizer, or emulsifier. However, arrowroot starch generally has weaknesses, such as unstable under heating and acidic conditions, which are generally applied to processing in the food industry. Modifications were applied to improve the characteristics of native arrowroot starch. In this study, arrowroot starch was modified by heat-moisture treatment (HMT), octenylsuccinylation (OSA), and dual modification between OSA and HMT in a different sequence, namely HMT followed by OSA, and OSA followed by HMT. This study aims to determine the effect of different modification methods on the physicochemical and functional properties of native arrowroot starch. The result shows that both single HMT and dual modification caused damage to native starch granules, such as the formation of cracks and roughness. Especially for single OSA treatment, there is no significant change in granule morphology after modification. All modification treatments did not change the crystalline type of starch but reduced the RC of native starch. Both single HMT and dual modifications (HMT-OSA, OSA-HMT) increased pasting temperature and setback, conversely decreasing the peak and breakdown viscosity of native starch. Whereas, single OSA has the opposite trend compared with the other modifications. HMT played a greater role in increasing the thermal stability and retrogradation ability of arrowroot starch. Both single modifications (HMT and OSA) increase the hardness and gumminess of native starch, conversely for dual modifications. HMT has a greater effect on color characteristics, where decreased the lightness and whiteness index of native arrowroot starch. Single OSA modification increased swelling volume higher than dual modification. Both single HMT and dual modifications increase water absorption capacity and decrease the oil absorption capacity of native arrowroot starch.

Environmental regulation has dual effects on water resource utilization performance through various channels such as the "three red lines" and the "Porter hypothesis". Based on the detailed analysis of the impact path of environmental regulation on water resource utilization performance, the two-step system GMM method was adopted to test the dual effects of environmental regulation on water resource utilization performance by using panel data of 30 provinces and cities from 2004 to 2020. The results show that: (1) Environmental regulation has a significant direct impact on water resource utilization performance, and is currently in the stage of positive relationship of an inverted u-shaped relationship. (2) Environmental regulation has a significant indirect impact on water resource utilization Environmental regulation has dual effects on water resource utilization performance through various channels such as the "three-red lines" and the "Porter hypothesis". In accordance with a detailed examination of the influence path of environmental regulation on the performance of water resource utilization, the double effects of environmental regulation on water resource utilization performance were examined using panel statistics from 30 provinces and cities from 2004 to 2020 using the two-step system GMM approach. The results demonstrate that: (1) Environmental regulation has a direct effect on water resource utilization performance which is currently in the stage of the positive relationship of an inverted u-shaped relationship. (2) The influence of environmental regulation on water resource utilization performance through government intervention and industrial structure adjustment is indirect, among which government intervention can significantly improve water resource utilization performance, while the growth of the tertiary industry as a percentage can lower water resource utilization performance. (3) Both direct and indirect impacts indicate that enhancing the efficiency of the use of water resources is sustainable, and the water resource utilization performance of the preceding period had a major positive impact over the present phase. Therefore, the paper sets out a few policy suggestions, such as choosing reasonable environmental regulation tools, actively guiding the market-oriented reform with constraints, and upgrading the industrial structure in a green way.

The tumour-associated isoenzymes, hCA IX and hCA XII catalyze the hydration of carbon dioxide to bicarbonate and protons. These isoforms are highly overexpressed in many types of cancer, where they contribute for the acidification of the tumor environment promoting the tumor cell invasion and metastasis. In this work, in order to identify novel dual hCA IX and XII inhibitors, virtual screening techniques and biological assays were combined. A structure based virtual screening towards hCA IX and XII was performed using a database of approximately 26000 natural compounds. The best shared hits were submitted to a thermodynamic analysis and 3 promising best hits were identified and evaluated in terms of their hCA IX and XII inhibitor activity. In vitro biological assays are in line with the theoretical studies and revealed that Syringin, Lithospermic acid, and (-)- Dehydrodiconiferyl alcohol behave as good hCA IX and hCA XII dual inhibitors.

The hybrid numbers are a generalization of complex, hyperbolic and dual numbers. In this paper, we introduce the Horadam hybrid polynomials called Horadam hybrinomials. We also give some special cases and algebraic properties of the Horadam hybrinomials. Finally we obtain some applications related to the Horadam hybrinomials in matrices.

Though the energy density of lithium-ion batteries continues to increase, safety issues related with the internal short-circuit and the resulting combustion of highly flammable electrolyte impede the further development of lithium-ion batteries. It has been well-accepted that a thermal stable separator is important to postpone the entire battery short-circuit and thermal-runaway. Traditional methods to improve the thermal stability of separators includes surface modification and/or developing alternate material systems for separators which may always affect the battery performance negatively. Herein, a thermostable and shrink-free separator with little compromise in battery performance is prepared by coaxial electrospinning and tested. The separator consists of core-shell fiber networks where poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) layer serves as shell and polyacrylonitrile (PAN) as the core. This core-shell fiber network exhibits little or even no shrinking/melting at elevated temperature over 250 °C. Meanwhile, it shows excellent electrolyte wettability and can take large amount of liquid electrolyte three times more than that of conventional Celgard 2400 separator. In addition, the half-cell using LiNi1/3Co1/3Mn1/3O2 as cathode and the aforementioned electrospun core-shell fiber network as separator demonstrates superior electrochemical behavior, stably cycling for 200 cycles at 1 C with a reversible capacity of 130 mAh g-1 and little capacity decay.

This study aimed to demonstrate the potential role of Dual Energy CT in assessing Bone Mineral Density (BMD) in postmenopausal women. A retrospective study was conducted on 51 postmenopausal female patients who underwent DXA and DECT examinations for other clinical reasons. DECT images were acquired with spectral imaging using a 256-slice system. These images were processed and visualized using an HAP(fat) map. Statistical analysis was performed using the Bland-Altman method to assess agreement between DXA and DECT HAP(fat) measurements. Mean BMD, vertebral and femoral T-scores were obtained. For vertebral analysis, the Bland-Altman plot showed an inverse correlation (R2: -0.042; RMSE: 0.690) between T-scores and DECT HAP(fat) values for measurements from L1 to L4, while a good linear correlation (R2: 0.341; RMSE: 0.589) it was found for measurements at the femoral neck. In conclusion, we demonstrated the enhanced accuracy of BMD calculation through DECT, finding a statistically significant correlation only at the femoral neck where BMD results do not seem to be influenced by the overlap of the measurements on cortical and trabecular bone. This outcome could be beneficial in the future by reducing radiation exposure for patients already undergoing follow-up for chronic conditions.

(1) Background: The prediction of cervical lesions evolution is a challenge for clinicians. The prospective study aimed to determine and compare the predictive accuracy of cytology, HPV genotyping, and p16/Ki67 dual staining alone or in combination with personal risk factors for the prediction of progression, regression or persistence of cervical lesions in human papillomavirus (HPV)-infected patients; (2) Methods: This prospective study included HPV-positive patients with or without cervical lesions that underwent follow-up. Descriptive statistics and sensitivity analysis for individual or combined index tests were used for data analysis; (3) Results: The highest predictive performance for the progression of cervical lesions was achieved by a model that comprised a Pap smear suggestive of high-grade squamous intraepithelial lesion (HSIL), the presence of 16/18 HPV strains, a positive p16/Ki67 dual staining result along with the presence of at least 3 clinical risk factors, which had a sensitivity (Se) of 74.42%, a specificity of 97.92%, an area under the receiver operating curve (AUC) of 0.961, and an accuracy of 90.65%. The prediction of cervical lesions regression or persistence was modest; (4) Conclusions: Multiple testing or new biomarkers should be used to improve HPV-positive patient surveillance, especially for cervical lesion regression or persistence prediction.

Background: Dual disorders (DD) involve the coexistence of substance use disorder (SUD) with another mental illness, often from psychotic and affective categories. This study explores the ef-fectiveness of brexpiprazole, a third-generation antipsychotic, in individuals diagnosed with schizophrenia spectrum disorder (DSM-V) and comorbid AUD/SUD (DSM-V). Methods: Eighteen enrolled patients underwent psychometric assessments at baseline and one month into brexpiprazole treatment administered at a mean dosage of 2 mg/day. Results: Brexpiprazole demonstrated significant reductions in psychopathological burden (PANSS total score, p=0.004), improved CGI total score (p=0.042), and decreased MOAS total score (p=0.012). Quality of life improved in SF-36 subscales (p<0.05). Substance craving reduction, though observed, did not reach statistical significance. Conclusions: This study provides initial evidence supporting brexpiprazole's efficacy and safety with positive effects on psychopathology and quality of life, emphasizing the need for tailored, comprehensive treatment strategies in this complex patient population.

In this paper we demonstrate first ever dual-period diffraction gratings that do not require electrical tuning to obtain the effect of period change. Our method allows for multiplication of the base period by proper modification of the subsequent slits of the grating. The proposed elements are fabricated by selective photopolymerization of a composite based on nematic liquid crystal. The gratings are formed by polymer stabilization of liquid crystal in different orientations of the molecules in selected grating slits to allow for period manipulation. The operating principle is based on changing the phase delay introduced by the slits depending on polarization direction of incident light with respect to the director in each type of slit, which allows to change the grating’s period. The proposed technique was successfully utilized to obtain diffraction gratings with either doubling or tripling of the period.

Dual antiplatelet therapy (DAPT), comprising aspirin and a P2Y12 receptor inhibitor, is the cornerstone of post-percutaneous coronary intervention treatment to prevent stent thrombosis and reduce the risk of adverse cardiovascular events. The selection of an optimal DAPT regimen, considering the interplay of various antiplatelet agents, patient profiles, and procedural characteristics, remains an evolving challenge. Traditionally, a standard duration of 12 months has been recommended for DAPT in most patients. While contemporary guidelines provide general frameworks, DAPT modulation with longer or shorter treatment courses followed by aspirin or P2Y12 inhibitor monotherapy are evolving towards an individualized strategy to optimize the balance between efficacy and safety. This review comprehensively examines the current landscape of DAPT strategies after coronary stenting, with a focus on emerging evidence for treatment individualization.

Dual localization or dual targeting refers to the phenomenon by which identical, or almost identical, proteins are localized to two (or more) separate compartments of the cell. From previous work in the field, we had estimated that a third of the mitochondrial proteome is dual targeted to extra-mitochondrial locations and suggested that this abundant dual targeting presents an evolutionary advantage. Here we set out to study how many additional proteins whose main activity is outside mitochondria are also localized, albeit at low levels, to mitochondria (eclipsed). To do this we employed two complementary approaches utilizing the α-complementation assay in yeast to uncover the extent of such eclipsed distribution: one systematic and unbiased and the other based on Mitochondrial Targeting Signal (MTS) predictions. Using these approaches, we suggest 280 new eclipsed distributed protein candidates. Interestingly, these proteins are enriched for distinctive properties compared to their exclusively mitochondrial-targeted counterparts. We focus on one unexpected eclipsed protein-family of the Triose-phosphate DeHydrogenases (TDH), and prove that indeed their eclipsed distribution in mitochondria is important for mitochondrial activity. Our work provides a paradigm of deliberate eclipsed mitochondrial localization, targeting and function, and should expand our understanding of mitochondrial function in health and disease.

Background and Aims. Most research on Parkinson's disease (PD) focuses on describing symp-toms and movement characteristics. Studies rarely focus on the early detection of PD and the search for suitable markers of a prodromal stage. Early detection is important, so treatments that may potentially change the course of the disease can be attempted early on. While gait disturb-ances are less pronounced in the early stages of the disease, the prevalence, and severity increase with disease progression. Therefore, postural instability and gait difficulties could be identified as sensitive biomarkers. The aim was to evaluate the discriminatory power of the Trail-Walking Test (Schott, 2015) as a potential diagnostic instrument to improve the predictive power of the clinical evaluation concerning the severity of the disease and record the different aspects of walking. Methods. 20 older healthy (M = 72.4 years, SD = 5.53) adults and 46 older adults with PD and the motor phenotypes postural instability/gait difficulty (PIGD; M = 69.7 years, SD = 8.68) and tremor dominant (TD; M = 68.2 years, SD = 8.94) participated in the study. The participants performed a motor-cognitive dual task (DT) of increasing cognitive difficulty in which they had to walk a given path (condition 1), walk to numbers in ascending order (condition 2), and walk to numbers and letters alternately and in ascending order (condition 3). Results. With an increase in the cognitive load, the time to complete the tasks (seconds) become longer in all groups, F(1.23, 73.5) = 121, p < .001, ɳ2p = .670. PD-PIGD shows the longest times in all conditions of the TWT, F(2, 60) = 8.15, p < .001, ɳ2p = .214. Mutual interferences in the cognitive and motor domain can be observed. How-ever, clear group-specific patterns cannot be identified. A differentiation between the motor phenotypes of PD is especially feasible with the purely motor condition (TWT-M; AUC = . 685, p = 0.44). Conclusions. PD patients with PIGD must be identified by valid, well-evaluated clinical tests that allow a precise assessment of the disease's individual fall risk, the severity of the dis-ease, and the prognosis of progression. The TWT covers various aspects of mobility, examines the relationship between cognitive functions and walking, and enables differentiation of the motor phenotypes of PD.

This paper presents two designs of high-efficiency polarizer reflectarray antennas able to generate a collimated beam in dual-circular polarization using a linearly polarized feed, with application to high-gain antennas for data transmission links from a Cubesat. First, an 18 cm x 18 cm polarizer reflectarray operating in the 17.2 - 22.7 GHz band has been designed, fabricated and tested. The measurements of the prototype show an aperture efficiency of 52.7% for right-handed circular polarization (RHCP) and 57.3% for left-handed circular polarization (LHCP), both values higher than those previously reported in related works. Then, a dual-band polarizer reflectarray is presented for the first time, which operates in dual-CP in the frequency bands of 20 and 30 GHz. The proposed antenna technology enables a reduction of the complexity and cost of the feed chain to operate in dual-CP, as a linear-to-circular polarizer is no longer required. This property, combined with the lightweight, flat profile and low fabrication cost of printed reflectarrays, makes the proposed antennas good candidates for Cubesat applications.

The aim of this work was to investigate the microstructure and the mechanical properties of la-ser-welded joints combined of DP800 and DP1000 high strength thin steel sheets. The welded joints (WJ) comprised of similar/dissimilar steels with similar/dissimilar thickness were consisted of different zones and exhibited similar microstructural characteristics. The trend of microhard-ness for all WJs was consistent, characterized of the highest value at hardening zone (HZ) and lowest at softening zone (SZ). The degree of softening was more severe and the size of SZ was wider in the WJ combinations of DP1000 than DP800. The tensile test fractures were located at the base material (BM) for all DP800 weldments, while the fractures occurred at the fusion zone (FZ) for the weldments with DP1000 and those with dissimilar sheet thicknesses. The DP800-DP1000 weldment presented similar yield strength (YS) and ultimate tensile strength (UTS) values but lower elongation (EI) in comparison with the DP800-DP800 weldment, which showed similar strength properties as the BM of DP800. However, the EI of DP1000-DP1000 weldment was much lower in comparison with the BM of DP1000. The DP800-DP1000 weldment with dissimilar thicknesses showed the highest YS and UTS values compared with the other weldments, but with the lowest EI. The fatigue fractures occurred at the WJ for all types of weldments. The DP800-DP800 weldment had the highest fatigue limit and DP800-DP1000 with dissimilar thick-nesses had the lowest fatigue limit. The fatigue crack initiated from the weld surface.

Dual-method use is the most reliable form of protection against unintended pregnancies and HIV/STIs. Although dual-method use remains uncommon among women in stable relationships, some women do practice it. In this study, we explored the barriers that make dual-method use rare and the behaviors of women who practice dual-method use using a positive deviance framework in Uganda. We screened 150 women using highly effective contraceptives at five health facilities. We identified nine women who practiced dual-method use and 141 women who did not. In a qualitative study, we conducted in-depth interviews with all nine women practicing dual-method use and 10 women randomly selected out of the 141 who did not. We performed a thematic analysis using the positive deviance framework. Regardless of practicing dual-method use or not, women faced perceived barriers against dual-method use, such as partner’s objection, distrust, shyness about introducing condoms into marital relationships, and limited access to condoms. However, women practicing dual-method use had higher levels of risk perception about unintended pregnancies and HIV/STIs. They also engaged in unique behaviors, such as influencing their partners’ condom use by initiating discussions, educating their partners on sexual risks and condom use, and obtaining condoms by themselves. These findings will be useful in developing effective community-led and peer-based interventions promoting dual-method use to reduce the dual burden of unintended pregnancies and HIV/STIs among women in Uganda.

Hot deformation at elevated temperature is essential to densify the particle reinforced Aluminum matrix composites (AMCs) and improve their performance. However, hot deformation behavior of the AMCs is sensitive to the variation of hot processing parameters. In this paper, optimal processing parameters of the dual-scale SiCp/A356 composites was determined to explore the control strategy of the microstructure. Hot compression tests were conducted at the temperature ranging from 460 to 520℃ under strain rates from 0.01 to 5 s−1. Constitutive equation and processing maps were presented to determine the hot processing parameters. Microstructure evolution of the dual-scale SiCp/A356 composites was analyzed. The strain rate of 0.62 ~ 5s-1 and deformation temperature of 495 ~ 518℃ is suitable for the hot processing. The number of DRX grains in the “safe” domains is larger and the dislocation density is lower compared to those of instability domains. DRX particles mainly occurred around SiC particles. The presence of SiC particles can promote effectively the DRX nucleation, which result in that the dynamic softening mechanism of the dual-scale SiCp/A356 composites is dominated DRX.

Vertical-channel organic dual-gate/base transistors would be highly interesting since vertical organic transistors are the fastest organic transistors demonstrated today. However, incorporating a dual gate/base structure into an ultra-short channel vertical architecture represents a substantial challenge. Here, we successfully realize a new device concept of vertical organic permeable dual-base transistors (OPDBTs), where either of both base electrodes can be used to change the on-currents and tune the threshold voltages. The optimized devices yield a high on-current density of 1.54 A cm^-2 and a large current gain of 9.2×10⁵, corresponding to a high transmission value of 99.998%. The detailed operation mechanisms are investigated by calibrated TCAD simulations with the Poole-Frenkel mobility model, Gaussian density of states and tunneling model. Finally, high-performance logic circuits, e.g. inverter, NAND/AND computation functions are demonstrated with one single OPDBT operating at supply voltages of < 2.0 V. We believe that OPDBTs offer a compact and technologically simple hardware platform with excellent application potential for vertical-channel organic transistors in complex logic circuits.

Lithium-ion batteries have attracted enormous interests recently as promising power sources. However, the safety issue associated with the employment of highly flammable liquid electrolyte impedes the further development of next-generation lithium-ion batteries. Recently, researchers reported the use of electrospun core-shell fiber as the battery separator consisting of polymer layer as protective shell and flame retardants loaded inside as core. In case of a typical battery shorting, the protective polymer shell melts during thermal-runaway and the flame retardants inside would be released to suppress the combustion of the electrolyte. Due to the use of a single precursor solution for electrospinning containing both polymer and flame retardants, the weight ratio of flame retardants is limited and dependent. Herein, we developed a dual-nozzle, coaxial electrospinning approach to fabricate the core-shell nanofiber with a greatly enhanced flame retardants weight percentage in the final fibers. The weight ratio of flame retardants of triphenyl phosphate in the final composite reaches over 60 wt.%. The LiFePO4-based cell using this composite nanofiber as battery separator exhibits excellent flame-retardant property without compromising the cycling stability or rate performances. In addition, this functional nanofiber can also be coated onto commercial separators instead of being used directly as separators.

We construct families of ground state representations of the U(1)-current net and of the Virasoro nets Vir_c with central charge c ≥ 1. We show that these representations are not covariant with respect to the original dilations, and those on the U(1)-current net are not solitonic. Furthermore, by going to the dual net of with respect to the ground state representations of Vir_c, one obtains possibly new family of Möbius covariant nets on S¹.

Objective: To evaluate three different microincisional ab interno trabeculectomy procedures in a porcine eye perfusion model. Methods: In perfused porcine anterior segments, 90 degrees of trabecular meshwork (TM) were ablated using the Trabectome (T; n = 8), Goniotome (G; n = 8), or Kahook device (K; n = 8). After 24 hours, additional 90 degrees of TM were removed. Intraocular pressure (IOP) and outflow facility were measured at 5 µL/min and 10 µL/min perfusion to simulate an elevated IOP. Structure and function were assessed with canalograms and histology. Results: At 5 µL/min infusion rate, T resulted in a greater IOP reduction than G or K from baseline (76.12% decrease versus 48.19% and 47.96%, P = 0.013). IOP reduction between G and K was similar (P = 0.420). Removing another 90 degrees of TM caused an additional IOP reduction only in T and G but not in K. Similarly, T resulted in the largest increase in outflow facility at 5 µL/min compared with G and K (first ablation: 3.41 times increase versus 1.95 and 1.87; second ablation: 4.60 versus 2.50 and 1.74) with similar results at 10 µL/min (first ablation: 3.28 versus 2.29 and 1.90 (P = 0.001); second ablation: 4.10 versus 3.01 and 2.01 (P = 0.001)). Canalograms indicated circumferential flow beyond the ablation endpoints. Conclusions: T, G and K significantly increased the outflow facility. In this model, T had a larger effect than G and K.

Marine renewable energy is emerging as one of the fast-growing industry in the last decades, as modern society pushes for technologies that can convert energy contained from winds, waves, tides and stream flows. The implementation of renewable energy technologies impose high demands on both structural and environmental engineering, as the energy converters have to work under extreme conditions where parameters such as sea-bottom configuration, water transparency and depth, sea-states and prevailing winds are harsh. Constant monitoring of the marine environment is crucial in order to keep this sector reliable. Active acoustics is becoming a standard tool to collect multi-dimensional data from physical, geological and biological properties of the marine environment. The Div. of Electricity of Uppsala University have been developing an environmental monitoring platform based on sonar (Sound Navigation And Raging) systems. This platform aims to monitor the installation, operation and decommissioning of marine renewable energy converters. The focus will be given the observations of behaviours of marine animals in vicinity of energy converters but also structural inspection and monitoring of MRETs. This paper describes how this multifunctional environmental monitoring platform come to existence from the design to the deployment phase.

The emergence of electric vehicles has brought new issues such as the problem of rolling element bearings (REBs) operating at high speeds. Losses due to these components in mechanical transmissions are a key issue and must therefore be taken into account right from the design stage of these systems. Among these losses, the one induced by the motion of rolling elements , known as drag loss, becomes predominant in high-speed REBs. Although an experimental approach is still possible, it is difficult to isolate this loss in order to study it properly. A numerical approach based on CFD is therefore a possible way forward, even if other issues arise. The aim of this article is to study the ability of such an approach to correctly estimate the drag coefficient associated with the motion of rolling elements. The influence of the numerical domain extension, the mesh refinement, the simplification of the ring shape and the presence of the cage, on the values of the drag coefficient is presented. While it seems possible to compromise on the calculation domain and mesh size, it appears that the other parameters must be taken into account as much as possible to obtain realistic results.

The influence of applied loads on free vibrations analysis of plates and shells panels made of functionally graded materials is analyzed in the present work. Formulations for the static analysis considering geometrically nonlinear behavior, as well as linear buckling and free vibrations analyses are considered. The calculation of the through-thickness stress distribution is also performed. A finite element model based on a higher order shear deformation theory and using a non-conforming triangular flat plate/shell element with 3 nodes, and 8 degrees of freedom per node is used in the numerical implementation. The results obtained with this numerical model are presented, discussed, and compared with alternative solutions published by other authors in some benchmark applications.

The establishment of an isolation layer in submarine mining has long presented an enduring challenge. In the context of this research, we conducted a similarity simulation test to preliminarily ascertain the interplay between the thickness and extent of the isolation layer. Subsequently, we introduce an innovative approach that integrates fractal theory and the bonded block model (BBM) to simulate undersea isolation layer mining. The validation of this method hinges on on-site borehole scanning and displacement monitoring, which serve to depict the intricate fractal evolution of fractures and predict the optimal thickness of the isolation layer. Our findings affirm the robustness and validity of this method. Evaluation of the fractal dimensions of fractures reveals that a critical threshold of 1.7 exists to prevent structural failure of the isolation layer, while a limit of 1.5 is necessary to avert significant water ingress. Remarkably, the correlation dimension of the settlement time series closely aligns with the fractal dimension of the fractures, underscoring the feasibility of ensuring the safety of isolation layer mining through real-time settlement monitoring.

The study proposes a theoretical method for evaluating the 'safety against derailment' indicator of a specialized train composition for the transportation of very long rails. A composition of nine wagons, suitable for the transportation of rails with a length of 120 m, is considered. For the remaining recommended rail lengths, the number of wagons is reduced or increased, the method being modified depending on the required configuration. In accordance with the requirements of EN 14363:2019, the composition is in a curve with a radius of R=150 m. The rails bend, some of them contact the vertical stanchions of the wagon and cause additional transverse forces, which are balanced in the rail track. This is a prerequisite for derailment of the vehicle. The goal of the study is to determine the additional transverse forces that arise because of the bent rails. The task is statically indeterminate, and considering the dimensions of the rails, its solution becomes seriously difficult. For the purposes of the study, the finite element method was used. Based on the displacements of the support points of the rails (caused by the geometry of the curve) the bending line of the elastic load is determined and the forces in the supports are calculated. A group of five rails is considered, with results multiplied proportionally for cases other than five. The resulting forces are considered when determining the derailment safety criterion defined by EN 14363:2019.

Cycloid drives are generally used in precision machinery requiring high reduction ratios, such as robot joint (RV) reducers, in which the contact load and stress property of the internal meshing pairs greatly affect the dynamic transmission performance of the reducers. Therefore, in this study, Isogeometric Analysis (IGA) was employed to explore the multi-tooth contact problem of the cycloid pinwheel drive. Based on the NURBS curved surface generation method, the NURBS tooth profile of the cycloid gear was reconstructed. In addition, the NURBS surface of the cycloid gear - pin tooth - output pin was generated via the element splicing method. A geometrical analysis model of cycloid pinwheel drive was established to solve the contact force of the meshing pair under different input angles, and compared with the finite element method in terms of convergence, resultant accuracy, and solving timeliness. The results show that the Isogeometric analysis has higher accuracy and efficiency than the finite element method in calculating the contact stress and contact force. This method can improve the contact simulation accuracy of the cycloid drive and provides a reference for the design evaluation of RV reducer.

As a new type of gear, bevoloid gears have the advantages of compensating axial error, smooth transmission, and eliminating turning error, and they are widely used in applications requiring high transmission accuracy and stability. However, research on calculating the time-varying mesh stiffness of bevoloid gears is still limited, and there is an urgent need to propose a method that can calculate the stiffness of bevoloid gears quickly and accurately. This paper first establishes the bevoloid gear tooth profile expressions, then assumes a pair of bevoloid gears meshing with the same rack and derives the contact line equations of parallel axis bevoloid gear pairs, and analyze the contact process of bevoloid gears. We propose an analytical algorithm that uses the slicing method to calculate the stiffness of helical gears, straight bevoloid gears, and helical bevoloid gears, change the parameters of helical bevoloid gears respectively, and analyze the influence of different parameters on stiffness. Finally, the finite element method is used to verify the analytical method, and the correctness of the analytical calculation results is verified, and the errors are analyzed.

A complete model was developed to simulate the behavior of a circular clamped axisymmetric fluid-coupled Piezoelectric Micromachined Ultrasonic Transducer (PMUT). Combining Finite Difference and Boundary Element Matrix (FD-BEM), this model is based on the discretization of the partial differential equation used to translate the mechanical behavior of a PMUT. In the model, both the axial and the transverse displacements are preserved in the equation of motion and used to properly define the neutral line position. To introduce fluid coupling, a Green’s function dedicated to axisymmetric circular radiating sources is employed. The resolution of the behavioral equations is used to establish the equivalent electroacoustic circuit of a PMUT that preserves the average particular velocity, the mechanical power, and the acoustic power. Particular consideration is given to verifying the validity of certain assumptions that are usually made across various steps of previously reported analytical models. In this framework, the advantages of the membrane discretization performed in the FD-BEM model are highlighted through accurate simulations of the first vibration mode and especially the cutoff frequency that many other models do not predict. This high cutoff frequency corresponds to cases where the spatial average velocity of the plate is null and is of great importance for PMUT design because it defines the upper limit above which the device is considered to be mechanically blocked. These modeling results are compared with electrical and dynamic membrane displacement measurements of AlN-based PMUTs in air and fluid. This complete PMUT model using the FD-BEM approach is shown to be very efficient in terms of computation time and accuracy.

The electronic, optical, and magnetic properties of Nd-doped ZnO systems were calculated using the DFT/GGA+U method. According to the results, the Nd dopant causes lattice parameter expansion, negative formation energy, and bandgap narrowing, resulting in the formation of an n-type degenerate semiconductor. Overlapping of the generated impurity and Fermi levels results in a significant trap effect that prevents electron-hole recombination. The absorption spectrum demonstrates a redshift in the visible region and improved intensity, leading to enhanced photocatalytic performance. The Nd-doped ZnO system displays ferromagnetic, with FM coupling due to strong spd-f hybridization through magnetic exchange interaction between the Nd-4f state and O-2p, Zn-4s, and Zn-3p states. These findings imply that Nd-doped ZnO may be a promising material for DMS spintronic devices.

One of the most important problems of geotechnical engineering is the design of pile foundations. Piles are generally designed for vertical and horizontal static loads. However, it is important to design piles against dynamic loads in regions with high seismicity. This study verified a centrifuge experiment obtained from the literature with a finite element program. With the kinematic interaction analyses made for this purpose, the effect of parameters such as layered soil, groundwater, pile stiffness, and earthquake acceleration were investigated numerically. According to the results obtained, it was understood that the earthquake magnitude is the most important parameter in kinematic interaction analyses. In addition, in layered soil conditions, the fact that 75% of the pile length is in the weak soil creates the most unfavorable situation. It has been observed that pile stiffness and groundwater level also have certain effects on the kinematic interaction.

The flavor, aroma and color of coffee may change due to mechanical damage, reducing its qual-ity. To measure the mechanical response of materials, compression tests can be performed, de-termining the effect of force application on the mechanical behavior of the fruit at different stages of ripeness. In this context, this study aimed to analyze the deformation, strain energy and equivalent von Mises stress of coffee fruits at mature, semi-mature and immature maturation stages and compressed by collapse forces. Compression in three directions (x, y and z) was sim-ulated on coffee fruit models using the finite element method, with a compression support in the direction opposite to the force application axis. The numerical simulation of the compression process allowed to verify that the more mature the fruit, the greater the associated mean defor-mation (2.20 mm mm-1, 0.78 mm mm-1 and 0.88 mm mm-1), the lower the mean strain energy (0.07 mJ, 0.21 mJ and 0. 34 mJ) and the lower the mean equivalent von Mises stress (0.25 MPa, 1.03 MPa and 1.25 MPa), corresponding to ripe, semi-ripe and immature fruits; and these proper-ties may be used to analyze how processes in the production chain affect the amount of mechan-ical damage.

Emerging soft actuators with various soft materials and traveling-wave motion have been frequently discussed. Various configurations and the resulting performances have been proposed, and it is very challenging for soft actuators in realizing large strokes. This study presents an experimentally validated nonlinear finite element model to predict the deformation produced by a spiral pneumatic rubber actuator to generate traveling-wave motion. The actuator consists of a membrane mounted on a rubber substrate with three air chambers in a spiral configuration, simplifying the actuator's structure. The sequential deformations of the successive chambers interact with each other and produce radial traveling-waves on the membrane surface, driving the objects placed on the actuator. Finite element analysis using ANSYS computer software analyzed the elastic movement by considering the influence of different initial structural types. The structure with three different length ratios was introduced using the four parameters: membrane thickness, chamber width, chamber depth, and wall thickness. The simulation results indicated an optimal structure with specific ratios. A reasonable correlation was obtained during experimental validation; the predicted displacement values were approximately 17% smaller than the experimental values. Finally, the transportation performance of the prototype was tested and a velocity of 2.28 mm/s in the desired direction was achieved. We expect that our demonstration will expand the range of applications of the spiral pneumatic rubber actuator to include conveying or worm-like robots.

The buildup of plaque in the arteries characterizes atherosclerosis, which causes the walls of the arteries to thicken, the lumen to narrow, and the wall to thin in certain areas. These changes can lead to alterations in blood flow, potentially resulting in aneurysms and heart attacks if left untreated. This paper presents a phenomenological model to explain the mechanics of plaque rupture in stenosed bifurcated elastic arteries. The model considers the interaction between the plaque and artery wall, blood flow, mechanical properties of the artery wall and plaque, and hemodynamic forces in the system. Using the Navier-Stokes equations to describe blood flow and elastic properties of artery walls, our study shows that blood flow can become turbulent, leading to backflow, vortices, and possible stagnation. Certain regions can become highly vulnerable and result in elevated heat transfer between blood and arterial walls, which can lead to the rupture of the plaque cap. The study focuses on blood flow features such as velocity profiles and wall displacement on fluid-structure interaction, which are consistent with the literature. Finally, we calculate the wall shear stress (WSS) for minimum and maximum times while considering elastic walls. Our findings may provide valuable insights into the mechanisms of plaque rupture and inform the development of improved diagnostic and therapeutic approaches.

Advanced manufacturing techniques, aimed at implants with high dependability, flexibility, and low manufacturing costs, are crucial in meeting the growing demand for high-quality products like biomedical implants. Incremental sheet forming is a promising flexible manufacturing approach for rapidly prototyping sheet metal components using low-cost tools. Titanium and its alloys are used to shape most biomedical implants because of its superior mechanical qualities, biocompatibility, low weight, and great structural strength. The poor formability of titanium sheets at room temperature, however, limits their widespread use. The goal of this research is to show that gradual sheet formation of a titanium biomedical implant is possible. The possibility of creative and cost-effective concepts for the manufacturing of such complicated shapes with significant wall angles is explored in this study. A numerical simulation based on finite element modeling as well as a design process tailored to metal forming is used to complete the development. The mean of uniaxial tensile tests with a constant strain rate was used to study the flow behavior of the studied material. To forecast the crack, the obtained flow behavior was modeled using the behavior model and failure model.

A connection between the phenomenon of wafer bifurcation and that of spontaneous symmetry breaking (SSB) has been established. Indeed, by developing an analytical approximation of the elastic energy of a wafer coated with a thin layer (e.g. a metal), it is shown as the elastic potential energy, interpreted as a quantity contributing to the thermodynamic free energy, can be investigated within the framework of the Landau theory of the second order phase transitions. The elastic energy of a bifurcated wafer is a complex function of the stress and the curvatures in the two perpendicular directions. In this work, it is shown as a translation of the coordinate system of the curvatures allows to gain a potential which has a “Mexican hat” shape. This is a distinctive trait of the phenomenon of spontaneous symmetry breaking (SSB). Moreover, it is shown as the values of the coordinates at the minimum of the SSB potential agrees with those provided by the theory. Bifurcation is hence a phenomenon that can also be interpreted as a spontaneous symmetry breaking where the rotational symmetry of a disc shaped wafer is broken. It occurs because of a lowering of the wafer energy in the SSB broken symmetry configuration.

With the increasingly stringent airworthiness standards, the noise generated during the rotorcraft flight is gradually attracting people’s attention. It widely operated helicopters at low altitudes because of their maneuverability. The way to reduce the noise caused by the complex airflow of the helicopter rotor system has progressively become a hot topic for researchers. Using a hybrid acoustic analysis method, this paper investigates the improvement of the noise and thrust of the helicopter’s tail rotor through the tail rotor structural parameters. For the basic model, the turbulence simulation is performed using an incompressible detached eddy simulation (DES) method, and the Lighthill acoustic analog equation is calculated using the finite element method (FEM). We verified the accuracy of the method through wind tunnel tests. We chose a series of structural parameters for sound simulation and fluid simulation calculations. The results indicate that the modified tail rotor noise reduced by 16.5 dBA and the total thrust increased by 19.9% from the prototype model. This work can enhance the duct tail rotor design to improve aerodynamic and aeroacoustic performance.

Reliable information on transition matrix elements of various property operators between molecular electronic states is of crucial importance for predicting spectroscopic, electric, magnetic and radiative properties of molecules. The finite-field technique is a simple and rather accurate tool for evaluating transition matrix elements of first-order properties in the frames of the Fock space relativistic coupled cluster approach. We formulate and discuss the extension of this technique to the case of transitions between the electronic states associated with different sectors of the Fock space. Pilot applications to the evaluation of transition dipole moments between the closed-shell-like states (vacuum sector) and those dominated by single excitations of the Fermi vacuum (the $1h1p$ sector) in heavy atoms (Xe, Hg) and simple molecules of heavy element compounds (I${}_2$, TlF) are reported.

A micromechanical model is implemented to indicate the progressive fatigue problem of a laminated composite with a central circular hole under fatigue loading based on a finite element model. The mechanical properties of the composite lamina are represented based on the characteristics of the fiber and the matrix through a micromechanics model. An appropriate algorithm is then adopted to simulate fatigue damage development in the composite lamina. According to this algorithm, the stress field of the composite subjected to fatigue load is initially obtained using the finite element method. Finally, the predicted results of the stresses in the constituents i.e. fiber and matrix are determined according to the micromechanical bridging model. Finally applying proper damage driving relations leads to damage degree in each element. The proposed model is proven to be successful in the observation of the fatigue behavior with stiffness degradation in each element of the composite in each cycle. Results are reported and validated using those micromechanical models and experimental data available in the literature.

In this paper, the results of finite element analyses of a single-layer cylindrical latticed shell under severe earthquake is presented. A 3D Finite Element model using fiber beam elements were used to investigate the collapse mechanism of this type of shell. The failure criteria of structural members are simulated based on the theory of damage accumulation. Severe earthquake of peak ground acceleration (PGA) of 500 gal was applied to the shell. The stress and defeomation of the shell were studied in detail. A three-stages collapse mechanism “double-diagonal -members-failure-belt” of this type of structure was discovered. Based on the analysis results, the measures to mitigate collapse of this type of structure is recomanded.

It is well known that the Continuous Galerkin Finite Element (CGFE) method is globally consistent with respect to the first law of thermodynamics. This means that, for any mesh, all obtained discrete solutions will conserve total energy. One might expect, that the method is, also, globally consistent with respect to the second law of thermodynamics. In this paper, we formally study if such conjecture is true. The heat conduction equation is used as the physical model for this analysis. In the present study it is proved that the conjecture is false: at least, for standard piecewise linear (1D and 2D) elements, the CGFE method is not always globally consistent with respect to the second law of thermodynamics. In other words, some obtained discrete solutions can violate the global postulate of the second law, which asserts that total entropy can never decrease.

Although Cucurbita pepo is one of the most variable species of the plant kingdom, Zucchini morphotype has undergone intensive breeding that has led to a narrow genetic base making the crop vulnerable to pest and diseases. This vulnerability makes the knowledge of resistance genes of utmost importance. In this study, a data mining search of Zucchini summer squash genome database was conducted to identify and annotate members of the NBS-encoding gene family. In order to characterize the retrieved genes in detail, they have been studied in the bases of phylogenetic relationships, structural diversity, conserved protein motifs, gene duplications and promoter region analysis. Our study shows that the NBS-encoding gene family is relatively small in Zucchini (34 members, which are separated into non-TIR- and TIR-NBS-LRR subfamilies) with a significantly lower number of R-genes than in other species. Duplications have not played a major role in the expansion of this type of genes in C. pepo. Among the cis-regulatory elements presented in these sequences, six motifs are over-represented. These elements were reported to be involved in pathogens or plant stress induced responses. These results will contribute to the identification, isolation and characterization of candidate R-genes, thereby providing insight into NBS gene family evolution in the species.

DNA vaccines are stable, safe, cost effective to produce and relatively quick and easy to manufacture. However, to date DNA vaccines have shown relatively poor immunogenicity in humans despite promising preclinical results. Consequently, a number of different approaches have been investigated to improve the immunogenicity of DNA vaccines. These include the use of improved delivery methods, adjuvants, stronger promoters and enhancer elements to increase antigen expression, and codon optimization of the gene of interest. This review describes the creation and use of a DNA vaccine vector containing a porcine circovirus (PCV-1) enhancer element that significantly increases recombinant antigen expression and immunogenicity and allows for dose sparing. A 172bp region containing the PCV-1 capsid protein promoter (Pcap) and a smaller element (PC; 70 bp) within this were found to be equally effective. DNA vaccines containing the Pcap region expressing various HIV-1 antigens were found to be highly immunogenic in mice, rabbits and macaques, at 4 to 10-fold lower doses than normally used and to be highly effective in heterologous prime-boost regimens. By lowering the amount of DNA used for immunization, safety concerns over injecting large amounts of DNA into humans can be overcome.

The paper aims in assessing risks of mandible fractures consequent to impacts or sport accidents. The role of the structural stiffness of mandible, related to disocclusion state, is evaluated through numerical simulations using the finite element method (FEM). It has been assumed that the quasi-static stress field, due to distributed forces developed during accidents, could explain the common types of mandibular fractures. Geometric model of adolescent mandible was built, upon the basis of medical imaging, in CAD software with distinction between cortical layer and inner spongy bone. The finite element model of disoccluded mandible was next created. Mandibular condyles were supposed jammed in the maxillary fossae. The total force of 700 N, simulating an impact on mandible, has been sequentially applied in three distinct areas: centrally, at canine zone and at the mandibular angle. Clinically most frequent fractures of mandible were recognized through the analysis of maximal principal stress and maximal principal strain fields. Mandibular fracture during accidents can be analyzed at satisfactory level using linear quasi-static FE models for designing protections in sport and transport. The proposed approach can be improved by introducing more realistic interactions between condylar processes and fossae.

B chromosomes are supernumerary chromosomes which are found in addition to the normal standard chromosomes (A chromosomes). B chromosomes are well known to accumulate several types of repeats. Although the evolution of B chromosomes has been subject of numerous studies, the mechanisms of accumulation and evolution of repetitive sequences is not fully understood. Recently, new genomic approaches have shed light on the origin and accumulation of different classes of repetitive sequences in the process of B chromosome formation and evolution. Here we discuss the impact of repetitive sequences accumulation on the evolution of plant B chromosomes.

Many dioecious plants have sex chromosomes that are cytologically heteromorphic, but about half of species lack cytological differences between males and females and are thus homomorphic. Very little is known about the size and content of the non-recombining sex-determining region (SDR) in these species. Here, we assess the size and content of the SDR of the diploid dioecious herb Mercurialis annua, which has homomorphic sex chromosomes and shows signatures of mild Y-chromosome degeneration. We used RNAseq to identify new Y-linked markers for M. annua. Twelve of 24 transcripts with male-specific and male-biased expression could only be PCR-amplified from males and are thus Y-linked. We found a further six Y-linked sequences that were present in males but not females using genome capture data from multiple populations. We used the Y-linked sequences to identify and sequence 17 sex-linked bacterial artificial chromosomes (BACs), which form 11 groups of non-overlapping sequence, covering a total sequence length of about 1.5 Mb. Content analysis of this region suggests it is enriched for repeats, has a low gene density and contains few candidate sex-determining genes. The BACs map to a subset of the sex-linked region of the genetic map, which is estimated to be at least 14.5 Mb. This is substantially larger than estimates for other dioecious plants with homomorphic sex chromosomes, especially given the small genome size of M. annua. Our data provide a rare, high-resolution view of the homomorphic Y chromosome of a dioecious plant.

The Inverted F Antenna (IFA) with the parasitic element on a finite conducting plane is proposed in the range frequency of 0.1 to 5.5 GHz and its characteristics are analyzed numerically. In this research, the parasitic element and the main IFA are investigated to obtain the resonance frequency for multiband operation purposes. The parasitic element is placed beneath adjusted to the main IFA to derive more frequency bands. The distance between the parasitic element and main horizontal element extremely affects the performance of the IFA. It is found that when the parasitic element is located closer to the conducting plane, this element is coupled by the current on the conducting plane. Consequently, the return loss bandwidth becomes narrower. Therefore, the gain of the proposed IFA becomes a bit higher. The antenna gain is about 8.21 dB at band #3 (λ_1.747), 7.43 dB at band #5 (λ_2.967) and 8.82 dB at band #6 (λ_4.023). This occurs when the calculation condition is antenna height h1 = 23 mm, h2 = 21 mm, horizontal antenna elements L = 173.2 mm, L1 = 140.9 mm and Lp = 152 mm, shorted element Ls = 30.7 mm, the distance between parasitic element and shorted element pyl = 5 mm. While the size of conducting plane is considered pxp+pxm by pyp+pym as 57.5+57.5 mm by 200+50 mm. In the numerical analysis, the electromagnetic simulator WIPL-D based on Method of Moment is used. The results show that the proposed IFA has UHF and SHF channel receiver which are suitable for advanced wireless service (band #3), mobile phones, Bluetooth, maritime service, radiolocation service (band #5) and radars, mobile phones, commercial wireless LAN (band #6).

Terrestrial LiDAR becomes more and more popular to estimate leaf and plant area density. Voxel-based approaches account for this vegetation heterogeneity and significant work has been done in this recent research field, but no general theoretical analysis is available. Although estimators have been proposed and several causes of biases have been identified, their consistency and efficiency have not been evaluated. Also, confidence intervals are almost never provided. In the present paper, we solve the transmittance equation and use the Maximum Likelihood Estimation (MLE), to derive unbiased estimators and confidence intervals for the attenuation coefficient, which is proportional to leaf area density. The new estimators and confidence intervals are defined at voxel scale, and account for the number of beams crossing the voxel, the inequality of path lengths in voxel, the size of vegetation elements, as well as for the variability of element positions between vegetation samples. They are completed by numerous numerical simulations for the evaluation of estimator consistency and efficiency, as well as the assessment of the coverage probabilities of confidence intervals. • Although commonly used when the beam number is low, the usual estimators are strongly biased and the 95% confidence intervals can be ≈±100% of the estimate. • Our unbiased estimators are consistent in a wider range of validity than the usual ones, especially for the unbiased MLE, which is consistent when the beam number is as low as 5. The unbiased MLE is efficient, meaning it reaches the lowest residual errors that can be expected (for an unbiased estimator). Also the unbiased MLE does not require any bias correction when path lengths are unequal. • When elements are small (or voxel is large), 103 beams entering the voxel leads to some confidence intervals ≈±10%, but when elements are larger (or voxel smaller), it can remain wider than ±50%, even for a large beam number. This is explained by the variability of element positions between vegetation samples. Such a result shows that a significant part of residual error can be explained by random effects. • Confidence intervals are much smaller (±5 to 10%) when LAD estimates are averaged over several small voxels, typically within a horizontal layer or in the crown of individual plants. In this context, our unbiased estimators show a reduction of 50% of the radius of confidence intervals, in comparison to usual estimators. Our study provides some new ready-to-use estimators and confidence intervals for attenuation coefficients, which are consistent and efficient within a fairly large range of parameter values. The consistency is achieved for a low beam number, which is promising for application to airborne LiDAR data. They entail to raise the level of understanding and confidence on LAD estimation. Among other applications, their usage should help determine the most suitable voxel size, for given vegetation types and scanning density, whereas existing guidelines are highly variable among studies, probably because of differences in vegetation, scanning design and estimators.

Due to the demands of personal travels and entertainments, light airplanes and small business aircrafts are developing rapidly. Light airplane structure is simple; however, it lacks crashworthiness design, especially the considerations on the impact of energy absorption. Therefore, in an event of accident, significant damage to passengers will be usually incurred. Airplanes made of composite materials structurally have high specific strength and good aerodynamic configuration. These materials have become the primary choice for new airplane development. This study mainly explores the topology optimization analysis of the light aircraft’s cockpit made of carbon fiber reinforced composites. This paper compares the compression amounts in the original models of composite material and aluminum alloy fuselages with the models after optimization during the crash-landing, in order to investigate the safety of fuselages made of different materials after structural optimization under the dynamic crashing. This study found that the energy absorbed by the aluminum alloy fuselage during crash-landing is still higher than that by the carbon fiber reinforced composites fuselage. On the other hand, the aluminum alloy fuselage after topology optimization could have an energy absorption capability enhanced by 40%, as compared to the that of the original model of aluminum alloy fuselage.

In this paper, dual-rotor counter-rotating (CR) configurations of vertical axis wind turbines (VAWT) are briefly inspected and divided into three types. This investigation was focused on one of these types – the CR-VAWT with co-axial rotors, in which two equal rotors are placed on the same shaft, displaced from each other along it and rotate in opposite directions. For this CR-VAWT with three-blade H-Darrieus rotors, the properties of the design in terms of aerodynamics, mechanical transmission and electric generator, as well as control system are analyzed. A new direct-driven dual-rotor (DR) permanent magnet synchronous generator (PMSG) was proposed, in which two built-in low-power PM electric machines have been added. They perform two functions – start-up and overclocking of the rotors to the angular velocity at which the lifting force of the blades is generated and stabilizing the CR-VAWT work as wind gusts act on the two rotors. Detailed in this paper is the evaluation of aerodynamic performance of the CR-VAWT via 3D computational fluid dynamics (CFD) simulations. The evaluation was conducted using the CONVERGE CFD software with the inclusion of the actuator line model for the rotor aerodynamics, which significantly reduces the computational effort. Obtained results show that both rotors, while they rotate in opposite directions, had a positive impact on each other: the power coefficients of the upper and lower rotors in the CR-VAWT increased by 5.5% and 13.3% respectively compared to the single-rotor VAWT at the optimal distance between the rotors of 0.3 from a rotor height.

Due to growing environmental concerns and stringent emissions regulations, optimizing the fuel consumption of marine propulsion systems is crucial. This work deals with the potential in an LNG ship propulsion system to reduce fuel consumption through controlled load distribution between engines in Dual Fuel Diesel Electric (DFDE) plant. Based on cyclical data acquisitioning measured on board and using an optimization model, the study evaluates different load distribution strategies between set up according to the optimization model results and automatic (equal) operation to determine their effectiveness in improving fuel efficiency. The analysis includes scenarios with different fuel types, including LNG, MDO and HFO, at different engine loads. The results indicate that load distribution adjustment based on the optimization model results significantly improves fuel efficiency compared to conventional methods of uniform load distribution controlled by power management systems almost in all load intervals. This research contributes to the maritime industry by demonstrating that strategic load management can achieve significant fuel savings and reduce environmental impact, which is in line with global sustainability goals. This work not only provides a framework for the implementation of more efficient energy management systems on LNG vessels, but also sets a benchmark for future innovations in maritime energy optimization as well as in the view of exhaust emission reduction.

Preterm infants have increased body adiposity at term equivalent age and risk for adverse metabolic outcomes. The aim of the study was to define how nutrient intake may impact body composition (BC) of very low birth weight infants fed with early progressive enteral feeding and standard fortification. Eighty-six infants with

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Banana (Musa spp.) is an important crop to the economies of many developing countries. In the north of Argentina, a sub-tropical region, banana plants grow in a suboptimal environment that limits yield because only one harvest per year is achieved. The objective of this work was to characterize the agroecological aptitude of Formosa, Argentina, for banana production, through the behavior of three varieties of international use: Willians, Jafa and Gran Enano, evaluated during five consecutive campaigns. The three-way data analysis technique called Multiple Factor Analysis (MFA) was used for evaluating varieties’ performances across cycles of production. The results allowed inferring the existence of genotype x environment (GEI) interaction, corroborated by two-way factorial ANOVA. In order to determine how this suboptimal environment affects the development of each genotype of this perennial crop, Dual Multiple Factor Analysis (DMFA) was applied to jointly analyze the correlation structure among traits contributing to the performance of each variety at each campaign. The correlation structures between variables were different in each population and varied among campaigns. All traits showed a great variation across years and genotypes, the fruit peel thickness being the most discrepant throughout the campaigns. However, Formosa appeared as a promising subtropical agroecological environment to produce banana because varieties’ performances were acceptable for large scale production systems. In addition to evaluating the adequate aptitude for cultivating banana in Formosa considering the significant effect of GEI, this research makes a methodological contribution by proposing the use of three-way data analysis MFA and DMFA in Agronomy Science.

This review delves into the significance of chemical communication in mammals, with an emphasis on the role of the vomeronasal system in sensing pheromone-mediated interactions. The vomeronasal system shapes a variety of social and sexual behaviors, including reproduction, hierarchy formation, maternal bonding, and species recognition. Intriguingly, this system presents a vast degree of evolutionary variability, more so than variations observed in the olfactory system. This adaptive diversity underscores the challenges in studying the vomeronasal system, emphasizing the need for detailed research into its neuroanatomy and functional morphology. This review traverses an array of topics central to our understanding of chemical communication in mammals. We begin with the foundational role and basic concepts of chemocommunication. This is followed by an in-depth exploration of the olfactory systems. Subsequently, the neuroanatomical underpinnings of the vomeronasal system are juxtaposed against those of the olfactory system. Our focus then shifts to an exhaustive study of the sensory element of the vomeronasal system, the vomeronasal organ, and the integrating center of this information, the accessory olfactory bulb. The discussion extends to secondary projections of both the olfactory and vomeronasal systems in the light of the dual olfactory hypothesis. The review culminates with a detailed look at four specific models of vomeronasal system organization belonging to four evolutionarily distinct mammalian families: rodents, marsupials, herpestids, and bovids. These have been meticulously analyzed by the authors, aiming to spotlight the significant morphofunctional differences stemming from the adaptive changes imprinted on the system.