Microfiltration membranes derived from semi-crystalline polymers face various challenges when synthesized through the extrusion–casting technique, including the use of large quantities of polymer, long casting times, and the generation of substantial waste. This study focuses on synthesizing these membranes using spin-casting followed by stretch-induced pore formation. Recycled high-density polyethylene (HDPE) and virgin polyethylene powder, combined with a calcium carbonate filler, were used as the source materials for the membranes. The influence of the polymer-filler ratio with and without stretching on the morphology, tensile strength, and water flow rate was investigated. Optimal conditions were determined, emphasizing a balance between pore structure and mechanical integrity. The permeable membrane possessed a mean pore diameter of 500 nm, exhibited a tensile strength measuring 32 MPa, allowed water to flow at a rate of 19 ml/min, and had a water contact angle of 126°. These membranes effectively eliminated suspended particles from water, with their performance evaluated against that of commercially available membranes. This research outlines a synthesis route for microfiltration membranes tailored to semi-crystalline polymers and their plastic forms, utilizing the spin-casting technique.

Nystagmus induced by applying an intense vibratory stimulus to the skull (SVIN) indicates vestibular functional asymmetry. In unilateral vestibular loss, a 100-Hz bone-conducted vibration given to either mastoid immediately causes a primarily horizontal nystagmus. Test is performed in darkness to avoid visual fixation (VF) but there is no data about how much VF affects the often-intense SVIN. The aim is to analyze the amount of reduction of SVIN when VF is allowed during testing. Thus, all patients seen in a tertiary hospital for vertigo or dizziness with positive SVIN were included. SVIN was recorded for 10 seconds for each condition: without VF (aSVINwo) and VF (aSVINw). We obtained an aSVINwo and aSVINw as average slow-phase velocities (SPV) without and with VF. VF index (FISVIN) was calculated as the ratio of SPV. Among the 124 patients included, spontaneous nystagmus (SN) was found in 25% and the mSPV (without VF) of SN was 2.62.4º/s. Mean FISVIN was 0.270.29. FISVIN was 0 in 42 patients and >0 FISVIN <1 in 82 (mean FISVIN 0.390.02). Fixation suppression was found in all patients with SVIN in cases of peripheral vestibulopathy. FISVIN clearly delineates two populations of patients: with or without complete visual reduction of nystagmus.

In this work, we explore the ability to dynamically group the Wind Turbine (WT) of a Wind Farm (WF) based on the behaviour of some of their Supervisory Control And Data Acquisition (SCADA) signals to detect the turbines that exhibit abnormal behaviour. We centre this study on a small WF of five WTs. We use the fact that the same signals from different turbines in the same WF coherently evolve temporally in a time domain, describing very similar waveforms. In this contribution, we use averaged signals from the SCADA system and omit maximums, minimums and standard deviations, focusing mainly on velocities and other slowly varying signals. For the temporal analysis, sliding windows of different temporal durations and overlapings are explored. The capability to automatically identify WTs whose signals differ from the group’s behaviour can alert and program preventive maintenance operations on such WTs before a major breakdown occurs.

Alzheimer’s disease (AD), the most common cause of dementia, is characterized by disruptions in memory, cognition, and personality, significantly impacting morbidity and mortality rates among older adults. However, the exact pathophysiological mechanism of AD remains unknown, and effective treatment options for AD are still lacking. Human induced pluripotent stem cells (iPSC) are emerging as promising platforms for disease research, offering the ability to model genetic mutations associated with various conditions. Patient-derived iPSCs are useful for modeling neurodegenerative and neurodevelopmental disorders. In this study, we generated AD iPSCs from peripheral blood mononuclear cells obtained from a 65-year-old patient with AD carrying the E682K mutation in the amyloid precursor protein (APP) gene. Cerebral organoids derived from AD iPSCs recapitulated the AD phenotype, exhibiting significantly increased levels of tau protein. Our analysis revealed that an iPSC disease model of AD is a valuable assessment tool for pathophysiological research and drug screening.

In recent decades the Mediterranean area observed an increase in large fires, despite the decrease in the number of fire ignitions, following a worldwide tendency. Climate change has been the main culprit for large burnt areas, and alterations of forest ecosystems, resulting in the increased recurrence of forest fires. In Portugal, the analogous trend resulted in the destruction of large rural, urban and industrial areas, where after the 2017 months of June and October catastrophic events, the government implemented the 2019 specific policies for preventing fire outbreaks and defending the forest against fires. This compulsory policy demanded that landowners and local governments alike needed to contact specific authorities requesting authorization for their intentions to clean properties in and around urban areas, roads, and forest limits. Despite policy and careful monitoring, ignitions still occur, and in many cases resulting from the implementation of such policies. The study analyses the before and after policy implementation, considering 6904 ignitions records from the period between 2014 and 2023 from the central area of Portugal, covering the transition area between the agricultural fields of the Tagus valley and the Monte-junto-Estrela Mountain range, the district of Santarém. The authorization to use fire in clearance practices is granted according to a set of weather conditions, temperature, wind intensity, and relative humidity, when analyzing fire ignitions with the average daily wind intensity at the site of the occurrence, we observed that more than half of wildfires occur on days with winds between 10 and 20 Km/h, whereas intensities greater than 30 Km/h only 1% of the total occurrences, and of these 22% occurred due to the use of fire in the burning of agricultural leftovers and cut and piled bushes. The circulation of the thermal depression in the Iberian Peninsula gives rise to increasing intensity throughout the day, reaching a maximum in the late afternoon, this factor combined with the misjudgment of safe conditions leads us to suggest stricter intervals and the need for awareness of daily variation in conditions.

The growing urgency for sustainable energy solutions necessitates a deeper understanding of the environmental impacts of renewable technologies. This article aims to synthesize and analyze Life Cycle Assessments (LCA) in this domain, providing a comprehensive perspective. We systematically categorize 2,923 articles into four communities: (1) Photovoltaic systems, (2) Wind energy systems, (3) Materials for auxiliary industry of photovoltaic and wind systems, and (4) Solar thermal systems. A comparative analysis is conducted to identify methodological consistencies and disparities across these communities. The findings reveal diverse methodological approaches and a range of environmental impacts, highlighting the complexities in assessing renewable energy systems. The article underscores the significance of material selection in photovoltaic and wind systems, providing a critical overview of the current state of LCA research in renewable energy and stressing the need for standardized methodologies. It also identifies gaps in recent research, offering insights for future studies focused on integrating environmental, economic, and social considerations in renewable energy assessments.As a case study, an LCA was used to evaluate two energy supply methods for a sensor network: one connected to the public grid and another powered by a photovoltaic panel. The off-grid system, while more environmentally friendly by reducing reliance on non-renewable energy sources, posed challenges due to the high environmental impact of battery production and disposal. Integrating environmental assessments provides a robust framework for making informed decisions on sustainable technologies. The findings are critical for projects that balance technological needs with sustainability goals.

To reduce the cost of small wind turbines, a prototype of a butterfly wind turbine (6.92 m in diameter), a small vertical-axis type, was developed with many parts made of extruded aluminum suitable for mass production. An over-speed control system with movable arms that operated using centrifugal and aerodynamic forces was installed for further cost reduction. Introducing this mechanism eliminates the need for large active brakes and expands the operating wind speed range of the wind turbine. However, although the mechanism involving the use of only bearings is simple, the violent movement of the movable arms can be a challenge. To address this in the present study, dampers were introduced on the movable arm rotation axes to improve the movement of the movable arms. To predict the behavior of a movable arm and the performance of the wind turbine with the mechanism, a simulation method was developed based on the blade element momentum theory and the equation of motion of the movable arm system. Comparison of experiments and predictions with and without dampers demonstrated qualitative agreement. In the case with dampers, measurements confirmed the predicted increase in the rotor rotational speed when the shorter ailerons installed perpendicularly to the movable arms were used to achieve the inclination. The movable arm system with dampers is expected to be a useful device for vertical-axis wind turbines that are difficult to control.

Deterministic simulations using the SWAN model were conducted along a stretch of the Tietê-Paraná waterway in the Ilha Solteira dam reservoir, São Paulo, Brazil, to assess the water waves generated by winds. Simultaneously employs a probabilistic metamodeling approach (PCE) and Sobol indices, to quantify uncertainty of the five involved physical parameters (wind velocity and direction, bottom friction (JONSWAP), whitecapping and depth-induced breaking index). In the deterministic part, Janssen’s formulation yielded the most successful and accurate estimations of wave heights. Probabilistic analysis underscored the importance of wind data and the whitecapping parameter in model calibration, with a significant influence of wind speed indicated by Sobol indices. The results not only refined the model calibration process, but also allowed the creation of contour maps for wave height and period that offer practical pre-project applications. This work advances understanding of wind wave hydrodynamics deterministically and probabilistically, with good concordance and performance indices compared to field data, despite being scarce.

A joint analysis of solar wind, geomagnetic field, and earthquake catalog data showed that before the catastrophic M7.8 and M7.5 Kahramanmaras earthquake sequence on February 6, 2023, the closed strong magnetic storm occurred on November 7, 2022, SYM/H=-117 nT. Storm started at 08:04 UT. At this time, the high latitudinal part of Turkey's longitudinal region of future epicenters was located under the polar cusp, where the solar wind plasma would directly access the Earth's environment. The time delay between storm onset and earthquake occurrence was ~91 days. We analyzed all seven strong (M7+) earthquakes from 1967 to 2020 to verify the initial findings. A similar pattern has been revealed for all events. The time delay between magnetic storm onset and earthquake occurrence varies from some days to some months. To continue these investigations, a retrospective analysis of seismic and other geophysical parameters just after preceded geomagnetic storms in the epicenter areas is desirable.

The tumor necrosis factor receptor associated factor 1 (TRAF1) plays a key role in promoting lymphocyte survival, proliferation, and cytokine production. Recent evidence showed that TRAF1 plays opposing roles in monocytes and macrophages where it controls NF-B activation and limits pro-inflammatory cytokine production as well as inflammasome-dependent IL-1 secretion. Importantly, TRAF1 polymorphisms have been strongly linked to an increased risk of rheumatoid arthritis (RA). However, whether and how TRAF1 contributes to RA pathogenesis is not fully understood. Moreover, investigating the role of TRAF1 in driving RA pathogenesis is complicated by its multifaceted and opposing roles in various immune cells. In this study, we show that intraarticular injection of TRAF1 deficient macrophages into knee joints of wildtype (WT) mice subjected to the collagen antibody induced arthritis (CAIA) model of RA significantly exacerbated joint inflammation, immune cell infiltration and tissue damage compared to mice injected with WT macrophages. This study may lay the groundwork for novel therapies for RA that target TRAF1 in macrophages.

Background: Tachycardia-induced cardiomyopathy (TIC) is caused by prolonged tachycardia leading to left ventricular dilatation and systolic dysfunction with heart failure. Although TIC is more common in adult, it is rare in early infant. Methods: Clinical testing was performed as part of medical evaluation and management. Next gene se-quencing (NGS) was performed for a patient with TIC. Literature review about TIC was con-ducted. Results: The case was a 5-month-old infant referred the hospital due to symptoms with heart failure at least lasting two months. Heart rate was 200 beats per minute, left ventricular ejection fraction fell below 14%, and electrocardiograms showed atrial flutter, suggesting TIC. After cardiover-sion, there was no recurrence of atrial flutter, and cardiac function was improved at 98 days after tachycardia arrest. There were no pathogenic variants identified according to NGS. Literature review identified 8 early infantile cases with TIC reported. However, there were no previous re-ports such as our case with longer duration of TIC. Conclusions: Improvement of cardiac function depends on the duration of TIC. TIC should be considered in all patients with a dilated cardiomyopathy of uncertain origin and who have tachycardias such as atrial flutter.

The sustainable development of an area is highly dependable on reliable electrical energy supply. Microgrids are important in integrating distributed energy resources (DERs) using power electronic converters. However, microgrid control becomes challenging with the increasing number of distributed generators and loads. With the conventional droop control method, power contributions from DER converters cannot be accurately shared due to a mismatch of line impedances. In this paper, an augmented hierarchical control mechanism is proposed to solve the issues mentioned above. This hierarchical control mechanism consists of primary and secondary controllers. The primary stage utilized the droop controller to improve optimal power flow, mainly for the resistive network. The secondary stage is based on an improved methodology to compensate for the voltage and frequency variations during small and large signal disturbances. Moreover, the modelling and analysis for PMSG-based wind energy conversion systems are also presented. The response of the primary controller for the active and reactive power sharing is investigated. The analysis emphasizes the demonstration of optimal power-sharing under normal and abnormal conditions for the considered load. Finally, the suggested robust controller's performance is evaluated in MATLAB environment and simulation results show the proposed scheme's superiority under different operating conditions.

This study aims to demonstrate the possibility of incorporating a natural antioxidant biomolecule, into polymeric porous scaffolds. To this end, Poly-L-Lactic Acid (PLLA) scaffolds were produced using the Thermally Induced Phase Separation (TIPS) technique and additivated with different amounts of Rosmarinic Acid (RA). The scaffolds, with a diameter of 4 mm and a thickness of 2 mm, were characterized with a multi-analytical approach. Specifically, Scanning Electron Mi-croscopy analyses demonstrated the presence of an interconnected porous network, character-ized by a layer of RA at the level of the pore’s surfaces. Moreover, the presence of RA biomole-cules increased the hydrophilic nature of the sample, as evidenced by the decrease in contact angle with water from 128° to 76°. This approach is cost-effective, and it could be customized with different biomolecules, offering the possibility of producing porous polymeric structures con-taining antioxidant molecules. These scaffolds meet the requirements of tissue engineering and could be offered a potential solution to reduce inflammation associated with scaffold implantation thus improving tissue regeneration.

Heart failure (HF) is a life-threatening disorder and is treated by drug therapies and surgical interventions such as heart transplantation and left ventricular assist device (LVAD). However, these treatments can lack effectiveness in the long term and are associated with issues such as donor shortage in heart transplantation, and infection, stroke, or gastrointestinal bleeding in LVADs. Therefore, alternative therapeutic strategies are still needed. In this respect, stem cell therapy has been introduced for the treatment of HF and numerous preclinical and clinical studies using various types of stem cells, such as embryonic stem cells (ESCs) and induced pluripotent stem cells (iPSCs) have been shown to improve cardiac function and attenuate left ventricular remodeling. IPSCs, which have a capacity of unlimited proliferation and differentiation to cardiomyocytes, are a promising cell source for myocardial regeneration therapy. This review discusses the current status of cardiac regenerative therapy using iPSCs.

This study aimed to evaluate a cantilever beam-type piezoelectric energy harvester operating on train-induced vibrations for powering Wireless Sensor Networks (WSNs) used in railway track monitoring systems. The harvester's behaviors under different conditions are simulated in MATLAB using the analytical model. Natural frequency, maximum deflection, and stress were calculated with greater precision using eigenfrequency and stationary analysis using COMSOL Multiphysics. At a base excitation of 2 g and a resonant frequency of 4.38 Hz, the simulated results showed that the developed energy harvester prototype could generate up to 14 V of AC output voltage and 550 mW of output power. These findings highlight the promising potential of the proposed energy harvester for transforming train mechanical energy into electrical power. This energy harvester's viability and dependability for real-world applications in monitoring railway tracks are supported by developed analytical and simulation models.

The sound power LW of wind turbines (WTs) over the past decades has developed in relation to their electric power P as LW ∝ logP. The spectral distribution of the sound did not change significantly over time. This applies to the average performance of wind turbines, with differences between individual WT types. Because of the expected growth of onshore wind energy, a greater number of people will be living close to wind farms. This sustains the need for sound reduction. Sound reduction measures, such as serrations, reduced tip speed and low noise modes, may counteract the development of higher sound power from ever bigger WTs. To investigate this, the sound production of WT types over the last decades is analysed in relation to their size and electric power and the application of sound reduction measures. The analysis includes the broad band A-weighted and low frequency sound power levels as well as more detailed spectral distributions. Results show that the sound power level of wind turbines above 3 MW on average increases less with size than smaller turbines did. This is due to a lower blade tip speed and the use of sound reducing serrations. The spectral content of wind turbine sound, including the lower frequencies, has not changed significantly.

Globally, habitat fragmentation has increased the proximity between wildlife, humans, and emerging predators such as free-ranging dogs. In these fragmented landscapes, encounters between primates and dogs are escalating, with primates often falling victim to dog attacks while navigating patchy landscapes and fragmented forests. We aim to investigate how these primates deal with the simultaneous threats posed by humans and predators, specifically focusing on the adaptive strategies of Central Himalayan Langur (CHL) in the landscape of fear. To address this, we conducted a behavioral study on the CHL in an agro-forest landscape, studying them for a total of 3912 hours over two consecutive years. Our results indicate that, compared to their most common resting behavior, CHL allocate more time to feeding and locomotion, and less time to socializing in the presence of humans and predatory dogs. Additionally, they exhibit increased feeding and locomotion and reduced social behavior in agro-forest or open habitats. These behavioral patterns reflect adaptive responses to the landscape of fear, where the presence of predators significantly influences their behavior and resource utilization. This study suggests measures to promote coexistence between humans and wildlife through the integration of effective management strategies that incorporate both ecological and social dimensions of human-wildlife interactions.

Crystallization of glass through conventional thermal annealing in a furnace is a well-understood process. However, crystallization by femtosecond (fs) laser brings another dimension to this process. The pulsed nature of the irradiation necessitates a reevaluation of parameters for optimal crystallization and to understand the particularities in the case of using fs laser. This includes adjusting the laser pulse energy, the repetition rate, and the writing speed to either initiate nucleation or achieve substantial crystal growth. Therefore, a key challenge to this work is to establish reliable calculations for understanding the relation of the size of the crystallized region with respect to an ongoing transition (e.g., solid-to-solid, liquid-to-solid), and accounting for the aforementioned laser parameters. In this context and based on previous work, we simulate a temperature distribution (in space and time) to model the thermal treatment at any point in the glass. By setting the condition that the temperatures are between the glass transition and melting temperature, we can deduce the crystallized region size to be compared with experimental observations. For that purpose, the knowledge of the beam width at the focal point and of the absorbed beam energy fraction are critical inputs that were extracted from experiments found in the literature. After that, management of the crystallization process and the width of the crystallization line can be achieved according to pulse energy e.g. crystallite size, and also the effect of the scanning speed can be understood. Among the main conclusions to highlight, we disclose the laser conditions that determine the extent of the crystallized area and deduce that it is never interesting to increase the pulse energy too much but rather the repetition rate for uniform crystallized line.

Earthquake-triggered landslides are one of the most significant hazards worldwide. These landslides, involving small or large volumes, can develop in debris flow or avalanche with high mobility and long-runout distance. The motion processes of this kind of landslide also quite complicated. This study reproduced the motion processes of two landslides using the LS-RAPID program. The Aso Bridge landslide occurred on April 16, 2016, with rapid and long-runout distance characteristics. The Kataragai landslide occurred on April 9, 2018, travelling with flow-like behavior. Through field investigations and laboratory experiments, features and mechanical parameters of these two landslides were obtained. In the LS-RAPID program, the pre-failure models and motion processes of these two landslides were established and reproduced. Results indicated that sliding speed and travelling morphology at different intervals were considered as two indicators to describe their motion process. However, while sliding speed of these two landslides have significant differences with sliding speeds of actual landslides, the final morphologies after failure were consistent with those observed in the field investigation.

Thrombosis is the pathological clot formation under abnormal hemodynamic conditions, which can result in vascular obstruction, causing ischemic strokes and myocardial infarction. Thrombus growth under moderate to low shear (<1000 s^-1) relies on platelet activation and coagulation. Thrombosis at elevated high shear rates (>10,000 s-1) is predominantly driven by unactivated platelet binding and aggregating mediated by von Willebrand factor (VWF), while platelet activation and coagulation are secondary in supporting and reinforcing the thrombus. Given the molecular and cellular level information it can access, multiscale computational modelling informed by biology can provide new pathphysiological mechanisms that are otherwise not accessible experimentally, holding promise for novel first-principle-based therapeutics. In this review, we summarize the key aspects of platelet biorheology and mechanobiology, focusing on the molecular and cellular scale events and how they build up to thrombosis through platelet adhesion and aggregation in the presence or absence of platelet activation. In particular, we highlight recent advancements in multiscale modeling of platelet biorheology and mechanobiology and how they can lead to better prediction and quantification of thrombus formation, exemplifying the exciting paradigm of digital medicine.

Drug-induced liver disease represents one of the main problems in the therapeutic field. As with most pathologies, also in this case various risk factors can be recognised, such as age, sex, but also the gut microbiota. Therefore all drugs on the market can, in fact, cause hepatotoxicity of varying degrees. Drugs used in the treatment of IBD can also cause these adverse effects and even lead to DILI. In this review, the various classes of drugs used in the treatment of IBD were taken into consideration and the various adverse effects on the liver were illustrated. In particular, a major role has emerged regarding hepatotoxicity of immunosuppressants. Biological drugs, however, seem to be responsible for these complications to a much lesser extent.

Vertical-axis wind turbines (VAWTs) are receiving more and more attention as they involve simple design, cope better with turbulence and are insensitive to wind direction which has a huge impact on the cost since the yaw mechanism is not needed. However, VAWTs still suffer from low conversion efficiency. As a results tremendous efforts are exerted to improve its efficiency which mainly focus on two methods regardless of whether the study is a CFD simulation or a field test or lab test experiment. An active approach which involves the modification of the rotor itself such as the blade design, angle, trailing and leading edges, inner blades, chord thickness, contra-rotating rotor, etc. While the second approach involves passive techniques where the flow is directed to optimally face the downwind rotor by mounting a guiding vane such as a diffuser or other shapes at the upwind position of the rotor. Among all techniques undertaken, the CRWT rotor technique seems to be the most effective with an output even comparable to that of Horizontal Axis Wind Turbines (HAWT), while the Savonius rotor received more attention compared to other designs of VAWTs. Apart from technological issues, it was also suggested that geographical issues such as proper site siting of the wind turbine rotor at a particular location where a uniform flow could be guaranteed is of paramount importance to ensure an effective conversion capacity of wind turbines.

Mechanical ventilation (MV), used in patients with acute lung injury (ALI), induces diaphragmatic myofiber atrophy and contractile inactivity, termed ventilator-induced diaphragm dysfunction. Phosphoinositide 3-kinase- (PI3K-) is crucial in modulating fibrogenesis during the reparative phase of ALI; however, the mechanisms regulating the interactions among MV, myofiber fibrosis, and PI3K- remain unclear. We hypothesized MV with or without bleomycin treatment would increase diaphragm muscle fibrosis through the PI3K- pathway. Five days after receiving a single bolus of 0.075 units bleomycin intratracheally, C57BL/6 mice were exposed to 6 or 10 mL/kg MV for 8 h after receiving 5 mg/kg of AS605240 intraperitoneally. In wild-type mice, bleomycin exposure followed by MV 10 mL/kg prompted significant increases in disruptions of diaphragmatic myofibrillar organization, transforming growth factor-1, oxidative loads, Masson’s trichrome staining, extracellular collagen levels, positive staining of -smooth muscle actin, PI3K- expression, and myonuclear apoptosis (P &lt; 0.05). Decreased diaphragm contractility and peroxisome proliferator activated receptor- coactivator-1 levels were also observed (P &lt; 0.05). MV-augmented bleomycin-induced diaphragm fibrosis and myonuclear apoptosis were attenuated in PI3K-γ-deficient mice and through AS605240-induced inhibition of PI3K- activity (P &lt; 0.05). MV-augmented diaphragm fibrosis after bleomycin-induced ALI is partially mediated through PI3K-γ. Therapy targeting PI3K-γ may ameliorate MV-associated diaphragm fibrosis.

Typhoons bring great damages to transmission line systems located in coastal areas. Strong wind and extreme precipitation are the main sources of damaging effects. Transmission lines suffered from wind-driven rain exhibit more susceptibility to damage due to the coupled effect of wind and rain water. This paper presents an integrated numerical simulation framework based on mesoscale WRF model, multiphase CFD model and FEM model to analyze the motions of a transmission line subjected to coupled wind and rain loads during typhoon events. A full-scale transmission line in Zhoushan island is employed to demonstrate the effectiveness of the proposed framework by simulating typhoon evolution in terms of wind fields and rainfall, solving the coupled wind and rain fields around the conductor and predicting the dynamic responses of the transmission line during Super Typhoon Lekima (2019). The results show that the horizontal displacements of the transmission line under the joint actions of wind and rain increases approximately 17%~18% compared to those of wind loads only. It is important to consider the coupled effects of wind-driven rain on conductors in the design of transmission lines under typhoon conditions.

Ensuring the accuracy of wind power prediction is paramount for the reliable and stable operation of power systems. This study introduces a novel approach aimed at enhancing the precision of wind power prediction through the development of a multiscale hybrid model. This model integrates advanced methodologies including Improved Intrinsic Mode Function with Ensemble Empirical Mode Decomposition with Adaptive Noise (ICEEMDAN), Permutation Entropy(PE), Least Squares Support Vector Regression (LSSVR), Regularized Extreme Learning Machine(RELM), Multi-head Attention (MHA), and Bidirectional Gated Recurrent Unit (BiGRU). Firstly, the ICEEMDAN technique is employed to decompose the non-stationary raw wind power data into multiple relatively stable sub-modes, while concurrently utilizing PE to assess the complexity of each sub-mode. Secondly, the dataset is reconstituted into three distinct components: high-frequency, mid-frequency, and low-frequency, to alleviate data complexity. Following this, the LSSVR, RELM, and MHA-BiGRU models are individually applied to predict the high, mid,and low-frequency components, respectively. Thirdly, the parameters of the low-frequency prediction model are optimized utilizing the Dung Betele Optimizer(DBO) algorithm. Ultimately, the predicted results of each component are aggregated to derive the final prediction. Empirical findings illustrate the exceptional predictive performance of the multiscale hybrid model incorporating LSSVR, RELM,and MHA-BiGRU. In comparison to other benchmark models, the proposed model exhibits a reduction in Root Mean Square Error(RMSE) values of over 10%, conclusively affirming its superior predictive accuracy.

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&amp;M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

Estimating parameters for multiple datasets can be time consuming, especially when the number of datasets is large. One solution is to sample from multiple datasets simultaneously using Bayesian methods such as adaptive multiple importance sampling (AMIS). Here we use the AMIS approach to fit a von Misses distribution to multiple datasets for wind trajectories derived from a Lagrangian Particle Dispersion Model driven from a 3D meteorological data. The primary objective is to characterise the uncertainties in wind trajectories in a form that can be used as inputs for predictive models of wind-dispersed insect pests and pathogens of agricultural crops for use in evaluating risk and in planning mitigation actions. Our results show that AMIS can significantly improve the efficiency of parameter inference for multiple datasets.

The last 50 years witnessed the emergence of various so called “hyperpolarization technologies” that allow generating large magnetizations of spin ensembles. This Editorial Essay provides a brief overview of the use of these technologies in various fields, including medicine, chemistry, and quantum sensing. It is concluded that critical questions still need to be addressed to harness benefits of nuclear hyperpolarization in clinical medical imaging while interdisciplinary innovation can unlock potential of novel (yet unexplored) methods. My hope is that this Editorial Essay provides valuable insights into the current state and future directions of spin technologies.

Drugs are known to cause substantial liver injury, with hepatotoxicity ranging from asymptomatic increase of liver enzymes to hepatic failure. HIV/AIDS patients, with compromised immune systems, are especially vulnerable to opportunistic infections such as tuberculosis (TB). Patients with co-infection frequently get combined antiretroviral (ART) and antitubercular (ATD) regimens, which can cause hepatotoxicity. Hepatotoxicity has been linked to commonly administered antiretroviral drug regimens as well as first-line antitubercular agents such isoniazid, rifampin, and pyrazinamide, which are required for the treatment of both drug-sensitive and drug-resistant tuberculosis. As a result, there is an urgent need to investigate treatments based from traditional herbs known for their hepatoprotective abilities against ART and ATD-induced liver injury. Many researchers have investigated the effectiveness of medicinal plants in treating chemically caused hepatotoxicity. Medicinal plants are high in phytochemicals and secondary metabolites, both of which have a variety of medicinal benefits. Currently, there is a lack of specific therapeutic regimens to address this adverse effect, and management often relies on symptomatic treatment or therapy withdrawal. Traditional medicinal plants may have the potential to restore normal liver function, enzyme activity, and cellular structure in response to ART and ATD-induced hepatotoxicity. This review aims to examine the scientific evidence supporting the use of medicinal plants as hepatoprotective agents against liver damage induced by ART and ATDs.

The theory of heavy ion double charge exchange (DCE) reactions proceeding by effective rank–2 isotensor interactions is presented. Virtual pion–nucleon charge exchange interactions are investigated as the source for induced isotensor interactions, giving rise to the Majorana DCE (MDCE) reaction mechanism. MDCE is of a generic character, proceeding through pairs of complementary (π±,π∓) reactions in the projectile and target nucleus. The dynamics of the elementary processes is discussed where the excitation of pion–nucleon resonances are of central importance. Investigations of initial and final state ion–ion interactions show that these effects are acting as vertex renormalizations. In closure approximation, well justified by the finite pion mass, the second order transition matrix elements reduce to pion potentials and effective two–body isotensor DCE interactions, giving rise also to two–body correlations in either of the participating nuclei. Connections to neutrinoless Majorana double beta decay (MDBD) are elucidated at various levels of dynamics, from the underlying fundamental electro–weak and QCD scales to the physical scales of nuclear MDBD and MDCE physics. It is pointed out that heavy ion MDCE reactions may also proceed by competing electro–weak charge exchange processes, leading to lepton MDCE by electrons, positrons, and neutrinos.

Introduction the outbreak of the Israel-Gaza conflict, initiated by a major attack on the civilian population in Israel provided a tragic opportunity to study the community wide association between severe emotional stressors related to acts of war and the incidence and clinical characteristics of Takotsubo cardiomyopathy (TCM) in this scenario. Methods Eight consecutive cases of TCM diagnosed during the first 50 days of the Israel-Gaza conflict were retrospectively collected from two southern medical centers who provided care to most of the war victims throughout the period of monitoring. The medical records were thoroughly reviewed and analyzed. Results During the monitoring period, the incidence of TCM increased substantially compared to the control period. Eight patients were included in the analysis. All patients were female and 100% of patients presented within the first 3 weeks of conflict whereas after this initial phase, despite the continuing war, the incidence of TCM reverted to pre-conflict levels. Two patients (25%) were under 50 years of age. All patients had hazardous clinical characteristics including severe left ventricular (LV) dysfunction (≤35%) and prolonged QTc interval (>500 ms). Five patients (62.5%) experienced complications. Nevertheless, no in-hospital mortality was reported. Conclusions Repeated exposure to severe emotional stress, on both personal and national level, due to mass crisis such as war is associated with an increased incidence of TCM potentially with high-risk phenotype in comparison to TCM following other, less potent, psychological insults.

Wind turbines (WTs) are clean a renewable energy source that has been growing in popularity in recent years. Gearboxes are complex, expensive, and critical components of WT, which are subject to high maintenance costs and several stresses including high loads and harsh environments that can lead to failure with significant downtime and financial losses. This paper focuses on the development of a digital twin-based approach for the modelling and simulation of WT gearboxes with the aim to improve their design, diagnosis, operation, and maintenance by providing insights into their behavior under different operating conditions. Pow-erful commercial computer-aided design tools (CAD) and computer-aided engineering (CAE) software are embedded into a computationally efficient multi-objective optimization framework (modeFrontier) with the aim of maximizing the power density, compactness, performance, and reliability of the WT gearbox. This entails minimizing its weight, volume, and maximum stresses and strains achieved without compromising efficiency. The 3D CAD model of the WT gearbox is carried out using SolidWorks, the Finite Element Analysis (FEA) to obtain the stresses and strains fields are modelled using Ansys Workbench, while the multibody kinematic and dynamic system is analyzed using MSC Adams. The method has been successfully applied to different case studies to find the optimal design and analyze the performance of the WT gearboxes. Simulation results can be used to identify potential failure modes and optimize gearbox design to improve performance, extend service life and relia-bility, thereby ensuring proper operation over its lifetime and reducing maintenance costs.

The chemotactic cytokine fractalkine (FKN, chemokine CX3CL1) has unique properties resulting from the combination of chemoattractants and adhesion molecules. The soluble form (sFKN) has chemotactic properties and potently attracts T cells and monocytes. The membrane-bound form (mFKN) facilitates diapedesis and is responsible for cell-to-cell adhesion, especially by promoting the strong adhesion of leukocytes (monocytes) to activated endothelial cells with the subsequent formation of an extracellular matrix and angiogenesis. FKN signaling occurs via CX3CR1, which is the only known member of the CX3C chemokine receptor subfamily. Signaling within the FKN-CX3CR1 axis plays an important role in many processes related to inflammation and the immune response, which often occur simultaneously and overlap. FKN is strongly upregulated by hypoxia and/or inflammation-induced inflammatory cytokine secretion, and it may act locally as a key angiogenic factor in the highly hypoxic tumor microenvironment. The importance of the FKN/CX3CR1 signaling pathway in tumorigenesis and cancer metastasis results from its influence on cell adhesion, apoptosis and cell migration. This review presents the role of the FKN signaling pathway in the context of angiogenesis in inflammation and cancer. The mechanisms determining the pro- or anti-tumor effects are presented, which are the cause of the seemingly contradictory results that create confusion regarding the therapeutic goals.

This study assesses the performance of the Weather Research and Forecasting (WRF) model using a high-resolution spatial grid (1 km) with various combinations of physical parameterization packages to simulate a severe event in August 2021 in the southeastern Brazilian coast. After determining the optimal set of physical parameterizations for representing wind patterns during this event, a year-long evaluation was conducted, covering forecast horizons of 24, 48, and 72 hours. The simulation results were compared with observational wind data from four weather stations. The findings highlight variations in the efficacy of different physical parameterization sets, with certain sets encountering challenges in accurately depicting the peak of the severe event. The most favorable results were achieved using a combination of Tiedtke (cumulus), Thompson (microphysics), TKE (boundary layer), Monin-Obukhov (surface layer), Unified-NOAH (land surface), and RRTMG (shortwave and longwave radiation). Over the one-year forecasting period, the WRF model effectively represented the overall wind pattern, including forecasts up to three days in advance (72-hour forecast horizon). Generally, the statistical metrics indicate robust model performance, even for the 72-hour forecast horizon, with correlation coefficients consistently exceeding 0.60 at all analyzed points. While the model proficiently captured wind distribution, it tended to overestimate northeast wind speed and gust intensities. Notably, forecast accuracy decreased as stations approached the ocean, exemplified by the ATPM station.

To maintain an optimal body content of phosphorus throughout postnatal life, variable phosphate absorption from food must be finely matched with urinary excretion. This amazing feat is accomplished through synchronised phosphate transport by myriads of ciliated cells lining the renal proximal tubules. These respond in real time to changes in the phosphate and composition of the renal filtrate, and to hormonal instructions. How they do this has stimulated decades of research. New analytical techniques, coupled with incredible advances in computer technology, have opened new avenues for investigation at a sub-cellular level. There has been a surge of research into different aspects of the process. These have verified long held beliefs and are also dramatically extending our vision of the intense, integrated, intracellular activity which mediates phosphate absorption. Already, some have indicated new approaches for pharmacological intervention to regulate phosphate in common conditions, including chronic renal failure and osteoporosis, as well as rare inherited biochemical disorders. It is a rapidly evolving field. The aim here is to provide an overview of our current knowledge, to show where it is leading, and where there are uncertainties. Hopefully this will raise questions and stimulate new ideas for further research.

The objective of the this study was to reduce the benzo[a]pyrene-induced hepatotoxicity method in herbal medicine products and to give proof that neferine, daidzein, genistein possess antihepa-totoxic effects. B[a]P which classified as a group 1 carcinogen and metabolized to B[a]P-7,8-dihydrodiol-9,10-epoxide (BPDE) causes mutagenic DNA addition products. The reduc-tion of BPDE-DNA adduct formation by B[a]P-7,8-dihydrodiol-9,10-epoxide (BPDE) was derived by benzo[a]pyrene (B[a]P). In HepG2 cells, B[a]P exhibited toxicity and substance treatment of the cells with B[a]P with neferine in lotus and daidzein, genistein in soybean reduced the BPDE-DNA ad-ducts level. The level of B[a]P-metabolites in the substance treatment of the cells was presented that BPDE levels were reduced by neferine in lotus and daidzein, genisten in soybean. These results suggest that neferine in lotus and daidzein, genistein in soybean prevent B[a]P-induced hepato-toxicity for BPDE-DNA adduct formation.

Presently, Jordan confronts a double substantial challenge of enhancing energy security and mitigating greenhouse gas emissions. One of the most encouraging avenues to attain the objectives of sustainable development, energy security, and environmental conservation is to enhance the integration of renewable energy into the generation of electricity. In pursuit of this goal, the Jordanian government intends to expand investments in the green energy sector, with solar and wind energy poised to play a key role in satisfying energy demands and cultivating an environmental sustainability. This paper aims to examine the distinctive dynamics, challenges, obstacles, and potential solutions corresponding to the establishment of community solar and wind farms in Jordan suburban areas. It aims to highlight the opportunities and barriers influencing the track of sustainable energy adoption in the country. Through a comprehensive analysis of the Jordanian context, the goal is to extract insights that can guide policies and practices. Additionally, the findings may serve as a valuable benchmark for other regions confronting similar challenges on their pursuit for a sustainable energy future.

This study uses a wind turbine case study to showcase an architecture for implementing a distributed digital twin in which all important aspects of a predictive maintenance solution in a DT use a fog computing paradigm, and the typical predictive maintenance DT is improved to offer better asset utilization and management through real time condition monitoring, predictive analytics, and health management of selected components of Wind turbines in a wind farm.. Digital twin (DT) is a technology that sits at the intersection of Internet of Things, Cloud Computing and Software Engineering to provide a suitable tool for replicating physical objects in the digital space. This can facilitate the implementation of asset management in manufacturing systems through predictive maintenance solutions leveraged by Machine Learning (ML). With DTs, a solution architecture can easily use data and software to implement asset management solutions such as Condition Monitoring and Predictive Maintenance using acquired sensor data from physical objects and computing capabilities in the digital space. While DT offers a good solution, it is an emerging technology that could be improved with better standards, architectural framework, and implementation methodologies. Researchers in both academia and industry have showcased DT implementations with different levels of success. However, DTs remain limited in standards and architectures that offer efficient predictive maintenance solutions with real time sensor data, and intelligent DT capabilities. An appropriate feedback mechanism is also needed to improve asset management operations.

Luminescent carbon dots (CDs) were locally synthesized in the core of CYTOP fibers using IR femtosecond laser direct writing (FLDW), a one-step simple method serving as a post-treatment of the genuine fiber. This approach enables the creation of several types of modifications such as ellipsoid voids. The CDs and photoluminescence (PL) distribute at the periphery of the voids. The PL spectral properties were studied through Excitation Emission Matrix in the visible range and excitation/emission spectrum in UV/visible range. Our finding reveals the presence of at least 3 distinct luminescent species, facilitating a broad excitation range extending from UV to green, and light emission spanning from blue to red. The average laser power and dose influence the quantity and ratio of these luminescent CD species. Additionally, we measured the spatially resolved lifetime of the luminescence during and after the irradiation. We found longer lifetimes at the periphery of the laser-induced modified regions and shorter ones closer to the center, with a dominant lifetime ~ 2ns. Notably, unlike many other luminophores, these laser-induced CDs are insensitive to oxygen, enhancing their potential for display or data storage applications.

Soil-borne Trichoderma spp. have been extensively studied for their biocontrol activities against pathogens and growth promotion ability with plants. However, the beneficial effect of Trichoderma on inducing resistance against insect herbivores has been considered only recently. Among diverse Trichoderma species, consistent with previous reports, we showed that root colonization by T. virens triggered induced systemic resistance (ISR) to leaf-infecting fungal pathogens. Whether T. virens induces ISR to insect pests has not been tested before. In this study, we investigated whether T. virens affects jasmonic acid (JA) biosynthesis and defense against fall armyworm (FAW) and western corn rootworm (WCR). Unexpectedly, the results showed that T. virens colonization of maize seedlings grown in autoclaved soil suppressed wound-induced production of JA, resulting in reduced resistance to FAW. Similarly, the bacterial endophyte Pseudomonas chlororaphis 30-84 suppressed systemic resistance to FAW due to reduced JA. Further comparative analyses of the systemic effects of these endophytes when applied into sterile or non-sterile field soil showed that both T. virens and P. chlororaphis 30-84 triggered ISR against hemibiotrophic fungal pathogen Colletotrichum graminicola in both soil conditions, but only suppressed resistance to FAW in sterile soil. In contrast to the effect on FAW defense, T. virens colonization of maize roots suppressed WCR larvae survival and weight gain. This is the first report suggesting the potential role of T. virens as a biocontrol agent against WCR.

This work is aimed at investigating the capabilities and limits of the mid-fidelity numerical solver DUST for the evaluation of wind turbines aerodynamic performance. In particular, this study was conducted by analysing the benchmarks NREL- 5MW and Phase VI wind turbines, widely investigated in literature by from experimental and numerical activities. The work started by simulating simpler configuration of the NREL- 5MW turbine to progressively integrate complexities such as shaft tilt, cone effects and yawed inflow conditions, offering a detailed portrayal of their collective impact on turbine performance. A particular focus was then given to the evaluation of aerodynamic responses from the tower and nacelle, as well as aerodynamic behavior in yawed inflow condition, crucial for optimizing farm layouts. In the second phase, the work was focused on NREL Phase VI turbine due to the availability of experimental data on this benchmark case. Comparison of DUST simulations results with both experimental data and high-fidelity CFD tools shows the robustness and adaptability of this mid-fidelity solver for this applications, thus opening a new scenario for the use of such mid-fidelity tools for the preliminary design of novel wind turbines configurations or complex environments as wind farms, characterised by robust interactional aerodynamics.

Familial Mediterranean fever (FMF) is a systemic autoinflammatory disorder caused by inherited mutations in the MEFV (Mediterranean FeVer) gene located on chromosome 16 (16p13.3) and coding pyrin protein. Despite the existing data on MEFV mutations, the exact mechanism of their effect on the development of pathological processes leading to autoinflammation observed in FMF, remains unclear. Induced pluripotent stem cells (iPSCs) are considered an important tool for studying the molecular genetic mechanisms of various diseases due to their ability to differentiate into any cell type, including macrophages, which contribute to the development of FMF. In this study, we developed iPSCs of an Armenian patient with FMF having M694V, p.(Met694Val) (c.2080A&gt;G, rs61752717) pathogenic mutation in exon 10 of the MEFV gene. As a result of direct differentiation, macrophages expressing CD14 and CD45 surface markers were obtained. In addition, we found that the morphology of patient macrophages derived from iPSCs with MEFV mutation was significantly different from that of differentiated from iPSCs of a healthy donor carrying wild-type MEFV gene.

Excess consumption of a high-fat diet has been identified as one of the contributing factors for obesity. Women are at higher risk for adult obesity than men, predisposing them to a different set of detrimental disease conditions. Furthermore, aging studies show that physiological decline also has a serious impact on changes in the endocrine properties of white adipose tissue. Howev-er, there is still relatively little known about the factors associated with obesity and aging and their compounding impact on women’s health. To investigate adipocytokine secretion profile changes, female C3H/HeJ mice were induced to obesity through long-term consumption of a high-fat diet. Weight gain measurements and Echo MRI analysis of fat composition showed in-creases were a due solely to the high fat content in the diet. Adipocytokine secretions were ana-lyzed in media conditioned from harvested visceral fat tissue that was organ cultured ex-vivo. Adipocytokine analysis across diets and age showed significant increases in Adiponectin and Leptin secretion in high-fat diets, accelerated increases in Resistin secretion with high-fat diets. Aging induced increased secretion of Lipcalin-2, Pentraxin-3 and Serpin E1, MCP-1 and ICAM-1, regardless of diet. Furthermore, comparisons of organoid cultured protein secretions and flash-frozen tissue samples differed greatly, suggesting the WAT organoid cultures may yield information more reflective of in situ conditions. Taken together, our results show that diet and aging significantly impact secretions from adipose tissue, that may contribute to women’s health issues.

In this paper, four probability functions are compared with the purpose of establishing a methodology to improve the accuracy of the estimated wind energy in a desert city in northwestern Mexico. For the statistical modeling, 3 time series of wind speed data were used, corresponding to the years 2017, 2018, and 2019, recorded with a sonic anemometer at a sampling frequency of 10 Hz. From these, the analysis is performed with different stationarity periods (5, 30, 60, and 600 seconds). The estimation of the parameters characterizing the probability density functions was performed using different methods; the statistical models were evaluated by the coefficient of determination and the Nash-Sutcliffe efficiency coefficient, while their accuracy by the measured quadratic error, the mean square error, the mean absolute error, and the mean absolute percentage error. It was found that Weibull with the energy pattern factor method and Gamma using the method of moments were the probability density functions that best describe the statistical behavior of the wind speed and, therefore, better estimate the energy generated, so it is concluded that the proposed methodology will allow having greater confidence, both in the estimation of the wind speed and in the small wind energy available for its use.

This paper delves into the application of digital twin monitoring techniques for enhancing offshore floating wind turbine performance, with a detailed case study. We explore the practical implementation of digital twins and their efficacy in optimizing operations and predictive maintenance. Our findings emphasize digital twins' potential as a valuable tool for renewable energy, driving efficiency and sustainability in offshore floating wind installations.

Inflammation is a cause of number of disorders. Many anti-inflammatory drugs are available to cure and prevent inflammation and its related disorders. Some of the drugs are from plant and animal origin. Among animals snake venom is also utilized as treatment option of certain disorders. In the current study the venom of N. oxiana from Northern areas of Pakistan is assayed to determine its anti-inflammatory activity. The Naja oxiana is also called central Asian cobra is endemic to Central Asia. Naja oxiana belong to family Elapidae and it is highly venomous snake. The venom has many enzymatic proteins as well as nonenzymatic proteins that is neurotoxins. The venom is lethal having very high mortality rate and the death may occur due to respiratory failure in 45 minutes to 24 hrs depending upon the nature and amount of venom. As the venom is highly toxic so initially after venom milking its protein estimation was done and toxicity profile and LD50 was determined to find out its therapeutic dose at which anti-inflammatory activity was observed. The toxicity and anti-inflammatory activity was determined on mice model. Inflammation was induced by carrageenan induced peritonitis method. The inflammatory markers ROS, TNF-α and IL-β were determined by ELIZA in peritoneal fluid. The LD50 of crude venom, fraction 1 and fraction 2 was found as 34 µg/kg, 7.4 µg/kg and 416 µg/kg respectively. Anti-inflammatory activity crude venom, fraction 1 and fraction 2 was found at dose 19 µg/kg, 1.8 µg/kg and 267 µg/kg respectively. The levels of inflammatory markers reduced after therapeutic dose administration of venom and its fractions that indicates that it can be utilized as anti-inflammatory agent and so can be effective in various disorders.

In this study, we define screening maps for Italy that classify sites based on their potential for triggering landslides. To this end, we analyze seismic hazard maps and hazard disaggregation results on a national scale considering four spectral periods (0.01s, 0.2s, 0.5s, and 1.0s) and three return periods (475, 975, and 2475 years). First, joint distributions of magnitude (M) and distance (R) from hazard disaggregation are analyzed by means of an innovative approach based on image processing techniques to find all modal scenarios contributing to the hazard. In order to obtain the M-R scenarios controlling the triggering of earthquake-induced landslides at any computation node, mean and modal M-R pairs are compared to empirical curves defining the M-R bounds associated with landslide triggering. Three types of landslides are considered (i.e., disrupted slides and falls, coherent slides, and lateral spreads and flows). As a result, screening maps for all of Italy showing the potential for triggering landslides based on the level of seismic hazard are obtained. The maps and the related data are freely accessible at the following web address: https://distav.unige.it/rsni/slideq.php.

The dust originating from the extinct lake of the Aral Sea poses a considerable threat to the sur-rounding communities and ecosystems. The accurate location of these wind erosion areas is an essential prerequisite for controlling sand and dust activity. However, few relevant indicators re-ported in the current study can accurately describe and measure wind erosion intensity. A novel wind erosion intensity (WEI) of a resolution unit was defined in this paper based on the deformation due to the wind erosion in this resolution unit. We also derived the relationship between WEI and soil InSAR temporal decorrelation (ITD). The ITD is usually caused by the surface change over time, which is very suitable for describing wind erosion. However, within one resolution unit, the ITD signal usually includes soil and vegetation contributions, and few studies are referred to this. Therefore, we proposed an ITD decomposition model (ITDDM) to decompose the ITD signal of a resolution unit. The least-squares method (LSM) based on singular value decomposition (SVD) is used to estimate the ITD of soil (SITD) within a resolution unit. We verified the results qualitatively by the landscape photos, which can reflect the actual conditions of the soil. At last, the WEI of the Aral Sea from June 23, 2020, to July 05, 2020, was mapped. The results confirmed that (1) Based on the ITDDM model, the SITD can be accurately estimated by the LSM method, (2) the Aral Sea is experiencing severe wind erosion, and (3) The middle, northeast, and southeast bare areas of the South Aral Sea are where salt dust storms may occur.

This paper presents a comprehensive analysis of the SEIRS COVID-19 pandemic model with saturated incidence rate. By modifying the existing model and proposing a new simplified version, we investigate the dynamics of disease transmission, including the impact of saturation terms on disease spread. Through stability analysis at disease-free and endemic equilibria, we aim to enhance understanding of the spread of COVID-19 and inform effective control strategies. Drawing on mathematical models and epidemiological insights, this study contributes to the ongoing efforts to combat the global pandemic.

In China's mountainous coastal terrain, the storm badly damaged low-rise buildings. At present, it is not clear how the relative position of buildings and mountains affects the surface of a low-rise building’s fluctuating coefficient. The study compared these results with the wind pressure distribution without the surrounding environment. The primary objective of this study is to examine the fluctuating coefficient variation rule based on the spacing between hillsides and buildings under 0° wind angle. Additionally, the study analyzes the fluctuating wind pressure coefficient across wind angles between 0°~90°. The distribution of wind pressure in different common hillside landforms was examined through a wind tunnel experiment, which also compared with the distribution in an open environment. The study examined the fluctuating coefficient as the distance between the building and the hillside changed, specifically for wind blowing at a 0° angle. Next, an analysis is conducted on the changing pattern of the fluctuating coefficient for low-rise buildings ranging from a wind angle of 0° to 90°. Simultaneously, the investigation examined the power spectrum and wind pressure’s probability distribution, while considering the proximity of the building to an adjacent hill. The findings indicated that the changing wind pressure factor on the surface of the structure differed based on the relative location of the hillside and the building. The roof's wind pressure coefficient fluctuated and gradually increased until it reached its peak, unaffected by the surroundings. The low-frequency energy decreased in windward eaves, while the high-frequency energy progressively rose as the distance between the hillside and the building increased. The wind pressure on the leeward side exhibited Gaussian characteristics in its probability distribution.

The aim of the present work is to explore a different non-traditional approach to higher dimensional spacetime which differs from the usual approaches such as large extra space dimensions, warped extra space dimensions and multiple extra time dimensions. This approach will be referred to as "Dynamic" higher dimensional spacetime. By this term will be introduced a new kind of higher dimensional spacetime (more than the usual 3+1 dimensions), which behaves dynamically in the sense that time is not a fixed dimension but is the extra plus one dimension to the spatial dimensions of the phenomenon we are studying. For a higher dimensional phenomenon, the lower dimensional time will behave as space and the new time will be a plus one dimension, meaning if we study a 3-dimensional phenomenon then time is the usual 4th dimension but if we are studying a 4-dimensional phenomenon then its time will be an extra 5th dimension and for this phenomenon the 4th dimension will behave as space. All spatial dimensions are indistinguishable from each other and behave in the exact same way, which means that the important parameter is not the dimension we are studying (for example the 4th or the 5th) but the number of dimensions in which a phenomenon can interact and how higher dimensional phenomena interact with lower ones. This non-traditional approach to higher dimensional spacetime may appear confusing at first but will become clearer in the rest of the paper. For this reason, we will first associate the time dimension with propagation relative to space dimensions and change orthogonal to them in order to give the reader a better intuition. Following that, we will describe how higher - dimensional phenomena would appear to us, the 3 - dimensional observer and try to set some guidelines on how we should mathematically model higher - dimensional phenomena in order for us to make accurate predictions of their behaviour. Then we will express the general framework of a "Dynamic" higher - dimensional spacetime and turn our gaze to 4+1 – dimensional phenomena. We will explore how a mass term arises for 4 – dimensional waves by generalizing the frequency – speed – wavelength relation of 3D waves and give a basic description on a possible way to describe a 4+1 – dimensional disturbance in a scalar Energy Field in order to make accurate predictions on our 3+1 dimensional plane. In this framework we will derive the Klein – Gordon equation by generalizing the wave equation and ignoring all lower than 4+1 - dimensional disturbances and compere our mass term findings with the Klein – Gordon equation mass term and with results from gravity – induced quantum interference experiments. Lastly, we will describe how a "Dynamic" 5 - dimensional spacetime would appear in a 3D observer and examine whether our findings are compatible with quantum mechanics and the special theory of relativity.

Wind turbines are a solution for sustainable energy, significantly reducing carbon emissions and fostering a circular economy for more cost-effective and cleaner power generation, in line with worldwide environmental aspirations. In this context, this research aims to explore a novel Two-Stage Twisted Blade micro-Vertical Axis Wind Turbine ($\mu$-VAWT) alternative inspired by the Savonius Rotor (SR). This investigation utilizes the $\kappa-\omega$ SST turbulence model to explore the power coefficient ($C_P$) and torque coefficient ($C_T$), finding $C_P$ values ranging from 0.02 to 0.04 across the turbine by altering the free stream velocity ($V$). $C_T$ analysis further delves into four specific sections, highlighting areas of particular interest. These results are validated by examining velocity contours, pressure contours, and streamlines in four horizontal sections, demonstrating that the proposed turbine model exhibits minimal torque fluctuation. Moreover, the analysis of vertical wind streamlines illustrates very low interference with various wind turbine proposals, underscoring the turbine's efficiency and potential for integration into diverse wind energy projects.

The paper presents modelling of relationships between wind velocity distributions observed in Poland and technical requirements for wind power stations design. The wind velocities distributions for various locations in Poland are determined, and expressed in Weibull distribution parameters. Theoretical computations concerning the dependence of wind power station as function of wind speed and aire physical properties are presented. Conclusions important for design of power stations fitted to atmospheric conditions in Poland are given. Wind power plants have been an important source of electricity generation for many years.Wind power modelling with the use of wind speed is used to improve the accuracy of forecasts and analyses of the power production of wind farms.

In the context of carbon neutrality and carbon peaking, in order to achieve low carbon emissions and promote the efficient utilization of wind energy, hydrogen energy as an important energy carrier is proposed to mix hydrogen and natural gas to form hydrogen enriched compressed natu-ral gas (HCNG). It is also injected into the natural gas pipeline network to realize the transmission and utilization of hydrogen energy. At the same time, the participation of demand response is considered, the load peak and trough period is adjusted, and large-scale consumption of renewa-ble energy and the reduction of carbon emissions are realized. First of all, a fine model of hydro-gen production and hydrogen use equipment is established to analyze the impact of adding hy-drogen mixing on the economy and low-carbon of the system. With green certificates and demand response, the utilization rate of hydrogen energy is improved to further explore the energy utiliza-tion rate and emission reduction capacity of the system. Secondly, on the basis of modeling, the optimal scheduling strategy is proposed with the sum of energy purchase cost, equipment opera-tion cost, carbon emission cost, wind curtailment cost and green certificate income as the lowest objective function. Considering the constraints such as hydrogen blending ratio and flexible load ratio of the pipeline network, a low-carbon economic scheduling model of hydrogen mixed natu-ral gas was established. The model was linearized and solved by using MATLAB and CPLEX solver. By comparing different scenarios, the superiority of the model and the effectiveness of the strategy are verified.

Among the many Lysosomal Storage Disorders (LSDs) that would benefit from the establish-ment of novel cell models, either patient-derived or genetically engineered, is Mucopolysaccha-ridosis type II (MPS II). In fact, even though a specific therapeutic approach does exist for this disorder (Enzyme Replacement Therapy, ERT, with recombinant human IDS) and haematopoiet-ic stem cell transplantation (HSCT) may also hold promise whenever the disorder is diagnosed soon enough, both approaches have their own drawbacks. Here we present our results on the establishment and characterization of two MPS II pa-tient-derived stem cell line(s) from deciduous baby teeth. To the best of our knowledge, this is the first time a stem cell population is isolated from LSD patient samples obtained from the oral cavity. Taking into account our results on the molecular and biochemical characterization of those cells and our first insights on their subcellular MPS phenotype, we consider these cells will be a valuable tool for both pathophysiological assessments and drugs screenings. Ultimately, we believe patient-derived dental pulp stem cells (DPSC) may represent a feasible alternative to induced pluripotent stem cells (iPSC) in many labs with standard cell culture con-ditions and limited (human and economic) resources.

Familial Alzheimer’s disease (FAD) can be caused by mutations in PSEN1 that encodes presenilin-1, a component of the gamma-secretase complex that cleaves amyloid precursor protein. Alterations in calcium (Ca2+) homeostasis and glutamate signaling are implicated in the pathogenesis of FAD, however it has been difficult to assess in humans whether or not these phenotypes are the result of amyloid or tau pathology. This study aimed to assess early calcium and glutamate phenotypes of FAD by measuring the Ca2+ response of induced pluripotent stem cell (iPSC)-derived neurons bearing PSEN1 mutations to glutamate and the ionotropic glutamate receptor agonists NMDA, AMPA and kainate compared to isogenic control and healthy lines. The data shows that in early neurons, even in the absence of amyloid and tau phenotypes, FAD neurons exhibit increased Ca2+ responses to glutamate and AMPA, but not NMDA or kainate. Together this suggests that PSEN1 mutations alter Ca2+ and glutamate signaling as an early phenotype of FAD.

Space exploration is an arduous journey, with future explorations extending in duration, increasing the risk for common space-related health issues such as bone density loss due to microgravity, impaired gut microbiota, cardiovascular ailments, and exposure to cosmic radiation. These ailments can be addressed using medicinal plants. Enhancing their efficacy entails employing gene editing to target specific secondary metabolite pathways associated with therapeutic properties. Moreover, gene editing can combine multiple medicinal properties from various plants, culminating in a singular 'superplant' with enhanced therapeutic benefits. This review discusses the current usage of medicinal plants in promoting human health during space travel, the application of gene editing technology in modifying medicinal plants and presents a vision for the utilization of gene-edited medicinal plants in space to mitigate the risk of various space-related health issues.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

Secondary movement disorders (SMDs) represent a heterogeneous group of neurological conditions characterized by abnormal, involuntary movements resulting from various underlying causes. This comprehensive review aims to thoroughly understand SMDs, including their epidemiology, pathophysiology, clinical manifestations, diagnostic approach, and management strategies. SMDs encompass a spectrum of movement abnormalities, including dystonia, chorea, athetosis, myoclonus, tics, and tremors. They can arise from a multitude of etiologies, such as drug-induced effects, post-infectious processes, metabolic disturbances, and structural brain lesions. The epidemiology of SMDs varies depending on the underlying cause, with some conditions being more prevalent in specific populations or age groups. Understanding the pathophysiology of SMDs is crucial for accurate diagnosis and targeted management. Diagnosing SMDs requires a comprehensive approach, including a detailed history, physical examination, laboratory investigations, neuroimaging studies, and sometimes electrophysiological studies. Management of SMDs is multifaceted and may involve pharmacological, non-pharmacological, and surgical interventions. Individualized treatment plans are essential, considering the underlying cause, severity of symptoms, and patient preferences. Emerging concepts in the field of SMDs include advancements in genetic research, identification of biomarkers, and development of novel therapeutic approaches. There is a growing focus on patient-centered care and improving the quality of life for individuals with SMDs. In conclusion, SMDs pose diagnostic and therapeutic challenges, requiring a multidisciplinary approach for optimal management. Continued research and collaboration are essential for advancing our understanding and treatment of these complex disorders.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

Introduction: Substance-induced psychotic disorder (SIPD) is a mental health condition linked to the use of a psychotropic substance whose pathogenesis has not been totally clarified. The present retrospective observational study has the objective to identify differences in clinical features and peripheral biomarkers in SIPD patients according to the main substance of abuse.Methods: A total sample of 218 patients was divided in 3 groups according to the type of consumed substance: alcohol, cannabis and psychostimulants. The 3 groups were compared for continuous variables by one-way analyses of variance (ANOVAs) and for qualitative variables by χ² tests. After removing alcohol-induced psychotic disorder group, the same analyses were repeated. Statistically significant variables from these latter analyses were included in a binary logistic regression model to confirm their reliability as predictors for cannabis- or psychostimulants-induced psychotic disorders. Results: Psychotic cannabis abusers were younger (p<0.01) and had an earlier age at onset (p<0.01). On the contrary, alcohol consumers resulted to have a longer duration of illness (p<0.01), more previous hospitalizations (p=0.04), more frequent medical comorbidity (p<0.01), higher mean Modified Sad Person Scale scores (p<0.01). Finally, psychostimulant abusers had more frequently a lifetime history of poly-substance use disorders (p<0.01). Binary logistic regression revealed that higher mean Brief Psychiatric Rating Scale scores (p<0.01) higher sodium (p=0.012) and haemoglobin(p=0.040) plasma levels were predictors of cannabis misuse in SIPD patients.Conclusions: Different clinical factors and biochemical parameters con be associated to SIPD according to the main substance of abuse, thus requiring a specific management by clinicians.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Within the spectra of lanthanide atoms quite often overlapping spectral lines (blends) are observed. On the example of complicated blend situations within Pr I and La I it is shown that in such cases a combination of optogalvanic and laser-induced fluorescence detection is necessary to find all transitions contributing to the observed spectral signature.

This paper performs a comprehensive analysis of the wind energy potential of onshore regions in Greece with emphasis on quantifying the volume risk and the spatial covariance structure. Optimization techniques are employed to derive efficient wind capacity allocation plans (also known as generation portfolios) incorporating different yield aspirations. The generation profile of minimum variance and other optimal portfolios along the efficient frontier are subject to rigorous evaluation using a fusion of descriptive and statistical methods. In particular, principal component analysis is employed to estimate factor models and investigate the spatiotemporal properties of wind power generation, providing valuable insights into the persistence of volume risk. The overarching goal of the study is to employ a set of statistical and mathematical programming tools guiding investors, aggregators and policy makers in their selection of wind energy generating assets. The findings of this research challenge the effectiveness of current policies and industry practices, offering a new perspective on wind energy harvesting with a focus on the management of volume risk.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

Hiccups can significantly reduce the quality of life of patients and can occur as a drug side effect. Previous report using the Drug Adverse Event Database revealed sex-specific differences in the incidence of drug-induced hiccups. However, the pathogenesis of drug-induced hiccups remains unknown, and there is limited evidence on its treatment or prevention. This study examined molecular initiating events (MIEs), which are the starting point of adverse events, to investigate the drug-induced pathways of hiccups. We extracted drugs suspected to cause hiccups using FDA Adverse Event Reporting System, a large database on adverse drug reactions. Information on drugs suspected to be associated with hiccups were extracted from the overall population and sex-specific subgroups divided. In each data table, the predicted activity values of nuclear receptors (NRs) and stress response pathways (SPs) for each drug were calculated using the toxicity predictor, a machine-learning model. Univariate analysis extracted NRs and SPs associated with hiccups, and a multivariate analysis was performed to evaluate independent factors. Transforming growth factor-beta and antioxidant response element were considered an independent factor for hiccups in the male and female subgroups, respectively. This report first examined one of the mechanisms of drug-induced hiccups and identified MIEs associated with drug-induced hiccups.

Contrast-Induced Acute Kidney Injury (CI-AKI) remains a frequent iatrogenic condition since radiological procedures using intra-vascular iodinated contrast media (CM) are being widely administered for diagnostic and therapeutic purposes. Despite the improvement of the medical healthcare system worldwide, CI-AKI is still associated with direct short-term and indirect long-term outcomes including increased morbidity and mortality, specially, in patients under-lying pre-existing renal function impairment, cardiovascular disease or diabetes that could rap-idly progress into Chronic Kidney Disease. Although the RIFLE (Risk, Injury, Failure, Loss, End-Stage Kidney Disease), AKIN (Acute Kidney Injury Network) and KDIGO (Kidney Disease Improving Global Outcomes) clinical criteria and recommendation guidelines are based on tra-ditional “gold standard” biomarkers known as serum creatinine, glomerular filtration rate and urinary output, new reliable serum and urinary biomarkers are still needed for an effective uni-fied diagnostic strategy for AKI. Starting from previous and recent publications on the benefits and limitations of validated biomarkers responding to kidney injury, glomerular filtration and inflammation among others, this review unravels the role of new emerging biomarkers used alone or in combination, as reliable tools for early diagnosis and prognosis of CI-AKI, taking into account patients and procedures-risk factors towards a new clinical perspective.

This study concerns calculation and comparison of Fe, Co, Ni and Cu deposition rates in tungsten codeposition process based on electrodeposition of numerous tungsten alloys. 8 different tungsten alloys containing from 2 to 5 metals were electrodeposited in constant conditions in order to compare exact reduction rates. Calculated rates enabled control of the alloy composition precise enough to obtain a high-entropy WFeCoNiCu alloy with well-balanced composition. Introduction of copper to form the quinternary alloy was found to catalyze the whole process, increasing deposition rates of all components of the high-entropy alloy.

In the full load operating range, wind turbines typically use pitch control to maintain rotor speed and output power at their rated values to guarantee the whole system’s safety. Blade pitch actuators are subject to physical limitations and safety requirements, which imposes strict constraints on pitch angle’s amplitude and rate of change. These constraints will bring windup problem to the integral part of the pitch controller. It leads to deterioration of the pitch control system’s performance or even the instability problem, especially for large-scale turbines operating in extreme uncertain wind conditions or suffering from cyber attacks. This paper designs an anti-windup robust pitch angle control strategy to deal with pitch rate constraint issue to enhance the security of control system. First, to facilitate controller design, a filtered tracking error technique is employed to transform the nonaffine form into an affine one. Subsequently, a feedback robust controller based on UDE is developed to handle the model’s uncertainty and external disturbances. To address the issue of integral saturation in the pitch system and guarantee its safety, an elliptical bounded constraint is integrated into the designed UDE strategy. This bounded UDE controller can improve the stability of power generation quality, reduces the mechanical loads on components and enhance the whole system’s safety. Finally, the effectiveness of the proposed scheme is verified on the Wind Turbine Blockset platform in Matlab/Simulink. It can achieve better performance than the traditional method.

Peptidylarginine deiminases (PADs) have an important role in the pathogenesis of generating citrullinated proteins which is one type of protein posttranslation modifications (PTMs). Additionally, peptidylarginine deiminases 4 (PAD4) is a component of neutrophil extracellular traps (NET) that leads to autoimmune disease during NETosis. Our aim was to check the PAD4 enzyme expression at level of gene and protein expression in streptozotocin (STZ) induced diabetic rat pancreas and checking the link between PAD4 and inflammatory cytokines. Wistar rats were divided into two groups: control group and diabetic STZ group. STZ was administered by intraperitoneally (60 mg/kg/ body weight). Rats were caged for six weeks and then terminated. Pancreatic tissue was harvested for measurement of PAD4 protein expression, PAD4 mRNA, citrulli-nated histone-3 protein (CITH3), cytokines and Ca2+ content. All measurements in diabetic rats were significantly in-creased compared to non-diabetic rats (p

Angiotensin-converting enzyme (ACE) inhibitors are used primarily in the treatment of hypertension, heart failure, and in the acute phase of myocardial infarction. Lisinopril [N2-[(1S)-1-car-boxy-3-phenylpropyl]-L-lysyl-L-proline], enalapril [(S)-1-[N-[1-(ethoxycarbonyl)-3-phenylpropyl]-L-alanyl]-L-proline] and ramipril [2-aza-bicyclo-[3.3.0]-octane-3-carboxylic acid] are all five-membered heterocycles and three of the most prevalent ACE inhibitors in clinical use worldwide. ACEi-induced angioedema (ACEi-AE) is clinically characterized by self-limited edema of the dermis and subcutaneous lipid tissue, localized on face skin, oral mucosa and tongue in most cases. However, severe episodes of intestinal AE misdiagnosed as acute appendicitis and laryngeal AE requiring incubation have been reported. The pathophysiology of ACEi induced-AE is attributed to the accumulation of bradykinin, which is a potent vasodilator with proinflammatory activity that is normally degraded by angiotensin-converting enzyme (ACE) and aminopeptidase P; however, a small proportion of treated patients is affected. Given that patients do not respond to anti-H1 antihistamines and steroids, the early clinical recognition and the ACEi discontinuation are the treatment of choice for the long term management of ACEi-AE.

: AliCPT-1 is the first Cosmic Microwave Background (CMB) experiment in China, dedicated to achieve accurate measurements of B-mode polarization. Situated in Ali of Tibet, China, this telescope is currently undergoing deployment and will operate in two frequency bands centered at 90 and 150 GHz. The Far-Field Flat Mirror（FFF）is a calibration device of AliCPT-1 telescope for far-field beam mapping. The design of FFF is optimized for easy assembly and adjustment. Meteorological station data reveals that the maximum wind speed near FFF is 17.5 m/s, while the maximum wind speed on the windward side is 8 m/s. The wind pressure on FFF was analysed using a maximum wind speed of 17.5m/s as the input condition, based on the fluid-structure coupling method in ANSYS. The results demonstrate that it is safe and reliable when withstanding combined gravity and wind pressure loads. The torque on the mount is within the motor rated torque. The flatness of the FFF reflective surface can be adjusted to an RMS value of 0.05 mm when taken into account the effect of gravity and assembly accuracy. The deformation caused by the maximum wind loads is approximately 0.0587 mm under the protection of wind-proof wall. The combined deformation is 0.077 mm in RMS value combining the two influences, which is less than 1/20 of wavelength. The FFF mirror assembly is stable and precisely for telescope calibration.

This article presents the suitability analysis of onshore wind farm sites using an AHP (Hierarchical Analysis Process) multi-criteria decision-making (MCDM) approach based on geographic information system modeling (GIS). This analysis is based on different technical aspects (wind speed, elevation, slope), economic (proximity to the electricity network, proximity to roads) and social (proximity to residential areas, population density). The introduction of the factor “population density” and the constraint “required area” rarely used in previous studies makes it possible to refine the results. The data is classified into several categories in a gradual manner, namely unsuitable (0); less suitable (1); suitable (2); highly suitable (3) and most suitable (4). The results of the study show us that the largest percentage relating to spatial coverage is observed in the “suitable” range with 50.89% and the corresponding TWPP (theoretical wind power potential) is 1377.926 GW; it is followed by “highly suitable” 5.67% and a TWPP of 153.652 GW; then “less suitable” with 1.04% and a TWPP of 28.163GW. No areas were identified in “most suitable” and finally the “unsuitable” range with 42.4%. The results show that the most favorable areas are located in the part of the far north of the country corresponding to the strong wind zone. The sensitivity analysis was carried out based on scenario tests (technical, economic and equal-weight) in order to give greater visibility of choice to the different stakeholders who would like to invest in onshore wind energy in Cameroon. This study is useful in more than one way because the results obtained can help investors, the government and other stakeholders to identify potential areas for the deployment of wind energy systems in Cameroon. Furthermore, a study of hybrid solar-wind systems could improve the efficiency of electricity parks in Cameroon.

Coastal dunes worldwide are increasingly under pressure from the adverse effects of human activities. Therefore, more and more restoration measures are being taken to create conditions that help disturbed coastal dune ecosystems regenerate or recover naturally. However, many projects lack (open-access) monitoring observations needed to signal whether further actions are needed, and hence to learn by doing. This submission presents an open access data set of 37 high-resolution digital elevation models and 24 orthomosaics collected before and after the excavation of five artificial foredune trough blowouts ("notches") in winter 2012/2013 in the Dutch Zuid-Kennemerland National Park, one of the largest coastal dune restoration projects in northwest Europe. These high-resolution data provide a valuable resource for improving understanding of the biogeomorphic processes that determine the evolution of restored dune systems, as well as developing guidelines to better design future restoration efforts with foredune notching.

Movement disorders can be associated with various drugs and systemic diseases, posing diagnostic challenges for clinicians. This review explores the spectrum of movement disorders associated with pharmacological agents and medical conditions. Drug-induced movement disorders encompass a broad range of conditions resulting from exposure to medications that affect several neurotransmitters. Neuroleptic medications can lead to tardive dyskinesia, characterized by involuntary, repetitive movements. Antipsychotics and antiemetics, including metoclopramide, may induce acute dystonic reactions. Other drugs, such as dopamine receptor-blocking agents, can contribute to drug-induced parkinsonism. Beyond medications, movement disorders can also arise secondary to systemic diseases. Metabolic disorders like Wilson's disease, characterized by copper accumulation, may manifest as chorea or dystonia. Inflammatory conditions such as rheumatoid arthritis and systemic lupus erythematosus can result in secondary movement disorders due to autoimmune-mediated processes affecting the central nervous system. Movement disorders linked to drugs or systemic diseases often necessitate a thorough clinical evaluation, including detailed medication histories and comprehensive systemic assessments. Neuroimaging, laboratory investigations, and, in some cases, cerebrospinal fluid analyses and electrodiagnostic studies help in establishing accurate diagnoses. Management involves addressing the underlying cause, modifying medications, and employing symptomatic treatments.

This paper discusses how mathematical models are used to predict environmental conditions. While these models are successful for larger scale phenomena, it becomes more complex for local weather or wave processes. Several approaches have been proposed to address this problem, including neural networks and statistical and mathematical models. The novelty in this approach is the use of statistical manifolds, which provide a more accurate way to estimate distances and cost functions. This work focuses on advancements in differential and information geometry for creating different types of models that can be used for environmental simulation and forecasting. These fields are vital for many institutes and centres worldwide, as they help solve challenges in areas such as meteorology, renewable energy, and aviation safety. Some potential IG applications to advance energy were given. Closing remarks with new open problems combined with the next research phase are provided.

To investigate the associated mechanisms concerning collagen and the expression of apoptosis-related proteins in porcine skin injuries induced by laser exposure, pig skin was treated with a 1064 nm laser. The healing process of the laser-treated areas, alterations in collagen structure, and changes in apoptosis were continuously observed and analyzed from 6 hours to 28 days post-irradiation. On the 28th day following exposure, wound contraction and recovery were notably sluggish in the medium-high dose groups, displaying more premature and delicate type III collagen within the newly regenerated tissues. The collagen density in these groups was roughly 37-58% of that in the normal group. Between days 14 and 28 after irradiation, there was a substantial rise in apoptotic cell count in the forming epidermis and granulation tissue of the medium-high dose group, in contrast to the normal group. Notably, the expression of proapoptotic proteins bax, caspase-3, and caspase-9 surged significantly 14 days after irradiation in the medium-high dose groups and persisted at elevated levels on the 28th day. During the later stage of wound healing, the augmented apoptotic cell population and insufficient collagen generation in the newborn skin tissue of the medium-high dose groups were closely associated with delayed wound recovery.

The exceptional performance of graphene has driven the advancement of its preparation technique and application. Laser-induced graphene (LIG), as a novel graphene preparation technique, has been applied in various fields. Graphene periodic structures created by LIG technique exhibit superhydrophobic characteristics and can be used for deicing and anti-icing applications, which are significantly influenced by the laser parameters. The laser surface treatment process was simulated by a finite element software analysis (COMSOL Multiphysics) to optimize the scanning parameter range, and the linear array surface structure were subsequently fabricated by the LIG technique. The generation of graphene was confirmed by Raman spectroscopy, and energy-dispersive X-ray spectroscopy. The periodic linear array structure were observed by Scanning electron microscopy (SEM) and confocal laser imaging (CLSM). In addition, CLSM testings, contact angle measurements, and delayed icing experiments were systematically performed to investigate the effect of scanning speed on surface hydrophobicity. The results show that the high quality and uniform graphene can be achieved using the laser scanning speed of 125 mm/s. The periodic linear array structures can obviously increase the contact angle and suppress delayed icing. Furthermore, these structures have the enhanced ability of the electric heating deicing, which can reach 100°C and 240°C within 15 s and within 60 s under the DC voltage power supply ranging from 3 to 7 V, respectively. These results indicate that the LIG technique can be developed to provide an efficient, economical, and convenient approach for preparing graphene and the hydrophobic surface array structure based on LIG has considerable potential for deicing and anti-icing applications.

The growth of the wind power sector has been marked by environmental, economic, and political drivers. Its starring role is also visible in the emergence of the so-called “green jobs”. Notwithstanding, its evolution ought not to compromise issues related to occupational risks. This exploratory study examines psychosocial risks in the operation and maintenance of onshore wind turbines in a leading Portuguese company. We conducted interviews with main stakeholders (Human Resources, OHS professionals, and team leaders); developed an “activity diary” for the operation and maintenance technicians to describe their activity and perceived impacts on health, complemented with collective interviews; and applied the Work and Health Survey. The results revealed particular risks and health impacts: working under adverse weather conditions; working at heights and in confined spaces; spending long work hours inside of the nacelles to achieve an optimum balance between favorable wind slots to intervene and avoiding additional trips up and down the wind turbines without lifts (70m-120m); and the feeling of early ageing. At a time when these workers are striving for recognition of their profession as a “rapid wear profession”, it is a key moment to discuss these results to guarantee sustainable conditions for future generations of workers.

For esophageal cancer patients treated with neoadjuvant chemoradiotherapy (nCRT), restaging using F-18-fluorodeoxyglucose (18F-FDG) positron emission tomography computed tomography (PET-CT) following nCRT can detect interval metastases, including liver metastases, in almost 10% of patients. However, in clinical practice, focal FDG liver uptake, unrelated to liver metastases, is observed after chemoradiotherapy. This radiation-induced liver injury (RILI) can potentially lead to overstaging. Liver radiation damage is also a concern during distal esophageal cancer radiotherapy due to proximity to the left liver lobe, typically included in the radiation field. Post-CRT, if FDG activity appears in the left or caudate liver lobes, thorough investigation is needed to confirm or rule out distant metastases. The increased FDG uptake in liver lobes post-CRT often presents a diagnostic dilemma. Distinguishing between radiation-induced liver disease and metastasis is vital for appropriate patient management, necessitating a combination of imaging techniques and an understanding of the factors influencing radiation response. Diagnosis involves identifying new foci of hepatic FDG avidity on PET/CT scans. Geographic regions of hypoattenuation on CT and well-demarcated regions with specific enhancement patterns on contrast-enhanced CT scan and MRI are characteristic of radiation-induced liver disease (RILD). Lack of mass effect on all three modalities (CT, MRI, PET) indicates RILD. Resolution of abnormalities on subsequent examinations also helps in diagnosing RILD. Moreover, it can also help to rule out occult metastases, thereby excluding those patients from further surgery who will not benefit from esophagectomy with curative intent.

SARS-CoV-2 virulence is known to increase with lowering of environmental temperature and solar ultraviolet radiation; therefore, we have focused our real-world nationwide study concerning with COVID-19 trends and dynamics on the coldest seasons of the year in Italy, the Western country hardest hit at the onset of the pandemic, comparing the autumn-winter of 2020 (before mass vaccination but when the emergency machinery was fully operative in terms of tracing and swabs) with the autumn-winter of 2021 (after mass vaccination), and analyzing the mortality burden by age groups and life stages in the years 2019 (pre-COVID-19), 2020 (before mass vaccination) and 2021 (after mass vaccination). Methods: During the state of national health emergency, the Civil Defense Department released the aggregate data coming from the Higher Institute of Health, the Ministry of Health, the Italian Regions, and the Independent Provinces, to inform the population (58.85 million people) about the pandemic situation, daily. Among these data there were the number of contagions, performed swabs, hospitalizations in Intensive Care Units (ICU), non-ICU patients, and deaths. By means of a team effort, we have collected and elaborated all these data, comparing the COVID-19 pandemic in Italy during the autumn-winter of 2020 with the autumn-winter of 2021. Moreover, we have extracted from the database of the National Institute of Statistics the total number of annual deaths in Italy during the years 2019, 2020 and 2021, comparing them to each other in order to evaluate the mortality burden attributable to COVID-19. Results: From the autumn-winter of 2020 to the autumn-winter of 2021, the contagions increased by ≈285%, however against a ≈290% increase in the performed swabs; therefore, the mean positivity rate passed from 8.74% before mass vaccination to 8.59% after mass vaccination. The unprecedent vaccination campaign allowed a ≈251% abatement in COVID-19 deaths, and a reduction of ≈224% and ≈228% in daily ICU and non-ICU hospitalizations due to COVID-19, respectively. Regarding COVID-19 deaths, in 2020 there was a mortality excess of ≈14.3% quantifiable in 105,900 more deaths compared to 2019, the pre-COVID-19 year; 103,183 out of 105,900 deaths occurred in older adults (≥60 years), which is equivalent to ≈97.4%, while in adults over 50, the segment of population just below older adults, in 2020 there were 2807 more deaths than in 2019. Surprisingly, from the analysis of our data, it is emerged that under the age of 40 in the years 2019, 2020 and 2021 there were 7103, 6808 and 7165 deaths, respectively. This means that in subjects under 40 during 2020 there were 295 fewer deaths than in 2019, while during 2021 there were 357 more deaths than in 2020, equivalent to ≈5.2% more. Conclusions: COVID-19 is a potential life-threatening disease mainly in older adults, as they are the most vulnerable due to inherent immunosenescence and inflammaging. Extensive vaccination in this segment of population with up-to-date vaccines is the means to reduce deaths, hospitalizations, and ICU pressure in the public interest. In the event of future threats, a new mass vaccination campaign must not be implemented without taking into account the individual age; it should primarily be aimed at people over 60 and at patients of any age with immune deficits, and secondly at people over 50. COVID-19 vaccination shows a favorable benefit-risk balance in older adults, while this balance falls under the age of 40; this younger segment of population should be therefore exempt from any mandatory vaccination.

The terrain of Changbai Mountain has great influence on the distribution of atmospheric flows and the occurrence and development of precipitation. This study quantitatively analyzes the regional characteristic of topographic perturbations and the relationship between terrain, wind and precipitation in Changbai Mountain region, by using a spectral analysis of the two-dimensional discrete cosine transform. Three domains with relatively heavy summer precipitation are selected as the study region. The results indicate that the overall terrain of Changbai Mountain region exhibits anisotropic characteristics. The terrain spectra of domain B are less than those of domain A and C across the whole wavelength (λ) bands, indicating that the large-scale topographic perturbations of domain B are relatively weak. The largest topographic spectral peak of domain C shows the most pronounced undulation of terrain among the three domains. The dominant wavelengths of terrain height variance for domain A and C, both close to the respective maximum wavelengths, indicate more prominent large-scale topographic perturbations. For domain A, the variation of the precipitation spectra is consistent with that of the wind spectra at the wavelength bands of λ < 390 km, showing a high correlation between wind field and the occurrence of rainfall. The inverse relationship at larger wavelengths indicates that multiple factors contribute to the occurrence of rainfall. For domain B, there is consistency in the fluctuations of terrain spectra, precipitation spectra, and wind spectra at the wavelength bands of λ < 278.3 km, implying that the smaller-scale terrain has an important effect on the occurrence of summer precipitation. For domain C, the variations of terrain spectra, precipitation spectra, and wind spectra are almost consistent across the whole wavelength bands, indicating that the large-scale terrain and minor terrain both play a crucial role in atmospheric uplift and the occurrence and development of summer rainfall.

The paper presents an implementation and numerical study of the nonlinear optimal-based vibration control solutions for the full-scale TLP – NREL 5MW wind turbine tower-nacelle model with an MR-damper-based 10 ton tuned vibration absorber (TVA) located at the nacelle, under excessive wave/wind polyperiodic excitations yielding continual transient vibration states. The MR damper operates simultaneously with an electromagnetic force actuator (forming a hybrid TVA), or independently (a semiactive TVA). The study includes both actuators’ nonlinearities and dynamics, whereby the former are embedded in the Hamilton-principle-based nonlinear control solutions. As a reference, the structure model with a passive TVA, with a modified ground-hook control law, and without any vibration reduction solutions is used. The TVA was tuned either to the NREL 5MW tower-nacelle 1st bending mode frequency (TVA-TN) or to the TLP surge frequency (TVA-TLP). The optimal control task, redeveloped here with regard to the TVA stroke amplitude minimisation, including the implementation of the protected structure’s acceleration (control case III / III-H) and relative displacement terms as well as nonzero velocity term in the quality index, is stated and solved, yielding optimal-based control propositions for both the MR damper current and the actuator force. On the basis of the obtained results, the TVA-TN solution is by far superior to the TVA-TLP one regarding the tower deflection amplitude / root-mean-square (RMS) and TVA stroke amplitude values. All the regarded TVA-TN solutions provide tower deflection safety factor of ca. 2, while a structure without any vibration reduction solutions or with a TVA tuned to the TLP surge frequency (especially passive and hybrid TVA-TLPs) are at risk of tower structural failure. The obtained TVA stroke amplitudes are reduced with regard to the previously developed approaches. Moreover, these reductions are obtained due to the sole control algorithm enhancement; thus, no additional resources are necessary, while this attainment is accompanied with a reduction in the MR damper force that is necessary for the TVA operation. The protected structure’s acceleration term utilisation produce the TVA stroke amplitude reduction more efficiently than the TVA relative displacement term usage, as in the previously developed approach (the latter being ineffective for the semiactive TVA implementation) which, in turn, efficiently reduces TVA stroke RMS values and the required mean actuator power for the hybrid TVA implementation. Concerning the limited TVA stroke, the most favourable vibration control solutions are the newly introduced semiactive control case III, providing favourable cumulative primary structure deflection indexes at the lowest obtained TVA travel distance, and possibly the hybrid control case III-H, providing even more favourable primary structure deflection qualities and reduced nacelle acceleration levels thanks to the utilisation of the force actuator of the relatively low power (ca. 6 kW); however, side effect of the latter is the increased TVA stroke amplitude as for all hybrid solutions tested (comparing to semiactive solutions). The analysed passive TVA systems along with the modified ground-hook hybrid TVA solution, utilising the assumed absorber mass, can hardly be implemented in the nacelle, especially along the demanding side-side direction, without enforcing end-stop collision bumpers, which result in the efficiency deterioration. The ground-hook control, well proven for the primary structure steady-state deflection minimisation, yielded unsatisfactory results, comparing to the newly implemented solutions. The results of the current study may be used during the design of the full-scale vibration reduction system for the real-world NREL 5MW-class floating, TLP-based, wind turbine structure.

Modern engineering faces challenges in ensuring technical standards for service, durability, and sustainability. Political, administrative, and budgetary factors, coupled with climate change, pose tasks to structural integrity, affecting industries and economies. Marine infrastructures represent a strategic asset of the country as it handles a large part of the economic exchanges. This article analyzes five essential factors that play a fundamental role in the performance analysis of coastal structures: Chloride-induced corrosion, degradation models, maintenance strategies, monitoring, and climate change. Starting with reinforcement corrosion, considered as the main cause of distress, particularly in coastal zones for the long-term behavior of structures. Additional pressure from the influences of climate change is becoming evident and extreme, leading to reduction in capacity. To guarantee the lifespan, degradation models contribute by estimating the long-term performance of the asset as a strategic piece to the development of effective maintenance solutions. Additionally, quantifying the condition of the structure from monitoring data, plays a crucial part that provides information on the current situation of the structure. Finally, this review summarizes the challenges associated with the maintenance of aging marine structures considering aspects such as corrosion, monitoring, and the future challenges this area will face due to climate change.

Previous studies have demonstrated that cold pools play a pivotal role in the initiation and organization of convection, yet their influence on the evolution of GFs remains inadequately understood. A destructive wind event associated with a rearward gust front (RGF, 8 grade gale appeared after passing GF) and a prior gust front (PGF, 10 grade gale appeared before passing GF) over the north coast of China on 10 June 2016 was analyzed. Using multiple observation data as well as the four-dimensional Variational Doppler Radar Data Assimilation System (VDRAS), we found that the intensity of the GFs increased with increasing cold pool strength, depth and propagation speed. Two schematic models were proposed to explain the discrepancy between GFs and associated cold pools. The depth and intensity of the cold pool in RGF are found to be relatively shallower and weaker, leading to a correspondingly reduced strength in both outflow and convergence. In contrast, the enhanced vertical shear and boundary northeaster inflow of PGF generate intensified and more organized downdrafts, resulting in a deeper cold pool, robust outflow, and convergence. These findings offer novel insights into the diversity of GFs and associated cold pools.

The ability to control the temperature distribution T(t,r) and the rate of temperature change Rt,r inside glasses is important for their microstructuring. The lattice temperature is considered at time t, exceeding the electron-phonon thermalization time, and at a distance r from the center of the model spherical heating zone. In order to describe thermal excitations, the heat capacity of glasses must be considered as a function of time due to its long-term relaxation. A method for analytical calculation of T(t,r) and R(t,r) for glasses with dynamic heat capacity cdyn(t) is proposed. It is shown that during laser microstructuring the local cooling rate -R(t,r) significantly depends on the time dispersion of cdyn(t). It has been established that at the periphery of the model heating zone of the laser beam focus, the local cooling rate can reach more than 1011 K/s. Strong cooling rate gradients were found at the periphery of the heating zone, affecting the microstructure of the material. This effect is significantly enhanced by the time dispersion of cdyn(t). The effect associated with this time dispersion is significant even well above the glass transition temperature Tg, since even short relaxation times of the dynamic heat capacity cdyn(t) are significant.

The emerging industry of offshore wind turbines mounted on floating bases has garnered significant attention from both academia and industry. The desire to understand the complex physics of these floating structures has led to the development of numerical and physical modelling techniques. While physical testing has traditionally been employed, there is a growing focus on cost-effective and accurate high-fidelity numerical modelling as a potential alternative or supplement. However, commonly used numerical engineering tools in the offshore industry are considered mid- to low-fidelity and may lack the desired precision for floating offshore wind turbines (FOWTs). Given the complexity of these simulation codes, it is crucial to validate their accuracy. To address this, the International Energy Agency (IEA) Wind Technology Collaboration Programme initiated various research endeavors, including the Offshore Code Comparison Collaboration (OC3), Offshore Code Comparison Collaboration Continuation (OC4), Offshore Code Comparison Collaboration Continuation with Correlation (OC5), and the recent Offshore Code Comparison Collaboration Continued with Correlation and Uncertainty (OC6) projects. This study offers a comprehensive survey of the simulation tools available for FOWTs which were part of OC projects, focusing particularly on horizontal axis wind turbines (HAWTs) and highlighting their capabilities and fundamental theories.

Circadian rhythm disruption is increasingly considered an environmental risk factor for the development and exacerbation of inflammatory bowel disease. We have reported in a previous study that nychthemeral dysregulation is associated with an increase in intestinal barrier permeability and inflammation in mice with dextran sulfate sodium (DSS)-induced colitis. To investigate the effect of circadian rhythm disruption on the composition and diversity of the gut microbiota (GM). Sixty male C57BL/6J mice were divided initially to two groups, the shifted group (n=30) exposed to circadian shifts for three months and the non-shifted group (n=30) under a normal light-dark cycle. The mice of the shifted group were cyclically housed for five days under the normal 12:12 hour light-dark cycle followed by another five days under reversed light-dark cycle. At the end of the three months a colitis was induced by 2 % DSS given in the drinking water of 30 mice. Animals were then divided into four groups (n=15 per group), sham group non-shifted (Sham-NS), sham group shifted (Sham-S) and DSS non-shifted (DSS-NS) and DSS shifted (DSS-S). Fecal samples were collected from rectal content to investigate changes in GM composition by DNA extraction followed by high-throughput sequencing of the bacterial 16S rRNA gene. The mouse GM was dominated by three phyla: Firmicutes, Bacteroidetes and Actinobacteria. The Firmicutes/Bacteroidetes ratio decreased in mice with induced colitis. The richness and diversity of the GM were reduced in the colitis group, especially in the group with inverted circadian rhythm. Moreover, GM composition was also modified in the inverted circadian rhythm group, with an increase in Alloprevotella, Turicibacter, Bacteroides and Streptococcus genera. Circadian rhythm inversion exacerbates GM dysbiosis to a less rich and diversified extent in a DSS-induced colitis model. These findings shows a possible interplay between circadian rhythm disruption, GM dynamics, and colitis pathogenesis.

The availability of multi-rotor UAVs with lifting capacities of several kilograms, allows for a new paradigm in atmospheric measurement techniques, i.e. the integration of research-grade sonic anemometers for airborne turbulence measurements. With their ability to hover and move very slowly, this approach yields an unrevealed flexibility compared to mast-based sonic anemometers, for a wide range of boundary layer investigations that require an accurate characterization of the turbulent flow. For an optimized sensor placement, potential disturbances by the propeller-induced flow (PIF), as well as the potential impact of the sensor weight and angular momentum on the flight performance in the case of a boom-mounted sensor, have to be considered.

A recent study revealed a persistent presence of the PP-Spike recombinant protein in 50% of individuals who received ModRNA injections, contrasting with unvaccinated controls, whether SARSCoV-2 infected or not, up to 187 days post-injection. The implications of these findings are discussed in the context of PP-Spike recombinant protein-induced hyperimmune/inflammatory reactions and thrombotic vasculitis as mechanisms to elucidate the serious side effects, long-term organ complications, and excess deaths observed after administering Covid ModRNA products. These results underscore the urgent need for a comprehensive reassessment of the risk-benefit profile of ModRNA injections, including an immediate halt in their use for any person, and a renewed emphasis on understanding and addressing their long-term effects on human health

Efficient implementation of clean energy technologies, including pioneering solutions like mobile solar PV systems mounted on trailers (MSPT), is pivotal for addressing energy challenges, especially in regions with constrained power grid access. This endeavour is vital for meeting escalating elec-tricity demands and aligning with the UN Sustainable Development Goal (SDG) aimed at ensuring dependable and sustainable energy provision in developing countries. This paper investigates the aerodynamic behaviour of a designed MSPT using numerical and experimental approaches. Spe-cifically, the study focuses on the effects of wind velocity and tilt angels on the drag and lift forces, as well as drag and lift coefficients on the panel used in the MSPT system. Additionally, the overall wind force acting on the entire MSPT (including 9 large solar PV panels) was examined, considering the combined effects of wind flow and the system's geometry. The simulations were conducted using ANSYS-Fluent software and experimental testing was performed utilizing scaled-down models to validate the accuracy of the simulation. The insights and the knowledge from this study can be utilized to optimize the design, installation, and operation of such systems, ultimately enhancing their performance, reliability, and paving ways for further improvements in mobile solar PV technology.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

The role of initial state (ISI) and final state (FSI) ion–ion interactions in heavy ion double charge exchange (DCE) reactions A(Z,N)→A(Z±2,N∓2) are studied in the context of double single charge exchange (DSCE) reactions given by sequential actions of the isovector nucleon–nucleon (NN) T–matrix. The second order DSCE reaction amplitude is investigated in momentum representation in a formulation, focused on the extraction of nuclear matrix elements under the conditions of strong initial state (ISI) and final state (FSI) interactions. In closure approximation and using the momentum representation, the reaction amplitude is finally separated into ISI/FSI distortion coefficients and reaction kernels and nuclear matrix elements. The ISI/FSI reaction kernels emerge as the result of the repeated scattering on the avoided volume, introduced by the imaginary parts of the ion–ion optical potential and acting as sinks for the quantal probability current. The closure approximation allows derive a set of induced effective two–body isotensor interactions, given by products of spin–scalar, spin–vector central and rank–2 spin–tensor interactions. The intermediate propagator plays a key role in establishing correlation between the DCE transitions in the projectile and target nucleus. The presented approach emphasizes the special features of DSCE reaction dynamics as proceeding like a system of two coupled isospin dipoles whose strengths are determined by the momentum-space form factors of the NN isovector interaction. The properties of the DSCE interaction form factors are investigated and the approach is applied to data.

Biomimetic design has recently received widespread attention. Inspired by the Terebridae structure, this paper provides a structural form for suppressing vortex-induced vibration (VIV) response. Four different structural forms are shown, including the traditional smooth cylinder (P0), the Terebridae-inspired cylinder with a helical angle of 30° (P30), the Terebridae-inspired cylinder with a helical angle of 60° (P60), and the Terebridae-inspired cylinder with a helical angle of 90° (P90). And computational fluid dynamics (CFD) method is adopted to solve the flow pass the Terebridae-inspired structures, and the vibration equation is solved using the Newmark-β method. The results show that the VIV responses are effectively controlled in the lock-in region for P30, P60, and P90, and P60 shows the best VIV suppression performance. The transverse amplitude and the downstream amplitude can be reduced by 82.67% and 91.43% respectively for P60 compared with that for P0, and the peak of the mean-drag coefficient is suppressed by 53.33%. The Q-criterion vortices of P30, P60, and P90 are destroyed, with irregular vortices shedding. It is also found that the boundary layer separation is located on the Terebridae-inspired ribs. The twisted ribs cause the separation point to constantly change along the spanwise direction, resulting in the development of the boundary layer separation being completely destroyed. The strength of the wake flow is significantly weakened for the Terebridae-inspired cylinder. In the lock-in region, the motion trajectory presents a typical 8-shaped for P0, while the motion trajectory of the Terebridae-inspired cylinder tends to be a flat 1-shaped.

Floating wind is becoming an essential part in terms of renewable energy. Therefore, highlighting the perspectives in developing the floating wind platforms is very important. In this paper, we focus on floating wind concepts and projects around the world. This will give a taste to the reader about what is going on in terms of the projects around the world. The main aim of this work is to further explain the collected data regarding the floating wind concepts and projects, and further classify them in terms of cost, power capacity, wind speed, water depth, and distance to shore.

Climate research shows that extreme weather events and their effects are increasing in frequency, severity, and impact. Extreme wind events can cause massive societal and economic damage. High wind occurrences and their causes must be identified because they are hard to define and understand. Extreme wind modeling affects wind power plant planning, installation, and building modeling. This applies to city, vegetation, and vegetational area modeling. The scientific literature utilizes statistical, dynamic (Weather Research and Forecasting-WRF), and machine learning methods to identify extreme wind speeds. This study explores the relationship between lower-level extreme wind speeds and upper-level parameters like Z500, and T850 based on cluster analysis. The aim is to explore the correlation between upper-level atmospheric dynamics and lower-level wind behavior. K-Means cluster analysis method was employed to classify Turkish regions with similar severe wind episodes. WRF model simulation findings from NEWA (New European Wind Atlas) project (2019) were used for that purpose. The NEWA project's wind speed data at 100m a.g.l. was used for cluster analysis. We simplify the process by grid point reduction and applying the top 2% percentile as threshold value. Self-Organized Maps (SOM) clustering was also applied using the upper-level variables.

The energy transition to wind and solar opens opportunities for green hydrogen as the wind and solar generation tends to bring electricity prices down to very low levels. This paper evaluates whether green hydrogen can integrate well with wind and solar PV to help with improved management of the South Australian electricity grid. Green hydrogen can use membrane electrolysis plants during surplus renewable energy periods. This hydrogen can then be electrified or used in industry. The green hydrogen system was analysed to understand the financial viability and technical impact of integrating green hydrogen. We also used systems engineering techniques to understand the system holistically, including the technical, social, environmental, and economic impacts. The results show opportunities for the system to provide seasonal storage, grid firming, and reliability services. Financially, it would need changes to electricity rules to be viable, but without those changes, our modelling suggested it would be financially viable within this decade