In this study, TiO2 nanostructured coatings on Ti-6A-4V alloys were fabricated by two methods: H2O2 oxidation and RF sputtering. In the annealing temperature range of 25 C - 500 C, there were the peaks at 35, 37, 40 and 52 corresponding to {100}, {002}, {101} and {102} crystal planes of hcp structure of α-Ti. At the annealing temperature of 600 C, there was the presence of peaks corresponding to crystal planes of anatase and rutile TiO2. The relative intensities of anatase and rutile phases of the sample fabricated by RF sputtering were 3.62 and 10.25 %, respectively; while those of the sample fabricated by H2O2 oxidation were 21.27 and 3.20 %, respectively (The relative intensity of α-Ti phase was 100 %). The results investigated the peak shift of α-Ti phase in TiO2/Ti-6Al-4V nanostructured coatings fabricated by the two methods which was reasonably explained from the difference in the thermal expansion coefficients of Ti alloy and TiO2 components, as well as the difference in the ratio of anatase to rutile phases.

The direct hydrogenation of greenhouse gas carbon dioxide (CO2) to higher alcohols (C2+OH), as an important research area in C1 chemistry, is one of the most essential approaches to convert CO2 into liquid fuels or other value-added chemicals. The high atom economy and direct pathway make this reaction attractive to convert CO2 to higher alcohols. However, due to the complicated reaction network and the difficulty of C-C coupling, the formation of higher alcohols is more difficult compared with methanol or other compounds containing one carbon. The key issue is development of novel catalysts with high conversion and space time yield. But this is still a huge challenge faced by researchers. In this review, the thermodynamics and reaction pathways of CO2 hydrogenation were firstly clarified. Subsequently, after reviewing single metal-based, bi-and multi-metallic catalysts, the recently progress of tandem catalytic system was emphasized. Finally, we also provided an overview about tandem catalysis for CO2 hydrogenation to higher alcohols.

This study investigates the role of oxygen vacancy on Fe-doped CeO₂ catalyst activity for soot oxidation. The oxygen vacancy was assessed through Ce³⁺ content. The Fe content was varied between 0 and 30% for two catalyst preparation methods, co-precipitation (CP) and solution combustion synthesis (SCS). X-ray photoelectron spectroscopy indicates that ceria exists as both Ce₄₊ and Ce₃₊, while iron is present only as Fe₃₊. The catalyst’s activity was evaluated by ignition (T10) and combustion (T50) temperatures using thermogravimetric analysis. Optimum Fe contents yielding the highest activity were found to be 10% and 5% for CP and SCS catalysts, respectively. The surface area and morphology have shown moderate effect on catalyst activity, because catalytic soot oxidation involves solid-solid contact. More importantly, regardless of the fabrication method, it was found that Ce₃₊ content, which is closely related to oxygen vacancies, plays the most important role in affecting the catalyst activity.

Reverse water gas shift reaction (RWGS) is an important process which plays a vital role in many CO2 utilization related reactions. Noble metals are the most active catalysts in RWGS, but the high price and low reserve strangled their applications. In the present work, we reported a non-transition-metal MgAl2O4 catalyst which showed outstanding activity and stability at high temperatures in the RWGS reaction and improved performance after doping of single atomic Nin+. The catalyst can obtain 46% of CO2 conversion in durability test of 75 h at 800 °C under high weight hourly space velocities (225 000 ml g-1 h-1). The adsorption sites, possible reaction route, and effects of Nin+ single atoms on the (111) surface of MgAl2O4 for RWGS were investigated by in situ DRIFTS and DFT calculations. The results indicated that the rate determining reaction step of RWGS on MgAl2O4 and Ni (SA)/MgAl2O4 were both the reaction of OH* + H* → H2O* + *, but the energy barrier was significantly reduced after introducing single atomic Nin+. Nin+ atoms can increase the hydroxyl coverage on the surface of catalyst and Al3+ sites near the Nin+ ion are considered as the predominant active sites for RWGS reactions.

Silver ion (Ag+) are recognized for their potent antibacterial properties; however, their utilization in food preservation is restricted by factors such as inadequate stability, a transient antibacterial impact, and the potential for human absorption. Hydrogel-based antibacterial agents are capable of exerting their antibacterial effects by establishing appropriate microenvironments, which facilitate the efficient delivery of antimicrobial molecules to the contaminated regions of food. In previous studies, we observed that chitosan (CS) and silver nitrate (AgNO3) were able to reduce Ag+ to silver nanoparticles (AgNPs) with enhanced antibacterial properties. This not only significantly extended the stability of the antibacterial agent but also demonstrated exceptional inhibitory capabilities against pathogenic bacteria, including common grape contaminants such as P. expansum, A. niger, and B. cinerea. Utilizing ultrasound-induced complexation technology, this study has successfully synthesized a chitosan-silver (CS-AgNPs) hydrogel. The efficacy of this hydrogel against the pathogenic fungus responsible for jujube black spot disease has been thoroughly investigated. The morphology structures of CS-AgNPs hydrogels were characterized by TEM, FTIR and UV-vis. The results indicated that AgNPs ranging from 80 to 110 nm were uniformly dispersed within the gel matrix and remained stable for extended periods at room temperature. In vitro antibacterial assays and fractional inhibitory concentration index (FICI) studies revealed that the pronounced antibacterial efficacy of the CS-AgNPs hydrogel was primarily attributed to the additive antibacterial effect of CS and AgNPs. These insights underscore the significant potential of CS-AgNPs hydrogels in combating fungal diseases of jujube, offering innovative strategies and materials for the management of agricultural pathogens.

In this study, a new method for synthesizing Ag-NaYF4:Yb3+/Er3+ @ SiO2 nanocomposites was introduced. Using a hydrothermal method, the synthesized Yb3+- and Er3+-codoped NaYF4 upconversion luminescent materials and Ag nanoparticles were doped into upconversion nanomaterials and coated with SiO2 up-conversion nanomaterials. This material is known as Ag-UCNPs-SiO2’ it improves both the luminous intensity because of the doped Ag nanoparticles and has low cytotoxicity because of the SiO2 coating. The morphology of UCNPs was observed using scanning electron microscopy (SEM), and the mapping confirmed the successful doping of Ag nanoparticles. Successful coating of SiO2 was confirmed using transmission electron microscopy (TEM). Fluorescence spectra were used to compare changes in luminescence intensity before and after doping Ag nanoparticles. The reason for the increase in luminescence intensity after doping with Ag nanoparticles was simulated using first-principles calculations. The cytotoxicity of Ag-UCNPs-SiO2 was tested via the cell counting kit-8 (CCK-8) method, and its imaging ability was characterized using the micro-CT method.

Metallic elements of higher economic value occurring in the mineralogy of Zimapán are Pb, Zn, Cu and Fe, said elements are sold as concentrates, which, even after processing, generally include significant concentrations of Mo, Cd, Sb, Ag and As that could recover through different leaching methods. In this work the influence of temperature was studied in the complexation of silver in the S₂O₃^2--O₂ system. Chemical and mineralogical characterization of concentrated Zn from the state of Hidalgo confirmed the presence of the silver contained in a sulfide of silver arsenic (AgAsS₂) through the techniques of Atomic Absorption Spectrophotometry (AAS), X-Ray Diffraction (XRD) and Scanning Electron Microscopy-Energy-Dispersive X-Ray Spectroscopy (SEM-EDS). The mineralogical species identified allowed the construction mineralogical species Pourbaix diagrams in the range of 298 K to 333 K, through which the Eh-pH conditions to obtain silver in solution were determined. The formation of Ag(S₂O₃)₂^3- complex was confirmed by characterizing liquors leached using the technique Infrared Spectroscopy Fourier Transform (FTIR).

The Covid-19 pandemic and the initial focus on handwashing measures have again highlighted the importance of water access as an essential service in protecting human health. Yet, especially in southern cities, uneven geographies of water access – often mediated by fragmented and unequal infrastructure systems – may hamper the fight against infectious diseases. The spread of SARS-CoV-2 presented a dilemma for water providers as well as residents in water-deprived urban areas as they had to adhere to new hygiene standards and requirements, despite limited access to basic water infrastructure. Therefore, a deeper understanding of pandemic urban waterscapes – the infrastructure and governance systems as well as everyday practices and technologies – is necessary for ongoing debates on (post-) pandemic or zoonotic cities. In our paper, we focus on changes in urban (water) governance and government water projects in Nairobi since early 2020. We show that Covid-19 has contributed to changes in Nairobi’s waterscape but only in conjunction with recent changes in the city’s overall governance structure. However, if these waterscape changes lead to greater equity in water access, and if they have helped to curb the spread of SARS-CoV-2, is more than questionable.

The fundamental mechanism underlying negative-ion catalysis involves bond-strength breaking in the transition state (TS). Doubly-charged atomic/molecular anions are proposed as novel dynamic tunable catalysts and demonstrated in water oxidation to peroxide. Density Functional Theory TS calculations have found tunable energy activation barrier reduction ranging from 0.030 eV to 2.070eV, with Si²ˉ, Pu²ˉ, Pa²ˉ and Sn²ˉ the best catalysts; the radioactive elements usher in new application opportunities. C₆₀²ˉ reduces significantly the standard C₆₀ˉ TS energy barrier while graphene increases it, behaving like cationic systems. Rank-ordered catalysts according to their reaction barrier reduction efficiency, variation across charge states and systems reveal their tunable and wide applications, ranging from water purification to biocompatible anti-viral and anti-bacterial sanitation systems.

In this study, silver-strontium doped hydroxyapatite (AgSr-HA)/chitosan composite coatings were deposited on stainless steel (SS) substrate via electrophoretic deposition (EPD) technique. The EPD parameters such as the concentration of Ag Sr-HA particles in the suspension, applied voltage and deposition time were optimized on by the Taguchi Design of Experiment (DoE) approach. DOE approach elucidated that the “best” coating was obtained at; the deposition voltage of 20V, deposition time of 7 minutes, and at 5 g/L of Ag Sr-HA particles in the suspension. The optimum coatings were characterized by using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy. SEM images confirmed the deposition of chitosan/Ag Sr-HA on the SS substrate. The wettability studies indicated the hydrophilic nature of the chitosan/Ag Sr-HA coatings, which confirmed the suitability of the developed coatings for orthopedic applications. The average surface roughness of the chitosan/Ag Sr-HA coatings was in a suitable range for the attachment of bone marrow stromal cells. Chitosan/Ag Sr-HA coatings showed a potent antibacterial effect against the Gram-Positive and Gram-negative bacteria.

In the face of the current energy and environment problems, the full use of biomass resources instead of fossil energy to produce a series of high-value chemicals has great application prospects. 5-hydroxymethylfurfural (HMF), which can be synthesized from lignocellulose as raw material, is an important biological platform molecule. Its preparation and catalytic oxidation of subsequent products have important research significance and practical value. In the actual production process, porous organic polymer (POPs) catalysts are highly suitable for biomass catalytic conversion due to its high efficiency, low cost, good designability, and environmentally friendly features. Here, we briefly described the application of various types of POPs (including COFs、PAFs、HCPs、CMPs) in the preparation and catalytic conversion of HMF from lignocellulosic biomass, and analyzed the influence of the structural properties of catalysts for the catalytic performance. Finally, we summarized some challenges that POPs catalysts will face in biomass catalytic conversion, and prospected the important research directions in future. This review would provide valuable references for the efficient conversion of biomass resources into high-value chemicals in practical applications.

Removing one key barrier to the industrial uptake of green chemistry and nanocatalysis in the fine and specialty chemical industry requires to fill an ongoing “talent shortage” via expanded chemistry education. In this study we show how the use of hybrid sol-gel catalysts to synthesize fine chemicals and active pharmaceutical ingredients in flow chemistry reactors illustrates new ideas to reshape chemistry education based on recent research outcomes, visualization and digital tools. Several lessons learned from the industrial and academic utilization of these materials in continuous-flow conversions conclude the study.

The Computational theoretical techniques using first principle which make use of the density functional theory as implemented by quantum expresso as well as inter – atomic force constant (IFC) techniques (Born-von Jarman) were used to investigate the phonon dispersion curves of Silver (Ag) and Gold (Au) The results obtained show that for Au, the extension to 1 – 6^th neighbour gave slightly close agreement with the experimental phonon dispersions when compared to the 1 – 5^th neighbor at W_T and L_L symmetry points. The percentage error for Au at W_T are 2.5% and 2.9% ; at point L_L we obtained 0.6% and 0.7% respectively. The Local density Approximation (LDA) results for Ag underestimates the lattice with about 1.6% while the Generalized Gradient Approximation (GGA) overestimates it by 1.9%.

A series of Zn-modified Hβ (Zn/Hβ) catalysts were prepared by using the different zinc precursors such as ZnSO4·7H2O, ZnCl2, C4H6O4Zn·2H2O and Zn(NO3)2·6H2O, and their catalytic performance in the ethanol conversion to propylene reaction was evaluated. Results indicate the amount and strength distribution of acid sites of the Zn/Hβ catalysts were easily tuned by employing different type of zinc precursors. More importantly, when the Zn species were introduced to the Hβ, the propylene yield was significantly enhanced, whereas the yields of the byproducts such as ethylene and C2-C4 alkanes were remarkably suppressed. For the catalyst prepared by using the ZnCl2 precursor (Zn/Hβ-C), a higher propylene yield up to 43.4% was achieved as a result of the moderate amount and distribution of acid sites. The average coking rate of the used Zn/Hβ catalysts strongly depended on the amount of total acid sites, especially the strong acid sites, i.e., the higher the amount of total acid sites of the catalyst, the greater the average coking rate. For the catalyst prepared by using the ZnSO4·7H2O precursor, Zn/Hβ-S exhibited a better stability even after depositing more coke, which is due to the higher amount of strong acid sites.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

In this work, the ternary titanium, copper and silver (Ti-Cu-Ag) system is investigated as a potential candidate for the production of mechanically robust biomedical thin films. The coatings are produced by physical vapor deposition-magnetron sputtering (MS-PVD). The composite thin films are deposited on a silicon (100) substrate. The ratio between Ti and Cu was approximately kept one, with the variation of the Ag content between 10 and 35 at.%, while the power on the targets is changed during each deposition to get the desired Ag content. Thin film characterization is performed by x-ray diffraction (XRD), nanoindentation (modulus and hardness) and Atomic force microscopy to determine the surface topography. The residual stresses are measured by focused ion beam and digital image correlation method (FIB-DIC). The produced Ti-Cu-Ag thin films appear to be smooth, uniformly thick and exhibit amorphous structure for the Ag contents lower than 25 at.%, with a transition to partially crystalline structure for higher Ag concentrations. The Ti-Cu control film shows higher values of 124.5 GPa and 7.85 GPa for modulus and hardness respectively. There is a clear trend of continuous decrease in the modulus and hardness with the increase of Ag content, as lowest value of 105.5 GPa and 6 GPa for 35 at.% Ag containing thin films. In particular, a transition from the compressive (-36.5 MPa) to tensile residual stresses between 229 MPa and 288 MPa are observed with an increasing Ag content. The obtained results suggest that the Ag concentration should not exceed 25 at.%, in order to avoid an excessive reduction of the modulus and hardness with maintaining (at the same time) the potential for an increase of the antibacterial properties. In summary, Ti-Cu-Ag thin films shows characteristic mechanical properties that can be used to improve the properties of biomedical implants such as Ti-alloys and stainless steel.

In this work, magnetic CuFe₂O₄/Ag nanoparticles activated by porous covalent organic frameworks (COF) was fabricated to evaluate the heterogenous reduction of 4-nitrophenol (4-NP). The core-shell CuFe₂O₄/Ag@COF was successfully prepared by polydopamine reduction of silver ions on CuFe₂O₄ nanoparticles, followed by COF layer condensation. With integrating the intrinsic characteristics of the magnetic CuFe₂O₄/Ag core and COF layer, the obtained nanocomposite exhibited features of high specific surface area (464.21 m² g^-1), ordered mesoporous structure, strong environment stability, as well as fast magnetic response. Accordingly, the CuFe₂O₄/Ag@COF catalyst showed good affinity towards 4-NP via π-π stacking interactions and possessed enhanced catalytic activity compared with CuFe₂O₄/Ag and CuFe₂O₄@COF. The pseudo-first-order rate constant of CuFe₂O₄/Ag@COF (0.77 min^-1) is 3 and 5 times higher than CuFe₂O₄/Ag and CuFe₂O₄@COF, respectively. The characteristics of bi-catalytic CuFe₂O₄/Ag and the porous COF shell of CuFe₂O₄/Ag@COF made a contribution to improve the activity of 4-NP reduction. The present work demonstrated a facile strategy to fabricate COF activated nano-catalysts with enhanced performance in the fields of nitrophenolic wastewater treatment.

The surface enhanced fluorescence（SEF）detection bases by plasmonic nanopillars array with nanoparticles has opened up a new gate in the application of biological imaging and sensing. The fluorescence enhancement of the probe molecule depends on its position in equilibrium, which is close to the hot spot leading to the electromagnetic field enhancement, but not too close to the metal surface resulting in quenching. Here, a large scale SiO₂-Ag-cicada wing SEF substrate was fabricated by magnetron sputtering with correction enhancement factor of 797.6. Thereinto the cicada wing provides the skeleton of the nanopillars array structure, the deposited Ag constructs two kinds of hot spots, and SiO₂ forms a separation layer to prevent quenching. Moreover, the substrate exhibited good reproducibility, high sensitivity with low limits of detection (LOD) and high stability for oxidation resistance. We propose that SEF substrate with modification of SiO₂ can not only improve the enhancement performance, but also expanding its application in the biological investigations.

Photocatalytic decomposition of ethylene was performed under UV-Led irradiation at the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on the porous nickel foam. Process was carried out in the high temperature chamber with regulated temperature from ambient to 125°C under flow of reacted gas (ethylene in a synthetic air, 50 ppm) with simultaneous FTIR measurements of sample surface. Ethylene was decomposed with higher efficiency in elevated temperatures with maximum of 28% at 100-125°C. The nickel foam used as support for TiO2 allowed to enhance the ethylene decomposition at the temperature of 50°C. However, at 50°C the stability of ethylene decomposition was not retained within the following reaction run, but it was at 100°C. Performed photocatalytic measurements at the presence of some radicals scavengers indicated that higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and increased formation of superoxide anionic radicals, which were formed at the interface of thermally activated nickel foam and TiO2.

Read-Across Structure-Activity Relationship (RASAR) is an emerging cheminformatic approach that combines the usefulness of a QSAR model and similarity-based Read-Across predictions. In this work, we have generated a simple, interpretable, and transferable quantitative-RASAR (q-RASAR) model which can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials. The data set involves 29 TiO2-based nanomaterials which contain specific amounts of noble metal precursors in the form of Ag, Au, Pd, and Pt. The data set was rationally divided into training and test sets and the Read-Across-based predictions for the test set were generated using the tool Read-Across-v4.1 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. The hyperparameters were optimized based on the training set data and using this optimized setting, the Read-Across-based predictions for the test set were obtained. The optimized hyperparameters and the similarity approach, which yields the best predictions, were used to calculate the similarity and error-based RASAR descriptors using the tool RASAR-Desc-Calc-v2.0 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. These RASAR descriptors were then clubbed with the physicochemical descriptors and were subjected to features selection using the tool Best Subset Selection v2.1 available from https://dtclab.webs.com/software-tools. The final set of selected descriptors was used to develop multiple linear regression based q-RASAR models, which were validated using stringent criteria as per the OECD guidelines. Finally, a random forest model was also developed with the selected descriptors. The final machine learning model can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials superseding previously reported models in the prediction quality.

Herewith we report a facile synthesis of zinc oxide doped with (5, 10, 15, and 20 wt%) titanium oxide nanocomposites in gelatin under ultra-sonication. The X-ray diffraction (XRD) data revealed ZnO the formation in addition to a rutile phase TiO2. The ZnO phase size decreased, and the rutile TiO2 phase increased with a TiO2 loading increment. The scanning electron microscopy (SEM) displayed a combination of spherical and hexagonal particles with a 60 – 80 nm size distribution. The prepared nanostructures photocatalytic activity was assisted using Rhodamine B dye, where they showed enhanced photodegradation competence under visible light irradiation. The kinetics of photodegradation followed the first-order kinetics with the 20 % wt sample having the maximum activity. The mechanistic investigation revealed the dominance of h+ and •O2- species during the dye photodegradation. The results indicate the potential application of such gelatin stabilized nanostructures for dye illumination from aqueous solutions under sunlight.

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS₃), a layered semiconductor that attracted much attention recently thanks to its quasi-1D electronic and optoelectronic properties and its direct bandgap of 1.1 eV. Heating TiS₃ in air above 300 °C gradually converts it into TiO₂, a semiconductor with a wide bandgap of 3.2 eV with applications in photo-electrochemistry and catalysis. In this work, we investigate the controlled thermal oxidation of individual TiS₃ nanoribbons and its influence on the optoelectronic properties of TiS₃-based photodetectors. We observe a step-wise change in the cut-off wavelength from its pristine value ~1000 nm to 450 nm after subjecting the TiS₃ devices to subsequent thermal treatment cycles. Ab-initio and many-body calculations confirm an increase of the bandgap of titanium oxysulfide (TiO_2-xS_x) when increasing the amount of oxygen and reducing the amount of sulfur.

Photoelectrocatalytic water splitting by using various TiO₂ nanostructures is a promising approach to generate hydrogen without harmful byproducts. However, their effective performance is restricted by some drawbacks such as high rapid electron-hole pair recombination and backward reaction producing H₂O. Thus in this study, the probability of enhancing hydrogen generation rate by adding methanol as a sacrificial agent to the anodic chamber of a two-compartment photoelectrochemical cell is investigated. Herein, one-dimensional elongated TiO₂ nanorods that were fabricated via a facile one-pot hydrothermal method are utilized as potent photoanode. Voltammetric characterizations confirm that addition of alcoholic sacrificial agent has a significant effect on photoelectrochemical properties of TiO₂ nanorods which by adding 10 wt% of methanol, the photocurrent density and photoconversion efficiency increased from 0.8mA.cm^-2 to 1.5mA.cm^-2 and from 0.28% to 0.45%, respectively. The results of photoelectrocatalytic water splitting indicated that the hydrogen generation rate in the presence of methanol was about 1.2 times higher than that from pure water splitting. These enhancements can be attributed to the key role of methanol. Methanol molecules not only inhibit the electron-hole pair recombination but also accelerate the hydrogen generation rate by sharing their hydrogen atoms.

PdRe/Al2O3 catalysts are highly selective for hydrogenation of furfural to furfuryl alcohol (FAL). Moreover, synergy between the metals can result in greater specific activity (higher turnover frequency, TOF) than exhibited by either metal alone. Bimetallic catalyst structure depends strongly on the metal precursors employed and their addition sequence to the support. In this work, PdRe/Al2O3 catalysts were prepared by: (i) co impregnation (CI) and sequential impregnation (SI) of  Al2O3 using HReO4 and Pd(NO3)2, (ii) SI using NH4ReO4 and [Pd(NH3)4(NO3)2], (iii) HReO4 addition to a reduced and passivated Pd/Al2O3 catalyst, and (iv) impregnation with the double complex salt (DCS), [Pd(NH3)4(ReO4)2]. Raman spectroscopy and temperature-programmed reduction (TPR) evidence larger supported PdO crystallites in catalysts prepared using Pd(NO3)2 than [Pd(NH3)4(NO3)2]. Surface [ReO4]- species detected by Raman exhibit TPR peak temperatures from ranging 85 to 260°C (versus 375°C for Re/Al2O3). After H2 reduction at 400°C, the catalysts were characterized by chemisorption, temperature-programmed hydride decomposition (TPHD), CO diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), and scanning transmission electron microscopy (STEM) with energy-dispersive x-ray (EDX) spectroscopy. The CI catalyst containing supported Pd-Re alloy crystallites had a TOF similar to Pd/Al2O3 but higher (61%) FAL selectivity. In contrast, catalysts prepared by methods (ii-iv) containing supported Pd-Re nanoparticles exhibit higher TOFs and up to 78% FAL selectivity.

Network effects, economies of scale, and lock-in-effects increasingly lead to a concentration of digital resources and capabilities, hindering the free and equitable development of digital entrepreneurship (SDG9), new skills, and jobs (SDG8), especially in small communities (SDG11) and their small and medium-sized enterprises (“SMEs”). To ensure the affordability and accessibility of technologies, promote digital entrepreneurship and community well-being (SDG3), and protect digital rights, we propose data cooperatives [1,2] as a vehicle for secure, trusted, and sovereign data exchange [3,4]. In post-pandemic times, community/SME-led cooperatives can play a vital role by ensuring that supply chains to support digital commons are uninterrupted, resilient, and decentralized [5]. Digital commons and data sovereignty provide communities with affordable and easy access to information and the ability to collectively negotiate data-related decisions. Moreover, cooperative commons (a) provide access to the infrastructure that underpins the modern economy, (b) preserve property rights, and (c) ensure that privatization and monopolization do not further erode self-determination, especially in a world increasingly mediated by AI. Thus, governance plays a significant role in accelerating communities’/SMEs’ digital transformation and addressing their challenges. Cooperatives thrive on digital governance and standards such as open trusted Application Programming Interfaces (APIs) that increase the efficiency, technological capabilities, and capacities of participants and, most importantly, integrate, enable, and accelerate the digital transformation of SMEs in the overall process. This policy paper presents and discusses several transformative use cases for cooperative data governance. The use cases demonstrate how platform/data-cooperatives, and their novel value creation can be leveraged to take digital commons and value chains to a new level of collaboration while addressing the most pressing community issues. The proposed framework for a digital federated and sovereign reference architecture will create a blueprint for sustainable development both in the Global South and North.

The effects of various drawing parameters and annealing processes on the structure and properties of Cu-Ag wires, containing 1 wt% silver, were investigated using specialized equipment including fine wire drawing machines, very fine wire drawing machines, heat treatment equipment, tensile testing machines, microcomputer-controlled electronic universal testers, resistance testers, and scanning electron microscopes. The results revealed that continuous drawing of Cu-1%Ag alloy wires led to elongation of the grains, resulting in a uniform and tightly fibrous microstructure. Moreover, the tensile strength of the alloy wire increased from 670 MPa to 783.9 MPa after a single-pass with a deformation of 14%. Subsequently, when the wire was drawn at a speed of 500 m/min, the tensile strength further increased to 820.1 MPa. After annealing the Փ0.08 mm Cu-1% Ag alloy wire, an increase in annealing temperature up to 500°C resulted in the wire's tensile strength decreasing from 820.1 MPa to 377.5 MPa. Simultaneously, the elongation increased from 1.94% to 15.21%, and the resistivity decreased from 1.931×10-8Ω·m to 1.723×10-8Ω·m. Additionally, when annealing was conducted at a rate of 80 m/min, the wire resistivity dropped to 1.635×10-8Ω·m.

Streptococcus mutans is well known for having virulence factors associated with its cariogenic role, such as glucosyltransferases, which have been used as targets for the virtual screening of molecules with inhibitory capacity. The Antigen I/II of S. mutans is involved in the adhesion to the surface of the tooth and the bacterial co-aggregation in the biofilm formation, despite that, this protein has not been used as a target in a virtual strategy search for inhibitors. In this study we identified in silico and evaluated in vitro molecules with adhesion inhibitory potential on S. mutans Ag I/II. A virtual screening of 883,551 molecules was conducted, cytotoxicity analysis on fibroblast cells, S. mutans adhesion studies, scanning electron microscopy analysis for bacterial integrity, and molecular dynamics simulation were also performed. We have found three molecules (ZI-187, ZI-939, ZI-906) that were not cytotoxic and inhibited the adhesion of S. mutans to polystyrene microplates. Molecular dynamic simulation by 300 nanoseconds showed stability of the interaction between ZI-187 and Ag I/II (PDB: 3IPK). This work provides three new molecules that targets Ag I/II and have the capacity to inhibit in vitro the S. mutans adhesion on polystyrene microplates and provides a new computational line for the search and selection of safe inhibitory molecules against different pathogens.

PEBAX-2533/metal salt/Al salt membranes were prepared for mixed olefin/paraffin separation. PEBAX-2533 with 80% ether group and 20% amide group was suggested as the polymer matrix for comparison of separation performance according to the functional group ratio in copolymer PEBAX. In addition, Al salts were used to stabilize metal ions for a long time as additives. High permeance was expected with the proportion of high ether groups since these functional groups provided relatively permeable regions. As a result, the PEBAX-2533 composite membrane showed a selectivity of 5 (propylene/propane) with 10 GPU. However, the permeance of membrane was not unexpectedly improved and the selectivity was reduced. The result was analyzed by SEM, FT-RAMAN and TGA, including FT-IR. The reduction in separation performance was determined by FT-IR. From these results, in order to stabilize the metal ions interacting with the polymer through Al(NO3)3, it was concluded that specific ratio of amide group was needed in PEBAX as polymer matrix.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

Indonesia is one of the largest banana producing countries in the world remaining abundance solid waste of banana fruit bunch. The banana fruit bunch contains high natural fibers which were obtained by an impregnation process using potassium hydroxide (KOH) and followed by a carbonization process under steam at 250°C for 5 h. The nanomaterial of TiO₂/fibre was prepared by a hydrothermal process at 200°C for 4 h. Surface morphology proved that the TiO₂ was loaded into the fibre by an increasing roughness of the surface and irregular size of porosity. The development of amorphous to crystalline phase of TiO₂/fibre was clearly observed. The effectiveness of TiO₂/fibre for removal of rhodamine B was investigated from different parameters of adsorptions in aqueous solution. The equilibrium adsorptions show that the Langmuir and Freundlich isotherm exhibited the best correlation coefficient (R² > 0.94) relating to the chemisorption and physisorption interaction in the adsorption process. Kinetic models were well described by the pseudo-first and second-order with the best correlation coefficient (R² > 0.99). These results indicate that nanomaterial TiO₂/fibre can be used as an effective adsorbent for removal of rhodamine B in aqueous solution.

Increasing photon absorption by capturing light is an important way to increase the efficiency of photovoltaic devices. In this regard, the small optical band gap (Eg) and high absorption coefficient of Se-containing thin nanofilms make them ideal for next generation photovoltaic devices based on selenides. This study reports on chemical synthesis processes in a bath for the insertion of amorphous selenium into polyamide-6 (PA 6) matrix and the effect of incorporation of Cd2+ and Ag+ on the structural, morphological and optical properties. The resulting films had a pyramidal structure of single crystals, nanosized particles of nonspecific shape, agglomerated and indistinct grains. ATR-FTIR spectroscopy revealed the interaction between PA 6 and inorganic components, which causes obvious conformational changes in PA 6 chains. The data of X-ray diffraction analysis, depending on the stage of synthesis, showed a mixture of various compounds: Se8, CdSe, Ag2Se and Ag. This may explain the observed optical properties. The optical properties of the composites indicate a shift in the band gap from 4.46 eV for PA 6 to 2.23-1.64 eV upon stepwise insertion of amorphous Se, Cd2+ and Ag+ ions. Eg is conveniently located in the visible region of solar energy, making the obtained nanofilms ideal for solar energy harvesting.

Small rodents and insectivores are potential reservoirs of many pathogens transmissible to humans such as bacteria, parasites and viruses responsible for epidemics in sub-Saharan Africa, particularly in West Africa. Few studies on small mammal species in the Kolikoro and Sikasso regions are available, hence the interest in investigating the different species of small rodents and insectivores, and their role in the transmission of pathogens to humans. The study aims to identify commensal small mammal species circulating in Faladjè and Bougouni areas, and likely to represent major risks of epidemic disease emergence. Sessions of trapping were carried out in December 2016 in Faladjè and Bougouni with wire mesh traps type “Besançon tous services” (BTS) baited with peanut butter and/or onion. All animals captured were identified morphologically. Out of 123 small rodents and insectivores captured in 674 trap nights, 75 (60.97%) were from Faladjè and 48 (39.02%) from Bougouni, Of these, six species of small rodents belong to the family Muridae (Mastomys erythroleucus, Mastomys natalensis, Rattus rattus, Praomys daltoni, Gerbilliscus gambianus, Taterillus gracilis) and two species of insectivores associated with the genus Crocidura spp. belong to the family Soricidae and Erinaceidae (Crocidura cf olivieri and Atelerix cf albiventris) respectively. There is low specific diversity within these two stands, but the variation in relative abundance is significant (binomial test, p = 0.018 ˂ 0.05) between the Faladjè and Bougouni stands of small mammals. Mastomys erythroleucus was the most dominant species (57.33%, 43/75) in the Faladjè settlement and R. rattus dominated (37.5%,18/48) that of Bougouni. These two species of small mammals are potentially involved in the transmission of bacteria, parasites and pathogenic viruses to humans.

This narrative review critically evaluates the multidimensional impacts of team sports on student wellness through the Wellness Wheel framework, encompassing physical, emotional, intellectual, social, spiritual, occupational, and environmental well-being. Methodologically, the review synthesizes empirical studies, systematic reviews, and meta-analyses from the last 20 years, extracted from databases such as PubMed, PsycINFO, Scopus, Web of Science, and Google Scholar, to construct a comprehensive understanding of how team sports contribute to holistic student development. Our findings highlight team sports as a vital component of educational and wellness programs, significantly enhancing not just physical health but also emotional stability, cognitive performance, social skills, spiritual enrichment, and environmental awareness. The review underscores the necessity of integrating team sports into educational curricula to promote a balanced and comprehensive approach to student well-being. It also identifies existing gaps in literature, particularly the need for further research on enhancing inclusivity and accessibility in team sports, ensuring that all students can benefit from their wide-ranging impacts. This study advocates for strategic initiatives to incorporate team sports in educational settings, emphasizing their essential role in cultivating a well-rounded, healthy, and inclusive student body.

The efficiency and performance of Proton Exchange Membrane Fuel Cells (PEMFCs) are primarily influenced by ORR electrocatalysts. In recent years, atomically dispersed met-al-nitrogen-carbon (M-N-C) catalysts have gained significant attention due to their high active center density, high atomic utilization, and high activity. These catalysts are now considered the preferred alternative to traditional noble metal electrocatalysts. The unique properties of M-N-C catalysts are anticipated to enhance the energy conversion efficiency and lower the manufac-turing cost of the entire system, thereby facilitating the commercialization and widespread ap-plication of fuel cell technology. This article initially delves into the origin of performance and degradation mechanisms of Fe-N-C catalysts from both experimental and theoretical perspectives. Building on this foundation, the focus shifts to strategies aimed at enhancing the activity and durability of atomically dispersed Fe-N-C catalysts. These strategies encompass the use of bi-metallic atoms, atomic clusters, heteroatoms (B, S, and P), and morphology regulation to optimize catalytic active sites. The article concludes by detailing the current challenges and future pro-spects of atomically dispersed Fe-N-C catalysts.

The increading emission of carbon dioxide to the atmosphere has urged the scientific community to investigate alternatives to alleviate such emissions being the principal contributor to the greenhouse gas effect. One major alternative is carbon capture and utilisation (CCU) towards the production of value-added chemicals using diverse technologies. This work aims at the study of the catalytic potential of different cobalt-derived nanoparticels for methanol syntheis from carbon dioxide hydrogenation. Thanks to its abundance and cost-efficacy, cobalt can serve as an economical catalyst compared to noble-metal-based catalysts. In this work, we present a systematic comparison among different cobalt and cobalt oxide nanocomposites in terms of their efficiency as catalysts for carbon dioxide hydrogenation to methanol as well as how different supports can enhance their catalytic capacity. The oxygen vacancies in the cerium oxide act as carbon dioxide adsorption and activation sites, which facilitates a higher methanol production yield.

In the FCC conversion of heavy petroleum fractions as atmospheric residues, the main challenge for refiners to achieve the quantity and quality of various commercial products depends essentially on the catalyst used in the process. A deep characterization of the catalyst at different steps of the process (fresh, regenerated, and spent catalyst) was investigated to study the catalyst's behavior including the physicochemical evolution, the deactivation factor, and kinetic-thermodynamic parameters. All samples have been characterized by various spectroscopy methods such as N2 adsorption-desorption, UV-visible spectroscopy, Raman spectroscopy, LECO carbon analysis, Scanning electron microscopy (SEM), X-ray diffraction (XRD), X‐ray fluorescence (XRF), nuclear magnetic resonance spectroscopy (NMR13C) analysis, and Thermogravimetric analysis. The results of N2 adsorption-desorption, UV-vis, Raman, LECO carbon, and SEM images showed that the main causes of catalyst deactivation and coking were the deposition of carbon species that covered the active sites and clogged the pores, and the attrition factor due to thermal conditions and poisonous metals. The XRD and XRF results showed the catalyst’s physicochemical evolution during the process and the different interlinks between catalyst and feedstock (Nickel, Vanadium, Sulfur, and Iron) elements which should be responsible for the coking and catalyst attrition factor. It has been found that, in addition to the temperature, the residence time of the catalyst in the process also has an influence on catalyst structure transformation. NMR13C analysis revealed that polyaromatic hydrocarbon is the main component in the deposited coke of the spent catalyst. Thermogravimetric analysis showed that the order of catalyst mass loss was fresh > regenerated > spent catalyst due to the progressive losses of the hydroxyl bonds (OH) and the structure change along the catalyst thermal treatment. Moreover, the kinetic and thermodynamic parameters showed that all zones are non-spontaneous endothermic reactions.

Using of the organic base tetramethylammonium hydroxides (TMAH) is a viable, cheap and fast route, for the MgZnAl-LDH type materials synthesis by both co-precipitation and mechano-chemical methods. TMAH provided several advantages as smaller quantity of water required in the washing step compared to the use of inorganic alkalis, prevention of LDH contamination with alkali cations, acting as template molecule in texture tailoring along with disadvantages as its presence in small quantities in the resulting layered materials. Regardless the use of organic / inorganic bases and co-precipitation / mechano-chemical methods, zincite stable phase was found in all the synthesized solids. The basicity of catalysts followed the trend: mixed oxides > reconstructed > parent LDH. The memory effect of LDH is supported only by the presence of Mg and Al cations, while Zn remains as zincite stable phase. The catalytic activities for Claisen-Schmidt condensation of benzaldehyde with cyclohexanone provided values higher than 90% after 2h, with a total selectivity in 2,6-dibenzylidenecyclohexanone, while in self-condensation of cyclohexanone no more than 7.29% after 5h. These behaviors depended on catalysts basicity as well as the planar rigidity of the compound.

This work focuses on the support effect on the performances of Co-based catalysts for the acetic acid steam reforming. SBA-15, a well ordered hexagonal mesoporous silica structure, and CeO2 have been selected as the supports, with the impact of chromium addition also being investigated. Better acetic acid steam reforming performances have been recorded for CeO2 compared to SBA-15 supported catalysts and, in particular, the 7Co/CeO2 catalyst showed the highest values of acetic acid conversions with enhanced H2 yields below 480°C, in comparison to the other investigated catalytic formulations. In addition, more pronounced coke depositions and acetone concentrations have been obtained with CeO2 supported catalysts, due to the tendency of ceria to catalyse the ketonization reaction. Chromium addition to Co/SBA-15 catalysts led to an enhancement in the activity towards acetic acid steam reforming, while on CeO2 supported catalysts no improvement in the catalysts activity was observed; however, on both SBA-15 and CeO2 supported catalysts, Cr addition reduced the amount of coke deposited on the catalysts surface.

A series of MgAl-layered double hydroxide (MgAl-HT), the calcined form at 500^oC (MgAlO_x) and the re-hydrated one at 25^oC (MgAl-HT-RH) were synthesized. Physicochemical properties of the catalysts were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM). Surface area of the as-synthesized, calcined and re-hydrated catalysts was determined by N₂ physisorption at -196^oC. CO₂-teperature programmed desorption (CO₂-TPD) was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1-15) were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90^oC in liquid phase, or under microwave irradiation method. The mesoporous structure and basic nature of re-hydrated solid catalyst were responsible for their superior catalytic efficiency. The robust nature was determined by using the same catalyst for five times, where the product % yield was almost unchanged significantly.

Abstract: Circuit breakers are affected by multiple lightning strikes after the breaker has been tripped and can break down again, which will reduce the life of the circuit breaker and threaten the stable operation of the power system. Aiming at this problem, the paper obtained the temperature diffusion process of the inrush current process of circuit breaker opening and breaking through the schlieren technique, and combined with the existing image recognition technology to obtain the temperature characteristics of the airflow in the air gap of the contact, and the characteristics of the airflow flow. The results of the study show that the circuit breaker breakdown process generates a shock wave with a velocity approximately equal to the speed of sound under the same conditions. The maximum velocity of the airflow boundary diffusion is about 1/4 of the speed of sound under the same condition, and it decays very fast, reducing to the airflow drift velocity within 10ms after breakdown. The maximum temperature of the thermals is concentrated between 6000 and 8000 K and the temperature change is approximately inversely proportional to the square of time. The research provides the basis for the design of circuit breaker contact structure, opening speed optimization method, interrupter chamber and insulation design optimization.

We successfully fabricated Ag@Cu2O core-shell decorated on reduced graphene oxide (rGO) nanocomposites (ACRN) by a simple and convenient in situ substitution method. The properties of these ACRN with heterostructure layers were characterized by scanning and transmission electron microscopies and absorption spectroscopy. We used p-nitrophenol (4-NP) as a probe molecule to determine the chemical catalytic activity of the ACRN. Upon introduction of rGO, a high electron transfer efficiency was achieved; thus, the catalytic activity was improved significantly. Therefore, the ACRN exhibited significantly improved catalytic activity for the reduction of 4-NP and showed the high application value in the removal of toxic and harmful substances from water. In addition, the fabricated ACRN was used for the reduction of organic dyes and explosive pollutants to generate nontoxic products. Furthermore, the high charge redistribution and transfer among Ag, Cu2O and rGO in the ACRN induced the high catalytic reduction of organic pollutants, indicating the excellent potential of these materials for applications in water pollution treatment.

Bond Properties were performed on Ag-2.35Au-0.7Pd-0.2Pt-0.1Cu alloy wire with a diameter of 25 µm under different process parameters. Effects of electrical flaming off (EFO) current and EFO time on deformability of the free air ball (FAB) were investigated using scanning electron microscopy (SEM) as well as the effects of ultrasonic power and bonding force on the bond characteristic. The experimental results showed that, FAB grows from a preheated tip to a small ball, a regular ball and finally to a golf ball with increasing either the EFO current or the EFO time, and the FAB presented optimal shape at 25 mA and 650 μs. Moreover, a nonlinear relationship between FAB diameter and EFO time is obtained at the EFO current of 25 mA, which could be expressed by a cubic equation. Further, at a constant bonding force, as the ultrasonic power increased, the mashed ball diameter grew larger and larger, the capillary hole imprint became more and more obvious, and the tail width also increased larger and larger, and vice versa. The optimal ultrasonic power and bonding force are 70 mW and of 45 gf for ball bond and 90 mW and 75 gf for wedge bond, respectively. Finally, for all the bonded wire samples prepared under optimal process parameters, no ball and wedge bond lifts happened after destructive pull test, and full intermetallic compound coverage with perfect morphology occurred on the bond pad after ball shear test, which meant that the bonded wire samples have high bond strength, and hence improved the reliability of microelectronic products.

Fresh Ag nanoparticles (NPs) dispersed on a transparent SiO2 exhibit an intense optical extinction band originating in localized surface plasmon resonance (LSPR) in visible range. The intensity of LSPR band weakened when the Ag NPs was stored in ambient air for two weeks. The rate of the weakening and the LSPR wavelength shift, corresponding to visual chromatic changes, strongly depended on the environment in which Ag NPs were set. The origin of a chromatic change was discussed along with both compositional and morphological changes. In one case, bluish coloring followed by a prompt discoloring was observed for Ag NPs placed near the ventilation fan in our laboratory, resulted from adsorption of large amounts of S and Cl on Ag NP surfaces as well as particle coarsening. Such color changes deduce the presence of significant amounts of S and Cl in the environment. In other case, a remarkably blue-shift of LSPR band was observed for the Ag NPs stored in the desiccator made of stainless steel, originated in the formation of CN and/or HCN compounds and surface roughening. Their color changed from maroon to reddish, suggesting that such molecules were present inside the desiccator.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

The removal of sulfur from fossil fuels is one of the most important processes in modern refineries. It is accomplished via hydrodesulfurization (HDS) of the sulfur organic compounds in presence of heterogeneous catalysts. In the current work, heterogeneous catalysts containing cobalt and mo-lybdenum supported on mesoporous materials type SBA-15 and AlSBA-15 were synthesized for application in the HDS reactions of thiophene in n-heptane stream. The mesoporous materials were synthesized by hydrothermal method starting from TEOS, pseudobohemite, hydrochloric ac-id and water. Pluronic P123 was used as template. The best calcination conditions for removal of the organic template were optimized by thermogravimetry analysis (TG/DTG). The calcined SBA-15 and AlSBA-15 supports were submitted to co-impregnation with solutions of cobalt nitrate and ammonium heptamolybdate, aiming the production of 15% in mass of metal loading with atomic ratio of [Co/(Co+Mo)]=0.45. The obtained materials were dried and calcined for obtaining the mesoporous catalysts in the form of CoMo/SBA-15 and CoMo/AlSBA-15. The catalysts were char-acterized by XRD, TG/DTG, SEM and nitrogen adsorption. From XRD analysis, it was verified that after decomposition of the cobalt and molybdenun salts, were formed MoO3, Co3O4 and Co-MoO4 oxides on the supports, being attributed to these chemical species the activity for the HDS reactions. The activity of the obtained catalysts was evaluated in a continuously flowing tubular fixed-bed microreactor coupled on-line to a gas chromatograph, using n-heptane stream contain-ing 12070 ppm of thiophene (ca. 5100 ppm of sulfur) as a model compound. From the catalytic tests it was verified that the synthesized catalysts presented good activity for the reaction, and the main obtained products were cis- and trans-2-butene, 1-butene, n-butane and low amounts of iso-butane. The presence of 1,3-butadiene and tetrahydrothiophene (THT) were not detected. A mechanism of the primary and secondary reactions and subsequent formation of the olefins and paraffins, in the CoMo/SBA-15 and CoMo/AlSBA-15 mesoporous catalysts were proposed, con-sidering steps of desulfurization, hydrogenation, dehydrogenation, THT decyclization and isomerization.

Four different Mn and Re catalysts for electrochemical CO2 reduction have been studied by IR spectroelectrochemistry (SEC) in dry acetonitrile. In the case of Mn(apbpy)(CO)3Br (apbpy= 4(4-aminophenyl)-2,2’-bipyridine) SEC suggests that a very slow catalytic reduction of CO2 occurs in acetonitrile also in the absence of proton donors, but at rather negative potentials. On the contrary, the corresponding Re(apbpy)(CO)3Br clearly displays a slow catalytic conversion already at the first reduction potential. Switching to saturated CO2 solutions in a mixture of acetonitrile and 5% of water as proton donor, the SEC of Mn(apbpy)(CO)3Br displays faster catalytic behavior.

In this work, pure TiO₂ and binary nanocomposites of Fe₃O₄/TiO₂ and Ag/TiO₂ were synthesized in order to improve photocatalytic performance of these samples for degradation of 2, 4-dichlorophenol (2, 4-DCP) as an organic pollutant. A range of analytical techniques including XRD, DRS, SEM/EDX, and elemental mapping were employed to reveal the crystal structure, morphology and property of the nanocomposites. XRD data demonstrated that the prepared samples are purely in TiO₂ anatase phase and cubic spinel Fe₃O₄ exist in the synthesized nanocomposite. We calculated the TiO₂ crystal size from XRD patterns, in the range of 8.35-11.09 nm. The presence of Ag, Fe, O, and Ti atoms in the synthesized nanocomposites was confirmed by SEM/EDX. We obtained 30.43, 32.02 and 42.40 % degradation of 2, 4-DCP (100 ml 2, 4-DCP 40 ppm and 0.01 g catalyst) for pure TiO₂, Fe₃O₄/TiO₂ and Ag/TiO₂, respectively, after 180 min of irradiation under visible light. Similar conditions were employed for 2, 4-DCP degradation under UV irradiation, we obtained 53.05, 51.00 and 71.50 % degradation of 2, 4-DCP pure TiO₂, Fe₃O₄/TiO₂ and Ag/TiO₂, respectively. Thus, the synthesized binary nanocomposites exhibited higher photocatalytic activity compared to pure TiO₂ under visible light.

The integration of clean energy generation with wastewater treatment holds promise for addressing both environmental and energy concerns. Focusing on photocatalytic hydrogen production and wastewater treatment, the study introduces PdIn/TiO2 catalysts for the simultaneous removal of the pharmaceutical contaminant paracetamol and hydrogen production. Physicochemical characterization showed a high distribution of Pd and In on the support as well as a high interaction with it. The Pd and In deposition enhances the light absorption capability and significantly improved HER in comparison to TiO2 not only in the electrolyte but also in presence of paracetamol. Regarding PTM oxidation, TiO2 and PdIn/TiO2 showed an irreversible behavior toward the PTM oxidation, limited by the adsorption of species on the electrode surface. Thus, PdIn-doped TiO2 stands out as a promising catalyst, showcasing enhanced physicochemical properties and superior catalytic performance. This underscores its potential for both environmental remediation and sustainable hydrogen production.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

Herein, we report about the monometallic Ni and bimetallic Pd-Ni catalysts supported on CeO2-Al2O3 binary oxide, which were investigated in oxy-steam reforming of methanol (OSRM). Monometallic and bimetallic supported catalysts were prepared by wet aqueous impregnation and subsequent impregnation method, respectively. The physicochemical properties of the catalytic systems were investigated using various methods such as: BET, XRD, TPR-H2, TPD-NH3, XPS and SEM-EDS techniques. It has been proven that the addition of palladium to the nickel catalyst facilitates its reduction. The activity tests performed for all catalysts confirmed the promotion effect of palladium on catalytic activity of nickel catalyst and selectivity towards hydrogen production. Both nickel and bimetallic palladium-nickel supported catalysts showed excellent stability during the reaction. Such catalytic systems are valuable for the advance of the field of fuel cell technology.

The catalytic decomposition of methane (CDM) process produces hydrogen in a single stage and avoids the CO₂ emission thanks to the formation of high added value carbon nanofilaments as by-product. In this work, Ni monometallic and Ni-Co, Ni-Cu and Ni-Fe bimetallic catalysts are tested in the CDM reaction for the obtention of fishbone carbon nanofibers (CNF). Catalysts, in which Al₂O₃ is used as textural promoter in their formulation, are based on Ni as main active phase for the carbon formation and on Co, Cu or Fe as dopants in order to obtain alloys with an improved catalytic behaviour. Characterization of bimetallic catalysts showed the formation of particles of Ni alloys with a bimodal size distribution. For the doping content studied (5 mol. %), only Cu formed an alloy with a lattice constant high enough to be able to favor the carbon diffusion through the catalytic particle against surface diffusion, resulting in higher carbon formations, longer activity times and activity at 750 °C, where Ni, Ni-Co and Ni-Fe catalysts were inactive. On the other hand, Fe also improved the undoped catalyst performance presenting a higher carbon formation at 700 °C and the obtention of narrow carbon nanofilaments from active Ni₃Fe crystallites.

Layered double hydroxides (LDHs) have emerged as promising catalysts for various acid-base catalytic reactions. Due to their unique structure and regulatable dual acid-base properties, they offer more environmentally friendly and sustainable alternatives to traditional liquid acid and base catalysts. This study introduces the structural composition, preparation methods, and acid-base catalytic properties of LDHs-based catalysts. Recent application progress of LDHs and rehydrated LDHs, LDHs-based metal nanocatalysts, and LDHs-based mixed metal oxide catalysts used as solid acid-base catalysts in acid-base green catalytic conversion is reviewed. The challenges and prospects of LDHs-based catalysts as green and sustainable catalysts are summarized and proposed.

Electrochemical Promotion was used to modify the activity and selectivity of a Rh catalyst-electrode in the CO2 hydrogenation reaction. The experiments were carried out in a temperature range of 350-430οC at ambient pressure and at different CO2 to H2 gas feeding ratios (1:2 to 4:1). The only reaction products observed were CO and CH4, both under open and closed-circuit conditions. The CH4 formation rate was found to increase with both positive and negative potential or current application. The CO formation rate followed the opposite trend. The selectivity to CH4 increased under high values of hydrogen partial pressure and decreased at high pressures of CO2. The results demonstrate how Electrochemical Promotion can be used to finely tune activity and selectivity for a reaction of high technical and environmental importance.

This work is devoted to the study of active and stable nickel catalysts for methane dry reforming based on Pr-doped ceria-zirconia obtained by solvothermal continuous method. The studies of physicochemical and catalytic properties of the 5%Ni\Ce0.75Zr0.25-xPrxO2 series showed that Pr introduction leads to an increase in the amount of highly reactive oxygen of the oxide lattice. Praseodymium-based catalysts showed significantly higher reactant conversions. In addition to the nature of support, the method of nickel introduction was also studied - Ni was added both by impregnation and one-pot with mixed oxide preparation. The method of Ni addition was shown to have significant effect on the morphology of the supported active component and, respectively, on the catalytic activity. The 5%Ni/Ce0.75Zr0.15Pr0.1O2 catalyst prepared by one-pot method showed stable operation in the MDR reaction for 30 hours at CO2 and CH4 conversions of ~40% and an H2 yield of ~18% (Т=700°С, τ=10ms).

In this work the influence of the structure forming agent on the composition, morphology and oxygen reduction reaction (ORR) activity of Fe-N-C catalysts was investigated. As structure forming agent (SFA), dicyandiamide (DCDA) (nitrogen source) or oxalic acid (oxygen source) or mixtures thereof were used. For characterization, cyclic voltammetry and rotating disc electrode (RDE) experiments were performed in 0.1 M H2SO4. In addition to this, N2 sorption measurements and Raman spectroscopy were performed for the structural characterization. The role of metal, nitrogen and carbon sources within the synthesis of Fe-N-C catalysts has been pointed out before. Here, we show that the optimum in terms of ORR activity is achieved if both N- and O-containing SFAs are used in almost similar fractions. All catalysts display a redox couple, whereat its position depends on the fractions of SFAs. The SFA has also a strong impact on the morphology: Catalysts that were prepared with a larger fraction of N-containing SFA revealed a higher order in graphitization, indicated by bands in the 2nd order range of the Raman spectra. Nevertheless, the optimum in terms of ORR activity is obtained for the catalyst with highest D/G band ratio. Therefore, the results indicate that the presence of an additional oxygen-containing SFA is beneficial within the preparation.

Background: Mounting evidence supports the role of the endocannabinoid system in neurophysiology, includ-ing blood-brain barrier (BBB) function. Recent work has demonstrated that activation of endocannabinoid re-ceptors can mitigate insults to the BBB during neurological disorders, like traumatic brain injury, cortical spreading depression and stroke. As alterations to the BBB are associated with worsening clinical outcomes in these conditions, studies herein sought to examine the impact of endocannabinoid depletion on BBB integrity. Methods: Barrier integrity was investigated in vitro via bEnd.3 cell monolayers to assess endocannabinoid syn-thesis, barrier function, calcium influx, junctional protein expression, and proteome-wide changes. Results: In-hibition of 2-AG synthesis using DAGLα inhibition and siRNA inhibition of DAGLα led to loss of barrier in-tegrity via altered expression of VE-cadherin, which could be partially rescued by exogenous application of 2-AG. Moreover, the deleterious effects of DAGLα inhibition on BBB integrity showed both calcium and PKC (protein kinase C)-dependency. Conclusions: These data indicate that disruption of 2-AG homeostasis in brain endothelial cells, in the absence of insult, is sufficient to disrupt BBB integrity thus supporting the role of the endocannabinoid system in neurovascular disorders.

Novel effluent treatment solutions for dangerous organic pollutants are crucial worldwide. In recent years, chemical reduction using noble metal-based nanocatalysts and NaBH4, a reducing agent, has become common practice for eliminating organic contaminants from aquatic environments. We suggest a straightforward approach to synthesizing magnetic cellulose nanocrystals (CNC) modified with magnetite (Fe3O4) and silver nanoparticles (Ag NPs) as a catalyst for organic contamination removal. Especially, Ag NPs were decorated on the CNC surface without reducing agents or stabilizers by reducing AgNO3. XRD, FE-SEM, TEM, EDX, VSM, BET, and zeta potential tests characterized the Ag/Fe3O4/CNC nanocomposite. The nanocomposite's catalytic activity was tested by eliminating 4-nitrophenol (4-NP) and organic dyes methylene blue (MB) and methyl orange (MO) in an aqueous solution at 25 oC. The Ag/Fe3O4/CNC nanocomposite reduced 4-NP and decolored these hazardous organic dyes in short time (2 to 5 min) using a tiny amount of catalyst (2.5 mg for 4-NP and 15 mg for MO and MB). The magnetic catalyst was removed and reused three times without losing catalytic activity. This work shows that the Ag/Fe3O4/CNC nanocomposite can chemically reduce harmful pollutants in effluent for environmental applications.

Worldwide emission standards are now required to cover engine operation under extreme ambient conditions, which affect the raw emissions and the efficiency of the exhaust aftertreatment systems. These regulations also target new combustion technologies for decarbonization, such as neat hydrogen (H2) combustion or dual-fuel strategies, which involve a challenge to the analysis of exhaust aftertreatment systems requirements and performance. This work addresses the impact of high altitude and low ambient temperature conditions on the reactivity of an oxidation catalyst in the presence of H2. A reaction mechanism is proposed to cover the main conversion paths of CO, HC, and H2, including the formation and consumption of high-energy surface reaction intermediates. The mechanism has been implemented into a faster-than-real-time reduced-order model for multi-layer washcoat honeycomb catalytic converters. The model was utilized to investigate the effect of H2 concentration on the reactivity of CO and HC within the catalyst under various operating and ambient conditions. By applying the model and examining the selectivity towards different reaction pathways in the presence H2, insights into surface intermediates and reactivity across different cross-sections of the monolith were obtained. This analysis discusses the underlying causes of reactivity changes promoted by H2 and its relative importance as a function of driving boundary conditions.

Hydrodechlorination reaction of 3-(benzo-1,3-dioxol-5-yl)-3-chloro-2-methylacrylaldehyde in the presence of different low metal content heterogeneous mono- or bi-metallic catalysts was tested for the synthesis of the fragrance Helional® (3-[3,4-methylendioxyphenyl]-2-methyl-propionaldehyde). In particular, mono Pd/Al2O3, Rh/Al2O3 or bi-metallic Pd-Cu/Al2O3, Rh-Cu/Al2O3 catalysts were tested in different reaction conditions from which it emerged that mono-Rh/Al2O3 was the best performing catalyst allowing to achieve 100% substrate conversion and 99% selectivity towards Helional® in 24h at 80°C, p(H2) 1.0 MPa in the presence of a base. To establish correlations between atomic structure and catalytic activity, catalysts were characterized by Cu, Rh and Pd K-edge XANES, EXAFS analysis. These characterizations allowed to verify that the formation of Pd-Cu alloys and the presence of Cu oxide/hydroxide species on the surface of the Al2O3 support, are responsible for the very low catalytic efficiency of bimetallic species tested.

Dehydroaromatization of methane (MDA) is of great interest as a promising process for processing natural and associated petroleum gases, the main component of which is methane. The rapid loss of catalyst activity because of coke formation hinders the introduction of the DHA methane process into industry. Therefore, the aim of the research was to find ways to improve Mo/ZSM-5 catalysts for MDA. The paper presents the results of the synthesis of high-silica zeolites of the ZSM-5 type with a microporous and micro-mesoporous structure, the preparation of Mo/ZSM-5 catalysts based on them, and the study of the physicochemical and catalytic properties of the obtained samples during the non-oxidative conversion of methane into aromatic hydrocarbons. Zeolite catalysts were investigated by IR spectroscopy, X-ray diffraction, TPD-NH3, SEM, HR-TEM, N2-adsorption. It was found that the addition of carbon black at the stage of synthesis of zeolite type ZSM-5 does not lead to structural changes, the obtained samples have a crystallinity equal to 100%. The creation of the micro-mesoporous structure in Mo/ZSM-5 catalysts lead to an increase in their activity and stability in the process of methane dehydroaromatization. The highest conversion of methane is observed on a 4.0%Mo/ZSM-5 catalyst prepared based on of zeolite synthesized using 1.0% carbon black, and is 13.0% in 20 minutes of reaction, while the benzene yield reaches 7.0%. It has been shown by HR-TEM that a more uniform distribution of the active metal component is observed in a zeolite catalyst with a micro-mesoporous structure than in a microporous zeolite.

The use of biolubricants as an alternative for petroleum-based products has played an important role in the last decade. Thus, due to the encouragement of global policies, which mainly support green chemistry and circular economy, there has been an increasing interest in bio-based products, including biolubricants, from scientific and industrial points of view. Due to the different applications of biolubricants for a wide range of practical uses, the raw materials, production, and characteristics might vary, making this field a continuously changing subject of study by researchers. The aim of this research work was to focus on biolubricant production from vegetable oil crops in a bio-refinery perspective, paying attention to the main raw materials used, the corresponding production methods (with special focus on double transesterification), the role of catalysts and techno-economic studies. Thus, the main factors affecting quality parameters such as viscosity or oxidative stability have been covered, including catalyst addition, reaction temperature or the use of raw materials, reagents or additives were also analyzed. The latest research trends were included, updating previous studies about this matter, considering current conclusions and future research.

Phosphorus, an essential rare element in aquatic ecosystems, plays a key role in maintaining ecosystem balance. However, an excess of phosphorus will lead to eutrophication and algal pro-liferation. To prevent eutrophication, it is crucial to pretreat and measure the concentration of total phosphorus (TP). Compared with conventional TP pretreatment equipment (autoclave), a lab-on-a-chip detection device fabricated through micro-electromechanical system technology using titania (TiO2) as a photocatalyst is more convenient, efficient, and cost-effective. However, the wide bandgap of TiO2 (3.2 eV) limits the photocatalytic activity. To address this problem, this paper describes the preparation of a TiO2/Au nanocomposite film by electron-beam evaporation and atomic layer deposition, based on the introduction of a gold film and TiO2 on a quartz substrate. The photocatalytic degradation properties of TiO2/Au nanocomposite films with thicknesses of 1, 2, 3, and 4 nm are assessed using rhodamine B as a pollutant. Experimental results demonstrate that the deposition of a gold film with different thicknesses can enhance the photocatalytic degradation efficiency through synergetic reactions in the charge separation process on the surface. The optimal photocatalytic efficiency is achieved when the deposition thickness is 2 nm, and it decreases with further increase in the thickness. When the photocatalytic reaction time is 15 min, the LOC device with a 2-nm-thick gold layer and autoclave exhibit similar TP pretreatment performance. Therefore, the proposed LOC device based on photocatalysis technology can address the limitation of conventional autoclave equipment, such as large volume, long processing time, and high cost, thereby satisfying the growing demand for on-site evaluation.

In this paper, the phases in the Mg-Ti-O system using the 1:1 formulation of MgO:TiO2 mixing synthetic brucite of Mexican origin with TiO2 microparticles of high purity and with a heat treatment at 1100°C for 1 h were studied. The raw materials and formulation by XPS and DRX techniques were characterized. The results demonstrate the presence of different oxidation states in titania and the formation of different oxides in the Mg-Ti-O system when mixed and calcined at 1100°C; additionally, the formation of vacancies in the crystal lattice during the transformation from hexagonal brucite to magnesia with a cubic structure centered on the faces is estimated. With the results, its thermal behavior is warned based on the MgO-TiO2 phase diagram.

Transparent binder is used to substitute conventional black asphalt binder and to provide light-colored pavements, whereas nano-TiO2 has the potential to promote photocatalytic and self-cleaning properties. Together, these materials provide multifunction effects and benefits when the pavement is submitted to high solar irradiation. This paper analyses the physicochemical and rheological properties of a transparent binder modified with 0.5%, 3.0%, 6.0%, and 10.0% of nano-TiO2 and compares it to the transparent base binder, and conventional and polymer modified binders (PMB) without nano-TiO2. Their penetration, softening point, dynamic viscosity, master curve, black diagram, Linear Amplitude Sweep (LAS), Multiple Stress Creep Recovery (MSCR), and Fourier-Transform Infrared Spectroscopy (FTIR) were obtained. The transparent binders (base and modified) seem to be workable considering their viscosity and exhibited values between the conventional binder and PMB regarding rutting resistance, penetration, and softening point. They showed similar behavior as the PMB, demonstrating signs of polymer-modification. The addition of TiO2 seems to reduce fatigue life, except for the 0.5% content. Nevertheless, its addition in high contents increases the rutting resistance. The TiO2 modification seems to have little effect on the chemical functional indices. The best percentage of TiO2 was 0.5%, considering fatigue and 10.0% concerning permanent deformation.

Hydrogen peroxide (H2O2) is an essential analyte for detecting neurodegenerative diseases and in-flammatory processes and plays a crucial role in pharmaceutical, food industry, and environmental monitoring. However, conventional H2O2 detection methods have drawbacks such as lengthy analysis time, high costs, and bulky equipment. Non-enzymatic sensors have emerged as promising alternatives to overcome these limitations. In this study, we introduce a simple, portable, and cost-effective non-enzymatic electrochemical sensor based on carbon black (CB) and silver nano-particle-modified δ-FeOOH (Ag/δ-FeOOH), integrated into a disposable electrochemical cell (DCell). Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and electrochemical impedance spectroscopy (EIS), confirmed successful CB and Ag/δ-FeOOH immo-bilization on the DCell working electrode. Electrochemical investigations revealed that the DCell-CB//Ag/δ-FeOOH sensor exhibited an approximately twofold higher apparent heterogene-ous electron transfer rate constant than the DCell–Ag/δ-FeOOH sensor, capitalizing on CB ad-vantages. Moreover, the sensor displayed excellent electrochemical response for H2O2 reduction, boasting a low detection limit of 22 µM and a high analytical sensitivity of 214 μA mM-1 cm-2. Notably, the DCell-CB//Ag/δ-FeOOH sensor exhibited outstanding selectivity for H2O2 detection, even in potential interferents such as dopamine, uric acid, and ascorbic acid. Furthermore, the sensor demonstrated its suitability for monitoring H2O2 in complex biological samples, as evidenced by H2O2 recoveries ranging from 92% to 103% in 10% fetal bovine serum. These findings underscore the considerable potential of the DCell-CB//Ag/δ-FeOOH sensor for precise and reliable H2O2 monitoring in diverse biomedical and environmental applications.

Taking advantage of fact that the surface electrons of metallic nanoparticles (NPs) can be effectively released even at a low voltage bias, we demonstrate an improvement in the electrochemical performance of nano-sized Prussian Blue (PB) based secondary batteries by the incorporation of bare Ag or Ni NPs onto the vicinity of the working PB NPs. It is found that the capacity for electrochemical energy storage of the 17-nm-PB-based battery is significantly higher than the capacity of 10-nm-PB-based, 35-nm-PB-based or 46-nm-PB-based batteries. There is a critical PB size for the highest electrochemical energy storage efficiency. The full specific capacity CF of the 17-nm-PB-based battery stabilized to 62 mAh/g after 130 charge-discharge cycles at a working current of IW = 0.03 mA. The addition of 14 mass-percent of Ag NPs in the vicinity of the PB NPs gives rise to a 32% increase in the stabilized CF. A 42% increase in the stabilized CF can be obtained with the addition of 14 mass-percent of Ag NPs on the working electrode of the 35-nm-PB-based battery. An enhancement of CF is also found for electrodes incorporating bare Ni NPs but the effect is smaller.

Surface-enhanced Raman spectroscopy (SERS) can boost the pristine Raman signal by ~ 108 times that could be exploited for producing innovative sensing devices with advanced properties. However, the inherent complexity of SERS systems restricts their further applications in rapid detection, especially in situ detection in narrow aera. Here, we construct an efficient and flexible SERS-based LOP sensor by integrating Ag/Au nanocap arrays obtained by Ag/Au coating polystyrene nanospheres on the optical fiber face. We obtain rich “hotspots” at the nanogaps between neighboring nanocaps and further achieve the excellent SERS performance with the assistance of laser induced thermophoresis on the metal film that can achieve high efficiency aggregation of detected molecules. We achieve a high Raman enhancement with a low detection limitation of 10-7 mol/L for the most efficient samples based on the above sensor. This sensor also exhibits good repeatability and stability under multiple detections, revealing the potential application in situ detection based on the reflexivity of optical fiber.

This studies the plasmonic properties of the bimetallic quantum dot Ag@Au core-shell nanostructures embedded in the non-absorbent host medium. Local field enhancement factor and coefficient of absorption of Ag-core and Au-shell are primarily studied based on quasi-static approximation of classical electrodynamics for 6-10 nm composite radius. In this quantum dot geometry, two set of plasmonic resonances in visible spectral region are observed: the first resonance associated with inner interface of gold (Ag@Au) and the second resonance associated with outer interface of gold (Au@medium). The two plasmonic resonances are close each other and enhanced when the size of composite decreased for a fixed core size while shifted to in opposite direction and the amplitude of peak decreased when the core size is increased for a fixed composite size. For the optimized size of core/composite or shell thickness and other parameters to the desired values, such type of composites are recommended for various applications like; photocatalysis, biomedical, nano-optoelectronics.

The chemical synthesis of silver nanoparticles (Ag-NPs) by using an environmentally friendly methodology for their preparation is presented. Thus, considering that plants possess components that can act as reducing agents and stabilizers in the nanoparticles production, in this work, the synthesis of Ag-NPs by using a solution of grape waste extract as reducing and capping agent is studied. First, the total polyphenols content and reducing sugars in extracts produced at different conditions are characterized. After that, Ag-NPs are synthesized regarding the interaction of Ag ions (from silver nitrate) and the grape waste extract. The effect of temperature, contact time, extract/metal solution volume ratio and pH solution in the synthesis of metal nanoparticles are studied too. Different sets of nanoparticle samples are fully characterized by means of Electron Microscopy coupled with Energy Dispersive X-Ray for qualitative chemical identification. Ag-NPs with an average diameter of 27.7 ± 0.6 nm are selected to proof their suitability for sensing purposes. Thus, screen-printed electrodes modified with Ag-NPs are tested for the simultaneous voltammetric stripping determination of Pb(II) and Cd(II). Results indicate good reproducibility, sensitivity and limits of detection around 2.7 µg L⁻¹ for both metal ions.

Monometallic (Ni, Co, Cu) and bimetallic (Ni-Co, Ni-Cu) 10-20 wt. % metal containing catalysts supported on fly ash zeolite were prepared by post-synthesis impregnation method. The catalysts were characterized by X-ray powder diffraction, N2 physisorption, XPS and H2-TPR methods. Finely dispersed metal oxides and mixed oxides were detected after the decomposition of impregnating salt on the relevant zeolite support. By reduction intermetallic, NiCo and NiCu phases were identified in the bimetallic catalysts. Hydrogeoxygenation of lignocellulosic biomass-derived levulinic acid to γ-valerolactone (GVL) was studied. Bimetallic, 10 wt. % Ni, 10 wt. % Cu or Co containing fly ash zeolite catalyst showed higher catalytic activity than monometallic ones. Their selectivity to GVL reached 70-85 % at 100 % conversion. The reaction proceeds through formation of 4-hydroxy pentanoic acid, as the only intermediate compound.

Starting from the environmental issues related to global warming, climate change and reduction of greenhouse gas emissions, this review paper describes how CO₂ recycling can represent a challenging strategy suitable to explore new concepts and opportunities for catalytic and industrial development. In this view, the production of dimethyl ether (DME) from catalytic hydrogenation of CO₂ appears as a viable technology, able to meet also the ever-increasing need for alternative environmentally-friendly fuels and energy carriers. Basic considerations on thermodynamic aspects controlling DME production from CO₂ are presented, then summarizing the main catalytic systems developed in such a field. Special attention is paid on the role assumed during last years by zeolite-based systems, either in the methanol-to-DME dehydration step or in the one-pot CO₂-to-DME hydrogenation. On the whole, the productivity of DME results significantly to be dependent on several catalyst features, linked not only to the metal-oxide phase responsible for CO₂ activation/hydrogenation, but also to specific properties of the zeolites (i.e., topology, porosity, surface area, acidity, interaction with active metals, distributions of metal particles, …) influencing activity and stability of hybridized bifunctional heterogeneous catalysts.

The present review revisits representative studies addressed to develop efficient carbon-based heterogeneous catalysts for two important reactions, namely, the production of hydrogen from formic acid and the hydrogenation of carbon dioxide to formic acid. The HCOOH-CO2 system is considered a promising couple for a hydrogen storage system that would be involved in an ideal carbon-neutral cycle. Significant advancements have been achieved in those catalysts designed to catalyze the dehydrogenation of formic acid under mild reaction conditions, while much effort is still needed to catalyze the challenging CO2 hydrogenation reaction. The design of carbon-based heterogeneous catalysts for these reactions encompasses both the modulation of the properties of the active phase (particle size, composition, and electronic properties), as well as the modification of the supports by means of incorporation of nitrogen functional groups. These approaches are herein summarized to provide a compilation of the strategies followed in recent studies to set the basis for a hydrogen storage system attained by the HCOOH-CO2 couple.

FeZnNa@SiO2-C catalyst with graphitized carbon (GC) modified mesoporous SiO2 support metal nanoparticles was prepared by sol-gel method. The effect of adding metal Na and Zn promoters as a dispersion on the CO2 hydrogenation to low olefins was systematically studied. The results showed that Zn-Na, as a combination, promoted the absorption of CO2 and improved the conversion rate of CO2. Na as an alkaline substance can improve the absorption of more acidic CO2, improving the conversion rate of CO2 to 59.03%. Meanwhiles, addition of secondary metal Zn into Fe-based catalysts to form a surface alloy could alter the adsorption of CO2 and the activation of C-O bonds, inhibit the subsequent hydrogenation of olefins to paraffins, facilitate the reduction of Fe2O3 and the formation of active Fe5C2 species. From TEM and XRD, the formation of active Fe5C2 species was found, the selectivity of the target product was 41.07%. The deep hydrogenation of olefins is inhibited, by inhibiting their deep hydrogenations, the STY of C2=-C4= was raised again, up to 0.0436. However, the corresponding STY does not increase infinitely with the increase of Na content, and when the Na content to 6.4%, which can be shown higher CO2 hydrogenation catalytic performance. Compared with Fe@SiO2-C catalyst, Na and Zn promoted Fe-based catalysts prepared by modified sol-gel method, can be used directly for highly efficient CO2 hydrogenation to low olefins and thus will be more promising in the future.

A series of chiral complexes of the form Ir(NHC)2(aa)(H)(X) (NHC = N-heterocyclic carbene, aa = chelated amino acid, X = halide) was synthesized by oxidative addition of -amino acids to iridium(I) bis-NHC compounds and screened for asymmetric transfer hydrogenation of ketones. Following optimization of the reaction conditions, NHC, and amino acid ligands, high enantioselectivity was achieved when employing the Ir(IMe)2(l-Pro)(H)(I) catalyst (IMe = 1,3-dimethylimidazol-2-ylidene), which asymmetrically reduces a range of acetophenone derivatives in up to 95% enantiomeric excess.

In this paper, the catalytic combustion of DMDS (dimethyl disulfide, CH₃SSCH₃) over bimetallic supported catalysts were investigated. It was confirmed that Cu/γ-Al₂O₃-CeO₂ showed best catalytic performance among the five single-metal catalysts. Furthermore, six different metals were separately added into Cu/γ-Al₂O₃-CeO₂ to investigate the promoting effect. The experiments revealed Pt as the most effective promoter and the the best catalytic performance was achieved as the adding amount of 0.3 wt%. The characterization results indicated that high activity and resistance to sulfur poisoning of Cu-Pt/γ-Al₂O₃-CeO₂ could be attributed to the synergistic effect between Cu and Pt.

Microplastics (plastic particles < 5 mm) are ubiquitous pollutants that pose the ability to carry microbiota, including pathogens. Microbial adhesion is usually a sign of pathogenicity, thus we investigated the adherent strains found on 4 mm nylon strips, which were ingested and excreted by wild fish specimens. Polymer analysis of the excreted samples shown no signs of degradation, nor have their controls, represented by the nylon strips submerged in the same water tanks. Both the ingested samples and controls presented pathogens in large numbers, revealing the fact that nylon microplastics can be physical carriers for pathogens in the aquatic environment.

Water borne pathogens present a threat to human health and their disinfection from water poses a challenge, prompting search for newer methods and newer materials. Disinfection of Gram-negative bacterium Escherichia coli and Gram-positive coccal bacterium Staphylococcus aureus in aqueous matrix was achieved within 60 and 90 minutes respectively at 35⁰C using solar-photocatalysis mediated by sonochemically synthesized Ag@ZnO core-shell nanoparticles. The efficiency of the process increased with increase in temperature and at 55⁰C the disinfection could be achieved in 45 and 60 min respectively for the two bacteria. A new ultrasound assisted chemical precipitation technique was used for the synthesis of Ag@ZnO core-shell nanoparticles. The characteristics of the synthesized material were established using physical techniques. The material remained stable even at 400o C. Disinfection efficiency of the Ag@ZnO core-shell nanoparticles was confirmed in case of real world water samples from pond, river, municipal tap and was found to be better than that of pure ZnO and TiO2 (Degussa P25). When the nanoparticle based catalyst was recycled and reused for subsequent disinfection experiments, its efficiency did not change remarkably even after three cycles. The sonochemically synthesized Ag@ZnO core-shell nanoparticles have a good potential for application in solar photocatalytic disinfection of water borne pathogens.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

The utilization of titanium dioxide (TiO2) as a photocatalyst for the treatment of wastewater has attracted significant attention in the environmental field. Herein, we have prepared a NH2-MIL-125-derived TiO2@N-doped C Visible Light Catalyst through an in-situ calcination method. The nitrogen element in the organic connector is released through calcination, simul-taneously doping into the sample, thereby enhancing its spectral response to cover the visible region. The as-prepared TiO2@N-doped C catalyst exhibited preserved cage structure even after calcination, thereby alleviating the optical shielding effect and further augmenting its photo-catalytic performance by increasing the reaction sites between the catalyst and pollutants. The calcination time of the TiO2@N-doped C-450 °C catalyst was optimized to achieve a balance be-tween the TiO2 content and nitrogen doping level, ensuring efficient degradation rates for basic fuchsin (99.7%), Rhodamine B (89.9%), and tetracycline hydrochloride (93%) within 90 minutes.

The electron Transport layer (ETL) plays a crucial role in solar cell technology, particularly in perovskite solar cells (PSCs), where nanostructured TiO2 films have been investigated as superior ETL’s compared to compact TiO2. In this study we explore the nanocolumnal growth of TiO2 in the anatase phase, for bilayer thin films by magnetron sputtering (MS) technique and glancing angle deposition (GLAD). By optimizing the growth parameters, we achieved the formation of TiO2 nanocolumns with a cross-sectional diameter ranging from 50 to 75 nm. The average thickness of the films exceeded 12.71 ± 0.5µm , while the filaments exhibited an inclination angle close to 70◦ , corresponding to the deposition angle. Furthermore, we observed a correlation between the quality of the initial layer and enhanced growth of the TiO2 nanocolumns.

In order to improve the strength of PVA/xylan composite films and endow them with ultraviolet (UV) shielding ability, TiO2-KH550 nanoparticle was synthesized and added into the PVA/xylan matrix. The TiO2-KH550 nanoparticle dispersed well in the 0.04% sodium hexametaphosphate (SHMP) solution under ultrasonic and stirring treatments. Investigations on the properties of films showed that TiO2-KH550 had the positive impact on improving the strength, moisture and oxygen barrier properties of the composite films. The maximum tensile strength (27.3 MPa), the minimum water vapor permeability (2.75×10-11 g•m-1•s-1•Pa-1) and oxygen permeability (4.013 cm3•m-2•24h-1•0.1MPa-1) were obtained under the addition of 1.5% TiO2-KH550. The tensile strength of TiO2-KH550 reinforced composite film was increased by 70% than that of the pure PVA/xylan composite film, and the water vapor and oxygen permeability were decreased by 31% and 41%, respectively. Moreover, the UV transmittance of film at the wavelength of 400 nm was almost zero when adding 1.5~2.5% of TiO2-KH550, which indicated the PVA/xylan composite films were endowed with excellent UV light shielding ability.

Nitric acid is a key component in the production of nitrate fertilisers and is industrially produced using the Ostwald process. The Ostwald process can be further intensified by oxidising nitric oxide to nitrogen dioxide using heterogeneous catalysts. We have explored various monometallic and bimetallic catalysts for NO to NO2 oxidation and found ruthenium supported on ceria, containing 10 wt.% manganese to be a promising catalyst for oxidising NO to NO2 at low temperatures at industrially relevant conditions. For a feed comprising 10% NO, 6% O2, 15% H2O and rest Ar, and 8% NO, 2% NO2 5% O2, 15% H2O and rest Ar, the ruthenium-manganese catalysts attained NO-NO2 equilibrium below 400∘C. For the 5wt.% ruthenium and 10 wt.% manganese on ceria catalyst, an apparent activation energy of 39.4 kJ/mol and 85.4 kJ/mol were observed in the absence and presence of NO2, respectively. These findings demonstrate the potential of supported bimetallic ruthenium-manganese catalysts for efficient oxidation of NO to NO2 at low temperatures which can lead to significant process intensification of nitric acid plants.

CuO/ZnO/Al2O3 catalyst is a commonly used catalyst for rea methanol steam reforming reaction. Oxalic acid was as precipitant in preparing oxalate precursor of CuO/ZnO/Al2O3 catalyst by co-precipitation, deionized water and ethanol were as solvents, microwave irradiation and water bath were as aging heating manner respectively. It indicated that ethanol selected crystal phase composition of oxalate precursors and restricted their growth. Microwave irradiation prompted the isomorphous substitution between Cu2+ of CuC2O4 and Zn2+ of ZnC2O4 in mother liquid, forming the master phase (Cu,Zn)C2O4 in precursor, the solid solution Cu-O-Zn formed after calcination, which exhibited nano-fibriform morphology. It possessed small CuO grains, large surface area and strong synergy between CuO and ZnO, which is beneficial to improve the catalytic performance of methanol steam reforming, the STY of H2 reached 516.7 mL·g-1·h-1, and the selectivity of CO was only 0.29%.

Using the colloidal method, Au NP’s were deposited onto 6 different supports (TiO2,  and -Al2O3, HFeO2, CeO2, and C), and their catalytic activity and selectivity were compared in the alkylation of aniline by benzyl alcohol. Correlations were made between the nature of the support, the Au NP size and H-binding energy.

For some decades, the scientific community has been looking for alternatives to the use of fossil fuels that allow the planet's sustainable and environmentally friendly development. To do this, attempts have been made to mimic some processes that occur in nature, among which the photosystem-II stands out, which allows water splitting operating with different steps to generate oxygen and hydrogen. This research presents promising results using synthetic catalysts, which try to simulate some natural processes, and which are based on Au@ZnO-graphene compounds. These catalysts were prepared by incorporating different amounts of gold nanoparticles (1 wt.%, 3 wt.%, 5 wt.%, 10 wt.%) and graphene (1 wt.%) on the surface of synthesized zinc oxide nanowires (ZnO NWs), and zinc oxide nanoparticles (ZnO NPs), along with a commercial form (commercial ZnO) for comparison purposes. The highest amount of hydrogen (1,127 µmol/hg) was reported by ZnO NWs with a gold and graphene loadings of 10 wt.% and 1 wt.%, respectively, under irradiation at 400 nm. Quantities of 759 µmol / hg and 709 µmol / hg were obtained with catalysts based on ZnO NPs and commercial ZnO, respectively. The photocatalytic activity of all composites increased with respect to the bare semiconductors, being 2.5 times higher in ZnO NWs, 8.8 times for ZnO NPs and 7.5 times for commercial ZnO. The high photocatalytic activity of the catalysts is attributed, mainly, to the synergism between the different amount of gold and graphene incorporated, and the surface area of the composites.

The bio-oil was largely produced by thermal pyrolysis of Jatropha-derived biomass wastes (denoted as Jatropha bio-oil) using a Pilot Plant with a capacity of 20 kg h-1 at Thailand Institute of Scientific and Technological Research (TISTR), Thailand. Jatropha bio-oil is an unconventional type of bio-oil, which is mostly composed of fatty acids, fatty acid methyl esters, fatty acid amides and derivatives, and consequently it contained large amounts of heteroatoms (oxygen ~ 20 wt.%, nitrogen ~ 5 wt.%, sulfur ~ 1000 ppm.). The heteroatoms, nitrogen especially, are highly poisonous to the metal or sulfide catalysts for upgrading of Jatropha bio-oil. To overcome this technical problem, we reported a stepwise strategy for hydrotreating of 100 wt% Jatropha bio-oil over mesoporous sulfide catalysts of CoMo/γ-Al2O3 and NiMo/γ-Al2O3 to produce drop-in transport fuels, such as gasoline- and diesel-like fuels. This study is very different from our recent work on co-processing of Jatropha bio-oil (ca. 10 wt%) with petroleum distillates to produce a hydrotreated oil as a diesel-like fuel (Chen et al., Catalysts 2018, 8, 59; http://dx.doi.org/10.3390/catal8020059). Jatropha bio-oil was pre-treated through a slurry-type high pressure reactor under severe condition, resulting in a pre-treated Jatropha bio-oil with relatively low amounts of heteroatoms (oxygen < 20 wt.%, nitrogen < 2 wt.%, sulfur < 500 ppm.). The light and middle distillates of pre-hydrotreated Jatropha bio oil was then separated by distillation at temperature below 240 oC, and the temperature of 240-360 oC. Deep hydrotreating of light distillates over sulfide CoMo/γ-Al2O3 catalyst was performed on a batch-type high pressure reactor at 350 oC and 7 MPa of H2 gas for 5 h. The hydrotreated oil was a gasoline-like fuel, which contained 29.5 vol.% of n-paraffins, 14.4 vol.% of iso-paraffins, 4.5 vol.% of olefins, 21.4 vol. % of naphthene compounds and 29.6 wt.% of aromatic compounds, and little amounts of heteroatoms (nearly no oxygen and sulfur, and less than 50 ppm of nitrogen), corresponding to an octane number of 44, and it would be suitable for blending with petro-gasoline. The hydrotreating of middle distillates over sulfide NiMo/γ-Al2O3 catalyst using the same reaction condition produced a hydrotreating oil with diesel-like composition, low amounts of heteroatoms (no oxygen and less than 50 ppm of sulfur and nitrogen), and a cetane number of 60, which would be suitable for use in drop-in diesel fuel.

The present work describes the synthesis, characterization and photomineralization activity of synthesized Ce1-xZnxO2-x solid solution catalysts allowing the degradation of Diclofenac as a model of anti-inflammatory medicines in water. Oxygen deficient photocatalysts Ce1-xZnxO2-x (CeZnx), produced with mixing ZnO and CeO2 have been characterized for their crystallographic parameters, specific surface area and morphology. Photomineralization activity determinations using TOC analysis have shown efficient diclofenac photooxidation under sunlight. Moreover, results indicate that coexistence of Zn2+, Ce4+ and oxygen vacancies rate in CeZnx solid solution are key factors for strong drug mineralization. Finally, CeZn0.1 which is one of the photocatalysts synthesized in the present work represents a cheap and efficient reagent for organic matter photomineralization in wastewater.

Co/TiO2 catalysts with different cobalt loadings (3.8, 7.5 and 15 wt%) were prepared by impreg-nation method of Co(NO3)2 .6H2O over titania. Samples containing Co(NO3)2 .6H2O and TiO2 in stoichiometric proportions in order to obtain CoTiO3 and Co2 TiO4 phases were also synthesized. The effect of the calcination treatment at two different temperatures, 550 and 1150 °C was investigated. Characterizations by several techniques, such as XRD UV-vis-NIR, DRS, Raman and XPS were carried out. XRD showed the coexistence of three phases: CoTiO3; Co2TiO4 and Co3O4 after calci-nation at 550°C, while the calcination at high temperature (1150°C) leads to single-phase systems (CoTiO3 or Co2TiO4). Diffuse reflection and XPS spectroscopy showed that divalent cobalt occupies octahedral sites in the ilmenite phase and both tetrahedral and octahedral sites in the spinel phase. The catalytic performances of the prepared catalysts, calcined at the two different temperatures, were evaluated in the oxidative dehydrogenation reaction (ODH) of ethane to ethylene. The con-version values were almost comparable for all the samples, calcined at 550 °C, and comparable the ethylene selectivity were recorded, slightly higher only in the case of CoTiO3. The calcination at 1150°C did not modify the overall activity (ethane conversion values around 20%), however, the production of COx becomes more significant. The study examined the influence of the reaction mixture composition, specifically the presence of water, and reveals a slight increase in the yield of ethylene accompanied by a decrease in the overall catalyst activity. This behavior is likely attributed to an increase in the surface concentration of hydroxyl species (OH), resulting in heightened surface acidity.

Compared with precious metal catalysts, non-platinum catalysts have the advantages of low cost and high performance. Among them, the activated carbon (AC) with a large specific surface area (SSA) can be used as a carrier or as a carbon source of nonprecious metal/carbon system catalyst at the same time. Therefore, this paper uses cheap pine peel bio-based materials to prepare large surface area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon catalyst. The merits include AC@CoPc composite catalysts are prepared by precisely controlling the composite proportion of AC and CoPc, the atomically dispersed Co nanoparticles form and synergistically with N promote the exposure of CoNx active sites, and the Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.01 V, which is higher than Pt/C (20 wt%) catalyst. Apart from this, the stability is 87.8% in 0.1 M KOH after 20000 s testing in compared with other AC@CoPc series catalysts and Pt/C (20 wt%) catalyst. Considering from the performance and price of the catalyst in practical application, these composite catalysts combine biomass carbon materials with phthalocyanine series, which will be widely used in the area of nonprecious metal catalysts.

The methanation of CO2 is of great interest in power-to-gas systems and contributes to the mitigation of climate change through carbon dioxide capture and the subsequent production of high value-added products. This study investigated CO2 methanation with three Ni catalysts supported on Al2O3 and ZrO2, which were simulated using a mathematical model of a packed bed reactor designed based on their chemical kinetics reported in the literature. The simulated reactive system was fed with syngas obtained from residual coffee pulp, obtained after solvent phytochemical extraction process, under several gasification conditions. The results reflect a high incidence of catalyst support, preparation method, and syngas composition on CO2 conversion and CH4 selectivity. For all the syngas compositions, Ni/ZrO2 catalysts show the best values for CO2 conversion and CH4 selectivity for Ni/Al2O3 catalyst.

A unique method for synthesizing a surface modifier for metallic hydrogen permeable mem-branes based on non-classic bimetallic pentagonally structured Pd-Pt nanoparticles has been de-veloped. It was found that nanoparticles had unique hollow structure. This significantly reduces the cost of their production due to economical use of metal. According to the results of electro-chemical studies, synthesized bimetallic Pd-Pt/Pd-Ag modifier showed excellent catalytic activi-ty (up to 60.72 mA cm–2), long-term stability and resistance to COads poisoning in alkaline oxida-tion reaction of methanol. The membrane with pentagonally structured Pd-Pt/Pd-Ag modifier showed the highest hydrogen permeation flux density up to 27.3 mmol s–1 m–2. Obtained hy-drogen flux density were 2 times higher than that for membranes with classic Pdblack/Pd-Ag modifier and an order of magnitude higher than that for unmodified membrane. Since the rate of transcrystalline hydrogen transfer through a membrane increased, while the speed of transfer through defects remained unchanged, a one and a half times rise in selectivity of the developed Pd-Pt/Pd-Ag membranes was recorded and it amounted to 3514. Achieved results are due to both the synergistic effect of the combination of Pd and Pt metals in the modifier composition and the large number of available catalytically active centers, which are present as a result of non-classic morphology with high-index facets. The specific faceting, defect structure and unusual properties provide great opportunities for the application of nanoparticles in the areas of membrane reac-tors, electrocatalysis, petrochemical and hydrogen industries.

Mixtures of ethanol and methanol being synthesized from CO2 and green H2 can serve as sustainable base chemicals for a number of chemical processes. Amongst these processes, the catalytically-supported synthesis of CO2-neutral C4 to C10 alcohols is of increasing importance as, e.g., iso-butanol can be used as a drop-in fuel or after dehydration to produce iso-butene as a feedstock for the synthesis of plastics. 2-ethyl-hexanol can be further refined into solvents, tensides, or monomers. In this respect, NiPt alloys on an activated carbon support were found to be active and stable catalysts for the synthesis of iso-butanol following the Guerbet reaction scheme. In this study, two different routes are applied to the synthesis of these NiPt catalysts: a more conventional one based on the impregnation of Ni and Pt salts and an advanced path with a surface redox reaction between elemental Ni on the support and Pt ions in a polar solution. The experimental evaluation showed that the Pt particles from the surface redox reaction being exposed on the Ni particles are more active than those on the impregnated catalysts due to their high surface energy. Their specific space-time yields were 10–20 times higher.

This research investigates the difference on the products obtained through two hydrothermal carbonization treatments. Our aim is to synthesize metal-free, carbon-based catalysts for the Oxygen Reduction Reaction (ORR) to serve as efficient and cost-effective alternatives to plati-num-based catalysts. Catalysts synthesized using the traditional hydrothermal approach exhibit a higher electrocatalytic activity for ORR in alkaline media, despite a more energy-intensive pro-duction process. The superior performance is attributed to differences in particle morphology and to the chemical composition of the particle surfaces. The presence of functional groups on the surfaces of catalysts obtained via traditional approach significantly enhances ORR activity by fa-cilitating deprotonation reactions in an alkaline environment. Our research aims to be a reference for future investigations, shifting the focus to the fine-tuning of surface chemical compositions and morphologies of metal-free catalysts to enhance ORR activity.

The presence of azo dyes in textile effluents is an issue of major concern due to their potential impact on the environment and human health. In this study we investigate the photocatalytic degradation under visible light of Reactive Violet 5 (RV5), an azo dye widely used in the textile industry. A preliminary screening of different titania-based catalysts was carried out to identify the best candidate for RV5 removal. The selected catalyst was then tested in a stirred and aerated lab-scale reactor illuminated with a light LED source (λmax = 460 nm). The effects of pH, catalyst load and hydrogen peroxide additions on the efficiency of dye removal were evaluated. Under the best conditions (pH 10, 3 g/L of catalyst and 60 mM hydrogen peroxide), the dye solution was completely decolorized in about 2 h. Overall, the results obtained suggest that the proposed process may represent a suitable method for the removal of RV5 from textile effluents.

The method of micro-arc oxidation has been utilized to synthesize a protective biocompatible coating for a bioresorbable orthopedic Mg implant. This paper presents the results of a comprehensive research of micro-arc coatings based on diatomite – a biogenic material consisting of shells of diatom microalgae. The main focus of this study was the functionalization of diatomite-based micro-arc coatings by incorporating the particles of titania (TiO2) into them. Various properties of the resulting coatings were examined and evaluated. The XRD analysis has revealed the formation of a new magnesium orthosilicate phase – forsterite (Mg2SiO4). It has been established that the corrosion current density of the coatings has decreased by 2-4 orders of magnitude after the inclusion of TiO2 particles, depending on the coating process voltage. The adhesion strength of the coatings has increased following the particle incorporation. The processes of dissolution of both coated and uncoated samples in a sodium chloride solution were studied. The in vitro cell viability was assessed, which showed that the coatings significantly reduce the cytotoxicity of Mg samples.

The physiological characteristics of liquid digestate retrieved from various biogas plants based in northern Greece are presented. Preliminary photocatalysis experiments on inoculated liquid di-gestate sampled showed that disinfection is possible when pre-treated digestate with a combination of centrifuge-flocculation-μFiltration after 5.5 hours of 0.7g/L suspended TiO2 under UVA illumination for the experimental conditions is used. A novel design photocatalytic nanofiltration reactor was implemented for disinfection experiments on pre-treated liquid digestate, giving promising results. This work sets the basis for the efficient operation and engineering application of technology collaboration with photocatalysis as the final step for liquid digestate sanitation and reusable water recovery.

Wound infections evidently appeared in times of World War I that accounted a significant mortality and morbidity rate among injured soldiers. Currently, around 11 million people worldwide require medical treatment for wound infections and 300,000 die every year due to untreated wound infection. The extensive use of antibiotics to treat wound infection leads to emerging new microbial strains that are resistant to many antibiotics. There is a growing concern on the emergence and re-emergence of drug-resistant pathogens such as multi-resistant bacterial strains. Hence, the development of new antimicrobial compounds or the modification of those that already exist to improve antibacterial activity is a high priority area of research. During the past few decades, nanotechnology has arisen with new promising technology for synthesis of nanobiomaterials. Metallic nanoparticles (NPs) are considered as new alternative treatment with superior antibacterial activity. In this study, new formulation of titanium oxide (TiO2) NPs with different sizes were synthesized and characterized. Genotoxicity, mutagenicity and antibacterial activities of TiO2 NPs against the causative agents of wound infection were investigated. Antibacterial activity of TiO2 NPs was conducted against three ATCC ® bacterial strains: methicillin-resistant Staphylococcus aureus (MRSA), Escherichia coli and Pseudomonas aeruginosa. The results clearly illustrate a superior antibacterial activity of all newly formulated TiO2 NPs against the most causative agents of wound infection. Most of our TiO2 NPs showed non-genotoxic and non-mutagenic results at the maximum concentrations. Findings of this study will enhance the future of the therapeutic strategies against the resistant pathogenic strains that cause wound infections.